Yamaha DVD-S559 de handleiding

Categorie
Dvd spelers
Type
de handleiding
G
DVD-S559
DVD PLAYER
LECTEUR DE DVD
OWNER'S MANUAL
MODE D'EMPLOI
01_DVD-S559_En.book Page 0 Friday, November 18, 2005 4:32 PM
1
En
1
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2
Install this sound system in a well ventilated, cool,
dry, clean place — away from direct sunlight, heat
sources, vibration, dust, moisture, or cold. In a
cabinet, allow about 2.5 cm (1 inch) of free space
all around this unit for adequate ventilation.
3
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4
Do not expose this unit to sudden temperature
changes from cold to hot, nor locate this unit in
an environment with high humidity (i.e., a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5
Avoid installing this unit in a location where
foreign objects may fall onto this unit or where
this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Burning objects (i.e., candles), as they may
cause fire, damage to this unit, and/or personal
injury.
Containers with liquid in them, as they may fall,
spilling the liquid and causing an electrical
shock to the user and/or damage to this unit.
6
Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/or
personal injury.
7
Do not plug in this unit to a wall outlet until all
connections are complete.
8
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9
Do not use excessive force on switches, knobs
and/or cords.
10
When disconnecting the power cord from the
wall outlet, grasp the plug; do not pull the cord.
11
Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12
Use only the voltage specified on this unit. Using
this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from
use of this unit with a voltage other than as
specified.
13
To prevent damage by lightning, keep the power
cord out and outdoor antennas disconnected
from a wall outlet or the unit during a lightning
storm.
14
Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reason.
15
When not planning to use this unit for long
periods of time (i.e., vacation), disconnect the AC
power plug from the wall outlet.
16
Be sure to read the “Troubleshooting” section on
common operating errors before concluding that
this unit is faulty.
17
Before moving this unit, press STANDBY/ON to
set the unit in standby mode, then disconnect the
AC power plug from the wall outlet.
18
Install this unit near the AC outlet and where the
AC power plug can be reached easily.
LASER SAFETY
This unit employs a laser. Due to possible eye injury,
only a qualified service person should remove the
cover or attempt to service this device.
DANGER
This unit emits visible laser radiation when open.
Avoid direct eye exposure to beam.
When this unit is plugged into a wall outlet, do not
place your eyes close to the opening of the disc tray
and other openings or look inside.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
01_DVD-S559_En.book Page 1 Friday, November 18, 2005 4:32 PM
Contents
01
2
En
English
Thank you for purchasing this YAMAHA product.
Please read through this owner’s manual so that you will know how to operate your model
properly. After you have finished reading the instructions, put them in a safe place for future
reference
.
Contents
01 Before you start
Features
. . . . . . . . . . . . . . . . . . . . . . . . . . . 4
What’s in the box
. . . . . . . . . . . . . . . . . . . . 4
Hints on installation
. . . . . . . . . . . . . . . . . . 5
Disc/content format playback compatibility
5
02 Connecting up
Easy connections
. . . . . . . . . . . . . . . . . . . . 8
Connecting using a SCART AV cable
. . . . . 9
Connecting using the S-video output
. . . . . 9
Connecting using the component video
output
. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting to an AV receiver
. . . . . . . . . . 11
03 Controls and displays
Front panel
. . . . . . . . . . . . . . . . . . . . . . . . 12
Remote control
. . . . . . . . . . . . . . . . . . . . 13
04 Getting started
Switching on
. . . . . . . . . . . . . . . . . . . . . . 14
Using the on-screen displays
. . . . . . . . . . 14
Setting up the player for your TV
. . . . . . . . 15
Setting the language of this player’s
on-screen displays
. . . . . . . . . . . . . . . . . . 15
Playing discs
. . . . . . . . . . . . . . . . . . . . . . 16
05 Playing discs
Scanning discs
. . . . . . . . . . . . . . . . . . . . .20
Playing in slow motion
. . . . . . . . . . . . . . . .20
Frame advance/frame reverse
. . . . . . . . . .21
Viewing a JPEG slideshow
. . . . . . . . . . . . .21
Browsing DVD or Video CD/Super VCD disc
with the Disc Navigator
. . . . . . . . . . . . . . .21
Browsing WMA, MP3, DivX video and
JPEG files with the Disc Navigator
. . . . . . .22
Looping a section of a disc
. . . . . . . . . . . .23
Using repeat play
. . . . . . . . . . . . . . . . . . . .23
Using random play
. . . . . . . . . . . . . . . . . .24
Creating a program list
. . . . . . . . . . . . . . .25
Searching a disc
. . . . . . . . . . . . . . . . . . . .26
Switching subtitles
. . . . . . . . . . . . . . . . . .26
Switching audio language/channels
. . . . .27
Zooming the screen
. . . . . . . . . . . . . . . . . .27
Switching camera angles
. . . . . . . . . . . . .27
Displaying disc information
. . . . . . . . . . . .27
06 Audio Settings and Video Adjust
menus
Audio Settings menu
. . . . . . . . . . . . . . . . .28
Video Adjust menu
. . . . . . . . . . . . . . . . . .29
01_DVD-S559_En.book Page 2 Friday, November 18, 2005 4:32 PM
Contents01
3
En
07 Initial Settings menu
Using the Initial Settings menu
. . . . . . . . .30
Digital Audio Out settings
. . . . . . . . . . . . .30
Video Output settings
. . . . . . . . . . . . . . . .31
Language settings
. . . . . . . . . . . . . . . . . . .31
Display settings
. . . . . . . . . . . . . . . . . . . . .32
Options settings
. . . . . . . . . . . . . . . . . . . .32
Parental Lock
. . . . . . . . . . . . . . . . . . . . . . .33
08 Additional information
Taking care of your player and discs
. . . . .35
Screen sizes and disc formats
. . . . . . . . . .36
Setting the TV system
. . . . . . . . . . . . . . . .37
Resetting the player
. . . . . . . . . . . . . . . . . .37
DVD-Video regions
. . . . . . . . . . . . . . . . . . .37
Selecting languages using the language
code list
. . . . . . . . . . . . . . . . . . . . . . . . . . .37
Language code list
. . . . . . . . . . . . . . . . . . .38
Country/Area code list
. . . . . . . . . . . . . . . .38
Glossary
. . . . . . . . . . . . . . . . . . . . . . . . . . .39
Specifications
. . . . . . . . . . . . . . . . . . . . . .40
01_DVD-S559_En.book Page 3 Friday, November 18, 2005 4:32 PM
Before you start
01
4
En
English
Chapter 1
Before you start
Features
24-bit/192kHz compatible DAC
The on-board 24-bit/192kHz DAC means that
this player is fully compatible with high
sampling-rate discs, capable of delivering
exceptional sound quality in terms of dynamic
range, low-level resolution and high-frequency
detail.
Excellent audio performance surround
sound entertainment with Dolby Digital
*1
and DTS
*2
software
Logos:
When connected to a suitable AV amplifier or
receiver, this player gives great surround
sound with Dolby Digital and DTS discs.
PureCinema Progressive Scan video
When connected to a progressive scan-
compatible TV or monitor using the
component video outputs, you can enjoy
extremely stable, flicker free images, with the
same frame refresh rate as the original movie.
New Disc Navigator with moving
pictures
The new Disc Navigator enables you play the
first few seconds of each title or chapter in a
thumbnail image on screen.
DSP effects for enhanced playback
See Audio Settings and Video Adjust menus on
page 28.
Picture zoom
See Zooming the screen on page 27.
MP3 and WMA compatibility
See Compressed audio compatibility on page 6.
JPEG compatibility
See JPEG file compatibility on page 7.
DivX video compatibility
See DivX video compatibility on page 7.
Energy saving design
An auto power-off function switches the player
into standby if not used for about 30 minutes.
*1
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
*2
“DTS” and “DTS Digital Out” are registered
trademarks of Digital Theater Systems Inc.
What’s in the box
Please confirm that the following accessories
are in the box when you open it.
Remote control
AA/R6 dry cell batteries x2
Audio/video cable (red/white/yellow plugs)
Power cable
Owner’s Manual
Putting the batteries in the remote
Open the battery compartment cover
and insert the batteries as shown.
Use two AA/R6 batteries and follow the
indications (, ) inside the compartment.
Close the cover when you’re finished.
01_DVD-S559_En.book Page 4 Friday, November 18, 2005 4:32 PM
Before you start01
5
En
Important
Incorrect use of batteries can result in hazards
such as leakage and bursting. Please observe
the following:
Don’t mix new and old batteries together.
Don’t use different kinds of battery
together—although they may look similar,
different batteries may have different
voltages.
Make sure that the plus and minus ends of
each battery match the indications in the
battery compartment.
Remove batteries from equipment that
isn’t going to be used for a month or more.
When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country or area.
Hints on installation
We want you to enjoy using this product for
years to come, so please use the following
guidelines when choosing a suitable location:
Do...
Use in a well-ventilated room.
Place on a solid, flat, level surface, such as
a table, shelf or stereo rack.
Don’t...
Use in a place exposed to high
temperatures or humidity, including near
radiators and other heat-generating
appliances.
Place on a window sill or a place where the
player will be exposed to direct sunlight.
Use in an excessively dusty or damp
environment.
Place directly on top of an amplifier, or
other component in your stereo system
that becomes hot in use.
Use near a television or monitor as you may
experience interference—especially if the
television uses an indoor antenna.
Use in a kitchen or other room where the
player may be exposed to smoke or steam.
Use on a thick rug or carpet, or cover with
cloth—this may prevent proper cooling of
the unit.
Place on an unstable surface, or one that is
not large enough to support all four of the
unit’s feet.
Disc/content format playback
compatibility
This player is compatible with a wide range of
disc types (media) and formats. Playable discs
will generally feature one of the following logos
on the disc and/or disc packaging. Note
however that some disc types, such as
recordable CD and DVD, may be in an
unplayable format—see below for further
compatibility information.
Please also note that recordable discs cannot be
recorded using this player.
is a trademark of Fuji Photo Film Co. Ltd.
Also compatible with KODAK Picture CD
DVD-Video DVD-R DVD-RW
DVD+Rewritable DVD+R DVD+RDL
Video CD
Fujicolor CD
Audio CD CD-R CD-RW
DVD+R DL
DVD+R
DVD+ReWritable
01_DVD-S559_En.book Page 5 Friday, November 18, 2005 4:32 PM
Before you start
01
6
En
English
This player supports the IEC’s Super VCD stan-
dard. Compared to the Video CD standard,
Super VCD offers superior picture quality, and
allows two stereo soundtracks to be recorded.
Super VCD also supports the widescreen size.
CD-R/RW compatibility
Compatible formats: CD-Audio, Video CD/
Super VCD, ISO 9660 CD-ROM* containing
MP3, WMA, JPEG or DivX video files
* ISO 9660 Level 1 or 2 compliant. CD
physical format: Mode1, Mode2 XA Form1.
Romeo and Joliet file systems are both
compatible with this player.
Multi-session playback: No
Unfinalized disc playback: No
File structure (may differ): Up to 299 folders
on a disc; up to 648 folders and files
(combined) within each folder
DVD+R/RW, DVD-R/RWcompatibility
Compatible formats: DVD-Video, Video
Recording (VR)*
* DVD-RW only. Edit points may not play
exactly as edited; screen may go
momentarily blank at edited points.
Unfinalized playback: No
WMA/MP3/JPEG file playback on DVD+R/
RW, DVD-R/RW: No
Compressed audio compatibility
Compatible formats: MPEG-1 Audio Layer 3
(MP3), Windows Media Audio (WMA)
Sampling rates: 32, 44.1 or 48kHz
Bit-rates: Any (128Kbps or higher
recommended)
VBR (variable bit rate) MP3 playback: No
VBR WMA playback: No
WMA lossless encoding compatible: No
DRM (Digital Rights Management)
compatible: Yes (DRM-protected audio
files will not play in this player—see also
DRM in the Glossary on page 39)
File extensions: .mp3, .wma (these must be
used for the player to recognize MP3 and
WMA files – do not use for other file types)
About WMA
The Windows Media
®
logo indicates that this
player can playback Windows Media Audio
content.
WMA is an acronym for Windows Media Audio
and refers to an audio compression technology
developed by Microsoft Corporation. WMA
content can be encoded by using Windows
Media
®
Player version 7, 7.1, Windows Media
®
Player for Windows
®
XP, or Windows Media
®
Player 9 Series.
Microsoft, Windows Media, and the Windows
logo are trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
About DivX
DivX is a compressed digital video format
created by the DivX
®
video codec from
DivXNetworks, Inc. This player can play DivX
video files burned on CD-R/RW/ROM discs.
Keeping the same terminology as DVD-Video,
individual DivX video files are called "Titles".
When naming files/titles on a CD-R/RW disc
prior to burning, keep in mind that by default
they will be played in alphabetical order.
Super VCD
01_DVD-S559_En.book Page 6 Friday, November 18, 2005 4:32 PM
Before you start01
7
En
Displaying DivX subtitle files
The font sets listed below are available for DivX
external subtitle files. You can see the proper
font set on-screen by setting the Subtitle
Language (in Language settings on page 31)
to match the subtitle file.
This player supports the following language
groups:
Group 1: Albanian (sq), Basque (eu), Catalan (ca),
Danish (da), Dutch (nl), English (en), Faroese (fo),
Finnish (fi), French (fr), German (de), Icelandic (is), Irish
(ga), Italian (it), Norwegian (no), Portuguese (pt), Rhaeto-
Romanic (rm), Scottish (gd), Spanish (es), Swedish (sv)
Group 2: Albanian (sq), Croatian (hr), Czech (cs),
Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk),
Slovenian (sl)
Group 3: Bulgarian (bg), Byelorussian (be), Macedonian
(mk), Russian (ru), Serbian (sr), Ukrainian (uk)
Group 4: Hebrew (iw), Yiddish (ji)
Group 5: Turkish (tr)
DivX, DivX Certified, and associated logos are
trademarks of DivXNetworks, Inc. and are used
under license.
Some external subtitle files may be
displayed incorrectly or not at all.
For external subtitle files the following
subtitle format filename extensions are
supported (please note that these files are
not shown within the disc navigation
menu): .srt, .sub, .ssa, .smi
The filename of the movie file has to be
repeated at the beginning of the filename
for the external subtitle file.
The number of external subtitle files which
can be switched for the same movie file is
limited to a maximum of 10.
DivX video compatibility
Official DivX
®
Certified product.
Plays DivX
®
5, DivX
®
4, DivX
®
3 and DivX
®
VOD video content (in compliance with
DivX
®
Certified technical requirements).
File extensions: .avi and .divx (these must
be used for the player to recognize DivX
video files). Note that all files with the .avi
extension are recognized as MPEG4, but not
all of these are necessarily DivX video files
and therefore may not be playable on this
player.
DivX, DivX Certified, and associated logos are
trademarks of DivXNetworks, Inc. and are used
under license.
JPEG file compatibility
Compatible formats: Baseline JPEG and
EXIF 2.2* still image files up to a resolution
of 3072 x 2048.
*File format used by digital still cameras
Progressive JPEG compatible: No
File extensions: .jpg (must be used for the
player to recognize JPEG files – do not use
for other file types)
PC-created disc compatibility
Discs recorded using a personal computer
may not be playable in this unit due to the
setting of the application software used to
create the disc. In these particular instances,
check with the software publisher for more
detailed information.
Discs recorded in packet write mode (UDF
format) are not compatible with this player.
Check the DVD+R/RW, DVD-R/RW or CD-R/
RW software disc boxes for additional
compatibility information.
01_DVD-S559_En.book Page 7 Friday, November 18, 2005 4:32 PM
Connecting up
02
8
En
English
Chapter 2
Connecting up
Easy connections
The setup described here is a basic setup that allows you to play discs using just the cables
supplied with the player. In this setup, stereo audio is played through the speakers in your TV.
Important
This player is equipped with copy protection technology. Do not connect this player to your TV
via a VCR using audio/video or S-video cables, as the picture from this player will not appear
properly on your TV. (This player may also not be compatible with some combination TV/VCRs
for the same reason; refer to the manufacturer for more information.)
To power
outlet
DIGITAL OUT VIDEO OUT
S VIDEO
P
R
/C
R
Y
P
B
/C
B
COAXIAL
PCM/q DIGITAL
/DTS/MPEG
COMPONENT
VIDEO
AUDIO OUT
AV
L
R
AC IN
Yellow
White
Red
TV
A/V IN
01_DVD-S559_En.book Page 8 Friday, November 18, 2005 4:32 PM
Connecting up02
9
En
1 Connect the VIDEO OUT and AUDIO
OUT L/R jacks to a set of A/V inputs on your
TV.
Use the supplied audio/video cable,
connecting the red and white plugs to the
audio outputs and the yellow plug to the video
output. Make sure you match up the left and
right audio outputs with their corresponding
inputs for correct stereo sound.
See below if you want to use a component or
S-video cable for the video connection.
2 Connect the supplied AC power cable to
the AC IN inlet, then plug into a power
outlet.
Note
Before unplugging the player from the
power outlet, make sure you first switch it
into standby using either the front panel
STANDBY/ON button, or the remote
control, and wait of the -OFF- message to
disappear from the player’s display.
For the above reasons, do not plug this
player into a switched power supply found
on some amplifiers and AV receivers.
Connecting using a SCART AV
cable
A SCART-type AV connector is provided for
connection to a TV or AV receiver. The video
output is switchable between ordinary
composite and RGB. See AV Connector Out on
page 31 for how to set it.
The SCART AV connector also outputs analog
audio, so there is no need to also connect the
AUDIO OUT L/R jacks.
1 Use a SCART cable (not supplied) to
connect the AV CONNECTOR (RGB) output
to a SCART AV input on your TV (or AV
receiver).
Connecting using the S-video
output
If your TV (or other equipment) has an S-video
(S1) input, you can use the S-video output on
this player instead of the standard (composite)
output for a better quality picture.
Use an S-video cable (not supplied) to
connect the S-VIDEO OUT to an S-video
input on your TV (or monitor or AV
receiver).
Line up the small triangle above the jack with
the same mark on the plug before plugging in.
U
T
Y
COMPONENT
VIDEO
AUDIO OUT
AV
L
R
TV
SCART
01_DVD-S559_En.book Page 9 Friday, November 18, 2005 4:32 PM
Connecting up
02
10
En
English
Connecting using the
component video output
You can use the component video output
instead of the standard video out jack to
connect this player to your TV (or other
equipment). This should give you the best
quality picture from the three types of video
output available.
Use a component video cable (not
supplied) to connect the COMPONENT
VIDEO OUT jacks to a component video
input on your TV, monitor or AV receiver.
Watching progressive scan video
from the component video outputs
This player can output progressive scan video
from the component video output. Compared
to interlace video, progressive scan video
effectively doubles the scanning rate of the
picture, resulting in a very stable, flicker-free
image.
To set up the player for use with a progressive
scan TV, see Video Output settings on page 31.
When the player is set to output progressive
scan video, the PRGSVE indicator lights in the
front panel display.
Important
If you connect a TV that is not compatible
with a progressive scan signal and switch
the player to progressive, you will not be
able to see any picture at all. In this case,
switch everything off and reconnect using
the supplied video cable (see Easy
connections on page 8), then switch back
to Interlace (see below).
Switching the video output to interlace
using the front panel controls
Switch the player to standby then, using the
front panel controls, press STANDBY/ON
while pressing to switch the player back to
Interlace.
DIGITAL OUT VIDEO OUT
S VIDEO
P
R
/C
R
Y
P
B
/C
B
COAXIAL
PCM/q DIGITAL
/DTS/MPEG
COMPONENT
VIDEO
AUDIO OUT
L
R
TV
S-VIDEO
IN
DIGITAL OUT VIDEO OUT
S VIDEO
P
R
/C
R
Y
P
B
/C
B
COAXIAL
PCM/q DIGITAL
/DTS/MPEG
COMPONENT
VIDEO
AUDIO OUT
L
R
TV
COMPONENT
VIDEO IN
STANDBY/ON
DVD-S559
01_DVD-S559_En.book Page 10 Friday, November 18, 2005 4:32 PM
Connecting up02
11
En
Compatibility of this player with
progressive-scan and high-definition TVs
This player is compatible with progressive
video Macro Vision System Copy Guard.
Consumers should note that not all high-
definition television sets are fully compatible
with this product and may cause artifacts to be
displayed in the picture. In case of 525/625
progressive scan picture problems, it is
recommended that the user switch the
connection to the ‘standard definition’ output
(Interlace). If there are questions regarding our
TV set compatibility with this model, please
contact our customer service center.
This player is fully compatible with the
complete line of YAMAHA products, including
the projectors DPX-1200, LPX-510 and the
plasma monitor PDM-4220.
Connecting to an AV receiver
To enjoy multichannel surround sound you
need to connect this player to an AV receiver
using the digital audio output.
In addition to a digital connection, we
recommend also connecting using the stereo
analog connection.
You’ll probably also want to connect a video
output to your AV receiver. You can use any of
the video outputs available on this player (the
illustration shows a standard (composite)
connection).
1 Connect the DIGITAL AUDIO OUT
COAXIAL jack on this player to a coaxial
digital input on your AV receiver.
Use a coaxial cable (similar to the supplied
video cable) to connect the COAXIAL DIGITAL
AUDIO OUT jack to a coaxial input on your AV
receiver.
2 Connect the analog AUDIO OUT L/R and
VIDEO OUT jacks on this player to a set of
analog audio and video inputs on your AV
receiver.
You can use the SCART AV connector, or
the S-video or component video jacks to
connect to the AV receiver if you prefer.
DIGITAL OUT VIDEO OUT
S VIDEO
P
R
/C
R
Y
P
B
/C
B
COAXIAL
PCM/q DIGITAL
/DTS/MPEG
COMPONENT
VIDEO
AUDIO OUT
L
R
AV receiver
DIGITAL IN
(COAXIAL)
AV receiver
DIGITAL OUT VIDEO OUT
S VIDEO
P
R
/C
R
Y
P
B
/C
B
COAXIAL
PCM/q DIGITAL
/DTS/MPEG
COMPONENT
VIDEO
AUDIO OUT
L
R
AUDIO/
VIDEO IN
01_DVD-S559_En.book Page 11 Friday, November 18, 2005 4:32 PM
Controls and displays
03
12
En
English
Chapter 3
Controls and displays
Front panel
1 STANDBY/ON (page 14)
2 Disc tray
3 (page 17)
4 (page 17)
5 and (page 17)
6 (page 16)
7 Display
8 (page 17)
DVD-S559
1
2
5
3 4
6 7
8
01_DVD-S559_En.book Page 12 Friday, November 18, 2005 4:32 PM
Controls and displays03
13
En
Remote control
1(STANDBY/ON) (page 14)
2 Number buttons (page 17)
3 PLAY MODE (page 23)
4 SURROUND (page 28)
5 TOP MENU (page 18)
6 ENTER & cursor buttons (page 14)
7 HOME MENU (page 14)
8 SUBTITLE (page 26)
9 ANGLE (page 27)
10 and (SKIP) (page 17)
11 (STOP) (page 17)
12 OPEN/CLOSE (page 16)
13 ENTER (page 14)
14 CLEAR (page 25)
15 ON SCREEN (page 27)
16 MENU (page 18)
17 RETURN (page 14)
18 AUDIO (page 27)
19 ZOOM (page 27)
20 and (SLOW/SEARCH)
(page 17, 20
)
21 (PLAY) (page 17)
22 (PAUSE) (page 17)
Using the remote control
Keep in mind the following when using the
remote control:
Make sure that there are no obstacles
between the remote and the remote sensor
on the unit.
The remote has a range of about 7m.
Remote operation may become unreliable
if strong sunlight or fluorescent light is
shining on the unit’s remote sensor.
Remote controllers for different devices
can interfere with each other. Avoid using
remotes for other equipment located close
to this unit.
Replace the batteries when you notice a
fall off in the operating range of the remote.
5
2
4
9
10
7
6
8
11
1
3
12
13
15
16
17
18
21
22
14
19
20
STANDBY/ON
STANDBY/ON
CLEAR
CLEAR
OPEN/CLOSE
OPEN/CLOSE
ENTER
ENTER
PLAY MODE
PLAY MODE
SURROUND
SURROUND
ON SCREEN
ON SCREEN
MENU
MENU
TOP MEN
TOP MENU
SUBTITLE
SUBTITLE
HOME
HOME
MENU
MENU
RETURN
RETURN
ANGLE
ANGLE
ZOOM
ZOOM
AUDIO
AUDIO
SKIP
SKIP
SLOW/SEARCH
SLOW/SEARCH
STOP
STOP
PAUSE
PAUSE
PLAY
PLAY
ENTER
ENTER
21
5
9
3
7
4
8
6
0
01_DVD-S559_En.book Page 13 Friday, November 18, 2005 4:32 PM
Getting started
04
14
En
English
Chapter 4
Getting started
Switching on
After making sure that everything is connected
properly and that the player is plugged in,
press STANDBY/ON on the front panel or
remote control to switch the player on.
Also, switch on your TV and make sure that it is
set to the input you connected the DVD player
to.
FAQ
My DVD player switches on but there is
nothing displayed on my TV.
Make sure that the TV is set to the correct
video input (not a TV channel). For
example, if you connected this player to the
VIDEO 1 inputs on your TV, switch your TV
to VIDEO 1.
Note
This player features a screen saver and an
auto power off function. If the player is
stopped and no button is pressed for
around five minutes, the screen saver
starts. If the disc tray is closed but no disc
is playing and no control is pressed for
about 30 minutes, the player automatically
goes into standby.
Using the on-screen displays
For ease of use, this player makes extensive
use of graphical on-screen displays (OSDs).
All the screens are navigated in basically the
same way, using the cursor buttons
() to change the highlighted item and
pressing ENTER to select it.
Note
From here on in this manual, the word
‘select’ generally means use the cursor
buttons to highlight an item on-screen,
then press ENTER.
STANDBY/ON
DVD-S559
Button What it does
HOME
MENU
Display/exit the on-screen display.
Changes the highlighted menu
item.
ENTER
Selects the highlighted menu
item (both
ENTER buttons on the
remote work in exactly the same
way).
RETURN Returns to the main menu
without saving changes.
STANDBY/ON
CLEAR
CLEAR
OPEN/CLOSE
ENTER
ENTER
PLAY MODE
PLAY MODE
SURROUND
SURROUND
ON SCREEN
ON SCREEN
MENU
MENU
TOP MEN
TOP MENU
SUBTITLE
SUBTITLE
HOME
HOME
MENU
MENU
RETURN
RETURN
ANGLE
ANGLE
ZOOM
ZOOM
AUDIO
AUDIO
SKIPSKIP SLOW/SEARCHSLOW/SEARCH
STOP PAUSE PLAY
ENTER
ENTER
5
9
78
6
0
01_DVD-S559_En.book Page 14 Friday, November 18, 2005 4:32 PM
Getting started04
15
En
Setting up the player for your
TV
If you have a widescreen (16:9) TV, you should
setup the player so that the picture will be
presented correctly. If you have a conventional
(4:3) TV, you can leave the player on the default
setting and move on to the next section.
1 Press HOME MENU and select ‘Initial
Settings’.
2 Select ‘TV Screen’ from the ‘Video
Output’ settings.
3 If you have a widescreen (16:9) TV,
select ‘16:9 (Wide)’.
If you have a conventional (4:3) TV, you can
change the setting from 4:3 (Letter Box) to 4:3
(Pan & Scan) if you prefer. See Video Output
settings on page 31 for more details.
4 Press HOME MENU to exit the menu
screen.
Setting the language of this
player’s on-screen displays
This sets the language of the player’s on-
screen displays.
1 Press HOME MENU and select ‘Initial
Settings’.
2 Select ‘OSD Language’ from the
‘Display’ settings.
3 Select a language.
The on-screen language will change according
to your selection.
4 Press HOME MENU to exit the menu
screen.
Initial Settings
Digital Audio Out
Video Outpu
t
Language
Display
Options
TV Screen
Component Out
AV Connector Out
4:3 (Letter Box)
4:3 (Pan&Scan)
16:9 (Wide)
Initial Settings
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
OSD Language
Angle Indicator
English
français
Deutsch
Italiano
Español
Initial Settings
01_DVD-S559_En.book Page 15 Friday, November 18, 2005 4:32 PM
Getting started
04
16
En
English
Playing discs
The basic playback controls for playing DVD,
CD, Video CD/Super VCD, DivX video and MP3/
WMA discs are covered here. Further functions
are detailed in the next chapter.
For details on playing JPEG picture discs, see
Viewing a JPEG slideshow on page 21.
Important
Throughout this manual, the term ‘DVD’
means DVD-Video, DVD+R/RW and DVD-
R/RW. If a function is specific to a
particular kind of DVD disc, it is specified.
1 If the player isn’t already on, press
(STANDBY/ON) to switch it on.
If you’re playing a DVD, disc containing DivX
video files or Video CD/Super VCD, also turn on
your TV and make sure that it is set to the
correct video input.
2 Press OPEN/CLOSE () to open the disc
tray.
3 Load a disc.
Load a disc with the label side facing up, using
the disc tray guide to align the disc (if you’re
loading a double-sided DVD disc, load it with
the side you want to play face down).
4 Press (play) to start playback.
If you’re playing a DVD or Video CD/Super VCD,
an on-screen menu may appear. See DVD-
Video disc menus on page 18 and Video CD/
Super VCD PBC menus on page 18 for more on
how to navigate these.
If you’re playing a containing DivX video
files or MP3/WMA audio files, it may take a
few seconds before playback starts, etc.
This is normal.
Note
You may find with some DVD discs that
some playback controls don’t work in
certain parts of the disc. This is not a
malfunction.
If a disc contains a mixture of DivX video
and other media file types (MP3, for
example), first select whether to play the
DivX video files (DivX)or the other media
file types (MP3 / WMA / JPEG) from the
on-screen display.
STANDBY/ON
CLEAR
OPEN/CLOSE
ENTER
PLAY MODE
SURROUND
ON SCREEN
MENU
TOP MEN
SUBTITLE
HOME
MENU
RETURN
ANGLE
ZOOM
AUDIO
SKIP
SLOW/SEARCH
STOP
PAUS E
PLAY
ENTER
21
5
9
3
7
4
8
6
0
01_DVD-S559_En.book Page 16 Friday, November 18, 2005 4:32 PM
Getting started04
17
En
Basic playback controls
The table below shows the basic controls on
the remote for playing discs. The following
chapter covers other playback features in more
detail.
Resume and Last Memory
When you stop playback of a DVD, CD, Video
CD/Super VCD or DivX video discs, RESUME is
shown in the display indicating that you can
resume playback again from that point.
If the disc tray is not opened, the next time you
start playback the display shows RESUME and
playback resumes from the resume point. (If
you want to clear the resume point, press
(stop) while RESUME is displayed.)
With DVDs and Video CD/ Super VCDs, if you
take the disc out of the player after stopping
playback, the last play position is stored in
memory. If the next disc you load is the same
one, the display shows LAST MEM and
playback will resume. For DVD-Video discs, the
player stores the play position of the last five
discs. When one of these discs is next loaded,
you can resume playback.
Note
The Last Memory function doesn’t work
with VR format DVD-RW discs.
If you don’t need the Last Memory function
when you stop a disc, you can press OPEN/
CLOSE () to stop playback and open the
disc tray.
Button What it does
Starts playback.
If the display shows RESUME or
LAST MEM playback starts from the
resume or last memory point (see
also Resume and Last Memory
below.)
Pauses a disc that’s playing, or
restarts a paused disc.
Stops playback.
See also Resume and Last Memory
below.
(remote
only)
Press to start fast reverse scanning.
Press
(play) to resume normal
playback.
(remote
only)
Press to start fast forward scanning.
Press (play) to resume normal
playback.
Skips to the start of the current
track, title or chapter, then to
previous tracks/titles/chapters.
Skips to the next track, title or
chapter.
Numbers
(remote
only)
Use to enter a title/chapter/track
number. Press
ENTER to select.
• If the disc is stopped, playback
starts from the selected title (for
DVD) or track (for CD/Video CD
/
Super VCD
).
• If the disc is playing, playback
jumps to the start of the selected
title (VR mode DVD-RW), chapter
(DVD-Video) or track (CD/Video CD/
Super VCD).
01_DVD-S559_En.book Page 17 Friday, November 18, 2005 4:32 PM
Getting started
04
18
En
English
DVD-Video disc menus
Many DVD-Video discs feature menus from
which you can select what you want to watch.
They may also give access to additional
features, such as subtitle and audio language
selection, or special features such as
slideshows. See the disc packaging for details.
Sometimes DVD-Video menus are displayed
automatically when you start playback; others
only appear when you press MENU or TOP
MENU.
Video CD/Super VCD PBC menus
Some Video CD/Super VCDs have menus from
which you can choose what you want to watch.
These are called PBC (Playback control)
menus.
You can play a PBC Video CD/Super VCD
without having to navigate the PBC menu by
starting playback using a number button to
select a track, rather than the (play) button.
Button What it does
TOP MENU Displays the ‘top menu’ of a DVD
disc—this varies with the disc.
MENU Displays a DVD disc menu—this
varies with the disc and may be
the same as the ‘top menu’.
Moves the cursor around the
screen.
ENTER Selects the current menu option.
RETURN Returns to the previously dis-
played menu screen.
Numbers
(remote
only)
Highlights a numbered menu
option (some discs only). Press
ENTER to select.
STANDBY/ON
CLEAR
CLEAR
OPEN/CLOSE
ENTER
ENTER
PLAY MODE
PLAY MODE
SURROUND
SURROUND
ON SCREEN
ON SCREEN
MENU
MENU
TOP MEN
TOP MENU
SUBTITLE
SUBTITLE
HOME
HOME
MENU
MENU
RETURN
RETURN
ANGLE
ANGLE
ZOOM
ZOOM
AUDIO
AUDIO
SKIP SLOW/SEARCH
STOP PAUSE PLAY
ENTER
ENTER
21
5
9
3
7
4
8
6
0
Button What it does
RETURN Displays the PBC menu.
Numbers
(remote
only)
Use to enter a numbered menu
option. Press
ENTER to select.
Displays the previous menu page
(if there is one).
Displays the next menu page (if
there is one).
STANDBY/ON
CLEARCLEAR
OPEN/CLOSE
ENTERENTER
PLAY MODEPLAY MODE SURROUNDSURROUND ON SCREENON SCREEN
MENUMENU
TOP MENTOP MENU
SUBTITLESUBTITLE
HOMEHOME
MENUMENU
RETURNRETURN
ANGLEANGLE ZOOMZOOM AUDIOAUDIO
SKIPSKIP SLOW/SEARCHSLOW/SEARCH
STOPSTOP PAUSEPAUSE PLAYPLAY
ENTERENTER
21
5
9
3
7
4
8
6
0
01_DVD-S559_En.book Page 18 Friday, November 18, 2005 4:32 PM
Getting started04
19
En
FAQ
After I load a DVD disc, it ejects
automatically after a few seconds!
Most likely, the disc is the wrong region for
your player. The region number should be
printed on the disc; check it against the
region number of the player (which you can
find on the rear panel). See also DVD-Video
regions on page 37.
If the region number is OK, it may be that
the disc is damaged or dirty. Clean the disc
and look for signs of damage. See also
Taking care of your player and discs on
page 35.
Why won’t the disc I loaded play?
First check that you loaded the disc the
right way up (label side up), and that it’s
clean and undamaged. See Taking care of
your player and discs on page 35 for
information on cleaning discs.
If a disc loaded correctly won’t play, it’s
probably an incompatible format or disc
type, such as DVD-Audio or DVD-ROM. See
Disc/content format playback compatibility
on page 5 for more on disc compatibility.
•I have a widescreen TV so why are there
black bars at the top and bottom of the
screen when I play some discs?
Some movie formats are such that even
when played on a widescreen TV, black
bars are necessary at the top and bottom of
the screen. This is not a malfunction.
•I have a standard (4:3) TV and set the player
to show widescreen DVDs in pan & scan
format, so why do I still get black bars top
and bottom with some discs?
Some discs override the display
preferences of the player, so even if you
have 4:3 (Pan & Scan) selected, those
discs will still be shown in letter box format.
This is not a malfunction.
01_DVD-S559_En.book Page 19 Friday, November 18, 2005 4:32 PM
Playing discs
05
20
En
English
Chapter 5
Playing discs
Note
Many of the functions covered in this
chapter apply to DVD discs, Video CDs/
Super VCDs, CDs, DivX video and WMA/
MP3 JPEG discs, although the exact
operation of some varies slightly with the
kind of disc loaded.
Some DVDs restrict the use of some
functions (random or repeat, for example)
in some or all parts of the disc. This is not a
malfunction.
When playing Video CD/Super VCDs, some
of the functions are not available during
PBC playback. If you want to use them,
start the disc playing using a number
button to select a track.
Scanning discs
You can fast-scan discs forward or backward at
four different speeds (DivX video only one
speed).
1 During playback, press or to
start scanning.
There is no sound while scanning DVDs,
DivX video and Video CD/Super VCDs.
2 Press repeatedly to increase the
scanning speed.
The scanning speed is shown on-screen
except when playing a WMA/MP3 track
using
the Disc Navigator.
3 To resume normal playback, press
(play).
When scanning a Video CD/Super VCD
playing in PBC mode or a WMA/MP3 track,
playback automatically resumes at the end
or beginning of the track.
Depending on the disc, normal playback
may automatically resume when a new
chapter is reached on a DVD disc.
Playing in slow motion
You can play DVDs at four different slow
motion speeds, forwards and backwards.
Video CD/Super VCDs and DivX video can be
played at four different forward slow motion
speeds.
1 During playback, press (pause).
2 Press and hold or until slow
motion playback starts.
The slow motion speed is shown on-
screen.
There is no sound during slow motion
playback.
3 Press repeatedly to change the slow
motion speed.
4 To resume normal playback, press
(play).
Depending on the disc, normal playback
may automatically resume when a new
chapter is reached.
01_DVD-S559_En.book Page 20 Friday, November 18, 2005 4:32 PM
Playing discs05
21
En
Frame advance/frame reverse
You can advance or back up DVD discs frame-
by-frame. With Video CD/Super VCDs and DivX
video file you can only use frame advance.
1 During playback, press (pause).
2 Press or to reverse or advance
a frame at a time.
3 To resume normal playback, press
(play).
Depending on the disc, normal playback
may automatically resume when a new
chapter is reached.
Viewing a JPEG slideshow
After loading a CD/CD-R/RW containing JPEG
picture files, press (play) to start a slideshow
from the first folder/picture on the disc. The
player displays the pictures in each folder in
alphabetical order.
Pictures are automatically adjusted so that
they fill as much of the screen as possible (if
the aspect ratio of the picture is different to
your TV screen you may notice black bars at the
sides, or at the top and bottom of the screen).
While the slideshow is running:
Note
The time it takes for the player to load a file
increases with large file sizes.
Browsing DVD or Video CD/
Super VCD disc with the Disc
Navigator
Use the Disc Navigator to browse through the
contents of a DVD or Video CD/Super VCD disc
to find the part you want to play.
Important
You can’t use the Disc Navigator with
Video CD/Super VCDs in PBC mode.
1 During playback, press HOME MENU
and select ‘Disc Navigator’ from the on-
screen menu.
2 Select a view option.
Button What it does
Pauses the slideshow; press again to
restart.
Displays the previous picture.
Displays the next picture.
Pauses the slideshow and rotates the
displayed picture 90º (counter)
clockwise. (Press (play) to restart
slideshow).
Pauses the slideshow and flips the
displayed picture horizontally or
vertically. (Press (play) to restart
slideshow).
ZOOM Pauses the slideshow and zooms the
picture. Press again to toggle
between 1x, 2x and 4x zoom. (Press
(play) to restart slideshow).
MENU Displays the Disc Navigator screen
(see below).
Button What it does
Disc Navigator
Disc Navigator
Title
Chapter
01_DVD-S559_En.book Page 21 Friday, November 18, 2005 4:32 PM
Playing discs
05
22
En
English
The options available depend on the kind of
disc loaded and whether the disc is playing or
not, but include:
Title – Titles from a DVD-Video disc.
Chapter – Chapters from the current title
of a DVD-Video disc.
Track – Tracks from a Video CD/Super VCD
disc.
Time – Thumbnails from a Video CD/Super
VCD disc at 10 minute intervals.
Original: Title – Original titles from a VR
mode DVD-RW disc.
Playlist: Title – Playlist titles from a VR
mode DVD-RW disc.
Original: Time – Thumbnails from the
Original content at 10 minute intervals.
Playlist: Time – Thumbnails from the
Playlist at 10 minute intervals.
The screen shows up to six moving thumbnail
images displayed one after another. To display
the previous/next six thumbnails, press /
(you don’t have to wait for all the
thumbnails to finish playing to display the
previous/next page).
3 Select the thumbnail image for what
you want to play.
You can use either the cursor buttons
() and ENTER to select a thumbnail,
or the number buttons.
To select using the number buttons, enter a
two-digit number then press ENTER.
Tip
Another way to find a particular place on a
disc is to use one of the search modes. See
Searching a disc on page 26.
Browsing WMA, MP3, DivX
video and JPEG files with the
Disc Navigator
Use the Disc Navigator to find a particular file
or folder by filename. Note that if there are
other types of files on the same disc, these will
not be displayed in the Disc Navigator.
1 Press HOME MENU and select ‘Disc
Navigator’ from the on-screen menu.
2 Use the cursor buttons ( ) and
ENTER to navigate.
Use the cursor up/down buttons ( ) to
move up and down the folder/file list.
Use the cursor left button ( ) to return to the
parent folder.
Use ENTER or cursor right ( ) to open a
highlighted folder.
You can also return to the parent folder by
going to the top of the list to the ‘..’ folder,
then pressing ENTER.
01
04
02
05
03
06
Disc Navigator: Title
01- 49: - -
00:00/ 00:00 0kbps
Folder1
Folder2
Folder3
Folder4
01_DVD-S559_En.book Page 22 Friday, November 18, 2005 4:32 PM
Playing discs05
23
En
When a JPEG file is highlighted, a
thumbnail image is displayed on the right.
3 To play the highlighted track or DivX
video file or display the highlighted JPEG
file, press ENTER.
When a WMA/MP3 or DivX video file is
selected, playback begins, starting with the
selected file, and continues until the end of
the folder.
When a JPEG file is selected, a slideshow
begins, starting with that file, and
continues to the end of the folder. When
the slideshow comes to the end of the
foloder, it automatically continues to the
begining of the foloder.
Tip
To play the contents of the whole disc
rather than just the current folder, exit the
Disc Navigator and start playback using
the (play) button.
Looping a section of a disc
The A-B Repeat function allows you to specify
two points (A and B) within a track (CD, Video
CD/Super VCD) or title (DVD) that form a loop
which is played over and over.
You can’t use A-B Repeat with Video CD/
Super VCDs in PBC mode, or WMA/MP3/
DivX video files.
1 During playback, press PLAY MODE and
select ‘A-B Repeat’ from the list of
functions on the left.
2 Press ENTER on ‘A(Start Point)’ to set
the loop start point.
3 Press ENTER on ‘B(End Point)’ to set the
loop end point.
After pressing ENTER, playback jumps back to
the start point and plays the loop.
4 To resume normal playback, select ‘Off’
from the menu.
Using repeat play
There are various repeat play options,
depending on the kind of disc loaded. It’s also
possible to use repeat play together with
program play to repeat the tracks/chapters in
the program list (see Creating a program list on
page 25).
Important
You can’t use Repeat play with Video CD/
Super VCDs in PBC mode, or with WMA/
MP3 discs.
You can’t use repeat and random play at
the same time.
File1
File2
File3
File4
File5
Folder2
00:00/ 00:00 0kbps
A(Start Point)
B(End Point)
Off
A-B Repeat
Repeat
Random
Program
Search Mode
Play Mode
01_DVD-S559_En.book Page 23 Friday, November 18, 2005 4:32 PM
Playing discs
05
24
En
English
1 During playback, press PLAY MODE and
select ‘Repeat’ from the list of functions on
the left.
2 Select a repeat play option.
If program play is active, select
Program
Repeat
to repeat the program list, or
Repeat
Off
to cancel.
The repeat options available depend on the
kind of disc loaded. For example, for DVD
discs, you can select
Title Repeat
or
Chapter
Repeat
(or
Repeat Off
).
For CDs and Video CD/Super VCDs, select
Disc Repeat
or
Track Repeat
(or
Repeat
Off
).
For DivX video discs, select
Title Repeat
(or
Repeat Off
).
Using random play
Use the random play function to play titles or
chapters (DVD-Video), or tracks (CD, Video CD/
Super VCD) at random. (Note that the same
track/title/chapter may play more than once.)
You can set the random play option when a
disc is playing or stopped.
Important
Random play remains in effect until you
select
Random Off
from the random play
menu options.
You can’t use random play with VR format
DVD-RW discs, Video CD/Super VCDs
playing in PBC mode, WMA/MP3 discs,
DivX video discs, or while a DVD disc menu
is being displayed.
You can't use random play together with
program or repeat play.
1 Press PLAY MODE and select ‘Random
from the list of functions on the left.
2 Select a random play option.
The random play options available depend on
the kind of disc loaded. For example, for DVD
discs, you can select
Random Title
or
Random Chapter
(or
Random Off
).
For CDs and Video CD/Super VCDs, select
On
or
Off
to switch random play on or off.
Title Repeat
Chapter Repeat
Repeat Off
A-B Repeat
Repeat
Random
Program
Search Mode
Play Mode
Title Repeat
Chapter Repeat
Repeat Off
A-B Repeat
Repeat
Random
Program
Search Mode
Play Mode
Random Title
Random Chapter
Random Off
A-B Repeat
Repeat
Random
Program
Search Mode
Play Mode
Random Title
Random Chapter
Random Off
A-B Repeat
Repeat
Random
Program
Search Mode
Play Mode
05_playing_discs.fm Page 24 Tuesday, November 22, 2005 9:10 AM
Playing discs05
25
En
Tip
Use the following controls during random
play:
Creating a program list
This feature lets you program the play order of
titles/chapters/tracks on a disc.
Important
You can’t use Program play with VR format
DVD-RW discs, Video CD/Super VCDs
playing in PBC mode, WMA/MP3 discs,
DivX video discs, or while a DVD disc menu
is being displayed.
1 Press PLAY MODE and select ‘Program
from the list of functions on the left.
2 Select ‘Create/Edit’ from the list of
program options.
3 Use the cursor buttons and ENTER to
select a title, chapter or track for the
current step in the program list.
For a DVD disc, you can add a title or a chapter
to the program list.
For a CD or Video CD/Super VCD, select a
track to add to the program list.
After pressing ENTER to select the title/
chapter/track, the step number automatically
moves down one.
4 Repeat step 3 to build up a program list.
A program list can contain up to 24 titles/
chapters/tracks.
You can insert steps into the middle of a
program list by just highlighting the
position where you want the new step to
appear and entering a title/chapter/track
number.
To delete a step, highlight it and press
CLEAR.
5 To play the program list, press (play).
Program play remains active until you turn off
program play (see below), erase the program
list (see below), eject the disc or switch off the
player.
Button What it does
Selects a new track/title/chapter
at random.
Returns to the beginning of the
current track/title/chapter.
Create/Edit
Playback Start
Playback Stop
Program Delete
A-B Repeat
Repeat
Random
Program
Search Mode
Play Mode
Program Step
01. 01
02.
03.
04.
05.
06.
07.
08.
Title 1~38
Title 01
Title 02
Title 03
Title 04
Title 05
Title 06
Title 07
Title 08
Chapter 1~004
Chapter 001
Chapter 002
Chapter 003
Chapter 004
Program
01_DVD-S559_En.book Page 25 Friday, November 18, 2005 4:32 PM
Playing discs
05
26
En
English
Tip
Use the following controls during program
play:
Other functions available from the
program menu
There are a number of other options in the
program menu in addition to Create/Edit.
Playback Start – Starts playback of a
saved program list
Playback Stop – Turns off program play,
but does not erase the program list
Program Delete – Erases the program list
and turns off program play
Searching a disc
You can search DVD discs by title or chapter
number, or by time; CDs and Video CD/Super
VCDs by track number or time; DivX video discs
by time.
Important
Search functions are not available with
Video CD/Super VCDs in PBC mode, or
with WMA/MP3 discs.
1 Press PLAY MODE and select ‘Search
Mode’ from the list of functions on the left.
2 Select a search mode.
The search options available depend on the
kind of disc loaded.
The disc must be playing in order to use
time search.
3 Use the number buttons to enter a title,
chapter or track number, or a time.
For a time search, enter the number of
minutes and seconds into the currently
playing title (DVD/ DivX video) or track (CD/
Video CD/Super VCD) you want playback to
resume from. For example, press 4, 5, 0, 0
to have playback start from 45 minutes into
the disc. For 1 hour, 20 minutes and 30
seconds, press 8, 0, 3, 0.
4 Press ENTER to start playback.
Switching subtitles
Some DVD and DivX video discs have subtitles
in one or more languages; the disc box will
usually tell you which subtitle languages are
available. You can switch subtitle language
during playback.
1 Press SUBTITLE repeatedly to select a
subtitle option.
Note
Some discs only allow you to change
subtitle language from the disc menu.
Press TOP MENU or MENU to access.
To set subtitle preferences, see Subtitle
Language on page 31.
See Displaying DivX subtitle files on page 7
for more on DivX subtitles.
Button What it does
PLAY
MODE
Save the program list and exit
the program edit screen without
starting playback (HOME MENU
does the same).
Skip to the next step in the
program list.
0 0 1
Title Search
Chapter Search
Time Search
Input Chapter
A-B Repeat
Repeat
Random
Program
Search Mode
Play Mode
Subtitle English1/2
Current / Total
01_DVD-S559_En.book Page 26 Friday, November 18, 2005 4:32 PM
Playing discs05
27
En
Switching audio language/
channels
When playing a DVD and DivX video disc
recorded with dialog in two or more languages,
you can switch audio language during
playback.
When playing a VR format DVD-RW disc
recorded with dual-mono audio, you can
switch between the main, sub, and mixed
channels during playback.
When playing a Video CD/Super VCD, you can
switch between stereo, just the left channel or
just the right channel.
1 Press AUDIO repeatedly to select an
audio language/channel option.
The language/channel information is shown
on-screen.
Note
Some DVD discs only allow you to change
audio language from the disc menu. Press
TOP MENU or MENU to access.
To set DVD audio language preferences,
see Language settings on page 31.
Zooming the screen
Using the zoom feature you can magnify a part
of the screen by a factor of 2 or 4, while
watching a DVD, DivX video title or Video CD/
Super VCD or playing a JPEG disc.
1 During playback, use the ZOOM button
to select the zoom factor (Normal, 2x or
4x).
Since DVD, Video CD/Super VCD, DivX
video title and JPEG pictures have a fixed
resolution, picture quality will deteriorate,
especially at 4x zoom. This is not a
malfunction.
2 Use the cursor buttons to change the
zoomed area.
You can change the zoom factor and the
zoomed area freely during playback.
If the navigation square at the top of the
screen disappears, press ZOOM again to
display it.
Switching camera angles
Some DVD discs feature scenes shot from two
or more angles—check the disc box for details.
When a multi-angle scene is playing, a
icon appears on screen to let you know that
other angles are available (this can be
switched off if you prefer—see Display settings
on page 32).
1 During playback (or when paused),
press ANGLE to switch angle.
Displaying disc information
Various track, chapter and title information,
such as the elapsed and remaining playing
time can be displayed on-screen while a disc is
playing.
1 To show/switch/hide the information
displayed, press ON SCREEN repeatedly.
When a disc is playing, the information
appears at the top of the screen. Keep
pressing ON SCREEN to change the
displayed information.
01_DVD-S559_En.book Page 27 Friday, November 18, 2005 4:32 PM
Audio Settings and Video Adjust menus
06
28
En
English
Chapter 6
Audio Settings and Video
Adjust menus
Audio Settings menu
The Audio Settings menu offers features for
adjusting the way discs sound.
1 Press HOME MENU and select ‘Audio
Settings’ from the on-screen display.
2 Select and change settings using the
cursor buttons ( ), and ENTER.
Audio DRC
Settings: High, Medium, Low, Off
(default)
When watching Dolby Digital DVDs at low
volume, it’s easy to lose the quieter sounds
completely—including some of the dialog.
Switching Audio DRC (Dynamic Range
Control) to on can help by bringing up the
quieter sounds, while controlling loud peaks.
How much of a difference you hear depends on
the material you’re listening to. If the material
doesn’t have wide variations in volume, you
may not notice much change.
Note
Audio DRC is only effective with Dolby
Digital audio sources.
Audio DRC is only effective through the
digital output when Digital Out is set to
On, and Dolby Digital Out is set to Dolby
Digital > PCM (see Digital Audio Out
settings on page 30).
The effect of Audio DRC also depends on
your speakers and AV receiver settings.
Virtual Surround
Settings: On, Off (default)
Switch on Virtual Surround to enjoy realistic
surround sound effects from just two speakers.
Tip
You can also use the SURROUND button
on the remote control to switch Virtual
Surround on.
Note
Virtual Surround doesn’t work with DTS,
through either the analog or digital
outputs.
96kHz linear PCM audio is automatically
downsampled to 48kHz if Virtual Surround
is switched on.
If the player is outputting Dolby Digital,
DTS or MPEG bitstream audio (in other
words, no conversion to PCM), Virtual
Surround has no effect on the audio from
the digital output. See Digital Audio Out
settings on page 30 for how to set up the
digital output formats.
How good the surround effect is varies with
the disc.
Audio Settings
Audio Settings
Equalizer
Virtual Surround
Audio DRC
Dialog
On
Off
01_DVD-S559_En.book Page 28 Friday, November 18, 2005 4:32 PM
Audio Settings and Video Adjust menus06
29
En
Dialog
Settings: High, Medium, Low, Off
(default)
The Dialog feature is designed to make the
dialog stand out from other background
sounds in the soundtrack.
Equalizer
Settings: Rock, Pop, Live, Dance, Techno,
Classic, Soft, Off (default)
The various preset EQ curves are designed to
suit various styles of music.
Note
96kHz linear PCM audio is automatically
downsampled to 48kHz if the Equalizer is
switched on.
Video Adjust menu
From the Video Adjust screen you can adjust
various settings that affect how the picture is
presented.
1 Press HOME MENU and select ‘Video
Adjust’ from the on-screen display.
2 Make settings using the cursor buttons
( ), and ENTER.
You can adjust the following picture quality
settings:
Sharpness – Adjusts the sharpness of
edges in the picture (Fine, Standard
(default), Soft).
Brightness – Adjusts the overall
brightness (–20 to +20).
Contrast – Adjusts the contrast between
light and dark (–16 to +16).
Gamma – Adjusts the ‘warmth’ of the
picture (High, Medium, Low, Off
(default)).
Hue – Adjusts the red/green balance
(Green 9 to Red 9).
Chroma Level – Adjusts how saturated
colors appear (–9 to +9).
Adjust the Brightness, Contrast, Hue and
Chroma Level settings using the cursor left/
right ( ) buttons.
3 Press ENTER to return to the Video
Adjust screen, or HOME MENU to exit.
Video Adjust
Sharpness
Brightness
Contrast
Gamma
Hue
Chroma Level
Standard
0
0
Off
0
0
Video Adjust
Brightness min max
0
01_DVD-S559_En.book Page 29 Friday, November 18, 2005 4:32 PM
Initial Settings menu
07
30
En
English
Chapter 7
Initial Settings menu
Using the Initial Settings menu
The Initial Settings menu provides audio and
video output settings, parental lock settings,
and display settings, among others.
If an option is grayed out it means that it
cannot be changed at the current time. This is
usually because a disc is playing. Stop the
disc, then change the setting.
1 Press HOME MENU and select ‘Initial
Settings’.
2 Use the cursor buttons and ENTER to
select the setting and option you want to
set.
All the settings and options are explained on
the following pages.
Note
In the table below, the default setting is
shown in bold: other settings are shown in
italics.
The Digital Audio Out settings only need to
be set if you have connected the digital
output of this player to an AV receiver, or
other equipment.
Check the owner’s manual supplied with
your other equipment to see which digital
audio formats it’s compatible with.
Some settings, such as TV Screen, Audio
Language and Subtitle Language may be
overridden by the DVD disc. Often these
settings can also be made from the DVD
disc menu.
Digital Audio Out settings
Initial Settings
Setting Option What it means
Digital Out On
Digital audio is output from the digital outputs.
Off
No digital audio output.
Dolby Digital Out Dolby Digital
Dolby Digital encoded digital audio is output when playing a
Dolby Digital DVD disc.
Dolby Digital > PCM
Dolby Digital audio is converted to PCM audio before being
output.
DTS Out DTS
DTS encoded digital audio is output when playing a DTS disc.
(Noise will be output if your amplifier/receiver is not compatible
with DTS audio.)
Off
No digital audio is output when playing a DTS disc.
96 kHz PCM Out 96kHz > 48kHz
96kHz digital audio is converted to 48kHz for digital output.
96kHz
96kHz digital audio is output as is at 96kHz.
01_DVD-S559_En.book Page 30 Friday, November 18, 2005 4:32 PM
Initial Settings menu07
31
En
Video Output settings
Language settings
MPEG Out MPEG > PCM
MPEG encoded digital audio is converted to PCM audio for
digital output.
MPEG
MPEG encoded digital audio is output as is.
Setting Option What it means
TV Screen
(See also Screen sizes
and disc formats on
page 36.)
4:3 (Letter Box)
Set if you have a conventional 4:3 TV. Widescreen movies are
shown with black bars top and bottom.
4:3 (Pan & Scan)
Set if you have a conventional 4:3 TV. Widescreen movies are
shown with the sides cropped so that the image fills the screen.
16:9 (Wide)
Set if you have a widescreen TV.
Component Out Interlace
Set if your TV is not compatible with progressive scan video.
Progressive
Set if your TV is compatible with progressive scan video (see
your TV’s instruction manual for details). See also Switching
the video output to interlace using the front panel controls on
page 10.
Note that progressive scan video is only output from the
component video jacks.
AV Connector Out Video
Ordinary (composite) video output, compatible with all TVs.
RGB
If your TV is compatible, this setting gives the best picture
quality.
Note that there is no output from the component jacks when
this setting selected.
Setting Option What it means
Setting Option What it means
Audio Language English
If there is an English soundtrack on the disc then it will be
played.
Languages as displayed
If there is the language selected on the disc, then it will be
played.
Other Language
Select to choose a language other than the ones displayed (see
page 37).
Subtitle Language
(See also Displaying
DivX subtitle files on
page 7.)
English
If there are English subtitles on the disc then they will be
displayed.
Languages as displayed
If there is the subtitle language selected on the disc, then it will
be displayed.
Other Language
Select to choose a language other than the ones displayed (see
page 37).
01_DVD-S559_En.book Page 31 Friday, November 18, 2005 4:32 PM
Initial Settings menu
07
32
En
English
Display settings
Options settings
DVD Menu Lang. w/Subtitle Lang.
DVD disc menus will be displayed in the same language as
your selected subtitle language, if possible.
Languages as displayed
DVD disc menus will be displayed in the selected language, if
possible.
Other Language
Select to choose a language other than the ones displayed (see
page 37).
Subtitle Display On
Subtitles are displayed according to your selected subtitle
language (see above).
Off
Subtitles are always off by default when you play a DVD disc
(note that some discs override this setting).
Setting Option What it means
Setting Option What it means
OSD Language English
On-screen displays of the player are in English.
Languages as displayed
On-screen displays are shown in the language selected.
Angle Indicator On
A camera icon is displayed on-screen during multi-angle
scenes on a DVD disc.
Off
No multi-angle indication is shown.
Setting Option What it means
Parental Lock
See Parental Lock on page 33.
DivX VOD Display
See About DivX® VOD content on page 34.
01_DVD-S559_En.book Page 32 Friday, November 18, 2005 4:32 PM
Initial Settings menu07
33
En
Parental Lock
Default level: Off; Default password: none;
Default Country/Area code: us (2119)
To give you some control over what your
children watch on your DVD player, some DVD-
Video discs feature a Parental Lock level. If
your player is set to a lower level than the disc,
the disc won’t play.
Some discs also support the Country/Area
Code feature. The player does not play certain
scenes on these discs, depending on the
Country/Area Code you set.
Note
Not all discs use Parental Lock, and will
play without requiring the password first.
If you forget your password, you’ll need to
reset the player to register a new password.
(see Resetting the player on page 37)
Registering a new password
You must register a password before you can
change the Parental Lock level or enter a
Country code.
1 Select ‘Options’, then ‘Password’.
2 Use the number buttons to enter a 4-
digit password.
The numbers you enter show up as asterisks
(*) on-screen.
3 Press ENTER to register the password.
You will return to the Options menu screen.
Changing your password
To change your password, confirm your
existing password then enter a new one.
1 Select ‘Password Change’.
2 Use the number buttons to enter your
existing password, then press ENTER.
3 Enter a new password and press ENTER.
This registers the new password and you will
return to the Options menu screen.
Setting/changing the Parental Lock
1 Select ‘Level Change’.
2 Use number buttons to enter your
password, then press ENTER.
3 Select a new level and press ENTER.
Press the cursor left ( ) repeatedly to lock
more levels (more discs will require the
password); press the cursor right ( ) to
unlock levels. You can’t lock level 1.
This sets the new level and you will return to the
Options menu screen.
Setting/changing the Country/Area
code
You can find the Country/Area code list on
page 38.
1 Select ‘Country Code’.
2 Use number buttons to enter your
password, then press ENTER.
3 Select a Country/Area code and press
ENTER.
There are two ways you can do this:
Select by code letter: Use the cursor up/
down ( ) to change the Country/Area
code.
Select by code number: Press the cursor
right ( ) then use the number buttons to
enter the 4-digit Country/Area code.
The new Country/Area code is set and you will
return to the Options menu screen. Note that
the new Country/Area code doesn’t take effect
until the next disc is loaded (or the current disc
is reloaded).
Digital Audio Out
Video Output
Language
Display
Options
Parental Lock
DivX VOD
Password
Level Change
Country Code
Initial Settings
01_DVD-S559_En.book Page 33 Friday, November 18, 2005 4:32 PM
Initial Settings menu
07
34
En
English
About DivX
®
VOD content
In order to play DivX VOD (video on demand)
content on this player, you first need to register
the player with your DivX VOD content
provider. You do this by generating a DivX VOD
registration code, which you submit to your
provider.
Important
DivX VOD content is protected by a DRM
(Digital Rights Management) system. This
restricts playback of content to specific,
registered devices.
If you load a disc that contains DivX VOD
content not authorized for your player, the
message Authorization Error is displayed
and the content will not play.
Resetting the player (page 37) will not
cause you to lose your registration code.
Displaying your DivX VOD
registration code
1 Press HOME MENU and select ‘Initial
Settings’.
2 Select ‘Options’, then ‘DivX VOD’.
3 Select ‘Display’.
Your 8-digit registration code is displayed.
Make a note of the code as you will need it
when you register with a DivX VOD provider.
Playing DivX
®
VOD content
Some DivX VOD content may only be playable
a fixed number of times. When you load a disc
containing this type of DivX VOD content, the
remaining number of plays is shown on-screen
and you then have the option of playing the
disc (thereby using up one of the remaining
plays), or stopping. If you load a disc that
contains expired DivX VOD content (for
example, content that has zero remaining
plays), the message Rental Expired is
displayed.
If your DivX VOD content allows an unlimited
number of plays, then you may load the disc
into your player and play the content as often
as you like, and no message will be displayed.
Digital Audio Out
Video Output
Language
Display
Options
Parental Lock
DivX VOD
Display
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
Initial Settings
DivX VOD Registration Code
0 1 2 3 4 5 6 7
01_DVD-S559_En.book Page 34 Friday, November 18, 2005 4:32 PM
Additional information08
35
En
Chapter 8
Additional information
Taking care of your player and
discs
General
Hold discs by the edge or by the center hole
and edge.
When you're not using a disc, return it to its
case and store upright. Avoid leaving discs in
excessively cold, humid, or hot environments
(including under direct sunlight).
Don't glue paper or put stickers on to discs. Do
not use a pencil, ball-point pen or other sharp-
tipped writing instrument to write on the disc.
Don’t use self-adhesive disc labels on discs as
these can cause the disc to warp slightly
during playback causing distortion in the
picture and/or sound.
Damaged and shaped discs
Do not use cracked, chipped, warped, or
otherwise damaged discs as they may damage
the player.
This player is designed to be used only with
conventional, fully circular discs. Do not use
shaped discs. YAMAHA disclaims all liability
arising in connection with the use of shaped
discs.
Cleaning discs
Fingerprints and dust on discs can affect
playback performance. Clean using a soft, dry
cloth, wiping the disc lightly from the center to
the outside edge as shown below.
If necessary, use a cloth soaked in alcohol, or a
commercially available CD/DVD cleaning kit to
clean a disc more thoroughly. Never use
benzine, thinner or other cleaning agents,
including products designed for cleaning vinyl
records.
Cleaning the unit’s exterior
Unplug the unit before cleaning.
Use a dry cloth to wipe off dust and dirt. If the
surfaces are very dirty, wipe with a soft cloth
dipped in some neutral cleanser diluted five or
six times with water and wrung out well, then
wipe again with a dry cloth.
Do not use furniture wax or cleaners. Never
use thinners, benzine or insecticide sprays or
other chemicals on or near this unit.
If you use a chemical-impregnated cleaning
cloth, read the instructions carefully before
use. These cloths may leave smear marks on
half-mirror finish surfaces; if this happens,
finish with a dry cloth.
01_DVD-S559_En.book Page 35 Friday, November 18, 2005 4:32 PM
Additional information
08
36
En
English
Cleaning the pickup lens
The DVD player’s lens should not become dirty
in normal use, but if for some reason it should
malfunction due to dust or dirt, consult your
nearest YAMAHA authorized service center.
We do not recommend using commercially
available lens cleaners for CD players.
Condensation
Condensation may form inside the player if it is
brought into a warm room from outside, or if
the temperature of the room rises quickly.
Although the condensation won’t damage the
player, it may temporarily impair its
performance. Leave it to adjust to the warmer
temperature for about an hour before
switching on.
Moving the player
If you need to move the player, first press
STANDBY/ON on the front panel to turn the
player off. Wait for -OFF- to disappear from the
display, then unplug the power cable. Never lift
or move the unit during playback—discs rotate
at a high speed and may be damaged.
Screen sizes and disc formats
DVD-Video discs come in several different
screen aspect ratios, ranging from TV
programs, which are generally 4:3, to
CinemaScope widescreen movies, with an
aspect ratio of up to about 7:3.
Televisions, too, come in different aspect
ratios; ‘standard’ 4:3 and widescreen 16:9.
Widescreen TV users
If you have a widescreen TV, the TV Screen
setting (page 31) of this player should be set to
16:9 (Wide).
When you watch discs recorded in 4:3 format,
you can use the TV controls to select how the
picture is presented. Your TV may offer various
zoom and stretch options; see the instructions
that came with your TV for details.
Please note that some movie aspect ratios are
wider than 16:9, so even though you have a
widescreen TV, these discs will still play in a
‘letter box’ style with black bars at the top and
bottom of the screen.
Standard TV users
If you have a standard TV, the TV Screen
setting (page 31) of this player should be set to
4:3 (Letter Box) or 4:3 (Pan&Scan),
depending on which you prefer.
Set to 4:3 (Letter Box), widescreen discs are
shown with black bars top and bottom.
Set to 4:3 (Pan&Scan), widescreen discs are
shown with the left and right sides cropped.
Although the picture looks larger, you don’t
actually see the whole picture.
Please note that many widescreen discs
override the player’s settings so that the disc is
shown in letter box format regardless of the
setting.
Note
Using the 16:9 (Wide) setting with a
standard 4:3 TV, or either of the 4:3 settings
with a widescreen TV, will result in a
distorted picture.
01_DVD-S559_En.book Page 36 Friday, November 18, 2005 4:32 PM
Additional information08
37
En
Setting the TV system
The default setting of this player is AUTO, and
unless you notice that the picture is distorted
when playing some discs, you should leave it
set to AUTO. If you experience picture distor-
tion with some discs, set the TV system to
match your country or region’s system. Doing
this, however, may restrict the kinds of disc you
can watch. The table below shows what kinds
of disc are compatible with each setting
(AUTO, PAL and NTSC).
1 If the player is on, press STANDBY/ON
to switch it to standby.
2 Using the front panel controls, hold
down then press STANDBY/ON to
switch the TV system.
The TV system changes as follows:
AUTO NTSC
NTSC PAL
PAL AUTO
Note
You have to switch the player into standby
(press STANDBY/ON) before each
change.
Resetting the player
Use this procedure to reset all the player’s
settings to the factory default.
1 Switch the player into standby.
2 Using the front panel buttons, hold
down the (stop) button and press
STANDBY/ON to switch the player back on.
All the player’s settings are now reset.
DVD-Video regions
All DVD-Video discs carry a region mark on the
case somewhere that indicates which
region(s) of the world the disc is compatible
with. Your DVD player also has a region mark,
which you can find on the rear panel. Discs
from incompatible regions will not play in this
player. Discs marked ALL will play in any
player.
The diagram below shows the various DVD
regions of the world.
Selecting languages using the
language code list
Some of the language options (such as ‘DVD
Language’ in the Setup Navigator) allow you to
set your preferred language from any of the 136
languages listed in the language code list on
page 38.
1 Select ‘Other Language’.
2 Use the cursor left/right ( ) buttons
to select either a code letter or a code
number.
3 Use the cursor up/down ( ) buttons
to select a code letter or a code number.
See Language code list on page 38 for a
complete list of languages and codes.
Disc Player setting
Type Format NTSC PAL AUTO
DVD/Super VCD/
Video CD/DivX
Video
NTSC
NTSC PAL NTSC
PAL
NTSC PAL PAL
CD/MP3/WMA/
JPEG
no disc
NTSC PAL NTSC or
PAL
1
2
2
5
5
6
3
2
1
4
4
01_DVD-S559_En.book Page 37 Friday, November 18, 2005 4:32 PM
Additional information
08
38
En
English
Language code list
Language (Language code letter), Language code
Country/Area code list
Country/Area, Country/Area code, Country/Area code letter
Japanese (ja), 1001
English (en), 0514
French (fr), 0618
German (de), 0405
Italian (it), 0920
Spanish (es), 0519
Chinese (zh), 2608
Dutch (nl), 1412
Portuguese (pt), 1620
Swedish (sv), 1922
Russian (ru), 1821
Korean (ko), 1115
Greek (el), 0512
Afar (aa), 0101
Abkhazian (ab), 0102
Afrikaans (af), 0106
Amharic (am), 0113
Arabic (ar), 0118
Assamese (as), 0119
Aymara (ay), 0125
Azerbaijani (az), 0126
Bashkir (ba), 0201
Byelorussian (be), 0205
Bulgarian (bg), 0207
Bihari (bh), 0208
Bislama (bi), 0209
Bengali (bn), 0214
Tibetan (bo), 0215
Breton (br), 0218
Catalan (ca), 0301
Corsican (co), 0315
Czech (cs), 0319
Welsh (cy), 0325
Danish (da), 0401
Bhutani (dz), 0426
Esperanto (eo), 0515
Estonian (et), 0520
Basque (eu), 0521
Persian (fa), 0601
Finnish (fi), 0609
Fiji (fj), 0610
Faroese (fo), 0615
Frisian (fy), 0625
Irish (ga), 0701
Scots-Gaelic (gd), 0704
Galician (gl), 0712
Guarani (gn), 0714
Gujarati (gu), 0721
Hausa (ha), 0801
Hindi (hi), 0809
Croatian (hr), 0818
Hungarian (hu), 0821
Armenian (hy), 0825
Interlingua (ia), 0901
Interlingue (ie), 0905
Inupiak (ik), 0911
Indonesian (in), 0914
Icelandic (is), 0919
Hebrew (iw), 0923
Yiddish (ji), 1009
Javanese (jw), 1023
Georgian (ka), 1101
Kazakh (kk), 1111
Greenlandic (kl), 1112
Cambodian (km), 1113
Kannada (kn), 1114
Kashmiri (ks), 1119
Kurdish (ku), 1121
Kirghiz (ky), 1125
Latin (la), 1201
Lingala (ln), 1214
Laothian (lo), 1215
Lithuanian (lt), 1220
Latvian (lv), 1222
Malagasy (mg), 1307
Maori (mi), 1309
Macedonian (mk), 1311
Malayalam (ml), 1312
Mongolian (mn), 1314
Moldavian (mo), 1315
Marathi (mr), 1318
Malay (ms), 1319
Maltese (mt), 1320
Burmese (my), 1325
Nauru (na), 1401
Nepali (ne), 1405
Norwegian (no), 1415
Occitan (oc), 1503
Oromo (om), 1513
Oriya (or), 1518
Panjabi (pa), 1601
Polish (pl), 1612
Pashto, Pushto (ps), 1619
Quechua (qu), 1721
Rhaeto-Romance (rm), 1813
Kirundi (rn), 1814
Romanian (ro), 1815
Kinyarwanda (rw), 1823
Sanskrit (sa), 1901
Sindhi (sd), 1904
Sangho (sg), 1907
Serbo-Croatian (sh), 1908
Sinhalese (si), 1909
Slovak (sk), 1911
Slovenian (sl), 1912
Samoan (sm), 1913
Shona (sn), 1914
Somali (so), 1915
Albanian (sq), 1917
Serbian (sr), 1918
Siswati (ss), 1919
Sesotho (st), 1920
Sundanese (su), 1921
Swahili (sw), 1923
Tamil (ta), 2001
Telugu (te), 2005
Tajik (tg), 2007
Thai (th), 2008
Tigrinya (ti), 2009
Turkmen (tk), 2011
Tagalog (tl), 2012
Setswana (tn), 2014
Tonga (to), 2015
Turkish (tr), 2018
Tsonga (ts), 2019
Tatar (tt), 2020
Twi (tw), 2023
Ukrainian (uk), 2111
Urdu (ur), 2118
Uzbek (uz), 2126
Vietnamese (vi), 2209
Volapük (vo), 2215
Wolof (wo), 2315
Xhosa (xh), 2408
Yoruba (yo), 2515
Zulu (zu), 2621
Argentina, 0118, ar
Australia, 0121, au
Austria, 0120, at
Belgium, 0205, be
Brazil, 0218, br
Canada, 0301, ca
Chile, 0312, cl
China, 0314, cn
Denmark, 0411, dk
Finland, 0609, fi
France, 0618, fr
Germany, 0405, de
Hong Kong, 0811, hk
India, 0914, in
Indonesia, 0904, id
Italy, 0920, it
Japan, 1016, jp
Korea, Republic of, 1118, kr
Malaysia, 1325, my
Mexico, 1324, mx
Netherlands, 1412, nl
New Zealand, 1426, nz
Norway, 1415, no
Pakistan, 1611, pk
Philippines, 1608, ph
Portugal, 1620, pt
Russian Federation, 1821, ru
Singapore, 1907, sg
Spain, 0519, es
Sweden, 1905, se
Switzerland, 0308, ch
Taiwan, 2023, tw
Thailand, 2008, th
United Kingdom, 0702, gb
USA, 2119, us
01_DVD-S559_En.book Page 38 Friday, November 18, 2005 4:32 PM
Additional information08
39
En
Glossary
*1
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
*2
“DTS” and “DTS Digital Out” are registered
trademarks of Digital Theater Systems, Inc.
Analog audio Direct representation of sound by an
electrical signal. See also Digital audio.
Aspect ratio The width of a TV screen relative to its
height. Conventional TVs are 4:3;
widescreen models are 16:9.
Digital audio Indirect representation of sound using
numbers. See also Sampling frequency
and Analog audio.
Dolby
Digital
*1
A multi-channel audio encoding system
developed by Dolby Laboratories that
enables far more audio to be stored on a
disc than PCM encoding. See also PCM
(Pulse Code Modulation).
DRM
WMA)
DRM (Digital Rights Management) copy
protection is a technology designed to
prevent unauthorized copying by
restricting playback, etc. of material on
devices other the PC (or other WMA
recording equipment) used to record it.
For detailed information, please see the
instruction manuals or help files that
came with your PC (or other WMA
recording equipment) and/or software.
DTS
*2
A multi-channel audio encoding system
developed by Digital Theater Systems
that enables far more audio to be stored
on a disc than PCM encoding. See also
PCM (Pulse Code Modulation)
.
EXIF
(Exchangeable
Image File)
A file format developed by Fuji Photo
Film for digital still cameras. Digital
cameras from various manufacturers
use this compressed file format which
carries date, time and thumbnail
information, as well as the picture data.
File extension
A tag added to the end of a filename to
indicate the type of file. For example,
“.mp3” indicates an MP3 file.
ISO 9660
format
International standard for the volume
and file structure of CD-ROM discs.
JPEG
A standard file format used for still
images. JPEG files are identified by the
file extension “.jpg”.
MP3
MP3 (MPEG1 audio layer 3) is a
compressed stereo audio file format.
Files are recognized by their file
extension “.mp3”.
MPEG audio
An audio format used on Video CD/
Super VCDs and some DVD discs.
PBC
(PlayBack
Control)
A system of navigating a Video CD/
Super VCD through on-screen menus
recorded onto the disc.
PCM
(Pulse Code
Modulation)
Digital audio encoding system found on
CDs. Good quality, but requires a lot of
data compared to Dolby Digital, DTS
and MPEG encoded audio. See also
Digital audio
.
Progressive
scan video
All the lines that make up a video picture
are updated in one pass (compared to
interlace which takes two passes to
update the whole picture).
Regions
These associate DVD-Video discs and
players with particular areas of the
world. See
DVD-Video regions
on
page 37 for more information.
Sampling
frequency
The rate at which sound is measured to
be turned into digital audio data. The
higher the rate, the better the sound
quality. CD is 44.1 kHz; DVD can be up
to 96 kHz. See also
Digital audio
.
WMA
WMA is short for Windows Media Audio
and refers to an audio compression
technology developed by Microsoft
Corporation. Files are recognized by
their file extension “.wma”.
Microsoft, Windows Media, and the
Windows logo are trademarks, or
registered trademarks of Microsoft
Corporation in the United States and/or
other countries.
01_DVD-S559_En.book Page 39 Friday, November 18, 2005 4:32 PM
Additional information
08
40
En
English
Specifications
General
System . . . . . . . . . . . . . . . . . . . . . . . . DVD player
Power requirements . . .AC 220–240 V, 50/60 Hz
Power consumption . . . . . . . . . . . . . . . . . . . 7 W
Power consumption (standby) . . . . . . . . . 0.7 W
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.8 kg
Dimensions . . . . 435 (W) x 61 (H) x 213 (D) mm
Operating temperature . . . . . . . . +5°C to +35°C
RGB (SCART) output
Output level . . . . . . . . . . . . . . . . . 0.7 Vp-p (75
)
Connection. . . . . . . . . . . . . . . . . . Euroconnector
Component video output
Y (luminance) - Output level
. . . . . . . . . . . . . . . . . . . . . . . .1 Vp-p (75
)(Green)
P
b/Cb
(color) - Output level
. . . . . . . . . . . . . . . . . . . . . . . 0.7 Vp-p (75
)(Blue)
P
r/Cr
(color) - Output level
. . . . . . . . . . . . . . . . . . . . . . . . 0.7 Vp-p (75
)(Red)
Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . RCA
S-video output
Y (luminance) - Output level . . . . . . 1 Vp-p (75
)
C (color) - Output level . . . . . . 286 mVp-p (75
)
Connection. . . . . . . . .S-video (Mini, DIN, 4 pins)
Video output
Output level . . . . . . . . . . . . . . . . . . 1 Vp-p (75
)
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA
Audio output (1 stereo pair)
Output level. . . . . . . . . . . . . During audio output
200 mVrms (1 kHz, –20 dB)
Number of channels . . . . . . . . . . . . . . . . . . . . . 2
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA
Digital audio characteristics
Frequency response . . . . . . . . . . 4 Hz to 44 kHz
(DVD fs: 96 kHz)
S/N ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .115 dB
Dynamic range . . . . . . . . . . . . . . . . . . . . . .101 dB
Total harmonic distortion. . . . . . . . . . . . 0.0023 %
Digital output
Coaxial digital output . . . . . . . . . . . . . . . . . . .RCA
IEC60958 for CDDA/LPCM
IEC61937 for MPEG 1/2,
Dolby Digital and DTS
Accessories
Audio/video cable. . . . . . . . . . . . . . . . . . . . . . . . 1
Power cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA/R6 dry cell batteries . . . . . . . . . . . . . . . . . . 2
Owner’s manual
The specifications and design of this product are subject to
change without notice, due to improvement.
10_additional_info.fm Page 40 Tuesday, November 22, 2005 11:36 AM
2005 All rights reserved.
YAMAHA ELECTRONICS CORPORATION, USA
6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.
135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.
SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.
RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.
YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J A WETTERGRENS GATA 1, BOX 30053, 400 43 V€ STRA FR…LUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD.
17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Thailand J2G53923A
(WG69420)
J2G53923A SH 06/01
U
DVD-S559_Ru.book Page 47 Friday, November 18, 2005 6:58 PM

Documenttranscriptie

01_DVD-S559_En.book Page 0 Friday, November 18, 2005 4:32 PM G DVD PLAYER LECTEUR DE DVD DVD-S559 OWNER'S MANUAL MODE D'EMPLOI 01_DVD-S559_En.book Page 1 Friday, November 18, 2005 4:32 PM CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place — away from direct sunlight, heat sources, vibration, dust, moisture, or cold. In a cabinet, allow about 2.5 cm (1 inch) of free space all around this unit for adequate ventilation. 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. 4 Do not expose this unit to sudden temperature changes from cold to hot, nor locate this unit in an environment with high humidity (i.e., a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. 5 Avoid installing this unit in a location where foreign objects may fall onto this unit or where this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: – Other components, as they may cause damage and/or discoloration on the surface of this unit. – Burning objects (i.e., candles), as they may cause fire, damage to this unit, and/or personal injury. – Containers with liquid in them, as they may fall, spilling the liquid and causing an electrical shock to the user and/or damage to this unit. 6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. 7 Do not plug in this unit to a wall outlet until all connections are complete. 8 Do not operate this unit upside-down. It may overheat, possibly causing damage. 9 Do not use excessive force on switches, knobs and/or cords. 10 When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord. 11 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. 12 Use only the voltage specified on this unit. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than as specified. 1 En 13 To prevent damage by lightning, keep the power cord out and outdoor antennas disconnected from a wall outlet or the unit during a lightning storm. 14 Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reason. 15 When not planning to use this unit for long periods of time (i.e., vacation), disconnect the AC power plug from the wall outlet. 16 Be sure to read the “Troubleshooting” section on common operating errors before concluding that this unit is faulty. 17 Before moving this unit, press STANDBY/ON to set the unit in standby mode, then disconnect the AC power plug from the wall outlet. 18 Install this unit near the AC outlet and where the AC power plug can be reached easily. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. LASER SAFETY This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device. DANGER This unit emits visible laser radiation when open. Avoid direct eye exposure to beam. When this unit is plugged into a wall outlet, do not place your eyes close to the opening of the disc tray and other openings or look inside. 01_DVD-S559_En.book Page 2 Friday, November 18, 2005 4:32 PM Contents 01 Thank you for purchasing this YAMAHA product. Contents 01 Before you start 05 Playing discs Features . . . . . . . . . . . . . . . . . . . . . . . . . . . What’s in the box . . . . . . . . . . . . . . . . . . . . Hints on installation . . . . . . . . . . . . . . . . . . Disc/content format playback compatibility 4 4 5 5 02 Connecting up Easy connections . . . . . . . . . . . . . . . . . . . . 8 Connecting using a SCART AV cable . . . . . 9 Connecting using the S-video output . . . . . 9 Connecting using the component video output . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Connecting to an AV receiver . . . . . . . . . . 11 03 Controls and displays Front panel . . . . . . . . . . . . . . . . . . . . . . . . 12 Remote control . . . . . . . . . . . . . . . . . . . . 13 04 Getting started Switching on . . . . . . . . . . . . . . . . . . . . . . Using the on-screen displays . . . . . . . . . . Setting up the player for your TV . . . . . . . . Setting the language of this player’s on-screen displays . . . . . . . . . . . . . . . . . . Playing discs . . . . . . . . . . . . . . . . . . . . . . English Please read through this owner’s manual so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference. 14 14 15 15 16 Scanning discs . . . . . . . . . . . . . . . . . . . . .20 Playing in slow motion . . . . . . . . . . . . . . . .20 Frame advance/frame reverse . . . . . . . . . .21 Viewing a JPEG slideshow . . . . . . . . . . . . .21 Browsing DVD or Video CD/Super VCD disc with the Disc Navigator . . . . . . . . . . . . . . .21 Browsing WMA, MP3, DivX video and JPEG files with the Disc Navigator . . . . . . .22 Looping a section of a disc . . . . . . . . . . . .23 Using repeat play . . . . . . . . . . . . . . . . . . . .23 Using random play . . . . . . . . . . . . . . . . . .24 Creating a program list . . . . . . . . . . . . . . .25 Searching a disc . . . . . . . . . . . . . . . . . . . .26 Switching subtitles . . . . . . . . . . . . . . . . . .26 Switching audio language/channels . . . . .27 Zooming the screen . . . . . . . . . . . . . . . . . .27 Switching camera angles . . . . . . . . . . . . .27 Displaying disc information . . . . . . . . . . . .27 06 Audio Settings and Video Adjust menus Audio Settings menu . . . . . . . . . . . . . . . . .28 Video Adjust menu . . . . . . . . . . . . . . . . . .29 2 En 01_DVD-S559_En.book Page 3 Friday, November 18, 2005 4:32 PM 01 Contents 07 Initial Settings menu Using the Initial Settings menu . . . . . . . . .30 Digital Audio Out settings . . . . . . . . . . . . .30 Video Output settings . . . . . . . . . . . . . . . .31 Language settings . . . . . . . . . . . . . . . . . . .31 Display settings . . . . . . . . . . . . . . . . . . . . .32 Options settings . . . . . . . . . . . . . . . . . . . .32 Parental Lock . . . . . . . . . . . . . . . . . . . . . . .33 08 Additional information Taking care of your player and discs . . . . .35 Screen sizes and disc formats . . . . . . . . . .36 Setting the TV system . . . . . . . . . . . . . . . .37 Resetting the player . . . . . . . . . . . . . . . . . .37 DVD-Video regions . . . . . . . . . . . . . . . . . . .37 Selecting languages using the language code list . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Language code list. . . . . . . . . . . . . . . . . . .38 Country/Area code list . . . . . . . . . . . . . . . .38 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Specifications . . . . . . . . . . . . . . . . . . . . . .40 3 En 01_DVD-S559_En.book Page 4 Friday, November 18, 2005 4:32 PM Before you start 01 Chapter 1 Features • 24-bit/192kHz compatible DAC The on-board 24-bit/192kHz DAC means that this player is fully compatible with high sampling-rate discs, capable of delivering exceptional sound quality in terms of dynamic range, low-level resolution and high-frequency detail. • Excellent audio performance surround sound entertainment with Dolby Digital *1 and DTS*2 software Logos: When connected to a suitable AV amplifier or receiver, this player gives great surround sound with Dolby Digital and DTS discs. • PureCinema Progressive Scan video When connected to a progressive scancompatible TV or monitor using the component video outputs, you can enjoy extremely stable, flicker free images, with the same frame refresh rate as the original movie. • New Disc Navigator with moving pictures The new Disc Navigator enables you play the first few seconds of each title or chapter in a thumbnail image on screen. • DSP effects for enhanced playback See Audio Settings and Video Adjust menus on page 28. • DivX video compatibility See DivX video compatibility on page 7. English Before you start • Energy saving design An auto power-off function switches the player into standby if not used for about 30 minutes. *1 Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. *2 “DTS” and “DTS Digital Out” are registered trademarks of Digital Theater Systems Inc. What’s in the box Please confirm that the following accessories are in the box when you open it. • Remote control • AA/R6 dry cell batteries x2 • Audio/video cable (red/white/yellow plugs) • Power cable • Owner’s Manual Putting the batteries in the remote • Open the battery compartment cover and insert the batteries as shown. Use two AA/R6 batteries and follow the indications (, ) inside the compartment. Close the cover when you’re finished. • Picture zoom See Zooming the screen on page 27. • MP3 and WMA compatibility See Compressed audio compatibility on page 6. • JPEG compatibility See JPEG file compatibility on page 7. 4 En 01_DVD-S559_En.book Page 5 Friday, November 18, 2005 4:32 PM 01 Before you start Important Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following: • Don’t mix new and old batteries together. • Don’t use different kinds of battery together—although they may look similar, different batteries may have different voltages. • Make sure that the plus and minus ends of each battery match the indications in the battery compartment. • Remove batteries from equipment that isn’t going to be used for a month or more. • When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area. Hints on installation We want you to enjoy using this product for years to come, so please use the following guidelines when choosing a suitable location: • Use near a television or monitor as you may experience interference—especially if the television uses an indoor antenna. • Use in a kitchen or other room where the player may be exposed to smoke or steam. • Use on a thick rug or carpet, or cover with cloth—this may prevent proper cooling of the unit. • Place on an unstable surface, or one that is not large enough to support all four of the unit’s feet. Disc/content format playback compatibility This player is compatible with a wide range of disc types (media) and formats. Playable discs will generally feature one of the following logos on the disc and/or disc packaging. Note however that some disc types, such as recordable CD and DVD, may be in an unplayable format—see below for further compatibility information. Please also note that recordable discs cannot be recorded using this player. Do... • Use in a well-ventilated room. DVD-Video • Place on a solid, flat, level surface, such as a table, shelf or stereo rack. DVD+ReWritable Don’t... DVD+Rewritable • Use in a place exposed to high temperatures or humidity, including near radiators and other heat-generating appliances. Audio CD DVD-R DVD-RW DVD+R DVD+R DL DVD+R Video CD CD-R DVD+RDL CD-RW • Place on a window sill or a place where the player will be exposed to direct sunlight. Fujicolor CD • Use in an excessively dusty or damp environment. • Place directly on top of an amplifier, or other component in your stereo system that becomes hot in use. 5 En • is a trademark of Fuji Photo Film Co. Ltd. • Also compatible with KODAK Picture CD 01_DVD-S559_En.book Page 6 Friday, November 18, 2005 4:32 PM Before you start Super VCD • DRM (Digital Rights Management) compatible: Yes (DRM-protected audio files will not play in this player—see also DRM in the Glossary on page 39) • File extensions: .mp3, .wma (these must be used for the player to recognize MP3 and WMA files – do not use for other file types) English This player supports the IEC’s Super VCD standard. Compared to the Video CD standard, Super VCD offers superior picture quality, and allows two stereo soundtracks to be recorded. Super VCD also supports the widescreen size. 01 About WMA CD-R/RW compatibility • Compatible formats: CD-Audio, Video CD/ Super VCD, ISO 9660 CD-ROM* containing MP3, WMA, JPEG or DivX video files * ISO 9660 Level 1 or 2 compliant. CD physical format: Mode1, Mode2 XA Form1. Romeo and Joliet file systems are both compatible with this player. • Multi-session playback: No • Unfinalized disc playback: No • File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder DVD+R/RW, DVD-R/RWcompatibility • Compatible formats: DVD-Video, Video Recording (VR)* * DVD-RW only. Edit points may not play exactly as edited; screen may go momentarily blank at edited points. The Windows Media® logo indicates that this player can playback Windows Media Audio content. WMA is an acronym for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA content can be encoded by using Windows Media® Player version 7, 7.1, Windows Media® Player for Windows® XP, or Windows Media® Player 9 Series. Microsoft, Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/ or other countries. • Unfinalized playback: No • WMA/MP3/JPEG file playback on DVD+R/ RW, DVD-R/RW: No Compressed audio compatibility • Compatible formats: MPEG-1 Audio Layer 3 (MP3), Windows Media Audio (WMA) • Sampling rates: 32, 44.1 or 48kHz • Bit-rates: Any (128Kbps or higher recommended) About DivX DivX is a compressed digital video format created by the DivX® video codec from DivXNetworks, Inc. This player can play DivX video files burned on CD-R/RW/ROM discs. Keeping the same terminology as DVD-Video, individual DivX video files are called "Titles". When naming files/titles on a CD-R/RW disc prior to burning, keep in mind that by default they will be played in alphabetical order. • VBR (variable bit rate) MP3 playback: No • VBR WMA playback: No • WMA lossless encoding compatible: No 6 En 01_DVD-S559_En.book Page 7 Friday, November 18, 2005 4:32 PM 01 Before you start Displaying DivX subtitle files The font sets listed below are available for DivX external subtitle files. You can see the proper font set on-screen by setting the Subtitle Language (in Language settings on page 31) to match the subtitle file. This player supports the following language groups: Group 1: Albanian (sq), Basque (eu), Catalan (ca), Danish (da), Dutch (nl), English (en), Faroese (fo), Finnish (fi), French (fr), German (de), Icelandic (is), Irish (ga), Italian (it), Norwegian (no), Portuguese (pt), RhaetoRomanic (rm), Scottish (gd), Spanish (es), Swedish (sv) Group 2: Albanian (sq), Croatian (hr), Czech (cs), Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk), Slovenian (sl) Group 3: Bulgarian (bg), Byelorussian (be), Macedonian (mk), Russian (ru), Serbian (sr), Ukrainian (uk) Group 4: Hebrew (iw), Yiddish (ji) Group 5: Turkish (tr) DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc. and are used under license. • Some external subtitle files may be displayed incorrectly or not at all. • For external subtitle files the following subtitle format filename extensions are supported (please note that these files are not shown within the disc navigation menu): .srt, .sub, .ssa, .smi • The filename of the movie file has to be repeated at the beginning of the filename for the external subtitle file. • The number of external subtitle files which can be switched for the same movie file is limited to a maximum of 10. DivX video compatibility • Official DivX® Certified product. 7 En • Plays DivX® 5, DivX® 4, DivX® 3 and DivX® VOD video content (in compliance with DivX® Certified technical requirements). • File extensions: .avi and .divx (these must be used for the player to recognize DivX video files). Note that all files with the .avi extension are recognized as MPEG4, but not all of these are necessarily DivX video files and therefore may not be playable on this player. DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc. and are used under license. JPEG file compatibility • Compatible formats: Baseline JPEG and EXIF 2.2* still image files up to a resolution of 3072 x 2048. *File format used by digital still cameras • Progressive JPEG compatible: No • File extensions: .jpg (must be used for the player to recognize JPEG files – do not use for other file types) PC-created disc compatibility Discs recorded using a personal computer may not be playable in this unit due to the setting of the application software used to create the disc. In these particular instances, check with the software publisher for more detailed information. Discs recorded in packet write mode (UDF format) are not compatible with this player. Check the DVD+R/RW, DVD-R/RW or CD-R/ RW software disc boxes for additional compatibility information. 01_DVD-S559_En.book Page 8 Friday, November 18, 2005 4:32 PM Connecting up 02 Chapter 2 English Connecting up Easy connections The setup described here is a basic setup that allows you to play discs using just the cables supplied with the player. In this setup, stereo audio is played through the speakers in your TV. A/V IN TV PB/CB VIDEO L AC IN PCM/q DIGITAL /DTS/MPEG COAXIAL DIGITAL OUT R S VIDEO PR/CR VIDEO OUT Yellow Y COMPONENT AV AUDIO OUT White Red To power outlet Important • This player is equipped with copy protection technology. Do not connect this player to your TV via a VCR using audio/video or S-video cables, as the picture from this player will not appear properly on your TV. (This player may also not be compatible with some combination TV/VCRs for the same reason; refer to the manufacturer for more information.) 8 En 01_DVD-S559_En.book Page 9 Friday, November 18, 2005 4:32 PM 02 Connecting up 1 Connect the VIDEO OUT and AUDIO OUT L/R jacks to a set of A/V inputs on your TV. Use the supplied audio/video cable, connecting the red and white plugs to the audio outputs and the yellow plug to the video output. Make sure you match up the left and right audio outputs with their corresponding inputs for correct stereo sound. See below if you want to use a component or S-video cable for the video connection. Connecting using a SCART AV cable A SCART-type AV connector is provided for connection to a TV or AV receiver. The video output is switchable between ordinary composite and RGB. See AV Connector Out on page 31 for how to set it. The SCART AV connector also outputs analog audio, so there is no need to also connect the AUDIO OUT L/R jacks. 2 Connect the supplied AC power cable to the AC IN inlet, then plug into a power outlet. SCART Note TV • Before unplugging the player from the power outlet, make sure you first switch it into standby using either the front panel STANDBY/ON button, or the remote control, and wait of the -OFF- message to disappear from the player’s display. • For the above reasons, do not plug this player into a switched power supply found on some amplifiers and AV receivers. VIDEO L R UT Y COMPONENT AV AUDIO OUT 1 Use a SCART cable (not supplied) to connect the AV CONNECTOR (RGB) output to a SCART AV input on your TV (or AV receiver). Connecting using the S-video output If your TV (or other equipment) has an S-video (S1) input, you can use the S-video output on this player instead of the standard (composite) output for a better quality picture. • Use an S-video cable (not supplied) to connect the S-VIDEO OUT to an S-video input on your TV (or monitor or AV receiver). Line up the small triangle above the jack with the same mark on the plug before plugging in. 9 En 01_DVD-S559_En.book Page 10 Friday, November 18, 2005 4:32 PM Connecting up 02 Watching progressive scan video from the component video outputs TV VIDEO PB/CB L PCM/q DIGITAL /DTS/MPEG COAXIAL DIGITAL OUT To set up the player for use with a progressive scan TV, see Video Output settings on page 31. When the player is set to output progressive scan video, the PRGSVE indicator lights in the front panel display. R S VIDEO PR/CR VIDEO OUT Y COMPONENT AUDIO OUT Connecting using the component video output You can use the component video output instead of the standard video out jack to connect this player to your TV (or other equipment). This should give you the best quality picture from the three types of video output available. • Use a component video cable (not supplied) to connect the COMPONENT VIDEO OUT jacks to a component video input on your TV, monitor or AV receiver. COMPONENT VIDEO IN TV This player can output progressive scan video from the component video output. Compared to interlace video, progressive scan video effectively doubles the scanning rate of the picture, resulting in a very stable, flicker-free image. English S-VIDEO IN Important • If you connect a TV that is not compatible with a progressive scan signal and switch the player to progressive, you will not be able to see any picture at all. In this case, switch everything off and reconnect using the supplied video cable (see Easy connections on page 8), then switch back to Interlace (see below). Switching the video output to interlace using the front panel controls Switch the player to standby then, using the front panel controls, press STANDBY/ON while pressing  to switch the player back to Interlace. STANDBY/ON PB/CB VIDEO L PCM/q DIGITAL /DTS/MPEG COAXIAL DIGITAL OUT R S VIDEO PR/CR VIDEO OUT Y COMPONENT AUDIO OUT DVD-S559  10 En 01_DVD-S559_En.book Page 11 Friday, November 18, 2005 4:32 PM 02 Connecting up Compatibility of this player with progressive-scan and high-definition TVs This player is compatible with progressive video Macro Vision System Copy Guard. Consumers should note that not all highdefinition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525/625 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output (Interlace). If there are questions regarding our TV set compatibility with this model, please contact our customer service center. This player is fully compatible with the complete line of YAMAHA products, including the projectors DPX-1200, LPX-510 and the plasma monitor PDM-4220. Connecting to an AV receiver To enjoy multichannel surround sound you need to connect this player to an AV receiver using the digital audio output. In addition to a digital connection, we recommend also connecting using the stereo analog connection. You’ll probably also want to connect a video output to your AV receiver. You can use any of the video outputs available on this player (the illustration shows a standard (composite) connection). 1 Connect the DIGITAL AUDIO OUT COAXIAL jack on this player to a coaxial digital input on your AV receiver. DIGITAL IN (COAXIAL) AV receiver VIDEO PB/CB L PCM/q DIGITAL /DTS/MPEG COAXIAL R S VIDEO DIGITAL OUT PR/CR VIDEO OUT Y COMPONENT AUDIO OUT Use a coaxial cable (similar to the supplied video cable) to connect the COAXIAL DIGITAL AUDIO OUT jack to a coaxial input on your AV receiver. 2 Connect the analog AUDIO OUT L/R and VIDEO OUT jacks on this player to a set of analog audio and video inputs on your AV receiver. AUDIO/ VIDEO IN AV receiver PB/CB VIDEO L PCM/q DIGITAL /DTS/MPEG COAXIAL DIGITAL OUT R S VIDEO PR/CR VIDEO OUT Y COMPONENT AUDIO OUT • You can use the SCART AV connector, or the S-video or component video jacks to connect to the AV receiver if you prefer. 11 En 01_DVD-S559_En.book Page 12 Friday, November 18, 2005 4:32 PM Controls and displays 03 Chapter 3 English Controls and displays Front panel 2 1 3 4 5 6 7 8 DVD-S559 1 STANDBY/ON (page 14) 2 Disc tray 3  (page 17) 4  (page 17) 5  and  (page 17) 6  (page 16) 7 Display 8  (page 17) 12 En 01_DVD-S559_En.book Page 13 Friday, November 18, 2005 4:32 PM 03 Controls and displays Remote control 13 ENTER (page 14) 14 CLEAR (page 25) 15 ON SCREEN (page 27) 2 4 3 12 1 2 3 4 5 6 7 8 9 0 CLEAR PLAY MODE SURROUND ENTER ON SCREEN 9 19 ZOOM (page 27) 14 15 22  (PAUSE) (page 17) ENTER HOME MENU 20 and (SLOW/SEARCH) (page 17, 20) 21  (PLAY) (page 17) 16 RETURN 17 SUBTITLE ANGLE ZOOM SKIP 10 11 13 MENU 7 8 17 RETURN (page 14) 18 AUDIO (page 27) TOP MENU MEN 5 6 16 MENU (page 18) OPEN/CLOSE STANDBY/ON 1 AUDIO 18 SLOW/SEARCH STOP PAUSE PLAY 21 Using the remote control 19 20 22 Keep in mind the following when using the remote control: • Make sure that there are no obstacles between the remote and the remote sensor on the unit. • The remote has a range of about 7m. • Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the unit’s remote sensor. 1 (STANDBY/ON) (page 14) 2 Number buttons (page 17) 3 PLAY MODE (page 23) 4 SURROUND (page 28) 5 TOP MENU (page 18) 6 ENTER & cursor buttons (page 14) 7 HOME MENU (page 14) 8 SUBTITLE (page 26) 9 ANGLE (page 27) 10  and  (SKIP) (page 17) 11  (STOP) (page 17) 12 OPEN/CLOSE (page 16) 13 En • Remote controllers for different devices can interfere with each other. Avoid using remotes for other equipment located close to this unit. • Replace the batteries when you notice a fall off in the operating range of the remote. 01_DVD-S559_En.book Page 14 Friday, November 18, 2005 4:32 PM Getting started 04 Chapter 4 Switching on Using the on-screen displays After making sure that everything is connected properly and that the player is plugged in, press STANDBY/ON on the front panel or remote control to switch the player on. For ease of use, this player makes extensive use of graphical on-screen displays (OSDs). Also, switch on your TV and make sure that it is set to the input you connected the DVD player to. All the screens are navigated in basically the same way, using the cursor buttons ( ) to change the highlighted item and pressing ENTER to select it. OPEN/CLOSE STANDBY/ON STANDBY/ON 5 6 7 8 9 0 CLEAR ENTER PLAY MODE SURROUND ON SCREEN TOP MENU MEN MENU ENTER HOME MENU RETURN SUBTITLE DVD-S559 FAQ SKIP ZOOM AUDIO SLOW/SEARCH What it does HOME MENU Display/exit the on-screen display. STOP PAUSE PLAY Changes the highlighted menu item. ENTER Selects the highlighted menu item (both ENTER buttons on the remote work in exactly the same way). RETURN Returns to the main menu without saving changes. Note • This player features a screen saver and an auto power off function. If the player is stopped and no button is pressed for around five minutes, the screen saver starts. If the disc tray is closed but no disc is playing and no control is pressed for about 30 minutes, the player automatically goes into standby. ANGLE Button • My DVD player switches on but there is nothing displayed on my TV. Make sure that the TV is set to the correct video input (not a TV channel). For example, if you connected this player to the VIDEO 1 inputs on your TV, switch your TV to VIDEO 1. English Getting started Note • From here on in this manual, the word ‘select’ generally means use the cursor buttons to highlight an item on-screen, then press ENTER. 14 En 01_DVD-S559_En.book Page 15 Friday, November 18, 2005 4:32 PM 04 Getting started Setting up the player for your TV Setting the language of this player’s on-screen displays If you have a widescreen (16:9) TV, you should setup the player so that the picture will be presented correctly. If you have a conventional (4:3) TV, you can leave the player on the default setting and move on to the next section. This sets the language of the player’s onscreen displays. 1 Press HOME MENU and select ‘Initial Settings’. 1 Press HOME MENU and select ‘Initial Settings’. 2 Select ‘OSD Language’ from the ‘Display’ settings. Initial Settings 2 Select ‘TV Screen’ from the ‘Video Output’ settings. Initial Settings Digital Audio Out TV Screen Component Out Video Output AV Connector Out Language Display Options 4:3 (Letter Box) 4:3 (Pan&Scan) 16:9 (Wide) 3 If you have a widescreen (16:9) TV, select ‘16:9 (Wide)’. If you have a conventional (4:3) TV, you can change the setting from 4:3 (Letter Box) to 4:3 (Pan & Scan) if you prefer. See Video Output settings on page 31 for more details. 4 Press HOME MENU to exit the menu screen. 15 En Initial Settings Initial Settings Digital Audio Out OSD Language Video Output Angle Indicator Language Display Options English français Deutsch Italiano Español 3 Select a language. The on-screen language will change according to your selection. 4 Press HOME MENU to exit the menu screen. 01_DVD-S559_En.book Page 16 Friday, November 18, 2005 4:32 PM Getting started 04 Playing discs For details on playing JPEG picture discs, see Viewing a JPEG slideshow on page 21. English The basic playback controls for playing DVD, CD, Video CD/Super VCD, DivX video and MP3/ WMA discs are covered here. Further functions are detailed in the next chapter. 3 Load a disc. Load a disc with the label side facing up, using the disc tray guide to align the disc (if you’re loading a double-sided DVD disc, load it with the side you want to play face down). Important • Throughout this manual, the term ‘DVD’ means DVD-Video, DVD+R/RW and DVDR/RW. If a function is specific to a particular kind of DVD disc, it is specified. OPEN/CLOSE STANDBY/ON 1 2 3 4 5 6 7 8 9 0 CLEAR PLAY MODE SURROUND ENTER ON SCREEN TOP MEN MENU 4 Press  (play) to start playback. If you’re playing a DVD or Video CD/Super VCD, an on-screen menu may appear. See DVDVideo disc menus on page 18 and Video CD/ Super VCD PBC menus on page 18 for more on how to navigate these. • If you’re playing a containing DivX video files or MP3/WMA audio files, it may take a few seconds before playback starts, etc. This is normal. MENU Note ENTER HOME MENU RETURN SUBTITLE ANGLE SKIP ZOOM AUDIO SLOW/SEARCH STOP PAUSE PLAY • You may find with some DVD discs that some playback controls don’t work in certain parts of the disc. This is not a malfunction. • If a disc contains a mixture of DivX video and other media file types (MP3, for example), first select whether to play the DivX video files (DivX)or the other media file types (MP3 / WMA / JPEG) from the on-screen display. 1 If the player isn’t already on, press (STANDBY/ON) to switch it on. If you’re playing a DVD, disc containing DivX video files or Video CD/Super VCD, also turn on your TV and make sure that it is set to the correct video input. 2 Press OPEN/CLOSE () to open the disc tray. 16 En 01_DVD-S559_En.book Page 17 Friday, November 18, 2005 4:32 PM 04 Getting started Basic playback controls Resume and Last Memory The table below shows the basic controls on the remote for playing discs. The following chapter covers other playback features in more detail. When you stop playback of a DVD, CD, Video CD/Super VCD or DivX video discs, RESUME is shown in the display indicating that you can resume playback again from that point. Button What it does  Starts playback. If the display shows RESUME or LAST MEM playback starts from the resume or last memory point (see also Resume and Last Memory below.)  Pauses a disc that’s playing, or restarts a paused disc.  Stops playback. See also Resume and Last Memory below. (remote only) Press to start fast reverse scanning. Press  (play) to resume normal playback. (remote only) Press to start fast forward scanning. Press  (play) to resume normal playback.  Skips to the start of the current track, title or chapter, then to previous tracks/titles/chapters.  Skips to the next track, title or chapter. Numbers Use to enter a title/chapter/track (remote number. Press ENTER to select. only) • If the disc is stopped, playback starts from the selected title (for DVD) or track (for CD/Video CD/ Super VCD). • If the disc is playing, playback jumps to the start of the selected title (VR mode DVD-RW), chapter (DVD-Video) or track (CD/Video CD/ Super VCD). 17 En If the disc tray is not opened, the next time you start playback the display shows RESUME and playback resumes from the resume point. (If you want to clear the resume point, press  (stop) while RESUME is displayed.) With DVDs and Video CD/ Super VCDs, if you take the disc out of the player after stopping playback, the last play position is stored in memory. If the next disc you load is the same one, the display shows LAST MEM and playback will resume. For DVD-Video discs, the player stores the play position of the last five discs. When one of these discs is next loaded, you can resume playback. Note • The Last Memory function doesn’t work with VR format DVD-RW discs. • If you don’t need the Last Memory function when you stop a disc, you can press OPEN/ CLOSE () to stop playback and open the disc tray. 01_DVD-S559_En.book Page 18 Friday, November 18, 2005 4:32 PM Getting started 04 Video CD/Super VCD PBC menus Many DVD-Video discs feature menus from which you can select what you want to watch. They may also give access to additional features, such as subtitle and audio language selection, or special features such as slideshows. See the disc packaging for details. Some Video CD/Super VCDs have menus from which you can choose what you want to watch. These are called PBC (Playback control) menus. Sometimes DVD-Video menus are displayed automatically when you start playback; others only appear when you press MENU or TOP MENU. You can play a PBC Video CD/Super VCD without having to navigate the PBC menu by starting playback using a number button to select a track, rather than the  (play) button. 1 3 2 6 5 0 9 2 3 5 6 7 8 9 0 CLEAR ENTER PLAY MODE SURROUND 8 CLEAR 4 ON SCREEN TOP MEN MENU ENTER MENU ON SCREEN TOP MEN MENU ENTER HOME MENU MENU RETURN SUBTITLE ENTER HOME MENU 1 4 7 PLAY MODE SURROUND OPEN/CLOSE STANDBY/ON OPEN/CLOSE STANDBY/ON ANGLE ZOOM AUDIO RETURN SKIP SUBTITLE ANGLE ZOOM SLOW/SEARCH AUDIO STOP SKIP PAUSE PLAY SLOW/SEARCH STOP PAUSE PLAY Button What it does TOP MENU Displays the ‘top menu’ of a DVD disc—this varies with the disc. RETURN Displays the PBC menu. MENU Displays a DVD disc menu—this varies with the disc and may be the same as the ‘top menu’. Numbers (remote only) Use to enter a numbered menu option. Press ENTER to select. Moves the cursor around the screen.  Displays the previous menu page (if there is one). ENTER Selects the current menu option.  RETURN Returns to the previously displayed menu screen. Displays the next menu page (if there is one). Numbers (remote only) Highlights a numbered menu option (some discs only). Press ENTER to select. Button English DVD-Video disc menus What it does 18 En 01_DVD-S559_En.book Page 19 Friday, November 18, 2005 4:32 PM 04 Getting started FAQ • After I load a DVD disc, it ejects automatically after a few seconds! Most likely, the disc is the wrong region for your player. The region number should be printed on the disc; check it against the region number of the player (which you can find on the rear panel). See also DVD-Video regions on page 37. If the region number is OK, it may be that the disc is damaged or dirty. Clean the disc and look for signs of damage. See also Taking care of your player and discs on page 35. • Why won’t the disc I loaded play? First check that you loaded the disc the right way up (label side up), and that it’s clean and undamaged. See Taking care of your player and discs on page 35 for information on cleaning discs. If a disc loaded correctly won’t play, it’s probably an incompatible format or disc type, such as DVD-Audio or DVD-ROM. See Disc/content format playback compatibility on page 5 for more on disc compatibility. • I have a widescreen TV so why are there black bars at the top and bottom of the screen when I play some discs? Some movie formats are such that even when played on a widescreen TV, black bars are necessary at the top and bottom of the screen. This is not a malfunction. • I have a standard (4:3) TV and set the player to show widescreen DVDs in pan & scan format, so why do I still get black bars top and bottom with some discs? Some discs override the display preferences of the player, so even if you have 4:3 (Pan & Scan) selected, those discs will still be shown in letter box format. This is not a malfunction. 19 En 01_DVD-S559_En.book Page 20 Friday, November 18, 2005 4:32 PM Playing discs 05 Chapter 5 Note • Many of the functions covered in this chapter apply to DVD discs, Video CDs/ Super VCDs, CDs, DivX video and WMA/ MP3 JPEG discs, although the exact operation of some varies slightly with the kind of disc loaded. Playing in slow motion You can play DVDs at four different slow motion speeds, forwards and backwards. Video CD/Super VCDs and DivX video can be played at four different forward slow motion speeds. 1 During playback, press  (pause). • Some DVDs restrict the use of some functions (random or repeat, for example) in some or all parts of the disc. This is not a malfunction. 2 Press and hold or until slow motion playback starts. • The slow motion speed is shown onscreen. • When playing Video CD/Super VCDs, some of the functions are not available during PBC playback. If you want to use them, start the disc playing using a number button to select a track. • There is no sound during slow motion playback. Scanning discs You can fast-scan discs forward or backward at four different speeds (DivX video only one speed). English Playing discs 3 Press repeatedly to change the slow motion speed. 4 To resume normal playback, press  (play). • Depending on the disc, normal playback may automatically resume when a new chapter is reached. 1 During playback, press or to start scanning. • There is no sound while scanning DVDs, DivX video and Video CD/Super VCDs. 2 Press repeatedly to increase the scanning speed. • The scanning speed is shown on-screen except when playing a WMA/MP3 track using the Disc Navigator. 3 To resume normal playback, press  (play). • When scanning a Video CD/Super VCD playing in PBC mode or a WMA/MP3 track, playback automatically resumes at the end or beginning of the track. • Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc. 20 En 01_DVD-S559_En.book Page 21 Friday, November 18, 2005 4:32 PM 05 Playing discs Frame advance/frame reverse Button What it does You can advance or back up DVD discs frameby-frame. With Video CD/Super VCDs and DivX video file you can only use frame advance. ZOOM Pauses the slideshow and zooms the picture. Press again to toggle between 1x, 2x and 4x zoom. (Press  (play) to restart slideshow). MENU Displays the Disc Navigator screen (see below). 1 During playback, press  (pause). 2 Press or to reverse or advance a frame at a time. 3 To resume normal playback, press  (play). • Depending on the disc, normal playback may automatically resume when a new chapter is reached. Viewing a JPEG slideshow After loading a CD/CD-R/RW containing JPEG picture files, press  (play) to start a slideshow from the first folder/picture on the disc. The player displays the pictures in each folder in alphabetical order. Note • The time it takes for the player to load a file increases with large file sizes. Browsing DVD or Video CD/ Super VCD disc with the Disc Navigator Use the Disc Navigator to browse through the contents of a DVD or Video CD/Super VCD disc to find the part you want to play. Pictures are automatically adjusted so that they fill as much of the screen as possible (if the aspect ratio of the picture is different to your TV screen you may notice black bars at the sides, or at the top and bottom of the screen). While the slideshow is running: Button What it does  Pauses the slideshow; press again to restart.  Displays the previous picture.  Displays the next picture. Pauses the slideshow and rotates the displayed picture 90º (counter) clockwise. (Press  (play) to restart slideshow). Pauses the slideshow and flips the displayed picture horizontally or vertically. (Press  (play) to restart slideshow). 21 En Important • You can’t use the Disc Navigator with Video CD/Super VCDs in PBC mode. 1 During playback, press HOME MENU and select ‘Disc Navigator’ from the onscreen menu. Disc Navigator 2 Select a view option. Disc Navigator Title Chapter 01_DVD-S559_En.book Page 22 Friday, November 18, 2005 4:32 PM Playing discs 05 The options available depend on the kind of disc loaded and whether the disc is playing or not, but include: • Chapter – Chapters from the current title of a DVD-Video disc. • Track – Tracks from a Video CD/Super VCD disc. • Time – Thumbnails from a Video CD/Super VCD disc at 10 minute intervals. • Original: Title – Original titles from a VR mode DVD-RW disc. • Playlist: Title – Playlist titles from a VR mode DVD-RW disc. • Original: Time – Thumbnails from the Original content at 10 minute intervals. • Playlist: Time – Thumbnails from the Playlist at 10 minute intervals. The screen shows up to six moving thumbnail images displayed one after another. To display the previous/next six thumbnails, press /  (you don’t have to wait for all the thumbnails to finish playing to display the previous/next page). 3 Select the thumbnail image for what you want to play. 01 02 03 • Another way to find a particular place on a disc is to use one of the search modes. See Searching a disc on page 26. Browsing WMA, MP3, DivX video and JPEG files with the Disc Navigator Use the Disc Navigator to find a particular file or folder by filename. Note that if there are other types of files on the same disc, these will not be displayed in the Disc Navigator. 1 Press HOME MENU and select ‘Disc Navigator’ from the on-screen menu. 00:00/ 00:00 0kbps Folder1 Folder2 Folder3 Folder4 2 Use the cursor buttons ( ) and ENTER to navigate. Use the cursor up/down buttons ( ) to move up and down the folder/file list. Use the cursor left button ( parent folder. 04 05 06 Disc Navigator: Title 01- 49: - - English • Title – Titles from a DVD-Video disc. Tip Use ENTER or cursor right ( highlighted folder. ) to return to the ) to open a • You can also return to the parent folder by going to the top of the list to the ‘..’ folder, then pressing ENTER. You can use either the cursor buttons ( ) and ENTER to select a thumbnail, or the number buttons. To select using the number buttons, enter a two-digit number then press ENTER. 22 En 01_DVD-S559_En.book Page 23 Friday, November 18, 2005 4:32 PM 05 Playing discs • When a JPEG file is highlighted, a thumbnail image is displayed on the right. 00:00/ 00:00 1 During playback, press PLAY MODE and select ‘A-B Repeat’ from the list of functions on the left. 0kbps Play Mode Folder 2 File1 File2 File3 File4 File5 3 To play the highlighted track or DivX video file or display the highlighted JPEG file, press ENTER. • When a WMA/MP3 or DivX video file is selected, playback begins, starting with the selected file, and continues until the end of the folder. • When a JPEG file is selected, a slideshow begins, starting with that file, and continues to the end of the folder. When the slideshow comes to the end of the foloder, it automatically continues to the begining of the foloder. Tip • To play the contents of the whole disc rather than just the current folder, exit the Disc Navigator and start playback using the  (play) button. Looping a section of a disc The A-B Repeat function allows you to specify two points (A and B) within a track (CD, Video CD/Super VCD) or title (DVD) that form a loop which is played over and over. • You can’t use A-B Repeat with Video CD/ Super VCDs in PBC mode, or WMA/MP3/ DivX video files. 23 En A-B Repeat Repeat Random Program Search Mode A(Start Point) B(End Point) Off 2 Press ENTER on ‘A(Start Point)’ to set the loop start point. 3 Press ENTER on ‘B(End Point)’ to set the loop end point. After pressing ENTER, playback jumps back to the start point and plays the loop. 4 To resume normal playback, select ‘Off’ from the menu. Using repeat play There are various repeat play options, depending on the kind of disc loaded. It’s also possible to use repeat play together with program play to repeat the tracks/chapters in the program list (see Creating a program list on page 25). Important • You can’t use Repeat play with Video CD/ Super VCDs in PBC mode, or with WMA/ MP3 discs. • You can’t use repeat and random play at the same time. 05_playing_discs.fm Page 24 Tuesday, November 22, 2005 9:10 AM Playing discs 1 During playback, press PLAY MODE and select ‘Repeat’ from the list of functions on the left. Repeat Random Program Search Mode Title Repeat Chapter Repeat Repeat Off 2 Select a repeat play option. If program play is active, select Program Repeat to repeat the program list, or Repeat Off to cancel. The repeat options available depend on the kind of disc loaded. For example, for DVD discs, you can select Title Repeat or Chapter Repeat (or Repeat Off). Play Mode A-B Repeat Repeat Random Program Search Mode Title Repeat Chapter Repeat Repeat Off • For CDs and Video CD/Super VCDs, select Disc Repeat or Track Repeat (or Repeat Off). • For DivX video discs, select Title Repeat (or Repeat Off). Using random play Use the random play function to play titles or chapters (DVD-Video), or tracks (CD, Video CD/ Super VCD) at random. (Note that the same track/title/chapter may play more than once.) Important • Random play remains in effect until you select Random Off from the random play menu options. • You can’t use random play with VR format DVD-RW discs, Video CD/Super VCDs playing in PBC mode, WMA/MP3 discs, DivX video discs, or while a DVD disc menu is being displayed. English Play Mode A-B Repeat 05 • You can't use random play together with program or repeat play. 1 Press PLAY MODE and select ‘Random’ from the list of functions on the left. Play Mode A-B Repeat Repeat Random Program Search Mode Random Title Random Chapter Random Off 2 Select a random play option. The random play options available depend on the kind of disc loaded. For example, for DVD discs, you can select Random Title or Random Chapter (or Random Off). Play Mode A-B Repeat Repeat Random Program Random Title Random Chapter Random Off Search Mode • For CDs and Video CD/Super VCDs, select On or Off to switch random play on or off. You can set the random play option when a disc is playing or stopped. 24 En 01_DVD-S559_En.book Page 25 Friday, November 18, 2005 4:32 PM 05 Playing discs Tip • Use the following controls during random play: Button What it does  Selects a new track/title/chapter at random.  Returns to the beginning of the current track/title/chapter. Creating a program list This feature lets you program the play order of titles/chapters/tracks on a disc. Important • You can’t use Program play with VR format DVD-RW discs, Video CD/Super VCDs playing in PBC mode, WMA/MP3 discs, DivX video discs, or while a DVD disc menu is being displayed. 1 Press PLAY MODE and select ‘Program’ from the list of functions on the left. Play Mode A-B Repeat Repeat Random Program Search Mode Create/Edit Playback Start Playback Stop Program Delete 2 Select ‘Create/Edit’ from the list of program options. 25 En 3 Use the cursor buttons and ENTER to select a title, chapter or track for the current step in the program list. For a DVD disc, you can add a title or a chapter to the program list. Program Program Step Title 1~38 Chapter 1~004 01. 01 02. 03. 04. 05. 06. 07. 08. Title 01 Title 02 Title 03 Title 04 Title 05 Title 06 Title 07 Title 08 Chapter 001 Chapter 002 Chapter 003 Chapter 004 • For a CD or Video CD/Super VCD, select a track to add to the program list. After pressing ENTER to select the title/ chapter/track, the step number automatically moves down one. 4 Repeat step 3 to build up a program list. A program list can contain up to 24 titles/ chapters/tracks. • You can insert steps into the middle of a program list by just highlighting the position where you want the new step to appear and entering a title/chapter/track number. • To delete a step, highlight it and press CLEAR. 5 To play the program list, press  (play). Program play remains active until you turn off program play (see below), erase the program list (see below), eject the disc or switch off the player. 01_DVD-S559_En.book Page 26 Friday, November 18, 2005 4:32 PM Playing discs 05 3 Use the number buttons to enter a title, chapter or track number, or a time. Tip Button Play Mode A-B Repeat Repeat Random Program What it does PLAY MODE Save the program list and exit the program edit screen without starting playback (HOME MENU does the same).  Skip to the next step in the program list. • Playback Start – Starts playback of a saved program list • Playback Stop – Turns off program play, but does not erase the program list • Program Delete – Erases the program list and turns off program play Searching a disc You can search DVD discs by title or chapter number, or by time; CDs and Video CD/Super VCDs by track number or time; DivX video discs by time. Important • Search functions are not available with Video CD/Super VCDs in PBC mode, or with WMA/MP3 discs. 1 Press PLAY MODE and select ‘Search Mode’ from the list of functions on the left. 2 Select a search mode. The search options available depend on the kind of disc loaded. Input Chapter Time Search 0 0 1 Search Mode • For a time search, enter the number of minutes and seconds into the currently playing title (DVD/ DivX video) or track (CD/ Video CD/Super VCD) you want playback to resume from. For example, press 4, 5, 0, 0 to have playback start from 45 minutes into the disc. For 1 hour, 20 minutes and 30 seconds, press 8, 0, 3, 0. Other functions available from the program menu There are a number of other options in the program menu in addition to Create/Edit. Title Search Chapter Search English • Use the following controls during program play: 4 Press ENTER to start playback. Switching subtitles Some DVD and DivX video discs have subtitles in one or more languages; the disc box will usually tell you which subtitle languages are available. You can switch subtitle language during playback. 1 Press SUBTITLE repeatedly to select a subtitle option. Current / Total Subtitle 1/ 2 English Note • Some discs only allow you to change subtitle language from the disc menu. Press TOP MENU or MENU to access. • To set subtitle preferences, see Subtitle Language on page 31. • See Displaying DivX subtitle files on page 7 for more on DivX subtitles. • The disc must be playing in order to use time search. 26 En 01_DVD-S559_En.book Page 27 Friday, November 18, 2005 4:32 PM 05 Playing discs Switching audio language/ channels When playing a DVD and DivX video disc recorded with dialog in two or more languages, you can switch audio language during playback. When playing a VR format DVD-RW disc recorded with dual-mono audio, you can switch between the main, sub, and mixed channels during playback. When playing a Video CD/Super VCD, you can switch between stereo, just the left channel or just the right channel. 1 Press AUDIO repeatedly to select an audio language/channel option. The language/channel information is shown on-screen. Note • Some DVD discs only allow you to change audio language from the disc menu. Press TOP MENU or MENU to access. • To set DVD audio language preferences, see Language settings on page 31. Zooming the screen Using the zoom feature you can magnify a part of the screen by a factor of 2 or 4, while watching a DVD, DivX video title or Video CD/ Super VCD or playing a JPEG disc. 1 During playback, use the ZOOM button to select the zoom factor (Normal, 2x or 4x). • Since DVD, Video CD/Super VCD, DivX video title and JPEG pictures have a fixed resolution, picture quality will deteriorate, especially at 4x zoom. This is not a malfunction. 2 Use the cursor buttons to change the zoomed area. You can change the zoom factor and the zoomed area freely during playback. 27 En • If the navigation square at the top of the screen disappears, press ZOOM again to display it. Switching camera angles Some DVD discs feature scenes shot from two or more angles—check the disc box for details. When a multi-angle scene is playing, a icon appears on screen to let you know that other angles are available (this can be switched off if you prefer—see Display settings on page 32). 1 During playback (or when paused), press ANGLE to switch angle. Displaying disc information Various track, chapter and title information, such as the elapsed and remaining playing time can be displayed on-screen while a disc is playing. 1 To show/switch/hide the information displayed, press ON SCREEN repeatedly. • When a disc is playing, the information appears at the top of the screen. Keep pressing ON SCREEN to change the displayed information. 01_DVD-S559_En.book Page 28 Friday, November 18, 2005 4:32 PM Audio Settings and Video Adjust menus 06 Chapter 6 Audio Settings menu The Audio Settings menu offers features for adjusting the way discs sound. 1 Press HOME MENU and select ‘Audio Settings’ from the on-screen display. English Audio Settings and Video Adjust menus • Audio DRC is only effective through the digital output when Digital Out is set to On, and Dolby Digital Out is set to Dolby Digital > PCM (see Digital Audio Out settings on page 30). • The effect of Audio DRC also depends on your speakers and AV receiver settings. Audio Settings 2 Select and change settings using the cursor buttons ( ), and ENTER. Audio Settings Equalizer Virtual Surround Audio DRC Dialog Virtual Surround • Settings: On, Off (default) Switch on Virtual Surround to enjoy realistic surround sound effects from just two speakers. On Off Tip • You can also use the SURROUND button on the remote control to switch Virtual Surround on. Audio DRC • Settings: High, Medium, Low, Off (default) When watching Dolby Digital DVDs at low volume, it’s easy to lose the quieter sounds completely—including some of the dialog. Switching Audio DRC (Dynamic Range Control) to on can help by bringing up the quieter sounds, while controlling loud peaks. How much of a difference you hear depends on the material you’re listening to. If the material doesn’t have wide variations in volume, you may not notice much change. Note • Audio DRC is only effective with Dolby Digital audio sources. Note • Virtual Surround doesn’t work with DTS, through either the analog or digital outputs. • 96kHz linear PCM audio is automatically downsampled to 48kHz if Virtual Surround is switched on. • If the player is outputting Dolby Digital, DTS or MPEG bitstream audio (in other words, no conversion to PCM), Virtual Surround has no effect on the audio from the digital output. See Digital Audio Out settings on page 30 for how to set up the digital output formats. • How good the surround effect is varies with the disc. 28 En 01_DVD-S559_En.book Page 29 Friday, November 18, 2005 4:32 PM 06 Audio Settings and Video Adjust menus Dialog • Settings: High, Medium, Low, Off (default) The Dialog feature is designed to make the dialog stand out from other background sounds in the soundtrack. Equalizer • Settings: Rock, Pop, Live, Dance, Techno, Classic, Soft, Off (default) The various preset EQ curves are designed to suit various styles of music. • Contrast – Adjusts the contrast between light and dark (–16 to +16). • Gamma – Adjusts the ‘warmth’ of the picture (High, Medium, Low, Off (default)). • Hue – Adjusts the red/green balance (Green 9 to Red 9). • Chroma Level – Adjusts how saturated colors appear (–9 to +9). Adjust the Brightness, Contrast, Hue and Chroma Level settings using the cursor left/ right ( ) buttons. Brightness min max 0 Note • 96kHz linear PCM audio is automatically downsampled to 48kHz if the Equalizer is switched on. Video Adjust menu From the Video Adjust screen you can adjust various settings that affect how the picture is presented. 1 Press HOME MENU and select ‘Video Adjust’ from the on-screen display. Video Adjust 2 ( Make settings using the cursor buttons ), and ENTER. Video Adjust Sharpness Brightness Contrast Gamma Hue Chroma Level       Standard 0 0 Off 0 0 You can adjust the following picture quality settings: • Sharpness – Adjusts the sharpness of edges in the picture (Fine, Standard (default), Soft). • Brightness – Adjusts the overall brightness (–20 to +20). 29 En 3 Press ENTER to return to the Video Adjust screen, or HOME MENU to exit. 01_DVD-S559_En.book Page 30 Friday, November 18, 2005 4:32 PM Initial Settings menu 07 Chapter 7 Using the Initial Settings menu The Initial Settings menu provides audio and video output settings, parental lock settings, and display settings, among others. Note If an option is grayed out it means that it cannot be changed at the current time. This is usually because a disc is playing. Stop the disc, then change the setting. 1 Press HOME MENU and select ‘Initial Settings’. Initial Settings 2 Use the cursor buttons and ENTER to select the setting and option you want to set. All the settings and options are explained on the following pages. English Initial Settings menu • In the table below, the default setting is shown in bold: other settings are shown in italics. • The Digital Audio Out settings only need to be set if you have connected the digital output of this player to an AV receiver, or other equipment. • Check the owner’s manual supplied with your other equipment to see which digital audio formats it’s compatible with. • Some settings, such as TV Screen, Audio Language and Subtitle Language may be overridden by the DVD disc. Often these settings can also be made from the DVD disc menu. Digital Audio Out settings Setting Option What it means Digital Out On Digital audio is output from the digital outputs. Off No digital audio output. Dolby Digital Dolby Digital encoded digital audio is output when playing a Dolby Digital DVD disc. Dolby Digital > PCM Dolby Digital audio is converted to PCM audio before being output. DTS DTS encoded digital audio is output when playing a DTS disc. (Noise will be output if your amplifier/receiver is not compatible with DTS audio.) Off No digital audio is output when playing a DTS disc. 96kHz > 48kHz 96kHz digital audio is converted to 48kHz for digital output. 96kHz 96kHz digital audio is output as is at 96kHz. Dolby Digital Out DTS Out 96 kHz PCM Out 30 En 01_DVD-S559_En.book Page 31 Friday, November 18, 2005 4:32 PM 07 Initial Settings menu Setting Option What it means MPEG Out MPEG > PCM MPEG encoded digital audio is converted to PCM audio for digital output. MPEG MPEG encoded digital audio is output as is. Video Output settings Setting Option What it means TV Screen (See also Screen sizes and disc formats on page 36.) 4:3 (Letter Box) Set if you have a conventional 4:3 TV. Widescreen movies are shown with black bars top and bottom. 4:3 (Pan & Scan) Set if you have a conventional 4:3 TV. Widescreen movies are shown with the sides cropped so that the image fills the screen. 16:9 (Wide) Set if you have a widescreen TV. Interlace Set if your TV is not compatible with progressive scan video. Progressive Set if your TV is compatible with progressive scan video (see your TV’s instruction manual for details). See also Switching the video output to interlace using the front panel controls on page 10. Note that progressive scan video is only output from the component video jacks. Video Ordinary (composite) video output, compatible with all TVs. RGB If your TV is compatible, this setting gives the best picture quality. Note that there is no output from the component jacks when this setting selected. Component Out AV Connector Out Language settings Setting Option What it means Audio Language English If there is an English soundtrack on the disc then it will be played. Languages as displayed If there is the language selected on the disc, then it will be played. Other Language Select to choose a language other than the ones displayed (see page 37). Subtitle Language English (See also Displaying DivX subtitle files on page 7.) If there are English subtitles on the disc then they will be displayed. Languages as displayed If there is the subtitle language selected on the disc, then it will be displayed. Other Language 31 En Select to choose a language other than the ones displayed (see page 37). 01_DVD-S559_En.book Page 32 Friday, November 18, 2005 4:32 PM Initial Settings menu 07 Option What it means DVD Menu Lang. w/Subtitle Lang. DVD disc menus will be displayed in the same language as your selected subtitle language, if possible. Languages as displayed DVD disc menus will be displayed in the selected language, if possible. Subtitle Display Other Language Select to choose a language other than the ones displayed (see page 37). On Subtitles are displayed according to your selected subtitle language (see above). Off Subtitles are always off by default when you play a DVD disc (note that some discs override this setting). English Setting Display settings Setting Option What it means OSD Language English On-screen displays of the player are in English. Languages as displayed On-screen displays are shown in the language selected. Angle Indicator On A camera icon is displayed on-screen during multi-angle scenes on a DVD disc. Off No multi-angle indication is shown. Options settings Setting Option What it means Parental Lock – See Parental Lock on page 33. DivX VOD Display See About DivX® VOD content on page 34. 32 En 01_DVD-S559_En.book Page 33 Friday, November 18, 2005 4:32 PM 07 Initial Settings menu Parental Lock 1 Select ‘Password Change’. • Default level: Off; Default password: none; Default Country/Area code: us (2119) 2 Use the number buttons to enter your existing password, then press ENTER. To give you some control over what your children watch on your DVD player, some DVDVideo discs feature a Parental Lock level. If your player is set to a lower level than the disc, the disc won’t play. 3 Enter a new password and press ENTER. This registers the new password and you will return to the Options menu screen. Some discs also support the Country/Area Code feature. The player does not play certain scenes on these discs, depending on the Country/Area Code you set. Note Setting/changing the Parental Lock 1 2 Use number buttons to enter your password, then press ENTER. 3 • Not all discs use Parental Lock, and will play without requiring the password first. • If you forget your password, you’ll need to reset the player to register a new password. (see Resetting the player on page 37) Select ‘Level Change’. Select a new level and press ENTER. • Press the cursor left ( ) repeatedly to lock more levels (more discs will require the password); press the cursor right ( ) to unlock levels. You can’t lock level 1. This sets the new level and you will return to the Options menu screen. Registering a new password You must register a password before you can change the Parental Lock level or enter a Country code. 1 Select ‘Options’, then ‘Password’. Setting/changing the Country/Area code You can find the Country/Area code list on page 38. 1 Initial Settings Digital Audio Out Parental Lock Video Output DivX VOD Language Display Options Password Level Change Country Code 2 Use the number buttons to enter a 4digit password. The numbers you enter show up as asterisks (*) on-screen. 3 Press ENTER to register the password. You will return to the Options menu screen. Changing your password To change your password, confirm your existing password then enter a new one. 33 En Select ‘Country Code’. 2 Use number buttons to enter your password, then press ENTER. 3 Select a Country/Area code and press ENTER. There are two ways you can do this: • Select by code letter: Use the cursor up/ down ( ) to change the Country/Area code. • Select by code number: Press the cursor right ( ) then use the number buttons to enter the 4-digit Country/Area code. The new Country/Area code is set and you will return to the Options menu screen. Note that the new Country/Area code doesn’t take effect until the next disc is loaded (or the current disc is reloaded). 01_DVD-S559_En.book Page 34 Friday, November 18, 2005 4:32 PM Initial Settings menu About DivX® VOD content 3 Select ‘Display’. Your 8-digit registration code is displayed. Initial Settings Digital Audio Out DivX VOD Registration Code Video Output Language 01234567 Display Options English In order to play DivX VOD (video on demand) content on this player, you first need to register the player with your DivX VOD content provider. You do this by generating a DivX VOD registration code, which you submit to your provider. 07 Important • DivX VOD content is protected by a DRM (Digital Rights Management) system. This restricts playback of content to specific, registered devices. • If you load a disc that contains DivX VOD content not authorized for your player, the message Authorization Error is displayed and the content will not play. • Resetting the player (page 37) will not cause you to lose your registration code. Displaying your DivX VOD registration code 1 Press HOME MENU and select ‘Initial Settings’. 2 Select ‘Options’, then ‘DivX VOD’. Initial Settings Digital Audio Out Parental Lock Video Output DivX VOD Language Display Make a note of the code as you will need it when you register with a DivX VOD provider. Playing DivX® VOD content Some DivX VOD content may only be playable a fixed number of times. When you load a disc containing this type of DivX VOD content, the remaining number of plays is shown on-screen and you then have the option of playing the disc (thereby using up one of the remaining plays), or stopping. If you load a disc that contains expired DivX VOD content (for example, content that has zero remaining plays), the message Rental Expired is displayed. If your DivX VOD content allows an unlimited number of plays, then you may load the disc into your player and play the content as often as you like, and no message will be displayed. Display Options 34 En 01_DVD-S559_En.book Page 35 Friday, November 18, 2005 4:32 PM 08 Additional information Chapter 8 Additional information Taking care of your player and discs General Cleaning discs Fingerprints and dust on discs can affect playback performance. Clean using a soft, dry cloth, wiping the disc lightly from the center to the outside edge as shown below. Hold discs by the edge or by the center hole and edge. When you're not using a disc, return it to its case and store upright. Avoid leaving discs in excessively cold, humid, or hot environments (including under direct sunlight). Don't glue paper or put stickers on to discs. Do not use a pencil, ball-point pen or other sharptipped writing instrument to write on the disc. Don’t use self-adhesive disc labels on discs as these can cause the disc to warp slightly during playback causing distortion in the picture and/or sound. Damaged and shaped discs Do not use cracked, chipped, warped, or otherwise damaged discs as they may damage the player. If necessary, use a cloth soaked in alcohol, or a commercially available CD/DVD cleaning kit to clean a disc more thoroughly. Never use benzine, thinner or other cleaning agents, including products designed for cleaning vinyl records. Cleaning the unit’s exterior Unplug the unit before cleaning. Use a dry cloth to wipe off dust and dirt. If the surfaces are very dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water and wrung out well, then wipe again with a dry cloth. Do not use furniture wax or cleaners. Never use thinners, benzine or insecticide sprays or other chemicals on or near this unit. If you use a chemical-impregnated cleaning cloth, read the instructions carefully before use. These cloths may leave smear marks on half-mirror finish surfaces; if this happens, finish with a dry cloth. This player is designed to be used only with conventional, fully circular discs. Do not use shaped discs. YAMAHA disclaims all liability arising in connection with the use of shaped discs. 35 En 01_DVD-S559_En.book Page 36 Friday, November 18, 2005 4:32 PM Additional information Cleaning the pickup lens Condensation Condensation may form inside the player if it is brought into a warm room from outside, or if the temperature of the room rises quickly. Although the condensation won’t damage the player, it may temporarily impair its performance. Leave it to adjust to the warmer temperature for about an hour before switching on. Please note that some movie aspect ratios are wider than 16:9, so even though you have a widescreen TV, these discs will still play in a ‘letter box’ style with black bars at the top and bottom of the screen. Standard TV users English The DVD player’s lens should not become dirty in normal use, but if for some reason it should malfunction due to dust or dirt, consult your nearest YAMAHA authorized service center. We do not recommend using commercially available lens cleaners for CD players. 08 If you have a standard TV, the TV Screen setting (page 31) of this player should be set to 4:3 (Letter Box) or 4:3 (Pan&Scan), depending on which you prefer. Set to 4:3 (Letter Box), widescreen discs are shown with black bars top and bottom. Moving the player If you need to move the player, first press STANDBY/ON on the front panel to turn the player off. Wait for -OFF- to disappear from the display, then unplug the power cable. Never lift or move the unit during playback—discs rotate at a high speed and may be damaged. Set to 4:3 (Pan&Scan), widescreen discs are shown with the left and right sides cropped. Although the picture looks larger, you don’t actually see the whole picture. Screen sizes and disc formats DVD-Video discs come in several different screen aspect ratios, ranging from TV programs, which are generally 4:3, to CinemaScope widescreen movies, with an aspect ratio of up to about 7:3. Televisions, too, come in different aspect ratios; ‘standard’ 4:3 and widescreen 16:9. Please note that many widescreen discs override the player’s settings so that the disc is shown in letter box format regardless of the setting. Note Widescreen TV users If you have a widescreen TV, the TV Screen setting (page 31) of this player should be set to 16:9 (Wide). • Using the 16:9 (Wide) setting with a standard 4:3 TV, or either of the 4:3 settings with a widescreen TV, will result in a distorted picture. When you watch discs recorded in 4:3 format, you can use the TV controls to select how the picture is presented. Your TV may offer various zoom and stretch options; see the instructions that came with your TV for details. 36 En 01_DVD-S559_En.book Page 37 Friday, November 18, 2005 4:32 PM 08 Additional information Setting the TV system The default setting of this player is AUTO, and unless you notice that the picture is distorted when playing some discs, you should leave it set to AUTO. If you experience picture distortion with some discs, set the TV system to match your country or region’s system. Doing this, however, may restrict the kinds of disc you can watch. The table below shows what kinds of disc are compatible with each setting (AUTO, PAL and NTSC). 1 If the player is on, press STANDBY/ON to switch it to standby. 2 Using the front panel controls, hold down  then press STANDBY/ON to switch the TV system. The TV system changes as follows: • AUTO DVD-Video regions All DVD-Video discs carry a region mark on the case somewhere that indicates which region(s) of the world the disc is compatible with. Your DVD player also has a region mark, which you can find on the rear panel. Discs from incompatible regions will not play in this player. Discs marked ALL will play in any player. The diagram below shows the various DVD regions of the world. NTSC • NTSC • PAL 2 Using the front panel buttons, hold down the  (stop) button and press STANDBY/ON to switch the player back on. All the player’s settings are now reset. 1 PAL 5 2 AUTO 6 4 Note 2 • You have to switch the player into standby (press STANDBY/ON) before each change. Disc Player setting Type Format NTSC PAL AUTO DVD/Super VCD/ Video CD/DivX Video NTSC NTSC PAL NTSC PAL NTSC PAL PAL — NTSC PAL NTSC or PAL CD/MP3/WMA/ JPEG no disc Resetting the player Use this procedure to reset all the player’s settings to the factory default. 1 37 En 5 Switch the player into standby. 2 1 3 4 Selecting languages using the language code list Some of the language options (such as ‘DVD Language’ in the Setup Navigator) allow you to set your preferred language from any of the 136 languages listed in the language code list on page 38. 1 Select ‘Other Language’. 2 Use the cursor left/right ( ) buttons to select either a code letter or a code number. 3 Use the cursor up/down ( ) buttons to select a code letter or a code number. See Language code list on page 38 for a complete list of languages and codes. 01_DVD-S559_En.book Page 38 Friday, November 18, 2005 4:32 PM Additional information 08 Language code list Language (Language code letter), Language code Bhutani (dz), 0426 Esperanto (eo), 0515 Estonian (et), 0520 Basque (eu), 0521 Persian (fa), 0601 Finnish (fi), 0609 Fiji (fj), 0610 Faroese (fo), 0615 Frisian (fy), 0625 Irish (ga), 0701 Scots-Gaelic (gd), 0704 Galician (gl), 0712 Guarani (gn), 0714 Gujarati (gu), 0721 Hausa (ha), 0801 Hindi (hi), 0809 Croatian (hr), 0818 Hungarian (hu), 0821 Armenian (hy), 0825 Interlingua (ia), 0901 Interlingue (ie), 0905 Inupiak (ik), 0911 Indonesian (in), 0914 Icelandic (is), 0919 Hebrew (iw), 0923 Yiddish (ji), 1009 Javanese (jw), 1023 Georgian (ka), 1101 Kazakh (kk), 1111 Greenlandic (kl), 1112 Cambodian (km), 1113 Kannada (kn), 1114 Kashmiri (ks), 1119 Kurdish (ku), 1121 Kirghiz (ky), 1125 Latin (la), 1201 Lingala (ln), 1214 Laothian (lo), 1215 Lithuanian (lt), 1220 Latvian (lv), 1222 Malagasy (mg), 1307 Maori (mi), 1309 Macedonian (mk), 1311 Malayalam (ml), 1312 Mongolian (mn), 1314 Moldavian (mo), 1315 Marathi (mr), 1318 Malay (ms), 1319 Maltese (mt), 1320 Burmese (my), 1325 Nauru (na), 1401 Nepali (ne), 1405 Norwegian (no), 1415 Occitan (oc), 1503 Oromo (om), 1513 Oriya (or), 1518 Panjabi (pa), 1601 Polish (pl), 1612 Pashto, Pushto (ps), 1619 Quechua (qu), 1721 Rhaeto-Romance (rm), 1813 Kirundi (rn), 1814 Romanian (ro), 1815 Kinyarwanda (rw), 1823 Sanskrit (sa), 1901 Sindhi (sd), 1904 Sangho (sg), 1907 Serbo-Croatian (sh), 1908 Sinhalese (si), 1909 Slovak (sk), 1911 Slovenian (sl), 1912 Samoan (sm), 1913 Shona (sn), 1914 Somali (so), 1915 Albanian (sq), 1917 Serbian (sr), 1918 Siswati (ss), 1919 Sesotho (st), 1920 Sundanese (su), 1921 Swahili (sw), 1923 Tamil (ta), 2001 Telugu (te), 2005 Tajik (tg), 2007 Thai (th), 2008 Tigrinya (ti), 2009 Turkmen (tk), 2011 Tagalog (tl), 2012 Setswana (tn), 2014 Tonga (to), 2015 Turkish (tr), 2018 Tsonga (ts), 2019 Tatar (tt), 2020 Twi (tw), 2023 Ukrainian (uk), 2111 Urdu (ur), 2118 Uzbek (uz), 2126 Vietnamese (vi), 2209 Volapük (vo), 2215 Wolof (wo), 2315 Xhosa (xh), 2408 Yoruba (yo), 2515 Zulu (zu), 2621 English Japanese (ja), 1001 English (en), 0514 French (fr), 0618 German (de), 0405 Italian (it), 0920 Spanish (es), 0519 Chinese (zh), 2608 Dutch (nl), 1412 Portuguese (pt), 1620 Swedish (sv), 1922 Russian (ru), 1821 Korean (ko), 1115 Greek (el), 0512 Afar (aa), 0101 Abkhazian (ab), 0102 Afrikaans (af), 0106 Amharic (am), 0113 Arabic (ar), 0118 Assamese (as), 0119 Aymara (ay), 0125 Azerbaijani (az), 0126 Bashkir (ba), 0201 Byelorussian (be), 0205 Bulgarian (bg), 0207 Bihari (bh), 0208 Bislama (bi), 0209 Bengali (bn), 0214 Tibetan (bo), 0215 Breton (br), 0218 Catalan (ca), 0301 Corsican (co), 0315 Czech (cs), 0319 Welsh (cy), 0325 Danish (da), 0401 Country/Area code list Country/Area, Country/Area code, Country/Area code letter Argentina, 0118, ar Australia, 0121, au Austria, 0120, at Belgium, 0205, be Brazil, 0218, br Canada, 0301, ca Chile, 0312, cl China, 0314, cn Denmark, 0411, dk Finland, 0609, fi France, 0618, fr Germany, 0405, de Hong Kong, 0811, hk India, 0914, in Indonesia, 0904, id Italy, 0920, it Japan, 1016, jp Korea, Republic of, 1118, kr Malaysia, 1325, my Mexico, 1324, mx Netherlands, 1412, nl New Zealand, 1426, nz Norway, 1415, no Pakistan, 1611, pk Philippines, 1608, ph Portugal, 1620, pt Russian Federation, 1821, ru Singapore, 1907, sg Spain, 0519, es Sweden, 1905, se Switzerland, 0308, ch Taiwan, 2023, tw Thailand, 2008, th United Kingdom, 0702, gb USA, 2119, us 38 En 01_DVD-S559_En.book Page 39 Friday, November 18, 2005 4:32 PM 08 Additional information Glossary MP3 MP3 (MPEG1 audio layer 3) is a compressed stereo audio file format. Files are recognized by their file extension “.mp3”. MPEG audio An audio format used on Video CD/ Super VCDs and some DVD discs. PBC (PlayBack Control) A system of navigating a Video CD/ Super VCD through on-screen menus recorded onto the disc. PCM (Pulse Code Modulation) Digital audio encoding system found on CDs. Good quality, but requires a lot of data compared to Dolby Digital, DTS and MPEG encoded audio. See also Digital audio. Progressive scan video All the lines that make up a video picture are updated in one pass (compared to interlace which takes two passes to update the whole picture). Regions These associate DVD-Video discs and players with particular areas of the world. See DVD-Video regions on page 37 for more information. Sampling frequency The rate at which sound is measured to be turned into digital audio data. The higher the rate, the better the sound quality. CD is 44.1 kHz; DVD can be up to 96 kHz. See also Digital audio. WMA WMA is short for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. Files are recognized by their file extension “.wma”. Microsoft, Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries. Analog audio Direct representation of sound by an electrical signal. See also Digital audio. Aspect ratio The width of a TV screen relative to its height. Conventional TVs are 4:3; widescreen models are 16:9. Digital audio Indirect representation of sound using numbers. See also Sampling frequency and Analog audio. Dolby Digital*1 A multi-channel audio encoding system developed by Dolby Laboratories that enables far more audio to be stored on a disc than PCM encoding. See also PCM (Pulse Code Modulation). DRM WMA) DTS*2 DRM (Digital Rights Management) copy protection is a technology designed to prevent unauthorized copying by restricting playback, etc. of material on devices other the PC (or other WMA recording equipment) used to record it. For detailed information, please see the instruction manuals or help files that came with your PC (or other WMA recording equipment) and/or software. A multi-channel audio encoding system developed by Digital Theater Systems that enables far more audio to be stored on a disc than PCM encoding. See also PCM (Pulse Code Modulation). EXIF A file format developed by Fuji Photo (Exchangeable Film for digital still cameras. Digital cameras from various manufacturers Image File) use this compressed file format which carries date, time and thumbnail information, as well as the picture data. File extension A tag added to the end of a filename to indicate the type of file. For example, “.mp3” indicates an MP3 file. 39 En ISO 9660 format International standard for the volume and file structure of CD-ROM discs. JPEG A standard file format used for still images. JPEG files are identified by the file extension “.jpg”. *1 Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. *2 “DTS” and “DTS Digital Out” are registered trademarks of Digital Theater Systems, Inc. 10_additional_info.fm Page 40 Tuesday, November 22, 2005 11:36 AM Additional information Specifications System . . . . . . . . . . . . . . . . . . . . . . . . DVD player Power requirements . . .AC 220–240 V, 50/60 Hz Power consumption . . . . . . . . . . . . . . . . . . . 7 W Power consumption (standby) . . . . . . . . . 0.7 W Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.8 kg Dimensions . . . . 435 (W) x 61 (H) x 213 (D) mm Operating temperature . . . . . . . . +5°C to +35°C Video output Output level . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA Audio output (1 stereo pair) Output level . . . . . . . . . . . . . During audio output 200 mVrms (1 kHz, –20 dB) Number of channels . . . . . . . . . . . . . . . . . . . . . 2 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA English General 08 Digital audio characteristics RGB (SCART) output Output level . . . . . . . . . . . . . . . . . 0.7 Vp-p (75 Ω) Connection. . . . . . . . . . . . . . . . . . Euroconnector Frequency response . . . . . . . . . . 4 Hz to 44 kHz (DVD fs: 96 kHz) Component video output S/N ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .115 dB Dynamic range . . . . . . . . . . . . . . . . . . . . . .101 dB Total harmonic distortion. . . . . . . . . . . . 0.0023 % Y (luminance) - Output level . . . . . . . . . . . . . . . . . . . . . . . .1 Vp-p (75 Ω)(Green) Pb/Cb (color) - Output level . . . . . . . . . . . . . . . . . . . . . . . 0.7 Vp-p (75 Ω)(Blue) Pr/Cr (color) - Output level . . . . . . . . . . . . . . . . . . . . . . . . 0.7 Vp-p (75 Ω)(Red) Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . RCA Coaxial digital output . . . . . . . . . . . . . . . . . . .RCA IEC60958 for CDDA/LPCM IEC61937 for MPEG 1/2, Dolby Digital and DTS S-video output Y (luminance) - Output level . . . . . . 1 Vp-p (75 Ω) C (color) - Output level . . . . . . 286 mVp-p (75 Ω) Connection. . . . . . . . . S-video (Mini, DIN, 4 pins) Digital output Accessories Audio/video cable . . . . . . . . . . . . . . . . . . . . . . . . Power cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . AA/R6 dry cell batteries . . . . . . . . . . . . . . . . . . Owner’s manual 1 1 1 2 The specifications and design of this product are subject to change without notice, due to improvement. 40 En DVD-S559_Ru.book Page 47 Friday, November 18, 2005 6:58 PM J2G53923A SH 06/01 U YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA 2005 ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 V€ STRA FR…LUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed All rights reserved. in Thailand J2G53923A (WG69420)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Yamaha DVD-S559 de handleiding

Categorie
Dvd spelers
Type
de handleiding