Yamaha R-N803 de handleiding

Categorie
Audiotuners
Type
de handleiding

Deze handleiding is ook geschikt voor

G
Owner's Manual
EN
The R-N803 and R-N803D network receivers allow you to play back sound in
high-quality stereo at your own home.
This manual explains preparations and operations for everyday users of the unit.
Network Receiver
i En
English
PLEASE READ CAREFULLY BEFORE USE. BE SURE TO FOLLOW THESE INSTRUCTIONS.
The precautions listed below are to prevent risk of harm to the user and others, as well as to prevent property
damage, and to help the user use this unit properly and safely. Be sure to follow these instructions.
After reading this manual, be sure to keep it in a safe place where
it can be referenced at any time.
WARNING
This content indicates “risk of serious injury or death.
Power supply/power cord
Do not do anything that could damage the power cord.
- Do not place it near a heater.
- Do not bend it excessively or alter it.
- Do not scratch it.
- Do not place it under a heavy object.
Using the power cord with the core of the cord exposed could
cause electric shocks or a fire.
Do not touch the power plug or cord if there is a chance of
lightning. Failure to observe this may cause electric shocks.
Use this unit with the power supply voltage printed on it.
Failure to connect to an appropriate AC outlet may cause a fire,
electric shocks, or malfunctions.
Be sure to use the supplied power cord. Also, do not use the
supplied power cord for other units. Failure to observe the
above may cause a fire, burns, or malfunctions.
Check the electric plug periodically and remove any dirt or dust
which may have accumulated on it. Failure to observe this may
cause a fire or electric shocks.
When setting up the unit, make sure that the AC outlet you are
using is easily accessible. If some trouble or malfunction
occurs, immediately turn off the power switch and disconnect
the plug from the AC outlet. Even when the power switch is
turned off, as long as the power cord is not unplugged from the
wall AC outlet, the unit will not be disconnected from the
power source.
If you hear thunder or suspect approaching lightning, quickly
turn off the power switch and pull the power plug from the AC
outlet. Failure to observe this may cause a fire or malfunctions.
If not using the unit for long periods of time, be sure to pull the
power plug from the AC outlet. Failure to observe this may
cause a fire or malfunctions.
Do not disassemble
Do not disassemble or modify this unit. Failure to observe this
may cause a fire, electric shocks, injury, or malfunctions. If you
notice any irregularities, be sure to request an inspection or
repair from the dealer where you purchased the unit or from
qualified Yamaha service personnel.
Water warning
Do not expose the unit to rain, use it near water or in damp or
wet conditions, or place on it any containers (such as vases,
bottles or glasses) containing liquids which might spill into any
openings. A liquid such as water getting into the unit may cause
a fire, electric shocks, or malfunctions. If any liquid such as
water seeps into the device, turn off the power immediately and
unplug the power cord from the AC outlet. Then, request an
inspection from the dealer where you purchased the unit or from
qualified Yamaha service personnel.
Never insert or remove an electric plug with wet hands. Do not
handle this unit with wet hands. Failure to observe this may
cause electric shocks or malfunctions.
Fire warning
Do not place any burning items or open flames near the unit,
since they may cause a fire.
Maintenance and care
Do not use aerosols or spray-type chemicals that contain
combustible gas for cleaning or lubrication. The combustible
gas will remain inside the unit, which may cause explosion or
fire.
Battery use
Do not disassemble a battery. If the contents of the battery get
on your hands or in your eyes, it can cause blindness or
chemical burns.
Do not dispose of batteries in fire. Doing so may result in the
battery bursting, causing a fire or injury.
Do not expose a battery to high temperatures, such as direct
sunlight or a fire. The battery may burst, causing a fire or injury.
Do not attempt to recharge batteries that are not intended to be
charged. Charging could cause the battery to burst or leak,
which can cause blindness, chemical burns, or injury.
If the batteries do leak, avoid contact with the leaked fluid.
If the battery fluid should come in contact with your eyes,
mouth, or skin, wash immediately with water and consult a
doctor. Battery fluid is corrosive and may possibly cause loss of
sight or chemical burns.
Wireless unit
Do not use this unit near medical devices or inside medical
facilities. Radio waves from this unit may affect electro-
medical devices.
Do not use this unit within 15 cm (6 in) of persons with a heart
pacemaker implant or a defibrillator implant. Radio waves from
this unit may affect electro-medical devices, such as a heart
pacemaker implant or defibrillator implant.
If you notice any abnormality
If any of the following abnormalities occur, immediately turn
off the power and disconnect the power plug. If you are using
batteries, remove the batteries from this unit.
- The power cord/plug is damaged.
- An unusual smell or smoke is emitted from the unit.
- Foreign material gets into the interior of the unit.
PRECAUTIONS
Be sure to request inspections or repairs from the dealer
where you purchased the unit or from qualified Yamaha
service personnel.
Yamaha cannot be held responsible for damage caused by
improper use or modifications to the unit.
This product is for ordinary homes. Do not use for
applications requiring high reliability, such as managing
lives, health care or high-value assets.
ii En
PRECAUTIONS
English
- There is a loss of sound during use.
- There is a crack or damage in the unit.
Continued use could cause electric shocks, a fire, or
malfunctions. Immediately request an inspection or repair from
the dealer where you purchased the unit or from qualified
Yamaha service personnel.
Be careful not to drop or apply strong impact to this unit. If you
suspect the unit may have been damaged due to dropping or
impact, immediately turn off the power and pull the power plug
from the AC outlet. Failure to observe this may cause electric
shocks, a fire, or malfunctions. Immediately request an
inspection from the dealer where you purchased the unit or from
qualified Yamaha service personnel.
CAUTION
This content indicates “risk of injury.
Power supply/power cord
Do not use an AC outlet where the power plug fits loosely when
inserted. Failure to observe this may cause a fire, electric
shocks, or burns.
When removing the electric plug from the unit or an AC outlet,
always hold the plug itself and not the cord. Pulling by the cord
can damage it and cause electric shocks or a fire.
Insert the power plug firmly all the way into the AC outlet.
Using the unit when it is not plugged in sufficiently can cause
dust to accumulate on the plug, causing a fire or burns.
Installation
Do not place the unit in an unstable position where it might
accidentally drop or fall over and cause injuries.
Do not block this unit's ventilation holes (cooling slits). This
unit has ventilation holes on the top/bottom to prevent the
internal temperature from becoming too high. Failure to
observe this may trap heat inside the unit, causing a fire or
malfunctions.
When installing this unit: - Do not cover it with any cloth.
- Do not install it on a carpet or rug.
- Make sure the top surface faces up; do not install on its sides
or upside down.
- Do not use the device in a confined, poorly-ventilated
location.
Failure to observe the above may trap heat inside the unit,
causing a fire or malfunctions. Ensure that there is adequate
space around the unit: at least 30 cm (11-3/4 in) on top, 20 cm
(7-7/8 in) on the sides, and 20 cm (7-7/8 in) on the rear.
Ensure that the top is facing upwards. Failure to observe this
may cause malfunctions or for the unit to fall and cause injury.
Do not place the unit in a location where it may come into
contact with corrosive gases or salt air. Doing so may result in
malfunction.
Avoid being near the unit during a disaster, such as an
earthquake. Since the unit may turn over or fall and cause
injury, quickly move away from the unit and go to a safe place.
Before moving this unit, be sure to turn off the power switch
and disconnect all connection cables. Failure to observe this
may damage the cables or cause you or someone else to trip and
fall.
When transporting or moving the unit always use two or more
people. Attempting to lift the unit by yourself may damage your
back, result in other injury, or cause damage to the unit itself.
Hearing loss
Do not use the unit/speakers or headphones for a long period of
time at a high or uncomfortable volume level, since this can
cause permanent hearing loss. If you experience any hearing
loss or ringing in the ears, consult a physician.
Before connecting the unit to other devices, turn off the power
for all devices. Also, before turning the power of all devices on
or off, make sure that all volume levels are set to the minimum.
Failing to do so may result in hearing loss, electric shock, or
device damage.
When turning on the AC power in your audio system, always
turn on the unit LAST, to avoid hearing loss and speaker
damage. When turning the power off the unit should be turned
off FIRST for the same reason. Failure to observe the above
may cause hearing impairment or speaker damage.
Maintenance
Remove the power plug from the AC outlet when cleaning the
unit. Failure to observe this may cause electric shocks.
Handling caution
Do not insert foreign materials such as metal or paper into the
ventilation holes of this unit. Failure to observe this may cause a
fire, electric shocks, or malfunctions. If foreign material gets
into the unit, immediately shut off the power and pull the power
plug from the AC outlet / then turn off any amplifiers and
receivers and request an inspection from the dealer where you
purchased the unit or from qualified Yamaha service personnel.
Do not rest your weight on the unit or place heavy objects on it.
Avoid applying excessive force to the buttons, switches or
connectors. Failure to observe the above may cause injury or
unit damage.
Avoid pulling the connected cables to prevent injuries or
damage to the unit by causing it to fall.
Battery use
Always replace all batteries at the same time. Do not use new
batteries together with old ones. Using new ones with old ones
could cause a fire, burns, or inflammation due to fluid leaks.
Do not mix battery types, such as alkaline batteries with
manganese batteries, or batteries from different makers, or
different types of batteries from the same maker, since this can
cause a fire, burns, or inflammation due to fluid leaks.
Keep batteries away from children. A child could accidentally
swallow a battery. Failure to observe this may also cause
inflammation due to battery fluid leaks.
Do not put in a pocket or bag, carry, or store batteries together
with pieces of metal. The battery could short, burst, or leak,
causing a fire or injury.
Always make sure all batteries are inserted in conformity with
the +/- polarity markings. Failure to do so might result in a fire,
burns, or inflammation due to fluid leaks.
When the batteries run out, or if the unit is not to be used for a
long time remove the batteries from the remote control to
prevent possible leakage of the battery fluid.
When storing or discarding batteries, insulate the terminal area
by applying tape, or some other protection. Mixing them with
other batteries or metal objects can cause a fire, burns, or
inflammation due to fluid.
Caution
Do not touch the surface marked with
this label.
The surface may become hot during
operation.
iii En
Notice
Indicates points that you must observe in order to
prevent product failure, damage or malfunction and
data loss, as well as to protect the environment.
Power
If not using the unit for a long period of time, be sure to pull the
power plug from the outlet. Even if the A (Standby/On) switch
has been turned off, a minute current is still flowing.
Installation
Do not use this unit in the vicinity of other electronic
equipment, such as a TV, radio, AV unit, or mobile phone.
Failure to observe this may cause this unit or the TV or radio to
produce noise.
Do not use this unit in a location that is exposed to direct
sunlight (such as a vehicle interior), that becomes extremely
hot, such as near a heater, or extremely cold, or that is subject to
excessive dust or vibration. Failure to observe this may cause
the unit's panel to become deformed, the internal components to
malfunction, or for operation to become unstable.
Install this unit as far away from other electronic equipment as
possible. Digital signals from this unit may interfere with other
electronic equipment.
If using a wireless function, avoid installing this unit near metal
walls or desks, microwave ovens, or other wireless devices.
Connections
If connecting external units, be sure to thoroughly read the
manual for each unit and connect them in accordance with the
instructions. Failure to properly handle a unit in accordance
with the instructions could cause malfunctions.
Do not connect this unit to industrial units. Digital audio
interface standards for consumer use and industrial use are
different. This unit has been designed to connect to a consumer-
use digital audio interface. Connections to an industrial-use
digital audio interface could not only cause this unit to
malfunction, but could also damage the speakers.
Handling
Do not place vinyl, plastic, or rubber products on this unit.
Failure to observe this may cause discoloration or deformation
in the panel of this unit.
If the ambient temperature changes drastically (such as during
unit transportation or under rapid heating or cooling) and there
is a chance condensation may have formed in the unit, leave the
unit for several hours without turning on the power until it is
completely dry before use. Using the unit while there is
condensation can cause malfunctions.
Maintenance
When cleaning the unit, use a dry, soft cloth. Using chemicals
such as benzine or thinner, cleaning agents, or chemical
scrubbing cloths can cause discoloration or deformation.
Batteries
Be sure to discard used batteries in accordance with local
regulations.
Information
Indicates information of note regarding this product.
About content in this manual
The illustrations and screens in this manual are for instructional
purposes only.
The company names and product names in this manual are the
trademarks or registered trademarks of their respective
companies.
Software may be revised and updated without prior notice.
Information marked by the WARNING” icon indicates
points that may lead to death or serious injury if not observed.
Information marked with the “ CAUTION” icon indicates
points that may lead to injury if not observed.
Information in the “Notice” sections indicates points that you
must observe to prevent product failure, damage or malfunction
and data loss.
Information listed in the “Note” sections indicates
supplementary information.
This manual describes the “iPhone”, “iPad” and “iPod touch”
collectively as the “iPhone”. (“iPhone” refers to the “iPhone”,
“iPad” and “iPod touch”, unless otherwise specified.)
In this manual, illustrations of English menu screens are used as
examples.
Notice and Information
Contents
1 En
English
PREPARATION INTRODUCTION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
INTRODUCTION
What you can do with this unit ................................. 2
Sources that can be played back on this unit ................. 2
Supplied accessories ................................................... 3
Controls and functions ............................................... 4
Front panel ..................................................................... 4
Front display .................................................................. 6
Rear panel ...................................................................... 7
Remote control............................................................... 8
PREPARATION
Connections ............................................................... 10
Connecting audio devices ............................................ 10
Connecting the speakers .............................................. 11
Connecting the FM/AM antennas (R-N803) ............... 13
Connecting the DAB/FM antenna (R-N803D)............ 13
Connecting the network cable ..................................... 14
Preparing a wireless antenna ....................................... 14
Connecting the power cord.......................................... 14
Turning on the unit ...................................................... 14
Connecting to network ............................................. 15
Sharing the iOS device setting..................................... 16
Configuring with the router's WPS push button.......... 17
Set the wireless network connection manually............ 18
Connecting a mobile device to the unit directly
(Wireless Direct) ..................................................... 19
Verify the network connection status .......................... 20
Configuring MusicCast................................................ 20
BASIC OPERATION
Playback .................................................................... 22
Playing a source........................................................... 22
Switching information on the front display................. 22
Front panel operations ................................................. 23
Using the sleep timer ................................................... 24
Listening to FM/AM radio....................................... 25
FM/AM tuning............................................................. 25
Registering favorite radio stations (presets) ................ 25
Radio Data System tuning
(U.K. and Europe models only)............................... 28
Listening to DAB radio (R-N803D)......................... 29
Preparing the DAB tuning ........................................... 29
Selecting a DAB radio station for reception................ 29
Using preset function................................................... 30
Displaying the DAB information................................. 31
Checking reception strength of each DAB channel
label ......................................................................... 31
Playing back music via Bluetooth............................ 32
Connecting a Bluetooth device (pairing) ..................... 32
Playing back Bluetooth device contents ...................... 32
Disconnecting a Bluetooth connection ........................ 33
Playing back music stored on media servers
(PCs/NAS) ............................................................. 34
Setting the media sharing of music files...................... 34
Playback of PC music contents.................................... 35
Listening to Internet radio....................................... 37
Playing back iPhone/iTunes music via a network
(AirPlay) ................................................................ 38
Playback of iPhone/iTunes music contents ................. 38
Playing back music stored on a USB storage
device ......................................................................39
Connecting a USB storage device ............................... 39
Playback of USB storage device contents ................... 39
Registering the current playback song/station
(Preset function) ....................................................41
Registering to a preset ................................................. 41
Recalling a preset......................................................... 41
Clearing a preset .......................................................... 41
ADVANCED OPERATION
Optimizing the speaker settings automatically
(YPAO)...................................................................42
Error messages............................................................. 44
Warning messages ....................................................... 45
Configuring playback settings for different
playback sources (Option menu) .........................46
Option menu items....................................................... 46
Configuring various functions (Setup menu) .........47
Setup menu items......................................................... 48
Network ....................................................................... 48
Bluetooth ..................................................................... 50
YPAO .......................................................................... 50
Volume ........................................................................ 50
AutoPowerStdby (Auto Power Standby)..................... 51
ECO Mode................................................................... 51
Configuring the system settings
(ADVANCED SETUP menu)...............................52
ADVANCED SETUP menu items .............................. 52
Checking the firmware version (VERSION)............... 52
Changing the speaker impedance setting (SP IMP.) ... 52
Selecting the remote control ID (REMOTE ID).......... 52
Setting tuner frequency step (TU) ............................... 53
Restoring the default settings (INIT)........................... 53
Updating the firmware (UPDATE) ............................. 53
Updating the unit’s firmware via the network .......54
ADDITIONAL INFORMATION
Troubleshooting.........................................................55
Error indications on the front display.....................61
Supported devices and file formats .........................62
Supported devices........................................................ 62
Supported file formats ................................................. 62
Trademarks ...............................................................63
Specifications .............................................................64
Index ...........................................................................66
Contents
2 En
INTRODUCTION
This unit is a network receiver compatible with a network source such as a media server and mobile device.
It supports playback from not only audio sources such as a CD player or radio, but also from Bluetooth devices and
network streaming services.
Sources that can be played back on this unit
*
You need a commercially available wireless router (access point) when you use a mobile device.
1 Play back the Internet radio (p. 37)
2 Play back the streaming service
(see the supplement for each service.)
3 Play back music files stored on your PC (p. 34)
4 Play back music files stored on your NAS
(p. 34)
5 Play back music files stored on your iPod/
iTunes with AirPlay (p. 38)
6 Play back audio content from Bluetooth
devices (p. 32)
7 Play back music files stored on your USB
device (p. 39)
8 Play back your external component (p. 10)
9 Listening to radio (p. 25, 29)
Note
For details on connecting the external devices, see “Connections” (p. 10).
What you can do with this unit
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
This unit
1 Internet
2 Streaming service
Modem
Router*
3 PC
5 AirPlay (iTunes)
4 NAS
5 AirPlay
(iPhone/iPad/iPod touch)
6 Bluetooth
7 USB device 8 CD player, etc.
Mobile
device
9 Radio
Supplied accessories
3 En
English
INTRODUCTION
Check that the following accessories are supplied with the product.
Supplied accessories
Remote control FM antenna (R-N803)AM antenna (R-N803) DAB/FM antenna (R-N803D)
YPAO microphone
Power cord
* The supplied power cord
varies depending on the
region of purchase.
Batteries (x2)
(AA, R6, UM-3)
*
One of the above is supplied depending
on the region of purchase.
G
Network Receiver
Réseau Ampli-Tuner
Сетевой ресивер
R-N803/R-N803D
Owner’s Manual
CD-ROM (Europe model)
R-N803D
Quick Start Guide
(Europe model)
G
Network Receiver
R-N803/R-N803D
Owner’s Manual
(except Europe model)
4 En
Front panel
1 A (power)
Turns on/off the unit.
2 Power indicator
Brightly lit: Power is on
Dimly lit: Standby mode
Tuned off: Power is off
Note
When not using this unit for an extended period of time, be sure
to unplug it from the power outlet. This unit uses a minimal
amount of power even in standby mode.
3 Remote control sensor
Receives infrared signals from the remote control.
4 DIMMER
Changes the brightness level of the front display. Choose
brightness from 5 levels by pressing this button
repeatedly.
5 DISPLAY
Selects the information displayed on the front display
(p. 22).
6 MODE
Sets the FM band reception mode to automatic stereo or
monaural (p. 25).
7 MEMORY
Registers the current radio station as a preset when
TUNER is selected as the input source (p. 25, 30).
Registers the current playback song or streaming station
as a preset when NET or USB is selected as the input
source (p. 41).
8 CLEAR
Clears a preset radio station when TUNER is selected as
the input source (p. 27, 30).
Clears a preset song or a preset streaming station when
NET or USB is selected as the input source (p. 41).
9 BAND
Sets the radio tuner band when TUNER is selected as the
input source. (p. 25, 29)
0 Front display
Shows information about the operational status of this unit
(p. 6).
A PRESET j / i
Recalls a preset radio station (p. 27, 30) or song/streaming
station (p. 41).
B TUNING jj / ii
Selects the tuning frequency (p. 25) or a DAB radio
station (p. 29) when TUNER is selected as the input
source.
C PURE DIRECT and indicator
Allows you to listen to a source in the purest possible
sound (p. 23). The indicator above it lights up and the
front display turns off when this function is turned on.
Controls and functions
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
12 3 4 5 6 7 8 9: B CA
5 En
Controls and functions
English
INTRODUCTION
D PHONES jack
Outputs audio to your headphones for private listening.
E YPAO MIC jack
For connecting the supplied YPAO microphone (p. 42).
F SPEAKERS A/B
Turns on or off the speaker set connected to the
SPEAKERS A and/or SPEAKERS B terminals on the rear
panel each time the corresponding button is pressed.
G USB jack
For connecting a USB storage device (p. 39).
H INPUT selector
Selects the input source you want to listen to.
I BASS control
Increases or decreases the low frequency response. The
center position produces a flat response (p. 23).
J TREBLE control
Increases or decreases the high frequency response. The
center position produces a flat response (p. 23).
K BALANCE control
Adjusts the sound output balance of the left and right
speakers to compensate for sound imbalances caused by
speaker locations or listening room conditions (p. 23).
L LOUDNESS control
Retains a full tonal range at any volume level (p. 24).
Note
The LOUDNESS control does not function when the YPAO
Volume function (p. 50) is enabled.
M SELECT/ENTER
Turn the dial to select a numeric value or setting, and press
the dial to confirm.
N RETURN
Returns to the previous indication of the front display.
CONNECT
Use to register this unit to the MusicCast network (p. 20).
O VOLUME control
Increases or decreases the sound output level.
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
OJIHFED K LMNG
6 En
Controls and functions
Front display
Note
If you turn on the power to the unit right after you purchase or
initialize it, the unit will display “WAC” (Wireless Accessory
Configuration) on the front display and trigger an automatic
iOS device search. See “Sharing the iOS device setting” (p. 16)
for details on the iOS device and network connection.
You can change the brightness level of the front display by
pressing DIMMER on the front panel (p. 4).
1 Information display
Displays the current status (such as input name).
You can switch the information that is displayed when you
press DISPLAY on the front panel (p. 22).
2 Bluetooth indicator
Lights up when the unit is connecting to a Bluetooth
device.
3 Signal strength indicator
Lights up when the unit connects to a wireless network or
operates as an access point. The strength of the wireless
network signal can be verified by the indicator status.
4 SLEEP indicator
Lights up when the sleep timer is on (p. 24).
5 STEREO indicator
Lights up when the unit is receiving a stereo FM radio
signal.
6 TUNED indicator
Lights up when the unit is receiving an FM/AM radio
station signal.
7 YPAO VOL. indicator
Lights up when the YPAO volume (p. 50) function is
enabled.
The YPAO volume function is automatically enabled after
YPAO is performed.
8 A/B indicators
“A” lights up when the SPEAKERS A output is enabled
and “B” lights up when the SPEAKERS B output is
enabled.
9 Volume indicator
Indicates the current volume.
0 Cursor indicators
Indicate the remote control cursor keys currently
operational.
A Speaker indicators
Indicate the speakers from which signals are output during
YPAO.
A Front speaker (L)
S Front speaker (R)
L Subwoofer
B MUTE indicator
Blinks when audio is muted.
VOL. MUTE
TUNED
SLEEP
YPAO VOL.
STEREO
SW
L R
AB
1 9
: A: B
2
3 6 7854
7 En
Controls and functions
English
INTRODUCTION
Rear panel
1 LINE 1-3 jacks
For connecting to analog audio components (
p. 10
).
2 PHONO jacks
For connecting to a turntable (p. 10).
3 OPTICAL 1/2 jacks
For connecting to audio components equipped with
optical digital output (p. 10).
4 COAXIAL 1/2 jacks
For connecting to audio components equipped with a
coaxial digital output (p. 10).
5 NETWORK jack
For connecting to a network with a network cable (p. 14).
6 Wireless antenna
For connecting to a network device wirelessly (p. 14).
7 VOLTAGE SELECTOR (General models only)
Selects the switch position according to your local voltage
(p. 14).
8 AC IN jack
For connecting the supplied power cord (p. 14).
9 CD jacks
For connecting to a CD player, etc. (p. 10).
0 ANTENNA terminals
For connecting to the radio antennas (p. 13).
A TRIGGER OUT jacks
For connecting to a subwoofer that supports the trigger
function (p. 10).
B SUBWOOFER OUT jack
For connecting to a subwoofer with built-in amplifier
(p. 10).
C SPEAKERS terminals
For connecting to speakers (p. 10).
A
B
SPEAKERS
NETWORK
COAXIALOPTICAL
FM AM
75Ω
ANTENNA
SUBWOOFER
OUT
TRIGGER
OUT
IN
2
IN
1
IN
OUT
OUT
3
12 12
CD
PHONO
LINE
GND
1 2V 0.1A
AC IN
381 2 4 5 6
9
7
A B C:
(R-N803)
8 En
Controls and functions
Remote control
1 Infrared signal transmitter
Sends infrared signals.
2 SPEAKERS A/B
Turns on and off the set of speakers connected to the SPEAKERS
A and/or SPEAKERS B terminals on the rear panel of this unit
when the corresponding key is pressed.
3 Input selection keys
Select an input source for playback.
PHONO PHONO jacks
COAX 1/2 COAXIAL1/2 jacks
BLUETOOTH Bluetooth connection
OPT 1/2 OPTICAL 1/2 jacks
CD CD jacks
LINE 1-3 LINE 1-3 jacks
TUNER (R-N803) FM/AM tuner
(R-N803D) FM/DAB tuner
NET Network source (press repeatedly to select a
desired network source)
USB USB jack (on the front panel)
4 Radio keys
Operate the radio.
BAND Sets the radio tuner band when TUNER is
selected as the input source. (p. 25, 29)
TUNING jj/ii Selects the tuning frequency (p. 25) or a DAB
radio station (p. 29) when TUNER is selected
as the input source.
5 Preset keys
MEMORY Registers the current radio station as a preset
when TUNER is selected as the input source
(p. 25, 30).
Registers the current playback song or
streaming station as a preset when NET or
USB is selected as the input source (p. 41).
PRESET j/i Recalls a preset radio station (p. 27, 30) or
song/streaming station (p. 41).
6 Menu operation keys
Cursor keys Select menus and parameters, etc.
(B/C/D/E)
ENTER Confirms a selected item.
RETURN Returns to the previous state.
7 HOME
Moves up top level when selecting music files, folders, etc.
8 SETUP
Displays the “Setup” menu (p. 47).
9 NOW PLAYING
Displays music information when selecting music files, folders,
etc.
0 VOLUME +/-
Adjust the volume.
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
SLEEP
PHONO
B
A
SPEAKERS
OPTION
A
B
C
D
E
1
3
6
7
0
8
9
2
4
5
9 En
Controls and functions
English
INTRODUCTION
A A (power)
Turns on/off (standby) the unit.
Note
The A (power) key on the remote control works only when the A
(power) on the front panel is on.
B SLEEP
Sets the sleep timer (p. 24).
C OPTION
Displays the “Option” menu (p. 46).
D MUTE
Mutes the audio output.
E Playback keys
Let you play back and perform other operations for network
sources, Bluetooth devices and USB devices.
Note
The playback keys may not work depending on the Bluetooth
device.
Installing batteries
Note
Change all batteries if the operation range of the remote control
narrows.
Before inserting new batteries, wipe the compartment clean.
Operation range
The remote controls transmit a directional infrared beam.
Be sure to aim the remote controls directly at the remote
control sensor on the front panel of this unit.
30° 30°
Remote control
Approximately
6 m (20 ft)
10 En
PREPARATION
Connecting audio devices
Make sure to connect L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will
be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and
lack bass. Refer to the owners manual for each of your components.
Make sure to use RCA cables, optical cables, or coaxial cables to connect audio components.
CAUTION
Do not connect this unit or other components to the main power until all connections between components are complete.
Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.
Connections
Only PCM signals can be input to the digital (OPTICAL/COAXIAL) jacks of this unit.
A
B
SPEAKERS
NETWORK
COAXIALOPTICAL
FM AM
75Ω
ANTENNA
SUBWOOFER
OUT
TRIGGER
OUT
IN
2
IN
1
IN
OUT
OUT
3
12 12
CD
PHONO
LINE
GND
1 2V 0.1A
O C
Audio
input
Audio
output
Speakers B
Turntable
Audio
output
DVD player, etc.
GND
Audio output
(digital coaxial)
Audio output
(digital optical)
CD player, etc.
Audio
output
CD player, etc.
Subwoofer
CD recorder, etc.
Speakers A
System
connection
11 En
Connections
English
PREPARATION
Note
Do not bundle audio cables and speaker cables together with the
power cable. Doing so may generate noise.
The PHONO jacks are designed for connecting a turntable with
an MM cartridge.
Connect your turntable to the GND terminal to reduce noise in
the signal. However, for some turntables, you may hear less
noise without the GND connection.
If you have a Yamaha subwoofer that supports a system
connection, you can switch the power of the subwoofer in
conjunction with tuning on/off this unit by connecting the
subwoofer to the TRIGGER OUT jack with a monaural mini-
plug cable.
In order to prevent the audio signal from looping when an audio
recording device is connected, the audio signal is not output
from the LINE 2 (OUT) jacks when LINE 2 is selected.
Similarly, the audio signal is not output from the LINE 3 (OUT)
jacks when LINE 3 is selected.
Connecting the speakers
CAUTION
Connect the speakers with impedance as shown below. If you
connect speakers with an excessively low impedance, this unit
may overheat. You can change the speaker impedance setting of
this unit in “SP. IMP” (p. 52) in the ADVANCED SETUP menu.
Connecting speaker cables
Speaker cables have two wires. One is for connecting the
negative (–) terminal of the unit and the speaker, and the
other is for the positive (+) terminal. If the wires are
colored to prevent confusion, connect the black wire to the
negative and the other wire to the positive terminal.
a
Remove approximately 10 mm (3/8”) of insulation from the ends of
the speaker cable and twist the bare wires of the cable firmly together.
b Loosen the speaker terminal.
c Insert the bare wires of the cable into the gap on the side (upper
right or bottom left) of the terminal.
d Tighten the terminal.
Note
When inserting speaker cables into the speaker terminals, insert
only the bare speaker wire. If insulated cable is inserted, the
connection may be poor and sound may not be heard.
Connecting via banana plug
(North America, Australia,
General models only)
Tighten the knob and then insert the banana plug into the
end of the corresponding terminal.
Speaker connection
Speaker impedance (SP IMP.)
4 MIN
8 MIN
(Default)
SPEAKERS A or
SPEAKERS B
4 or higher 8 or higher
SPEAKERS A and
SPEAKERS B
8 or higher 16 or higher
Bi-wire connection 4 or higher 8 or higher
aa
b
b
d
d
c
c
10 mm
(3/8")
Banana plug
12 En
Connections
Bi-wire connection
Bi-wire connection separates the woofer from the
combined midrange and tweeter section. A bi-wire
compatible speaker has four binding post terminals. These
two sets of terminals allow the speaker to be split into two
independent sections. With these connections, the mid and
high frequency drivers are connected to one set of terminals
and the low frequency driver to another set of terminals.
Connect the other speaker to the other set of terminals in
the same way.
Note
When making bi-wire connections, remove the shorting bridges
or cables on the speaker. Refer to the speakers’ instruction
manuals for more information.
To use the bi-wire connections, press SPEAKERS A and
SPEAKERS B on the front panel or on the remote control so
that both “A” and “B” indicators light up on the front display.
A
B
SPEAK
This unit
Speaker
SPEAKERS A/B
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
SLEEP
PHONO
B
A
SPEAKERS
SPEAKERS A/B
13 En
Connections
English
PREPARATION
Connecting the FM/AM antennas
(R-N803)
Connect the supplied FM/AM antenna to this unit.
Fix the end of the FM antenna to a wall, and place the AM
antenna.
Note
If you experience poor reception quality, install an outdoor
antenna.
Unwind only the length of cable needed from the AM antenna
unit.
The wires of the AM antenna have no polarity.
Assembling the supplied AM antenna
Connecting the wires of the AM antenna
Connecting the DAB/FM antenna
(R-N803D)
Connect the supplied DAB/FM antenna to this unit and fix
the antenna ends to a wall.
Note
If you experience poor reception quality, install an outdoor
antenna.
The antenna should be stretched out horizontally.
COAXIALOPTICAL
FM AM
75Ω
ANTENNA
12 12
PHONO GND
FM antenna AM antenna
Insert
2
Hold down
1
COAXIALOPTICAL
FM AM
75Ω
ANTENNA
12 12
PHONO GND
FMDAB
DAB/FM antenna
14 En
Connections
Connecting the network cable
Connect the unit to your router with a commercially-
available STP network cable (CAT-5 or higher straight
cable).
Note
Use an STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference.
Preparing a wireless antenna
If you use a wireless network connection or a Bluetooth
connection, erect the wireless antenna. For information on
how to connect the unit to a wireless network, see
“Connecting to network” (p. 15). For information on using
this unit with a Bluetooth device, see “Playing back music
via Bluetooth” (p. 32).
Notice
Do not apply excessive force on the wireless antenna. Doing so
may damage the antenna.
Connecting the power cord
After all the connections are complete, connect the
supplied power cord to this unit and then to an AC wall
outlet.
WARNING
(General model only)
Before connecting the power cord, make sure you set
VOLTAGE SELECTOR of this unit according to your
local voltage. Improper setting of VOLTAGE SELECTOR
may cause fire and damage to this unit.
Turning on the unit
Press A (power) on the front panel to turn on the unit.
A
SPEAKERS
NETWORK
AC IN
LAN
WAN
Network Attached
Storage
(NAS)
Internet
Modem
Router
Network cable
PC
This unit (rear)
Mobile device
(such as iPhone)
(R-N803)
NETWORK
AC IN
VOLTAGE SELECTOR
11 0
120 V 220
240 V
To the AC wall outlet
with the power cord
A (power)
Connecting to network
15 En
English
PREPARATION
There are several methods to connect the unit to a network. Select a connection method according to your environment.
Note
Some security software installed on your PC or the firewall settings of network devices (such as a router) may block the access of the
unit to the network devices or the Internet. In these cases, configure the security software or firewall settings appropriately.
Each server must be connected to the same subnet as the unit.
To use the service via the Internet, broadband connection is strongly recommended.
When playing a high-resolution audio source via the network, we recommend connecting with a wired router for stable playback.
Connecting with a wireless router (access point)
Connect to the network with the method listed below that corresponds to your environment.
Connecting to network
WAC (Wireless Accessory Configuration)
If you turn on the power to the unit right after you purchase or
initialize it, the unit will automatically use the network settings of the
iOS device (iPhone/iPad/iPod touch) and try to connect to a wireless
LAN (unless the unit is already connected to a wired LAN).
If you have an iOS device, follow the procedure from Step 6 in “Sharing the iOS device setting” (p. 16).
If you plan to connect the unit wirelessly by another method, press RETURN to exit the current screen, and then proceed to one of
the sections below.
R-N803 XXXXXX
WAC
Connecting using the Wi-Fi setting of the iOS
device (iPhone/iPad/iPod touch)
Share the Wi-Fi setting of the iOS
device (p. 16)
Connecting using WPS push button configuration
on the wireless router (or access point)
Use the WPS push button
configuration (p. 17)
Connecting with a wireless router (access point)
without WPS push button configuration
Set the network connection
manually (p. 18)
Connecting using “MusicCast CONTROLLER”
Register this unit to the MusicCast
network and make the wireless
network connection at once (p. 20)
16 En
Connecting to network
Connecting with the wired router
Note
You can configure the network parameters (such as IP address) in “IP Address” (p. 49) in the “Setup” menu.
If you want to use a wired LAN connection when a wireless connection has been made, set “Connection” (p. 48) in the “Setup” menu
to “Wired”.
Connecting without a wired router or wireless router (access point)
Note
When the unit is connected to the network with Wireless Direct, it cannot connect to any other wireless router (access point). To play
back contents from the Internet or update the unit's firmware via the network, connect this unit to a network with a wired router or
wireless router (access point).
Sharing the iOS device setting
You can easily setup a wireless connection by applying the
connection settings on iOS devices (iPhone/iPad/iPod
touch).
Before proceeding, confirm that your iOS device is
connected to a wireless router (access point).
Note
If you set up a wireless connection with this method, all the
network settings will be initialized.
This configuration does not work if the security method of your
wireless router (access point) is WEP. In this case, use other
connection method.
1 Press SETUP.
2 Use the cursor keys (B / C) to select
“Network” and press ENTER.
Note
To return to the previous state, press RETURN.
3 Use the cursor keys (B / C) to select
“Connection” and press ENTER.
4 Use the cursor keys (B / C) to select
“Wireless” and press ENTER.
5 Use the cursor keys (B / C) to select “Share
Setting” and press ENTER twice.
Note
When connected to a wired network, “LAN CABLE” and “Pls
disconnect” appears on the front display. In this case, disconnect
the network cable from the unit, and press ENTER.
Connecting using the DHCP server function of the
router
You can connect to the network by
simply making a wired LAN
connection (p. 14)
Connecting wirelessly to a mobile device
(Wireless Direct)
Connect wirelessly with Wireless
Direct (p. 19)
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Cursor keys
B
/
C
Share Setting
WIRELESS
Wireless(WAC)
SHARE
17 En
Connecting to network
English
PREPARATION
6 On the iOS device, select the unit as the
AirPlay speaker in the Wi-Fi screen.
7 Check the network currently selected and tap
“Next”.
When the sharing process finishes, the unit is
automatically connected to the selected network
(access point).
When the setting finishes, verify whether the unit is
connected to a wireless network (p. 20).
Configuring with the router's WPS
push button
You can easily set up a wireless connection with one push
of the WPS button.
Note
This configuration does not work if the security method of your
wireless router (access point) is WEP or WPA2-TKIP. In this
case, use other connection method.
1 Press SETUP.
2 Use the cursor keys (B / C) to select
“Network” and press ENTER.
Note
To return to the previous state, press RETURN.
3 Use the cursor keys (B / C) to select
“Connection” and press ENTER.
4 Use the cursor keys (B / C) to select
“Wireless” and press ENTER.
5 Press ENTER twice.
“Connecting” appears on the front display.
6 Push the WPS button on the wireless router
(access point).
When the connection process finishes, “Completed”
appears on the front display. When the setting
finishes, verify whether the unit is connected to a
wireless network (p. 20).
If “Not connected” appears, repeat from Step 1 or try
another connection method.
7 To exit from the menu, press SETUP.
The name of this unit
Example (iOS 10)
Tap here to start setup
The network currently
selected
About WPS
WPS (Wi-Fi Protected Setup) is a standard established by the
Wi-Fi Alliance, which allows easy establishment of a
wireless home network.
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Cursor keys
B
/
C
WPS
WIRELESS
18 En
Connecting to network
Set the wireless network connection
manually
Before performing the following procedure, check the
security method and security key on the wireless router
(access point).
1 Press SETUP.
2 Use the cursor keys (B / C) to select
“Network ” and press ENTER.
Note
To return to the previous state, press RETURN.
3 Use the cursor keys (B / C) to select
“Connection” and press ENTER.
4 Use the cursor keys (B / C) to select
“Wireless” and press ENTER.
5 Use the cursor keys (B / C) to select “Manual
Setting” and press ENTER.
6 Use the cursor keys (B / C) to select “SSID”
and press ENTER.
7 Use the cursor keys to enter the SSID on the
wireless router (access point), and press
RETURN to previous state.
Use the cursor keys (D/E) to move the edit position
and the cursor keys (B/C) to select a character.
Press PRESET i to insert a character and PRESET j
to delete.
8 Use the cursor keys (B / C) to select
“Security” and press ENTER.
9 Use the cursor keys (D / E) to select desired
security method and press RETURN.
Settings
None, WEP, WPA2-PSK (AES), Mixed Mode
Note
If you select “None”, the connection may be insecure since the
communication is not encrypted.
10 Use the cursor keys (B / C) to select
“Security Key” and press ENTER.
11 Use the cursor keys to enter the security key
on the wireless router (access point), and
press RETURN to previous state.
If you select “WEP” in step 9, enter either 5 or 13
character string, or 10 or 26 hexadecimal digits.
If you select “WPA2-PSK (AES)” or “Mixed Mode”
in step 9, enter 8 to 63 character string or 64
hexadecimal digits.
Use the cursor keys (D/E) to move the edit position
and the cursor keys (B/C) to select a character.
Press PRESET i to insert a character and PRESET j
to delete.
12 Use the cursor keys (B / C) to select
“Connect[ENTER]” and press ENTER to save
the setting.
If the wireless network connection cannot be made,
the SSID or security key may be incorrect. Repeat
from Step 6.
You can verify whether the unit is connected to a
wireless network (p. 20).
13 To exit from the menu, press SETUP.
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
PRESET j / i
SETUP
ENTER
Cursor keys
B
/
C
/
D
/
E
SSID
MANUAL
SSID
WPA2-PSK(AES)
SECURITY
KEY
19 En
Connecting to network
English
PREPARATION
Connecting a mobile device to the
unit directly (Wireless Direct)
Using Wireless Direct, this unit can operate as a wireless
network access point that mobile devices can directly
connect to.
Note
When making a Wireless Direct connection, you cannot connect
this unit or the mobile device to the Internet, so Internet services
such as Internet radio are not available.
1 Press SETUP.
2 Use the cursor keys (B / C) to select
“Network” and press ENTER.
Note
To return to the previous state, press RETURN.
3 Use the cursor keys (B / C) to select
“Connection” and press ENTER.
4 Use the cursor keys (B / C) to select
“WirelesDirect” and press ENTER.
5 Press ENTER to check the SSID on this unit,
and press RETURN to previous state.
6 Use the cursor keys (B / C) to select
“Security” and press ENTER.
7 Use the cursor keys (D / E) to select desired
security method and press RETURN.
Settings
None, WPA2-PSK (AES)
Note
If you select “None”, proceed to Step 10.
If you select “None”, the connection may be insecure since the
communication is not encrypted.
8 Use the cursor keys (B / C) to select
“Security Key” and press ENTER.
9 Use the cursor keys to enter the security key
on this unit, and press RETURN to previous
state.
Enter 8 to 63 character string or 64 hexadecimal
digits.
Use the cursor keys (D / E) to move the edit position
and the cursor keys (B / C) to select a character.
Press PRESET i to insert a character and PRESET j
to delete.
10 Use the cursor keys (B / C) to select
“Connect[Enter]” and press ENTER to save
the setting.
11 Configure the Wi-Fi settings of a mobile
device.
For details on settings of your mobile device, refer to
the instruction manual of the mobile device.
(1) Enable the Wi-Fi function on the mobile device.
(2) Select the SSID of this unit from the list of
available access points.
(3) When you are prompted for a password, enter the
security key displayed in Step 9.
If the Wireless Direct connection cannot be made, the
security key may be incorrect. Configure the Wi-Fi
settings of a mobile device again.
12 To exit from the menu, press SETUP.
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
PRESET j / i
SETUP
ENTER
Cursor keys
B
/
C
/
D
/
E
SSID
W DIRECT
WPA2-PSK(AES)
SECURITY
KEY
20 En
Connecting to network
Verify the network connection status
Perform the following procedure to verify the unit’s
connection to a network.
1 Press SETUP.
2 Use the cursor keys (B / C) to select
“Network” and press ENTER.
Note
To return to the previous state, press RETURN.
3 Use the cursor keys (B / C) to select
“Information” and press ENTER.
4 Use the cursor keys (B / C) to select
“STATUS”.
When “Connect” appears, the unit is connected to a
network. If “Disconnect” appears, reset connection.
5 To exit from the menu, press SETUP.
Configuring MusicCast
About MusicCast
Use MusicCast to share music between MusicCast-
compatible devices in multiple rooms.
With the dedicated “MusicCast CONTROLLER” app, you
can easily enjoy music from your smartphone, a media
server (a personal computer or NAS) or Internet radio
(streaming services) wherever you are in your home.
All MusicCast-compatible devices can be operated
from the dedicated “MusicCast CONTROLLER” app
Multiple devices that support MusicCast in separate
rooms can be linked to play music simultaneously
Supports music playback through Internet radio
(streaming services)
Network settings for devices that support MusicCast
Visit the following website for more information on
MusicCast and on which devices are compatible.
http://www.yamaha.com/musiccast/
Note
For details on MusicCast, download the MusicCast Setup Guide
from the Yamaha Download website.
http://download.yamaha.com/
MusicCast CONTROLLER
To use network functionality with a device that supports
MusicCast, you need to use the “MusicCast
CONTROLLER” dedicated app for mobile devices.
Search for and install “MusicCast CONTROLLER” (free)
in the App Store or on Google Play.
Registering to the MusicCast network
Register this unit to the MusicCast network.
At the same time, configure the wireless network
connection settings for this unit.
Note
The SSID and security key for your wireless network will
be needed.
1 On your mobile device, start “MusicCast
CONTROLLER” and tap “Setup”.
Note
If you have already connected other MusicCast
compatible devices to the network, tap “” (Settings)
and then “Add New Device”.
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Cursor keys
B
/
C
Connect
STATUS
21 En
Connecting to network
English
PREPARATION
2 Operate “MusicCast CONTROLLER”
following the on screen instructions, then
hold down CONNECT on the front panel of
this unit for 5 seconds.
3 Operate “MusicCast CONTROLLER”
following the onscreen instructions to set up
the network.
This completes the MusicCast network registration and
wireless network connection settings.
Use “MusicCast CONTROLLER” to play back music.
Note
AirPlay and DSD sound cannot be transmitted. Music can be
played back only from this unit.
When Pure Direct (p. 23) is turned on, only the network sources
(such as Internet radio), Bluetooth device sources and USB
storage device sources can be played via the MusicCast
network.
CONNECT
22 En
BASIC OPERATION
Playing a source
1 Press one of the input selection keys to
select the input source you want to listen to.
2 Press SPEAKERS A and/or SPEAKERS B to
select speakers A and/or speakers B.
When speaker set A is turned on, “SPEAKERS
A:On” appears on the front display.
When speaker set B is turned on, “SPEAKERS
B:On” appears on the front display.
Note
When one set of speakers is connected using bi-wire connections,
or when using two sets of speakers simultaneously (A and B),
press SPEAKERS A and SPEAKERS B on the front panel or on
the remote control so that both “A” and “B” indicators light up
on the front display.
When listening with headphones, turn off the speakers.
3 Play the source.
4 Press VOLUME +/– to adjust the sound
output level.
Note
You can adjust the tonal quality by using the BASS, TREBLE,
BALANCE and LOUDNESS controls or the PURE DIRECT
switch on the front panel.
5 When you finish using, press A (power) on
the front panel to turn off the power.
When you press A (power) on the remote control, this
unit set to standby mode.
Switching information on the front
display
When you select a network source or USB as the input
source, you can switch playback information on the front
display.
1 Press DISPLAY.
Each time you press the key, the displayed item
changes.
About 3 seconds later, the corresponding information
for the displayed item appears.
Note
“_” (underscore) will be displayed for characters not supported
by the unit.
Playback
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
TUNING
BAND
SLEEP
PHONO
B
A
SPEAKERS
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
OPTION
Input selection
keys
A (power)
VOLUME
SPEAKERS A/B
Input source Item
Bluetooth
Track (song title), Artist (artist name),
Album (album name)
Server
AirPlay
USB
Track (song title), Artist (artist name),
Album (album name), Time
Net Radio
Track (song title), Album (album name),
Time, Station (station name)
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
DISPLAY
Track
INFO
A
Track #1
SERVER
A
23 En
Playback
English
BASIC
OPERATION
Front panel operations
Enjoying pure high fidelity sound
(Pure Direct)
When the PURE DIRECT switch is turned on, routes
input signals from your audio sources so that the input
signals bypass the BASS, TREBLE, BALANCE and
LOUDNESS controls, thus eliminating any alterations to
the audio signals and creating the purest possible sound.
The PURE DIRECT indicator lights up and the front
display turns off after a few seconds.
Note
When the PURE DIRECT switch is turned on, the front display
turns off.
The BASS, TREBLE, BALANCE, and LOUDNESS controls do
not function while PURE DIRECT is turned on.
Adjusting the BASS and TREBLE
controls
The BASS and TREBLE controls adjust high and low
frequency response.
The center position produces a flat response.
BASS control
When you feel there is not enough bass (low frequency
sound), rotate clockwise to boost. When you feel there is
too much bass, rotate counterclockwise to suppress.
Control range: –10 dB to +10 dB (20 Hz)
TREBLE control
When you feel there is not enough treble (high frequency
sound), rotate clockwise to boost. When you feel there is
too much treble, rotate counterclockwise to suppress.
Control range: –10 dB to +10 dB (20 kHz)
Adjusting the BALANCE control
The BALANCE control adjusts the sound output balance
of the left and right speakers to compensate for sound
imbalance caused by speaker locations or listening room
conditions.
Note
If you rotate the BALANCE control to the end of L (left) or R
(right), the opposite side of channel is muted.
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
PURE DIRECT switch
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
BASS TREBLE
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
BALANCE
24 En
Playback
Adjusting the LOUDNESS control
Retain a full tonal range at any volume level, thus
compensating for the human ears’ loss of sensitivity to
high and low-frequency ranges at low volume.
Note
The LOUDNESS control does not function when the YPAO
Volume function (p. 50) is enabled.
CAUTION
If the PURE DIRECT switch is turned on with the LOUDNESS
control set at a certain level, the input signals bypass the
LOUDNESS control, resulting in a sudden increase in the sound
output level. To prevent your ears or the speakers from being
damaged, be sure to press the PURE DIRECT switch after
lowering the sound output level or after checking that the
LOUDNESS control is properly set.
1 Set the LOUDNESS control to the FLAT
position.
2 Rotate the VOLUME control on the front
panel (or press VOLUME +/– on the remote
control) to set the sound output level to the
loudest listening level that you would listen
to.
3 Rotate the LOUDNESS control until the
desired volume is obtained.
Note
After setting the LOUDNESS control, enjoy listening to music at
your preferred volume level. If the effect of the LOUDNESS
control setting is too strong or weak, readjust the LOUDNESS
control.
Using the sleep timer
Use this feature to automatically set this unit to standby
mode after a certain amount of time. The sleep timer is
useful when you are going to sleep while this unit is
playing or recording a source.
Note
The sleep timer can only be set with the remote control.
1 Press SLEEP repeatedly to set the amount of
time before this unit is set to standby mode.
Each time you press SLEEP, the front display
changes as shown below.
The SLEEP indicator blinks while setting the amount
of time for the sleep timer.
If the sleep timer is set, the SLEEP indicator on the
front display lights up.
Note
To disable the sleep timer, select “Sleep Off”.
The sleep timer setting can also be canceled by pressing
A (power) to set this unit to standby mode.
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
VOLUMELOUDNESS
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
LINE 2 LINE 3
SLEEP
PHONO
B
A
SPEAKERS
A
SLEEP
(power)
Sleep 120 min.
Sleep Off Sleep 30 min. Sleep 60 min.
Sleep 90 min.
Sleep 120min.
SLEEP
VOL.
A
Listening to FM/AM radio
25 En
English
BASIC
OPERATION
Note
R-N803D does not include an AM tuner.
FM/AM tuning
1 Press TUNER to select “TUNER” as the input
source.
2 Press BAND repeatedly to select the
reception band (FM or AM).
3 Press TUNING jj / ii to set a frequency.
To search stations automatically, press and hold
TUNING jj / ii for a second.
If a broadcast is being received, “TUNED” indicator
on the front display will be lit. If a stereo broadcast is
being received, the “STEREO” indicator will also lit.
Note
If the station signals are weak, tuning search does not stop at the
desired station.
When FM radio reception is unstable, switching the FM mode
to "Mono" may improve it.
Improving FM reception (FM mode)
If the signal from the station is weak and the sound quality
is not good, set the FM band reception mode to monaural
mode to improve reception.
1 Press MODE repeatedly to select “Stereo”
(automatic stereo mode) or “Mono”
(monaural mode) when this unit is tuned in to
an FM radio station.
When “Mono” is selected, FM broadcasts will be
heard in monaural sound.
Note
The STEREO indicator on the front panel lights up while
listening to a station in stereo mode.
Registering favorite radio stations
(presets)
You can register up to 40 radio stations as presets. Once
you have registered stations, you can easily tune into them
by selecting their preset numbers.
You can automatically register FM radio stations that have
strong signals (auto preset). For AM radio stations or FM
radio stations with weak signals, register them manually
(p. 26).
Registering FM radio stations
automatically (auto preset)
Note
When you register radio stations automatically, radio stations
currently registered to preset numbers may be overwritten.
If the station you want to register is weak in signal strength, try
using the manual preset tuning method.
FM stations registered as presets using the automatic preset
registration feature will be heard in stereo.
(U.K. and Europe models only)
Only Radio Data System broadcasting stations can be preset
automatically.
Listening to FM/AM radio
TUNING jj / ii
TUNER
BAND
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SLEEP
PHONO
B
A
SPEAKERS
FM 98.50MHz
VOL.
TUNEDSTEREO
A
Frequency
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
MODE
26 En
Listening to FM/AM radio
1 Press TUNER to select “TUNER” as the input
source.
2 Press OPTION on the remote control.
The “Option” menu is displayed (p. 46).
3 Use the cursor keys (B / C) to select “Auto
Preset”, and then press ENTER.
This unit starts scanning the FM band about 5
seconds later from the lowest frequency upwards.
To begin scanning immediately, hold down ENTER.
Note
Before scanning begins, you can specify the first preset number
to be used by pressing PRESET j / i or cursor key (B/C) on the
remote control.
To cancel scanning, press BAND or RETURN.
When scanning is complete, “FINISH” is displayed and
then the display returns to original state.
Registering a radio station manually
1 Follow “FM/AM tuning” (p.25) to tune into the
desired radio station.
2
Press MEMORY.
Note
By holding down MEMORY for more than 3 seconds, you can
skip the following steps and automatically register the selected
station to an empty preset number (i.e., the preset number
following the last preset number used).
3 PRESET j / i
to select the preset number to
which the station will be registered.
If you select a preset number to which no station is
registered, the message “Empty” is displayed.
4
Press MEMORY.
When registration is complete, the display returns to
the original state.
Note
To cancel registration, press RETURN.
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
PRESET j / i
RETURN
OPTION
TUNER
BAND
ENTER
Cursor keys
B
/
C
Auto Preset
VOL.
OPTION
A
01:FM 87.5 MHz
VOL.
READY
A
Preset number Frequency
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
VOLUME
RETURN
ENTER
OPTION
PRESET j / i
RETURN
MEMORY
02:Empty
VOL.
9850
TUNEDSTEREO
A
“Empty” (not in use) or the frequency currently registered
27 En
Listening to FM/AM radio
English
BASIC
OPERATION
Recalling a preset station
You can recall preset stations that were registered using
automatic station preset or manual station preset.
1 Press TUNER to select “TUNER” as the input
source.
2 Press PRESET j / i to select a preset
number.
Note
Preset numbers to which no stations are registered are skipped.
“No Presets” is displayed if no stations are registered.
Clearing a preset station
Clear radio stations registered to the preset numbers.
On the remote control
1 Press TUNER to select “TUNER” as the input
source.
2 Press OPTION.
3 Use the cursor keys to select “Clear Preset”
and press ENTER.
4 Use the cursor keys (B / C) to select a preset
station to be cleared and press ENTER.
If the preset station is cleared, “Cleared” appears and
then the next in-use preset number is displayed.
5 Repeat step 4 until all desired preset stations
are cleared.
6 To exit from the “Option” menu, press
OPTION.
On the front panel
1 Rotate the INPUT selector to select “TUNER”
as the input source.
2 Press CLEAR.
3 Press PRESET j / i to select a preset station
to be cleared and press CLEAR.
If the preset station is cleared, “Cleared” appears.
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SLEEP
PHONO
B
A
SPEAKERS
TUNER
PRESET j / i
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
OPTION
ENTER
TUNER
Cursor keys
B
/
C
Clear Preset
VOL.
OPTION
A
01:FM 98.50MHz
VOL.
CLEAR
TUNEDSTEREO
AA
Preset station to be cleared
01:Cleard
VOL.
CLEAR
AA
INPUT CLEAR PRESET j / i SELECT/
ENTER
01:FM 98.50MHz
VOL.
CLEAR
TUNEDSTEREO
AA
Preset station to be cleared
01:Cleard
VOL.
CLEAR
AA
28 En
Listening to FM/AM radio
Radio Data System tuning
(U.K. and Europe models only)
Radio Data System is a data transmission system used by
FM stations in many countries. The unit can receive
various types of Radio Data System data, such as
“Program Service”, “Program Type,” “Radio Text” and
“Clock Time”, when it is tuned into a Radio Data System
broadcasting station.
Displaying the Radio Data System
information
1 Tune into the desired Radio Data System
broadcasting station.
Note
We recommend using “Auto Preset” to tune into the Radio Data
System broadcasting stations (p. 25).
2 Press DISPLAY.
Each time you press the key, the displayed item changes.
About 3 seconds later, the corresponding information
for the displayed item appears.
Note
“Program Service”, “Program Type”, “Radio Text”, and “Clock
Time” are not displayed if the radio station does not provide the
Radio Data System service.
Program Service Program service name
Program Type Current program type
Radio Text Information on the current program
Clock Time Current time
Frequency Frequency
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
DISPLAY
Program Type
INFO
VOL.
TUNEDSTEREO
A
Item name
CLASSICS
VOL.
,9850
TUNEDSTEREO
A
Information
Listening to DAB radio (R-N803D)
29 En
English
BASIC
OPERATION
DAB (Digital Audio Broadcasting) uses digital signals for
clearer sound and more stable reception compared to
analog signals. This unit can also receive DAB+ (an
upgraded version of DAB) that allows for more stations
using MPEG-4 audio codec (AAC+), which has a more
efficient transmission method.
Note
This unit supports Band III (174 to 240 MHz) only.
Preparing the DAB tuning
Before tuning in to DAB stations, an initial scan must be
performed. When you select the DAB for the first time,
the initial scan is performed automatically.
To listen to a DAB station, connect the antenna as
described in “Connecting the DAB/FM antenna (R-
N803D)” (p.13).
1 Press TUNER to select “TUNER” as the input
source.
2 Press BAND to select the DAB band.
The initial scan starts. During the scan, the progress is
displayed on the front display.
When the scan is complete, the top of the list of the
scanned stations appears on the front display.
Note
If no DAB radio stations are found by an initial scan, “Not
Found” appears on the front display, followed by “Off Air”.
Press BAND twice to re-select the DAB band and scan again.
You can check reception strength of each DAB channel label (p.
31).
To perform an initial scan again after some DAB radio stations
are stored, select “Initiate Scan” (p.46) in the “OPTION” menu.
If you perform an initial scan again, the DAB radio stations
currently registered to the preset numbers will be cleared.
Selecting a DAB radio station for
reception
You can select a DAB radio station from the stations
stored by the initial scan.
1 Press TUNER to select “TUNER” as the input
source.
2 Press BAND to select the DAB band.
3 Press TUNING jj / ii to select a DAB radio
station.
Note
“Off Air” appears when the selected DAB radio station is
currently not available.
When the unit is receiving a secondary station, “2” appears next
to “DAB”.
Listening to DAB radio (R-N803D)
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
ENTER
TUNER
BAND
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
ENTER
TUNING jj / ii
TUNER
BAND
BBC Radio 4
VOL.
DAB
A
30 En
Listening to DAB radio (R-N803D)
Using preset function
You can register up to 40 DAB radio stations as presets.
Once you have registered stations, you can easily tune in
to them by recalling the presets.
Note
You can register up to 40 favorite radio stations each for DAB
and FM bands.
Registering a DAB radio station
Select a DAB radio station and register it to a preset
number.
1 Follow “Selecting a DAB radio station for
reception” (p.29) to tune into the desired
DAB radio station.
2 Press MEMORY.
Note
By holding down MEMORY for more than 3 seconds, you can
skip the following steps and automatically register the selected
station to an empty preset number (i.e., the preset number
following the last preset number used).
3 Press PRESET j / i to select the preset
number to which the station will be
registered.
If you select a preset number to which no station is
registered, “Empty” is displayed.
If you select a preset number to which a station has
already been registered, “Overwrite?” is displayed.
4 Press MEMORY.
When registration is complete, the display returns to the
original state.
Note
To cancel registration, press RETURN or do not perform any
operations for about 30 seconds.
Recalling a preset station
Tune into a registered DAB radio station by selecting its
preset number.
1 Press TUNER to select “TUNER” as the input
source.
2 Press BAND to select the DAB band.
3 Press PRESET j / i to select the desired DAB
radio station.
Note
Preset numbers to which no stations are registered are skipped.
If this unit does not have any preset stations, “No Presets” is
displayed.
Clearing preset DAB radio stations
Clear DAB radio stations registered to the preset numbers.
1 Press TUNER to select “TUNER” as the input
source.
2 Press BAND to select the DAB band.
3 Press OPTION.
4 Use the cursor keys (B / C) to select “Clear
Preset” and press ENTER.
5 Use the cursor keys (B / C) to select a preset
DAB radio station to be cleared and press
ENTER.
If the preset DAB radio station is cleared “Cleared”
appears and the next in-use preset number is
displayed.
6 Repeat step 5 until all desired preset DAB
radio stations are cleared.
7 To exit from the “OPTION” menu, press
OPTION.
NET USB
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
VOLUME
RETURN
ENTER
OPTION
PRESET j / i
OPTION
RETURN
TUNER
BAND
MEMORY
ENTER
Cursor keys
B
/
C
02:Empty
VOL.
MEMORY
A
“Empty” (not in use) or “Overwrite?” (in use)
PRESET:01
VOL.
A
31 En
Listening to DAB radio (R-N803D)
English
BASIC
OPERATION
Displaying the DAB information
This unit can receive various types of DAB information
when it is tuned in to a DAB radio station.
1 Select “TUNER” as the input source and tune
into the desired DAB radio station.
2 Press DISPLAY on the front panel.
Each time you press the key, the displayed item
changes.
About 3 seconds later, the corresponding information
appears.
Note
Some information may not be available depending on the selected
DAB radio station.
Checking reception strength of each
DAB channel label
You can check reception strength of each DAB channel
label (0 [none] to 100 [best]).
1 Press TUNER to select “TUNER” as the input
source.
2 Press BAND to select the DAB band.
3 Press OPTION.
4 Use the cursor keys (B / C) to select “Tune
Aid” and press ENTER.
5 Use the cursor keys (B / C) to select the
desired DAB channel label.
6 To exit from the “OPTION” menu, press
OPTION.
Item Information
Service Label Station name
DLS
(Dynamic Label Segment)
Information on the station
Ensemble Label Ensemble name
Program Type Station genre
Date and Time Current date and time
Audio Mode Audio mode (monaural/stereo)
and bit rate
CH Label/Freq Channel label and frequency
Signal Quality Signal reception quality (0 [none]
to 100 [best])
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
DISPLAY
Program Type
DAB
Item name
SPORT
DAB
Information
NET USB
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
VOLUME
RETURN
ENTER
OPTION
OPTION
TUNER
BAND
ENTER
Cursor keys
B
/
C
12B Level: 80
TUNE AID
DAB channel label Reception strength
32 En
You can play back music files stored on a Bluetooth
device (such as mobile device) on the unit.
Please also refer to the owners manual of your Bluetooth
device.
Note
To use the Bluetooth function, set “Bluetooth” (p. 50) in the
“Setup” menu to “On” (Default).
•A Bluetooth device may not be detected by the unit or some
feature may not be compatible, depending on the model.
You can transmit audio to Bluetooth speakers or headphones
using “MusicCast CONTROLLER” (p. 20). The audio output
can only be selected from “MusicCast CONTROLLER”.
Connecting a Bluetooth device
(pairing)
When connecting a Bluetooth device to the unit for the
first time, the pairing operation is required to perform.
Pairing is an operation that registers the Bluetooth devices
with each other beforehand. Once pairing has been
completed, subsequent reconnection will be easy even
after the Bluetooth connection is disconnected.
1 Press BLUETOOTH to select “Bluetooth” as
the input source.
If another Bluetooth device is already connected,
disconnect the Bluetooth connection before you
perform a pairing operation.
2 Turn on the Bluetooth function of the
Bluetooth device.
3 On the Bluetooth device, select the unit
(network name) from the available device list.
After pairing has been completed and the unit is
connected to the Bluetooth device, “Connected”
appears on the front display, and Bluetooth indicator
will be light up.
Note
If the pass key is required, enter the number “0000”.
You can change the network name of this unit in “Network
Name” (p.49) in the “Setup” menu.
Playing back Bluetooth device
contents
Connect a paired Bluetooth device and start playback.
Check the following beforehand:
Pairing has been completed.
Bluetooth function on the Bluetooth device is turned on.
1 Press BLUETOOTH to select “Bluetooth” as
the input source.
Note
If the unit detects the Bluetooth device previously connected, the
unit automatically connects to the Bluetooth device after Step 1.
To establish another Bluetooth connection, first disconnect the
current Bluetooth connection.
Playing back music via Bluetooth
This unit Bluetooth device
(such as mobile device)
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
SLEEP
PHONO
B
A
SPEAKERS
BLUETOOTH
Connected
VOL.
BLUETOOTH
A
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
SLEEP
PHONO
B
A
SPEAKERS
REPEAT
SHUFFLE
Playback keys
BLUETOOTH
33 En
Playing back music via Bluetooth
English
BASIC
OPERATION
2 Operate the Bluetooth device to establish a
Bluetooth connection.
Select the unit’s model name from the Bluetooth
device list on your device.
When a connection is established, Bluetooth indicator
on the front display will be light up.
Note
If you cannot connect the Bluetooth device, please perform
pairing again.
3 Operate the Bluetooth device to play back
music.
Note
You can use the playback keys on the remote control to control
playback.
Disconnecting a Bluetooth
connection
Follow one of the procedures below to disconnect a
Bluetooth connection.
Turn off the Bluetooth function on the Bluetooth
device.
Hold down BLUETOOTH on the remote control for at
least 3 seconds.
Select an input source other than “Bluetooth” on the
unit.
Bluetooth
Bluetooth is a technology for wireless communication
between devices within an area of about 10 meters (33 ft)
employing the 2.4 GHz frequency band, a band which can
be used without a license.
Handling Bluetooth communications
The 2.4 GHz band used by Bluetooth compatible devices is
a radio band shared by many types of equipment. While
Bluetooth compatible devices use a technology minimizing
the influence of other components using the same radio
band, such influence may reduce the speed or distance of
communications and in some cases interrupt
communications.
The speed of signal transfer and the distance at which
communication is possible differs according to the distance
between the communicating devices, the presence of
obstacles, radio wave conditions and the type of equipment.
Yamaha does not guarantee all wireless connections
between this unit and devices compatible with Bluetooth
function.
34 En
You can play back music files stored on your PC or
DLNA-compatible NAS on the unit.
Note
To use this function, the unit and your PC/NAS must be
connected to the same router (p. 14). You can check whether the
network parameters (such as the IP address) are properly
assigned to the unit in “Information” (p.48) in the “Setup”
menu.
To play back music files, the server software installed on the
PC/NAS must support the music file formats that you want to
play back.
The audio may be interrupted while using the wireless network
connection. In this case, use the wired network connection.
You can connect up to 16 media servers to this unit.
For details on supported file formats, see “Supported file
formats” (p.62).
Setting the media sharing of music
files
To play back music files in your computer with this unit,
you need to make the media sharing setting between the
unit and computer (Windows Media Player 12 or later). In
here, setting with Windows Media Player in Windows 7 is
taken as an example.
When using Windows Media Player 12
1 Start Windows Media Player 12 on your PC.
2 Select “Stream”, then “Turn on media
streaming...”.
The control panel window of your PC appears.
3 Click “Turn on media streaming”.
4 Select “Allowed” from the drop-down list
next to the unit’s model name.
5 As with Step 4, select “Allowed” from the
drop-down list next to devices (PCs or
mobile devices) which you want to use as the
media controllers.
6 Click “OK” to exit.
When using a PC or a NAS with other
DLNA server software installed
Refer to the instruction manual for the device or software
and configure the media sharing settings.
Playing back music stored on media servers (PCs/NAS)
PC
NAS
This unit
(Example of English version)
R-N803
35 En
Playing back music stored on media servers (PCs/NAS)
English
BASIC
OPERATION
Playback of PC music contents
Follow the procedure below to operate the PC music
contents and start playback.
Note
“_” (underscore) will be displayed for characters not supported
by the unit.
1 Press NET repeatedly to select “Server” as
the input source.
2 Use the cursor keys (B / C) to select a music
server and press ENTER.
3 Use the cursor keys to select an item and
press ENTER.
If a song is selected, playback starts and the playback
information is displayed.
Note
If playback of a music file selected from the unit is ongoing on
your PC, the playback information is displayed.
You can register the current playback song as a preset (p. 41).
If you press the DISPLAY on the front panel repeatedly, you
can switch the playback information on the front display (p. 22).
Use the following remote control keys to control
playback.
Note
You can also use a DLNA-compatible Digital Media Controller
(DMC) to control playback. For details, see “DMC Control”
(p.49).
Repeat/shuffle settings
You can configure the repeat/shuffle settings for the
playback of PC music content.
1 When the input source is Server,” press
REPEAT or SHUFFLE on the playback key
repeatedly to select the playback method.
NET USB
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
OPTION
RETURN
OPTION
NOW PLAYING
HOME
ENTER
NET
Playback keys
Cursor keys
B / C / D / E
NAS A
SERVER
A
Song A
SERVER
A
Keys Function
Cursor keys
Select a music file or folder.
ENTER
Starts playback if pressed while
content is selected. Moves down
one level if pressed while a folder
is selected.
RETURN
Moves up one level.
Playback
keys
p/ e
Pauses/resumes playback.
s
Stops playback.
b / w
Skips forward/backward.
f / a
HOME
Displays the root directory of the
music server.
NOW PLAYING
Displays information about the
song thats playing.
Playback
keys
Setting Function
REPEAT
Off Turns off the repeat function.
One
Plays back the current song
repeatedly.
All
Plays back all songs in the current
album (folder) repeatedly.
SHUFFLE
Off Turns off the shuffle function.
On
Plays back songs in the current album
(folder) in random order.
36 En
Playing back music stored on media servers (PCs/NAS)
Automatic playback setting
Use this setting to choose whether to automatically play
back music from your PC or from the NAS when turning
on the unit or when selecting “Server” as the input source.
1 When the input source is “Server”, press
OPTION.
2 Use the cursor keys (B / C) to select “Auto
Playback” and press ENTER.
3 Use the cursor keys (D / E) to select “On”
(enable) or “Off” (disable).
4 To exit from the menu, press OPTION.
Listening to Internet radio
37 En
English
BASIC
OPERATION
You can listen to Internet radio stations from all over the
world.
Note
To use this function, the unit must be connected to the Internet
(p. 14). You can check whether the network parameters (such as
the IP address) are properly assigned to the unit in
“Information” (p.48) in the “Setup” menu.
You may not be able to receive some Internet radio stations.
This unit uses the airable.Radio service. airable is a service of
Tune In GmbH.
This service may be discontinued without notice.
1 Press NET repeatedly to select “Net Radio”
as the input source.
The station list appears on the front display.
2 Use the cursor keys to select an item and
press ENTER.
If an Internet radio station is selected, playback starts
and the playback information is displayed.
Use the following remote control keys to control
playback.
Note
You can register the current playback station as a preset (p. 41).
If you press the DISPLAY on the front panel repeatedly, you
can switch the playback information on the front display (p. 22).
Some information may not be available depending on the
station.
Listening to Internet radio
NET USB
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
OPTION
RETURN
NOW PLAYING
HOME
ENTER
NET
Cursor keys
B / C / D / E
Playback keys
Radios
NET RADIO
A
Keys Function
Cursor keys
Select the Internet radio station or
category such as the genre.
ENTER
Starts playback if pressed while
an Internet radio station is
selected. Moves down one level if
pressed while a category is
selected.
RETURN
Moves up one level.
Playback keys s
Stops playback.
HOME
Displays the top categories if
pressed during playback.
NOW PLAYING
Displays the playback
information for the Internet radio
station.
JazzST
NET RADIO
A
38 En
The AirPlay function allows you to play back iPhone/
iTunes music on the unit via network.
Note
To use this function, the unit and your PC or iPhone must be
connected to the same router (p. 14).
Playback of iPhone/iTunes music
contents
Follow the procedure below to play back iPhone/iTunes
music contents on the unit.
1 Turn on the unit, and start iTunes on the PC
or display the playback screen on the
iPhone.
If the iPhone/iTunes recognizes the unit, the AirPlay
icon appears.
Note
If the icon does not appear, check whether the unit and PC/iPhone
are connected to the router properly.
2 On the iPhone/iTunes, click (tap) the AirPlay
icon and select the unit (network name of the
unit) as the audio output device.
3 Select a song and start playback.
The unit automatically selects “AirPlay” as the input
source and starts playback. The playback information is
displayed on the front display.
Note
If you press the DISPLAY on the front panel repeatedly, you
can switch the playback information on the front display (p. 22).
You can turn on the unit automatically when starting playback
on iTunes or iPhone by setting “Standby (Network Standby)”
(p.49) in the “Setup” menu to “On”.
You can edit the network name (the unit’s name on the network)
displayed on iPhone/iTunes in “Network Name” (p.49) in the
“Setup” menu.
You can adjust the unit’s volume from the iPhone/iTunes during
playback.
CAUTION
Adjusting the volume on iTunes or iPhone may make the volume
unexpectedly loud, which could result in damage to your hearing
or to the device. If the playback volume is too loud, stop playback
immediately on iTunes or iPhone. We recommend using “Volume
interlock” (p. 46) in the “Option” menu to limit the changes in
volume from iTunes or iPhone.
Use the following remote control keys to control playback.
Playing back iPhone/iTunes music via a network (AirPlay)
AirPlay works with iPhone, iPad, and iPod touch with iOS
4.3.3 or later, Mac with OS X Mountain Lion or later, and
Mac and PC with iTunes 10.2.2 or later.
(as of June 2017)
PC
iTunes
Router
Playback starts
iPhone
Starts playback
on iTunes
or iPhone
This unit
iTunes (example)iOS10 (example)
Keys Functions
Playback
keys
p/ e
Pauses/resumes playback.
s
Stops playback.
b / w
Skips forward/backward.
f / a
REPEAT Changes the Repeat settings.
SHUFFLE Changes the Shuffle settings.
Playing back music stored on a USB storage device
39 En
English
BASIC
OPERATION
You can play back music files stored on a USB storage device on the unit. Refer to the instruction manuals for the USB
storage device for more information.
Note
Do not connect devices other than USB mass storage class devices (such as USB chargers or USB hubs), PCs, card readers, an
external HDD, etc.
Some features may not be compatible, depending on the model or manufacturer of the USB storage device.
For details on supported USB storage devices and file formats, see “Supported devices and file formats” (p.62).
Connecting a USB storage device
1 Connect the USB storage device to the USB
jack.
Note
If the USB storage device contains many files, it may take time
to load the them. In this case, “Loading...” appears in the front
display.
Disconnect the USB storage device from the USB jack when it
is not in use.
Stop playback of the USB storage device before disconnect it
from the USB jack.
You cannot connect the PC to the USB jack of the unit.
This unit cannot charge USB storage devices while it is in
standby mode.
Playback of USB storage device contents
Follow the procedure below to operate the USB storage
device contents and start playback.
Note
“_” (underscore) will be displayed for characters not supported
by the unit.
1
Press USB to select “USB” as the input source.
2 Use the cursor keys to select an item and
press ENTER.
If a song is selected, playback starts and the playback
information is displayed.
Note
You can register the current playback song as a preset (p. 41).
If you press the DISPLAY on the front panel repeatedly, you
can switch the playback information on the front display (p. 22).
Playing back music stored on a USB storage device
BASSINPUT
5V
1A
PHONES
YPAO MIC
SPEAKERS USB
AB
This unit (front)
USB storage device
Connected
USB
VOL.
A
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
REPEAT
SHUFFLE
OPTION
RETURN
OPTION
USB
NOW PLAYING
HOME
ENTER
Playback keys
Cursor keys
B / C / D / E
Blues
USB
VOL.
A
Track #3
USB
VOL.
A
40 En
Playing back music stored on a USB storage device
Use the following remote control keys to control playback.
Repeat/shuffle settings
You can configure the repeat/shuffle settings for playback
of USB storage device contents.
1 If the input source is “USB,” press REPEAT
or SHUFFLE on the playback keys repeatedly
to select the playback method.
Automatic playback setting
Use this setting to choose whether to automatically play
back music from your USB storage device when turning
on the unit or when selecting “USB” as the input source.
1 When the input source is “USB”, press
OPTION.
2 Use the cursor keys (B / C) to select “Auto
Playback” and press ENTER.
3 Use the cursor keys (D / E) to select “On”
(enable) or “Off” (disable).
4 To exit from the menu, press OPTION.
Keys Function
Cursor keys
Select a music file or folder.
ENTER
Starts playback if pressed while a
music file is selected. Moves down
one level if pressed while a folder is
selected.
RETURN
Moves up one level.
Playback
keys
p/ e
Pauses/resumes playback.
s
Stops playback.
b / w
Skips forward/backward.
f / a
HOME
Displays the root directory of the
USB device.
NOW PLAYING
Displays information about the
song that’s playing.
Playback
keys
Setting Function
REPEAT
Off Turns off the repeat function.
One
Plays back the current song
repeatedly.
All
Plays back all songs in the current
album (folder) repeatedly.
SHUFFLE
Off Turns off the shuffle function.
On
Plays back songs in the current album
(folder) in random order.
Registering the current playback song/station (Preset function)
41 En
English
BASIC
OPERATION
When you select network sources and USB as the input
source, you can register the current playback song or
streaming station as a preset up to 40.
You can then easily recall any preset song/station by
selecting its preset number.
The following input sources can be set as presets.
Server, Net Radio, USB and streaming services.
Note
You can also register songs and stations as presets using
“MusicCast CONTROLLER” (p.20).
When you register music files stored on a USB storage device
or a PC/NAS, this unit memorizes the relative position of the
music files in the folder. If you have added or deleted any music
files to or from the folder, this unit may not recall the music file
correctly. In such cases, register the items again.
Registering to a preset
1 Playback a song or streaming station you
want to register.
2 Press MEMORY.
Note
By holding down MEMORY for more than 3 seconds, you can
skip the following steps and automatically register the selected
song/station to an empty preset number (i.e., the preset number
following the last preset number used).
3 PRESET j / i to select the preset number to
which the song/station will be registered.
If you select a preset number to which no station is
registered, the message “Empty” is displayed.
4 Press MEMORY.
When registration is complete, the display returns to
the original state.
Note
To cancel registration, press RETURN.
Recalling a preset
1 Press NET or USB to select the desired input
source.
2 Press PRESET j / i to select a preset
number.
3 Press ENTER to recall preset.
Note
It may take a while to recall a preset song or a preset station.
To cancel recalling, press RETURN.
You can also recall preset songs or preset stations using
“MusicCast CONTROLLER” (p.20).
Clearing a preset
1 Press NET or USB to select the desired input
source.
2 Press PRESET j / i to select a preset number
to be cleared.
3 Press CLEAR on the front panel to clear the
preset.
If the preset content is cleared, “Empty” appears.
Registering the current playback song/station (Preset function)
LINE 1
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
ENTER
PRESET j / i
USB
NET
MEMORY
ENTER
42 En
ADVANCED OPERATION
The Yamaha Parametric room Acoustic Optimizer
(YPAO) function detects speaker connections, measures
the distances from them to your listening position, and
then automatically optimizes the speaker settings, such as
volume balance and acoustic parameters, to suit your
room.
Note
The YPAO function of this unit adopts the YPAO-R.S.C.
(Reflected Sound Control) technology that enables to create
natural sound fields like a room specifically designed for
acoustic perfection.
Note the following regarding YPAO measurement.
Test tones are output at high volume and may surprise or
frighten small children.
Test tone volume cannot be adjusted.
Keep the room as quiet as possible.
Stay in a corner of the room behind the listening position so
that you do not become an obstacle between speakers and the
YPAO microphone.
Do not connect headphones.
1 Press A (power) on the front panel to turn on
this unit.
2 Turn on the subwoofer and set the volume to
half.
If the crossover frequency is adjustable, set it to
maximum.
3 Configure the following settings.
Press SPEAKERS A/B on the front panel or
remote control to select the speakers to be used.
Set the BASS control and TREBLE control on the
front panel to 0 (center position).
Set the BALANCE control on the front panel to the
center position.
Set the LOUDNESS control on the front panel to
FLAT (center position).
If Pure Direct is turned on, press PURE DIRECT
on the front panel to turn it off.
Note
The speaker settings are individually saved depending on the
speaker system (A, B, A+B).
When using YPAO, select the speaker system (A+B) only for
the bi-wire connection. If you select the speaker system (A+B)
when connecting other speakers to the SPEAKERS A/B
terminals, the measurement will not be performed properly.
Optimizing the speaker settings automatically (YPAO)
LINE 1
OPT 1 OPT 2 CD
COAX 1 COAX 2
BLUETOOTH
NET USB
LINE 2 LINE 3
TUNER
PRESET
TUNING
BAND
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
SLEEP
PHONO
B
A
SPEAKERS
OPTION
RETURN
ENTER
SPEAKERS A/B
Cursor keys
B
/
C
/
D
/
E
VOLUME HIGH CUT
CROSSOVER/
MIN MAXMIN MAX
BASS TREBLE BALANCE LOUDNESS
PURE DIRECTSPEAKERS A/B
43 En
Optimizing the speaker settings automatically (YPAO)
English
ADVANCED
OPERATION
4 Place the YPAO microphone at your listening
position and connect it to the YPAO MIC jack
on the front panel.
Note
Place the YPAO microphone at your listening position (same
height as your ears). We recommend the use of a tripod as a
microphone stand. You can use the tripod screws to stabilize the
microphone.
The following message appears on the front display.
Note
To cancel the operation, disconnect the YPAO microphone before
starting the measurement.
5 To start the measurement, press ENTER.
The measurement will start in 10 seconds. It takes
about 1 minute to perform the measurement.
Note
To cancel the measurement, press RETURN and then follow the
procedure in “Error messages” (p. 44).
“Result Info.” appears on the front display when the
measurement finishes.
Note
If “Error Info” appears, press the cursor key (E) to check the
error message (p. 44).
6 To check the measurement result, press the
cursor key (E).
If “No Warning” appears on the front display, the
measurement is properly completed.
Note
If any warning message (such as W-1) appears on the front
display, see “Warning messages” (p. 45).
7 Press the cursor key (D) or RETURN.
8 To save the measurement results, use the
cursor keys (B / C) to select “Save” and
press ENTER.
To finish the measurement without saving
the result, use the cursor keys (B / C) to
select “Cancel” and press ENTER.
Note
You can change the YPAO settings (YPAO On/Off and YPAO
Volume) in the “Setup” menu (p. 50).
9 Disconnect the YPAO microphone from this
unit.
Notice
The YPAO microphone is sensitive to heat, so should not be
placed anywhere where it could be exposed to direct sunlight or
high temperatures (such as on top of AV equipment).
YPAO MIC
YPAO MIC jack
YPAO microphone at
listening position
Ear
height
[ENTER]:Start
YPAO
Result Info.
YPAO
(
A
No Warning
YPAO
(
A
[ENTER]:Save
YPAO
(
A
[ENTER]:Cancel
YPAO
(
A
Disconnect MIC
YPAO
(
A
44 En
Optimizing the speaker settings automatically (YPAO)
Error messages
If any error message is displayed during the measurement, resolve the problem and perform YPAO again.
Note
After checking the error message, press the cursor key (D) to return to the previous state and follow the procedure below,
To start the measurement again:
Use the cursor keys (
B / C) to select “Retry” and press ENTER. Proceed to Step 5 in page 43.
To exit YPAO:
Use the cursor keys (
B / C) to select “Exit” and press ENTER.
Error message Cause Remedy
E-1 Noisy The noise is too loud.
Keep the room quiet and start the measurement
again.
E-2 No Signal The YPAO microphone cannot detect test tones.
Connect the YPAO microphone to the YPAO
MIC jack firmly and start the measurement
again. If this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or service
center.
E-3 No MIC The YPAO microphone has been removed.
Connect the YPAO microphone to the YPAO
MIC jack firmly and start the measurement
again.
E-4 User Cancel The measurement has been canceled. Start the measurement again as necessary.
E-5 PHONES
The headphones are connected to the PHONES
jack of this unit.
Disconnect the headphones and start the
measurement again.
E-10 Internal Error An internal error has occurred.
Exit YPAO and then turn off and on this unit. If
this error occurs repeatedly, contact the nearest
authorized Yamaha dealer or service center.
E-20 No SPEAKERS Speakers are not detected.
Press SPEAKERS A/B to select the speakers to
be used and start the measurement again.
If this error occurs even when the speakers are
properly selected, turn off this unit and check
the speaker connections.
E-21 Control Knob
The BASS/TREBLE/BALANCE/LOUDNESS
control positions are improper.
Set all the controls to the center position and
start the measurement again.
E-22 Pure Direct Pure Direct is turned on.
Press PURE DIRECT on the front panel to turn
off Pure Direct and start the measurement again.
Noisy
YPAO E-1
45 En
Optimizing the speaker settings automatically (YPAO)
English
ADVANCED
OPERATION
Warning messages
If a warning message is displayed after the measurement, you can still save the measurement results.
However, we recommend you perform YPAO again in order to use this unit with the optimal speaker settings.
Note
If more than one warning is detected, use the cursor keys (B / C) to check another warning message.
To return to the previous state after checking the warning message, press the cursor key (
D)).
Warning message Cause Remedy
W-1 Out of Phase
A speaker cable may be connected with the
reverse polarity (+/-).
check the cable connections (+/–) of the
speakers.
If the speaker is connected incorrectly, turn off
this unit and then reconnect the speaker cable.
Depending on the type of speakers or room
environment, this message may appear even if
the speakers are connected correctly. In this
case, you can ignore the message.
W-2 Over Distance
A speaker is placed more than 24 m (80 ft) from
the listening position
Move the speaker within 24m (80 ft) of the
listening position.
W-3 Level Error
There are significant volume differences
between the speakers.
Check the usage environment and cable
connections (+/–) of each speaker, and the
volume of the subwoofer. We recommend using
the same speakers or speakers with
specifications that are as similar as possible.
Out of Phase
YPAO W-1
46 En
You can configure separate playback settings for different
playback sources. This menu allows you to easily
configure settings during playback.
1 Press OPTION.
2 Use the cursor keys to select an item and
press ENTER.
Note
To return to the previous state during menu operations, press
RETURN.
3 Use the cursor keys (D / E) to select a setting.
4 To exit from the menu, press OPTION.
Option menu items
Note
Available items vary depending on the selected input source.
Volume Trim
Corrects volume differences between input sources. If you
are bothered by volume differences when switching
between input sources, use this function to correct it.
Note
This setting is applied separately to each input source.
Setting range
-10.0 dB to 0.0 dB to +10.0 dB (0.5 dB increments)
Default
0.0 dB
Signal Info.
Displays information about audio signal.
Choices
Note
To switch the information on the front display, press the cursor
keys (B / C) repeatedly.
Vol.Interlock (Volume interlock)
Enables/disables volume controls from iPhone/iTunes via
AirPlay.
Settings
Configuring playback settings for different playback sources
(Option menu)
Item Function Page
Volume Trim
Corrects volume differences between
input sources.
46
Signal Info.
Displays information about the audio
signal.
46
Auto Preset
Automatically registers FM radio
stations with strong signals as presets.
25
Clear Preset
Clears radio stations registered to
preset numbers.
27
Initiate Scan
(R-N803D only)
Performs an initial scan for DAB radio
reception.
29
Tune Aid
(R-N803D only)
Checks reception strength of each
DAB channel label.
31
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
OPTION
ENTER
Cursor keys
B / C / D / E
Volume Trim
OPTION
VOL.
A
Vol.Interlock
(Volume interlock)
Enables/Disables volume controls from
iPhone/iTunes via AirPlay.
46
Auto Playback
Selects whether to automatically play
back music from your PC/NAS or USB
storage device when the unit is turned
on or when the corresponding input
source is selected.
36, 40
FORMAT Audio format of the input signal
SAMPLING
The number of samples per second of the input
digital signal
Off Disables volume controls from iPhone/iTunes.
Ltd
(Default)
Enables volume controls from iPhone/iTunes
within the limited range (-80.0 dB to -20.0 dB and
mute).
Full
Enables volume controls from iPhone/iTunes in
the full range (-80.0 dB to +16.5 dB and mute).
Item Function Page
Configuring various functions (Setup menu)
47 En
English
ADVANCED
OPERATION
You can configure the unit’s various functions.
1 Press SETUP.
2 Use the cursor keys (B / C) to select a menu
item and press ENTER.
3 Use the cursor keys (D / E) to select a setting
and press ENTER.
Note
To return to the previous state during menu operations, press
RETURN.
4 To exit from the menu, press SETUP.
Configuring various functions (Setup menu)
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Cursor keys
B / C / D / E
Network
SETUP
Volume
SETUP
Max Volume
VOLUME
+16.5dB
MAX VOL
48 En
Configuring various functions (Setup menu)
Setup menu items
Network
Configures the network settings.
Connection
Selects the network connection method.
Note
When this unit is in the MusicCast extended mode, “Extend” is
displayed. For details on the extended mode, refer to “MusicCast
Setup Guide” on the Yamaha website.
Information
Displays the network information on the unit.
Menu item Function Page
Network
Connection Selects the network connection method. 48
Information Displays the network information on the unit. 48
IP Address Configures the network parameters (such as IP address). 49
DMC Control
Selects whether to allow a DLNA-compatible Digital Media Controller
(DMC) to control playback.
49
Standby
(Network Standby)
Selects whether to enable/disable the function that turns on the unit from
other network devices.
49
Network Name
Edits the network name (the units name on the network) displayed on
other network devices.
49
Update (Network Update) Updates the firmware via the network. 50
Bluetooth
On/Off Enables/disables the Bluetooth functions. 50
Standby
(Bluetooth Standby)
Selects whether to enable/disable the function that turns on the unit from
Bluetooth devices (Bluetooth standby).
50
YPAO
(Speaker A, Speaker B,
Speaker A+B)
YPAO On/Off Enables/disables the reflection of the YPAO measurement. 50
VOL
(YPAO Volume)
Enables/disables the YPAO volume function. 50
Volume
Max Volume Sets the maximum volume to prevent excessive loudness. 50
Initial Volume Sets the initial volume for when this receiver is turned on. 50
AutoPowerStdby
(Auto Power Standby)
Sets the amount of time for the auto standby function. 51
ECO Mode Enables/disables the eco mode (power saving mode). 51
Wired
Select this option when you want to connect
the unit to a network with a commercially-
available network cable (p. 14).
Wireless
Select this option when you want to connect
the unit to a network via the wireless router or
access point (p. 16).
WirelessDirect
Select this option when you want to connect a
mobile device to the unit directly. For details
on settings, see “Connecting a mobile device
to the unit directly (Wireless Direct)” (p. 19).
NEW FW
Available
Appears if an update for this unit’s firmware is
available (p. 54).
STATUS The connection status of the network.
MC NET
Status of the MusicCast Network. If “Ready”
appears, you can use the MusicCast
CONTROLLER app.
MAC
Displays MAC address of the unit. MAC
address will vary depending on the connection
method (wired LAN connection or wireless
LAN / Wireless Direct connection).
SSID
(When using wireless LAN connection or
Wireless Direct) The SSID of this unit on the
wireless network.
IP IP address
SUBNET Subnet mask
GATEWAY The IP address of the default gateway
DNS P The IP address of the primary DNS server
DNS S The IP address of the secondary DNS server
49 En
Configuring various functions (Setup menu)
English
ADVANCED
OPERATION
IP Address
Configures the network parameters (such as IP address).
DHCP
Select whether to use a DHCP server.
Manual network settings
1 Set “DHCP” to “Off”.
2 Use the cursor keys (B / C) to select a
parameter type.
3 Use the cursor keys (D / E) to select the edit
position.
(Example: IP address setting)
Use the cursor keys (D / E) to switch between
segments (Address1, Address2...) of the address.
4 Use the Cursor keys (B / C) to change a
value.
5 To exit from the menu, press SETUP.
DMC Control
Selects whether to allow DLNA-compatible Digital Media
Controller (DMC) to control playback.
Note
A Digital Media Controller (DMC) is a device that can control
other network devices through the network. When this function is
enabled, you can control playback of the unit from DMCs (such
as Windows Media Player 12) on the same network.
Standby (Network Standby)
Selects whether the unit can be turned on from other
network devices (network standby).
Network Name
Edits the network name (the unit’s name on the network)
displayed on other network devices.
1 Select “Network Name” and press ENTER.
2 Press ENTER twice to enter the name edit
display.
3 Use the cursor keys (D / E) to move the edit
position and the cursor keys (B / C) to select
a character.
You can insert / delete a character, by pressing
PRESET i (insert) or PRESET j (delete).
4 To confirm the new name, press ENTER.
5 To exit from the menu, press SETUP.
Off
Does not use a DHCP server. Configure the
network parameters manually. For details, see
“Manual network settings”.
On (Default)
Uses a DHCP server to automatically obtain the
unit’s network parameters (such as IP address).
IP Specifies an IP address.
SUBNET Specifies a subnet mask.
GATEWAY Specifies the IP address of the default gateway.
DNS P
Specifies the IP address of the primary DNS
server.
DNS S
Specifies the IP address of the secondary DNS
server.
Disable Does not allow DMCs to control playback.
Enable
(Default)
Allows DMCs to control playback.
Address1•••192
IP
Off Disables the network standby function.
On
Enables the network standby function. (The unit
consumes more power than when “Off” is
selected.)
Auto
(Default)
Enables the network standby function. The unit is
set to the power saving mode when the unit is
disconnected from the network.
With an advanced energy saving design, this product achieves
a low power consumption of not more than two watts when in
Network Standby mode.
Network Name
NETWORK
R-N803 XXXXXX
NET NAME
R-N803 XXXXXX
NET NAME
50 En
Configuring various functions (Setup menu)
Update (Network Update)
Updates the firmware via the network.
Bluetooth
Configures the Bluetooth settings.
On/Off
Enables/disables the Bluetooth function (p. 32).
Standby (Bluetooth Standby)
Selects whether to enable/disable the function that turns
on the unit from Bluetooth devices (Bluetooth standby). If
this function is set to “On”, the unit automatically turns on
when a connect operation (p. 32) is performed on the
Bluetooth device.
Note
This setting is not available when “Standby (Network Standby)”
(p. 49) is set to “Off”.
YPAO
Configures the setting related to YPAO.
The following settings are available for each speaker
system (Speaker A, Speaker B, Speaker A+B).
Note
The corresponding speaker system and following settings will be
selectable after the YPAO measurement result is saved.
YPAO On/Off
Enables/disables the reflection of the YPAO measurement.
VOL (YPAO Volume)
Enables/disables the YPAO volume function. When the
YPAO Volume function is enabled, the high- and low-
frequency levels are automatically adjusted according to
the volume so that you can enjoy natural sounds even at
low volume.
Note
The YPAO Volume function is disabled when “YPAO On/Off”
is set to “Off”.
When the YPAO volume function is enabled, the YPAO VOL.
indicator on the front display lights up.
The LOUDNESS control (p. 24) does not function when the
YPAO Volume function is enabled.
Volume
Configures the volume-related settings.
Max Volume
Sets the maximum volume to prevent excessive loudness.
Setting range
-30 dB to +15.0 dB / +16.5 dB (5 dB step)
Default
+16.5 dB
Initial Volume
Sets the initial volume when the receiver is turned on.
Setting range
Off, Mute, -80.0 dB to +16.5 dB (0.5 dB Step)
Default
Off
Perform
Update
Starts the process to update the unit’s firmware.
For details, see “Updating the unit’s firmware via
the network” (p. 54).
Version
Displays the version of the firmware installed on
the unit.
ID Displays the system ID number.
Off Disables the Bluetooth function.
On (Default)
Enables the Bluetooth function. Immediately
after selecting the “On”, output of the network
source is paused.
Off Disables the Bluetooth standby function.
On (Default)
Enables the Bluetooth standby function. (The
unit consumes more power than when “Off” is
selected.)
Off Disables the reflection of the YPAO measurement.
On (Default) Enables the reflection of the YPAO measurement.
Off Disables the YPAO Volume function.
On (Default) Enables the YPAO Volume function.
51 En
Configuring various functions (Setup menu)
English
ADVANCED
OPERATION
AutoPowerStdby
(Auto Power Standby)
Enables/disables the auto-standby function. If you do not
operate the unit for the specified time, the unit will
automatically go into standby mode.
Default
U.K. and Europe models: On
Other models: Off
Note
Just before the unit enters standby mode, “AutoPowerStdby”
appears and then countdown starts in the front display.
ECO Mode
Enables/disables the eco (power saving) mode. When the
eco mode is enabled, you can reduce the unit’s power
consumption.
The new setting will take effect after the unit is restarted.
Be sure to press ENTER to restart the unit after selecting a
setting.
Note
When “ECO Mode” is set to “On”, the front display may become
dark.
Off
Does not set the unit to standby mode
automatically.
On
Sets the unit to standby mode automatically.
While NET, BLUETOOTH or USB is selected as
the input source, the unit will switch to standby
mode if the selected source is not played back for
20 minutes.
For all input sources, the unit will switch to
standby mode if it is not operated for 8 hours.
Off
(Default)
Disables the eco mode.
On Enables the eco mode.
52 En
Configure the system settings of the unit using the front
panel controls.
1 Press A (power) to turn off the unit.
2
While holding down RETURN, press
A (power).
3 Rotate SELECT/ENTER to select an item.
4 Press SELECT/ENTER to select a setting.
5 Press A (power) to set the unit to turn off and
turn it on again.
The new settings take effect.
ADVANCED SETUP menu items
Checking the firmware version
(VERSION)
Check the version of firmware currently installed on the
unit.
Note
You can also check the firmware version in “Update (Network
Update)” (p. 50) in the “Setup” menu.
It may take a while until the firmware version is displayed.
Changing the speaker impedance
setting (SP IMP.)
Change the unit’s speaker impedance settings depending
on the impedance of the speakers connected.
Settings
Selecting the remote control ID
(REMOTE ID)
Change the unit’s remote control ID so that it matches the
remote control’s ID.
Select “ID1” normally. Select “AUTO” only when you
use the remote control supplied with some Yamaha player.
Settings
ID1 (Default), AUTO
Configuring the system settings (ADVANCED SETUP menu)
Item Function Page
VERSION
Checks the version of firmware
currently installed on the unit.
52
SP IMP.
Changes the speaker impedance
setting.
52
REMOTE ID Selects the unit’s remote control ID. 52
TU
(Asia and General models only)
Sets tuner frequency step.
53
INIT Restores the default settings. 53
UPDATE Updates the firmware. 53
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
A (power)
SELECT/ENTER
RETURN
DISPLAY
4 MIN
Select this option when you connect speakers with
an impedance of 4 ohms to less than 8 ohms to the
unit.
8 MIN
(Default)
Select this option when you connect speakers with
an impedance of 8 ohms or more to the unit.
VERSION••xx.xx
SP IMP.••8¬MIN
REMOTE ID••ID1
53 En
Configuring the system settings (ADVANCED SETUP menu)
English
ADVANCED
OPERATION
Setting tuner frequency step (TU)
(Asia and General models only)
Selects the step size for locating tuner frequencies.
Settings
FM100/AM10, FM50/AM9 (Default)
Restoring the default settings (INIT)
Restores the default settings for the unit.
Choices
Updating the firmware (UPDATE)
New firmware that provides additional features or product
improvements will be released as needed. If the unit is
connected to the Internet, you can download the firmware
via the network. For details, refer to the information
supplied with updates.
Firmware update procedure
Do not perform this procedure unless firmware update is
necessary. Also, make sure you read the information
supplied with updates before updating the firmware.
1 Press SELECT/ENTER repeatedly to select
“USB” or “NETWORK” and press DISPLAY to
start firmware update.
Choices
Note
If the unit detects newer firmware over the network, “NEW FW
Available” appears as the “Information” menu item in
“Network”. In this case, you can also update the unit’s firmware
by following the procedure in “Updating the unit’s firmware via
the network” (p. 54).
ALL Restores the default settings for the unit.
NETWORK
Initialize all of the network, Bluetooth and USB
settings. When performing the initialization, the
preset (p. 41) registered by NET/USB input will
be cleared.
CANCEL Does not perform an initialization.
TU••••FM50/AM9
INIT••••CANCEL
USB Update the firmware using a USB memory device.
NETWORK Update the firmware via the network.
UPDATE•NETWORK
54 En
New firmware that provides additional features or product improvements will be released as needed. If the unit is
connected to the Internet, you can download the firmware via the network and update it.
Note
You can also update the firmware using the USB memory device
from the “ADVANCED SETUP” menu (p. 53).
1 Press SETUP.
2 Use the cursor keys (B / C) to select
“Network” and press ENTER.
3 Use the cursor keys (B / C) to select
“Information” and press ENTER.
If new firmware is available, “NEW FW Available”
appears on the front display.
4 Press RETURN to return the previous state.
5 Use the cursor keys (B / C) to select
“Update” and press ENTER.
6 To start the firmware update, press ENTER.
The unit to restart and the firmware update starts.
Note
To cancel the operation without updating the firmware, press
SETUP.
7 If “UPDATE SUCCESS” appears on the front
display, press A (power) on the front panel.
The firmware update is complete.
Notification of new firmware update
When new firmware is available on the network, “NEW
FW” will be displayed on the front display for a short
period of time when the unit is turned on.
To update the firmware, press ENTER (as described in
Step 6) while the notification is displayed. If “UPDATE
SUCCESS” appears on the front display, press A (power)
on the front panel to turn off the unit.
Updating the unit’s firmware via the network
Do not operate the unit or disconnect the power cable or network cable during firmware update. Firmware update takes about 5
minutes or more (depending on your Internet connection speed).
If the unit is connected to the wireless network via a wireless network adapter, network update may not be possible depending on
the condition of the wireless connection. In this case, update the firmware using the USB memory device (p. 53).
Notice
PRESET
MEMORY
SETUP
HOME
MUTENOW PLAYING
VOLUME
RETURN
ENTER
OPTION
RETURN
SETUP
ENTER
Cursor keys
B / C
Available
NEW FW
Perform Update
UPDATE
Update [ENTER]
NEW FW
55 En
English
ADDITIONAL
INFORMATION
ADDITIONAL INFORMATION
Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or
if the instructions below do not help, set this unit to standby mode, disconnect the power cable, and contact the nearest
authorized Yamaha dealer or service center.
General
Troubleshooting
Problem Possible cause Remedy
See
page
The power does not
turn on.
The protection circuitry has been activated
three times consecutively. If the unit is in
this condition, the power indicator on the
front panel blinks when you try to turn on
the power.
As a safety precaution, capability to turn on the power
is disabled. Contact your nearest Yamaha dealer or
service center to request repair.
The power cord is not connected or the
plug is not completely inserted.
Connect the power cord firmly.
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
11
The internal microcomputer has frozen,
due to an external electric shock (such as
lightning or excessive static electricity) or
to a drop in the power supply voltage.
Press A (power) on the front panel to turn off the unit
and turn it on again after at least 15 seconds elapse.
(If the problem persists, disconnect the power cable
from the AC wall outlet and plug it again.)
The power does not
turn off.
The internal microcomputer has frozen,
due to an external electric shock (such as
lightning or excessive static electricity) or
to a drop in the power supply voltage.
Press A (power) on the front panel to turn off the unit
and turn it on again after at least 15 seconds elapse.
(If the problem persists, disconnect the power cable
from the AC wall outlet and plug it again.)
No sound. Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
10
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or one of the input
selection key on the remote control).
22
The SPEAKERS A/B switches are not set
properly.
Turn on the corresponding SPEAKERS A or
SPEAKERS B.
22
Speaker connections are not secure. Secure the connections.
10
Output has been muted. Turn off the mute.
8
Headphones are connected to the
PHONES jack.
Disconnect the headphones.
5
The Max volume or Initial volume setting
is set too low.
Check the settings for “Max Volume” and “Initial
Volume” in the “Setup” menu.
50
The component corresponding to the
selected input source is turned off or is not
playing.
Turn the component on and make sure it is playing.
The audio output of a device connected to
a digital audio input (COAXIAL/
OPTICAL jacks) is set to other than PCM.
Set the audio output of the connected device to PCM.
56 En
Troubleshooting
Remote control
The sound suddenly
goes off.
The protection circuitry has been activated
because of a short circuit, etc.
Set the speaker impedance to match your speakers.
52
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
11
This unit has become too hot. Make sure the openings on the top panel are not
blocked.
The auto power standby function has
turned this unit off.
Change the auto power standby (“AutoPowerStdby”
in the “Setup” menu) to turn off.
51
Only the speaker on
one side can be
heard.
Incorrect cable connections. Connect the cables properly. If the problem persists,
the cables may be defective.
10
Incorrect setting for the speaker balance. Set the BALANCE control to the appropriate
position.
23
There is a lack of bass
and no ambience.
The + and – wires are connected in
reverse at the amplifier or the speakers.
Connect the speaker wires to the correct + and –
phase.
11
A “humming” sound
can be heard.
Incorrect cable connections. Connect the audio plugs firmly. If the problem
persists, the cables may be defective.
10
No connection from the turntable to the
GND terminal.
Make the GND connection between the turntable and
this unit.
10
The volume level is
low while playing a
record.
The record is being played on a turntable
with an MC cartridge.
The turntable should be connected to this unit through
the MC head amplifier.
The sound is
degraded when
listening with the
headphones
connected to the CD
player or the tape
deck connected to
this unit.
The power of this unit is turned off, or this
unit is set to standby mode.
Turn on the power of this unit.
The sound level is
low.
The loudness control function is
operating.
Turn down the volume, set the LOUDNESS control
to the FLAT position, and then adjust the volume
again.
24
Problem Possible cause Remedy
See
page
The remote control
does not work nor
function properly.
Wrong distance or angle. The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees off-
axis from the front panel.
9
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
The batteries are weak. Replace all batteries.
9
Problem Possible cause Remedy
See
page
57 En
Troubleshooting
English
ADDITIONAL
INFORMATION
FM reception
AM reception (R-N803)
DAB reception (R-N803D)
Problem Possible cause Remedy
See
page
The FM radio
reception strength is
poor, and noise can
be heard.
The unit is receiving radio interference,
such as multipath reflections.
Change the antenna height, direction, or place of
installation.
The unit is receiving in a region located
far away from the radio station.
Press MODE on the front panel to select “MONO”
(monaural mode).
25
Use a commercially-available outdoor antenna.
The radio station
cannot be
automatically
selected.
The FM radio signal is weak. Use a commercially-available outdoor antenna.
Select the station manually.
25
Problem Possible cause Remedy
See
page
The AM radio
reception strength is
poor, and noise can
be heard.
The unit is picking up noise from sources
such as a fluorescent light or a motor.
In some environments, it may be difficult to
completely eliminate noise. However, using a
commercially-available outdoor antenna may help to
reduce noise.
The AM radio signal is weak. Change the direction of the AM antenna.
13
Select the station manually.
25
Use a commercially-available outdoor antenna.
Connect the supplied AM antenna to the
ANTENNA(AM) jack.
AM radio stations
cannot be registered
(preset).
The stations may have been registered
automatically (Auto Preset).
Auto presets can be used with FM radio stations
only. AM radio stations must be manually registered.
26
Problem Possible cause Remedy
See
page
Cannot tune into any
DAB stations.
The initial scan has not been performed. Perform the initial scan.
29
The DAB radio signal is weak. Change the antenna height, direction, or place of
installation.
13
There is no DAB coverage in your area. Check with your dealer or WorldDMB Online at
“http://www.worlddab.org” for a listing of the DAB
coverage in your area.
The initial scan is not
successful
(“NotFound” appears
on the front display).
The DAB radio signal is weak. Change the antenna height, direction, or place of
installation.
13
There is no DAB coverage in your area. Check with your dealer or WorldDMB Online at
“http://www.worlddab.org” for a listing of the DAB
coverage in your area.
58 En
Troubleshooting
Bluetooth
The DAB radio
reception strength is
poor, and noise
(such as hiss,
crackle and jitter)
can be heard.
The DAB radio signal is weak. Change the antenna height, direction, or place of
installation.
13
The DAB information
cannot be displayed
or is inaccurate.
The DAB station may be temporarily out
of service, or the DAB station
information is not provided by the DAB
broadcaster.
Contact the DAB broadcaster.
Problem Possible cause Remedy
See
page
The unit cannot
connect to a
Bluetooth device.
The Bluetooth function is disabled. In the “Setup” menu, set “Bluetooth (On/Off)” to
“On”.
50
The unit is connected to a different
Bluetooth device.
Disconnect the current Bluetooth connection and
connect with the desired Bluetooth device.
33
The unit is too far from the Bluetooth
device.
Move the Bluetooth device closer to this unit.
A device emitting electromagnetic waves
(such as a microwave oven and a
wireless device) may be located nearby.
Do not use this unit near devices that emit
electromagnetic waves.
The Bluetooth device does not support
the A2DP protocol.
Use a Bluetooth device that supports the A2DP
protocol.
62
The connection profile registered in the
Bluetooth device may not be functioning
correctly for some reason.
Delete the connection profile in the Bluetooth
device, and then connect the Bluetooth device to this
unit.
32
The passkey on the Bluetooth adapter or
other device may be set to a code besides
“0000”.
Use a Bluetooth device on which the passkey is set
to “0000”.
No sound can be
heard, or the sound
cuts off
intermittently.
The volume on the Bluetooth device is
too low.
Raise the volume on the Bluetooth device.
The sound output on the Bluetooth
device may not be set to this unit.
Select this unit as the output destination on the
Bluetooth device.
32
The connection to the Bluetooth device is
cut off.
Reconnect with the Bluetooth device.
32
The unit is too far from the Bluetooth
device.
Move the Bluetooth device closer to this unit.
A device emitting electromagnetic waves
(such as a microwave oven and a
wireless device) may be located nearby.
Do not use this unit near devices that emit
electromagnetic waves.
Problem Possible cause Remedy
See
page
59 En
Troubleshooting
English
ADDITIONAL
INFORMATION
USB/network
Problem Possible cause Remedy
See
page
The unit does not
detect the USB
storage device.
The USB storage device is not connected
to the USB jack securely.
Turn off the unit, reconnect your USB device, and
turn the unit on again.
39
The file system of the USB storage
device is not FAT16 or FAT32.
Use a USB storage device with FAT16 or FAT32
format.
62
Folders and files in
the USB device
cannot be viewed.
The data in the USB storage device is
protected by the encryption.
Use a USB storage device without an encryption
function.
62
The network function
cannot be used.
The network information (IP address)
has not been properly acquired.
Enable the DHCP server function on your router and
set “DHCP” in the “Setup” menu to “On” on the
unit. If you want to configure the network
parameters manually, make sure that the IP address
of this unit is different from that of other devices on
the network.
49
The unit cannot
connect to the
Internet via wireless
LAN router (access
point).
The wireless LAN router (access point)
is turned off.
Turn on the wireless LAN router (access point).
The unit is too far from the wireless LAN
router (access point).
Set up this unit closer to the wireless LAN router
(access point).
There is an object blocking the signal
path between this unit and the wireless
LAN router (access point).
Set up this unit so that there is a clear signal path
between this unit and the wireless LAN router
(access point).
A wireless network
cannot be found.
A device emitting electromagnetic waves
(such as a microwave oven and a
wireless device) may be located nearby.
When connecting wirelessly, do not use this unit
near devices that emit electromagnetic waves.
Access to the network is restricted, due to
a firewall on the wireless LAN router
(access point).
Check the firewall settings of the wireless LAN
router (access point).
The PC (server)
cannot be detected.
The media sharing settings on the PC
(server) is incorrect.
Change the media sharing settings so that this unit
can access the folder on the PC (server).
34
Access is restricted due to the security
settings on the PC (server) or router.
Check the security settings on the computer (server)
and wireless LAN router (access point).
This unit and the PC (server) are not
connected to the same network.
Check the network and router settings, to make sure
that they are connected to the same network.
The files on the PC
(server) cannot be
viewed (played
back).
The file format may not be compatible
with this unit or with the PC (server).
Use a file format that is compatible with this unit and
with the PC. For details on supported file formats,
see “Supported file formats”.
62
Internet radio cannot
be played.
The selected Internet radio station is
currently not available.
There may be a network problem at the radio station,
or the service may have been stopped. Try the station
later or select another station.
The selected Internet radio station is
currently broadcasting silence.
Some Internet radio stations broadcast silence at
certain of times of the day. Try the station later or
select another station.
Access to the network is restricted due to
the firewall settings on a network device,
such as a wireless LAN router (access
point).
Check the firewall settings of your network devices.
The Internet radio can be played only when it passes
through the port designated by each radio station.
The port number varies depending on the radio
station.
60 En
Troubleshooting
This unit cannot be
detected when using
AirPlay on an
iPhone.
A wireless LAN router (access point)
that supports multiple SSIDs is used.
The network separator function on the wireless LAN
router (access point) may be preventing this unit
from being accessed. When connecting to this unit
with an iPhone, use an SSID on which this unit can
be accessed (try connecting via the primary SSID).
The unit is not
detected when using
a dedicated
application on a
mobile device.
This unit and the mobile device are not
connected to the same network.
Check the network and router settings, to make sure
that they are connected to the same network.
A wireless LAN router (access point)
that supports multiple SSIDs is used.
The network separator function on the wireless LAN
router (access point) may be preventing this unit
from being accessed. When connecting to this unit
with a mobile device, use an SSID on which this unit
can be accessed (try connecting via the primary
SSID).
Firmware update via
the network is failed.
The network connection is no good. Try connecting again after a while, or a USB storage
device to update the firmware.
53
The unit cannot
connect to the
wireless LAN router
(access point).
MAC address filtering is enabled on the
wireless LAN router (access point).
This unit cannot connect to the wireless LAN router
(access point) if its MAC address filtering is
enabled. Change the settings on the wireless LAN
router (access point) to allow this unit to connect.
Problem Possible cause Remedy
See
page
Error indications on the front display
61 En
English
ADDITIONAL
INFORMATION
Error indications on the front display
Message Possible cause Remedy
Access denied Access to the PC is denied. Configure the sharing settings and select the unit as a device to
which music contents are shared (p. 34).
Access error The unit cannot access the USB device. Turn off the unit and reconnect your USB device. If the problem
persists, try another USB device.
The unit cannot access the iPod. Turn off the iPod and turn it on again.
The connected iPod is not supported by
the unit.
Use an iPod supported by the unit (p. 62).
There is a problem with the signal path
from the network to the unit.
Make sure your router and modem are turned on.
Check the connection between the unit and your router (or hub)
(p. 14).
Check SP Wires The speaker cables short circuit. Twist the bare wires of the cables firmly and connect to the unit
and speakers properly.
No content There are no playable files in the selected
folder.
Select a folder that contains files supported by the unit.
Please wait The unit is preparing for connecting to the
network.
Wait until the message disappears. If the message stays more than
3 minutes, turn off the unit and turn it on again.
Unable to play The unit cannot play back the songs stored
on the iPod for some reason.
Check the song data. If it cannot be played on the iPod itself, the
song data or storage area may be defective.
The unit cannot play back the songs stored
on the PC for some reason.
Check if the format of files you are trying to play is supported by
the unit. For information about the formats supported by the unit,
see “Playing back music stored on media servers (PCs/NAS)” (p.
34). If the unit supports the file format, but still cannot play back
any files, the network may be overloaded with heavy traffic.
Version error Firmware update is failed. Update the firmware again.
62 En
Supported devices
Bluetooth device
This unit supports Bluetooth devices that support
A2DP audio profile and AVRCP control profile.
Bluetooth device may not be detected by the unit or
some feature may not be compatible, depending on the
model.
USB storage device
This unit supports USB mass storage class devices
(e.g., flash memories or portable audio players) using
FAT16 or FAT32 format.
USB storage devices with encryption cannot be used.
Some features may not be compatible, depending on
the model or manufacturer of the USB storage device.
AirPlay
AirPlay works with iPhone, iPad, and iPod touch with
iOS 4.3.3 or later, Mac with OS X Mountain Lion or
later, and Mac and PC with iTunes 10.2.2 or later.
Made for.
iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus,
iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s, iPhone
5c, iPhone 5, iPhone 4s
iPad Pro (9.7" and 12.9"), iPad mini 4, iPad Air 2, iPad
mini 3, iPad Air, iPad mini 2, iPad mini, iPad (3rd and
4th generation), iPad 2
iPod touch (5th and 6th generation)
(as of June 2017)
Supported file formats
USB/PC (NAS)
* Linear PCM format only
Note
To play back FLAC files stored on a PC or NAS, you need to install server software that supports sharing of FLAC files via DLNA on
your PC or use a NAS that supports FLAC files.
Digital Rights Management (DRM) contents cannot be played back.
Supported devices and file formats
File Sampling frequency (kHz)
Quantization
bitrate (bit)
Bitrate Gapless playback
WAV * 32/44.1/48/88.2/96/176.4/192
16/24
MP3 32/44.1/48
8 to 320
WMA 32/44.1/48
8 to 320
MPEG-4 AAC 32/44.1/48
8 to 320
FLAC 32/44.1/48/88.2/96/176.4/192
16/24
ALAC 32/44.1/48/88.2/96
16/24
AIFF 32/44.1/48/88.2/96/176.4/192
16/24
DSD 2.8MHz/5.6MHz
1 ――
Trademarks
63 En
English
ADDITIONAL
INFORMATION
Supports iOS 7 or later for setup using Wireless Accessory
Configuration.
“Made for iPod,” “Made for iPhone,” and “Made for
iPad” mean that an electronic accessory has been designed
to connect specifically to iPod, iPhone, or iPad,
respectively, and has been certified by the developer to
meet Apple performance standards.
Apple is not responsible for the operation of this device or
its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod,
iPhone, or iPad may affect wireless performance.
iTunes, AirPlay, iPad, iPhone, iPod, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other
countries.
iPad Air and iPad mini are trademarks of Apple Inc.
App Store is a service mark of Apple Inc.
DLNA™ and DLNA CERTIFIED™ are trademarks or
registered trademarks of Digital Living Network Alliance.
All rights reserved.
Unauthorized use is strictly prohibited.
Windows™
Windows is a registered trademark of Microsoft
Corporation in the United States and other countries.
Internet Explorer, Windows Media Audio and Windows
Media Player are either registered trademarks or
trademarks of Microsoft Corporation in the United States
and/or other countries.
Android™
Google Play™
Android and Google Play are trademarks of Google Inc.
The Wi-Fi CERTIFIED™ Logo is a certification mark of
Wi-Fi Alliance
®
.
The Wi-Fi Protected Setup™ Identifier Mark is a
certification mark of Wi-Fi Alliance
®
.
The Bluetooth
®
word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Yamaha Corporation is under license.
Bluetooth protocol stack (Blue SDK)
Copyright 1999-2014 OpenSynergy GmbH
All rights reserved. All unpublished rights reserved.
MusicCast is a trademark or registered trademark of
Yamaha Corporation.
Yamaha Eco-Label is a mark that certifies products of
high environmental performance.
(For R-N803D)
The unit supports DAB/DAB+ tuning.
Trademarks
Explanations regarding GPL
This product utilizes GPL/LGPL open-source software in
some sections. You have the right to obtain, duplicate,
modify, and redistribute this open-source code only. For
information on GPL/ LGPL open source software, how to
obtain it, and the GPL/LGPL license, refer to the Yamaha
Corporation website
(http://download.yamaha.com/sourcecodes/musiccast/).
64 En
Network
Input jack: NETWORK x 1 (100Base-TX/10Base-T)
PC client function
Compatible with DLNA ver. 1.5
AirPlay supported
Internet radio
Streaming service
Wi-Fi function
Capable of direct connection with mobile device
Available security method
....................................... WEP, WPA2-PSK(AES), Mixed Mode
Radio frequency band ....................................................... 2.4 GHz
Radio frequency (operational frequency)
..............................................................2412 MHz to 2472 MHz
Maximum output power (E.I.R.P) ............... 17.5 dBm (56.2 mW)
Wireless network standard ................................IEEE 802.11 b/g/n
Wi-Fi settings
WPS (Wi-Fi Protected Setup) ..............................Capable of WPS
Capable of sharing with iOS devices by wireless connection.
Bluetooth related function
•Version..............................................................Bluetooth 2.1 + EDR
Frequency.............................................................................2.4 GHz
Radio frequency (operational frequency)
....................................................................2402 MHz to 2480 MHz
Maximum output power (E.I.R.P)....................... 4.0 dBm (2.5 mW)
Wireless output...................................................... Bluetooth Class 2
Profiles
Source function
The unit sink device (ex. Bluetooth headphones)
Profile: A2DP version 1.3, AVRCP version 1.6
CODEC: SBC
Sink function
The unit source device (ex. iPhone/Android)
Profile: A2DP version 1.3, AVRCP version 1.6
CODEC: SBC, AAC
USB
Input jack: USB x 1 (USB 2.0)
Capable of mass storage class USB memory
Current supply capacity: 1.0 A
Audio
Minimum RMS output power
(20 Hz to 20 kHz, 0.019% THD, 8) .....................100 W+100 W
Dynamic power per channel (IHF) (8/6/4/2)
........................................................................... 140/170/220/290 W
Maximum power per channel (1 kHz, 0.7% THD, 4)
[U.K. and Europe models] ...................................................160 W
IEC power (1 kHz, 0.04% THD, 8)
[U.K. and Europe models] ...................................................115 W
Power band width (main L/R)
(0.06%THD 40.0 W, 8) .....................................10 Hz to 50 kHz
Damping factor (SPEAKERS A)
1 kHz, 8 ....................................................................240 or more
Maximum effective output power (JEITA)
(1 kHz, 10% THD, 8)
[Asia and General models]...................................................145 W
Input sensitivity/input impedance
PHONO (MM) ........................................................ 2.5 mV/47 k
CD, etc. ................................................................. 200 mV/47 k
Maximum input signal
PHONO (MM) (1 kHz, 0.03% THD) ................................. 45 mV
CD, etc. (1 kHz, 0.5% THD)..................................................2.2 V
Output level/output impedance
CD, etc. (input 1 kHz, 200 mV)
OUT ................................................................... 200 mV/1.0 k
SUBWOOFER OUT.............................................. 4.0 V/1.2 k
(Cut off frequency) ........................................................... 90 Hz
PHONES (8 load)..............................................470 mV/470
Frequency response
CD, etc. (20 Hz to 20 kHz) ........................................... 0 ± 0.5 dB
CD, etc. (10 Hz to 100 kHz, PURE DIRECT on) ........ 0 ± 1.0 dB
RIAA equalization deviation
PHONO (MM).................................................................. ± 0.5 dB
Total harmonic distortion
PHONO (MM) to OUT
(20 Hz to 20 kHz, 2.5 V) ....................................... 0.03% or less
CD, etc. to SPEAKERS
(20 Hz to 20 kHz, 50.0 W, 8)............................ 0.019% or less
Signal to noise ratio (IHF-A Network)
PHONO (MM) (input shorted, 5 mV)
[U.S.A., Canada, Asia, General models]..............82 dB or more
[U.K., Europe, Korea, Australia models] .............75 dB or more
CD, etc. (input shorted, 200 mV) ..........................100 dB or more
Residual noise (IHF-A network) .............................................70 µV
Channel separation
CD, etc. (5.1 k input shorted, 1 kHz/10 kHz)
.........................................................................65/50 dB or more
Tone control characteristics
BASS
Boost/cut (20 Hz) ........................................................... ± 10 dB
Turnover frequency ......................................................... 300 Hz
TREBLE
Boost/cut (20 kHz) ........................................................ ± 10 dB
Turnover frequency ........................................................ 3.0 kHz
Continuous loudness control
Attenuation 1 kHz................................................................ -30 dB
Gain tracking error (+16.5 to -80 dB) ......................... 0.5 dB or less
Digital input (OPTICAL/COAXIAL)
Support audio sample rate ..........32/44.1/48/88.2/96/176.4/192 kHz
FM
Tuning range
[U.S.A. and Canada models] ...........................87.5 to 107.9 MHz
[Asia and General models] ....... 87.5/87.50 to 108.0/108.00 MHz
[U.K., Europe, Korea, Australia models] ....87.50 to 108.00 MHz
50 dB quieting sensitivity (IHF, 1 kHz, 100% MOD.)
Mono ................................................................. 3.0 µV (20.8 dBf)
Signal to noise ratio (IHF)
Mono/stereo ...............................................................69 dB/67 dB
Harmonic distortion (1 kHz)
Mono/stereo ................................................................. 0.5%/0.6%
Antenna input ..........................................................75 unbalanced
AM (R-N803)
Tuning range
[U.S.A. and Canada models] .............................. 530 to 1710 kHz
[Asia and General models] ................. 530/531 to 1710/1611 kHz
[Korea model]...................................................... 531 to 1611 kHz
DAB (R-N803D)
Tuning range...........................................174 to 240 MHz (Band III)
Support audio format
.............................MPEG 1 Layer II/MPEG 4 HE AAC v2 (AAC+)
Antenna input ..........................................................75 unbalanced
General
Power supply
[U.S.A. and Canada models] ............................. AC 120 V, 60 Hz
[General model] .......................AC 110-120/220-240 V, 50/60 Hz
[Korea model]..................................................... AC 220 V, 60 Hz
[Australia model] ............................................... AC 240 V, 50 Hz
[U.K. and Europe models] ................................. AC 230 V, 50 Hz
[Asia model] ......................................... AC 220-240 V, 50/60 Hz
Power consumption ................................................................ 250 W
Off mode.................................................................................. 0.1 W
Specifications
65 En
Specifications
English
ADDITIONAL
INFORMATION
Standby power consumption (reference data) ......................... 0.1 W
Network Standby on
Wired .................................................................................... 1.7 W
Wireless (Wi-Fi/Wireless Direct/Bluetooth)......................... 1.8 W
Maximum power consumption (1 kHz, 8, 10% THD)
[Asia and General models] .................................................. 450 W
Dimensions (W H D) ................................ 435 151 392 mm
(17-1/8" 6" 15-7/16")
* Including legs and protrusions
Reference Dimensions (W H D) (with wireless antenna upright)
......................................................................... 435 215 392 mm
(17-1/8" 8-1/2" 15-7/16")
* Including legs and protrusions
Weight..................................................................11.0 kg (24.25 lbs)
* The contents of this manual apply to the latest specifications as of
the publishing date. To obtain the latest manual, access the Yamaha
website then download the manual file.
66 En
A
AC IN jack....................................................................... 7
ADVANCED SETUP menu.......................................... 52
AirPlay........................................................................... 38
AM antenna ................................................................... 13
AM radio ....................................................................... 25
ANTENNA terminals...................................................... 7
Auto Playback, option menu ......................................... 46
Auto preset, FM radio stations ...................................... 25
Auto Preset, option menu .............................................. 46
Automatic playback, PC music content......................... 36
Automatic playback, USB content ................................ 40
Automatic speaker settings............................................ 42
AutoPowerStdby (Auto Power Standby),
setup menu................................................................. 51
B
BALANCE control........................................................ 23
Banana plug, connection ............................................... 11
BASS control................................................................. 23
Batteries, remote control ................................................. 9
Bi-wire connection ........................................................ 12
Bluetooth device playback ............................................ 32
Bluetooth indicator .......................................................... 6
Bluetooth, setup menu................................................... 50
C
CD jacks .......................................................................... 7
CD player, connection................................................... 10
Clear Preset, option menu.............................................. 46
Clearing preset station ................................................... 27
COAXIAL jacks.............................................................. 7
Connection, Network, setup menu ................................ 48
Control Knob, front display message............................ 44
D
DAB antenna ................................................................. 13
DAB radio ..................................................................... 29
DIMMER......................................................................... 4
Disconnect MIC, front display message........................ 43
Disconnection, Bluetooth connection............................ 33
DLNA............................................................................ 34
DMC Control, Network, setup menu ............................ 49
DVD player, connection................................................ 10
E
ECO Mode, setup menu ................................................ 51
[ENTER]:Start, front display message.......................... 43
Error messages, YPAO.................................................. 44
F
Firmware update via network........................................ 54
Firmware update, ADVANCED SETUP menu ............ 53
Firmware version, ADVANCED SETUP menu ........... 52
FM antenna.................................................................... 13
FM radio ........................................................................ 25
Front display ................................................................... 6
Front display, switching information............................ 22
H
HOME, remote control ................................................... 8
I
Information, Network, setup menu ............................... 48
INIT, ADVANCED SETUP menu............................... 53
Initialize, ADVANCED SETUP menu......................... 53
Initiate Scan, option menu ............................................ 46
Input selection keys, remote control............................... 8
INPUT selector ............................................................... 5
Internal Error, front display message............................ 44
Internet radio................................................................. 37
iOS device setting sharing,
wireless network connection..................................... 16
IP Address, Network, setup menu ................................ 49
iPod content playback, AirPlay .................................... 38
iTunes content playback, AirPlay................................. 38
L
Level Error, front display message............................... 45
LINE jacks ...................................................................... 7
LOUDNESS control ..................................................... 24
M
Manual preset, FM/AM radio stations.......................... 26
Manual setting, wireless network connection............... 18
Media sharing setup...................................................... 34
Message, front display .................................................. 61
MusicCast ..................................................................... 20
MUTE ............................................................................. 6
N
NAS content playback .................................................. 34
Network cable, connection ........................................... 14
Network connection...................................................... 15
NETWORK jack............................................................. 7
Network Name, Network, setup menu.......................... 49
Network, setup menu .................................................... 48
No MIC, front display message .................................... 44
No Signal, front display message ................................. 44
No SPEAKERS, front display message........................ 44
No Warning, front display message.............................. 43
Noisy, front display message........................................ 44
NOW PLAYING, remote control................................... 8
O
OPTICAL jacks .............................................................. 7
Option menu ................................................................. 46
Out of Phase, front display message............................. 45
Over Distance, front display message........................... 45
P
Pairing, Bluetooth device.............................................. 32
PCs content playback.................................................... 34
Index
67 En
Index
English
ADDITIONAL
INFORMATION
PHONES jack ................................................................. 5
PHONES, front display message.................................. 44
PHONO jacks ................................................................. 7
Playback keys ................................................................. 9
Playback, Bluetooth device contents ............................ 32
Playing back, PCs/NAS content ................................... 34
Playing back, USB content........................................... 39
Power cord, connection ................................................ 14
Power indicator............................................................... 4
Preset function, DAB.................................................... 30
Preset, song/streaming station ...................................... 41
PURE DIRECT switch ................................................. 23
Pure Direct, front display message ............................... 44
R
Radio Data System tuning ............................................ 28
Remote control ID, ADVANCED SETUP menu......... 52
Repeat playback, AirPlay ............................................. 38
Repeat playback, PC music content.............................. 35
Repeat playback, USB content ..................................... 40
Result Info., front display message............................... 43
RETURN ........................................................................ 5
S
SELECT/ENTER............................................................ 5
Setup menu ................................................................... 47
Shuffle playback, AirPlay............................................. 38
Shuffle playback, PC music content............................. 35
Shuffle playback, USB content..................................... 40
Signal Info., option menu ............................................. 46
Signal strength indicator ................................................. 6
SLEEP............................................................................. 6
Sleep timer .................................................................... 24
SP IMP., ADVANCED SETUP menu ......................... 52
Speaker impedance, ADVANCED SETUP menu........ 52
Speaker, connection...................................................... 10
SPEAKERS A/B............................................................. 5
SPEAKERS terminals .................................................... 7
Standby (Network Standby), Network, setup menu ..... 49
STEREO ......................................................................... 6
SUBWOOFER OUT jack............................................... 7
Subwoofer, connection ................................................. 10
T
TREBLE control........................................................... 23
TRIGGER OUT jacks..................................................... 7
Tune Aid, option menu ................................................. 46
TUNED........................................................................... 6
Turntable, connection ................................................... 10
U
Update (Network Update), Network, setup menu ........ 50
UPDATE, ADVANCED SETUP menu ....................... 53
USB content playback .................................................. 39
User Cancel, front display message.............................. 44
V
Verification, network connection ................................. 20
VERSION, ADVANCED SETUP menu ..................... 52
Vol.Interlock (Volume interlock), option menu........... 46
VOLUME control ........................................................... 5
Volume Trim, option menu........................................... 46
Volume, setup menu ..................................................... 50
W
WAC ............................................................................. 15
Warning messages, YPAO............................................ 45
Wireless antenna ........................................................... 14
Wireless Direct.............................................................. 19
WPS push button configuration,
wireless network connection ..................................... 17
Y
YPAO............................................................................ 42
YPAO VOL..................................................................... 6
YPAO, setup menu ....................................................... 50
68 En
(weee_battery_eu_en_02)
Information for users on collection and
disposal of old equipment and used batteries:
These symbols on the products, packaging, and/or
accompanying documents mean that used electrical
and electronic products and batteries should not be
mixed with general household waste.
For proper treatment, recovery and recycling of old
products and used batteries, please take them to
applicable collection points, in accordance with your
national legislation.
By disposing of these products and batteries
correctly, you will help to save valuable resources
and prevent any potential negative effects on human
health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling
of old products and batteries, please contact your
local municipality, your waste disposal service or the
point of sale where you purchased the items.
For business users in the European Union:
If you wish to discard electrical and electronic
equipment, please contact your dealer or supplier for
further information.
Information on Disposal in other Countries
outside the European Union:
These symbols are only valid in the European Union.
If you wish to discard these items, please contact
your local authorities or dealer and ask for the
correct method of disposal.
Note for the battery symbol (bottom two
symbol examples):
This symbol might be used in combination with a
chemical symbol. In this case it complies with the
requirement set by the EU Battery Directive for the
chemical involved.
69 En
EN English
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Yamaha Music Europe GmbH declares that the radio
equipment type [R-N803D] is in compliance with Directive 2014/
53/EU. The full text of the EU declaration of conformity is
available at the following internet address:
https://europe.yamaha.com/en/support/compliance/doc.html
FR French
DECLARATION UE DE CONFORMITE SIMPLIFIEE
Le soussigné, Yamaha Music Europe GmbH, déclare que
l'équipement radioélectrique du type [R-N803D] est conforme à la
directive 2014/53/UE. Le texte complet de la déclaration UE de
conformité est disponible à l'adresse internet suivante:
https://europe.yamaha.com/en/support/compliance/doc.html
DE German
VEREINFACHTE EU-KONFORMITÄTSERKLÄRUNG
Hiermit erklärt Yamaha Music Europe GmbH, dass der
Funkanlagentyp [R-N803D] der Richtlinie 2014/53/EU entspricht.
Der vollständige Text der EU-Konformitätserklärung ist unter der
folgenden Internetadresse verfügbar:
https://europe.yamaha.com/en/support/compliance/doc.html
SV Swedish
FÖRENKLAD EU-FÖRSÄKRAN OM ÖVERENSSTÄMMELSE
Härmed försäkrar Yamaha Music Europe GmbH att denna typ av
radioutrustning [R-N803D] överensstämmer med direktiv 2014/
53/EU. Den fullständiga texten till EU-försäkran om
överensstämmelse finns på följande webbadress:
https://europe.yamaha.com/en/support/compliance/doc.html
IT Italian
DICHIARAZIONE DI CONFORMITÀ UE SEMPLIFICATA
Il fabbricante, Yamaha Music Europe GmbH, dichiara che il tipo
di apparecchiatura radio [R-N803D] è conforme alla direttiva
2014/53/UE. Il testo completo della dichiarazione di conformità
UE è disponibile al seguente indirizzo Internet:
https://europe.yamaha.com/en/support/compliance/doc.html
ES Spanish
DECLARACIÓN UE DE CONFORMIDAD SIMPLIFICADA
Por la presente, Yamaha Music Europe GmbH declara que el tipo
de equipo radioeléctrico [R-N803D] es conforme con la Directiva
2014/53/UE. El texto completo de la declaración UE de
conformidad está disponible en la dirección Internet siguiente:
https://europe.yamaha.com/en/support/compliance/doc.html
NL Dutch
VEREENVOUDIGDE EU-CONFORMITEITSVERKLARING
Hierbij verklaar ik, Yamaha Music Europe GmbH, dat het type
radioapparatuur [R-N803D] conform is met Richtlijn 2014/53/EU.
De volledige tekst van de EU-conformiteitsverklaring kan worden
geraadpleegd op het volgende internetadres:
https://europe.yamaha.com/en/support/compliance/doc.html
BG Bulgarian
ОПРОСТЕНА ЕС ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ
С настоящото Yamaha Music Europe GmbH декларира, че този
тип радиосъоръжение [R-N803D] е в съответствие с
Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията
за съответствие може да се намери на следния интернет
адрес:
https://europe.yamaha.com/en/support/compliance/doc.html
CS Czech
ZJEDNODUŠENÉ EU PROHLÁŠENÍ O SHODĚ
Tímto Yamaha Music Europe GmbH prohlašuje, že typ rádiového
zařízení [R-N803D] je v souladu se směrnicí 2014/53/EU. Úplné
znění EU prohlášení o shodě je k dispozici na této internetové
adrese:
https://europe.yamaha.com/en/support/compliance/doc.html
DA Danish
FORENKLET EU-OVERENSSTEMMELSESERKLÆRING
Hermed erklærer Yamaha Music Europe GmbH, at
radioudstyrstypen [R-N803D] er i overensstemmelse med direktiv
2014/53/EU. EU-overensstemmelseserklæringens fulde tekst kan
findes på følgende internetadresse:
https://europe.yamaha.com/en/support/compliance/doc.html
ET Estonian
LIHTSUSTATUD ELI VASTAVUSDEKLARATSIOON
Käesolevaga deklareerib Yamaha Music Europe GmbH, et
käesolev raadioseadme tüüp [R-N803D] vastab direktiivi 2014/53/
EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on
kättesaadav järgmisel internetiaadressil:
https://europe.yamaha.com/en/support/compliance/doc.html
EL Greek
ΑΠΛΟΥΣΤΕΥΜΕΝΗ ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ΕΕ
Με την παρούσα ο/η Yamaha Music Europe GmbH, δηλώνει ότι ο
ραδιοεξοπλισμός [R-N803D] πληροί την οδηγία 2014/53/ΕΕ.
Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται
στην ακόλουθη ιστοσελίδα στο διαδίκτυο:
https://europe.yamaha.com/en/support/compliance/doc.html
HR Croatian
POJEDNOSTAVLJENA EU IZJAVA O SUKLADNOSTI
Yamaha Music Europe GmbH ovime izjavljuje da je radijska
oprema tipa [R-N803D] u skladu s Direktivom 2014/53/EU.
Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj
internetskoj adresi:
https://europe.yamaha.com/en/support/compliance/doc.html
LV Latvian
VIENKĀRŠOTA ES ATBILSTĪBAS DEKLARĀCIJA
Ar šo Yamaha Music Europe GmbH deklarē, ka radioiekārta
[R-N803D] atbilst Direktīvai 2014/53/ES.
Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta
vietnē:
https://europe.yamaha.com/en/support/compliance/doc.html
LT Lithuanian
SUPAPRASTINTA ES ATITIKTIES DEKLARACIJA
Aš, Yamaha Music Europe GmbH, patvirtinu, kad radijo įrenginių
tipas [R-N803D] atitinka Direktyvą 2014/53/ES.
Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto
adresu:
https://europe.yamaha.com/en/support/compliance/doc.html
HU Hungarian
EGYSZERŰSÍTETT EU-MEGFELELŐSÉGI NYILATKOZAT
Yamaha Music Europe GmbH igazolja, hogy a [R-N803D] típusú
rádióberendezés megfelel a 2014/53/EU irányelvnek.
Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a
következő internetes címen:
https://europe.yamaha.com/en/support/compliance/doc.html
70 En
PL Polish
UPROSZCZONA DEKLARACJA ZGODNOŚCI UE
Yamaha Music Europe GmbH niniejszym oświadcza, że typ
urządzenia radiowego [R-N803D] jest zgodny z dyrektywą 2014/
53/UE. Pełny tekst deklaracji zgodności UE jest dostępny pod
następującym adresem internetowym:
https://europe.yamaha.com/en/support/compliance/doc.html
PT Portuguese
DECLARAÇÃO UE DE CONFORMIDADE SIMPLIFICADA
O(a) abaixo assinado(a) Yamaha Music Europe GmbH declara
que o presente tipo de equipamento de rádio [R-N803D] está em
conformidade com a Diretiva 2014/53/UE. O texto integral da
declaração de conformidade está disponível no seguinte endereço
de Internet:
https://europe.yamaha.com/en/support/compliance/doc.html
RO Romanian
DECLARAȚIA UE DE CONFORMITATE SIMPLIFICATĂ
Prin prezenta, Yamaha Music Europe GmbH declară că tipul de
echipamente radio [R-N803D] este în conformitate cu Directiva
2014/53/UE. Textul integral al declarației UE de conformitate este
disponibil la următoarea adresă internet:
https://europe.yamaha.com/en/support/compliance/doc.html
SK Slovak
ZJEDNODUŠENÉ EÚ VYHLÁSENIE O ZHODE
Yamaha Music Europe GmbH týmto vyhlasuje, že rádiové
zariadenie typu [R-N803D] je v súlade so smernicou 2014/53/EÚ.
Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej
adrese:
https://europe.yamaha.com/en/support/compliance/doc.html
SL Slovenian
POENOSTAVLJENA IZJAVA EU O SKLADNOSTI
Yamaha Music Europe GmbH potrjuje, da je tip radijske opreme
[R-N803D] skladen z Direktivo 2014/53/EU.
Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem
spletnem naslovu:
https://europe.yamaha.com/en/support/compliance/doc.html
FI Finnish
YKSINKERTAISTETTU EU-
VAATIMUSTENMUKAISUUSVAKUUTUS
Yamaha Music Europe GmbH vakuuttaa, että radiolaitetyyppi
[R-N803D] on direktiivin 2014/53/EU mukainen.
EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on
saatavilla seuraavassa internetosoitteessa:
https://europe.yamaha.com/en/support/compliance/doc.html
TR Turkey
BASİTLEŞTİRİLMİŞ AVRUPA BİRLİĞİ UYGUNLUK BİLDİRİMİ
İşbu belge ile, Yamaha Music Europe GmbH, radyo cihaz tipinin
[R-N803D], Direktif 2014/53/AB'ye uygunluğunu beyan eder. AB
uyumu beyanının tam metni aşağıdaki internet adresinden
edinilebilir:
https://europe.yamaha.com/en/support/compliance/doc.html
Published 06/2017 AM-A0
© 2017 Yamaha Corporation
Manual Development Group
Yamaha Downloads
http://download.yamaha.com/
Yamaha Global Site
https://www.yamaha.com/
AV16-0039
10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650 Japan

Documenttranscriptie

G Network Receiver Owner's Manual • The R-N803 and R-N803D network receivers allow you to play back sound in high-quality stereo at your own home. • This manual explains preparations and operations for everyday users of the unit. EN English PRECAUTIONS PLEASE READ CAREFULLY BEFORE USE. BE SURE TO FOLLOW THESE INSTRUCTIONS. The precautions listed below are to prevent risk of harm to the user and others, as well as to prevent property damage, and to help the user use this unit properly and safely. Be sure to follow these instructions. After reading this manual, be sure to keep it in a safe place where it can be referenced at any time. • Be sure to request inspections or repairs from the dealer where you purchased the unit or from qualified Yamaha service personnel. • Yamaha cannot be held responsible for damage caused by improper use or modifications to the unit. • This product is for ordinary homes. Do not use for applications requiring high reliability, such as managing lives, health care or high-value assets. WARNING This content indicates “risk of serious injury or death.” ■ Power supply/power cord ■ Water warning • Do not expose the unit to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. A liquid such as water getting into the unit may cause a fire, electric shocks, or malfunctions. If any liquid such as water seeps into the device, turn off the power immediately and unplug the power cord from the AC outlet. Then, request an inspection from the dealer where you purchased the unit or from qualified Yamaha service personnel. • Never insert or remove an electric plug with wet hands. Do not handle this unit with wet hands. Failure to observe this may cause electric shocks or malfunctions. ■ Fire warning • Do not place any burning items or open flames near the unit, since they may cause a fire. • Do not do anything that could damage the power cord. - Do not place it near a heater. - Do not bend it excessively or alter it. - Do not scratch it. - Do not place it under a heavy object. Using the power cord with the core of the cord exposed could cause electric shocks or a fire. • Do not touch the power plug or cord if there is a chance of lightning. Failure to observe this may cause electric shocks. • Use this unit with the power supply voltage printed on it. Failure to connect to an appropriate AC outlet may cause a fire, electric shocks, or malfunctions. • Be sure to use the supplied power cord. Also, do not use the supplied power cord for other units. Failure to observe the above may cause a fire, burns, or malfunctions. • Check the electric plug periodically and remove any dirt or dust which may have accumulated on it. Failure to observe this may cause a fire or electric shocks. • When setting up the unit, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the AC outlet. Even when the power switch is turned off, as long as the power cord is not unplugged from the wall AC outlet, the unit will not be disconnected from the power source. • If you hear thunder or suspect approaching lightning, quickly turn off the power switch and pull the power plug from the AC outlet. Failure to observe this may cause a fire or malfunctions. • If not using the unit for long periods of time, be sure to pull the power plug from the AC outlet. Failure to observe this may cause a fire or malfunctions. ■ Maintenance and care ■ Do not disassemble ■ If you notice any abnormality • Do not disassemble or modify this unit. Failure to observe this may cause a fire, electric shocks, injury, or malfunctions. If you notice any irregularities, be sure to request an inspection or repair from the dealer where you purchased the unit or from qualified Yamaha service personnel. • If any of the following abnormalities occur, immediately turn off the power and disconnect the power plug. If you are using batteries, remove the batteries from this unit. - The power cord/plug is damaged. - An unusual smell or smoke is emitted from the unit. - Foreign material gets into the interior of the unit. i En • Do not use aerosols or spray-type chemicals that contain combustible gas for cleaning or lubrication. The combustible gas will remain inside the unit, which may cause explosion or fire. ■ Battery use • Do not disassemble a battery. If the contents of the battery get on your hands or in your eyes, it can cause blindness or chemical burns. • Do not dispose of batteries in fire. Doing so may result in the battery bursting, causing a fire or injury. • Do not expose a battery to high temperatures, such as direct sunlight or a fire. The battery may burst, causing a fire or injury. • Do not attempt to recharge batteries that are not intended to be charged. Charging could cause the battery to burst or leak, which can cause blindness, chemical burns, or injury. • If the batteries do leak, avoid contact with the leaked fluid. If the battery fluid should come in contact with your eyes, mouth, or skin, wash immediately with water and consult a doctor. Battery fluid is corrosive and may possibly cause loss of sight or chemical burns. ■ Wireless unit • Do not use this unit near medical devices or inside medical facilities. Radio waves from this unit may affect electromedical devices. • Do not use this unit within 15 cm (6 in) of persons with a heart pacemaker implant or a defibrillator implant. Radio waves from this unit may affect electro-medical devices, such as a heart pacemaker implant or defibrillator implant. PRECAUTIONS CAUTION ■ Hearing loss • Do not use the unit/speakers or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. • Before connecting the unit to other devices, turn off the power for all devices. Also, before turning the power of all devices on or off, make sure that all volume levels are set to the minimum. Failing to do so may result in hearing loss, electric shock, or device damage. • When turning on the AC power in your audio system, always turn on the unit LAST, to avoid hearing loss and speaker damage. When turning the power off the unit should be turned off FIRST for the same reason. Failure to observe the above may cause hearing impairment or speaker damage. This content indicates “risk of injury.” ■ Maintenance ■ Power supply/power cord • Remove the power plug from the AC outlet when cleaning the unit. Failure to observe this may cause electric shocks. • Do not use an AC outlet where the power plug fits loosely when inserted. Failure to observe this may cause a fire, electric shocks, or burns. • When removing the electric plug from the unit or an AC outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it and cause electric shocks or a fire. • Insert the power plug firmly all the way into the AC outlet. Using the unit when it is not plugged in sufficiently can cause dust to accumulate on the plug, causing a fire or burns. ■ Installation • Do not place the unit in an unstable position where it might accidentally drop or fall over and cause injuries. • Do not block this unit's ventilation holes (cooling slits). This unit has ventilation holes on the top/bottom to prevent the internal temperature from becoming too high. Failure to observe this may trap heat inside the unit, causing a fire or malfunctions. • When installing this unit: - Do not cover it with any cloth. - Do not install it on a carpet or rug. - Make sure the top surface faces up; do not install on its sides or upside down. - Do not use the device in a confined, poorly-ventilated location. Failure to observe the above may trap heat inside the unit, causing a fire or malfunctions. Ensure that there is adequate space around the unit: at least 30 cm (11-3/4 in) on top, 20 cm (7-7/8 in) on the sides, and 20 cm (7-7/8 in) on the rear. • Ensure that the top is facing upwards. Failure to observe this may cause malfunctions or for the unit to fall and cause injury. • Do not place the unit in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction. • Avoid being near the unit during a disaster, such as an earthquake. Since the unit may turn over or fall and cause injury, quickly move away from the unit and go to a safe place. • Before moving this unit, be sure to turn off the power switch and disconnect all connection cables. Failure to observe this may damage the cables or cause you or someone else to trip and fall. • When transporting or moving the unit always use two or more people. Attempting to lift the unit by yourself may damage your back, result in other injury, or cause damage to the unit itself. ■ Handling caution • Do not insert foreign materials such as metal or paper into the ventilation holes of this unit. Failure to observe this may cause a fire, electric shocks, or malfunctions. If foreign material gets into the unit, immediately shut off the power and pull the power plug from the AC outlet / then turn off any amplifiers and receivers and request an inspection from the dealer where you purchased the unit or from qualified Yamaha service personnel. • Do not rest your weight on the unit or place heavy objects on it. Avoid applying excessive force to the buttons, switches or connectors. Failure to observe the above may cause injury or unit damage. • Avoid pulling the connected cables to prevent injuries or damage to the unit by causing it to fall. ■ Battery use • Always replace all batteries at the same time. Do not use new batteries together with old ones. Using new ones with old ones could cause a fire, burns, or inflammation due to fluid leaks. • Do not mix battery types, such as alkaline batteries with manganese batteries, or batteries from different makers, or different types of batteries from the same maker, since this can cause a fire, burns, or inflammation due to fluid leaks. • Keep batteries away from children. A child could accidentally swallow a battery. Failure to observe this may also cause inflammation due to battery fluid leaks. • Do not put in a pocket or bag, carry, or store batteries together with pieces of metal. The battery could short, burst, or leak, causing a fire or injury. • Always make sure all batteries are inserted in conformity with the +/- polarity markings. Failure to do so might result in a fire, burns, or inflammation due to fluid leaks. • When the batteries run out, or if the unit is not to be used for a long time remove the batteries from the remote control to prevent possible leakage of the battery fluid. • When storing or discarding batteries, insulate the terminal area by applying tape, or some other protection. Mixing them with other batteries or metal objects can cause a fire, burns, or inflammation due to fluid. Caution Do not touch the surface marked with this label. The surface may become hot during operation. ii En English - There is a loss of sound during use. - There is a crack or damage in the unit. Continued use could cause electric shocks, a fire, or malfunctions. Immediately request an inspection or repair from the dealer where you purchased the unit or from qualified Yamaha service personnel. • Be careful not to drop or apply strong impact to this unit. If you suspect the unit may have been damaged due to dropping or impact, immediately turn off the power and pull the power plug from the AC outlet. Failure to observe this may cause electric shocks, a fire, or malfunctions. Immediately request an inspection from the dealer where you purchased the unit or from qualified Yamaha service personnel. Notice and Information Notice Information Indicates points that you must observe in order to prevent product failure, damage or malfunction and data loss, as well as to protect the environment. Indicates information of note regarding this product. ■ Power • The illustrations and screens in this manual are for instructional purposes only. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. • Software may be revised and updated without prior notice. • Information marked by the “ WARNING” icon indicates points that may lead to death or serious injury if not observed. • Information marked with the “ CAUTION” icon indicates points that may lead to injury if not observed. • Information in the “Notice” sections indicates points that you must observe to prevent product failure, damage or malfunction and data loss. • Information listed in the “Note” sections indicates supplementary information. • This manual describes the “iPhone”, “iPad” and “iPod touch” collectively as the “iPhone”. (“iPhone” refers to the “iPhone”, “iPad” and “iPod touch”, unless otherwise specified.) • In this manual, illustrations of English menu screens are used as examples. • If not using the unit for a long period of time, be sure to pull the power plug from the outlet. Even if the A (Standby/On) switch has been turned off, a minute current is still flowing. ■ Installation • Do not use this unit in the vicinity of other electronic equipment, such as a TV, radio, AV unit, or mobile phone. Failure to observe this may cause this unit or the TV or radio to produce noise. • Do not use this unit in a location that is exposed to direct sunlight (such as a vehicle interior), that becomes extremely hot, such as near a heater, or extremely cold, or that is subject to excessive dust or vibration. Failure to observe this may cause the unit's panel to become deformed, the internal components to malfunction, or for operation to become unstable. • Install this unit as far away from other electronic equipment as possible. Digital signals from this unit may interfere with other electronic equipment. • If using a wireless function, avoid installing this unit near metal walls or desks, microwave ovens, or other wireless devices. ■ Connections • If connecting external units, be sure to thoroughly read the manual for each unit and connect them in accordance with the instructions. Failure to properly handle a unit in accordance with the instructions could cause malfunctions. • Do not connect this unit to industrial units. Digital audio interface standards for consumer use and industrial use are different. This unit has been designed to connect to a consumeruse digital audio interface. Connections to an industrial-use digital audio interface could not only cause this unit to malfunction, but could also damage the speakers. ■ Handling • Do not place vinyl, plastic, or rubber products on this unit. Failure to observe this may cause discoloration or deformation in the panel of this unit. • If the ambient temperature changes drastically (such as during unit transportation or under rapid heating or cooling) and there is a chance condensation may have formed in the unit, leave the unit for several hours without turning on the power until it is completely dry before use. Using the unit while there is condensation can cause malfunctions. ■ Maintenance • When cleaning the unit, use a dry, soft cloth. Using chemicals such as benzine or thinner, cleaning agents, or chemical scrubbing cloths can cause discoloration or deformation. ■ Batteries • Be sure to discard used batteries in accordance with local regulations. iii En ■ About content in this manual Contents Front panel ..................................................................... 4 Front display .................................................................. 6 Rear panel ...................................................................... 7 Remote control............................................................... 8 PREPARATION Connections ............................................................... 10 Connecting audio devices ............................................ 10 Connecting the speakers .............................................. 11 Connecting the FM/AM antennas (R-N803) ............... 13 Connecting the DAB/FM antenna (R-N803D)............ 13 Connecting the network cable ..................................... 14 Preparing a wireless antenna ....................................... 14 Connecting the power cord.......................................... 14 Turning on the unit ...................................................... 14 Connecting to network ............................................. 15 Sharing the iOS device setting..................................... 16 Configuring with the router's WPS push button .......... 17 Set the wireless network connection manually............ 18 Connecting a mobile device to the unit directly (Wireless Direct) ..................................................... 19 Verify the network connection status .......................... 20 Configuring MusicCast................................................ 20 BASIC OPERATION Playback .................................................................... 22 Playing a source........................................................... 22 Switching information on the front display ................. 22 Front panel operations ................................................. 23 Using the sleep timer ................................................... 24 Listening to FM/AM radio....................................... 25 FM/AM tuning............................................................. 25 Registering favorite radio stations (presets) ................ 25 Radio Data System tuning (U.K. and Europe models only)............................... 28 Listening to DAB radio (R-N803D)......................... 29 Preparing the DAB tuning ........................................... 29 Selecting a DAB radio station for reception................ 29 Using preset function................................................... 30 Displaying the DAB information................................. 31 Checking reception strength of each DAB channel label ......................................................................... 31 Registering the current playback song/station (Preset function) ....................................................41 Registering to a preset ................................................. 41 Recalling a preset......................................................... 41 Clearing a preset .......................................................... 41 ADVANCED OPERATION Optimizing the speaker settings automatically (YPAO)...................................................................42 Error messages............................................................. 44 Warning messages ....................................................... 45 Configuring playback settings for different playback sources (Option menu) .........................46 PREPARATION Supplied accessories ................................................... 3 Controls and functions ............................................... 4 Connecting a USB storage device ............................... 39 Playback of USB storage device contents ................... 39 Option menu items....................................................... 46 Configuring various functions (Setup menu) .........47 Setup menu items......................................................... 48 Network ....................................................................... 48 Bluetooth ..................................................................... 50 YPAO .......................................................................... 50 Volume ........................................................................ 50 AutoPowerStdby (Auto Power Standby)..................... 51 ECO Mode ................................................................... 51 BASIC OPERATION Sources that can be played back on this unit ................. 2 Configuring the system settings (ADVANCED SETUP menu)...............................52 ADVANCED SETUP menu items .............................. 52 Checking the firmware version (VERSION)............... 52 Changing the speaker impedance setting (SP IMP.) ... 52 Selecting the remote control ID (REMOTE ID).......... 52 Setting tuner frequency step (TU) ............................... 53 Restoring the default settings (INIT)........................... 53 Updating the firmware (UPDATE) ............................. 53 ADVANCED OPERATION What you can do with this unit ................................. 2 Playing back music stored on a USB storage device ......................................................................39 Updating the unit’s firmware via the network .......54 ADDITIONAL INFORMATION Troubleshooting.........................................................55 Error indications on the front display.....................61 Supported devices and file formats .........................62 Supported devices........................................................ 62 Supported file formats ................................................. 62 Trademarks ...............................................................63 Specifications .............................................................64 Index ...........................................................................66 ADDITIONAL INFORMATION INTRODUCTION INTRODUCTION Contents Playing back music via Bluetooth............................ 32 English Connecting a Bluetooth device (pairing) ..................... 32 Playing back Bluetooth device contents ...................... 32 Disconnecting a Bluetooth connection ........................ 33 Playing back music stored on media servers (PCs/NAS) ............................................................. 34 Setting the media sharing of music files...................... 34 Playback of PC music contents.................................... 35 Listening to Internet radio....................................... 37 Playing back iPhone/iTunes music via a network (AirPlay) ................................................................ 38 Playback of iPhone/iTunes music contents ................. 38 1 En INTRODUCTION What you can do with this unit This unit is a network receiver compatible with a network source such as a media server and mobile device. It supports playback from not only audio sources such as a CD player or radio, but also from Bluetooth devices and network streaming services. Sources that can be played back on this unit 1 Internet 2 Streaming service Modem PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES Router* SPEAKERS A B -30dB USB RETURN 5V CONNECT 1A YPAO MIC L R 3 PC 5 AirPlay (iTunes) This unit Mobile device 4 NAS 5 AirPlay 7 USB device 8 CD player, etc. 9 Radio (iPhone/iPad/iPod touch) 6 Bluetooth * You need a commercially available wireless router (access point) when you use a mobile device. 1 Play back the Internet radio (p. 37) 2 Play back the streaming service (see the supplement for each service.) 3 Play back music files stored on your PC (p. 34) 4 Play back music files stored on your NAS (p. 34) 6 Play back audio content from Bluetooth devices (p. 32) 7 Play back music files stored on your USB device (p. 39) 8 Play back your external component (p. 10) 9 Listening to radio (p. 25, 29) 5 Play back music files stored on your iPod/ iTunes with AirPlay (p. 38) Note For details on connecting the external devices, see “Connections” (p. 10). 2 En Supplied accessories Check that the following accessories are supplied with the product. AM antenna (R-N803) FM antenna (R-N803) * Batteries (x2) (AA, R6, UM-3) DAB/FM antenna (R-N803D) One of the above is supplied depending on the region of purchase. YPAO microphone Power cord * The supplied power cord varies depending on the region of purchase. R-N803/R-N803D Owner’s Manual CD-ROM (Europe model) R-N803/R-N803D Owner’s Manual (except Europe model) R-N803D Quick Start Guide (Europe model) G Network Receiver G Network Receiver Réseau Ampli-Tuner Сетевой ресивер ■ ■ ■ ■ English Remote control INTRODUCTION Supplied accessories 3 En Controls and functions Front panel 12 3 4 5 6 7 8 9 : A B C PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES SPEAKERS A B -30dB USB RETURN 5V CONNECT 1A YPAO MIC L 1 A (power) Turns on/off the unit. 2 Power indicator Brightly lit: Power is on Dimly lit: Standby mode Tuned off: Power is off Note When not using this unit for an extended period of time, be sure to unplug it from the power outlet. This unit uses a minimal amount of power even in standby mode. 3 Remote control sensor Receives infrared signals from the remote control. 4 DIMMER Changes the brightness level of the front display. Choose brightness from 5 levels by pressing this button repeatedly. R 7 MEMORY Registers the current radio station as a preset when TUNER is selected as the input source (p. 25, 30). Registers the current playback song or streaming station as a preset when NET or USB is selected as the input source (p. 41). 8 CLEAR Clears a preset radio station when TUNER is selected as the input source (p. 27, 30). Clears a preset song or a preset streaming station when NET or USB is selected as the input source (p. 41). 9 BAND Sets the radio tuner band when TUNER is selected as the input source. (p. 25, 29) 0 Front display Shows information about the operational status of this unit (p. 6). 5 DISPLAY Selects the information displayed on the front display (p. 22). A PRESET j / i Recalls a preset radio station (p. 27, 30) or song/streaming station (p. 41). 6 MODE Sets the FM band reception mode to automatic stereo or monaural (p. 25). B TUNING jj / ii Selects the tuning frequency (p. 25) or a DAB radio station (p. 29) when TUNER is selected as the input source. C PURE DIRECT and indicator Allows you to listen to a source in the purest possible sound (p. 23). The indicator above it lights up and the front display turns off when this function is turned on. 4 En INTRODUCTION Controls and functions PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES SPEAKERS A B -30dB USB RETURN 5V CONNECT 1A YPAO MIC L D E F G H I J D PHONES jack Outputs audio to your headphones for private listening. E YPAO MIC jack For connecting the supplied YPAO microphone (p. 42). F SPEAKERS A/B Turns on or off the speaker set connected to the SPEAKERS A and/or SPEAKERS B terminals on the rear panel each time the corresponding button is pressed. R K L M N O L LOUDNESS control Retains a full tonal range at any volume level (p. 24). Note The LOUDNESS control does not function when the YPAO Volume function (p. 50) is enabled. M SELECT/ENTER Turn the dial to select a numeric value or setting, and press the dial to confirm. G USB jack For connecting a USB storage device (p. 39). N RETURN Returns to the previous indication of the front display. H INPUT selector Selects the input source you want to listen to. CONNECT Use to register this unit to the MusicCast network (p. 20). I BASS control Increases or decreases the low frequency response. The center position produces a flat response (p. 23). O VOLUME control Increases or decreases the sound output level. J TREBLE control Increases or decreases the high frequency response. The center position produces a flat response (p. 23). English K BALANCE control Adjusts the sound output balance of the left and right speakers to compensate for sound imbalances caused by speaker locations or listening room conditions (p. 23). 5 En Controls and functions Front display 1 2 3 4 5 6 78 STEREO TUNED SLEEP YPAO VOL. A 9 B VOL. MUTE L R SW : : A B Note • If you turn on the power to the unit right after you purchase or initialize it, the unit will display “WAC” (Wireless Accessory Configuration) on the front display and trigger an automatic iOS device search. See “Sharing the iOS device setting” (p. 16) for details on the iOS device and network connection. • You can change the brightness level of the front display by pressing DIMMER on the front panel (p. 4). 1 Information display Displays the current status (such as input name). You can switch the information that is displayed when you press DISPLAY on the front panel (p. 22). 2 Bluetooth indicator Lights up when the unit is connecting to a Bluetooth device. 3 Signal strength indicator Lights up when the unit connects to a wireless network or operates as an access point. The strength of the wireless network signal can be verified by the indicator status. 4 SLEEP indicator Lights up when the sleep timer is on (p. 24). 5 STEREO indicator Lights up when the unit is receiving a stereo FM radio signal. 6 TUNED indicator Lights up when the unit is receiving an FM/AM radio station signal. 6 En 7 YPAO VOL. indicator Lights up when the YPAO volume (p. 50) function is enabled. The YPAO volume function is automatically enabled after YPAO is performed. 8 A/B indicators “A” lights up when the SPEAKERS A output is enabled and “B” lights up when the SPEAKERS B output is enabled. 9 Volume indicator Indicates the current volume. 0 Cursor indicators Indicate the remote control cursor keys currently operational. A Speaker indicators Indicate the speakers from which signals are output during YPAO. A Front speaker (L) S Front speaker (R) L Subwoofer B MUTE indicator Blinks when audio is muted. Controls and functions Rear panel 2 3 4 5 6 7 8 INTRODUCTION 1 NETWORK AC IN IN 1 1 IN 2 1 OPTICAL 2 2 COAXIAL ANTENNA OUT SPEAKERS FM AM IN PHONO A GND 3 75Ω OUT B LINE CD 12V 9 : TRIGGER SUBWOOFER OUT OUT 0.1A AB C (R-N803) 1 LINE 1-3 jacks For connecting to analog audio components (p. 10). 8 AC IN jack For connecting the supplied power cord (p. 14). 2 PHONO jacks For connecting to a turntable (p. 10). 9 CD jacks For connecting to a CD player, etc. (p. 10). 3 OPTICAL 1/2 jacks For connecting to audio components equipped with optical digital output (p. 10). 0 ANTENNA terminals For connecting to the radio antennas (p. 13). 4 COAXIAL 1/2 jacks For connecting to audio components equipped with a coaxial digital output (p. 10). A TRIGGER OUT jacks For connecting to a subwoofer that supports the trigger function (p. 10). 5 NETWORK jack For connecting to a network with a network cable (p. 14). B SUBWOOFER OUT jack For connecting to a subwoofer with built-in amplifier (p. 10). 6 Wireless antenna For connecting to a network device wirelessly (p. 14). C SPEAKERS terminals For connecting to speakers (p. 10). English 7 VOLTAGE SELECTOR (General models only) Selects the switch position according to your local voltage (p. 14). 7 En Controls and functions Remote control 1 Infrared signal transmitter 1 Sends infrared signals. 2 SPEAKERS A/B 2 SPEAKERS A A B PHONO SLEEP COAX 1 COAX 2 3 OPT 2 CD LINE 1 LINE 2 LINE 3 TUNER NET USB BAND 5 MEMORY 3 Input selection keys BLUETOOTH OPT 1 4 B Turns on and off the set of speakers connected to the SPEAKERS A and/or SPEAKERS B terminals on the rear panel of this unit when the corresponding key is pressed. Select an input source for playback. PHONO PHONO jacks COAX 1/2 COAXIAL1/2 jacks BLUETOOTH Bluetooth connection OPT 1/2 OPTICAL 1/2 jacks CD CD jacks LINE 1-3 LINE 1-3 jacks TUNER (R-N803) FM/AM tuner (R-N803D) FM/DAB tuner NET Network source (press repeatedly to select a desired network source) USB USB jack (on the front panel) TUNING PRESET 4 Radio keys 6 7 8 9 Operate the radio. BAND Sets the radio tuner band when TUNER is selected as the input source. (p. 25, 29) TUNING jj/ii Selects the tuning frequency (p. 25) or a DAB radio station (p. 29) when TUNER is selected as the input source. ENTER HOME RETURN SETUP OPTION VOLUME NOW PLAYING MUTE REPEAT SHUFFLE C D 5 Preset keys MEMORY 0 E PRESET j/i Registers the current radio station as a preset when TUNER is selected as the input source (p. 25, 30). Registers the current playback song or streaming station as a preset when NET or USB is selected as the input source (p. 41). Recalls a preset radio station (p. 27, 30) or song/streaming station (p. 41). 6 Menu operation keys Cursor keys (B/C/D/E) ENTER RETURN Select menus and parameters, etc. Confirms a selected item. Returns to the previous state. 7 HOME Moves up top level when selecting music files, folders, etc. 8 SETUP Displays the “Setup” menu (p. 47). 9 NOW PLAYING Displays music information when selecting music files, folders, etc. 0 VOLUME +/Adjust the volume. 8 En Controls and functions A A (power) ■ Installing batteries Turns on/off (standby) the unit. INTRODUCTION Note The A (power) key on the remote control works only when the A (power) on the front panel is on. B SLEEP Sets the sleep timer (p. 24). C OPTION D MUTE Mutes the audio output. E Playback keys Let you play back and perform other operations for network sources, Bluetooth devices and USB devices. Note The playback keys may not work depending on the Bluetooth device. Note • Change all batteries if the operation range of the remote control narrows. • Before inserting new batteries, wipe the compartment clean. ■ Operation range The remote controls transmit a directional infrared beam. Be sure to aim the remote controls directly at the remote control sensor on the front panel of this unit. Approximately 6 m (20 ft) 30° 30° Remote control English Displays the “Option” menu (p. 46). 9 En PREPARATION Connections Connecting audio devices Make sure to connect L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Refer to the owner’s manual for each of your components. Make sure to use RCA cables, optical cables, or coaxial cables to connect audio components. CAUTION • Do not connect this unit or other components to the main power until all connections between components are complete. • Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers. DVD player, etc. Turntable O Audio output CD player, etc. Audio output (digital optical) C Audio output (digital coaxial) GND NETWORK IN 1 1 IN 2 1 OPTICAL 2 2 COAXIAL ANTENNA OUT FM SPEAKERS AM IN PHONO A GND 3 75Ω OUT B LINE CD 12V 0.1A TRIGGER SUBWOOFER OUT OUT System connection Audio output Audio input CD recorder, etc. Audio output CD player, etc. Subwoofer Speakers A Only PCM signals can be input to the digital (OPTICAL/COAXIAL) jacks of this unit. 10 En Speakers B Connections Connecting the speakers CAUTION Connect the speakers with impedance as shown below. If you connect speakers with an excessively low impedance, this unit may overheat. You can change the speaker impedance setting of this unit in “SP. IMP” (p. 52) in the ADVANCED SETUP menu. Speaker impedance (SP IMP.) 4 MIN 8 MIN (Default) SPEAKERS A or SPEAKERS B 4 Ω or higher 8 Ω or higher SPEAKERS A and SPEAKERS B 8 Ω or higher 16 Ω or higher Bi-wire connection 4 Ω or higher 8 Ω or higher PREPARATION Speaker connection ■ Connecting speaker cables Speaker cables have two wires. One is for connecting the negative (–) terminal of the unit and the speaker, and the other is for the positive (+) terminal. If the wires are colored to prevent confusion, connect the black wire to the negative and the other wire to the positive terminal. a Remove approximately 10 mm (3/8”) of insulation from the ends of the speaker cable and twist the bare wires of the cable firmly together. b Loosen the speaker terminal. c Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the terminal. d Tighten the terminal. 10 mm (3/8") a b c d Note When inserting speaker cables into the speaker terminals, insert only the bare speaker wire. If insulated cable is inserted, the connection may be poor and sound may not be heard. ■ Connecting via banana plug (North America, Australia, General models only) Tighten the knob and then insert the banana plug into the end of the corresponding terminal. Banana plug 11 En English Note • Do not bundle audio cables and speaker cables together with the power cable. Doing so may generate noise. • The PHONO jacks are designed for connecting a turntable with an MM cartridge. • Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise without the GND connection. • If you have a Yamaha subwoofer that supports a system connection, you can switch the power of the subwoofer in conjunction with tuning on/off this unit by connecting the subwoofer to the TRIGGER OUT jack with a monaural miniplug cable. • In order to prevent the audio signal from looping when an audio recording device is connected, the audio signal is not output from the LINE 2 (OUT) jacks when LINE 2 is selected. Similarly, the audio signal is not output from the LINE 3 (OUT) jacks when LINE 3 is selected. Connections ■ Bi-wire connection Bi-wire connection separates the woofer from the combined midrange and tweeter section. A bi-wire compatible speaker has four binding post terminals. These two sets of terminals allow the speaker to be split into two independent sections. With these connections, the mid and high frequency drivers are connected to one set of terminals and the low frequency driver to another set of terminals. This unit SPEAK Speaker A B Connect the other speaker to the other set of terminals in the same way. Note • When making bi-wire connections, remove the shorting bridges or cables on the speaker. Refer to the speakers’ instruction manuals for more information. • To use the bi-wire connections, press SPEAKERS A and SPEAKERS B on the front panel or on the remote control so that both “A” and “B” indicators light up on the front display. PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES SPEAKERS A B -30dB USB RETURN 5V CONNECT 1A YPAO MIC L R SPEAKERS A/B SPEAKERS A/B SPEAKERS A B PHONO SLEEP COAX 1 COAX 2 OPT 1 12 En OPT 2 BLUETOOTH CD Connections Connecting the FM/AM antennas (R-N803) Connecting the DAB/FM antenna (R-N803D) Connect the supplied FM/AM antenna to this unit. Fix the end of the FM antenna to a wall, and place the AM antenna. Connect the supplied DAB/FM antenna to this unit and fix the antenna ends to a wall. AM antenna DAB/FM antenna PREPARATION FM antenna 1 2 1 OPTICAL 1 2 FM 1 2 COAXIAL ANTENNA ANTENNA PHONO 2 OPTICAL COAXIAL FM DAB FM AM PHONO GND AM GND 75Ω 75Ω Note Note • If you experience poor reception quality, install an outdoor antenna. • Unwind only the length of cable needed from the AM antenna unit. • The wires of the AM antenna have no polarity. • If you experience poor reception quality, install an outdoor antenna. • The antenna should be stretched out horizontally. ■ Assembling the supplied AM antenna English ■ Connecting the wires of the AM antenna 2 Insert 1 Hold down 13 En Connections Connecting the network cable Connecting the power cord Connect the unit to your router with a commerciallyavailable STP network cable (CAT-5 or higher straight cable). After all the connections are complete, connect the supplied power cord to this unit and then to an AC wall outlet. Note WARNING Use an STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. Internet Network Attached Storage (NAS) (General model only) Before connecting the power cord, make sure you set VOLTAGE SELECTOR of this unit according to your local voltage. Improper setting of VOLTAGE SELECTOR may cause fire and damage to this unit. WAN LAN AC IN Modem Router VOLTAGE SELECTOR 110 –120 V PC To the AC wall outlet with the power cord 220 –240 V Network cable Mobile device (such as iPhone) Turning on the unit NETWORK AC IN Press A (power) on the front panel to turn on the unit. • SPEAKERS A (power) A This unit (rear) (R-N803) Preparing a wireless antenna If you use a wireless network connection or a Bluetooth connection, erect the wireless antenna. For information on how to connect the unit to a wireless network, see “Connecting to network” (p. 15). For information on using this unit with a Bluetooth device, see “Playing back music via Bluetooth” (p. 32). ORK NETW Notice Do not apply excessive force on the wireless antenna. Doing so may damage the antenna. 14 En Connecting to network Connecting to network There are several methods to connect the unit to a network. Select a connection method according to your environment. Note WAC (Wireless Accessory Configuration) If you turn on the power to the unit right after you purchase or initialize it, the unit will automatically use the network settings of the iOS device (iPhone/iPad/iPod touch) and try to connect to a wireless LAN (unless the unit is already connected to a wired LAN). WAC R-N803 XXXXXX If you have an iOS device, follow the procedure from Step 6 in “Sharing the iOS device setting” (p. 16). If you plan to connect the unit wirelessly by another method, press RETURN to exit the current screen, and then proceed to one of the sections below. PREPARATION • Some security software installed on your PC or the firewall settings of network devices (such as a router) may block the access of the unit to the network devices or the Internet. In these cases, configure the security software or firewall settings appropriately. • Each server must be connected to the same subnet as the unit. • To use the service via the Internet, broadband connection is strongly recommended. • When playing a high-resolution audio source via the network, we recommend connecting with a wired router for stable playback. ■ Connecting with a wireless router (access point) Connect to the network with the method listed below that corresponds to your environment. Register this unit to the MusicCast network and make the wireless network connection at once (p. 20) Connecting using the Wi-Fi setting of the iOS device (iPhone/iPad/iPod touch) Share the Wi-Fi setting of the iOS device (p. 16) Connecting using WPS push button configuration on the wireless router (or access point) Use the WPS push button configuration (p. 17) Connecting with a wireless router (access point) without WPS push button configuration Set the network connection manually (p. 18) English Connecting using “MusicCast CONTROLLER” 15 En Connecting to network ■ Connecting with the wired router You can connect to the network by simply making a wired LAN connection (p. 14) Connecting using the DHCP server function of the router Note • You can configure the network parameters (such as IP address) in “IP Address” (p. 49) in the “Setup” menu. • If you want to use a wired LAN connection when a wireless connection has been made, set “Connection” (p. 48) in the “Setup” menu to “Wired”. ■ Connecting without a wired router or wireless router (access point) Connecting wirelessly to a mobile device (Wireless Direct) Connect wirelessly with Wireless Direct (p. 19) Note When the unit is connected to the network with Wireless Direct, it cannot connect to any other wireless router (access point). To play back contents from the Internet or update the unit's firmware via the network, connect this unit to a network with a wired router or wireless router (access point). Sharing the iOS device setting You can easily setup a wireless connection by applying the connection settings on iOS devices (iPhone/iPad/iPod touch). Before proceeding, confirm that your iOS device is connected to a wireless router (access point). MEMORY Cursor keys B / C ENTER RETURN SETUP SETUP 3 Use the cursor keys (B / C) to select “Connection” and press ENTER. 4 Use the cursor keys (B / C) to select “Wireless” and press ENTER. 5 Use the cursor keys (B / C) to select “Share Setting” and press ENTER twice. OPTION VOLUME NOW PLAYING Use the cursor keys (B / C) to select “Network” and press ENTER. Note ENTER RETURN Press SETUP. To return to the previous state, press RETURN. PRESET HOME MUTE Note • If you set up a wireless connection with this method, all the network settings will be initialized. • This configuration does not work if the security method of your wireless router (access point) is WEP. In this case, use other connection method. 16 En 1 2 WIRELESS Share Setting SHARE Wireless(WAC) Note When connected to a wired network, “LAN CABLE” and “Pls disconnect” appears on the front display. In this case, disconnect the network cable from the unit, and press ENTER. Connecting to network 6 On the iOS device, select the unit as the AirPlay speaker in the Wi-Fi screen. Configuring with the router's WPS push button Example (iOS 10) You can easily set up a wireless connection with one push of the WPS button. Note This configuration does not work if the security method of your wireless router (access point) is WEP or WPA2-TKIP. In this case, use other connection method. Check the network currently selected and tap “Next”. Tap here to start setup PRESET Cursor keys B / C ENTER ENTER HOME RETURN RETURN SETUP SETUP OPTION VOLUME NOW PLAYING The network currently selected When the sharing process finishes, the unit is automatically connected to the selected network (access point). When the setting finishes, verify whether the unit is connected to a wireless network (p. 20). 1 2 MUTE Press SETUP. Use the cursor keys (B / C) to select “Network” and press ENTER. Note To return to the previous state, press RETURN. 3 Use the cursor keys (B / C) to select “Connection” and press ENTER. 4 Use the cursor keys (B / C) to select “Wireless” and press ENTER. WIRELESS WPS 5 Press ENTER twice. “Connecting” appears on the front display. 6 Push the WPS button on the wireless router (access point). When the connection process finishes, “Completed” appears on the front display. When the setting finishes, verify whether the unit is connected to a wireless network (p. 20). If “Not connected” appears, repeat from Step 1 or try another connection method. 7 To exit from the menu, press SETUP. English 7 MEMORY PREPARATION The name of this unit About WPS WPS (Wi-Fi Protected Setup) is a standard established by the Wi-Fi Alliance, which allows easy establishment of a wireless home network. 17 En Connecting to network Set the wireless network connection manually Before performing the following procedure, check the security method and security key on the wireless router (access point). MEMORY PRESET j / i PRESET 9 Settings None, WEP, WPA2-PSK (AES), Mixed Mode Note If you select “None”, the connection may be insecure since the communication is not encrypted. 10 Cursor keys B/C/D/E ENTER ENTER HOME SETUP OPTION VOLUME NOW PLAYING 1 2 MUTE 11 Use the cursor keys to enter the security key on the wireless router (access point), and press RETURN to previous state. If you select “WEP” in step 9, enter either 5 or 13 character string, or 10 or 26 hexadecimal digits. If you select “WPA2-PSK (AES)” or “Mixed Mode” in step 9, enter 8 to 63 character string or 64 hexadecimal digits. Use the cursor keys (D/E) to move the edit position and the cursor keys (B/C) to select a character. Press PRESET i to insert a character and PRESET j to delete. 12 Use the cursor keys (B / C) to select “Connect[ENTER]” and press ENTER to save the setting. If the wireless network connection cannot be made, the SSID or security key may be incorrect. Repeat from Step 6. You can verify whether the unit is connected to a wireless network (p. 20). 13 To exit from the menu, press SETUP. Press SETUP. Use the cursor keys (B / C) to select “Network ” and press ENTER. Note To return to the previous state, press RETURN. 3 Use the cursor keys (B / C) to select “Connection” and press ENTER. 4 Use the cursor keys (B / C) to select “Wireless” and press ENTER. 5 Use the cursor keys (B / C) to select “Manual Setting” and press ENTER. MANUAL SSID 6 Use the cursor keys (B / C) to select “SSID” and press ENTER. SSID 7 Use the cursor keys to enter the SSID on the wireless router (access point), and press RETURN to previous state. Use the cursor keys (D/E) to move the edit position and the cursor keys (B/C) to select a character. Press PRESET i to insert a character and PRESET j to delete. 8 Use the cursor keys (B / C) to select “Security” and press ENTER. SECURITY WPA2-PSK(AES) 18 En Use the cursor keys (B / C) to select “Security Key” and press ENTER. KEY RETURN RETURN SETUP Use the cursor keys (D / E) to select desired security method and press RETURN. Connecting to network Using Wireless Direct, this unit can operate as a wireless network access point that mobile devices can directly connect to. MEMORY PRESET j / i PRESET Cursor keys B/C/D/E ENTER 7 Settings None, WPA2-PSK (AES) Note • If you select “None”, proceed to Step 10. • If you select “None”, the connection may be insecure since the communication is not encrypted. 8 ENTER HOME RETURN SETUP OPTION VOLUME NOW PLAYING MUTE 9 Use the cursor keys to enter the security key on this unit, and press RETURN to previous state. Enter 8 to 63 character string or 64 hexadecimal digits. Use the cursor keys (D / E) to move the edit position and the cursor keys (B / C) to select a character. Press PRESET i to insert a character and PRESET j to delete. 10 Use the cursor keys (B / C) to select “Connect[Enter]” and press ENTER to save the setting. 11 Configure the Wi-Fi settings of a mobile device. For details on settings of your mobile device, refer to the instruction manual of the mobile device. Note When making a Wireless Direct connection, you cannot connect this unit or the mobile device to the Internet, so Internet services such as Internet radio are not available. Press SETUP. Use the cursor keys (B / C) to select “Network” and press ENTER. Note To return to the previous state, press RETURN. 3 Use the cursor keys (B / C) to select “Connection” and press ENTER. 4 Use the cursor keys (B / C) to select “WirelesDirect” and press ENTER. (1) Enable the Wi-Fi function on the mobile device. (2) Select the SSID of this unit from the list of available access points. (3) When you are prompted for a password, enter the security key displayed in Step 9. W DIRECT SSID 5 Press ENTER to check the SSID on this unit, and press RETURN to previous state. 6 Use the cursor keys (B / C) to select “Security” and press ENTER. If the Wireless Direct connection cannot be made, the security key may be incorrect. Configure the Wi-Fi settings of a mobile device again. 12 To exit from the menu, press SETUP. SECURITY WPA2-PSK(AES) English 1 2 Use the cursor keys (B / C) to select “Security Key” and press ENTER. KEY RETURN SETUP Use the cursor keys (D / E) to select desired security method and press RETURN. PREPARATION Connecting a mobile device to the unit directly (Wireless Direct) 19 En Connecting to network Verify the network connection status Configuring MusicCast Perform the following procedure to verify the unit’s connection to a network. ■ About MusicCast MEMORY Cursor keys B / C ENTER PRESET ENTER HOME RETURN RETURN SETUP SETUP OPTION VOLUME NOW PLAYING 1 2 MUTE Press SETUP. Use the cursor keys (B / C) to select “Network” and press ENTER. Note Use MusicCast to share music between MusicCastcompatible devices in multiple rooms. With the dedicated “MusicCast CONTROLLER” app, you can easily enjoy music from your smartphone, a media server (a personal computer or NAS) or Internet radio (streaming services) wherever you are in your home. • All MusicCast-compatible devices can be operated from the dedicated “MusicCast CONTROLLER” app • Multiple devices that support MusicCast in separate rooms can be linked to play music simultaneously • Supports music playback through Internet radio (streaming services) • Network settings for devices that support MusicCast Visit the following website for more information on MusicCast and on which devices are compatible. http://www.yamaha.com/musiccast/ To return to the previous state, press RETURN. Note 3 Use the cursor keys (B / C) to select “Information” and press ENTER. For details on MusicCast, download the MusicCast Setup Guide from the Yamaha Download website. http://download.yamaha.com/ 4 Use the cursor keys (B / C) to select “STATUS”. ■ MusicCast CONTROLLER STATUS Connect When “Connect” appears, the unit is connected to a network. If “Disconnect” appears, reset connection. 5 To exit from the menu, press SETUP. To use network functionality with a device that supports MusicCast, you need to use the “MusicCast CONTROLLER” dedicated app for mobile devices. Search for and install “MusicCast CONTROLLER” (free) in the App Store or on Google Play. ■ Registering to the MusicCast network Register this unit to the MusicCast network. At the same time, configure the wireless network connection settings for this unit. Note The SSID and security key for your wireless network will be needed. 1 On your mobile device, start “MusicCast CONTROLLER” and tap “Setup”. Note If you have already connected other MusicCast compatible devices to the network, tap “ ” (Settings) and then “Add New Device”. 20 En Connecting to network 2 Operate “MusicCast CONTROLLER” following the on screen instructions, then hold down CONNECT on the front panel of this unit for 5 seconds. CONNECT PREPARATION 3 Operate “MusicCast CONTROLLER” following the onscreen instructions to set up the network. This completes the MusicCast network registration and wireless network connection settings. Use “MusicCast CONTROLLER” to play back music. Note English • AirPlay and DSD sound cannot be transmitted. Music can be played back only from this unit. • When Pure Direct (p. 23) is turned on, only the network sources (such as Internet radio), Bluetooth device sources and USB storage device sources can be played via the MusicCast network. 21 En BASIC OPERATION Playback Playing a source Switching information on the front display SPEAKERS SPEAKERS A/B A A (power) B PHONO SLEEP COAX 1 COAX 2 When you select a network source or USB as the input source, you can switch playback information on the front display. BLUETOOTH OPT 1 OPT 2 CD LINE 1 LINE 2 LINE 3 Input selection keys PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES TUNER NET SPEAKERS A B USB -30dB USB RETURN 5V CONNECT 1A YPAO MIC L BAND R TUNING HOME RETURN DISPLAY SETUP OPTION VOLUME NOW PLAYING 1 2 VOLUME MUTE Press one of the input selection keys to select the input source you want to listen to. Press SPEAKERS A and/or SPEAKERS B to select speakers A and/or speakers B. When speaker set A is turned on, “SPEAKERS A:On” appears on the front display. When speaker set B is turned on, “SPEAKERS B:On” appears on the front display. 1 Press DISPLAY. Each time you press the key, the displayed item changes. INFO Track About 3 seconds later, the corresponding information for the displayed item appears. SERVER 3 4 Play the source. Press VOLUME +/– to adjust the sound output level. Note You can adjust the tonal quality by using the BASS, TREBLE, BALANCE and LOUDNESS controls or the PURE DIRECT switch on the front panel. 5 When you finish using, press A (power) on the front panel to turn off the power. When you press A (power) on the remote control, this unit set to standby mode. 22 En A Track #1 Note • When one set of speakers is connected using bi-wire connections, or when using two sets of speakers simultaneously (A and B), press SPEAKERS A and SPEAKERS B on the front panel or on the remote control so that both “A” and “B” indicators light up on the front display. • When listening with headphones, turn off the speakers. A Input source Item Bluetooth Track (song title), Artist (artist name), Album (album name) Server AirPlay USB Track (song title), Artist (artist name), Album (album name), Time Net Radio Track (song title), Album (album name), Time, Station (station name) Note “_” (underscore) will be displayed for characters not supported by the unit. Playback ■ Adjusting the BASS and TREBLE controls Front panel operations ■ Enjoying pure high fidelity sound (Pure Direct) PURE DIRECT PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES SPEAKERS A B -30dB USB RETURN 5V CONNECT 1A YPAO MIC L R Note • When the PURE DIRECT switch is turned on, the front display turns off. • The BASS, TREBLE, BALANCE, and LOUDNESS controls do not function while PURE DIRECT is turned on. DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES SPEAKERS A B -30dB USB RETURN 5V CONNECT 1A YPAO MIC L R BASS TREBLE The BASS and TREBLE controls adjust high and low frequency response. The center position produces a flat response. BASS control When you feel there is not enough bass (low frequency sound), rotate clockwise to boost. When you feel there is too much bass, rotate counterclockwise to suppress. Control range: –10 dB to +10 dB (20 Hz) TREBLE control When you feel there is not enough treble (high frequency sound), rotate clockwise to boost. When you feel there is too much treble, rotate counterclockwise to suppress. Control range: –10 dB to +10 dB (20 kHz) BASIC OPERATION PURE DIRECT switch DIMMER ■ Adjusting the BALANCE control PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES SPEAKERS A B -30dB USB RETURN 5V CONNECT 1A YPAO MIC L R BALANCE The BALANCE control adjusts the sound output balance of the left and right speakers to compensate for sound imbalance caused by speaker locations or listening room conditions. English When the PURE DIRECT switch is turned on, routes input signals from your audio sources so that the input signals bypass the BASS, TREBLE, BALANCE and LOUDNESS controls, thus eliminating any alterations to the audio signals and creating the purest possible sound. The PURE DIRECT indicator lights up and the front display turns off after a few seconds. Note If you rotate the BALANCE control to the end of L (left) or R (right), the opposite side of channel is muted. 23 En Playback ■ Adjusting the LOUDNESS control PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES SPEAKERS A B -30dB USB RETURN 5V CONNECT 1A Using the sleep timer Use this feature to automatically set this unit to standby mode after a certain amount of time. The sleep timer is useful when you are going to sleep while this unit is playing or recording a source. YPAO MIC L R LOUDNESS VOLUME SPEAKERS A Retain a full tonal range at any volume level, thus compensating for the human ears’ loss of sensitivity to high and low-frequency ranges at low volume. SLEEP Note If the PURE DIRECT switch is turned on with the LOUDNESS control set at a certain level, the input signals bypass the LOUDNESS control, resulting in a sudden increase in the sound output level. To prevent your ears or the speakers from being damaged, be sure to press the PURE DIRECT switch after lowering the sound output level or after checking that the LOUDNESS control is properly set. 1 Set the LOUDNESS control to the FLAT position. SLEEP COAX 1 COAX 2 The LOUDNESS control does not function when the YPAO Volume function (p. 50) is enabled. CAUTION A (power) B PHONO BLUETOOTH OPT 1 OPT 2 CD LINE 1 LINE 2 LINE 3 Note The sleep timer can only be set with the remote control. 1 Press SLEEP repeatedly to set the amount of time before this unit is set to standby mode. Each time you press SLEEP, the front display changes as shown below. Sleep 120 min. Sleep Off Sleep 90 min. Sleep 30 min. Sleep 60 min. The SLEEP indicator blinks while setting the amount of time for the sleep timer. SLEEP Sleep 120min. 2 3 Rotate the VOLUME control on the front panel (or press VOLUME +/– on the remote control) to set the sound output level to the loudest listening level that you would listen to. Rotate the LOUDNESS control until the desired volume is obtained. Note After setting the LOUDNESS control, enjoy listening to music at your preferred volume level. If the effect of the LOUDNESS control setting is too strong or weak, readjust the LOUDNESS control. 24 En A VOL. If the sleep timer is set, the SLEEP indicator on the front display lights up. Note • To disable the sleep timer, select “Sleep Off”. • The sleep timer setting can also be canceled by pressing A (power) to set this unit to standby mode. Listening to FM/AM radio Listening to FM/AM radio ■ Improving FM reception (FM mode) Note If the signal from the station is weak and the sound quality is not good, set the FM band reception mode to monaural mode to improve reception. R-N803D does not include an AM tuner. FM/AM tuning PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT SPEAKERS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES A BASS B SPEAKERS A B -30dB USB RETURN 5V CONNECT 1A YPAO MIC PHONO SLEEP BLUETOOTH OPT 2 CD LINE 1 LINE 2 LINE 3 TUNER NET USB MODE 1 TUNER BAND MEMORY 1 TUNING TUNING jj / ii PRESET Press TUNER to select “TUNER” as the input source. Press BAND repeatedly to select the reception band (FM or AM). 3 Press TUNING jj / ii to set a frequency. To search stations automatically, press and hold TUNING jj / ii for a second. If a broadcast is being received, “TUNED” indicator on the front display will be lit. If a stereo broadcast is being received, the “STEREO” indicator will also lit. A FM 98.50MHz Note The STEREO indicator on the front panel lights up while listening to a station in stereo mode. 2 STEREO TUNED Press MODE repeatedly to select “Stereo” (automatic stereo mode) or “Mono” (monaural mode) when this unit is tuned in to an FM radio station. When “Mono” is selected, FM broadcasts will be heard in monaural sound. VOL. Frequency Note • If the station signals are weak, tuning search does not stop at the desired station. • When FM radio reception is unstable, switching the FM mode to "Mono" may improve it. BASIC OPERATION OPT 1 BAND R Registering favorite radio stations (presets) You can register up to 40 radio stations as presets. Once you have registered stations, you can easily tune into them by selecting their preset numbers. You can automatically register FM radio stations that have strong signals (auto preset). For AM radio stations or FM radio stations with weak signals, register them manually (p. 26). ■ Registering FM radio stations automatically (auto preset) Note • When you register radio stations automatically, radio stations currently registered to preset numbers may be overwritten. • If the station you want to register is weak in signal strength, try using the manual preset tuning method. • FM stations registered as presets using the automatic preset registration feature will be heard in stereo. • (U.K. and Europe models only) Only Radio Data System broadcasting stations can be preset automatically. 25 En English COAX 1 COAX 2 L Listening to FM/AM radio LINE 1 LINE 2 LINE 3 TUNER NET USB ■ Registering a radio station manually BAND TUNING TUNER BAND MEMORY TUNING BAND MEMORY PRESET MEMORY PRESET j / i PRESET j / i PRESET ENTER Cursor keys B / C ENTER ENTER HOME RETURN RETURN HOME RETURN SETUP RETURN SETUP OPTION OPTION VOLUME NOW PLAYING MUTE 1 Press TUNER to select “TUNER” as the input source. 2 Press OPTION on the remote control. The “Option” menu is displayed (p. 46). 3 Use the cursor keys (B / C) to select “Auto Preset”, and then press ENTER. A Follow “FM/AM tuning” (p.25) to tune into the desired radio station. 2 Press MEMORY. Note By holding down MEMORY for more than 3 seconds, you can skip the following steps and automatically register the selected station to an empty preset number (i.e., the preset number following the last preset number used). READY A VOL. Auto Preset 01:FM 87.5 MHz 02:Empty Frequency Note • Before scanning begins, you can specify the first preset number to be used by pressing PRESET j / i or cursor key (B/C) on the remote control. • To cancel scanning, press BAND or RETURN. When scanning is complete, “FINISH” is displayed and then the display returns to original state. PRESET j / i to select the preset number to which the station will be registered. If you select a preset number to which no station is registered, the message “Empty” is displayed. 9850 VOL. This unit starts scanning the FM band about 5 seconds later from the lowest frequency upwards. To begin scanning immediately, hold down ENTER. 26 En 1 3 OPTION Preset number OPTION VOLUME STEREO TUNED A VOL. “Empty” (not in use) or the frequency currently registered 4 Press MEMORY. When registration is complete, the display returns to the original state. Note To cancel registration, press RETURN. Listening to FM/AM radio 4 ■ Recalling a preset station You can recall preset stations that were registered using automatic station preset or manual station preset. CLEAR B PHONO VOL. BLUETOOTH OPT 1 OPT 2 CD LINE 1 LINE 2 LINE 3 TUNER NET USB If the preset station is cleared, “Cleared” appears and then the next in-use preset number is displayed. CLEAR TUNER A VOL. 01:Cleard TUNING PRESET PRESET j / i 5 Repeat step 4 until all desired preset stations are cleared. To exit from the “Option” menu, press OPTION. 1 Press TUNER to select “TUNER” as the input source. 6 2 Press PRESET j / i to select a preset number. On the front panel BASIC OPERATION MEMORY A Preset station to be cleared SLEEP COAX 1 COAX 2 BAND STEREO TUNED 01:FM 98.50MHz SPEAKERS A Use the cursor keys (B / C) to select a preset station to be cleared and press ENTER. Note • Preset numbers to which no stations are registered are skipped. • “No Presets” is displayed if no stations are registered. ■ Clearing a preset station INPUT CLEAR PRESET j / i Clear radio stations registered to the preset numbers. On the remote control LINE 1 LINE 2 LINE 3 TUNER NET USB TUNER BAND TUNING MEMORY Cursor keys B / C ENTER PRESET SELECT/ ENTER 1 Rotate the INPUT selector to select “TUNER” as the input source. 2 3 Press CLEAR. Press PRESET j / i to select a preset station to be cleared and press CLEAR. CLEAR STEREO TUNED A 01:FM 98.50MHz ENTER VOL. Preset station to be cleared HOME RETURN SETUP OPTION MUTE 1 Press TUNER to select “TUNER” as the input source. 2 3 Press OPTION. CLEAR 01:Cleard A VOL. English NOW PLAYING If the preset station is cleared, “Cleared” appears. OPTION VOLUME Use the cursor keys to select “Clear Preset” and press ENTER. OPTION Clear Preset A VOL. 27 En Listening to FM/AM radio Radio Data System tuning (U.K. and Europe models only) Radio Data System is a data transmission system used by FM stations in many countries. The unit can receive various types of Radio Data System data, such as “Program Service”, “Program Type,” “Radio Text” and “Clock Time”, when it is tuned into a Radio Data System broadcasting station. ■ Displaying the Radio Data System information PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES SPEAKERS A B -30dB USB RETURN 5V CONNECT 1A YPAO MIC L R DISPLAY 1 Tune into the desired Radio Data System broadcasting station. Note We recommend using “Auto Preset” to tune into the Radio Data System broadcasting stations (p. 25). 2 Press DISPLAY. Each time you press the key, the displayed item changes. INFO STEREO TUNED A VOL. Program Type Item name About 3 seconds later, the corresponding information for the displayed item appears. ,9850 STEREO TUNED CLASSICS A VOL. Information Program Service Program service name Program Type Current program type Radio Text Information on the current program Clock Time Current time Frequency Frequency Note “Program Service”, “Program Type”, “Radio Text”, and “Clock Time” are not displayed if the radio station does not provide the Radio Data System service. 28 En Listening to DAB radio (R-N803D) Listening to DAB radio (R-N803D) Selecting a DAB radio station for reception You can select a DAB radio station from the stations stored by the initial scan. Note This unit supports Band III (174 to 240 MHz) only. LINE 1 LINE 2 LINE 3 TUNER NET USB TUNER BAND Before tuning in to DAB stations, an initial scan must be performed. When you select the DAB for the first time, the initial scan is performed automatically. To listen to a DAB station, connect the antenna as described in “Connecting the DAB/FM antenna (RN803D)” (p.13). LINE 1 LINE 2 LINE 3 TUNER NET USB TUNER BAND TUNING BAND MEMORY TUNING BAND Preparing the DAB tuning MEMORY TUNING jj / ii PRESET ENTER 1 Press TUNER to select “TUNER” as the input source. 2 3 Press BAND to select the DAB band. Press TUNING jj / ii to select a DAB radio station. BASIC OPERATION DAB (Digital Audio Broadcasting) uses digital signals for clearer sound and more stable reception compared to analog signals. This unit can also receive DAB+ (an upgraded version of DAB) that allows for more stations using MPEG-4 audio codec (AAC+), which has a more efficient transmission method. PRESET DAB ENTER BBC Radio 4 A VOL. Note 1 Press TUNER to select “TUNER” as the input source. 2 Press BAND to select the DAB band. The initial scan starts. During the scan, the progress is displayed on the front display. When the scan is complete, the top of the list of the scanned stations appears on the front display. • “Off Air” appears when the selected DAB radio station is currently not available. • When the unit is receiving a secondary station, “2” appears next to “DAB”. Note English • If no DAB radio stations are found by an initial scan, “Not Found” appears on the front display, followed by “Off Air”. Press BAND twice to re-select the DAB band and scan again. • You can check reception strength of each DAB channel label (p. 31). • To perform an initial scan again after some DAB radio stations are stored, select “Initiate Scan” (p.46) in the “OPTION” menu. If you perform an initial scan again, the DAB radio stations currently registered to the preset numbers will be cleared. 29 En Listening to DAB radio (R-N803D) Using preset function ■ Recalling a preset station You can register up to 40 DAB radio stations as presets. Once you have registered stations, you can easily tune in to them by recalling the presets. 1 Press TUNER to select “TUNER” as the input source. 2 3 Press BAND to select the DAB band. Note You can register up to 40 favorite radio stations each for DAB and FM bands. TUNER NET Tune into a registered DAB radio station by selecting its preset number. Press PRESET j / i to select the desired DAB radio station. USB TUNER A BAND TUNING BAND MEMORY PRESET MEMORY ENTER HOME RETURN RETURN SETUP OPTION VOLUME OPTION ■ Registering a DAB radio station Select a DAB radio station and register it to a preset number. 2 Follow “Selecting a DAB radio station for reception” (p.29) to tune into the desired DAB radio station. Press MEMORY. Note • Preset numbers to which no stations are registered are skipped. • If this unit does not have any preset stations, “No Presets” is displayed. ■ Clearing preset DAB radio stations Clear DAB radio stations registered to the preset numbers. 1 Press TUNER to select “TUNER” as the input source. 2 3 4 Press BAND to select the DAB band. 5 Use the cursor keys (B / C) to select a preset DAB radio station to be cleared and press ENTER. If the preset DAB radio station is cleared “Cleared” appears and the next in-use preset number is displayed. 6 Repeat step 5 until all desired preset DAB radio stations are cleared. 7 To exit from the “OPTION” menu, press OPTION. By holding down MEMORY for more than 3 seconds, you can skip the following steps and automatically register the selected station to an empty preset number (i.e., the preset number following the last preset number used). 3 Press PRESET j / i to select the preset number to which the station will be registered. If you select a preset number to which no station is registered, “Empty” is displayed. If you select a preset number to which a station has already been registered, “Overwrite?” is displayed. MEMORY 02:Empty A VOL. “Empty” (not in use) or “Overwrite?” (in use) 4 Press MEMORY. When registration is complete, the display returns to the original state. Note To cancel registration, press RETURN or do not perform any operations for about 30 seconds. 30 En VOL. Note Cursor keys B / C ENTER 1 PRESET:01 PRESET j / i Press OPTION. Use the cursor keys (B / C) to select “Clear Preset” and press ENTER. Listening to DAB radio (R-N803D) Displaying the DAB information This unit can receive various types of DAB information when it is tuned in to a DAB radio station. Checking reception strength of each DAB channel label You can check reception strength of each DAB channel label (0 [none] to 100 [best]). TUNER PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET NET USB TUNER TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS PUSH - ENTER FLAT SPEAKERS A B RETURN CONNECT 1A L MEMORY R DISPLAY 1 2 TUNING BAND -30dB USB 5V YPAO MIC Select “TUNER” as the input source and tune into the desired DAB radio station. Press DISPLAY on the front panel. Each time you press the key, the displayed item changes. DAB Program Type Item name About 3 seconds later, the corresponding information appears. DAB Cursor keys B / C ENTER ENTER HOME RETURN SETUP OPTION VOLUME OPTION 1 Press TUNER to select “TUNER” as the input source. 2 3 4 Press BAND to select the DAB band. 5 Use the cursor keys (B / C) to select the desired DAB channel label. SPORT Press OPTION. Use the cursor keys (B / C) to select “Tune Aid” and press ENTER. TUNE AID 12B Level: 80 Information Item PRESET BASIC OPERATION PHONES BAND SELECT DAB channel label Information Service Label Station name DLS (Dynamic Label Segment) Information on the station Ensemble Label Ensemble name Program Type Station genre Date and Time Current date and time Audio Mode Audio mode (monaural/stereo) and bit rate CH Label/Freq Channel label and frequency Signal Quality Signal reception quality (0 [none] to 100 [best]) 6 Reception strength To exit from the “OPTION” menu, press OPTION. English Note Some information may not be available depending on the selected DAB radio station. 31 En Playing back music via Bluetooth You can play back music files stored on a Bluetooth device (such as mobile device) on the unit. Please also refer to the owner’s manual of your Bluetooth device. 3 On the Bluetooth device, select the unit (network name) from the available device list. After pairing has been completed and the unit is connected to the Bluetooth device, “Connected” appears on the front display, and Bluetooth indicator will be light up. BLUETOOTH This unit A VOL. Connected Bluetooth device (such as mobile device) Note Note • To use the Bluetooth function, set “Bluetooth” (p. 50) in the “Setup” menu to “On” (Default). • A Bluetooth device may not be detected by the unit or some feature may not be compatible, depending on the model. • You can transmit audio to Bluetooth speakers or headphones using “MusicCast CONTROLLER” (p. 20). The audio output can only be selected from “MusicCast CONTROLLER”. Connecting a Bluetooth device (pairing) • If the pass key is required, enter the number “0000”. • You can change the network name of this unit in “Network Name” (p.49) in the “Setup” menu. Playing back Bluetooth device contents Connect a paired Bluetooth device and start playback. Check the following beforehand: • Pairing has been completed. • Bluetooth function on the Bluetooth device is turned on. When connecting a Bluetooth device to the unit for the first time, the pairing operation is required to perform. Pairing is an operation that registers the Bluetooth devices with each other beforehand. Once pairing has been completed, subsequent reconnection will be easy even after the Bluetooth connection is disconnected. SPEAKERS A B PHONO SLEEP COAX 1 COAX 2 BLUETOOTH BLUETOOTH OPT 1 OPT 2 CD SPEAKERS A REPEAT B PHONO SHUFFLE SLEEP COAX 1 COAX 2 Playback keys BLUETOOTH BLUETOOTH OPT 1 1 2 OPT 2 CD Press BLUETOOTH to select “Bluetooth” as the input source. If another Bluetooth device is already connected, disconnect the Bluetooth connection before you perform a pairing operation. Turn on the Bluetooth function of the Bluetooth device. 32 En 1 Press BLUETOOTH to select “Bluetooth” as the input source. Note If the unit detects the Bluetooth device previously connected, the unit automatically connects to the Bluetooth device after Step 1. To establish another Bluetooth connection, first disconnect the current Bluetooth connection. Playing back music via Bluetooth 2 Operate the Bluetooth device to establish a Bluetooth connection. Select the unit’s model name from the Bluetooth device list on your device. When a connection is established, Bluetooth indicator on the front display will be light up. Note If you cannot connect the Bluetooth device, please perform pairing again. 3 Operate the Bluetooth device to play back music. Note You can use the playback keys on the remote control to control playback. Bluetooth • Bluetooth is a technology for wireless communication between devices within an area of about 10 meters (33 ft) employing the 2.4 GHz frequency band, a band which can be used without a license. Handling Bluetooth communications • The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of equipment. While Bluetooth compatible devices use a technology minimizing the influence of other components using the same radio band, such influence may reduce the speed or distance of communications and in some cases interrupt communications. • The speed of signal transfer and the distance at which communication is possible differs according to the distance between the communicating devices, the presence of obstacles, radio wave conditions and the type of equipment. • Yamaha does not guarantee all wireless connections between this unit and devices compatible with Bluetooth function. BASIC OPERATION Disconnecting a Bluetooth connection English Follow one of the procedures below to disconnect a Bluetooth connection. • Turn off the Bluetooth function on the Bluetooth device. • Hold down BLUETOOTH on the remote control for at least 3 seconds. • Select an input source other than “Bluetooth” on the unit. 33 En Playing back music stored on media servers (PCs/NAS) You can play back music files stored on your PC or DLNA-compatible NAS on the unit. 3 Click “Turn on media streaming”. 4 Select “Allowed” from the drop-down list next to the unit’s model name. NAS This unit PC Note • To use this function, the unit and your PC/NAS must be connected to the same router (p. 14). You can check whether the network parameters (such as the IP address) are properly assigned to the unit in “Information” (p.48) in the “Setup” menu. • To play back music files, the server software installed on the PC/NAS must support the music file formats that you want to play back. • The audio may be interrupted while using the wireless network connection. In this case, use the wired network connection. • You can connect up to 16 media servers to this unit. • For details on supported file formats, see “Supported file formats” (p.62). R-N803 Setting the media sharing of music files To play back music files in your computer with this unit, you need to make the media sharing setting between the unit and computer (Windows Media Player 12 or later). In here, setting with Windows Media Player in Windows 7 is taken as an example. ■ When using Windows Media Player 12 1 2 5 As with Step 4, select “Allowed” from the drop-down list next to devices (PCs or mobile devices) which you want to use as the media controllers. 6 Click “OK” to exit. Start Windows Media Player 12 on your PC. ■ When using a PC or a NAS with other DLNA server software installed Select “Stream”, then “Turn on media streaming...”. Refer to the instruction manual for the device or software and configure the media sharing settings. (Example of English version) The control panel window of your PC appears. 34 En Playing back music stored on media servers (PCs/NAS) Playback of PC music contents Use the following remote control keys to control playback. Follow the procedure below to operate the PC music contents and start playback. Keys Function Cursor keys Select a music file or folder. ENTER Starts playback if pressed while content is selected. Moves down one level if pressed while a folder is selected. RETURN Moves up one level. Note “_” (underscore) will be displayed for characters not supported by the unit. NET BAND USB NET TUNING MEMORY Playback keys Cursor keys B/C/D/E ENTER ENTER HOME Stops playback. s b/w f/a RETURN RETURN HOME SETUP Pauses/resumes playback. p/ e PRESET HOME Displays the root directory of the music server. NOW PLAYING Displays information about the song that’s playing. OPTION OPTION VOLUME NOW PLAYING MUTE REPEAT SHUFFLE Skips forward/backward. NOW PLAYING Note Playback keys Press NET repeatedly to select “Server” as the input source. SERVER 3 1 Use the cursor keys (B / C) to select a music server and press ENTER. Use the cursor keys to select an item and press ENTER. If a song is selected, playback starts and the playback information is displayed. SERVER You can configure the repeat/shuffle settings for the playback of PC music content. A NAS A 2 ■ Repeat/shuffle settings When the input source is “Server,” press REPEAT or SHUFFLE on the playback key repeatedly to select the playback method. Playback keys REPEAT A Song A Note • If playback of a music file selected from the unit is ongoing on your PC, the playback information is displayed. • You can register the current playback song as a preset (p. 41). • If you press the DISPLAY on the front panel repeatedly, you can switch the playback information on the front display (p. 22). SHUFFLE Setting Function Off Turns off the repeat function. One Plays back the current song repeatedly. All Plays back all songs in the current album (folder) repeatedly. Off Turns off the shuffle function. On Plays back songs in the current album (folder) in random order. English 1 You can also use a DLNA-compatible Digital Media Controller (DMC) to control playback. For details, see “DMC Control” (p.49). BASIC OPERATION TUNER 35 En Playing back music stored on media servers (PCs/NAS) ■ Automatic playback setting Use this setting to choose whether to automatically play back music from your PC or from the NAS when turning on the unit or when selecting “Server” as the input source. 1 When the input source is “Server”, press OPTION. 2 Use the cursor keys (B / C) to select “Auto Playback” and press ENTER. 3 Use the cursor keys (D / E) to select “On” (enable) or “Off” (disable). 4 To exit from the menu, press OPTION. 36 En Listening to Internet radio Listening to Internet radio Note • To use this function, the unit must be connected to the Internet (p. 14). You can check whether the network parameters (such as the IP address) are properly assigned to the unit in “Information” (p.48) in the “Setup” menu. • You may not be able to receive some Internet radio stations. • This unit uses the airable.Radio service. airable is a service of Tune In GmbH. • This service may be discontinued without notice. TUNER NET BAND Use the cursor keys to select an item and press ENTER. If an Internet radio station is selected, playback starts and the playback information is displayed. NET RADIO A JazzST Use the following remote control keys to control playback. Keys Function Cursor keys Select the Internet radio station or category such as the genre. ENTER Starts playback if pressed while an Internet radio station is selected. Moves down one level if pressed while a category is selected. RETURN Moves up one level. NET TUNING MEMORY Cursor keys B/C/D/E ENTER USB 2 PRESET ENTER HOME RETURN SETUP OPTION RETURN HOME VOLUME NOW PLAYING Playback keys Stops playback. HOME Displays the top categories if pressed during playback. NOW PLAYING Displays the playback information for the Internet radio station. MUTE NOW PLAYING REPEAT s SHUFFLE BASIC OPERATION You can listen to Internet radio stations from all over the world. Playback keys Note Press NET repeatedly to select “Net Radio” as the input source. The station list appears on the front display. NET RADIO • You can register the current playback station as a preset (p. 41). • If you press the DISPLAY on the front panel repeatedly, you can switch the playback information on the front display (p. 22). • Some information may not be available depending on the station. A Radios English 1 37 En Playing back iPhone/iTunes music via a network (AirPlay) The AirPlay function allows you to play back iPhone/ iTunes music on the unit via network. PC 3 Select a song and start playback. The unit automatically selects “AirPlay” as the input source and starts playback. The playback information is displayed on the front display. iTunes Note Starts playback on iTunes or iPhone Router This unit iPhone Playback starts • If you press the DISPLAY on the front panel repeatedly, you can switch the playback information on the front display (p. 22). • You can turn on the unit automatically when starting playback on iTunes or iPhone by setting “Standby (Network Standby)” (p.49) in the “Setup” menu to “On”. • You can edit the network name (the unit’s name on the network) displayed on iPhone/iTunes in “Network Name” (p.49) in the “Setup” menu. • You can adjust the unit’s volume from the iPhone/iTunes during playback. Note To use this function, the unit and your PC or iPhone must be connected to the same router (p. 14). AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac with OS X Mountain Lion or later, and Mac and PC with iTunes 10.2.2 or later. (as of June 2017) Playback of iPhone/iTunes music contents CAUTION Adjusting the volume on iTunes or iPhone may make the volume unexpectedly loud, which could result in damage to your hearing or to the device. If the playback volume is too loud, stop playback immediately on iTunes or iPhone. We recommend using “Volume interlock” (p. 46) in the “Option” menu to limit the changes in volume from iTunes or iPhone. Use the following remote control keys to control playback. Keys p/ e Follow the procedure below to play back iPhone/iTunes music contents on the unit. 1 Turn on the unit, and start iTunes on the PC or display the playback screen on the iPhone. If the iPhone/iTunes recognizes the unit, the AirPlay icon appears. iOS10 (example) iTunes (example) Note If the icon does not appear, check whether the unit and PC/iPhone are connected to the router properly. 2 On the iPhone/iTunes, click (tap) the AirPlay icon and select the unit (network name of the unit) as the audio output device. 38 En Functions s Playback keys b/w f/a Pauses/resumes playback. Stops playback. Skips forward/backward. REPEAT Changes the Repeat settings. SHUFFLE Changes the Shuffle settings. Playing back music stored on a USB storage device Playing back music stored on a USB storage device You can play back music files stored on a USB storage device on the unit. Refer to the instruction manuals for the USB storage device for more information. Note • Do not connect devices other than USB mass storage class devices (such as USB chargers or USB hubs), PCs, card readers, an external HDD, etc. • Some features may not be compatible, depending on the model or manufacturer of the USB storage device. • For details on supported USB storage devices and file formats, see “Supported devices and file formats” (p.62). Connecting a USB storage device Playback of USB storage device contents 1 Follow the procedure below to operate the USB storage device contents and start playback. Connect the USB storage device to the USB jack. Note This unit (front) INPUT SPEAKERS A B USB 5V “_” (underscore) will be displayed for characters not supported by the unit. 1A YPAO MIC LINE 1 LINE 2 LINE 3 TUNER NET USB BASIC OPERATION PHONES BASS USB BAND TUNING MEMORY Cursor keys B/C/D/E ENTER USB storage device PRESET ENTER HOME RETURN SETUP OPTION RETURN HOME Connected OPTION VOLUME A VOL. NOW PLAYING MUTE REPEAT SHUFFLE NOW PLAYING Note • If the USB storage device contains many files, it may take time to load the them. In this case, “Loading...” appears in the front display. • Disconnect the USB storage device from the USB jack when it is not in use. • Stop playback of the USB storage device before disconnect it from the USB jack. • You cannot connect the PC to the USB jack of the unit. • This unit cannot charge USB storage devices while it is in standby mode. Playback keys 1 Press USB to select “USB” as the input source. USB A VOL. Blues 2 Use the cursor keys to select an item and press ENTER. If a song is selected, playback starts and the playback information is displayed. USB Track #3 English USB A VOL. Note • You can register the current playback song as a preset (p. 41). • If you press the DISPLAY on the front panel repeatedly, you can switch the playback information on the front display (p. 22). 39 En Playing back music stored on a USB storage device Use the following remote control keys to control playback. Keys Function Cursor keys Select a music file or folder. ENTER Starts playback if pressed while a music file is selected. Moves down one level if pressed while a folder is selected. RETURN Moves up one level. p/ e Playback keys s b/w f/a Pauses/resumes playback. Skips forward/backward. Displays the root directory of the USB device. NOW PLAYING Displays information about the song that’s playing. ■ Repeat/shuffle settings You can configure the repeat/shuffle settings for playback of USB storage device contents. If the input source is “USB,” press REPEAT or SHUFFLE on the playback keys repeatedly to select the playback method. Playback keys REPEAT SHUFFLE 40 En Setting Use this setting to choose whether to automatically play back music from your USB storage device when turning on the unit or when selecting “USB” as the input source. 1 When the input source is “USB”, press OPTION. 2 Use the cursor keys (B / C) to select “Auto Playback” and press ENTER. 3 Use the cursor keys (D / E) to select “On” (enable) or “Off” (disable). 4 To exit from the menu, press OPTION. Stops playback. HOME 1 ■ Automatic playback setting Function Off Turns off the repeat function. One Plays back the current song repeatedly. All Plays back all songs in the current album (folder) repeatedly. Off Turns off the shuffle function. On Plays back songs in the current album (folder) in random order. Registering the current playback song/station (Preset function) Registering the current playback song/station (Preset function) When you select network sources and USB as the input source, you can register the current playback song or streaming station as a preset up to 40. You can then easily recall any preset song/station by selecting its preset number. The following input sources can be set as presets. Server, Net Radio, USB and streaming services. Note • You can also register songs and stations as presets using “MusicCast CONTROLLER” (p.20). • When you register music files stored on a USB storage device or a PC/NAS, this unit memorizes the relative position of the music files in the folder. If you have added or deleted any music files to or from the folder, this unit may not recall the music file correctly. In such cases, register the items again. LINE 2 LINE 3 TUNER NET USB TUNING MEMORY PRESET MEMORY ENTER Press NET or USB to select the desired input source. 2 Press PRESET j / i to select a preset number. 3 Press ENTER to recall preset. Note • It may take a while to recall a preset song or a preset station. • To cancel recalling, press RETURN. • You can also recall preset songs or preset stations using “MusicCast CONTROLLER” (p.20). Clearing a preset USB BAND 1 PRESET j / i 1 Press NET or USB to select the desired input source. 2 Press PRESET j / i to select a preset number to be cleared. 3 Press CLEAR on the front panel to clear the preset. If the preset content is cleared, “Empty” appears. BASIC OPERATION NET LINE 1 Recalling a preset ENTER Registering to a preset 1 Playback a song or streaming station you want to register. 2 Press MEMORY. Note 3 PRESET j / i to select the preset number to which the song/station will be registered. If you select a preset number to which no station is registered, the message “Empty” is displayed. 4 Press MEMORY. When registration is complete, the display returns to the original state. English By holding down MEMORY for more than 3 seconds, you can skip the following steps and automatically register the selected song/station to an empty preset number (i.e., the preset number following the last preset number used). Note To cancel registration, press RETURN. 41 En ADVANCED OPERATION Optimizing the speaker settings automatically (YPAO) The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections, measures the distances from them to your listening position, and then automatically optimizes the speaker settings, such as volume balance and acoustic parameters, to suit your room. 1 Press A (power) on the front panel to turn on this unit. 2 Turn on the subwoofer and set the volume to half. If the crossover frequency is adjustable, set it to maximum. Note • The YPAO function of this unit adopts the YPAO-R.S.C. (Reflected Sound Control) technology that enables to create natural sound fields like a room specifically designed for acoustic perfection. • Note the following regarding YPAO measurement. – Test tones are output at high volume and may surprise or frighten small children. – Test tone volume cannot be adjusted. – Keep the room as quiet as possible. – Stay in a corner of the room behind the listening position so that you do not become an obstacle between speakers and the YPAO microphone. – Do not connect headphones. VOLUME SW MIN 3 SPEAKERS SPEAKERS A/B A B PHONO CROSSOVER/ HIGH CUT SLEEP MAX MIN MAX Configure the following settings. • Press SPEAKERS A/B on the front panel or remote control to select the speakers to be used. • Set the BASS control and TREBLE control on the front panel to 0 (center position). • Set the BALANCE control on the front panel to the center position. • Set the LOUDNESS control on the front panel to FLAT (center position). • If Pure Direct is turned on, press PURE DIRECT on the front panel to turn it off. • COAX 1 COAX 2 BLUETOOTH SPEAKERS A/B OPT 1 OPT 2 CD LINE 1 LINE 2 LINE 3 TUNER NET USB BAND TUNING MEMORY BASS PRESET TREBLE BALANCE LOUDNESS Note Cursor keys B/C/D/E ENTER ENTER HOME RETURN RETURN SETUP OPTION VOLUME NOW PLAYING 42 En PURE DIRECT MUTE • The speaker settings are individually saved depending on the speaker system (A, B, A+B). • When using YPAO, select the speaker system (A+B) only for the bi-wire connection. If you select the speaker system (A+B) when connecting other speakers to the SPEAKERS A/B terminals, the measurement will not be performed properly. Optimizing the speaker settings automatically (YPAO) 4 Place the YPAO microphone at your listening position and connect it to the YPAO MIC jack on the front panel. 6 Note To check the measurement result, press the cursor key (E). If “No Warning” appears on the front display, the measurement is properly completed. YPAO( A Place the YPAO microphone at your listening position (same height as your ears). We recommend the use of a tripod as a microphone stand. You can use the tripod screws to stabilize the microphone. No Warning Note If any warning message (such as W-1) appears on the front display, see “Warning messages” (p. 45). YPAO MIC 7 8 YPAO microphone at listening position [ENTER]:Save YPAO( A [ENTER]:Cancel The following message appears on the front display. [ENTER]:Start Note To cancel the operation, disconnect the YPAO microphone before starting the measurement. 5 To start the measurement, press ENTER. The measurement will start in 10 seconds. It takes about 1 minute to perform the measurement. To save the measurement results, use the cursor keys (B / C) to select “Save” and press ENTER. To finish the measurement without saving the result, use the cursor keys (B / C) to select “Cancel” and press ENTER. YPAO( A Ear height YPAO Press the cursor key (D) or RETURN. Note You can change the YPAO settings (YPAO On/Off and YPAO Volume) in the “Setup” menu (p. 50). 9 Disconnect the YPAO microphone from this unit. ADVANCED OPERATION YPAO MIC jack YPAO( A Disconnect MIC Notice Note To cancel the measurement, press RETURN and then follow the procedure in “Error messages” (p. 44). The YPAO microphone is sensitive to heat, so should not be placed anywhere where it could be exposed to direct sunlight or high temperatures (such as on top of AV equipment). “Result Info.” appears on the front display when the measurement finishes. YPAO( A English Result Info. Note If “Error Info” appears, press the cursor key (E) to check the error message (p. 44). 43 En Optimizing the speaker settings automatically (YPAO) Error messages If any error message is displayed during the measurement, resolve the problem and perform YPAO again. YPAO E-1 Noisy Error message Cause Remedy The noise is too loud. Keep the room quiet and start the measurement again. E-2 No Signal The YPAO microphone cannot detect test tones. Connect the YPAO microphone to the YPAO MIC jack firmly and start the measurement again. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. E-3 No MIC The YPAO microphone has been removed. Connect the YPAO microphone to the YPAO MIC jack firmly and start the measurement again. E-4 User Cancel The measurement has been canceled. Start the measurement again as necessary. E-5 PHONES The headphones are connected to the PHONES jack of this unit. Disconnect the headphones and start the measurement again. E-10 Internal Error An internal error has occurred. Exit YPAO and then turn off and on this unit. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. E-20 No SPEAKERS Speakers are not detected. Press SPEAKERS A/B to select the speakers to be used and start the measurement again. If this error occurs even when the speakers are properly selected, turn off this unit and check the speaker connections. E-21 Control Knob The BASS/TREBLE/BALANCE/LOUDNESS control positions are improper. Set all the controls to the center position and start the measurement again. E-22 Pure Direct Pure Direct is turned on. Press PURE DIRECT on the front panel to turn off Pure Direct and start the measurement again. E-1 Noisy Note After checking the error message, press the cursor key (D) to return to the previous state and follow the procedure below, – To start the measurement again: Use the cursor keys (B / C) to select “Retry” and press ENTER. Proceed to Step 5 in page 43. – To exit YPAO: Use the cursor keys (B / C) to select “Exit” and press ENTER. 44 En Optimizing the speaker settings automatically (YPAO) Warning messages If a warning message is displayed after the measurement, you can still save the measurement results. However, we recommend you perform YPAO again in order to use this unit with the optimal speaker settings. YPAO W-1 Out of Phase Warning message Cause Remedy W-1 Out of Phase A speaker cable may be connected with the reverse polarity (+/-). check the cable connections (+/–) of the speakers. If the speaker is connected incorrectly, turn off this unit and then reconnect the speaker cable. Depending on the type of speakers or room environment, this message may appear even if the speakers are connected correctly. In this case, you can ignore the message. W-2 Over Distance A speaker is placed more than 24 m (80 ft) from the listening position Move the speaker within 24m (80 ft) of the listening position. There are significant volume differences between the speakers. Check the usage environment and cable connections (+/–) of each speaker, and the volume of the subwoofer. We recommend using the same speakers or speakers with specifications that are as similar as possible. W-3 Level Error Note English ADVANCED OPERATION • If more than one warning is detected, use the cursor keys (B / C) to check another warning message. • To return to the previous state after checking the warning message, press the cursor key (D)). 45 En Configuring playback settings for different playback sources (Option menu) You can configure separate playback settings for different playback sources. This menu allows you to easily configure settings during playback. MEMORY Item PRESET Auto Playback Cursor keys B/C/D/E ENTER ENTER HOME RETURN SETUP OPTION 1 MUTE This setting is applied separately to each input source. Setting range -10.0 dB to 0.0 dB to +10.0 dB (0.5 dB increments) A Volume Trim VOL. Default 0.0 dB Use the cursor keys to select an item and press ENTER. ■ Signal Info. Note Displays information about audio signal. To return to the previous state during menu operations, press RETURN. 3 4 Selects whether to automatically play back music from your PC/NAS or USB storage device when the unit is turned 36, 40 on or when the corresponding input source is selected. Note Press OPTION. OPTION 2 46 Corrects volume differences between input sources. If you are bothered by volume differences when switching between input sources, use this function to correct it. OPTION VOLUME Page ■ Volume Trim RETURN NOW PLAYING Function Vol.Interlock Enables/Disables volume controls from (Volume interlock) iPhone/iTunes via AirPlay. Choices Use the cursor keys (D / E) to select a setting. FORMAT Audio format of the input signal To exit from the menu, press OPTION. SAMPLING The number of samples per second of the input digital signal Option menu items Note To switch the information on the front display, press the cursor keys (B / C) repeatedly. Note Available items vary depending on the selected input source. Item Function Page ■ Vol.Interlock (Volume interlock) Enables/disables volume controls from iPhone/iTunes via AirPlay. Volume Trim Corrects volume differences between input sources. 46 Signal Info. Displays information about the audio signal. 46 Off Disables volume controls from iPhone/iTunes. Auto Preset Automatically registers FM radio stations with strong signals as presets. 25 Ltd (Default) Clear Preset Clears radio stations registered to preset numbers. Enables volume controls from iPhone/iTunes within the limited range (-80.0 dB to -20.0 dB and mute). 27 Full Enables volume controls from iPhone/iTunes in the full range (-80.0 dB to +16.5 dB and mute). Initiate Scan (R-N803D only) Performs an initial scan for DAB radio reception. 29 Tune Aid (R-N803D only) Checks reception strength of each DAB channel label. 31 46 En Settings Configuring various functions (Setup menu) Configuring various functions (Setup menu) You can configure the unit’s various functions. MEMORY Cursor keys B/C/D/E ENTER PRESET ENTER HOME RETURN RETURN SETUP SETUP OPTION VOLUME NOW PLAYING 1 MUTE Press SETUP. SETUP Network 2 Use the cursor keys (B / C) to select a menu item and press ENTER. SETUP Volume VOLUME 3 ADVANCED OPERATION Max Volume Use the cursor keys (D / E) to select a setting and press ENTER. MAX VOL +16.5dB Note To return to the previous state during menu operations, press RETURN. To exit from the menu, press SETUP. English 4 47 En Configuring various functions (Setup menu) Setup menu items Menu item Function Page Connection Selects the network connection method. 48 Information Displays the network information on the unit. 48 IP Address Configures the network parameters (such as IP address). 49 DMC Control Selects whether to allow a DLNA-compatible Digital Media Controller (DMC) to control playback. 49 Standby (Network Standby) Selects whether to enable/disable the function that turns on the unit from other network devices. 49 Network Name Edits the network name (the unit’s name on the network) displayed on other network devices. 49 Network Update (Network Update) Updates the firmware via the network. 50 On/Off Enables/disables the Bluetooth functions. 50 Bluetooth Standby (Bluetooth Standby) Selects whether to enable/disable the function that turns on the unit from Bluetooth devices (Bluetooth standby). 50 YPAO (Speaker A, Speaker B, Speaker A+B) YPAO On/Off Enables/disables the reflection of the YPAO measurement. 50 VOL (YPAO Volume) Enables/disables the YPAO volume function. 50 Max Volume Sets the maximum volume to prevent excessive loudness. 50 Initial Volume Sets the initial volume for when this receiver is turned on. 50 AutoPowerStdby (Auto Power Standby) Sets the amount of time for the auto standby function. 51 ECO Mode Enables/disables the eco mode (power saving mode). 51 Volume Network Configures the network settings. ■ Connection Selects the network connection method. ■ Information Displays the network information on the unit. NEW FW Available Appears if an update for this unit’s firmware is available (p. 54). STATUS The connection status of the network. Wired Select this option when you want to connect the unit to a network with a commerciallyavailable network cable (p. 14). MC NET Wireless Select this option when you want to connect the unit to a network via the wireless router or access point (p. 16). Status of the MusicCast Network. If “Ready” appears, you can use the MusicCast CONTROLLER app. MAC WirelessDirect Select this option when you want to connect a mobile device to the unit directly. For details on settings, see “Connecting a mobile device to the unit directly (Wireless Direct)” (p. 19). Displays MAC address of the unit. MAC address will vary depending on the connection method (wired LAN connection or wireless LAN / Wireless Direct connection). SSID (When using wireless LAN connection or Wireless Direct) The SSID of this unit on the wireless network. IP IP address SUBNET Subnet mask GATEWAY The IP address of the default gateway DNS P The IP address of the primary DNS server DNS S The IP address of the secondary DNS server Note When this unit is in the MusicCast extended mode, “Extend” is displayed. For details on the extended mode, refer to “MusicCast Setup Guide” on the Yamaha website. 48 En Configuring various functions (Setup menu) ■ IP Address Configures the network parameters (such as IP address). DHCP Select whether to use a DHCP server. Off Does not use a DHCP server. Configure the network parameters manually. For details, see “Manual network settings”. On (Default) Uses a DHCP server to automatically obtain the unit’s network parameters (such as IP address). ■ Standby (Network Standby) Selects whether the unit can be turned on from other network devices (network standby). Off Disables the network standby function. On Enables the network standby function. (The unit consumes more power than when “Off” is selected.) Auto (Default) Enables the network standby function. The unit is set to the power saving mode when the unit is disconnected from the network. Manual network settings Set “DHCP” to “Off”. Use the cursor keys (B / C) to select a parameter type. IP Specifies an IP address. SUBNET Specifies a subnet mask. GATEWAY Specifies the IP address of the default gateway. DNS P Specifies the IP address of the primary DNS server. DNS S Specifies the IP address of the secondary DNS server. 3 With an advanced energy saving design, this product achieves a low power consumption of not more than two watts when in Network Standby mode. ■ Network Name Edits the network name (the unit’s name on the network) displayed on other network devices. 1 Use the cursor keys (D / E) to select the edit position. IP Address1•••192 NETWORK Network Name 2 (Example: IP address setting) Use the Cursor keys (B / C) to change a value. 5 To exit from the menu, press SETUP. R-N803 XXXXXX 3 ■ DMC Control Does not allow DMCs to control playback. Enable (Default) Allows DMCs to control playback. Note Use the cursor keys (D / E) to move the edit position and the cursor keys (B / C) to select a character. NET NAME Selects whether to allow DLNA-compatible Digital Media Controller (DMC) to control playback. Disable Press ENTER twice to enter the name edit display. NET NAME Use the cursor keys (D / E) to switch between segments (Address1, Address2...) of the address. 4 Select “Network Name” and press ENTER. ADVANCED OPERATION 1 2 R-N803 XXXXXX You can insert / delete a character, by pressing PRESET i (insert) or PRESET j (delete). 4 5 To confirm the new name, press ENTER. To exit from the menu, press SETUP. English A Digital Media Controller (DMC) is a device that can control other network devices through the network. When this function is enabled, you can control playback of the unit from DMCs (such as Windows Media Player 12) on the same network. 49 En Configuring various functions (Setup menu) ■ Update (Network Update) Updates the firmware via the network. Perform Update Starts the process to update the unit’s firmware. For details, see “Updating the unit’s firmware via the network” (p. 54). Version Displays the version of the firmware installed on the unit. ID Displays the system ID number. YPAO Configures the setting related to YPAO. The following settings are available for each speaker system (Speaker A, Speaker B, Speaker A+B). Note The corresponding speaker system and following settings will be selectable after the YPAO measurement result is saved. ■ YPAO On/Off Bluetooth Enables/disables the reflection of the YPAO measurement. Configures the Bluetooth settings. Off Disables the reflection of the YPAO measurement. ■ On/Off On (Default) Enables the reflection of the YPAO measurement. Enables/disables the Bluetooth function (p. 32). Off Disables the Bluetooth function. On (Default) Enables the Bluetooth function. Immediately after selecting the “On”, output of the network source is paused. ■ Standby (Bluetooth Standby) Selects whether to enable/disable the function that turns on the unit from Bluetooth devices (Bluetooth standby). If this function is set to “On”, the unit automatically turns on when a connect operation (p. 32) is performed on the Bluetooth device. Off Disables the Bluetooth standby function. On (Default) Enables the Bluetooth standby function. (The unit consumes more power than when “Off” is selected.) Note This setting is not available when “Standby (Network Standby)” (p. 49) is set to “Off”. ■ VOL (YPAO Volume) Enables/disables the YPAO volume function. When the YPAO Volume function is enabled, the high- and lowfrequency levels are automatically adjusted according to the volume so that you can enjoy natural sounds even at low volume. Off Disables the YPAO Volume function. On (Default) Enables the YPAO Volume function. Note • The YPAO Volume function is disabled when “YPAO On/Off” is set to “Off”. • When the YPAO volume function is enabled, the YPAO VOL. indicator on the front display lights up. • The LOUDNESS control (p. 24) does not function when the YPAO Volume function is enabled. Volume Configures the volume-related settings. ■ Max Volume Sets the maximum volume to prevent excessive loudness. Setting range -30 dB to +15.0 dB / +16.5 dB (5 dB step) Default +16.5 dB ■ Initial Volume Sets the initial volume when the receiver is turned on. Setting range Off, Mute, -80.0 dB to +16.5 dB (0.5 dB Step) Default Off 50 En Configuring various functions (Setup menu) AutoPowerStdby (Auto Power Standby) Enables/disables the auto-standby function. If you do not operate the unit for the specified time, the unit will automatically go into standby mode. Off Does not set the unit to standby mode automatically. On Sets the unit to standby mode automatically. While NET, BLUETOOTH or USB is selected as the input source, the unit will switch to standby mode if the selected source is not played back for 20 minutes. For all input sources, the unit will switch to standby mode if it is not operated for 8 hours. Default U.K. and Europe models: On Other models: Off Note Just before the unit enters standby mode, “AutoPowerStdby” appears and then countdown starts in the front display. ECO Mode Off (Default) Disables the eco mode. On Enables the eco mode. ADVANCED OPERATION Enables/disables the eco (power saving) mode. When the eco mode is enabled, you can reduce the unit’s power consumption. The new setting will take effect after the unit is restarted. Be sure to press ENTER to restart the unit after selecting a setting. Note English When “ECO Mode” is set to “On”, the front display may become dark. 51 En Configuring the system settings (ADVANCED SETUP menu) Configure the system settings of the unit using the front panel controls. RETURN A (power) VERSION••xx.xx PURE DIRECT DIMMER DISPLAY MODE MEMORY CLEAR BAND PRESET TUNING VOLUME INPUT BASS BALANCE TREBLE LOUDNESS SELECT PUSH - ENTER FLAT PHONES SPEAKERS A B Checking the firmware version (VERSION) Check the version of firmware currently installed on the unit. -30dB USB RETURN 5V CONNECT 1A YPAO MIC L R Note DISPLAY 1 2 3 4 5 SELECT/ENTER • You can also check the firmware version in “Update (Network Update)” (p. 50) in the “Setup” menu. • It may take a while until the firmware version is displayed. Press A (power) to turn off the unit. While holding down RETURN, press A (power). Rotate SELECT/ENTER to select an item. Press SELECT/ENTER to select a setting. Press A (power) to set the unit to turn off and turn it on again. The new settings take effect. Function SP IMP.••8¬MIN Change the unit’s speaker impedance settings depending on the impedance of the speakers connected. ADVANCED SETUP menu items Item Changing the speaker impedance setting (SP IMP.) Page Settings VERSION Checks the version of firmware currently installed on the unit. 52 4  MIN Select this option when you connect speakers with an impedance of 4 ohms to less than 8 ohms to the unit. SP IMP. Changes the speaker impedance setting. 52 8  MIN (Default) Select this option when you connect speakers with an impedance of 8 ohms or more to the unit. REMOTE ID Selects the unit’s remote control ID. 52 TU (Asia and General models only) Sets tuner frequency step. 53 INIT Restores the default settings. 53 UPDATE Updates the firmware. 53 Selecting the remote control ID (REMOTE ID) REMOTE ID••ID1 Change the unit’s remote control ID so that it matches the remote control’s ID. Select “ID1” normally. Select “AUTO” only when you use the remote control supplied with some Yamaha player. Settings ID1 (Default), AUTO 52 En Configuring the system settings (ADVANCED SETUP menu) Setting tuner frequency step (TU) Updating the firmware (UPDATE) UPDATE•NETWORK TU••••FM50/AM9 Settings FM100/AM10, FM50/AM9 (Default) New firmware that provides additional features or product improvements will be released as needed. If the unit is connected to the Internet, you can download the firmware via the network. For details, refer to the information supplied with updates. Restoring the default settings (INIT) ■ Firmware update procedure (Asia and General models only) Selects the step size for locating tuner frequencies. INIT••••CANCEL Restores the default settings for the unit. Choices Do not perform this procedure unless firmware update is necessary. Also, make sure you read the information supplied with updates before updating the firmware. 1 Press SELECT/ENTER repeatedly to select “USB” or “NETWORK” and press DISPLAY to start firmware update. Choices NETWORK Initialize all of the network, Bluetooth and USB settings. When performing the initialization, the preset (p. 41) registered by NET/USB input will be cleared. CANCEL Does not perform an initialization. USB Update the firmware using a USB memory device. NETWORK Update the firmware via the network. Note If the unit detects newer firmware over the network, “NEW FW Available” appears as the “Information” menu item in “Network”. In this case, you can also update the unit’s firmware by following the procedure in “Updating the unit’s firmware via the network” (p. 54). ADVANCED OPERATION Restores the default settings for the unit. English ALL 53 En Updating the unit’s firmware via the network New firmware that provides additional features or product improvements will be released as needed. If the unit is connected to the Internet, you can download the firmware via the network and update it. Notice • Do not operate the unit or disconnect the power cable or network cable during firmware update. Firmware update takes about 5 minutes or more (depending on your Internet connection speed). • If the unit is connected to the wireless network via a wireless network adapter, network update may not be possible depending on the condition of the wireless connection. In this case, update the firmware using the USB memory device (p. 53). ■ Notification of new firmware update Note You can also update the firmware using the USB memory device from the “ADVANCED SETUP” menu (p. 53). MEMORY Cursor keys B/C ENTER NEW FW PRESET Update [ENTER] ENTER HOME RETURN SETUP OPTION RETURN SETUP VOLUME NOW PLAYING MUTE 1 2 Press SETUP. 3 Use the cursor keys (B / C) to select “Information” and press ENTER. If new firmware is available, “NEW FW Available” appears on the front display. Use the cursor keys (B / C) to select “Network” and press ENTER. NEW FW Available 4 5 Press RETURN to return the previous state. Use the cursor keys (B / C) to select “Update” and press ENTER. UPDATE Perform Update 6 To start the firmware update, press ENTER. The unit to restart and the firmware update starts. Note To cancel the operation without updating the firmware, press SETUP. 7 If “UPDATE SUCCESS” appears on the front display, press A (power) on the front panel. The firmware update is complete. 54 En When new firmware is available on the network, “NEW FW” will be displayed on the front display for a short period of time when the unit is turned on. To update the firmware, press ENTER (as described in Step 6) while the notification is displayed. If “UPDATE SUCCESS” appears on the front display, press A (power) on the front panel to turn off the unit. ADDITIONAL INFORMATION Troubleshooting Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, set this unit to standby mode, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. ■ General See page Possible cause Remedy The protection circuitry has been activated three times consecutively. If the unit is in this condition, the power indicator on the front panel blinks when you try to turn on the power. As a safety precaution, capability to turn on the power is disabled. Contact your nearest Yamaha dealer or service center to request repair. The power cord is not connected or the plug is not completely inserted. Connect the power cord firmly. The protection circuitry has been activated because of a short circuit, etc. Check that the speaker wires are not touching each other and then turn the power of this unit back on. 11 The internal microcomputer has frozen, due to an external electric shock (such as lightning or excessive static electricity) or to a drop in the power supply voltage. Press A (power) on the front panel to turn off the unit and turn it on again after at least 15 seconds elapse. (If the problem persists, disconnect the power cable from the AC wall outlet and plug it again.) — The power does not turn off. The internal microcomputer has frozen, due to an external electric shock (such as lightning or excessive static electricity) or to a drop in the power supply voltage. Press A (power) on the front panel to turn off the unit and turn it on again after at least 15 seconds elapse. (If the problem persists, disconnect the power cable from the AC wall outlet and plug it again.) — No sound. Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables may be defective. 10 No appropriate input source has been selected. Select an appropriate input source with the INPUT selector on the front panel (or one of the input selection key on the remote control). 22 The SPEAKERS A/B switches are not set properly. Turn on the corresponding SPEAKERS A or SPEAKERS B. 22 Speaker connections are not secure. Secure the connections. 10 Output has been muted. Turn off the mute. 8 Headphones are connected to the PHONES jack. Disconnect the headphones. The Max volume or Initial volume setting is set too low. Check the settings for “Max Volume” and “Initial Volume” in the “Setup” menu. The component corresponding to the selected input source is turned off or is not playing. Turn the component on and make sure it is playing. The audio output of a device connected to a digital audio input (COAXIAL/ OPTICAL jacks) is set to other than PCM. Set the audio output of the connected device to PCM. — — 5 ADDITIONAL INFORMATION The power does not turn on. 50 — — 55 En English Problem Troubleshooting Problem Possible cause Remedy See page Set the speaker impedance to match your speakers. 52 Check that the speaker wires are not touching each other and then turn the power of this unit back on. 11 This unit has become too hot. Make sure the openings on the top panel are not blocked. — The auto power standby function has turned this unit off. Change the auto power standby (“AutoPowerStdby” in the “Setup” menu) to turn off. 51 Incorrect cable connections. Connect the cables properly. If the problem persists, the cables may be defective. 10 Incorrect setting for the speaker balance. Set the BALANCE control to the appropriate position. 23 There is a lack of bass and no ambience. The + and – wires are connected in reverse at the amplifier or the speakers. Connect the speaker wires to the correct + and – phase. 11 A “humming” sound can be heard. Incorrect cable connections. Connect the audio plugs firmly. If the problem persists, the cables may be defective. 10 No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit. 10 The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The turntable should be connected to this unit through the MC head amplifier. The sound is degraded when listening with the headphones connected to the CD player or the tape deck connected to this unit. The power of this unit is turned off, or this unit is set to standby mode. Turn on the power of this unit. The sound level is low. The loudness control function is operating. The sound suddenly goes off. Only the speaker on one side can be heard. The protection circuitry has been activated because of a short circuit, etc. — — Turn down the volume, set the LOUDNESS control to the FLAT position, and then adjust the volume again. 24 ■ Remote control Problem The remote control does not work nor function properly. 56 En Remedy See page The remote control will function within a maximum range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel. 9 Possible cause Wrong distance or angle. Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. Reposition this unit. The batteries are weak. Replace all batteries. — 9 Troubleshooting ■ FM reception Problem The FM radio reception strength is poor, and noise can be heard. The radio station cannot be automatically selected. Possible cause Remedy See page The unit is receiving radio interference, such as multipath reflections. Change the antenna height, direction, or place of installation. ― The unit is receiving in a region located far away from the radio station. Press MODE on the front panel to select “MONO” (monaural mode). 25 Use a commercially-available outdoor antenna. ― Use a commercially-available outdoor antenna. ― The FM radio signal is weak. Select the station manually. 25 ■ AM reception (R-N803) Problem Possible cause Remedy See page The AM radio reception strength is poor, and noise can be heard. The unit is picking up noise from sources such as a fluorescent light or a motor. In some environments, it may be difficult to completely eliminate noise. However, using a commercially-available outdoor antenna may help to reduce noise. ― The AM radio signal is weak. Change the direction of the AM antenna. 13 Select the station manually. 25 Use a commercially-available outdoor antenna. Connect the supplied AM antenna to the ANTENNA(AM) jack. ― Auto presets can be used with FM radio stations only. AM radio stations must be manually registered. 26 ■ DAB reception (R-N803D) Possible cause Cannot tune into any DAB stations. The initial scan has not been performed. Perform the initial scan. 29 The DAB radio signal is weak. Change the antenna height, direction, or place of installation. 13 There is no DAB coverage in your area. Check with your dealer or WorldDMB Online at “http://www.worlddab.org” for a listing of the DAB coverage in your area. ― The DAB radio signal is weak. Change the antenna height, direction, or place of installation. 13 There is no DAB coverage in your area. Check with your dealer or WorldDMB Online at “http://www.worlddab.org” for a listing of the DAB coverage in your area. ― The initial scan is not successful (“NotFound” appears on the front display). Remedy See page Problem 57 En ADDITIONAL INFORMATION The stations may have been registered automatically (Auto Preset). English AM radio stations cannot be registered (preset). Troubleshooting Problem Possible cause The DAB radio reception strength is poor, and noise (such as hiss, crackle and jitter) can be heard. The DAB radio signal is weak. The DAB information cannot be displayed or is inaccurate. The DAB station may be temporarily out of service, or the DAB station information is not provided by the DAB broadcaster. Remedy See page Change the antenna height, direction, or place of installation. 13 Contact the DAB broadcaster. ― ■ Bluetooth Problem The unit cannot connect to a Bluetooth device. No sound can be heard, or the sound cuts off intermittently. 58 En Possible cause Remedy See page The Bluetooth function is disabled. In the “Setup” menu, set “Bluetooth (On/Off)” to “On”. 50 The unit is connected to a different Bluetooth device. Disconnect the current Bluetooth connection and connect with the desired Bluetooth device. 33 The unit is too far from the Bluetooth device. Move the Bluetooth device closer to this unit. A device emitting electromagnetic waves (such as a microwave oven and a wireless device) may be located nearby. Do not use this unit near devices that emit electromagnetic waves. The Bluetooth device does not support the A2DP protocol. Use a Bluetooth device that supports the A2DP protocol. 62 The connection profile registered in the Bluetooth device may not be functioning correctly for some reason. Delete the connection profile in the Bluetooth device, and then connect the Bluetooth device to this unit. 32 The passkey on the Bluetooth adapter or other device may be set to a code besides “0000”. Use a Bluetooth device on which the passkey is set to “0000”. The volume on the Bluetooth device is too low. Raise the volume on the Bluetooth device. The sound output on the Bluetooth device may not be set to this unit. Select this unit as the output destination on the Bluetooth device. The connection to the Bluetooth device is cut off. Reconnect with the Bluetooth device. The unit is too far from the Bluetooth device. Move the Bluetooth device closer to this unit. A device emitting electromagnetic waves (such as a microwave oven and a wireless device) may be located nearby. Do not use this unit near devices that emit electromagnetic waves. ― ― ― ― 32 32 ― ― Troubleshooting ■ USB/network Remedy See page The USB storage device is not connected to the USB jack securely. Turn off the unit, reconnect your USB device, and turn the unit on again. 39 The file system of the USB storage device is not FAT16 or FAT32. Use a USB storage device with FAT16 or FAT32 format. 62 Folders and files in the USB device cannot be viewed. The data in the USB storage device is protected by the encryption. Use a USB storage device without an encryption function. The network function cannot be used. The network information (IP address) has not been properly acquired. Enable the DHCP server function on your router and set “DHCP” in the “Setup” menu to “On” on the unit. If you want to configure the network parameters manually, make sure that the IP address of this unit is different from that of other devices on the network. The unit does not detect the USB storage device. 62 49 The wireless LAN router (access point) is turned off. Turn on the wireless LAN router (access point). The unit is too far from the wireless LAN router (access point). Set up this unit closer to the wireless LAN router (access point). ― There is an object blocking the signal path between this unit and the wireless LAN router (access point). Set up this unit so that there is a clear signal path between this unit and the wireless LAN router (access point). ― A device emitting electromagnetic waves (such as a microwave oven and a wireless device) may be located nearby. When connecting wirelessly, do not use this unit near devices that emit electromagnetic waves. ― Access to the network is restricted, due to a firewall on the wireless LAN router (access point). Check the firewall settings of the wireless LAN router (access point). ― The media sharing settings on the PC (server) is incorrect. Change the media sharing settings so that this unit can access the folder on the PC (server). 34 Access is restricted due to the security settings on the PC (server) or router. Check the security settings on the computer (server) and wireless LAN router (access point). ― This unit and the PC (server) are not connected to the same network. Check the network and router settings, to make sure that they are connected to the same network. ― The files on the PC (server) cannot be viewed (played back). The file format may not be compatible with this unit or with the PC (server). Use a file format that is compatible with this unit and with the PC. For details on supported file formats, see “Supported file formats”. Internet radio cannot be played. The selected Internet radio station is currently not available. There may be a network problem at the radio station, or the service may have been stopped. Try the station later or select another station. ― The selected Internet radio station is currently broadcasting silence. Some Internet radio stations broadcast silence at certain of times of the day. Try the station later or select another station. ― Access to the network is restricted due to the firewall settings on a network device, such as a wireless LAN router (access point). Check the firewall settings of your network devices. The Internet radio can be played only when it passes through the port designated by each radio station. The port number varies depending on the radio station. ― The unit cannot connect to the Internet via wireless LAN router (access point). A wireless network cannot be found. The PC (server) cannot be detected. ― 62 59 En ADDITIONAL INFORMATION Possible cause English Problem Troubleshooting Problem Possible cause Remedy See page The network separator function on the wireless LAN router (access point) may be preventing this unit from being accessed. When connecting to this unit with an iPhone, use an SSID on which this unit can be accessed (try connecting via the primary SSID). ― This unit cannot be detected when using AirPlay on an iPhone. A wireless LAN router (access point) that supports multiple SSIDs is used. The unit is not detected when using a dedicated application on a mobile device. This unit and the mobile device are not connected to the same network. Check the network and router settings, to make sure that they are connected to the same network. ― A wireless LAN router (access point) that supports multiple SSIDs is used. The network separator function on the wireless LAN router (access point) may be preventing this unit from being accessed. When connecting to this unit with a mobile device, use an SSID on which this unit can be accessed (try connecting via the primary SSID). ― Firmware update via the network is failed. The network connection is no good. Try connecting again after a while, or a USB storage device to update the firmware. 53 The unit cannot connect to the wireless LAN router (access point). MAC address filtering is enabled on the wireless LAN router (access point). This unit cannot connect to the wireless LAN router (access point) if its MAC address filtering is enabled. Change the settings on the wireless LAN router (access point) to allow this unit to connect. ― 60 En Error indications on the front display Error indications on the front display Message Possible cause Remedy Access denied Access to the PC is denied. Configure the sharing settings and select the unit as a device to which music contents are shared (p. 34). Access error The unit cannot access the USB device. Turn off the unit and reconnect your USB device. If the problem persists, try another USB device. The unit cannot access the iPod. Turn off the iPod and turn it on again. The connected iPod is not supported by the unit. Use an iPod supported by the unit (p. 62). There is a problem with the signal path from the network to the unit. Make sure your router and modem are turned on. Check SP Wires The speaker cables short circuit. Twist the bare wires of the cables firmly and connect to the unit and speakers properly. No content There are no playable files in the selected folder. Select a folder that contains files supported by the unit. Please wait The unit is preparing for connecting to the network. Wait until the message disappears. If the message stays more than 3 minutes, turn off the unit and turn it on again. Unable to play The unit cannot play back the songs stored on the iPod for some reason. Check the song data. If it cannot be played on the iPod itself, the song data or storage area may be defective. The unit cannot play back the songs stored on the PC for some reason. Check if the format of files you are trying to play is supported by the unit. For information about the formats supported by the unit, see “Playing back music stored on media servers (PCs/NAS)” (p. 34). If the unit supports the file format, but still cannot play back any files, the network may be overloaded with heavy traffic. Firmware update is failed. Update the firmware again. ADDITIONAL INFORMATION English Version error Check the connection between the unit and your router (or hub) (p. 14). 61 En Supported devices and file formats Supported devices ■ Bluetooth device • This unit supports Bluetooth devices that support A2DP audio profile and AVRCP control profile. • Bluetooth device may not be detected by the unit or some feature may not be compatible, depending on the model. ■ USB storage device • This unit supports USB mass storage class devices (e.g., flash memories or portable audio players) using FAT16 or FAT32 format. • USB storage devices with encryption cannot be used. • Some features may not be compatible, depending on the model or manufacturer of the USB storage device. ■ AirPlay • AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac with OS X Mountain Lion or later, and Mac and PC with iTunes 10.2.2 or later. • Made for. iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s iPad Pro (9.7" and 12.9"), iPad mini 4, iPad Air 2, iPad mini 3, iPad Air, iPad mini 2, iPad mini, iPad (3rd and 4th generation), iPad 2 iPod touch (5th and 6th generation) (as of June 2017) Supported file formats ■ USB/PC (NAS) File Sampling frequency (kHz) Quantization bitrate (bit) Bitrate Gapless playback 16/24 ― ✔ WAV * 32/44.1/48/88.2/96/176.4/192 MP3 32/44.1/48 ― 8 to 320 ― WMA 32/44.1/48 ― 8 to 320 ― MPEG-4 AAC 32/44.1/48 ― 8 to 320 ― FLAC 32/44.1/48/88.2/96/176.4/192 16/24 ― ✔ ALAC 32/44.1/48/88.2/96 16/24 ― ✔ AIFF 32/44.1/48/88.2/96/176.4/192 16/24 ― ✔ DSD 2.8MHz/5.6MHz 1 ― ― * Linear PCM format only Note • To play back FLAC files stored on a PC or NAS, you need to install server software that supports sharing of FLAC files via DLNA on your PC or use a NAS that supports FLAC files. • Digital Rights Management (DRM) contents cannot be played back. 62 En Trademarks Trademarks DLNA™ and DLNA CERTIFIED™ are trademarks or registered trademarks of Digital Living Network Alliance. All rights reserved. Unauthorized use is strictly prohibited. Windows™ Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Internet Explorer, Windows Media Audio and Windows Media Player are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Bluetooth protocol stack (Blue SDK) Copyright 1999-2014 OpenSynergy GmbH All rights reserved. All unpublished rights reserved. MusicCast is a trademark or registered trademark of Yamaha Corporation. Yamaha Eco-Label is a mark that certifies products of high environmental performance. (For R-N803D) The unit supports DAB/DAB+ tuning. Explanations regarding GPL This product utilizes GPL/LGPL open-source software in some sections. You have the right to obtain, duplicate, modify, and redistribute this open-source code only. For information on GPL/ LGPL open source software, how to obtain it, and the GPL/LGPL license, refer to the Yamaha Corporation website (http://download.yamaha.com/sourcecodes/musiccast/). Android™ Google Play™ Android and Google Play are trademarks of Google Inc. English The Wi-Fi CERTIFIED™ Logo is a certification mark of Wi-Fi Alliance®. The Wi-Fi Protected Setup™ Identifier Mark is a certification mark of Wi-Fi Alliance®. ADDITIONAL INFORMATION Supports iOS 7 or later for setup using Wireless Accessory Configuration. “Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance. iTunes, AirPlay, iPad, iPhone, iPod, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. iPad Air and iPad mini are trademarks of Apple Inc. App Store is a service mark of Apple Inc. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under license. 63 En Specifications Network • • • • • • • Input jack: NETWORK x 1 (100Base-TX/10Base-T) PC client function Compatible with DLNA ver. 1.5 AirPlay supported Internet radio Streaming service Wi-Fi function Capable of direct connection with mobile device Available security method ....................................... WEP, WPA2-PSK(AES), Mixed Mode Radio frequency band ....................................................... 2.4 GHz Radio frequency (operational frequency) .............................................................. 2412 MHz to 2472 MHz Maximum output power (E.I.R.P) ............... 17.5 dBm (56.2 mW) Wireless network standard ................................IEEE 802.11 b/g/n Wi-Fi settings WPS (Wi-Fi Protected Setup) ..............................Capable of WPS Capable of sharing with iOS devices by wireless connection. • • • • • • Bluetooth related function • Version..............................................................Bluetooth 2.1 + EDR • Frequency............................................................................. 2.4 GHz • Radio frequency (operational frequency) .................................................................... 2402 MHz to 2480 MHz • Maximum output power (E.I.R.P)....................... 4.0 dBm (2.5 mW) • Wireless output...................................................... Bluetooth Class 2 • Profiles Source function The unit → sink device (ex. Bluetooth headphones) Profile: A2DP version 1.3, AVRCP version 1.6 CODEC: SBC Sink function The unit ← source device (ex. iPhone/Android) Profile: A2DP version 1.3, AVRCP version 1.6 CODEC: SBC, AAC USB • Input jack: USB x 1 (USB 2.0) • Capable of mass storage class USB memory • Current supply capacity: 1.0 A Audio • Minimum RMS output power (20 Hz to 20 kHz, 0.019% THD, 8Ω) .....................100 W+100 W • Dynamic power per channel (IHF) (8/6/4/2) ........................................................................... 140/170/220/290 W • Maximum power per channel (1 kHz, 0.7% THD, 4Ω) [U.K. and Europe models] ...................................................160 W • IEC power (1 kHz, 0.04% THD, 8Ω) [U.K. and Europe models] ...................................................115 W • Power band width (main L/R) (0.06%THD 40.0 W, 8Ω) ..................................... 10 Hz to 50 kHz • Damping factor (SPEAKERS A) 1 kHz, 8 .................................................................... 240 or more • Maximum effective output power (JEITA) (1 kHz, 10% THD, 8) [Asia and General models]...................................................145 W • Input sensitivity/input impedance PHONO (MM) ........................................................ 2.5 mV/47 kΩ CD, etc. ................................................................. 200 mV/47 k • Maximum input signal PHONO (MM) (1 kHz, 0.03% THD) ................................. 45 mV CD, etc. (1 kHz, 0.5% THD)..................................................2.2 V • Output level/output impedance CD, etc. (input 1 kHz, 200 mV) OUT ................................................................... 200 mV/1.0 k SUBWOOFER OUT.............................................. 4.0 V/1.2 kΩ 64 En • • • • (Cut off frequency) ........................................................... 90 Hz PHONES (8 load) ..............................................470 mV/470 Frequency response CD, etc. (20 Hz to 20 kHz) ........................................... 0 ± 0.5 dB CD, etc. (10 Hz to 100 kHz, PURE DIRECT on) ........ 0 ± 1.0 dB RIAA equalization deviation PHONO (MM).................................................................. ± 0.5 dB Total harmonic distortion PHONO (MM) to OUT (20 Hz to 20 kHz, 2.5 V) ....................................... 0.03% or less CD, etc. to SPEAKERS (20 Hz to 20 kHz, 50.0 W, 8)............................ 0.019% or less Signal to noise ratio (IHF-A Network) PHONO (MM) (input shorted, 5 mV) [U.S.A., Canada, Asia, General models]..............82 dB or more [U.K., Europe, Korea, Australia models] .............75 dB or more CD, etc. (input shorted, 200 mV) ..........................100 dB or more Residual noise (IHF-A network) .............................................70 µV Channel separation CD, etc. (5.1 k input shorted, 1 kHz/10 kHz) .........................................................................65/50 dB or more Tone control characteristics BASS Boost/cut (20 Hz) ........................................................... ± 10 dB Turnover frequency ......................................................... 300 Hz TREBLE Boost/cut (20 kHz) ........................................................ ± 10 dB Turnover frequency ........................................................ 3.0 kHz Continuous loudness control Attenuation 1 kHz................................................................ -30 dB Gain tracking error (+16.5 to -80 dB) ......................... 0.5 dB or less Digital input (OPTICAL/COAXIAL) Support audio sample rate ..........32/44.1/48/88.2/96/176.4/192 kHz FM • Tuning range [U.S.A. and Canada models] ...........................87.5 to 107.9 MHz [Asia and General models] ....... 87.5/87.50 to 108.0/108.00 MHz [U.K., Europe, Korea, Australia models] ....87.50 to 108.00 MHz • 50 dB quieting sensitivity (IHF, 1 kHz, 100% MOD.) Mono ................................................................. 3.0 µV (20.8 dBf) • Signal to noise ratio (IHF) Mono/stereo ...............................................................69 dB/67 dB • Harmonic distortion (1 kHz) Mono/stereo ................................................................. 0.5%/0.6% • Antenna input ..........................................................75Ω unbalanced AM (R-N803) • Tuning range [U.S.A. and Canada models] .............................. 530 to 1710 kHz [Asia and General models] ................. 530/531 to 1710/1611 kHz [Korea model]...................................................... 531 to 1611 kHz DAB (R-N803D) • Tuning range ...........................................174 to 240 MHz (Band III) • Support audio format .............................MPEG 1 Layer II/MPEG 4 HE AAC v2 (AAC+) • Antenna input ..........................................................75Ω unbalanced General • Power supply [U.S.A. and Canada models] ............................. AC 120 V, 60 Hz [General model] .......................AC 110-120/220-240 V, 50/60 Hz [Korea model]..................................................... AC 220 V, 60 Hz [Australia model] ............................................... AC 240 V, 50 Hz [U.K. and Europe models] ................................. AC 230 V, 50 Hz [Asia model] ......................................... AC 220-240 V, 50/60 Hz • Power consumption ................................................................ 250 W • Off mode.................................................................................. 0.1 W Specifications • Standby power consumption (reference data) ......................... 0.1 W • Network Standby on Wired .................................................................................... 1.7 W Wireless (Wi-Fi/Wireless Direct/Bluetooth)......................... 1.8 W • Maximum power consumption (1 kHz, 8Ω, 10% THD) [Asia and General models] .................................................. 450 W • Dimensions (W  H  D) ................................ 435  151  392 mm (17-1/8"  6"  15-7/16") * Including legs and protrusions • Reference Dimensions (W  H  D) (with wireless antenna upright) ......................................................................... 435  215  392 mm (17-1/8"  8-1/2"  15-7/16") * Including legs and protrusions • Weight..................................................................11.0 kg (24.25 lbs) English ADDITIONAL INFORMATION * The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file. 65 En Index A AC IN jack....................................................................... 7 ADVANCED SETUP menu.......................................... 52 AirPlay........................................................................... 38 AM antenna ................................................................... 13 AM radio ....................................................................... 25 ANTENNA terminals...................................................... 7 Auto Playback, option menu ......................................... 46 Auto preset, FM radio stations ...................................... 25 Auto Preset, option menu .............................................. 46 Automatic playback, PC music content......................... 36 Automatic playback, USB content ................................ 40 Automatic speaker settings............................................ 42 AutoPowerStdby (Auto Power Standby), setup menu ................................................................. 51 B BALANCE control........................................................ 23 Banana plug, connection ............................................... 11 BASS control................................................................. 23 Batteries, remote control ................................................. 9 Bi-wire connection ........................................................ 12 Bluetooth device playback ............................................ 32 Bluetooth indicator .......................................................... 6 Bluetooth, setup menu ................................................... 50 C CD jacks .......................................................................... 7 CD player, connection ................................................... 10 Clear Preset, option menu.............................................. 46 Clearing preset station ................................................... 27 COAXIAL jacks.............................................................. 7 Connection, Network, setup menu ................................ 48 Control Knob, front display message ............................ 44 D DAB antenna ................................................................. 13 DAB radio ..................................................................... 29 DIMMER......................................................................... 4 Disconnect MIC, front display message........................ 43 Disconnection, Bluetooth connection............................ 33 DLNA ............................................................................ 34 DMC Control, Network, setup menu ............................ 49 DVD player, connection................................................ 10 E ECO Mode, setup menu ................................................ 51 [ENTER]:Start, front display message .......................... 43 Error messages, YPAO.................................................. 44 F Firmware update via network........................................ 54 Firmware update, ADVANCED SETUP menu ............ 53 Firmware version, ADVANCED SETUP menu ........... 52 FM antenna.................................................................... 13 FM radio ........................................................................ 25 66 En Front display ................................................................... 6 Front display, switching information............................ 22 H HOME, remote control ................................................... 8 I Information, Network, setup menu ............................... 48 INIT, ADVANCED SETUP menu............................... 53 Initialize, ADVANCED SETUP menu......................... 53 Initiate Scan, option menu ............................................ 46 Input selection keys, remote control ............................... 8 INPUT selector ............................................................... 5 Internal Error, front display message............................ 44 Internet radio................................................................. 37 iOS device setting sharing, wireless network connection..................................... 16 IP Address, Network, setup menu ................................ 49 iPod content playback, AirPlay .................................... 38 iTunes content playback, AirPlay................................. 38 L Level Error, front display message ............................... 45 LINE jacks ...................................................................... 7 LOUDNESS control ..................................................... 24 M Manual preset, FM/AM radio stations.......................... 26 Manual setting, wireless network connection............... 18 Media sharing setup ...................................................... 34 Message, front display .................................................. 61 MusicCast ..................................................................... 20 MUTE ............................................................................. 6 N NAS content playback .................................................. 34 Network cable, connection ........................................... 14 Network connection...................................................... 15 NETWORK jack............................................................. 7 Network Name, Network, setup menu.......................... 49 Network, setup menu .................................................... 48 No MIC, front display message .................................... 44 No Signal, front display message ................................. 44 No SPEAKERS, front display message........................ 44 No Warning, front display message.............................. 43 Noisy, front display message ........................................ 44 NOW PLAYING, remote control................................... 8 O OPTICAL jacks .............................................................. 7 Option menu ................................................................. 46 Out of Phase, front display message............................. 45 Over Distance, front display message........................... 45 P Pairing, Bluetooth device.............................................. 32 PCs content playback.................................................... 34 Index PHONES jack ................................................................. 5 PHONES, front display message .................................. 44 PHONO jacks ................................................................. 7 Playback keys ................................................................. 9 Playback, Bluetooth device contents ............................ 32 Playing back, PCs/NAS content ................................... 34 Playing back, USB content ........................................... 39 Power cord, connection ................................................ 14 Power indicator ............................................................... 4 Preset function, DAB.................................................... 30 Preset, song/streaming station ...................................... 41 PURE DIRECT switch ................................................. 23 Pure Direct, front display message ............................... 44 R Radio Data System tuning ............................................ 28 Remote control ID, ADVANCED SETUP menu......... 52 Repeat playback, AirPlay ............................................. 38 Repeat playback, PC music content.............................. 35 Repeat playback, USB content ..................................... 40 Result Info., front display message............................... 43 RETURN ........................................................................ 5 VOLUME control ........................................................... 5 Volume Trim, option menu........................................... 46 Volume, setup menu ..................................................... 50 W WAC ............................................................................. Warning messages, YPAO............................................ Wireless antenna ........................................................... Wireless Direct.............................................................. WPS push button configuration, wireless network connection ..................................... 15 45 14 19 17 Y YPAO............................................................................ 42 YPAO VOL..................................................................... 6 YPAO, setup menu ....................................................... 50 S ADDITIONAL INFORMATION SELECT/ENTER............................................................ 5 Setup menu ................................................................... 47 Shuffle playback, AirPlay............................................. 38 Shuffle playback, PC music content ............................. 35 Shuffle playback, USB content..................................... 40 Signal Info., option menu ............................................. 46 Signal strength indicator ................................................. 6 SLEEP............................................................................. 6 Sleep timer .................................................................... 24 SP IMP., ADVANCED SETUP menu ......................... 52 Speaker impedance, ADVANCED SETUP menu........ 52 Speaker, connection...................................................... 10 SPEAKERS A/B............................................................. 5 SPEAKERS terminals .................................................... 7 Standby (Network Standby), Network, setup menu ..... 49 STEREO ......................................................................... 6 SUBWOOFER OUT jack............................................... 7 Subwoofer, connection ................................................. 10 T TREBLE control ........................................................... 23 TRIGGER OUT jacks..................................................... 7 Tune Aid, option menu ................................................. 46 TUNED........................................................................... 6 Turntable, connection ................................................... 10 Update (Network Update), Network, setup menu ........ UPDATE, ADVANCED SETUP menu ....................... USB content playback .................................................. User Cancel, front display message.............................. English U 50 53 39 44 V Verification, network connection ................................. 20 VERSION, ADVANCED SETUP menu ..................... 52 Vol.Interlock (Volume interlock), option menu ........... 46 67 En Information for users on collection and disposal of old equipment and used batteries: These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. For business users in the European Union: If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. Information on Disposal in other Countries outside the European Union: These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the EU Battery Directive for the chemical involved. (weee_battery_eu_en_02) 68 En EN English CS Czech SIMPLIFIED EU DECLARATION OF CONFORMITY Hereby, Yamaha Music Europe GmbH declares that the radio equipment type [R-N803D] is in compliance with Directive 2014/ 53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://europe.yamaha.com/en/support/compliance/doc.html ZJEDNODUŠENÉ EU PROHLÁŠENÍ O SHODĚ Tímto Yamaha Music Europe GmbH prohlašuje, že typ rádiového zařízení [R-N803D] je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: https://europe.yamaha.com/en/support/compliance/doc.html FR DA French Danish DECLARATION UE DE CONFORMITE SIMPLIFIEE Le soussigné, Yamaha Music Europe GmbH, déclare que l'équipement radioélectrique du type [R-N803D] est conforme à la directive 2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l'adresse internet suivante: https://europe.yamaha.com/en/support/compliance/doc.html FORENKLET EU-OVERENSSTEMMELSESERKLÆRING Hermed erklærer Yamaha Music Europe GmbH, at radioudstyrstypen [R-N803D] er i overensstemmelse med direktiv 2014/53/EU. EU-overensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: https://europe.yamaha.com/en/support/compliance/doc.html DE ET German Estonian VEREINFACHTE EU-KONFORMITÄTSERKLÄRUNG Hiermit erklärt Yamaha Music Europe GmbH, dass der Funkanlagentyp [R-N803D] der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: https://europe.yamaha.com/en/support/compliance/doc.html LIHTSUSTATUD ELI VASTAVUSDEKLARATSIOON Käesolevaga deklareerib Yamaha Music Europe GmbH, et käesolev raadioseadme tüüp [R-N803D] vastab direktiivi 2014/53/ EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: https://europe.yamaha.com/en/support/compliance/doc.html SV EL Swedish Greek FÖRENKLAD EU-FÖRSÄKRAN OM ÖVERENSSTÄMMELSE Härmed försäkrar Yamaha Music Europe GmbH att denna typ av radioutrustning [R-N803D] överensstämmer med direktiv 2014/ 53/EU. Den fullständiga texten till EU-försäkran om överensstämmelse finns på följande webbadress: https://europe.yamaha.com/en/support/compliance/doc.html ΑΠΛΟΥΣΤΕΥΜΕΝΗ ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ΕΕ Με την παρούσα ο/η Yamaha Music Europe GmbH, δηλώνει ότι ο ραδιοεξοπλισμός [R-N803D] πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: https://europe.yamaha.com/en/support/compliance/doc.html IT HR Italian Croatian DICHIARAZIONE DI CONFORMITÀ UE SEMPLIFICATA Il fabbricante, Yamaha Music Europe GmbH, dichiara che il tipo di apparecchiatura radio [R-N803D] è conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: https://europe.yamaha.com/en/support/compliance/doc.html POJEDNOSTAVLJENA EU IZJAVA O SUKLADNOSTI Yamaha Music Europe GmbH ovime izjavljuje da je radijska oprema tipa [R-N803D] u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: https://europe.yamaha.com/en/support/compliance/doc.html ES LV Spanish Latvian DECLARACIÓN UE DE CONFORMIDAD SIMPLIFICADA Por la presente, Yamaha Music Europe GmbH declara que el tipo de equipo radioeléctrico [R-N803D] es conforme con la Directiva 2014/53/UE. El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: https://europe.yamaha.com/en/support/compliance/doc.html VIENKĀRŠOTA ES ATBILSTĪBAS DEKLARĀCIJA Ar šo Yamaha Music Europe GmbH deklarē, ka radioiekārta [R-N803D] atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: https://europe.yamaha.com/en/support/compliance/doc.html NL LT Dutch Lithuanian VEREENVOUDIGDE EU-CONFORMITEITSVERKLARING Hierbij verklaar ik, Yamaha Music Europe GmbH, dat het type radioapparatuur [R-N803D] conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: https://europe.yamaha.com/en/support/compliance/doc.html SUPAPRASTINTA ES ATITIKTIES DEKLARACIJA Aš, Yamaha Music Europe GmbH, patvirtinu, kad radijo įrenginių tipas [R-N803D] atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: https://europe.yamaha.com/en/support/compliance/doc.html BG HU Bulgarian ОПРОСТЕНА ЕС ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ С настоящото Yamaha Music Europe GmbH декларира, че този тип радиосъоръжение [R-N803D] е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: https://europe.yamaha.com/en/support/compliance/doc.html Hungarian EGYSZERŰSÍTETT EU-MEGFELELŐSÉGI NYILATKOZAT Yamaha Music Europe GmbH igazolja, hogy a [R-N803D] típusú rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: https://europe.yamaha.com/en/support/compliance/doc.html 69 En PL Polish UPROSZCZONA DEKLARACJA ZGODNOŚCI UE Yamaha Music Europe GmbH niniejszym oświadcza, że typ urządzenia radiowego [R-N803D] jest zgodny z dyrektywą 2014/ 53/UE. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: https://europe.yamaha.com/en/support/compliance/doc.html PT Portuguese DECLARAÇÃO UE DE CONFORMIDADE SIMPLIFICADA O(a) abaixo assinado(a) Yamaha Music Europe GmbH declara que o presente tipo de equipamento de rádio [R-N803D] está em conformidade com a Diretiva 2014/53/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: https://europe.yamaha.com/en/support/compliance/doc.html RO Romanian DECLARAȚIA UE DE CONFORMITATE SIMPLIFICATĂ Prin prezenta, Yamaha Music Europe GmbH declară că tipul de echipamente radio [R-N803D] este în conformitate cu Directiva 2014/53/UE. Textul integral al declarației UE de conformitate este disponibil la următoarea adresă internet: https://europe.yamaha.com/en/support/compliance/doc.html SK Slovak ZJEDNODUŠENÉ EÚ VYHLÁSENIE O ZHODE Yamaha Music Europe GmbH týmto vyhlasuje, že rádiové zariadenie typu [R-N803D] je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: https://europe.yamaha.com/en/support/compliance/doc.html SL Slovenian POENOSTAVLJENA IZJAVA EU O SKLADNOSTI Yamaha Music Europe GmbH potrjuje, da je tip radijske opreme [R-N803D] skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: https://europe.yamaha.com/en/support/compliance/doc.html FI Finnish YKSINKERTAISTETTU EUVAATIMUSTENMUKAISUUSVAKUUTUS Yamaha Music Europe GmbH vakuuttaa, että radiolaitetyyppi [R-N803D] on direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: https://europe.yamaha.com/en/support/compliance/doc.html TR Turkey BASİTLEŞTİRİLMİŞ AVRUPA BİRLİĞİ UYGUNLUK BİLDİRİMİ İşbu belge ile, Yamaha Music Europe GmbH, radyo cihaz tipinin [R-N803D], Direktif 2014/53/AB'ye uygunluğunu beyan eder. AB uyumu beyanının tam metni aşağıdaki internet adresinden edinilebilir: https://europe.yamaha.com/en/support/compliance/doc.html 70 En Yamaha Global Site https://www.yamaha.com/ Yamaha Downloads http://download.yamaha.com/ Manual Development Group © 2017 Yamaha Corporation Published 06/2017 AM-A0 10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650 Japan AV16-0039
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75

Yamaha R-N803 de handleiding

Categorie
Audiotuners
Type
de handleiding
Deze handleiding is ook geschikt voor