Digital Sound Projector
Owner’s Manual
Read the supplied booklet “Quick Reference Guide” before using the unit.
English
for Europe model
En 2
CONTENTS
FEATURES 4
What you can do with this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Preparing remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Controls and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PREPARATIONS 11
General setup procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
a Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
b Connecting a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
c Connecting playback devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
d Other connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connecting a subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Wired network connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
e Connecting the power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
f Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Displaying the menu screen on the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Selecting the language for menu display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Auto setup for appropriate surround effects (IntelliBeam) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Operating the unit by TV’s remote control (HDMI control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
PLAYBACK 37
Basic operation for playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Enjoying sound based on your preference . . . . . . . . . . . . . . . . . . . . . . . . 38
Playback with 3D surround sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Playback with surround sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Enjoying three-dimensional surround sound (CINEMA DSP 3D/CINEMA DSP) . . . . . . . . . . . . . . . . . . . . . . . .39
2-channel playback (stereo playback mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Delivering sound to a specified location (target playback mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Playing back digitally compressed formats (such as MP3, etc.) with enriched sound
(Compressed Music Enhancer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Clear playback of human voices (CLEAR VOICE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Adjusting the position from which dialog is heard (Dialog Lift) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Adjusting volume for each channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Using useful features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Saving energy with the Eco function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Switching information displayed in the front panel display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Saving this unit’s settings to system memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Wireless playback of audio via Bluetooth connection . . . . . . . . . . . . . . 46
Listening to music from a Bluetooth device (Receiving) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Listening to audio through Bluetooth speakers or headphones (transmitting) . . . . . . . . . . . . . . . . . . . . . . . 49
En 3
NETWORKS 50
Network functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Connecting to a network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Wired network connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Wireless network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Connecting a mobile device to the unit directly (Wireless Direct) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Playing back music stored on media servers (PCs/NAS) . . . . . . . . . . . . 61
Media sharing setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Playing music files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Listening to Internet radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Playback of Internet radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Registering favorite Internet radio stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Playing back music with AirPlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Playback of iTunes/iPod music contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Playing back music stored on mobile devices . . . . . . . . . . . . . . . . . . . . . 66
Using a mobile device to play songs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
SETTINGS 67
Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Setting the setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Setup menu list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Settings each input source (Option menu) . . . . . . . . . . . . . . . . . . . . . . . . 84
Setting the option menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Option menu list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Advanced setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Setting the advanced setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Advanced setup list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Updating the unit’s firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Using “Network Update” in the setup menu to update firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Updating firmware with connection of a USB flash drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
APPENDIX 91
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Messages in the front panel display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Status indicator on the wireless subwoofer kit SWK-W16 . . . . . . . . . . 99
When surround effect is not enough . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Installing and adjusting the sound reflection board YRB-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Basic Knowledge of Surround Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
What is a Digital Sound Projector? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
What is Object Based Audio? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Yamaha’s Audio Technologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Network information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
FEATURES ➤ What you can do with this unit En 4
FEATURES
What you can do with this unit
Audio
Audio
Control
Audio
Network contents
Mobile
devices
Control
Audio
Audio
Bluetooth
headphones
Mobile
devices
MusicCast devices
HDMI
Control
BD/DVD player
This unit’s
remote control
Audio/
Video*
Audio Audio/
Video*
HDMI
Control
TV remote
control
TV
The unit
Audio
Control
Audio
Subwoofer (optional or available
from third-party manufactures)
Wireless subwoofer kit
SWK-W16
* Supports 4K video and HDCP version 2.2
Sound beams are reflected off walls and a ceiling using unique
real surround sound formats and techniques, allowing listeners to
enjoy their preferred acoustic environment.
• Automatically and quickly adjusts surround
sound effects for the listening room setup
(IntelliBeam)
. p. 30
• Emphasize the sense of immersion and reality of
the sound field with overhead sounds fed via
height channels (3D Surround Sound)
. p. 38
• Reproducing stereo or multichannel sounds with
the sound fields like actual movie theaters and
concert halls (CINEMA DSP 3D/CINEMA DSP)
. p. 39
• Enjoying compressed music with enhanced
sound (Compressed Music Enhancer)
. p. 42
• Delivering sound to a specified location (Target
playback mode)
. p. 41
Sequential operation of a TV, this unit, and
BD/DVD player (HDMI Control)
. p. 35
Listen to audio input to the
unit with Bluetooth
headphones or speakers
. p. 49
Plays back audio content
from Bluetooth
®
devices
. p. 47
Share music
via your home
network
. p. 5
Dedicated apps
for mobile
devices
. p. 5
Wide variety of supported content
• Media server (PC/NAS)
. p. 61
• Internet radio
. p. 62
•AirPlay
. p. 64
• Music stored on mobile
devices
. p. 66
FEATURES ➤ What you can do with this unit En 5
Achieve true 3D surround sound including height
channel audio with the unit alone
Until now, digital sound projectors have reproduced a two-dimensional sound field with
five distinct sound beams: left front, right front, center, left surround, and right surround.
This unit reproduces a three-dimensional sound field offering a greater sense of
immersion and depth by directing additional two sound beams (left height and right
height) upward. It also enables playback in the DTS:X or Dolby Atmos format, which
uses height channel audio signals as input sources. It further incorporates CINEMA
DSP 3D, which produces a more effective sound field.
Dialog Lift function
When playing movies, this feature can be adjusted so that audio such as narratives and
dialog is output from the center speakers, as in a movie theater where speakers are
installed behind the screen, allowing for a sense of integration of conversation with the
movements of the actors (p. 42).
Unrestricted playback of music over a network using
MusicCast CONTROLLER
The free dedicated app for mobile devices, MusicCast CONTROLLER, allows you to
listen to music stored on mobile devices such smartphones, or on servers, or to listen to
Internet radio stations and many kinds of major streaming services.
This app also allows you to distribute content to other MusicCast-enabled devices for
synchronized playback.
See the “MusicCast Setup Guide” for details.
Search for “MusicCast CONTROLLER” on the App Store or Google Play.
Bluetooth
functions
You can receive and play audio from a Bluetooth device, such as a mobile device over
a wireless connection. You can also transmit audio input to the unit to a Bluetooth
headphones.
Using HOME THEATER CONTROLLER (WLAN) to easily
operate the unit
The free dedicated app for mobile devices, HOME THEATER CONTROLLER (WLAN),
allows you to easily operate the unit, performing such tasks as configuring sound
beams on a visual screen, selecting an input source, and adjusting the volume on a
mobile device.
Search for “HOME THEATER CONTROLLER (WLAN)” on the App Store or Google Play.
Wireless subwoofer connection using the wireless
subwoofer kit
The unit and the subwoofer can be connected via a wired connection. In addition, a
wireless connection can be established using the wireless subwoofer kit (SWK-W16) (p.
25).
• In this manual, iOS and Android mobile devices are collectively referred to as “mobile devices”. The specific
type of mobile device is noted in explanations as needed.
The sound image of the system
FEATURES ➤ Supplied accessories En 6
Before connecting, make sure you have received all of the following items.
Supplied accessories
1
China model only: Instead of the optical cable, a digital coaxial audio cable is supplied.
2
The shape of the power cable plug varies depending on where the unit was purchased.
• The supplied optical cable may not be needed depending upon connections.
About this manual
• In this manual, operations that can be performed using either the front panel keys or the remote control
are explained using the remote control.
• indicates supplementary explanations for better use.
• indicates precautions for use of the unit and its feature limitations.
Supplied accessories
The unit Wireless subwoofer kit (SWK-W16)
Remote control Batteries
(AAA, R03, UM-4) (x2)
Optical cable (1.5 m)
1
Power cable (2 m)
2
IntelliBeam microphone (6 m) Cardboard microphone stand
Stands (x2) Screws (For the stands; x2) Subwoofer cable (3 m) System control cable (3 m)
• Owner’s Manual CD-ROM • Quick Reference Guide • MusicCast Setup Guide
FEATURES ➤ Supplied accessories En 7
Preparing remote control
Before installing batteries or using the remote control, be sure to read battery and remote control precautions in “Quick Reference Guide” (separate booklet).
Installing the batteries
Battery × 2
(AAA, R03, UM-4)
Press down on the arrow
and slide the cover in the
direction in which it
points.
Slide the cover back to close it.
Operation range
Within 6 m
FEATURES ➤ Controls and functions En 8
1 STATUS indicator
Lights to show the system condition.
Glows green: Power on
Glows red: Power off (when the HDMI control or network
standby is activated)
Turns off: Power off
2 (Wi-Fi) indicator
Shows the status of wireless network connection (p. 52).
3 (Bluetooth) indicator
Shows the status of Bluetooth connection (p. 46, 49).
4 Remote control sensor
Receives infrared signals from the remote control (p. 10).
5 Front panel display
Displays the unit’s settings, such as the name of an audio
input source or surround mode (p. 44). The setting values
are also displayed.
6 INTELLIBEAM MIC jack
For connecting the supplied IntelliBeam microphone (p. 31).
7 INPUT/CONNECT key
INPUT key
Select an audio input source.
CONNECT key
Use to control the unit using the dedicated MusicCast
CONTROLLER app for mobile devices. See the MusicCast
Setup Guide for details.
8 VOLUME (+/-) keys
Adjust the volume of the unit (p. 37).
9 z key
Turn on/off the unit.
• When the unit is turned off, this unit consumes a small amount of
power in order to search for HDMI signals or to receive signals from
a network device.
• The front panel display turns on for 3 seconds only when the unit is
operated.
• “Dimmer” can adjust the brightness of the front panel display and
indicators in the setup menu (p. 78).
Controls and functions
The unit (front, top)
STATUS
INTELLIBEAM MIC
CONNECT
INPUT
VOLUME
123 4 5 6
798
FEATURES ➤ Controls and functions En 9
• So that the HDMI and NETWORK jacks may be easily located, the illustration of the rear of the unit used in this manual shows their respective positions with the labels used on the unit itself.
1 SYSTEM CONNECTOR jack
Connect to a Yamaha subwoofer so that the subwoofer
functions according to the unit’ power on and off (p. 25).
2 SUBWOOFER OUT jack
For connecting to the subwoofer using a wired connection
(p. 25).
3 AUX1 analog input jacks
For connecting to a playback device equipped with the
analog audio output jacks (p. 24).
4 AUX2 digital coaxial input jack
For connecting to a playback device equipped with a digital
coaxial audio output jack (p. 24).
5 TV and OPTICAL jacks
For connecting to a playback device equipped with an
digital optical audio output jack (p. 22, 23).
6 IR-IN, IR-OUT, and RS-232C jacks
They are control expansion jacks for commercial use only.
7 UPDATE ONLY jack
Use to update this unit’s firmware (p. 88).
8 HDMI IN 1–4 jacks
For connecting an HDMI-compatible playback device such
as a BD/DVD player, a satellite and cable TV tuner, and a
game console (p. 23).
9 HDMI OUT (ARC) jack
For connecting to an HDMI-compatible TV and outputting
video/audio signals (p. 22).
0 NETWORK jack
For connecting to a network with a network cable (p. 52).
A AC IN jack
Connect the supplied power cable (p. 27).
The unit (rear)
SYSTEM
CONNECTOR
AC IN
RL
AUX1
AUX2 TV OPTICAL
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-IN IR-OUT
UPDATE ONLY
RS-232C
NETWORK
SUBWOOFER
OUT
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
NETWORK
SYSTEM
CONNECTOR
RL
AUX1
AUX2 TV OPTICAL IR-IN IR-OUT
UPDATE ONLY
RS-232C
SUBWOOFER
OUT
a
12 4 7
0
563
8
9
FEATURES ➤ Controls and functions En 10
1 ECO key
Turn the Eco function on or off (p. 44).
2 Input selector keys, NET key
Input selector keys
Select an audio input source to be played back (p. 37).
NET key
Select an audio input via a network (p. 50). Each time the key
is pressed, the input source is selected as follows:
SERVER NET RADIO AirPlay Streaming music
service (if available) MusicCast Link SERVER …
3 SYSTEM MEMORY keys
Save IntelliBeam measurements, speaker volume, and other
settings (p. 45).
4 SUB (+/-) key
Adjust the volume of the subwoofer (p. 37).
5 MUTE ( ) key
Mute the sound (p. 37).
6 SETUP ( ) key
Display the setup menu (p. 67).
7 S/T/W/X keys, ENTER key
Change the setting (p. 67).
8 RETURN ( ) key
Return to the previous menu screen.
9 CINEMA DSP program keys
When playback is in surround playback mode, select the
CINEMA DSP programs (p. 39).
0 SURROUND key
Switch to surround playback mode (p. 39).
A 3D SURROUND key
Switch to 3D surround playback mode (p. 38).
B CLEAR VOICE key
Turn the CLEAR VOICE function on or off (p. 42).
C ENHANCER key
Turn Compressed Music Enhancer to on or off (p. 42).
D z key
Turn on/off the unit (p. 37).
E NET RADIO (1–3) keys
Register and play streaming services such as Internet radio
stations via the unit (p. 62).
F DIALOG LIFT key
Use the Dialog Lift function to adjust the height from which
dialog is heard (p. 42).
G VOL (+/-) key
Adjust the volume of the unit (p. 37).
H OPTION ( ) key
Display the option menu for each input source (p. 84).
I INFO ( ) key
Switch the information display on the front panel (p. 44).
J STEREO key
Switch to stereo playback mode (p. 41).
K TAR GET k ey
Switch to target playback mode (p. 41).
L WPS/CH LEVEL key
WPS key
Use the key when connecting to a wireless router (access
point) that supports the WPS (push button) feature (p. 54).
CH LEVEL key
Adjust the volume balance during playback (p. 43).
M CONNECT key
Use to control the unit using the dedicated MusicCast
CONTROLLER app for mobile devices. See the MusicCast
Setup Guide for details.
Remote control
1
d
e
f
g
h
i
j
k
l
m
2
3
4
5
6
7
8
9
a
0
c
b
Infrared signal transmitter
PREPARATIONS ➤ General setup procedure En 11
PREPARATIONS
This completes all the preparations. Enjoy playing movies, music and other content with the unit!
• See “NETWORKS” (p. 50) for information regarding network connection and audio playback via a network.
General setup procedure
1 Installation (p. 12)
Position the unit to achieve the optimal surround sound effects. The unit can also be mounted
on a wall.
2 Connecting a TV (p. 22)
Connect a TV to the unit.
3 Connecting playback devices (p. 23)
Connect video devices (such as BD/DVD players) to the unit.
4 Other connections (p. 25)
Connect a subwoofer.
Use a network cable to connect the unit to a router in preparation for wired network connection.
5 Connecting the power cable (p. 27)
After all the connections are complete, plug in the power cable.
6 Initial settings (p. 28)
Perform initial setup, such as adjusting surround sound effects, before attempting playback.
PREPARATIONS ➤ a Installation En 12
This unit reflects sound beams off of walls and a ceiling to create the surround sound effect. The position of this unit in relation to the listening position, walls, and a ceiling is important
to achieving the desired surround sound effects. Refer to pages 12 to 16 when installing the unit. When installing this unit on a rack behind which there is limited space, for example,
it may be easier to connect external devices to this unit first. This will depend upon the installation location. See pages 22 to 27 for information regarding the connection of external
devices.
a Installation
Notes
• Be sure to install this unit on a large, stable stand where it does not fall subject to vibrations, such as from an earthquake, and where it is out of the reach of children.
• There is a built-in antenna on the top of the unit. Do not install it on a metal rack, and do not stack metal items on top of the unit.
• The unit’s speakers are not magnetically shielded. Do not install hard disk drives or similar devices near the unit.
• Do not stack the unit directly on top of other playback devices, or vice versa. Heat and vibrations may result in damage or malfunction.
Recommended place for installation
1
Height channel audio is output in a diagonal
direction upward and forward from the unit (p. 5).
2
Depending upon the rack, table-top stand, or
floor stand used, the stands may not be
necessary.
• Install the unit in the center of the left and right
walls.
• This unit can be mounted on a wall (p. 17).
• The listening position (such as sofa, etc.) should be
located at the front of the unit.
• The distance between the listening position and the
unit should be more than 1.8 m.
• Set the listening position as far from the back wall as
possible (the optimal listening position is halfway
between the unit and the back wall, or slightly closer
to the back wall).
• To achieve desired surround sound effects, be
sure that obstacles such as furniture may not
obstruct the path of sound beams (p. 13).
• Be sure that the unit installed with at least 5 cm
of empty space above and below it.
• Leaving as much space as possible in a
diagonal direction in front of, and above, the
unit when installing it.
1
• Attach the supplied stands to the unit if it will
be installed on a rack
2
(p. 16).
1 2 3 4 5 6
PREPARATIONS ➤ a Installation En 13
This unit outputs sound beam as shown in the illustrations below. Install this unit where
there are no obstacles such as furniture obstructing the path of sound beams.
Otherwise, the desired surround sound effects may not be achieved.
If the unit is installed so that it is parallel to a wall, install it as close to the exact center of
the wall as possible.
If the unit is installed in a corner of a room, position it at a 40–50° angle to the adjacent
walls.
Parallel installation
Install this unit as close to the exact center of the wall as possible.
• If the unit cannot be installed evenly between the left and right walls, sound beams can be adjusted to
achieve natural surround sound effects (p. 16).
Ideal installation condition
Install this unit as close to the exact front of your normal listening position as possible.
The distance between listening position and the unit should be more than 1.8 m.
Example for installing the unit
Objects,
such as
furniture
Parallel installation: Viewed from above
40° to 50°
Objects, such as
furniture
Corner installation: Viewed from above
Viewed from the side
Sound beams
are reflected off
the ceiling
Sound beam output varies depending upon the 3D surround/Surround setting (p. 38, 39)
and the channel output setting (p. 73). The illustration above shows the path of sound
beams when 3D surround is enabled and “Front” in the Channel Out setting is set to
“Beam”.
Viewed from the side
The illustrations above show the path of sound beams when 3D surround is enabled
(p. 38) and “Front” in the Channel Out setting is set to “Stereo”. (p. 73).
Sound beams
are reflected off
the ceiling
More
than
1.8 m
More than 1.8 m
1 2 3 4 5 6
PREPARATIONS ➤ a Installation En 14
Installing in a non-square room
Install this unit so that the sound beams can be reflected off the walls.
• If this unit cannot be repositioned, or the listening position cannot be changed, the optional YRB-100 sound
reflection board may be installed for a better surround sound experience (p. 100).
Irregularly shaped rooms with solid walls on all sides
Irregularly shaped rooms that are open to a hallway on one side
1 2 3 4 5 6
PREPARATIONS ➤ a Installation En 15
Example for installing the unit in living room
• The legs on a table are not considered obstacles as sound beams normally pass
through them. A cupboard installed facing the wall reflects sounds.
• As the heavy curtains absorb sounds, the sound features of the listening room is
different from the case with the curtain opened and the case with the curtain closed.
Using saving settings function enables to save the best settings for each case of
listening room (p. 45).
This unit creates surround sound by reflecting projected sound beams off the walls and
the ceiling of your listening room. The surround sound effects produced by this unit
may not be sufficient when this unit is installed in the following locations.
• Rooms with walls inadequate for reflecting sound beams
• Rooms with acoustically absorbent walls and ceiling
• Rooms with measurements outside the following range:
W (3 to 7 m) × H (2 to 3.5 m) × D (3 to 7 m)
• Rooms where objects such as furniture are likely to obstruct the path of sound beams
• Rooms with less than 1.8 m from the listening position to this unit
• Rooms where the listening position is close to the walls
• Rooms where the listening position is not in front of this unit
• Rooms with a complex shape, such as a slanted ceiling (ceiling lights do not obstruct
sound beams)
The My Surround function creates rich surround sound effects in rooms with less than
optimal surround sound conditions. See “Channel Out” (p. 73) for more information.
Objects, such as
furniture
Unrecommended listening environments
Enjoying surround effects regardless of conditions (My
Surround)
1 2 3 4 5 6
PREPARATIONS ➤ a Installation En 16
This unit’s AUTO SETUP (p. 30) can be used to automatically adjust sound beams to
achieve the optimal surround playback environment according to the listening room
setup. In addition to using AUTO SETUP, sound beams can be adjusted manually to
achieve surround sound effects best suited to the listening room setup when the unit is
installed as described below.
Installing the unit near a corner of the room
When installing the unit near a corner of the room as shown in the illustration below,
front channel sound may seem to come from an unnatural direction if beam settings are
configured using AUTO SETUP.
Should this occur, adjust the left and right front channels using “Image Location” (p. 72)
in the setup menu to achieve more natural sound.
Installing the unit in an irregularly shaped room
When the unit is installed in a room that is not rectangular, sound beams may not be
properly reflected off the walls as shown in the illustration below.
Should this occur, perform AUTO SETUP, and then adjust the angle of beam from the
channel from which sound is not properly heard using “Horizontal Angle” (p. 70) in the
setup menu to achieve even distribution of sound.
Install the stands (supplied) on the bottom of the unit. Align and insert the protrusion on
the stands into the holes on the rear panel of the unit as shown in the illustration, and
then tighten the screws (supplied) to lock the stands in place. The stands need not be
installed when the unit is mounted on a wall using the optional Wall Mount Bracket
SPM-K30.
Adjusting sound beams to achieve optimal surround
sound effects
Left front channel adjusted
When left front channel sound is
unnatural
Installing the stands
Stand (supplied)
Screws (supplied) Stand (supplied)
1 2 3 4 5 6
PREPARATIONS ➤ a Installation En 17
The unit can be installed on a shelf, either above or below the TV, on a third-party rack.
The rack and the shelf on which the unit is placed should be large enough to allow
adequate ventilation around the unit and the rack should be sturdy enough to support
the weight of both the unit and the TV.
The unit can be mounted on a wall using the optional Wall Mount Bracket (such as
SPM-K30).
Dimensions when the unit is mounted using the SPM-K30
Be sure to refer to the dimensions below and leave adequate space for ventilation
around the unit.
Installing the unit on a rack
TV
Mounting the unit on a wall
Notes
Instructions for mounting the unit are not included in the Installation Manual supplied
with the SPM-K30. Always follow the instructions provided in this Owner’s Manual.
Wall Mount Bracket (SPM-K30)
TV
4- 7
24- 7x22
92
114
730
188 355 182355
26.5
71.5
19.4
112.4
SPM-K30 (optional)
YSP-5600
(mm)
1 2 3 4 5 6
PREPARATIONS ➤ a Installation En 18
• The SPM-K30 may not be available in some countries or regions.
• When the unit will be installed using the wall mount bracket, all installation work should be performed by a
qualified contractor or experienced retail staff. The customer should not attempt to install the unit
themselves. Improper installation may cause the unit to fall, resulting in personal injury.
• Installation must be secure enough to bear the weight of the unit and the wall mount bracket, possibly for
years to come, and must also be secure enough to withstand vibrations, such as those caused by
earthquakes. Improper installation may cause the unit to fall, resulting in personal injury.
• To prevent the unit from falling, attach it to a wall constructed of drywall (plasterboard).
• Be sure to use screws capable of supporting the weight of the wall mount bracket and the unit (with steps 2
and 7). Using items other than the specified screws, such as shorter screws, nails, or double-sided tape,
may cause the unit to fall, resulting in personal injury.
• To ensure safety, all screws must be tightened securely. Loose screws may cause the unit to fall, resulting
in personal injury.
• Be sure to leave adequate space for ventilation around the unit so that heat generated by the unit is allowed
to dissipate. Failure to provide adequate space around the unit may cause the unit to overheat internally,
resulting in a fire.
• Do not lean on the unit or apply excessive force to the top of the unit. Doing so may cause the unit to fall,
resulting in personal injury.
• Fix cables in place so that they will not become loose. If a foot or hand becomes accidentally entangled in,
or catches on, a loose cable, the unit may fall, resulting in personal injury.
• Once the unit is installed, safety checks should be conducted on a regular basis. When the unit is used
over an extended period of time, screws can become loose and the installation can weaken due to the
passage of time, vibrations, etc.
• Note that Yamaha cannot be held liable for accidents, including falling of the unit, resulting from improper
installation of the unit, or for damage to walls.
1
Assemble the large wall mount bracket.
Align the screw holes A on the left bracket with those on the right bracket, and
tighten the screws.
2
Attach the wall mount bracket assembled in step 1 to the wall.
In order to secure the unit to the wall, the bracket must first be attached to the
wall in a manner suited to the structure and quality of the wall.
• In order to secure the unit to the wall, drive six (or more) tapping screws from the outside through the holes
in the wall mount bracket.
A
A
730 mm
Large wall mount bracket (left)
Large wall mount
bracket (right)
Screw (M4; supplied with the SPM-K30)
4mm self-tapping screws (available from third-party manufacturers)
Washers (available from third-party manufacturers)
Installing into a
dray wall
Installing directly
into a wall, etc.
25 mm or more
Dry wall
25 mm or more
Beam, etc.
1 2 3 4 5 6
PREPARATIONS ➤ a Installation En 19
3
Attach the small wall mount brackets to the unit.
4
Attach the safety wires to the small wall mount brackets (left and
right) to prevent the unit from falling.
Screws (M4;
supplied with the
SPM-K30)
Small wall mount
bracket (Type B)
Small wall mount
bracket (Type B)
Screw hole
(left side)
Screw hole
(right side)
Screws(M4;
supplied with
the SPM-K30)
Safety wire
Slip one end through
the loop at the other end
Slip the safety wire
between the bracket and
the projector
1 2 3 4 5 6
PREPARATIONS ➤ a Installation En 20
5
Fit the mounting guide hooks of the small wall mount brackets
attached to the unit into the holes on the left and right sides of the
large wall mount bracket and then slide the unit to the right.
• Hold the unit tight with both hands when attaching or removing the unit to or from the wall. Holding the unit
loosely could cause the unit to fall, resulting in personal injury.
6
Align the holes in the large wall mount bracket with the holes in the
bottom of the small wall mount brackets, and then use two of the
screws (M6; supplied with the SPM-K30) to secure the unit.
Fit the hook into
the hole.
Slide the unit to the
right.
Screws
(M6; supplied with the
SPM-K30)
Bottom side of the unit
1 2 3 4 5 6
PREPARATIONS ➤ a Installation En 21
7
Pass the screws through the loops of the safety wires and then
tighten the screws to secure the safety wires to the wall.
• Attach the safety wires tight.
• Keep the two other washers for future use.
Secure the safety
wire to the wall.
Screw (available
from third-party
manufactures)
Washer (supplied
with the SPM-K30)
Secure the
safety wire to
the wall.
1 2 3 4 5 6
PREPARATIONS ➤ b Connecting a TV En 22
Connect a TV to the unit so that video input to the unit can be output to the TV. You can also enjoy playback of TV audio on the unit.
• Use a 19-pin HDMI cable with the HDMI logo printed on it. A cable with a maximum length of 5 m is recommended to prevent degradation of signal quality.
• For playback of 3D and 4K video content, use a high-speed HDMI cable.
• This unit supports HDCP version 2.2, a copy protection technology. To enjoy playback of 4K video, connect the unit to the HDMI IN jack (one compatible with HDCP 2.2) on an HDCP 2.2-compliant TV.
Connect the TV to the unit with an HDMI cable (not supplied).
When connecting a TV that supports Audio Return Channel (ARC), enable the HDMI
control function (p. 77).
• Use an ARC-compatible HDMI cable.
Connect the TV to the unit with an HDMI cable (not supplied) and an optical cable.
• If the TV has no optical jack
Connect the audio output jack on the TV to the AUX1 (analog) input jack or AUX2 (digital coaxial) jack on
the unit, and set “TV Input” in the setup menu to “Analog [AUX 1]” or “Coaxial [AUX 2]” accordingly (p. 77).
TV audio can be played through the unit by pressing the TV key on the remote control.
b Connecting a TV
TVs that support Audio Return Channel (ARC)
What is Audio Return Channel (ARC)?
In order for the unit to play audio from a TV, the TV must usually be connected to the unit via an audio
cable as well as an HDMI cable. If, however, the TV supports Audio Return Channel (ARC), TV audio
signals can be input to the unit via the HDMI cable that outputs video signals from the unit to the TV.
SYSTEM
CONNCETOR
RL
AUX1
AUX2 TV OPTICAL IR-IN
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-OUT
UPDATE ONLY
RS-232C
NETWORK
SUBWOOFER
OUT
HDMI
(ARC)
OUT
(ARC)
HDMI HDMI
The unit (rear)
HDMI OUT (ARC) jack
ARC-compatible HDMI input
TV
TVs that do not support Audio Return Channel (ARC)
SYSTEM
CONNCETOR
RL
AUX1
AUX2 TV OPTICAL IR-IN
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-OUT
UPDATE ONLY
RS-232C
NETWORK
SUBWOOFER
OUT
HDMI
OPTICAL
TV
OUT
(ARC)
HDMI HDMI
OO
The unit (rear)
HDMI OUT (ARC) jack HDMI input
TV jack Audio output
(digital optical)
TV
1. Remove the cap 2. Check the direction of
the plug
1 2 3 4 5 6
PREPARATIONS ➤ c Connecting playback devices En 23
Connect video devices such as BD/DVD players, set-top boxes (STBs) and game consoles to the unit. Depending on the video/audio output jacks available on your video device,
choose one of the following connections. We recommend using an HDMI connection if the video device has an HDMI output jack.
Connect a video device to the unit with an HDMI cable (not supplied).
• This unit supports HDCP version 2.2, a copy protection technology. When using an HDCP 2.2-compliant
playback device, such as a set-top box, connect it to the unit via the HDMI IN 1 jack. When connecting
playback devices that do not support HDCP version 2.2, any HDMI IN jack (1–4) may be used.
The audio/video played on the video device will be output though the unit by switching
input to HDMI 1–4 using the HDMI 1–4 key on the remote control.
• Once the HDMI control function has been activated (p. 35), video and audio content from playback devices
can be output from the TV even when this unit is off (HDMI signal pass-through).
• Use a 19-pin HDMI cable with the HDMI logo printed on it. A cable with a maximum length of 5 m is
recommended to prevent degradation of signal quality.
• For playback of 3D and 4K video content, use a high-speed HDMI cable.
• When audio from the video device cannot be output via the HDMI jack, use an optical cable to connect the
video device to the unit via the digital optical output jack on the video device and the OPTICAL jack on the
unit. If the video device is connected to the unit in this way, change “Audio Assign” to “Optical” in option
menu (p. 85).
Connect a video device to this unit via the optical cable. Next, connect the video
device’s video output to the TV’s video input.
The audio played on the video device will be output though the unit by switching input
to OPTICAL using the OPTICAL key on the remote control.
c Connecting playback devices
HDMI connection
SYSTEM
CONNCETOR
RL
AUX1
AUX2 TV OPTICAL IR-IN
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-OUT
UPDATE ONLY
RS-232C
NETWORK
SUBWOOFER
OUT
HDMI
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
HDMI HDMI
The unit (rear)
HDMI IN 1–4 jacks
HDMI output
Video device
Optical connection
SYSTEM
CONNCETOR
TV
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-IN IR-OUT
UPDATE ONLY
RS-232C
NETWORK
SUBWOOFER
OUT
RL
AUX1
AUX2 OPTICAL
OPTICAL
OPTICAL
OO
The unit (rear)
OPTICAL jack
Audio output
(digital optical)
1. Remove the cap 2. Check the direction of
the plug
Video device
TV
To video output
jack
To video input
jack
1 2 3 4 5 6
PREPARATIONS ➤ c Connecting playback devices En 24
Connect a video device to this unit via a digital coaxial cable. Next, connect the video
device’s video output to the TV’s video input.
The audio played on the video device will be output though the unit by switching input
to AUX2 using the AUX 2 key on the remote control.
Connect a video device to this unit via a stereo cable (not supplied). Next, connect the
video device’s video output to the TV’s video input.
The audio played on the video device will be output though the unit by switching input
to AUX1 using the AUX 1 key on the remote control.
Coaxial connection
SYSTEM
CONNCETOR
TV OPTICAL
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-IN IR-OUT
UPDATE ONLY
RS-232C
NETWORK
SUBWOOFER
OUT
RL
AUX1
AUX2
COAXIAL
AUX2
CC
The unit (rear)
AUX2 (digital
coaxial) jack
Audio output
(digital coaxial)
Video device
TV
To video output jack
To video input jack
Analog connection
SYSTEM
CONNCETOR
AUX2 TV OPTICAL
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-IN IR-OUT
UPDATE ONLY
RS-232C
NETWORK
SUBWOOFER
OUT
RL
AUX1
AUDIO
R
L
R
AUX1
L
L
R
L
R
The unit (rear)
AUX1 (analog) jacks
Audio output
(analog)
Video device
TV
To video output jack
To video input jack
1 2 3 4 5 6
PREPARATIONS ➤ d Other connections En 25
Connecting a subwoofer
A subwoofer can be connected to the unit for use with the unit. There are two ways to
connect a subwoofer to the unit: use a third-party RCA monaural cable, or use the
wireless subwoofer kit SWK-W16 to connect via a wireless connection.
Use a third-party RCA monaural cable to connect the subwoofer to the unit via the
monaural input jack on the subwoofer and the SUBWOOFER OUT jack on the unit.
When connecting a Yamaha subwoofer equipped with a system connector, connect a
system control cable (or third-party 3.5mm monaural mini plug cable) to the SYSTEM
CONNECTOR on the unit. This connection is required to turn the unit and subwoofer on
and off at the same time.
When the unit is connected to the subwoofer via the cable, set the subwoofer output to
“Wired” in the setup menu (p. 74)
• See documentation supplied with the subwoofer for more information.
The wireless subwoofer kit SWK-W16 enables wireless connection of a subwoofer to the
unit.
❑ Installing the SWK-W16
Install the SWK-W16 on or near the subwoofer. If subwoofer vibrations cause the
SWK-W16 to move when installed on the subwoofer, install it elsewhere or fix it in place
so that it does not move.
d Other connections
Connecting a subwoofer via cable
AUX2 TV OPTICAL
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-IN IR-OUT
UPDATE ONLY
RS-232C
NETWORK
RL
AUX1
SYSTEM
CONNCETOR
SUBWOOFER
OUT
SYSTEM
CONNECTOR
SUBWOOFER
OUT
INPUT SYSTEM
CONNECTOR
The unit (rear)
Subwoofer
Using the wireless subwoofer kit SWK-W16
Subwoofer
SWK-W16
1 2 3 4 5 6
PREPARATIONS ➤ d Other connections En 26
❑ Connecting the cables
1
Connect subwoofer cable to the SUBWOOFER OUT jack on the
SWK-W16 and the subwoofer’s input jack.
If the Yamaha subwoofer has a SYSTEM CONNECTOR jack, connect system
control cable to the SYSTEM CONNECTOR jack on the SWK-W16 and the
subwoofer’s SYSTEM CONNECTOR jack. When the unit is turned on and off,
the subwoofer turns on and off at the same time.
2
Plug the power cables for the subwoofer and the SWK-W16 into an
AC wall outlet.
When the unit is turned on, a wireless connection between the unit and
SWK-W16 will be established. The status indicator glows green once the
wireless connection is established.
• See “Troubleshooting” (p. 93, 99) if the indicator on the wireless subwoofer kit does not glow green.
❑ Configuring subwoofer output
Set subwoofer output to “Front/Wireless” (default setting) in the setup menu (p. 74).
The unit and the wireless subwoofer kit are automatically connected via wireless
connection when the unit is turned on, or when subwoofer output in the setup menu is
set to “Front/Wireless”.
• When using the Yamaha NS-SW300 subwoofer, adjusting subwoofer controls as follows is recommended.
(Adjustment values may be changed in accordance with the listening environment or personal
preferences.)
– Set VOL (volume) to 4.5
– Set HIGH CUT to 3.5
– Set PHASE to REV (reverse)
– Set B.A.S.S. to MOVIE
• Configure the subwoofer’s setting so that it turns on/off when the unit is turned on/off.
• The wireless subwoofer kit SWK-W16 cannot be used while the subwoofer is connected to the unit via
cables.
❑ Pairing the SWK-W16 with the unit
If the indicator on the SWK-W16 flashes red and no sound is coming from the
subwoofer during playback, move the SWK-W16 closer to the unit to improve
conditions for wireless communications, and follow the procedure below to pair the
SWK-W16 with the unit.
1
Set “Bass Out” for “Subwoofer” in the setup menu to “Front/
Wireless”.
2
Select “Pairing” for “Subwoofer” in the setup menu.
3
Use a pointed object, such as a ballpoint pen, to press and hold the
SUBWOOFER PAIRING button on the rear panel of the SWK-W16 for
three seconds.
SUBWOOFER
OUT
SYSTEM
CONNECTOR
2
1
1
2
INPUT
SYSTEM
CONNECTOR
To an AC
wall outlet
Subwoofer cable
(supplied)
To an AC wall outlet
System control cable
(supplied)
SWK-W16
Subwoofer
Status indicator
Rear side
SUBWOOFER
OUT
SYSTEM
CONNECTOR
SUBWOOFER
PAIRING
SUBWOOFER PAIRING button
1 2 3 4 5 6
PREPARATIONS ➤ e Connecting the power cable En 27
Wired network connections
For a wired connection, connect one end of the network cable to the NETWORK jack on
the rear panel of the unit and the other end to a router. For details, refer to
“NETWORKS” (p. 50).
After all the connections are complete, plug in the power cable.
e Connecting the power cable
SYSTEM
CONNCETOR
RL
AUX1
AUX2 TV OPTICAL
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-IN IR-OUT
UPDATE ONLY
RS-232C
SUBWOOFER
OUT
AC IN
The unit (rear)
To an AC wall outlet
1 2 3 4 5 6
PREPARATIONS ➤ f Initial settings En 28
Displaying the menu screen on the TV
Visual operation of this unit is
possible by displaying its menu
screen on the TV.
Turn on the unit and the TV, and
then use the input button on the
TV’s remote control to switch input
so that video input from this unit is
displayed.
When this unit and the TV are
connected as shown below,
select “HDMI 1” using the TV’s
remote control.
The menu display
The menu is displayed on the TV screen when the SETUP ( ) key
or OPTION ( ) key is pressed. When the TV is receiving HDMI
signals, the menu is superimposed over video content. Press the
SETUP ( ) key twice or OPTION ( ) key a second time to cancel
menu display.
• The setup menu (p. 67) can only be displayed on a TV screen. It cannot be shown
in the front panel display.
f Initial settings
TV remote control (example)
Switch
input
sources
SYSTEM
CONNCETOR
RL
AUX1
AUX2 TV OPTICAL IR-IN
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-OUT
UPDATE ONLY
RS-232C
NETWORK
SUBWOOFER
OUT
HDMI INPUT
123
OUT
(ARC)
HDMI
HDMI
TV
The unit (rear)
Setup Menu
Beam
Sound
HDMI
Display
Information
IntelliBeam
Horizontal Angle
Vertical Angle
Beam Travel Length
Focal Length
Image Location
Channel Out
Subwoofer
OPTION ( )
z
SETUP ( )
1 2 3 4 5 6
PREPARATIONS ➤ f Initial settings En 29
Selecting the language for menu display
1
Turn the unit and TV on.
2
Switch the TV’s input to display video input from this unit (p. 28).
3
Press and hold the SETUP ( ) key until the “OSD Language” menu
appears on the TV.
When the menu is not displayed
• Confirm the following cases.
– The HDMI input jack of your TV and the HDMI OUT (ARC) jack of the unit are connected.
– The input of your TV is set to “HDMI 1” (example).
4
Use the S/T key to select the desired language and press the
ENTER key.
Settings
, ENGLISH (default), DEUTSCH, FRANÇAIS, ESPAÑOL, ITALIANO, NEDERLANDS,
РУССКИЙ, SVENSKA, TÜRK
5
Press the SETUP ( ) key to exit the setup menu.
Initial screen display
When the unit is turned on for the first time after purchase, the screen below will be
displayed. (“ViewScreen” is shown in the front panel display.)
While this screen is displayed, an iOS device (such as an iPhone) can be used to
easily connect the unit to a wireless network. See the Quick Reference Guide for
more information.
If you will not use an iOS device to connect to a wireless network, press the RETURN
() key.
• You can use this function to connect to a wireless network at any time by selecting “Share Wi-Fi
Settings (iOS)” from the setup menu. However, be aware that if a different wireless network, or a
Bluetooth device, has already been configured, doing so will erase any previous settings.
• This screen will not be displayed if the unit is connected to a router via its NETWORK jack (wired
connection).
• Be aware that if the IntelliBeam microphone is connected while the screen shown above is displayed
(p. 30), setup will be canceled, and the screen will switch to the auto measurement screen.
Share Wi-Fi Settings
You can share the wireless
(Wi-Fi) settings of the
network with Sound Projector
using a device with iOS7 or
later.
[ENTER]:Start
[RETURN]:Cancel
[ ]:OSD Language
OSD Language
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
NEDERLANDS
РУССКИЙ
SVENSKA
TÜRK
PREPARATIONS ➤ f Initial settings En 30
Auto setup for appropriate surround effects (IntelliBeam)
First use the “IntelliBeam” function to adjust each channel so that this unit provides the
optimal viewing and listening environment.
• The AUTO SETUP procedure may not be run successfully if this unit is installed in one of the rooms
described in “Unrecommended listening environments” (p. 15).
• In order for this unit to provide the optimal listening environment, adjust each channel first using the
“IntelliBeam” function. The My Surround function can be used to enjoy rich surround sound in these types
of rooms as well. See “Channel Out” (p. 73) for more information.
• Do not connect the IntelliBeam microphone to an extension cable as doing so may result in an inaccurate
sound optimization.
1
Place the IntelliBeam microphone at your normal listening position.
❑ Assembling the supplied cardboard microphone stand
• Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam
microphone at the same height as your ears would be when you are seated.
• Position the IntelliBeam microphone so that it is parallel with the floor.
Make sure that there are no obstacles between the IntelliBeam microphone and the
walls in your listening room as these objects obstruct the path of sound beams.
However, any objects that are in contact with the walls will be regarded as a protruding
part of the walls.
Installing the IntelliBeam microphone
12
3
5
4
Remove
Fit in
Run through
Place horizontally
Fit in
IntelliBeam microphone
Upper limit
Within 1 m
Center height of
this unit
Cardboard
microphone stand
Within 1 m
Listening position
1.8 m or more
Lower limit
Center line
IntelliBeam microphone
Cardboard microphone stand
PREPARATIONS ➤ f Initial settings En 31
• Test tones output during measurement are loud. Perform AUTO SETUP when no children are around and
there is no possibility of their entering the listening room, as their hearing may be impaired.
• If there are curtains in your listening room, we recommend following the procedure below.
1. Open the curtains to improve sound reflection.
2. Run “Beam optimize only” (p. 33).
3. Close the curtains.
4. Run “Sound optimize only” (p. 33).
• Make sure that your listening room is as quiet as possible. For accurate measurement, turn off air
conditioner or other devices that make noises.
1
Turn the unit and your TV on.
• When a subwoofer is connected to the unit, turn on the subwoofer, and set the volume and crossover
frequency as shown below.
2
Switch TV input to display video input from this unit (p. 28).
3
Connect the IntelliBeam microphone to the INTELLIBEAM MIC jack
of the unit.
The screen below is displayed after connecting IntelliBeam microphone to the
unit.
“AUTO SETUP” in the “IntelliBeam” menu can automatically adjust the
following two settings.
“Beam optimize only” or “Sound optimize only” can be measured separately in
the setup menu (p. 33).
• Follow the instructions below and then leave the room. If you remain in the room, you may obstruct
the beam, or the microphone may pickup any sounds you make, possibly resulting in improper
measurement.
Using AUTO SETUP (IntelliBeam)
VOLUME
MIN MAX MIN
MAX
CROSSOVER
HIGH CUT
Set the volume to half Set the crossover frequency to maximum
Beam optimize
only
This feature optimizes the beam angle so that the parameter best
matches your listening environment.
Sound optimize
only
This feature optimizes sound quality for each channel by measuring
the acoustic characteristics of the listening environment.
INTELLIBEAM MIC
INTELLIBEAM MIC
IntelliBeam microphone
Cardboard microphone stand
AUTO SETUP
(PREPARATION & CHECK)
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from Sound Pro-
jector. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
PREPARATIONS ➤ f Initial settings En 32
4
Press the ENTER key to start the AUTO SETUP
procedure and then leave the room within 10
seconds.
If the AUTO SETUP procedure is complete, this unit rings
the chimes.
• The AUTO SETUP procedure takes about 3 minutes.
• To cancel the AUTO SETUP procedure after it is started, or if you do not
want to apply the results, press the RETURN ( ) key.
• If an error occurs, an error buzzer sounds and an error message is
displayed. For details on error messages, see “If an error message is
displayed” (p. 34).
5
Press the ENTER key.
The measurement results are applied and saved in the unit.
• You can save several measurement results by pressing
the SYSTEM MEMORY 1, 2, or 3 key.
When the SYSTEM MEMORY 1 key is pressed, “M1
Saving” is displayed, and settings are saved.
• If ambient noise is picked up after measurement begins,
an error message is displayed in the “AUTO SETUP
COMPLETE” screen prompting you to begin
measurement again. Press the ENTER key to exit the
error message screen, and begin measurement again.
• See page 45 for more information on the system memory function.
SHOW RESULT
MEASUREMENT COMPLETE.
ENVIRONMENT CHECK:Success
FRONT :Beam
SURROUND :Beam
SUBWOOFER:Wired
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
AUTO SETUP START
Will begin in 10 sec.
Please leave the room.
----------
[RETURN]:Cancel
The screen changes
automatically as measurement
progresses.
AUTO SETUP COMPLETE
Please remove the MIC
from Sound Projector
and the listening position.
Press [SYSTEM MEMORY] key
to save set-up in the memory.
SYSTEM
MEMORY
ENTER
RETURN ( )
PREPARATIONS ➤ f Initial settings En 33
6
Remove the IntelliBeam microphone.
The “AUTO SETUP COMPLETE” screen closes.
The IntelliBeam microphone is sensitive to heat, so should
not be placed anywhere where it could be exposed to direct
sunlight or high temperatures (such as on top of AV
equipment).
❑ AUTO SETUP via the setup menu
“Beam optimize only” or “Sound optimize only” can be measured
separately in the setup menu.
1
Place the IntelliBeam microphone at your normal
listening position, and press the SETUP ( ) key.
See “Installing the IntelliBeam microphone” (p. 30) for
instructions on positioning the IntelliBeam microphone.
2
Press the S/T key to select “Beam” and then press
the ENTER key.
3
Press the S/T key to select “IntelliBeam” and then
press the ENTER key.
4
Press the S/T key to select one of the items below
and then press the ENTER key.
Settings
5
Connect the IntelliBeam microphone to this unit
after “AUTO SETUP (PREPARATION & CHECK)”
screen is displayed.
For details on connecting IntelliBeam microphone, refer to
“Using AUTO SETUP (IntelliBeam)” (p. 31).
6
Follow steps 4, 5, and 6 under “Using AUTO SETUP
(IntelliBeam)” to configure settings, and then
remove the microphone.
• When the AUTO SETUP procedure is performed from the setup menu, the menu
selection screen of the setup menu appears. Press the SETUP ( ) key twice to
exit the setup menu.
INTELLIBEAM MIC
INTELLIBEAM MIC
Beam+Sound optimize
Select this optimization feature if you make
settings for the first time. This menu takes
about 3 minutes.
Beam optimize only
Use to optimize the beam angle so that the
parameter best matches your listening
environment. This menu takes about 1
minute.
Sound optimize only
Use to optimize the beam delay, volume,
and quality so that the parameters best
match your listening environment. This
menu takes about 2 minutes.
You must optimize the beam angle with
“Beam optimize only” before starting
“Sound optimize only”. Select this
optimization feature in the following cases:
• If you have opened or closed the curtains
in your listening room before using this
unit
• If you have manually set the beam angle
with “Beam optimize only”.
//
ENTER
SETUP ( )
PREPARATIONS ➤ f Initial settings En 34
❑ If an error message is displayed
If an error message is displayed on the TV screen, see “Error messages” below to determine the cause and resolve the problem. Follow the instructions displayed on the TV screen
to begin measurement again.
Error messages
Error message Cause Remedy
ERROR E-1 Please test in quieter environment. There is too much noise in your listening room.
Turn off devices, such as an air condition, that make noise, or
move the unit away from such devices.
You may want to choose certain hours during the day when
there is not much noise coming from outside.
ERROR E-2 No MIC detected. Please check MIC connection and re-try. The IntelliBeam microphone is disconnected.
Connect the IntelliBeam microphone to the INTELLIBEAM
MIC jack on the front of this unit and begin measurement
again.
ERROR E-3 Unexpected control is detected. Please re-try. Some other operations were performed on this unit.
Begin measurement again. Do not perform any other
operations with this unit during measurement.
ERROR E-4
Please check MIC position. MIC should be set in front of
Sound Projector. Please re-try.
The IntelliBeam microphone is not placed in front of this unit.
Position the IntelliBeam microphone in front of this unit and
begin measurement again.
ERROR E-5
Please check MIC position. MIC should be set above 1.8m/
6.0ft and re-try.
The IntelliBeam microphone is not placed in the right distance
from this unit.
Position the IntelliBeam microphone at a distance of more
than 1.8 m from this unit and begin measurement again.
ERROR E-6
Volume level is lower than expected. Please check MIC
position/connection and re-try.
The IntelliBeam microphone cannot collect the sound
produced by this unit.
Position the IntelliBeam microphone properly, check the
connection, and then begin measurement again.
ERROR E-7 Unexpected error happened. Please turn off and re-try. An internal system error occurred.
Press the z key to turn off this unit, then run AUTO SETUP
procedure again after turning this unit on.
ERROR E-9 Please check the connection with subwoofer. The subwoofer output signals cannot be recognized.
Confirm the connection between the wireless subwoofer kit
and subwoofer (p. 25), and begin measurement again.
PREPARATIONS ➤ f Initial settings En 35
Operating the unit by TV’s remote control (HDMI control)
HDMI control allows you to operate external devices via HDMI. If you connect a TV that
supports HDMI control to the unit with an HDMI cable, you can control the unit (such as
power and volume) with TV remote control operations. You can also control playback
devices (such as HDMI control-compatible BD/DVD players) connected to the unit with
an HDMI cable.
Coordinated functions via the TV remote control
In addition to the functions in the left column, the unit’s menus displayed on the TV can
be operated with some TV.
• Even if your TV supports the HDMI control function, some functions may not be available. For details, refer
to documentation supplied with your TV.
• We suggest using devices (TV, BD/DVD player, etc.) from the same manufacturer.
What is the HDMI control function?
Remote control of TV (Example)
1. Turn on/off
Both the TV and this unit turn on/off at the same time.
3. Switch the audio output device
(TV or this unit (amplifier))
4. Adjust volume
This unit's volume can be adjusted when the TV’s audio output is set
to this unit (amplifier).
2. Switch input sources
• The unit’s input source switches accordingly when the TV’s input
source is switched.
Examples
– When a TV program is selected on the TV, the unit’s audio input
source is switched to the HDMI OUT (ARC) jack using the ARC
function or TV jack.
– When a Blu-ray disc player connected to the HDMI IN 1 jack on the
unit is selected, the unit’s input source also switches to HDMI 1.
• The input source can be switched while the unit is off.
5. HDMI signal pass-through
HDMI input signals are output from the HDMI OUT (ARC) jack. Video and audio contents from an
HDMI input source are output from the TV when the unit is turned off.
6. ARC function
Audio signals output from the HDMI (ARC) jack on the TV can be input to the HDMI OUT (ARC)
jack on the unit (p. 22).
PREPARATIONS ➤ f Initial settings En 36
1
Turn on the unit, TV, and playback devices.
2
Activate the HDMI control function on the unit, TV,
and playback devices such as BD/DVD players that
support this function.
For this unit, set “HDMI Control” to “On”. The default setting
is “Off” (p. 77).
For playback devices, refer to documentation supplied with
each device.
3
Turn off the main power of the TV and then turn off
the unit and playback devices.
4
Turn on the unit and playback devices and then turn
on the TV.
5
Switch the TV input to display the video from the
unit.
6
Select HDMI 1-4 as an input source and confirm that
the video of the playback device is displayed on the
TV.
When the playback device is connected to the HDMI IN 1
jack, press the HDMI1 key.
7
Check that the unit is properly coordinated with the
TV by turning off the TV or adjusting the TV volume
with the TV remote control.
When changing connected devices, or the jacks via which devices
are connected, reconfigure settings as follows.
1
Disable the HDMI control function of the TV and BD/
DVD player, turn off all connected devices, and
change the connections.
2
Perform steps 1 to 7 of “Setting the HDMI control
function”.
Setting the HDMI control function
HDMI1
Input source name
If devices are not coordinated
Confirm the settings are properly configured as described
below.
– “HDMI Control” (p. 77) is set to “On” in the setup menu.
– The HDMI control function is enabled on the TV.
The example of TV settings
• From the setup menu on your TV, select “Link setting”
“HDMI control setting”, then set a setting such as “HDMI
control function” to “ON”.
• Set audio output to any option other than TV.
If devices fail to coordinate even after the settings described
above have been applied correctly:
– Turn off this unit and the TV, and then turn them back on again.
– Disconnect the power cable of the unit and external devices
connected to the unit via HDMI cable. Plug them in again after
about 30 seconds.
– If devices fail to coordinate after OPTICAL, AUX1, or AUX2 is
input, repeat steps 5 and 6 under “Setting the HDMI control
function”.
Changing the connection method and
connected devices
z
HDMI 1
PLAYBACK ➤ Basic operation for playback En 37
PLAYBACK
1
Press the z key to turn on this unit.
When the wireless subwoofer kit is connected to the unit,
the indicator on the wireless subwoofer kit glows green.
2
Turn on devices (TV, BD/DVD player, game console,
etc.) connected to this unit.
3
Select a device by pressing the input selector key or
NET key corresponding to the connection of
external devices.
Press the HDMI1 key to play audio/video content from a
BD/DVD player connected via the HDMI IN1 jack.
For playback from a Bluetooth device, refer to p. 46. For
audio playback via a network, refer to p. 61 to 66.
4
Play back a device selected in step 3.
5
Press the VOL (+/-) key to adjust the volume. Press
the SUB (+/-) key to adjust the volume of the
subwoofer.
• When audio is output from both TV speaker and this unit,
mute the TV sound.
• When sound input to HDMI IN jack is output from the TV,
the volume level does not change even if you press the
VOL (+/-) key or the MUTE ( ) key.
• To mute the sound, press the MUTE ( ) key. “MUTE
ON” is shown in the front panel display. To resume the
volume, press the MUTE ( ) key again or press VOL (+/
-) key. “MUTE OFF” is shown in the front panel display.
• The subwoofer volume can be adjusted separately from the whole volume.
• Lowering the subwoofer volume is recommended at night.
6
Select 3D surround playback, surround playback,
stereo playback, or target playback mode, and
configure sound setting according to your
preferences (p. 38).
Basic operation for playback
HDMI1
Input source name
Press the z key to turn off this unit after use.
MUTE ( )
VOL (+/
-
)
SUB (+/
-
)
z
NET
Input selector
keys
PLAYBACK ➤ Enjoying sound based on your preference En 38
This unit supports the following capabilities to enjoy sound based
on your preference.
• 3D surround playback mode
• Surround playback mode (p. 39)
• CINEMA DSP (p. 39)
• Stereo playback mode (p. 41)
• Target playback mode (p. 41)
• Compressed Music Enhancer (p. 42)
• CLEAR VOICE (p. 42)
• Volume adjustment for each channel (p. 43)
Playback with 3D surround sound
In addition to 5-channel sound beams used for surround sound
playback in the horizontal direction, surround sound can be heard
from above by directing two sound beams (from height channels)
upward and reflecting them off the ceiling. Compared to surround
sound playback in only the horizontal direction, this gives the
sound field (spatial expression with sounds) a greater sense of
immersion and reality.
1
Press the 3D SURROUND key to switch to 3D
surround mode.
“3D SUR.” is shown in the front panel display.
• Configuring Channel Out settings (p. 73) in the setup menu allows for more
precise configuration of beam settings in accordance with the audio source and
listening room setup.
Enjoying sound based on your preference
Sound beams in the horizontal direction
Sound beams output from height channels
Channels created from the front and rear sound
beams (p. 73)
3D SUR.
3D SURROUND
PLAYBACK ➤ Enjoying sound based on your preference En 39
Playback with surround sound
5-channel sound beams create a sound field for surround sound
playback without using height channel sound beams.
1
Press the SURROUND key to switch to surround
mode.
“SURROUND” is shown in the front panel display.
• Configuring Channel Out settings (p. 73) in the setup menu allows for more
precise configuration of beam settings in accordance with the audio source and
listening room setup.
• Use 3D surround sound playback mode for playback of audio fed via height
channels such as with Dolby Atmos.
Enjoying three-dimensional surround
sound (CINEMA DSP 3D/CINEMA DSP)
Select the desired CINEMA DSP program according to the audio
source and your preferences. Yamaha’s exclusive sound field
reproduction technology (CINEMA DSP 3D/CINEMA DSP) easily
reproduces realistic sound fields comparable to those found in
movie theaters and concert halls, allowing users to enjoy a natural
and three-dimensional listening environment.
Sound fields are reproduced using CINEMA DSP 3D for 3D
surround sound playback, and CINEMA DSP for surround sound
playback. The same programs can be selected for both CINEMA
DSP 3D and CINEMA DSP.
1
Press the CINEMA DSP (MOVIE, MUSIC, or
ENTERTAINMENT) key repeatedly to select the
desired program.
The CINEMA DSP program name appears in the front
panel display.
• The CINEMA DSP programs are not available in the following conditions.
– In stereo playback mode (p. 41) or target playback mode (p. 41)
– When using My Surround function (p. 74).
• This unit automatically memorizes the settings assigned to each input source.
When you select another input, the unit automatically recalls the last settings for
the selected input.
In addition to two-dimensional sound fields reproduced with
standard CINEMA DSP, CINEMA DSP 3D applies measured
three-dimensional sound field data, including vertical directional
information, for reproduction of three-dimensional sound fields.
Sound beams
Channels created from the front and rear sound
beams (p. 73)
SURROUND
CINEMA DSP 3D
CINEMA DSP
SURROUND
PLAYBACK ➤ Enjoying sound based on your preference En 40
❑ CINEMA DSP 3D/CINEMA DSP options
MOVIE (use the MOVIE key to select)
MUSIC (use the MUSIC key to select)
ENTERTAINMENT (use the ENTERTAINMENT key to select)
Playback without using CINEMA DSP (press the OFF key)
Sci-Fi
This program clearly reproduces dialogs and special
sound effects of the latest science fiction films and lets
you feel a broad and expansive cinematic space.
Adventure
This program reproduces the thrilling environment of the
latest action films and lets you feel the dynamic and
excitement of fast-moving scenes.
Spectacle
This program reproduces the wide and grand
environment and lets you have added impressions on
spectacular scenes with strong visual impacts.
Music Video
This program produces a vibrant environment and lets
you feel as if you are at an actual jazz or rock concert.
Concert
This program creates a rich surround effect of a large
round concert hall with a great deal of presence,
emphasizing the extension of sounds, and lets you feel as
if you are seated close to the center of the stage.
Jazz Club
This program recreates the acoustic environment of “The
Bottom Line”, a famous jazz club in New York once and
lets you feel as if you are seated right in front of the stage.
Sports
This program reproduces the energetic environment of
live sports broadcasting, converging a commentator’s
voice on the center and broadening the overall
atmosphere of the stadium, and lets you feel as if you are
seated at an actual stadium or a ball park.
Talk Show
This program reproduces excitement of live talk shows. It
enhances the ambience of gaiety while keeping the
conversations at a comfortable volume.
Drama
This program stables reverberations that match a wide
range of movie genres from serious dramas to musicals
and comedies, and offers an optimum 3D feeling,
reproducing effects tones and background music softly
but cubically around clear words.
Game
This program is suitable for role-playing and adventure
games. It utilizes the sound field effects for movies to
represent the depth and spatial feeling of the field during
play, while offering movie-like surround effects in the
movie scenes in the game.
DSP Off
Audio content is played in 3D surround mode or surround
mode when CINEMA DSP is not used.
CINEMA DSP
PLAYBACK ➤ Enjoying sound based on your preference En 41
2-channel playback (stereo playback mode)
2-channel stereo playback using the right front and left front
channels is enabled. When multi-channel audio signals are input,
they are down-mixed to 2 channels.
1
Press the STEREO key to switch to stereo playback
mode.
Delivering sound to a specified location
(target playback mode)
Target playback mode outputs sound beams from a single channel
for optimal listening from a specific position.
Refer to the illustrations below.
Play an input source, and adjust the beam angle.
1
Press the TARGET key.
2
Use the W/X key to adjust beam angle.
The angle to the left increases by 2 degrees each time the
W key is pressed; the angle to the right increases by 2
degrees each time the X key is pressed.
A maximum angle of 90 degrees in either direction is
possible.
Disabling target playback mode
Press the 3D SURROUND key, SURROUND key, or STEREO key to
turn target playback mode off.
• The CINEMA DSP programs are not enabled in target playback mode.
• Bass output is controlled to prevent sounds from spreading in other directions.
For listening at low volumes, such as at night
For clear sound at a distance
TARGET L16
Beam angle adjusted 16 degrees to the left
/
3D SURROUND
SURROUND
STEREO
TARGET
PLAYBACK ➤ Enjoying sound based on your preference En 42
Playing back digitally compressed formats
(such as MP3, etc.) with enriched sound
(Compressed Music Enhancer)
Play back digitally compressed formats such as MP3, with
emphasis on bass and treble for extended dynamic sounds.
1
Press the ENHANCER key to turn on the
Compressed Music Enhancer function.
Press the key again to turn off the function.
• Compressed Music Enhancer is disabled when digital audio signal with a
sampling rate greater than 48 kHz is input.
• By default, this function is set to “ON” when the input source is Bluetooth. It is set
to “OFF” with any other input source.
• This unit automatically memorizes the “ON” and “OFF” settings assigned to each
input source. When you select another input, the unit automatically recalls the last
settings for the selected input.
Clear playback of human voices
(CLEAR VOICE)
Human voices, such as lines in movies and TV shows, or news and
sports commentary, are played back very clearly.
1
Press the CLEAR VOICE key to turn on the CLEAR
VOICE function.
Press the key again to turn off the function.
Adjusting the position from which dialog is
heard (Dialog Lift)
When dialog sounds like it is coming from below the TV screen,
adjust the position upward so that it sounds as if it is coming from
the center of the TV screen.
1
Press the DIALOG LIFT key.
The current setting is displayed.
Display changes as follows each time the DIALOG LIFT key
is pressed.
0 (default) 1 2 3 0...
• The dialog lift function can be used with 3D surround sound playback and
surround sound playback (other than My Surround playback).
Dlg.Lift 0
3
2
1
0
ENHANCER
CLEAR VOICE
DIALOG LIFT
PLAYBACK ➤ Enjoying sound based on your preference En 43
Adjusting volume for each channel
Adjust the volume of playback for each channel (audio in each
direction) so that sounds are evenly distributed in their respective
directions.
• Refer to “Channel Level” (p. 75) when adjusting the volume of each channel with
the test sound.
1
Press the CH LEVEL key to select adjustable
channel from the followings.
FL: Front left
FR: Front right
C: Center
SL: Surround left
SR: Surround right
HL: Height left
HR: Height right
SW: Subwoofer
• Adjusting the channel level is not available in target playback mode.
• SW (subwoofer) volume can only be adjusted in stereo playback mode
(p. 41).
• Volume for the following channels can be adjusted when “My Surround” is
set to “On” (p. 74).
C: Center
SL/SR: Surround (left/right)
SW: Subwoofer
2
Press the S/T key to adjust the volume.
Adjustable range: -20 to +20
Example of volume balance
• If you have problems hearing words: Select C (center) to increase the level.
When the sound is not like surround sound: Select SL (surround left), SR
(surround right), HL (height left) or HR (height right) to increase the level.
• The volume of the subwoofer also can be adjusted by using the SUB (+/-) key.
FL FR
SW
C
HL HR
SL SR
/
SUB (+/
-
)
CH LEVEL
PLAYBACK ➤ Using useful features En 44
Saving energy with the Eco function
Using the Eco function to reduce the amount of power consumed
by this unit.
When this function is enabled, the brightness of the front panel
display is minimized and the maximum volume is reduced.
1
Press the ECO key.
“ECO ON” is displayed and the front panel display turns off.
The brightness of STATUS indicator is minimized.
Disabling the Eco function
Press the ECO key.
“ECO OFF” is displayed in the front panel display.
• Disable this function for louder playback.
• When this function is enabled, “Dimmer” in the setup menu (p. 78) and “MAX
VOLUME” in the advanced setup menu (p. 87) cannot be configured.
Switching information displayed in the
front panel display
Information regarding the input source, surround sound, and
subwoofer is displayed.
1
Press the INFO ( ) key.
Display changes as follows each time the INFO ( ) key is
pressed. The information varies according to the input
source.
• Display in playback mode (Beam)
– 3D SUR.: Playback in 3D surround mode (p. 38)
– SURROUND: Playback in surround mode (p. 39)
– MY SUR.: Playback using the My Surround function (p. 74)
– STEREO: Stereo playback (p. 41)
– TARGET: Playback in target playback mode (p. 41)
• Subwoofer status display (SUB Status)
– Wireless: The unit is connected to the wireless subwoofer kit (p. 25).
– None: No subwoofer is connected to the unit.
– Wired: When “Bass Out” in the setup menu is set to “Wired” (p. 74).
Using useful features
ECO ON
Input: Name of the input source
(“BLUETOOTH”, or the name of the connected
device, is displayed with Bluetooth input.)
T
Beam: Playback mode
T
Decoder: Current decoder (p. 76)
T
Cinema DSP: CINEMA DSP program (p. 39)
T
SUB Status: Subwoofer status
T
INFO ( )
ECO
PLAYBACK ➤ Using useful features En 45
Saving this unit’s settings to system memory
Three sets of settings can be saved to this unit’s memory, enabling
quick loading of settings optimized for specific listeners or
environmental changes as needed. Refer to the examples below to
save IntelliBeam measurement results and settings such as
surround setting to system memory, or to load a pre-defined
settings.
Example 1 Saving the IntelliBeam measurements for different
environments to system memory
If materials that absorb sound, such as curtains, obstruct sound
beams, the effectiveness of those beams decreases. Measure with
the curtains open and again with them closed. Save both sets of
settings to SYSTEM MEMORY 1 and 2, and load the appropriate
settings as needed.
Example 2 Saving frequently used settings to system memory
SYSTEM MEMORY 1: Surround setting
SYSTEM MEMORY 2: A target playback mode setting that
projects sound beams toward the kitchen
SYSTEM MEMORY 3: A target playback mode setting that
projects sound beams toward the living
room
Example 3 Saving preferred listener settings to system
memory
SYSTEM MEMORY 1: Settings configured for Dad
SYSTEM MEMORY 2: Settings configured for Mom
SYSTEM MEMORY 3: Settings configured for parties
The following settings can be saved to system memory.
• IntelliBeam measurement results (p. 31)
See page 33 for instructions on saving measurement results for
IntelliBeam.
(When “Horizontal Angle”, “Vertical Angle”, “Beam Travel Length”,
“Focal Length”, “Image Location”, and “Channel Level” are
configured in the setup menu (p. 67), these settings are applied
to IntelliBeam’s AUTO SETUP measurements.)
• 3D surround playback (p. 38), surround playback (p. 39), stereo
playback (p. 41), or target playback mode (p. 41)
(The Channel Out settings (p. 73) can also be saved for 3D
surround/surround playback mode.)
• Surround: CINEMA DSP 3D/CINEMA DSP (p. 39)
• Tone control (p. 85)
• Subwoofer settings (p. 74)
1
Hold down the SYSTEM MEMORY 1, 2, or 3 key until
“M1 Save?”, “M2 Save?”, or “M3 Save?”,
corresponding to the button pressed, is displayed.
2
Press the same SYSTEM MEMORY key again.
When the SYSTEM MEMORY 1 key is pressed, “M1
Saving” is displayed, and settings are saved.
• If system settings are already stored in the selected memory number, this
unit overwrites the old settings.
• The memory function cannot be set when “MEMORY PROTECT” is set to
“ON” in the advanced setup menu (p. 86).
1
Press the SYSTEM MEMORY 1, 2, or 3 key
corresponding to settings to be loaded.
If the SYSTEM MEMORY 1 key is pressed, “M1 Load?” will
be displayed.
2
Press the same SYSTEM MEMORY key again.
When the SYSTEM MEMORY 1 key is pressed, “M1
Loading” is displayed, and settings are loaded.
Saving settings to system memory
Loading settings
SYSTEM
MEMORY
PLAYBACK ➤ Wireless playback of audio via Bluetooth connection En 46
The unit can be used to receive and play audio from a Bluetooth device, and to transmit
audio for playback on a Bluetooth device.
See documentation supplied with your Bluetooth device for more information.
❑ Receiving audio from a Bluetooth device
Audio from a Bluetooth device, such as a mobile device or a digital music player, can
be played over a wireless connection.
❑ Transmitting audio to a Bluetooth device
Use Bluetooth wireless headphones and the like to listen to audio.
• Audio cannot be received by the unit from mobile devices and the like, and transmitted to speakers or
headphones at the same time.
• “Bluetooth” in the setup menu must be set to “On” (default; p. 83) to use Bluetooth functions.
•A Bluetooth device that has been assigned a passkey (PIN) other than “0000” cannot be connected to the
unit.
• The unit can connect to up to 20 Bluetooth devices for receiving and transmitting audio. If a new device is
successfully connected to the unit after 20 other devices have already been connected, the device
information with the earliest connection date (the first device connected) will be erased to make room for
the new device.
• Be sure that the Bluetooth device is no farther than 10 m from the unit when connecting the two.
• Refer to “Bluetooth” (p. 95) in “Troubleshooting” if a Bluetooth connection cannot be established.
•Adjust Bluetooth device volume as needed.
Wireless playback of audio via Bluetooth connection
Bluetooth device (such as a
mobile device)
The unit
The unit
Bluetooth speakers/
headphones
PLAYBACK ➤ Wireless playback of audio via Bluetooth connection En 47
Listening to music from a
Bluetooth
device (Receiving)
1
Press the key on the remote control.
Bluetooth is selected as an input source, and
“BLUETOOTH” is shown in the front panel display.
• If a Bluetooth device has been connected before, the unit will connect to the
last connected device when the key is pressed. Terminate this
connection to connect a new device.
• If you are unable to select Bluetooth as an input source, be sure that
“Transmission” in the setup menu is set to “Off” (p. 83)
2
Turn on the Bluetooth function on the Bluetooth
device.
The operation varies depending on the device. Refer to
documentation supplied with the device.
3
Select “YSP-5600” in the Bluetooth device list on
the device.
If a passkey (PIN) is required, enter the number “0000”.
The indicator in the front panel display flashes while the
unit and Bluetooth device are being connected, and glows
steadily when the connection is established.
“Connect” is shown in the front panel display.
The indicator or a completion message is displayed on
the Bluetooth device.
4
Play back a song on the Bluetooth device.
• With some Bluetooth devices, this unit must be specified as the destination for
audio output.
• Setting “Network Standby” in the setup menu to “On” allows the unit to be turned
on and off with Bluetooth device operations (p. 82).
BLUETOOTH
YSP-5600
PIN 0 0 0 0
123
456
7 8 9
0
Flashes while
processing a
connection
Glows when the
connection is
established
PLAYBACK ➤ Wireless playback of audio via Bluetooth connection En 48
Bluetooth connection is terminated in the following cases.
The indicator on the unit’s front panel turns off when the
connection is terminated.
•The Bluetooth function is turned off on the Bluetooth device.
• The key is pressed for more than 3 seconds.
• The unit is turned off.
• When Bluetooth connection is terminated, “Disconnected” is shown in the front
panel display.
Terminating Bluetooth connection
PLAYBACK ➤ Wireless playback of audio via Bluetooth connection En 49
Listening to audio through
Bluetooth
speakers or headphones (transmitting)
• Music input using AirPlay cannot be output to Bluetooth devices.
1
Turn on the Bluetooth device.
2
Select the input source (other than Bluetooth) with
the input selector keys.
3
Press the SETUP ( ) key twice.
The setup menu is displayed on the TV screen.
4
Use the S/T keys to select “Bluetooth”, and then
press the ENTER key.
5
Use the S/T keys to select “Transmission”, and
then press the ENTER key.
6
Use the S/T keys to select “On”, and then press
the ENTER key.
7
Use the S/T keys to select “Device Search”, and
then press the ENTER key.
8
Use the S/T keys to select a Bluetooth device, and
then press the ENTER key.
The indicator in the front panel display flashes while the
unit and Bluetooth device are being connected, and glows
steadily when the connection is established.
“Completed” is shown in the front panel display.
9
Play an audio source, and enjoy music via the
Bluetooth device.
• “Not found” is displayed on the screen with step 8 if the unit was unable to find a
device to which to connect.
• “No Device Name” replaces the device name on the screen with step 8 if the unit
is unable to recognize the name of the device.
• Audio will also be output from the unit.
Bluetooth connection is terminated in the following cases.
The indicator on the unit’s front panel turns off when the
connection is terminated.
• The connection is terminated from the Bluetooth device, or
the Bluetooth device is turned off.
• “Transmission” in the setup menu is set to “Off”.
• The unit is turned off.
▲
ABCDE 1
FGHIJ 2
abcde 3
fghij 4
▼
[ENTER]:Confirm
[RETURN]:Cancel
Device Search
Terminating Bluetooth connection
Flashes while
processing a
connection
Glows when the
connection is
established
/
ENTER
SETUP ( )
Input selector
keys
NETWORKS ➤ Network functions En 50
NETWORKS
Network connection allows you to listen to Internet radio stations or music streaming
services, and play music files with AirPlay or your computer (media service) via this
unit.
Depending upon the input source, the mobile app, MusicCast CONTROLLER, may be
required. Playback that requires the MusicCast CONTROLLER is indicated with the
icon.
• Playing music files stored on media servers or mobile devices
PC or DNLA-compatible NAS p. 61
AirPlay p. 64
Mobile devices p. 66
• Listening to Internet radio p. 62
Internet radio stations can be selected once they are registered with the unit.
• Transmit and receive audio to/from other MusicCast-enabled devices
connected to your home network.
Refer to the supplied “MusicCast Setup Guide” for details.
• See our website for more information on the MusicCast CONTROLLER app.
• The input source switches automatically when music is played over a network. Use the NET key to switch to
a different input source. The input source changes as follows each time the NET key is pressed.
Network functions
X SERVER X NET RADIO X AirPlay X X MusicCast LinkMusic streaming service
(if available)
NETWORKS ➤ Connecting to a network En 51
You can choose between wired network connection and wireless network connection depending upon your network environment.
• Some security software installed on your computer, or network device settings (such as a firewall), may
block the unit’s access to your computer or Internet radio stations. Should this occur, change security
software and/or network device settings.
• A network connection cannot be established if the MAC address filter on your router is enabled. Check your
router’s settings.
• To configure your router’s subnet mask manually, apply the same subnet used by this unit to all devices.
• Use of a broadband connection is recommended when using Internet services.
• If your router supports DHCP, network settings for the unit need not be configured. Network parameters
(such as the IP address) will be assigned automatically. If your router does not support DHCP, or if you
prefer to configure network parameters manually, you must configure network settings yourself (p. 81).
• You can verify that network parameters (such as the IP address) have been properly assigned to the unit by
selecting “Information” (p. 79) from the setup menu.
Connecting to a network
Does the router support a wireless
connection?
Do you use the dedicated app,
MusicCast CONTROLLER, on
your mobile device?
Wireless network (using the MusicCast CONTROLLER app)
Refer to the supplied “MusicCast Setup Guide”.
Use a wired network.
Is your iOS device running iOS
7.1 or later?
Wireless network (sharing iOS device settings)
p. 52 Use an iOS device (such as an iPhone) to apply network settings (p. 53).
Is your wireless router equipped
with a WPS button?
Wireless network (using the WPS button)
Use the WPS button on your wireless router (access point) (p. 54).
Does your wireless router
support entry of a WPS PIN
code?
Wireless network (using the WPS PIN code)
Register the unit’s PIN code with your wireless router (access point) (p. 58).
Wireless network (searching for an access point)
Select an access point from a list of available access points (p. 54).
Wireless network (configuring a wireless connection manually)
Enter required information, such as the SSID, manually (p. 56).
Ye s
Ye s
No, or a wired connection is preferred.
No, not sure yet
If the connection was not successful...
Ye s
If the connection was not successful...
No, not sure yet
If the connection was not successful...
If the connection was
not successful...
Ye s
No, not sure yet
Ye s
No, not sure yet
If the connection was not successful...
Wireless connection fails, or no access point is displayed.
NETWORKS ➤ Connecting to a network En 52
Wired network connections
To use a wired network connection, connect the unit to a router via an STP network
cable (category 5 or higher straight cable; not supplied).
• If the unit is already connected to a wireless network and you would like to switch to a wired connection,
change “Network” in the setup menu to “Wired”.
Wireless network
Connect the unit to a wireless router (access point).
The indicator on the front panel glows when the unit is connected to a wireless
network.
• You cannot use the wireless network connection simultaneously with the wired network connection (p. 52)
or Wireless Direct (p. 59).
• If the unit and the wireless router (access point) are too far apart, the unit may not connect to a wireless
router (access point). In such case, place them close to each other.
• If the unit will not be connected to a wireless router (access point), Wireless Direct (p. 59) can be used to
connect the unit directly to a mobile device to control the unit using the HOME THEATER CONTROLLER
(WLAN) app installed on that mobile device.
SYSTEM
CONNCETOR
AUX2 TV OPTICAL
IN 1
(HDCP2.2)
IN 2
IN 3
IN 4
OUT
(ARC)
HDMI
IR-IN IR-OUT
UPDATE ONLY
RS-232C
NETWORK
SUBWOOFER
OUT
RL
AUX1
NETWORK
LAN
WAN
The unit (rear)
Internet
Network Attached Storage
(NAS)
PC
Modem
Mobile device
Router
Network cable
The unit
Internet
Modem
Mobile device
Wireless router
(access point)
Glows (green)
NETWORKS ➤ Connecting to a network En 53
You can easily setup a wireless connection by applying the
connection settings on iOS devices (such as an
iPhone).
Before proceeding, confirm that your iOS device is connected to a
wireless router (access point).
• You need iOS device with iOS 7.1 or later.
• The connection settings on iOS devices cannot be applied to the unit to establish
a wireless connection if your wireless router (access point) uses WEP encryption.
See “Searching for a wireless router (access point)” (p. 54) to establish a
connection.
1
Press the z key to turn on this unit.
2
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 28).
3
Press the SETUP ( ) key twice.
The setup menu is displayed on the TV screen.
4
Use the S/T keys to select “Network”, and then
press the ENTER key.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
6
Use the S/T keys to select “Wireless (Wi-Fi)”, and
then press the ENTER key.
7
Use the S/T keys to select “Share Wi-Fi Settings
(iOS)”, and then press the ENTER key.
8
When the following screen is displayed, press the
ENTER key.
• The settings to be deleted (initialized) will be displayed. If you do not want to
delete these settings, press the RETURN ( ) key to terminate the
connection.
9
When the following screen is displayed, press the
ENTER key.
Sharing the iOS device setting
Network Connection
Wired
Wireless(Wi-Fi)
Wireless Direct
Wireless(Wi-Fi)
Select a setup method.
·WPS Button
·Share Wi-Fi Settings (iOS)
·Access Point Scan
·Manual Setting
·PIN Code
[ENTER]:OK
[RETURN]:Cancel
Share Wi-Fi Settings
If Sharing is begun, the
following settings will be
initialized.
·Network settings
·NET presets
·All music service account
information
·Bluetooth settings
[ENTER]:Start
[RETURN]:Cancel
Share Wi-Fi Settings
Make sure your iOS device is
connected to your Wi-Fi
network, and then open the
Wi-Fi settings screen of
your iOS device.
[ENTER]:Confirm
[RETURN]:Cancel
z
/
ENTER
SETUP ( )
RETURN ( )
NETWORKS ➤ Connecting to a network En 54
10
Display the Wi-Fi setup screen on the iOS device
and select the unit from “SETUP A NEW AIRPLAY
SPEAKER...”.
Follow the on-screen instructions displayed on the iOS
device.
You can easily set up a wireless connection with one push of the
WPS button on the wireless router (access point).
1
Press the z key to turn on this unit.
2
Press and hold the WPS key on the remote control
for at least 3 seconds.
“Press WPS button on Access Point” will be displayed in the
front panel display.
• To cancel configuration, press any key other than the WPS key.
3
Push the WPS button on the wireless router (access
point).
When a connection has been established, “Completed” will
be displayed in the front panel display.
If “NotConnect” is displayed, repeat the procedure from
step 1 again, or see the information below to try another
connection method.
• The WPS button cannot be used to establish a wireless connection if your
wireless router (access point) uses WEP encryption, or if the router’s MAC
address filter is enabled. See “Searching for a wireless router (access point)”
(p. 54) to establish a connection.
• The WPS button cannot be used to establish a wireless connection if your
wireless router (access point) is configured so that it does not broadcast its SSID.
See “Setting up the wireless connection manually” (p. 56) to establish a
connection.
• “WPS Button” under “Wireless (Wi-Fi)” in the setup menu can also be used to
configure a connection using the WPS button. Follow the on-screen instructions.
Find and connect to a nearby wireless router (access point).
1
Press the z key to turn on this unit.
2
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 28).
3
Press the SETUP ( ) key twice.
The setup menu is displayed on the TV screen.
4
Use the S/T keys to select “Network”, and then
press the ENTER key.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
Using the WPS push button configuration
About WPS
WPS (Wi-Fi Protected Setup) is a standard established by the
Wi-Fi Alliance, which allows easy establishment of a wireless
home network.
Searching for a wireless router (access
point)
Wireless(Wi-Fi)
Select a setup method.
·WPS Button
·Share Wi-Fi Settings (iOS)
·Access Point Scan
·Manual Setting
·PIN Code
[ENTER]:OK
[RETURN]:Cancel
z
/
ENTER
SETUP ( )
WPS
NETWORKS ➤ Connecting to a network En 55
6
Use the S/T keys to select “Wireless (Wi-Fi)”, and
then press the ENTER key.
7
Use the S/T keys to select “Access Point Scan”,
and then press the ENTER key.
The list of available access points appears on the TV
screen.
8
Use the S/T keys to select the desired access point
and press the ENTER key.
The wireless connection setting screen appears on the TV.
9
Press the ENTER key.
10
Use the W/X/S/T and ENTER keys to enter the
security key.
Once the security key been entered, select “OK”, and then
press the ENTER key. The screen will return to that
displayed in step 8.
11
Use the S/T keys to select “Connect” and press the
ENTER key to start the connection process.
When a connection has been established, “Completed” will
be displayed on the TV screen.
If “Not connected” is displayed press the ENTER key to
repeat the process beginning with step 6, or see the
information below to try another connection method.
• “Access Point Scan” cannot be used to establish a wireless connection if
your wireless router (access point) is configured so that it does not
broadcast its SSID. See “Setting up the wireless connection manually”
(p. 56) to establish a connection.
12
Press the SETUP ( ) key to exit the setup menu.
Network Connection
Wired
Wireless(Wi-Fi)
Wireless Direct
Wireless(Wi-Fi)
Select a setup method.
·WPS Button
·Share Wi-Fi Settings (iOS)
·Access Point Scan
·Manual Setting
·PIN Code
[ENTER]:OK
[RETURN]:Cancel
Access Point Scan
▲
SSID : Access Point 1
Security: WPA2-PSK(AES)
Security Key
:
Connect
▼
[ENTER]:Confirm
[RETURN]:Cancel
*****_
( ) [ ] { } < > * ! ? # % &
. , : ; _ | / \ $ ~ ^ ' " `
0 1 2 3 4 5 6 7 8 9 @ + - =
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m ←
n o p q r s t u v w x y z →
Space BKSP DELETE CLEAR
OK
CANCEL
[]/[]: Move the cursor left and right.
[Space]: Enter a space.
[BKSP]: Delete the character to the left of the selected one.
[DELETE]: Delete the selected character.
[CLEAR]: Delete all characters entered.
[CANCEL]: Cancel character entry, and return to the previous screen.
///
ENTER
SETUP ( )
NETWORKS ➤ Connecting to a network En 56
Setup the SSID (network name), encryption method and security
key for your network manually.
1
Press the z key to turn on this unit.
2
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 28).
3
Press the SETUP ( ) key twice.
The setup menu is displayed on the TV screen.
4
Use the S/T keys to select “Network”, and then
press the ENTER key.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
6
Use the S/T keys to select “Wireless (Wi-Fi)”, and
then press the ENTER key.
7
Use the S/T keys to select “Manual Setting”, and
then press the ENTER key.
8
Use the S/T keys to select “SSID”.
9
Use the W/X/S/T keys and the ENTER key to enter
the SSID of the access point.
Once the security key been entered, select “OK”, and then
press the ENTER key. The screen will return to that
displayed in step 8.
10
Use the S/T keys to select “Security” and the W/X
keys to select the encryption method.
Settings
None, WEP, WPA2-PSK (AES), Mixed Mode
• As communications are not encrypted when “None” is selected, selecting
this option poses the risk that third parties may access the unit without your
permission.
Setting up the wireless connection
manually
Network Connection
Wired
Wireless(Wi-Fi)
Wireless Direct
Wireless(Wi-Fi)
Select a setup method.
·WPS Button
·Share Wi-Fi Settings (iOS)
·Access Point Scan
·Manual Setting
·PIN Code
[ENTER]:OK
[RETURN]:Cancel
Manual Setting
▲
SSID :
Security: None
Security Key
:
Connect
▼
[ENTER]:Confirm
[RETURN]:Cancel
abc_
( ) [ ] { } < > * ! ? # % &
. , : ; _ | / \ $ ~ ^ ' " `
0 1 2 3 4 5 6 7 8 9 @ + - =
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m ←
n o p q r s t u v w x y z →
Space BKSP DELETE CLEAR
OK
CANCEL
[]/[]: Move the cursor left and right.
[Space]: Enter a space.
[BKSP]: Delete the character to the left of the selected one.
[DELETE]: Delete the selected character.
[CLEAR]: Delete all characters entered.
[CANCEL]: Cancel character entry, and return to the previous screen.
z
///
ENTER
SETUP ( )
NETWORKS ➤ Connecting to a network En 57
11
Use the S/T keys to select “Security Key” and
press the ENTER key.
• If you select “None” in step 10, this item is not available.
12
Use the W/X/S/T and ENTER keys to enter the
security key.
If you select “WEP” in step 10, enter either 5 or 13
character string, or 10 or 26 hexadecimal (base 16) keys.
If you select the method other than “WEP”, enter either 8 to
63 character string, or 64 hexadecimal (base 16) keys.
• Hexadecimal (base 16) keys use combinations of the numbers 0 through 9
and the letters a through f. Letters are not case sensitive.
Once the security key been entered, select “OK”, and then
press the ENTER key. The screen will return to that
displayed in step 8.
13
Use the S/T keys to select “Connect” and press the
ENTER key to start the connection process.
When a connection has been established, “Completed” will
be displayed on the TV screen.
If “Not connected” is displayed press the ENTER key to
repeat the process beginning with step 6.
14
Press the SETUP ( ) key to exit the setup menu.
*****_
( ) [ ] { } < > * ! ? # % &
. , : ; _ | / \ $ ~ ^ ' " `
0 1 2 3 4 5 6 7 8 9 @ + - =
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m ←
n o p q r s t u v w x y z →
Space BKSP DELETE CLEAR
OK
CANCEL
[]/[]: Move the cursor left and right.
[Space]: Enter a space.
[BKSP]: Delete the character to the left of the selected one.
[DELETE]: Delete the selected character.
[CLEAR]: Delete all characters entered.
[CANCEL]: Cancel character entry, and return to the previous screen.
///
ENTER
SETUP ( )
NETWORKS ➤ Connecting to a network En 58
Register the unit’s PIN code with your wireless router (access point)
to establish a connection. This procedure applies if your wireless
LAN router (access point) supports the WPS PIN feature.
1
Press the z key to turn on this unit.
2
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 28).
3
Press the SETUP ( ) key twice.
The setup menu is displayed on the TV screen.
4
Use the S/T keys to select “Network”, and then
press the ENTER key.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
6
Use the S/T keys to select “Wireless (Wi-Fi)”, and
then press the ENTER key.
7
Use the S/T keys to select “PIN Code”, and then
press the ENTER key.
The list of available access points appears on the TV
screen.
8
Use the S/T keys to select the desired access point
and press the ENTER key.
The PIN code of the unit appears on the TV screen.
9
Enter the unit’s PIN code into the wireless router
(access point).
For details on settings, refer to documentation supplied with
the wireless router (access point).
10
Press the ENTER key to start the connection
process.
When a connection has been established, “Completed” will
be displayed on the TV screen.
If “Not connected” is displayed press the ENTER key to
repeat the process beginning with step 6, or see the
information below to try another connection method.
• The PIN code cannot be used to establish a wireless connection if your
wireless router (access point) uses WEP encryption, or if the router’s MAC
address filter is enabled. See “Searching for a wireless router (access
point)” (p. 54) to establish a connection.
11
Press the SETUP ( ) key to exit the setup menu.
Using the WPS PIN code
Network Connection
Wired
Wireless(Wi-Fi)
Wireless Direct
Wireless(Wi-Fi)
Select a setup method.
·WPS Button
·Share Wi-Fi Settings (iOS)
·Access Point Scan
·Manual Setting
·PIN Code
[ENTER]:OK
[RETURN]:Cancel
PIN Code
PIN Code:00000000
Enter the PIN code
into the access point.
Press ENTER to start
the connection process.
[ENTER]:Start
[RETURN]:Cancel
z
///
ENTER
SETUP ( )
NETWORKS ➤ Connecting to a network En 59
Connecting a mobile device to the unit directly (Wireless Direct)
Connect a mobile device directly to the unit without using a wireless
router (access point).
Wireless Direct supports the following.
– Operation of the unit using a mobile device to which the
dedicated MusicCast CONTROLLER or HOME THEATER
CONTROLLER (WLAN) app has been installed.
– Use of AirPlay to play music files stored on an iOS device.
• You cannot use Wireless Direct simultaneously with the wired network connection
(p. 52) or the wireless network connection (p. 52).
• When Wireless Direct is enabled, the unit cannot connect to the Internet.
Therefore, you cannot use any kind of Internet service such as Internet radio.
1
Press the z key to turn on this unit.
2
Turn on the TV and switch the TV input to display
video from the unit (HDMI OUT jack; p. 28).
3
Press the SETUP ( ) key twice.
The setup menu is displayed on the TV screen.
4
Use the S/T keys to select “Network”, and then
press the ENTER key.
5
Use the S/T keys to select “Network Connection”,
and then press the ENTER key.
6
Use the S/T keys to select “Wireless Direct”, and
then press the ENTER key.
7
Use the S/T keys to select “Security” and the W/X
keys to select the encryption method.
Settings
None, WPA2-PSK (AES)
In most cases, “WPA2-PSK (AES)” should be selected. If
your mobile device does not support “WPA2-PSK (AES)”,
select “None”.
• As communications are not encrypted when “None” is selected, selecting
this option poses the risk that third parties may access the unit without your
permission.
8
Use the S/T keys to select “Security Key” and
press the ENTER key.
• If you select “None” in step 7, this item is not available.
The unit
Mobile device
Network Connection
Wired
Wireless(Wi-Fi)
Wireless Direct
z
///
ENTER
SETUP ( )
NETWORKS ➤ Connecting to a network En 60
9
Use the W/X/S/T and ENTER keys to enter the
security key.
Enter either 8 to 63 character string, or 64 hexadecimal
(base 16) keys.
• Hexadecimal (base 16) keys use combinations of the numbers 0 through 9
and the letters a through f. Letters are not case sensitive.
Once the security key been entered, select “OK”, and then
press the ENTER key. The screen below will be displayed.
• Before proceeding to the next step, record the following information. These
information will be needed to configure the Wi-Fi setting of a mobile device.
– SSID displayed on the TV screen
– Security key you have just entered
10
Use the S/T keys to select “Save” and press the
ENTER key to save the setting.
This completes the settings and “Set the mobile device.”
will be displayed on the TV screen. The unit functions as an
access point.
Next, configure the Wi-Fi settings of a mobile device.
11
Configure the Wi-Fi settings of a mobile device.
For details on settings of your mobile device, refer to
documentation supplied with the mobile device.
a Enable the Wi-Fi function on the mobile device.
b Select the SSID displayed in step 9 from the list of available
access points.
c When you are prompted for a password, enter the security key
displayed in step 9.
12
Press the SETUP ( ) key to exit the setup menu.
*****_
( ) [ ] { } < > * ! ? # % &
. , : ; _ | / \ $ ~ ^ ' " `
0 1 2 3 4 5 6 7 8 9 @ + - =
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m ←
n o p q r s t u v w x y z →
Space BKSP DELETE CLEAR
OK
CANCEL
[]/[]: Moves the cursor left and right.
[Space]: Enter a space.
[BKSP]: Delete the character to the left of the selected one.
[DELETE]: Delete the selected character.
[CLEAR]: Delete all characters entered.
[CANCEL]: Cancel character entry, and return to the previous screen.
Wireless Direct
▲
SSID : YSP-5600 XXXXXX
Security: WPA2-PSK(AES)
Security Key
: *************
Save
▼
[ENTER]:Confirm
[RETURN]:Cancel
///
ENTER
SETUP ( )
NETWORKS ➤ Playing back music stored on media servers (PCs/NAS) En 61
You can play back music files stored on your PC or DLNA-compatible NAS on the unit.
• To use this function, the unit and your PC must be connected to the same router (p. 51). You can check
whether the network parameters (such as the IP address) are properly assigned to the unit in “Information”
(p. 79) in the setup menu.
• The audio may be interrupted while using the wireless network connection. In this case, use the wired
network connection.
• The following file formats are supported.
– The unit supports playback of WAV (PCM format only), AIFF, MP3, WMA, MPEG-4 AAC, FLAC and
ALAC (Apple Lossless Audio Codec) files (1- or 2-channel audio only).
– The unit is compatible with sampling rates of up to 192 kHz for WAV, AIFF and FLAC files, 96 kHz for
ALAC files, and 48 kHz for other files.
– The unit supports gapless playback of WAV, FLAC and ALAC files.
– To play back FLAC files, you need to install server software that supports sharing of FLAC files via DLNA
on your PC or use a NAS that supports FLAC files.
– Digital Rights Management (DRM) contents cannot be played back.
Media sharing setup
To play back music files stored on your PC or DLNA-compatible NAS, first you need to
configure the media sharing setting on each music server.
This unit supports Windows Media Player 11 or later. This section explains Windows
Media Player 12 setup as an example.
1
Start Windows Media Player 12 on your PC.
2
Select “Stream”, then “Turn on media streaming”.
3
Click “Turn on media streaming”.
4
Select “Allowed” from the drop-down list next to the unit’s model
name.
5
Click “OK” to exit.
Refer to documentation supplied with the device or software and configure the media
sharing settings.
Playing music files
Use the MusicCast CONTROLLER app installed on your mobile device to play music
files.
• Configure basic settings for the MusicCast CONTROLLER app before playing music files.
• Refer to the supplied “MusicCast Setup Guide” for details.
Playing back music stored on media servers (PCs/NAS)
For a PC with Windows Media Player installed
For a PC or a NAS with other DLNA server software
installed
NETWORKS ➤ Listening to Internet radio En 62
You can listen to Internet radio stations from all over the world.
• To use this function, the unit must be connected to the Internet (p. 51). You can check whether the network parameters (such as the IP address) are properly assigned to the
unit in “Information” (p. 79) in the setup menu.
• You may not be able to receive some Internet radio stations.
• The unit uses the vTuner Internet radio station database service. This service may be discontinued without notice.
Playback of Internet radio
Use the MusicCast CONTROLLER app installed on your mobile
device to select an Internet radio station.
• Configure basic settings for the MusicCast CONTROLLER app before selecting
an Internet radio station.
• Refer to the supplied “MusicCast Setup Guide” for details.
Registering favorite Internet radio stations
Assign Internet radio stations to the NET RADIO keys on the remote
control, or save them in the vTuner Bookmarks folder.
1
Select the desired Internet radio station.
2
Press and hold one of the NET RADIO keys (1–3) for
at least 3 seconds.
❑ Tuning into assigned Internet radio stations
1
Press the NET RADIO key (1–3) to which the desired
Internet radio station has been assigned.
“NET RADIO” is shown in the front panel display, and
streaming begins.
Listening to Internet radio
Assigning a station to a NET RADIO key
NET RADIO
1
-
3
NETWORKS ➤ Listening to Internet radio En 63
You can also register your favorite Internet radio stations on the vTuner website.
1
Select any of Internet radio stations on the unit.
This operation is necessary to register the radio station for the first time.
2
Check the vTuner ID of the unit.
You can find the vTuner ID in “Information” (p. 79) in the setup menu.
3
Access the vTuner website (http://yradio.vtuner.com/) with the web
browser on your PC and enter the vTuner ID.
• To use this feature, you need to create your personal account. Create your account using your e-mail
address.
4
Register your favorite radio stations.
Click the “Add” icon ( ) next to the station name.
• To remove the station from the “Bookmarks” folder, select “Bookmarks” in the Home screen, and then
click the “Remove” icon ( ) next to the station name.
Registering the station on the vTuner website
You can switch the language.
Enter the vTuner ID in this area.
NETWORKS ➤ Playing back music with AirPlay En 64
The AirPlay function allows you to play back iTunes or iPod music on the unit via
network.
• This section describes “iPod touch”, “iPhone” and “iPad” as the “iPod”. “iPod” refers to “iPod touch”,
“iPhone” and “iPad”, unless otherwise specified.
• To use this function, the unit and your PC or iPod must be connected to the same router (p. 51). You can
check whether the network parameters (such as the IP address) are properly assigned to the unit in
“Information” (p. 79) in the setup menu.
• When using a multiple SSID router, access to the unit might be restricted depending on the SSID to
connect. Connect the unit and iPod to the same SSID.
• The AirPlay function can be used with an iPhone, iPad, or iPod touch running iOS 4.3.3 or later, a Mac
running OS X version 10.8 “Mountain Lion” or later, or a Windows computer with iTunes 10.2.2 or later
installed.
Playback of iTunes/iPod music contents
Follow the procedure below to play back iTunes/iPod music contents on the unit.
1
Turn on the unit, and start iTunes on the PC or display the playback
screen on the iPod.
If the iTunes/iPod recognizes the unit, the AirPlay icon ( ) appears.
• If the icon does not appear, check whether the unit and PC/iPod are connected to the router properly.
2
On the iTunes/iPod, click (tap) the AirPlay icon and select the unit
(network name of the unit) as the audio output device.
Playing back music with AirPlay
The unit
iTunes
iPod
Router
(wired or
wireless)
(wired or
wireless)
iTunes (example) iPod iOS7/iOS8 (example) iPod iOS6 (example)
YSP-5600 XXXX
YSP-5600 XXXX
iTunes (example) iPod (example)
Network name of the unit
NETWORKS ➤ Playing back music with AirPlay En 65
3
Select a song and start playback.
To operate playback, use the Music app on the iPod or iTunes on the PC.
“AirPlay” is shown in the front panel display, and playback begins.
• You can turn on the unit automatically when starting playback on iTunes or iPod by setting “Network
Standby” (p. 82) in the setup menu to “On”.
• You can edit the network name (the unit’s name on the network) displayed on iTunes/iPod in “Network
Name” (p. 82) in the setup menu.
• You can adjust the unit’s volume from the iTunes/iPod during playback.
Caution
• When you use iTunes/iPod controls to adjust volume, the volume may be unexpectedly loud. This could
result in damage to the unit or speakers. If the volume suddenly increases during playback, stop
playback on the iTunes/iPod immediately.
NETWORKS ➤ Playing back music stored on mobile devices En 66
Use this function to play music stored on your mobile device over a network.
• To use this function, the unit and your PC or mobile device must be connected to the same router (p. 51).
You can check whether the network parameters (such as the IP address) are properly assigned to the unit
in “Information” (p. 79) in the setup menu.
• When using a multiple SSID router, access to the unit might be restricted depending on the SSID to
connect. Connect the unit and mobile device to the same SSID.
Using a mobile device to play songs
Use the MusicCast CONTROLLER app installed on your mobile device to operate
playback.
• Configure basic settings for the MusicCast CONTROLLER app before playing music.
• Refer to the supplied “MusicCast Setup Guide” for details.
Playing back music stored on mobile devices
The unit
Mobile device
Router
(wired or wireless)
Caution
• When you use mobile device controls to adjust volume, the volume may be unexpectedly loud. This
could result in damage to the unit or speakers. If the volume suddenly increases during playback, stop
playback on the mobile device immediately.
SETTINGS ➤ Setup menu En 67
SETTINGS
A variety of settings for this unit can be specified and adjusted from the setup menu. Among the options available are the sound beam output
method for optimal surround sound effects, channel volume control, and HDMI settings.
The setup menu is displayed on, and operated from, the TV screen (it cannot be displayed in the front panel display). See “Displaying the
menu screen on the TV” (p. 28) for instructions on displaying the setup menu on the TV.
Setting the setup menu
1
Press the SETUP ( ) key.
The menu changes as follows each time the SETUP ( )
key is pressed.
• Hold down the SETUP ( ) key to display “OSD Language” directly on the
screen (p. 29, 78).
• If an update for the unit’s firmware is available, an envelope icon ( ) will be
displayed in the setup menu (p. 88).
2
Press the S/T key to select a menu and then press
the ENTER key or X key.
Repeat these steps to display the desired menu.
Press the W key or RETURN ( ) key to return to the
previous menu.
3
Press the S/T key to change the setting value of
each menu.
4
Press the SETUP ( ) key again to exit the setup
menu.
Setup menu
T
Configure “Beam”, “Sound”, “HDMI”, “Display”, and
“Information”.
T
Configure “Network” and “Bluetooth”.
T
Exit the setup menu.
Setup Menu
Beam
Sound
HDMI
Display
Information
IntelliBeam
Horizontal Angle
Vertical Angle
Beam Travel Length
Focal Length
Image Location
Channel Out
Subwoofer
Setup Menu
Beam
Sound
HDMI
Display
Information
IntelliBeam
Horizontal Angle
Vertical Angle
Beam Travel Length
Focal Length
Image Location
Channel Out
Subwoofer
///
ENTER
SETUP ( )
RETURN ( )
SETTINGS ➤ Setup menu En 68
Setup menu list
Menu Settings Function Page
Beam
IntelliBeam
Beam+Sound optimize Optimizes the sound beam and sound settings automatically. 33
Beam optimize only Optimizes the sound beam settings automatically. 33
Sound optimize only Optimizes the sound settings automatically. 33
Horizontal Angle Front L, Front R, Center, Surround L, Surround R Adjust horizontal sound beam angle. 70
Vertical Angle
Front L, Front R, Center, Surround L, Surround R,
Height L, Height R
Adjust vertical sound beam angle. 70
Beam Travel Length
Front L, Front R, Center, Surround L, Surround R,
Height L, Height R
Adjust sound beam travel length. 71
Focal Length
Front L, Front R, Center, Surround L, Surround R,
Height L, Height R
Adjust sound beam focal length. 71
Image Location Adjustment, Left, Right Adjusts the sound position of the front right and left channels. 72
Channel Out
Front Specify the output method for the front channels. 73
Surround Back Specify whether or not there are surround back channels. 73
My Surround Enable/disable the My Surround function. 74
Subwoofer
Bass Out Specify whether or not the subwoofer is used and how it is connected. 74
Cross Over Specify the upper limit of audio frequencies output from the subwoofer. 74
Distance Specify the distance from the subwoofer to the listening position. 74
Pairing Manually pair the unit with the wireless subwoofer kit. 74
Sound
Channel Level
Front L, Front R, Center, Surround L, Surround R,
Height L, Height R, Subwoofer
Adjusts the volume of each channel. 75
Adaptive DRC Choose whether or not dynamic range is adjusted based on this unit’s volume level. 75
Dynamic Range Specify dynamic range. 76
DTS Neural:X, Dialog Control Specify the DTS decoder. 76
HDMI
HDMI Control Turn HDMI control on or off. 77
HDMI Audio Out Choose whether HDMI audio input is played via this unit or the TV. 77
TV Input
Select the TV input jack from TV (digital optical) jack, AUX1 (analog) jack, and
AUX2 (digital coaxial) jack.
77
SETTINGS ➤ Setup menu En 69
Display
Dimmer Adjust the brightness of the front panel display and indicators. 78
OSD Language Changes the language used for menus displayed on the TV screen. 78
Distance Unit Specify units used for length and distance in menus. 78
Information
Audio Display audio input signal information. 79
Video Display video input signal information. 79
System Display this unit’s firmware version. 79
Network
Information Display the unit’s network information. 80
Network Connection Select the network connection method. 80
IP Address
DHCP, IP Address, Subnet Mask, Default
Gateway, DNS Server (P), DNS Server (S)
Configure the network parameters (such as IP address). 81
MAC Address Filter Filter, MAC Address 1–10 Set the MAC address filter to limit access to the unit from other network devices. 81
Network Standby Enable/disable the function that turns on the unit from other network devices. 82
Network Name
Edit the network name (the unit’s name on the network) displayed on other network
devices.
82
Network Update Perform Update Update the firmware via the network. 82
Bluetooth
Bluetooth Enable/disable the Bluetooth functions. 83
Transmission
Turn the function that transmits audio to a Bluetooth device, such as Bluetooth
speakers, on or off.
83
Device Search
Search for the Bluetooth device, such as Bluetooth speakers, to which audio will be
transmitted.
83
MAC Address Display the MAC address for the Bluetooth connection. 83
Menu Settings Function Page
SETTINGS ➤ Setup menu En 70
Beam
When “AUTO SETUP” in the “IntelliBeam” menu (p. 31) is used, recommended beam settings are automatically applied by this unit. However, “Horizontal Angle”, “Vertical Angle”,
“Beam Travel Length”, “Focal Length” (except “Center”), and “Image Location” settings can later be fine-tuned.
The output method for each channel can also be specified in “Beam” menu.
• When manually adjusting sound beams for the front channels, set “Front” for “Channel Out” to “Beam”. Adjustment is not possible if “Front” is set to “Stereo”.
Adjust the horizontal angle of sound beams for each channel using test tones.
Adjust toward L (left) to move the direction of the output to the left and adjust toward R
(right) to move it to the right.
Settings
Front L, Front R, Center, Surround L, Surround R
Adjustable range
L90° to R90°
Adjust the vertical angle of sound beams for each channel using test tones.
Adjust upward to move output direction up, and adjust downward to move output
direction down.
Horizontal Angle
Setup Menu
➜
Beam
➜
Horizontal Angle
Beam angle
Angle to
left
Angle to
right
Left
W key:
Increase angle.
X key:
Decrease angle.
Right
X key:
Increase angle.
W key:
Decrease angle.
Vertical Angle
Setup Menu
➜
Beam
➜
Vertical Angle
S Upward
T Downward
Settings
Front L, Front R, Center, Surround L,
Surround R
Adjustable range
-45° to +45° (default: 0° (horizontal))
S Upward T Downward
Settings
Height L, Height R
Adjustable range
+30° to +90°
SETTINGS ➤ Setup menu En 71
Specify the distance that sound beams travel for each channel. The distance starts at
this unit, ends at the listening position, and includes refraction off a wall and ceiling.
The audio delay is adjusted and sound from each channel arrives at the listening
position simultaneously.
Settings
Front L, Front R, Center, Surround L, Surround R, Height L, Height R
Adjustable range
0.3 m to 24.0 m (1.0 ft to 80.0 ft)
• Configure this setting only when you have adjusted “Horizontal Angle” or “Vertical Angle”.
Expand the optimal listening area (sweet spot).
The illustration below shows how output from all channels is once concentrated in a
focal point and then expanded from that point. Apply negative (-) values to broaden the
sweet spot, or positive (+) values to narrow the sweet spot.
Settings
Front L, Front R, Surround L, Surround R, Height L, Height R
Adjustable range
-1.0 m to +13.0 m (-3.5 ft to +43.5 ft)
Setting
Center
Adjustable range
-1.0 m to +13.0 m (default: -0.5 m) (-3.5 ft to +43.5 ft (default: -1.5 ft))
Beam Travel Length
Setup Menu
➜
Beam
➜
Beam Travel Length
The length of each
arrow indicates the
beam travel length.
Focal Length
Setup Menu
➜
Beam
➜
Focal Length
Focal
length
Focal
point
Sweet
spot
SETTINGS ➤ Setup menu En 72
We recommend using the default setting (-0.5 m or -1.5 ft) for “Center”.
• “AUTO SETUP” (p. 31) automatically enables a range for optimal listening (sweet spot) that is broader than
the width of this unit.
If sound from the left and right channels is unnatural, first adjust the volume of each
channel (p. 43, 75).
If this does not resolve the problem, adjust left- and right-channel image location.
Use to adjust the direction from which the front left and right channel sound is heard so
that each sound can be heard closer to the center channel.
❑ Adjustment
Settings
❑ Left
The higher the percentage, the louder the output from the center channel.
Once “Adjustment” has been set to “On”, this setting can be selected.
Adjustable range
0% (default) to 95%
0
Example
Center channel
With negative focal
lengths
Left front channel
With positive focal
lengths
Image Location
Setup Menu
➜
Beam
➜
Image Location
Off (default) No adjustments are made.
On Choose “Left” or “Right” to adjust the direction from which sound is heard.
Sound from the left front
channel is unnatural
With the left front channel
adjusted
SETTINGS ➤ Setup menu En 73
❑ Right
The higher the percentage, the louder the output from the center channel.
Once “Adjustment” has been set to “On”, this setting can be selected.
Adjustable range
0% (default) to 95%
Specify the output method for each channel.
❑ Front
Specify whether sound beams or normal sounds are output from the front channels.
Settings
• This setting is not available when “My Surround” is selected.
• When manually adjusting sound beams for the front channels, set “Front” to “Beam”. Adjustment is not
possible if “Front” is set to “Stereo”.
❑ Surround Back
Specify whether or not surround back channels are present.
Settings
Channel Out
Setup Menu
➜
Beam
➜
Channel Out
Sound from the right front
channel is unnatural
With the right front channel
adjusted
To output sound beams To output stereo sounds
Beam
Sound beams are output from the left front, right front, and center channels.
This setting is effective for creating sound fields greater than the dimensions of
the actual listening room for playback of movies and the like.
Stereo
No sound beams are output from the left front, right front, and center channels.
Front channel audio comes from the direction of the screen. Therefore, this
setting is effective for enjoying music content such as live music videos.
None
Sounds are played back without using surround back channels. Left and right
surround channel audio is played back using sound beams that come from
behind the listening position.
Yes
Sounds are played back using surround back channels. Left and right surround
back channel audio is played back using sound beams that come from behind
the listening position. Left and right surround channel audio is output using both
sound beams that come from the front channels and from behind the listening
position. This allows sounds to be heard from the sides of the listening position
as well.
Auto (default)
Automatically select whether or not surround back channels are used based on
the number of channels used for playback of the selected input source.
FL FR
SL SR
SL SR
SBL SBR
C
FL FR
C
None Yes
FL: Front L
FR: Front R
C: Center
SL: Surround L
SR: Surround R
SBL: Surround back L
SBR: Surround back R
SETTINGS ➤ Setup menu En 74
❑ My Surround
Specify whether or not “My Surround” is enabled to reproduce a sense of surround
sound even in a room not suitable for surround sound playback using sound beams.
Settings
• To use “My Surround”, establish the listening position directly in front of the unit for a greater sense of
surround sound.
• When “My Surround” is set to “On”, CINEMA DSP is disabled.
• When “My Surround” is set to “On”, Dolby Atmos playback or playback using height channels is not
possible.
Specify whether or not the subwoofer will be used, how it will be connected, and its
distance to the listening position.
❑ Bass Out
Specify whether or not the subwoofer will be used and how it is connected.
Settings
❑ Cross Over
Specify the upper limit of audio frequencies output from the subwoofer (the lower limit
of audio frequencies output from the unit).
Settings
80 Hz, 100 Hz (default), 120 Hz
❑ Distance
Specify the distance from the subwoofer to the listening position.
Adjustable range
0.3 m (1.0 ft) to 15.0 m (50.0 ft) (default: 2.5 m (8.5 ft))
❑ Pairing
Manually pair the unit with the wireless subwoofer kit.
After “Pairing” is selected, press the PAIRING button on the wireless subwoofer kit for
three seconds.
• “Pairing” can be selected when “Bass Out” is set to “Front/Wireless”.
Off (default) My Surround is disabled.
On
“My Surround” is enabled. Enjoy playing audio with a good sense of surround
sound even in an environment where surround sound playback using sound
beams does not provide sufficient surround sound effects.
Press the 3D SURROUND key or the SURROUND key on the remote control for
playback using the My Surround function.
Subwoofer
Setup Menu
➜
Beam
➜
Subwoofer
Front/Wireless
(default)
Select when the subwoofer will not be used, or when the wireless subwoofer kit
will be used.
Wired Select when the subwoofer is connected to the unit with a cable.
SETTINGS ➤ Setup menu En 75
Sound
Adjust the volume of each channel to balance output levels. Use test sounds output
from each channel to adjust volume for optimal balance.
Settings
Front L, Front R, Center, Surround L, Surround R, Height L, Height R, Subwoofer
Adjustable range
-20 to +20
• When “My Surround” of “Channel Out” is set to “On” the following items can be configured (p. 74).
–Center
– Surround L/R
– Subwoofer
Adjust this unit’s volume and dynamic range for optimal balance. When “On” is
selected, dynamic range is adjusted as follows for optimal listening at low volumes,
such as might be used at night.
When the volume level is low:
Narrow the dynamic range. Loud sound is played back softer, and soft sound which is
hard to be listened to is played back louder.
When the volume level is high:
Widen the dynamic range. For both soft and loud sounds, source sound is played back
without adjusting volume.
Settings
• When set to “On”, “Dynamic Range” is automatically set to “Max”.
Channel Level
Setup Menu
➜
Sound
➜
Channel Level
Adaptive DRC
Setup Menu
➜
Sound
➜
Adaptive DRC
Off The dynamic range is not adjusted automatically.
On (default) Adjust the dynamic range automatically.
On
Output level
Output level
Off
Off
Input level Input level
Volume: low Volume: high
On
SETTINGS ➤ Setup menu En 76
Adjust this unit’s dynamic range (difference between maximum and minimum volumes).
Settings
• “Adaptive DRC” is automatically set to “Off” when the settings other than “Max” is selected.
Configure the DTS decoder for use with input of DTS audio signals.
❑ Neural:X
Specify whether or not Neural:X is used to generate channels not present in input
sources.
Settings
• Neural:X is the DTS:X surround sound decoder.
❑ Dialog Control
Increase the volume of dialog to make listening easier.
Adjustable range
0 (default) to 6 (dB)
• This setting is effective only for playback of DTS:X input sources that support dialog control.
Dynamic Range
Setup Menu
➜
Sound
➜
Dynamic Range
Min/Auto
Min: Sets dynamic range at a level that supports comfortable listening at low
volumes.
Auto: Sets dynamic range in accordance with information received from input
signal.
Standard The dynamic range recommended for regular home use.
Max (default) Outputs sound without adjusting the dynamic range of the input signals.
DTS
Setup Menu
➜
Sound
➜
DTS
Disable Neural:X will not be used.
Enable (default) Neural:X will be used.
“Neural:X” and “Dialog Control” may be provided with a firmware update.
See our website for the latest information.
The following settings are available for the DTS decoder before “Neural:X”
and “Dialog Control” are provided with firmware update.
Configure the DTS Neo:6 decoder for use when DTS audio signals are input.
Settings
• The DTS Neo:6 decoder is disabled with stereo playback and target playback.
Neo:6 Cinema
(default)
Use the DTS Neo:6 decoder suitable for movies.
Neo:6 Music Use the DTS Neo:6 decoder suitable for music.
SETTINGS ➤ Setup menu En 77
HDMI
Use to configure the settings related to HDMI signals and the HDMI control function.
Turn HDMI control (p. 35) on or off.
Settings
This setting can be configured only when “HDMI Control” is set to “Off”.
Use to select a device to play back HDMI audio signals.
Settings
• When “HDMI Control” is set to “On”, select the audio output device based on the settings configured for the
TV connected to this unit.
• HDMI video signals input to one of the HDMI IN jacks of this unit are always output from the HDMI OUT
(ARC) jack of this unit.
If your TV is not ARC compatible (or if the ARC feature has been disabled), TV audio is
input via the TV (digital optical) jack (default). This unit’s input source can be changed
to the AUX2 (digital coaxial) jack or AUX1 (analog) jack.
Settings
Optical [TV] (default), Analog [AUX1], Coaxial [AUX2]
• If this unit’s input source is switched to “Coaxial [AUX2]”:
Audio is input from the device (TV) connected to the AUX2 (digital coaxial) jack on this unit when the TV
key is pressed. Audio is input from the device connected to the TV (digital optical) jack on this unit when the
AUX2 key is pressed.
• If this unit’s input source is switched to “Analog [AUX1]”:
Audio is input from the device (TV) connected to the AUX1 (analog) jack on this unit when the TV key is
pressed. Audio is input from the device connected to the TV (digital optical) jack on this unit when the AUX1
key is pressed.
HDMI Control
Setup Menu
➜
HDMI
➜
HDMI Control
Off (default)
Disable the control function. The standby power consumption of this unit
decreases.
On Enable the control function.
HDMI Audio Out
Setup Menu
➜
HDMI
➜
HDMI Audio Out
AMP (default) Play back the input sound signal.
TV Plays audio content from the TV connected to the HDMI OUT (ARC) jack.
TV Input
Setup Menu
➜
HDMI
➜
TV Input
SETTINGS ➤ Setup menu En 78
Display
Adjust the brightness of the front panel display and indicators. The smaller the value,
the dimmer the display and indicators.
Settings
-4 (darkest) to 0 (brightest) (default)
• When the STATUS indicator glows red, the display is at maximum brightness regardless of this setting.
• When the Eco function is activated, this function cannot be configured (p. 44).
Use to select the language used for menus displayed on the TV screen.
Settings
• Hold down the SETUP ( ) key to display “OSD Language” directly on the TV screen.
• The settings may be changed automatically when using the TV which supports the HDMI control function.
• Display language can only be selected for menus displayed on the TV screen. Information in the front panel
display is displayed in English.
Use to change the display unit of measurement.
Settings
Meters (default setting other than U.S.A. and Canada models), Feet (default setting for U.S.A. and
Canada models)
• If the unit used with measurement displays is changed from “Meters” to “Feet”, or vice versa, configure
settings again to reflect the change in unit. The change will not be reflected with current settings.
Dimmer
Setup Menu
➜
Display
➜
Dimmer
OSD Language
Setup Menu
➜
Display
➜
OSD Language
Menus are displayed in Japanese.
ENGLISH
(default)
Menus are displayed in English.
DEUTSCH Menus are displayed in German.
FRANÇAIS Menus are displayed in French.
ESPAÑOL Menus are displayed in Spanish.
ITALIANO Menus are displayed in Italian.
NEDERLANDS Menus are displayed in Dutch.
РУССКИЙ Menus are displayed in Russian.
SVENSKA Menus are displayed in Swedish.
TÜRK
Menus are displayed in Turkish.
Distance Unit
Setup Menu
➜
Display
➜
Distance Unit
SETTINGS ➤ Setup menu En 79
Information
Display information for the audio and video signal input to this unit.
The following information on the current audio input signal is displayed.
• The audio bit rate may not be displayed for some input signals.
The following information on the current video input signal is displayed.
Display the version of firmware currently installed on this unit.
Audio
Setup Menu
➜
Information
➜
Audio
Format Digital audio format
Number of channels
The number of channels contained within the input signal—front/
surround/low field effects (LFE). Example: “3/2/0.1” means signal contains
3 front channels, 2 surround channels, and LFE.
If the signal contains channels other than front, surround, and LFE, the
total number of channels may be displayed. Example: “7.1.2ch” (the last
number 2 indicates the height channels)
Sampling frequency The sampling frequency of the digital input signal
Bit rate The per-second bit rate of the input signal
Video
Setup Menu
➜
Information
➜
Video
Type HDMI or DVI
Resolution Video signal resolution
System
Setup Menu
➜
Information
➜
System
SETTINGS ➤ Setup menu En 80
Network
Configures the network settings.
Display the network information on the unit.
• The options displayed vary according to the type of network connection (Wired/Wireless (Wi-Fi)/Wireless
Direct).
Select the network connection method.
Settings
Information
Setup Menu
➜
Network
➜
Information
Status The connection status of the NETWORK jack
Connection Connection method
MC Network The connection status of MusicCast Network
SSID The access point to which the unit is connected
Security The encryption method for your network
MAC Address MAC address (Ethernet/Wi-Fi)
IP Address IP address
Subnet Mask Subnet mask
Default Gateway The IP address of the default gateway
DNS Server (P) The IP address of the primary DNS server
DNS Server (S) The IP address of the secondary DNS server
vTuner ID The ID of the Internet radio (vTuner)
Network Connection
Setup Menu
➜
Network
➜
Network Connection
Wired
Select this option when connecting the unit to a network with a network
cable (not supplied).
Wireless (Wi-Fi)
Select this option when connecting the unit to a network via the wireless
router (access point).
Wireless Direct Select this option when connecting a mobile device to the unit directly.
SETTINGS ➤ Setup menu En 81
Configure the network parameters (such as IP address).
❑ DHCP
Select whether to use a DHCP server.
Settings
Manual network settings
1
Set “DHCP” to “Off”.
2
Use the S/T keys to select a parameter type.
3
Use the W/X keys to move the edit position and the S/T keys to
select a value.
4
Press the ENTER key.
The MAC address filter limits network devices that can be used to operate the unit.
When operating the unit via an app on a mobile device, specify the MAC address of the
device.
• Operation of the AirPlay function (p. 64) or DLNA-compatible device (p. 61) is not limited by this setting.
❑ Filter
Enable/disable the MAC address filter.
Settings
❑ MAC Address 1–10
Specify the MAC addresses (up to 10) of the network devices that will operate the unit
when “Filter” is set to “On”.
1
Use the S/T keys to select an MAC address number (1 to 10).
2
Use the W/X keys to move the edit position and the S/T keys to
select a value.
3
Press the ENTER key.
IP Address
Setup Menu
➜
Network
➜
IP Address
Off
The DHCP server is not used. Configure the network parameters
manually. For details, see “Manual network settings”.
On (default)
The DHCP server is used to automatically obtain the unit’s network
parameters (such as IP address).
IP Address Specify an IP address.
Subnet Mask Specify a subnet mask.
Default Gateway Specify the IP address of the default gateway.
DNS Server (P) Specify the IP address of the primary DNS server.
DNS Server (S) Specify the IP address of the secondary DNS server.
MAC Address Filter
Setup Menu
➜
Network
➜
MAC Address Filter
Off (default) Disable the MAC address filter.
On
Enable the MAC address filter. In “MAC Address 1–10”, specify the MAC
addresses of the network devices that will operate the unit.
SETTINGS ➤ Setup menu En 82
Turn the function that controls the unit’s power (Network Standby) when a network
device or Bluetooth device is operated on or off.
Settings
• The unit consumes more power when “Network Standby” is set to “On” than when it is set to “Off”.
Edit the name displayed for this device (the unit’s name on the network) on other
network devices. A name up to 15 characters in length may be specified.
1
Use the W/X keys to move the edit position and the S/T keys to
select a character.
• The following alphanumeric characters and symbols may be used.
()[]{}<>*!?#%&.,:;_|/\$~^'"`0–9@+-=A–Za–z
2
Press the RETURN ( ) key.
Update the firmware via the network.
Perform Update
This option is available after firmware has been updated. For details, see “Updating the
unit’s firmware” (p. 88).
Network Standby
Setup Menu
➜
Network
➜
Network Standby
Off Disable the network standby function.
On (default)
Enable the network
standby function.
The unit will turn on when the dedicated MusicCast
CONTROLLER or HOME THEATER CONTROLLER (WLAN)
app installed on your mobile device is used to initiate
playback while the unit is off.
The unit will turn on and off in accordance with the
following Bluetooth device operations.
Coordinated power on
When a Bluetooth device is connected to this unit while it is
off, this unit turns on and the input source switches to
BLUETOOTH.
Coordinated power off
When a Bluetooth device is disconnected from this unit
while it is on, this unit turns off.
(Only when BLUETOOTH is selected as the input source.)
Network Name
Setup Menu
➜
Network
➜
Network Name
Network Update
Setup Menu
➜
Network
➜
Network Update
Network Name
YSP-5600 1B08FA
[RETURN]:Back
SETTINGS ➤ Setup menu En 83
Bluetooth
Configures the Bluetooth settings.
Enables/disables the Bluetooth function.
Settings
Transmit audio from the unit to Bluetooth speakers or headphones.
Settings
Select the Bluetooth speakers or headphones to which audio will be transmitted, and
connect the unit to the speakers or headphones wirelessly.
Display the MAC address for the Bluetooth connection.
Bluetooth
Setup Menu
➜
Bluetooth
➜
Bluetooth
Off Disable the Bluetooth function.
On (default) Enable the Bluetooth function.
Transmission
Setup Menu
➜
Bluetooth
➜
Transmission
Off (default) Audio can not be transmitted.
On
Audio input to the unit can be transmitted to Bluetooth speakers or
headphones.
Device Search
Setup Menu
➜
Bluetooth
➜
Device Search
MAC Address
Setup Menu
➜
Bluetooth
➜
MAC Address
SETTINGS ➤ Settings each input source (Option menu) En 84
Configure the functions related to the input source currently playing back content.
The option menu is displayed on, and operated from, the TV screen. See “Displaying the menu screen on the TV” (p. 28) for instructions on
displaying the option menu on the TV.
Setting the option menu
1
Press the input selector key for the input source to
be configured.
2
Press the OPTION ( ) key.
3
Select the items by pressing the S/T key, then
press the ENTER key or X key.
4
Change setting value by pressing the S/T key.
5
Press the OPTION ( ) key to exit the option menu.
• The configurable items vary depending on the input source selected.
Settings each input source (Option menu)
Option
Treble
Bass
Volume Trim
Audio Delay
Audio Assign
0
Option
Treble
Bass
Volume Trim
Audio Delay
Audio Assign
0
Option
Treble
Bass
Volume Trim
Audio Delay
Audio Assign
-
5
///
ENTER
OPTION ( )
Input selector
keys
SETTINGS ➤ Settings each input source (Option menu) En 85
Option menu list
Adjust the output level of high (treble) and low (bass) tones.
Adjustable range
-12 to +12 (default: 0)
Adjust the input level for each jack to compensate for variations in volume.
Adjustable range
-12 to +12 (default: 0)
TV images sometimes lag behind the sound. You can use this function to delay the
sound output to synchronize it with the video image.
Adjustable range
HDMI1– 4: AUTO (default), 0 ms to 500 ms, 5 ms increments
TV, OPTICAL, AUX1– 2: 0 ms (default) to 500 ms, 5 ms increments
When “AUTO” is selected, output timing is automatically adjusted. This setting is only
available when the TV connected via HDMI cable supports the audio delay automatic
adjustment feature.
When HDMI1– 4 is the selected input source, sound can be input from the OPTICAL
jack rather than the HDMI IN jack.
Use this function to listen to sound from a different playback device while watching
video of the BD/DVD player.
Settings
HDMI (default), OPTICAL
Menu Description Input
Treble
Adjust the output level of high (treble)
tones.
HDMI1– 4, TV, OPTICAL, AUX1– 2,
Bluetooth, NET (such as an internet
radio station)
Bass
Adjust the output level of low (bass)
tones.
HDMI1– 4, TV, OPTICAL, AUX1– 2,
Bluetooth, NET (such as an internet
radio station)
Volume Trim
Adjust the input level for each jack to
compensate for variations in volume.
HDMI1– 4, TV, OPTICAL, AUX1– 2,
Bluetooth, NET (such as an internet
radio station)
Audio Delay
Adjust deviations in timing between
audio and video playback.
HDMI1– 4, TV, OPTICAL, AUX1– 2
Audio Assign
When an HDMI device is selected as
the input source, audio from a different
input source is assigned to HDMI
audio.
HDMI1– 4
Adjusting tones (Treble, Bass)
Adjusting input level of each jack (Volume Trim)
Audio delay control (Audio Delay)
Assigning HDMI audio to a different input jack
(Audio Assign)
SETTINGS ➤ Advanced setup En 86
The advanced setup enables more precise configuring of this unit’s function. For example, maximum volume can be specified and the INPUT
key on the top panel can be disabled.
Setting the advanced setup
1
Press the z key to turn off this unit.
2
While holding down the INPUT key on the top panel,
press the z key on the remote control to turn on the
power.
“ADVANCED” appears in the front panel display.
• The advanced setup menu is not displayed on the TV screen.
3
Release the INPUT key on the top panel.
4
Use the S/T key to display the desired menu in the
front panel display and then press the X key or
ENTER
key.
• To return to the previous menu, press the W or RETURN ( ) key.
5
Use the S/T key to change setting.
6
Press the z key to turn off this unit.
The new setting is reflected when you turn on the unit by
pressing the z key.
Advanced setup
INTELLIBEAM MIC
CONNECT
INPUT
ADVANCED
z
///
ENTER
RETURN ( )
SETTINGS ➤ Advanced setup En 87
Advanced setup list
• Initializing this unit also initializes measurement results with IntelliBeam and settings stored in system memory. Perform “AUTO SETUP” from the “IntelliBeam” menu again (p. 30).
Menu Settings/Adjustable range Description
TURN ON VOLUME OFF (Not set) (default), 1 to 70
Set the initial volume level when the power of this unit is turned on.
When set to “OFF”, volume level is the same as when this unit is turned off.
MAX VOLUME 1 to 99, MAX (Maximum) (default) Set the maximum volume level so that this unit will not output sound beyond the limited volume level.
INPUT LOCK
ON (INPUT key operation is disabled)
OFF (INPUT key operation is enabled) (default)
Select whether or not to enable the INPUT key on the unit.
PANEL LOCK
ON (Key operation on the unit is disabled)
OFF (Key operation on the unit is enabled) (default)
Select whether or not to enable key operations on the unit (except the advanced setup operations).
IR INPUT POWER
ON (Enables power-on)
OFF (Disables power-on) (default)
Select whether or not to automatically turn on this unit by pressing an input selector key on the remote
control when the unit is turned off.
AC ON STANDBY
ON (Enters standby mode) (default)
OFF (Restores the state before power was lost)
Set this unit’s power to off when the AC power is recovered after the power to this unit was lost temporally
(disconnect the AC power plug from the wall outlet, power outage, etc.).
MEMORY PROTECT
ON (Protect is performed)
OFF (Protect is not performed) (default)
Protect settings stored in system memory, and Internet radio stations registered with the unit.
YRB FL
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the front left channel. Refer to page 100 for details of YRB-100.
YRB FR
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the front right channel. Refer to page 100 for details of
YRB-100.
YRB SL
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the surround left channel. Refer to page 100 for details of
YRB-100.
YRB SR
YES (The reflection board is used)
NO (The reflection board is not used) (default)
Use the YRB-100 sound reflection board for the surround right channel. Refer to page 100 for details of
YRB-100.
AUTO POWER STANDBY
ON (This unit turns off automatically) (default setting for U.K.,
Europe and Russia models)
OFF (This unit does not turn off automatically) (default setting
other than U.K., Europe and Russia models)
When set to “ON”, this unit turns off automatically in any of the following situations:
• Audio is coming from the selected input source, but no operations have been performed for 8 hours or
more.
• HDMI1– 4, Bluetooth or NET is selected as the input source, but no audio has been input to the unit or no
operations have been performed with the unit for more than 20 minutes.
NOTICE OF NEW FW
ON (Notify) (default)
OFF (Do not notify)
Notifications will not be displayed on the TV screen when updates for the unit’s firmware are provided via
the network.
FW UPDATE
01.02 (The firmware version is displayed)
Start OK? (Firmware is updated)
Confirm firmware version/update firmware.
INITIALIZE
INFO (Initialize all settings not related to the network)
NET INFO (Initialize network related settings)*
CANCEL (Do not initialize) (default)
Reset the parameters of this unit to the factory presets. When the unit freezed, the problem may solve by
restoring to their default values.
* The following configurations will be restored if “INFO” is selected.
• Network Standby (p. 82)
• Bluetooth (p. 46)
SETTINGS ➤ Updating the unit’s firmware En 88
New firmware that provides additional features or product
improvements will be released as needed. If the unit is connected
to the Internet, you can download the firmware via the network and
update it.
When the unit is turned on for the first time after a new version of the
unit’s firmware has been released, a message indicating that a
firmware update is available will be displayed on the TV screen,
and an envelope icon ( ) will be displayed in the setup menu
(p. 67)
The unit’s firmware can be updated as follows.
• Update firmware from “Network Update” in the setup menu.
• Update firmware by connecting a USB flash drive to which the
unit’s firmware update has been saved (p. 89).
• Update firmware using the dedicated MusicCast CONTROLLER
app installed on a mobile device. Follow MusicCast
CONTROLLER guides to operate the app and update the
firmware.
Using “Network Update” in the setup menu
to update firmware
1
Press the SETUP ( ) key twice.
The setup menu is displayed on the TV screen.
2
Use the S/T keys to select “Network”, and then
press the ENTER key.
3
Use the S/T keys to select “Network Update”, and
then press the ENTER key.
The following screen is displayed when firmware updates
are available.
• To cancel the operation without updating the firmware, press the SETUP
() key.
Updating the unit’s firmware
Notes
• Do not operate the unit or disconnect the power cable or network cable during
firmware update. Firmware update takes about 20 minutes or more (depending
on your Internet connection speed).
• If the Internet connection speed is slow, or the unit is connected to the wireless
network, network update may not be possible depending on the condition of
the network connection. In this case, update the firmware using the USB flash
drive (p. 89).
• To perform the following procedure, your TV must be connected to the unit via
HDMI.
• For details on update, visit the Yamaha website.
Network Update
Perform Update
/
ENTER
SETUP ( )
SETTINGS ➤ Updating the unit’s firmware En 89
4
Press the ENTER key.
The TV screen goes black and firmware update begins.
Update progress is displayed on the front panel display while firmware is
updated.
5
When “Success!” is shown in the front panel display, press the z
key on the unit’s top panel.
The firmware update is complete.
• If the firmware update fails, use the z key to turn the unit off and then on again, and repeat the procedure
from step 1 again.
• If “XXXXSumError” is displayed, a problem with communications over the network has occurred. Check
communications status, use the z key to turn the unit off and then on again, and then repeat the procedure
from step 1 again.
Updating firmware with connection of a USB flash drive
Download the latest firmware version from the Yamaha website to a USB flash drive,
which can then be used to update the unit’s firmware.
See information provided when updating firmware for details.
1
Save this unit’s firmware to a USB flash drive.
2
Turn off the unit.
3
Connect the USB flash drive to the UPDATE ONLY jack on the unit’s
rear panel.
4
Select “FW UPDATE” in the advanced setup menu, and press the
ENTER key.
5
Use S/T key to select “Start OK?”, and press the ENTER key.
The firmware update begin.
Update progress is displayed on the front panel display while firmware is
updated.
6
When “Success!” is shown in the front panel display, press the z
key on the unit’s top panel.
The firmware update is complete.
FW Update
Success!
The update progress is displayed.
FW Update
Success!
The update progress is displayed.
SETTINGS ➤ Updating the unit’s firmware En 90
• If the firmware update fails, use the z key to turn the unit off and then on again, and repeat the procedure
from step 1 again. If the firmware update fails again, confirm the USB flash drive is correctly connected to
the UPDATE ONLY jack.
• If any of the following messages are displayed, a problem has occurred during the update.
– “Not found”:
The USB flash drive does not contain the firmware data. Use a PC to properly save the firmware data to
the USB flash drive again.
– “XXXXSumError”:
There is a problem with the data stored on the USB flash drive. Use a PC to confirm data on the USB
flash drive.
DTS:X updates
The unit supports update to DTS:X Version 2, scheduled to be released shortly. An
update to DTS:X Version 2 will be provided when the unit’s firmware is updated.
See the information provided with the firmware update for more information on DTS:X
Version 2.
APPENDIX ➤ Troubleshooting En 91
APPENDIX
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off the unit,
disconnect the AC power supply cable, and contact the nearest authorized Yamaha dealer or service center.
General
Troubleshooting
Problem Cause Remedy See page
This unit does not operate
properly.
The internal microcomputer has been frozen by an external electric shock
(such as lightning or excessive static electricity) or by a power supply with
low voltage.
Disconnect the AC power supply cable from the outlet and plug it again in
after 30 seconds. –
This unit fails to turn on when the
z key is pressed, or the unit is
turned off soon after the power
has been turned on.
The AC power supply cable is not firmly connected to the AC wall outlet. Connect the AC power supply cable firmly to the AC wall outlet. 27
The internal microcomputer has been frozen by an external electric shock
(such as lightning or excessive static electricity) or by a power supply with
low voltage.
Disconnect the AC power supply cable from the outlet and plug it again in
after 30 seconds. –
“PANEL LOCK” is set to “ON”. Set to “OFF”. 86
This unit is suddenly turned off. The internal temperature becomes too high and the overheat protection
circuitry has been activated.
Wait for about 1 hour for this unit to cool down, turn it back on after
confirming an adequate amount of ventilation space and not to cover this
unit with a cloth.
12
When the Auto Power Standby function is enabled, this unit turns off
automatically in any of the following situations:
– Audio is coming from the selected input source, but no operations have
been performed for 8 hours or more.
– HDMI1–4, Bluetooth or NET is selected as the input source, but no audio
has been input to the unit or no operations have been performed with the
unit for more than 20 minutes.
Turn on the power of the unit and play back the source again. If the Auto
Power Standby function is not used, set “AUTO POWER STANDBY” to
“OFF”.
87
The network standby function has been activated, terminating the Bluetooth
connection.
Resume the Bluetooth connection using the Bluetooth device, or turn on
this unit and disable the network standby function.
82
APPENDIX ➤ Troubleshooting En 92
No sound. Incorrect input or output cable connections. Connect the cable properly. 23
No appropriate input source has been selected. Select an appropriate input source with the input selector keys. 37
The volume is turned down. Turn up the volume. 37
The sound is muted.
Press the MUTE ( ) or VOL (+/-) key to resume audio output and adjust
the volume level.
37
There is input signal cannot be played back by this unit. Play a source whose signals can be reproduced by this unit. Change the
system settings of the source device.
108
“HDMI Audio Out” is set to “TV”. Set to “AMP”. 77
“HDMI Control” is set to “Off”. When connecting ARC (Audio Return Channel) supported TV and this unit
using an HDMI cable only, set “HDMI Control” to “On”.
77
To use this unit with “HDMI Control” set to “Off”, connect the TV’s audio
output jack to this unit’s TV (digital optical) jack via the optical cable.
22
Sound from an HDMI control-enabled TV is set for output from the TV’s
built-in speakers.
Use the TV’s HDMI settings to set audio output to any option other than the
TV’s built-in speakers.
–
No sound or too small sound from
a specific channel.
The output level of the channel is muted. Raise the output level of the channel. 43, 75
The beam setting is inappropriate. Adjust the beam setting. 30, 70
The source is played in stereo playback mode. Switch to 3D surround/surround playback mode. 38, 39
Surround sound effects are
insubstantial.
When connecting this unit with playback device and TV digitally, the output
setting of the playback device and TV is not valid.
Refer to documentation supplied with your device and check the setting.
–
The playback device is set for constant output from 2 channels (PCM, etc.). Change the playback device’s audio output setting. –
The listening room is not a regular shape, or the unit or listening position is
not at the center of the right and left wall of the listening room.
Relocate the unit or listening position.
13
There is no wall in the path of the sound beam. Place the sound reflection board in the path of the sound beam. 100
When “My Surround” is set to “On”, listening position is not in front of the
unit.
Listen in front of this unit.
74
Sounds from above cannot be
clearly heard.
The angle of sound beams coming from the height channels is not properly
set.
Apply 3D surround sound playback mode, and then set “Height L” and
“Height R” for “Vertical Angle” in the setup menu to positions where audio
can be more clearly heard.
38, 70
A playback mode other than 3D surround sound playback mode is being
used for playback.
Use 3D surround sound playback mode for playback.
38
The ceiling is too high, or there are items protruding from the ceiling. Change the unit’s installation position or the listening position, and then
perform AUTO SETUP again.
30
Problem Cause Remedy See page
APPENDIX ➤ Troubleshooting En 93
No sound is
coming from
the subwoofer.
Wired/Wireless The AC power supply cable of the subwoofer is not firmly connected to the
AC wall outlet.
Connect the AC power supply cable firmly to the AC wall outlet.
–
Wired/Wireless The volume of the subwoofer is low. Increase the volume via the control on the subwoofer. –
Wired/Wireless The subwoofer is turned off. Turn on the subwoofer. –
Wired/Wireless The subwoofer's Auto Standby function (the function that automatically
turns it off) was activated.
Deactivate the subwoofer's Auto Standby function or adjust its operating
sensitivity.
–
Wired The “Bass Out” item under “Subwoofer” is set to “Front/Wireless”. Set it to “Wired”. 74
Wireless Conditions for wireless communications are not good, and the unit and the
wireless subwoofer kit are not connected.
(The indicator on the wireless subwoofer kit flashes green, or glows red.)
Move the wireless subwoofer kit closer to the unit.
If the problem persists, move the wireless subwoofer kit to a location where
its indicator steadily glows green.
–
If there are obstacles such as metal furniture obstructing communications
between the unit and the wireless subwoofer kit, rearrange the furniture or
reposition the wireless subwoofer kit.
–
If there are devices such as microwave ovens or wireless network devices
that emit electromagnetic waves, move the unit and the wireless subwoofer
kit away from these devices.
–
Unplug the power cable of the wireless subwoofer kit from the AC wall
outlet, and then plug it in again.
–
Wireless The unit is not paired with the wireless subwoofer kit.
(The indicator on the wireless subwoofer kit flashes red.)
Move the wireless subwoofer kit closer to the unit to improve conditions for
wireless communications, and pair the two.
If the indicator on the wireless subwoofer kit does not glow green steadily
after pairing, the unit may be malfunctioning. Disconnect the power cable
and contact your nearest Yamaha dealer or service center to request
repairs.
26
Wireless The subwoofer output is set to “Wired”. Set to “Front/Wireless”. 74
The volume of
the subwoofer
is low.
Wired/Wireless The volume of the subwoofer is low. Increase the volume via the control on the subwoofer. –
Increase the volume of the subwoofer with the SUB + key. 37
Wired/Wireless Content from an input source with a limited support for low tones is playing. Play content from an input source with broader support for low tones to see
if volume is still low.
–
Wired/Wireless The unit is in target playback mode. Switch to 3D surround/surround playback mode or stereo playback mode. 38, 39, 41
Sound from
the subwoofer
is intermittent.
Wired/Wireless Cables used to connect the subwoofer to the unit (or the wireless subwoofer
kit) are not connected firmly.
Connect the cables firmly.
25
Wireless Wireless communication conditions are not good, and the unit and the
wireless subwoofer kit are not connected.
(The indicator on the wireless subwoofer kit flashes green, or glows or
flashes red.)
Move the wireless subwoofer kit closer to the unit.
If the problem persists, move the wireless subwoofer kit to a location where
its indicator steadily glows green.
–
If there are obstacles such as metal furniture obstructing communication
between the unit and the wireless subwoofer kit, rearrange the furniture and
the wireless subwoofer kit.
–
If there are devices such as microwave ovens or wireless network devices
that emit electromagnetic waves, move the unit and the wireless subwoofer
kit away from these devices.
–
Problem Cause Remedy See page
APPENDIX ➤ Troubleshooting En 94
Power of the
subwoofer and
this unit is not
turned on and
off at the same
time.
Wired A system control cable used to connect the subwoofer to the unit is not
firmly connected.
Connect the cable firmly.
25
Wireless The subwoofer’s power function setting is not properly configured. (The
power function setting varies depending upon the subwoofer used. See
documentations supplied with the subwoofer for more information.)
Turn on the subwoofer manually. –
If a Yamaha subwoofer has been connected via the SYSTEM CONNECTOR
jack, configure the subwoofer’s setting so that it turns on/off when the unit is
turned on/off.
25
Some subwoofers have a function that turns them on when the transmission
of audio signals by the unit is detected and off when no signal is detected,
and/or a function that allows you to specify the strength of audio signals
detected by the subwoofer. Be sure that these subwoofer functions are
properly configured.
–
The image is not displayed on TV
screen.
The HDMI cable is not securely connected. Connect the HDMI cable properly.
22, 23
Menu screen of this unit is not
displayed.
The input switch of TV is not set correctly. Set the TV’s input source to this unit.
28
A digital or high-frequency
equipment produces noises.
The unit may be placed close to digital equipment or high-frequency
equipment.
Move the equipment away from the unit.
–
The HDMI control function does
not work properly.
“HDMI Control” is set to “Off”. Set “HDMI Control” to “On”. 77
The HDMI control function is disabled on your TV. Refer to documentation supplied with your TV and check the setting. –
The number of the connected HDMI devices exceeds the limit. Disconnect some of the HDMI devices. –
Amplifiers (AV amplifiers, sound bars, etc.) other than the unit are
connected to the TV or a playback device with an HDMI cable.
Connect only this unit to the TV or a playback device for use as an amplifier.
–
Sound beams for the front
channels cannot be adjusted
manually.
“Front” of “Channel Out” is set to “Stereo”. Set to “Beam”.
73
Audio delay control function is
not effective even “Audio Delay”
is set to “AUTO”.
The TV does not support the audio delay auto adjustment feature. Adjust timing of sound output manually from “Audio Delay” in the option
menu. 85
“Disable” appears in the front
panel display after key operation.
The key is unable to function in the current status of the unit.
–
Problem Cause Remedy See page
APPENDIX ➤ Troubleshooting En 95
Bluetooth
Problem Cause Remedy See page
Receiving Unable to
connect the unit
to a Bluetooth
device.
“Bluetooth” is set to “Off”. Set it to “On”. 83
“Transmission” is set to “On”. Set it to “Off”. 83
Bluetooth is not selected as the input source. Select Bluetooth as the input source. 47
Another Bluetooth device is connected. Terminate the current Bluetooth connection, and connect to the device from
which audio should be received.
46, 47
A Bluetooth adaptor, etc. that you want to connect to the unit has a
password other than “0000”.
Use a Bluetooth adaptor, etc. whose password is “0000”.
46
The device does not support A2DP. Connect to a Bluetooth audio device that supports A2DP. 106
As more than 20 devices have been connected, information for the oldest
connection has been deleted.
Connect to the device again. The unit is can connect to up to 20 Bluetooth
devices for receiving and transmitting audio. If a new device is successfully
connected to the unit after 20 other devices have already been connected,
the device with the earliest connection date will have been deleted to make
room for the new device.
46, 47
The unit and device are too far apart. Position the Bluetooth device so that it is less than 10 m from this unit and
connect the device to this unit.
46, 47
There is a device (microwave oven, wireless LAN, etc.) outputs signals in
the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio frequency signals.
–
No sound is
heard or the
sound is
intermittent via
the unit.
The device is not set to send Bluetooth audio signals to the unit. Check that the Bluetooth function of the device is set properly. –
Playback on the device has not been performed. Perform playback on the device. –
The device’s volume is set to minimum. Turn up the volume level on the device. –
The unit and device are too far apart. Move the Bluetooth device so that it is less than 10 m from this unit. 46, 47
There is a device (microwave oven, wireless LAN, etc.) outputs signals in
the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio frequency signal.
–
The Bluetooth connection of the unit with the device is disconnected. Perform Bluetooth connection operations again. 47
APPENDIX ➤ Troubleshooting En 96
Remote control
Transmitting Cannot make the
unit connected
to the Bluetooth
device.
“Bluetooth” is set to “Off”. Set it to “On”. 83
“Transmission” is set to “Off”. Set it to “On”. 83
Another Bluetooth device is connected. Terminate the current Bluetooth connection, and connect to the device to
which audio should be transmitted.
46, 49
The device does not support A2DP. Connect to a Bluetooth audio device that supports A2DP. 106
More than 20 devices are connected and the earliest connecting
information is deleted.
Connect to the device again. The unit is able to connect up to 20 Bluetooth
devices for receiving and transmitting audio. If a new device is successfully
connected to the unit after 20 other devices have already been connected,
the device with the earliest connecting date will have been deleted to make
room for the new device.
46, 49
The unit and device are too far apart. Position the Bluetooth device so that it is less than 10 m from this unit and
connect the device to this unit.
46, 49
There is a device (microwave oven, wireless LAN, etc.) outputs signals in
the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio frequency signals.
–
No sound is
heard or the
sound is
intermittent via
the Bluetooth
device.
The device is not set to send Bluetooth audio signals to the unit. Check that the Bluetooth function of the device is set properly. –
The device’s volume is set to minimum. Turn up the volume level on the device. –
Transmitted audio does not play. Play audio from the device selected with the input selector key. 49
The unit and device are too far apart. Move the Bluetooth device so that it is less than 10 m from this unit. 46, 49
There is a device (microwave oven, wireless LAN, etc.) outputs signals in
the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio frequency signals.
–
The Bluetooth connection of the unit with the device is disconnected. Perform Bluetooth connection operations again. 49
Attempted to establish a connection during playback with AirPlay. Playback with AirPlay cannot be transmitted. Terminate AirPlay playback
and try again to establish a connection.
49, 64
Problem Cause Remedy See page
The remote control does not work
and/or function properly.
The wrong distance or angle. The remote control functions within a maximum range of 6 m and no more
than 30 degrees off-axis from the front panel.
7
Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this unit.
Reposition this unit.
–
The batteries are weak. Replace all batteries. 7
Problem Cause Remedy See page
APPENDIX ➤ Troubleshooting En 97
Network
Problem Cause Remedy See page
The network feature does not
function.
The network parameters (IP address) have not been obtained properly. Enable the DHCP server function on your router and set “DHCP” in the
setup menu to “On” on the unit. If you want to configure the network
parameters manually, check that you are using an IP address which is not
used by other network devices in your network.
81
“Not connected” is displayed with
“Wireless (Wi-Fi)” configuration;
unable to connect to wireless
router (access point).
The wireless router’s MAC address filter is enabled. A connection cannot be established if the wireless router’s MAC address
filter is enabled. Check wireless router (access point) settings and try a
different connection method.
51, 81
“Not connected” is displayed with
“Wireless (Wi-Fi)” configuration
using the WPS function (“WPS
Button” and “PIN Code”) and
“Access Point Scan”; unable to
connect to wireless router
(access point).
The wireless router (access point) does not broadcast its SSID. A connection cannot be established if the wireless router (access point) is
configured so that it does not broadcast its SSID. Check wireless router
(access point) settings and try a different connection method.
54, 58
“Not connected” is displayed with
“Wireless (Wi-Fi)” configuration
using the WPS function (“WPS
Button” and “PIN Code”); unable
to connect to wireless router
(access point).
The wireless router (access point) uses WEP encryption. A connection cannot be established using the WPS function. Try a different
connection method.
54, 58
Playback stops unexpectedly and
files cannot be played
continuously.
The folder contains some files that cannot be played via the unit. Delete or move files (including video or hidden files) that cannot be played
via the unit from the folder. –
The unit does not detect the PC. The media sharing setting is not correct. Configure the sharing setting and select the unit as a device to which music
contents are shared.
61
Some security software installed on your PC is blocking the access of the
unit to your PC.
Check the settings of security software installed on your PC.
–
The unit and PC are not in the same network. Check the network connections of the unit and PC, and then connect the
unit and the PC to the same network.
–
The MAC address filter is enabled on the unit. In “MAC Address Filter” in the setup menu, disable the MAC address filter
or specify the MAC address of your PC to allow it to access to the unit.
81
The files in the PC cannot be
viewed or played back.
The files are not supported by the unit or the media server. Use the file format supported by both the unit and the media server.
61
APPENDIX ➤ Troubleshooting En 98
The Internet radio cannot be
played.
The selected Internet radio station is currently not available. There may be a network problem at the radio station, or the service may
have been stopped. Try the station later or select another station.
–
The selected Internet radio station is currently broadcasting silence. Some Internet radio stations broadcast silence at certain of times of the day.
Try the station later or select another station.
–
Access to the network is restricted by the firewall settings of your network
devices (such as the router).
Check the firewall settings of your network devices. The Internet radio can
be played only when it passes through the port designated by each radio
station. The port number varies depending on the radio station.
–
The dedicated apps for
mobile device does not detect
the unit.
The MAC address filter is enabled on the unit. In “MAC Address Filter” in the setup menu, disable the MAC address filter
or specify the MAC address of your mobile device to allow it to access to
the unit.
81
The unit and mobile device are not in the same network. Check the network connections and your router settings, and then connect
the unit and mobile device to the same network.
–
Firmware update via the
network (Network Update)
fails.
It may not be possible depending on the condition of the network. Update the firmware via the network (Network Update) again or use a USB
flash drive.
88
The iPod does not recognize
the unit when using AirPlay.
The unit and iPod/mobile device are connected to different SSIDs on the
same access point.
Check the network connections for the unit and your mobile device, and
connect them to the same SSID.
–
The app installed on a mobile
device does not recognize the
unit.
The unit cannot connect to
the Internet via a wireless
router (access point).
The wireless router (access point) is turned off. Turn on the wireless router (access point). –
The unit and the wireless router (access point) are too far apart. Place the unit and the wireless router (access point) closer to each other. –
There is an obstacle between the unit and the wireless router (access
point).
Move the unit and the wireless router (access point) in a location where
there are no obstacles between them.
–
Wireless network is not
found.
There is a device (microwave oven, wireless LAN, etc.) outputs signals in
the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio frequency signals.
–
Access to the network is restricted by the firewall settings of the wireless
router (access point).
Check the firewall setting of the wireless router (access point).
–
Problem Cause Remedy See page
APPENDIX ➤ Messages in the front panel display En 99
Messages in the front panel display
Message Description See page
ViewScreen This unit’s setup menu is displayed on the TV screen. Use the TV screen to configure settings. 67
Key Locked The keys on the unit are locked. Use the remote control. 86
Sleep XXmin The Auto Power Standby function will turn this unit off in XX minutes. 86
Protected SYSTEM MEMORY 1–3 and NET RADIO 1–3 are protected. 86
Disable Key operation is disabled. –
Status indicator on the wireless subwoofer kit SWK-W16
Indicator Status
Red Glows The SWK-W16 is in standby mode because the unit is turned off.
Green
Blinks A wireless connection between the unit and SWK-W16 is being established.
Blinks rapidly The unit and SWK-W16 are being paired.
Glows A wireless connection has been established.
APPENDIX ➤ When surround effect is not enough En 100
The unit achieves its surround sound effects by projecting sound beams which reflect
off walls. The sound beams are not reflected toward to the listening position caused by
furniture, etc., in the path of sound beams, or the room shape. In this case, the sound
may become unbalanced.
If the sound beams are not reflected toward to the listening position (figure 2), you can
adjust for this by installing the optional sound reflection board YRB-100.
• YRB-100 may not be available in some countries or regions.
Installing and adjusting the sound reflection board
YRB-100
1
Decide the position of the sound reflection board.
Install the sound reflection board as shown in the picture.
• Always hold the pole when moving the sound reflection board.
• Use “Channel Level” in the setup menu (p. 75) to determine the precise direction from which sounds
are difficult to hear.
When surround effect is not enough
Figure 1. Ideal condition Figure 2. Surround right beam is not
being reflected because there
is no wall.
Surround right is quieter than surround
(left), or surround right is in front of its
proper location.
Figure 3. With a sound reflection board
installed
The sound beam for surround right is
reflected correctly, and correct surround
sound effect is achieved.
Front side
Approx. 1.5 to 3 m
YRB-100
Front side
Install the panel front side of the
listening position, and outside of
the surround side panel.
Listening position
Surround side
Install the panel back side of the listening
position, and inside of the front side panel.
Surround side
Approx. 1 to 2.5 m
Recommended position for installation
APPENDIX ➤ When surround effect is not enough En 101
2
Use advanced setup (p. 86) to configure the sound reflection board.
Set “YRB FL” (FL), “YRB FR” (FR), “YRB SL” (SL), and “YRB SR” (SR) to
“YES” depending upon the position of the sound reflection board to be
installed.
Color bars are displayed across the entire TV screen. This makes it easier to
recognize whether the TV screen is reflected in the panel when determining
the proper angle of the panel in step 4, to the left or right.
3
Adjust the height.
Adjust the height of the sound reflection board panel based on the position of
the unit and the sound reflection board, as well as the listening position.
See the YRB-100 Owner’s Manual for more information.
4
Adjust the angle of the panel left or right.
Adjust the angle of the panel so that sound beams are reflected toward the
listening position.
Turn on the TV and dim the lights in the room. If you see the TV screen (color
bar display) reflected in the panel from your listening position, the angle of the
panel is properly adjusted.
See the YRB-100 Owner’s Manual for more information.
5
Press the z key to turn this unit off. Press it a second time to turn
this unit on again.
6
Plug the IntelliBeam microphone into this unit and then perform
“AUTO SETUP” (Beam+Sound optimize) from the “IntelliBeam”
menu (p. 31).
Be sure that the channels (FL, FR, SL, and SR) configured for the sound
reflection board are displayed for “YRB” on the SHOW RESULT screen.
An asterisk (*) is displayed with a channel exhibiting poor sound beam
reflection.
Should this occur, follow the instructions below to re-adjust the panel.
a Adjust the height and angle of the sound reflection board panel in accordance with
installation conditions.
b Use “Channel Level” in the setup menu (p. 75) to confirm that the test sound is
successfully reflected.
For greater precision, perform “AUTO SETUP” in the “IntelliBeam” menu, and then
confirm that the asterisk (*) is no longer displayed with the channel.
If the asterisk (*) continues to be displayed, or if there is still no test sound
reflected from the direction of the sound reflection board, follow directions in
the YRB-100 Owner’s Manual to adjust sound beams manually.
SHOW RESULT
MEASUREMENT COMPLETE.
ENVIRONMENT CHECK:Success
FRONT :Stereo
SURROUND :Beam
SUBWOOFER:Wired
YRB:FL SL*
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
Indicates poor reflection
APPENDIX ➤ Basic Knowledge of Surround Sound En 102
What is a Digital Sound Projector?
A typical surround sound playback system uses 5 to 7 speakers. To
configure a surround sound playback system that enables audio
playback in the vertical direction, 2 or more additional speakers
should also be installed above the listening position.
A highly realistic sound field can be created with multiple speakers
installed around the listening position as shown in the illustration
above. However, this can be difficult to do in a living room. The unit
utilizes “digital sound projector” technology, enabling it alone to
provide a realistic and engaging surround sound experience.
A digital sound projector provides optimal control over the delay time
for each of the compact speakers installed in orderly rows, and
drives the amplifier for each of these speakers, synthesizing audio
signals output from each speaker as highly focused sounds (sound
beams).
These focused sounds possess wave-like characteristics. When they
hit a hard wall or ceiling, they are reflected off the wall or ceiling. A
digital sound projector outputs sound beams from seven channels,
including front (left/right), center, surround (left/right), and height (left/
right) channels, by reflecting these beams off the walls and ceiling so
that sounds reach the listener from the appropriate direction. It
features a technology that enables true surround sound without
requiring the installation of speakers behind or to the sides of the
listener, or in the ceiling.
By combining sound beams coming from the front (left/right) and
back (left/right), it can also create two new audio channels for
surround sound playback using 7.1 channels in the horizontal
direction. With this configuration, the new audio channels output
sounds from surround sound channels, while sound beams coming
from behind the listening position (left/right) output sounds from
surround back channels.
Basic Knowledge of Surround Sound
Front speaker
Subwoofer
Surround
speaker
Center speaker
Surround back speakers
Front speaker
Height speakers
Surround
speaker
Digital amplifier
Speaker
Sound beams are emitted
in the target direction
The sound image of the system
APPENDIX ➤ Basic Knowledge of Surround Sound En 103
What is Object Based Audio?
With traditional audio technologies, which channels (speakers)
should output what types of sounds when creating audio sources
was pre-defined. This is called “channel-based audio”. In contrast,
new audio systems such as Dolby Atmos use a new technology
called object-based audio. This technology processes each sound
(e.g., the sound of a car or an actor’s voice) contained in an audio
source as an “object” and memorizes each object's sound changes
and positional changes in a sound field to control these changes
during playback. The greatest advantage of applying object-based
audio to a home surround sound system is the power to control the
audio output method based on device features and the number of
speakers used for playback. The unit adjusts sound beam output
according to the listening room setup. It calculates the movements of
an object according to each playback environment and reproduces
sound fields that best match the intentions of a sound director. It also
enables audio output in the vertical direction so that each sound
(object) in an audio source can freely move within a sound field.
Yamaha’s Audio Technologies
This unit features many more functions based on Yamaha’s superior
audio technologies.
This technology enhances and extends bass and treble, which tend
to be weak in digitally compressed formats such as MP3 used with
portable digital audio players and computers. This makes
compressed audio sound more musically dynamic.
This technology enables precise digital recreation of actual acoustic
environments found in well-known concert halls and movie theaters.
This is achieved using Yamaha’s exclusive sound field programs,
which are based on data measured in various sound fields, and with
which the amplitude, depth, and volume of sounds have been
adjusted.
CINEMA DSP 3D uses three-dimensional sound field data, including
vertical directional information, and further extends standard
CINEMA DSP, to make sound field effects more realistic and
three-dimensional.
Compressed Music Enhancer
CINEMA DSP/CINEMA DSP 3D
APPENDIX ➤ Glossary En 104
Sampling Frequency and Bit Depth
These are values that represent the amount of information used to convert analog signals to digital signals.
They may be expressed as 48kHz/24bit, for example.
• Sampling Frequency
This defines the number of samples per second (sampling a finite set of discrete values in an analog
signal). The higher the sampling rate, the broader the range of frequencies that can be played back.
• Bit Depth
This defines the amplitude value of sounds when quantifying analog signals as finite values. The higher
the bit depth, the deeper sounds are reproduced.
Deep Color
This is a video technology supported by the HDMI standard. It processes RGB or YCbCr signals at bit
depths of 10, 12, or 16 bits per color, whereas conventional formats utilize only 8-bit processing, enabling
reproduction of more colors. Its gamut is comprised of a billion or more colors, while the gamuts of
conventional formats are comprised of only millions of colors or less. This broader gamut results in more
precise reproduction of colors and greater detail in darker portions.
Dolby Atmos
Dolby Atmos is an object-based surround sound technology developed by Dolby Laboratories. Traditional
surround sound technologies record and control audio for each channel. Dolby Atmos records audio
content as a collection of many objects (a combination of audio information and information related to
movement of sound positions) and precisely controls content in accordance with various home theater
environments for an acoustic environment more realistic and three-dimensional than ever before. Another
advantage is the ability to record sounds coming from overhead. It was originally developed for movie
theaters, but can also be applied to home devices.
Dolby Atmos content is provided in the Dolby True HD format, including Dolby Atmos streams, or in the
Dolby Digital Plus format.
Dolby Digital
This is a compressed audio format for 5.1 channels. It was developed by Dolby Laboratories, and is widely
used with DVD discs.
Dolby Digital EX
This technology enables 6.1-channel playback for sources encoded in the Dolby Digital EX format. It takes
the Dolby Digital 5.1-channel setup one step further with an additional back surround channel.
Dolby Digital Plus
This is a compressed audio format for 7.1 channels developed by Dolby Laboratories. It is fully compatible
with Dolby Digital and is available for playback on Dolby Digital-enabled audio systems. It is widely used
with Blu-ray Discs.
Dolby Surround
This surround sound technology was developed by Dolby Laboratories to extend 2- to 7.1-channel content
in accordance with audio systems used for playback. It not only enables playback of Dolby Atmos content
but also extends traditional audio content to surround sound, including height channel audio, for 3D
surround sound playback.
Dolby TrueHD
This advanced lossless audio technology was developed by Dolby Laboratories for high-definition
disc-based media to deliver sounds that are identical, bit for bit, to studio masters for a great home theater
experience. It delivers up to 8 discrete channels of 24-bit/96-kHz (up to 6 discrete channels of 24-bit/192
kHz) audio simultaneously, and is widely used with Blu-ray Discs.
DTS Digital Surround
This is a compressed audio format for 5.1 channels developed by DTS. It is widely used with DVD discs.
DTS Express
This is a compressed audio format for 5.1 channels. It provides a higher compression ratio than the DTS
Digital Surround audio format, and was developed specifically for network streaming and Blu-ray Disc
secondary audio.
DTS-HD High Resolution Audio
This is a compressed audio format for 24-bit/96-kHz superior sound quality with 7.1 channels developed by
DTS. It is fully compatible with DTS Digital Surround, and is widely used with Blu-ray Discs.
DTS-HD Master Audio
This advanced lossless audio technology was developed by DTS for high-definition disc-based media to
deliver sounds identical, bit for bit, to studio masters for a great home theater experience. It delivers up to 8
discrete channels at 24-bit/96 kHz (up to 6 discrete channels at 24-bit/192 kHz) audio simultaneously, and is
widely used with Blu-ray Discs.
DTS Neo:6
This technology enables discrete 6-channel playback from 2-channel sources. There are two modes
available: “Music mode” for music sources and “Cinema mode” for movie sources. It provides a channel
split effect similar to sources recorded as discrete surround sound.
Glossary
APPENDIX ➤ Glossary En 105
DTS:X
DTS:X is the next generation object-based, multi-dimensional audio technology from DTS.
Unbound from channels, DTS:X conveys the fluid movement of sound to create an incredibly rich, realistic
and immersive soundscape - in front of, behind, beside and above the audience - more accurately than
ever before. DTS:X offers the ability to automatically adapt the audio to the speaker layout that best fits the
space, from a television’s built-in speakers to a home surround theater system to a dozen or more speakers
in a commercial cinema.
Immerse yourself at www.dts.com/dtsx
HDMI
High-Definition Multimedia Interface (HDMI) is a digital audio/video interface that has become an industry
standard around the world. It is capable of transmitting both digital video and audio signals intact via a
single cable. It is also compliant with the High-bandwidth Digital Content Protection (HDCP) standard. See
http://www.hdmi.org for more information.
Neural:X
Neural:X is the latest downmixing / upmixing and spatial remapping technology from DTS.
It is built in to DTS:X to provide upmix of Neural:X-encoded and non-encoded (PCM) data.
In DTS:X for AVRs and Sound Bars, Neural:X can produce up to 11.x channels.
Pulse Code Modulation (PCM)
This technology records analog audio signals in digital form, converts analog audio signals to digital audio
signals, and transmits analog audio signals in digital form. It is the underlying technology for all digital audio
signal systems, and is widely used with CDs, Blu-ray Discs, and many other types of media as a
uncompressed audio format known as Linear PCM.
x.v.Color
This is a color space supported by HDMI. It has become an international standard for video and offers a
broader gamut than does the sRGB standard for expression of colors never before possible. It expands the
color space while ensuring compatibility with the sRGB standard for more natural and vivid images.
Network information
SSID
SSID (Service Set Identifier) is a name that identifies a particular wireless LAN access point.
Wi-Fi
Wi-Fi is a technology that allows an electronic device to exchange data or connect to the Internet wirelessly
using radio waves. Wi-Fi offers the advantage of eliminating the complexity of making connections with
network cables by using wireless connection. Only products that complete Wi-Fi Alliance interoperability
tests can carry the “Wi-Fi Certified” trademark.
WPS
WPS (Wi-Fi Protected Setup) is a standard established by the Wi-Fi Alliance, which allows easy
establishment of a wireless home network.
APPENDIX ➤ Specifications En 106
Amplifier section
• Rated Output Power
Array speaker (1 kHz, 1% THD, 4 Ω) ............................ 74.8 W
Woofer (100 Hz, 1% THD 4 Ω) .............................17 W + 17 W
• Maximum Effective Output Power
Array speaker (1 kHz, 10% THD, 4 Ω) ............................. 88 W
Woofer (100 Hz, 10% THD 4 Ω) ...........................20 W + 20 W
Speaker section
• Array speaker for Vertical Sound Beam
Type: Acoustic suspension type
Driver: 2.8 cm (1-1/8 in) cone magnetic shielding type 6 x 2
(L/R)
Impedance: 4 Ω
• Array speaker for Horizontal Sound Beam
Type: Acoustic suspension type
Driver: 4.0 cm (1-1/2 in) cone magnetic shielding type x 32
Impedance: 4 Ω
• Woofer
Type: Acoustic suspension type
Driver: 11 cm (4-1/2 in) cone non-magnetic shielding type x 2
Impedance: 4 Ω
Input jacks
•Audio Input
Optical ............................................................ 2 (TV, OPTICAL)
Coaxial........................................................................ 1 (AUX2)
Analog .................................................................1 pair (AUX1)
• HDMI Input .................................................. 4 (HDMI IN 1 to 4)
Output jacks
• HDMI output (ARC).................................................................1
• Subwoofer output....................................................................1
Other jacks
• INTELLIBEAM MIC ..................................................................1
• SYSTEM CONNECTOR...........................................................1
• NETWORK...............................................................................1
• UPDATE ONLY.........................................................................1
• IR IN ........................................................................................1
• IR OUT.....................................................................................1
• RS-232C ..................................................................................1
Network
• Ethernet standard: 100BASE-T/10BASE-T
• Compatible with DLNA ver. 1.5
• Supported codecs
WAV (PCM format only) /AIFF/FLAC: up to 192 kHz
ALAC: up to 96 kHz
MP3/WMA/MPEG-4 AAC: up to 48 kHz
• AirPlay supported
• Internet Radio
Wireless LAN (Wi-Fi)
• Wireless LAN Standards ................................IEEE802.11b/g/n
• Radio Frequency Band ................................................2.4 GHz
• WPS (Wi-Fi Protected Setup)
...........................................Push-Button-Method, PIN Method
• Security Type..................WEP, WPA2-PSK (AES), Mixed Mode
Wireless LAN (Wireless Direct)
• Direct connection with mobile devices
Bluetooth
• Bluetooth version Ver. 2.1 +EDR
• Supported protocols
Receiving: A2DP, AVRCP
Transmitting: A2DP
• Supported codecs
Receiving: SBC, MPEG-4 AAC
Transmitting: SBC
• Wireless output ............................................. Bluetooth Class 2
• Maximum communication distance
.......................................................10 m (without obstructions)
• Supported content protection method.......SCMS-T (receiving)
General
• Power Supply
[U.S.A. and Canada models]..........................AC 120 V, 60 Hz
[Taiwan model]................................... AC 110–120 V, 50/60 Hz
[China model] ................................................. AC 220 V, 50 Hz
[Other models]................................... AC 220–240 V, 50/60 Hz
• Power Consumption
[U.S.A. and Canada models]............................................68 W
[Other models]..................................................................50 W
• Standby Power Consumption
HDMI Control Off, Network Standby Off .......................... 0.3 W
HDMI Control On, Network Standby Off .......................... 1.6 W
HDMI Control Off, Network Standby On
(Wired/Wi-Fi/Wireless Direct/Bluetooth) ......... 1.5/1.6/1.7/1.6 W
HDMI Control On, Network Standby On .........................3.1 W
• Dimensions (W × H × D)
Without Stands..........................................1100 x 212 x 93 mm
With Stands.............................................1100 x 216 x 122 mm
• Weight ........................................................................... 11.7 kg
Specifications
APPENDIX ➤ Specifications En 107
SWK-W16
• Power supply ......................................AC 220–240 V, 50/60 Hz
• Power consumption............................................................ 2 W
• Standby power consumption........................................... 0.5 W
•Output
Audio output (SUBWOOFER OUT/RCA/monaural) .................1
System control
(SYSTEM CONNECTOR/3.5 mm mini-jack/monaural).............1
• Radio frequency band................................................. 2.4 GHz
• Transmission range ..........Approx. 10 m (without interference)
• Dimensions (W × D × H) excluding projections
.............................................................210 × 53.5 × 123.5 mm
• Weight............................................................................0.65 kg
Specifications are subject to change without notice.
APPENDIX ➤ Specifications En 108
HDMI signal
• Audio signals
* DTS:X may be provided with a firmware update.
• Refer to documentation supplied with the playback device, and set the device appropriately.
• When CPPM copy-protected DVD-Audio is played back, video and audio signals may not be output
depending on the type of the DVD player.
• This unit is not compatible with HDCP-incompatible HDMI or DVI devices. Refer to documentation supplied
with the HDMI or DVI device for HDCP compatibility.
• To decode audio bitstream signals on this unit, set the input source device appropriately so that the device
outputs the bitstream audio signals directly (does not decode the bitstream signals on the device). Refer to
documentation supplied with the device for details.
• Video signals
This unit is compatible with the following video signals.
• Deep Color
• x.v.Color
• 3D video signal
This unit is compatible with the following resolutions.
• The resolution of transmitted video signal varies according to specifications of the TV connected to this
unit.
Digital audio signal
• Optical/coaxial
•HDMI (ARC)
Audio signal types Audio signal formats Compatible media
2ch Linear PCM 2ch, 32–192 kHz, 16/20/24 bit CD, DVD-Video, DVD-Audio, etc.
Multi-ch Linear PCM 8ch, 32–192 kHz, 16/20/24 bit
DVD-Audio, Blu-ray disc, HD DVD,
etc.
Bitstream (SD Audio) Dolby Digital, DTS DVD-Video, etc.
Bitstream (HD Audio)
Dolby Atmos, Dolby TrueHD,
Dolby Digital Plus, DTS:X*,
DTS-HD Master Audio, DTS-HD
High Resolution Audio, DTS
Express
Blu-ray disc, HD DVD
•VGA
•480i/60Hz
•480p/60Hz
•576i/50Hz
•576p/50Hz
• 720p/60 Hz, 50 Hz
• 1080i/60 Hz, 50 Hz
• 1080p/60 Hz, 50 Hz, 30 Hz, 25 Hz, 24 Hz
• 4K/60 Hz, 50 Hz, 30 Hz, 25 Hz, 24 Hz
Audio signal types Audio signal formats Compatible media
2ch Linear PCM 2ch, 32–96 kHz, 16/20/24 bit
CD, DVD-Video, DVD-Audio,
etc.
Bitstream
Dolby Digital, Dolby Digital
Surround EX, DTS, DTS-ES
DVD-Video, etc.
Audio signal types Audio signal formats Compatible media
2ch Linear PCM 2ch, 32–192 kHz, 16/20/24 bit TV
Bitstream
Dolby Digital Plus, Dolby Digital,
DTS
TV
APPENDIX ➤ Specifications En 109
The “ ” logo and “IntelliBeam” are trademarks of Yamaha
Corporation.
The “ ” logo and “Cinema DSP” are registered
trademarks of Yamaha Corporation.
Manufactured under license from Dolby Laboratories. Dolby, Dolby
Atmos, Dolby Surround, Surround EX and the double-D symbol are
trademarks of Dolby Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under
license from DTS, Inc. DTS, the Symbol, DTS in combination with the
Symbol, DTS:X, and the DTS:X logo are registered trademarks or
trademarks of DTS, Inc. in the United States and/or other countries.
© DTS, Inc. All Rights Reserved.
“HDMI,” the “HDMI” logo and “High-Definition Multimedia Interface”
are trademarks, or registered trademarks of HDMI Licensing LLC.
“x.v.Color” is a trademark of Sony Corporation.
The Bluetooth
®
word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by Yamaha
Corporation is under license.
Bluetooth
Bluetooth is a technology for wireless communication employing the
2.4 GHz frequency band, which can be used without a license.
Handling Bluetooth communications
• The 2.4 GHz band used by Bluetooth compatible devices is a radio
band shared by many types of equipment. While Bluetooth
compatible devices use a technology minimizing the influence of
other components using the same radio band, such influence may
reduce the speed or distance of communications and in some
cases interrupt communications.
• The speed of signal transfer and the distance at which
communications is possible differs according to the distance
between the communicating devices, the presence of obstacles,
radio wave conditions and type of equipment.
• Yamaha does not guarantee all wireless connections between this
unit and devices compatible with Bluetooth function.
Apple
iTunes, Mac, AirPlay, iPad, iPhone, iPod, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other countries.
MusicCast is a trademark or registered trademark of Yamaha
Corporation.
DLNA™ and DLNA CERTIFIED™ are trademarks or registered
trademarks of Digital Living Network Alliance. All rights reserved.
Unauthorized use is strictly prohibited.
Windows™
Windows is a registered trademark of Microsoft Corporation in the
United States and other countries.
Internet Explorer, Windows Media Audio and Windows Media Player
are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Android™
Android and Google Play are trademarks of Google Inc.
The Wi-Fi CERTIFIED Logo is a certification mark of Wi-Fi Alliance.
The Wi-Fi Protected Setup Identifier Mark is a certification mark of
Wi-Fi Alliance.
Wi-Fi, Wi-Fi Alliance, Wi-Fi CERTIFIED, Wi-Fi Protected Setup, WPA
and WPA2 are trademark or registered trademark of Wi-Fi Alliance.
“Blu-ray Disc™”, “Blu-ray™”, and the logos are trademarks of the
Blue-ray Disc Association
Explanations regarding GPL
This product utilizes GPL/LGPL open-source software in some
sections. You have the right to obtain, duplicate, modify, and
redistribute this open-source code only. For information on GPL/
LGPL open source software, how to obtain it, and the GPL/LGPL
license, refer to the Yamaha Corporation website
(http://download.yamaha.com/sourcecodes/musiccast/).
Bluetooth protocol stack (Blue SDK)
Copyright 1999-2014 OpenSynergy GmbH
All rights reserved. All unpublished rights reserved.
APPENDIX ➤ Index En 110
Numerics
2-channel playback 41
3D surround 5
3D surround sound playback 38
3D video 22
4K video 22
A
Access point scan 54
Adaptive DRC 75
ADVANCED 86
Advanced setup menu 86
AirPlay 64
Audio Assign 85
Audio Delay 85
Audio Return Channel (ARC) 22
Audio signal information 79
AUTO POWER STANDBY 87
Auto setup (IntelliBeam) 30
B
Bass 85
Beam optimize only 33
Beam Travel Length 71
Beam+Sound optimize 33
Bluetooth 46
Bluetooth (receiving audio) 47
Bluetooth (transmitting audio) 49
Bluetooth settings 83
Bracket 17
Brightness adjustment (front panel display and
indicators) 78
C
Cardboard microphone stand 30
Channel level 43
Channel Out 73
Channel output level adjustment (test sound) 75
CINEMA DSP 103
CINEMA DSP 3D 103
CLEAR VOICE 42
Compressed Music Enhancer 42
D
Deep Color 104
Default gateway 80, 81
DHCP 51, 81
Dialog position 42
Digital Sound Projector 102
Dimmer 78
Distance Unit 78
DLNA 61
DNS server (P) 80, 81
DNS server (S) 80, 81
Dolby Atmos 104
Dolby Digital 104
Dolby Digital EX 104
Dolby Digital Plus 104
Dolby Surround 104
Dolby TrueHD 104
DTS 76
DTS Digital Surround 104
DTS Express 104
DTS Neo:6 104
DTS:X 76, 105
DTS-HD High Resolution Audio 104
DTS-HD Master Audio 104
Dynamic Range 76
E
Eco function 44
Encryption method 54, 56, 58, 59
Entertainment 40
Error buzzer 32
Error message 34
F
File format (computers/NAS) 61
Firmware of this unit 79, 87
Firmware update 82, 88
Front panel 8
H
HDCP version 2.2 22
HDMI 105
HDMI audio assignment 85
HDMI Audio Out 77
HDMI cable 22, 23
HDMI control 35, 77
Height channels 38, 102
HOME THEATER CONTROLLER (WLAN) app 5
I
Installing the unit 12
IntelliBeam 30
INTELLIBEAM MIC jack 8
IntelliBeam microphone 30
Internet radio 62
IP address 80, 81
iPod music (AirPlay) 64
iTunes music (AirPlay) 64
L
Language (OSD) 29
Language for menu display 78
Index
APPENDIX ➤ Index En 111
M
MAC address 80
MAC address filter 51, 81
Manual setting (wireless connection) 56
Media sharing setup 61
Menu screen 28
Mobile device music 66
Mounting the unit on a wall 17
Movie 40
MP3 42
Music 40
MusicCast CONTROLLER app 5
N
Network information 80
Network name 82
Network standby 82
Neural:X 76, 105
O
Option menu 84
OSD Language 78
Output timing adjustment (image and sound) 85
P
Power cable 27
Pulse Code Modulation (PCM) 105
R
Rear panel 9
Reflection board 100
Remote control 7, 10
Remote control sensor 8
S
Sampling frequency 79
Security 80
Security key 57, 59
Security software 51
Setup menu 67
Sharing Wi-Fi settings (iOS device) 29, 53
Sound optimize only 33
SSID 54, 55, 80, 105
Stands 16
STATUS indicator 8
Stereo playback 41
Subnet mask 51, 80
Subwoofer settings 74
Subwoofer volume 37
Surround sound 39
System memory 45
T
Target playback mode 41
Test sound 75
Tone adjustment 85
Top panel 8
Treble 85
TV 28, 35
TV audio input 77
V
Video signal information 79
Volume 37
Volume Trim 85
vTuner 62
vTuner ID 80
W
Wi-Fi 105
Wired network connections 27, 52
Wireless Direct 59
Wireless network 52
Wireless subwoofer kit 25
WMA 61
WPS 105
WPS PIN code 58
X
x.v.Color 105
© 2015 Yamaha Corporation YH433C0/EN2
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
in andere talen
- English: Yamaha YSP-5600 User manual
- italiano: Yamaha YSP-5600 Manuale utente
- русский: Yamaha YSP-5600 Руководство пользователя
- français: Yamaha YSP-5600 Manuel utilisateur
- español: Yamaha YSP-5600 Manual de usuario
- Deutsch: Yamaha YSP-5600 Benutzerhandbuch
- dansk: Yamaha YSP-5600 Brugermanual
- suomi: Yamaha YSP-5600 Ohjekirja
- svenska: Yamaha YSP-5600 Användarmanual
- Türkçe: Yamaha YSP-5600 Kullanım kılavuzu
Gerelateerde artikelen
-
Yamaha YAS-306 de handleiding
-
-
-
-
-
Yamaha YSP-2700 Handleiding
-
-
-
Yamaha YAS-106 de handleiding
-
Yamaha SRT-1000 de handleiding