Aiphone JK-1MED Handleiding

Merk: Aiphone

Model: JK-1MED

Categorie: Deur intercom systemen

Type: Handleiding

FK1462 P0109YI

JK-1MED

HANDS FREE COLOR VIDEO INTERCOM MASTER MONITOR STATION

INTERPHONE VIDEO COULEUR MAINS LIBRES MONITEUR MAÎTRE

HANDENVRIJE KLEURENVIDEOFONIE MONITOR-HOOFDPOST

JK-1MED

Master monitor station

Moniteur maître

Monitor-hoofdpost

INSTALLATION & OPERATION MANUAL

MANUEL D

’

INSTALLATION ET D

’

UTILISATION

INSTALLATIE- EN GEBRUIKSHANDLEIDING

- 2 -

EnglishFrançais

Nederlands

PRECAUTIONS

General Prohibitions Prohibition to Dismantle the Unit Prohibition on Subjecting the Unit to Water General Precautions

WARNING

(Negligence could result in death or serious injury.)

1. High voltage is present internally. Do not open the case. Electric shock could result.

2. Do not dismantle or alter the unit. Fire or electric shock could result.

3. Do not connect any non-speciﬁed power source to the +, - terminals. Also, do not

install two power supplies in parallel to a single input. Fire or damage to the unit

could result.

4. Keep the unit away from water or any other liquid. Fire or electric shock could result.

5. Do not put any metal or ﬂammable material into the unit through the openings. Fire

or electric shock could result.

6. Do not use power supply with a voltage other than speciﬁed. Fire or electric shock

could result.

7. Do not connect any terminal on the unit to an AC power line. Fire or electric shock

could result.

CAUTION

(Negligence could result in injury to people or damage to property.)

1. Do not install or make any wire terminations while power supply is plugged in. It

can cause electrical shock or damage to the unit.

2. Before turning on power, make sure wires are not crossed or shorted. If not, ﬁre or

electric shock could result.

3. When mounting the unit on a wall, install the unit in a convenient location, but not

where it could be jarred or bumped. Injury could result.

4. For power supply, use Aiphone power supply model or model speciﬁed for use

with system. If non-speciﬁed product is used, ﬁre or malfunction could result.

5. Do not install the unit in any of the following locations. Fire, electric shock, or unit

trouble could result.

* Places under direct sunlight or places near heating equipment that varies in

temperature.

* Places subject to dust, oil, chemicals, etc.

* Places subject to moisture and humidity extremes, such as bathrooms, cellars,

greenhouses, etc.

* Places where the temperature is quite low, such as

inside a refrigerated area or in

front of an air conditioner.

* Places subject to steam or smoke (near heating or cooking surfaces).

* Where noise generating devices such as dimmer switches or inverter electrical

appliances are close by.

* Do not install the unit in locations subject to frequent vibration or impact.

6. Do not put anything on the unit or cover the unit with cloth, etc. Fire or unit trouble

could result.

7. Do not press on the LCD or subject it to a high impact. The LCD glass could be

punctured and result in an injury.

8. If the LCD is punctured, do not allow skin contact with the liquid crystal inside.

Inﬂammation could result.

* If liquid crystal is ingested, immediately gargle with water and seek medical

attention.

* If contact with the eyes or skin occurs, clean with pure water for at least 15 minutes

and seek medical attention.

General Precautions

1. Keep the unit more than 1 m away from radio or TV set.

2. This

unit is for indoor use only. Do not use outdoors.

3. In areas where broadcasting station antennas are close by, the intercom system may be

affected by radio frequency interference.

4. As to other manufacturer's devices (such as sensor, detectors, door releases) used

with this system, comply with the Speciﬁcations and Warranty conditions that the

manufacturers or venders present.

5. Keep the intercom

wires at least 30 cm (12") away from AC 100-240 V lines. Noise

and malfunction could result.

6. If the unit is down or does not operate properly, unplug the power supply or turn off

the JK-1MED and JK-1HD (JK-1SD) POWER switches.

7. The unit is for wall-mount use only. For desktop applications, use desk stand.

8. When wall-mounted, the top of the unit may darken. This does not indicate a

malfunction

9. The unit case may become warm with use, but this is not a unit malfunction.

10. If a cellular phone is used close by, the unit may malfunction.

11. The LCD panel is manufactured with very high precision techniques. Small portions

of the panel may fail to light up or some portions may be constantly lit, but this does

not indicate a unit malfunction. Please be aware of this in advance.

12. Refrain

from using the color monitor station in sunlit areas.

13. At night, due to reduced lighting on the object, the monitor sees more noise and the

face becomes more difﬁcult to see, but this is not malfunction.

14. Talk within 50 cm (20") or less from the unit. If you stand too far away, it may be

difﬁcult for the other person to hear the communication.

15. If there are loud noises around the unit (such

as music playing or children crying), the

sound may break up and be difﬁcult to hear.

16. During communication, if you speak before the other person has ﬁnished talking, your

voice may not come through clearly. Communication will proceed smoothly if you

wait until the other person has ﬁnished before speaking.

17. At a gate or porch illuminated by a ﬂuorescent lamp, the picture may vary, but this is

not a malfunction.

18. When outside temperature lowers sharply after rainfall, etc., the inside of the camera

may fog up slightly, causing a blurry picture, but this is not a malfunction. Normal

operation will be restored when moisture evaporates.

19. Due to the environmental sound around the unit, it may hinder smooth communication,

but this is not a malfunction.

20. The outline of video images disp

layed by video door station may differ from that of

the actual person(s) or background, but this is not a malfunction.

21. If the screen of a video door station freezes during wintertime, the picture may become

difﬁcult to see or the CALL button may not move, but this is not a malfunction.

22. Aiphone assumes no responsibility for corruption of saved information (such as

changes to or deletion of sa

ved information). Please be aware of this in advance.

23. This unit is not compatible with JA, JF, KB, and KC series units.

24. Warm-color lighting shining on the door station may change the tint of the picture on

the monitor.

PACKAGE CONTENTS

JK-1MED Mounting screws x 2 Wood mounting screws x 2

Option connector Installation & Operation manual

- 3 -

English Français Nederlands

INSTALLATION

2-1 Mounting locations

Install the master monitor station in a place

where the screen is not exposed to direct

sunlight.

The master monitor station has switches on

both sides. Allow at least 5 cm (2") of open

space on either side.

Allow at least 15 cm (6") of vertical open

space from the center of the mounting

bracket in order to mount the master

monitor station.

+ 5 cm

(2")

+ 5 cm

(2")

JK-1MED

+ 15 cm

(6")

2-2 Wiring method, wiring distance

Wire the units from station-to-station (daisy-chained).

0,65 mm 22 AWG

1,0 mm 18 AWG

A 50 m 165' 100 m 330'

B 5 m 16' 10 m 33'

C 75 m 245' 150 m 490'

JK-1HD

JK-1SD

JK-1MED

JK-DA

JK-DV

JK-DVF

2 4

PS18

PS-1820

PS-1810DIN

PS-1820DIN

B C

IER-2

2-3 Cable

Use PVC jacket with PE (polyethylene) insulated cable

(x2)

Never use individual conductors, twisted pair cable or coaxial cable.

When using a cable with unused conductors, terminate both ends of

the unused pair(s) with a 120 resistor .

JK-1MED JK-1HD/JK-1SD

120 120

- 4 -

EnglishFrançais

Nederlands

WIRING

Insert wires securely into each terminal as shown.

JK-1HD

JK-1MED

EL-12S

IER-2

A1 A2

JK-DVFJK-DV

JK-DA

DOOR

PS-1820

PS-1810DIN/

PS-1820DIN

230V AC

18V DC 1A (PS-1810DIN)

18V DC 2A (PS-1820DIN)

IN 230V~ 50/60Hz

100V - 240V -

50/60 Hz

18V DC

2 A

V -

V +

[1]

[2]

[3]

(BR)

(RD)

(OR)

(YE)

(GR)

(BL)

DC 18 V

JK-1SD

OPTION

CONNECTOR

OPTION

CONNECTOR

PS18 PS18

JK-1MED JK-1HD

BR: Brown

RD: Red

OR: Orange

YE: Yellow

GR: Green

BL: Blue

JK-1MEDJKW-BA

JK-DA

JK-DV

JK-DVF

PS18

JK-1HD

JK-1SD

Video door station

Door release

An EL-12S (AC 12 V 0.125 A, DC 12 V 0.2 A) or equivalent part and a separate AC transformer are required.

Run separate cables for audio/video and door release.

Door release contact: AC/DC 24 V, 0.5 A (Minimum Contact : 100 mV DC, 0.1 mA)

(N/O dry closure contact L, L).

AC transformer

Optional call extension speaker

IER-2

Power supply

Master monitor station

NP:

Non-polarized

Pol

arized

Presence of sound from IER-2

Item Sound

Chime tone from door station (8-1)

Alarm sound during external sensor

input (8-15)

Audio during instant voice call (8-1)

Chime tone during room-to-room

communication (8-4)

- 5 -

English Français Nederlands

WIRING

Insert wires securely into each terminal as shown.

JK-1HD

JK-1MED

EL-12S

IER-2

A1 A2

JK-DVFJK-DV

JK-DA

DOOR

PS-1820

PS-1810DIN/

PS-1820DIN

230V AC

18V DC 1A (PS-1810DIN)

18V DC 2A (PS-1820DIN)

IN 230V~ 50/60Hz

100V - 240V -

50/60 Hz

18V DC

2 A

V -

V +

[1]

[2]

[3]

(BR)

(RD)

(OR)

(YE)

(GR)

(BL)

DC 18 V

JK-1SD

OPTION

CONNECTOR

OPTION

CONNECTOR

PS18 PS18

JK-1MED JK-1HD

BR: Brown

RD: Red

OR: Orange

YE: Yellow

GR: Green

BL: Blue

JK-1MEDJKW-BA

JK-DA

JK-DV

JK-DVF

PS18

JK-1HD

JK-1SD

Option connector: Control external devices connected with the option connector.

[1] Video signal output: Video can be output to DVR, etc.

(NTSC, 1 Vp-p/75 ) Wiring distance: 3 m

NOTES: When a video signal is output, the monitor station may produce

a buzzing sound depending on the installation environment.

A video signal is only output during calling from a door station to the JK-

1MED/during communication between a door station and the JK-1MED/during

monitoring from the JK-1MED (screen playing recorded pictures is not output).

[2] Options output

(AC/DC 24 V, 1.6 A N/O dry closure contact)

(Minimum Contact : 100 mV DC, 0.1 mA)

Sub master

monitor station

Audio only sub master station

Optional long distance adaptor JKW-BA

Use the long distance adaptor JKW-BA within the distance ranges shown in the table when the wiring distance between the door station and the furthest inside unit is

longer than the distance in 2-2 on p. 3.

To prevent shorts, be sure to cut unused lead wires at the bottom and

insulate the ends.

Ø 0.65 mm 22 AWG Ø 1.0 mm 18 AWG

A 100 m 330' 200 m 650'

B 50 m 165' 100 m 330'

C 50 m 165' 100 m 330'

D 5 m 16' 10 m 33'

[3] External sensor input settings are required.

External sensor input speciﬁcations

Input method

N/O dry closure contact

External sensor input

(start signal only detection method)

Detection

conﬁrmation time

100 mS or more

Contact resistance

During N/O dry closure: Less than 700

During N/C dry closure: At least 3 k

Terminal short

current

Less than 10 mA

Voltage between

terminals

Less than DC 20 V

(when open between terminals)

When the JK-1HD is connected, split

power between the master station and

the sub master station if radio signals are

picked up during communication.

NP:

Non-polarized

Polarized

(To optional units)

- 6 -

EnglishFrançais

Nederlands

MOUNTING

Back wiring

JK-1MED

8mm

(3/8")

1. Press RELEASE button

(to insert or remove the wire).

2. Insert the cable into the terminal.

Mounting screws x 2

1-gang box

83,5 mm

(3-5/16")

Mounting bracket

Surface wiring

* When a 1-gang box is not mounted, the cable can be routed as surface wiring to the top or

bottom of the unit. Cut a cable inlet on the upper part of the unit to allow passage of the

wiring into the unit.

PS-1810DIN/

PS-1820DIN

PS-1820

Mounting bracket

1-gang box

Din rail

83,5 mm

(3-5/16")

* To pass the cable through the back of the

unit, cut out the cable inlet.

Wood

mounting

screws x 2

Mounting bracket

83,5 mm

(3-5/16")

NAMES

JK-1MED

Play LED (red)

PLAY button

Record LED (red)

RECORD button

POWER switch

Speaker

MONITOR button

OFF button

TALK button

Transmit LED (red)

Option button (*)

CALL button

ADJUST button

ZOOM/WIDE button

PAN/TILT button

MENU button

Menu LED (red)

DOOR RELEASE button

Door release LED (red)

Microphone

Color LCD video monitor

Screen brightness control

(0 10)

Receive volume control

(0 10)

Chime tone volume

(0 10)

(*) The option butto

n controls connected option

units such as turning lighting on and off and

activation of added door releases.

- 7 -

English Français Nederlands

OPERATING METHOD

To operate this unit, check the symbol and then press the appropriate operation button

This is not a touch-panel operation.

Do not press on the LCD or subject it to high

impact.

The LCD glass could break which could

result in an injury.

Symbol

The symbols differ according to the symbol

screen.

Operation buttons:

Press to select the symbol that is displayed

on the screen.

* The name of the operation button may

differ from the name of the symbol.

To operate a symbol, press the operation

button that is below the symbol.

Example:

To activate manual recording, press

RECORD button below the symbol

* In the manual, an explanation is given using

the

REC

button ( ).

SETTING UP

Upon initial installation, set the time ﬁrst. If the unit is used without setting the time, the menu LED (red) will light up as notiﬁcation.

When power has not been supplied for at least 3 hours, the time setting will return to the initial setting and the menu LED may ﬂash. Reset the

time again.

If there are no operations for approximately 1 minute during the setup mode, the setting will end autom

atically. If the settings are incomplete, start

again from the beginning.

Symbol Function description

To manually record.

To return to the screen of the previous

operation.

To display the previous (more recent

date) picture.

To play the recorded pictures.

To display the next (older date) picture.

To save or erase an image.

To erase a recorded image.

To fast forward the play screen.

To pause the play screen.

To advance the play screen frame by

frame.

To reverse the play screen frame by

frame.

To erase the display.

To save recorded pictures.

Setting can also be done by pressing

ZOOM/WIDE button.

Main symbols and function descriptions

In the standby mode, press MENU button until the setting screen

is displayed (approximately 1 second).

> 1Sec.

Press



button or



button to select "INITIAL SETTING", and

press MENU button ( ).

Press



button or



button to select the item you want to set or

check, and set with the

MENU button ( ).

SET THE DATE/TIME

To set the year, date, and time.

SET EXTERNAL INPUT

SETTING

To set the external input.

SELECT THE LANGUAGE

To select the language used.

RESTORE DEFAULT

SETTING

To initialize the settings.

When completing the time setting, press OFF button to return to

the standby mode. In other cases, set by pressing

MENU button

(

). Press REC button ( ) to cancel the setting and return

to the previous screen.

7-1 Setting screens and display methods

- 8 -

EnglishFrançais

Nederlands

7-3 SET THE DATE/TIME

After performing steps 1 and 2 in section 7-1, select "DATE/TIME"

and press MENU button

( )

In the "ADJUST DATE/TIME" screen, press



button or



button

to select the "Month".

Pressing



button sets the "Month" and moves the cursor to "Day".

Perform the same steps to set "Day", "Year", "Hour" and "Minute".

After setting "Minute", press MENU button ( ) to complete

the settings.

Press OFF button to return to standby mode.

1. If there are no operations for approximately 1 minute during the

setup mode, the setting will end automatically. If the settings end

while incomplete, start again from the beginning.

2. A maximum error of 60 seconds can occur in the displayed

time over a month. Periodically adjusting the time setting is

recommended.

3. When power is not supplied to the unit for a long time, the time

returns to its initial setting of "JAN/01/2009 00 : 00", and the menu

LED (red) will ﬂash as a notiﬁcation. Reset the time.

NOTES: Operations for setting numbers



button (press once): The date/time increases

by one.



button (press once): The date/time decreases

by one.



button (press once): The cursor moves to the

left.



button (pressed once): The cursor moves to

the right.



button (press and hold for 1 second or more.):

The date or time increases in succession.



button (press and hold for 1 second or more.

The date or time decreases in succession.

MENU button: Conﬁrm the setting.

The chime tone for the video door station can be selected from 4 sound

types. The initial setting is 1.

After performing step 1 in section 7-1, select "CALL TONE" and

press MENU button ( ).

In the "SELECT CALL TONE" screen, press



button or



button

to select the desired chime tone. The selected chime tone sounds,

enabling you to check the sound.

Press MENU button ( ) to complete the settings and return to

the "SETTING" screen.

Press REC button ( ) to cancel the

setting and return to the previous screen.

After performing steps 1 and 2 in section 7-1, select "LANGUAGE"

in the "INITIAL SETTING" screen and press

MENU button ( ).

In the SELECT THE LANGUAGE screen, press







, and



buttons to select the language.

Press MENU button

( )

to complete the settings and return to

the "INITIAL SETTING" screen.

7-2 SELECT THE LANGUAGE

7-4 SELECT CALL TONE

- 9 -

English Français Nederlands

7-5 EXTERNAL INPUT SETTING

When optional units operate (for example, when a sensor is activated or

call button is pressed), the master monitor station and sub master station

will receive an alert sound. Also, when notiﬁcation at door is enabled,

the door station also receives an alert sound.

These operations must be performed by an installer. Please do not

change these settings yourself.

7-6 Setting communication time

Select the door station communication time from "1 min.", "2 min.", "3

min.", and "5 min.". Communication time initial setting: "1 min."

After performing step 1 in section 7-1, select "COMMUNICATION"

and press

MENU button ( ).

In the "COMMUNICATION SETTING" screen, press



button or



button to select "COMM. TIME" and press

MENU button ( )

In the "COMMUNICATION TIME-OUT SETTING" screen, press



button or



button to select the communication time.

Press MENU button ( ) to complete the settings and return

to the previous screen. Press

REC button ( ) to cancel the

setting and return to the previous screen.

7-5-1

： Setting the optional units detection method.

Initial setting

After performing steps 1 and 2 in section 7-1, select "EXT. INPUT"

and press

MENU button ( ).

In the "EXTERNAL INPUT SETTING" screen, press



button and



button to select "DETECTION METHOD" and press

button (

In the "EXTERNAL INPUT DETECTION METHOD" screen, press



button or



button to select the detection method.

: dry closure contact input

: External input disabled

Press MENU button ( ) to complete the settings and return to

the previous screen.

7-5-2

： Setting the alert sound time.

Initial setting: Notiﬁcation at door disabled/alert sound

is 30 sec.

In the "EXTERNAL INPUT SETTING" screen, press



button or



button to select "NOTICE AT DOOR [1]" and press

button (

In the "NOTIFICATION AT DOOR SETTING" screen, press



button or



button to select the "Notiﬁcation method".

DISABLE 30SEC

: Notiﬁcation at door

disabled/alert sound is 30

sec.

DISABLE CONT.

: Notiﬁcation at door

disabled/alert sound is

continuous

ENABLE CONT.

: Notiﬁcation at door

enabled/alert sound is

continuous

Press MENU button ( ) to complete the settings and return

to the previous screen. Press

REC button ( ) to cancel the

setting and return to the previous screen.

- 10 -

EnglishFrançais

Nederlands

7-7 Automatic night volume adjustment

This automatically lowers the communication volume at the door station

only at night.Initial setting: "Disabled"

After performing step 1 in section 7-1, select "COMMUNICATION"

and press MENU button ( ).

In the "COMMUNICATION SETTING" screen, press



button or



button to select "NIGHT VOLUME" and press MENU button

( ).

In the "NIGHT TIME DOOR VOLUME CONTROL" screen, press



button or



button to select "ENABLE".

Press MENU button ( ) to complete the settings and return to

the previous screen.

Press REC button ( ) to cancel the setting and return to the

previous screen.

NOTES: Distinguishing between day and night is automatically done by the

door station.

7-8 Restore default setting

All settings can be restored to their condition at the time of purchase.

1. Recorded pictures are erased and settings are reset.

2. Pre-set functions (section 8-7) are not reset.

Settings reset with "RESTORE DEFAULT SETTING"

Setting name Available setting

Time JAN/01/2009 00 : 00

Language

ENG FRA ITA DUT SPA

Door station chime tone

(Tone 1)

(Tone 2)

(Tone 3)

(Tone 4)

Communication time 1 min. 2 min. 3 min. 5 min

Automatic night volume

adjustment

Enable Disable

External

input

Detection

N/O N/C Disable

Notiﬁcation

at door

OFF OFF ON

Sound time

30 sec. Continuous Continuous

Press-to-talk setting

Enable Disable

Recording

Pictures All sa ved pictures are erased.

Screen

Zoom x 3, Wide x 3

Wide x 3, Zoom x 3

Zoom x 6

Wide x 6

are initial vie ws

After performing steps 1 and 2 in section 7-1, select "INITIALIZE"

with





and press MENU button ( ).

In the "INITIALIZE" screen, press MENU button ( )

(approximately 1 sec.) to initialize. Press

REC button ( ) to

cancel initialization and return to the "MENU" screen.

4 LEDs light up during initialization. The screen goes out when

initialization is complete. (The menu LED ﬂashes)

- 11 -

English Français Nederlands

7-9 Press-to-talk setting

This disables the press-to-talk setting during communication with a door

station (section 8-1).

Initial setting: (press-to-talk enabled)

After performing step 1 in section 7-1, select "COMMUNICATION"

and press MENU button ( ).

In the "COMMUNICATION SETTING" screen, press



button or



button to select "ALLOW PTT" and press MENU button ( ).

In the "PTT SETTING" screen, press



button or



button to select

ON or OFF.

Press MENU button ( ) to complete the settings and return to

the "COMMUNICATION SETTING" screen.

7-10 Setting picture recording

During automatic recording, select the recording method for recording

pictures (up to 6 for each image) from the following four types. The

initial setting is for the ﬁrst three pictures to be zoom pictures at a pre-set

position, and for the next three pictures to be wide pictures.

Pictures are automatically recorded. First three

pictures are zoom pictures at a pre-set position,

and the next three pictures are wide pictures.

Pictures are automatically recorded. First three

pictures are wide pictures, and the next three

pictures are zoom pictures at a pre-set position.

Pictures are automatically recorded. All six

pictures are zoom pictures at a pre-set position.

Pictures are aut

omatically recorded. All six

pictures are wide pictures.

NOTES: The set picture recording method also applies to

images displayed during a call from the entrance.

The initial setting is for recording to be done with the ﬁrst three pictures

as zoom pictures at a pre-set position, and the next three pictures as wide

pictures.

After performing step 1 in section 7-1, select "PICTURE MEMORY"

and press

MENU button ( ).

In the "PICTURE MEMORY SETTING" screen, press



button or



button to select the recording method.

Press MENU button ( ) to complete the settings and return

to the "SETTING" screen. Press

REC button ( ) to cancel the

setting and return to the previous screen.

Zoom pictures (from 1st shot to 3rd shot) Wide pictures (from 4th shot to 6th shot)

1st shot

2nd shot

4th shot

5th shot

6th shot

3rd shot

- 12 -

EnglishFrançais

Nederlands

OPERATIONS

8-1 Answering a door call (HANDS-FREE mode, PTT mode)

Press CALL button.

Chime tone sounds, caller is seen on video monitor, and outside sound is

heard.

Audio and video turns off after approximately 45 seconds if not answered.

Press TALK button momentarily, and after the beep, communicate hands

free. Transmit LED (red) lights when you talk, and goes off as you listen to

caller (or hear outside sounds).

After ﬁnishing communication, pressing OFF button and communication

will end after the beep.

NOTES: 1. Communication (video) ends automatically

according to the set communication time. (Refer

to section 7-6)

2. The Transmit LED will light up and go out, but

this is not a malfunction.

1. The screen display will switch automatically according to the picture

recording settings (section 7-10).

2. Even if the screen display changes, ZOOM/WIDE button (section 8-5)

can be used to change the display.

3. When TALK button is pressed momentarily and communication starts,

the screen display will be held as is regardless of the picture recording

settings.

Instant voice call function

Even without answering, door area can be seen and heard with video and

audio (for approximately 45 seconds). Inside sound is not heard outside.

PTT mode

Press and hold TALK button for at least 1 second. A beep sounds,

and after approximately 1 second another beep sounds, which indicates

PTT mode is engaged. If

TALK button is pressed brieﬂy (less than 0.5

seconds), PTT mode will not be engaged.

When communicating, keep TALK button pressed. To hear the caller's

voice, release

TALK button.

After ﬁnishing communication, press OFF button and communication

will end after the beep.

NOTES: When press-to-talk is disabled, PTT mode cannot be

used.

8-2 Activating door release

Press DOOR RELEASE button.

Open door while the release mechanism is activated.

During release: The door release LED (red) lights.

- 13 -

English Français Nederlands

8-3 Entrance monitoring

Press MONITOR button in the standby mode.

The video monitor displays the image from the door station and the

incoming audio is heard.

If you do not press TALK button, the caller will not hear sounds

from the inside station.

Press OFF button to end communication.

NOTES: 1. To talk to the visitor during entrance monitoring, momentarily press

TALK button. This allows communication with the entrance.

2. The entrance monitoring turns off automatically after approximately

1 minute. To monitor the entrance again, repeat from the beginning.

3. During entrance monitoring, the entrance monitoring time can

be extended by approximately 1 min. by pressing

MONITOR

button again.

4. During entrance monitoring, the display uses a wide picture display.

If the

ZOOM/WIDE button

is pressed, the display changes to

the zoom picture.

5. At night, the Illuminator LED will not light up until

TALK

button is pressed.

6. If another inside unit attempts to perform entrance monitoring while

one inside unit is already doing so, a warning beeping sound will occur.

8-4 Room-to-room communication

Press CALL button to talk with the other person.

A call-in is sent to the sub master station.

The reply of the other person is not heard.

If the other person presses TALK button, hands free

communication is possible.

Press and release OFF button to end communication.

NOTES: 1. Room-to-room communication ends automatically after

approximately 10 minutes.

To perform room-to-room communication again, repeat from the

beginning.

2. If a call is received from the entrance during room-to-room

communication, the image from the entrance is displayed at the

monitor station and sub monitor station where communication

is taking place. Press

OFF button to end the room-to-

room communication, and press

TALK button to switch to

communication with the door station.

8-5 WIDE/ZOOM switching

Press ZOOM/WIDE button when a picture is displayed.

Switching between wide zoom occurs each time the b utton is pressed.

[Wide picture] [Zoom picture]

NOTES: 1. When the caller is not shown in the center of the picture, the zoom

picture can be moved up, down, left, and right. (Refer to section 8-6)

2. When the display changes from the wide picture to the zoom picture,

the zoom picture starts at the pre-set (section 8-7) position.

The wide picture may be distorted in comparison with the zoom

picture due to the characteristics of the door station camera, but this

is not a malfunction.

- 14 -

EnglishFrançais

Nederlands

8-6 Pan/tilt operation

When a zoom picture is displayed, press







, or



button.



: Up



: Do wn



: Left



: Right

Moving diagonally is also possible.

[Zoom picture]

The image range of the zoom picture and wide picture differs. The

edges of the wide picture do not display with the zoom picture.

8-7 Zoom Picture Pre-set

The picture can be set to display using a set zoom picture position

for when a call is received from the door station. When switching

from the wide picture to the zoom picture, the zoom picture displays

starting from the pre-set position.

When a zoom picture is displayed, press







, or



button.

(Ex. Pressing



button moves the picture up.)

While viewing the picture, s

et the desired picture position.

NOTES: 1. To change the zoom picture position that has been set, perform the

zoom position setting again. The previous setting will be overwritten.

2. The zoom picture position set with the master monitor station will

also be displayed at the sub monitor station.

Press ZOOM/WIDE button (for at least 2 seconds).

A beep will sound and the position setting will be completed.

8-8 Night illumination

At night, the door station Illuminator LED lights up during

calling or communication.

8-8-1

When a call is made from the door station

If CALL button of door station is pressed

When communication ends, the illuminator

LED will go out.

8-8-2

Light up the Illuminator LED during entrance

monitoring

When TALK button is pressed during entrance

monitoring, communication starts and the

Illuminator LED will light up.

Inside sound can be heard at the entrance.

Communication starts at this time, so be

aware that inside sound can be heard at

the entrance.

When communication ends, the illuminator LED will go out.

NOTES: Distinguishing between day and night is automatically

done by the door station.

The Illuminator

LED lights up.

- 15 -

English Français Nederlands

8-9 Backlight adjustment, Night sensitivity adjustment

To perform adjustment

Press ADJUST button when the image is difﬁcult to see.

Automatic adjustment to a more visible screen is performed. The

adjust icon displays at this time.

Adjust icon (day)

Adjust icon (night)

To cancel adjustment

Press ADJUST button during adjustment.

The adjust icon will disappear and the screen returns to the pre-

adjustment screen

NOTES: 1. Distinguishing between day and night is automatically done by

the door station.

2. Pressing ADJUST button at night makes the caller's face

easier to see, but moving subjects may be more difﬁcult to see.

[Before adjustment] [Before adjustment]

[After adjustment] [After adjustment]

Adjust icon

display

Adjust icon

display

8-10 Automatic recording

If a call is received from a video door station, the unit starts recording automatically. The record LED (red)

ﬂashes during recording.

Recording starts approximately 2 seconds after CALL button of video door station is pressed. A maximum

length of approximately 6 seconds (6 shots) can be recorded, with 1 picture and 1 shot for each second.

A maximum of 40 images can be recorded (combined total of automatic recording and manual recording images).

If 40 images are exceeded, images are overwritten starting from the image with the oldest recording date.

NOTES: 1. The automatic recording function cannot be cancelled.

2. The recorded pictures are recorded using the method (section 7-10) that has been set. However, if switching

between zoom and wide is performed during automatic recording, the displayed image will be recorded.

3. The picture during entrance monitoring is not automatically recorded. If you wish to record this screen, press

REC button.

The initial setting is for recording to be done with the ﬁrst three pictures as zoom pictures at a pre-set position, and the next three pictures as wide pictures.

8-11 Manual recording

Display a video image with an operation such as entrance

monitoring.

NOTES: 1. Manual recording is not possible during automatic recording (for

approximately 7 seconds after receiving a call from the door station).

2. After the end of automatic recording (approx. 7 seconds after

receiving a call from the door station), recording of another image in

addition to the automatically recorded image can be performed.

3. When manual recording, the displayed image is recorded.

Press REC button ( ). The record LED (red) ﬂashes (6 times)

and recording starts.

A maximum length of approximately 6 seconds (6 shots) can be

recorded, with 1 image and 1 shot for each second.

A maximum of 40 images can be recorded (combined total of

automatic recording and manual recording images). When 40

images are exceeded, new images overwrite old images starting

from the oldest recorded date.

Zoom pictures (from 1st shot to 3rd shot) Wide pictures (from 4th shot to 6t

h shot)

1st shot

2nd shot

4th picture

5th picture

6th picture

3rd shot

- 16 -

EnglishFrançais

Nederlands

8-12 Play recorded picture

If there are automatically recorded pictures, such as those taken while you were

out, the play LED (red) ﬂashes.

Press PLAY button in standby mode to display the picture with the most

recent date. *

displays on the screen when there are no recorded pictures.

07/16 JAN/01/2009 18:45

The operation status displays.

Sequence number of image currently being displayed/total recorded images

Displayed when image is unread.

Displays when image is saved.

[Play-waiting screen]

Time and date of

recording

Press PLAY button ( ) on the play-waiting screen. The recorded image

is played. When the play of one image ends, the next image is displayed.

07/16 JAN/01/2009 18:45

06/16 JAN/01/2009 17:45

[During play] [Next picture]

Display

during

play

To advance the play screen frame-by-frame, press PLAY button ( ) during

playback to pause. The play moves forward frame-by-frame each time

DOOR RELEASE button ( ) is pressed. When the frames of one image

end, the next picture is displayed.

Press OFF button to end.

* In the manual, screen icons and button icons are explained together.

* In addition, the operations shown below are also possible in the play

screen.

REC button ( ):

To display the previous (more recent date) picture. When the button is

pressed for 1 second or more, during the time that the button is pressed the

ﬁrst picture only of the dates can be checked in succession, from older to

more recent dates. (If

REC button is pressed while the picture with the

most recent date is displayed, the picture with the oldest date will display.)

DOOR RELEASE button ( ):

To display the next (older date) picture. When the button is pressed for 1

second or more, during the time that the button is pressed the ﬁrst picture only

of the dates can be checked in succession, in the direction of the older dates.

MENU button ( ):

To save or erase an image. (Refer to sections 8-13 and 8-14)

1. When there are multiple unread images, all images enter the "read"

condition even if only one image is played, and the play LED goes off.

2. The recorded pictures are displayed in order based on the date set

during recording.

* The operations shown below are possible during play.

MENU button (

)

The pictographic display on the screen can be erased.

PLAY button ( ):

To pause play.

DOOR RELEASE button ( ):

To display the picture with the next oldest date after fast forward playing.

In addition, the operations shown below are also possible during pause.

REC button ( ):

The play is reversed frame by frame each time the button is pressed. When the

frames of one image end, the unit returns to the play-waiting screen.

PLAY button ( ):

To return to the play screen.

MENU button ( ):

Pressing the button displays the picture with the next oldest date in the

play-waiting screen.

NOTES: 1. If there are no operations for at least approximately 1 minute, it will

end automatically.

2. If a call is received from a door station during play, the chime tone

sounds and the play is forcibly ended.

8-13 Save recorded picture

10 images can be saved from the recorded images (maximum of 40

images). Saved pictures are not overwritten.

Display the picture that you want to save in the play-waiting screen. (Refer to

section 8-12)

Press MENU button ( ) to display the save/erase selection screen.

JAN/01/2009 18:45

NOTES: 1. "CANNOT SAVE" is displayed if the number of possible saves is

exceeded. Cancel unnecessary saved image.

2. Images that have had the save canceled are not erased, but they are

overwritten if the number of recorded images is exceeded.

Press PLAY button ( ). If the image is saved, the key symbol is displayed.

If the image has already been saved, the save is canceled. Each time PLAY button

( ) is pressed, the operation switches between save and cancel.

JAN/01/2009 18:45

* In addition, the operations shown

below are also possible in the save/

erase selection screen.

MENU button ( ):

To erase the display picture.

(Refer to section 8-14)

REC button ( ):

To return to the play-waiting screen.

Warranty

Aiphone warrants thats its products have no material or workmanship defects under normal use conditions for two years after delivery to the end user. Aiphone will perform repair

or replacement free of charge if the product is defective and the warranty applies to the defect. Aiphone reserves unto itself the sole right to make the ﬁnal decision whether there is

a defect in materials and/or workman

ship and whether or not the product is under warranty. This warranty shall not apply to any Aiphone product which has been subject to misuse,

neglect, accident, or to use in violation of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover

batteries or damage caused by batteries used in connection with the unit. This

warranty only includes carry-in repairs. Any repairs must be made at the shop or place designated in

writing by Aiphone. Aiphone will not be responsible for any costs incurred during on-site service calls. Aiphone will not provide compensation for any loss or damage incurred by

the breakdown or malfunction of its products during use, or for any consequent inconvenience or losses that may result.

The object area of is the EU.

Garantie

Aiphone garantit que ce produit ne présente pas de défaut matériel ou de fabrication dans des conditions normales d'utilisation pendant les deux années suivant la livraison à

l'utilisateur ﬁnal. Aiphone en effectuera gratuitement la réparation ou le remplacement si le produit est défectueux et que la garantie s'applique pour le défaut. Aiphone se réserve

le droit exclusif de décider s’il existe ou non un défaut de matière ou de fabrication et si l’appareil est ou non couvert par la garantie. Cette garantie ne s’applique pas à tout

produit Aiphone qui a été l’objet d’une utilisation impropre, de négligence, d’un accident ou qui a été utilisé en dépit des instructions fournies; elle ne couvre pas non plus les

appareils qui ont été réparés ou modiﬁés en dehors de l’usine. Cette garantie ne couvre pas les piles ni les dégâts inﬂigés par les piles utilisées dans l’appareil. Cette garantie

comprend uniquement les réparations en atelier. Toutes les réparations doivent être réalisées à l'atelier ou au site désigné par écrit par Aiphone. Aiphone décline toute responsabilité

en cas de frais encourus pour les dépannages à domicile. Aiphone n’indemnisera pas le client en cas de pertes, de dommages ou de désagréments causés par une panne ou un

dysfonctionnement d’un de ses produits.

La zone d’application de est l’UE.

Garantie

Aiphone garandeert dat zijn producten onder normale gebruiksomstandigheden gedurende twee jaar na levering aan de eindgebruiker vrij zijn van materiaal- of fabricagefouten.

Aiphone zal het product kosteloos herstellen of vervangen als het defect is en de garantie van toepassing is op het defect. Aiphone behoudt zich het recht voor om als enige

deﬁnitief te bepalen of er al dan niet sprake is van

een materiaal- en/of fabricagefout; en of het product nog onder garantie is. Deze garantie geldt niet voor een Aiphone-product dat

is blootgesteld aan verkeerd gebruik, verwaarlozing, een ongeval of verkeerde bediening en evenmin voor toestellen die buiten de fabriek zijn hersteld of gewijzigd. Deze garantie

geldt niet voor batterijen of schade veroorzaakt door batterijen die in het toestel zijn g

ebruikt. Deze garantie geldt uitsluitend voor herstellingen die worden ingeleverd en opgehaald

door de klant. Alle herstellingen moeten worden uitgevoerd in de winkel of op de plaats die schriftelijk is aangeduid door Aiphone. Kosten die gepaard gaan met herstellingen ter

plaatse kunnen niet worden verhaald op Aiphone. Er kan geen schadeloosstelling van Aiphone worden geëist voor enig verlies of s

chade als gevolg van een defect of storing tijdens

het gebruik van zijn producten, of voor enig ongemak of verlies dat hieruit voortvloeit.

Het toepassingsgebied van is de EU.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and

used in accordance with the instruction

s, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures: R

eorient or relocate the receiving antenna Connect the equipment into an outlet on a circuit dif ferent

from that to which the receiver is connected. Increase the separation between the equipment and receiver. Consult the dealer or an e xperienced radio/TV technician for help.

English

Français

Nederlands

AIPHONE CO., LTD., NAGOYA, JAPAN

AIPHONE CORPORATION, BELLEVUE, WA, USA

AIPHONE S.A.S., LISSES-EVRY, FRANCE

Printed in Thailand

http://www.aiphone.com/