Linksys WRT54GS de handleiding

Merk: Linksys

Model: WRT54GS

Categorie: Routers

Type: de handleiding

Wireless

Model No.

Wireless

Quick Installation Guide

Model No.

WRT54GS (EU/LA)

Wireless-G

GHz

802.11g

Broadband Router

with SpeedBooster

Package Contents

• Wireless-G Broadband Router with SpeedBooster

• Setup CD-ROM with User Guide

• Power Adapter (may also include separate power

cord)

• Ethernet Network Cable

• Quick Installation (not supplied with all models)

A Turn off your network devices.

B Find a location for the Router. The

best place for the Router is usually

at the center of your wireless

network.

C Fix the direction of the antennas.

Normally, the higher you place the

antennas, the better the

performance will be.

D Connect a standard Ethernet

network cable to the Router’s

Internet port. Then connect the

other end of the network cable to

your broadband modem.

E Connect your computers or

Ethernet devices to the Router’s

numbered ports using standard

Ethernet network cabling.

F Power on the modem.

G Connect the power adapter to the

Router’s Power port and the other

end into an electrical outlet.

If you were supplied a power

adapter and separate power cord,

connect the power cord to the

power adapter, then connect the

power adapter to the Router’s

Power port. Plug the power cord

into an electrical outlet.

H Power on the PC you wish to use to

configure the Router.

Proceed to Step 2.

Connect the Router

There are two ways to configure the Router. Choose one of the following:

• Run the Setup CD-ROM - It is strongly recommended that you use the

Setup CD-ROM. Insert the Setup CD-ROM into the CD-ROM drive, and

follow the on-screen instructions.

• Use this Quick Installation guide - If you wish, you can use the Router’s Web-

based Utility. Proceed to Step 1 of this Quick Installation.

IMPORTANT: Make sure you use

the supplied power adapter. A

different power adapter could

damage the Router.

A Open your web browser. Enter

http://192.168.1.1 in its Address

field. Press the Enter key.

B A password request screen will

appear. Leave the User name

field blank, and enter the default

password, admin, in the

Password field. (For added

security, you should later set a

new password, using the

Administration tab’s

Management screen of the

Web-based Utility). Then click the

OK button.

C The Web-based Utility will

appear with the Setup tab

selected. If requested by your

Internet Service Provider (ISP),

complete the Host Name and

Domain Name fields. (These are

usually requested by cable ISPs.)

Otherwise, leave them blank.

Configure the Router

NOTE: Make sure your PC’s Ethernet

adapter is set to obtain an IP address

automatically. For more information,

refer to Windows Help.

D For the Internet Connection Type

setting, six connection types are

offered through the drop-down

menu, five of which are covered

here. Each Setup screen and

available features will differ

depending on which

connection type you select.

Internet Configuration Type

Automatic Configuration - DHCP: If

you are connecting through DHCP

or a dynamic IP address from your

ISP, keep this default setting.

Static IP: If your ISP assigns you a

static IP address, select Static IP

from the drop-down menu.

Complete the Internet IP Address,

Subnet Mask, Gateway, and Static

DNS fields. You need to enter at

least one DNS address.

PPPoE: If you are connecting

through PPPoE, select PPPoE from

the drop-down menu. Complete

the User Name and Password fields.

Select Keep Alive if you always want

to be connected to your ISP, or

select Connect on Demand if you

are charged for the time that you

are connected to your ISP.

PPTP: PPTP is a service used in

Europe only.

Complete the Internet IP Address,

Subnet Mask, and Gateway fields.

DHCP

Static IP

PPPoE

Complete the User Name and

Password fields.

Select Keep Alive if you always want

to be connected to your ISP, or

select Connect on Demand if you

are charged for the time that you

are connected to your ISP.

Telstra: Telstra is a service used in

Australia and New Zealand only. If

you are using an HBS connection,

check with your ISP for setup

information.

L2TP: L2TP is a service used in Isreal

only. If you are using an L2TP

connection, check with your ISP for

setup information.

E When you have finished

entering your Internet

connection settings, click the

Save Settings button to save

your changes.

F To configure the Router for your

wireless network, select the

Wireless Tab’s Basic Wireless

Settings screen.

G Select the Wireless Network

Mode:

Mixed: If your network has

Wireless-G and Wireless-B

devices, then keep the default

setting, Mixed.

G-Only: If your network only has

Wireless-G devices, select

G-Only.

PPTP

Telstra

L2TP

B-Only: If your network only has

Wireless-B devices, select

B-Only.

Disabled: If you want to disable

wireless networking, select

Disabled.

H Wireless Network Name (SSID).

The SSID is the network name

shared among all devices in a

wireless network. The SSID must

be identical for all devices in the

wireless network. It is case-

sensitive and must not have

more than 32 characters (use

any keyboard character). For

added security, you should

change the default SSID (linksys)

to a unique name.

I Wireless Channel. Select the

appropriate channel from the list

provided to correspond with

your network settings. All devices

in your wireless network must

broadcast on the same channel

in order to function correctly.

J Wireless SSID Broadcast. When

wireless clients survey the local

area for wireless networks to

associate with, they will detect

the SSID broadcast by the

Router. To broadcast the Router's

SSID, keep the default setting,

Enable. If you do not want to

broadcast the Router's SSID, then

select Disable.

K Change these settings as

described here and click the

Save Settings button to apply

your changes.

L Power your broadband modem

off and back on again.

M Restart or power on your PCs so

they can obtain the Router’s

new settings.To test the Router’s

settings, open your web browser

from any computer. In the

browser’s Address field, enter

www.linksys.com/registration

and press the Enter key.

Congratulations! The installation of

the Wireless-G Broadband Router

with SpeedBooster is complete.

If you need to set up wireless

security, proceed to the next

section.

IMPORTANT: Once the Router is

configured, wireless security,

WEP, WPA, or WPA2, should be

configured to prevent security

breaches in your network.

NOTE: If your wireless adapters

support Secure Easy Setup (SES), you

can use the SES button on the Router

to set them up.

To do this: Press the orange Cisco logo

on the Router’s front panel for at least

two seconds. Wait about 10 seconds.

When the logo turns white and begins

to flash, press the adapter’s

SecureEasySetup button. The Router’s

Cisco logo will stop flashing when the

device has been added to the

network. Repeat this procedure for

any additional SecureEasySetup

device.

Refer to the User Guide for further

instructions.

The Router comes equipped with six

types of Wireless Security: WPA

Personal, WPA Enterprise, WEP, WPA2

Personal, WPA2 Enterprise, and

Radius. These security methods are

not enabled right out of the box,

however. To configure wireless

security on the Router, do the

following:

A Open the Router’s Web Utility as

shown in Step 2, and click the

Wireless tab. The Basic Wireless

Settings screen will appear.

B Select Wireless Security to

configure wireless security on the

Router.

Directions for the configuration

of WEP, WPA Personal, and WPA2

Personal wireless security are

provided here.

C From the Security Mode pull-

down menu, select the type of

wireless security you’ll use on

your network.

WEP: WEP is a basic encryption

method, which is not as secure as

WPA. To use WEP, select a Default

Transmit Key (choose which Key to

use), and a level of WEP encryption,

64 bits 10 hex digits or 128 bits 26

hex digits. Then either generate a

WEP key using the Passphrase or

enter the WEP key manually.

Configuring Wireless Security

NOTE: If your wireless adapters

support Secure Easy Setup (SES), you

can use the SES button on the Router

to set up Wireless Security.

Basic Wireless Settings

NOTE: Please refer to the User Guide

if you wish to configure WPA

Enterprise, WPA2 Enterprise or

Radius wireless security options.

WEP Security Settings

WPA Personal: WPA gives you two

encryption methods, TKIP and AES,

with dynamic encryption keys.

Select the type of algorithm, TKIP or

AES. Enter a WPA Shared Key of 8-63

characters. Then enter a Group Key

Renewal period, which instructs the

Router how often it should change

the encryption keys.

WPA2 Personal: WPA2 supports, AES

or TKIP+AES, with dynamic

encryption keys. Select the type of

algorithm, AES or TKIP+AES. Enter a

WPA Shared Key of 8-63 characters.

Then enter a Group Key Renewal

period, which instructs the Router

how often it should change the

encryption keys.

D Click the Save Settings button.

Congratulations! Wireless Security is

now configured on the Router.

WRT54GSv7-EU-LA-QIG-70213NC BW

Linksys is a registered trademark or trademark of

Cisco Systems, Inc. and/or its affiliates in the U.S.

For additional information or troubleshooting

help, refer to the User Guide on the CD-ROM.

You can also e-mail for further support.

Website

http://www.linksys.com/international

Product Registration

http://www.linksys.com/registration

WPA Personal

Security Settings

WPA2 Personal

Wireless

Modell-Nr.

Wireless

Modell-Nr.

Kurzanleitung

WRT54GS (DE)

Wireless-G

GHz

802.11g

Lieferumfang

• Wireless-G Broadband-Router mit SpeedBooster

• Installations-CD-ROM mit Benutzerhandbuch

• Netzteil (Separates Netzkabel u. U. im Lieferumfang

enthalten)

• Ethernet-Netzwerkkabel

• Kurzanleitung (nicht bei allen Modellen enthalten)

Broadband-Router

mit SpeedBooster

A Schalten Sie die Netzwerkgeräte aus.

B Bestimmen Sie einen Standort für

den Router. Optimal ist in der Regel

eine zentrale Position des Routers im

Wireless-Netzwerk.

C Fixieren Sie die Ausrichtung der

Antennen. Je höher Sie die

Antennen anbringen, desto besser

ist in der Regel die Leistung.

D Schließen Sie ein Standard-Ethernet-

Netzwerkkabel am Internet-Port des

Routers an. Schließen Sie dann das

andere Ende des Netzwerkkabels an

das Breitband-Modem an.

E Schließen Sie die Computer oder

Ethernet-Geräte mit Standard-

Ethernet-Netzwerkkabeln an die

nummerierten Ports des Routers an.

F Schalten Sie das Modem ein.

G Schließen Sie das Netzteil an den

Stromanschluss des Routers an, und

stecken Sie das andere Ende in eine

Netzsteckdose.

Wenn im Lieferumfang ein Netzteil

und ein separates Netzkabel

enthalten sind, schließen Sie das

Netzkabel an das Netzteil an.

Schließen Sie dann das Netzteil

an den Power-Port des Routers an.

Stecken Sie das Netzkabel in eine

Steckdose.

H Schalten Sie dann den Computer

ein, mit dem Sie den Router

konfigurieren möchten.

Fahren Sie mit Schritt 2 fort.

Anschließen des Routers

Sie können den Router auf zwei Arten konfigurieren. Wählen Sie eine der

folgenden Methoden aus:

• Ausführen der Installations-CD-ROM – Es wird dringend empfohlen, die

Installations-CD-ROM zu verwenden. Legen Sie die Installations-CD-ROM in

das CD-ROM-Laufwerk ein, und befolgen Sie die Anweisungen auf dem

Bildschirm.

• Verwenden der Kurzanleitung – Sie können auch das integrierte

webbasierte Dienstprogramm des Routers verwenden. Beginnen Sie mit

Schritt 1 der Kurzanleitung.

WICHTIG: Verwenden Sie nur

das mitgelieferte Netzteil. Bei

Verwendung eines anderen

Netzteils könnte der Router

beschädigt werden.

A Öffnen Sie Ihren Web-Browser.

Geben Sie http://192.168.1.1 in

das Adressfeld ein. Drücken Sie

die Eingabetaste.

B Das Fenster zur Eingabe des

Kennworts wird angezeigt. Lassen

Sie das Feld Benutzername leer,

und geben Sie dann das

Standardpasswort admin in das

Feld Kennwort ein. (Um die

Sicherheit zu erhöhen, sollten Sie

später im webbasierten

Dienstprogramm auf der

Registerkarte Administration

(Verwaltung) im Fenster

Management

(Verwaltungsfunktionen) das

Kennwort ändern.) Klicken Sie

anschließend auf die

Schaltfläche OK.

C Das webbasierte Router-

Dienstprogramm wird mit

ausgewählter Registerkarte Setup

(Einrichtung) angezeigt. Wenn von

Ihrem ISP (Internet Service

Provider) Angaben in den Feldern

Host Name (Hostname) und

Domain Name (Domänenname)

gefordert werden, geben Sie die

relevanten Informationen in die

Felder ein. (Diese Daten sind in

der Regel für Kabel-ISPs

erforderlich.) Lassen Sie die Felder

anderenfalls leer.

Konfigurieren des Routers

HINWEIS: Stellen Sie sicher, dass der

Ethernet-Adapter Ihres PCs so

eingestellt ist, dass er automatisch

eine IP-Adresse bezieht. Weitere

Informationen hierzu finden Sie in der

Windows-Hilfe.

Im Dropdown-Menü stehen zur

Einstellung des Internet-

Verbindungstyps sechs

Verbindungstypen zur Verfügung,

fünf davon werden hier

behandelt. Die Einrichtungsfenster

und verfügbaren Funktionen

unterscheiden sich je nach

ausgewähltem Verbindungstyp.

Internet-Konfigurationstyp

Automatic Configuration – DHCP

(Automatische Konfiguration –

DHCP): Behalten Sie diese

Standardeinstellung bei, wenn Sie

Verbindungen über DHCP bzw. über

eine dynamische IP-Adresse Ihres ISPs

herstellen.

Static IP (Statische IP-Adresse): Wenn

Ihnen Ihr ISP eine statische IP-Adresse

zuweist, wählen Sie im Dropdown-

Menü die Option Static IP (Statische

IP-Adresse) aus. Füllen Sie die Felder

Internet IP Address (Internet-IP-

Adresse), Subnet Mask

(Subnetzmaske), Gateway, und

Static DNS (Statisches DNS) aus. Sie

müssen mindestens eine DNS-

Adresse eingeben.

PPPoE: Wenn Sie Verbindungen über

PPPoE herstellen, wählen Sie im

Dropdown-Menü die Option PPPoE

aus. Füllen Sie die Felder User Name

(Benutzername) und Password

(Passwort) aus.

Wählen Sie für eine ständige

Verbindung zu Ihrem ISP Keep Alive

(Verbindung aufrecht halten), oder

wählen Sie Connect on Demand

(Bei Bedarf verbinden), falls die

Verbindungszeit mit Ihrem ISP

gebührenpflichtig ist.

Static IP (Statische

IP-Adresse)

PPPoE

DHCP

PPTP: PPTP ist ein Dienst, der nur in

Europa verwendet wird.

Füllen Sie die Felder Internet IP

Address (Internet-IP-Adresse), Subnet

Mask (Subnetzmaske) und Gateway

aus.

Füllen Sie die Felder User Name

(Benutzername) und Password

(Passwort) aus.

Wählen Sie für eine ständige

Verbindung zu Ihrem ISP Keep Alive

(Verbindung aufrecht halten), oder

wählen Sie Connect on Demand

(Bei Bedarf verbinden), falls die

Verbindungszeit mit Ihrem ISP

gebührenpflichtig ist.

Telstra: Telstra ist ein Dienst, der nur

in Australien und Neuseeland

verwendet wird. Wenn Sie eine HBS-

Verbindung verwenden, klären Sie

die erforderlichen Setup-

Informationen mit Ihrem ISP ab.

L2TP: L2TP ist ein Dienst, der nur in

Israel verwendet wird. Wenn Sie eine

L2TP-Verbindung verwenden, klären

Sie die erforderlichen Setup-

Informationen mit Ihrem ISP ab.

E Wenn Sie alle Einstellungen zur

Internetverbindung

vorgenommen haben, klicken Sie

auf die Schaltfläche Save

Settings (Einstellungen speichern),

um die Änderungen zu

speichern.

F Um den Router für Ihr drahtloses

Netzwerk zu konfigurieren, wählen

Sie auf der Registerkarte Wireless

das Fenster Basic Wireless Settings

(Grundlegende Wireless-

Einstellungen) aus.

G Wählen Sie den Wireless-

Netzwerkmodus aus:

PPTP

Telstra

L2TP

Mixed (Gemischt): Behalten Sie

die Standardeinstellung Mixed

(Gemischt) bei, wenn Ihr Netzwerk

sowohl Wireless-G- als auch

Wireless-B-Geräte enthält.

G-Only (Nur G): Wenn

ausschließlich Wireless-G-Geräte

vorhanden sind, wählen Sie

G-Only (Nur G).

B-Only (Nur B): Wenn

ausschließlich Wireless-B-Geräte

vorhanden sind, wählen Sie

B-Only (Nur B).

Disabled (Deaktiviert): Um

das drahtlose Netzwerk zu

deaktivieren, wählen Sie Disabled

(Deaktiviert) aus.

H Wireless Network Name (SSID)

(Wireless-Netzwerkname (SSID)):

Bei der SSID handelt es sich um

den Netzwerknamen, der von

allen Geräten im drahtlosen

Netzwerk verwendet wird. Die SSID

muss für alle Geräte im Wireless-

Netzwerk identisch sein. Für die

maximal 32 Zeichen lange SSID

dürfen alle Zeichen der Tastatur

verwendet werden. Es wird

zwischen Groß- und

Kleinschreibung unterschieden.

Um die Sicherheit zu erhöhen,

sollten Sie die Standard-SSID

(linksys) in einen eindeutigen

Namen ändern.

I Wireless Channel (Wireless-

Kanal): Wählen Sie aus der Liste

den Ihren Netzwerkeinstellungen

entsprechenden Kanal aus.

Der einwandfreie Betrieb Ihres

Wireless-Netzwerks ist nur

gewährleistet, wenn die

Übertragung für alle Geräte

über denselben Kanal erfolgt.

J Wireless SSID Broadcast (Wireless-

SSID-Übertragung): Wenn Wireless-

Clients im lokalen Netzwerk nach

einer Verbindung zu Wireless-

Netzwerken suchen, erkennen sie

die Übertragung der SSID über

den Router. Zur Übertragung der

SSID des Routers behalten Sie die

Standardeinstellung Enable

(Aktivieren) bei. Wenn Sie die SSID

des Routers nicht übertragen

möchten, wählen Sie Disable

(Deaktivieren) aus.

K Ändern Sie die Einstellungen

wie hier beschrieben, und klicken

Sie auf die Schaltfläche Save

Settings (Einstellungen speichern),

um Ihre Änderungen

anzuwenden.

L Schalten Sie Ihr Breitbandmodem

aus und anschließend wieder ein.

M Starten Sie Ihre PCs neu, oder

schalten Sie sie wieder ein,

sodass die neuen Einstellungen

des Routers übernommen

werden können. Öffnen Sie Ihren

Web-Browser auf einem

beliebigen Computer, um die

Einstellungen des Routers zu

überprüfen. Geben Sie im

Adressfeld des Browsers

www.linksys.com/registration ein,

und drücken Sie die

Eingabetaste.

Gratulation! Die Installation des

Wireless-G Broadband-Routers mit

SpeedBooster ist hiermit

abgeschlossen.

Weitere Informationen zum Einstellen

der Wireless-Sicherheit erhalten Sie

im nächsten Abschnitt.

WICHTIG: Sobald der Router

konfiguriert ist, muss die

Wireless-Sicherheit (WEP, WPA

oder WPA2) konfiguriert werden,

sodass keine Sicherheitslücken

in Ihrem Netzwerk bestehen.

HINWEIS: Wenn Ihre Wireless-Adapter

SES (Secure Easy Setup) unterstützen,

können Sie die SES-Taste auf dem

Router verwenden, um sie einzurichten.

Vorgehensweise: Halten Sie das orange

leuchtende Cisco Logo auf der

Vorderseite des Routers mindestens

2 Sekunden lang gedrückt. Warten Sie

etwa 10 Sekunden. Sobald das Logo

weiß blinkt, drücken Sie die

SecureEasySetup-Taste am Adapter.

Das Cisco Logo des Routers leuchtet

konstant, sobald das Gerät zum

Netzwerk hinzugefügt wurde.

Wiederholen Sie diesen Vorgang für alle

weiteren SecureEasySetup-Geräte.

Weitere Anweisungen finden Sie im

Benutzerhandbuch.

Auf dem Router können sechs Wireless-

Sicherheitstypen eingerichtet werden:

WPA Personal, WPA Enterprise, WEP,

WPA2 Personal, WPA2 Enterprise und

Radius. Diese Sicherheitseinstellungen

sind jedoch nicht sofort nach Kauf

des Geräts aktiviert. Wenn Sie die

Wireless-Sicherheit auf dem Router

konfigurieren möchten, führen Sie

folgende Schritte aus:

A Öffnen Sie das webbasierte

Dienstprogramm des Routers wie

in Schritt 2 erklärt, und klicken Sie

auf die Registerkarte Wireless.

Das Fenster Basic Wireless Settings

(Grundlegende Wireless-

Einstellungen) wird angezeigt.

B Wählen Sie Wireless Security

(Wireless-Sicherheit), um die

Sicherheit des Routers im Wireless-

Netzwerkbetrieb zu konfigurieren.

Hier erhalten Sie Anweisungen

zum Konfigurieren der Wireless-

Sicherheitsoptionen WEP,

WPA Personal und

WPA2 Personal.

C Wählen Sie aus dem Pulldown-

Menü Security Mode

(Sicherheitsmodus) den Wireless-

Sicherheitstyp aus, den Sie in

Ihrem Netzwerk verwenden.

WEP: WEP ist eine einfache

Verschlüsselungsmethode, die nicht

so sicher wie WPA ist. Um WEP zu

verwenden, wählen Sie einen Wert

(bzw. den gewünschten Schlüssel) für

Default Transmit Key (Standard-

Übertragungsschlüssel) sowie die WEP-

Verschlüsselungsstufe aus – 64 bits

10 hex digits (64 Bit 10 Hexadezimal-

ziffern) oder 128 bits 26 hex digits

(128 Bit 26 Hexadezimalziffern).

Erstellen Sie anschließend einen

WEP Schlüssel, indem Sie entweder

Konfigurieren der Wireless-Sicherheit

HINWEIS: Wenn Ihre Wireless-Adapter

SES (Secure Easy Setup) unterstützen,

können Sie die SES-Taste auf dem

Router verwenden, um Wireless-

Sicherheit einzurichten.

HINWEIS: Lesen Sie im Benutzer-

handbuch nach, wenn Sie die

Wireless-Sicherheitsoptionen

WPA Enterprise, WPA2 Enterprise oder

Radius konfigurieren möchten.

Basic Wireless

Settings

(Grundlegende

Wireless-

Einstellungen)

Sicherheitseinstel-

lungen: WEP

die Passphrase verwenden oder den

WEP Schlüssel manuell eingeben.

WPA Personal: Bei WPA stehen Ihnen

zwei Verschlüsselungsmethoden (TKIP

und AES) mit dynamischen

Verschlüsselungsschlüsseln zur

Verfügung. Wählen Sie den

Algorithmus aus: TKIP oder AES.

Geben Sie einen gemeinsamen WPA-

Schlüssel mit einer Länge von 8 bis 63

Zeichen ein. Legen Sie anschließend

den Zeitraum für Group Key Renewal

(Erneuerung Gruppenschlüssel) fest.

Diese Zeitangabe teilt dem Router mit,

wie oft die Verschlüsselungsschlüssel

auszutauschen sind.

WPA2 Personal: WPA2 unterstützt AES

oder TKIP+AES mit dynamischen

Verschlüsselungsschlüsseln. Wählen

Sie den Algorithmus aus: AES oder

TKIP + AES. Geben Sie einen

gemeinsamen WPA-Schlüssel mit

einer Länge von 8 bis 63 Zeichen ein.

Legen Sie anschließend den Zeitraum

für Group Key Renewal (Erneuerung

Gruppenschlüssel) fest. Diese

Zeitangabe teilt dem Router mit,

wie oft die Verschlüsselungsschlüssel

auszutauschen sind.

D Klicken Sie auf die Schaltfläche

Save Settings (Einstellungen

speichern).

Gratulation! Wireless-Sicherheit ist

nun auf dem Router konfiguriert.

Linksys ist eine eingetragene Marke bzw. eine Marke von

Cisco Systems, Inc. und/oder deren Zweigunternehmen in

Weitere Informationen sowie Anleitungen

zur Fehlerbehebung finden Sie im

Benutzerhandbuch auf der CD-ROM. Sie

können auch per E-Mail weitere

Unterstützung anfordern.

Website

Deutschland

http://www.linksys.de

Österreich

http://www.linksys.at

Schweiz

http://www.linksys.com/international

Produktregistrierung

Deutschland

http://www.linksys.com/de/registrierung

Österreich

http://www.linksys.com/at/registrierung

Schweiz

http://www.linksys.com/ch/registrierung

WRT54GSv7-DE-QIG-70213NC BW

Sicherheits-

einstellungen:

WPA Personal

Sicherheits-

einstellungen:

WPA2 Personal

Wireless

Modelnr.

Wireless

Modelnr.

Installationsvejledning

WRT54GS (DA)

Wireless-G

GHz

802.11g

Pakkens indhold

• Trådløs G-bredbånds-router med SpeedBooster

• Installations-cd-rom med brugervejledning

• Strømforsyning (inkluderer evt. separat strømkabel)

• Ethernet-kabel

• Installationsvejledning (følger ikke med alle

modeller)

Bredbåndsrouter

med SpeedBooster

A Sluk for enhederne i dit netværk.

B Find en placering til routeren. Den

bedste placering til routeren er

normalt i centrum af dit trådløse

netværk.

C Fikser antennernes retning. Normalt

bliver modtage- og sendeforhold

bedre, jo højere du placerer

antennerne.

D Slut et standard-Ethernet-

netværkskabel til routerens

internetport. Slut derefter den

anden ende af netværkskablet til

dit bredbåndsmodem.

E Slut dine computere eller Ethernet-

enheder til routerens nummererede

porte ved hjælp af standard-

Ethernet-netværkskabler.

F Tænd for modemmet.

G Slut vekselstrømsforsyningen til

routerens strømstik og den anden

ende til en stikkontakt.

Hvis du har fået leveret

strømforsyningen og et separat

strømkabel, skal du tilslutte

strømkablet til strømforsyningen og

derefter tilslutte strømforyningen til

routerens strømstik. Slut strømkablet

til en stikkontakt.

H Tænd den pc, du vil bruge til

konfiguration af routeren.

Fortsæt til trin 2.

Tilslutning af routeren

Du kan konfigurere routeren på to måder. Vælg en af følgende:

• Kør installations-cd-rom'en – det anbefales på det kraftigste, at du bruger

installations-cd-rom'en. Placer installations-cd-rom'en i cd-rom-drevet, og

følg vejledningen på skærmen.

•Brug denne installationsvejledning – du kan eventuelt bruge routerens

webbaserede hjælpeprogram. Gå videre til trin 1 i

installationsvejledningen.

VIGTIGT: Sørg for at anvende den

leverede strømforsyning. Brug

af en anden strømforsyning kan

beskadige routeren.

A Åbn webbrowseren. Indtast

http://192.168.1.1 i feltet

Address (Adresse). Tryk på Enter.

B Der vises et skærmbillede til

indtastning af en adgangskode.

Lad feltet Brugernavn stå tomt, og

indtast standardadgangskoden

admin i feltet Adgangskode. Af

sikkerhedshensyn bør du senere

angive en ny adgangskode i

skærmbilledet Management

(Styring) under fanen

Administration i det webbaserede

hjælpeprogram. Klik herefter på

knappen OK.

C Det webbaserede

hjælpeprogram vises med fanen

Setup (Konfiguration) valgt. Hvis

din internetudbyder kræver det,

skal du udfylde felterne Host

Name (Værtsnavn) og Domain

Name (Domænenavn). Det

kræves normalt af

kabelinternetudbydere. I modsat

fald skal du bare lade dem stå

tomme.

Konfiguration af routeren

BEMÆRK: Sørg for, at pc'ens Ethernet-

netværkskort er indstillet, så det

automatisk henter en IP-adresse.

Yderligere oplysninger finder du i Windows

Hjælp.

D Der tilbydes seks forskellige typer

internetforbindelser i

rullemenuen. Fem af dem

nævnes her. Konfigurations-

skærmbillederne og de tilgæn-

gelige funktioner varierer,

afhængigt af hvilken forbindels-

estype du vælger.

Internetkonfigurationstype

Automatic Configuration - DHCP

(Automatisk konfiguration - DHCP):

Hvis du opretter forbindelse via

DHCP eller en dynamisk IP-adresse

fra din internetudbyder, skal du

beholde denne standardindstilling.

Static IP (Statisk IP): Hvis din

internetudbyder tildeler dig en statisk

IP-adresse, skal du vælge Static IP

(Statisk IP) i rullemenuen. Udfyld

felterne Internet IP Address (Internet-

IP-adresse), Subnet Mask

(Undernetmaske), Gateway og

Static DNS (Statisk DNS). Du skal

indtaste mindst én DNS-adresse.

PPPoE: Hvis du opretter forbindelse

via PPPoE, skal du vælge PPPoE i

rullemenuen. Udfyld felterne User

Name (Brugernavn) og Password

(Adgangskode).

Vælg Keep Alive (Permanent), hvis

du altid vil have forbindelse til din

internetudbyder, eller vælg

Connect on Demand (Opret

forbindelse efter behov), hvis du

betaler for den tid, du har

forbindelse til din internetudbyder.

PPTP: PPTP er en tjeneste, der kun

bruges i Europa.

Udfyld felterne Internet IP Address

(Internet-IP-adresse) Subnet Mask

(Undernetmaske), og Gateway.

Statisk IP

PPPoE

DHCP

Udfyld felterne User Name

(Brugernavn) og Password

(Adgangskode).

Vælg Keep Alive (Permanent), hvis

du altid vil have forbindelse til din

internetudbyder, eller vælg

Connect on Demand (Opret

forbindelse efter behov), hvis du

betaler for den tid, du har

forbindelse til din internetudbyder.

Telstra: Telstra er en tjeneste, der kun

bruges i Australien og New Zealand.

Hvis du bruger en HBS-forbindelse,

skal du henvende dig til din

internetudbyder for at få

konfigurationsoplysninger.

L2TP: L2TP er en tjeneste, der kun

bruges i Israel. Hvis du bruger en

L2TP-forbindelse, skal du henvende

dig til din internetudbyder for at få

konfigurationsoplysninger.

E Når du er færdig med at

indtaste indstillinger for din

internetforbindelse, skal du klikke

på knappen Save Settings

(Gem indstillinger) for at gemme

ændringerne.

F Vælg skærmbilledet Basic

Wireless Settings (Basisindstillinger

for trådløs) under fanen Wireless

(Trådløs) for at konfigurere

routeren til dit trådløse netværk.

G Vælg tilstanden for det trådløse

netværk:

Mixed (Blandet): Hvis du har

Trådløs-G- og Trådløs-B-enheder,

skal du beholde

standardindstillingen, Mixed.

G-Only (Kun G):Hvis du kun har

Trådløs-G-enheder, skal du

vælge G-Only.

PPTP

Telstra

L2TP

B-Only (Kun B): Hvis du kun har

Trådløs-B-enheder, skal du

vælge B-Only.

Disabled (Deaktiveret): Hvis du vil

deaktivere trådløst netværk, skal

du vælge Disabled.

H Wireless Network Name (SSID)

(Navn på trådløst netværk (SSID)).

SSID er det netværksnavn, der

deles af alle enhederne i et

trådløst netværk. SSID skal være

identisk for alle enheder i det

trådløse netværk. Der er forskel

på store og små bogstaver i

navnet, og det må ikke være

længere end 32 tegn (alle tegn

på tastaturet må bruges). Af

sikkerhedsmæssige årsager bør

du ændre standard-SSID (linksys)

til et entydigt navn.

I Wireless Channel (Trådløs

kanal). Vælg den relevante

kanal på den viste liste, så den

passer til dine

netværksindstillinger. Alle

enheder i dit trådløse netværk

skal sende på den samme

kanal for at fungere korrekt.

J Wireless SSID Broadcast (Trådløs

SSID-broadcast). Når trådløse

klienter overvåger lokalområdet

for at finde trådløse netværk, de

kan oprette forbindelse til,

registrerer de det SSID, der

udsendes af routeren. Behold

standardindstillingen Enable

(Aktiver) for at udsende routerens

SSID. Vælg Disable (Deaktiver),

hvis du ikke vil udsende

routerens SSID.

K Rediger disse indstillinger,

som beskrevet her, og klik

på knappen Save Settings

(Gem indstillinger) for at

anvende indstillingerne.

L Sluk og tænd for

bredbåndsmodemet igen.

M Genstart eller tænd for dine

pc'er, så de kan hente routerens

nye indstillinger. Hvis du vil teste

routerens indstillinger, kan du

åbne din webbrowser fra en

hvilken som helst computer.

Indtast www.linksys.com/

registration i feltet Address

(Adresse) i webbrowseren, og

tryk på Enter.

Tillykke! Installationen af Trådløs-G

Bredbåndsrouteren med

SpeedBooster er færdig.

Hvis du vil konfigurere trådløs

sikkerhed, skal du fortsætte til næste

afsnit.

VIGTIGT: Så snart routeren er

konfigureret, bør den trådløse

sikkerhed (enten WEP, WPA eller

WPA2) konfigureres for at undgå,

at der opstår åbninger i dit

netværk.

BEMÆRK: Hvis dine trådløse

netværkskort understøtter Secure Easy

Setup (SES) (Sikker Nem Konfiguration),

kan du bruge SES-knappen på routeren

til at konfigurere dem.

Hvis du vil gøre det, skal du trykke på

det orange Cisco-logo på routerens

frontpanel i mindst to sekunder. Vent i

cirka 10 sekunder. Tryk på knappen

SecureEasySetup

(SikkerNemKonfiguration) på

netværkskortet, når logoet bliver hvidt

og begynder at blinke. Routerens Cisco-

logo stopper med at blinke, når

enheden er blevet føjet til netværket.

Gentag denne fremgangsmåde for

eventuelle andre SecureEasySetup-

enheder (SikkerNemKonfiguration).

Se i brugervejledningen, hvis du ønsker

yderligere oplysninger.

Routeren leveres med seks typer

trådløs sikkerhed: WPA Personal, WPA

Enterprise, WEP, WPA2 Personal, WPA2

Enterprise og Radius. Disse

sikkerhedsmetoder aktiveres dog ikke,

hvis du ikke foretager dig noget. Hvis

du vil konfigurere trådløs sikkerhed på

routeren, skal du gøre følgende:

A Åbn routerens

webhjælpeprogram som vist

under trin 2, og klik på fanen

Wireless (Trådløs). Skærmbilledet

Basic Wireless Settings

(Basisindstillinger for trådløs)

vises.

B Vælg Wireless Security (Trådløs

sikkerhed) for at konfigurere

trådløs sikkerhed på routeren.

Her angives retningslinjer for

konfiguration af WEP, WPA

Personal og WPA2 Personal

trådløs sikkerhed.

C I rullemenuen Security Mode

(Sikkerhedstilstand) skal du

vælge den type trådløs

sikkerhed, du vil anvende på dit

netværk.

WEP: WEP er en grundlæggende

krypteringsmetode, der ikke er så

sikker som WPA. For at anvende

WEP skal du vælge en

transmissionsnøgle (vælg, hvilken

nøgle, du vil anvende) og et WEP-

krypteringsniveau: 64 bit 10 tegn i

hex eller 128 bit 26 tegn i hex.

Derefter skal du enten generere

en WEP-nøgle ved hjælp af dit

adgangsord eller angive WEP-

nøglen manuelt.

Konfiguration af trådløs sikkerhed

BEMÆRK: Hvis dine trådløse

netværkskort understøtter Secure Easy

Setup (SES) (Sikker Nem

Konfiguration), kan du bruge SES-

knappen på routeren til at konfigurere

Trådløs sikkerhed.

BEMÆRK: Hvis du ønsker at

konfigurere de trådløse

sikkerhedsmuligheder WPA Enterprise,

WPA2 Enterprise eller Radius, skal du

se i brugervejledningen.

Basic Wireless

Settings

(Basisindstillinger

for trådløs)

WEP Security

Settings

(WEP-sikkerheds-

indstillinger)

WPA Personal: Med WPA har du to

krypteringsmetoder med dynamiske

krypteringsnøgler: TKIP og AES. Vælg

algoritmetypen TKIP eller AES.

Indtast en WPA Shared Key på

8-63 tegn. Indtast derefter en

udskiftningsperiode for

gruppenøglerne, som angiver over

for routeren, hvor ofte den bør

ændre krypteringsnøglerne.

WPA2 Personal: WPA2 understøtter

AES eller TKIP+AES med dynamiske

krypteringsnøgler. Vælg

algoritmetypen AES eller TKIP+AES.

Indtast en WPA Shared Key på

8-63 tegn. Indtast derefter en

udskiftningsperiode for

gruppenøglerne, som angiver over

for routeren, hvor ofte den bør

ændre krypteringsnøglerne.

D Klik på knappen Save Settings

(Gem indstillinger).

Tillykke! Wireless Security

(Trådløs sikkerhed) er nu konfigureret

på routeren.

Linksys er et registreret varemærke tilhørende

Cisco Systems, Inc. og/eller Cisco Systems'

associerede selskaber i USA og visse andre

rettigheder forbeholdes.

Yderligere oplysninger eller hjælp til

fejlfinding finder du i brugervejledningen på

cd-rom'en. Du kan også sende en e-mail for

at få yderligere support.

Websted

http://www.linksys.com/international

Produktregistrering

http://www.linksys.com/registration

WRT54GSv7-DA-QIG-70213NC BW

WPA Personal Security

Settings

(Sikkerhedsindstillinger

for WPA-Personal)

WPA2 Personal Security

Settings (WPA2

Indstillinger for personlig

sikkerhed)

Nº de modelo

Inalámbrico

Nº de modelo

Guía de instalación rápida

WRT54GS (ES)

Wireless-G

GHz

802.11g

Contenido del paquete

• Router de banda ancha Wireless-G con SpeedBooster

• CD-ROM de configuración con guía del usuario

• Adaptador de corriente (es posible que se incluya

también un cable de alimentación por separado)

• Cable de red Ethernet

• Guía de instalación rápida (no se proporciona con

todos los modelos)

Router de banda ancha

con SpeedBooster

A Apague los dispositivos de red.

B Busque una ubicación para el

router. El mejor lugar para el router

suele ser el centro de la red

inalámbrica.

C Ajuste la dirección de las antenas.

Por lo general, el rendimiento es

mayor cuanto más altas estén

situadas las antenas.

D Conecte un cable de red Ethernet

estándar al puerto Internet del

router. A continuación, conecte el

otro extremo del cable de red al

módem de banda ancha.

E Conecte los ordenadores o

dispositivos Ethernet a los puertos

numerados del router mediante

cables de red Ethernet estándar.

F Encienda el módem.

G Conecte el adaptador de

corriente al puerto Power

(Alimentación) del router y el otro

extremo del cable a una toma de

corriente.

Si cuenta con un adaptador de

corriente y un cable de

alimentación, conecte el cable de

alimentación al adaptador de

corriente y, a continuación,

conecte el adaptador de corriente

al puerto Power (Alimentación) del

router. Conecte el cable a una

toma de corriente.

H Encienda el PC que desee utilizar

para configurar el router.

Vaya al paso 2.

Conexión del router

Puede configurar el router de dos formas. Seleccione una de las siguientes:

• Ejecute el CD-ROM de configuración. Se recomienda encarecidamente

que utilice dicho CD-ROM. Introduzca el CD-ROM de configuración en la

unidad de CD-ROM y siga las instrucciones que aparecen en la pantalla.

• Utilice esta guía de instalación rápida. Si lo desea, puede usar la utilidad

basada en Web del router. Vaya al paso 1 de esta guía de instalación

rápida.

IMPORTANTE: Asegúrese de que

utiliza el adaptador de

alimentación suministrado. Un

adaptador de corriente distinto

puede provocar daños al producto.

A Abra el explorador Web. Escriba

http://192.168.1.1 en el campo

Dirección. Pulse la tecla Intro.

B Aparece una pantalla en que

se le solicita una contraseña.

Deje en blanco el campo

Usuario e introduzca la

contraseña predeterminada,

admin, en el campo

Contraseña. (Para mayor

seguridad debe establecer una

nueva contraseña

posteriormente, mediante la

pantalla Management (Gestión)

de la ficha Administration

(Administración) de la utilidad

basada en Web.) Haga clic

en el botón Aceptar.

C Aparece la utilidad basada en

Web del router con la ficha

Setup (Configuración)

seleccionada. Si el proveedor

de servicios de Internet (ISP) lo

solicita, rellene los campos

Host Name (Nombre de host) y

Domain Name (Nombre de

dominio). (Los ISP por cable

suelen solicitar esta

información.) Si no, déjelos

en blanco.

Configuración del router

NOTA: Asegúrese de que el adaptador

Ethernet del PC está establecido para

obtener una dirección IP

automáticamente. Para obtener más

información, consulte la ayuda de

Windows.

D En el parámetro Internet

Connection Type (Tipo de

conexión a Internet) se ofrecen

seis tipos de conexión en el

menú desplegable, cinco de

los cuales se tratan aquí. Cada

pantalla Setup (Configuración) y

las funciones disponibles son

distintas según el tipo de

conexión que seleccione.

Internet Connection Type

(Tipo de conexión a Internet)

Automatic Configuration - DHCP

(Configuración automática - DHCP):

Si va a realizar la conexión

mediante DHCP o una dirección IP

dinámica del ISP, mantenga este

parámetro predeterminado.

Static IP (IP estática): Si el ISP le

asigna una dirección IP estática,

seleccione Static IP (IP estática) en

el menú desplegable. Rellene los

campos Internet IP Address

(Dirección IP de Internet), Subnet

Mask (Máscara de subred),

Gateway (Puerta de enlace) y Static

DNS (DNS estático). Debe introducir

por lo menos una dirección DNS.

PPPoE: Si realiza la conexión

mediante PPPoE, seleccione PPPoE

en el menú desplegable. Rellene

los campos User Name (Nombre

de usuario) y Password

(Contraseña).

Seleccione Keep Alive (Mantener

activo) si desea estar conectado

continuamente al ISP. De lo

contrario, seleccione Connect on

Demand (Conectar cuando se

solicite) si debe pagar según el

tiempo que esté conectado al ISP.

PPTP: PPTP es un servicio que sólo se

utiliza en Europa.

Rellene los campos Internet IP

Address (Dirección IP de Internet),

Subnet Mask (Máscara de subred) y

Gateway (Puerta de enlace).

Static IP

(IP estática)

PPPoE

DHCP

Rellene los campos User Name

(Nombre de usuario) y Password

(Contraseña).

Seleccione Keep Alive (Mantener

activo) si desea estar conectado

continuamente al ISP. De lo

contrario, seleccione Connect on

Demand (Conectar cuando se

solicite) si debe pagar según el

tiempo que esté conectado al ISP.

Telstra: Telstra es un servicio que

sólo se utiliza en Australia y Nueva

Zelanda. Si utiliza una conexión HBS,

consulte con el ISP para obtener la

información de configuración.

L2TP: L2TP es un servicio que sólo se

utiliza en Israel. Si utiliza una

conexión L2TP, consulte con el ISP

para obtener la información de

configuración.

E Cuando termine de introducir

los parámetros de conexión a

Internet, haga clic en el botón

Save Settings (Guardar

parámetros) para guardar los

cambios.

F Para configurar el router para la

red inalámbrica, seleccione la

pantalla Basic Wireless Settings

(Parámetros inalámbricos

básicos) de la ficha Wireless

(Inalámbrico).

G Seleccione el modo de red

inalámbrica:

Mixed (Mixto): Si cuenta con

dispositivos Wireless-G y

Wireless-B en la red, mantenga

el parámetro predeterminado,

Mixed (Mixto).

G-Only (Sólo G): Si sólo tiene

dispositivos Wireless-G,

seleccione G-Only (Sólo G).

PPTP

Telstra

L2TP

B-Only (Sólo B): Si sólo tiene

dispositivos Wireless-B,

seleccione B-Only (Sólo B)

Disable (Desactivar): Si desea

desactivar la red inalámbrica,

seleccione Disable (Desactivar).

H Wireless Network Name (SSID)

(Nombre de la red inalámbrica,

SSID). EL SSID es un nombre de

red que comparten todos los

dispositivos de una red

inalámbrica. Debe ser el mismo

para todos los dispositivos de la

red inalámbrica. El nombre

distingue entre mayúsculas y

minúsculas y no debe tener

más de 32 caracteres (puede

utilizar cualquier carácter del

teclado). Para mayor seguridad,

debe cambiar el SSID

predeterminado (linksys) por

otro.

I Wireless Channel (Canal

inalámbrico). Seleccione el

canal de la lista que coincida

con los parámetros de red. Para

que el funcionamiento sea

correcto, todos los dispositivos

de la red inalámbrica deben

emitir en el mismo canal.

J Wireless SSID Broadcast

(Difusión inalámbrica de SSID).

Cuando los clientes

inalámbricos sondeen el área

local en busca de redes

inalámbricas con las que

asociarse, detectarán el SSID

que difunde el router. Para

difundir el SSID del router,

mantenga el parámetro

predeterminado, Enable

(Activar). Si no desea difundir el

SSID del router, seleccione

Disable (Desactivar).

K Cambie estos parámetros

según lo descrito aquí y haga

clic en el botón Save Settings

(Guardar parámetros) para

aplicar los cambios.

L Apague el módem de banda

ancha y vuelva a encenderlo.

M Reinicie o encienda los PC para

que obtengan los nuevos

parámetros del router. Para

probar dichos parámetros, abra

el explorador Web en cualquier

ordenador. En el campo

Dirección del explorador,

escriba

www.linksys.com/registration

y pulse la tecla Intro.

Enhorabuena. La instalación del

router de banda ancha Wireless-G

con SpeedBooster ha finalizado.

Si necesita configurar la seguridad

inalámbrica, vaya a la

siguiente sección.

IMPORTANTE: Una vez

configurado el router se debe

configurar la seguridad

inalámbrica, ya sea WEP, WPA o

WPA2, para evitar que se vulnere

la seguridad de la red.

NOTA: Si los adaptadores inalámbricos

admiten SecureEasySetup (SES),

puede utilizar el botón SES del router

para configurarlos.

Para ello, pulse el logotipo naranja

de Cisco del panel frontal del router

durante un mínimo de dos segundos.

Espere unos 10 segundos. Cuando el

logotipo se vuelva blanco y empiece

a parpadear, pulse el botón

SecureEasySetup del adaptador.

El logotipo de Cisco del router dejará

de parpadear cuando el dispositivo se

haya agregado a la red. Repita este

procedimiento para cualquier

dispositivo SecureEasySetup

adicional.

Consulte la guía del usuario para

obtener más instrucciones.

El router incorpora seis tipos de

seguridad inalámbrica: WPA Personal,

WPA Enterprise, WEP, WPA2 Personal,

WPA2 Enterprise y Radius. Sin

embargo, estos métodos de

seguridad no están activados de

forma automática. Para configurar

la seguridad inalámbrica en el router,

siga estos pasos:

A Abra la utilidad Web del router

como se muestra en el paso 2 y

haga clic en la ficha Wireless

(Inalámbrico). Aparece la

pantalla Basic Wireless Settings

(Parámetros inalámbricos

básicos).

B Seleccione Wireless Security

(Seguridad inalámbrica) para

configurar la seguridad

inalámbrica en el router.

En este documento se

proporcionan instrucciones para

la configuración de la

seguridad inalámbrica WEP, WPA

Personal, y WPA2 Personal.

C En el menú desplegable

Security Mode (Modo de

seguridad), seleccione el tipo

de seguridad inalámbrica que

utilizará en la red.

WEP: Se trata de un método de

encriptación básico y no es tan

seguro como WPA. Para utilizar WEP,

seleccione una clave de

transmisión predeterminada

(Default Transmit Key; elija la que

desea utilizar) y un nivel de

encriptación WEP (WEP Encryption):

64 bits 10 hex digits (64 bits,

10 dígitos hexadecimales) o

128 bits 26 hex digits (128 bits,

26 dígitos hexadecimales).

A continuación, cree una clave

WEP mediante la frase de paso

(Passphrase) o introduzca

manualmente la clave WEP.

Configuración de la seguridad inalámbrica

NOTA: Si los adaptadores

inalámbricos admiten

SecureEasySetup (SES), puede utilizar

el botón SES del router para configurar

la seguridad inalámbrica.

NOTA: Consulte la guía del usuario

si desea configurar las opciones de

seguridad inalámbrica WPA

Enterprise, WPA2 Enterprise o

Radius.

Basic Wireless

Settings

(Parámetros

inalámbricos

básicos)

Parámetros de

seguridad WEP

WPA Personal: WPA ofrece dos

métodos de encriptación, TKIP y

AES, con claves de encriptación

dinámica. Seleccione el tipo de

algoritmo, TKIP o AES. Introduzca

una clave compartida WPA (WPA

Shared Key) que contenga entre 8 y

63 caracteres. A continuación,

introduzca un periodo de

renovación de clave de grupo

(Group Key Renewal), que indica al

router la frecuencia con que debe

cambiar las claves de

encriptación.

WPA2 Personal: WPA2 admite AES

o TKIP+AES con claves de

encriptación dinámica. Seleccione

el tipo de algoritmo, AES o

TKIP+AES. Introduzca una clave

compartida WPA (WPA Shared Key)

que contenga entre 8 y 63

caracteres. A continuación,

introduzca un periodo de

renovación de clave de grupo

(Group Key Renewal), que indica al

router la frecuencia con que debe

cambiar las claves de

encriptación.

D Haga clic en el botón Save

Settings (Guardar parámetros).

Enhorabuena. La seguridad

inalámbrica ya está configurada

en el router.

Linksys es una marca registrada o marca

comercial de Cisco Systems, Inc. o sus filiales en

Para obtener información adicional o ayuda

para la resolución de problemas, consulte

la guía del usuario proporcionada en el

CD-ROM. También puede solicitar asistencia

mediante el correo electrónico.

Sitio Web

http://www.linksys.com/international

Registro de productos

http://www.linksys.com/registration

WRT54GSv7-ES-QIG-70213NC BW

Parámetros de

seguridad WPA

Personal

Parámetros de

seguridad WPA2

Personal

Sans fil

Modèle

Sans fil

Modèle

Guide d'installation rapide

WRT54GS (FR)

Sans fil - G

GHz

802.11g

Contenu de l'emballage

• Routeur haut débit sans fil - G avec SpeedBooster

• CD-ROM d'installation contenant le Guide de

l'utilisateur

• Adaptateur électrique (peut également inclure un

cordon d'alimentation)

• Câble réseau Ethernet

• Installation rapide (livrée avec certains modèles

uniquement)

Routeur haut débit

avec SpeedBooster

A Mettez vos périphériques réseau

hors tension.

B Choisissez l'emplacement du

routeur. Le centre du réseau sans fil

est généralement le meilleur

emplacement.

C Réglez les antennes. En règle

générale, plus les antennes sont

hautes, meilleures sont les

performances.

D Branchez un câble réseau Ethernet

standard sur le port Internet du

routeur, puis branchez l'autre

extrémité du câble réseau sur votre

modem haut débit.

E A l'aide de câbles réseau Ethernet

standard, connectez vos

ordinateurs ou périphériques

Ethernet aux ports numérotés du

routeur.

F Mettez le modem sous tension.

G Branchez l'adaptateur secteur sur le

port d'alimentation du routeur et

branchez l'autre extrémité sur une

prise d'alimentation.

Si vous disposez d'un adaptateur

électrique et d'un cordon

d'alimentation, reliez ces deux

éléments, puis connectez

l'adaptateur au port d'alimentation

du routeur. Branchez le cordon

d'alimentation sur une prise

secteur.

H Allumez l'ordinateur que vous

voulez utiliser pour configurer le

routeur.

Passez à l'étape 2.

Connexion du routeur

Deux procédures permettent de configurer le routeur. Choisissez l'une des

deux méthodes suivantes :

• Exécutez le CD-ROM d'installation. Il est vivement recommandé de l'utiliser.

Insérez le CD-ROM d'installation dans le lecteur de CD-ROM et suivez les

instructions affichées à l'écran.

•Utilisez ce guide d'installation rapide. Si vous le souhaitez, vous pouvez

utiliser l'utilitaire Web du routeur. Passez à l'étape 1 de ce guide

d'installation rapide.

IMPORTANT : Veillez à utiliser

l'adaptateur électrique fourni.

L'utilisation d'un autre adaptateur

pourrait endommager le routeur.

A Ouvrez votre navigateur Web.

Saisissez http://192.168.1.1

dans le champ Adresse.

Appuyez sur la touche Entrée.

B Un écran vous invite à entrer un

mot de passe. Ne renseignez

pas le champ Nom d'utilisateur

et saisissez le mot de passe par

défaut, admin, dans le champ

Mot de passe. Pour optimiser la

sécurité, vous devrez définir

ultérieurement un nouveau mot

de passe par le biais de l'onglet

Administration de l'écran

Management (Gestion) de

l'utilitaire Web. Cliquez sur le

bouton OK.

C L'utilitaire Web apparaît et son

onglet Setup (Configuration) est

sélectionné. Si ces informations

sont requises par votre

fournisseur d'accès Internet (FAI),

renseignez les champs Host

Name (Nom d'hôte) et Domain

Name (Nom de domaine).

(Généralement, ces

informations sont demandées

par les fournisseurs d'accès via

le câble.) Dans le cas contraire,

laissez ces champs vides.

Configuration du routeur

REMARQUE : assurez-vous que

l'adaptateur Ethernet de votre

ordinateur est configuré pour obtenir

automatiquement une adresse IP.

Pour de plus amples informations,

reportez-vous à l'aide de Windows.

D Six types de connexion sont

proposés dans un menu

déroulant pour définir le

paramètre Internet Connection

Type (Type de connexion

Internet). Vous trouverez une

description de cinq de ces types

de connexion ci-après. Les

écrans d'installation et les options

disponibles varient selon le type

de connexion sélectionné.

Type de configuration Internet

Automatic Configuration - DHCP

(Configuration automatique -

DHCP) : si vous vous connectez à

Internet au moyen d'une adresse

DHCP ou IP dynamique fournie par

votre FAI, conservez ce paramètre

par défaut.

Static IP (adresse IP statique) : si

votre FAI vous attribue une adresse IP

statique, sélectionnez Static IP

(adresse IP statique). Renseignez les

champs Internet IP Address

(Adresse IP Internet), Subnet Mask

(Masque de sous-réseau), Gateway

(Modem routeur) et Static DNS (DNS

statique). Vous devez entrer au

moins une adresse DNS.

PPPoE : si vous vous connectez via le

protocole PPPoE, sélectionnez PPPoE

dans le menu déroulant. Remplissez

les champs User Name (Nom

d'utilisateur) et Password (Mot de

passe).

Choisissez l'option Keep Alive

(Maintenir la connexion) si vous

souhaitez être connecté en

permanence ou sélectionnez

Connect on Demand (Connexion à

la demande) si vous êtes facturé en

fonction de la durée de connexion à

votre FAI.

PPTP : ce service est utilisé en

Europe uniquement.

Complétez les champs Internet IP

Address (Adresse IP Internet), Subnet

Mask (Masque de sous-réseau) et

Gateway (Passerelle).

Adresse IP statique

PPPoE

DHCP

Renseignez les champs User Name

(Nom d'utilisateur) et Password (Mot

de passe).

Choisissez l'option Keep Alive

(Maintenir la connexion) pour rester

connecté en permanence à votre

fournisseur d'accès Internet (FAI) ou

Connect on Demand (Connexion à

la demande) si vous êtes facturé en

fonction de la durée de connexion

par votre FAI.

Telstra : Telstra est un service utilisé

en Australie et en Nouvelle-Zélande

uniquement. Si vous utilisez une

connexion HBS, demandez les

paramètres de configuration à

votre FAI.

L2TP : L2TP est un service utilisé en

Israël uniquement. Si vous utilisez

une connexion L2TP, demandez les

paramètres de configuration à

votre FAI.

E Une fois vos paramètres de

connexion Internet renseignés,

cliquez sur le bouton Save

Settings (Enregistrer les

paramètres) pour enregistrer vos

modifications.

F Pour configurer le routeur et

l'utiliser avec votre réseau sans

fil, sélectionnez l'écran Basic

Wireless Settings (Paramètres

sans fil de base) de l'onglet

Wireless (Sans fil).

G Sélectionnez le mode réseau

sans fil :

Mixed (Mixte) : si votre réseau

comporte des périphériques

sans fil G et B, conservez le

paramètre par défaut, Mixed

(Mixte).

G-only (G uniquement) : si votre

réseau ne comporte que des

périphériques sans fil G,

sélectionnez G-only

(G uniquement).

PPTP

Telstra

L2TP

B-only (B uniquement) : si votre

réseau ne comporte que des

périphériques sans fil B,

sélectionnez B-Only

(B uniquement).

Disabled (Désactiver) : si vous

souhaitez désactiver la mise en

réseau sans fil, sélectionnez

Disabled (Désactiver).

H Wireless Network Name (SSID)

(Nom du réseau sans fil [SSID]) : Il

s'agit du nom de réseau que

partagent tous les périphériques

interconnectés à un réseau sans

fil. Il doit être identique pour tous

les périphériques du réseau sans

fil. Ce paramètre sensible à la

casse ne doit pas comporter

plus de 32 caractères (tous les

caractères du clavier peuvent

être utilisés). Pour optimiser la

sécurité de votre système, vous

devez remplacer le nom du

réseau sans fil par défaut

(linksys) par un nom unique.

I Wireless Channel (Canal sans

fil) : Sélectionnez le canal

approprié dans la liste fournie en

fonction de vos paramètres

réseau. Tous les périphériques

de votre réseau sans fil doivent

communiquer sur le même

canal pour fonctionner

correctement.

J Wireless SSID Broadcast

(Diffusion SSID sans fil) : Lorsque

des ordinateurs clients sans fil

recherchent des réseaux sans fil

auxquels s'associer, ils détectent

le SSID diffusé par le routeur. Pour

diffuser le SSID du routeur,

conservez le paramètre par

défaut, Enable (Activer). Si vous

ne souhaitez pas diffuser le SSID

du routeur, sélectionnez Disable

(Désactiver).

K Modifiez ces paramètres

comme décrit ici et cliquez sur

le bouton Save Settings

(Enregistrer les paramètres) pour

appliquer vos modifications.

L Mettez votre modem haut débit

hors tension, puis de nouveau

sous tension.

M Redémarrez ou mettez vos

ordinateurs sous tension pour

qu'ils puissent charger les

nouveaux paramètres du

routeur. Testez les paramètres du

routeur en ouvrant un navigateur

Web à partir de n'importe quel

ordinateur. Dans le champ

Adresse du navigateur, saisissez

www.linksys.com/registration et

appuyez sur la touche Entrée.

Félicitations ! L'installation du routeur

haut débit sans fil G avec

SpeedBooster est terminée.

Si vous souhaitez configurer

la sécurité sans fil, passez

à la section suivante.

IMPORTANT : Une fois que le

routeur est configuré, il est

nécessaire de configurer la

sécurité sans fil WEP, WPA ou

WPA2 afin d'éviter les failles de

sécurité sur votre réseau.

REMARQUE : Si vos adaptateurs sans

fil sont compatibles avec la fonction

SecureEasySetup (SES), vous pouvez

utiliser le bouton SES du routeur pour

les configurer.

Pour ce faire, appuyez sur le logo

Cisco orange sur le panneau avant du

routeur pendant au moins deux

secondes. Patientez une dizaine de

secondes. Lorsque le logo devient

blanc et commence à clignoter,

appuyez sur le bouton

SecureEasySetup de l'adaptateur.

Le logo Cisco du routeur cesse de

clignoter lorsque le périphérique a été

ajouté au réseau. Répétez cette

procédure pour chaque périphérique

SecureEasySetup supplémentaire.

Reportez-vous au guide de l'utilisateur

pour obtenir des instructions

complémentaires.

Le routeur propose six types de

sécurité sans fil : WPA Personal

(WPA personnel), WPA Enterprise

(WPA entreprise), WEP, WPA2 Personal

(WPA2 personnel), WPA2 Enterprise

(WPA2 entreprise) et Radius. Ces

méthodes de sécurité ne sont

cependant pas activées par défaut.

Pour configurer la sécurité sans fil du

routeur, procédez comme suit :

A Ouvrez l'utilitaire Web du routeur

comme indiqué à l'étape 2 et

cliquez sur l'onglet Wireless (Sans

fil). L'écran Basic Wireless

Settings (Paramètres sans fil de

base) apparaît.

B Sélectionnez l'option Wireless

Security (Sécurité sans fil) pour

configurer la sécurité sans fil du

routeur.

Cette section comporte des

instructions de configuration de

la sécurité sans fil WEP,

WPA Personal (WPA personnel) et

WPA2 Personal

(WPA2 personnel).

C Sélectionnez le type de sécurité

sans fil que vous souhaitez utiliser

pour votre réseau dans le menu

déroulant Security Mode (Mode

de sécurité).

WEP : le système WEP est une

méthode de cryptage élémentaire

qui n'est pas aussi sûre que le

système WPA. Pour utiliser ce

système, sélectionnez une clé de

transmission par défaut en regard de

l'option appropriée Default Transmit

Key (Clé de transmission par défaut),

puis un niveau de cryptage WEP :

64 bits 10 hex digits (64 bits et

10 chiffres hexadécimaux) ou

128 bits 26 hex digits (128 bits et

26 chiffres hexadécimaux). Générez

ensuite une clé WEP à partir de

l'option Passphrase (Phrase de passe)

ou entrez-la manuellement.

Configuration de la sécurité sans fil

REMARQUE : Si vos adaptateurs sans

fil sont compatibles avec la fonction

SecureEasySetup (SES), vous pouvez

utiliser le bouton SES du routeur pour

configurer la sécurité sans fil.

REMARQUE : Reportez-vous au guide

de l'utilisateur si vous souhaitez

configurer les options de sécurité

sans fil WPA Enterprise

(WPA entreprise), WPA2 Enterprise

(WPA2 entreprise) et RADIUS.

Basic Wireless

Settings (Paramètres

sans fil de base)

WEP Security Settings

(Paramètres de

sécurité WEP)

WPA Personal (WPA personnel) : le

système WPA vous propose deux

méthodes de cryptage, TKIP et AES,

associées à des clés de cryptage

dynamiques. Sélectionnez le type

d'algorithme : TKIP ou AES. Entrez

une clé pré-partagée WPA

composée de 8 à 63 caractères.

Précisez ensuite un délai de

renouvellement des clés du groupe

dans la zone Group Key Renewal

(Renouvellement des clés du

groupe) pour indiquer au routeur à

quelle fréquence il doit changer les

clés de cryptage.

WPA2 Personal (WPA2 personnel) :

WPA2 prend en charge le

cryptage AES ou TKIP+AES avec des

clés de cryptage dynamique.

Sélectionnez le type d'algorithme,

AES ou TKIP+AES. Entrez une clé pré-

partagée WPA composée de 8 à

63 caractères. Précisez ensuite un

délai de renouvellement des clés du

groupe dans la zone Group Key

Renewal (Renouvellement des clés

du groupe) pour indiquer au routeur

à quelle fréquence il doit changer

les clés de cryptage.

D Cliquez sur le bouton Save

Settings (Enregistrer les

paramètres).

Félicitations ! La sécurité sans fil du

routeur est configurée.

Linksys est une marque déposée ou une marque

commerciale de Cisco Systems, Inc. et/ou de ses

filiales aux Etats-Unis et dans certains autres

droits réservés.

Pour obtenir de plus amples informations ou

une assistance technique, reportez-vous au

Guide de l'utilisateur figurant sur le CD-ROM

d'installation. Pour obtenir davantage d'aide,

vous pouvez également envoyer un e-mail.

Site Web

http://www.linksys.com/international

Enregistrement du produit

http://www.linksys.com/registration

WRT54GSv7-FR-QIG-70213NC BW

WPA Personal Security

Settings (Paramètres

de sécurité

WPA personnel)

WPA2 Personal Security

Settings (Paramètres de

sécurité

WPA2 personnel)

Wireless

N. modello

Wireless

N. modello

Guida di installazione rapida

WRT54GS (IT)

Wireless-G

GHz

802.11g

Contenuto della confezione

• Router a banda larga Wireless-G con SpeedBooster

• CD-ROM per l'installazione con Guida per l'utente

• Adattatore di corrente (può essere incluso un cavo di

alimentazione separato)

• Cavo di rete Ethernet

• Guida di installazione rapida (non fornita con tutti i

modelli)

Router a banda larga

con SpeedBooster

A Spegnere i dispositivi di rete.

B Individuare dove collocare il router.

In genere, la posizione migliore è al

centro della rete wireless.

C Orientare le antenne. Solitamente,

le prestazioni migliorano quanto

più in alto vengono installate le

antenne.

D Collegare un cavo di rete Ethernet

standard alla porta Internet del

router, quindi collegare l'altra

estremità del cavo di rete al

modem a banda larga.

E Collegare i computer o i dispositivi

Ethernet alle porte numerate del

router mediante cavi di rete

Ethernet standard.

F Accendere il modem.

G Collegare l'adattatore di corrente

alla porta di alimentazione del router

e l'altra estremità a una presa

elettrica.

Se vengono forniti un adattatore di

corrente e un cavo di alimentazione

separato, collegarli tra di loro, quindi

collegare l'adattatore alla porta di

alimentazione del router. Collegare il

cavo di alimentazione a una presa

elettrica.

H Accendere il computer da utilizzare

per configurare il router.

Passare alla fase 2.

Collegamento del router

È possibile configurare il router in due modi diversi. Scegliere una delle

modalità riportate di seguito.

• Eseguire il CD-ROM per l'installazione. Si raccomanda di utilizzare questo

CD-ROM. Inserire il CD-ROM per l'installazione nell'apposita unità e seguire

le istruzioni visualizzate sullo schermo.

• Seguire le istruzioni riportate in questa Guida di installazione rapida. Se lo si

desidera, è possibile utilizzare l'utilità del router basata sul Web. Continuare

con la fase 1 di questa Guida di installazione rapida.

IMPORTANTE Assicurarsi di

utilizzare l'adattatore di corrente

in dotazione. L'uso di un

adattatore di corrente differente

potrebbe causare danni al router.

A Aprire il browser Web. Immettere

http://192.168.1.1 nel campo

Indirizzo. Premere il tasto Invio.

B Viene visualizzata una

schermata in cui si chiede di

immettere la password. Lasciare

vuoto il campo Nome utente e

immettere la password

predefinita, admin, nel campo

Password. Per motivi di sicurezza,

si consiglia di impostare in

seguito una nuova password

nella scheda Administration

(Amministrazione) della

schermata Management

(Gestione) dell'utilità basata sul

Web. Fare clic sul pulsante OK.

C Viene visualizzata l'utilità basata

sul Web con la scheda Setup

(Configurazione) selezionata. Se

richiesto dal provider di servizi

Internet (ISP) in uso, completare i

campi Host Name (Nome host)

e Domain Name (Nome

dominio). Solitamente, questi

dati vengono richiesti dai

provider che forniscono

connettività via cavo. In caso

contrario, lasciare i campi vuoti.

Configurazione del router

NOTA Assicurarsi che l'adattatore

Ethernet del computer sia impostato in

modo da ottenere automaticamente un

indirizzo IP. Per ulteriori informazioni,

consultare la Guida in linea di Windows.

D Nel menu a discesa Internet

Connection Type (Tipo di

connessione Internet), sono

disponibili sei opzioni, cinque

delle quali sono descritte di

seguito. Le schermate di

configurazione e le relative

funzioni variano a seconda del

tipo di connessione selezionato.

Internet Connection Type (Tipo di

connessione Internet)

Automatic Configuration - DHCP

(Configurazione automatica -

DHCP): se si è collegati tramite

DHCP o un indirizzo IP dinamico

fornito dal provider di servizi Internet,

non modificare questa

impostazione predefinita.

Static IP (IP statico): se l'indirizzo IP

assegnato dal provider di servizi

Internet è statico, selezionare Static

IP (IP statico) dal menu a discesa.

Completare i campi Internet IP

Address (Indirizzo IP Internet), Subnet

Mask (Maschera di sottorete),

Gateway e Static DNS (DNS Statico).

È necessario specificare almeno un

indirizzo DNS.

PPPoE: se la connessione avviene

tramite PPPoE, selezionare PPPoE dal

menu a discesa. Completare i

campi User Name (Nome utente) e

Password.

Selezionare Keep Alive

(Connessione sempre attiva) se si

desidera essere sempre collegati al

provider di servizi Internet oppure

selezionare Connect on Demand

(Connessione su richiesta) se la

tariffa viene conteggiata in base al

tempo effettivo di connessione al

provider.

PPTP: è un servizio utilizzato

esclusivamente in Europa.

Completare i campi Internet IP

Address (Indirizzo IP Internet), Subnet

Mask (Maschera di sottorete) e

Gateway.

IP statico

PPPoE

DHCP

Completare i campi User Name

(Nome utente) e Password.

Selezionare Keep Alive

(Connessione sempre attiva) se si

desidera essere sempre collegati al

provider di servizi Internet oppure

selezionare Connect on Demand

(Connessione su richiesta) se la

tariffa viene conteggiata in base al

tempo effettivo di connessione al

provider.

Telstra: Telstra è un servizio utilizzato

solo in Australia e Nuova Zelanda.

Se si utilizza una connessione HBS,

contattare il provider di servizi

Internet per ottenere le informazioni

di configurazione.

L2TP: L2TP è un servizio utilizzato

esclusivamente in Israele. Se si

utilizza una connessione L2TP,

contattare il provider di servizi

Internet per ottenere le informazioni

di configurazione.

E Una volta terminata

l'impostazione dei parametri

della connessione a Internet,

fare clic sul pulsante Save

Settings (Salva impostazioni) per

salvare le modifiche apportate.

F Per configurare il router per la

rete wireless, selezionare la

schermata Basic Wireless

Settings (Impostazioni wireless di

base) nella scheda Wireless.

G Selezionare la modalità di rete

wireless desiderata:

Mixed (Mista): se sono collegati in

rete dispositivi Wireless-G e

Wireless-B, lasciare l'impostazione

predefinita Mixed (Mista).

G-Only (Solo G): se sono collegati

in rete solo dispositivi Wireless-G,

selezionare G-Only (Solo G).

PPTP

Telstra

L2TP

B-Only (Solo B): se sono collegati

in rete solo dispositivi Wireless-B,

selezionare B-Only (Solo B).

Disabled (Disattivata): se si

desidera disattivare la

connessione di rete wireless,

selezionare Disabled

(Disattivata).

H Wireless Network Name (SSID)

(Nome di rete wireless - SSID). SSID

è il nome della rete condiviso da

tutti i dispositivi presenti in una rete

wireless, che deve essere identico

per tutti i dispositivi collegati in

rete. È sensibile alla distinzione tra

maiuscole e minuscole e non

può contenere più di 32 caratteri

(che possono essere scelti tra tutti

quelli disponibili sulla tastiera). Per

una maggiore sicurezza, si

consiglia di sostituire il valore SSID

predefinito (linksys) con un nome

univoco.

I Wireless Channel (Canale

wireless). Nell'elenco fornito,

selezionare il canale

appropriato corrispondente alle

impostazioni di rete. Tutti i

dispositivi collegati alla rete

wireless devono comunicare

sullo stesso canale per poter

funzionare correttamente.

J Wireless SSID Broadcast

(Trasmissione SSID wireless).

Quando ricercano le reti wireless

a cui associarsi nell'area locale, i

client wireless rilevano

l'identificativo SSID trasmesso dal

router. Per trasmettere il valore

SSID del router, mantenere

l'impostazione predefinita

Enable (Attiva). Se non si

desidera trasmettere il valore

SSID del router, selezionare

Disable (Disattiva).

K Modificare le impostazioni

come indicato e fare clic sul

pulsante Save Settings (Salva

impostazioni) per applicare le

modifiche.

L Spegnere e riaccendere il

modem a banda larga.

M Riavviare o accendere i

computer in modo che

possano ricevere le nuove

impostazioni del router. Per

verificare le impostazioni del

router, aprire il browser Web da

uno dei computer. Nel campo

Indirizzo del browser, immettere

www.linksys.com/registration e

premere il tasto Invio.

Congratulazioni! L'installazione del

router a banda larga Wireless-G con

SpeedBooster è completata.

Per impostare la protezione

wireless, passare alla sezione

seguente.

IMPORTANTE Una volta

configurato il router, è necessario

configurare la protezione wireless,

WEP, WPA o WPA2, per impedire

violazioni della protezione in rete.

NOTA Se gli adattatori wireless

supportano Secure Easy Setup (SES), è

possibile utilizzare il pulsante SES del

router per configurarli.

Per eseguire questa operazione,

premere il logo Cisco arancione sul

pannello anteriore del router per

almeno due secondi. Attendere circa

10 secondi. Quando il logo diventa

bianco e inizia a lampeggiare, premere

il pulsante Secure Easy Setup

dell'adattatore. Quando il dispositivo è

stato aggiunto alla rete, il logo Cisco

del router smette di lampeggiare.

Ripetere questa procedura per ogni

dispositivo Secure Easy Setup

aggiuntivo.

Per ulteriori informazioni, consultare la

Guida per l'utente.

Il router è dotato di sei tipi di protezione

wireless: WPA Personal, WPA Enterprise,

WEP, WPA2 Personal, WPA2 Enterprise e

Radius. Questi metodi di protezione

non sono tuttavia pronti per l'immediato

utilizzo. Per configurare la protezione

wireless sul router, attenersi alla

seguente procedura:

A Aprire l'utilità del router basata sul

Web come mostrato nella

fase 2, quindi fare clic sulla

scheda Wireless. Viene

visualizzata la schermata Basic

Wireless Settings (Impostazioni

wireless di base).

B Selezionare Wireless Security

(Protezione wireless) per

configurare la protezione wireless

sul router.

Qui vengono fornite le istruzioni

per la configurazione della

protezione wireless WEP, WPA

Personal e WPA2 Personal.

C Nel menu a discesa Security

Mode (Modalità di protezione),

selezionare il tipo di protezione

wireless da utilizzare per la rete.

WEP: WEP è un metodo di cifratura di

base meno sicuro di WPA. Per

utilizzare WEP, selezionare una chiave

di trasmissione predefinita (scegliere

quale chiave usare) e un livello di

cifratura WEP, 64 bits 10 hex digits

(64 bit 10 cifre esadecimali) o 128

bits 26 hex digits (128 bit 26 cifre

esadecimali). Generare quindi una

chiave WEP utilizzando la passphrase

o immettere la chiave WEP

manualmente.

NOTA Se gli adattatori wireless

supportano Secure Easy Setup (SES),

è possibile utilizzare il pulsante SES

del router per impostare la protezione

wireless.

NOTA Per configurare le opzioni di

sicurezza WPA Enterprise, WPA2

Enterprise o Radius, consultare la

Guida per l'utente.

Basic Wireless

Settings

(Impostazioni

wireless di base)

Impostazioni di

protezione WEP

Configurazione della protezione

wireless

WPA Personal: WPA consente di

scegliere tra due metodi di

cifratura, TKIP e AES, che utilizzano

chiavi dinamiche. Selezionare il tipo

di algoritmo, TKIP o AES. Immettere

una chiave WPA condivisa di

lunghezza compresa tra 8 e

63 caratteri. Quindi, immettere un

intervallo di rinnovo della chiave di

gruppo per specificare la frequenza

con cui si desidera che il router

modifichi le chiavi di cifratura.

WPA2 Personal: WPA2 supporta AES

o TKIP+AES che utilizzano chiavi

dinamiche di cifratura. Selezionare il

tipo di algoritmo, AES o TKIP + AES.

Immettere una chiave WPA

condivisa di lunghezza compresa

tra 8 e 63 caratteri. Quindi,

immettere un intervallo di rinnovo

della chiave di gruppo per

specificare la frequenza con cui si

desidera che il router modifichi le

chiavi di cifratura.

D Fare clic su Save Settings (Salva

impostazioni).

Congratulazioni! La protezione

wireless è ora configurata sul router.

Linksys è un marchio o marchio registrato di

Cisco Systems, Inc. e/o delle relative aziende

affiliate negli Stati Uniti e in altri Paesi. Copyright

Per ulteriori informazioni o istruzioni relative

alla risoluzione dei problemi, consultare la

Guida per l'utente sul CD-ROM. È possibile

ricevere ulteriore assistenza anche inviando

un messaggio di posta elettronica.

Sito Web

http://www.linksys.com/international

Registrazione del prodotto

http://www.linksys.com/registration

WRT54GSv7-IT-QIG-70213NC BW

Impostazioni di

protezione WPA

Personal

Impostazioni di

protezione WPA2

Personal

Wireless

Modelnr.

Wireless

Modelnr.

Installatiehandleiding

WRT54GS (NL)

Wireless-G

GHz

802.11 g

Inhoud van de verpakking

• Wireless-G-breedbandrouter met SpeedBooster

• Installatie-cd-rom met gebruikershandleiding

• Netstroomadapter (mogelijk inclusief afzonderlijk

netsnoer)

• Ethernet-netwerkkabel

• Installatiehandleiding (wordt niet bij alle modellen

geleverd)

breedbandrouter

met SpeedBooster

A Schakel uw netwerkapparaten uit.

B Zoek een locatie waar u de router

wilt plaatsen. U kunt de router

doorgaans het best in het midden

van uw draadloze netwerk plaatsen.

C Bepaal de richting van de

antennes. Hoe hoger de antennes

worden geplaatst, hoe beter de

prestaties doorgaans zijn.

D Sluit een normale Ethernet-

netwerkkabel aan op de poort

Internet van de router. Sluit het

andere einde van de netwerkkabel

aan op uw breedbandmodem.

E Sluit uw computers of Ethernet-

apparaten aan op de

genummerde poorten van de

router en gebruik daarbij standaard

Ethernet-netwerkbekabeling.

F Schakel de modem in.

G Sluit de netstroomadapter aan op

de voedingspoort van de router en

het andere uiteinde op een

wandcontactdoos.

Als u een netstroomadapter met

een afzonderlijk netsnoer hebt, sluit

u het netsnoer aan op de

netstroomadapter. Sluit de

netstroomadapter vervolgens aan

op de voedingspoort van de router.

Sluit het netsnoer aan op een

wandcontactdoos.

H Schakel de pc in waarmee u de

router wilt configureren.

Ga verder met stap 2.

De router aansluiten

Er zijn twee manieren om de router te configureren. Kies een van de

volgende opties:

• Gebruik de installatie-cd-rom. Wij raden u ten zeerste aan de installatie-

cd-rom te gebruiken. Plaats de installatie-cd-rom in het cd-romstation en

volg de instructies op het scherm.

•Gebruik deze installatiehandleiding. Als u wilt, kunt u het webgebaseerde

hulpprogramma van de router gebruiken. Ga verder met stap 1 van deze

installatiehandleiding.

BELANGRIJK: Gebruik uitsluitend de

meegeleverde netstroomadapter.

Het gebruik van een andere

netstroomadapter kan de router

beschadigen.

A Open uw webbrowser. Typ

http://192.168.1.1 in het veld

Adres. Druk op de toets Enter.

B Er verschijnt nu een venster

waarin u uw wachtwoord kunt

invoeren. Laat het veld User

name (Gebruikersnaam) leeg

en voer het

standaardwachtwoord, admin,

in het veld Password

(Wachtwoord) in. (Voor extra

veiligheid moet u later een

nieuw wachtwoord opgeven via

het scherm Management

(Beheer) op het tabblad

Administration (Administratie)

van het webgebaseerde

hulpprogramma.) Klik

vervolgens op OK.

C Het webgebaseerde

hulpprogramma verschijnt,

waarin het tabblad Setup

(Instellingen) is geselecteerd.

Vul de velden Host Name

(Hostnaam) en Domain Name

(Domeinnaam) in als uw Internet

Service Provider (ISP) om deze

gegevens vraagt. (Dit wordt

meestal gevraagd door

kabelinternetproviders.) Anders

laat u deze velden leeg.

De router configureren

OPMERKING: Zorg ervoor dat de

Ethernet-adapter van uw pc automatisch

een IP-adres verkrijgt. Raadpleeg

Windows Help voor meer informatie.

D Voor de instelling Internet

Connection Type (Type

internetverbinding) worden zes

verbindingstypen in het

vervolgkeuzemenu aangeboden,

waarvan hier vijf zullen worden

besproken. Het venster Setup

(Instellingen) en de beschikbare

functies zijn bij elk geselecteerd

verbindingstype weer anders.

Internet Configuration Type

(Internetconfiguratietype)

Automatic Configuration - DHCP

(Automatische configuratie DHCP):

maakt u verbinding via DHCP of een

dynamisch IP-adres van uw ISP,

behoud deze standaardinstelling dan.

Static IP (Vast IP-adres): Selecteer

Static IP (Vast IP-adres) in het

vervolgkeuzemenu als uw ISP u een

vast IP-adres heeft gegeven. Vul de

velden Internet IP Address (IP-adres),

Subnet Mask (Subnetmasker),

Gateway (Gateway) en Static DNS

(Statische DNS) in. Vul ten minste

één DNS-adres in.

PPPoE: Als u verbinding maakt via

PPPoE, selecteert u PPPoE in het

vervolgkeuzemenu. Vul de velden

User Name (Gebruikersnaam) en

Password (Wachtwoord) in.

Selecteer Keep Alive (Continu

verbinding houden) als u altijd

verbonden wilt zijn met uw ISP of

selecteer Connect on Demand

(Verbinden op verzoek) als u betaalt

naar rato van de tijd dat u bent

verbonden met uw ISP.

PPTP: PPTP is een service die alleen

in Europa wordt gebruikt.

Vul de velden Internet IP Address

(IP-adres voor internet), Subnet Mask

(Subnetmasker) en Gateway in.

Vast IP-adres

PPPoE

DHCP

Vul de velden User Name

(Gebruikersnaam) en Password

(Wachtwoord) in.

Selecteer Keep Alive (Continu

verbinding houden) als u altijd

verbonden wilt zijn met uw ISP of

selecteer Connect on Demand

(Verbinden op verzoek) als u betaalt

naar rato van de tijd dat u bent

verbonden met uw ISP.

Telstra: Telstra wordt alleen in

Australië en Nieuw-Zeeland gebruikt.

Als u een HBS-verbinding gebruikt,

raadpleegt u uw ISP voor de juiste

instellingen.

L2TP: L2TP wordt alleen in Israël

gebruikt. Als u een L2TP-verbinding

gebruikt, raadpleegt u uw ISP voor

de juiste instellingen.

E Als u uw internetverbinding hebt

ingesteld, klikt u op de knop

Save Settings (Instellingen

opslaan) om de wijzigingen op

te slaan.

F Selecteer het venster Basic

Wireless Settings

(Standaardinstellingen WLAN) op

het tabblad Wireless (WLAN) om

de router te configureren voor

uw draadloze netwerk.

G Selecteer de Wireless Network

Mode (WLAN-netwerkmodus):

Mixed (Gemengd): Behoud de

standaardinstelling, Mixed

(Gemengd), als uw netwerk

Wireless-G- en Wireless-B-

apparaten heeft.

G-Only (Alleen G): Selecteer

G-Only (Alleen G) als uw netwerk

alleen Wireless-G-apparaten

heeft.

PPTP

Telstra

L2TP

B-Only (Alleen B): Selecteer

B-Only (Alleen B) als uw netwerk

alleen Wireless-B-apparaten

heeft.

Disabled (Uitgeschakeld):

Selecteer Disabled

(Uitgeschakeld) als u draadloze

netwerken wilt uitschakelen.

H Wireless Network Name (Naam

WLAN) (SSID). De SSID is de

netwerknaam die door alle

apparaten in een draadloos

netwerk wordt gedeeld. Deze

SSID moet voor alle apparaten

in het draadloze netwerk

hetzelfde zijn. De SSID is

hoofdlettergevoelig en mag niet

langer zijn dan 32 tekens (elk

teken op het toetsenbord mag

worden gebruikt). Voor extra

veiligheid is het raadzaam de

standaard-SSID (linksys) te

wijzigen in een unieke naam.

I Wireless Channel (Kanaal voor

draadloos netwerk). Selecteer in

de meegeleverde lijst het

kanaal dat overeenkomt met uw

netwerkinstellingen. Alle

apparaten in uw draadloze

netwerk moeten uitzenden via

hetzelfde kanaal om goed te

kunnen functioneren.

J Wireless SSID Broadcast (WLAN

SSID-broadcast). Als draadloze

clients in het lokale gebied

zoeken naar draadloze

netwerken waaraan ze zich

kunnen koppelen, detecteren

deze de SSID-broadcast van de

router. Gebruik de

standaardinstelling Enable

(Inschakelen) als u de SSID van

de router wilt verzenden. Als u

de SSID van de router niet wilt

verzenden, selecteert u Disable

(Uitschakelen).

K Wijzig de instellingen aan de

hand van de instructies en klik

op de knop Save Settings

(Instellingen opslaan) als u de

wijzigingen wilt toepassen.

L Schakel uw breedbandmodem

uit en weer in.

M Start uw pc's opnieuw of schakel

deze in, zodat de nieuwe

instellingen van de router van

kracht kunnen worden. Als u de

instellingen van de router wilt

testen, opent u de webbrowser

op een willekeurige computer.

Typ www.linksys.com/registration

in het veld Adres van uw browser

en druk op de toets Enter.

Gefeliciteerd! De installatie van de

Wireless-G-breedbandrouter met

SpeedBooster is voltooid.

Als u draadloze beveiliging wilt

installeren, gaat u verder met het

volgende gedeelte.

BELANGRIJK: Zodra de router is

geconfigureerd, moet de

draadloze beveiliging, WEP, WPA

of WPA2, worden geconfigureerd

om te voorkomen dat de veiligheid

van uw netwerk wordt aangetast.

OPMERKING: Als uw draadloze

adapters Secure Easy Setup (SES)

ondersteunen, kunt u de SES-knop op

de router gebruiken om deze te

installeren.

Druk hiervoor minimaal twee

seconden op het oranje Cisco-logo aan

de voorkant van de router. Wacht

ongeveer 10 seconden. Als het logo

wit wordt en begint te knipperen, drukt

u op de SecureEasySetup-knop van de

adapter. Nadat het apparaat aan het

netwerk is toegevoegd, houdt het

Cisco-logo op de router op met

knipperen. Herhaal deze procedure

voor elk SecureEasySetup-apparaat.

Raadpleeg de gebruikershandleiding

voor verdere instructies.

De router is uitgerust met zes typen

draadloze beveiliging: WPA Personal,

WPA Enterprise, WEP, WPA2 Personal,

WPA2 Enterprise, en Radius. Deze

beveiligingsmethoden zijn echter niet

standaard ingesteld. Doe het

volgende als u draadloze beveiliging

op de router wilt configureren:

A Open het webgebaseerde

hulpprogramma van de router

zoals beschreven in stap 2 en

klik op het tabblad Wireless

(WLAN). Het scherm Basic

Wireless Settings (Standaard-

instellingen WLAN) wordt nu

weergegeven.

B Selecteer Wireless Security

(Beveiliging draadloos netwerk) als

u draadloze beveiliging op de

router wilt configureren.

Aanwijzingen voor de configuratie

van WEP, WPA Personal en WPA2

Personal draadloze beveiliging

volgen hier.

C Selecteer in de vervolgkeuzelijst

Security Mode

(Beveiligingsmodus) het type

draadloze beveiliging dat u op

het netwerk wilt gebruiken.

WEP: WEP is een

standaardcoderingsmethode en

minder veilig dan WPA. Als u WEP wilt

gebruiken, selecteert u een

standaardzendsleutel (hiermee

bepaalt u welke sleutel wordt

gebruikt) en het niveau van de WEP-

codering: 64 bits 10 hex digits

(64-bits 10 hexadecimale tekens) of

128 bits 26 hex digits (128-bits

26 hexadecimale tekens). Genereer

vervolgens een WEP-sleutel met de

wachtzin of voer de WEP-sleutel

handmatig in.

OPMERKING: Als uw draadloze

adapters SecureEasySetup (SES)

ondersteunen, kunt u de SES-knop op

de router gebruiken om draadloze

beveiliging te verkrijgen.

OPMERKING: Raadpleeg de

gebruikershandleiding als u de opties

WPA Enterprise, WPA2 Enterprise of

Radius voor draadloze beveiliging

wilt configureren.

Standaard-

instellingen WLAN

Instellingen

WEP-beveiliging

Draadloze beveiliging

configureren

WPA Personal: WPA biedt twee

coderingsmethoden: TKIP en AES,

met dynamische coderingssleutels.

Selecteer het algoritme: TKIP of AES.

Voer een WPA-gedeelde sleutel van

8-63 tekens in. Geef vervolgens een

interval voor de vernieuwing van de

groepssleutel op. Hiermee bepaalt

u hoe vaak de router de

coderingssleutels moet wijzigen.

WPA2 Personal: WPA2 ondersteunt

AES of TKIP+AES, met dynamische

coderingssleutels. Selecteer het

type algoritme: AES of TKIP + AES.

Voer een WPA-gedeelde sleutel van

8-63 tekens in. Geef vervolgens een

interval voor de vernieuwing van de

groepssleutel op. Hiermee bepaalt

u hoe vaak de router de

coderingssleutels moet wijzigen.

D Klik op de knop Save Settings

(Instellingen opslaan).

Gefeliciteerd! De draadloze

beveiliging is nu op de router

geconfigureerd.

Linksys is een gedeponeerd handelsmerk van Cisco

Systems, Inc. en/of zijn dochterondernemingen in

Raadpleeg voor meer informatie of voor

probleemoplossing de gebruikershandleiding

op de cd-rom. U kunt ook per e-mail om

verdere ondersteuning vragen.

Website

http://www.linksys.com/international

Productregistratie

http://www.linksys.com/registration

WRT54GSv7-NL-QIG-70213NC BW

Instellingen WPA

Personal-beveiliging

Instellingen

WPA2 Personal-

beveiliging

Wireless

Modelo n.º

Wireless

Modelo n.º

Manual de Instalação Rápida

WRT54GS (PT)

Sem fios G

GHz

802.11g

Conteúdo da embalagem

• Router sem fios G de banda larga com SpeedBooster

• CD-ROM de configuração com Manual do Utilizador

• Transformador (pode incluir também um cabo de

alimentação separado)

• Cabo de rede Ethernet

• Instalação Rápida (não incluído com todos os

modelos)

Router de banda larga

com SpeedBooster

A Desligue os dispositivos de rede.

B Escolha um local para o Router.

Normalmente, o melhor local para

o Router é a parte central da rede

sem fios.

C Fixe a orientação das antenas.

Normalmente, quanto mais alto

colocar as antenas, melhor será o

desempenho.

D Ligue um cabo de rede Ethernet

padrão à porta de Internet do

Router. Em seguida, ligue a outra

extremidade do cabo de rede ao

modem de banda larga.

E Ligue os computadores ou os

dispositivos Ethernet às portas

numeradas do Router utilizando

cabos de rede Ethernet padrão.

F Ligue o modem.

G Ligue o transformador à porta de

alimentação do Router e a outra

extremidade a uma tomada

eléctrica.

Se lhe tiver sido fornecido um

transformador e um cabo de

alimentação separado, ligue o

cabo de alimentação ao

transformador e, em seguida,

ligue o transformador à porta de

alimentação do Router. Ligue o

cabo de alimentação a uma

tomada eléctrica.

H Ligue o computador que pretende

utilizar para configurar o Router.

Avance para o Passo 2.

Ligar o router

Existem dois modos de configurar o Router. Escolha um dos seguintes:

• Executar o CD-ROM de configuração - Recomenda-se vivamente a

utilização do CD-ROM de configuração. Coloque o CD-ROM de

configuração na unidade de CD-ROM e siga as instruções apresentadas

no ecrã.

• Utilizar este Manual de Instalação Rápida - Se pretender, poderá utilizar o

Utilitário baseado na Web do Router. Avance para o Passo 1 deste Manual

de Instalação Rápida.

IMPORTANTE: Certifique-se de

que utiliza o transformador

fornecido. A utilização de um

transformador diferente poderá

danificar o Router.

A Abra o Web browser. Introduza

http://192.168.1.1 no respectivo

campo Endereço. Prima a tecla

Enter.

B Será apresentado um ecrã a

solicitar a palavra-passe. Deixe

o campo Nome de utilizador

em branco e introduza a

palavra-passe predefinida,

admin, no campo Palavra-

passe. (Para obter segurança

adicional, deverá definir

posteriormente uma nova

palavra-passe, utilizando o ecrã

Management (Gestão) do

separador Administration

(Administração) do Utilitário

baseado na Web.) Em seguida,

clique no botão OK.

C O Utilitário baseado na Web

será apresentado com o

separador Setup (Configuração)

seleccionado. Se for solicitado

pelo fornecedor de serviços

Internet (ISP), preencha os

campos Host Name (Nome do

sistema anfitrião) e Domain

Name (Nome do domínio).

(Normalmente, os ISPs do

serviço de cabo requerem o

preenchimento destes

campos.) Caso contrário, deixe

os campos em branco.

Configurar o router

NOTA: Certifique-se de que a placa

Ethernet do computador está definida

para obter um endereço IP

automaticamente. Para obter mais

informações, consulte a Ajuda do

Windows.

D Para a definição Internet

Connection Type (Tipo de

ligação à Internet), são

fornecidos seis tipos de ligação

através do menu pendente,

cinco dos quais são abordados

aqui. Os ecrãs Setup

(Configuração) e as

funcionalidades disponíveis

variarão consoante o tipo de

ligação seleccionado.

Internet Connection Type

(Tipo de ligação à Internet)

Automatic Configuration - DHCP

(Configuração automática - DHCP):

Se estiver a ligar através de DHCP

ou de um endereço IP dinâmico do

ISP, mantenha esta predefinição.

Static IP (IP estático): Se o ISP atribuir

um endereço IP estático,

seleccione Static IP (IP estático) no

menu pendente. Preencha os

campos Internet IP Address

(Endereço IP de Internet), Subnet

Mask (Máscara de sub-rede),

Gateway, e Static DNS (DNS

estático). É necessário introduzir,

pelo menos, um endereço de DNS.

PPPoE: Se estiver a ligar através de

PPPoE, seleccione PPPoE no menu

pendente. Preencha os campos

User Name (Nome de utilizador) e

Password (Palavra-passe).

Seleccione Keep Alive (Manter

ligado) se pretender estar sempre

ligado ao ISP ou seleccione

Connect on Demand (Ligar

mediante pedido) se for cobrado

pelo tempo que está ligado ao ISP.

PPTP: PPTP é um serviço utilizado

apenas na Europa.

Static IP

(IP estático)

PPPoE

DHCP

Preencha os campos Internet IP

Address (Endereço IP de Internet),

Subnet Mask (Máscara de

sub-rede) e Gateway.

Preencha os campos User Name

(Nome de utilizador) e Password

(Palavra-passe).

Seleccione Keep Alive (Manter

ligado) se pretender estar sempre

ligado ao ISP ou seleccione

Connect on Demand (Ligar

mediante pedido) se for cobrado

pelo tempo que está ligado ao ISP.

Telstra: Telstra é um serviço utilizado

apenas na Austrália e na Nova

Zelândia. Se estiver a utilizar uma

ligação HBS, contacte o ISP para

obter as informações de

configuração.

L2TP: L2TP é um serviço utilizado

apenas em Israel. Se estiver a

utilizar uma ligação L2TP, contacte

o ISP para obter as informações de

configuração.

E Quando concluir a introdução

das definições de ligação à

Internet, clique no botão Save

Settings (Guardar definições)

para guardar as alterações.

F Para configurar o Router na rede

sem fios, seleccione o ecrã

Basic Wireless Settings

(Definições sem fios básicas) do

separador Wireless (Sem fios).

G Seleccione o Wireless Network

Mode (Modo de rede sem fios):

Mixed (Misto): Se existirem

dispositivos Sem fios G e Sem

fios B na rede, mantenha a

predefinição, Mixed (Misto).

PPTP

Telstra

L2TP

G-Only (Só G): Se apenas

existirem dispositivos Sem fios G

na rede, seleccione G-Only

(Só G).

B-Only (Só B): Se apenas

existirem dispositivos Sem fios B

na rede, seleccione B-Only

(Só B).

Disabled (Desactivado): Se

pretender desactivar a rede

sem fios, seleccione Disabled

(Desactivado).

H Wireless Network Name (SSID)

(Nome da rede sem fios (SSID)).

O SSID é o nome da rede

partilhado por todos os

dispositivos de uma rede sem

fios. O SSID tem de ser idêntico

para todos os dispositivos na

rede sem fios. É sensível a

maiúsculas e minúsculas e não

pode exceder 32 caracteres

(utilize qualquer carácter do

teclado). Para obter segurança

adicional, deverá alterar o SSID

predefinido (linksys) para um

nome exclusivo.

I Wireless Channel (Canal sem

fios). Seleccione o canal

adequado a partir da lista

fornecida, para corresponder às

definições da rede. Todos os

dispositivos da rede sem fios

têm de difundir no mesmo

canal para funcionarem

correctamente.

J Wireless SSID Broadcast

(Difusão de SSID sem fios).

Quando os clientes sem fios

pesquisarem a área local para

se associarem a redes sem fios,

detectarão a difusão do SSID

efectuada pelo Router. Para

difundir o SSID do Router,

mantenha a predefinição,

Enable (Activar). Se não

pretender difundir o SSID do

Router, seleccione Disable

(Desactivar).

K Altere as definições, conforme

aqui se descreve, e clique no

botão Save Settings (Guardar

definições) para aplicar as

alterações.

L Desligue e volte a ligar o

modem de banda larga.

M Reinicie ou ligue os

computadores, para obterem

as novas definições do Router.

Para testar as definições do

Router, abra o Web browser em

qualquer computador. No

campo Endereço do browser,

introduza

www.linksys.com/registration e

prima a tecla Enter.

Parabéns! A instalação do Router

sem fios G de banda larga com

SpeedBooster está concluída.

Se precisar de configurar a

segurança sem fios, avance para

a secção seguinte.

IMPORTANTE: Assim que o Router

estiver configurado, deve ser

configurada a segurança sem fios

(WEP, WPA ou WPA2) para evitar

falhas de segurança na rede.

NOTA: Se as suas placas sem fios

suportarem Secure Easy Setup (SES)

(Configuração fácil e segura), poderá

utilizar o botão SES do Router para as

configurar.

Para o fazer: Prima o logótipo

cor-de-laranja da Cisco no painel

frontal do Router durante, pelo menos,

2 segundos. Aguarde cerca de

10 segundos. Quando o logótipo ficar

branco e começar a piscar, prima o

botão SecureEasySetup da placa.

O logótipo da Cisco no Router deixará

de piscar quando o dispositivo for

adicionado à rede. Repita este

procedimento para quaisquer

dispositivos com SecureEasySetup

adicionais.

Consulte o Manual do Utilizador para

obter mais instruções.

O Router vem equipado com seis

tipos de segurança sem fios: WPA

Personal, WPA Enterprise, WEP, WPA2

Personal, WPA2 Enterprise e Radius.

No entanto, estes métodos de

segurança não vêm já activados.

Para configurar a segurança sem fios

no Router, efectue os seguintes

procedimentos:

A Abra o Utilitário baseado na

Web do Router, conforme é

mostrado no Passo 2, e clique

no separador Wireless (Sem

fios). Será apresentado o ecrã

Basic Wireless Settings

(Definições sem fios básicas).

B Seleccione Wireless Security

(Segurança sem fios) para

configurar a segurança sem

fios no Router.

As instruções para a

configuração da segurança

sem fios WEP, WPA Personal e

WPA2 Personal são fornecidas

aqui.

C No menu pendente Security

Mode (Modo de segurança),

seleccione o tipo de segurança

sem fios que irá utilizar na rede.

WEP: WEP é um método de

encriptação básico, que não é tão

seguro como o WPA. Para utilizar

WEP, seleccione a Default Transmit

Key (Chave de transmissão

predefinida) que pretende utilizar,

bem como o nível de encriptação

WEP, 64 bits 10 hex digits (64 bits,

10 dígitos hexadecimais) ou

128 bits 26 hex digits (128 bits,

26 dígitos hexadecimais). Em

seguida, proceda à geração de

uma chave WEP utilizando a

frase-passe ou introduza a chave

WEP manualmente.

Configurar a segurança sem fios

NOTA: Se as suas placas sem fios

suportarem Secure Easy Setup (SES)

(Configuração fácil e segura), poderá

utilizar o botão SES do Router para

configurar a segurança sem fios.

NOTA: Consulte o Manual do Utilizador

se pretender configurar as opções de

segurança sem fios WPA Enterprise,

WPA2 Enterprise ou Radius.

Basic Wireless

Settings

(Definições sem

fios básicas)

Definições de

segurança WEP

WPA Personal: O WPA oferece dois

métodos de encriptação, TKIP e

AES, com chaves de encriptação

dinâmicas. Seleccione o tipo de

algoritmo, TKIP ou AES. Introduza

uma WPA Shared Key (Chave

partilhada WPA) que tenha entre 8 e

63 caracteres. Em seguida,

introduza o período de Group Key

Renewal (Renovação do grupo de

chaves), que indica ao Router a

frequência com que deve alterar

as chaves de encriptação.

WPA2 Personal: O WPA2 suporta AES

ou TKIP+AES, com chaves de

encriptação dinâmicas. Seleccione

o tipo de algoritmo, AES ou

TKIP+AES. Introduza uma WPA

Shared Key (Chave partilhada WPA)

que tenha entre 8 e 63 caracteres.

Em seguida, introduza o período de

Group Key Renewal (Renovação do

grupo de chaves), que indica ao

Router a frequência com que deve

alterar as chaves de encriptação.

D Clique no botão Save Settings

(Guardar definições).

Parabéns! A segurança sem fios

está configurada no Router.

Linksys é uma marca registada ou marca

comercial da Cisco Systems, Inc. e/ou das

respectivas afiliadas nos E.U.A. e noutros países.

Para obter informações adicionais ou ajuda

para resolução de problemas, consulte o

Manual do Utilizador no CD-ROM. Também

poderá enviar uma mensagem de correio

electrónico para obter suporte.

Web site

http://www.linksys.com/international

Registo do produto

http://www.linksys.com/registration

WRT54GSv7-PT-QIG-70213NC BW

Definições de

segurança WPA

Personal

Definições de

segurança WPA2

Personal

Wireless

ModellnrModellnr

Snabbinstallationshandbok

WRT54GS (SV)

Wireless-G

GHz

802.11g

Innehåll i förpackningen

• Wireless-G Bredbandsrouter med SpeedBooster

• Installations-cd med användarhandbok

• Strömadapter (separat strömkabel kan medfölja)

• Ethernet-nätverkskabel

• Snabbinstallation (medföljer inte alla modeller)

Bredbandsrouter

med SpeedBooster

A Stäng av nätverksenheterna.

B Hitta en plats för routern. Den bästa

platsen är vanligtvis mitt i det

trådlösa nätverket.

C Rikta in antennerna. Ju högre upp

du placerar antennerna, desto

bättre blir täckningen.

D Anslut en vanlig Ethernet-

nätverkskabel till routerns Internet-

port. Anslut därefter den andra

änden av nätverkskabeln till

bredbandsmodemet.

E Anslut datorer och Ethernet-enheter

till routerns numrerade portar med

vanliga Ethernet-nätverkskablar.

F Starta modemet.

G Anslut strömadaptern till routerns

strömport och den andra änden till

ett eluttag.

Om en strömadapter och en

separat strömkabel medföljde

ansluter du först strömkabeln till

strömadaptern. Anslut sedan

strömadaptern till routerns

strömport. Anslut strömkabeln till ett

eluttag.

H Starta den dator du vill använda till

att konfigurera routern.

Gå vidare till steg 2.

Ansluta routern

Du kan konfigurera routern på två sätt. Välj något av följande alternativ:

• Kör installations-cd:n. Du rekommenderas att använda installations-cd:n.

Sätt in installations-cd:n i cd-enheten och följ anvisningarna på skärmen.

• Använd den här snabbinstallationshandboken. Om du vill kan du använda

routerns webbaserade verktyg. Fortsätt till steg 1 i den här

snabbinstallationen.

VIKTIGT! Se till att du använder

den medföljande strömadaptern.

En annan strömadapter kan

skada routern.

A Öppna webbläsaren. Ange

http://192.168.1.1 i fältet Adress.

Tryck på Enter.

B Ett fönster visas där du blir

ombedd att ange lösenord.

Lämna fältet Användarnamn

tomt och skriv sedan

standardlösenordet admin i

fältet Lösenord. (Senare bör du

av säkerhetsskäl skapa ett nytt

lösenord genom att gå till fliken

Administration i fönstret

Management (Hantering) i det

webbaserade verktyget.) Klicka

på OK.

C Det webbaserade verktyget

visas med fliken Setup

(Inställningar) markerad. Om

du blir ombedd av Internet-

leverantören fyller du i fälten

Host Name (Värdnamn) och

Domain Name (Domain Name).

(Detta efterfrågas oftast av

Internet-leverantörer.) Annars

lämnar du fälten tomma.

Konfigurera routern

OBS! Kontrollera att datorns Ethernet-

adapter är inställd på Hämta IP-

adress automatiskt. Mer information

finns i Windows-hjälpen.

D För inställningen av Internet-

anslutningstyp kan du välja

mellan sex olika anslutningstyper

i listrutan. Fem av dem beskrivs

här. Alla inställningsfönster och

tillgängliga funktioner skiljer sig åt

beroende på vilken

anslutningstyp du väljer.

Internet-anslutningstyp

Automatic Configuration - DHCP

(Automatisk konfiguration – DHCP):

Behåll standardinställningen om du

ansluter via DHCP eller en dynamisk

IP-adress från Internet-leverantören.

Static IP (Statisk IP-adress): Om

Internet-leverantören tillhandahåller

en statisk IP-adress väljer du Static IP

(Statisk IP) i listrutan. Fyll i fälten

Internet IP Address (Internet-IP-

adress), Subnet Mask (Nätmask),

Gateway och Static DNS (Statisk

DNS). Du måste ange minst en DNS-

adress.

PPPoE: Om du ansluter via PPPoE

väljer du PPPoE i listrutan. Fyll i fälten

User Name (Användarnamn) och

Password (Lösenord).

Välj Keep Alive (Behåll anslutning)

om du alltid vill vara ansluten till

Internet, eller välj Connect on

Demand (Anslut på begäran) om

du debiteras för den tid du är

ansluten till Internet.

PPTP: PPTP är en tjänst som endast

används i Europa.

Fyll i fälten Internet IP Address

(Internet-IP-adress), Subnet Mask

(Nätmask) och Gateway (Gateway).

Statisk IP

PPPoE

DHCP

Fyll i fälten User Name

(Användarnamn) och Password

(Lösenord).

Välj Keep Alive (Behåll anslutningen)

om du alltid vill vara ansluten till

Internet, eller välj Connect on

Demand (Anslut på begäran) om

du debiteras för den tid du är

ansluten till Internet.

Telstra: Telstra är en tjänst som

endast används i Australien och

Nya Zeeland. Om du använder en

HBS-anslutning kontaktar du Internet-

leverantören och ber om

inställningsinformation.

L2TP: L2TP är en tjänst som endast

används i Israel. Om du använder

en L2TP-anslutning kontaktar du

Internet-leverantören och ber om

inställningsinformation.

E När du är klar med

inställningarna för din Internet-

anslutning klickar du på Save

Settings (Spara inställningar) för

att spara alla ändringar.

F Om du vill konfigurera routern för

det trådlösa nätverket väljer du

fliken Wireless (Trådlöst) på

skärmen Basic Wireless Settings

(Grundläggande trådlösa

inställningar).

G Välj Wireless Network Mode

(Trådlöst nätverksläge):

Mixed (Blandat läge): Om

enheter av typen Wireless-G och

Wireless-B ingår i nätverket

behåller du standardinställningen

Mixed (Blandat läge).

G-Only (Endast G-läge): Om

endast enheter av typen

Wireless-G ingår i nätverket väljer

du G-Only (Endast G-läge).

PPTP

Telstra

L2TP

B-Only (Endast B-läge): Om

enheter av typen Wireless-B ingår

i nätverket väljer du B-Only

(Endast B-läge).

Disabled (Avaktiverad): Om du vill

avaktivera det trådlösa nätverket

väljer du Disabled (Avaktiverad).

H Wireless Network Name (SSID)

(Trådlöst nätverksnamn). SSID är

det nätverksnamn som delas av

alla enheter i ett trådlöst nätverk.

SSID:t måste vara identiskt för

alla enheter i det trådlösa

nätverket. Namnet är

skiftlägeskänsligt och får inte

överstiga 32 tecken (alla

tangentbordstecken kan

användas). Av säkerhetsskäl bör

du ändra standard-SSID:t

(linksys) till ett unikt namn.

I Wireless Channel (Trådlös

kanal). I listan väljer du en

lämplig kanal som motsvarar

dina nätverksinställningar. Alla

enheter i det trådlösa nätverket

måste sändas på samma kanal

för att fungera korrekt.

J Wireless SSID Broadcast (Trådlös

SSID-sändning): När trådlösa

klienter söker i det lokala nätet

efter trådlösa nätverk att ansluta

till kommer de att hitta SSID-

utsändningen från routern.

Om du vill sända routerns SSID

behåller du

standardinställningen Enable

(Aktivera). Om du inte vill sända

routerns SSID väljer du Disable

(Avaktivera).

K Ändra inställningarna enligt den

här beskrivningen och klicka på

Save Settings (Spara

inställningar) för att verkställa

ändringarna.

L Stäng av bredbandsmodemet

och sätt sedan på det igen.

M Starta om eller sätt på datorerna

så att routerns nya inställningar

börjar gälla. Om du vill testa

routerns inställningar startar du

webbläsaren på någon av

datorerna. I fältet Adress i

webbläsaren skriver du

www.linksys.com/registration

och trycker på Enter.

Klart! Installationen av Wireless-G

Bredbandsrouter med SpeedBooster

är klar.

Om du vill ställa in trådlös

säkerhet fortsätter du till nästa

avsnitt.

VIKTIGT! När routern är

konfigurerad bör trådlös säkerhet,

WEP, WPA eller WPA2, vara

konfigurerat för att förhindra

säkerhetsrisker på nätverket.

OBS! Om dina trådlösa adaptrar stöder

Secure Easy Setup (SES) kan du

använda knappen SES på routern för

att konfigurera dem.

Gör så här: Tryck på den

orangefärgade Cisco-logotypen på

routerns frontpanel i minst två

sekunder. Vänta i cirka 10 sekunder.

När logotypen blir vit och börjar blinka

trycker du på knappen

SecureEasySetup på adaptern.

Routerns Cisco-logotyp slutar blinka

när enheten har lagts till i nätverket.

Upprepa proceduren för övriga

SecureEasySetup-enheter.

Fler instruktioner finns i

användarhandboken.

Routern kommer utrustad med sex

typer av trådlös säkerhet: WPA

Personal (privat), WPA Enterprise

(företag), WEP, WPA2 Personal, WPA2

Enterprise och Radius. De här

säkerhetsmetoderna är dock inte

aktiverade direkt utan att du behöver

göra något. Konfigurera trådlös

säkerhet på routern genom att göra

följande:

A Öppna routerns webbverktyg på

det sätt som beskrivs i steg 2 och

klicka på fliken Wireless

(Trådlöst). Fönstret Basic Wireless

Settings (Grundläggande

trådlösa inställningar) visas.

B Välj Wireless Security (Trådlös

säkerhet) för konfigurering av

routerns trådlösa

säkerhetsinställningar.

Anvisningar för konfigurationen

av WEP, WPA Personal (WPA -

privat) och WPA2 Personal (WPA2

- privat) finns här.

C På menyn Security Mode

(Säkerhetsläge) väljer du den typ

av trådlös säkerhet du vill

använda på nätverket.

WEP: WEP är en enkel

krypteringsmetod som inte är lika

säker som WPA. Om du vill använda

WEP väljer du Default Transmit Key

(Standardöverföringsnyckel) (ange

vilken nyckel som ska användas)

och en nivå för WEP-krypteringen, 64

bits 10 hex digits (64-bitars, 10 hex-

siffror) eller 128 bits 26 hex digits

(128-bitars, 26 hex-siffror). Sedan

genererar du en WEP-nyckel med

ett lösenord eller anger WEP-nyckeln

manuellt.

Konfigurera trådlös säkerhet

OBS! Om dina trådlösa adaptrar

stöder Secure Easy Setup (SES) kan

du använda knappen SES på routern

för att konfigurera trådlös säkerhet.

OBS! Läs i användarhandboken om du

vill konfigurera alternativen WPA

Enterprise (WPA – företag), WPA2

Enterprise (WPA2 – företag) eller

Radius för trådlös säkerhet.

Grundläggande

trådlösa

inställningar

WEP-

säkerhetsinställningar

WPA Personal (WPA – privat): Med

WPA får du två krypteringsmetoder,

TKIP och AES, med dynamiska

krypteringsnycklar. Välj typ av

algoritm, TKIP eller AES. Ange en

WPA-delad nyckel på 8-63 tecken.

Slutligen anger du en

gruppnyckelförnyelseperiod, vilket

anger hur ofta krypteringsnycklarna

ska ändras för routern.

WPA2 Personal (WPA2 – privat):

WPA2 stödjer AES eller TKIP+AES

med dynamiska krypteringsnycklar.

Välj typ av algoritm, AES

eller TKIP+AES. Ange en WPA-

delad nyckel på 8-63 tecken.

Slutligen anger du en

gruppnyckelförnyelseperiod,

vilket anger hur ofta

krypteringsnycklarna ska

ändras för routern.

D Klicka på Save Settings

(Spara inställningar).

Klart! Trådlös säkerhet har nu

konfigurerats på routern.

Linksys är ett registrerat varumärke eller ett

varumärke som tillhör Cisco Systems, Inc. och/

eller dess samarbetspartner i USA och i vissa

Inc. Med ensamrätt.

Mer information samt felsökningshjälp finns i

användarhandboken på cd-skivan. Du kan

också skicka e-post till vår supportavdelning.

Webbplats

http://www.linksys.com/international

Produktregistrering

http://www.linksys.com/registration

WRT54GSv7-SV-QIG-70213NC BW

Säkerhetsinställningar

för WPA Personal

(WPA – privat).

Säkerhetsinställningar

för WPA2 Personal

(WPA2 – privat)

Model No.

Broadband Router

Wireless-G

WRT54GS (EU)

User Guide

WIRELESS

GHz

2.4

802.11g

with SpeedBooster

Wireless-G Broadband Router with SpeedBooster

Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco

rights reserved. Other brands and product names are trademarks or registered trademarks of their respective

holders.

How to Use This User Guide

This User Guide has been designed to make understanding networking with the Wireless-G Broadband Router

easier than ever. Look for the following items when reading this User Guide:

In addition to these symbols, there are definitions for technical terms that are presented like this:

Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like

this:

Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.

This exclamation point means there is a caution or

warning and is something that could damage your

property or the Wireless-G Broadband Router.

This checkmark means there is a note of interest and is

something you should pay special attention to while

using the Wireless-G Broadband Router.

This question mark provides you with a reminder about

something you might need to do while using the

Wireless-G Broadband Router.

word: definition.

Figure 0-1: Sample Figure Description

WRT54GSV7-EU-UG-70206NC BW

Wireless-G Broadband Router with SpeedBooster

Table of Contents

Chapter 1: Introduction 1

Welcome 1

What’s in this Guide? 2

Chapter 2: Planning Your Wireless Network 4

Network Topology 4

Ad-Hoc versus Infrastructure Mode 4

Network Layout 4

Chapter 3: Getting to Know the Wireless-G Broadband Router 6

The Back Panel 6

The Front Panel 7

Chapter 4: Connecting the Wireless-G Broadband Router 8

Overview 8

Hardware Installation for Connection to Your Broadband Modem 8

Hardware Installation for Connection of One Router to Another 10

Chapter 5: Configuring the Wireless-G Broadband Router 13

Overview 13

The Setup Tab - Basic Setup 14

The Setup Tab - DDNS 19

The Setup Tab - MAC Address Clone 20

The Setup Tab - Advanced Routing 21

The Wireless Tab - Basic Wireless Settings 22

The Wireless Tab - Wireless Security 23

The Wireless Tab - Wireless MAC Filter 26

The Wireless Tab - Advanced Wireless Settings 27

The Security Tab - Firewall 29

The Security Tab - VPN Passthrough 30

The Access Restrictions Tab - Internet Access 31

The Applications and Gaming Tab - Port Range Forward 33

The Applications & Gaming Tab - Port Triggering 34

The Applications and Gaming Tab - DMZ 35

The Applications and Gaming Tab - QoS 35

The Administration Tab - Management 37

Wireless-G Broadband Router with SpeedBooster

The Administration Tab - Log 37

The Administration Tab - Diagnostics 38

The Administration Tab - Factory Defaults 39

The Administration Tab - Firmware Upgrade 39

The Administration Tab - Config Management 40

The Status Tab - Router 41

The Status Tab - Local Network 42

The Status Tab - Wireless 43

Appendix A: Troubleshooting 44

Common Problems and Solutions 44

Frequently Asked Questions 53

Appendix B: Wireless Security 60

Security Precautions 60

Security Threats Facing Wireless Networks 60

Appendix C: Upgrading Firmware 63

Appendix D: Windows Help 64

Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter 65

Windows 98SE or Me Instructions 65

Windows 2000 or XP Instructions 65

For the Router’s Web-based Utility 66

Appendix F: Glossary 67

Appendix G: Specifications 72

Appendix H: Warranty Information 74

Appendix I: Regulatory Information 75

Appendix J: Contact Information 89

Wireless-G Broadband Router with SpeedBooster

List of Figures

Figure 3-1: The Router’s Back Panel 6

Figure 3-2: The Router’s Front Panel 7

Figure 4-1: Connecting Your Modem to the Router’s Internet Port 8

Figure 4-2: Connecting Your Network Devices 9

Figure 4-3: Connecting the Power 9

Figure 4-4: Connecting the Router Behind Another 10

Figure 4-5: Diagram for Connection to Another Router 10

Figure 4-6: Connect the Broadband Router’s Internet Port

to the other Router's Numbered Ethernet Port 11

Figure 4-7: Connecting Your Network Devices 11

Figure 4-8: Connecting the Power 12

Figure 5-1: Password Screen 13

Figure 5-2: Setup Tab - Basic Setup 14

Figure 5-3: DHCP Connection Type 14

Figure 5-4: Static IP Connection Type 14

Figure 5-5: PPPoE Connection Type 15

Figure 5-6: PPTP Connection Type 15

Figure 5-7: Telstra Cable Connection Type 16

Figure 5-8: L2TP Connection Type 16

Figure 5-9: Optional Settings 17

Figure 5-10: Router IP 17

Figure 5-11: Network Address Server Settings 17

Figure 5-12: Time Setting 18

Figure 5-13: Setup Tab - DDNS - DynDNS 19

Figure 5-14: Setup Tab - DDNS - TZO 19

Figure 5-15: Setup Tab - MAC Address Clone 20

Figure 5-16: Setup Tab - Advanced Routing (Gateway) 21

Figure 5-17: Setup Tab - Advanced Routing (Router) 21

Figure 5-18: Wireless Tab - Basic Wireless Settings 22

Figure 5-19: Wireless Tab - Wireless Security (WPA Personal) 23

Wireless-G Broadband Router with SpeedBooster

Figure 5-20: Wireless Tab - Wireless Security (WPA Enterprise) 23

Figure 5-21: Wireless Tab - Wireless Security (WPA2 Personal) 24

Figure 5-22: Wireless Tab - Wireless Security (WPA2 Enterprise) 24

Figure 5-23: Wireless Tab - Wireless Security (RADIUS) 25

Figure 5-24: Wireless Tab - Wireless Security (WEP) 25

Figure 5-25: Wireless Tab - Wireless MAC Filter 26

Figure 5-26: MAC Address Filter List 26

Figure 5-27: Wireless Tab - Advanced Wireless Settings 27

Figure 5-28: Security Tab - Firewall 29

Figure 5-29: Security Tab - VPN Passthrough 30

Figure 5-30: Access Restrictions Tab - Internet Access 31

Figure 5-31: Internet Policy Summary 31

Figure 5-32: List of PCs 31

Figure 5-33: Port Services 32

Figure 5-34: Applications and Gaming Tab - Port Range Forward 33

Figure 5-35: Applications and Gaming Tab - Port Triggering 34

Figure 5-36: Applications and Gaming Tab - DMZ 35

Figure 5-37: Applications and Gaming Tab - QOS 35

Figure 5-38: Administration Tab - Management 37

Figure 5-39: Administration Tab - Log 37

Figure 5-40: Administration Tab - Diagnostics 38

Figure 5-41: The Ping Test 38

Figure 5-42: The Traceroute Test 38

Figure 5-43: Administration Tab - Factory Defaults 39

Figure 5-44: Administration Tab - Firmware Upgrade 39

Figure 5-45: Administration Tab - Config Management 40

Figure 5-46: Status Tab - Router 41

Figure 5-47: Status Tab - Local Network 42

Figure 5-48: DHCP Clients Table 42

Figure 5-49: Status Tab - Wireless 43

Figure C-1: Upgrade Firmware 63

Figure E-1: IP Configuration Screen 65

Figure E-2: MAC Address/Adapter Address 65

Wireless-G Broadband Router with SpeedBooster

Figure E-3: MAC Address/Physical Address 65

Figure E-4: MAC Address Filter List 66

Figure E-5: MAC Address Clone 66

Chapter 1: Introduction

Welcome

Wireless-G Broadband Router with SpeedBooster

Chapter 1: Introduction

Welcome

Thank you for choosing the Linksys Wireless-G Broadband Router with SpeedBooster. The Wireless-G Broadband

Router with SpeedBooster will allow you to network wirelessly better than ever, sharing Internet access, files and

fun, easily and securely.

How does the Wireless-G Broadband Router with SpeedBooster do all of this? A router is a device that allows

access to an Internet connection over a network. With the Wireless-G Broadband Router with SpeedBooster, this

access can be shared over the four switched ports and via the wireless network, broadcast at either 11Mbps for

Wireless-B or 54Mbps for Wireless-G. In addition, WEP encryption provides greater security opportunities while

the whole network is protected through a Stateful Packet Inspection (SPI) firewall and NAT technology. All of

these security features, as well as full configurability, are accessed through the easy-to-use browser-based

utility.

But what does all of this mean?

Networks are useful tools for sharing computer resources. You can access one printer from different computers

and access data located on another computer's hard drive. Networks are even used for playing multiplayer video

games. So, networks are not only useful in homes and offices, they can also be fun.

PCs on a wired network create a Local Area Network. They are connected with Ethernet cables, which is why the

network is called “wired”.

PCs equipped with wireless cards or adapters can communicate without cumbersome cables. By sharing the

same wireless settings, within their transmission radius, they form a wireless network. The Wireless-G

Broadband Router with SpeedBooster bridges wireless networks of both 802.11b and 802.11g standards and

wired networks, allowing them to communicate with each other. And since this Router has SpeedBooster

technology, your wireless network performance increases by up to 30% from old 802.11g standards. In fact, even

non-SpeedBooster-equipped devices on your network will see a speed improvement when communicating with

SpeedBooster-enhanced equipment!

With your networks all connected, wired, wireless, and the Internet, you can now share files and Internet

access—and even play games. All the while, the Wireless-G Broadband Router with SpeedBooster protects your

networks from unauthorized and unwelcome users.

You should always use the Setup CD-ROM when you first install the Router. If you do not wish to run the Setup

Wizard on the Setup CD-ROM, then use the instructions in this Guide to help you connect the Wireless-G

Broadband Router with SpeedBooster, set it up, and configure it to bridge your different networks. These

instructions should be all you need to get the most out of the Wireless-G Broadband Router with SpeedBooster.

Chapter 1: Introduction

What’s in this Guide?

Wireless-G Broadband Router with SpeedBooster

What’s in this Guide?

This user guide covers the steps for setting up and using the Wireless-G Broadband Router with SpeedBooster.

• Chapter 1: Introduction

This chapter describes the Router’s applications and this User Guide.

• Chapter 2: Planning Your Wireless Network

This chapter describes the basics of wireless networking.

• Chapter 3: Getting to Know the Wireless-G Broadband Router

This chapter describes the Router’s physical features.

• Chapter 4: Connecting the Wireless-G Broadband Router

This chapter instructs you on how to connect the Router to your network.

• Chapter 5: Configuring the Wireless-G Broadband Router

This chapter explains how to use the Router’s Web-Based Utility.

• Appendix A: Troubleshooting

This appendix describes some problems and solutions, as well as frequently asked questions, regarding

installation and use of the Wireless-G Broadband Router.

• Appendix B: Wireless Security

This appendix explains the risks of wireless networking and some solutions to reduce the risks.

• Appendix C: Upgrading Firmware

This appendix instructs you on how to upgrade the Router’s firmware should you need to do so.

• Appendix D: Windows Help

This appendix describes how you can use Windows Help for instructions about networking, such as installing

the TCP/IP protocol.

• Appendix E: Finding the MAC Address and IP Address for your Ethernet Adapter.

This appendix describes how to find the MAC address for your computer’s Ethernet adapter so you can use

the Router’s MAC filtering and/or MAC address cloning feature.

• Appendix F: Glossary

This appendix gives a brief glossary of terms frequently used in networking.

• Appendix G: Specifications

This appendix provides the Router’s technical specifications.

Chapter 1: Introduction

What’s in this Guide?

Wireless-G Broadband Router with SpeedBooster

• Appendix H: Warranty Information

This appendix supplies the Router’s warranty information.

• Appendix I: Regulatory Information

This appendix supplies the Router’s regulatory information.

• Appendix J: Contact Information

This appendix provides contact information for a variety of Linksys resources, including Technical Support.

Chapter 2: Planning Your Wireless Network

Network Topology

Wireless-G Broadband Router with SpeedBooster

Chapter 2: Planning Your Wireless Network

Network Topology

A wireless local area network is exactly like a regular local area network (LAN), except that each computer in the

wireless network uses a wireless device to connect to the network. Computers in a wireless network share the

same frequency channel and SSID, which is an identification name shared by the wireless devices belonging to

the same wireless network.

Ad-Hoc versus Infrastructure Mode

Unlike wired networks, wireless networks have two different modes in which they may be set up: infrastructure

and ad-hoc. An infrastructure configuration is a wireless and wired network communicating to each other

through an access point. An ad-hoc configuration is wireless-equipped computers communicating directly with

each other. Choosing between these two modes depends on whether or not the wireless network needs to share

data or peripherals with a wired network or not.

If the computers on the wireless network need to be accessible by a wired network or need to share a peripheral,

such as a printer, with the wired network computers, the wireless network should be set up in Infrastructure

mode. The basis of Infrastructure mode centers around a wireless router or an access point, which serves as the

main point of communications in a wireless network. The Router transmits data to PCs equipped with wireless

network adapters, which can roam within a certain radial range of the Router. You can arrange the Router and

multiple access points to work in succession to extend the roaming range, and you can set up your wireless

network to communicate with your Ethernet hardware as well.

If the wireless network is relatively small and needs to share resources only with the other computers on the

wireless network, then the Ad-Hoc mode can be used. Ad-Hoc mode allows computers equipped with wireless

transmitters and receivers to communicate directly with each other, eliminating the need for a wireless router or

access point. The drawback of this mode is that in Ad-Hoc mode, wireless-equipped computers are not able to

communicate with computers on a wired network. And, of course, communication between the wireless-

equipped computers is limited by the distance and interference directly between them.

Network Layout

The Wireless-G Broadband Router has been specifically designed for use with both your 802.11b and 802.11g

products. Now, products using these standards can communicate with each other.

Chapter 2: Planning Your Wireless Network

Network Layout

Wireless-G Broadband Router with SpeedBooster

The Wireless-G Broadband Router is compatible with all 802.11b and 802.11g adapters, such as notebook

adapters for your laptop computers, PCI adapters for your desktop PCs, and USB adapters when you want to

enjoy USB connectivity. The Router will also communicate with the wireless print server and wireless Ethernet

bridges.

When you wish to connect your wireless network with your wired network, you can use the Wireless-G

Broadband Router’s four LAN ports. To add more ports, any of the Wireless-G Broadband Router's LAN ports can

be connected to any of Linksys's switches.

With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at

www.linksys.eu or linksys.com/international for more information about products that work with the Wireless-G

Broadband Router.

Chapter 3: Getting to Know the Wireless-G Broadband Router

The Back Panel

Wireless-G Broadband Router with SpeedBooster

Chapter 3: Getting to Know the Wireless-G Broadband

Router

The Back Panel

The Router's ports, where the cables are connected, are located on the back panel.

Reset Button There are two ways to reset the Router's factory defaults. Either press the Reset Button, for

approximately five seconds, or restore the defaults from the Administration tab - Factory

Defaults in the Router's Web-based Utility.

Internet The Internet port is where you will connect your broadband Internet connection.

1, 2, 3, 4 These ports (1, 2, 3, 4) connect the Router to PCs on your wired network and other Ethernet

network devices.

Power The Power port is where you will connect the power adapter.

IMPORTANT: Resetting the Router will erase

all of your settings (WEP Encryption, network

settings, etc.) and replace them with the

factory defaults. Do not reset the Router if you

want to retain these settings.

Figure 3-1: The Router’s Back Panel

Chapter 3: Getting to Know the Wireless-G Broadband Router

The Front Panel

Wireless-G Broadband Router with SpeedBooster

The Front Panel

The Router’s LEDs, where information about network activity is displayed, are located on the front panel.

(Cisco logo) Orange/White. The Cisco logo is the Router’s SecureEasySetup button. It lights up and will stay

orange when the Router is powered on. The color orange indicates that the Router is not using

the SecureEasySetup feature, while the color white indicates that the Router is using the

SecureEasySetup feature. When the Router enters SecureEasySetup mode, the Cisco logo will

turn white and start flashing. After the Router has generated the SSID and WPA Shared Key,

the Cisco logo will stop flashing and stay white.

To clear the SSID and WPA Shared Key, press and hold down the Cisco logo for five seconds.

The Cisco logo will flash slowly as the Router resets itself. The Cisco logo will turn orange to

indicate a successful reset.

Power Green. The Power LED lights up and will stay on while the Router is powered on. When the

Router goes through its self-diagnostic mode during every boot-up, this LED will flash. When

the diagnostic is complete, the LED will be solidly lit.

DMZ Green. The DMZ LED indicates when the DMZ function is being used. This LED will remain lit

as long as DMZ is enabled.

WLAN Green. The WLAN LED lights up when the wireless feature is enabled. If the LED is flashing,

the Router is actively sending or receiving data over the network.

1, 2, 3, 4 Green. These numbered LEDs, corresponding with the numbered ports on the Router’s back

panel, serve two purposes. If the LED is continuously lit, the Router is successfully connected

to a device through that port. A flashing LED indicates network activity over that port.

Internet Green. The Internet LED lights up when there is a connection made through the Internet port.

Figure 3-2: The Router’s Front Panel

NOTE: SecureEasySetup is a feature that makes it

easy to set up your wireless network. If you have

SecureEasySetup devices, run the Router’s Setup

Wizard CD-ROM and follow the on-screen

instructions to use SecureEasySetup. You can also

access SecureEasySetup from the Web-based Utility

if you don’t run the Setup Wizard.

Chapter 4: Connecting the Wireless-G Broadband Router

Overview

Wireless-G Broadband Router with SpeedBooster

Chapter 4: Connecting the Wireless-G Broadband Router

Overview

This chapter includes two sets of instructions. If the Wireless-G Broadband Router will be the only router in your

network, follow the instructions in “Hardware Installation for Connection to Your Broadband Modem.” You may

wish to run some applications for only certain PCs on your network and will need to run the Wireless-G

Broadband Router behind another router to do this. If you want to install the Wireless-G Broadband Router behind

another router in your network, follow the instructions in “Connecting One Router to Another.”

Hardware Installation for Connection to Your Broadband Modem

1. Power down your network devices.

2. Locate an optimum location for the Router. The best place for the Router is usually at the center of your

wireless network, with line of sight to all of your mobile stations.

3. Fix the direction of the antennas. Try to place the Router in a position that will best cover your wireless

network. Normally, the higher you place the antenna, the better the performance will be.

4. Connect a standard Ethernet network cable to the Router’s Internet port. Then, connect the other end of the

Ethernet cable to your cable or DSL broadband modem.

Figure 4-1: Connecting Your Modem to the Router’s Internet Port

Chapter 4: Connecting the Wireless-G Broadband Router

Hardware Installation for Connection to Your Broadband Modem

Wireless-G Broadband Router with SpeedBooster

5. Connect your network PCs or Ethernet devices to the Router’s numbered ports using standard Ethernet

network cabling.

6. Connect the power adapter to the Router’s Power port and the other end into an electrical outlet.

If you were supplied a power adapter and separate power cord, connect the power cord to the power adapter,

then connect the power adapter to the Router’s Power port. Plug the power cord into an electrical outlet.

Now that the hardware installation is complete, proceed to “Chapter 5: Configuring the Wireless-G

Broadband Router,” for directions on using the Router’s Web-Based Utility to configure the Router’s

settings for your network.

Figure 4-3: Connecting the Power

IMPORTANT: Make sure you use the power

adapter that is supplied with the Router. Use of a

different power adapter could damage the Router.

Figure 4-2: Connecting Your Network Devices

Chapter 4: Connecting the Wireless-G Broadband Router

Hardware Installation for Connection of One Router to Another

Wireless-G Broadband Router with SpeedBooster

Hardware Installation for Connection of One Router to Another

Some applications apply settings to all PCs connected to the Router. Sometimes, you may not want those

settings to apply to all settings in your network.

Before you connect one Router to another, you must make sure that both have different IP Addresses. This is

mandatory because both routers may be set to the same IP address by default, right out of the box.

First, make sure the Router is NOT connected to your network. Then follow these instructions:

1. To access the other router’s Web-based Utility, launch your web browser, and enter the other router’s default

IP address, 192.168.1.1, or whatever IP Address you have set it to, in the Address field. Then, press Enter.

2. A password request page will appear. Leave the User Name field blank. In the Password field, enter the

password you have set (the default password is admin). Then click the OK button.

3. The first screen that appears will display the Setup tab. In the Network Setup section, there is a setting called

Local IP Address, which is set to 192.168.1.1. Change this to 192.168.2.1.

4. Click the Save Settings button to save your change, and then exit the Web-based Utility.

5. Power down your network devices. Now you will begin the hardware installation of Broadband Router.

6. Locate an optimum location for the Broadband Router. The best place for the Broadband Router is usually at

the center of your wireless network, with line of sight to all of your mobile stations.

7. Fix the direction of the antennas. Try to place the Router in a position that will best cover your wireless

network. Normally, the higher you place the antenna, the better the performance will be.

Figure 4-5: Diagram for Connection to Another Router

NOTE: Steps 1-4 are instructions for a typical

Linksys router; however, if you are using a non-

Linksys router, refer to the other router’s

documentation for instructions on how to change its

local IP address to 192.168.2.1.

Internet

Broadband

Modem

Router

Wireless-G

Broadband

Router

Multiple PCs

Internet Broadband

Modem

Router Wireless-G

Broadband

Router

Figure 4-4: Connecting the Router Behind Another

Chapter 4: Connecting the Wireless-G Broadband Router

Hardware Installation for Connection of One Router to Another

Wireless-G Broadband Router with SpeedBooster

8. Connect a standard Ethernet network cable to the Broadband Router’s Internet port. Then, connect the other

end of the Ethernet cable to one of the numbered Ethernet ports on your other router.

9. Decide which network computers or Ethernet devices you want to connect to the Broadband Router.

Disconnect the selected computers or devices from the other router, and then connect them to the Broadband

Router’s numbered ports using standard Ethernet network cabling.

Figure 4-7: Connecting Your Network Devices

Figure 4-6: Connect the Broadband Router’s Internet Port to the other Router's Numbered Ethernet Port

Chapter 4: Connecting the Wireless-G Broadband Router

Hardware Installation for Connection of One Router to Another

Wireless-G Broadband Router with SpeedBooster

10. Connect the power adapter to the Router’s Power port and the other end into an electrical outlet.

If you were supplied a power adapter and separate power cord, connect the power cord to the power adapter,

then connect the power adapter to the Router’s Power port. Plug the power cord into an electrical outlet.

Now that the hardware installation is complete, proceed to “Chapter 5: Configuring the Wireless-G

Broadband Router,” for directions on using the Router’s Web-Based Utility to configure the Router’s

settings for your network.

Figure 4-8: Connecting the Power

IMPORTANT: Make sure you use the power

adapter that is supplied with the Router. Use of a

different power adapter could damage the Router.

Chapter 5: Configuring the Wireless-G Broadband Router

Overview

Wireless-G Broadband Router with SpeedBooster

Chapter 5: Configuring the Wireless-G Broadband

Router

Overview

You should always use the Setup CD-ROM when first installing the Router. If you do not wish to run the Setup

Wizard on the Setup CD-ROM, you can use the Web-based Utility to configure the Router. For advanced users, you

may configure the Router’s advanced settings through the Web-based Utility.

This chapter will describe each web page in the Utility and each page’s key functions. The utility can be accessed

via your web browser through use of a computer connected to the Router. For a basic network setup, most users

will use these two screens of the Utility:

• Basic Setup. On the Basic Setup screen, enter the settings provided by your ISP.

• Management. Click the Administration tab and then the Management tab. The Router’s default password is

admin. To secure the Router, change the Password from its default.

There are seven main tabs: Setup, Wireless, Security, Access Restrictions, Applications & Gaming, Administration,

and Status. Additional tabs will be available after you click one of the main tabs.

To access the Web-based Utility, launch Internet Explorer or Netscape Navigator, and enter the Router’s default IP

address, 192.168.1.1, in the Address field. Then, press Enter.

A password request page will appear. (Non-Windows XP users will see a similar screen.) Leave the User Name

field blank. The first time you open the Web-based Utility, use the default password admin. (You can set a new

password from the Administration tab’s Management screen.) Click the OK button to continue.

HAVE YOU: Enabled TCP/IP on your PCs? PCs

communicate over the network with this protocol.

Refer to “Appendix D: Windows Help” for more

information on TCP/IP.

NOTE: When first installing the Router, you should

use the Setup Wizard on the Setup CD-ROM. If you

want to configure advanced settings, use this

chapter to learn about the Web-based Utility.

Figure 5-1: Password Screen

Chapter 5: Configuring the Wireless-G Broadband Router

The Setup Tab - Basic Setup

Wireless-G Broadband Router with SpeedBooster

The Setup Tab - Basic Setup

The first screen that appears displays the Setup tab. This allows you to change the Router's general settings.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Internet Setup

The Internet Setup section configures the Router to your Internet connection. Most of this information can be

obtained through your ISP.

Internet Connection Type

Choose the type of Internet connection your ISP provides from the drop down menu.

• DHCP. By default, the Router’s Internet Connection Type is set to Automatic Configuration - DHCP, which

should be kept only if your ISP supports DHCP or you are connecting through a dynamic IP address.

• Static IP. If you are required to use a permanent IP address to connect to the Internet, select Static IP.

Internet IP Address. This is the Router’s IP address, when seen from the Internet. Your ISP will provide you

with the IP Address you need to specify here.

Subnet Mask. This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP

will provide you with the Subnet Mask.

Gateway. Your ISP will provide you with the Gateway Address, which is the ISP server’s IP address.

DNS. Your ISP will provide you with at least one DNS (Domain Name System) Server IP Address.

Figure 5-2: Setup Tab - Basic Setup

Figure 5-3: DHCP Connection Type

Figure 5-4: Static IP Connection Type

Chapter 5: Configuring the Wireless-G Broadband Router

The Setup Tab - Basic Setup

Wireless-G Broadband Router with SpeedBooster

• PPPoE. Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet

connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use

PPPoE. If they do, you will have to enable PPPoE.

User Name and Password. Enter the User Name and Password provided by your ISP.

Connect on Demand: Max Idle Time. You can configure the Router to cut the Internet connection after it has

been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated

due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as

soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio

button. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet

connection terminates.

Keep Alive Option: Redial Period. If you select this option, the Router will periodically check your Internet

connection. If you are disconnected, then the Router will automatically re-establish your connection. To use

this option, click the radio button next to Keep Alive. In the Redial Period field, you specify how often you want

the Router to check the Internet connection. The default Redial Period is 30 seconds.

• PPTP. Point-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe only.

Specify Internet IP Address. This is the Router’s IP address, as seen from the Internet. Your ISP will provide

you with the IP Address you need to specify here.

Subnet Mask. This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP

will provide you with the Subnet Mask.

Gateway. Your ISP will provide you with the Gateway Address.

User Name and Password. Enter the User Name and Password provided by your ISP.

Connect on Demand: Max Idle Time. You can configure the Router to cut the Internet connection after it has

been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated

due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as

soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio

button. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet

connection terminates.

Keep Alive Option: Redial Period. If you select this option, the Router will periodically check your Internet

connection. If you are disconnected, then the Router will automatically re-establish your connection. To use

this option, click the radio button next to Keep Alive. In the Redial Period field, you specify how often you want

the Router to check the Internet connection. The default Redial Period is 30 seconds.

Figure 5-5: PPPoE Connection Type

Figure 5-6: PPTP Connection Type

Chapter 5: Configuring the Wireless-G Broadband Router

The Setup Tab - Basic Setup

Wireless-G Broadband Router with SpeedBooster

• Telstra Cable. Telstra Cable is a service that applies to connections in Australia only.

User Name and Password. Enter the User Name and Password provided by your ISP.

Heart Beat Server. This is the IP address that the Router has, when seen from the Internet. Your ISP will

provide you with the IP Address you need to specify here.

Connect on Demand: Max Idle Time. You can configure the Router to cut the Internet connection after it has

been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated

due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as

soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio

button. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet

connection terminates.

Keep Alive Option: Redial Period. If you select this option, the Router will periodically check your Internet

connection. If you are disconnected, then the Router will automatically re-establish your connection. To use

this option, click the radio button next to Keep Alive. In the Redial Period field, you specify how often you want

the Router to check the Internet connection. The default Redial Period is 30 seconds.

• L2TP. L2TP is a service that applies to connections in Israel only.

User Name and Password. Enter the User Name and Password provided by your ISP.

L2TP Server. This is the IP address that the Router has, when seen from the Internet. Your ISP will provide you

with the IP Address you need to specify here.

Connect on Demand: Max Idle Time. You can configure the Router to cut the Internet connection after it has

been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated

due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as

soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio

button. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet

connection terminates.

Keep Alive Option: Redial Period. If you select this option, the Router will periodically check your Internet

connection. If you are disconnected, then the Router will automatically re-establish your connection. To use

this option, click the radio button next to Keep Alive. In the Redial Period field, you specify how often you want

the Router to check the Internet connection. The default Redial Period is 30 seconds.

Figure 5-7: Telstra Cable Connection Type

Figure 5-8: L2TP Connection Type

Chapter 5: Configuring the Wireless-G Broadband Router

The Setup Tab - Basic Setup

Wireless-G Broadband Router with SpeedBooster

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Router Name. In this field, you can type a name of up to 39 characters to represent the Router.

Host Name/Domain Name. These fields allow you to supply a host and domain name for the Router. Some ISPs,

usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your

broadband Internet service has been configured with a host and domain name. In most cases, leaving these

fields blank will work.

MTU. MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet

transmission. You should leave this value in the 1200 to 1500 range. To have the Router select the best MTU for

your Internet connection, select Auto. The default setting is Auto.

Network Setup

The Network Setup section changes the settings on the network connected to the Router’s Ethernet ports.

Wireless Setup is performed through the Wireless tab.

Router IP

This presents both the Router’s IP Address and Subnet Mask as seen by your network.

Network Address Server Settings (DHCP)

The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The

Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to

each computer on your network. If you choose to enable the Router’s DHCP server option, you must configure all

of your network PCs to connect to a DHCP server (the Router), and make sure there is no other DHCP server on

your network.

DHCP Server. DHCP is enabled by factory default. If you already have a DHCP server on your network, or you

don’t want a DHCP server, then click the Disable radio button (no other DHCP features will be available).

Starting IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. Because the

Router’s default IP address is 192.168.1.1, the Starting IP Address must be 192.168.1.2 or greater, but smaller

than 192.168.1.253. The default Starting IP Address is 192.168.1.100.

Maximum Number of DHCP Users. Enter the maximum number of PCs that you want the DHCP server to assign

IP addresses to. This number cannot be greater than 253. The default is 50.

Figure 5-11: Network Address Server Settings

Figure 5-10: Router IP

Figure 5-9: Optional Settings

Chapter 5: Configuring the Wireless-G Broadband Router

The Setup Tab - Basic Setup

Wireless-G Broadband Router with SpeedBooster

Client Lease Time. The Client Lease Time is the amount of time a network user will be allowed connection to the

Router with their current dynamic IP address. Enter the amount of time, in minutes, that the user will be “leased”

this dynamic IP address. After the time is up, the user will be automatically assigned a new dynamic IP address.

The default is 0 minutes, which means one day.

Static DNS (1-3). The Domain Name System (DNS) is how the Internet translates domain or website names into

Internet addresses or URLs. Your ISP will provide you with at least one DNS Server IP Address. If you wish to use

another, type that IP Address in one of these fields. You can type up to three DNS Server IP Addresses here. The

Router will use these for quicker access to functioning DNS servers.

WINS. The Windows Internet Naming Service (WINS) manages each PC’s interaction with the Internet. If you use

a WINS server, enter that server’s IP Address here. Otherwise, leave this blank.

Time Setting

Change the time zone in which your network functions from this pull-down menu. (You can even automatically

adjust for daylight savings time.)

Figure 5-12: Time Setting

Chapter 5: Configuring the Wireless-G Broadband Router

The Setup Tab - DDNS

Wireless-G Broadband Router with SpeedBooster

The Setup Tab - DDNS

The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain

name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other

server behind the Router.

Before you can use this feature, you need to sign up for DDNS service with a DDNS service provider,

www.dyndns.org or www.TZO.com. If you do not want to use this feature, keep the default setting, Disable.

DDNS

DDNS Service

If your DDNS service is provided by DynDNS.org, then select DynDNS.org from the drop-down menu. If your

DDNS service is provided by TZO, then select TZO.com. The features available on the DDNS screen will vary,

depending on which DDNS service provider you use.

DynDNS.org

DDNS Service. From this pull-down menu, enter the DDNS service with which you have membership.

User Name. Enter the User Name for your DDNS account

Password. Enter the Password for your DDNS account.

Host Name. The is the DDNS URL assigned by the DDNS service.

Internet IP Address. This is the Router’s current IP Address as seen on the Internet.

Status. This displays the status of the DDNS connection.

TZO.com

E-mail Address, TZO Key, and Domain Name. Enter the settings of the account you set up with TZO.

Internet IP Address. The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.

Status. The status of the DDNS service connection is displayed here.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Figure 5-13: Setup Tab - DDNS - DynDNS

Figure 5-14: Setup Tab - DDNS - TZO

Chapter 5: Configuring the Wireless-G Broadband Router

The Setup Tab - MAC Address Clone

Wireless-G Broadband Router with SpeedBooster

The Setup Tab - MAC Address Clone

A MAC address is a 12-digit code assigned to a unique piece of hardware for identification. Some ISPs will

require you to register a MAC address in order to access the Internet. If you do not wish to re-register the MAC

address with your ISP, you may assign the MAC address you have currently registered with your ISP to the Router

with the MAC Address Clone feature.

Enable/Disable. To have the MAC Address cloned, click the radio button beside Enable.

User Defined Entry. Enter the MAC Address registered with your ISP here.

Clone Your PC’s MAC Address. Clicking this button will clone the MAC address.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Figure 5-15: Setup Tab - MAC Address Clone

Chapter 5: Configuring the Wireless-G Broadband Router

The Setup Tab - Advanced Routing

Wireless-G Broadband Router with SpeedBooster

The Setup Tab - Advanced Routing

This tab is used to set up the Router’s advanced functions. Operating Mode allows you to select the type(s) of

advanced functions you use. Dynamic Routing will automatically adjust how packets travel on your network. Static

Routing sets up a fixed route to another network destination.

Operating Mode

. Select the mode in which this Router will function. If this Router is hosting your network’s

connection to the Internet, select

Gateway

. If another Router exists on your network, select

Router

. When Router is

chosen,

Dynamic Routing

will be available as an option.

Dynamic Routing

. This feature enables the Router to automatically adjust to physical changes in the network’s

layout and exchange routing tables with the other router(s). The Router determines the network packets’ route

based on the fewest number of hops between the source and the destination. This feature is

Disabled

by default.

From the drop-down menu, you can also select

LAN & Wireless

, which performs dynamic routing over your

Ethernet and wireless networks. You can also select

WAN

, which performs dynamic routing with data coming from

the Internet. Finally, selecting

Both

enables dynamic routing for both networks, as well as data from the Internet.

Static Routing

. To set up a static route between the Router and another network, select a number from the Static

Routing drop-down list. (A static route is a pre-determined pathway that network information must travel to reach a

specific host or network.) Enter the information described below to set up a new static route. (Click the

Delete This

Entry

button to delete a static route.)

Enter Route Name

. Enter a name for the Route here, using a maximum of 25 alphanumeric characters.

Destination LAN IP

. The Destination LAN IP is the address of the remote network or host to which you want to

assign a static route.

Subnet Mask

. The Subnet Mask determines which portion of a Destination LAN IP address is the network

portion, and which portion is the host portion.

Default Gateway

. This is the IP address of the gateway device that allows for contact between the Router and

the remote network or host.

Interface

. This interface tells you whether the Destination IP Address is on the

LAN & Wireless

(Ethernet and

wireless networks), the

WAN

(Internet), or

Loopback

(a dummy network in which one PC acts like a network—

necessary for certain software programs).

Click the

Show Routing Table

button to view the Static Routes you’ve already set up.

Change these settings as described here and click the

Save Settings

button to apply your changes or

Cancel

Changes

to cancel your changes.

Figure 5-16: Setup Tab - Advanced Routing (Gateway)

Figure 5-17: Setup Tab - Advanced Routing (Router)

Chapter 5: Configuring the Wireless-G Broadband Router

The Wireless Tab - Basic Wireless Settings

Wireless-G Broadband Router with SpeedBooster

The Wireless Tab - Basic Wireless Settings

The basic settings for wireless networking are set on this screen.

Wireless Network Mode. From this drop-down menu, you can select the wireless standards running on your

network. If you have both 802.11g and 802.11b devices in your network, keep the default setting, Mixed. If you

have only 802.11g devices, select G-Only. If you have only 802.11b devices, select B-Only. If you do not have any

802.11g and 802.11b devices in your network, select Disable. SpeedBooster works automatically with all

settings, providing the added bonus of increased speed across your entire network and even greater speed when

using SpeedBooster products only.

Wireless Network Name (SSID). The SSID is the network name shared among all points in a wireless network.

The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32

characters (use any of the characters on the keyboard). Make sure this setting is the same for all points in your

wireless network. For added security, you should change the default SSID (linksys) to a unique name.

Wireless Channel. Select the appropriate channel from the list provided to correspond with your network

settings. All devices in your wireless network must be broadcast on the same channel in order to function

correctly.

Wireless SSID Broadcast. When wireless clients survey the local area for wireless networks to associate with,

they will detect the SSID broadcast by the Router. To broadcast the Router's SSID, keep the default setting,

Enable. If you do not want to broadcast the Router's SSID, then select Disable.

SecureEasySetup. If you did not utilize this network connection feature during the Setup Wizard, you may use it

here by clicking the green logo. When you are prompted to start the push button setup, click Okay.

Reset Security. Use this button to reset the security settings on your network. You will need to run

SecureEasySetup again on each device on your network to re-associate it to your network.

When you have finished configuring the devices in your wireless network, click the Next button to continue.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Figure 5-18: Wireless Tab - Basic Wireless Settings

NOTE: SpeedBooster ONLY works in Infrastructure

Mode.

Chapter 5: Configuring the Wireless-G Broadband Router

The Wireless Tab - Wireless Security

Wireless-G Broadband Router with SpeedBooster

The Wireless Tab - Wireless Security

The Wireless Security settings configure the security of your wireless network. There are six wireless security

mode options supported by the Router: WPA Personal, WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS,

and WEP. (WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption.

WEP stands for Wired Equivalent Privacy, while RADIUS stands for Remote Authentication Dial-In User Service.)

These six are briefly discussed here. For detailed instructions on configuring wireless security for the Router, turn

to “Appendix B: Wireless Security.”

WPA Personal. WPA gives you two encryption methods, TKIP and AES, with dynamic encryption keys. Select the

type of algorithm, TKIP or AES. Enter a WPA Shared Key of 8-63 characters. Then enter a Group Key Renewal

period, which instructs the Router how often it should change the encryption keys.

WPA Enterprise. This option features WPA used in coordination with a RADIUS server. (This should only be used

when a RADIUS server is connected to the Router.) First, select the type of WPA algorithm you want to use, TKIP

or AES. Enter the RADIUS server’s IP Address and port number, along with a key shared between the Router and

the server. Last, enter a Key Renewal Timeout, which instructs the Router how often it should change the

encryption keys.

Figure 5-19: Wireless Tab - Wireless Security

(WPA Personal)

Figure 5-20: Wireless Tab - Wireless Security

(WPA Enterprise)

IMPORTANT: If you are using WPA, always

remember that each device in your wireless

network MUST use the same WPA method

and shared key, or else the network will not

function properly.

Chapter 5: Configuring the Wireless-G Broadband Router

The Wireless Tab - Wireless Security

Wireless-G Broadband Router with SpeedBooster

WPA2 Personal. WPA2 gives you two encryption methods, TKIP and AES, with dynamic encryption keys. Select

the type of algorithm, AES, or TKIP + AES. Enter a WPA Shared Key of 8-63 characters. Then enter a Group Key

Renewal period, which instructs the Router how often it should change the encryption keys.

WPA2 Enterprise. This option features WPA2 used in coordination with a RADIUS server. (This should only be

used when a RADIUS server is connected to the Router.) First, select the type of WPA algorithm you want to use,

AES, or TKIP + AES. Enter the RADIUS server’s IP Address and port number, along with a key shared between the

Router and the server. Last, enter a Key Renewal Timeout, which instructs the Router how often it should change

the encryption keys.

Figure 5-21: Wireless Tab - Wireless Security (WPA2

Personal)

Figure 5-22: Wireless Tab - Wireless Security (WPA2

Enterprise)

Chapter 5: Configuring the Wireless-G Broadband Router

The Wireless Tab - Wireless Security

Wireless-G Broadband Router with SpeedBooster

RADIUS. This option features WEP used in coordination with a RADIUS server. (This should only be used when a

RADIUS server is connected to the Router.) First, enter the RADIUS server’s IP Address and port number, along

with a key shared between the Router and the server. Then, select a Default Transmit Key (choose which Key to

use), and a level of WEP encryption, 64 bits 10 hex digits or 128 bits 26 hex digits. Last, either generate a

WEP key using the Passphrase or enter the WEP key manually.

WEP. WEP is a basic encryption method, which is not as secure as WPA. To use WEP, select a Default Transmit

Key (choose which Key to use), and a level of WEP encryption, 64 bits 10 hex digits or 128 bits 26 hex digits.

Then either generate a WEP key using the Passphrase or enter the WEP key manually.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes. For detailed instructions on configuring wireless security for the Router, turn to

“Appendix B: Wireless Security.”

Figure 5-23: Wireless Tab - Wireless Security (RADIUS)

Figure 5-24: Wireless Tab - Wireless Security (WEP)

IMPORTANT: If you are using WEP encryption,

always remember that each device in your wireless

network MUST use the same WEP encryption

method and encryption key, or else your wireless

network will not function properly.

Chapter 5: Configuring the Wireless-G Broadband Router

The Wireless Tab - Wireless MAC Filter

Wireless-G Broadband Router with SpeedBooster

The Wireless Tab - Wireless MAC Filter

Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your

network’s radius.

Wireless MAC Filter. To filter wireless users by MAC Address, either permitting or blocking access, click Enable.

If you do not wish to filter users by MAC Address, select Disable.

Prevent. Clicking this button will block wireless access by MAC Address.

Permit Only. Clicking this button will allow wireless access by MAC Address.

Edit MAC Address Filter List. Clicking this button will open the MAC Address Filter List. On this screen, you can

list users, by MAC Address, to whom you wish to provide or block access. For easy reference, click the Wireless

Client MAC List button to display a list of network users by MAC Address.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Figure 5-26: MAC Address Filter List

Figure 5-25: Wireless Tab - Wireless MAC Filter

Chapter 5: Configuring the Wireless-G Broadband Router

The Wireless Tab - Advanced Wireless Settings

Wireless-G Broadband Router with SpeedBooster

The Wireless Tab - Advanced Wireless Settings

This tab is used to set up the Router’s advanced wireless functions. These settings should only be adjusted by an

expert administrator as incorrect settings can reduce wireless performance.

Authentication Type. The default is set to Auto, which allows either Open System or Shared Key authentication

to be used. With Open System authentication, the sender and the recipient do NOT use a WEP key for

authentication. With Shared Key authentication, the sender and recipient use a WEP key for authentication.

Basic Rate. The Basic Rate setting is not actually one rate of transmission but a series of rates at which the

Router can transmit. The Router will advertise its Basic Rate to the other wireless devices in your network, so

they know which rates will be used. The Router will also advertise that it will automatically select the best rate

for transmission. The default setting is Default, when the Router can transmit at all standard wireless rates

(1-2Mbps, 5.5Mbps, 11Mbps, 18Mbps, and 24Mbps). Other options are 1-2Mbps, for use with older wireless

technology, and All, when the Router can transmit at all wireless rates. The Basic Rate is not the actual rate of

data transmission. If you want to specify the Router’s rate of data transmission, configure the Transmission Rate

setting.

Transmission Rate. The rate of data transmission should be set depending on the speed of your wireless

network. You can select from a range of transmission speeds, or you can select Auto to have the Router

automatically use the fastest possible data rate and enable the Auto-Fallback feature. Auto-Fallback will

negotiate the best possible connection speed between the Router and a wireless client. The default value is Auto.

CTS Protection Mode. CTS (Clear-To-Send) Protection Mode should remain disabled unless you are having

severe problems with your Wireless-G products not being able to transmit to the Router in an environment with

heavy 802.11b traffic. This function boosts the Router’s ability to catch all Wireless-G transmissions but will

severely decrease performance.

Frame Burst. Enabling this option should provide your network with greater performance, depending on the

manufacturer of your wireless products. If you are not sure how to use this option, keep the default, Disable.

Beacon Interval. The default value is 100. Enter a value between 1 and 65,535 milliseconds. The Beacon Interval

value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize

the wireless network.

DTIM Interval. This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message

(DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and

multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it

sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast

and multicast messages. The default value is 1.

Figure 5-27: Wireless Tab - Advanced Wireless Settings

Chapter 5: Configuring the Wireless-G Broadband Router

The Wireless Tab - Advanced Wireless Settings

Wireless-G Broadband Router with SpeedBooster

Fragmentation Threshold. This value specifies the maximum size for a packet before data is fragmented into

multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation

Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor

reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.

RTS Threshold. Should you encounter inconsistent data flow, only minor reduction of the default value, 2347, is

recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will

not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates

the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS)

frame to acknowledge the right to begin transmission. The RTS Threshold value should remain at its default value

of 2347.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Chapter 5: Configuring the Wireless-G Broadband Router

The Security Tab - Firewall

Wireless-G Broadband Router with SpeedBooster

The Security Tab - Firewall

Firewall Protection. Enable this feature to employ Stateful Packet Inspection (SPI) for more detailed review of

data packets entering your network environment.

Block WAN Requests. Enable the Block WAN Request feature by checking the box beside Block Anonymous

Internet Requests and you can prevent your network from being “pinged,” or detected, by other Internet users.

The Block WAN Request feature also reinforces your network security by hiding your network ports. Both

functions of the Block WAN Request feature make it more difficult for outside users to work their way into your

network. This feature is enabled by default. Select Disabled to allow anonymous Internet requests.

Filter Multicast. Multicasting allows for multiple transmissions to specific recipients at the same time. If

multicasting is permitted, then the Router will allow IP multicast packets to be forwarded to the appropriate

computers. Select Enabled to filter multicasting, or Disabled to disable this feature.

Filter Internet NAT Redirection. This feature uses port forwarding to block access to local servers from local

networked computers. Select Enabled to filter Internet NAT redirection, or Disabled to disable this feature.

Filter IDENT (Port 113). This feature keeps port 113 from being scanned by devices outside of your local

network. Select Enabled to filter port 113, or Disabled to disable this feature.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Figure 5-28: Security Tab - Firewall

Chapter 5: Configuring the Wireless-G Broadband Router

The Security Tab - VPN Passthrough

Wireless-G Broadband Router with SpeedBooster

The Security Tab - VPN Passthrough

Use the settings on this tab to allow VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the

Router’s firewall.

IPSec Pass-through. Internet Protocol Security (IPSec) is a suite of protocols used to implement secure

exchange of packets at the IP layer. To allow IPSec tunnels to pass through the Router, click Enable. IPSec Pass-

Through is enabled by default.

PPTP Pass-through. Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point Protocol (PPP) to be

tunneled through an IP network. To allow PPTP tunnels to pass through the Router, click Enable. PPTP Pass-

Through is enabled by default.

L2TP Pass-through. Layer 2 Tunneling Protocol is the method used to enable Point-to-Point sessions via the

Internet on the Layer 2 level. To allow L2TP tunnels to pass through the Router, click Enable. L2TP Pass-Through

is enabled by default.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Figure 5-29: Security Tab - VPN Passthrough

Chapter 5: Configuring the Wireless-G Broadband Router

The Access Restrictions Tab - Internet Access

Wireless-G Broadband Router with SpeedBooster

The Access Restrictions Tab - Internet Access

The Internet Access screen allows you to block or allow specific kinds of Internet usage and traffic, such as

Internet access, designated services, websites, and inbound traffic during specific days and times.

Internet Access Policy. Access can be managed by a policy. Use the settings on this screen to establish an

access policy (after the Save Settings button is clicked). Selecting a policy from the drop-down menu will

display that policy’s settings. To delete a policy, select that policy’s number and click the Delete button. To view

all the policies, click the Summary button. (Policies can be deleted from the Summary screen by selecting the

policy or policies and clicking the Delete button. To return to the Internet Access tab, click the Close button.)

Status. Policies are disabled by default. To enable a policy, select the policy number from the drop-down menu,

and click the radio button beside Enable.

To create an Internet Access policy:

1. Select a number from the Internet Access Policy drop-down menu.

2. To enable this policy, select Enable

3. Enter a Policy Name in the field provided.

4. Click the Edit List of PCs button to select which PCs will be affected by the policy. The List of PCs screen will

appear. You can select a PC by MAC Address or IP Address. You can also enter a range of IP Addresses if you

want this policy to affect a group of PCs. After making your changes, click the Save Settings button to apply

your changes or Cancel Changes to cancel your changes. Then click the Close button.

5. Click the appropriate option, Deny or Allow, depending on whether you want to block or allow Internet access

for the PCs you listed on the List of PCs screen.

6. Decide which days and what times you want this policy to be enforced. Select the individual days during

which the policy will be in effect, or select Everyday. Then enter a range of hours and minutes during which

the policy will be in effect, or select 24 Hours.

7. Select any Blocked Services or Website Blocking you wish to use.

Figure 5-30: Access Restrictions Tab - Internet Access

Figure 5-31: Internet Policy Summary

Figure 5-32: List of PCs

Chapter 5: Configuring the Wireless-G Broadband Router

The Access Restrictions Tab - Internet Access

Wireless-G Broadband Router with SpeedBooster

Blocked Services

You can filter access to various services accessed over the Internet, such as FTP or telnet, by selecting services

from the drop-down menus next to Blocked Services. (You can block up to 20 services.)

Then enter the range of ports you want to filter.

If the service you want to block is not listed or you want to edit a service’s settings, then click the Add/Edit

Service button. Then the Port Services screen will appear.

To add a service, enter the service’s name in the Service Name field. Select its protocol from the Protocol drop-

down menu, and enter its range in the Port Range fields. Then click the Add button.

To modify a service, select it from the list on the right. Change its name, protocol setting, or port range. Then click

the Modify button.

To delete a service, select it from the list on the right. Then click the Delete button.

When you are finished making changes on the Port Services screen, click the Apply button to save changes. If

you want to cancel your changes, click the Cancel button. To close the Port Services screen and return to the

Access Restrictions screen, click the Close button.

Website Blocking by URL Address

If you want to block websites with specific URL addresses, enter each URL in a separate field next to Website

Blocking by URL Address.

Website Blocking by Keyword

If you want to block websites using specific keywords, enter each keyword in a separate field next to Website

Blocking by Keyword.

Click the Save Settings button to save the policy’s settings. To cancel the policy’s settings, click the Cancel

Changes button.

Figure 5-33: Port Services

Chapter 5: Configuring the Wireless-G Broadband Router

The Applications and Gaming Tab - Port Range Forward

Wireless-G Broadband Router with SpeedBooster

The Applications and Gaming Tab - Port Range Forward

The Applications and Gaming Tab allows you to set up public services on your network, such as web servers, ftp

servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any

applications that use Internet access to perform functions such as videoconferencing or online gaming. Some

Internet applications may not require any forwarding.)

To forward a port, enter the information on each line for the criteria required. Descriptions of each criteria are

described here.

Application. In this field, enter the name you wish to give the application. Each name can be up to 12 characters.

Start/End. This is the port range. Enter the number that starts the port range under Start and the number that

ends the range under End.

Protocol. Enter the protocol used for this application, either TCP or UDP, or Both.

IP Address. For each application, enter the IP Address of the PC running the specific application.

Enable. Click the Enable checkbox to enable port forwarding for the relevant application.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Figure 5-34: Applications and Gaming Tab -

Port Range Forward

Chapter 5: Configuring the Wireless-G Broadband Router

The Applications & Gaming Tab - Port Triggering

Wireless-G Broadband Router with SpeedBooster

The Applications & Gaming Tab - Port Triggering

The Port Triggering screen allows the Router to watch outgoing data for specific port numbers. The IP address of

the computer that sends the matching data is remembered by the Router, so that when the requested data

returns through the Router, the data is pulled back to the proper computer by way of IP address and port mapping

rules.

Port Triggering

Application. Enter the application name of the trigger.

Triggered Range

For each application, list the triggered port number range. Check with the Internet application documentation for

the port number(s) needed.

Start Port. Enter the starting port number of the Triggered Range.

End Port. Enter the ending port number of the Triggered Range.

Forwarded Range

For each application, list the forwarded port number range. Check with the Internet application documentation for

the port number(s) needed.

Start Port. Enter the starting port number of the Forwarded Range.

End Port. Enter the ending port number of the Forwarded Range.

Enable. Select Enable to enable port triggering for the applicable application.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Figure 5-35: Applications and Gaming Tab - Port

Triggering

Chapter 5: Configuring the Wireless-G Broadband Router

The Applications and Gaming Tab - DMZ

Wireless-G Broadband Router with SpeedBooster

The Applications and Gaming Tab - DMZ

The DMZ feature allows one network user to be exposed to the Internet for use of a special-purpose service such

as Internet gaming or videoconferencing. DMZ hosting forwards all the ports at the same time to one PC. The Port

Range Forward feature is more secure because it only opens the ports you want to have opened, while DMZ

hosting opens all the ports of one computer, exposing the computer to the Internet.

Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static

IP address assigned to it because its IP address may change when using the DHCP function.

To expose one PC, select Enable. Then, enter the computer's IP address in the DMZ Host IP Address field.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

The Applications and Gaming Tab - QoS

Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve

demanding, real-time applications, such as videoconferencing.

There are three types of QoS available: Device Priority, Ethernet Port Priority, and Application Priority.

Enable/Disable. To enable QoS, select Enable. Otherwise, select Disable.

Upstream Bandwidth. Select Auto or Manual from the drop-down menu. Manual allows you to specify the

maximum outgoing bandwidth that applications can utilize.

Device Priority

Enter the name of your network device in the Device name field, enter its MAC Address, then select its priority

from the drop-down menu.

Ethernet Port Priority

Ethernet Port Priority QoS allows you to prioritize performance for the Router’s four ports, LAN Ports 1-4. For each

of these ports, select High or Low for Priority. The Router’s four ports have been assigned low priority by default.

For Flow Control, if you want the Router to control the transmission of data between network devices, select

Figure 5-36: Applications and Gaming Tab - DMZ

Figure 5-37: Applications and Gaming Tab - QOS

Chapter 5: Configuring the Wireless-G Broadband Router

The Applications and Gaming Tab - QoS

Wireless-G Broadband Router with SpeedBooster

Enable. To disable this feature, select Disable. Ethernet Port Priority QoS does not require support from your ISP

because the prioritized ports LAN ports 1-4 are in your network.

Application Port Priority

Application Port Priority QoS manages information as it is transmitted and received. Depending on the settings of

the QoS screen, this feature will assign information a high or low priority for the applications that you specify.

Application Name. Enter the name you wish to give the application in the Application Name field.

Priority. Select High or Low to assign priority to the application.

Specific Port #. Enter the port number for the application.

Optimize Gaming Applications. Select this to automatically allow common game application ports to have a

higher priority. These games include, but are not limited to: Counter-Strike, Half-Life, Age of Empires, Everquest,

Quake2/Quake3 and Diablo II, etc. The default setting is unselected.

Wireless QoS

WMM Support. Wi-Fi Multimedia (WMM), formerly known as Wireless Multimedia Extensions (WME), is a Wi-Fi

Alliance certified feature, based on the IEEE 802.11e draft standard. This feature provides QoS to wireless

networks. It is especially suitable for voice, music and video applications; for example, Voice over IP (VoIP), video

streaming, and interactive gaming. If you have other devices on your wireless network that support WMM, select

Enabled. Otherwise, keep the default, Disabled.

No Acknowledgement. This feature prevents the Router from re-sending data if an error occurs. To use this

feature, select Enabled. Otherwise, keep the default setting, Disabled.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Chapter 5: Configuring the Wireless-G Broadband Router

The Administration Tab - Management

Wireless-G Broadband Router with SpeedBooster

The Administration Tab - Management

This section of the Administration tab allows the network’s administrator to manage specific Router functions for

access and security.

Local Router Access. You can change the Router’s password from here. Enter a new Router password and then

type it again in the Re-enter to confirm field to confirm.

Web Access. HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on

the World Wide Web. HTTPS - Uses SSL (Secured Socket Layer) to encrypt data transmitted for higher security.

Select HTTP or HTTPS. Wireless Access Web - If you are using your Wireless Router in a public domain where you

are giving wireless access to your guests, you can disable wireless access to the router’s web-based utility. You

will only be able to access the web-based utility via a wired connection if you disable the setting. Select Enable

to enable wireless access to the Router’s web-based utility or Disable to disable wireless access to the utility.

Remote Router Access. To access the Router remotely, from outside the network, select Enable. Then, enter the

port number that will be open to outside access. You will need to enter the Router’s password when accessing

the Router this way, as usual.

UPnP. Select Enable to enable UPnP feature; otherwise, select Disable. This feature is enabled by default.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

The Administration Tab - Log

The Router can keep logs of all traffic for your Internet connection. To disable the Log function, keep the default

setting, Disable. To monitor traffic between the network and the Internet, select Enable. When you wish to view

the logs, click Incoming Log or Outgoing Log, depending on which you wish to view.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Figure 5-38: Administration Tab - Management

Figure 5-39: Administration Tab - Log

Chapter 5: Configuring the Wireless-G Broadband Router

The Administration Tab - Diagnostics

Wireless-G Broadband Router with SpeedBooster

The Administration Tab - Diagnostics

The diagnostic tests (Ping and Traceroute) allow you to check the connections of your network components.

Ping Test. The Ping test will check the status of a connection. Click the Ping button to open the Ping Test screen.

Enter the address of the PC whose connection you wish to test and how many times you wish to test it. Then,

click the Ping button. The Ping Test screen will show if the test was successful. To stop the test, click the Stop

button. Click the Clear Log button to clear the screen. Click the Close button to return to the Diagnostics screen.

Traceroute Test. To test the performance of a connect, click the Traceroute button. Enter the address of the PC

whose connection you wish to test and click the Ping button. The Traceroute Test screen will show if the test was

successful. To stop the test, click the Stop button. Click the Clear Log button to clear the screen. Click the Close

button to return to the Diagnostics screen.

Figure 5-40: Administration Tab - Diagnostics

Figure 5-41: The Ping Test

Figure 5-42: The Traceroute Test

Chapter 5: Configuring the Wireless-G Broadband Router

The Administration Tab - Factory Defaults

Wireless-G Broadband Router with SpeedBooster

The Administration Tab - Factory Defaults

Select Yes, and then click the Save Settings button to reset all configuration settings to their default values. Any

settings you have saved will be lost when the default settings are restored

The Administration Tab - Firmware Upgrade

Firmware can be upgraded by clicking the Upgrade button after browsing for the firmware, which you can

download from the Linksys website. Do not upgrade your firmware unless you are experiencing problems with

the Router. For more information about upgrading firmware, refer to “Appendix C: Upgrading Firmware”.

Figure 5-44: Administration Tab - Firmware Upgrade

Figure 5-43: Administration Tab - Factory Defaults

Chapter 5: Configuring the Wireless-G Broadband Router

The Administration Tab - Config Management

Wireless-G Broadband Router with SpeedBooster

The Administration Tab - Config Management

This screen is used to back up or restore the Router’s configuration file.

To back up the Router’s configuration file, click the Backup button. Then follow the on-screen instructions.

To restore the Router’s configuration file, click the Browse button to locate the file, and follow the on-screen

instructions. After you have selected the file, click the Restore button.

Figure 5-45: Administration Tab - Config Management

Chapter 5: Configuring the Wireless-G Broadband Router

The Status Tab - Router

Wireless-G Broadband Router with SpeedBooster

The Status Tab - Router

The Router screen on the Status Tab displays the Router’s current status.

Firmware Version. This is the Router’s current firmware.

Current Time. This shows the time, as you set on the Setup Tab.

MAC Address. This is the Router’s MAC Address, as seen by your ISP.

Router Name. This is the specific name for the Router, which you set on the Setup Tab.

Host Name. If required by your ISP, this would have been entered on the Setup Tab.

Domain Name. If required by your ISP, this would have been entered on the Setup Tab.

Configuration Type. This section shows the current network information stored in the Router. The information

varies depending on the Internet connection type selected on the Setup tab.

Figure 5-46: Status Tab - Router

Chapter 5: Configuring the Wireless-G Broadband Router

The Status Tab - Local Network

Wireless-G Broadband Router with SpeedBooster

The Status Tab - Local Network

The Local Network screen on the Status Tab displays the status of your network.

MAC Address. This is the Router’s MAC Address, as seen on your local, Ethernet network.

IP Address. This shows the Router’s IP Address, as it appears on your local, Ethernet network.

Subnet Mask. This shows the current subnet mask being configured for your local network.

DHCP Server. If you are using the Router as a DHCP server, that will be displayed here.

Start IP Address. For the range of IP Addresses used by devices on your local, Ethernet network, the beginning

of that range is shown here.

End IP Address. For the range of IP Addresses used by devices on your local, Ethernet network, the end of that

range is shown here.

DHCP Clients Table. Clicking this button will open a screen to show you which PCs are utilizing the Router as a

DHCP server. You can delete PCs from that list, and sever their connections, by checking a Delete box and

clicking the Delete button.

Figure 5-47: Status Tab - Local Network

Figure 5-48: DHCP Clients Table

Chapter 5: Configuring the Wireless-G Broadband Router

The Status Tab - Wireless

Wireless-G Broadband Router with SpeedBooster

The Status Tab - Wireless

The Wireless screen on the Status Tab displays the status of your wireless network.

MAC Address. This is the Router’s MAC Address, as seen on your local, wireless network.

Mode. As selected from the Wireless tab, this will display the wireless mode (Mixed, G-Only, or Disabled) used by

the network.

SSID. As entered on the Wireless tab, this will display the wireless network name or SSID.

DHCP Server. If you are using the Router as a DHCP server, that will be displayed here.

Channel. As entered on the Wireless tab, this will display the channel on which your wireless network is

broadcasting.

Encryption Function. As selected on the Security Tab, this will display what type of encryption the Router uses

for security.

Figure 5-49: Status Tab - Wireless

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-G Broadband Router with SpeedBooster

Appendix A: Troubleshooting

This appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.”

Provided are possible solutions to problems that may occur during the installation and operation of the Router.

Read the descriptions below to help you solve your problems. If you can’t find an answer here, check the Linksys

website at www.linksys.eu or linksys.com/international.

Common Problems and Solutions

1. I’m trying to access the Router’s Web-based Utility, but I do not see the login screen. Instead, I see a

screen saying, “404 Forbidden.”

If you are using Windows Explorer, perform the following steps until you see the Web-based Utility’s login

screen (Netscape Navigator will require similar steps):

1. Click File. Make sure Work Offline is NOT checked.

2. Press CTRL + F5. This is a hard refresh, which will force Windows Explorer to load new webpages,

not cached ones.

3. Click Tools. Click Internet Options. Click the Security tab. Click the Default level button. Make sure

the security level is Medium or lower. Then click the OK button.

2. I need to set a static IP address on a PC.

You can assign a static IP address to a PC by performing the following steps:

• For Windows 98SE and Me:

1. Click Start, Settings, and Control Panel. Double-click Network.

2. In The following network components are installed box, select the TCP/IP-> associated with your

Ethernet adapter. If you only have one Ethernet adapter installed, you will only see one TCP/IP line

with no association to an Ethernet adapter. Highlight it and click the Properties button.

3. In the TCP/IP properties window, select the IP address tab, and select Specify an IP address. Enter

a unique IP address that is not used by any other computer on the network connected to the Router.

Make sure that each IP address is unique for each PC or network device.

4. Click the Gateway tab, and in the New Gateway prompt, enter 192.168.1.1, which is the default IP

address of the Router. Click the Add button to accept the entry.

5. Click the DNS tab, and make sure the DNS Enabled option is selected. Enter the Host and Domain

names (e.g., John for Host and home for Domain). Enter the DNS entry provided by your ISP. If your ISP

has not provided the DNS IP address, contact your ISP to get that information or go to its website for

the information.

6. Click the OK button in the TCP/IP properties window, and click Close or the OK button for the Network

window.

7. Restart the computer when asked.

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-G Broadband Router with SpeedBooster

• For Windows 2000:

1. Click Start, Settings, and Control Panel. Double-click Network and Dial-Up Connections.

2. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and

select the Properties option.

3. In the Components checked are used by this connection box, highlight Internet Protocol (TCP/IP),

and click the Properties button. Select Use the following IP address option.

4. Enter a unique IP address that is not used by any other computer on the network connected to the

Router.

5. Enter the Subnet Mask, 255.255.255.0.

6. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).

7. Toward the bottom of the window, select Use the following DNS server addresses, and enter the

Preferred DNS server and Alternative DNS server (provided by your ISP). Contact your ISP or go on its

website to find the information.

8. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the

Local Area Connection Properties window.

9. Restart the computer if asked.

• For Windows XP:

The following instructions assume you are running Windows XP with the default interface. If you are using

the Classic interface (where the icons and menus look like previous Windows versions), please follow the

instructions for Windows 2000.

1. Click Start and Control Panel.

2. Click the Network and Internet Connections icon and then the Network Connections icon.

3. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using,

and select the Properties option.

4. In the This connection uses the following items box, highlight Internet Protocol (TCP/IP). Click the

Properties button.

5. Enter a unique IP address that is not used by any other computer on the network connected to the

Router.

6. Enter the Subnet Mask, 255.255.255.0.

7. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).

8. Toward the bottom of the window, select Use the following DNS server addresses, and enter the

Preferred DNS server and Alternative DNS server (provided by your ISP). Contact your ISP or go on its

website to find the information.

9. Click the OK button in the Internet Protocol (TCP/IP) Properties window. Click the OK button in the

Local Area Connection Properties window.

3. I want to test my Internet connection.

A Check your TCP/IP settings.

For Windows 98SE, Me, 2000, and XP:

• Make sure Obtain IP address automatically is selected in the settings.

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-G Broadband Router with SpeedBooster

B Open a command prompt.

For Windows 98SE and Me:

• Click Start and Run. In the Open field, type command. Press the Enter key or click the OK button.

For Windows 2000 and XP:

• Click Start and Run. In the Open field, type cmd. Press the Enter key or click the OK button. In the

command prompt, type ping 192.168.1.1 and press the Enter key.

• If you get a reply, the computer is communicating with the Router.

• If you do NOT get a reply, please check the cable, and make sure Obtain an IP address automatically is

selected in the TCP/IP settings for your Ethernet adapter.

C In the command prompt, type ping followed by your Internet or WAN IP address and press the Enter key.

The Internet or WAN IP Address can be found on the Status screen of the Router’s web-based utility. For

example, if your Internet or WAN IP address is 1.2.3.4, you would enter ping 1.2.3.4 and press the Enter key.

• If you get a reply, the computer is connected to the Router.

• If you do NOT get a reply, try the ping command from a different computer to verify that your original

computer is not the cause of the problem.

D In the command prompt, type ping www.yahoo.com and press the Enter key.

• If you get a reply, the computer is connected to the Internet. If you cannot open a webpage, try the ping

command from a different computer to verify that your original computer is not the cause of the problem.

• If you do NOT get a reply, there may be a problem with the connection. Try the ping command from a

different computer to verify that your original computer is not the cause of the problem.

5. I am not getting an IP address on the Internet with my Internet connection.

• Refer to “Problem #3, I want to test my Internet connection” to verify that you have connectivity.

• If you need to register the MAC address of your Ethernet adapter with your ISP, please see “Appendix E:

Finding the MAC address and IP Address for Your Ethernet Adapter.” If you need to clone the MAC address

of your Ethernet adapter onto the Router, see the System section of “Chapter 5: Configuring the

Wireless-G Broadband Router” for details.

• Make sure you are using the right Internet connection settings. Contact your ISP to see if your Internet

connection type is DHCP, Static IP Address, or PPPoE (commonly used by DSL consumers). Please refer to

the Setup section of “Chapter 5: Configuring the Wireless-G Broadband Router” for details on Internet

connection settings.

• Make sure you have the right cable. Check to see if the Internet column has a solidly lit Link/Act LED.

• Make sure the cable connecting from your cable or DSL modem is connected to the Router’s Internet port.

Verify that the Status page of the Router’s web-based utility shows a valid IP address from your ISP.

• Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds, and then turn on the Router,

cable/DSL modem, and computer. Check the Status tab of the Router’s web-based utility to see if you get

an IP address.

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-G Broadband Router with SpeedBooster

6. I am not able to access the Setup page of the Router’s web-based utility.

• Refer to “Problem #3, I want to test my Internet connection” to verify that your computer is properly

connected to the Router.

• Refer to “Appendix E: Finding the MAC Address and IP address for Your Ethernet Adapter” to verify that

your computer has an IP Address, Subnet Mask, Gateway, and DNS.

• Set a static IP address on your system; refer to “Problem #2: I need to set a static IP address.”

• Refer to “Problem #11: I need to remove the proxy settings or the dial-up pop-up window (for PPPoE

users).”

7. I need to set up a server behind my Router and make it available to the public.

To use a server like a web, ftp, or mail server, you need to know the respective port numbers they are using.

For example, port 80 (HTTP) is used for web; port 21 (FTP) is used for FTP, and port 25 (SMTP outgoing) and

port 110 (POP3 incoming) are used for the mail server. You can get more information by viewing the

documentation provided with the server you installed.

Follow these steps to set up port forwarding through the Router’s web-based utility. We will be setting up

web, ftp, and mail servers.

1. Access the Router’s web-based utility by going to http://192.168.1.1 or the IP address of the Router.

Go to the Applications & Gaming => Port Forwarding tab.

2. Enter any name you want to use for the Customized Application.

3. Enter the External Port range of the service you are using. For example, if you have a web server, you

would enter the range 80 to 80.

4. Check the protocol you will be using, TCP and/or UDP.

5. Enter the IP address of the PC or network device that you want the port server to go to. For example,

if the web server’s Ethernet adapter IP address is 192.168.1.100, you would enter 100 in the field

provided. Check “Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter” for

details on getting an IP address.

6. Check the Enable option for the port services you want to use. Consider the example below:

When you have completed the configuration, click the Save Settings button.

Application Start and End Protocol IP Address Enabled

Web server 80 to 80 Both 192.168.1.100 X

FTP server 21 to 21 TCP 192.168.1.101 X

SMTP (outgoing) 25 to 25 Both 192.168.1.102 X

POP3 (incoming) 110 to 110 Both 192.168.1.102 X

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-G Broadband Router with SpeedBooster

8. I need to set up online game hosting or use other Internet applications.

If you want to play online games or use Internet applications, most will work without doing any port

forwarding or DMZ hosting. There may be cases when you want to host an online game or Internet

application. This would require you to set up the Router to deliver incoming packets or data to a specific

computer. This also applies to the Internet applications you are using. The best way to get the information on

what port services to use is to go to the website of the online game or application you want to use. Follow

these steps to set up online game hosting or use a certain Internet application:

1. Access the Router’s web interface by going to http://192.168.1.1 or the IP address of the Router. Go to

the Applications & Gaming => Port Forwarding tab.

2. Enter any name you want to use for the Customized Application.

3. Enter the External Port range of the service you are using. For example, if you want to host Unreal

Tournament (UT), you would enter the range 7777 to 27900.

4. Check the protocol you will be using, TCP and/or UDP.

5. Enter the IP address of the PC or network device that you want the port server to go to. For example,

if the web server’s Ethernet adapter IP address is 192.168.1.100, you would enter 100 in the field

provided. Check “Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter” for

details on getting an IP address.

6. Check the Enable option for the port services you want to use. Consider the example below:

When you have completed the configuration, click the Save Settings button.

9. I can’t get the Internet game, server, or application to work.

If you are having difficulties getting any Internet game, server, or application to function properly, consider

exposing one PC to the Internet using DeMilitarized Zone (DMZ) hosting. This option is available when an

application requires too many ports or when you are not sure which port services to use. Make sure you

disable all the forwarding entries if you want to successfully use DMZ hosting, since forwarding has priority

over DMZ hosting. (In other words, data that enters the Router will be checked first by the forwarding settings.

If the port number that the data enters from does not have port forwarding, then the Router will send the data

to whichever PC or network device you set for DMZ hosting.)

Application Start and End Protocol IP Address Enabled

UT 7777 to 27900 Both 192.168.1.100 X

Halflife 27015 to 27015 Both 192.168.1.105 X

PC Anywhere 5631 to 5631 UDP 192.168.1.102 X

VPN IPSEC 500 to 500 UDP 192.168.1.100 X

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-G Broadband Router with SpeedBooster

Follow these steps to set DMZ hosting:

1. Access the Router’s web-based utility by going to http://192.168.1.1 or the IP address of the Router.

Go to the Applications & Gaming => Port Forwarding tab.

2. Disable or remove the entries you have entered for forwarding. Keep this information in case you

want to use it at a later time.

3. Go to the Applications & Gaming => DMZ tab.

4. Select Enable next to DMZ. In the DMZ Host IP Address field, enter the IP address of the computer you

want exposed to the Internet. This will bypass the NAT technology for that computer. Please refer to

“Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter” for details on getting

an IP address.

5. Once completed with the configuration, click the Save Settings button.

10.I forgot my password, or the password prompt always appears when I am saving settings to the

Router.

Reset the Router to factory default by pressing the Reset button for 10 seconds and then releasing it. If you

are still getting prompted for a password when saving settings, then perform the following steps:

1. Access the Router’s web-based utility by going to http://192.168.1.1 or the IP address of the Router.

Enter the default password admin, and click the Administrations => Management tab.

2. Enter a different password in the Router Password field, and enter the same password in the second

field to confirm the password.

3. Click the Save Settings button.

11.I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-up window.

If you have proxy settings, you need to disable these on your computer. Because the Router is the gateway for

the Internet connection, the computer does not need any proxy settings to gain access. Please follow these

directions to verify that you do not have any proxy settings and that the browser you use is set to connect

directly to the LAN.

• For Microsoft Internet Explorer 5.0 or higher:

1. Click Start, Settings, and Control Panel. Double-click Internet Options.

2. Click the Connections tab.

3. Click the LAN settings button and remove anything that is checked.

4. Click the OK button to go back to the previous screen.

5. Click the option Never dial a connection. This will remove any dial-up pop-ups for PPPoE users.

• For Netscape 4.7 or higher:

1. Start Netscape Navigator, and click Edit, Preferences, Advanced, and Proxies.

2. Make sure you have Direct connection to the Internet selected on this screen.

3. Close all the windows to finish.

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-G Broadband Router with SpeedBooster

12.To start over, I need to set the Router to factory default.

Hold the Reset button for 10 seconds and then release it. This will return the password, forwarding, and other

settings on the Router to the factory default settings. In other words, the Router will revert to its original

factory configuration.

13.My power LED will not stop flashing.

Press and hold the reset button for five seconds. If this does not work, your firmware may be corrupted. To

upgrade the firmware, follow the steps in “Appendix C: Upgrading Firmware.”

14.I need to upgrade the firmware.

In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download

the latest firmware at www.linksys.eu or linksys.com/international.

Follow these steps:

1. Go to the Linksys website at http://www.linksys.eu or linksys.com/international and download the

latest firmware.

2. To upgrade the firmware, follow the steps in “Appendix C: Upgrading Firmware.”

15.The firmware upgrade failed, and/or the Power LED is flashing.

The upgrade could have failed for a number of reasons. Follow these steps to upgrade the firmware and/or

make the Power LED stop flashing:

• If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open

the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s

instructions.

• Set a static IP address on the PC; refer to “Problem #2, I need to set a static IP address.” Use the following

IP address settings for the computer you are using:

IP Address: 192.168.1.50

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

• Perform the upgrade using the TFTP program or the Administration tab of the Router’s web-based utility.

16.My DSL service’s PPPoE is always disconnecting.

PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a

period of inactivity, just like a normal phone dial-up connection to the Internet.

• There is a setup option to “keep alive” the connection. This may not always work, so you may need to re-

establish connection periodically.

1. To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the

Router.

2. Enter the password, if asked. (The default password is admin.)

3. On the Setup screen, select the option Keep Alive, and set the Redial Period option at 20 (seconds).

4. Click the Save Settings button.

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-G Broadband Router with SpeedBooster

5. Click the Status tab, and click the Connect button.

6. You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you

see the login status display as Connected.

• Click the Save Settings button to continue.

• If the connection is lost again, follow steps 1- 6 to re-establish connection.

17.I can’t access my e-mail, web or I am getting corrupted data from the Internet.

The Maximum Transmission Unit (MTU) setting may need to be adjusted. By default, the MTU is set at 1500.

For most DSL users, it is strongly recommended to use MTU 1492.

• If you are having some difficulties, perform the following steps:

1. To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the

Router.

2. Enter the password, if asked. (The default password is admin.)

3. Look for the MTU option, and select Manual. In the Size field, enter 1492.

4. Click the Save Settings button to continue.

• If your difficulties continue, change the Size to different values. Try this list of values, one value at a time,

in this order, until your problem is solved:

1462

1400

1362

1300

18.When I enter a URL or IP address, I get a time-out error or am prompted to retry.

• Check if other PCs work. If they do, ensure that your workstation’s IP settings are correct (IP Address,

Subnet Mask, Default Gateway, and DNS). Restart the computer that is having a problem.

• If the PCs are configured correctly, but still not working, check the Router. Ensure that it is connected and

powered on. Connect to it and check its settings. (If you cannot connect to it, check the LAN and power

connections.)

• If the Router is configured correctly, check your Internet connection (DSL/cable modem, etc.) to see if it is

working correctly. You can remove the Router to verify a direct connection.

• Manually configure the TCP/IP settings with a DNS address provided by your ISP.

• Make sure that your browser is set to connect directly and that any dial-up is disabled. For Internet

Explorer, click Tools, Internet Options, and then the Connection tab. Make sure that Internet Explorer is

set to Never dial a connection. For Netscape Navigator, click Edit, Preferences, Advanced, and Proxy.

Make sure that Netscape Navigator is set to Direct connection to the Internet.

19.I cannot connect to the Internet.

• For Cable users - Click on the Status tab and make sure you have the Internet IP address is not 0.0.0.0. If

it is, click the DHCP Renew button, and wait a few minutes for the router to try and contact your service

provider. After the router successfully obtains an IP address, restart your computer.

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-G Broadband Router with SpeedBooster

• For DSL users - 1) Make sure you have typed in your user name and password correctly. Some service

providers use your full e-mail address as the user name. If you are sure you have enter the right user

name, try using username@[isp.com], where isp.com is the name of your service provider. 2) Power down

your DSL Modem, your PC, and your router. Then power on your DSL Modem, wait for the LEDs on the DSL

modem to stop flashing. Power on your router and wait for the power LED to stop flashing. Finally, power

on your PC.

20.My wireless-G speed seems to be slow.

• Reposition the antenna.

• Reposition the router so that it's higher up, above your other networking gear.

• Change CTS Protection to Disable under advanced wireless settings.

21.I do not see a speed improvement while surfing wirelessly with my SpeedBooster equipment.

• Your Internet connection is usually much slower than your wireless network with SpeedBooster

equipment. This equipment will not affect the speed of your Internet connection.

• You will see the most improvements in transferring or streaming files from one computer to another in

your network.

• Your network speed will slow down if you have mixed 802.11g and SpeedBooster clients. For maximum

performance, use all SpeedBooster devices on your network.

22.How do I turn on SpeedBooster on my router?

SpeedBooster is automatically turned on in Mixed and G-Only Mode. There's nothing you need to do to utilize

this feature, but your client adapter must also have SpeedBooster to utilize it.

Appendix A: Troubleshooting

Frequently Asked Questions

Wireless-G Broadband Router with SpeedBooster

Frequently Asked Questions

After using SecureEasySetup, my existing wireless devices can no longer connect to the Router.

SecureEasySetup uses WPA-Personal encryption. If your current wireless devices do not support WPA-Personal

security, then you cannot use SecureEasySetup on your network. You will need to manually configure your

network security using the encryption supported by your existing devices.

How do I set up additional devices using SecureEasySetup?

Repeat the SecureEasySetup process for each device until all of your devices have been configured.

Where is my SecureEasySetup button?

On the Router, the SecureEasySetup button is located on the front panel. The button should be lighted either

orange or white. For other SecureEasySetup devices, refer to each wireless device's documentation to locate the

button on that device.

I have devices that support WPA-Personal security, but do not have SecureEasySetup. Can I still use

SecureEasySetup?

Yes. Print out the wireless security settings at the end of the SecureEasySetup process, and then manually

configure the settings for your non-SecureEasySetup devices. Refer to each wireless device’s documentation for

instructions on how to enter these settings.

What is the maximum number of IP addresses that the Router will support?

The Router will support up to 253 IP addresses.

Is IPSec Pass-Through supported by the Router?

Yes, it is a built-in feature that the Router automatically enables.

Where is the Router installed on the network?

In a typical environment, the Router is installed between the cable/DSL modem and the LAN. Plug the Router into

the cable/DSL modem’s Ethernet port.

Does the Router support IPX or AppleTalk?

No. TCP/IP is the only protocol standard for the Internet and has become the global standard for communications.

IPX, a NetWare communications protocol used only to route messages from one node to another, and AppleTalk, a

communications protocol used on Apple and Macintosh networks, can be used for LAN to LAN connections, but

those protocols cannot connect from the Internet to a LAN.

Appendix A: Troubleshooting

Frequently Asked Questions

Wireless-G Broadband Router with SpeedBooster

Does the Internet connection of the Router support 100Mbps Ethernet?

The Router’s current hardware design supports up to 100Mbps Ethernet on its Internet port; however, the Internet

connection speed will vary depending on the speed of your broadband connection. The Router also supports

100Mbps over the auto-sensing Fast Ethernet 10/100 switch on the LAN side of the Router.

What is Network Address Translation and what is it used for?

Network Address Translation (NAT) translates multiple IP addresses on the private LAN to one public address that

is sent out to the Internet. This adds a level of security since the address of a PC connected to the private LAN is

never transmitted on the Internet. Furthermore, NAT allows the Router to be used with low cost Internet accounts,

such as DSL or cable modems, when only one TCP/IP address is provided by the ISP. The user may have many

private addresses behind this single address provided by the ISP.

Does the Router support any operating system other than Windows 98SE, Windows Millennium,

Windows 2000, or Windows XP?

Yes, but Linksys does not, at this time, provide technical support for setup, configuration or troubleshooting of

any non-Windows operating systems.

Does the Router support ICQ send file?

Yes, with the following fix: click ICQ menu -> preference -> connections tab->, and check I am behind a firewall

or proxy. Then set the firewall time-out to 80 seconds in the firewall setting. The Internet user can then send a file

to a user behind the Router.

I set up an Unreal Tournament Server, but others on the LAN cannot join. What do I need to do?

If you have a dedicated Unreal Tournament server running, you need to create a static IP for each of the LAN

computers and forward ports 7777, 7778, 7779, 7780, 7781, and 27900 to the IP address of the server. You can

also use a port forwarding range of 7777 ~ 27900. If you want to use the UT Server Admin, forward another port.

(Port 8080 usually works well but is used for remote admin. You may have to disable this.) Then in the

[UWeb.WebServer] section of the server.ini file, set the ListenPort to 8080 (to match the mapped port above) and

ServerName to the IP assigned to the Router from your ISP.

Can multiple gamers on the LAN get on one game server and play simultaneously with just one public IP

address?

It depends on which network game or what kind of game server you are using. For example, Unreal Tournament

supports multi-login with one public IP.

How do I get Half-Life: Team Fortress to work with the Router?

The default client port for Half-Life is 27005. The computers on your LAN need to have “+clientport 2700x”

added to the HL shortcut command line; the x would be 6, 7, 8, and on up. This lets multiple computers connect

to the same server. One problem: Version 1.0.1.6 won’t let multiple computers with the same CD key connect at

Appendix A: Troubleshooting

Frequently Asked Questions

Wireless-G Broadband Router with SpeedBooster

the same time, even if on the same LAN (not a problem with 1.0.1.3). As far as hosting games, the HL server does

not need to be in the DMZ. Just forward port 27015 to the local IP address of the server computer.

How can I block corrupted FTP downloads?

If you are experiencing corrupted files when you download a file with your FTP client, try using another FTP

program.

The web page hangs; downloads are corrupt, or nothing but junk characters are being displayed on the

screen. What do I need to do?

Force your Ethernet adapter to 10Mbps or half duplex mode, and turn off the “Auto-negotiate” feature of your

Ethernet adapter as a temporary measure. (Please look at the Network Control Panel in your Ethernet adapter’s

Advanced Properties tab.) Make sure that your proxy setting is disabled in the browser. Check our website at

www.linksys.eu or linksys.com/international for more information.

If all else fails in the installation, what can I do?

Reset the Router by holding down the reset button until the Power LED fully turns on and off. Reset your cable or

DSL modem by powering the unit off and then on. Obtain and flash the latest firmware release that is readily

available on the Linksys website, www.linksys.eu or linksys.com/international.

How will I be notified of new Router firmware upgrades?

All Linksys firmware upgrades are posted on the Linksys website at www.linksys.eu or linksys.com/international,

where they can be downloaded for free. To upgrade the Router’s firmware, use the System tab of the Router’s

web-based utility. If the Router’s Internet connection is working well, there is no need to download a newer

firmware version, unless that version contains new features that you would like to use. Downloading a more

current version of Router firmware will not enhance the quality or speed of your Internet connection, and may

disrupt your current connection stability.

Will the Router function in a Macintosh environment?

Yes, but the Router’s setup pages are accessible only through Internet Explorer 4.0 or Netscape Navigator 4.0 or

higher for Macintosh.

I am not able to get the web configuration screen for the Router. What can I do?

You may have to remove the proxy settings on your Internet browser, e.g., Netscape Navigator or Internet

Explorer. Or remove the dial-up settings on your browser. Check with your browser documentation, and make

sure that your browser is set to connect directly and that any dial-up is disabled. Make sure that your browser is

set to connect directly and that any dial-up is disabled. For Internet Explorer, click Tools, Internet Options, and

then the Connection tab. Make sure that Internet Explorer is set to Never dial a connection. For Netscape

Navigator, click Edit, Preferences, Advanced, and Proxy. Make sure that Netscape Navigator is set to Direct

connection to the Internet.

Appendix A: Troubleshooting

Frequently Asked Questions

Wireless-G Broadband Router with SpeedBooster

What is DMZ Hosting?

Demilitarized Zone (DMZ) allows one IP address (computer) to be exposed to the Internet. Some applications

require multiple TCP/IP ports to be open. It is recommended that you set your computer with a static IP if you

want to use DMZ Hosting. To get the LAN IP address, see “Appendix E: Finding the MAC Address and IP Address

for Your Ethernet Adapter.”

If DMZ Hosting is used, does the exposed user share the public IP with the Router?

No.

Does the Router pass PPTP packets or actively route PPTP sessions?

The Router allows PPTP packets to pass through.

Is the Router cross-platform compatible?

Any platform that supports Ethernet and TCP/IP is compatible with the Router.

How many ports can be simultaneously forwarded?

Theoretically, the Router can establish 520 sessions at the same time, but you can only forward 10 ranges of

ports.

What are the advanced features of the Router?

The Router’s advanced features include Advanced Wireless settings, Filters, Port Forwarding, Routing, and DDNS.

How do I get mIRC to work with the Router?

Under the Port Forwarding tab, set port forwarding to 113 for the PC on which you are using mIRC.

Can the Router act as my DHCP server?

Yes. The Router has DHCP server software built-in.

Can I run an application from a remote computer over the wireless network?

This will depend on whether or not the application is designed to be used over a network. Consult the

application’s documentation to determine if it supports operation over a network.

What is the IEEE 802.11g standard?

It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware

from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard.

The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz.

Appendix A: Troubleshooting

Frequently Asked Questions

Wireless-G Broadband Router with SpeedBooster

What IEEE 802.11b features are supported?

The product supports the following IEEE 802.11b functions:

• CSMA/CA plus Acknowledge protocol

• Multi-Channel Roaming

• Automatic Rate Selection

• RTS/CTS feature

• Fragmentation

• Power Management

What is ad-hoc mode?

When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to

communicate directly with each other. The ad-hoc wireless network will not communicate with any wired

network.

What is infrastructure mode?

When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with a

wired network through a wireless access point.

What is roaming?

Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout

an area greater than that covered by a single access point. Before using the roaming function, the workstation

must make sure that it is the same channel number with the access point of dedicated coverage area.

To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions. Each

node and access point, for example, must always acknowledge receipt of each message. Each node must

maintain contact with the wireless network even when not actually transmitting data. Achieving these functions

simultaneously requires a dynamic RF networking technology that links access points and nodes. In such a

system, the user’s end node undertakes a search for the best possible access to the system. First, it evaluates

such factors as signal strength and quality, as well as the message load currently being carried by each access

point and the distance of each access point to the wired backbone. Based on that information, the node next

selects the right access point and registers its address. Communications between end node and host computer

can then be transmitted up and down the backbone.

As the user moves on, the end node’s RF transmitter regularly checks the system to determine whether it is in

touch with the original access point or whether it should seek a new one. When a node no longer receives

acknowledgment from its original access point, it undertakes a new search. Upon finding a new access point, it

then re-registers, and the communication process continues.

Appendix A: Troubleshooting

Frequently Asked Questions

Wireless-G Broadband Router with SpeedBooster

What is ISM band?

The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM

(Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available

worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in

the hands of users around the globe.

What is Spread Spectrum?

Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in

reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for

reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband

transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that

the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to

the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives,

Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS).

What is DSSS? What is FHSS? And what are their differences?

Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that

is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical

channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-Sequence Spread-

Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip

(or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if

one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can

recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low

power wideband noise and is rejected (ignored) by most narrowband receivers.

What is WEP?

WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 64-bit or 128-bit shared key algorithm, as

described in the IEEE 802.11 standard.

What is a MAC Address?

The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any Ethernet

networking device, such as a network adapter, that allows the network to identify it at the hardware level. For all

practical purposes, this number is usually permanent. Unlike IP addresses, which can change every time a

computer logs onto the network, the MAC address of a device stays the same, making it a valuable identifier for

the network.

How do I reset the Router?

Press the Reset button on the back panel for about five seconds. This will reset the Router to its default settings.

Appendix A: Troubleshooting

Frequently Asked Questions

Wireless-G Broadband Router with SpeedBooster

How do I resolve issues with signal loss?

There is no way to know the exact range of your wireless network without testing. Every obstacle placed between

the Router and a wireless PC will create signal loss. Lead glass, metal, concrete floors, water and walls will

inhibit the signal and reduce range. Start with the Router and your wireless PC in the same room and move it

away in small increments to determine the maximum range in your environment.

You may also try using different channels, as this may eliminate interference affecting only one channel.

I have excellent signal strength, but I cannot see my network.

WEP is probably enabled on the Router, but not on your wireless adapter (or vice versa). Verify that the same WEP

keys and levels (64 or 128) are being used on all nodes of your wireless network.

How many channels/frequencies are available with the Router?

There are eleven available channels, ranging from 1 to 11 in most of North, Central, and South America). There

are thirteen available channeels, ranging from 1 to 13 in most of Asia, Africa, and Australia.

If your questions are not addressed here, refer to the Linksys website, www.linksys.eu or

linksys.com/international.

Appendix B: Wireless Security

Security Precautions

Wireless-G Broadband Router with SpeedBooster

Appendix B: Wireless Security

Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of

Linksys products provide several network security features, but they require specific action on your part for

implementation. So, keep the following in mind whenever you are setting up or using your wireless network.

Security Precautions

The following is a complete list of security precautions to take (at least steps 1 through 5 should be followed):

1. Change the default SSID.

2. Disable SSID Broadcast.

3. Change the default password for the Administrator account.

4. Enable MAC Address Filtering.

5. Change the SSID periodically.

6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce

your network performance.

7. Change the WEP encryption keys periodically.

For information on implementing these security features, refer to “Chapter 5: Configuring the Wireless-G

Broadband Router.”

Security Threats Facing Wireless Networks

Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking

products first listen for “beacon messages”. These messages can be easily decrypted and contain much of the

network’s information, such as the network’s SSID (Service Set Identifier). Here are the steps you can take:

Change the administrator’s password regularly. With every wireless networking device you use, keep in mind

that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only

person who can change network settings. If a hacker gets a hold of the administrator’s password, he, too, can

change those settings. So, make it harder for a hacker to get that information. Change the administrator’s

password regularly.

NOTE: Some of these security features are

available only through the network router or

access point. Refer to the router or access

point’s documentation for more information.

Appendix B: Wireless Security

Security Threats Facing Wireless Networks

Wireless-G Broadband Router with SpeedBooster

SSID. There are several things to keep in mind about the SSID:

1. Disable Broadcast

2. Make it unique

3. Change it often

Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be

more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast

the SSID.

Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.)

Hackers know these defaults and can check these against your network. Change your SSID to something unique

and not something related to your company or the networking products you use.

Change your SSID regularly so that any hackers who have gained access to your wireless network will have to

start from the beginning in trying to break in.

MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only

those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with

a random MAC Address.

WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security

concerns. This is overstating WEP’s ability. Again, this can only provide enough security to make a hacker’s job

more difficult.

There are several ways that WEP can be maximized:

1. Use the highest level of encryption possible

2. Use “Shared Key” authentication

3. Change your WEP key regularly

WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. WPA is stronger

than WEP encryption, and WPA2 has stronger encryption than WPA. WPA and WPA2 give you a choice of two

encryption methods: TKIP (Temporal Key Integrity Protocol), which incorporates Message Integrity Code (MIC) to

provide protection against hackers, and AES (Advanced Encryption System), which utilizes a symmetric 128-Bit

block data encryption. (AES is stronger than TKIP.)

IMPORTANT: Always remember that each

device in your wireless network MUST use

the same encryption method and encryption

key or your wireless network will not function

properly.

Appendix B: Wireless Security

Security Threats Facing Wireless Networks

Wireless-G Broadband Router with SpeedBooster

WPA-Enterprise and WPA2-Enterprise use a RADIUS (Remote Authentication Dial-In User Service) server for

authentication. RADIUS uses a RADIUS server and WEP encryption.

WPA/WPA2-Personal. Select the type of algorithm, TKIP or AES, and enter a password in the WPA Shared

Key field of 8-63 characters. Enter a Key Renewal period time between 0 and 99,999 seconds, which instructs

the Router or other device how often it should change the encryption keys.

WPA/WPA2-Enterprise. This method is WPA or WPA2 used in coordination with a RADIUS server. Enter the IP

address and port number of the RADIUS server. Then enter the key shared between the Router and its RADIUS

server. Then enter a Key Renewal period, which instructs the Router or other device how often it should

change the encryption keys.

RADIUS. This method is WEP used in coordination with a RADIUS server. Enter the IP address and port number of

the RADIUS server. Then enter the key shared between the Router and its RADIUS server. Enter the WEP settings.

Implementing encryption may have a negative impact on your network’s performance, but if you are transmitting

sensitive data over your network, encryption should be used.

These security recommendations should help keep your mind at ease while you are enjoying the most flexible

and convenient technology Linksys has to offer.

The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance

can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance

depends on many factors, conditions and variables, including distance from the access point, volume of network

traffic, building materials and construction, operating system used, mix of wireless products used, interference

and other adverse conditions.

Appendix C: Upgrading Firmware

Wireless-G Broadband Router with SpeedBooster

Appendix C: Upgrading Firmware

The Broadband Router's firmware is upgraded through the Web-based Utility's Administration tab. Follow these

instructions:

1. Download the firmware from Linksys's website at www.linksys.eu or linksys.com/international.

2. Click Firmware Upgrade from the Web-Utility's Administration tab, and the Firmware Upgrade screen will

appear.

3. Enter the location of the firmware's file or click the Browse button to find the file.

4. Then, click the Upgrade button to upgrade the firmware.

Figure C-1: Upgrade Firmware

Appendix D: Windows Help

Wireless-G Broadband Router with SpeedBooster

Appendix D: Windows Help

Almost all Linksys wireless products require Microsoft Windows. Windows is the most used operating system in

the world and comes with many features that help make networking easier. These features can be accessed

through Windows Help and are described in this appendix.

TCP/IP

Before a computer can communicate with the Broadband Router, TCP/IP must be enabled. TCP/IP is a set of

instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks as well.

Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help provides

complete instructions on enabling TCP/IP.

Shared Resources

If you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on

utilizing shared resources.

Network Neighborhood/My Network Places

Other PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the

version of Windows you're running). Windows Help provides complete instructions on adding PCs to your

network.

Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter

Windows 98SE or Me Instructions

Wireless-G Broadband Router with SpeedBooster

Appendix E: Finding the MAC Address and IP Address for Your

Ethernet Adapter

This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC

filtering and/or MAC address cloning feature of the Router. You can also find the IP address of your computer’s

Ethernet adapter. This IP address is used for the Router’s filtering, forwarding, and/or DMZ features. Follow the

steps in this appendix to find the adapter’s MAC or IP address in Windows 98, Me, 2000, or XP.

Windows 98SE or Me Instructions

1. Click Start and Run. In the Open field, enter winipcfg. Then press the Enter key or the OK button.

2. When the IP Configuration screen appears, select the Ethernet adapter you have connected to the Router via a

CAT 5 Ethernet network cable.

3. Write down the Adapter Address as shown on your computer screen. This is the MAC address for your

Ethernet adapter and is shown as a series of numbers and letters.

The MAC address/Adapter Address is what you will use for MAC address cloning or MAC filtering.

Another screen will show the Ethernet adapter’s IP address. (Shown in the example as 192.168.1.100.) Your

computer may show something different.

Windows 2000 or XP Instructions

1. Click Start and Run. In the Open field, enter cmd. Press the Enter key or click the OK button.

2. At the command prompt, enter ipconfig /all. Then press the Enter key.

Figure E-2: MAC Address/Adapter Address

Figure E-1: IP Configuration Screen

NOTE: The MAC address is also called the Adapter Address.

Figure E-3: MAC Address/Physical Address

Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter

For the Router’s Web-based Utility

Wireless-G Broadband Router with SpeedBooster

3. Write down the Physical Address as shown on your computer screen; it is the MAC address for your Ethernet

adapter. This appears as a series of numbers and letters.

The MAC address/Physical Address is what you will use for MAC address cloning or MAC filtering.

Another screen will show the Ethernet adapter’s IP address. (Shown in the example as 192.168.1.100.) Your

computer may show something different.

For the Router’s Web-based Utility

For MAC filtering, enter the 12-digit MAC address in this format, XXXXXXXXXXXX, WITHOUT the hyphens.

For MAC address cloning, enter the 12-digit MAC address in the MAC Address fields provided, two digits per field.

Figure E-4: MAC Address Filter List

NOTE: The MAC address is also called the Physical Address.

Figure E-5: MAC Address Clone

Appendix F: Glossary

Wireless-G Broadband Router with SpeedBooster

Appendix F: Glossary

This glossary contains some basic networking terms you may come across when using this product. For more

advanced terms, see the complete Linksys glossary at http://www.linksys.com/glossary.

Access Point - A device that allows wireless-equipped computers and other devices to communicate with a

wired network. Also used to expand the range of a wireless network.

Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of

an access point.

AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption.

Bandwidth - The transmission capacity of a given device or network.

Bit - A binary digit.

Boot - To start a device and cause it to start executing instructions.

Broadband - An always-on, fast Internet connection.

Browser - An application program that provides a way to look at and interact with all the information on the

World Wide Web.

Byte - A unit of data that is usually eight bits long

Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the

Internet.

Daisy Chain - A method used to connect devices in a series, one after the other.

DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a

fixed domain name (e.g., www.xyz.com) and a dynamic IP address.

Default Gateway - A device that forwards Internet traffic from your local area network.

DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign

temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time,

instead of assigning permanent IP addresses.

Appendix F: Glossary

Wireless-G Broadband Router with SpeedBooster

DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be “seen” from

the Internet.

DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP

addresses.

Domain - A specific name for a network of computers.

Download - To receive a file transmitted over a network.

DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.

Dynamic IP Address - A temporary IP address assigned by a DHCP server.

EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access.

Many specific authentication methods work within this framework.

Encryption - Encoding data transmitted in a network.

Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common

transmission medium.

Firewall - A set of related programs located at a network gateway server that protects the resources of a

network from users from other networks.

Firmware - The programming code that runs a networking device.

FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network.

Full Duplex - The ability of a networking device to receive and transmit data simultaneously.

Gateway - A device that interconnects networks with different, incompatible communications protocols.

Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a

time.

HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World

Wide Web.

Infrastructure - A wireless network that is bridged to a wired network via an access point.

IP (Internet Protocol) - A protocol used to send data over a network.

Appendix F: Glossary

Wireless-G Broadband Router with SpeedBooster

IP Address - The address used to identify a computer or device on a network.

IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device.

IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer.

ISP (Internet Service Provider) - A company that provides access to the Internet.

LAN (Local Area Network) - The computers and networking products that make up your local network.

MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking

device.

Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.

NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different

IP address for the Internet.

Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or

transmission between users.

Packet - A unit of data sent over a network.

Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically

generating the WEP encryption keys for Linksys products.

Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.

POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet.

Port - The connection point on a computer or networking device used for plugging in cables or adapters.

Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.

PPPoE (Point to P

oint Protocol over Ethernet) - A type of broadband connection that provides authentication

(username and password) in addition to data transport.

PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be

tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe.

RADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control

network access.

Appendix F: Glossary

Wireless-G Broadband Router with SpeedBooster

RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires.

Roaming - The ability to take a wireless device from one access point's range to another without losing the

connection.

Router - A networking device that connects multiple networks together.

Server - Any computer whose function in a network is to provide user access to files, printing, communications,

and other services.

SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet.

SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol.

SPI (Stateful Packet Inspection) Firewall - A technology that inspects incoming packets of information before

allowing them to enter the network.

SSID (Service Set IDentifier) - Your wireless network's name.

Static IP Address - A fixed address assigned to a computer or device that is connected to a network.

Static Routing - Forwarding data in a network via a fixed path.

Subnet Mask - An address code that determines the size of the network.

Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of

devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an

electrical circuit.

TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement

from the recipient of data sent.

TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a

network.

Telnet - A user command and TCP/IP protocol used for accessing remote PCs.

TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password

capability.

Throughput - The amount of data moved successfully from one node to another in a given time period.

Appendix F: Glossary

Wireless-G Broadband Router with SpeedBooster

TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for

each packet transmitted.

Topology - The physical layout of a network.

TX Rate - Transmission Rate.

Upgrade - To replace existing software or firmware with a newer version.

Upload - To transmit a file over a network.

URL (Uniform Resource Locator) - The address of a file located on the Internet.

VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another

over the Internet.

WAN (Wide Area Network)- The Internet.

WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for

greater security.

WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with

each other wirelessly.

WPA (Wi-Fi Protected Access) - A wireless security protocol using TKIP (Temporal Key Integrity Protocol)

encryption, which can be used in conjunction with a RADIUS server.

Appendix G: Specifications

Wireless-G Broadband Router with SpeedBooster

Appendix G: Specifications

Model WRT54GS

Standards IEEE 802.3, IEEE 802.3u, IEEE 802.11g, IEEE 802.11b

Channels 11 Channels (most of North, South, and Central America)

13 Channels (most of Europe and Asia)

Ports Internet: One 10/100 RJ-45 Port

LAN: Four 10/100 RJ-45 Switched Ports

One Power Port

Buttons One Reset Button

One SecureEasySetup Button

Cabling Type CAT5

LEDs Power, DMZ, WLAN, LAN (1-4), Internet, SecureEasySetup

RF Power Output 18 dBm

UPnP able/cert Able

Security features Stateful Packet Inspection (SPI) Firewall, Internet Policy

Wireless Security Wi-Fi Protected Access™2 (WPA2), WEP, Wireless MAC

Filtering

Dimensions 186 mm x 48 mm x 154 mm

Unit Weight 385 g

Power External, 12V DC, 0.5A

Appendix G: Specifications

Wireless-G Broadband Router with SpeedBooster

Certification FCC, IC-03, CE, Wi-Fi (802.11b, 802.11g), WPA2, WMM

Operating Temp. 0° C to 40° C

Storage Temp. -20° C to 70° C

Operating Humidity 10% to 85% Non-Condensing

Storage Humidity 5% to 90% Non-Condensing

Appendix H: Warranty Information

Wireless-G Broadband Router with SpeedBooster

Appendix H: Warranty Information

Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially

free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under

this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates.

This limited warranty extends only to the original purchaser.

If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return

Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are

requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a

copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You

are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You

only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling

charges.

ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED

TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND

WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not

allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives

You specific legal rights, and You may also have other rights which vary by jurisdiction.

This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated,

repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical

or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for

intruding upon and attacking networks, Linksys does not warrant that the Product will be free of vulnerability to intrusion or

attack.

TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT,

OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF

LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT

(INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT

WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if

any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.

This Warranty is valid and may be processed only in the country of purchase.

Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

Appendix I: Regulatory Information

FCC Statement

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment or devices

• Connect the equipment to an outlet other than the receiver's

• Consult a dealer or an experienced radio/TV technician for assistance

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 20cm between the radiator and your body.

Safety Notices

Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.

Do not use this product near water, for example, in a wet basement or near a swimming pool.

Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Industry Canada (Canada)

This device complies with Industry Canada ICES-003 and RSS210 rules.

Cet appareil est conforme aux normes NMB003 et RSS210 d'Industrie Canada.

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

IC Statement

Operation is subject to the following two conditions:

1. This device may not cause interference and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Règlement d’Industry Canada

Le fonctionnement est soumis aux conditions suivantes :

1. Ce périphérique ne doit pas causer d'interférences;

2. Ce périphérique doit accepter toutes les interférences reçues, y compris celles qui risquent d'entraîner un

fonctionnement indésirable.

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

Compliance Information for 2,4-GHz and 5-GHz Wireless Products Relevant to the EU and Other Countries

Following the EU Directive 1999/5/EC (R&TTE Directive)

Declaration of Conformity with Regard to the EU Directive 1999/5/EC (R&TTE Directive)

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

The following standards were applied during the assessment of the product against the requirements of the Directive

1999/5/EC:

• Radio: EN 300 328 and/or EN 301 893 as applicable

• EMC: EN 301 489-1, EN 301 489-17

• Safety: EN 60950 and either EN 50385 or EN 50371

Dynamic Frequency Selection (DFS) and Transmit Power Control (TPC) are required for operation in the 5 GHz band.

DFS: The equipment meets the DFS requirements as defined in ETSI EN 301 893. This feature is required by the regulations

to avoid interference with Radio Location Services (radars).

TPC: For operation in the 5 GHz band, the maximum power level is 3 dB or more below the applicable limit. As such, TPC is

not required. Nevertheless, you can further reduce the power output if you wish to do so. For more information about

changing the power output settings, refer to your product’s documentation on its CD or www.linksys.eu or linksys.com/

international.

CE Marking

For the Linksys Wireless-N, -G, -B, and/or -A products, the following CE mark, notified body number (where applicable),

and class 2 identifier are added to the equipment.

Check the CE label on the product to find out which notified body was involved during the assessment.

NOTE: For all products, the Declaration of Conformity (DofC) is available through one or more of these options:

• A pdf file is included on the product's CD.

• A print copy is included with the product.

• A pdf file is available on the product's webpage. Visit www.linksys.eu or linksys.com/international and select your

country or region. Then select your product.

If you need any other technical documentation, see the “Technical Documents on www.linksys.eu or

linksys.com/international” section, as shown later in this appendix.

or oror

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

National Restrictions

This product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any

limitation except for the countries mentioned below:

Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans

aucune limitation, excepté pour les pays mentionnés ci-dessous:

Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttive EU 1999/5/EC) senza

nessuna limitazione, eccetto per i paesii menzionati di seguito:

Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden (sowie in anderen Staaten die der EU

Direktive 1999/5/CE folgen) mit Außnahme der folgenden aufgeführten Staaten:

In the majority of the EU and other European countries, the 2,4- and 5-GHz bands have been made available for the use of

wireless local area networks (LANs). Table 1 provides an overview of the regulatory requirements applicable for the

2,4- and 5-GHz bands.

Later in this document you will find an overview of countries in which additional restrictions or requirements or both are

applicable.

The requirements for any country may evolve. Linksys recommends that you check with the local authorities for the latest

status of their national regulations for both the 2,4- and 5-GHz wireless LANs.

† Dynamic Frequency Selection and Transmit Power Control are required in the frequency ranges of 5250-5350 MHz and

5470-5725 MHz.

Table 1: Overview of Regulatory Requirements for Wireless LANs

Frequency Band (MHz) Max Power Level

(EIRP) (mW)

Indoor

ONLY

Indoor &

Outdoor

2400-2483.5 100 X

5150-5350

†

200 X

5470-5725

†

1000 X

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

The following countries have restrictions and/or requirements in addition to those given in Table 1:

Denmark

In Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage.

I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs.

France

For 2,4 GHz, the output power is restricted to 10 mW eirp when the product is used outdoors in the band

2454 - 2483,5 MHz. There are no restrictions when used in other parts of the 2,4 GHz band. Check http://www.arcep.fr/ for

more details.

Pour la bande 2,4 GHz, la puissance est limitée à 10 mW en p.i.r.e. pour les équipements utilisés en extérieur dans la bande

2454 - 2483,5 MHz. Il n'y a pas de restrictions pour des utilisations dans d'autres parties de la bande 2,4 GHz. Consultez

http://www.arcep.fr/ pour de plus amples détails.

Italy

This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table

for Italy. Unless this 2,4-GHz wireless LAN product is operating within the boundaries of the owner’s property, its use

requires a “general authorization”. Please check http://www.comunicazioni.it/it/ for more details.

Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle

frequenze in Italia. Se non viene installato all’interno del proprio fondo, l’utilizzo di prodotti Wireless LAN a 2,4 GHz richiede

una “Autorizzazione Generale”. Consultare http://www.comunicazioni.it/it/ per maggiori dettagli.

Table 2: Applicable Power Levels in France

Location Frequency Range (MHz) Power (EIRP)

Indoor (No restrictions) 2400-2483.5 100 mW (20 dBm)

Outdoor 2400-2454

2454-2483.5

100 mW (20 dBm)

10 mW (10 dBm)

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

Latvia

The outdoor usage of the 2,4 GHz band requires an authorization from the Electronic Communications Office. Please check

http://www.esd.lv for more details.

Notes: (1) Although Norway, Switzerland and Liechtenstein are not EU member states, the EU Directive 1999/5/EC has also

been implemented in those countries.

(2) The regulatory limits for maximum output power are specified in eirp. The eirp level of a device can be calculated by

adding the gain of the antenna used (specified in dBi) to the output power available at the connector (specified in dBm).

Product Usage Restrictions

This product is designed for indoor usage only. Outdoor usage is not recommended, unless otherwise noted.

2,4 GHz Restrictions

This product is designed for use with the standard, integral or dedicated (external) antenna(s) that is/are shipped together

with the equipment. However, some applications may require the antenna(s), if removable, to be separated from the

product and installed remotely from the device by using extension cables. For these applications, Linksys offers an R-SMA

extension cable (AC9SMA) and an R-TNC extension cable (AC9TNC). Both of these cables are 9 meters long and have a

cable loss (attenuation) of 5 dB. To compensate for the attenuation, Linksys also offers higher gain antennas, the HGA7S

(with R-SMA connector) and HGA7T (with R-TNC connector). These antennas have a gain of 7 dBi and may only be used

with either the R-SMA or R-TNC extension cable.

Combinations of extension cables and antennas resulting in a radiated power level exceeding 100 mW EIRP are illegal.

Power Output of Your Device

To comply with your country’s regulations, you may have to change the power output of your wireless device. Proceed to

the appropriate section for your device.

NOTE: The power output setting may not be available on all wireless products. For more information, refer to the

documentation on your product’s CD or at http://www.linksys.eu or linksys.com/international.

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

Wireless Adapters

For wireless adapters operating in the 2,4-GHz band, the typical radiated output power is 18 dBm EIRP, while the maximum

radiated output power will not exceed 20 dBm (100 mW) EIRP. For wireless adapters operating in the 5-GHz band, the

typical radiated output power is 20 dBm EIRP, while the maximum radiated output power will not exceed 23 dBm (200 mW)

EIRP. If you need to alter your wireless adapter’s power output, follow the appropriate instructions for your computer’s

operating system:

Windows XP

1. Double-click the Wireless icon in your desktop’s system tray.

2. Open the Wireless Network Connection window.

3. Click the Properties button.

4. Select the General tab, and click the Configure button.

5. In the Properties window, click the Advanced tab.

6. Select Power Output.

7. From the pull-down menu on the right, select the adapter’s power output percentage.

Windows 2000

1. Open the Control Panel.

2. Double-click Network and Dial-Up Connections.

3. Select your current wireless connection, and select Properties.

4. From the Properties screen, click the Configure button.

5. Click the Advanced tab, and select Power Output.

6. From the pull-down menu on the right, select the adapter’s power setting.

If your computer is running Windows Millennium or 98, then refer to Windows Help for instructions on how to access the

advanced settings of a network adapter.

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

Wireless Access Points, Routers, or Other Wireless Products

If you have a different wireless product, use its Web-based Utility to configure its power output setting (refer to the

product’s documentation for more information).

Technical Documents on www.linksys.eu or linksys.com/international

Follow these steps to access technical documents:

1. Enter http://www.linksys.eu or linksys.com/international in your web browser.

2. Select the country or region in which you live.

3. Click the Products tab.

4. Select the appropriate product category.

5. Select the product sub-category, if necessary.

6. Select the product.

7. Select the type of documentation you want from the More Information section. The document will open in PDF format if

you have Adobe Acrobat installed on your computer.

NOTE: If you have questions regarding the compliance of this product or you cannot find the information you need,

please contact your local sales office or visit http://www.linksys.eu or linksys.com/international for more details.

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic

Equipment (WEEE)

This document contains important information for users with regards to the proper disposal and recycling of Linksys

products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

Appendix I: Regulatory Information

Wireless-G Broadband Router with SpeedBooster

For more information, visit www.linksys.com.

Wireless-G Broadband Router with SpeedBooster

Appendix I: Contact Information

Need to contact Linksys?

Visit us online for information on the latest products and updates to your existing products at:

http://www.linksys.eu or linksys.com/international

If you experience problems with any Linksys product, you can e-mail us at:

In Europe E-mail Address

Austria support.at@linksys.com

Belgium [email protected]

Czech Republic suppor[email protected]

Denmark [email protected]

Finland support.fi@linksys.com

France support.fr@linksys.com

Germany support.de@linksys.com

Greece support.gr@linksys.com (English only)

Hungary [email protected]

Ireland support.ie@linksys.com

Italy support.it@linksys.com

Netherlands suppor[email protected]

Norway [email protected]

Poland support.[email protected]

Portugal support.pt@linksys.com

Russia support.ru@linksys.com

Spain [email protected]

Sweden support.[email protected]

Wireless-G Broadband Router with SpeedBooster

Appendix I: Contact Information

Note: For some countries, support may be available only in English.

Switzerland support.ch@linksys.com

Turkey suppor[email protected]m

United Kingdom [email protected]

Outside of Europe E-mail Address

Asia Pacific asiasupport@linksys.com (English only)

Latin America support.portuguese@linksys.com or support.s[email protected]

Middle East & Africa support.me[email protected] (English only)

South Africa support.ze@linksys.com (English only)

UAE [email protected] (English only)

U.S. and Canada [email protected]

In Europe E-mail Address

Modell-Nr.

Broadband-Router

Wireless-G

WRT54GS (DE)

Benutzerhandbuch

WIRELESS

mit SpeedBooster

GHz

802.11g

2,4

Wireless-G Broadband-Router mit SpeedBooster

Technische Änderungen vorbehalten. Linksys ist eine eingetragene Marke bzw. eine Marke von Cisco Systems, Inc.

Rechte vorbehalten. Andere Handelsmarken und Produktnamen sind Marken bzw. eingetragene Marken der jeweiligen

Inhaber.

Hinweise zur Verwendung dieses Benutzerhandbuchs

Ziel dieses Benutzerhandbuchs ist, Ihnen den Einstieg in den Netzwerkbetrieb mit dem Wireless-G Broadband-

Router noch einfacher zu machen. Achten Sie beim Lesen dieses Benutzerhandbuchs auf folgende Symbole:

Zusätzlich zu diesen Symbolen finden Sie auch Definitionen für technische Begriffe, die in folgender Form

dargestellt werden:

Alle Abbildungen (Diagramme, Bildschirmdarstellungen und andere Bilder) sind mit einer Abbildungsnummer und

einer Kurzbeschreibung versehen (siehe folgendes Beispiel):

Die Abbildungsnummern und die zugehörigen Kurzbeschreibungen finden Sie auch im Inhaltsverzeichnis unter

„Abbildungsverzeichnis“.

Dieses Ausrufezeichen kennzeichnet eine Warnung und weist darauf

hin, dass unter bestimmten Umständen Schäden an Ihrem Eigentum

oder am Wireless-G Broadband-Router verursacht werden können.

Dieses Häkchen kennzeichnet einen Hinweis darauf, dass bei

Verwendung des Wireless-G Broadband-Routers etwas beachtet

werden sollte.

Dieses Fragezeichen dient als Erinnerung an bestimmte Schritte,

die bei Verwendung des Wireless-G Broadband-Routers

durchzuführen sind.

Wort: Definition.

Abbildung 0-1: Beschreibung der Beispielabbildung

WRT54GSV7-DE-UG-70206NC BW

Wireless-G Broadband-Router mit SpeedBooster

Inhalt

Kapitel 1: Einführung 1

Willkommen 1

Der Inhalt dieses Handbuchs 2

Kapitel 2: Planen des Wireless-Netzwerks 4

Netzwerktopologie 4

Der Unterschied zwischen Ad-Hoc- und Infrastrukturmodus 4

Netzwerkanordnung 5

Kapitel 3: Kennenlernen des Wireless-G Broadband-Routers 6

Rückseite 6

Vorderseite 7

Kapitel 4: Anschließen des Wireless-G Broadband-Routers 9

Übersicht 9

Hardware-Installation für Verbindungen mit dem Breitband-Modem 9

Hardware-Installation für die Verbindung von Routern 11

Kapitel 5: Konfigurieren des Wireless-G Broadband-Routers mit SRX400 14

Übersicht 14

Die Registerkarte „Setup“ (Einrichtung) - „Basic Setup“ (Grundlegende Einrichtung) 15

Die Registerkarte „Setup“ (Einrichtung) - „DDNS“ 20

Die Registerkarte „Setup“ (Einrichtung) - „MAC Address Clone“

(MAC-Adresse kopieren) 21

Die Registerkarte „Setup“ (Einrichtung) - „Advanced Routing“ (Erweitertes Routing) 22

Die Registerkarte „Wireless“ - „Basic Wireless Settings“ (Grundlegende

Wireless-Einstellungen) 24

Die Registerkarte „Wireless“ - „Wireless Security“ (Wireless-Sicherheit) 25

Die Registerkarte „Wireless“ - „Wireless MAC Filter“ (Wireless-MAC-Filter) 28

Die Registerkarte „Wireless“ - „Advanced Wireless Settings“ (Erweiterte

Wireless-Einstellungen) 29

Die Registerkarte „Security“ (Sicherheit) - „Firewall“ 31

Die Registerkarte „Security“ (Sicherheit) - „VPN Passthrough“ (VPN-Passthrough) 32

Die Registerkarte „Access Restrictions“ (Zugriffsbeschränkungen) -

„Internet Access“ (Internetzugriff) 33

Die Registerkarte „Applications & Gaming“ (Anwendungen & Spiele) -

„Port Range Forward“ (Port-Bereich-Weiterleitung) 35

Die Registerkarte „Applications & Gaming“ (Anwendungen & Spiele) -

„Port Triggering“ (Port-Triggering) 36

Wireless-G Broadband-Router mit SpeedBooster

Die Registerkarte „Applications & Gaming“ (Anwendungen & Spiele) - „DMZ“ 37

Die Registerkarte „Applications & Gaming“ (Anwendungen & Spiele) - „QoS“ 37

Die Registerkarte „Administration“ (Verwaltung) - „Management“

(Verwaltungsfunktionen) 39

Die Registerkarte „Administration“ (Verwaltung) - „Log“ (Protokoll) 39

Die Registerkarte „Administration“ (Verwaltung) - „Diagnostics“ (Diagnose) 40

Die Registerkarte „Administration“ (Verwaltung) - „Factory Defaults“

(Werkseinstellungen) 41

Die Registerkarte „Administration“ (Verwaltung) - „Firmware Upgrade“

(Aktualisieren der Firmware) 41

Die Registerkarte „Administration“ (Verwaltung) - „Config Management“

(Konfigurationsverwaltung) 42

Die Registerkarte „Status“ - „Router“ 43

Die Registerkarte „Status“ - „Local Network“ (Lokales Netzwerk) 44

Die Registerkarte „Status“ - „Wireless“ 45

Anhang A: Fehlerbehebung 46

Behebung häufig auftretender Probleme 46

Häufig gestellte Fragen 57

Anhang B: „Wireless Security“ (Wireless-Sicherheit) 65

Vorsichtsmaßnahmen 65

Sicherheitsrisiken bei Wireless-Netzwerken 65

Anhang C: Aktualisieren der Firmware 69

Anhang D: Windows-Hilfe 70

Anhang E: Ermitteln der MAC-Adresse und der IP-Adresse des

Ethernet-Adapters 71

Anweisungen für Windows 98 SE/ME 71

Anweisungen für Windows 2000/XP 71

Im webbasierten Dienstprogramm des Routers 72

Anhang F: Glossar 73

Anhang G: Spezifikationen 78

Anhang H: Garantieinformationen 80

Anhang I: Zulassungsinformationen 81

Anhang J: Kontaktinformationen 95

Wireless-G Broadband-Router mit SpeedBooster

Abbildungsverzeichnis

Abbildung 3-1: Rückseite des Routers 6

Abbildung 3-2: Vorderseite des Routers 7

Abbildung 4-1: Anschließen des Modems an den Internet-Port des Routers 9

Abbildung 4-2: Anschließen der Netzwerkgeräte 10

Abbildung 4-3: Anschließen des Netzstromkabels 10

Abbildung 4-4: Verbinden von Routern hintereinander 11

Abbildung 4-5: Beispiel für eine Verbindung mit einem anderen Router 11

Abbildung 4-6: Verbinden Sie den Internet-Port des Broadband-Routers mit dem nummerierten

Ethernet-Port des anderen Routers. 12

Abbildung 4-7: Anschließen der Netzwerkgeräte 12

Abbildung 4-8: Anschließen des Netzstromkabels 13

Abbildung 5-1: Fenster zur Kennworteingabe 14

Abbildung 5-2: Registerkarte zur Einrichtung: „Basic Setup“ (Grundlegende Einrichtung) 15

Abbildung 5-3: Verbindungstyp „DHCP“ 15

Abbildung 5-4: Verbindungstyp „Statische IP-Adresse“ 15

Abbildung 5-5: Verbindungstyp „PPPoE“ 16

Abbildung 5-6: Verbindungstyp „PPTP“ 16

Abbildung 5-7: Verbindungstyp „Telstra-Kabel“ 17

Abbildung 5-8: Verbindungstyp „L2TP“ 17

Abbildung 5-9: „Optional Settings“ (Optionale Einstellungen) 18

Abbildung 5-10: IP-Adresse des Routers 18

Abbildung 5-11: „Network Address Server Settings“ (Einstellungen des Netzwerkadressenservers) 18

Abbildung 5-12: „Time Setting“ (Zeiteinstellung) 19

Abbildung 5-13: Registerkarte zur Einrichtung: „DDNS“ - „DynDNS“ 20

Abbildung 5-14: Registerkarte zur Einrichtung: „DDNS“ - „TZO“ 20

Abbildung 5-15: Registerkarte zur Einrichtung: „MAC Address Clone“ (Kopieren der MAC-Adresse) 21

Abbildung 5-16: Registerkarte zur Einrichtung: „Advanced Routing (Gateway)“ (Erweitertes Routing (Gateway)) 22

Abbildung 5-17: Registerkarte zur Einrichtung: „Advanced Routing (Router)“ (Erweitertes Routing (Router)) 22

Abbildung 5-18: Registerkarte Wireless: „Basic Wireless Settings“ (Grundlegende Wireless-Einstellungen) 24

Abbildung 5-19: Registerkarte Wireless: „Wireless Security (WPA Personal)“ (Wireless Sicherheit

(WPA Personal)) 25

Wireless-G Broadband-Router mit SpeedBooster

Abbildung 5-20: Registerkarte Wireless: „Wireless Security (WPA Enterprise)“ (Wireless-Sicherheit

(WPA Enterprise)) 25

Abbildung 5-21: Registerkarte Wireless: „Wireless Security (WPA Personal)“ (Wireless Sicherheit

(WPA Personal)) 26

Abbildung 5-22: Registerkarte Wireless: „Wireless Security (WPA Enterprise)“ (Wireless Sicherheit

(WPA Enterprise)) 26

Abbildung 5-23: Registerkarte Wireless: „Wireless Security (RADIUS)“ (Wireless-Sicherheit (RADIUS)) 27

Abbildung 5-24: Registerkarte Wireless: „Wireless Security (WEP)“ (Wireless-Sicherheit (WEP)) 27

Abbildung 5-25: Registerkarte Wireless: „Wireless MAC Filter“ (Wireless-MAC-Filter) 28

Abbildung 5-26: „MAC Address Filter List“ (MAC-Adressen-Filterliste) 28

Abbildung 5-27: Registerkarte Wireless: „Advanced Wireless Settings“ (Erweiterte Wireless-Einstellungen) 29

Abbildung 5-28: Registerkarte für die Sicherheitseinstellungen: „Firewall“ 31

Abbildung 5-29: Registerkarte für die Sicherheitseinstellungen: „VPN Passthrough“ (VPN-Passthrough) 32

Abbildung 5-30: Registerkarte für Zugriffsbeschränkungen: „Internet Access“ (Internetzugriff) 33

Abbildung 5-31: „Internet Policy Summary“ (Zusammenfassung der Internetrichtlinien) 33

Abbildung 5-32: „List of PCs“ (PC-Liste) 33

Abbildung 5-33: Anschlussdienste 34

Abbildung 5-34: Registerkarte für Anwendungen und Spiele: „Port Range Forward“

(Port-Bereich-Weiterleitung) 35

Abbildung 5-35: Registerkarte für Anwendungen und Spiele: „Port Triggering“ (Port-Triggering) 36

Abbildung 5-36: Registerkarte für Anwendungen und Spiele: „DMZ“ 37

Abbildung 5-37: Registerkarte für Anwendungen und Spiele: „QoS“ 37

Abbildung 5-38: Registerkarte zur Verwaltung: „Management“ (Verwaltungsfunktionen) 39

Abbildung 5-39: Registerkarte zur Verwaltung: „Log“ (Protokoll) 39

Abbildung 5-40: Registerkarte zur Verwaltung: „Diagnostics“ (Diagnose) 40

Abbildung 5-41: Ping-Test 40

Abbildung 5-42: Test zur Routenverfolgung 40

Abbildung 5-43: Registerkarte zur Verwaltung: „Factory Defaults“ (Werkseinstellungen) 41

Abbildung 5-44: Registerkarte zur Verwaltung: „Firmware Upgrade“ (Aktualisieren der Firmware) 41

Abbildung 5-45: Registerkarte zur Verwaltung: „Config Management“ (Konfigurationsverwaltung) 42

Abbildung 5-46: Registerkarte zum Status: „Router“ 43

Abbildung 5-47: Registerkarte zum Status: „Local Network“ (Lokales Netzwerk) 44

Abbildung 5-48: DHCP-Client-Tabelle 44

Abbildung 5-49: Registerkarte zum Status: „Wireless“ 45

Wireless-G Broadband-Router mit SpeedBooster

Abbildung C-1: „Upgrade Firmware“ (Firmware aktualisieren) 69

Abbildung E-1: Fenster zur IP-Konfiguration 71

Abbildung E-2: MAC-Adresse/Adapteradresse 71

Abbildung E-3: MAC-Adresse/physische Adresse 71

Abbildung E-4: „MAC Address Filter List“ (MAC-Adressen-Filterliste) 72

Abbildung E-5: „MAC Address Clone“ (MAC-Adresse kopieren) 72

Kapitel 1: Einführung

Willkommen

Wireless-G Broadband-Router mit SpeedBooster

Kapitel 1: Einführung

Willkommen

Vielen Dank, dass Sie sich für einen Wireless-G Broadband-Router mit SpeedBooster von Linksys entschieden

haben. Der Wireless-G Broadband-Router mit SpeedBooster optimiert den Wireless-Netzwerkbetrieb wie nie

zuvor, sodass Sie einfach und sicher auf das Internet, Dateien und jede Menge Spaß zugreifen können.

Wie macht der Wireless-G Broadband-Router mit SpeedBooster das möglich? Ein Router ist ein Gerät, mit dem über

ein Netzwerk auf eine Internetverbindung zugegriffen werden kann. Mit dem Wireless-G Broadband-Router mit

SpeedBooster kann dieser Zugriff über einen der vier Switched Ports und über das Wireless-Netzwerk mit 11 Mbit/s

für Wireless-B bzw. 54 Mbit/s für Wireless-G erfolgen. Darüber hinaus bietet die WEP-Verschlüsselung bessere

Sicherheitsoptionen, während das gesamte Netzwerk durch die SPI-Firewall (Stateful Packet Inspection) und NAT-

Technologie geschützt ist. Der Zugriff auf diese Sicherheitsfunktionen sowie umfassende

Konfigurationsmöglichkeiten erfolgt über ein benutzerfreundliches, browserbasiertes Dienstprogramm.

Und was genau bedeutet das?

Netzwerke sind nützliche Werkzeuge zur gemeinsamen Nutzung von Computerressourcen. Sie können von

verschiedenen Computern aus auf einem Drucker drucken und auf Daten zugreifen, die auf der Festplatte eines

anderen Computers gespeichert sind. Netzwerke eignen sich darüber hinaus auch für Videospiele mit mehreren

Spielern. Netzwerke sind also nicht nur zu Hause und im Büro nützlich, sondern lassen sich auch für

Unterhaltungszwecke nutzen.

PCs in einem Wired-Netzwerk stellen ein LAN (Local Area Network; lokales Netzwerk) dar. Sie werden über

Ethernetkabel angeschlossen, daher die Bezeichnung „Wired-Netzwerk“.

Mit Wireless-Karten oder -Adaptern ausgerüstete PCs können ganz ohne lästige Kabel kommunizieren. Sie

verwenden innerhalb des Übertragungsradius dieselben Wireless-Einstellungen und bilden so ein Wireless-

Netzwerk. Der Wireless-G Broadband-Router mit SpeedBooster fungiert als Bridge zwischen Wireless-

Netzwerken des Standards 802.11b und 802.11g und Wired-Netzwerken, sodass diese miteinander

kommunizieren können. Und da dieser Router über die SpeedBooster-Technologie verfügt, erhöht sich die

Leistung des Wireless-Netzwerks um bis zu 30 % gegenüber älteren 802.11g-Standards. Sie werden feststellen,

dass sogar Geräte, die nicht mit SpeedBooster ausgestattet sind, eine höhere Geschwindigkeit erreichen, wenn

sie mit SpeedBooster-Geräten kommunizieren.

Durch das Verbinden aller Wired- und Wireless-Netzwerke sowie des Internets können Sie jetzt Dateien zur

gemeinsamen Verwendung nutzen, auf das Internet zugreifen und sogar Spiele spielen. Und dabei schützt der

Wireless-G Broadband-Router mit SpeedBooster Ihre Netzwerke stets vor nicht autorisierten und nicht

willkommenen Benutzern.

Kapitel 1: Einführung

Der Inhalt dieses Handbuchs

Wireless-G Broadband-Router mit SpeedBooster

Sie sollten immer die Installations-CD-ROM verwenden, wenn Sie den Router erstmals installieren. Wenn Sie den

Setup-Assistenten auf der Installations-CD-ROM nicht ausführen möchten, befolgen Sie die in diesem Handbuch

aufgeführten Anleitungsschritte, um den Wireless-G Broadband-Router mit SpeedBooster anzuschließen,

einzurichten und für die Verbindung Ihrer verschiedenen Netzwerke zu konfigurieren. Diese Anleitungen

enthalten alle Informationen, die Sie benötigen, um den Wireless-G Broadband-Router mit SpeedBooster optimal

zu verwenden.

Der Inhalt dieses Handbuchs

In diesem Benutzerhandbuch sind die zur Installation und Verwendung des Wireless-G Broadband-Routers mit

SpeedBooster erforderlichen Schritte aufgeführt.

• Kapitel 1: Einführung

In diesem Kapitel werden die Anwendungen des Routers sowie dieses Benutzerhandbuch beschrieben.

• Kapitel 2: Planen des Wireless-Netzwerks

In diesem Kapitel werden die Grundlagen des Wireless-Netzwerkbetriebs beschrieben.

• Kapitel 3: Kennenlernen des Wireless-G Broadband-Routers

In diesem Kapitel werden die physischen Merkmale des Routers beschrieben.

• Kapitel 4: Anschließen des Wireless-G Broadband-Routers

In diesem Kapitel finden Sie Anleitungen zum Anschließen des Routers an Ihr Netzwerk.

• Kapitel 6: Konfigurieren des Wireless-G Broadband-Routers

In diesem Kapitel wird beschrieben, wie Sie das webbasierte Dienstprogramm des Routers verwenden.

• Anhang A: Fehlerbehebung

In diesem Anhang werden einige Probleme und Lösungsansätze sowie häufig gestellte Fragen im

Zusammenhang mit der Installation und Verwendung des Wireless-G Broadband-Routers erörtert.

• Anhang B: Wireless-Sicherheit

In diesem Anhang werden die Risiken des Wireless-Netzwerkbetriebs sowie einige Lösungen zur

Eingrenzung der Risiken erklärt.

• Anhang C: Aktualisieren der Firmware

In diesem Anhang finden Sie Anleitungen dazu, wie Sie die Firmware des Routers aktualisieren, falls dies

einmal erforderlich sein sollte.

Kapitel 1: Einführung

Der Inhalt dieses Handbuchs

Wireless-G Broadband-Router mit SpeedBooster

• Anhang D: Windows-Hilfe

In diesem Anhang wird beschrieben, wie Sie in der Windows-Hilfe Anleitungen und Informationen zum

Netzwerkbetrieb finden, wie beispielsweise zur Installation des TCP/IP-Protokolls.

• Anhang E: Ermitteln der MAC-Adresse und der IP-Adresse des Ethernet-Adapters

In diesem Anhang wird beschrieben, wie Sie die MAC-Adresse für den Ethernet-Adapter Ihres Computers

ermitteln, um die MAC-Filterung bzw. die Router-Funktion zum Kopieren von MAC-Adressen verwenden zu

können.

• Anhang F: Glossar

In diesem Anhang finden Sie ein kurzes Glossar mit häufig verwendeten Begriffen aus dem Bereich

Netzwerkbetrieb.

• Anhang G: Spezifikationen

In diesem Anhang sind die technischen Spezifikationen des Routers aufgeführt.

• Anhang H: Garantieinformationen

Dieser Anhang enthält die Garantieinformationen für den Router.

• Anhang I: Zulassungsinformationen

Dieser Anhang enthält die für den Router geltenden Zulassungsinformationen.

• Anhang J: Kontaktinformationen

In diesem Anhang finden Sie Kontaktinformationen zu einer Reihe von Linksys Ressourcen, darunter auch

zum Support.

Kapitel 2: Planen des Wireless-Netzwerks

Netzwerktopologie

Wireless-G Broadband-Router mit SpeedBooster

Kapitel 2: Planen des Wireless-Netzwerks

Netzwerktopologie

WLANs (Wireless Local Area Network) entsprechen im Prinzip regulären LANs (Local Area Network), mit der

Ausnahme, dass jeder Computer im Wireless-Netzwerk die Verbindung zum Netzwerk über ein Wireless-Gerät

herstellt. Computer in einem Wireless-Netzwerk verwenden denselben Frequenzkanal und dieselbe SSID

(Identifizierungsname, der von den zum selben Wireless-Netzwerk gehörenden Wireless-Geräten gemeinsam

verwendet wird).

Der Unterschied zwischen Ad-Hoc- und Infrastrukturmodus

Im Gegensatz zu Wired-Netzwerken können Wireless-Netzwerke in zwei verschiedenen Modi eingerichtet

werden: dem Ad-Hoc- und dem Infrastrukturmodus. Bei einer Konfiguration im Infrastrukturmodus

kommunizieren ein Wireless-Netzwerk und ein Wired-Netzwerk über einen Access Point miteinander. Bei einer

Konfiguration im Ad-Hoc-Modus kommunizieren wireless-fähige Computer direkt miteinander. Die Entscheidung

zwischen diesen zwei Modi hängt davon ab, ob Daten oder Peripheriegeräte im Wireless-Netzwerk gemeinsam

mit einem Wired-Netzwerk verwendet werden müssen.

Wenn auf die Computer im Wireless-Netzwerk von einem Wired-Netzwerk aus zugegriffen wird bzw. wenn die

Computer sich ein Peripheriegerät, beispielsweise einen Drucker, mit Computern in einem Wired-Netzwerk teilen,

sollte das Wireless-Netzwerk für den Infrastrukturmodus eingerichtet sein. Der Ausgangspunkt des

Infrastrukturmodus liegt bei einem Wireless-Router oder einem Access Point, der als Hauptkommunikationsstelle

in einem Wireless-Netzwerk dient. Der Router überträgt Daten an PCs, die mit Adaptern für den Wireless-

Netzwerkbetrieb ausgerüstet und innerhalb eines gewissen Bereichs um den Router roaming-fähig sind. Sie

können den Router und mehrere Access Points so anordnen, dass diese in Folge arbeiten, wodurch sich die

Roaming-Reichweite erweitert; darüber hinaus können Sie Ihr Wireless-Netzwerk so einrichten, dass es auch mit

Ihrer Ethernet-Hardware kommuniziert.

Wenn das Wireless-Netzwerk relativ klein ist und nur mit den anderen Computern im Wireless-Netzwerk

Ressourcen teilt, kann der Ad-Hoc-Modus verwendet werden. Der Ad-Hoc-Modus ermöglicht es Computern, die

mit Wireless-Transmittern und -Empfängern ausgerüstet sind, direkt miteinander zu kommunizieren, sodass

keine Wireless-Router oder Access Points nötig sind. Der Nachteil dieses Modus liegt darin, dass wireless-fähige

Computer im Ad-Hoc-Modus nicht mit Computern in einem Wired-Netzwerk kommunizieren können. Außerdem

ist die Kommunikation zwischen den wireless-fähigen Computern von der Entfernung und den Interferenzen

zwischen den Computern abhängig.

Kapitel 2: Planen des Wireless-Netzwerks

Netzwerkanordnung

Wireless-G Broadband-Router mit SpeedBooster

Netzwerkanordnung

Der Wireless-G Broadband-Router wurde speziell zur Verwendung sowohl mit 802.11b- als auch 802.11g-

Produkten entwickelt. Produkte, die diese Standards verwenden, können nun miteinander kommunizieren.

Der Wireless-G Broadband-Router ist mit allen 802.11b- und 802.11g-Adaptern kompatibel, wie beispielsweise

den Notebook-Netzwerkkarten für Ihren Laptop, PCI-Adaptern für Ihren Desktop-PC und USB-Adaptern, wenn Sie

den Komfort der USB-Konnektivität genießen möchten. Der Broadband-Router kommuniziert auch mit dem

Wireless-Druckserver und Wireless Ethernet Bridges.

Wenn Sie Ihr Wireless-Netzwerk mit Ihrem Wired-Netzwerk verbinden möchten, können Sie dazu die vier LAN-

Ports des Wireless-G Broadband-Routers verwenden. Falls Sie weitere Ports benötigen, lässt sich jeder LAN-Port

des Wireless-G Broadband-Routers mit einem beliebigen Switch von Linksys verbinden.

Mit diesen und zahlreichen weiteren Linksys Produkten stehen Ihnen grenzenlose Möglichkeiten für Ihren

Netzwerkbetrieb zur Verfügung. Weitere Informationen dazu, welche Produkte mit dem Wireless-G Broadband-

Router verwendet werden können, finden Sie auf der Website von Linksys unter www.linksys.eu oder

linksys.com/international.

Kapitel 3: Kennenlernen des Wireless-G Broadband-Routers

Rückseite

Wireless-G Broadband-Router mit SpeedBooster

Kapitel 3: Kennenlernen des Wireless-G Broadband-

Routers

Rückseite

Die Ports des Routers zum Anschließen von Kabeln befinden sich auf der Rückseite.

Reset-Taste (Zurücksetzen) Der Router kann auf zweierlei Weise auf die Werkseinstellungen zurückgesetzt

werden. Halten Sie entweder die Reset-Taste ungefähr fünf Sekunden lang

gedrückt, oder stellen Sie die Standardeinstellungen im Web-basierten

Dienstprogramm des Routers auf der Registerkarte Administration (Verwaltung)

unter Factory Defaults (Werkseinstellungen) wieder her.

Internet Der Internet-Port dient zum Anschließen an Ihre Breitband-Internetverbindung.

1, 2, 3, 4 Diese Ports (1, 2, 3, 4) verbinden den Router mit PCs in Wired-Netzwerken und

anderen Ethernet-Netzwerkgeräten.

Power (Netzstrom) Das Netzteil wird am Netzstromanschluss angeschlossen.

WICHTIG: Durch das Zurücksetzen des

Routers werden alle Einstellungen (WEP-

Verschlüsselung, Netzwerkeinstellungen usw.)

gelöscht und durch die Werkseinstellungen

ersetzt. Wenn Sie diese Einstellungen

beibehalten möchten, sollten Sie den Router

nicht zurücksetzen.

Abbildung 3-1: Rückseite des Routers

Kapitel 3: Kennenlernen des Wireless-G Broadband-Routers

Vorderseite

Wireless-G Broadband-Router mit SpeedBooster

Vorderseite

Auf der Vorderseite des Routers befinden sich die LEDs, mit denen Informationen zur Netzwerkaktivität angezeigt

werden.

(Cisco Logo) Orange/weiß. Das Cisco Logo stellt die SecureEasySetup-Taste des Routers dar.

Es leuchtet nach dem Einschalten des Routers konstant orange. Die Farbe Orange

zeigt an, dass die SecureEasySetup-Funktion nicht vom Router verwendet wird,

während die Farbe Weiß darauf hinweist, dass der Router die SecureEasySetup-

Funktion verwendet. Wenn der Router in den SecureEasySetup-Modus wechselt,

blinkt das Cisco Logo zunächst weiß. Sobald der Router die SSID und den

gemeinsamen WPA-Schlüssel erzeugt hat, leuchtet das Cisco Logo konstant weiß.

Drücken Sie zum Löschen der SSID und des gemeinsamen WPA-Schlüssels fünf

Sekunden lang auf das Cisco Logo. Das Cisco Logo blinkt während des

Zurücksetzens des Routers langsam. Bei erfolgreichem Zurücksetzen leuchtet das

Cisco Logo danach orange.

Power (Netzstrom) Grün. Die Netzstrom-LED leuchtet so lange, wie der Router eingeschaltet ist. Wenn

der Router beim Hochfahren eine Selbstdiagnose durchführt, blinkt die LED. Nach

Abschluss der Diagnose leuchtet die LED konstant.

DMZ Grün. Die DMZ-LED zeigt an, dass die DMZ-Funktion verwendet wird. Diese LED

leuchtet, solange DMZ aktiviert ist.

WLAN Grün. Die WLAN-LED leuchtet, wenn die Wireless-Funktion aktiviert ist. Wenn die

LED blinkt, sendet oder empfängt der Router aktiv Daten über das Netzwerk.

Abbildung 3-2: Vorderseite des Routers

HINWEIS: Bei SecureEasySetup handelt es sich um

eine Funktion, mit der Sie auf einfache Weise das

Wireless-Netzwerk einrichten können. Wenn Sie über

SecureEasySetup-Geräte verfügen, führen Sie die

Setup-Assistenten-CD-ROM des Routers aus, und

befolgen Sie dann die Anweisungen auf dem

Bildschirm für die Verwendung von

SecureEasySetup. Sie können auch über das

webbasierte Dienstprogram auf SecureEasySetup

zugreifen, wenn Sie den Setup-Assistenten nicht

ausführen.

Kapitel 3: Kennenlernen des Wireless-G Broadband-Routers

Vorderseite

Wireless-G Broadband-Router mit SpeedBooster

1, 2, 3, 4 Grün. Diese nummerierten LEDs entsprechen den nummerierten Ports auf der

Rückseite des Routers und dienen den beiden folgenden Zwecken: Wenn die

betreffende LED konstant leuchtet, ist der Router über diesen Port erfolgreich mit

einem Gerät verbunden. Wenn die betreffende LED blinkt, findet an diesem Port

Netzwerkaktivität statt.

Internet Grün. Die Internet-LED leuchtet auf, wenn eine Verbindung über den Internet-Port

hergestellt wird.

Kapitel 4: Anschließen des Wireless-G Broadband-Routers

Übersicht

Wireless-G Broadband-Router mit SpeedBooster

Kapitel 4: Anschließen des Wireless-G Broadband-

Routers

Übersicht

Dieses Kapitel enthält zwei verschiedene Anleitungsblöcke. Wenn der Wireless-G Broadband-Router der einzige

Router in Ihrem Netzwerk ist, befolgen Sie die Anweisungen unter „Hardware-Installation für Verbindungen mit dem

Breitband-Modem“. Wenn Sie bestimmte Anwendungen nur auf bestimmten PCs ausführen möchten, muss der

Wireless-G Broadband-Router dazu hinter einem anderen Router ausgeführt werden. Wenn Sie den Wireless-G

Broadband-Router hinter einem anderen Router in Ihrem Netzwerk ausführen möchten, befolgen Sie die

Anweisungen unter „Verbinden von Routern“.

Hardware-Installation für Verbindungen mit dem Breitband-Modem

1. Schalten Sie Ihre Netzwerkgeräte aus.

2. Ermitteln Sie die optimale Installationsposition für den Router. Optimal ist in der Regel eine zentrale Position

im Wireless-Netzwerk in Sichtweite aller mobilen Arbeitsstationen.

3. Fixieren Sie die Ausrichtung der Antennen. Installieren Sie den Router nach Möglichkeit in einer Position, in

der Ihr Wireless-Netzwerk optimal abgedeckt ist. Je höher Sie die Antenne anbringen, desto besser ist in der

Regel die Leistung.

4. Schließen Sie ein Standard-Ethernet-Netzwerkkabel am Internet-Port des Routers an. Schließen Sie dann das

andere Ende des Ethernet-Kabels an Ihr Kabel- oder DSL-Breitband-Modem an.

Abbildung 4-1: Anschließen des Modems an den Internet-Port des Routers

Kapitel 4: Anschließen des Wireless-G Broadband-Routers

Hardware-Installation für Verbindungen mit dem Breitband-Modem

Wireless-G Broadband-Router mit SpeedBooster

5. Schließen Sie Ihre Netzwerk-PCs oder Ethernet-Geräte mit Standard-Ethernet-Netzwerkkabeln an die

nummerierten Ports des Routers an.

6. Schließen Sie das Netzteil an den Stromanschluss des Routers an, und stecken Sie das andere Ende in eine

Netzsteckdose.

Wenn Sie über ein Netzteil und ein separates Netzkabel verfügen, schließen Sie das Netzkabel an das Netzteil

an, und verbinden Sie anschließend das Netzteil mit dem Power-Port des Routers. Stecken Sie das Netzkabel

in eine Steckdose.

Die Hardware-Installation ist nun abgeschlossen. Fahren Sie mit „Kapitel 5: Konfigurieren des

Wireless-G Broadband-Routers“ fort, in dem Sie Anweisungen zur Verwendung des webbasierten

Dienstprogramms zur Konfiguration der Router-Einstellungen für Ihr Netzwerk finden.

Abbildung 4-3: Anschließen des Netzstromkabels

WICHTIG: Verwenden Sie nur das Netzteil, das im

Lieferumfang des Routers enthalten ist. Bei

Verwendung eines anderen Netzteils könnte der

Router beschädigt werden.

Abbildung 4-2: Anschließen der Netzwerkgeräte

Kapitel 4: Anschließen des Wireless-G Broadband-Routers

Hardware-Installation für die Verbindung von Routern

Wireless-G Broadband-Router mit SpeedBooster

Hardware-Installation für die Verbindung von Routern

Bestimmte Anwendungen wenden Einstellungen auf alle mit dem Router verbundenen PCs an. Unter Umständen

möchten Sie diese Einstellungen jedoch nicht auf alle PCs in Ihrem Netzwerk anwenden.

Vergewissern Sie sich vor dem Verbinden der Router, dass diese verschiedene IP-Adressen aufweisen. Führen

Sie diese Überprüfung unbedingt durch, da die Router unter Umständen ab Werk standardmäßig auf dieselbe IP-

Adresse eingestellt sind.

Vergewissern Sie sich zuerst, dass der Router NICHT mit Ihrem Netzwerk verbunden ist. Befolgen Sie dann die

folgenden Anweisungen:

1. Starten Sie zum Zugriff auf das webbasierte Dienstprogramm des anderen Routers Ihren Webbrowser, und

geben Sie die standardmäßige IP-Adresse des anderen Routers (192.168.1.1) bzw. die von Ihnen eingestellte

IP-Adresse in das Feld Address (Adresse) ein. Drücken Sie anschließend die Eingabetaste.

2. Es wird ein Fenster angezeigt, in dem Sie nach Ihrem Kennwort gefragt werden. Lassen Sie das Feld

Benutzername leer. Geben Sie im Feld Kennwort das eingestellte Kennwort ein (das Standardkennwort lautet

admin). Klicken Sie anschließend auf die Schaltfläche OK.

3. Im ersten Fenster wird die Registerkarte Setup (Einrichtung) angezeigt. Im Abschnitt Network Setup

(Netzwerkeinrichtung) befindet sich die Einstellung Local IP Address (Lokale IP-Adresse), die auf

192.168.1.1. gesetzt ist. Ändern Sie diese in 192.168.2.1.

4. Klicken Sie auf die Schaltfläche Save Settings (Einstellungen speichern), um Ihre Änderung zu speichern,

und schließen Sie dann das webbasierte Dienstprogramm.

5. Schalten Sie Ihre Netzwerkgeräte aus. Sie beginnen nun mit der Hardware-Installation des Broadband-

Routers.

6. Ermitteln Sie die optimale Installationsposition für den Broadband-Router. Optimal ist in der Regel eine

zentrale Position im Wireless-Netzwerk in Sichtweite aller mobilen Arbeitsstationen.

7. Fixieren Sie die Ausrichtung der Antennen. Installieren Sie den Router nach Möglichkeit in einer Position, in

der Ihr Wireless-Netzwerk optimal abgedeckt ist. Je höher Sie die Antenne anbringen, desto besser ist in der

Regel die Leistung.

Abbildung 4-5: Beispiel für eine Verbindung mit einem

anderen Router

HINWEIS: Die Schritte 1 bis 4 beziehen sich auf

typische Linksys Router. Wenn Sie jedoch einen

Router von einem anderen Anbieter als Linksys

verwenden, befolgen Sie die Anleitungen in der

Dokumentation des betreffenden Routers zum

Ändern der lokalen IP-Adresse in 192.168.2.1.

Internet

Breitband-

Modem

Router

Wireless-G

Broadband-

Router

Mehrere PCs

Internet Breitband-

Modem

Router Wireless-G

Broadband-

Router

Abbildung 4-4: Verbinden von Routern hintereinander

Kapitel 4: Anschließen des Wireless-G Broadband-Routers

Hardware-Installation für die Verbindung von Routern

Wireless-G Broadband-Router mit SpeedBooster

8. Schließen Sie ein Standard-Ethernet-Netzwerkkabel am Internet-Port des Broadband-Routers an. Schließen Sie

dann das andere Ende des Ethernet-Kabels an einen der nummerierten Ethernet-Ports am anderen Router an.

9. Wählen Sie aus, welche Netzwerkcomputer bzw. Ethernet-Geräte Sie an den Broadband-Router anschließen

möchten.

Trennen Sie die Verbindungen der ausgewählten Computer bzw. Geräte mit dem anderen Router, und schließen

Sie sie mit Standard-Ethernet-Netzwerkkabeln an die nummerierten Ports des Broadband-Routers an.

Abbildung 4-7: Anschließen der Netzwerkgeräte

Abbildung 4-6: Verbinden Sie den Internet-Port des Broadband-Routers mit dem nummerierten

Ethernet-Port des anderen Routers.

Kapitel 4: Anschließen des Wireless-G Broadband-Routers

Hardware-Installation für die Verbindung von Routern

Wireless-G Broadband-Router mit SpeedBooster

10. Schließen Sie das Netzteil an den Stromanschluss des Routers an, und stecken Sie das andere Ende in eine

Netzsteckdose.

Wenn Sie über ein Netzteil und ein separates Netzkabel verfügen, schließen Sie das Netzkabel an das Netzteil

an, und verbinden Sie anschließend das Netzteil mit dem Power-Port des Routers. Stecken Sie das Netzkabel

in eine Steckdose.

Die Hardware-Installation ist nun abgeschlossen. Fahren Sie mit „Kapitel 5: Konfigurieren des

Wireless-G Broadband-Routers“ fort, in dem Sie Anweisungen zur Verwendung des webbasierten

Dienstprogramms zur Konfiguration der Router-Einstellungen für Ihr Netzwerk finden.

Abbildung 4-8: Anschließen des Netzstromkabels

WICHTIG: Verwenden Sie nur das Netzteil, das im

Lieferumfang des Routers enthalten ist. Bei

Verwendung eines anderen Netzteils könnte der

Router beschädigt werden.

Kapitel 5: Konfigurieren des Wireless-G Broadband-Routers mit SRX400

Übersicht

Wireless-G Broadband-Router mit SpeedBooster

Kapitel 5: Konfigurieren des Wireless-G Broadband-

Routers mit SRX400

Übersicht

Sie sollten immer die Installations-CD-ROM verwenden, wenn Sie den Router erstmals installieren. Wenn Sie

den Setup-Assistenten auf der Installations-CD-ROM nicht ausführen möchten, können Sie das webbasierte

Dienstprogramm zur Konfiguration des Routers verwenden. Fortgeschrittene Benutzer können die erweiterten

Einstellungen des Routers über das webbasierte Dienstprogramm konfigurieren.

In diesem Kapitel werden alle Webseiten des Dienstprogramms und deren Hauptfunktionen beschrieben. Sie

können auf einem an den Router angeschlossenen Computer über Ihren Web-Browser auf das Dienstprogramm

zugreifen. Bei der grundlegenden Netzwerkeinrichtung verwenden die meisten Benutzer die folgenden zwei

Registerkarten des Dienstprogramms:

• Basic Setup (Grundlegende Einrichtung): Geben Sie im Fenster Basic Setup (Grundlegende Einrichtung)

die von Ihrem ISP bereitgestellten Einstellungen ein.

• Management (Verwaltungsfunktionen): Klicken Sie auf die Registerkarte Administration (Verwaltung) und

anschließend auf die Registerkarte Management (Verwaltungsfunktionen). Das Standardpasswort des

Routers lautet admin. Ändern Sie das Standardpasswort, um den Router zu schützen.

Es stehen sieben Hauptregisterkarten zur Verfügung: Setup (Einrichtung), Wireless, Security (Sicherheit),

Access Restrictions (Zugriffsbeschränkungen), Applications & Gaming (Anwendungen & Spiele),

Administration (Verwaltung) und Status. Durch Anklicken der Hauptregisterkarten werden zusätzliche

Registerkarten verfügbar.

Um auf das webbasierte Dienstprogramm zuzugreifen, starten Sie Internet Explorer oder Netscape Navigator, und

geben Sie in der Adresszeile die Standard-IP-Adresse des Routers (192.168.1.1) ein. Drücken Sie anschließend

die Eingabetaste.

Es wird ein Fenster angezeigt, in dem Sie nach Ihrem Kennwort gefragt werden. (Unter anderen

Betriebssystemen als Windows XP wird ein ähnliches Fenster angezeigt.) Lassen Sie das Feld Benutzername

leer. Wenn Sie das webbasierte Dienstprogramm zum ersten Mal öffnen, verwenden Sie das Standardkennwort

admin. (Über die Registerkarte Administration (Verwaltung) können Sie im Fenster Management

(Verwaltungsfunktionen) ein neues Kennwort festlegen.) Klicken Sie auf die Schaltfläche OK, um fortzufahren.

HABEN SIE: TCP/IP auf Ihren PCs aktiviert? PCs

tauschen über das Netzwerk mit diesem Protokoll

Daten aus. Weitere Informationen zu TCP/IP finden Sie

in „Anhang D: Windows-Hilfe“.

HINWEIS: Wenn Sie den Router erstmals installieren,

sollten Sie unbedingt den Setup-Assistenten auf der

Installations-CD-ROM verwenden. Wenn Sie die

erweiterten Einstellungen konfigurieren möchten,

erhalten Sie in diesem Kapitel Informationen über das

webbasierte Dienstprogramm.

Abbildung 5-1: Fenster zur

Kennworteingabe

Kapitel 5: Konfigurieren des Wireless-G Broadband-Routers mit SRX400

Die Registerkarte „Setup“ (Einrichtung) - „Basic Setup“ (Grundlegende Einrichtung)

Wireless-G Broadband-Router mit SpeedBooster

Die Registerkarte „Setup“ (Einrichtung) - „Basic Setup“ (Grundlegende

Einrichtung)

Im ersten geöffneten Fenster wird die Registerkarte Setup (Einrichtung) angezeigt. Hier können Sie die

allgemeinen Einstellungen des Routers ändern. Ändern Sie die Einstellungen wie hier beschrieben, und klicken

Sie auf die Schaltfläche Save Settings (Einstellungen speichern), um diese Änderungen zu übernehmen. Wenn

Sie die Änderungen rückgängig machen möchten, klicken Sie auf die Schaltfläche Cancel Changes (Änderungen

verwerfen).

Internet-Einrichtung

Im Abschnitt Internet Setup (Internet-Einrichtung) wird der Router für Ihre Internetverbindung konfiguriert.

Die meisten Informationen hierzu erhalten Sie von Ihrem ISP.

Internet-Verbindungstyp

Wählen Sie aus dem Dropdown-Menü den von Ihrem ISP bereitgestellten Internet-Verbindungstyp aus.

• DHCP: Standardmäßig ist der Internet-Verbindungstyp Automatic Configuration - DHCP (Automatische

Konfiguration - DHCP) für den Router ausgewählt. Behalten Sie diese Einstellung nur bei, wenn DHCP von

Ihrem ISP unterstützt wird, oder wenn Sie über eine dynamische IP-Adresse mit dem Internet verbunden sind.

• Static IP (Statische IP-Adresse): Wenn Sie für die Internetverbindung eine permanente IP-Adresse

verwenden müssen, wählen Sie die Option Static IP (Statische IP-Adresse) aus.

Internet IP Address (Internet-IP-Adresse): Hierbei handelt es sich um die IP-Adresse des Routers, vom

Standpunkt der Internetbenutzer aus gesehen. Sie erhalten die hier anzugebene IP-Adresse von Ihrem ISP.

Subnet Mask (Subnetzmaske): Hierbei handelt es sich um die Subnetzmaske des Routers, vom Standpunkt

der Internetbenutzer (einschließlich Ihres ISP) aus gesehen. Sie erhalten die Subnetzmaske von Ihrem ISP.

Gateway: Sie erhalten die Gateway-Adresse von Ihrem ISP. Bei dieser Adresse handelt es sich um die IP-

Adresse des ISP-Servers.

DNS: Sie erhalten von Ihrem ISP mindestens eine Server-IP-Adresse für das DNS (Domain Name System).

Abbildung 5-2: Registerkarte zur Einrichtung:

„Basic Setup“ (Grundlegende Einrichtung)

Abbildung 5-3: Verbindungstyp „DHCP“

Abbildung 5-4: Verbindungstyp „Statische IP-Adresse“

Kapitel 5: Konfigurieren des Wireless-G Broadband-Routers mit SRX400

Die Registerkarte „Setup“ (Einrichtung) - „Basic Setup“ (Grundlegende Einrichtung)

Wireless-G Broadband-Router mit SpeedBooster

• PPPoE: Einige ISPs mit DSL-Option verwenden PPPoE (Point-to-Point Protocol over Ethernet) zur Herstellung

von Internetverbindungen. Wenn die Verbindung mit dem Internet über eine DSL-Leitung hergestellt wird,

klären Sie mit dem ISP, ob PPPoE verwendet wird. Falls ja, wählen Sie die Option PPPoE aus.

User Name (Benutzername) und Password (Passwort): Geben Sie den Benutzernamen und das Passwort

ein, die Sie von Ihrem ISP erhalten haben.

Connect on Demand: Max Idle Time (Bei Bedarf verbinden: Max. Leerlaufzeit): Sie können den Router so

konfigurieren, dass die Internetverbindung nach einem bestimmten Zeitraum getrennt wird (maximale

Leerlaufzeit). Wenn Ihre Internetverbindung wegen Leerlaufs getrennt wurde, kann der Router mit Hilfe der

Option Connect on Demand (Bei Bedarf verbinden) Ihre Verbindung automatisch wiederherstellen, sobald

Sie erneut auf das Internet zugreifen. Klicken Sie auf die entsprechende Optionsschaltfläche, um die Option

Connect on Demand (Bei Bedarf verbinden) zu aktivieren. Geben Sie im Feld Max Idle Time (Max.

Leerlaufzeit) die Anzahl der Minuten ein, nach deren Ablauf die Internetverbindung getrennt werden soll.

Keep Alive: Redial Period (Verbindung aufrecht halten: Wahlwiederholung): Wenn Sie diese Option

auswählen, überprüft der Router regelmäßig Ihre Internetverbindung. Wenn die Verbindung getrennt wird,

stellt der Router Ihre Verbindung automatisch wieder her. Aktivieren Sie zur Verwendung dieser Option die

Optionsschaltfläche neben Keep Alive (Verbindung aufrecht halten). Im Feld Redial Period (Wahlwiederholung)

legen Sie fest, wie oft der Router Ihre Internetverbindung überprüfen soll. Standardmäßig erfolgt die

Wahlwiederholung nach 30 Sekunden.

• PPTP: PPTP (Point-to-Point Tunneling Protocol) ist ein Dienst, der nur für Verbindungen in Europa gültig ist.

Geben Sie unter Internet IP Address (Internet-IP-Adresse) einen Wert an: Hierbei handelt es sich um die IP-

Adresse des Routers, vom Standpunkt der Internetbenutzer aus gesehen. Sie erhalten die hier anzugebende

IP-Adresse von Ihrem ISP.

Subnet Mask (Subnetzmaske): Hierbei handelt es sich um die Subnetzmaske des Routers, vom Standpunkt

der Internetbenutzer (einschließlich Ihres ISP) aus gesehen. Sie erhalten die Subnetzmaske von Ihrem ISP.

Gateway: Sie erhalten die Gateway-Adresse von Ihrem ISP.

User Name (Benutzername) und Password (Passwort): Geben Sie den Benutzernamen und das Passwort

ein, die Sie von Ihrem ISP erhalten haben.

Connect on Demand: Max Idle Time (Bei Bedarf verbinden: Max. Leerlaufzeit): Sie können den Router so

konfigurieren, dass die Internetverbindung nach einem bestimmten Zeitraum getrennt wird (maximale

Leerlaufzeit). Wenn Ihre Internetverbindung wegen Leerlaufs getrennt wurde, kann der Router mit Hilfe der

Option Connect on Demand (Bei Bedarf verbinden) Ihre Verbindung automatisch wiederherstellen, sobald

Sie erneut auf das Internet zugreifen. Klicken Sie auf die entsprechende Optionsschaltfläche, um die Option

Connect on Demand (Bei Bedarf verbinden) zu aktivieren. Geben Sie im Feld Max Idle Time (Max. Leerlaufzeit)

die Anzahl der Minuten ein, nach deren Ablauf die Internetverbindung getrennt werden soll.

Keep Alive: Redial Period (Verbindung aufrecht halten: Wahlwiederholung): Wenn Sie diese Option

auswählen, überprüft der Router regelmäßig Ihre Internetverbindung. Wenn die Verbindung getrennt wird,

stellt der Router Ihre Verbindung automatisch wieder her. Aktivieren Sie zur Verwendung dieser Option die

Optionsschaltfläche neben Keep Alive (Verbindung aufrecht halten). Im Feld Redial Period (Wahlwiederholung)

legen Sie fest, wie oft der Router Ihre Internetverbindung überprüfen soll. Standardmäßig erfolgt die

Wahlwiederholung nach 30 Sekunden.

Abbildung 5-5: Verbindungstyp „PPPoE“

Abbildung 5-6: Verbindungstyp „PPTP“

Kapitel 5: Konfigurieren des Wireless-G Broadband-Routers mit SRX400

Die Registerkarte „Setup“ (Einrichtung) - „Basic Setup“ (Grundlegende Einrichtung)

Wireless-G Broadband-Router mit SpeedBooster

• Telstra Cable (Telstra-Kabel): Telstra-Kabel ist ein Dienst, der nur für Verbindungen in Australien gültig ist.

User Name (Benutzername) und Password (Passwort): Geben Sie den Benutzernamen und das Passwort

ein, die Sie von Ihrem ISP erhalten haben.

Heart Beat Server (HeartBeat-Server): Hierbei handelt es sich um die IP-Adresse des Routers, vom

Standpunkt der Internetbenutzer aus gesehen. Sie erhalten die hier anzugebende IP-Adresse von Ihrem ISP.