Yamaha YSP-3050BL Handleiding

Merk: Yamaha

Model: YSP-3050BL

Categorie: Aanvullende muziekapparatuur

Type: Handleiding

Deze handleiding is ook geschikt voor

YSP-3050

YSP-3050

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY. LTD.

LEVEL 1, 99 QUEENSBRIDGE STREET, SOUTHBANK, VIC 3006, AUSTRALIA

Printed in Malaysia WK75600

YSP-3050

Digital Sound Projector

OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

i En

■ Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert you to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert you to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning

storms or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power supply cable or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT SAFETY INSTRUCTIONS

ii En

FCC INFORMATION (for US customers)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void

your authority, granted by the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories and/or another

product use only high quality shielded cables. Cable/s supplied

with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference

with other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the operation

of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is

found to be the source of interference, which can be determined

by turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures:

Relocate either this product or the device that is being affected

by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe

Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

We Want You Listening For A Lifetime

Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying

blaring or distortion – and, most importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries

Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

iii En

To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place with at least 5 cm (2 in) of space above (or below) this unit

– away from direct sunlight, heat sources, vibration, dust,

moisture, and/or cold.

3 Locate this unit away from other electrical appliances, motors, or

transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from cold

to hot, and do not locate this unit in an environment with high

humidity (i.e. a room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this

unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire, damage

to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this

unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to obstruct heat radiation. If the temperature inside

this unit rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all connections are

complete.

8 Do not operate this unit upside-down. It may overheat, possibly

causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power supply cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might damage

the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this unit

with a higher voltage than specified is dangerous and may cause

fire, damage to this unit, and/or personal injury. Yamaha will not

be held responsible for any damage resulting from use of this unit

with a voltage other than specified.

13 To prevent damage by lightning, keep the power supply cable

disconnected from a wall outlet or this unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the power supply cable from the wall

outlet.

16 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

17 Before moving this unit, press STANDBY/ON to set this unit in

standby mode, and disconnect the power supply cable from the

wall outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power supply cable from the

outlet, then leave the unit alone.

19 When using the unit for a long time, the unit may become warm.

Turn the power off, then leave the unit alone for cooling.

20 Install this unit near the AC outlet and where the AC power plug

can be reached easily.

21 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like.

Caution: Read this before operating this unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as long as

it is connected to the AC wall outlet, even if this unit itself is

turned off by STANDBY/ON. This state is called the standby

mode. In this state, this unit is designed to consume a very small

quantity of power.

IMPORTANT

Please record the serial number of this unit in the space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit. Retain this

Owner’s Manual in a safe place for future reference.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide slot

and fully insert.

This Class B digital apparatus complies with Canadian ICES-003.

POUR LES CONSOMMATEURS CANADIENS

Pour éviter les chocs électriques, introduire la lame la plus

large de la fiche dans la borne correspondante de la prise et

pousser jusqu’au fond.

Cet appareil numérique de la classe B est conforme à la norme

NMB-003 du Canada.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type.

CAUTION

Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation

exposure.

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

SETUP

English

1 En

Overview.................................................................. 2

Features ................................................................... 3

Using this manual ................................................... 5

Supplied accessories ............................................... 6

Controls and functions ........................................... 7

Front panel ................................................................. 7

Front panel display .................................................... 8

Rear panel .................................................................. 9

Remote control......................................................... 10

Installation............................................................. 13

Before installing this unit......................................... 13

Installing this unit .................................................... 13

Connections ........................................................... 16

Before connecting components................................ 17

Case 1: Connections using HDMI cables ................ 18

Case 2: Connecting a DVD player/recorder and tuner

(digital satellite, cable TV or digital airwave)..... 19

Case 3: Connecting other connection methods........ 20

Connecting a TV without an HDMI cable............... 21

Connecting a portable audio player ......................... 22

Connecting a subwoofer .......................................... 22

Connecting the FM antenna..................................... 23

About the IR IN jack................................................ 23

Connecting the AC power supply cable .................. 23

Getting started ...................................................... 24

Installing batteries in the remote control ................. 24

Operation range of the remote control..................... 24

Turning on this unit or

setting it to the standby mode.............................. 25

Using SET MENU................................................. 26

Displaying the OSD (on-screen display) ................. 26

The flow chart of SET MENU................................. 27

Changing OSD language ...................................... 28

AUTO SETUP (IntelliBeam) ............................... 29

The flow chart of AUTO SETUP ............................ 29

Installing the IntelliBeam microphone .................... 30

Using AUTO SETUP (IntelliBeam)........................ 31

Using the system memory .................................... 36

Convenient usage of the system memory ................ 36

Saving settings......................................................... 36

Loading settings....................................................... 37

Playback ................................................................ 39

Selecting the input source........................................ 39

Playing back sources................................................ 40

Adjusting the volume............................................... 41

FM tuning.............................................................. 42

FM controls and functions....................................... 42

Automatic tuning ..................................................... 43

Manual tuning.......................................................... 43

Automatic preset tuning........................................... 44

Manual preset tuning ............................................... 45

Selecting a preset station ......................................... 46

XM™ Satellite Radio tuning ............................... 47

Connecting XM™ Mini-Tuner Home Dock ........... 47

Activating XM™ Satellite Radio ............................ 48

Basic XM™ Satellite Radio operations................... 48

Presetting the XM™ Satellite Radio channels ........ 51

Displaying the XM™ Satellite Radio information.... 52

Using iPod™ ..........................................................53

Connection............................................................... 53

Controlling iPod™................................................... 53

Enjoying surround sound .....................................56

5 Beam..................................................................... 56

Stereo plus 3 Beam .................................................. 57

3 Beam..................................................................... 57

My Surround............................................................ 57

Enjoying 2-channel sources

in surround sound ................................................ 59

Enjoying TV in surround sound .............................. 60

Adjusting surround mode parameters...................... 61

Enjoying stereo sound...........................................62

2-channel stereo playback........................................ 62

5-channel stereo playback........................................ 62

Playing back sound clearly (My Beam)...............63

Using auto-adjust function....................................... 63

Using manual-adjust function.................................. 64

Using sound field programs..................................65

CINEMA DSP programs ......................................... 66

Using the music enhancer.....................................68

Using the volume mode

(Night listening enhancer/TV volume equal

mode) ..................................................................69

Using the sleep timer.............................................70

Displaying the input source information.............72

Using the HDMI control feature ..........................73

MANUAL SETUP .................................................74

Using MANUAL SETUP ....................................... 75

BEAM MENU ......................................................... 76

SOUND MENU....................................................... 80

INPUT MENU......................................................... 82

DISPLAY MENU.................................................... 86

Adjusting the audio balance .................................87

Using the test tone ................................................... 87

Using the audio output being played back............... 88

Selecting the input mode.......................................90

Adjusting the system parameters ........................91

Using the system parameters ................................... 91

Remote control features........................................94

Setting remote control codes ................................... 94

Controlling other components ................................. 95

Using the TV macro ................................................ 98

Troubleshooting...................................................100

Glossary................................................................104

Index .....................................................................106

Specifications .......................................................107

Contents

INTRODUCTION

PREPARATION

SETUP

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

List of remote control codes ............................................. i

Overview

2 En

It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of

wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of

surround sound experience as your local movie theater.

Yamaha YSP-3050 Digital Sound Projector challenges this preconception that complicated speaker setup and

troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.

This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is

not only easy to set up, but is also capable of reproducing the kind of powerful surround sound you have been waiting for

from its built-in 2 woofers and 21 full-range small speakers.

You can fine-tune the parameters of this unit to adjust the delay time for separate sound beams, resulting in highly

directional sound that comes in on the listening position from all directions.

The YSP-3050 projects sound beams containing surround sound information for the front right (R), front left (L),

surround right (SR), and surround left (SL) speaker positions, which are reflected off the walls of your listening room

before reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector

creates true-to-life 5.1-channel surround sound that makes you feel as if there are actual speakers around the room.

Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.

Overview

Listening position

Imaginary

surround left

speaker

Imaginary

surround right

speaker

Imaginary

front left

speaker

Imaginary

front right

speaker

Imaginary

center

speaker

Features

3 En

INTRODUCTION

English

Digital Sound Projector™

The Digital Sound Projector technology allows one slim

unit to control and steer multiple channels of sound to

generate multi-channel surround sound, thus eliminates

the need for satellite loudspeakers and cabling normally

associated with conventional surround sound systems.

This unit also employs the beam modes that let you enjoy

the surround sound (5 Beam, Stereo plus 3 Beam and 3

Beam), 2-channel and 5-channel stereo playback, and My

Beam.

My Surround

In addition to the above mentioned beam modes, this unit

is equipped with My Surround beam mode that allows you

to enjoy surround system even in a small listening area.

My Surround is a function integrated and optimized with

DiMAGIC's Euphony technology and Yamaha's Beam

reproduction system.

My Beam

This unit employs My Beam that ensures a clear sound in

a noisy environment. You can adjust the beam angle

manually or automatically.

Cinema DSP

This unit employs the Cinema DSP technology developed

by Yamaha Corporation that lets you experience movies at

home with all the original dramatic sound impact.

HDMI™ (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced, or high-definition

video (including 1080p video signal transmission) as well as

multi-channel digital audio based on HDCP

◆ Simple and easy connections with HDMI supported external

components

◆ Functional link with an HDMI control-compatible TV

◆ Analog video up-scaling from 480i (NTSC)/576i (PAL) or

480p (NTSC)/576p (PAL) to 720p or 1080i

Versatile Remote Control

The supplied remote control comes with preset remote

control codes used to control the DVD player, VCR, cable

TV tuner, and digital satellite tuner connected to this unit.

In addition, the remote control is equipped with the macro

capability that enables a series of operations with the press

of a single button.

AUTO SETUP (IntelliBeam)

This unit employs the automatic sound beam and acoustic

optimization technology with the aid of the supplied

IntelliBeam microphone. You can avoid troublesome

listening-based speaker setup and achieve highly accurate

sound beam adjustments that best match your listening

environment.

Compatibility with the Newest Technologies

This unit employs decoders compatible with Dolby

Digital, DTS, Dolby Pro Logic, Dolby Pro Logic II, DTS

Neo:6, Music Enhancer, and Neural Surround.

◆ Dolby Digital

This is the standard audio signal format used on various

digital media such as DVD, Blu-ray, and HD DVD. This

surround technology delivers high-quality digital audio for up

to 5.1 discrete channels to produce a directional and more

realistic effect.

◆ DTS

This is the standard audio signal format used on various

digital media such as DVD, Blu-ray, and HD DVD. This

surround technology delivers high-quality digital audio for up

to 5.1 discrete channels to produce a directional and more

realistic effect.

◆ Dolby Pro Logic

A surround system that takes a 4-channel signal and records it

as a 2-channel signal, then by way of some arithmetic

processing converts back to an independent 4-channel signal

for playback.

◆ Dolby Pro Logic II

Dolby Pro Logic II is an improved technique used to decode

vast numbers of existing Dolby Surround software.

This new technology enables a discrete 5-channel playback

with 2 front left and right channels, 1 center channel, and 2

surround left and right channels (instead of only 1 surround

channel for conventional Pro Logic technology).

◆ DTS Neo:6

This technology decodes the conventional 2-channel sources

for 6-channel playback, enabling playback with the full-range

channels with higher separation. Music mode and Cinema

mode are available to play back music and movie sources

respectively.

◆ Music Enhancer to restore the original depth and width of

compression artifacts such as the MP3 format.

◆ Neural Surround decoder.

Sophisticated FM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

XM™ Satellite Radio

◆ XM Satellite Radio tuning capability (using the XM Mini-

Tuner Dock, and Antenna sold separately by XM Satellite

Radio)

◆ Neural Surround decoder to play back the XM HD content of

XM Satellite Radio broadcasts in multi-channels, resulting in

a full surround sound experience

◆ XM Satellite Radio information displaying capability

iPod™ Controlling Capability

◆ DOCK terminal to connect a Yamaha iPod universal dock

(such as the YDS-10, sold separately), which supports iPod

(Click and Wheel), iPod nano, and iPod mini

◆ Playback information displaying capability

◆ Battery charging capability

Features

4 En

The “ ” logo and “IntelliBeam” are trademarks of

Yamaha Corporation.

The “ ” logo and “Cinema DSP” are registered

trademarks of Yamaha Corporation.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS” and “Neo:6” are registered trademarks of DTS, Inc.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks or registered trademarks of HDMI

Licensing LLC.

Manufactured under license from 1 Ltd. Worldwide patents

applied for.

The “ ” logo and “Digital Sound Projector

™

” are trademarks

of 1 Ltd.

TruBass, SRS and the “ ” symbol are registered trademarks

of SRS Labs, Inc. TruBass technology is incorporated under

license from SRS Labs, Inc.

™

is a trademark of DiMAGIC Co., Ltd.

“iPod” is a trademark of Apple Inc., registered in the U.S. and

other countries.

The XM name and related logos are registered trademarks of XM

Satellite Radio Inc.

Neural Surround

™

name and related logos are trademarks owned

by Neural Audio Corporation.

iPod

Using this manual

5 En

INTRODUCTION

English

• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the

supplied owner’s manual for each component.

• Operations in this manual use keys on the supplied remote control of this unit unless otherwise specified.

• y indicates a tip for your operation.

• This manual is printed prior to production. Designs and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and the product, the product has priority.

1 Install this unit in your listening room.

See “Installation” on page 13.

2 Connect this unit to your TV and other external components.

See “Connections” on page 16.

3 Prepare the remote control and turn on the power of this unit.

See “Getting started” on page 24.

4 Run AUTO SETUP.

See “AUTO SETUP (IntelliBeam)” on page 29.

5 Play back a source.

See “Playback” on page 39.

6 Change the beam modes and/or CINEMA DSP settings.

See “Enjoying surround sound” on page 56.

7 Run MANUAL SETUP to fine-tune settings and/or set remote control codes.

See “MANUAL SETUP” on page 74 and “Remote control features” on page 94.

Using this manual

Notes

If you want to make additional settings

and adjustments

Supplied accessories

6 En

Check that you have received all of the following parts.

Supplied accessories

STEREO MY SUR.

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

SUR. DECODE

OFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

YSP

TV/AV

ENTRY

CAT/

A-E

321

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

+10

Remote control (×1)

Batteries (×2)

(AA, R6, UM-3)

OSD* video pin cable (×1)

IntelliBeam microphone

(×1)

Fasteners (×4)

Audio pin cable (×1)

Digital audio pin cable (×1)

Optical cable (×1)

Cable clamp (×1)

Cardboard microphone

stand (×1)

(Orange)

(White/Red)

(Yellow)

Indoor FM antenna (×1)

Demonstration DVD

(×1)

QUICK REFERENCE

GUIDE

*OSD: On-Screen Display

Controls and functions

7 En

INTRODUCTION

English

1 AUX 3 input jack

Connect your portable audio player (see page 22).

2 INTELLIBEAM MIC jack

Connect the supplied IntelliBeam microphone for AUTO

SETUP (see page 30).

3 Remote control sensor

Receives infrared signals from the remote control.

4 Front panel display

Shows information about the operational status of this

unit.

5 INPUT

Press repeatedly to switch between input sources (see

page 39).

6 VOLUME +/–

Controls the volume level of all audio channels (see

page 41).

7 STANDBY/ON

Turns on the power of this unit or sets it to the standby

mode (see page 25).

• When you turn on this unit, you will hear a click sound

followed by the 4 to 5-second interval before sound

reproducing.

• In the standby mode, this unit consumes a small amount of

power in order to receive infrared signals from the remote

control or to search for HDMI signals.

Controls and functions

Front panel

3 4

STANDBY/ON

VOLUME

INPUT

INTELLIBEAM MIC

AUX 3

Notes

Controls and functions

8 En

1 HDMI indicator

Lights up when the signal of the selected input source is

input at the HDMI IN jack(s).

2 TUNER indicators

FM: Light up when this unit is receiving an FM broadcast

(see pages 43 to 45).

XM: MEMORY flashes during the XM preset operation

(see page 51).

3 CINEMA DSP indicator

Lights up when a CINEMA DSP program is selected (see

page 66).

4 PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code

Modulation) digital audio signals.

5 Decoder indicators

Light up when the corresponding decoder operates

(see page 58).

6 ENHANCER indicator

Lights up when the Music Enhancer is selected (see

page 68).

7 Volume level indicator

Displays the current volume level.

8 DOCK indicator

Lights up when your iPod (Click and Wheel), iPod nano,

or iPod mini is connected to this unit via the DOCK

terminal on this unit.

9 SRS TruBass indicator

Lights up when TruBass is turned on (see page 81).

0 EQUAL indicator

Lights up when the TV volume equal mode is selected

(see page 69).

A NIGHT indicator

Lights up when one of the night listening enhancers is

selected (see page 69).

B SLEEP indicator

Lights up when the sleep timer is set (see page 70).

C XM indicator

Lights up when XM is selected as the input source.

D Multi-information display

Shows information with alphanumeric characters when

you adjust the parameters of this unit.

E Input channel indicators

Show information when you adjust the parameters of this

unit. The channel component of the current digital input

signal is displayed (see page 58).

You can adjust the brightness and display setting of the front

panel display using the F.DISPLAY SET parameter in MANUAL

SETUP (see page 86).

Front panel display

AB C D

Controls and functions

9 En

INTRODUCTION

English

1 ANTENNA jack

Connect the FM antenna (see page 23).

2 DOCK terminal

Connect the Yamaha iPod universal dock (such as YDS-

10, sold separately) (see page 53).

3 AUX 1 AUDIO INPUT jacks

Connect an external component via an analog connection

(see page 20).

4 TV/STB AUDIO INPUT jacks

Connect your TV, digital satellite tuner, or cable TV tuner

via an analog connection (see pages 21).

5 VIDEO OUT jack

Connect to the video input jack of your TV via a

composite analog video connection to display the OSD of

this unit (see page 21).

6 SUBWOOFER OUT jack

Connect your subwoofer (see page 22).

7 STB VIDEO INPUT jacks

Connect a digital satellite tuner or a cable TV tuner via a

composite analog video connection (see pages 19).

8 DVD COMPONENT VIDEO INPUT jacks

Connect a DVD player/recorder or an external component

via a component analog video connection (see pages 19

and 20).

9 AUX 2 COAXIAL DIGITAL INPUT jack

Connect an external component via a coaxial digital

connection (see page 20).

0 AUX 1 OPTICAL DIGITAL INPUT jack

Connect an external component via an optical digital

connection (see page 20).

A TV/STB OPTICAL DIGITAL INPUT jack

Connect your TV, digital satellite tuner, or cable TV tuner

via an optical digital connection (see pages 19 and 21).

B DVD COAXIAL DIGITAL INPUT jack

Connect your DVD player via a coaxial digital connection

(see page 19).

C XM antenna jack

Connect your XM Mini-Tuner Home Dock (sold

separately) (see page 47).

D IR IN terminal

This is a control expansion terminal for commercial use

only (see page 23).

E STB HDMI IN jack

Connect your digital satellite tuner, cable TV tuner, digital

airwave tuner, or game console via an HDMI connection

(see page 18).

F DVD HDMI IN jack

Connect your DVD player via an HDMI connection (see

page 18).

G HDMI OUT jack

Connect to the HDMI input jack on your HDMI

component such as a TV or a projector connected to this

unit (see page 18 to 20).

H AC power supply cable

Connect to the AC wall outlet (see page 23).

Rear panel

STB

DVD

OUT

HDMI

XMDIGITAL INPUTVIDEO INPUT

VIDEO

COMPONENT

AUX 2 DVD

SUBWOOFER

AUX 1 TV/STB STB DVD TV/STB

COAXIAL

OPTICAL

AUX 1

OUT

FM75Ω

UNBAL.

AUDIO INPUTANTENNA

DOCK

IR IN

AB C D

Controls and functions

10 En

This section describes the functions of the remote control

used to control this unit. Some buttons marked with an

asterisk (*) share the common functions between the YSP

and TV/AV operation modes (S).

You can also control other components using the remote control

once you set the appropriate remote control codes. See

“Controlling other components” on page 95 for details.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 STANDBY/ON

Sets this system to the standby mode (see page 25).

3 Transmission indicator

Lights up when infrared control signals are being output.

4 Input selector buttons

Use to select an input source (DVD, AUX1, AUX2,

AUX3/DOCK, STB, TV, or FM/XM).

5 VOL MODE

Turns on or off the volume modes (see page 69).

6 AUTO SETUP

Enters the AUTO SETUP menu (see page 29).

7 Sound field program buttons

Select the sound field programs (see page 65).

8 ENHANCER

Turns on or off the Music Enhancer (see page 68).

9 Cursor buttons / / / , ENTER

Select and adjust SET MENU items.

0 DISPLAY

Displays information on the selected input signal.

A VOLUME +/–

Increases or decreases the volume level of this unit (see

page 41).

B MUTE

Mutes the sound. Press again to restore the audio output to

the previous volume level (see page 41).

C TV INPUT

Toggles between the input source on your TV (see

page 95).

D CH LEVEL

Adjusts the volume level of each channel (see page 88).

E TEST

Outputs a test tone when adjusting the output level of each

channel (see page 87).

Remote control

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

OFF

CODE SET

SPORTS

5BEAM ST+3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

YSP

TV/AV

ENTRY

CAT/

A-E

321

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

+10

MY SUR.

3BEAM

SUR. DECODE

Controls and functions

11 En

INTRODUCTION

English

F DVD player/VCR control buttons

Control your DVD player or VCR (see pages 95 and 97).

G My Beam microphone

Collects the test tones from this unit when using the My

Beam auto-adjust function (see page 63).

H TV POWER

Turns on or off the power of your TV (see page 95).

I AV POWER

Turns on or off the power of the selected component (see

pages 95 and 97).

J INPUT1

Switches the input source on your TV (see page 95).

K MACRO

Use to set the TV macro (see page 98).

L a /5

Switches the preset station number (1 to 8) when this unit

is receiving an FM broadcast or XM channel (see

page 46).

M CAT

Switches the preset station group (A to E) when this unit is

receiving an FM broadcast or XM channel (see page 46).

N SLEEP

Sets the sleep timer (see page 70).

O INPUTMODE

Toggles between input modes (AUTO, DTS, and

ANALOG) (see page 90).

P Beam mode buttons

Change the beam mode settings (see pages 56, 62, and

63).

Q SUR. DECODE

Selects the surround mode for playback (see page 59).

R MENU

Displays the setup menu on your TV monitor (see

pages 31 and 75).

S Operation mode selector

Selects the operation mode of this unit. Select YSP when

operating this unit and select TV/AV when operating your

TV or other AV components.

T RETURN

Returns to the previous SET MENU screen.

U TV VOL +/–

Adjusts the volume level of your TV (see page 95).

V CH +/–

Changes the channels of your TV, digital satellite tuner,

cable TV tuner, or VCR (see pages 95 to 97).

W TV MUTE, CODE SET

Mutes the audio output of your TV (see page 95).

Sets up remote control codes (see page 94).

The functions L and M are available only when the FM/XM

stations are preset.

Note

Controls and functions

12 En

This section describes the functions of the remote control

used to control FM, XM Satellite Radio, or iPod when the

TV/AV mode is selected with the operation mode selector

(7).

1 PRESET/TUNE

FM: Switches between the preset search mode and the

frequency search mode (see pages 43 to 46).

2 Numeric buttons

FM, XM: Enter numbers.

3 Cursor buttons / / / , ENTER

FM: Use ENTRY ( / ) to change the preset station

number (1 to 8) or frequency level (see pages 43 to 46).

Use CAT/A-E ( / ) to change the preset station group

(A to E) (see pages 45 and 46).

XM: Use ENTRY ( / ) to select XM channels in

All Channel Search mode/Category Search mode, and to

select the preset channel number (1 to 8) in Preset Search

mode. Use CAT/A-E ( / ) to select XM categories in

All Channel Search mode/Category Search mode, and to

select the preset channel group (A to E) in Preset Search

mode. Use ENTER to confirm the input above (see

pages 49 to 51).

For further information on controlling iPod, see page 53.

4 DISPLAY

XM and iPod: Displays information when this unit is

receiving an XM channel (see page 52) or playing back

your iPod (see page 54).

5 MEMORY

FM: Stores the preset stations (see pages 44 and 45).

XM: Use to store the preset stations (see page 51).

6 SEARCH

FM: Switches between automatic and manual tuning (see

page 43).

XM: Switches between search modes (All Channel

Search, Category Search, and Preset Search) (see page 49

and 50).

7 Operation mode selector

Selects the operation mode of this unit. Select YSP when

operating this unit and select TV/AV when operating your

TV or other AV components.

321

+10

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

OFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

ENTRY

CAT/

A-E

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

YSP

TV/AV

SUR. DECODE

MY SUR.

Installation

13 En

PREPARATION

English

This section describes a suitable installation location to install this unit using a metal wall bracket, a rack or a stand.

Depending on your installation environment, connections with external components can be done before installing this

unit. We recommend that you temporarily place and arrange all components, including this unit, in order to decide which

procedure should come first. Especially when you make a connection over HDMI, we recommend that you make a

connection first before installation (see page 18).

This unit creates surround sound by reflecting projected

sound beams off the walls of your listening room. The

surround sound effects produced by this unit may not be

sufficient when this unit is installed in the following

locations.

• Rooms with walls inadequate for reflecting sound

beams

• Rooms with acoustically absorbent walls

• Rooms with measurements outside the following

range: W (3 to 7 m (10 to 23 ft)) x H (2 to 3.5 m (7 to

11.5 ft)) x D (3 to 7 m (10 to 23 ft))

• Rooms with less than 1.8 m (6 ft) from the listening

position to this unit

• Rooms where objects such as furniture are likely to

obstruct the path of sound beams

• Rooms where the listening position is close to the walls

• Rooms where the listening position is not in front of

this unit

• You can enjoy surround sound by selecting My Surround (see

page 57) as the beam mode even if your listening room may not

fulfill the above conditions (except when the listening position

is not directly facing toward the front of this unit).

• You can also enjoy surround sound by selecting 2-channel or 5-

channel stereo playback (see page 62) or My Beam (see

page 63) as the beam mode even if your listening room may not

fulfill the above conditions.

Make sure you leave an adequate amount of ventilation

space so that heat can escape. Make at least 5 cm (2 in) of

space above or below this unit.

• We do not recommend putting this unit directly on the floor of

your listening room. Please install this unit using a metal wall

bracket, a rack, or a stand.

• This unit weighs 11.5 kg (25 lbs 6 oz). Be sure to install this

unit where it will not fall subject to vibrations, such as from an

earthquake, and where it is out of the reach of children.

• When using a cathode-ray tube (CRT) TV, do not install this

unit directly above your TV.

• This unit is shielded against magnetic rays. However, if the

picture on your TV screen becomes blurred or distorted, we

recommend moving this unit away from your TV.

Install this unit where there are no obstacles such as

furniture obstructing the path of sound beams. Otherwise,

the desired surround sound effects may not be achieved.

You may install this unit in parallel with the wall or in the

corner.

Parallel installation

Install this unit in the exact center of the wall when it is

measured from the left and right corners.

Corner installation

Install this unit in the corner at a 40º to 50º angle from the

adjacent walls.

Installation

Before installing this unit

5 cm (2 in) or more

Rear

Front

Side view

Notes

Installing this unit

An object, such as furniture

40° to 50°

An object, such as furniture

14 En

Installation

■ Installation examples

Example 1

Install this unit as close to the exact center of the wall as possible.

Example 2

Install this unit so that the sound beams can be reflected off the walls.

Example 3

Install this unit as close to the exact front of your normal listening position as possible.

15 En

Installation

PREPARATION

English

■ Using a metal wall bracket

You can use the optional metal wall bracket to mount this

unit on the wall in your listening room.

Refer to the instructions supplied with the metal bracket for

details on how to attach the metal bracket to the wall or how to

attach this unit to the metal bracket.

■ Using a stand

You can mount your TV on a stand placed on a

commercially available rack and install this unit under

your TV.

Refer to the instructions supplied with the stand for details on

how to install the stand or how to mount the TV on the stand.

■ Using a rack

You can install this unit either above or under your TV in a

commercially available rack.

Make sure that the rack is large enough to allow adequate

ventilation space around this unit (see page 13) and that it is

strong enough to support the weight of both this unit and your TV.

■ Affixing this unit

Peel off the film from each of the four supplied fasteners

and then secure them to the bottom four corners of this

unit and the top of the rack, etc.

• Do not install this unit on top of a slanted surface. This unit may

fall over and cause injury.

• Make sure you wipe the surface of the rack, etc. before securing

the fasteners. Applying the tape to a dirty or wet surface will

weaken the sticking power of the tape, and this unit may fall as

a result.

112

670

4- 7

24- 7x22

325 65325

This unit

Metal wall bracket

YSP-3050

SPM-K30 (Option)

(mm)

This unit

Stand

Note

Notes

When this unit is installed above your TV

When this unit is installed under your TV

This unit

Peel off

the film

Fasteners

Connections

16 En

This unit is equipped with the following types of audio/video input/output jacks/terminal:

For audio input

• 2 optical digital input jacks

• 2 coaxial digital input jacks

• 2 sets of analog input jacks

• 1 universal dock terminal

For video input

• 1 composite video input jack

• 1 set of component video input jacks

For audio/video input

• 2 HDMI input jacks

For audio output

• 1 subwoofer output jack

For video output

• 1 analog output jack

For audio/video output

• 1 HDMI output jack

Use these jacks/terminal to connect external components such as your TV, DVD player, VCR, digital satellite tuner, cable

TV tuner, digital airwave tuner, portable audio player, game console, and iPod. Further, by connecting a subwoofer to this

unit, you can enjoy reinforced low-bass sounds. For details on how to connect various types of external components to

this unit, see pages 18 to 22.

• Do not connect this unit or other components to the mains power until all connections between components are

complete.

• Unplug the AC power supply cable before changing connections, moving or cleaning this unit.

Connections

CAUTION

This unit

Audio connection Video connection

VCR or game consoleDVD player Subwoofer Digital satellite tuner

or cable TV tuner

portable audio

player

17 En

Connections

PREPARATION

English

■ Cables used for connections

HDMI cable

Audio pin cable (supplied)

Optical cable (supplied)

Digital audio pin cable (supplied)

3.5 mm stereo mini plug cable

Subwoofer pin cable

OSD video pin cable (supplied)/ Video pin cable

Component video pin cable

■ Notes on connecting the optical cable

• Pull out the cap before connecting the optical cable.

When you are not using the optical cable, be sure to put the cap

back in place.

• When inserting the cable into the optical digital jack, make sure

the direction is correct.

■ Affixing cables

To prevent cables from becoming unplugged, place the supplied

cable clamp with the open side facing upward, attach it to the rear

panel of this unit in a suitable position, and then affix cables in

the cable clamp.

■ Information on HDMI™

Audio signals

•

When CPPM copy-protected DVD audio is played back, video and

audio signals may not be output depending on the type of DVD player.

• This unit is not compatible with HDCP-incompatible HDMI or

DVI components.

• We recommend that you use an HDMI cable shorter than 5 m

(16 ft) with the HDMI logo printed on it.

• Use a conversion cable (HDMI jack

↔ DVI-D jack) to connect

this unit to other DVI components.

■ Priority order for audio input signals

When multiple types of audio signals are simultaneously

being input from a single source component, this unit

plays back the audio signals in the following priority

order: HDMI → Digital → Analog

As default settings, the following input jacks are assigned

to the corresponding input sources:

This unit is compatible with 2-channel PCM signals, but not with

multi-channel PCM signals.

Before connecting components

Audio/Video

Audio

Video

(White)

(Red)

(White)

(Red)

(Orange)(Orange)

(Yellow)(Yellow)

(Green)

(Blue)

(Red)

(Blue)

(Red)

Cap

Input source Audio signal type

DVD video Dolby Digital, DTS, PCM

DVD audio

2-channel stereo

(up to 96 kHz/24 bit)

Blu-ray Disc

HD DVD

Dolby Digital, DTS, PCM

Notes

Input

jack

Input

source

HDMI Digital Analog

TV/STB ✔✔✔

DVD ✔✔

AUX 1 ✔✔

AUX 2 ✔

AUX 3 ✔

Note

Optical cable

Attach to this unit

18 En

Connections

This unit is equipped with 2 HDMI input jacks and 1 HDMI output jack. If your TV and other components have HDMI

jacks, use HDMI cables for simpler and easier connections, and you can skip the connection procedures from page 19 to

21. If your TV has a built-in digital satellite tuner and an optical digital output jack, connect the optical digital output jack

on your TV to the TV/STB OPTICAL DIGITAL IN jack on this unit.

• We recommend that you secure the HDMI cable(s) with adhesive tape, etc. once you have connected the HDMI cable(s) to the HDMI

jack(s) of this unit.

• This unit outputs analog video signals input at the video/component video jacks at the HDMI OUT jack. Similarly, this unit outputs

analog audio signals input at the analog input jacks at the HDMI OUT jack.

HDMI cable

Case 1: Connections using HDMI cables

STB

DVD

OUT

HDMI

AAA

HDMI

output

HDMI

input

HDMI

output

DVD player/recorder

Digital satellite tuner,

cable TV tuner,

digital airwave tuner,

or game console

This connection (except

for a game console) is not

necessary if your TV has a

built-in digital satellite

tuner, cable TV tuner, or

digital airwave tuner.

Rear panel of this unit

If TV built-in tuner is

used, connect the optical

digital output jack on your

TV to the TV/STB

OPTICAL DIGITAL

INPUT jack on this unit

(see page 21).

Audio/Video

19 En

Connections

PREPARATION

English

For audio connection, connect the coaxial digital output jack on your DVD player/recorder to the DVD COAXIAL

DIGITAL INPUT jack on this unit. When you connect this unit to your DVD/VCR combo player/recorder, connect the

analog audio output jacks on your DVD/VCR combo player/recorder to the AUX 1 AUDIO INPUT jacks on this unit in

addition to the coaxial digital audio connection. Connect the optical digital output jack on your tuner (digital satellite,

cable TV or digital airwave) to the TV/STB OPTICAL DIGITAL INPUT on this unit.

For video connection, connect the component video output jack of your DVD player/recorder to the COMPONENT

VIDEO INPUT jacks on this unit. Connect the video output jack on your tuner (digital satellite, cable TV) to the STB

VIDEO INPUT jack on this unit.

Connect the HDMI input jack on your TV to the HDMI OUT jack.

To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 17).

• Check that your DVD player/recorder is properly set to output Dolby Digital and DTS digital audio signals. If not, adjust the system

settings of your DVD player/recorder. For details, refer to the operation manual supplied with your DVD player/recorder.

• If your DVD player/recorder does not have a coaxial digital output jack, connect the analog audio output jacks on your DVD player/

recorder to the AUX 1 AUDIO INPUT jacks on this unit.

HDMI cable

OSD video pin cable

Component video pin cable

Optical cable

Digital audio pin cable

Case 2: Connecting a DVD player/recorder and tuner (digital satellite,

cable TV or digital airwave)

Notes

STB

DVD

OUT

HDMI

DIGITAL INPUTVIDEO INPUT

VIDEO

COMPONENT

AUX 2 DVD

SUBWOOFER

AUX 1 TV/STB STB DVD TV/STB

COAXIAL

OPTICAL

AUX 1

OUTAUDIO INPUT

Component

video output

DVD player/recorder

Digital satellite tuner, cable TV tuner,

digital airwave tuner, or game console

Rear panel of this unit

Coaxial

digital

output

Optical

digital

output

Video

output

HDMI

input

Audio/Video

Video

Audio

20 En

Connections

If your component supports optical digital connections, connect the optical digital output jack on your component

(e.g., DVD player/recorder) to the AUX 1 OPTICAL DIGITAL INPUT jack on this unit. If your component does not

support optical digital connections, connect the coaxial digital output jack on your component to the AUX 2 COAXIAL

DIGITAL INPUT jack on this unit.

If your component does not support any digital connections, connect the analog audio output jacks on your component

(e.g., VCR) to the AUX 1 AUDIO INPUT jacks on this unit.

To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 17).

If you make analog and digital audio connections at the same time as shown in the illustration below, the digital audio signals input at

the AUX 1 OPTICAL DIGITAL INPUT jack take priority over the analog audio signals input at the AUX 1 AUDIO INPUT jacks.

OSD video pin cable Audio pin cable

Optical cable

Digital audio pin cable

Case 3: Connecting other connection methods

Note

DIGITAL INPUTVIDEO INPUT

VIDEO

COMPONENT

AUX 2 DVD

SUBWOOFER

AUX 1 TV/STB STB DVD TV/STB

COAXIAL

OPTICAL

AUX 1

OUTAUDIO INPUT

21 3

Optical

digital

output

DVD player/recorder, VCR,

game console, CD player, etc.

Coaxial

digital

output

Video signal to the TV

Video

input

Analog audio

output

Rear panel of this unit

Video Audio

21 En

Connections

PREPARATION

English

For audio connection, connect the analog audio output jacks on your TV to the TV/STB AUDIO INPUT jacks on this

unit. If your TV has an optical digital output jack, connect the optical digital output jack on your TV to the TV/STB

OPTICAL DIGITAL INPUT jack on this unit.

For video connection, connect the video input jack on your TV to the VIDEO OUT jack on this unit to display the OSD

for easy viewing when you adjust the system parameters in SET MENU.

To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 17).

If you make analog and optical digital audio connections at the same time as shown in the illustration below, the digital audio signals

input at the TV/STB OPTICAL DIGITAL INPUT jack take priority over the analog audio signals input at the TV/STB AUDIO INPUT

jacks.

OSD video pin cable Audio pin cable

Optical cable

Connecting a TV without an HDMI cable

Notes

DIGITAL INPUTVIDEO INPUT

VIDEO

COMPONENT

AUX 2 DVD

SUBWOOFER

AUX 1 TV/STB STB DVD TV/STB

COAXIAL

OPTICAL

AUX 1

OUTAUDIO INPUT

Rear panel of this unit

Optical

digital

output

Video

input

Analog audio

output

Video Audio

22 En

Connections

Connect the analog audio output jack on your portable

audio player to the AUX 3 input jack on the front panel of

this unit.

3.5 mm stereo mini plug cable

Connect the monaural input jack on your subwoofer to the

SUBWOOFER OUT jack on this unit.

This connection alone does not output sound from the

connected subwoofer. To output sound from the connected

subwoofer, turn on the power of your subwoofer and then

run AUTO SETUP (see page 29) or select SUBWOOFER

for BASS OUT in SUBWOOFER SET (see page 80).

Subwoofer pin cable

Connecting a portable audio player

Audio

AUX 3

Portable audio player

Front panel of this unit

Analog

audio

output

Connecting a subwoofer

Audio

VIDEO INPUT

VIDEO

COMPONENT

SUBWOOFER

AUX 1 TV/STB STB DVD

OUTAUDIO INPUT

Monaural

input

Subwoofer

Rear panel of this unit

23 En

Connections

PREPARATION

English

Connect the supplied FM antenna to the FM ANTENNA jack on this unit.

The IR IN jack does not support normal external component connection. This is a control expansion terminal for

commercial use only.

Once all other connections are complete, plug the AC power supply cable into the AC wall outlet.

Connecting the FM antenna

VIDEO INPUT

VIDEO

COMPONENT

SUBWOOFER

AUX 1 TV/STB STB DVD

OUT

FM75Ω

UNBAL.

AUDIO INPUTANTENNA

DOCK

Rear panel of this unit

FM indoor antenna (supplied)

About the IR IN jack

Connecting the AC power supply cable

XMDIGITAL INPUT

AUX 2 DVD

TV/STB

COAXIAL

OPTICAL

AUX 1

IR IN

Rear panel of this unit

To the AC wall outlet

GETTING STARTED

24 En

1 Press and hold the mark on the battery

cover and then open the cover.

2 Insert the two supplied batteries (AA, R6,

UM-3) into the battery compartment.

Make sure you insert the batteries according to the

polarity markings (+/–).

3 Close the battery cover.

• Change all of the batteries if you notice the following

conditions: the operation range of the remote control decreases

or the transmission indicator does not light up or becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• Exhausted batteries may leak. If the batteries have leaked,

dispose of them immediately. Avoid touching the leaked

material or letting it come into contact with clothing, etc. Clean

the battery compartment thoroughly before installing new

batteries.

• Do not throw away batteries with general house waste. Dispose

of them correctly in accordance with your local regulations.

• The memory stored in the remote control may be erased in the

following cases:

– The remote control is left without batteries for more than two

minutes.

– Exhausted batteries remain in the remote control.

– The buttons on the remote control are accidentally pressed

when you change batteries.

• If the memory stored in the remote control is unwantedly

erased, insert new batteries and set the remote control codes

again.

Remove the transparent sheet before using the remote control.

The remote control transmits a directional infrared beam.

Use the remote control within 6 m (20 ft) of this unit and

point it toward the remote control sensor of this unit

during operation.

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following places:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or a stove

– places of extremely low temperatures

– dusty places

• Do not expose the remote control sensor of this unit to direct

sunlight or lighting such as inverted fluorescent lamps.

• If the batteries grow old, the effective operation range of the

remote control decreases considerably. If this happens, replace

the batteries with two new ones as soon as possible.

Getting started

Installing batteries in the remote

control

Notes

Press

Operation range of the remote

control

Notes

45 45

Approximately

6 m (20 ft)

Getting started

25 En

SETUP

English

1 Press STANDBY/ON to turn on the power of

this unit.

The volume level appears in the front panel display,

and the current input source and beam mode are

displayed.

2 Press STANDBY/ON again to set this unit to

the standby mode.

When this unit is in the standby mode, only STANDBY/ON on

the front panel or on the remote control is operational, and the

other control buttons on the front panel or on the remote control

are not operational until the power of this unit is turned on.

Turning on this unit or

setting it to the standby mode

STANDBY/ON

VOLUME

INPUT

PRESET/TUNE

MEMORYSEARCH

CATFM/XM

MACRO

INPUT1

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

STANDBY/ON

Front panel

Remote control

VOLUME 30

Current volume level

TV/STB MY SUR

Current input

source

Current beam

mode

Note

USING SET MENU

26 En

This section describes how to display the OSD (on-screen display) of this unit on your TV screen and to set the

parameters for your listening room. Once this is complete, you can enjoy real surround sound while watching TV in the

comfort of your own home.

1 Check that the video input jack on your TV is

connected to the VIDEO OUT jack on this unit

to display the OSD of this unit.

2 Press STANDBY/ON to turn on the power of

this unit.

3 Turn on the power of your TV.

4 Set the operation mode selector to YSP.

5 Press MENU.

The SET MENU screen appears on your TV.

Using SET MENU

Displaying the OSD (on-screen display)

STANDBY/ON

Front panel

Remote control

YSP

TV/AV

;MEMORY

;AUTO SETUP

;MANUAL SETUP

;LANGUAGE SETUP

[ ]/[ ]:Up/Down

[ENTER]:Enter

SET MENU

Using SET MENU

27 En

SETUP

English

The following diagram illustrates the overall flow of the setup procedure.

The flow chart of SET MENU

Run AUTO SETUP (IntelliBeam).

See “AUTO SETUP (IntelliBeam)” on page 29.

Look for a remedy.

See “Error messages for AUTO SETUP” on page 35 for a complete list of error

messages and possible remedies.

Play back audio signals or adjust the settings for the beam mode and the CINEMA DSP.

See “Playback” on page 39, “Enjoying surround sound” on page 56, and “Using sound field programs” on

page 65.

Run MANUAL SETUP.

See “MANUAL SETUP” on page 74.

• If you cannot clearly hear a sound beam from a specific channel, adjust settings for

SETTING PARAMETERS (see page 76) or for BEAM ADJUSTMENT (see page 77) in

BEAM MENU.

• If there are acoustically absorbent objects such as curtains in the path of the sound beams,

adjust settings for TREBLE GAIN in BEAM MENU (see page 79).

If an error occurs

If you want to make additional settings

and adjustments

Run LANGUAGE SETUP.

See “Changing OSD language” on page 28.

CHANGING OSD LANGUAGE

28 En

This feature allows you to select the language of your choice that appears in SET MENU of this unit.

1 Set the operation mode selector to YSP.

2 Press MENU.

The SET MENU screen appears on your TV.

• The control buttons used for SET MENU are displayed at

the bottom of the screen.

• To return to the previous screen while using SET MENU,

press RETURN.

• To exit from SET MENU, press MENU once more.

• You can also perform the following operations while

viewing information in the front panel display.

3 Press / to select LANGUAGE SETUP,

and press ENTER.

The following screen appears on your TV.

4 Press / to select the desired language,

and press ENTER.

Choices: ENGLISH (English), DEUTSCH (German),

Français (French), ESPAÑOL (Spanish),

ITALIANO (Italian), NEDERLANDS (Dutch),

Русский (Russian)

Changing OSD language

YSP

TV/AV

;MEMORY

;AUTO SETUP

;MANUAL SETUP

;LANGUAGE SETUP

[ ]/[ ]:Up/Down

[ENTER]:Enter

SET MENU

ENTER

ENGLISH

DEUTSCH

Francais

ESPANOL

ITALIANO

NEDERLANDS

[ ]/[ ]:Select

[ENTER]:Return

;LANGUAGE SETUP

ENTER

AUTO SETUP (INTELLIBEAM)

29 En

SETUP

English

This unit creates a sound field by reflecting sound beams on the walls of your listening room and by broadening the

cohesion of all the channels. Just as you would arrange the speaker position of other audio systems, you need to set the

beam angle to enjoy the best possible sound from this unit.

This unit employs the beam optimization and sound optimization features with the aid of the supplied IntelliBeam

microphone, allowing you to avoid troublesome listening-based setup and achieving highly accurate sound adjustments

that best match your listening environment. We call these two features “IntelliBeam” generically.

Beam optimization:

This feature optimizes the beam angle so that the parameter best matches your listening environment.

Sound optimization:

This feature optimizes the beam delay, volume, and quality so that the parameters best match your listening environment.

This unit performs a series of checks to optimize the beam angle, delay, volume, and quality. You can choose to optimize

all or part of the parameters.

The beam angle checking procedure is skipped if SOUND

OPTIMZ only is selected.

The sound optimization procedure is skipped if BEAM

OPTIMZ only is selected.

The subwoofer checking procedure is skipped if BEAM

OPTIMZ only is selected.

AUTO SETUP (IntelliBeam)

The flow chart of AUTO SETUP

*2 *3

Checking the environment of

your listening room

Optimizing the beam angle

Checking the subwoofer and

optimizing the beam delay,

frequency, and volume

Beam

optimization

Sound

optimization

Notes

AUTO SETUP (IntelliBeam)

30 En

The supplied IntelliBeam microphone collects and analyzes the sound that this unit produces in your actual listening

environment. Follow the procedure below to connect the IntelliBeam microphone to this unit and make sure that the

IntelliBeam microphone is placed in a proper location and that there are no large obstacles between the IntelliBeam

microphone and the walls in your listening room.

• After you have completed the AUTO SETUP procedure, be sure to disconnect the IntelliBeam microphone.

• The IntelliBeam microphone is sensitive to heat.

– Keep it away from direct sunlight.

– Do not place it on top of this unit.

• Do not connect the IntelliBeam microphone to an extension cable as doing so may result in an inaccurate sound optimization.

• An error may occur during the AUTO SETUP procedure if the IntelliBeam microphone is not properly placed in your listening room.

To avoid the possibility of an error:

– Do not place the IntelliBeam microphone to the extreme right or left from the center of this unit.

– Do not place the IntelliBeam microphone within 1.8 m (6.0 ft) from the front of this unit.

– Do not place the IntelliBeam microphone more than 1 m (3.3 ft) upper or lower from the center height of this unit.

• Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects

obstruct the path of sound beams. However, any objects that are in contact with the walls will be regarded as a protruding part of the

walls.

• The best possible results are achieved if the IntelliBeam microphone is placed at the same height as your ears would be when you are

seated in your listening position. However, if this is not possible, you can manually fine-tune the sound beam angle and balance the

sound beam output levels using MANUAL SETUP (see page 74) once the AUTO SETUP procedure is completed.

• If a subwoofer with adjustable volume and crossover/high-cut frequency controls is connected to

this unit, set the volume between 10 and 12 o’clock as viewed on a conventional clockface and set

the crossover/high-cut frequency to the maximum.

1 Press STANDBY/ON to turn off the power of

this unit.

2 Connect the supplied IntelliBeam

microphone to the INTELLIBEAM MIC jack on

the front panel.

3 Place the IntelliBeam microphone on a flat

level surface more than 1.8 m (6.0 ft) from the

front of the unit and within 1 m (3.3 ft) upper

or lower from the center height of the unit

with the IntelliBeam microphone facing

upward at your normal listening position.

Be sure to place the IntelliBeam microphone on an

imaginary center line drawn from this unit.

You may want to use the supplied cardboard microphone

stand to affix the IntelliBeam microphone at the same height

as your ears would be when you are seated in your listening

position.

Installing the IntelliBeam microphone

Notes

VOLUME

MIN MAX MIN

MAX

CROSSOVER

HIGH CUT

Subwoofer

STANDBY/ON

Front panel

Remote control

INTELLIBEAM MIC

Note

IntelliBeam

microphone

More than

1.8 m (6.0 ft)

Within 1 m (3.3 ft)

upper or lower

from the center

height

Cardboard

microphone stand

Sofa

Upper bound

position of the

microphone

Upper bound position

of the microphone

AUTO SETUP (IntelliBeam)

31 En

SETUP

English

■ Assembling the supplied cardboard

microphone stand

You will find three separate parts (one circular part and

two longitudinal parts) of the cardboard microphone stand

originally put together.

1 Disassemble the three parts of the cardboard

microphone stand originally put together.

2 Insert one of the longitudinal part into the

crevice of the other longitudinal part.

3 Place the circular part on top of the two

combined longitudinal parts.

4 Place the supplied IntelliBeam microphone

on top of the circular part.

Once the IntelliBeam microphone is firmly connected to

this unit and properly placed in your listening room,

follow the procedure below to start the AUTO SETUP

procedure.

You can also enter the AUTO SETUP procedure simply by

pressing and holding AUTO SETUP for more than two

seconds. In this case, this unit performs both of the beam

optimization and sound optimization procedures.

IntelliBeam

microphone

Center line

Using AUTO SETUP (IntelliBeam)

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

ENTER

OFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

ENTRY

CAT/

A-E

321

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

+10

789

SUR. DECODE

MY SUR.

YSP

TV/AV

STANDBY/ON

VOLUME

INPUT

AUTO SETUP (IntelliBeam)

32 En

• Make sure that your listening room is as quiet as possible while

this unit is performing the AUTO SETUP procedure.

• To achieve the best results possible, evacuate yourself from

your listening room until the AUTO SETUP procedure is

completed so that you may not obstruct the path of sound

beams.

• Be advised that it is normal for loud test tones to be output

during the AUTO SETUP procedure.

• The AUTO SETUP procedure may not be run successfully if

this unit is installed in one of the rooms described in “Before

installing this unit” on page 13. In such cases, run MANUAL

SETUP (see page 74) to manually adjust the corresponding

parameters.

• If an error occurs, an error buzzer is played, the AUTO SETUP

procedure stops, and an error message appears on the screen.

See “Error messages for AUTO SETUP” on page 35 for

appropriate remedies.

• The AUTO SETUP procedure takes about three minutes

maximum. A chime is played when the AUTO SETUP

procedure is run successfully.

• If there are curtains in your listening room, we recommend

following the procedure below.

1. Open the curtains to improve sound reflection.

2. Run BEAM OPTIMZ only.

3. Close the curtains.

4. Run SOUND OPTIMZ only.

• You can save the settings optimized by the AUTO SETUP

procedure (see page 36). A set of settings optimized according

to the specific conditions of your listening environment can be

recalled later depending on the varying conditions of your

listening environment (see page 37).

1 Press STANDBY/ON to turn on the power of

this unit.

If a subwoofer is connected to this unit, turn on the

power of the subwoofer.

2 Set the operation mode selector to YSP.

3 Press MENU.

The SET MENU screen appears on your TV.

• The control buttons used for SET MENU are displayed at

the bottom of the screen.

• To return to the previous screen while using SET MENU,

press RETURN.

• To exit from the SET MENU screen, press MENU again.

• You can start the BEAM+SOUND OPTIMZ procedure

simply by pressing and holding AUTO SETUP for more

than two seconds. Steps 4 and 5 are skipped and then the

screen shown in step 5 is displayed on your TV. Start the

AUTO SETUP procedure from step 6.

• You can also perform the following operations in the front

panel display.

4 Press / to select AUTO SETUP and

press ENTER.

The following screen appears on your TV.

Notes

STANDBY/ON

Front panel

Remote control

YSP

TV/AV

;MEMORY

;AUTO SETUP

;MANUAL SETUP

;LANGUAGE SETUP

[ ]/[ ]:Up/Down

[ENTER]:Enter

SET MENU

1)BEAM+SOUND OPTIMZ

2)BEAM OPTIMZ only

3)SOUND OPTIMZ only

[ ]/[ ]:Up/Down

[ENTER]:Enter

;AUTO SETUP

ENTER

AUTO SETUP (IntelliBeam)

33 En

SETUP

English

5 Press / to select BEAM+SOUND

OPTIMZ, BEAM OPTIMZ only, or SOUND

OPTIMZ only and then press ENTER.

The following screen appears on your TV.

BEAM+SOUND OPTIMZ

(Beam optimization and sound optimization)

Use to optimize the beam angle, delay, volume, and

quality so that the parameters best match your listening

environment.

It is recommended that you should select this optimization

feature in the following cases:

• If you make settings for the first time.

• If the unit has been relocated.

• If your listening room has been restructured.

• If the objects in your listening room (furniture, etc.)

have been rearranged.

This menu takes about three minutes.

BEAM OPTIMZ only

(Beam optimization only)

Use to optimize the beam angle so that the parameter best

matches your listening environment.

This menu takes about one minute.

SOUND OPTIMZ only

(Sound optimization only)

Use to optimize the beam delay, volume, and quality so

that the parameters best match your listening environment.

It is recommended that you should select this optimization

feature in the following cases:

• If you have opened or closed the curtains in your

listening room before using this unit.

• If you have manually set the beam angle.

This menu takes about two minutes.

You must optimize the beam angle in the BEAM OPTIMZ only

procedure before starting the SOUND OPTIMZ only procedure.

6 Check the following points once again before

starting the AUTO SETUP procedure.

• Is the IntelliBeam microphone firmly connected to

this unit?

• Is the IntelliBeam microphone placed in a proper

location?

• Are there any large obstacles in between the

IntelliBeam microphone and the walls in your

listening room?

7 Press ENTER to start the AUTO SETUP

procedure.

The following screen appears on your TV and the

AUTO SETUP procedure starts in 10 seconds.

Leave the room quietly before starting the AUTO

SETUP procedure.

If an error occurs, an error buzzer is played and an

error message is displayed. See “Error messages for

AUTO SETUP” on page 35 for a complete list of

error messages and their proper remedies. Follow the

instructions and perform the AUTO SETUP

procedure again.

Note

ENTER

PREPARATION & CHECK

Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from the YSP

unit. The MIC should be set

at ear level when seated.

Measurement takes about 3min.

After [ENTER] is pressed,

please leave the room.

[ENTER]:Start [RETURN]:Cancel

AUTO SETUP

Will begin in 10sec

Please leave the room

**--------

[RETURN]:Cancel

AUTO SETUP START

ENTER

← Flashes

AUTO SETUP (IntelliBeam)

34 En

8 Check that the following screen is displayed

on your TV.

The results of the AUTO SETUP procedure are

displayed on your TV.

• If “ENVIRONMENT CHECK [FAILED]” is

displayed, we recommend running the AUTO SETUP

procedure again. For details, see step 9.

• If “SUBWOOFER : NOT APPLICABLE” is displayed

even though a subwoofer is connected to this unit,

increase the volume level of the subwoofer and run the

AUTO SETUP procedure again.

• Depending on the environment of your listening room,

the beam angle of front left and right, and surround left

and right may be set to the same value even if

“5 BEAM” is displayed as a result.

9 Press ENTER to confirm the results or press

RETURN to cancel the results.

The following screen is displayed for two seconds

and then disappears from your TV.

If “ENVIRONMENT CHECK [FAILED]” is displayed in

step 8, the following screen is displayed after pressing

ENTER. In this case, see ERROR E-1 in “Error messages

for AUTO SETUP” on page 35. Press ENTER to exit

AUTO SETUP and then run the procedure again from

step 3.

10 Disconnect the IntelliBeam microphone from

the INTELLIBEAM MIC jack on the front

panel.

If you want to save and load settings, see “Using the system

memory” on page 36.

MEASUREMENT COMPLETE

BEAM MODE :5 BEAM

SUBWOOFER :NOT APPLICABLE

[ENTER]:Save set-up.

[RETURN]:Do not save set-up.

SHOW RESULT

Example 1

MEASUREMENT COMPLETE

ENVIRONMENT CHECK[FAILED]

BEAM MODE :5 BEAM

SUBWOOFER :YES

[ENTER]:Save set-up.

[RETURN]:Do not save set-up.

SHOW RESULT

Example 2

←

Flashes

ENTER

AUTO SETUP COMPLETE

Please remove the MIC from

the YSP and the listening

position.

AUTO SETUP COMPLETE

Your YSP unit may not be set

up correctly.

We recommend you try again.

Please press [ENTER] key to

exit.

←

Flashes

AUTO SETUP (IntelliBeam)

35 En

SETUP

English

■ Error messages for AUTO SETUP

Before the AUTO SETUP procedure starts

While the AUTO SETUP procedure is in progress

If one of the errors listed below except E-1 is displayed, press RETURN. In case you have started the AUTO SETUP

procedure by pressing AUTO SETUP in step 3, run the procedure again from step 3 after the screen disappears. In case

you have started the AUTO SETUP procedure by pressing MENU in step 3, run the procedure again from step 4 after the

screen in step 3 is displayed. Run MANUAL SETUP if the problem is difficult to be solved.

Error message Cause Remedy

See

page

ERROR E-2

No MIC detected. Please check

MIC connection and re-try.

The IntelliBeam microphone is not

connected to this unit.

Connect the IntelliBeam microphone to

this unit.

Error message Cause Remedy

See

page

ERROR E-1

Please test in quieter environment.

There is too much unwanted noise in

your listening room.

Make sure that your listening room is as

quiet as possible. You may want to

choose certain hours during the day

when there is not much noise coming

from outside.

—

ERROR E-2

No MIC detected. Please check

MIC connection and re-try.

The IntelliBeam microphone was

disconnected while the AUTO SETUP

procedure was in progress.

Make sure that the IntelliBeam

microphone is firmly connected to this

unit.

ERROR E-3

Unexpected control is detected.

Please re-try.

Some other operations were performed

on this unit while the AUTO SETUP

procedure was in progress.

Do not perform any other operations

while the AUTO SETUP procedure is in

progress.

—

ERROR E-4

Please check MIC position. MIC

should be set in front of YSP.

The IntelliBeam microphone is not

placed in front of this unit.

Make sure that the IntelliBeam

microphone is installed in front of this

unit.

ERROR E-5

Please check MIC position. MIC

should be set above 1.8m/6.0ft.

The IntelliBeam microphone is not

placed in the right distance from this

unit.

Make sure that the IntelliBeam

microphone is installed more than 1.8 m

(6.0 ft) from the front of this unit and

within 1 m (3.3 ft) from the center height

of this unit.

ERROR E-6

Volume level is lower than

expected. Please check MIC

position/connection and re-try.

The IntelliBeam microphone cannot

collect the sound produced by this unit

because the sound output level is too low.

Make sure that the IntelliBeam

microphone is firmly connected to this

unit and placed in a proper location. If

the problem persists, contact the nearest

authorized Yamaha service center for

assistance.

ERROR E-7

Unexpected error happened.

Please re-try.

An internal system error occurred. Repeat the AUTO SETUP procedure.

—

USING THE SYSTEM MEMORY

36 En

You can save the current settings adjusted in SET MENU

in the system memory of this unit. It is handy to save

certain settings according to the varying conditions of

your listening environment. For example, if there are

curtains in the path of sound beams, the effectiveness of

the sound beams will vary depending on whether the

curtains are open or closed.

1 Set the operation mode selector to YSP.

2 Press MENU.

The SET MENU screen appears on your TV.

• The control buttons used for SET MENU are displayed at

the bottom of the screen.

• To return to the previous screen while using SET MENU,

press RETURN.

• To exit from the SET MENU screen, press MENU once

more.

• You can also perform the following operations in the front

panel display.

3 Press / to select MEMORY and press

ENTER.

The following screen appears on your TV.

4 Press / to select SAVE and press

ENTER.

The following screen appears on your TV.

Using the system memory

Convenient usage of the system

memory

Saving settings

When the curtains are

open

When the curtains are

closed

YSP

TV/AV

;MEMORY

;AUTO SETUP

;MANUAL SETUP

;LANGUAGE SETUP

[ ]/[ ]:Up/Down

[ENTER]:Enter

SET MENU

ENTER

1)LOAD

2)SAVE

[ ]/[ ]:Up/Down

[ENTER]:Enter

;MEMORY

ENTER

MEMORY1

MEMORY2

MEMORY3

[ ]/[ ]:Select

[ENTER]:Enter

2)MEMORY SAVE

ENTER

Using the system memory

37 En

SETUP

English

5 Press / to select MEMORY1,

MEMORY2, or MEMORY3 and press ENTER.

The following screen appears on your TV.

6 Press ENTER again.

The new parameters are saved as MEMORY1,

MEMORY2, or MEMORY3. Once the parameters

are saved, the display returns to the SET MENU

screen.

7 Press MENU to exit.

The SET MENU screen disappears from your TV.

You can recall the settings saved in “Saving settings” on

page 36 according to the varying conditions of your

listening environment.

1 Set the operation mode selector to YSP.

2 Press MENU.

The SET MENU screen appears on your TV.

• The control buttons used for SET MENU are displayed at

the bottom of the screen.

• To return to the previous screen while using SET MENU,

press RETURN.

• To exit from the SET MENU screen, press MENU once

more.

• You can also perform the following operations in the front

panel display.

3 Press / to select MEMORY and press

ENTER.

The following screen appears on your TV.

MEMORY1 Save Now ?

Push [ENTER] to Save

2)MEMORY SAVE

ENTER

MEMORY1 Saving

2)MEMORY SAVE

ENTER

;MEMORY

;AUTO SETUP

;MANUAL SETUP

;LANGUAGE SETUP

[ ]/[ ]:Up/Down

[ENTER]:Enter

SET MENU

Loading settings

YSP

TV/AV

;MEMORY

;AUTO SETUP

;MANUAL SETUP

;LANGUAGE SETUP

[ ]/[ ]:Up/Down

[ENTER]:Enter

SET MENU

ENTER

1)LOAD

2)SAVE

[ ]/[ ]:Up/Down

[ENTER]:Enter

;MEMORY

ENTER

Using the system memory

38 En

4 Press / to select LOAD and press

ENTER.

The following screen appears on your TV.

5 Press / to select MEMORY1,

MEMORY2, or MEMORY3 and press ENTER.

The following screen appears on your TV.

6 Press ENTER again.

The new parameters saved as MEMORY1,

MEMORY2, or MEMORY3 are loaded. Once the

parameters are loaded, the display returns to the SET

MENU screen.

7 Press MENU to exit.

The SET MENU screen disappears from your TV.

ENTER

MEMORY1

MEMORY2

MEMORY3

[ ]/[ ]:Select

[ENTER]:Enter

1)MEMORY LOAD

ENTER

MEMORY1 Load Now ?

Push [ENTER] to Load

1)MEMORY LOAD

ENTER

MEMORY1 Loading

1)MEMORY LOAD

ENTER

;MEMORY

;AUTO SETUP

;MANUAL SETUP

;LANGUAGE SETUP

[ ]/[ ]:Up/Down

[ENTER]:Enter

SET MENU

PLAYBACK

39 En

BASIC

OPERATION

English

You can play back sound from the components connected

to this unit simply by pressing INPUT on the front panel

repeatedly or pressing one of the input selector buttons

(TV/STB, DVD, AUX1, AUX2, AUX3, XM, or FM) on

the remote control. The name of the selected input source

and the type of corresponding input mode appear in the

front panel display.

■ Front panel operations

Press INPUT on the front panel repeatedly to

toggle between TV/STB, DVD, AUX1, AUX2,

AUX3, XM, and FM.

The name of the corresponding input source and the type

of current input mode are displayed in the front panel

display.

■ Remote control operations

In addition to controlling this unit, you can also operate other AV

components if you set up the remote control with the appropriate

remote control codes and set the operation mode selector to TV/

AV to change the control area (see page 94).

Press TV to play back a TV program.

Press STB to play back a satellite broadcast.

Press DVD to play back a DVD.

Playback

Selecting the input source

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

ENTER

OFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

ENTRY

CAT/

A-E

321

AUX1 AUX2

STB

DVD

AUX3

DOCK

+10

789

YSP

TV/AV

SUR. DECODE

MY SUR.

STANDBY/ON

VOLUME

INPUT

TV/STB AUTO

Name of the selected

input source

Type of the selected

input mode

STB

TV/STB AUTO

DVD

DVD AUTO

40 En

Playback

Press FM/XM to listening to FM (see “FM tuning”

on page 42) or XM Satellite Radio (see “XM™

Satellite Radio tuning” on page 47).

Press AUX1 (or AUX2) to play back a component

connected to the AUX 1 (or AUX 2) jack on the

rear panel of this unit.

Press AUX3 to play back a component connected

to the AUX 3 input jack on the front panel.

Once an input source is selected (see page 39), you can

play back the selected input source.

This section uses a DVD player as an example of the playback

source.

For details on your TV and DVD player, refer to the respective

owner’s manual.

1 Turn on the power of your DVD player.

2 Switch to the video input on your TV using

the remote control supplied with the TV and

display the DVD menu screen.

If necessary, turn down the volume of your TV until no

sound is heard.

3 Press DVD to select DVD as the input source.

4 Play back DVD on your DVD player using the

supplied remote control.

Audio signals from your DVD player are output from

this unit.

• You can use the supplied demonstration DVD to check the

digital signals being input at the DVD player with the digital

connection (optical/coaxial/HDMI). The input channel and LFE

indicators light up when this unit detects the 5.1-channel signal

input at the optical/coaxial/HDMI jack. If the indicator

lights up, confirm the settings of the digital output, bitstream

output, DTS output, and/or HDMI output of the DVD player.

• If the output volume is too low, increase the volume of this unit

to around 45.

• If you have set the appropriate remote control codes for your

TV and DVD player, you can use the remote control supplied

with this unit to operate these components. For details on how

to set remote control codes, see page 94.

Playing back sources

Note

FM/XM

AUX1

AUX1 AUTO

AUX3

Note

DVD

PCM

41 En

Playback

BASIC

OPERATION

English

Press VOLUME +/– to increase or decrease the

volume level.

The numeric value of the volume level appears in the front

panel display.

Control range: MIN (minimum), 01 to 99,

MAX (maximum)

• The volume level of all input sources (including multi-channel

as well as stereo sources) changes at the same time.

• One volume level increases or decreases each time you press

VOLUME +/–.

• You can continuously increase or decrease the volume level if

you press and hold VOLUME +/–.

■ Muting the sound

1 Press MUTE to mute the sound.

“AUDIO MUTE ON” appears in the front panel

display, and the volume level indicator flashes.

2 Press MUTE again (or press VOLUME +/–) to

resume the sound output.

“AUDIO MUTE OFF” appears temporarily in the

front panel display (or the numeric value of the

current volume level appears if you press VOLUME

+/–), and the volume level indicator lights up.

The sound output of all input sources (including multi-channel as

well as stereo sources) is muted at the same time.

You can select whether the sound output is to be muted

completely or by 20 dB when you press MUTE (see page 80).

Adjusting the volume

Notes

STANDBY/ON

VOLUME

INPUT

TV VOL

VOLUME

MUTE

TV INPUT TV MUTE

VOLUME

VOLUME 30

Front panel

Remote control

Note

TV VOL

VOLUME

MUTE

TV INPUT TV MUTE

CODE SET

DVD 5BEAM

MUTE

AUDIO MUTE ON

Flashes

AUDIO MUTE OFF

VOLUME

Lights up

MUTE

FM TUNING

42 En

There are two tuning methods: automatic and manual. Automatic tuning is effective when the radio signal is strong and

there is no interference. If the radio signal is weak, tune into the FM station manually. You can also use the automatic and

manual preset tuning features to store up to 40 stations in total (A1 to E8: 5 preset station groups with 8 preset station

numbers each).

When the operation mode selector is set to TV/AV, you can operate all FM functions. When the operation mode selector is set to YSP,

you can only operate the functions described in “Selecting a preset station” (see page 46).

Orient the connected FM antenna for the best reception.

■ Remote control functions

Set the operation mode selector (8) to TV/AV before

tuning or preset tuning.

1 FM/XM

Press FM/XM repeatedly to select FM as the input source.

This unit is tuned into the last selected FM station.

2 PRESET/TUNE

Switches between the preset search mode and the

frequency search mode (see page 45).

3 Numeric buttons

Use numbers 1 through 8 to select the preset station

numbers (see page 46).

4 ENTRY ( / )

• Selects the preset station numbers (1 to 8) when the

colon (:) is displayed in the front panel display

(see page 46).

• Selects the tuning frequency when the colon (:) is not

displayed in the front panel display (see page 43).

5 CAT/A-E ( / )

Selects the preset station groups (A to E) (see page 45).

6 MEMORY

• Stores a preset station in the memory (see page 45).

• Hold down this button for more than three seconds to

start automatic preset tuning (see page 44).

7 SEARCH

Switches between automatic tuning (the AUTO indicator

is turned on) and manual tuning (the AUTO indicator is

turned off) (see page 43).

8 Operation mode selector

Selects the operation mode of this unit.

FM tuning

Note

FM controls and functions

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

TV INPUT TV MUTE

ENTER

OFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

ENTRY

CAT/

A-E

321

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

+10

789

YSP

TV/AV

SUR. DECODE

MY SUR.

43 En

FM tuning

BASIC

OPERATION

English

Automatic tuning is effective when the radio station

signals are strong and there is no interference.

1 Set the operation mode selector to TV/AV.

2 Press FM/XM repeatedly to select FM as the

input source.

“FM” appears in the front panel display.

• You can also press INPUT on the front panel repeatedly to

select FM as the input source.

• If “XM” appears in the front panel display, press FM/XM

again to display “FM”.

3 Press SEARCH repeatedly until the AUTO

indicator lights up in the front panel display.

If a colon (:) appears in the front panel display, tuning

is not available. Press PRESET/TUNE to turn the

colon (:) off.

4 Press ENTRY ( / ) once to begin

automatic tuning.

When this unit is tuned into an FM station, the

TUNED indicator lights up and the frequency of the

station appears in the front panel display.

• Press to tune into a higher frequency.

• Press to tune into a lower frequency.

If the desired FM station signal is weak, tune into it

manually.

Manual tuning automatically switches the tuner to the monaural

reception mode to increase the signal quality.

1 Set the operation mode selector to TV/AV.

2 Press FM/XM repeatedly to select FM as the

input source.

“FM” appears in the front panel display.

• You can also press INPUT on the front panel repeatedly to

select FM as the input source.

• If “XM” appears in the front panel display, press FM/XM

again to display “FM”.

Automatic tuning

YSP

TV/AV

FM/XM

A FM 88.9 MHz

Lights up

No colon (:)

Manual tuning

Note

ENTER

ENTRY

YSP

TV/AV

FM/XM

44 En

FM tuning

3 Press SEARCH repeatedly until the AUTO

indicator disappears from the front panel

display.

If a colon (:) appears in the front panel display, tuning

is not available. Press PRESET/TUNE to turn the

colon (:) off.

4 Press ENTRY ( / ) to tune into the

desired station manually.

Hold down the button for quick search.

You can use the automatic preset tuning feature to store up

to 40 FM stations with strong signals (A1 to E8: 5 preset

station groups with 8 preset station numbers each). You

can recall the preset stations easily by selecting the preset

station groups and numbers.

1 Set the operation mode selector to TV/AV.

2 Press FM/XM repeatedly to select FM as the

input source.

“FM” appears in the front panel display.

• You can also press INPUT on the front panel repeatedly to

select FM as the input source.

• If “XM” appears in the front panel display, press FM/XM

again to display “FM”.

3 Press and hold MEMORY for more than three

seconds.

The preset station group and number, the MEMORY

indicator, and the AUTO indicator flash. Automatic

preset tuning starts from the lowest frequency and

proceeds toward higher frequencies.

When automatic preset tuning is completed, the front

panel display shows the frequency of the last preset

station.

• When you overwrite an existing preset station, the

previously stored FM station is cleared.

• If the number of automatically preset stations does not

reach 40 (E8), this unit automatically stops searching.

• Only FM stations with sufficient signal strength are preset

automatically. If the desired station is weak in signal

strength, tune into it manually and store it as described in

“Manual preset tuning” on page 45.

Automatic preset tuning

A FM 88.9 MHz

No colon (:)

ENTER

ENTRY

YSP

TV/AV

Notes

FM/XM

A1:FM 88.9 MHz

Flashes

MEMORY

45 En

FM tuning

BASIC

OPERATION

English

You can also store up to 40 stations (A1 to E8: 5 preset

station groups with 8 preset station numbers each)

manually.

1 Set the operation mode selector to TV/AV.

2 Tune into the desired FM station.

See page 43 for tuning instructions.

3 Press MEMORY.

The MEMORY indicator flashes in the front panel

display for approximately 10 seconds.

4 Press CAT/A-E ( / ) repeatedly to select a

preset station group (A to E) while the

MEMORY indicator is flashing.

The selected preset station group letter appears.

5 Press ENTRY ( / ) to select a preset

station number (1 to 8) while the MEMORY

indicator is flashing.

You can also use the numeric buttons to select the desired

preset station number and complete the manual preset

tuning procedure. In this case, skip step 6.

6 Press MEMORY while the MEMORY indicator

is flashing.

The preset station group and number appear in the

front panel display together with the station band and

frequency. The MEMORY indicator disappears from

the front panel display.

• When you overwrite an existing preset station, the

previously stored FM station is cleared.

• The reception mode (stereo or monaural) is stored along

with the station frequency.

Manual preset tuning

YSP

TV/AV

Flashes

MEMORY

A :FM 88.9 MHz

ENTER

CAT/

A-E

Preset

station

group

Flashes

Notes

A1:FM 88.9 MHz

Preset station number

ENTER

ENTRY

Flashes

A1:FM 88.9 MHz

The displayed station has been stored as A1.

MEMORY

46 En

FM tuning

You can tune into the preset stations simply by selecting

the preset station groups and numbers.

1 Set the operation mode selector to TV/AV.

2 Press FM/XM repeatedly to select FM as the

input source.

“FM” appears in the front panel display.

• You can also press INPUT on the front panel repeatedly to

select FM as the input source.

• If “XM” appears in the front panel display, press FM/XM

again to display “FM”.

3 Press CAT/A-E ( / ) to select the desired

preset station group (A to E).

The preset station group letter appears in the front

panel display and changes each time you press the

button.

• If the colon (:) does not appear, press PRESET/TUNE to

display the colon.

• Even when the operation mode selector is set to YSP, you

can select the desired preset group by pressing CAT.

4 Press ENTRY ( / ) to select the desired

preset station number (1 to 8).

The preset station group and number appear in the

front panel display together with the station band and

frequency.

• You can also use the numeric buttons to select the desired

preset station number.

• Even when the operation mode selector is set to YSP, you

can select the desired preset number by pressing

a (SEARCH) /5 (MEMORY).

Selecting a preset station

YSP

TV/AV

FM/XM

ENTER

CAT/

A-E

ENTER

ENTRY

A1:FM 88.9 MHz

XM™ SATELLITE RADIO TUNING

47 En

BASIC

OPERATION

English

■ About XM Satellite Radio

XM Satellite Radio offers an extraordinary variety of commercial-free music, plus the best in sports, news, talk, and

entertainment. XM is broadcast in superior digital audio from coast to coast. From rock to reggae, from classical to hip

hop, XM has something for every music fan. XM’s dedication to playing the richest selection of music is matched by its

passion for live sporting events, talk radio, up-to-the-minute news, stand-up comedy, children’s programming, and much

more.

This unit is equipped with the Neural Surround decoder that plays back the XM HD surround sound content of the XM Satellite Radio

broadcasts in multi-channels, resulting in a full surround sound experience. See “Surround modes and recommended sources” (see page

56).

The XM Satellite Radio service is unavailable in Alaska and Hawaii.

Connect XM Mini-Tuner and Home Dock (each sold

separately by XM Satellite Radio) to the XM jack on the

rear panel of this unit. For information on your XM Mini-

Tuner and Home Dock, see the operating instructions

provided with XM Mini-Tuner Home Dock.

• To ensure optimal reception of the XM Satellite Radio signals,

the antenna of Home Dock must be placed at or near a south-

facing window with no obstacles in the path to the sky. You can

mount it indoors or outdoors.

• Use the “XM ANTENNA LEVEL” parameter in “MANUAL

SETUP” (see page 82) to display the XM Satellite Radio

reception level (%) in the OSD. For the best reception, adjust

the orientation of the connected indoor antenna of the Home

Dock to obtain a value of 60% or more.

If “CHECK ANTENNA” appears in the front panel display,

Home Dock may not be connected properly to the XM jack on the

rear panel of this unit.

XM™ Satellite Radio tuning

XM READY

Legal Disclaimer

Hardware and required monthly subscription sold separately. Other fees and taxes, including a one-time activation fee may apply.

Subscription fee is consumer only. All fees and programming subject to change. Channels with frequent explicit language are indicated with

an XL. Channel blocking is available for XM radio receivers by calling 1-800-XMRADIO (US residents) and 1-877-GET-XMSR (Canadian

residents). For a full listing of the XM commercial-free channels and advertising-supported channels, visit lineup.xmradio.com (US

residents) or www.xmradio.ca (Canadian residents). Subscriptions subject to Customer Agreement available at xmradio.com (US residents)

Note

Connecting XM™ Mini-Tuner Home Dock

DIGITAL INPUT

TV/STB

DVD

IR INXMAUX1

AUX 2

COAXIAL

OPTICAL

XM Mini-Tuner and Home Dock

(each sold separately)

Rear panel of this unit

Note

48 En

XM™ Satellite Radio tuning

Once you have installed XM Mini-Tuner Home Dock,

inserted XM Mini-Tuner, connected Home Dock to your

XM READY home audio system, and installed the

antenna, you are ready to subscribe and begin receiving

XM programming. There are three places to find your

eight-character XM Radio ID: on XM Mini-Tuner, on XM

Mini-Tuner package, and on XM Channel 0 (see “All

Channel Search mode” on page 49). Record the XM

Radio ID in the following eight squares for reference.

The XM Radio ID does not use the letters “I”, “O”, “S”, or “F”.

Activate your XM Satellite Radio service in the U.S. online at

http://www.xmradio.com/ or call 1-800-XM-RADIO (1-800-967-

2346). You will need a major credit card. XM will send a signal

from the satellites to activate the full channel lineup. Activation

normally takes 10 to 15 minutes, but during peak busy periods

you may need to keep your XM READY home audio system on

for up to an hour. When you can access the full channel lineup on

your XM READY home audio system, you are done. For more

information or to subscribe in Canada, visit XM on the Web at

http://www.xmradio.ca/ or call XM’s Listener Care at 1-877-

GET-XMSR (1-877-438-9677).

1 Set the operation mode selector to

TV/AV.

2 Press FM/XM repeatedly to select XM as the

input source.

In the front panel display, the XM indicator lights up

and the XM Satellite Radio information (channel

number/channel name, channel category, and artist

name/song or program title) for the currently selected

channel appears.

• You can also press INPUT on the front panel repeatedly to

select XM as the input source.

• When XM is selected as the input source, this unit

automatically recalls the previously chosen channel.

Activating XM™ Satellite Radio

Note

Basic XM™ Satellite Radio

operations

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

ENTER

SUR. DECODEOFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MY SUR.

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

ENTRY

CAT/

A-E

321

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

+10

789

TV/AV

YSP

TV/AV

[001] Preview

Lights up

FM/XM

49 En

XM™ Satellite Radio tuning

BASIC

OPERATION

English

3 Search for a desired channel by using one of

the four XM Satellite Radio search modes:

• To select a channel from all channels, see “All

Channel Search mode” on this page.

• To select a channel by channel category, see

“Category Search mode” on this page.

• To select a channel from the preset channels, see

“Preset Search mode” on page 50.

• To select a channel by directly entering the channel

number, see “Direct Number Access mode” on

page 50.

• You can preset the XM Satellite Radio channels (see page 51).

• You can display the XM Satellite Radio information in the front

panel display and/or in the OSD (see page 52).

■ All Channel Search mode

1 Press SEARCH repeatedly to select “ALL CH

SEARCH”.

2 Press ENTRY ( / ) repeatedly to search

for an XM channel within all channels.

• Hold down ENTRY ( / ) for quick search.

• To change the channel category, press CAT/A-E ( / ).

• Select channel “0” to display your XM Radio ID number.

■ Category Search mode

1 Press SEARCH repeatedly to select “CAT

SEARCH”.

2 Press CAT/A-E ( / ) repeatedly to change

the XM channel category.

3 Press ENTRY ( / ) repeatedly to search

for an XM channel within the selected

channel category.

Hold down ENTRY ( / ) for quick search.

ALL CH SEARCH

ENTER

ENTRY

CAT SEARCH

ENTER

CAT/

A-E

ENTER

ENTRY

50 En

XM™ Satellite Radio tuning

■ Preset Search mode

Prior to selecting a preset channel in the Preset Search

mode, you must preset the XM channels. For details, see

“Presetting the XM™ Satellite Radio channels” on

page 51.

1 Press SEARCH repeatedly to select

“PRESET SEARCH”.

2 Press CAT/A-E ( / ) repeatedly to change

the preset channel group (A to E).

3 Press ENTRY ( / ) repeatedly to

change the preset channel number (1 to 8).

You can also use the numeric buttons to directly input the preset

channel number.

■ Direct Number Access mode

1 Press SEARCH repeatedly to select either

“ALL CH SEARCH” or “CAT SEARCH”.

2 Press the numeric buttons (0 to 9) to enter

the desired three-digit XM channel number.

For example, to enter the number 123, press the

numeric buttons 1, 2, and 3.

The front panel display changes as follows:

• To enter a one- or two-digit number, press the corresponding

number button(s), and press ENTER to confirm the number. If

you do not press ENTER, this unit automatically confirms the

entered number after a few seconds.

• If you press a button other than the numeric buttons and

ENTER during this operation, the Direct Number Access mode

is canceled.

PRESET SEARCH

ENTER

CAT/

A-E

ENTER

ENTRY

Notes

ALL CH SEARCH

CAT SEARCH

5BEAM

ST+3BEAM

3BEAM

<XM> --1

<XM> -12

<XM> 123

51 En

XM™ Satellite Radio tuning

BASIC

OPERATION

English

You can use this feature to store up to 40 XM Satellite

Radio channels (A1 to E8: 5 preset channel groups with 8

preset channel numbers each). You can then recall the

preset channels easily by selecting the preset group and

number as described in “Preset Search mode” on page 50.

1 Search for an XM channel that you want to

preset.

See “Basic XM™ Satellite Radio operations” on

page 48 for details.

The initial factory setting for all preset channels is “[001]

Preview”.

2 Press MEMORY.

The MEMORY indicator flashes in the front panel

display for about 10 seconds.

Operate steps 3 to 5 while the MEMORY indicator is flashing.

3 Press CAT/A-E ( / ) repeatedly to select a

preset group while the MEMORY indicator is

flashing.

The selected preset group appears in the front panel

display.

4 Press ENTRY ( / ) repeatedly to select

a preset number while the MEMORY indicator

is flashing.

The selected preset number appears in the front panel

display.

5 Press MEMORY or ENTER to assign the

preset group and number to the selected XM

channel while the MEMORY indicator is

flashing.

A colon (:) appears, and the MEMORY indicator

turns off in the front panel display.

When you overwrite an existing preset channel, the previously

stored XM channel information is cleared and updated.

Presetting the XM™ Satellite

Radio channels

Note

[043] XMU

Currently selected channel number

Flashes

MEMORY

Currently selected preset group

Flashing

ENTER

CAT/

A-E

C [043] XMU

Note

C8 [043] XMU

Currently selected preset number

Flashing

ENTER

ENTRY

Colon (:)

MEMORY

ENTER

C8: [043] XMU

Colon (:)

52 En

XM™ Satellite Radio tuning

You can display the XM Satellite Radio information

(channel number/channel name, channel category, and

artist name/song or program title) for the currently

selected channel in the front panel display or in the OSD.

If a status or error message appears in the front panel display or in

the OSD, see the “XM Satellite Radio” in “Troubleshooting” on

page 100.

■ Displaying the XM channel information

in the front panel display

Press DISPLAY repeatedly to toggle between the

following information displays.

When the channel number / channel name is

displayed:

When the channel category is displayed:

When the artist name / song title is displayed:

• You can set the front panel display mode: CONT. or ONCE.

When ONCE is selected, the front panel display scrolls

characters to the end once, after which the first 15 characters

appear and stay. See “SCROLL” (Front panel display scroll) in

“F.DISPLAY SET” (Front panel display settings) (page 83).

• Undisplayable characters are displayed as spaces.

■ Displaying the XM channel information

in the OSD

Press DISPLAY.

The following screen is displayed in the OSD.

• To turn off the OSD, press DISPLAY again.

• You can set the interval for which the OSD screen is displayed

after an operation. See “OSD DISPLAY TIME” (OSD display

time) in “OSD SET” (OSD settings) (page 83).

• To hold the XM Satellite Radio OSD information, press

ENTER. To unhold, press ENTER again.

• This unit can save up to two XM Satellite Radio OSD

information screens for future reference. To view the previous

OSD screens, press RETURN repeatedly while the current XM

Satellite Radio OSD information screen is on hold.

Displaying the XM™ Satellite

Radio information

Note

Channel number / Channel name

Artist name / Song or program title

DISPLAY

Channel category

[043] XMU

<CAT>ROCK

Coldplay / Spee

XM INFORMATION

ALL CH SEARCH

XM :043

CHAN :XMU

CAT :Rock

NAME :Coldplay

TITLE:Speed of sound

.(Coldplay/Spe)

[ ]/[ ]:CHANNEL

[ ]/[ ]:CATEGORY

DISPLAY

USING IPOD™

53 En

BASIC

OPERATION

English

This unit has the DOCK terminal on the rear panel that allows you to connect the Yamaha iPod universal dock (such as

YDS-10, sold separately). Station your iPod in the Yamaha iPod universal dock, and use the supplied remote control to

operate your iPod.

• Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.

• Some features may not be compatible depending on the model or the software version of your iPod.

Connect the Yamaha iPod universal dock to the DOCK

terminal of this unit using a dedicated cable.

Do not connect this unit or other components to the main power

until all connections between components are complete.

When your iPod and external component using the AUX 3 input

jack are connected to this unit at the same time, and when the

DOCK indicator is lit in the front panel display, iPod output takes

priority.

1 Navigate through the iPod menu ( / / / ) and

starts playback (ENTER).

2 Displays the OSD (on-screen menu) menu.

3 Selects AUX3/DOCK as the input source.

4 Use to return to the previous iPod menu.

5 Sets the operation mode of this unit.

6 Use to return to the previous iPod menu.

7 Stops playback.

8 Pauses playback.

9 Searches forward/backward.

0 Starts playback.

Skips to the beginning of the current/previous/next track.

8 and 9 toggle between play and pause operations in the Simple

Remote mode.

Using iPod™

Notes

Connection

CAUTION

OUT

SUBWOOFER

TV/STB

AUX 1

VIDEO

DOCK

AUDIO INPUTANTENNA

Yamaha iPod universal dock

(such as YDS-10, sold separately)

Rear panel of this unit

Controlling iPod™

ENHANCER

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

SUR. DECODE

OFF

CODE SET

+10

YSP

TV/AV

ENTRY

CAT/

A-E

RETURNDISPLAY

MACRO

INPUT1

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

54 En

Using iPod™

• For a complete list of status messages that appear in the front panel display and in the OSD, see the “iPod” section in

“Troubleshooting” on page 100.

• While your iPod is stationed in the Yamaha iPod universal dock connected to the DOCK terminal of this unit, your iPod battery is

automatically charged as long as this unit is turned on.

■ Controlling iPod in the Simple Remote

mode

You can perform some basic operations such as play,

pause, stop, backward/forward search, and track skip

using the remote control without the aid of the OSD. Such

basic operations can be performed also on your iPod.

1 Set the operation mode selector to TV/AV.

2 Press AUX3/DOCK, and set your iPod in the

Yamaha iPod universal dock.

In the front panel display, “iPod connected” appears

and the DOCK indicator lights up.

• You can view the photos or video clips stored on your iPod in

the iPod screen (some models only).

•Use

# and * on the remote control interchangeably to toggle

between play and pause operations.

Information on the current song appears only in the iPod screen

but not in the front panel display of this unit.

■ Controlling iPod in the Menu Browse

mode

You can perform the advanced operations using the remote

control with the aid of the OSD. In the OSD, you can

browse the song list stored on your iPod. Further, you can

change or adjust the settings on your iPod as desired. Such

advanced operations cannot be performed on your iPod.

1 Set the operation mode selector to TV/AV.

2 Press AUX3/DOCK, and set your iPod in the

Yamaha iPod universal dock.

In the front panel display, “iPod connected” appears

and the DOCK indicator lights up.

3 Press DISPLAY, and display the menu

browse mode.

The OSD appears on your TV.

Note

YSP

TV/AV

iPod connected

Lights up

YSP

TV/AV

iPod connected

Lights up

DISPLAY

Playlists

Artists

Albums

Songs

Genres

Composers

Settings

iPod Top

55 En

Using iPod™

BASIC

OPERATION

English

4 Press / and / to navigate through

the iPod menu, and press ENTER to start

playback of the selected song.

Choices: Playlists (playlists), Artists (artists), Albums

(albums), Songs (songs), Genres (genres),

Composers (composers), Settings (settings)

• Playlists > Songs

• Artists > Albums > Songs

• Albums > Songs

• Songs

• Genres > Artists > Albums > Songs

• Composers > Albums > Songs

• Settings > Shuffle, Repeat

Settings parameters:

Shuffle Shuffle

Use this function for random playback of songs or albums.

When “Songs” or “Albums” is chosen, “S” appears in the

top right corner while the songs or albums are being

shuffled. Press ENTER repeatedly to toggle between the

choices.

Choices: Off, Songs, Albums

• Select “Off” to deactivate this function.

• Select “Songs” for random playback of songs.

• Select “Albums” for random playback of albums.

Repeat Repeat

Use this function for repeated playback of a song or a

sequence of songs. When “One” or “All” is chosen, “R”

appears in the top right corner while a song or a sequence

of songs are being repeated. Press ENTER repeatedly to

toggle between the choices.

Choices: Off, One, All

• Select “Off” to deactivate this function.

• Select “One” for repeated playback of a song.

• Select “All” for repeated playback of a sequence of

songs.

• Press RETURN or MENU to go back to the previous menu.

• The information on the current song also appears in the front

panel display. You can set the front panel display mode: CONT.

or ONCE. For details, see “SCROLL” (Front panel display

scroll) in “F.DISPLAY SET” (Front panel display settings) (see

page 83).

• You can set the interval for which the OSD screen is displayed

after an operation. See “OSD DISPLAY TIME” (OSD display

time) in “OSD SET” (OSD settings) (see page 83).

• You can view the photos or video crips stored on your iPod in

the OSD (some models only).

• The YAMAHA logo appears in the iPod screen in this mode.

• Undisplayable characters are shown as underscores “_” in the

front panel display and OSD.

• You can change or adjust the “Settings” parameters only in the

OSD.

■ An example of the information display

during playback

1 Track number/total tracks

2 Name of the artist

3 Name of the album

4 Name of the song

5 Progress bar

6 Elapsed time

7 Shuffle and repeat icons

8 (playback), (pausing),

(search forward),

and (search backward)

9 Remaining time

ENTER

and

Notes

iPod[Play] S R

1/9



||||||||;;;;;;;;;;;;

0:51-7:44

FrankieZipper

Made-to-order

RoadtoIndia

ENJOYING SURROUND SOUND

56 En

You can enjoy multi-channel surround sound by changing the beam mode using the beam mode buttons on the remote

control. Select 5 Beam, Stereo plus 3 Beam, 3 Beam, or My Surround for multi-channel playback.

• When ANGLE TO WALL OR CORNER is set in MANUAL SETUP (see page 76), 5 Beam and 3 Beam cannot be selected.

• To enjoy 5 Beam, Stereo plus 3 Beam, or 3 Beam as the beam mode, you must perform AUTO SETUP or MANUAL SETUP so that

the parameters best match your listening environment.

1 Set the operation mode selector to YSP.

2 Press one of the beam mode buttons

(5BEAM, ST+3BEAM, 3BEAM, or MY SUR.) to

select the desired beam mode for 5.1-

channel play back.

Outputs sound beams from the front left, front right,

center, surround left, and surround right channels. This

mode is ideal for enjoying surround sound effects to the

fullest when you watch DVDs recorded in a multi-channel

format or play back 2-channel sources in a multi-channel

format.

Press 5BEAM to select 5 Beam.

• To achieve the best surround sound effect, make sure that there

are no obstacles placed in the path of sound beams in that the

objects may prevent the sound beams from rebounding directly

off the walls in your listening room.

• The front left and right sound beams are output toward the walls

in your listening room.

• “SP Pos. Corner!” appears in the front panel display if

INSTALLED POSITION is set to ANGLE TO WALL OR

CORNER (see page 76).

Enjoying surround sound

Notes

STEREO MY SUR.

MY BEAM

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

ENTER

SUR. DECODE

OFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

ENTRY

CAT/

A-E

321

+10

789

YSP

TV/AV

YSP

TV/AV

5BEAM

ST+3BEAM

3BEAM

MY SUR.

5 Beam

Notes

5BEAM

57 En

Enjoying surround sound

BASIC

OPERATION

English

Outputs normal sound from the front left and right

channels and sound beams from the center and surround

left and right channels. This mode is ideal for watching

live recordings on a DVD. Vocals and instrumental sounds

can be heard close to the center of the listening position

while sound reflections from the venue itself can be heard

on your right and left, giving you the feeling that you are

sitting right in front of the stage.

Press ST+3BEAM to select Stereo plus 3 Beam.

The front left and right sound beams are output directly toward

the listening position.

Outputs sound beams from the front left and right and

center channels. This mode is ideal for enjoying movies

with the whole family. Because the listening position area

is widened, you can enjoy excellent quality surround

sound over a wider area. In addition, you can use this

mode when the listening position is close to the backside

of the wall, and the surround left and right sound beams

cannot be reflected off the wall.

Press 3BEAM to select 3 Beam.

You can achieve a more realistic surround effect if you adjust

settings for IMAGE LOCATION in BEAM MENU (see page 79).

• When you play back multi-channel sources, surround left and

right signals are mixed down and output from the front left and

right channels.

• The front left and right sound beams are output toward the walls

in your listening room.

• “SP Pos. Corner!” appears in the front panel display if

INSTALLED POSITION is set to ANGLE TO WALL OR

CORNER (see page 76).

This mode enables surround system in a small listening

area which may not fulfill the listening room conditions

for other beam modes (see “Before installing this unit” on

page 13). Use this beam mode when you want to enjoy

surround sound near this unit, or when the other beam

modes are unavailable.

Press MY SUR. to select My Surround.

• Beam mode settings such as beam angles and distances are

ineffective in this mode.

• For the full effect of My Surround, your listening position must

face toward the front of this unit.

Stereo plus 3 Beam

Note

3 Beam

ST+3BEAM

3BEAM

Notes

My Surround

Notes

MY SUR.

58 En

Enjoying surround sound

■ Decoder indicators

Depending on the input source and the selected surround

mode, the decoder indicators in the front panel display

light up as follows:

• You can select an input mode (AUTO, DTS, or ANALOG) by

pressing INPUTMODE repeatedly (see page 90).

• Discs encoded in DTS-ES, Dolby Digital 5.1 EX, Dolby Digital

EX, or Dolby Digital Surround EX will be played back in DTS

or Dolby Digital.

■ Input channel indicators

Depending on the channel component of the current

digital input signal, the input channel indicators in the

front panel display light up as follows:

■ Surround modes and recommended

sources

• When you select an input source (see page 39), the surround

mode used for the previously selected input source is

automatically selected.

• If the power of this unit is turned off and on again, the surround

mode used for the previously selected input source before the

power was turned off is automatically selected.

• If the surround modes are not available, “Prohibit” appears in

the front panel display when you press SUR. DECODE.

• The surround modes are available:

– when the beam mode is set to a setting other than the 2-

channel or 5-channel stereo playback (see page 62) and My

Surround (see page 57).

– when the CINEMA DSP programs are turned off

(see page 67).

– when the movie program is selected as the CINEMA DSP

program (see page 66). In this case, only Dolby Pro Logic,

Dolby Pro Logic II Movie, and DTS Neo:6 Cinema are

available.

– when 2-channel signals are being input.

– when the Music Enhancer is turned off (see page 68).

Status Indicator

When PCM signals are being input

When DTS digital signals are being

input

When DTS Neo:6 is selected as the

surround mode

When Dolby Digital signals are

being input

When Dolby Pro Logic is selected

as the surround mode

When Dolby Pro Logic II is selected

as the surround mode

Status Indicator

When 2-channel stereo signals are

being input

When 5.1-channel signals are being

input

PCM

DIGITAL

Surround mode

Recommended

source

Dolby Pro Logic – All sources

Dolby Pro Logic II

Movie

Music

Game

Movies

Music

Games

DTS Neo:6

Cinema

Music

Movies

Music

Neural Surround – XM Satellite Radio

Notes

59 En

Enjoying surround sound

BASIC

OPERATION

English

This unit can decode 2-channel sources for 5.1-channel

playback so that you can enjoy a variety of surround sound

effects by switching the surround mode.

The surround modes are available only when the CINEMA DSP

programs are turned off (see page 67) or when the movie program

is selected as the CINEMA DSP program (see page 66). In

addition, the beam mode must be set to 5 Beam, Stereo plus 3

Beam, or 3 Beam (see page 56), while the Music Enhancer must

be also turned off (see page 68).

1 Set the operation mode selector to YSP.

2 Press SUR. DECODE repeatedly (or press

SUR. DECODE and then press / ) to

switch between surround modes.

Choices: Neo:6 Cinema, Neo:6 Music, PRO LOGIC,

PLII Movie, PLII Music, PLII Game, neural surround

Default setting: Neo:6 Cinema

Enjoying 2-channel sources

in surround sound

STEREO MY SUR.

MY BEAM

ENHANCER MENU

RETURNDISPLAY

ENTER

SUR. DECODE

OFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

ENTRY

CAT/

A-E

321

+10

789

YSP

TV/AV

YSP

TV/AV

SUR. DECODE

ENTER

Neo:6 Cinema

Neo:6 Music

PRO LOGIC

PLII Movie

PLII

Music

PLII

Game

neural surround

Example of the surround

mode display in the front

panel display when the

CINEMA DSP program

and the Music Enhancer

are turned off

60 En

Enjoying surround sound

You can enjoy analog audio signals output from your TV

in real surround sound.

Before performing the steps below, set the volume of this unit to

30. If necessary, adjust the volume level in step 5 below.

1 Select the TV channel you want to watch.

To select a TV channel, use the remote control

supplied with your TV.

2 Set the operation mode selector to YSP.

3 Press TV.

This unit outputs audio signals from your TV.

4 If you hear sound from your TV speakers,

reduce the volume level of your TV until you

can no longer hear any audio being output.

To reduce the TV volume level, use the remote

control supplied with your TV.

5 Press VOLUME +/– to adjust the volume

level.

6 Press SUR. DECODE repeatedly (or press

SUR. DECODE and then press / ) to

switch between surround modes.

Signals input from 2-channel sources are played back

in multi-channels.

For more information on surround modes, see

page 58.

Enjoying TV in surround sound

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

ENTER

SUR. DECODE

OFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MY SUR.

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

ENTRY

CAT/

A-E

321

STB

+10

789

YSP

TV/AV

YSP

TV/AV

VOLUME

SUR. DECODE

ENTER

61 En

Enjoying surround sound

BASIC

OPERATION

English

You can configure the parameters for Dolby Pro Logic II

Music and DTS Neo:6 Music to fine-tune the surround

sound effect.

1 Repeat steps 1 and 2 in “Enjoying 2-channel

sources in surround sound” on page 59 and

select PL II Music or Neo:6 Music.

2 Press / to select the parameter.

3 Press / to configure the selected

parameter.

■ When Dolby Pro Logic II Music is

selected

PANORAMA

Gives the front left and right channel sound a

wraparound effect, distributed throughout the entire

surround sound field to give you an expansive feeling.

Choices: ON/OFF

Default setting: OFF

DIMENSION

Adjusts the difference in volume between the front

and surround channels to the desired volume balance.

Control range: –3 (toward the surround direction) to

+3 (toward the front direction)

Default setting: STD (standard)

C. WIDTH

Distributes the center channel sound to the left and

right. If 0 is selected, the center channel sound is

output only from the center channel.

Control range: 0 to 7

Default setting: 3

■ When DTS Neo:6 Music is selected

C. IMAGE

Adjusts the center image from three channels (front

left and right and center) to varying degrees.

Control range: 0.0 (wider) to 1.0 (toward the center)

Default setting: 0.3

Adjusting surround mode

parameters

ENHANCER MENU

RETURNDISPLAY

ENTER

SUR. DECODE

OFF

SPORTSMUSIC MOVIE

ENTRY

CAT/

A-E

+10

789

YSP

TV/AV

ENTER

ENJOYING STEREO SOUND

62 En

You can enjoy 2-channel and 5-channel stereo playback as the beam modes by pressing STEREO on the remote control.

• When you play back Dolby Digital audio signals in the 2-channel or 5-channel stereo playback, the dynamic range becomes

compressed. If the volume level decreases to the extreme, use other beam modes except My Beam.

• When the 2-channel or 5-channel stereo playback is selected as the beam mode, the surround modes (see page 58) and the CINEMA

DSP programs (see page 65) become ineffective.

Sounds are output from the front right and left channels.

This is ideal for playing back hi-fi sources, such as CDs,

and can be used to replace your TV speakers.

1 Set the operation mode selector to YSP.

2 Press STEREO to select the 2-channel stereo

playback as the beam mode.

“STEREO” appears in the front panel display.

When you play back multi-channel sources, all signals except

those from the front left and right channels are mixed down and

output from the front left and right channels. No audio is output

from the center and surround channels.

Sounds are output from front left and right, center, and

surround left and right. This is ideal for playback in a large

listening area or at a party.

1 Set the operation mode selector to YSP.

2 Press STEREO twice to select the 5-channel

stereo playback as the beam mode.

“5CH STEREO” appears in the front panel display.

Enjoying stereo sound

Notes

2-channel stereo playback

STEREO

MY BEAM MY SUR.

ENHANCER MENU

RETURNDISPLAY

ENTER

SUR. DECODEOFF

SPORTS

MUSIC MOVIE

ENTRY

CAT/

A-E

321

+10

789

YSP

TV/AV

YSP

TV/AV

STEREO

Note

5-channel stereo playback

YSP

TV/AV

STEREO

5CH STEREO

PLAYING BACK SOUND CLEARLY (MY BEAM)

63 En

BASIC

OPERATION

English

You can improve listenability in a noisy environment by changing the beam mode to My Beam, which outputs sound

beams directly toward the listening position in a single channel. In addition, My Beam is also ideal when you do not want

the sound beams to be reflected on the walls in your listening room or when you do not want to disturb other people

while enjoying music or movies at night.

If My Beam is selected as the beam mode, the surround modes (see page 58), the CINEMA DSP programs (see page 65), and TruBass

(see page 81) become ineffective. In addition, no audio is output from the subwoofer connected to this unit.

The My Beam microphone on the remote control collects

the test tones from this unit so that the beam angle can be

automatically adjusted.

1 Set the operation mode selector to YSP.

2 Press and hold MY BEAM for more than two

seconds.

A test tone is output twice from this unit. Keep

pointing the remote control toward this unit while the

test tones are being output so that the My Beam

microphone can collect the test tones.

Control range: L60° to R60°

Operation guarantee range: 6 m (20 ft), L45° to R45°

• If an error occurs, an error buzzer is played and “MY BEAM

ERROR” is displayed in the front panel display.

• An error may occur if the listening room is noisy. Make sure

that the listening room is as quiet as possible while the test

tones are being output.

• Do not shake or move the remote control while the test tones are

being output.

• Do not cover the My Beam microphone on the remote control

while the test tones are being output.

• The batteries in the remote control may be weak if the remote

control does not function properly. In this case, replace all the

batteries and then try the procedure again.

• When the input signal with 64 kHz, 88.2 kHz or 96 kHz of

sampling frequency is being played back, the beam angle

cannot be automatically adjusted.

Playing back sound clearly (My Beam)

Note

STEREO

MY BEAM MY SUR.

ENHANCER MENU

RETURNDISPLAY

ENTER

SUR. DECODEOFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

ENTRY

CAT/

A-E

321

+10

789

YSP

TV/AV

POWERPOWERSTANDBY/ON

My Beam

microphone

Using auto-adjust function

YSP

TV/AV

MY BEAM

Notes

64 En

Playing back sound clearly (My Beam)

You can adjust the beam angle manually while playing

back an input source. This function is also ideal if the

listening position is out of the operation guarantee range

of the auto-adjust function.

1 Set the operation mode selector to YSP.

2 Press MY BEAM.

“MY BEAM” is displayed in the front panel display.

3 Press / while “MY BEAM” is displayed to

adjust the beam angle.

Control range: L90° to R90°

• Press repeatedly to increase the horizontal angle

on the left side.

• Press repeatedly to increase the horizontal angle

on the right side.

Using manual-adjust function

YSP

TV/AV

MY BEAM

ENTER

ANGLE 0

USING SOUND FIELD PROGRAMS

65 En

BASIC

OPERATION

English

This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from

stereo or multi-channel sources. This unit is also equipped with a Yamaha CINEMA DSP (digital sound field processing)

chip containing several sound field programs used to enhance your playback experience. Most of the CINEMA DSP

programs are precise digital recreations of actual acoustic environments found in famous concert halls, music venues, and

movie theaters.

The Yamaha CINEMA DSP programs are compatible with all Dolby Digital, DTS, and Dolby Surround sources.

Choose a CINEMA DSP program based on your listening preference and do not purely rely on the name of the CINEMA DSP program

itself.

■ What is a sound field?

A significant factor that creates the rich, full tones of a live instrument is the multiple reflections from the walls of the

room. In addition to making the sound live, these reflections enable the listener to tell where the player is situated as well

as the size and shape of the room in which the listener is sitting.

■ Elements of a sound field

In any environment, there are two distinct types of sound reflections combined with the direct sound coming straight to

our ears from the player’s instrument to make up the sound field.

Early reflections

Reflected sounds reach our ears extremely rapidly (50 ms to 80 ms after the direct sound) after reflecting from one

surface only (from the ceiling or the wall, for example). Early reflections help add clarity to the direct sound.

Reverberations

These are caused by reflections from more than one surface (i.e., wall, ceiling, the back of the room, etc.) so numerous

that they merge together to form a continuous sonic afterglow. They are non-directional and lessen the clarity of the direct

sound.

Direct sound, early reflections, and subsequent reverberations all together help us determine the subjective size and shape

of the room, and it is this information that the digital sound field processor reproduces in order to create the sound fields.

With the appropriate early reflections and subsequent reverberations in your listening room, you can create your own

listening environment. The acoustics in your room could be changed to those of a concert hall, a dance floor, or a

listening room of virtually any size at all. This ability to create sound fields at will is exactly what Yamaha has done with

the CINEMA DSP technology.

Using sound field programs

Note

66 En

Using sound field programs

You can select from three different CINEMA DSP

programs (MUSIC, MOVIE, and SPORTS) depending on

the type of source you want to enjoy. The CINEMA DSP

indicator lights up in the front panel display when one of

the CINEMA DSP programs is selected.

• The CINEMA DSP programs are ineffective when My

Surround (see page 57), stereo sound (see pages 62) and My

Beam (see pages 63) is selected as the beam mode.

• If the CINEMA DSP programs are not available, “Prohibit”

appears in the front panel display when you press one of the

CINEMA DSP program buttons on the remote control.

■ Music program

Select this CINEMA DSP program when you play back

music sources. This program produces a vibrant

atmosphere and lets you feel as if you are seated in an

actual rock or jazz concert hall.

1 Set the operation mode selector to YSP.

2 Press MUSIC to select the music CINEMA

DSP program.

■ Movie program

Select this CINEMA DSP program when you play back

movie sources, especially the ones encoded in Dolby

Digital, DTS, or Dolby Surround. This program clearly

reproduces dialog and sound effects, thus creating a broad

and expansive cinematic space amid silence.

1 Set the operation mode selector to YSP.

2 Press MOVIE to select the movie CINEMA

DSP program.

■ Sports program

Select this CINEMA DSP program when you play back

sports sources. This program densely concentrates the

vocal sound of the commentator in the center while

broadening the sound from the audience or the

environment all around your listening room.

1 Set the operation mode selector to YSP.

2 Press SPORTS to select the sports CINEMA

DSP program.

CINEMA DSP programs

Notes

STEREO

MY BEAM MY SUR.

ENHANCER MENU

RETURNDISPLAY

ENTER

SUR. DECODEOFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

ENTRY

CAT/

A-E

321

+10

789

YSP

TV/AV

YSP

TV/AV

MUSIC

YSP

TV/AV

MOVIE

YSP

TV/AV

SPORTS

67 En

Using sound field programs

BASIC

OPERATION

English

■ Turning off CINEMA DSP programs

Turn off the CINEMA DSP programs if you want to enjoy

the original sound without the CINEMA DSP program

effect.

1 Set the operation mode selector to YSP.

2 Press OFF to turn off the CINEMA DSP

programs.

“CINEMA DSP OFF” is displayed in the front panel

display and the CINEMA DSP indicator disappears.

■ Adjusting CINEMA DSP effect levels

You can enjoy good quality sound with the factory preset

parameters. However, you can also adjust the effect level

of the CINEMA DSP programs relative to the level of the

direct sound so that each CINEMA DSP program can

reflect your listening environment and your preference

even more accurately.

1 Set the operation mode selector to YSP.

2 Press MUSIC, MOVIE, or SPORTS to select

the desired CINEMA DSP program.

3 Press / .

“DSP LEVEL” is displayed in the front panel display.

4 Press / to adjust the effect level of the

selected CINEMA DSP program.

Control range: –6 dB to +3 dB

• A larger value increases the effect level.

• A smaller value decreases the effect level.

YSP

TV/AV

OFF

CINEMA DSP OFF

YSP

TV/AV

SPORTS

MOVIE

MUSIC

or or

DSP LEVEL 0dB

ENTER

ENTRY

ENTER

USING THE MUSIC ENHANCER

68 En

You can use the Music Enhancer of this unit to improve the sound nearest to the original depth and width of compression

artifacts such as the MP3 format.

1 Set the operation mode selector to YSP.

2 Press ENHANCER to select the Music

Enhancer.

The currently selected mode appears in the front

panel display.

3 Press ENHANCER repeatedly to switch

between the Music Enhancer levels (OFF,

HIGH, and LOW).

The ENHANCER indicator lights up when

“ENHANCER:HIGH” or “ENHANCER:LOW” is

selected.

• The Music Enhancer is not compatible with the CINEMA DSP

programs. If a CINEMA DSP program is selected while the

Music Enhancer is on, the Music Enhancer is turned off

automatically. In this case, the Music Enhancer remains off

even after the CINEMA DSP program is canceled. Likewise, if

the Music Enhancer is turned on while a CINEMA DSP

program is selected, the CINEMA DSP program is canceled

automatically. In this case, the CINEMA DSP program remains

off even after the Music Enhancer is turned off.

• The Music Enhancer is available only when a setting other than

My Surround (see page 57) is selected as the beam mode.

Using the music enhancer

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

ENTER

SUR. DECODEOFF

SPORTSMUSIC MOVIE

ENTRY

CAT/

A-E

+10

789

YSP

TV/AV

YSP

TV/AV

ENHANCER

Notes

ENHANCER:HIGH

ENHANCER:LOW

ENHANCER:OFF

ENHANCER

Lights up

USING THE VOLUME MODE (NIGHT LISTENING ENHANCER/TV VOLUME EQUAL MODE)

69 En

BASIC

OPERATION

English

The night listening enhancers are designed to improve listenability at lower volumes or at night. In addition, you can limit

the volume level of the TV so that it will not vary suddenly to a great extent whenever the contents being broadcast

change (i.e. due to commercials, etc.).

1 Set the operation mode selector to YSP.

2 Press VOL MODE repeatedly to select

NIGHT:CINEMA, NIGHT:MUSIC, TV EQUAL

VOLUME, or OFF.

The NIGHT indicator lights up in the front panel

display when “NIGHT:CINEMA” or

“NIGHT:MUSIC” is selected.

The EQUAL indicator lights up in the front panel

display when “TV EQUAL VOLUME” is selected.

• Select NIGHT:CINEMA when watching films to

reduce the dynamic range of film soundtracks and

to make dialog easier to hear at lower volumes.

• Select NIGHT:MUSIC when listening to music

sources to preserve ease-of-listening for all sounds.

• Select TV EQUAL VOLUME when watching TV

programs.

• Select OFF to turn off the volume mode.

3 Press / to adjust the effect level of

compression while NIGHT:CINEMA,

NIGHT:MUSIC, or TV EQUAL VOLUME is

displayed.

• Select Effect.Lvl:MIN for minimum compression.

• Select Effect.Lvl:MID for standard compression.

• Select Effect.Lvl:MAX for maximum

compression.

• The volume mode settings are canceled if you press

STANDBY/ON or disconnect the AC power supply cable from

the AC wall outlet.

• The volume mode settings become ineffective when My

Surround is selected as the beam mode (see page 57).

Using the volume mode

(Night listening enhancer/TV volume equal mode)

STEREO

MY BEAM MY SUR.

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

ENTER

SUR. DECODEOFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

ENTRY

CAT/

A-E

321

+10

789

YSP

TV/AV

YSP

TV/AV

NIGHT:CINEMA

NIGHT:MUSIC

TV EQUAL VOLUME

OFF

VOL MODE

Lights up

Notes

Lights up

Effect.Lvl:MIN

Effect.Lvl:MID

Effect.Lvl:MAX

ENTER

USING THE SLEEP TIMER

70 En

Use this feature to automatically set this unit to the standby mode after a specified period of time. The sleep timer is

useful if you are going to sleep after a certain amount of time while this unit is still playing back a source.

1 Set the operation mode selector to YSP.

2 Press SLEEP repeatedly to set the interval

for the sleep timer.

Choices: 120min, 90min, 60min, 30min, OFF

The SLEEP indicator flashes in the front panel

display while switching the interval for the sleep

timer.

Each time you press SLEEP, the front panel display

changes as shown below.

3 Wait for a few seconds without operating this

unit to confirm the setting for the sleep timer.

The SLEEP indicator lights up in the front panel

display, indicating that the sleep timer is activated.

Using the sleep timer

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

ENTER

SUR. DECODEOFF

SPORTS

MY SUR.

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

ENTRY

CAT/

A-E

321

+10

789

YSP

TV/AV

YSP

TV/AV

SLEEP

Flashes

SLEEP

SLEEP 120min

SLEEP 90min

SLEEP 60min

SLEEP 30min

SLEEP OFF

Lights up

71 En

Using the sleep timer

BASIC

OPERATION

English

■ Canceling the sleep timer

1 Set the operation mode selector to YSP.

2 Press SLEEP repeatedly until “SLEEP OFF”

appears in the front panel display.

3 Wait for a few seconds without operating this

unit to confirm the setting for the sleep timer.

The SLEEP indicator disappears from the front panel

display, indicating that the sleep timer is deactivated.

• The sleep timer setting can also be deactivated if you press

STANDBY/ON to set this unit to the standby mode or unplug

the AC power supply cable from the AC outlet.

• When you cancel the sleep timer by pressing STANDBY/ON,

the previous setting for the sleep timer is stored in the system

memory.

YSP

TV/AV

SLEEP

SLEEP OFF

Disappears

DISPLAYING THE INPUT SOURCE INFORMATION

72 En

You can display the format and sampling frequency of the current input signal in the front panel display.

1 Set the operation mode selector to YSP.

2 Press DISPLAY.

The information on the current input signal is

displayed as follows:

When the input signal is unclear, “– – –” is displayed for the

sampling frequency.

Displaying the input source information

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

TV INPUT TV MUTE

ENTER

SUR. DECODEOFF

ENTRY

CAT/

A-E

+10

YSP

TV/AV

YSP

TV/AV

Input signal Displayed

Sampling

frequency

Dolby digital DOLBY DGTL

32/44.1/48/64/

88.2/96 kHz

DTS DTS

PCM PCM

Analog ANALOG –

DISPLAY

INPUT SIGNAL

DOLBY DGTL:48kHz

D.DGTL:48kHz

USING THE HDMI CONTROL FEATURE

73 En

BASIC

OPERATION

English

You can operate the following functions using the remote control supplied with your TV if this unit and an HDMI

control-compatible TV (except some models) are connected via HDMI.

• Turning on or off the power (synchronized operation with the TV)

• Selecting the audio output component (TV or this unit)

• Adjusting the volume level (up/down and mute)

Examples of the HDMI control-compatible component are Panasonic VIERA Link compatible component (TV, DVD

recorder, Blu-ray Disc player) where VIERA Link is a new name of EZ Sync in North America and Toshiba REGZA-

LINK (its previous name is “CE Link” in North America) compatible TZs.

Not all 2008 Panasonic VIERA Link features are compatible with 2006/2007 EZ Sync products.

If you connect this unit to an HDMI control-compatible DVD player or Blu-ray Disc player via HDMI, you can also control the

connected component in synchronization with this unit (except some models).

1 Connect this unit to your HDMI control-compatible TV via HDMI.

For details about HDMI and HDMI components, see “Information on HDMI™” on page 17 and “Case 1:

Connections using HDMI cables” on page 18. Also in the owner’s manual supplied with your TV, refer to the

information on connecting an AV amplifier.

2 Turn on the power of all components connected via HDMI.

For details about controlling external components, see the owner’s manuals supplied with your components.

3 Set HDMI control to ON. For details, refer to page 85.

4 Change the HDMI1 input at “Input assignment” to something other than “TV/STB” (for example to

“AUX1”). (See page 82.)

5 Check the system settings for all components connected via HDMI and activate the HDMI control

feature.

For details about setting external components, see the owner’s manuals supplied with your components. Once you

have followed steps 1 to 5, you do not need to carry out the same procedure again next time.

6 Turn off the power of your TV and then turn on the power again.

7 Set the input source selector of your TV to this unit (HDMI, etc.).

8 Select the connected component as the input source by pressing INPUT on the front panel of this

unit (or press one of the input selector buttons on the remote control). Confirm that the video

image played back on the DVD recorder (etc.) appears in your TV correctly.

9 Use the remote control supplied with your TV to turn on or off the power, select the audio output

component, and adjust the volume level of this unit.

• Check whether the HDMI control feature is activated for your TV (see the owner’s manual supplied with your TV) if you cannot

operate this unit in synchronization with your TV.

• While you are playing back audio from a non-HDMI component, turning off the power of your TV with the remote control supplied

with your TV does not turn off the power of this unit. Playback continues without being affected.

Using the HDMI control feature

Note

Notes

MANUAL SETUP

74 En

To achieve the best quality surround sound, you can use MANUAL SETUP to fine-tune the listening environment

parameters, as well as to make advanced settings for sound signals, sound beams, digital input, and the OSD. Change the

initial settings (indicated in bold under each parameter) to reflect the needs of your own listening environment.

• You can save the settings optimized by the AUTO SETUP procedure (see page 36). A set of settings optimized according to the

specific conditions of your listening environment can be recalled later depending on the varying conditions of your listening

environment (see page 37).

• Most of the parameters in SOUND MENU and BEAM MENU are automatically set when you run AUTO SETUP (see page 29). Use

SOUND MENU and BEAM MENU to make additional adjustments.

• BEAM MENU allows you to make settings for the surround sound effects normally available in the speaker settings menu.

• Make settings for the parameters in BEAM MENU first before making settings for the parameters in SOUND MENU, INPUT MENU,

and DISPLAY MENU.

SOUND MENU

Use to manually adjust the various parameters related to the sound output.

BEAM MENU

Use to manually adjust the various parameters related to the sound beam output.

INPUT MENU

Use to manually adjust the various parameters related to the audio and video input.

DISPLAY MENU

Use to manually adjust the various parameters related to the display.

MANUAL SETUP

Item Features Page

TONE CONTROL Adjusts the output level of high-frequency or low-frequency sound.

SUBWOOFER SET Adjusts the various subwoofer settings.

MUTE LEVEL Adjusts the muting level.

AUDIO DELAY Adjusts the audio delay.

ROOM EQ Adjusts the tonal quality of the listening room.

DD/DTS Dynamic Range Adjusts the dynamic range of Dolby Digital or DTS signals.

TruBass Selects the bass sound enhancer.

Item Features Page

SETTING PARAMETERS Adjusts the listening room and listening position settings.

BEAM ADJUSTMENT Adjusts the various sound beam settings.

IMAGE LOCATION Adjusts the sound position of the front left and right channels.

Item Features Page

INPUT ASSIGNMENT Assigns jacks according to the component to be used.

INPUT MODE Selects the initial input of the source.

INPUT TRIM Adjusts the input level of the source.

INPUT RENAME Renames the displayed input source.

HDMI SET Adjusts the various HDMI settings.

XM ANTENNA LEVEL Displays the current reception level of the XM Satellite Radio signal.

Item Features Page

F.DISPLAY SET Adjusts the front panel display settings.

OSD SET Adjusts the OSD settings.

UNIT SET Changes the display unit of measurement.

75 En

MANUAL SETUP

ADVANCED

OPERATION

English

Use the remote control to access and adjust each

parameter.

You can adjust the SET MENU parameters while the unit is

reproducing sound.

1 Set the operation mode selector to YSP.

2 Press MENU.

The SET MENU screen appears on your TV.

• The control buttons used for SET MENU are displayed at

the bottom of the screen.

• To return to the previous screen while using SET MENU,

press RETURN.

• To exit from the SET MENU screen, press MENU once

more.

• You can also perform the following operations in the front

panel display.

3 Press / to select MANUAL SETUP and

press ENTER.

The following screen appears on your TV.

4 Press / to select a sub menu and press

ENTER.

5 Press / / / and ENTER to configure

each parameter.

6 Press MENU to exit.

The OSD disappears from your TV screen.

Using MANUAL SETUP

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

ENTER

SUR. DECODEOFF

SPORTSMUSIC MOVIE

ENTRY

CAT/

A-E

+10

789

YSP

TV/AV

YSP

TV/AV

;MEMORY

;AUTO SETUP

;MANUAL SETUP

;LANGUAGE SETUP

[ ]/[ ]:Up/Down

[ENTER]:Enter

SET MENU

ENTER

1)SOUND MENU

2)BEAM MENU

3)INPUT MENU

4)DISPLAY MENU

[ ]/[ ]:Up/Down

[ENTER]:Enter

;MANUAL SETUP

ENTER

76 En

MANUAL SETUP

Use to manually adjust the various parameters related to

the sound beam output.

SET MENU → MANUAL SETUP → BEAM MENU

You can adjust the sound beam output level of each channel in

“Adjusting the audio balance” (see page 87).

■ SETTING PARAMETERS

(Setting parameters)

Use to set the position of this unit in your listening room

and the distance of this unit from the listening position.

When you make settings for each parameter, other related

parameters are automatically adjusted to best match your

listening environment.

If you make adjustments in SETTING PARAMETERS, the beam

optimization settings made in the AUTO SETUP procedure will

be lost. If you want to keep the beam optimization settings made

in the AUTO SETUP and make further adjustments, adjust

settings in BEAM ADJUSTMENT first (see page 77).

INSTALLED POSITION

(Installed position of this unit)

Use to adjust the installed position of this unit.

Choices: FLAT TO WALL (Parallel to wall installation),

ANGLE TO WALL OR CORNER

(Corner installation)

• Select FLAT TO WALL if this unit is installed in

parallel with the wall in your listening room. Adjust the

width and length of your listening room as well as the

distance of the listening position from this unit and the

distance of the center of this unit from the left wall.

Choices for the room width and length:

2.0 m to 12.0 m (6.5 ft to 40.0 ft)

Choices for the listening position from this unit:

1.8 m to 9.0 m (6.0 ft to 30.0 ft)

Choices for the listening position from the left wall:

0.6 m to 11.4 m (2.0 ft to 38.0 ft)

BEAM MENU

Note

A)SETTING PARAMETERS

B)BEAM ADJUSTMENT

C)IMAGE LOCATION

[ ]/[ ]:Up/Down

[ENTER]:Enter

2)BEAM MENU

INSTALLED POSITION

;;;;;;;FLAT TO WALL

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

A)SETTING PARAMETERS 1/3

FLAT TO WALL

ANGLE TO WALL

OR CORNER

Listening position

from the left wall

Listening position

from the unit

Room width

Room length

A)SETTING PARAMETERS 2/3

-------[ 5.4m ]-

4.9m

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

--------|

2.7m [ 2.5m ]

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

A)SETTING PARAMETERS 3/3

Room width and

length

Listening position

from the unit and

the left wall

77 En

MANUAL SETUP

ADVANCED

OPERATION

English

• Select ANGLE TO WALL OR CORNER if this unit is

installed in the corner of your listening room. Adjust

the width and length of your listening room as well as

the distance of the listening position from this unit.

Choices for the room width and length:

2.0 m to 12.0 m (6.5 ft to 40.0 ft)

Choices for the listening position from this unit:

1.8 m to 9.0 m (6.0 ft to 30.0 ft)

When you set the INSTALLED POSITION parameter in

MANUAL SETUP (see page 76), the parameters newly set for

the width and length of your listening room are automatically set

as the factory default value.

■ BEAM ADJUSTMENT (Beam adjustment)

Use to manually adjust the various sound beam settings.

We recommend that you select 5 Beam as the beam mode

before adjusting these parameters (see page 56).

• When INSTALLED POSITION is adjusted in MANUAL

SETUP (see page 76), the factory default value is automatically

set for this parameter except Center in FOCAL LENGTH (see

page 78).

• Depending on the beam mode settings (see pages 56, 57, 62 and

63), some channel positions may not be available for selection.

In this case, “– –” is displayed. When using Stereo plus 3 Beam

as the beam mode, set the surround left and right signals to be

output from the front left and right channels.

HORIZONTAL ANGLE (Horizontal angle)

Use to adjust the horizontal angle of sound beams for each

channel. By adjusting the horizontal angle of the sound

beams, you can optimize the sound beam paths. A test

tone is automatically output.

Choices: L90° to R90°

Adjust toward L (left) to move the direction of the output

to the left and adjust toward R (right) to move it to the

right.

Note

Listening position

from the unit

Room length

Room width

----- 5.4m ---

[ 5.4m ]

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

A)SETTING PARAMETERS 2/3

[ 2.5m ]

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

A)SETTING PARAMETERS 3/3

Room width and

length

Listening

position from the

unit

Notes

a)HORIZONTAL ANGLE

b)BEAM TRAVEL LENGTH

c)FOCAL LENGTH

d)TREBLE GAIN

[ ]/[ ]:Up/Down

[ENTER]:Enter

B)BEAM ADJUSTMENT

( )

(+)

( )

5 beam

Front L L90 R90

L65deg

0(deg)

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

a)HORIZONTAL ANGLE 1/5

78 En

MANUAL SETUP

BEAM TRAVEL LENGTH (Beam travel length)

A certain amount of delay must be applied to the sound

from each channel so that all sounds can arrive at the

listening position at the same time. This menu sets the

distance that sound beams travel after being output and

reflected off the wall until they arrive at the listening

position and adjusts the delay applied to the respective

channel.

The lines in the illustration below indicate the distance.

Choices: 0.3 m to 24.0 m (1.0 ft to 80.0 ft)

• Front L adjusts the distance the front left channel

sound beams travel.

• Front R adjusts the distance the front right channel

sound beams travel.

• Center adjusts the distance the center channel sound

beams travel.

• Surround L adjusts the distance the surround left

channel sound beams travel.

• Surround R adjusts the distance the surround right

channel sound beams travel.

We recommend that you use the setting optimized by AUTO

SETUP (see page 29). Adjust this parameter only when you

changed HORIZONTAL ANGLE (see page 77).

FOCAL LENGTH (Focal length)

Use to set the distance from the front of this unit to the

focal point of output for each channel to achieve an

expansive feeling for each channel.

The focal points except for the center channel should be

set near the reflection points on the walls. The shorter the

distance, the larger the expansion.

Choices: –1.0 m to +13.0 m (–3.5 ft to +43.5 ft)

Adjust toward – (minus) to move the focus outward and

adjust toward + (plus) to move the focus toward the

normal position.

• Front L adjusts the focal length for the front left sound

beams.

• Front R adjusts the focal length for the front right

sound beams.

• Center adjusts the focal length for the center sound

beams. Initial setting: –0.5 m (–1.5 ft)

• Surround L adjusts the focal length for the surround

left sound beams.

• Surround R adjusts the focal length for the surround

right sound beams.

We recommend that you use the initial setting (–0.5 m (or 1.5 ft))

for the center channel.

5 beam

Front L;;;;;;;6.0m

Front R;;;;;;;6.0m

Center;;;;;;;;2.5m

Surround L;;;;9.1m

Surround R;;;;9.1m

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

b)BEAM TRAVEL LENGTH

focal length

focal point

sweet spot

Front left channel Center channel

5 beam

Front L;;;;;;+1.5m

Front R;;;;;;+1.5m

Center;;;;;;;-0.5m

Surround L;;;+2.3m

Surround R;;;+2.3m

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

c)FOCAL LENGTH

79 En

MANUAL SETUP

ADVANCED

OPERATION

English

TREBLE GAIN (Treble gain)

Use to adjust the high-frequency output level of each

channel.

If the reflection points of the front left and right or surround left

and right sound beams are on curtain or other acoustically

absorbent surfaces, you can achieve more effective surround

sound by increasing the treble level for those sound beams.

Choices: –12.0 dB to +12.0 dB

Initial setting: 0 dB

• Front L adjusts the high-frequency output level of the

front left channel.

• Front R adjusts the high-frequency output level of the

front right channel.

• Center adjusts the high-frequency output level of the

center channel.

• Surround L adjusts the high-frequency output level

of the surround left channel.

• Surround R adjusts the high-frequency output level

of the surround right channel.

■ IMAGE LOCATION (Image location)

Use to adjust the direction from which the front left and

right channel sound is heard so that each sound can be

heard closer to the center channel.

Use this feature to redirect audio signals if the sound

coming from the front left and right channels seems

unnatural, such as when your listening position is not the

center of your listening room.

You can only adjust this parameter when 3 Beam or 5

Beam is selected as the beam mode (see pages 56 and 57).

Choices: ON, OFF

Setting range: 0% to 95%

Initial setting: 0%

LEFT (Left)

Adjusts audio signals toward the left.

The higher the percentage, the louder the output from the

center.

RIGHT (Right)

Adjusts audio signals toward the right.

The higher the percentage, the louder the output from the

center.

- +

Front L;;;;;;;;0dB

Front R;;;;;;;;0dB

Center;;;;;;;;;0dB

Surround L;;;;;0dB

Surround R;;;;;0dB

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

d)TREBLE GAIN

------

OFF )ON

LCR

LEFT;;;;;;;;;;;0%

RIGHT;;;;;;;;;;0%

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

C)IMAGE LOCATION

Without adjustment

With the front left

channel adjusted

Without adjustment

With the front right

channel adjusted

80 En

MANUAL SETUP

Use to manually adjust the various parameters related to

the sound output.

SET MENU → MANUAL SETUP → SOUND MENU

■ TONE CONTROL (Tone control)

You can adjust the tonal quality of sound beams.

TREBLE (Treble)

Use to adjust the high-frequency response.

Choices: –12 dB to +12 dB

Initial setting: 0 dB

BASS (Bass)

Use to adjust the low-frequency response.

Choices: –12 dB to +12 dB

Initial setting: 0 dB

■ SUBWOOFER SET (Subwoofer settings)

Use to manually adjust the various subwoofer

settings.

BASS OUT (Bass out)

Low-frequency (bass) signals can be directed to the

subwoofer or the front left and right channels. This setting

also determines the routing of LFE (low-frequency effect)

signals found in Dolby Digital or DTS sources.

Choices: SUBWOOFER (Subwoofer), FRONT

• Select SUBWOOFER if you connect a subwoofer. LFE

and low-frequency signals from other channels are

directed to the subwoofer.

• Select FRONT if you do not use a subwoofer. LFE and

low-frequency signals from other channels are directed

to the front left and right channels.

CROSS OVER (Crossover)

When BASS OUT is set to SUBWOOFER, you can use

this feature to select a crossover (cutoff) frequency for all

low-frequency signals. All frequencies below the selected

frequency will be sent to the subwoofer position.

Choices: 80Hz, 100Hz, 120Hz

LFE LEVEL (Low-frequency effect level)

Select to adjust the output level of the LFE (low-frequency

effect) channel according to the capacity of your

subwoofer. The LFE channel carries low-frequency

special effects which are only added to certain scenes.

This setting is effective only when this unit decodes Dolby

Digital or DTS signals.

Choices: –20 to 0 dB

DISTANCE (Distance)

Select to adjust the distance of the subwoofer from the

listening position.

Choices: 0.3 to 15.0 m (1.0 ft to 50.0 ft)

Initial setting: 3.0 m (10.0 ft)

■ MUTE LEVEL (Muting level)

Use to adjust how much the mute function reduces the

volume level.

Choices: MUTE, –20 dB

• Select MUTE to completely halt all sound output.

• Select –20 dB to reduce the current volume level by

20 dB.

SOUND MENU

A)TONE CONTROL

B)SUBWOOFER SET

C)MUTE LEVEL

D)AUDIO DELAY

E)ROOM EQ

F)DD/DTS Dynamic Range

G)TruBass

[ ]/[ ]:Up/Down

[ENTER]:Enter

1)SOUND MENU

TREBLE;;;;;0dB

BASS;;;;;;;0dB

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

A)TONE CONTROL

------

BASS OUT;;;;;FRONT

CROSS OVER;;;100Hz

LFE LEVEL;;;;;;0dB

DISTANCE;;;;;;3.0m

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

B)SUBWOOFER SET

MUTE -20dB

[ ]/[ ]:Select

[ENTER]:Return

C)MUTE LEVEL

81 En

MANUAL SETUP

ADVANCED

OPERATION

English

■ AUDIO DELAY (Audio delay)

Use to delay the sound output and synchronize it with the

video image. This may be necessary when using certain

LCD monitors or projectors.

Choices: 0 to 160 msec

■ ROOM EQ (Room equalizer)

Use to change the tonal qualities of your listening room

when the unit is mounted on the wall.

Choices: MOUNTING (Mount type),

REFLECTING (Reflectivity type)

MOUNTING (Mounting type)

Use to enhance medium to low range sounds.

Choices: WALL (Wall mount), SHELF (Shelf mount)

• Select WALL if this unit is mounted on the wall in your

listening room.

• Select SHELF if this unit is mounted on the shelf in

your listening room.

REFLECTING (Reflectivity type)

Use to select the reflectivity of your listening room.

Choices: NORMAL (Normal), HI ECHO (High echo)

• Select NORMAL if your listening room has a normal

reflectivity.

• Select HI ECHO if your listening room has highly

reflective surfaces such as concrete walls.

■ DD/DTS Dynamic Range

(Dynamic range of Dolby Digital and

DTS signals)

Use to select the amount of dynamic range compression.

This setting is effective only when the unit is decoding

Dolby Digital and DTS signals. Dynamic range is the

difference between the smallest sound that can be heard

above the noise of the equipment and the biggest sound

that can be heard without distortion.

Choices: MIN (minimum), STD (standard),

MAX (maximum)

Select to adjust the dynamic range compression.

• Select MIN for listening to sources at low volume

levels.

• Select STD for general use.

• Select MAX for feature films.

■ TruBass

Use to turn on or off the bass sound enhancer. The SRS

TruBass technology improves bass even without a

subwoofer and provides deeper, richer bass in the presence

of a subwoofer.

Choices: OFF, ON

TruBass is not available when My Beam (see page 63) or My

Surround (see page 57) is selected as the beam mode.

AUDIO DELAY;;;;;0msec

[ ]/[ ]:Select

[ENTER]:Return

D)AUDIO DELAY

MOUNTING;;;;;SHELF

REFLECTING;;;NORMAL

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

)ROOM EQ

Note

MIN STD MAX

[ ]/[ ]:Select

[ENTER]:Return

F)DD/DTS Dynamic Range

OFF ON

[ ]/[ ]:Select

[ENTER]:Return

G)TruBass

82 En

MANUAL SETUP

Use to manually adjust the various parameters related to

the audio and video input.

SET MENU → MANUAL SETUP → INPUT MENU

■ INPUT ASSIGNMENT (Input assignment)

Use to assign the HDMI IN jacks of this unit to other

components if the initial settings of this unit do not

correspond to your needs. By assigning other components

to the HDMI IN jacks of this unit, you can display the

names of the connected components in the front panel

display and OSD and operate the components with the

input selector buttons of the same name. If you connect a

component to one of the HDMI IN jacks of this unit and

do not assign a name to it, the default component name for

HDMI IN jack is displayed in the front panel and OSD

when selected.

• Select HDMI1 to assign a component to the HDMI

AUX 1 IN jack of this unit.

Choices: TV/STB, DVD, AUX1, AUX2

• Select HDMI2 to assign a component to the HDMI

DVD IN jack of this unit.

Choices: DVD, AUX1, AUX2, TV/STB

•

• Select COMPONENT to assign a component to the

COMPONENT VIDEO INPUT jack of this unit.

Choices: DVD, AUX1, AUX2, TV/STB

•

• Select COMPOSITE to assign a component to the

VIDEO INPUT jack of this unit.

Choices: TV/STB, DVD, AUX1, AUX2

■ INPUT MODE (Input mode)

Use to designate the input mode for the input sources

connected to the DIGITAL INPUT jacks when you turn on

the power of this unit. For information on the types of

audio signals that can be output by this unit, see “Selecting

the input mode” on page 90.

Choices: AUTO, LAST

• Select AUTO to set this unit to automatically detect the

type of input signals and select the appropriate input

mode.

• Select LAST to set this unit to automatically select the

last input mode used for that input source. If the type of

input signals is different from the setting, no sounds

will be produced.

INPUT MENU

A)INPUT ASSIGNMENT

B)INPUT MODE

C)INPUT TRIM

D)INPUT RENAME

E)HDMI SET

F)XM ANTENNA LEVEL

[ ]/[ ]:Up/Down

[ENTER]:Enter

3)INPUT MENU

HDMI

HDMI1;;;; TV/STB

( TV/STB )

HDMI2;;;; DVD

( DVD )

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

A)INPUT ASSIGNMENT 1/3

COMPONENT

Line1;;;; DVD

( DVD )

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

A)INPUT ASSIGNMENT 2/3

COMPOSITE

Line2;;;; TV/STB

( TV/STB )

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

A)INPUT ASSIGNMENT 3/3

AUTO LAST

[ ]/[ ]:Select

[ENTER]:Return

B)INPUT MODE

83 En

MANUAL SETUP

ADVANCED

OPERATION

English

■ INPUT TRIM (Input trim)

Use to adjust the input level of the input source.

• Select TV/STB ANALOG to adjust the level of audio

and video signals input at the TV/STB AUDIO INPUT

jacks of this unit.

Control range: –6.0 dB to 0.0 dB

Initial setting: –3.0 dB

• Select TV/STB DIGITAL to adjust the level of audio

and video signals input at the TV/STB OPTICAL

DIGITAL INPUT jack of this unit.

Control range: –6.0 dB to 0.0 dB

Initial setting: –3.0 dB

• Select DVD DIGITAL to adjust the level of audio and

video signals input at the DVD COAXIAL DIGITAL

INPUT jack of this unit.

Control range: –6.0 dB to 0.0 dB

Initial setting: –3.0 dB

• Select AUX1 ANALOG to adjust the level of audio and

video signals input at the AUX1 AUDIO INPUT jacks

of this unit.

Control range: –6.0 dB to 0.0 dB

Initial setting: –3.0 dB

• Select AUX1 DIGITAL to adjust the level of audio and

video signals input at the AUX 1 OPTICAL DIGITAL

INPUT jack of this unit.

Control range: –6.0 dB to 0.0 dB

Initial setting: –3.0 dB

• Select AUX2 DIGITAL to adjust the level of audio and

video signals input at the AUX 2 COAXIAL DIGITAL

INPUT jack of this unit.

Control range: –6.0 dB to 0.0 dB

Initial setting: –3.0 dB

• Select AUX3 ANALOG to adjust the level of audio

signals input at the AUX 3 input jack on the front panel.

Control range: –6.0 dB to 0.0 dB

Initial setting: –3.0 dB

• Select DOCK ANALOG to adjust the level of audio

signals input at the DOCK terminal of this unit.

Control range: –6.0 dB to 0.0 dB

Initial setting: –3.0 dB

■ INPUT RENAME (Input rename)

Use to change the name of the input source in the OSD

and the front panel display. Press an input selector button

(e.g., DVD) to select the component you want to change

the name for and perform the following procedure.

1 Press / to place the _ (underscore) under

the space or the character you want to edit.

The _ (underscore) flashes.

2 Press / to select the desired character.

• You can use up to 8 characters for each input.

• Press to change the character in the following

order or press to go in the reverse order:

A to Z, a space, 0 to 9, a space, a to z, a space, #, *,

+, etc.

3 Repeat steps 1 to 2 to rename each input.

4 Press ENTER to exit.

The new names are registered, and the display returns

to the previous screen.

TV/STB ANALOG;;;-3.0dB

DIGITAL;;-3.0dB

DVD DIGITAL;;-3.0dB

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

C)INPUT TRIM 1/2

AUX1 ANALOG;;;-3.0dB

DIGITAL;;-3.0dB

AUX2 DIGITAL;;-3.0dB

AUX3 ANALOG;;;-3.0dB

DOCK ANALOG;;;-3.0dB

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

C)INPUT TRIM 2/2

DVD -> DVD

[ ]/[ ]:Position

[ ]/[ ]:Character

[ENTER]:Return

D)INPUT RENAME

ENTER

84 En

MANUAL SETUP

■ HDMI SET (HDMI settings)

Use to change the HDMI audio/video output/input to

match the connected component.

Choices: SUPPORT AUDIO (Support audio),

AUDIO SELECT (Audio select),

VIDEO INFO (Video information),

UP-SCALING (HDMI up-scaling),

ASPECT RATIO (HDMI aspect ratio),

HDMI CONTROL (HDMI control)

SUPPORT AUDIO (Support audio)

Use to select whether to play back HDMI audio signals on

this unit or on another HDMI component connected to the

HDMI OUT jack of this unit.

Choices: YSP-3050, OTHER

• This setting is effective when HDMI CONTROL is set to OFF

(see page 85).

• The HDMI video signals input at one of the HDMI IN jacks of

this unit are always output at the HDMI OUT jack of this unit.

• When HDMI CONTROL is set to ON, this setting is ineffective.

This unit follows the setting of the HDMI control-compatible

TV.

AUDIO SELECT (Audio select)

Use to select whether to use the signals input at the HDMI

IN jack, with respect to the audio signals of the device

connected to the HDMI jack.

When only two channels of the multi-channel audio

signals input at the HDMI IN jack are output, connect this

unit and the player via an optical or coaxial digital

connection, as well as the HDMI connection, and set

AUDIO SELECT to OFF. The audio signals are output

from this unit in multi-channel via the connected optical

or coaxial digital jacks.

Choices: ON, OFF

• The video signal input at the HDMI jacks is output, regardless

of the AUDIO SELECT setting.

• The AUDIO SELECT setting is applied only to the sound

output from this unit. It is invalid when the sound is output from

the device connected to the HDMI OUT jacks.

VIDEO INFO (Video information)

Use to display the video information of the current input

signal.

Choices: HDMI SIGNAL, HDMI RES., HDMI ERROR

• Select HDMI SIGNAL to display the type of the

HDMI input/output signals.

• Select HDMI RES. to display the resolution of the

HDMI input/output signals.

• Select HDMI ERROR to display the error message for

HDMI sources or devices connected

(see page 102 for details).

UP-SCALING (HDMI up-scaling)

Use this feature to activate or deactivate the HDMI up-

conversion of the analog video signals input at the

composite video and component video jacks so that the

up-scaled analog video signals are output at the HDMI

OUT jack. This unit up-scales the analog video signals as

follows:

• 480i (NTSC)/576i (PAL) → 480p (NTSC)/576p (PAL),

1080i or 720p

• 480p (NTSC)/576p (PAL) → 1080i or 720p

Choices: OFF, THROUGH, 480p (or 576p), 1080i, 720p

Notes

E)HDMI SET

a)SUPPORT AUDIO

b)AUDIO SELECT

c)VIDEO INFO.

d)UP-SCALING

e)ASPECT RATIO

f)HDMI CONTROL

[ ]/[ ]:Up/Down

[ENTER]:Enter

YSP-3050 OTHER

[ ]/[ ]:Select

[ENTER]:Return

a)SUPPORT AUDIO

Note

HDMI1 TV/STB;;;;;;;;; ON

(TV/STB)

HDMI2 DVD;;;;;;;;;;; ON

( DVD )

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

b)AUDIO SELECT

HDMI SIGNAL;;;HDMI -> HDMI

HDMI RES.;;;;1080P -> 1080P

HDMI ERROR;;;----

[ ]/[ ]:Up/Down

[ENTER]:Return

c)VIDEO INFO.

HDMI UP-SCALING;;THROUGH

XXXXXXXXXXXXXXXXXXXXXXXXXXXXX

[ ]/[ ]:Select

[ENTER]:Return

d)UP-SCALING

85 En

MANUAL SETUP

ADVANCED

OPERATION

English

• Select OFF to deactivate the HDMI up-conversion

feature

• Select THROUGH not to up-scale any analog video

signals.

• Select 480p (or 576p), 1080i, or 720p to up-scale

analog video signals to 480p (or 576p), 1080i, or 720p

of resolution.

• When “MONITOR CHECK” is set to “YES”, this unit receives

the information of the available video signal resolutions from

the video monitor connected via HDMI and you can only select

the resolutions supported by the video monitor in “UP-

SCALING” (see page 84).

• When “MONITOR CHECK” is set to “SKIP”, an asterisk (*)

appears on the left of the unavailable video signal resolution(s)

(see page 92).

ASPECT RATIO (HDMI aspect ratio)

Use this feature to select the adjustment of aspect ratio for

analog video signals output at the HDMI OUT jack.

Choices: THROUGH, 16:9 Normal, Smart Zoom

• Select THROUGH if you do not make any adjustments

to the aspect ratio for HDMI video signal sources.

• Select 16:9 Normal to display video images with 4:3 of

aspect ratio on your video monitor with 16:9 of aspect ratio.

Black stripes appear on the right and left sides as a result.

• Select Smart Zoom to fit video images with 4:3 of aspect

ratio to your video monitor with 16:9 of aspect ratio.

• When “UP-SCALING” is set to “THROUGH”, you cannot

make any adjustments to “ASPECT RATIO”.

• When “ASPECT RATIO” is set to “Smart Zoom”, the video

images of the edge of the video monitor are rather stretched.

• When the video signals are input at the HDMI IN jacks or the

signals are input with 720p or 1080i of resolution, the

“ASPECT RATIO” setting does not affect the video signals

output at the HDMI OUT jack.

HDMI CONTROL (HDMI control)

Use this function to link this unit and an HDMI control-

compatible TV via HDMI. You can turn on or off the

power, select the input mode, and adjust the volume level

of this unit using the remote control supplied with your

HDMI control-compatible TV. For details, see “Using the

HDMI control feature” on page 73.

Choices: OFF, ON

• Select ON to enable the HDMI control.

• Select OFF to disable the HDMI control.

• When “HDMI CONTROL” is set to “ON”, the amount

of power consumption in the standby mode is increase.

• When HDMI CONTROL is set to OFF and this unit is in the

standby mode, the signals input at the HDMI IN jacks are not

output at the HDMI OUT jack.

• In order for the HDMI control function to work properly, we

recommend that the devices connected using the HDMI jacks

(TV, DVD recorder, Blu-ray recorder, etc.) be of the same make.

■ XM ANTENNA LEVEL (XM antenna level)

Use to display the current reception level of the XM

Satellite Radio signals. For the best reception, orient the

connected XM Mini-Tuner Dock to obtain a value of 60%

or more.

Display status: NONE, 0 to 100%

“NONE” is displayed if the XM Mini-Tuner Dock is not

connected to this unit. In this case, check the antenna connections

(see page 5 in the Reference Guide).

Notes

HDMI ASPECT RATIO;;;THROUGH

XXXXXXXXXXXXXXXXXXXXXXXXXXXXX

[ ]/[ ]:Select

[ENTER]:Return

e)ASPECT RATIO

Notes

Note

OFF ON XXXXXXX

XXXXXXXXXXXXXXXXXXXXXXXXXXXXX

[ ]/[ ]:Select

[ENTER]:Return

f)HDMI CONTROL

XM ANTENNA LEVEL;;;;97%

[ENTER]:Return

F)XM ANTENNA LEVEL

86 En

MANUAL SETUP

Use to manually adjust the various parameters related to

the display.

SET MENU → MANUAL SETUP → DISPLAY MENU

■ F.DISPLAY SET

(Front panel display settings)

Use to adjust the brightness and display settings of the

front panel display.

STANDARD DIMMER (Standard dimmer)

Use to adjust the brightness of the front panel display

when you operate this unit by using the control buttons on

the front panel or on the remote control.

Choices: –2, –1, OFF

AUTO DIMMER (Auto dimmer)

If no operation is performed for a specified period of time,

the front panel display dims. Use to adjust the brightness

of the front panel display in this case.

Choices: OFF (the same brightness as the STANDARD

DIMMER setting), –1 to –3 (based on the

STANDARD DIMMER setting), DISPLAY OFF

SCROLL (Front panel display scroll)

Use to select the mode to display information in the front

panel display when operating your iPod or XM Satellite

Radio.

Choices: CONT., ONCE

• Select CONT. to continue to scroll the display.

• Select ONCE to scroll the display to the end once, after

which the first 15 characters appear and stay.

■ OSD SET (OSD settings)

Use to adjust the display position and to set the display

time of the OSD.

OSD SHIFT (OSD shift)

Use to adjust the vertical position of the OSD. Adjust

toward the – (minus) direction to raise the position of the

OSD, and adjust toward the + (plus) direction to lower it.

Choices: –5 to +5

Initial setting: 0

OSD DISPLAY TIME (OSD display time)

Use to set the interval for which the OSD screen is

displayed after an operation.

Choices: ON, 10s, 30s

• Select ON to show the OSD screen constantly.

• Select 10s to turn off the OSD screen 10 seconds after

an operation.

• Select 30s to turn off the OSD screen 30 seconds after

an operation.

The OSD display time setting is available for your iPod and XM

Satellite Radio. For details, see pages 52 and 55 in the Reference

Guide.

■ UNIT SET (Unit settings)

Use this to change the display unit of measurement.

Choices: METERS, FEET

• Select METERS to enter distances in meters.

• Select FEET to enter distances in feet.

If you change this setting, the adjusted sound beam settings may

change.

DISPLAY MENU

A)F.DISPLAY SET

B)OSD SET

C)UNIT SET

[ ]/[ ]:Up/Down

[ENTER]:Enter

4)DISPLAY MENU

STANDARD DIMMER;;;;;OFF

AUTO DIMMER

;;;;;;;;;;;;;OFF

SCROLL;;;;;;;;;;;;CONT.

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

A)F.DISPLAY SET

Note

OSD SHIFT;;;;;;;;;;0

OSD DISPLAY TIME;;;ON

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

[ENTER]:Return

B)OSD SET

METERS FEET

[ ]/[ ]:Select

[ENTER]:Return

C)UNIT SET

Adjusting the audio balance

87 En

ADVANCED

OPERATION

English

You can adjust the sound beam output level of each channel by using the test tone or the audio output being played back

in each beam mode to achieve a more true-to-life surround sound experience.

You can use the test tone feature to output a test tone from

each channel to manually balance the channel levels.

Use this to set the channel levels so that the volume level

of each channel is identical when heard from your

listening position.

1 Set the operation mode selector to YSP.

2 Press TEST.

“TEST FRONT L” appears in the front panel display

and a test tone is output from the front left channel.

3 Press / to select the channel you want

to adjust.

The front panel display changes as follows:

“TEST SUBWOOFER” is only available when a subwoofer

is connected to this unit and SUBWOOFER is selected for

BASS OUT in SOUND MENU (see page 80).

4 Press / to adjust the channel volume.

Control range: –10.0 dB to +10.0 dB

Adjusting the audio balance

Using the test tone

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

CODE SET

ENTRY

CAT/

A-E

YSP

TV/AV

YSP

TV/AV

TEST

TEST FRONT L

Note

ENTER

TEST FRONT L

TEST CENTER

TEST FRONT R

TEST SUR.R

TEST SUR.L

TEST SUBWOOFER

ENTER

88 En

Adjusting the audio balance

5 Press TEST when you have completed all

your adjustments.

• All channel levels cannot be adjusted when the 2-channel or 5-

channel stereo playback (see page 62), My Beam (see page 63),

or My Surround (see page 57) is selected as the beam mode.

• “FRONT L/R” cannot be adjusted when Stereo plus 3 Beam is

selected as the beam mode (see page 57).

• “FRONT L/R” are automatically adjusted depending on the

settings of the other channels when Stereo plus 3 Beam or

stereo playback is selected as the beam mode (see pages 57 and

62).

If the level of a particular channel cannot be adjusted, “– –dB”

appears in the front panel display.

You can also manually adjust the channel levels while

playing back an input source such as a DVD.

1 Set the operation mode selector to YSP.

2 Press CH LEVEL repeatedly (or press

CH LEVEL and / ) to select the channel

you want to adjust.

The front panel display changes as follows.

“SWFR” is available only when a subwoofer is connected to

this unit and SUBWOOFER is selected for BASS OUT in

SOUND MENU (see page 80).

Notes

Using the audio output being

played back

TEST

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

CODE SET

ENTRY

CAT/

A-E

YSP

TV/AV

Note

YSP

TV/AV

CH LEVEL

ENTER

CH LEVEL

FRONT L +1.0dB

CENTER -2.5dB

FRONT R +1.0dB

SUR.R +2.0dB

SUR.L +2.0dB

SWFR --dB

89 En

Adjusting the audio balance

ADVANCED

OPERATION

English

3 Press / to adjust the channel volume.

Control range: –10.0 dB to +10.0 dB

4 Wait for a few seconds without operating this

unit when you have completed your

adjustment.

• All channel levels cannot be adjusted when the 2-channel or 5-

channel stereo playback (see page 62), or My Surround (see

page 57) is selected as the beam mode.

• “FRONT L/R” cannot be adjusted when Stereo plus 3 Beam is

selected as the beam mode (see page 57).

• Only CENTER can be adjusted when My Beam is selected as

the beam mode (see page 63).

• “FRONT L/R” are automatically adjusted depending on the

settings of the other channels when Stereo plus 3 Beam or

stereo playback is selected as the beam mode (see pages 57 and

62).

If the level of a particular channel cannot be adjusted, “– –dB”

appears in the front panel display.

Notes

ENTER

Selecting the input mode

90 En

You can select the type of audio input signals of the selected input source according to your preference or the conditions

of the input source. This function is available for TV/STB, DVD, AUX1, and AUX2.

We recommend setting the input mode to AUTO in most cases.

1 Set the operation mode selector to YSP.

2 Press one of the input selector buttons to

select the desired input source.

3 Press INPUTMODE repeatedly to toggle

between input modes.

ANALOG is not available as the input mode of DVD and

AUX2.

•AUTO

Automatically selects audio input signals in the following

priority order:

1) HDMI

2) Digital

3) Analog

Use this input mode in most cases.

•DTS

Selects only digital signals encoded in DTS.

Compared to AUTO, this input mode provides greater

stability while playing back CDs or LDs encoded in DTS.

•ANALOG

Selects only analog signals.

Even when both digital and analog signals are input

simultaneously, only analog signals are selected.

You can adjust the default input mode to be selected when the

power of this unit is turned on by adjusting INPUT MODE in

INPUT MENU (see page 82).

Selecting the input mode

STEREO

MY BEAM MY SUR.

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

ENTER

SUR. DECODEOFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

ENTRY

CAT/

A-E

321

AUX1 AUX2

STB

DVD

AUX3

DOCK

+10

789

YSP

TV/AV

YSP

TV/AV

AUX2AUX1DVD

STB

Note

TV/STB AUTO

TV/STB DTS

TV/STB ANALOG

DVD AUTO

DVD DTS

AUX1 AUTO

AUX1 DTS

AUX1 ANALOG

INPUTMODE

When TV or STB is selected

as the input source

When DVD is selected

as the input source

When AUX1 is selected

as the input source

AUX2 AUTO

AUX2 DTS

When AUX2 is selected

as the input source

Adjusting the system parameters

91 En

ADVANCED

OPERATION

English

This unit has additional menus that are displayed in the front panel display. These menus offer additional operations to

adjust and customize the way this unit operates.

When “F.PANEL KEY” is set to “F.PANEL: OFF” (see page 92), STANDBY/ON on the front panel is ineffective. Use STANDBY/ON

on the remote control instead to adjust the system parameters.

Follow the procedure below to enter the system

parameters.

1 Press STANDBY/ON on the remote control to

turn off the power of this unit.

2 Press and hold INPUT on the front panel and

press STANDBY/ON on the remote control to

turn on the power of this unit.

“MEMORY PROTECT” is displayed in the front

panel display.

3 Release INPUT on the front panel.

4 Set the operation mode selector to YSP.

5 Use / to select the parameter to be set,

then press ENTER.

See the table on page 92 for the types of parameters.

6 Use / to select and change the parameter

setting.

See the table on page 92 for the parameter settings.

Adjusting the system parameters

Note

Using the system parameters

STANDBY/ON

VOLUME

INPUT

ENHANCER MENU

RETURNDISPLAY

ENTER

ENTRY

CAT/

A-E

YSP

TV/AV

PRESET/TUNE

MEMORYSEARCH

CATFM/XM

MACRO

INPUT1

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

STANDBY/ON

INPUT

STANDBY/ON

MEMORY PROTECT

INPUT

YSP

TV/AV

ENTER

92 En

Adjusting the system parameters

Parameter to be changed and front panel display Parameter settings

MEMORY PROTECT

You can protect the settings you saved in the system memory of this unit from being

accidentally erased or unwantedly changed.

ON, OFF

MAX VOLUME

You can set the maximum volume level so that this unit will not output sound beyond the

limited volume level.

MAX, 99 to 01, MIN

Control step: 1

TURN ON VOLUME

You can set the initial volume level when the power of this unit is turned on.

MAX, 99 to 01, OFF

Control step: 1

MONITOR CHECK

Use this feature to activate or deactivate the monitor check function of this unit. When this

parameter is set to “YES”, this unit receives the information on the available video signal

resolutions from the video monitor connected via HDMI (see page 18). If your TV monitor is

not compatible with 1080i and/or 720p of resolutions, you cannot select “1080i” and/or

“720p” in “UP-SCALING” (see page 84).

YES, SKIP

If you change the setting of

“MONITOR CHECK”,

“UP-SCALING” is

automatically set to “OFF”

(see page 87).

DEMO MODE

You can test the sound beam output from this unit to experience the sound beam.

ON, OFF

PANEL INPUT KEY

You can disable the INPUT on the front panel when you adjust the system parameters.

ON, OFF

Disabling the front panel keys

You can disable the front panel keys except when you adjust the system parameters.

ON, OFF

MEMORY PROTECT

MAX VOLUME SET

TURN ON VOLUME

MONITOR CHECK

Note

DEMO MODE

PANEL INPUT KEY

F.PANEL KEY

93 En

Adjusting the system parameters

ADVANCED

OPERATION

English

7 Press STANDBY/ON on the remote control to

set this unit to the standby mode.

The new setting will be activated when you turn on the

power of this unit next time.

When the demo mode is turned on, restart the unit, then press

ENTER while playing back sources to test the sound beam.

The sound beam being output shuttles between left and right.

Press ENTER again to stop shuttling.

FACTORY PRESET

You can reset all of the parameters of this unit to the factory presets. This procedure

completely resets ALL the parameters in SET MENU.

After performing the following procedure you must run AUTO SETUP again to match your surround

sound environment.

RESET, CANCEL

Parameter to be changed and front panel display Parameter settings

Note

FACTORY PRESET

STANDBY/ON

Remote control features

94 En

In addition to controlling this unit, the remote control can also operate other AV components made by Yamaha and other

manufacturers. To control other components, you must set up the remote control with the appropriate remote control

codes and set the operation mode selector to TV/AV to change the control area.

Depending on the external AV component you are using, you may not be able to operate the component with the remote control, even if

a remote control code is set. In this case, operate the component using the supplied remote control.

You can control other components by setting the

appropriate remote control codes. Codes can be set up for

each input area (DVD, AUX1, AUX2, STB, and TV).

For a complete list of available remote control codes, refer

to “List of remote control codes” at the end of this manual.

Write down the code of the external component

whose remote control codes you want to set,

as indicated on the “List of remote control

codes” at the end of the manual.

If there is more than one code, try them one at a time.

Press and hold CODE SET and press one of the

input selector buttons to select the input source

you want to set a remote control code for.

The transmission indicator flashes twice and remains lit.

Proceed to step 3 while holding down CODE SET.

Press and hold CODE SET until step 3 is

finished.

3 Press the numeric buttons to enter the

remote control code while holding down

CODE SET.

Release CODE SET after entering the code.

4 Refer to “Controlling other components” on

page 95 to operate the external component

using the remote control.

If the external component functions correctly the

remote control code setup is successful.

If the external component does not function correctly,

the remote control code may be incorrect. Confirm

that the remote control code is correct. See “List of

remote control codes” at the end of this manual and

start over from step 1.

If the manufacturer of your component has more than one code,

try each of them until you find the correct one.

Remote control features

Note

Setting remote control codes

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

CODE SET

STEREO

MY BEAM MY SUR.

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER

SUR. DECODEOFF

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

321

AUX1 AUX2

STB

DVD

AUX3

DOCK

+10

789

Transmission indicator

TV MUTE

CODE SET

While holding

down, press

AUX2AUX1DVD

STB

Note

If the remote control is without batteries for more than

two minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries and reset the remote control codes.

When changing the batteries, be careful not to press

any of the buttons on the remote control. Doing so will

clear the contents of the memory.

SPORTS

MY SUR.

SPORTS

Setting example: Yamaha DVD input area

TV MUTE

CODE SET

While holding

down, press

95 En

Remote control features

ADVANCED

OPERATION

English

■ Operating your TV

Set the operation mode selector to TV/AV, and

press TV to select TV as the input source.

The control area of the remote control changes to the TV

operation mode.

1 Numeric buttons

Selects a TV channel for playback.

2 CH +/–

Switches between the available TV channels.

3 TV INPUT

Switches the input source for your TV.

4 TV POWER

Turns on or off the power of your TV.

5 TV INPUT1

Selects the input source of your TV.

6 TV VOL +/–

Adjusts the audio output level of your TV.

7 TV MUTE

Temporarily mutes audio output from your TV.

When using the HDMI control function, some operations

(switching of the power between on and standby,

adjustment of the volume, etc.) may be performed on this

unit when the TV connected to this unit using the HDMI

jacks is operated with this unit’s remote control. When a

DVD recorder or Blu-ray recorder compatible with HDMI

control is connected to this unit using the HDMI jacks, the

power of these devices may also be switched between on

and standby.

Controlling other components

YSP

TV/AV

STEREO

MY BEAM MY SUR.

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

SUR. DECODEOFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

321

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

+10

YSP

TV/AV

CAT/

A-E

ENTRY

96 En

Remote control features

■ Operating your DVD player/recorder

Set the operation mode selector to TV/AV and

press DVD to select DVD as the input source.

The control area of the remote control changes to the DVD

operation mode.

1 Numeric buttons

Enter numeric digits.

2 Cursor buttons / / / , ENTER

Use to select DVD menu items.

3 Operation buttons for DVD players

Operate your DVD player/recorder, such as play and stop.

4 AV POWER

Turns on or off the power of your DVD player/recorder.

5 MENU

Displays the DVD menu.

6 RETURN

Use to return to the previous DVD menu screen or exit

from the DVD menu.

■ Operating your STB

(CATV/Satellite tuner)

Set the operation mode selector to TV/AV and

press STB to select STB as the input source.

The control area of the remote control changes to the STB

operation mode.

1 Numeric buttons

Enter numeric digits.

2 CH +/–

Switches between the available STB channels.

3 AV POWER

Turns on or off the power of your STB.

DVD

YSP

TV/AV

STEREO

MY BEAM MY SUR.

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

SUR. DECODEOFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

321

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

+10

YSP

TV/AV

CAT/

A-E

ENTRY

STB

YSP

TV/AV

STEREO

MY BEAM MY SUR.

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER

RETURNDISPLAY

TV VOL

VOLUME

MUTE

TV INPUT TV MUTE

ENTER

SUR. DECODEOFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

321

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

+10

789

YSP

TV/AV

CAT/

A-E

ENTRY

97 En

Remote control features

ADVANCED

OPERATION

English

■ Operating your VCR

Set the operation mode selector to TV/AV and

press AUX1 to select VCR as the input source.

The control area of the remote control changes to the

AUX1 operation mode.

This operation is available when your VCR is connected to the

AUX1 AUDIO INPUT jacks on this unit.

1 Numeric buttons

Enter numeric digits.

2 CH +/–

Switches between the available VCR channels.

3 Operation buttons for VCR

Operate your VCR, such as play and stop.

4 AV POWER

Turns on or off the power of your VCR.

AUX1

YSP

TV/AV

STEREO

MY BEAM MY SUR.

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

SUR. DECODEOFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

321

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

+10

YSP

TV/AV

CAT/

A-E

ENTRY

98 En

Remote control features

The TV macro feature makes it possible to perform a

series of operations with the press of a single button. For

example, when you want to play a DVD, you would

normally turn on the component, select DVD as the input

source, and press the play button to start playback. The TV

macro feature lets you perform all of these operations

simply by pressing the DVD macro button.

• Be sure to set up a remote control code for your TV before

setting macros.

• The ways to set macros differ if your TV does not have the

tuning capability.

• If you press any control buttons on the remote control other than

the ones used to set macros while setting macros, the setting

procedure is automatically canceled.

• If it takes more than 10 seconds in steps 2 and 3, the setting

procedure is automatically canceled. In this case, repeat from

step 1.

■ Setting macros for the TV with the

tuning capability

1 Press and hold CODE SET and press one of

the input selector buttons to select the input

source you want to set macros for.

Proceed to step 2 while holding down CODE SET.

2 Press MACRO while holding down CODE

SET.

3 Press CH +/– or the numeric buttons to select

the TV channel.

Check that the TV screen changes to the tuner screen.

4 Press TV INPUT repeatedly until the screen

changes to the display of the input source

selected in step 1.

5 Press ENTER to confirm the macro setting.

Using the TV macro

Notes

STEREO MY SUR.

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

SUR. DECODE

OFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

INPUT1

ENTRY

CAT/

A-E

321

AUX1 AUX2

STB

DVD

AUX3

POWERPOWERSTANDBY/ON

DOCK

+10

YSP

TV/AV

TV MUTE

CODE SET

AUX2AUX1DVD

STB

While holding

down, press

TV MUTE

CODE SET

MACRO

While holding

down, press

STEREO

OFF

789

+10

5BEAM

ST+3BEAM

3BEAM

MY SUR.

MY BEAM

MUSIC MOVIE SPORTS

TV INPUT

ENTER

99 En

Remote control features

ADVANCED

OPERATION

English

■ Setting macros for the TV without the

tuning capability

1 Press and hold CODE SET and press one of

the input selector buttons to select the input

source you want to set macros for.

Proceed to step 2 while holding down CODE SET.

2 Press MACRO while holding down CODE

SET.

3 Press INPUT1.

Check that the TV screen changes to the input 1

screen.

4 Press TV INPUT repeatedly until the screen

changes to the display of the input source

selected in step 1.

5 Press ENTER to confirm the setting.

■ Operating macros

Press and hold one of the input selector buttons

for approximately two seconds to select the input

source you want to operate macros for.

The TV input changes at the same time the input mode

changes.

■ Canceling the macros

1 Press and hold CODE SET and press one of

the input selector buttons to select the input

source you want to cancel the macros for.

Proceed to step 2 while holding down CODE SET.

2 Press MACRO while holding down CODE

SET.

3 Press ENTER to cancel the macros.

TV MUTE

CODE SET

While holding

down, press

AUX2AUX1DVD

STB

TV MUTE

CODE SET

MACRO

While holding

down, press

INPUT1

TV INPUT

ENTER

AUX2AUX1DVD

STB

TV MUTE

CODE SET

While holding

down, press

AUX2AUX1DVD

STB

TV MUTE

CODE SET

MACRO

While holding

down, press

ENTER

Troubleshooting

100 En

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below

or if the instruction below does not help, set this unit to the standby mode, disconnect the AC power supply cable, and

contact the nearest authorized Yamaha dealer or service center.

■ General

Troubleshooting

Problem Cause Remedy

See

page

This unit fails to turn on

when STANDBY/ON is

pressed, or enters the

standby mode soon after the

power has been turned on.

The AC power supply cable is not firmly

connected to the AC wall outlet.

Connect the AC power supply cable firmly

to the AC wall outlet.

This unit has been exposed to a strong

external electric shock (such as lightning

and strong static electricity).

Set this unit to the standby mode, disconnect

the AC power supply cable, plug it back in

after 30 seconds, and use it normally.

—

This unit suddenly enters the

standby mode.

The internal temperature becomes too high

and the overheat protection circuitry has

been activated.

Wait for about one hour for this unit to cool

down and turn it back on.

—

The sleep timer has turned the unit off. Turn on the power and play back the source

again.

—

No sound. Incorrect input or output cable connections. Connect the cables properly. If the problem

persists, the cables may be defective.

No appropriate input source has been

selected.

Select an appropriate input source with

INPUT or the input selector buttons.

The volume is turned down. Turn up the volume.

The sound is muted. Press MUTE or VOLUME +/– to resume

audio output and adjust the volume level.

The signals this unit cannot reproduce (such

as PCM signals with more than 96 kHz of

sampling frequency) are being received

from the source component.

Play a source whose signals can be

reproduced by this unit.

—

Change the system settings of the source

component.

—

The HDMI components connected to this

unit do not support the HDCP copy

protection standards.

Connect the HDMI components that support

the HDCP copy protection standards.

SUPPORT AUDIO is set to OTHER and

HDMI audio signals are not being played

back on this unit.

Set SUPPORT AUDIO to YSP-3050 in

MANUAL SETUP

The sound suddenly goes

off.

The sleep timer has turned this unit off. Turn on the power and play back the source

again.

—

The sound is muted. Press MUTE or VOLUME +/– to resume

audio output and adjust the volume level.

No sound from the effect

channels.

You are playing back the source or program

in the 2-channel stereo playback or My

Beam mode.

Press one of the beam mode buttons on the

remote control to select a multi-channel

playback mode and play back the source or

program once more.

No sound from the center

channel.

The output level of the center channel is set

to minimum.

Raise the level of the center channel.

No sound from the surround

channels.

The output level of the surround channels is

set to minimum.

Raise the output level of the surround

channels.

101 En

Troubleshooting

ADDITIONAL

INFORMATION

English

Problem Cause Remedy

See

page

No sound from the

subwoofer.

BASS OUT in SUBWOOFER SET is set to

FRONT.

Select SUBWOOFER.

The source does not contain low bass signals.

Distorted or too little bass

sound.

CROSS OVER in SUBWOOFER SET is set

incorrectly.

Set CROSS OVER correctly.

One of the night listening enhancers is

currently selected.

Turn off the night listening enhancers.

Too much bass sound. TruBass is currently turned on. Turn off TruBass.

The volume level of the subwoofer is too high.

Turn down the volume level of the subwoofer.

—

Surround sound effects are

insubstantial.

The listening room is not a regular shape. Install this unit in a square or rectangular

shaped room.

—

There is no wall in the path of the sound

beam.

Try placing a flat object, such as a board, in

the path of the sound beam.

—

Dolby Digital or DTS sources

cannot be played back.

(Dolby Digital or DTS

indicator does not light up in

the front panel display.)

The connected component is not set to

output Dolby Digital or DTS digital signals.

Make an appropriate setting following the

operating instructions for your component.

—

The input mode is set to ANALOG. Set the input mode to AUTO.

There is noise interference

when a subwoofer is not

connected to this unit.

The protection circuitry was in operation

because a source with strong bass elements

was played back.

Turn down the volume level.

Select SUBWOOFER for BASS OUT.

Connect a subwoofer and adjust settings for

SUBWOOFER SET.

Low-frequency sounds are

distorted.

CROSS OVER in SUBWOOFER SET is set

incorrectly.

Set CROSS OVER correctly.

On-screen display does not

appear.

The OSD video pin cable is not connected

properly.

Connect the cable properly.

This unit does not operate

properly.

The internal microcomputer has been frozen

by an external electric shock (such as

lightning or excessive static electricity) or

by a power supply with low voltage.

Disconnect the AC power supply cable from

the outlet and plug it in again after about 30

seconds.

—

No sound is heard from the

TV connected via HDMI.

The TV does not accept the multi-channel

audio signals.

Convert the multi-channel audio signals to

the 2-channel audio signals at the source

component such as a DVD player.

—

“SUPPORT AUDIO” is set to “YSP-3050”. Set “SUPPORT AUDIO” to “OTHER”.

There is noise interference

from digital or high-

frequency equipment.

This unit is too close to the digital or high-

frequency equipment.

Move this unit farther away from such

equipment.

—

This unit does not output

effect sounds properly.

The original source includes surround effects.

Disable the surround effect settings of this unit.

—

My Beam auto-adjust

function does not work.

The listening room is too noisy. Keep the listening room as quiet as possible.

—

Try manual-adjust function.

The sound reflectivity of the listening room

is too much.

Set REFLECTING to HI ECHO.

The remote control may be operated outside

of the remote control operation range.

The remote control functions within a

maximum range of 6 m (20 ft) and no more

than 45 degrees off-axis from the front

panel.

The function does not work properly

because of the condition of the connected

components.

Select My Beam and then try again.

102 En

Troubleshooting

■ Remote control

■ HDMI

■ FM tuner

Problem Cause Remedy

See

page

The remote control does not

work and/or function

properly.

Wrong distance or angle. The remote control functions within a

maximum range of 6 m (20 ft) and no more

than 45 degrees off-axis from the front panel.

Direct sunlight or lighting (from an inverter

type of fluorescent lamp, etc.) is striking the

remote control sensor of this unit.

Reposition this unit.

—

The batteries are weak. Replace all batteries.

Cannot operate external

components with the remote

control of this unit.

The external component you want to operate

is not selected as the input source.

Press INPUT on the front panel or the input

selector buttons on the remote control to

select the external component you want to

operate.

The remote control code was not correctly

set.

Set the remote control code correctly or try

another code for the same manufacturer

using the “List of remote control codes” at

the end of this manual.

Even if the remote control code is correctly

set, there are some models that do not

respond to the remote control.

Use the remote control supplied with the

external component.

—

The cursor buttons do not

work during SET MENU

operation.

The operation mode selector was

unwantedly set to TV/AV.

Set the operation mode selector to YSP.

—

Cannot use the My Beam

auto-adjust function.

Wrong distance or angle. The remote control functions within a

maximum range of 6 m (20 ft) and no more

than 45 degrees off-axis from the front panel.

Error message Cause Remedy

See

page

Device Error The number of the connected HDMI

components exceeds the limit.

Reduce the number of the connected HDMI

components.

—

HDCP Error HDCP authentication failed. Check that the connected HDMI

components support the HDCP copy

protection standards.

—

Out of Resolution The resolution of the HDMI output signals

exceeds the limit allowed by your TV.

Adjust UP-SCALING.

Problem Cause Remedy

See

page

FM stereo reception is noisy. The characteristics of FM stereo broadcasts

may cause this problem when the

transmitter is too far away or the antenna

input is poor.

Check the antenna connections.

Try using a high-quality directional FM

antenna.

—

Use the manual tuning method.

There is distortion, and clear

reception cannot be obtained

even with a good FM

antenna.

There is multi-path interference. Adjust the antenna position to eliminate

multi-path interference.

—

The desired station cannot

be tuned into with the

automatic tuning method.

The signal is too weak. Use a high-quality directional FM antenna.

—

Use the manual tuning method.

Previously preset stations

can no longer be tuned into.

This unit has been disconnected for a long

period.

Preset the stations again.

103 En

Troubleshooting

ADDITIONAL

INFORMATION

English

■ XM Satellite Radio

■ iPod

In case of a transmission error with no status message appearing in the front panel display and in the OSD, check the connection

between your iPod and this unit.

Status message Cause Remedy

See

page

CHECK ANTENNA

XM Mini-Tuner and Home Dock are not

connected to the XM jack of this unit or

not working properly.

Check XM Mini-Tuner and Home Dock connections

and adjust the orientation for the best reception level.

UPDATING

The XM user encryption code is being

updated.

Wait until the encryption code is updated. —

NO SIGNAL

The signal is too weak. Adjust the orientation of the indoor antenna of Home

Dock for the best reception level.

It takes longer than four seconds to decode

audio or text data.

Wait until the decoding process is finished. —

OFF AIR

The currently selected XM channel is not

broadcasting signals.

Check the channel number again or select another

XM channel.

—

<XM> - - -

The Channel Station ID (SID) is no longer

available.

- - - / - - -

No artist name or song title is available.

<CAT> - - -

No channel is available for the selected

category.

Select another channel category by pressing

CAT/A-E repeatedly.

Note

Status message Cause Remedy

See

page

This unit is in the middle of recognizing

the connection with your iPod.

This unit is in the middle of acquiring the

song lists from your iPod.

Connect error

There is a problem with the signal path

from your iPod to this unit.

Turn off this unit and reconnect the Yamaha iPod

universal dock to the DOCK terminal of this unit.

Try resetting your iPod. —

Unknown iPod

Your iPod is not supported by this unit. Only iPod (Click and Wheel), iPod nano, and iPod

mini are supported.

—

iPod connected

The connection between your iPod and

this unit is completed.

Disconnected

Your iPod is removed from the Yamaha

iPod universal dock.

Set your iPod back in the Yamaha iPod universal

dock.

Unable to play

This unit cannot play back the files stored

on your iPod.

Check the playability of the files stored on your iPod. —

Store other playable music files on your iPod. —

Glossary

104 En

■ Dolby Digital

Dolby Digital is a digital surround sound system that gives

you completely independent multi-channel audio. With 3

front channels (left, center, and right) and 2 surround

stereo channels, Dolby Digital provides 5 full-range audio

channels. With an additional channel especially for bass

effects, called LFE (low-frequency effect), the system has

a total of 5.1-channels (LFE is counted as 0.1-channel).

By using 2-channel stereo for the surround channels, more

accurate moving sound effects and surround sound

environment are possible than with Dolby Surround. The

wide dynamic range (from maximum to minimum

volume) reproduced by the 5 full-range channels and the

precise sound orientation generated using digital sound

processing provide listeners with excitement and realism

previously unheard of.

With this unit, any sound environment from monaural up

to a 5.1-channel configuration can be freely selected for

your enjoyment.

■ Dolby Pro Logic II

Dolby Pro Logic II is an improved technique used to

decode vast numbers of existing Dolby Surround software.

This new technology enables a discrete 5-channel

playback with 2 front left and right channels, 1 center

channel, and 2 surround left and right channels (instead of

only 1 surround channel for conventional Pro Logic

technology). Music and Game modes are also available for

2-channel sources in addition to the Movie mode.

■ Dolby Surround

Dolby Surround uses a 4-channel analog recording system

to reproduce realistic and dynamic sound effects: 2 front

left and right channels (stereo), a center channel for dialog

(monaural), and a surround channel for special sound

effects (monaural). The surround channel reproduces

sound within a narrow frequency range.

Dolby Surround is widely used with nearly all video tapes

and laser discs, and in many TV and cable broadcasts as

well. The Dolby Pro Logic decoder built into this unit

employs a digital signal processing system that

automatically stabilizes the volume on each channel to

enhance moving sound effects and directionality.

■ DTS Digital Surround

DTS digital surround was developed to replace the analog

soundtracks of movies with a 6-channel digital sound

track, and is now rapidly gaining popularity in movie

theaters around the world. DTS, Inc. has developed a

home theater system so that you can enjoy the depth of

sound and natural spatial representation of DTS digital

surround in your home. This system produces practically

distortion-free 6-channel sound (technically, left, right,

and center channels, 2 surround channels, plus an LFE

0.1-channel as a subwoofer, for a total of 5.1 channels).

The unit incorporates a DTS-ES decoder that enables 6.1-

channel reproduction by adding the surround back channel

to existing 5.1-channel format.

■ DTS Neo:6

Neo:6 decodes the conventional 2-channel sources for 6-

channel playback by the specific decoder. It enables

playback with the full-range channels with higher

separation just like digital discrete signal playback. Two

modes are available: Music mode for playing music

sources and Cinema mode for movies.

■ EUPHONY

Euphony is a revolutionary sound field reproduction

system implemented with state-of-the-art sound

technologies developed under the basic concept of

enjoying beautiful sound. It can reproduce surround sound

optimized without depending on the number of input

channels, the number of speakers (two or more speakers)

or the speaker’s dimensions. In addition, it features steady

center localization. It also can reproduce the surround

sound for the headphones with natural sound and “out-of-

head” localization so that the listener feels an expanded

sound and will not tire, even when listening to music or a

movie for long time.

■ HDMI

HDMI (High-Definition Multimedia Interface) is the first

industry-supported, uncompressed, all-digital audio/video

interface. Providing an interface between any source (such

as a set-top box or AV receiver) and an audio/video

monitor (such as a digital television), HDMI supports

standard, enhanced, or high-definition video as well as

multi-channel digital audio using a single cable. HDMI

transmits all ATSC HDTV standards and supports 8-

channel digital audio, with bandwidth to spare to

accommodate future enhancements and requirements.

When used in combination with HDCP (High-bandwidth

Digital Content Protection), HDMI provides a secure

audio/video interface that meets the security requirements

of content providers and system operators. For further

information on HDMI, visit the HDMI website at

“http://www.hdmi.org/”.

Glossary

105 En

Glossary

ADDITIONAL

INFORMATION

English

■ LFE 0.1-channel

This channel is for the reproduction of low bass signals.

The frequency range for this channel is 20 Hz to 120 Hz.

This channel is counted as 0.1 because it only enforces a

low-frequency range compared to the full-range

reproduction by the other 5/6 channels in Dolby Digital or

DTS 5.1/6.1-channel systems.

■ Neural Surround

Neural Surround

™

represents the latest advancement in

surround technology and has been adopted by XM

Satellite Radio for digital radio broadcast of surround

recordings and live events in surround sound. Neural

Surround

™

employs psychoacoustic frequency domain

processing which allows delivery of a more detailed sound

stage with superior channel separation and localization of

audio elements.

■ PCM (Linear PCM)

Linear PCM is a signal format under which an analog

audio signal is digitized, recorded, and transmitted

without using any compression. This is used as a method

of recording CDs and DVD audio. The PCM system uses

a technique for sampling the size of the analog signal per

very small unit of time. Standing for pulse code

modulation, the analog signal is encoded as pulses and

then modulated for recording.

■ SRS TruBass

SRS TruBass is a psychoacoustic bass enhancement

technology developed by SRS Labs, Inc. for speakers and

headphone systems that delivers bass up to an octave

below the physical capabilities of the speaker’s driver.

SRS TruBass technology takes advantage of a

spontaneous tendency of the human ears to infer low-

range audio data when presented with higher-frequency

harmonic signals. As a result, our ears can hear the

original low-range sound that the speaker system is

incapable of producing.

Index

106 En

■ Numerics

3 Beam............................................................................ 57

5 Beam............................................................................ 56

■ A

AC power supply cable................................................... 23

Audio pin cable............................................................... 17

AUTO SETUP (IntelliBeam) ......................................... 29

■ B

Battery ............................................................................ 24

BEAM MENU................................................................ 76

Beam mode......................................................... 56, 62, 63

■ C

Cable clamp.................................................................... 17

Cardboard microphone stand.......................................... 31

CINEMA DSP................................................................ 66

■ D

DEMO MODE................................................................ 92

Demonstration DVD......................................................... 6

Digital audio pin cable.................................................... 17

DISPLAY MENU........................................................... 86

Dolby Digital.................................................................. 58

Dolby Pro Logic ............................................................. 58

Dolby Pro Logic II.......................................................... 58

DTS ................................................................................ 58

DTS Neo: 6..................................................................... 58

Dynamic range................................................................ 81

■ E

EUPHONY................................................................... 104

■ F

FACTORY PRESET....................................................... 93

Fastener........................................................................... 15

Front panel........................................................................ 7

Front panel display ........................................................... 8

■ H

HDMI ............................................................................. 17

HDMI cable.................................................................... 17

■ I

IntelliBeam ..................................................................... 29

IntelliBeam microphone ................................................. 30

■ L

LFE 0.1-channel ........................................................... 105

■ M

MANUAL SETUP..........................................................74

MEMORY....................................................................... 36

Movie program ...............................................................66

Music program................................................................66

My Beam ........................................................................ 63

■ N

Night listening enhancer .................................................69

■ O

On-screen display (OSD)................................................ 26

Optical cable ...................................................................17

OSD video pin cable.......................................................17

■ P

PCM..............................................................................105

Power .............................................................................. 25

■ R

Rear panel .........................................................................9

Remote control................................................................10

Remote control code .......................................................94

Remote control sensor .................................................... 24

■ S

SET MENU .................................................................... 26

Sleep timer ...................................................................... 70

Sound field program ....................................................... 65

Stereo plus 3 Beam .........................................................57

Surround mode................................................................ 58

Surround sound............................................................... 56

SOUND MENU..............................................................80

Sports program................................................................66

Stereo sound.................................................................... 62

System parameter............................................................ 91

■ T

Test tone.......................................................................... 87

TruBass ........................................................................... 81

TV macro ........................................................................ 98

TV volume equal mode...................................................69

■ V

Volume ............................................................................ 41

Volume mode .................................................................. 69

Index

Specifications

107 En

ADDITIONAL

INFORMATION

English

AMP SECTION

• Maximum Output Power

................................................. 2 W (1 kHz, 10% THD, 4 Ω) × 21

20 W (100 Hz, 10% THD, 4 Ω) × 2

SPEAKER SECTION

•Driver

Small dia. speakers

...................... 4 cm (1-9/16 in) cone magnetic shielding type × 21

Woofers

.................... 10 cm (3-15/16 in) cone magnetic shielding type × 2

• Frequency response ................................................. 60 Hz to 20 kHz

(–10 dB, stereo mode)

CONNECTIONS

• Input Jacks

TV/STB, AUX 1 AUDIO IN (1 V, 32 kΩ) .......... 2 pairs (Analog)

TV/STB, AUX 1 OPTICAL DIGITAL IN ....... 2 (Optical digital)

DVD, AUX 2 COAXIAL DIGITAL IN ........... 2 (Coaxial digital)

STB, DVD HDMI IN ....................................................................2

DVD VIDEO INPUT.............................................. 1 (Component)

STB VIDEO INPUT.................................................1 (Composite)

AUX 3 ...........................................................................................1

• Output Jacks

SUBWOOFER OUT (1.5 V, less than 120 Hz) ...... 1 (Subwoofer)

VIDEO OUT (1 Vp-p, 75 Ω) ............................................1 (OSD)

HDMI OUT ..................................................................................1

• System Connector Jack

INTELLIBEAM MIC .................................. 1 (Microphone input)

FM SECTION

• Tuning Range ...................................................... 87.5 to 107.9 MHz

GENERAL

• Power Supply ......................................................... AC 120 V, 60 Hz

• Power Consumption ................................................................. 36 W

• Standby Power Consumption ...................................... 0.1 W or less

• Dimensions (W x H x D) ................................ 800 × 155 × 152 mm

(31-1/2 x 6-3/32 x 5-31/32 in)

• Weight ............................................................. 11.5 kg (25 lbs 6 oz)

Specifications are subject to change without notice.

Specifications

HDMI interface of this unit is based on the following standard:

• HDCP (High-bandwidth Digital Content Protection System)

licensed by Digital Content Protection, LLC.

List of remote control codes

ADMIRAL 292, 293, 216

AIWA 294, 276, 283, 284

AKAI 295, 296

ALBA

296

AOC 297

BELL &

HOWELL 292

BESTAR 298

BLAUPUNKT 229, 222

BLUE SKY 298

BRANDT 223

BROC SONIC 297

BUSH 296

BYD:SIGN 201, 202

CLATRONIC 298

CRAIG 224

CROSLEX 225, 298

CURTIS MATHIS

297, 226

DAEWOO 297, 298, 224,

227, 228

DAYTRON 239

DUAL 298

DWIN 293, 281

EMERSON 297, 224, 239, 232

FURGUSON 223, 265, 266

FIRST LINE 298

FISHER 295, 233

FRABA 298

FUJITSU 289

FUNAI 277, 278

GE 293, 297, 234,

235, 236

GOODMANS 296, 298, 223

GRUNDIG 229, 238, 249

HITACHI 297, 239, 242,

243, 285, 206

ICE 296

IRRADIO 296

ITT/NOKIA 244, 245

JC PENNY 293, 297, 234, 237

JVC 296, 246, 247, 286

KENDO 298

KTV 297, 239

LG/GOLDSTAR

297, 298, 239, 237

LOEWE 298, 248, 207

LXI 293, 297, 225,

226, 233, 298

MAGNAVOX 297, 225, 239, 298

MARANTZ 298, 210

MATSUI 295

MEDION 203, 204, 298

MEMOREX 297, 216

MITSUBISHI 299, 297, 259, 287

NAD 226, 255

NEC 297, 252, 282

NOKIA 244, 245

NOKIA OCEANIC

245

NORDMENDE 265, 266

ONWA 296

PANASONIC 234, 235, 236,

253, 288, 211

PHILCO 297, 225, 239, 298

PHILIPS 298, 225, 205

PIONEER 226, 235, 254,

255, 268

PORTLAND 297, 256

PROSCAN 293, 221

PROSCAN 231, 241, 251

PROTON 297, 250, 260, 270

QUASAR 234, 235

RADIO SHACK299, 293, 297

RCA 293, 297, 234,

256, 257, 258, 221

RUNCO 220, 230, 271

SABA 223, 269, 265, 266

SAMPO 281, 297, 280

SAMSUNG 297, 239, 248,

262, 275

SANYO 295, 233, 279,

272, 273, 274, 212

SCHNEIDER 296

SCOTT 297

SHARP 292, 239, 232,

213, 208

SIEMENS 229

SIGNATURE 216

SIGNATURE 292

SONY 263, 214

SYLVANIA 297, 225, 298

SYNPHONIC 217, 218, 219

TELEFUNKUN269, 264, 265, 266

THOMSON 223, 266

TOSHIBA 292, 226, 267, 215

VIDECH 297, 242

WARDS 297, 239, 232, 216

YAMAHA 299, 292, 242,

285, 287, 253, 206

YA M A J I 2 9 8

ZENITH 216, 261, 271

DVD PLAYER

AIWA 648, 649

APEX DIGITAL

652, 653, 654

BYD:SIGN 678, 679

DAEWOO 655

DENON 623, 624, 682

FUNAI 625

HARMAN/KARDON

656, 657

HITACHI 626, 688, 689

JVC 627, 643, 692

KENWOOD 628

KLH 658

LG/GOLDSTAR

645, 663, 664

MARANTZ 699, 659

MITSUBISHI 629

ONKYO 632, 633, 634

PANASONIC 623, 635, 668,

672, 682, 683, 684

PHILIPS 699, 647, 659

PIONEER 636, 637, 638,

673, 674, 675, 685

686, 687

RCA 639

SAMSUNG 642

SHARP 643, 692

SONY 644, 676, 677

SYLVANIA 662

SYMPHONIC 662

THOMSON 646

TOSHIBA 634, 665, 666, 667

YAMAHA 699, 622, 623,

647, 682

ZERITH 663, 664

VCR

ADMIRAL 395

AIWA 396, 397, 398, 329

AKAI 322, 323, 324

AUDIO DYNAMIC

392, 394

BELL & HOWELL

393

BLAUPUNKT 325, 326

BROC SONIC 327

BUSH 322

CANON 325, 328

CGM 396, 332

CITIZEN 396

CRAIG 396, 363

CURTHIS MATHIS

397, 328, 333

DAEWOO 328, 334, 335

DBX 392, 394

DIMENSIA 333

DYNATECH 397

EMERSON 327, 334, 396, 397

FISHER 393, 336

FUNAI 397

GE 328, 333, 387

GO VIDEO 321, 331, 341,

351, 363

GOODMANS 334, 337

GRUNDIG 332, 338

HITACHI 325, 333, 349,

342, 343

INSTANT REPLAY

325, 328

ITT/NOKIA 393

JC PENNY 392, 393, 394,

328, 333, 349,

396, 363

JVC 392, 394, 344,

345, 346, 347

KENDO 396

KENWOOD 392, 394, 396

LG/GOLDSTAR

396, 388

LOEWE 396, 337

LUXOR 395

LXI 393, 396, 397,

336, 349

MAGNAVOX 325, 326, 328

MARANTZ 392, 394

MARTA 396

MATSUI 396

MEMOREX 328, 336, 396, 397

MINOLTA 333, 349

MITSUBISHI 399, 344, 348,

359, 353, 352

MTC 363, 397

MULTITECH 397, 348, 354

NEC 392, 394, 344, 383

NOKIA 393, 395

NOKIA OCEANIC

395

OKANO 323

OLYMPIC 325, 328

ORION 327

PANASONIC 325, 328, 339,

355, 378, 384,

385, 386

PENTAX 333, 349

PHILCO 325, 328, 397

PHILLIPS 325, 326, 328,

337, 356, 357

PHONOLA 337

PILOT 396

PIONEER 325

QUASAR 325, 328

RCA/PROSCAN

325, 326, 328,

333, 335, 349,

358, 363, 397

REALISTIC 393, 397, 328,

336, 359, 362,

396, 363

SAMSUNG 354, 358, 363,

364, 365, 366

SANSUI 394

SANYO 393, 336, 367

SCHNEIDER 337

SCOTT 399, 335, 336,

348, 359, 354,

358, 352

SELECO 322

SHARP 395, 362, 382

SIEMENS 393

SIGNATURE 2000

395, 397

SONY 368, 379, 372,

373, 374, 375

SYLVANIA 397, 325, 326, 328

SYMPHONIC 397

TANDBERG 334

TANDY 397

TASHIRO 39 6

TATUNG 392, 394

TEAC 392, 394, 397

TECHNICS 325, 328

TEKNIKA 396

TELEFUNKUN

376, 377

THOMAS 397

THORN 393, 396

TOSHIBA 335, 389

TOTEVISION 363, 396

UNITECH 363

UNIVERSUM 396, 327, 376

VIDEOSONIC 363

W.WHOUSE 396

WARDS 395, 396, 336,

362, 397, 363

YAMAHA 399, 392, 393, 394

ZERITH 344, 361, 368,

371, 379, 396, 397

CABLE TV TUNER

ABC 739, 752, 753,

755, 758, 759, 762

GENERAL INSTRUMENT

722, 786, 787, 788

HAMIN 723, 724, 725,

726, 727

HITACHI 722

JEROLD 722, 728, 729,

732, 733, 734,

735, 736, 737

MAGNAVOX 738

MOTOROLA 748, 728

OAK 739, 742, 743

PANASONIC 744, 745, 746,

747, 783, 784

PHILLIPS 763, 764, 765,

766, 767, 768

PIONEER 748, 785, 747

RADIO SHACK749

RCA 744, 792, 793

SCIENTIFIC ATLANTA

752, 753, 754, 789

SONY 756, 757

TOCOM 755

UNIVERSAL 769, 772, 773,

774, 775

VIEWSTAR 764, 766, 776,

777, 778, 779, 782

SATELLITE TUNER

ECHOSTAR 822

GE 837, 838, 839

GENERAL INSTRUMENT

823

HITACHI 824

HUGHES 843, 844, 845, 846

JVC 822

MAGNAVOX 825

PANASONIC 826, 829

PHILLIPS 825, 843, 844,

845, 846, 847,

848, 849

PRIMESTAR 827

PROSCAN 837, 838, 839, 842

RADIO SHACK

828

RCA 837, 838, 839, 842

SAMSUNG 852

SKY+ 853

SKY HD 853

SONY 832, 835

TOSHIBA 833, 836

UNIDEN 825

ZENITH 834

YSP-3050

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY. LTD.

LEVEL 1, 99 QUEENSBRIDGE STREET, SOUTHBANK, VIC 3006, AUSTRALIA

Printed in Malaysia WK75600

YSP-3050

Digital Sound Projector

OWNER’S MANUAL

HDMI

OUTPUT

HDMI

OUT

DVD

STB

OUT

SUBWOOFER

VIDEO

HDMI

INPUT

Subwoofer

AUDIO INPUT VIDEO INPUT

OUT

AUX 1

TV/STB

SUBWOOFER

AUX 1

DVD

AUX 2

VIDEO

COMPONENT

STB

DVD

DIGITAL INPUT

COAXIAL

OPTICAL

ANALOG

AUDIO OUTPUT

VIDEO

INPUT

OPTICAL

DIGITAL OUTPUT

COAXIAL

DIGITAL OUTPUT

YSP-3050

QUICK REFERENCE GUIDE

Supplied accessories used for connections

and operations in this guide

Audio pin cable (x1)

OSD* video pin cable (x1)

Optical cable (x1)

Coaxial cable (x1)

Digital audio pin cable (x1)

IntelliBeam microphone (x1)

Cardboard microphone stand (x1)

Demonstration DVD (x1)

*OSD: On-Screen Display

This quick reference guide explains steps to connect a TV and a DVD player/recorder to this unit and achieve

the surround sound effects in a quick, easy manner. For detailed operation, refer to the Owner’s Manual.

Decide where to install this unit.

Install this unit where there are no objects such as furniture obstructing the path of sound beams. Otherwise, the desired surround sound effects may not be

achieved. You may install this unit in parallel with the wall or in the corner.

Install this unit using a rack, etc.

Depending on your installation environment, connections with external components (see “2 Connecting external components to this unit”) can be done before

installing this unit. We recommend that you temporarily place and arrange all components in order to decide which procedure must come first. In case you

install this unit on top of a rack, etc., use the supplied fasteners to prevent an accidental fall of this unit.

For further information on installation, see page 13 in the Owner’s Manual.

Installing this unit

Connecting external components such as a TV or DVD player/recorder to this unit.

Connect your TV or DVD player/recorder to this unit using appropriate cables as shown below.

For further information on connecting other components, see pages 16 to 23 in the Owner’s Manual.

Connecting external components to this unit

Install this unit in the exact center of the wall when it is

measured from the left and right corners.

The following is an example of installing this unit in a rack. To prevent this unit or the floor from being scratched, we recommend putting a piece of

cloth on the floor in step 2.

1 Place this unit in front of

the rack.

Place this unit upside down

and connect this unit to your

TV and DVD player/recorder.

3 Install this unit in the

rack.

Installation is completed.

Install this unit in the corner at a 40º to 50º angle from the

adjacent walls.

40º to 50º

An object, such as furniture An object, such as furniture

Front left channel

Center channel

Front right channel

Surround left channel

Surround right channel

Front left channel

Center channel

Front right channel

Surround left channel

Surround right channel

y Hint

Note

• To enjoy better surround effects, place this unit on the upper shelf to keep it away from the floor.

• You can also use the optional metal wall bracket (sold separately) to mount this unit on the wall. For details, refer to the instructions

supplied with the metal wall bracket.

Be careful not to leave scratches on this unit or the rack.

This connection example shows a way to connect external components such as a TV or DVD

player/recorder to this unit by using the supplied cable. You can enjoy the multi-channel audio from the

DVD player/recorder and the analog/digital audio from the TV. Use the video pin cable supplied with your

DVD player/recorder to make a video connection between your DVD player/recorder and TV.

Connection

example 1

Sold separately

1 HDMI cable

(Displays the DVD digital video and the YSP-3050 menu

screen on the TV)

2 HDMI cable

(Inputs the DVD digital audio/video signals to this unit)

Connect cables in the following order

Supplied

1 Audio pin cable

(Inputs the TV analog audio sounds to this unit)

2 OSD video pin cable

(Displays the YSP-3050 menu screen on the TV)

3 Optical cable

(Inputs the TV digital audio sounds to this unit)

4 Digital audio pin cable

(Inputs the DVD digital audio sounds to this unit)

Connect cables in the following order

Continued

on the back

If you have connected external components,

follow the steps on the backside to start the

AUTO SETUP procedure.

Note

Check whether the digital audio output of your TV and DVD

player/recorder is turned on.

y Hint

If you connect this unit to an HDMI control-compatible TV (except

some models) via HDMI, you can use the remote control supplied

with your TV to turn on or off the power, select the audio output

component, and adjust the volume level of this unit.

Note

Check whether the digital audio output of your TV and DVD

player/recorder is turned on.

This connection example shows a way to make the most of the capability of this unit. You can enjoy

DVD audio and video with higher quality via the HDMI cable. In case your TV does not have a built-in

digital satellite tuner, cable TV tuner, or digital airwave tuner, connect a digital satellite tuner, cable TV

tuner, or digital airwave tuner via the HDMI cable. For details, see “Connections using HDMI cables” on

page 18 and “Using the HDMI control feature” on page 73 in the Owner’s Manual.

Connection

example 2

Continued

on the back

If you have connected external components,

follow the steps on the backside to start the

AUTO SETUP procedure.

Digital satellite tuner/

Cable TV tuner/

Digital airwave tuner

1 (Sold separately)

DVD player/recorder

2 (Sold separately)

To the AC wall outlet

YSP-3050

Audio connection

HDMI connection

Subwoofer

Do not plug the power supply cable

into an AC wall outlet until all

connections are complete.

This connection is not

necessary if your TV has a

built-in digital satellite tuner,

cable TV tuner, or digital

airwave tuner. Use the optical

cable supplied with this unit to

make an audio connection

between your TV and this unit.

For details, see “Connection

example 1”.

123 4

To the AC wall outlet

YSP-3050

Audio connection

Video connection

Do not plug the power supply cable

into an AC wall outlet until all

connections are complete.

* The rear panel illustration shows jacks and their names to help you find them easily.

They are not exactly the same as the ones on the actual rear panel of this unit.

1. Pull out the cap

2. Check the direction

Optical cable

Pull out the cap

before connecting

the optical cable,

and then check

the direction to

insert the cable.

Subwoofer

* If TV built-in tuner is used, connect the

optical digital output jack on your TV to

the TV/STB OPTICAL DIGITAL INPUT

jack on this unit (see "Connecting a TV

without an HDMI cable" on page 21 in

the Owner's Manual).

Subwoofer

AUTO SETUP START

Will begin in 20sec

Please leave the room

**--------

[RETURN]:Cancel

AUTO SETUP

PREPARATION & CHECK

Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from the YSP

unit. The MIC should be set

at ear level when seated.

After [ENTER] is pressed,

please leave the room.

[ENTER]:Start [RETURN]:Cancel

Measurement takes about 3min.

SHOW RESULT

MEASUREMENT COMPLETE

BEAM MODE :5 BEAM

SUBWOOFER :NOT APPLICABLE

[ENTER]:Save set-up

[RETURN]:Do not save set-up

AUTO SETUP COMPLETE

Please remove the MIC from

the YSP and the listening

position.

INTELLIBEAM MIC

VOLUME

MIN

MAX

CROSSOVER/

HIGH CUT

MIN

MAX

INTELLIBEAM MIC

AUX1 AUX2 AUX3

DOCK

DVD

POWER POWERSTANDBY/ON

INPUT1 MACRO

TV/AV

YSP

ENTER

ENTRY

ENHANCER

DISPLAY RETURN

231

VOL MODE

AUTO

SETUP

INPUTMODE

SLEEP

5BEAM 3BEAMST+3BEAM

PRESET/TUNE

SEARCH MEMORY

TV/AV

YSP

ENTER

ENTRY

ENHANCER

DISPLAY RETURN

TV/AV

YSP

ENTER

ENTRY

ENHANCER

DISPLAY RETURN

TV/AV

YSP

ENTER

DISPLAY RETURN

TV/AV

YSP

ENTER

DISPLAY RETURN

AUX1 AUX2 AUX3

DVD

STB

INPUT1

PRESET/TUNE

SEARCH MEMORY

MACRO

231

VOL MODE

AUTO

SETUP

INPUTMODE

SLEEP

5BEAM 3BEAMST+3BEAM

STB

INPUT1

PRESET/TUNE

SEARCH MEMORY

MACRO

MUTE TV INPUT TV MUTE

VOLUME CH TV VOL

231

5BEAM

STEREO MY BEAM MY SUR.

3BEAMST+3BEAM

CAT/

A-E

CAT/

A-E

CAT/

A-E

CAT/

A-E

CAT/

A-E

CATFM/XM

Carry out the AUTO SETUP to adjust the settings that best match your listening

environment.

The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output

during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.

Enjoy TV or DVD digital audio in surround sound.

For instructions on how to operate or set your TV or DVD player/recorder, refer to the owner’s manual supplied with each component.

Assemble the cardboard microphone stand.

Place the IntelliBeam microphone on top of cardboard microphone stand as shown below.

Carry out the AUTO SETUP (IntelliBeam)

Enjoying surround sound

y Hint

Continued from the front

Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC jack

on the front panel.

Set the IntelliBeam microphone at your normal listening position.

Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would

be when you are seated.

Press STANDBY/ON on the remote control.

The power of this unit turns on.

Before operations, insert batteries into the remote

control (see page 24 in the Owner’s Manual).

If necessary, adjust the volume level of this unit.

If you have connected the subwoofer, set the

volume and crossover/high cut frequency. Refer

to the “Notes” on page 30 in the Owner’s Manual.

Set the operation mode selector to

YSP.

This unit switches to the YSP operation mode.

Press ENTER to start the AUTO

SETUP procedure, and then leave

the room within 10 seconds.

The following screen appears on the TV. Leave the room within

10 seconds before the AUTO SETUP procedure starts.

The setup screen automatically changes during the AUTO

SETUP procedure.

When the AUTO SETUP procedure is completed, the following

screen appears on the TV.

If “ENVIRONMENT CHECK (FAILED) is displayed, see page 34

in the Owner’s Manual and then run the procedure again.

• The result may differ depending on the environment.

• If any error occurs, the corresponding error message appears

on the screen. In this case, see “Error messages for AUTO

SETUP” on page 35 in the Owner’s Manual and then follow

the instructions. To start the AUTO SETUP procedure once

again, press RETURN.

Press and hold AUTO SETUP for

more than 2 seconds.

The menu screen appears on the TV.

If the menu screen does not appear, check the OSD video pin

cable (see the connection example on the front page).

Prepare to leave the room.

The best setting may not be done if you are in the room.

Prepare to leave the room in 10 seconds after pressing ENTER

in step 11.

• When leaving the room, bring this guide with you.

• Wait outside the room during the AUTO SETUP procedure.

• The AUTO SETUP procedure takes about 3 minutes.

• To cancel the AUTO SETUP procedure after it is started,

press RETURN.

Disconnect the IntelliBeam

microphone.

The AUTO SETUP has completed. Keep the IntelliBeam

microphone in a safe place.

The settings are automatically saved in the system memory.

Check the following points.

About the IntelliBeam microphone

• Is the microphone placed on an imaginary center line drawn

from this unit?

• Is the microphone placed within 1 m (3.3 ft) upper or lower

from the center height of this unit?

• Is the microphone placed more than 1.8 m (6.0 ft) from the

front of this unit?

About the room environment

• Is your listening room kept as quiet as possible?

Press ENTER.

The following screen appears on the TV for 2 seconds and then

the menu screen disappears from the TV.

Select the DVD video input on

your TV.

Check the digital signal being output at this unit.

The input channel indicators (see page 8 in the Owner’s Manual) are lit in the front panel display, and they

switch according to the channel composition of the corresponding input source. If the sound is output from your

TV speakers, mute the volume on your TV. For details about digital audio input signals, see page 58 in the

Owner’s Manual.

Press one of the beam mode buttons on the remote control to

select the desired beam mode.

Select one of the six beam modes that best matches the current input source of this unit.

For further information on the beam modes, see pages 56, 57, 62, 63 and 64 in the Owner’s Manual.

Press VOLUME +/- on the remote control to adjust the

volume level of this unit.

Select the TV channel using the

remote control supplied with your TV.

Mute the volume on the TV.

Set the operation mode selector to

YSP.

This unit switches to the YSP operation mode.

Set the operation mode selector to

YSP.

This unit switches to the YSP operation mode.

1) Press DVD on the remote

control of this unit.

This unit switches to the DVD playback mode.

Play back the supplied demonstration

DVD on the DVD player/recorder.

Press TV on the remote control of

this unit.

This unit switches to the TV playback mode.

Turn on the power of your TV.

Select the appropriate video input

on your TV.

If the OSD video pin cable is connected to the video input 1 on

the TV as shown in the connection example 1, switch the video

input to “1”.

IntelliBeam microphone (supplied)

Cardboard microphone stand (supplied)

12 43

Place the IntelliBeam microphone on the

extended center line of this unit and 1.8 m (6.0 ft)

or more away from it. Also, make sure place the

IntelliBeam microphone within 1 m (3.3 ft) upper

or lower from the center height of this unit.

IntelliBeam

microphone

Center height of

this unit

IntelliBeam

microphone

Cardboard

microphone stand

More than 1.8 m (6.0 ft)

Upper bound

position of the

microphone

Within 1 m (3.3 ft)

Listening

position

Lower bound position

of the microphone

Center line

Cardboard

microphone

stand

Enjoying DVDs in surround sound Enjoying TV in surround sound

Input channel indicators

To fine-tune the listening environment parameters manually or make advanced settings for speaker positions, sound

beams, etc., see “MANUAL SETUP” on page 74 in the Owner’s Manual.

Yamaha YSP-3050BL Handleiding

Merk: Yamaha

Model: YSP-3050BL

Categorie: Aanvullende muziekapparatuur

Type: Handleiding

Deze handleiding is ook geschikt voor

YSP-3050

Download PDF

rapport

in andere talen

English: Yamaha YSP-3050BL User manual
italiano: Yamaha YSP-3050BL Manuale utente
русский: Yamaha YSP-3050BL Руководство пользователя
français: Yamaha YSP-3050BL Manuel utilisateur
español: Yamaha YSP-3050BL Manual de usuario
Deutsch: Yamaha YSP-3050BL Benutzerhandbuch
português: Yamaha YSP-3050BL Manual do usuário
dansk: Yamaha YSP-3050BL Brugermanual
suomi: Yamaha YSP-3050BL Ohjekirja
čeština: Yamaha YSP-3050BL Uživatelský manuál
svenska: Yamaha YSP-3050BL Användarmanual
Türkçe: Yamaha YSP-3050BL Kullanım kılavuzu
polski: Yamaha YSP-3050BL Instrukcja obsługi
română: Yamaha YSP-3050BL Manual de utilizare

Yamaha YSP-3050BL Handleiding

Deze handleiding is ook geschikt voor

Yamaha YSP-3050BL Handleiding

in andere talen

Gerelateerde artikelen

Andere documenten