GYS LCD GYSMATIC 9-13 G HELMET de handleiding

Categorie
Lassysteem
Type
de handleiding

Deze handleiding is ook geschikt voor

FR 02-04 / 23-26
EN
05-07 / 23-26
DE 08-10/ 23-26
ES 11-13 / 23-26
RU 14-16 / 23-26
V3 - 19/01/17 - Ref. 043909
NL 17-19 / 23-26
IT 20-22 / 23-26
2
FR
Le masque GYSMATIC LCD 9/13 G est conforme à la directive 89/686 CEE relative aux équipements de protection individuelle. Cette conformité est établie par le respect des
normes EN 175, EN 166, EN 168 et EN 379.
Organismes notiés
Cellule : Cagoule / Ecran de garde :
N° identication : 0196 N° identication : 0196
Ce manuel est destiné à vous aider dans l’utilisation du masque GYSMATIC LCD 9/13 G, livré prêt à l’emploi. Pour votre protection, lisez attentivement ces instructions avant
l’utilisation et informez-vous convenablement auprès de votre responsable de sécurité.
AVANT UTILISATION
-Vérier le bon état général du masque, les réglages du serre-tête.
-Vérier le bon positionnement et l’état des écrans de garde et du ltre. En cas d’anomalie, veuiller procéder à sa remise en état.
-Vérier que les 4 détecteurs (9) et la cellule (8) ne soient pas obturés par des poussières ou des débris.
-Vérier que les lms protecteurs sont retirés sur les écrans de garde extérieur et intérieur.
-Vérier que le voyant rouge (1) est éteint sinon procéder au changement des batteries (7).
-Vériez si le niveau de protection correspond aux procédés de soudage employés. Pour vous aider dans votre choix, référez vous au tableau «Procédés de soudage».
FONCTIONNEMENT
Le masque opto-électronique GYSMATIC LCD 9/13 G commute instantanément de l’état clair à l’état foncé à l’amorçage de l’arc, et retourne à l’état clair lorsque l’arc s’arrête.
2 31 4 5
6
10
9
8
7 7
1. Voyant alarme faible charge
2. Potentiomètre «shade»
3. Potentiomètre «sensitivity»
4. Potentiomètre «delay»
5. Potentiomètre «soudage-Grind»
6. Écran de protection
7. Pile lithium (CR2450)
8. Celulle solaire
9. Détecteurs
10. Filtre
Potentiomètre « Shade » : La teinte foncée peut être réglée de 9 à 13 grâce au bouton intérieur.
Potentiomètre interne « Sensitivity » : Réglage de sensibilité en fonction de :
- La lumière ambiante: Hors soudage, tourner le bouton vers la position la + sensible (max), puis revenir progressivement vers « min » jusqu’à ce que la
cellule passe au clair.
- Du procédé de soudage : Position « max » pour le soudage TIG basse intensité / Position médiane pour la plupart des procédés de soudage
Potentiomètre interne « Delay » : Temps de retour à l’état clair.
Permet de retarder le temps de retour à l’état clair pour se protéger des rayonnements en n de soudure.
Voyant «Low batterie» s’allume lorsqu’il est nécessaire de changer les piles (2 piles type CR 2450, 3V)
Commutateur « WELD/GRIND » : Pour les opérations hors soudage type meulage, il est possible de déconnecter le capteur en basculant sur le mode
“GRIND”. La LED « Grind ash » clignote pour vous indiquer que le capteur est déconnecté.
ATTENTION : bien veillez à remettre le connecteur sur « WELD » avant toute opération de soudage
PRÉCAUTIONS
• Le masque est utilisable pour tous les types de procédés de soudage excepté le soudage Oxyacétylène, le soudage laser et au gaz.
• Un écran de garde extérieur et intérieur doivent être placés systématiquement de part et d’autre du ltre. L’absence d’écran peut provoquer des dommages irréversibles et
un danger pour votre sécurité.
Teinte claire 4
Teinte foncée 9-13
Dimension du ltre 114x133x9mm
Temps de réaction 0,00008 s
Alimentation Solaire + piles
Poids 580 gr
Champs de vision 100x60mm
Champs d’application MMA 5>400A / TIG 5>250A / MIG-MAG 5>500A / Grind
Garantie 1 an
Temps d’utilisation -10°C / + 55°C
Température de stockage -20°C / + 70°C
RÉGLAGE SERRE-TÊTE
Le masque GYSMATIC LCD 9/13 G est équipé d’un serre-tête qui offre 4 réglages au soudeur : largeur , hauteur (1), inclinaison (2) et ajustement longitudinal (3).
3
FR
1
3
2
ENTRETIEN / MAINTENANCE
• Date / Délai de péremption : Pas de date de péremption pour ce produit mais avant chaque utilisation l’état de votre masque GYSMATIC LCD 9/13 G doit être vérié.
• Le masque GYSMATIC LCD 9/13 G ne doit pas chuter au sol.
• Ne pas placer d’objets lourds ou d’outils sur ou dans le masque an de ne pas endommager le ltre ou les écrans de garde.
• La détérioration du ltre optoélectronique ou de son écran de garde réduit la vision et le niveau de protection. Remplacez immédiatement les éléments détériorés.
• N’utilisez aucun outil pour enlever des éléments du masque ou du ltre, ceci pouvant entraîner des dommages pouvant provoquer des blessures ou annuler la garantie.
• Nettoyer le ltre Optéo-électronique avec un coton propre ou un chiffon spécial pour objectifs.
• Nettoyer et changer régulièrement les écrans de garde.
• Nettoyer l’intérieur et l’extérieur du masque avec un détergent-désinfectant neutre.
• N’utilisez pas de solvant.
REMPLACEMENT DES ÉCRANS DE GARDE INTERNE ET EXTERNE.
1. Dévisser la vis de xation (A)
2. Remplacer l’écran interne (B) sur le ltre LCD
3. Remplacer l’écran externe (C)
4. Remettez le xateur et revisser la xation (A)
REMPLACEMENT DES PILES
Le ltre opto-électronique utilise 2 piles de 3V au lithium (CR2450). Lorsque le voyant rouge «Alarme faible charge» (1) s’allume, vous devez procéder
au changement des 2 piles.
Suivre les instructions ci-dessous pour le changement de piles :
- Positionner le curseur du cache (7) sur «cadenas ouvert»
- Tirer sur le cache et ensuite retirer la pile.
- Replacer la nouvelle pile dans son logement . La polarité « +» doit rester visible.
- Replacer le cache (7) et positionner le curseur sur «cadenas fermé».
- Procéder à la même opération pour la seconde pile.
- Les piles remplacées, le voyant «Alarme faible charge» (1) doit rester éteint.
- Il est conseillé de remplacer les deux piles, une fois par an.
AVERTISSEMENT :
- Recycler les piles lithium usagées. Les piles sont considérées en Europe comme déchets dangereux.
- Ne pas jeter dans la poubelle, à déposer uniquement dans les bacs de collecte pour piles usagées.
ATTENTION
• Cet équipement est destiné uniquement à la protection des yeux contre les rayonnements ultraviolet et infrarouge, les projections incandescentes et
étincelles provoquées lors des opérations de soudage et coupage.
• Le masque GYSMATIC LCD 9/13 G n’est pas conçu pour vous protéger contre des chocs importants ou des impacts tels que, des fragments de disques
abrasifs ou de disques de meulage, pierres et autres outils de meulage, mécanismes explosifs ou liquides corrosifs … (liste non exhaustive).
Une protection appropriée doit être utilisée lorsque ces dangers existent.
• Le bandeau du serre-tête peut éventuellement engendrer des allergies chez les personnes sensibles.
• Le ltre opto-électronique du masque GYSMATIC LCD 9/13 G n’est pas étanche et ne fonctionnera pas correctement s’il a été en contact avec de l’eau.
• Les températures d’utilisation du ltre opto-électronique sont de -10°C à +55°C.
• Les températures de stockage du masque GYSMATIC LCD 9/13 G sont de -20°C à +70°C.
ANOMALIES ET REMÈDES
Le Filtre optoélectronique ne fonctionne pas Activer la charge solaire en exposant la cellule à la lumière pendant 20 à 30 minutes – vérier et
changer les piles si nécessaire. (alarme faible charge)
Vérier que le potentiomètre est bien sur la position « soudage » (9 à 13)
Le ltre optoélectronique reste en teinte foncée quand il n’y a pas
d’arc ou quand l’arc est éteint
Vérier les détecteurs et nettoyer si nécessaire.
Ajuster la sensibilité en position basse. Si l’endroit de soudure est extrêmement lumineux, il est
recommandé de réduire le niveau de luminosité.
Commutation incontrôlée et scintillement: Le ltre bascule en teinte
claire et foncée pendant la phase de soudage
Vérier que les détecteurs soient bien dans l’axe de l’arc électrique, sans obstacle. Tourner le
réglage de sensibilité vers max.
Les cotés sont plus clairs que la zone centrale du ltre
optoélectronique
C’est une caractéristique naturelle des LCD, ce symptôme n’est pas dangereux pour les yeux.
Cependant pour un confort maximum, essayer de garder un angle de vue proche des 90°
4
FR
ÉTIQUETTE DE SÉCURITÉ
Cette étiquette est afchée à l’intérieur du masque de soudage. Il est important que l’utilisateur comprenne la signication des symboles de sécurité. Les numéros de la
liste correspondent aux numéros des images.
?
1
2
6
6.1
6.2
6.3
7
8
3
4
5
Légende :
A. Attention! Prendre garde! Il existe des dangers possibles, comme indiqué par les différents symboles.
1. Lire attentivement les instructions avant d’utiliser le matériel ou de souder.
2. Ne pas retirer l’étiquette de prévention et ne pas peindre sur cette étiquette.
3. Respecter les consignes de réglages et d’entretien du ltre, des écrans de garde, du serre-tête et de la cagoule.
4. Inspectez soigneusement le masque et son ltre UV/IR. Remplacer immédiatement les pièces usées ou endommagées. Fissurés, rayés, les verres ltrants ou les écrans
de garde réduisent sérieusement la protection. Remplacer les immédiatement pour éviter d’endommager vos yeux.
5. Attention, si le ltre UV/ IR ne se teinte pas en soudage ou en découpage, arrêter immédiatement. (Consulter la notice d’instructions)
6. Le rayonnement de l’arc peut provoquer des brûlures aux yeux et sur la peau.
6.1. Utiliser un masque de soudage avec une ltration ou une opacité correcte. Porter des vêtements de protection complets.
6.2. Le masque, le ltre et les écrans de garde ne garantissent pas une protection illimitée contre des chocs ou des impacts importants, des mécanismes explosifs ou
liquides corrosifs. Eviter le soudage ou le découpage dans ces environnements sévères.
6.3. Ne pas souder ou découper au dessus de votre tête avec ce masque.
7. Eloignez votre tête de la zone enfumée. Utilisez une ventilation forcée ou un système local d’aspiration pour éliminer les fumées.
8. Le soudage-découpage oxyacétylène, au laser ou au gaz n’est pas autorisé avec ce masque.
5
EN
The welding helmet GYSMATIC LCD 9/13 G complies with EEC directives 89/686 CEE. This conrmity is established in compliance with EN 175, EN 166, EN 168 and EN 379.
Notied bodies / organisations :
Cell : Welding hood / Protection
screen :
Identication number : 0196 Identication number : 0196
This welding helmet is delivered ready for use. For your protection, please read carrefully these instructions and consult with a qualied instructor prior to operation.
BEFORE WELDING
-Check that the welding helmet is in good condition and headband adjustment.
-Check whether the front cover lens, the front frame and lter are inserted and xed in place. In case of anomalie, please proceed to its reconditionning.
-Make sure that the 4 sensors (9) and the cell (8) are not obstructed by dust or debris.
-Make sure that the protection lms on both screens are removed.
-Make sure that the red light (1) is off, otherwise change the batteries (7).
-Check that the protection level matches your welding processes. Please refer to the following chart to help your choice (cf. welding process board)
OPERATION
The GYSMATIC LCD 9/13 G auto-darkening welding helmet switches from light to dark state when a welding arc is struck. The auto-darkening welding helmet switches back
to the light state when the arc stops.
2 31 4 5
6
10
9
8
7
7
1. Low charge leve
2. Shade control knob
3. Sensitivity control knob
4. Delay time control knob
5. Potentionmeter «Welding-Grinding»
6. LCD protection plate
7. Lithium batteries (CR2450)
8. Solar cell
9. Sensors
10. Filter
Shade potentiometer : The shade number can be set manually between Din 9 à 13. Select a shade number by the internal knob.
• Internal sensitivity potentiometer : Sensitivity adjustable according to :
- Light ambient: Without welding, turn the sensitivity setting towards «max», then turn the sensitivity setting towards «low» until lter lightens.
- Welding process: «Max» position for low amperage TIG rpocess / Medium range for most application.
• Internal delay potentionmeter: Controls the delay for the helmet to switch back to clear after welding.
Delay is designed for slower switching time to clear state to eliminate remained bright rays.
• The Low battery indicator blinks when the battery replacement is required. (2 coin type CR 2450, 3V).
• “WELD/GRIND” knob : For non-welding operation, you can switch off the lter on « Grind » mode. The Grind led will blink to conrm the lter is off.
WARNING: To be protected before welding, carefully check the switch to be on WELD mode.
PRECAUTIONS
• The welding helmet is suitable for use with virtually all welding processes except Oxy-Acetylene welding, laser welding and gas welding.
• Standard protective screens must be installed on both inside and outside surfaces of the module. Failure to use protective screens may constitute a safety hazard or result in
irreparable damage to the module.
Clear shade 4
Dark shade 9-13
Filter dimension 114x133x9mm
Reaction speed 0,00008 s
Power supply Solar + batteries
Weight 4580 gr
Field of vision 100x60mm
Applications MMA 5>400A / TIG 5>250A / MIG-MAG 5>500A / Grind
Warranty 1 year
Application temperature -10°C / + 55°C
Storage temperature -20°C / + 70°C
HEADBAND ADJUSTMENT
The GYSMATIC LCD 9/13 G is equipped with a headband which can be adjsuted in multiple ways to suit the welder: width, height (1), longitudinal inclination (3) and adjust-
ment (2).
6
EN
1
3
2
MAINTENANCE
• Expiration date: No expiration date for this product but the state of the Hermès GYSMATIC LCD 9/13 G welding helmet must be checked before each use.
The welding helmet must not fall down.
Do not put any heavy tools/objects in or on the helmet in order not to damage the lter or the protective screens.
The deterioration of the lter or its protective screen can reduce the vision eld or the protection level. Replace the damaged parts.
• Do not use any tools or other sharp objects to remove any components of lter or helmet. Doing so may damage lter or helmet preventing proper function, possibly causing
injury or cancellation of the warranty.
• Clean the lter with a clean cotton or with a special rag for lens.
• Clean and change protective screens on a regular basis.
• Clean the inside and the outside of the helmet with a neutral disinfectant product.
• Do not use any solvent.
REPLACING THE EXTERNAL AND THE INTERNAL PROTECTIVE SCREEN
1. Unscrew the lter retainer (A)
2. Replace the internal protection (B) from the LCD lter
3. Replace the external protection (C)
4. Replace and screw the lter retainer (A)
REPLACING BATTERIES
The opto-electronic lter uses 2 x 3V lithium batteries (CR2450). When the red light "Low battery alarm" (1) is on, batteries must be changed.
Follow the instructions below to change batteries:
- Position the slider on the cover (7) on "locker open"
- Pull the cover and remove the battery.
- Place a new battery in position. Polarity "+" must stay visible.
- Place the cover (7) back and position the slider on "locker closed"
- Do the same process for the other battery.
- Once the batteries have been replaced, the indicator "Low battery alarm" (1) must stay off.
- We recommend to replace the batteries once a year.
CAUTION
- Recycle used lithium batteries. In Europe, batteries are considered as dangerous waste.
- Do not throw in the bin. To drop off only in collection point for used batteries.
WARNING
• Use the welding helmet only for eye and face protection against harmful ultra violet and infrared radiation, sparks and spatter from welding.
• This product will not protect you against serious impact hazards such as, fragments of grinding wheels or abrasive discs, stones, or other grinding
tools, explosive devices or corrosive liquids (non exhaustive list). Appropriate protection must be used where these hazards exist.
• The hairband may cause allergies to sensitive people.
• The opto-electronic lter of the GYSMATIC LCD 9/13 G is not waterproof and will not work properly if it has been in contact with water.
• Application temperature of the lter is from -10°C to +55°C.
• Storage temperature of the GYSMATIC LCD 9/13 G is from -20°C to +70°C.
TROUBLESHOOTING
The optoelectronic lter does not work Activate the solar charge by exposing the cell to the light for 20 to 30 minutes -
Check and change battery if necessary. (Low charge level)
Make sure that the potentiometer is set to the «welding» position (9 to 13)
Filter stays dark after the weld arc is extinguished or when no arc is present Check and clean detectors if needed.
Adjust sensitivity knob to the lowest position. If the ambient light around the
welding area is extremely bright it is recommended to reduce the light level.
Uncontrolled switching or ickering:
Filter darkens and then lightens while the welding arc is present
Check arc sensors are not blocked from direct access to the arc light. Adjust the
sensitivity to a higher setting
Side of the lter is lighter than the center of viewing area It is a natural feature of LCD’s, this symptom is not dangerous for the eyes.
However for a maximum comfort, try to keep a viewing angle of around 90°
7
EN
SAFETY LABEL
This label is displayed inside the welding helmet. It is important that the user understands the safety symbols signication. The list numbers match image numbers.
?
1
2
6
6.1
6.2
6.3
7
8
3
4
5
Legend :
A. Warning ! Beware ! There are possible dangers as per the different symbols.
1. Read the instructions carefully before using the product or before welding.
2. Do not remove the warning label and do not paint on it.
3. Follow settings instructions and maintenance of the lter, the protective screens, the headband and the hood.
4. Inspect the helmet and the UV/IR lter carefully. Replace damaged or worn parts immediately. Cracked, scratched, lter glasses and protective screens decrease protection.
Replace them immediately to avoid damaging your eyes.
5. Warning, if the UV/IR lter does not tint whilst welding or cutting, stop immediately and consult the user manual.
6. Arc radiation can cause eyes and skin burns.
6.1. Use a welding helmet with a good ltration or opacity. Wear complete protective clothing..
6.2. The helmet, lter and protective screen do not gurantee unlimited protection against, shocks, impacts, explosions or corrosive liquid. Avoid welding or cutting in rough envi-
rionment.
6.3. Do not weld or cut above your head with this helmet.
7. Keep your head away from the smoke-lled area. Use a forced ventilation or a local aspiration system to eliminate smoke.
8. The oxyacetylene welding-cutting, laser or gas is not authorised with this helmet.
8
DE
Der GYSMATIC LCD 9/13 G Schweißhelm ist richtlinienkonform mit der europäischen Richtlinie über persönliche Schutzausrüstungen 89/686 CEE und stimmt mit den erweiter-
ten Normen EN 175, EN 166 und EN 168 überein.
Notizierte Stellen:
Zelle : Maske / Schutzschirm:
Identikationsnummer: 0196 Identikationsnummer: 0196
Der Schweißhelm wird betriebsbereit ausgeliefert. Zu Ihrem Schutz und um sicherzustellen, dass der GYSMATIC LCD 9/13 G Schweißhelm
richtig funktioniert, lesen Sie bitte die Betriebsanleitung sorgfältig durch und befragen Sie Ihren Experten für Sicherheit.
VOR DEM GEBRAUCH
- Den guten Zustand des Helmes, die Regelung des Schweibandes prüfen.
- Den korrekten Sitz und den guten Zustand der Scheiben und des Filters prüfen. Bei Fehler, überholen.
- Sicherstellen, dass die 4 Sensoren (9) und die Zelle (8) nicht mit Staub und Schmutz bedeckt sind.
- Sicherstellen, dass die Folien von den Außen- und Innenscheiben entfernt sind.
- Sicherstellen, dass die rote LED (1) nicht leuchtet. Ggf. Batterie ersetzen (7).
- Stellen Sie die richtige Abdunkelungsstufe für den Schweißprozess ein. Die passende Abdunkelungsstufe entnehmen Sie der Tabelle "Schweißverfahren".
BETRIEB
Der optoelektronische GYSMATIC LCD 9/13 G Schweißhelm schaltet bei Erkennung eines Lichtbogens selbsttätig auf Abdunkelung. Nach Schweißende wird automatisch auf
Klarsicht umgeschaltet.
2 31 4 5
6
10
9
8
7 7
1. Anzeige für geringen Batterieladestand
2. «Shade»-Regler
3. «Sensivity»-Regler
4. «Delay»-Regler
5. Drehregler «WELD/GRIND»
6. Vorsatzscheibe
7. Batterien Lithium (CR2450)
8. Solarzelle
9. Sensoren
10. Filter
Potentiometer «Shade»: mit dem internen Drehknopf können Sie die Intensität des Abdunkelns zwischen 9-13 dem Schweißprozess anpassen.
Interner «Sensitivity»-Regler: Einstellung der Empndlichkeit anhand:
- Umgebungslicht: außerhalb des Schweißzyklus, drehen Sie den Knopf bis zur maximalen Position («Max»), dann drehen Sie progressiv den Knopf nach«Min»
zurück bis die Zelle wieder hell wird.
- Schweiß-Methode: für WIG Schweißen mit niedriger Intensität, stellen Sie die Position «Max» ; für die meisten Schweißarbeiten, Mittelstellung.
Interner «Delay»-Regler:
Mit diesem Regler können Sie die Reaktionszeit einstellen.
• Die Entladung-Kontrollicht leuchtet wenn die Batterien ausgewechselt werden müssen (2 Batterien Typ CR 2450, 3 V).
Schalter «WELD/GRIND»: Bei alle Aufgaben außer Schweißarbeiten, sowie Schleifen, ist es möglich die Sensorverbindung beim Einstellen des „GRIND“
Modus zu trennen. Die LED-Anzeige „GRIND ash“ leuchtet wenn der Sensor ausgeschaltet ist.
Achten Sie darauf, den Sensor wieder auf „WELD“ anzuschließen bevor Sie schweißen.
SICHERHEITSHINWEISE
• Der GYSMATIC LCD 9/13 G Schweißhelm ist für fast alle Schweißarbeiten – mit Ausnahme von Sauerstoff-/ Acetylenschweißen, Laserschweißen und Gaslöten – geeignet.
• Vorsatzscheiben müssen sowohl auf der Innen- als auch der Außenseite des Filters montiert sein. Ein Fehlen dieser Scheiben kann zu einem Sicherheitsrisiko und zu einer
irreparablen Beschädigung der Filterkassette führen.
Hellstude 4
Dunkelstufe 9-13
Maße des Filters 114x133x9mm
Reaktionszeit 0,00008 s
Energieversorgung Solar + Batterien
Gewicht 580 g
Sichtfeld 100 x 60 mm
Einsatzbereiche MMA 5>400A / TIG 5>250A / MIG-MAG 5>500A / Grind
Garantie 1 Jahr
Betriebstemperatur -10°C / + 55°C
Lagertemperatur -20°C / + 70°C
REGELUNG DES SCHWEISSBANDES
Der GYSMATIC LCD 9/13 G ist mit einem Komfortschweißband ausgestattet, das sich auf vier verschiedene Arten anpassen lässt: Durchmesser (1), Höhe, Winkel (2)und Weite
(3).
9
DE
1
3
2
WARTUNG UND INSTANDHALTUNG
• Verfallsdatum / Verfallsfrist : Kein Verfallsdatum für dieses Produkt. Der Zustand des Helmes muss vor jedem Einsatz überprüft werden. Der GYSMATIC LCD 9/13 G
Schweißhelm darf nicht auf den Boden fallen. Stellen Sie keine schwere Gegenstände oder Werkzeuge auf oder in den Schweißhelm, damit der Sensor und die Vor-
satzscheiben nicht beschädigt werden.
Die Beschädigung des optoelektronischen Sensors oder Ihrer Scheibe beschränkt die Sicht und den Schutz. Die beschädigten Teile umgehend ersetzen.
• Benutzen Sie keine Werkzeuge oder scharfen Gegenstände, um Filter oder Helmteile zu wechseln. Sie könnten das Filtermodul und den Film beschädigen und in seiner
Funktion einschränken, womit Sie die Garantieansprüche außer Kraft setzen.
• Den optoelektronischen Sensor mit einem Baumwolltuch und einem Tuch speziell für Objektive reinigen.
• Die Scheiben regelmäßig reinigen und ersetzen.
• Innerhalb und außerhalb des Schweißhelmes mit einem neutralen Desinfektionsmittel/Detergens reinigen.
• Kein Lösemittel benutzen.
REMPLACEMENT DES ÉCRANS DE GARDE INTERNE ET EXTERNE.
1. Schrauben Sie die Fixierungsschraube (A) ab.
2. Ersetzen Sie die innere Vorsatzscheibe (B) auf dem LCD Filter
3. Ersetzen Sie die äußere Vorsatzscheibe (C)
4. Setzen Sie wieder die Fixierungsschraube (A) ein und schrauben Sie fest.
ERSETZEN DER BATTERIEN
Der optoelektronische Sensor nutzt 2 Lithium-Ionen-Batterien 3 V (CR2450). Wenn die rote LED "schwache Batterie" (1) leuchtet, sind die 2 Batterien zu ersetzen.
Beachten Sie die Anweisungen (s. unten) zum Ersetzen der Batterien:
- Drehen bis der Scheiber der Abdeckung (7) auf "offenes Vorhängeschloss" steht.
- Die Abdeckung abnehmen und danach, die Batterie entfernen.
- Die neue Batterien ins Fach einsetzen. Die Polarität "+" soll sichtbar bleiben.
- Die Abdeckung (7) erneut einsetzen und den Scheiber auf "geschlossenes Vorhängeschloss" drehen.
- Den selben Vorgang für die zweite Batterie durchführen.
- Sobald die Batterien ersetzt sind, sollte die LED "schwache Batterie" (1) nicht leuchten.
- Empfohlen ist das jährliche Ersetzen der zweiten Batterien.
ACHTUNG:
- Die Lithium-Ionen-Batterien wiederverwerten. Die Batterien sind in Europa als gefährliche Abfallmaterialen eingestuft.
- Nicht wegwerfen, nur in Aufnahmebehälter für verbrauchte Batterien deponieren.
HINWEISE UND WARNUNGEN
• Verwenden Sie den Schweißhelm ausschließlich als Augen- und Gesichtsschutz vor ultravioletter und Infrarotstrahlung, Funken und Spritzern, die bei Schweiß- und Schnei-
dearbeiten entstehen.
• Der GYSMATIC LCD 9/13 G Schweißhelm schützt Sie nicht gegen schweißbedingte Gefahren wie abspringende Schleiffragmente, Steine oder Werkzeugteile, explosive Ge-
genstände, ätzende Flüssigkeiten usw. Treffen Sie ausreichende Schutzvorkehrungen, wenn Sie in entsprechenden Gefahrenbereichen bzw. unter Risikobedingungen arbeiten.
• Das Schweißband kann bei Personen mit empndlicher Haut möglicherweise Allergien hervorrufen.
• Der optoelektronische Sensor des GYSMATIC LCD 9/13 G Schweißhelmes ist nicht wasserdicht und kann möglicherweise nicht korrekt funktionieren, nachdem er mit Wasser
in Berührung gekommen ist.
• Die Betriebstemperatur des optoelektronischen Sensor liegt zwischen -10°C und +55°C.
• Die Lagertempreratur des GYSMATIC LCD 9/13 G Schweißhelmes liegt zwischen -20°C und +70°C.
FEHLER UND LÖSUNGEN
Der optoeletronische Sensor funktioniert nicht. Setzen Sie die Solarzelle 20 bis 30 Minuten dem Sonnenlicht aus, damit sich
diese auaden kann – die Batterie prüfen und gegebenfalls wechseln (Entladung-
Kontrollicht).
Prüfen ob der Schalter auf WELD Modus eingestellt ist (9 bis 13).
Filter bleibt abgedunkelt, obwohl der Lichtbogen bereits erloschen bzw. kein
Lichtbogen vorhanden ist
Überprüfen Sie die Sensoren und reinigen Sie sie gegebenenfalls.
Stellen Sie die Lichtempndlichkeit auf einen entsprechenden niedrigeren Wert ein.
Unkontrolliertes Schalten oder Flackern :
Der Filter wechselt zu einer Dunkelstufe und Hellstufe während des Schweißens.
Achten Sie darauf, dass die Sensoren nicht vom Lichtbogen abgeschirmt sind bzw.
verdeckt werden. Stellen Sie die Lichtempndlichkeit auf einen höheren Wert ein.
Die Seiten des Filters sind heller als die Mitte des Sichtfeldes. Normales Verhalten eines LCD Filter. Dies ist für die Augen ungefährlich. Achten
Sie jedoch darauf stets den Idealwinkel von 90° zum Werkstück einzuhalten, um
maximalen Schutz beim Schweißen zu ermöglichen.
10
DE
SICHERHEITSETIKETT
Dieses Etikett bendet sich auf der Helminnenseite. Wichtig ist, dass der Anwender die Bedeutung der Sicherheitszeichen versteht. Die Nummer der Liste entsprechen den
Zeichennummern.
?
1
2
6
6.1
6.2
6.3
7
8
3
4
5
Zeichenerklärung :
A. Achtung! Bitte beachten! Mögliche Gefahren sind vorhanden, wie es mit den Zeichen abgebildet worden ist.
1. Lesen Sie sorgfältig die Anweisungen vor der Benutzung des Helmes oder vor dem Schweißen.
2. Entfernen Sie das Sicherheitsetikett nicht und bemalen Sie es nicht.
3. Beachten Sie die Anweisungen bezüglich Regelung und Wartung des Filters, der Scheiben, des Schweißbandes und der Schweissschutzhaube.
4. Überprüfen Sie sorgfältig den Zustand des Helmes und des UV/IR Filters. Ersetzen Sie sofort die abgenutzten oder beschädigten Teile. Wenn die Gläser oder Scheiben gerissen
oder beschädigt sind, ist der Schutz deutlich reduziert. Ersetzen Sie diese sofort, damit die Augen nicht geschädigt werden.
5. Achtung: Falls der UV/IR Filter beim Schweißen oder Schneiden nicht auf Abdunkelung schaltet, beenden Sie ihre Arbeit sofort. (s.Betriebsanleitung)
6. Der Lichtbogen kann zu Augen- und Hautverbrennungen führen.
6.1. Benutzen Sie einen Schweißerhelm mit einer entsprechenden Filtrierung und Opazität. Tragen Sie eine vollständige Schutzkleidung.
6.2. Der Schweißerhelm, der Filter und die Scheiben sorgen nicht für einen unbeschränkten Schutz gegen bedeutende Stöße und Schläge, explosive Gegenstände oder ätzende
Flüssigkeiten. Vermeiden Sie das Schweißen oder das Schneiden in solchen rauen Umgebungen.
6.3. Schweißen oder Schneiden Sie mit diesem Schweißerhelm nicht über Kopf.
7. Entfernen Sie Ihren Kopf vom verraucherten Bereich. Verwenden Sie eine Fremdbelüftung oder ein lokales Absaugsystem zur Entfernung der Rauches.
8. Das Sauerstoff-/ Acetylenschweißen, Laserschweißen und Gaslöten dürfen nicht mit diesem Helm durchgeführt werden.
11
ES
La máscara GYSMATIC LCD 9/13 G se ajusta a las directivas 89/686 CEE sobre los equipos de protección individual. Esta conformidad se establece por el cumplimiento de las
normas EN 175, EN 166, EN 168 y EN 379.
Organismos noticados:
Célula: Capucha / Pantalla de protección :
Nº de identicación: 0196 Nº de identicación: 0196
Este manual le ayudará a entender el uso de la máscara GYSMATIC LCD 9/13 G, la cual está lista para usarse. Lea atentamente estás instrucciones para su protección antes
de su uso e infórmese adecuadamente de la protección que necesita.
ANTES DE SU USO
-Compruebe el buen estado general de la máscara y los ajustes de la sujeción para la cabeza.
-Compruebe el buen posicionamiento de la máscara y el estado de las pantallas protectoras y del ltro. En caso de anomalía, póngalo como debe ser.
-Compruebe que los 4 detectores (9) y la célula (8) no estén obstruidos por el polvo o por restos.
-Compruebe que los lms protectores estén retirados de las pantallas de protección exterior e interior.
-Compruebe que el indicador rojo (1) esté apagado, cambie las pilas de lo contrario (7).
-Compruebe que el nivel de protección corresponde a los procedimientos de soldadura empleados. Para elegir el nivel, véase la tabla de «procesos de soldadura».
FUNCIONAMIENTO
La máscara optoelectrónica GYSMATIC LCD 9/13 G cambia de claro a oscuro con el cebado del arco, y vuelve al estado claro cuando el arco se detiene.
2 31 4 5
6
10
9
8
7 7
1. Indicador de alarma de carga débil
2. Potenciómetro «Shade»
3. Potenciómetro «Sensitivity»
4. Potenciómetro «Delay»
5. Potenciómetro «Weld-Grind» (soldadura - amoladora)
6. Pantalla de protección
7. Pila litio (CR2450)
8. Célula solar
9. Sensores
10. Filtro
Potenciómetro « Shade » : El tinte oscuro puede ajustarse de 9 a 13 con el botón exterior.
Potenciómetro interno « Sensitivity » : Ajuste de la sensibilidad en función de :
- La luz ambiente: cuando no esté soldando, ponga el botón en la posición más sensible (máx), y vaya disminuyendo progresivamente hacia « min » hasta
que la célula se aclare.
- Durante la soldadura : En « max » para la soldadura TIG de baja intensidad / Posición media para la mayoría de soldaduras
Potenciómetro interno « Delay » : tiempo de retorno al estado claro.
Permite retardar el tiempo de retorno al estado claro para protegerse de la radiación del nal de la soldadura.
Indicador «Low batterie»: se enciende cuando se necesita cambiar las pilas (2 pilas tipo CR 2450, 3V)
Conmutador « GRIND » : Para las operaciones que no son de soldadura, como el pulido, se puede desconectar los sensores con el modo “GRIND”. El
LED « Grind ash » parpadea para indicarle que el sensor está desconectado.
Cuidado: Vuelva a ponerlo en WELD antes de cualquier operación de soldadura.
PRECAUCIONES
• La máscara se puede usar para todos los tipos de procesos de soldadura excepto la soldadura con Oxyacetyleno, la soldadura láser y al gas.
• Debe haber siempre una pantalla protectora a ambos lados del ltro. La ausencia de estas pantallas puede provocar daños irreversibles y poner en peligro su seguridad.
Tinte claro 4
Tinte oscuro 9-13
Dimensiones del ltro 114x133x9mm
Tiempo de reacción 0,00008 s
Alimentación eléctrica Solar + pilas
Peso 580 gr
Campos de visión 100x60mm
Campos de aplicación MMA 5>400A / TIG 5>250A / MIG-MAG 5>500A / Grind
Garantía 1 año
Tiempo de uso -10°C / + 55°C
Temperatura de almacenaje -20°C / + 70°C
AJUSTE PARA LA CABEZA
La máscara GYSMATIC LCD 9/13 G tiene una diadema de ajuste con 4 ajustes: anchura, altura (1), inclinación (2) y ajuste longitudinal (3).
12
ES
1
3
2
MANTENIMIENTO
• Fecha / Tiempo de caducidad : No tiene fecha de caducidad, pero debe comprobar su máscara GYSMATIC LCD 9/13 G antes de cada uso.
La máscara GYSMATIC LCD 9/13 G no debe caerse al suelo.
No coloque objetos pesados o herramientas sobre o en la máscara para evitar que se dañen el ltro o las pantallas de protección.
El deterioro del ltro optoelectrónico o de las pantallas protectoras reducen la visión y el nivel de protección. Reemplace inmediatamente los elementos deteriorados.
• No utilice ninguna herramienta para quitar los elementos de la máscara o del ltro, ya que esto podría dañar el producto que provoquen heridas o la anulación de la
garantía.
• Limpie el ltro optoelectrónico con un algodón limpio o un trapo para objetos.
• Limpie y cambie de forma regular las pantallas de protección.
• Limpie el interior y el exterior de la máscara con un detergente desinfectante neutro.
• No utilice disolvente.
REEMPLAZO DE LAS PANTALLAS DE PROTECCIÓN INTERNAS Y EXTERNAS
1. Desatornillar el tornillo de jación (A)
2. Reemplace la pantalla interna (B) del ltro LCD
3. Reemplace la pantalla externa (C)
4. Vuelva a jar y a atornillar la jación (A)
REEMPLAZO DE LAS PILAS
El ltro optoelectrónico utiliza 2 pilas de 3V de litio (CR2450). Cuando el indicador rojo de "Alarma de carga débil" (1) está encendido, debe cambiar las dos pilas.
Siga las instrucciones siguiente para el cambio de las pilas:
- Ponga el cursor de la tapa (7) en "candado abierto"
- Tire de la tapa y retire la pila.
- Reemplace la nueva pila en su lugar. La polaridad « +» debe seguir estando visible.
- Vuelva a poner la tapa (7) y coloque el cursor en "candado cerrado".
- Efectúe la misma operación para la segunda pila.
- Una vez reemplazadas, el indicador "Alarma de carga débil" (1) debe quedar apagado.
- Se aconseja cambiar las dos pilas una vez al año.
Aviso:
- Recicle las pilas de litio gastadas. En Europa las pilas están consideradas como desechos peligrosos.
- No los tire a la basura. Se deben depositar en un contenedor para pilas usadas.
ATENCIÓN
• Este equipo está destinado únicamente a la protección de los ojos contra la radiación ultravioleta e infrarroja, las proyecciones incandescentes y las chispas provocadas
durante la soldadura y el corte.
• La máscara GYSMATIC LCD 9/13 G no está diseñada para protegerle contra choques importantes o impactos como los fragmentos de discos abrasivos o discos de pulido,
piedras y otras herramientas de pulido, mecanismos explosivos o líquidos corrosivos... (listado no exhaustivo). Se debe contar con una protección apropiada cuando existen
estos peligros.
• La diadema de ajuste para la cabeza puede provocar alergias a personas sensibles.
• El ltro optoelectrónico de la máscara GYSMATIC LCD 9/13 G no es impermeable y no funcionará correctamente si ha entrado en contacto con el agua.
• Las temperaturas de uso del ltro optoelectrónico son de -10°C a +55°C.
• Las temperaturas de almacenaje de la máscara GYSMATIC LCD 9/13 G son de -20°C a +70°C.
ANOMAÍAS Y SOLUCIONES
El ltro optoelectrónico no funciona Active la carga solar exponiendo la célula a la luz durante 20 a 30 minutos; compruebe y
cambie las pilas si fuese necesario. (alarma de carga débil)
Compruebe que el potenciómetro esté en posición « WELD »
El ltro optoelectrónico sigue en tinte oscuro cuando no hay arco o
cuando el arco se apaga.
Compruebe los sensores y límpielos si fuese necesario.
Ajuste la sensibilidad en posición baja. Si el lugar donde realiza la soldadura es
extremadamente luminoso, se recomienda reducir el nivel de luminosidad.
Cambio incontrolado y destellos:
El ltro cambia a tinte claro y oscuro durante la etapa de soldadura.
Compruebe que los sensores estén bien centrados al arco eléctrico, sin obstáculos. Ajuste la
sensibilidad al máximo.
Los costados son más claros que la zona central del ltro optoelectrónico. Es una característica natural de los LCD, no es peligroso para los ojos. Sin embargo, para un
mayor confort, intente guardar un ángulo de visión cercano a los 90º
13
ES
ETIQUETA DE SEGURIDAD
Esta etiqueta se encuentra en el interior de la máscara de soldadura. Es importante que el usuario comprenda el signicado de los símbolos de seguridad. Los números de la
lista corresponden a los números de las imágenes.
?
1
2
6
6.1
6.2
6.3
7
8
3
4
5
Leyenda :
A. ¡Atención! Tenga cuidado Existen varios peligros, como indicado por los diferentes símbolos.
1. Lea atentamente las instrucciones antes de utilizar el material o de soldar.
2. No retire la etiqueta de prevención y no pinte sobre ella.
3. Respete las consignas de ajuste y mantenimiento del ltro, las pantallas de protección, la sujeción y el pasamontañas.
4. Examine con cuidado la máscara y su ltro UV/IR. Reemplace inmediatamente las piezas usadas o dañadas. La protección que ofrecen los vidrios de ltro o las pantallas
de protección se ven afectadas si estos están surados o rayados. Reemplacelos inmediatamente para envitar que se dañen sus ojos.
5. Atención, si el ltro UV/IR no se tiñe al soldar o al cortar, deténgase inmediatamente. (consulte el manual de instrucciones)
6. La radiación luminosa del arco puede provocar quemaduras en los ojos y la piel.
6.1. Utilice una máscara de soldadura con un ltro o una opacidad correcta. Lleve ropa de protección completa.
6.2. La máscara, el ltro y las pantallas de protección no aseguran una protección ilimitada contra golpes o impactos importantes, mecanismos explosivos o líquidos corrosi-
vos.Evite la soldadura y el corte en estos ambientes extremos.
6.3. No suelde o corte por encima de su cabeza con esta marca.
7. Aleje su cabeza de la zona de humos. Utilice una ventilación forzada o un sistema loca de aspiración para eliminar los humos.
8. La soldadura-corte con oxyacetileno, laser o gas no se debeb realizar con esta máscara.
14
RU
Маска GYSMATIC LCD 9/13 G соответствует директиве 89/686 CEE для средств индивидуальной защиты. Это соответствие установлено соблюдением следующих
норм: EN 175, EN 166, EN 168 et EN 369.
Зарегистрированные организации:
Элемент: Шлем / Защитный экран:
Идентификационный номер: 0196 Идентификационный номер: 0196
Эта инструкция поможет вам использовать маску GYSMATIC LCD 9/13 G, готовую к использованию. Для вашей безопасности, внимательно прочтите данные
указание перед использованием, а также пройдите инструктаж у вашего руководителя по безопасности.
ПЕРЕД ИСПОЛЬЗОВАНИЕМ
-Убедитесь, что маска в хорошем состоянии и отрегулируйте обхват обруча.
-Проверьте правильное положение и состояние защитных экранов и фильтра. При наличии аномалии, приведите маску в исправное состояние.
-Убедитесь, что 4 датчика (9) и элемент (8) не покрыты пылью или налетом.
-Убедитесь, что защитные пленки с внутреннего и внешнего экрана были отклеены.
-Проверьте, что красный индикатор (1) не горит, в обратном случае поменяйте батарейку (7).
-Убедитесь, что уровень защиты соответствует применяемому методу сварки. Чтобы помочь вам в вашем выборе смотрите таблицу «Методы сварки».
ПРИНЦИП ДЕЙСТВИЯ
Оптоэлектронная маска GYSMATIC LCD 9/13 G мгновенно переходит в затемненное состояние при поджиге дуги и возвращает в исходное состояние как только дуга
затухает.
2 31 4 5
6
10
9
8
7 7
1. Индикатор «Недостаточно заряда»
2. Потенциометр «Shade»
3. Потенциометр «Sensitivity»
4. Потенциометр «Delay»
5. Потенциометр «Сварка-Шлифовка»
6. Защитный экран
7. Литиевая батарейка (CR2450)
8. Солнечный элемент
9. Датчики
10. Фильтр
Потенциометр «Shade»: Затемнение может быть отрегулировано от 9 до 13 благодаря внутренней кнопке.
Внутренний потенциометр «Sensitivity»: Настройка чувствительности в зависимости от:
- Окружающего освещения: прежде чем начать сварку, поверните кнопку в в сторону + sensible (max), затем постепенно в сторону «min» пока
элемент не посветлеет.
- В соответствии с методом сварки: Положение «max» для сварки TIG на слабых токах / Среднее положение для большинства методов сварки.
Внутренний потенциометр «Delay»: Время возвращения в светлое состояние.
Позволяет ввести задержку времени возвращения в светлое состояние, чтобы защититься против излучения в конце сварки.
Светодиод «Low batterie» загорается если необходимо заменить батарейки (2 батарейки типа CR 2450, 3В)
Переключатель «WELD/GRIND» : Для операций помимо сварки, например для шлифования, возможно отсоединить датчик, перейдя в режим
“GRIND”. Светодиод «Grind ash» мигает, предупреждая о том, что датчик отключен.
ВНИМАНИЕ: не забудьте заново вставить коннектор в режим «WELD» прежде чем начать сварочные работы
МЕРЫ ПРЕДОСТОРОЖНОСТИ
• Маска может быть использована для всех методов сварки кроме Ацетилено-кислородной, лазерной и газовой
сварки.
• Внешний и внутренний защитные экраны должны быть систематически помещены по обе стороны фильтра. Отсутствие экрана может вызвать непоправимый
ущерб и опасность для вашей безопасности.
Светлый 4
Темный 9-13
Размеры фильтра 114x133x9 мм
Время реагирования 0,00008 сек
Питание Солнечное + батарейки
Вес 580 гр
Зона обзора 100x60мм
Области применения MMA 5>400A / TIG 5>250A / MIG-MAG 5>500A / Grind
Гарантия 1 год
Температура
использования
-10°C / + 55°C
Температура хранения -20°C / + 70°C
НАСТРОЙКА ГОЛОВНОГО ОБРУЧА
Маска GYSMATIC LCD 9/13 G оснащена обручем который сварщик может подогнать по 4 параметрам: ширина, высота (1), наклон (2) и продольная посадка (3).
15
RU
1
3
2
УХОД / ОБСЛУЖИВАНИЕ
• Дата / Срок годности: Нет срока годности, но перед каждым использованием состояние вашей маски ZEUS 5-9/9-13 G должно быть проверено.
• Маска GYSMATIC LCD 9/13 G не должна падать на пол.
• Не кладите на или в маску тяжелые вещи чтобы не повредить фильтр или защитные экраны.
• Повреждение оптоэлектронного фильтра или его защитного экрана ухудшит обзор и уровень защиты. Незамедлительно заменяйте испорченные детали.
• Не пытайтесь снять с помощью инструментов детали маски или фильтра, это может привести к повреждениям, ранениям или отмене гарантии.
• Протирайте оптоэлектронный фильтр ватой или специальной тканью для объективов.
• Очищайте и регулярно меняйте защитные экраны.
• Протирайте внутреннюю и внешнюю поверхность маски с помощью нейтрального дезинфицирующего моющего средства.
• Не используйте растворитель .
ЗАМЕНА ВНУТРЕННЕГО И ВНЕШНЕГО ЗАЩИТНОГО ЭКРАНА.
1. Раскрутите зажимный винт (A)
2. Замените внутренний экран (B) жидкокристаллического
фильтра
3. Замените внешний экран (C)
4. Установите держатель и завинтите зажимный винт (A)
ЗАМЕНА БАТАРЕЕК
Оптоэлектронный фильтр работает на 2-х литиевых батарейках на 3В (CR2450). Когда загорится красный индикатор "Недостаточно заряда" (6), необходимо заменить
обе батарейки.
Для замены батареек, следуйте перечисленным ниже указаниям:
- Установите курсор крышки (5) в положение «открыть замок»
- Потяните за крышку и достаньте батарейку.
- Поместите новую батарейку в ее гнездо. Полярность «+» должна быть на видимой части батарейки.
- Поместите крышку на прежнее место (5) и установите курсор на положение «закрыть замок».
- Повторите процедуру для второй батарейки.
- После замены батареек индикатор "Недостаточно заряда" (6) не должен гореть.
- Советуется заменять обе батарейки один раз в год.
ПРЕДУПРЕЖДЕНИЕ:
- Использованные литиевые батарейки должны быть отданы на переработку. Батарейки относятся к категории опасных отходов.
- Не выбрасывать в мусорку, а поместить в специальный сборник для использованных батареек.
ВНИМАНИЕ!
• Это оборудование предназначено исключительно для защиты глаз против ультрафиолетового и инфракрасного излучения, раскаленных брызг металла и искр,
возникающих при сварке и резке.
• Маска GYSMATIC LCD 9/13 G не разработана для того, чтобы защитить вас от сильных ударов или, например, попаданий фрагментов абразивных или
шлифовальных дисков, камней и других шлифовальных инструментов, взрывоопасных механизмов или едких веществ … (список не полный). Надлежащие защитные
средства должны быть использованы, когда такая опасность существует.
• Лента обруча может вызвать аллергии у чувствительных людей.
• Оптоэлектронный фильтр маски GYSMATIC LCD 9/13 G не является водонепроницаемым, в случае контакта с водой он не будет нормально работать.
• Температурные пределы использования оптоэлектронного фильтра: от -10°C до +55°C.
• Температурные пределы хранения маски GYSMATIC LCD 9/13 G : от -20°C до +70°C.
НЕИСПРАВНОСТИ И ИХ УСТРАНЕНИЕ
Оптоэлектронный фильтр не работает Активируйте солнечный заряд, выставив элемент на свет в течение 20 - 30 минут – проверьте
и при надобности замените батарейки. (Недостаточно заряда)
Убедитесь, что потенциометр находится в положении «сварка» (от 9 до 13)
Фильтр остается темного оттенка, когда нет дуги или когда дуга
затухла
Проверьте датчики и почистите их при надобности.
Отрегулируйте чувствительность на нижнее положение. Если помещение, где вы варите,
слишком светлое, то рекомендуется снизить уровень освещенности.
Бесконтрольное переключение и мигание:
Фильтр самопроизвольно переходит в светлое и темное
состояние во время сварки
Убедитесь, что датчики находятся в направлении электрической дуги и между ними нет
препятствий. Настройте чувствительность на максимум.
Боковые части фильтра светлее, чем центральная зона Это естественное свойство экранов LCD. Этот симптом не опасен для глаз. Тем не менее, для
максимального комфорта постарайтесь сохранять угол поля зрения около 90°
16
RU
СТИКЕР ТЕХНИКИ БЕЗОПАСНОСТИ
Этот стикер находится внутри сварочной маски. Очень важно, чтобы пользователь знал значение символов техники безопасности. Номера в списке соответствуют
номерам картинок.
?
1
2
6
6.1
6.2
6.3
7
8
3
4
5
Легенда :
A. Внимание! Предупреждаем! Существует различные вероятности риска, как указано на символах.
1. Внимательно прочитайте инструкции перед использованием инструмента или сваркой.
2. Не снимать предупреждающий стикер и не закрашивать его.
3. Соблюдайте указания по настройке и уходу за фильтром, защитными экранами, обруча и шлема.
4. Внимательно проверяйте маску и ее фильтр ИК/УФ . Немедленно заменяйте изношенные или поврежденные детали. Потресканные, поцарапанные фильтрующие
стекла и защитные экраны значительное снижают уровень защиты. Немедленно замените их чтобы не повредить глаза.
5. Внимание! Если фильтр ИК/УФ не затемняется при сварке или резке немедленно остановитесь. (Посмотрите в инструкции по использованию)
6. Излучения дуги могут обжечь глаза и кожу.
6.1. Используйте сварочную маску с фильтрацией или с соответствующим затемнением. Носите защитную одежду в полном составе.
6.2. Маска, фильтр и защитные экраны не гарантируют стопроцентную защиту от сильных ударов, взрывных механизмов или коррозийных жидкостей. Не проводите
сварочных работ и работ по резке в таких условиях.
6.3. Не варите и не режьте над головой с этой маской.
7. Держите голову на расстоянии от задымленной зоны. Используйте принудительную вентиляцию или систему локальной вытяжки для удаления дыма.
8. Оксиацетиленовая, лазерная или газовая сварка-резка не разрешены для этой маски.
17
NL
De lashelm LCD GYSMATIC 9-13 is vervaardigd overeenkomstig de richtlijnen 89/686 EC. Deze overeenkomst is opgesteld volgens de EN 379 en EN 175 normen.
Genoticeerde instanties :
Cel : Kap / Spatglas :
Identicatie nummer : 0196 Identicatie nummer : 0196
Deze handleiding is bedoeld om u te helpen bij gebruik van de opto-elektronische lashelm LCD GYSMATIC 9-13, die klaar is voor gebruik. Lees, met het oog op uw vei-
ligheid, a.u.b aandachtig deze gebruiksaanwijzing door en laat u goed informeren door uw veiligheidsmanager.
VOOR GEBRUIK
-Vérier le bon état général du masque, les réglages du serre-tête.
-Vérier le bon positionnement et l’état des écrans de garde et du ltre. En cas d’anomalie, veuiller procéder à sa remise en état.
-Vérier que les 4 détecteurs (9) et la cellule (8) ne soient pas obturés par des poussières ou des débris.
-Vérier que les lms protecteurs sont retirés sur les écrans de garde extérieur et intérieur.
-Vérier que le voyant rouge (1) est éteint sinon procéder au changement des batteries (7).
-Vériez si le niveau de protection correspond aux procédés de soudage employés. Pour vous aider dans votre choix, référez vous au tableau «Procédés de soudage».
WERKING
Bij boogontsluiting schakelt de opto-elektronische lashelm LCD GYSMATIC 9-13 direct van de heldere naar de donkere tint. Hij schakelt terug naar de heldere tint bij afwe-
zigheid van de lasboog.
2 31 4 5
6
10
9
8
7 7
1. Laag laad niveau alarm lampje
2. Draaiknop «shade»
3. Draaiknop «sensitivity»
4. Draaiknop «dela
5. Draaiknop «lassen-Grind»
6. Spatglas
7. Lithium batterij (CR2450)
8. Zonnecel
9. Detectoren
10. Filter
Draaiknop «Shade» : Met de knop aan de binnenkant kunt u de donkere tint van 9 tot 13 instellen.
• Interne draaiknop «Sensitivity»: Regelt de gevoeligheid afhankelijk van:
- Licht in de lasruimte : Draai, voor of na het lasproces, de knop richting + (max gevoeligheid), draai daarna geleidelijk terug richting «min» tot de lens helder
wordt.
-De gebruikte lastechnieken: Positie «max» voor TIG lassen met lage intensiteit / Midden positie voor de meeste lastechnieken.
• Interne draaiknop «Delay»: Benodigde tijd om terug te keren op heldere tint.
Vertraagt de terugkeer naar een helderder niveau en biedt zo een betere bescherming tegen de lichtstraling aan het einde van het lasprocedure.
• Het lampje «Low Batterie» gaat aan als de batterijen vervangen moeten worden (2 batterijen type CR 2450, 3V)
• Schakelaar «WELD/GRIND»: Voor ander gebruik dan lassen zoals slijpen, is het mogelijk om de sensor uit te zetten en naar de mode «GRIND» te
schakelen. Het ledlampje «Grind ash» knippert om aan te geven dat de sensor afgekoppeld is.
WAARSCHUWING: Voor u begint met lassen, zet de schakelaar terug op «WELD».
VOORZORGSMAATREGELEN
• Het masker is geschikt voor alle lastechnieken behalve autogeen lassen, laserlassen of spuitpistool.
• Een extern en intern spatglas dienen systematisch geplaatst te worden aan beide kanten van de lter. Afwezigheid van spatglas kan ernstig en blijvend letsel veroorzaken
en een gevaar vormen voor uw veiligheid.
Heldere tint
4
Donkere tint
9-13
Afmetingen van de lter
114x133x9mm
Reactietijd
0,00008 s
Stroomvoorziening Zonnecel + batterijen
Gewicht
580 gr
Gezichtsveld
100x60mm
Te gebruiken voor
MMA 5>400A / TIG 5>250A / MIG-MAG 5>500A / slijpen
Garantie
1 jaar
Gebruikstemperatuur
-10°C / + 55°C
Bewaartemperatuur
-20°C / + 70°C
INSTELLING HOOFDBAND
De LCD GYSMATIC 9-13 lashelm is uitgerust met een hoofdband die aan de lasser 4 instellingen biedt : breedte, hoogte (1), kantelhoek (2) en verstelling in lengterichting (3).
18
NL
1
3
2
ONDERHOUD
• Vervaldatum : Er bestaat geen vervaldatum voor dit product, maar de staat van uw LCD GYSMATIC 9-13 masker moet voor elk gebruik gecontroleerd worden.
De LCD GYSMATIC 9-13 lashelm mag niet op de grond vallen.
Plaats geen zware voorwerpen of gereedschappen op of in de lashelm om het lter of het spatglas niet te beschadigen.
Beschadiging van het lter of de lens reduceert het gezichtsvermogen en het beschermingsniveau. Vervang onmiddellijk de beschadigde onderdelen.
• Gebruik nooit een gereedschap om de onderdelen van helm of lter weg te halen. Dit kan tot beschadigingen leiden die letsels kunnen veroorzaken en de garantie annuleren.
• Reinig het opto-electronisch lter met een schone katoen of een speciale lenzen doek.
• Regelmatig de spatglas reinigen en vervangen.
• Reinig de binnen- en de buitenkant van de lashelm met een neutraal reinigings-ontsmettings middel.
• Gebruik geen oplosmiddel.
VERVANGEN VAN HET INTERNE / EXTERNE SPATGLAS
1. Bevestigingsschroef losschroeven (A)
2. Vervang het interne spatglas (B) op het LCD lter
3. Vervang het externe spatglas (C)
4. Bevestigingsschroef weer vastdraaien (A)
VERVANGEN VAN BATTERIJEN
2 3V lithium batterijen (CR2450) zijn nodig voor het opto-electronisch lter. Indien het rode «laag laadniveau alarm» lampje (1) brandt, dient u de 2 batterijen te vervangen.
Volg de onderstaande instructies voor het vervangen van de batterijen:
- Verwijder de cel van de lashelm.
- Trek het batterijklepje open aan de onderkant van de cel.
- Plaats de nieuwe batterij. De «+» polariteit moet zichtbaar zijn.
- Plaats het batterijklepje terug
- Voer dezelfde handeling voor de tweede batterij.
- Na het vervangen van de batterijen, dient het «laag laadniveau alarm» lampje (1) uit te zijn.
- Het wordt aanbevolen om beide batterijen een keer per jaar te vervangen.
WAARSCHUWING:
- De gebruikte lithiumbatterijen zijn recycleerbaar. Deze batterijen worden beschouwd als gevaarlijk afval in Europa.
- Niet weggooien met het huishoudelijk afval, maar in verzamelbak voor lege batterijen werpen.
LET OP
• Deze uitrusting is uitsluitend bedoeld voor bescherming van de ogen tegen ultraviolette en infrarode straling, wegspringende scherfjes en vonken die bij het lassen of snijden
voorkomen.
De lashelm LCD GYSMATIC 9-13 is niet geschikt als bescherming tegen zware schokken of impact van slijpschijven, stenen, explosieve of vloeibare corrosieve middelen...
(onvolledige lijst). Een adequate bescherming dient gebruikt te worden bij aanwezigheid van deze gevaren.
• De hoofdband kan allergische reacties veroorzaken bij hiervoor gevoelige personen.
• De opto-elektronische LCD GYSMATIC 9-13 lter masker is niet waterdicht en zal niet goed functioneren als het in contact met water is geweest.
• Gebruikstemperatuur van opto-elektronische lter is van -5 ° C tot + 55 ° C
• De opslagtemperatuur van LCD GYSMATIC 9-13 masker is van -20 ° C tot + 70 ° C
AFWIJKINGEN EN OPLOSSINGEN
Het lter werkt niet
Activeer de zonnecel door deze gedurende 20 tot 30 minuten aan het licht bloot te stellen -
controleer en vervang de batterijen indien nodig. (low battery lampje)
Controleer of de schakelaar op "WELD" staat.
Het lter blijft donker bij afwezigheid van de vlamboog
Controleer de detectoren et maak deze indien nodig schoon.
Stel in op lage gevoeligheid. Bij een zeer helder verlichte lasruimte wordt geadviseerd om de
helderheidsgraad lager in te stellen.
Ongecontroleerde schakeling en ikkering:
De lter schakelt van heldere naar donkere tint tijdens het lassen
Controleer of de detectoren zonder belemmeringen in de as van vlamboog staan. Draai de
gevoeligheidsknop op max.
De zijkanten zijn helderder dan de centrale zone van de lter
Dit is een natuurlijke eigenschap van de LCD, dit symptoom is niet gevaarlijk voor de ogen. Houd
echter voor maximaal comfort een hoek van 90° aan.
19
NL
VEILIGHEIDSLABEL
Dit label wordt weergegeven aan de binnenkant van de lashelm. Het is belangrijk dat de gebruiker de betekenis van veiligheidssymbolen begrijpt. De nummers van de lijst
corresponderen met de nummers van de afbeeldingen.
?
1
2
6
6.1
6.2
6.3
7
8
3
4
5
Legenda :
A. Let op! Pas op! Er bestaan potentiële gevaren, zoals aangegeven door de verschillende symbolen.
1. Lees aandachtig de instructies door voor het gebruik van deze uitrusting of het lassen.
2. Het waarschuwingslabel niet verwijderen en er niet overheen schilderen.
3. Volg nauwkeurig de instructies op voor het instellen en het onderhoud van het lter, de schermen, de hoofdband en de bivakmuts.
4. Inspecteer voorzichtig en nauwkeurig de lashelm en het UV / IR-lter. Vervang onmiddellijk versleten of beschadigde onderdelen. Gebarsten of bekraste lterglazen of
schermen verminderen beduidend de bescherming . Vervang ze onmiddellijk om schade aan uw ogen te voorkomen.
5. Waarschuwing : indien de UV-lter / IR is niet donker wordt tijdens het lassen of snijden, onmiddellijk stoppen. (Raadpleeg de handleiding)
6. De straling van de lasboog kan ogen verbranden en verwondingen aan de huid veroorzaken.
6.1. Gebruik een lashelm met de juiste ltratie of bescherming. Draag volledig beschermende kleding.
6.2. De lashelm, het lter en de schermen kunnen geen onbeperkte bescherming garanderen tegen schokken of zware stoten, explosieve mechanismen of corrosieve
vloeistoffen . Vermijd het lassen of snijden in ruwe of niet geschikte omgevingen.
6.3. Niet lassen of snijden boven uw hoofd met deze lashelm.
7. Blijf met uw hoofd ver van de rook zone. Gebruik een constante ventilatie of een plaatselijk afzuigsysteem voor het verwijderen van de rook.
8. Autogeen lassen of snijden met deze lashelm is niet toegestaan.
20
IT
La maschera GYSMATIC LCD 9/13 G è conforme alla direttiva 89/686 CEE relativa alle attrezzature di protezione individuale. Questa conformità è stabilita dal rispetto delle
norme EN 175, EN 166, EN 168 e EN 379.
Enti noticati
Cellula : Casco / Schermo iniziale :
N° identicazione: 0196 N° identicazione: 0196
Questo manuale serve ad aiutarvi nell’utilizzo della maschera GYSMATIC LCD 9/13 G, fornita pronta all’uso. Per la vostra protezione, leggete attentamente queste istruzioni
prima dell’uso e informatevi correttamente dal vostro responsabile della sicurezza.
PRIMA DELL’USO
-Vericare il buono stato generale della maschera, le regolazioni della crociera.
-Vericare il buon posizionamento e lo stato degli schermi di protezione e del ltro. In caso di anomalia, procedere alla sua rimessa in buono stato.
-Vericare che i 4 rilevatori (9) e la cellula (8) non siano otturati da polveri o da detriti.
-Vericare che le pellicole protettive vengano rimosse dagli schermi di protezione esterna ed interna.
-Vericare che la spia rossa (1) sia spenta, altrimenti procedere al cambio delle batterie (7).
-Vericate se il livello di protezione corrisponde ai metodi di saldatura impiegati. Per aiutarvi nella vostra scelta, basatevi sulla tabella «Metodi di saldatura».
FUNZIONAMENTO
La maschera optoelettronica GYSMATIC LCD 9/13 G cambia istantaneamente dallo stato chiaro a quello scuro l’innesco dell’arco, e ritorna allo stato chiaro quando l’arco si
spegne.
2 31 4 5
6
10
9
8
7 7
1. Spia allarme carica debole
2. Potenziometro «shade» tonalità
3. Potenziometro «sensitivity» sensibilità
4. Potenziometro «Delay» ritardo
5. Potenziometro «saldatura-molatura»
Schermo di protezione
7. Pila litio (CR2450)
8. Cellula solare
9. Rilevatori
10. Filtro
• Potenziometro « Shade » : La tinta scura può essere regolata da 9 a 13 grazie ad un pulsante interno.
• Potenziometro interno « Sensitivity » : Regolazione di sensibilità in funzione di :
- luce ambiente : In assenza di saldatura, tenere il bottone sulla posizione + sensible (max), poi ritornare progressivamente verso il « min » no a quando la
cellula passa al chiaro.
- Del procedimento di saldatura : Posizione « max » per la saldatura TIG bassa intensità / Posizione media per la maggior parte dei procedimenti di saldatura
• Potenziometro interno « Delay » : Tempo di ritorno allo stato chiaro.
Permette di ritardare il tempo di ritorno allo stato chiaro per proteggersi dalle radiazioni al termine della saldatura.
• Spia «batteria bassa» si accende quando è necessario sostituire le batterie (2 pile tipo CR 2450, 3V)
• Commutatore « WELD/GRIND » : « saldatura/molatura » : Per le operazioni diverse dalla saldatura tipo molatura, è possibile scollegare il sensore
passando alla modalità “GRIND” molatura. Il LED «Grind ash» lampeggia per indicarvi che il rilevatore è disconnesso.
ATTENZIONE : fate attenzione a riposizionare il connettore su « saldatura » prima di qualsiasi operazione di saldatura.
PRECAUZIONI
• La maschera è utilizzabile per tutti i tipi di saldatura eccetto la saldatura ossiacetilenica, la saldatura laser e a gas.
• Uno schermo di protezione esterno e interno deve essere posizionato sistematicamente da una parte e dall’altra del ltro. L’assenza dello schermo può causare dei danni
irreversibili e un pericolo per la vostra sicurezza.
Tinta chiara 4
Tinta scura sept-13
Dimensione del ltro 114x133x9mm
Tempo di reazione 0,00008 s
Alimentazione Solare + pile
Peso 580 gr
Campo visivo 100x60mm
Campo di applicazione MMA 5>400A / TIG 5>250A / MIG-MAG 5>500A / Molatura
Garanzia 1 anno
Tempo di utilizzo -10°C / + 55°C
Temperatura di stoccaggio -20°C / + 70°C
REGOLAZIONE CROCIERA
La maschera GYSMATIC LCD 9/13 G è dotata di un elastico che offre 4 regolazioni al saldatore : larghezza, altezza (1), inclinazione (2) e regolazione longitudinale (3)
21
IT
1
3
2
MANUTENZIONE
• Controllare frequentemente la vostra maschera GYSMATIC LCD 9/13 G.
• La maschera GYSMATIC LCD 9/13 G non deve cadere al suolo.
• Non posizionare oggetti sporchi o attrezzi sopra o all’interno della maschera al ne di non danneggiare il ltro o gli schermi di protezione.
• Il deterioramento del ltro optoelettronico o del suo schermo di sicurezza riduce la visione e il livello di protezione. Sostituire immediatamente gli elementi deteriorati.
• Non utilizzate nessuno strumento per togliere degli elementi dalla maschera o dal ltro, ciò può causare dei danni che possono provocare ferite o annullare la garanzia.
• Pulire il ltro optoelettronico con del cotone appropriato o con un panno speciale per oggettistica.
• Pulire e cambiare periodicamente gli schermi di protezione.
• Pulire l’interno e l’esterno della maschera con un detergente-disinfettante neutro.
• Non utilizzare solventi.
SOSTITUZIONE DEGLI SCHERMI DI PROTEZIONE INTERNA ED ESTERNA.
1. Allentare la vite di ssaggio (A)
2. Sostituire lo schermo interno (B) sul ltro LCD
3. Sostituire lo schermo esterno (C)
4. Rimettete il ssatore e riavvitate il ssaggio (A)
SOSTITUZIONE DELLE PILE
Il ltro optoelettrico utilizza 2 pile da 3V al litio (CR2450). Quando la spia rossa «allarme carica debole» (1) si accende, dovete sostituire le 2 pile.
Seguire le istruzioni qui in basso per cambiare le pile :
- Posizionare il cursore del coperchio (7) su «lucchetto aperto»
- Sollevare il coperchio e togliere la pila.
- Mettere la nuova pila nella sua posizione. La polarità « +» deve restare visibile.
- Chiudere il coperchio (7) e posizionare il cursore su «lucchetto chiuso».
- Procedere allo stesso modo per sostituire la seconda pila.
- Dopo la sostituzione delle pile, la spia «allarme carica debole»(1) deve spegnersi.
- Si consiglia di sostituire le due pile una volta all’anno.
AVVERTENZE :
- Riciclare le pile al litio consumate. In Europa le pile sono considerate come riuti pericolosi.
- Non gettare nei riuti, da smaltire unicamente nei contenitori per la raccolta delle pile consumate.
ATTENZIONE
QUESTA ATTREZZATURA È DESTINATA SOLAMENTE ALLA PROTEZIONE DEGLI OCCHI DALLE RADIAZIONI ULTRAVIOLETTE E INFRAROSSI, DALLE
PROIEZIONI INCANDESCENTI E DALLE SCINTILLE PROVOCATE DURANTE LE OPERAZIONI DI SALDATURA E DI TAGLIO.
LA MASCHERA GYSMATIC LCD 9/13 G NON È PROGETTATA PER PROTEGGERVI CONTRO DELLE SCOSSE SIGNIFICATIVE O DEGLI IMPATTI QUALI DEI
FRAMMENTI DEI DISCHI ABRASIVI O DEI DISCHI DI MOLATURA, SCHEGGE E ALTRI STRUMENTI MOLATURA, DISPOSITIVI ESPLOSIVI O LIQUIDI
CORROSIVI ... (ELENCO NON ESAUSTIVO).
SE SUSSISTONO QUESTI PERICOLI, DEVE ESSERE UTILIZZATA UNA APPROPRIATA PROTEZIONE.
• LA FASCIA DELLA CROCIERA POTREBBE PROVOCARE DELLE ALLERGIE ALLE PERSONE SENSIBILI.
IL FILO OPTOELETTRICO DELLA MASCHERA GYSMATIC LCD 9/13 G NON È IMPERMEABILE E NON FUNZIONERÀ CORRETTAMENTE SE È STATO A
CONTATTO CON DELL’ACQUA.
• LE TEMPERATURE DI UTILIZZO DEL FILTRO OPTOELETTRICO VANNO DA -10°C A +55°C.
• LE TEMPERATURE DI STOCCAGGIO DELLA MASCHERA GYSMATIC LCD 9/13 G VANNO DA -20°C A +70°C.
ANOMALIE E RIMEDI
Il ltro optoelettronico non funziona Attivare la ricarica solare esponendo la cellula alla luce per 20 - 30 minuti – controllare e cambiare
le pile se necessario. (allarme carica debole)
Controllare che il potenziomentro sia posizionato su « saldatura » (9 a 13).
Il ltro optoelettronico rimane in tinta scura quando non c'è arco o
quando l'arco si spegne
Controllare i rilevatori e pulire se necessario.
Regolare la sensibilità nella posizione bassa. Se il luogo della saldatura è estremamente luminoso,
si consiglia di ridurre il livello di luminosità.
Commutazione incontrollata e scintillio: Il ltro passa sulla tinta chiara
e scura durante la fase di saldatura
Vericare che i rilevatori siano posizionati bene nell'asse dell'arco elettrico, senza ostacoli. Ruotare
la regolazione di sensibilità verso il massimo.
I lati sono più chiari della zona centrale del ltro optoelettronico C'è una caratteristica naturale degli LCD, questo sintomo non è pericoloso per gli occhi. Tuttavia
per un massimo confort, cercate di mantenere un angolo di visibiltà vicino a 90°
22
IT
ETICHETTA DI SICUREZZA
Questa etichetta è apposta all’interno della maschera di saldatura. È importante che l’utente capisca il signicato dei simboli di sicurezza. I numeri della lista
corrispondono ai numeri delle immagini.
?
1
2
6
6.1
6.2
6.3
7
8
3
4
5
Legenda:
A. Attenzione! Fare attenzione! Esistono pericoli possibili, come indicato dai differenti simboli.
1. Leggere attentamente le istruzioni prima di usare il materiale o prima di saldare.
2. Non ritirare l’etichetta di prevenzione e non dipingere sull’etichetta.
3. Rispettare le istruzioni di regolazione e di manutenzione del ltro, degli schermi, della fascia regolabile e del passamontagna.
4. Ispezionare accuratamente la maschera e il suo vetro UV/IR. Sostituire immediatamente le parti usate o danneggiate. Se fessurati o rigati i vetri di protezione o gli schermi
hanno il livello di protezione seriamente ridotto. Sostituire immediatamente per evitare di danneggiare gli occhi.
5. Attenzione, se il ltro UV/ IR non si oscura in saldatura o taglio, fermarsi immediatamente. (Consultare il manuale d’uso)
6. Lirradiazione dell’arco può provocare bruciature agli occhi e sulla pelle.
6.1. Usare una maschera di saldatura con ltro e opacità adatti e corretti.. Portare vestiti di protezione completi.
6.2. La maschera Le masque, le ltre et les écrans de garde ne garantissent pas une protection illimitée contre des chocs ou des impacts importants, des mécanismes explo-
sifs ou liquides corrosifs. Evitare la saldatura o il taglio in ambienti difcili.
6.3. Non saldare o tagliare al di sopra della testa con questa maschera.
7. Allontanare la testa dalle zone fumose. Usare la ventilazione forzata o un sistema locale di aspirazione per eliminare i fumi.
8. La saldatura-taglio ossiacetilene, laser o gas non è autorizzata con questa maschera.
23
GYSMATIC 9-13
MARQUAGE DU FILTRE / FILTER MARKING / FILTERKENNZEICHNUNG / MARCADO DEL FILTRO / МАРКИРОВКА ФИЛЬТРА /
MARCATURA DEL FILTRO
Chaque ltre optoélectronique possède un marquage conforme à la norme EN 379/ Each optoelectronic lter is stamped in accordance
with standard EN 379/ Beide optoelektronischen Filter haben eine Kennzeichung richtlinienkonform mit der Norm EN 379./ Cada ltro op-
toelectrónico posee un marcado conforme a la norma EN 379/ Каждый оптоэлектронный фильтр отмечен маркировкой соответствия
норме EN 379 / Ogni ltro optoelettronico ha una marcatura conforme alla norma EN 379
4 9 13 X 1 1 1 2 379
FR Numéro d’échelon à l’état clair
EN Light shade number
DE Hellstufe
ES Número de grado al estado claro
RU Номер светлого оттенка
IT Livelli dello stato di chiaro
NL Niveaunummer bij heldere tint
FR Numéro d’échelon à l’état foncé le plus clair
EN Clear dark shade number
DE Hellere Dunkelstufe
ES Número de grado al estado oscuro más claro
RU Номер самого светлого затемнения
IT Livelli dello stato di oscuramento più chiaro
NL Helderste niveau nummer bij donkere tint
FR Numéro d’échelon à l’état foncé
EN Dark shade number
DE Dunkelstufe
ES Número de grado al estado oscuro
RU Номер темного оттенка
IT Livelli allo stato si oscuramento
NL Niveau nummer bij donkere tint
FR Identication du fabricant
EN Manufacturer identication
DE Kennung des Herstellers
ES Identicación del fabricante
RU Маркировка производителя
IT Identicazione del fabbricante
NL Identicatie van de fabrikant
FR Classe optique
EN Optical class
DE Optische Klasse
ES Clase óptica
RU Оптический класс
IT Classe ottica
NL Optische klasse
FR Classe de diffusion de la lumière
EN Diffusion of light class
DE Streulichtklasse
ES Clase de difusión de la luz
RU Класс рассеивания света
IT Classe di diffusione della luce
NL Lichtdiffusie klasse
FR Classe de variation du facteur de transmission dans le visible
EN Variations in Luminous transmittance class
DE Homogenitätsklasse
ES Clase de variación del factor de transmisión en el visible
RU Класс колебания коэффициента пропускания света в видимом
IT Classe di variazione del coefciente del passaggio al campo di visibilità/schiarimento
NL Lichtdoorlaadbaardheidsklasse
FR Dépendance angulaire du facteur de transmission de la lumière
EN Angle dependence of luminous transmittance class (optional)
DE Winkeleigenschaft
ES Dependencia angular del factor de transmisión de la luz
RU Угловая зависимость коэффициента пропускания света
IT Condizionamento del coefciente di passaggio al campo di visibilità/schiarimento in funzione dall’angolazione
NL Hoekafhankelijkheidsklasse
FR Numéro de la présente norme
EN Number of standard
DE Normung
ES Número de la presente norma
RU Номер нормы
IT Numero della presente norma
NL Normnummer
24
GYSMATIC 9-13
PROCÉDÉ DE SOUDAGE / WELDING PROCESS / SCHWEISSMETHODEN / PROCESO DE SOLDADURA / МЕТОД СВАРКИ / PROCEDI-
MENTO DI SALDATURA
Procédé de soudage / Welding process / Schweißmethoden / proceso de soldadura / метод сварки / procedimento di saldatura
FR
Intensité courant Electrodes enrobées MAG TIG MIG métaux lourd MIG alliages légers Gougeage arc air Coupage plasma
Soudage au jet
plasma
EN
current intensity Coated electrodes MAG TIG heavy metals light alloys arc air gouging plasma cutting plasma welding
DE
Stromstärke Umhüllte Elektroden E-Hand WIG MIG-Stahlschweißen MIG Aluschweißen
Thermisches
Abschmelzen
Plasma-Schneiden sPlasmaschweißen
ES
intensidad de
corriente
Electrodos revestidos MAG TIG MIG metales pesados MIG metales ligeros
ranurado con arco
de aire
corte de plasma
soldadura con chorro
de plasma
RU
сила тока
электроды с
обмазкой
МАГ ТИГ
сварка МИГ
тяжелых металлов
сварка МИГ легких
сплавов
воздушно-дуговая
строжка
плазменная резка плазменная сварка
IT
Intensità corrente Elettrodo rivestito MAG TIG MIG metalli pesanti MIG leghe leggere
Scriccatura ad arco
e aria
Taglio plasma
Saldatura a getto di
plasma
NL
Stroomsterkte Beklede elektroden MAG TIG MIG zware metalen
MIG lichte verbin-
dingen
Arc-air gutsen Plasma snijden Plasma lassen
5
8
8
8
9
10
10
9
4
6
5
10
15
6
30
9
40
9
7
60
8
70
10
10
10
100
9
125
11
11
10
10
10
150
11
11
11
175
12
11
11 12
11
200
12
12
225
12
12
13
250
12 13 12
275
300
13
13
13
350
13 14
400
13 14
450
14
14
15
500
600
14
PIÈCES DÉTACHÉES / PARTS LIST / ERSATZTEILE / REPUESTOS / ЗАПАСНЫЕ ЧАСТИ / PARTI DI RICAMBIO
FR EN DE ES RU IT NL
1
Écran de garde
extérieur
Outer protection
lens
Äußere
Vorsatzscheibe
Pantalla de
guardia exterior
Внешний
защитный экран
Schermo di
protezione
esterna
Externe
beschermlens
2 Filtre Filter Filter Filtro Фильтр Filtro Filter
3
Écran de garde
intérieur
Inner protection
lens
Innere
Vorsatzscheibe
Pantalla de
guardia interior
Внутренний
защитный экран
Schermo di
protezione interna
Interne
beschermlens
4 Serre-tête Headgear Stimband Cinta Обруч Crociera Hoofdband
5
Bandeau
anti-transpirant
Anti-perspirant
headband
Schweißband
Cinta anti
transpirante
Лента для пота
fascia anti-
traspirante
Anti-transpiratie
hoofdband
1
2 3
4
5
Ref. 043466
114 x 133
(x10)
Ref. 043893
106 x 66
(x10)
Ref. 043886
25
GYSMATIC 9-13
Die Garantie ist ab Kaufdatum 1 Jahr gültig.
Sollten Sie einen Artikel als fehlerhaft zurückgeben, senden Sie die Ware (mit der Rücksendung verbundene Kosten und Gefahren sind
vom Kunden zu tragen) an Ihren Lieferant zurück mit:
• dem Kaufbeleg mit Kaufdatum (der Kassenbon, die Rechnung…)
• dem nachfolgenden Brief zur Erläuterung des Fehlers.
Nach Ablauf der Gewährleistungsfrist :
Nach der Annahme des Kostenvoranschlags durch den Kunden erledigt unser Kundendienst die Reparatur.
DIE GARANTIE ERSTRECKT SICH NICHT AUF FOLGENDES:
- Spritzspuren: Schweißen ohne Schutzscheibe (Vorsatzscheibe)
- die elektrooptische Zelle ist geöffnet
- die Zelle ist beschädigt
- der Garantieanspruch ist abgelaufen
- Transportschaden
- normalen Verschleiß von Teilen
ANMERKUNGEN ZUM FEHLER:
 keine Abdunkelung während der Schweißarbeiten
 Veränderung der Abdunkelung während der Schweißarbeiten
 Flüssigkristallfehler
 Intermittierende Fehler
 Sonstiges
Schweiß-Methode
Stromstärke
Certicat de garantie FRANCE
Valable 1 an à compter de la date d’achat.
à remplir par le vendeur :
Référence du produit :
Date d’achat :
Nom de l’acheteur :
Conditions hors garantie :
- Présence de grattons : travail sans vitre de protection (écran de garde)
- Verre cassée
- Période de garantie expirée
- Avarie due au transport
Vos remarques :
Perd la teinte en cours de travail
Modie la teinte en cours de travail
Panne intermittente
Autres ...
Méthode de soudure :
Ampérage :
Après l’année de garantie, notre SAV assure les réparations après acceptation d’un devis.
Cachet du vendeur :
ATTENTION !
Nous vous rappelons que nous n’acceptons pas
les ports dûs, en revanche le retour des appareils
réparés sera pris en charge par notre société.
GYS «SAV»
134 boulevard des Loges - BP 4159
53941 Saint-Berthevin cedex
Fax SAV : 02 43 01 23 75
Garantieschein
GYS «KD»
Professor-Wieler-Straße 11
52070 Aachen
Fax KD: 0241-189-23-71-9
26
GYSMATIC 9-13
NOTES
1 / 1

GYS LCD GYSMATIC 9-13 G HELMET de handleiding

Categorie
Lassysteem
Type
de handleiding
Deze handleiding is ook geschikt voor