ab Naida CI Q90 Handleiding

Merk: ab

Model: Naida CI Q90

Type: Handleiding

Naída CI Sound Processor user guide

English, Français, Español, Deutsch, Nederlands, Português

029-M497-85 Rev A

user guide

for the Naída CI Q90 Sound Processor

2 Naída CI Q90 Sound Processor User Guide

Labeling

Labeling symbols and their meanings:

*Only applicable if ‘refurbished’ is noted on the shipping label

Warning and Cautions

WARNINGS

• CHOKING HAZARD–contains small parts that pose a hazard of inhalation.

• Do not use or store the AB myPilot in shirt pockets if the recipient has a pacemaker, as

there is potential for interference. Contact a health care professional for more information.

European Community Mark of Conformity. Authorized to afﬁx the CE Mark in 2015

Model number

Date of manufacture

Serial number

Manufacturer

Type of Protection: B

Store at temperatures between -20˚C (-4˚F) and +55˚C (131˚F)

Fragile

Do not get wet

See Instructions for Use

Suitable for atmospheric range between 70 kPa and 106 kPa, which is equivalent to

3000 m above sea level to 380 m below sea level

Suitable for exposure to relative humidity between 0-95%

Dispose of in accordance with applicable national and local regulations

The Naída CI Q90 carries a rating of IP57. This rating indicates that the Naída CI Q90 is

protected

against the following conditions: protection against dust, failure due to one time immersion

for 30 minutes to a depth up to 1m and after drying overnight in a dry and store unit

IP57

Refurbished*

Naída CI Q90 Sound Processor User Guide 3

• Do not use a ComPilot if recipient has a pacemaker, as there is potential for

interference. Contact a health care professional for more information.

• Ensure appropriate supervision when child is wearing the Naída CI Q90 sound

processor and accessories.

• Keep batteries and accessories out of children’s reach as they may pose a choking hazard.

• If any parts are swallowed consult a physician or hospital immediately.

• Do not leave children unattended with or allow them to play with batteries.

• Do not place batteries in your mouth.

• Do not chew or swallow batteries. If this occurs, seek immediate medical attention.

• Do not allow children to play with or operate the drying system unattended.

• Using your sound processor and accessories in a manner other than their

intended use (e.g. placing them in your mouth or chewing them) may cause

bodily harm.

• Do not recharge disposable batteries.

• Do not allow leaking battery ﬂuid to come into contact with skin, mouth, or eyes.

• Do not expose batteries to heat (e.g., do not store in direct sunlight or in a hot car).

• Do not dispose of batteries in ﬁre.

• Do not allow children to charge batteries unattended.

• Do not use any power supply with the sound processor, AB myPilot remote

control or ComPilot unless it is supplied by Advanced Bionics or Phonak. If

needed, contact Advanced Bionics for a power supply replacement.

• Do not use the AB myPilot or the ComPilot when they are plugged in to power

sources such as wall outlets or USB compatible power sources such as laptops.

• The ComPilot comes with a neck loop antenna. Do not touch the neck loop

connectors at the same time.

• Power supplies and battery chargers should be operated in an open area to ensure

adequate airﬂow. While, to date, no injuries have been reported, components may

become hot during normal use or in the event of a fault. If the device’s temperature

results in discomfort or pain when touched, disconnect the power source and

contact your local Advanced Bionics representative.

4 Naída CI Q90 Sound Processor User Guide

CAUTIONS

• Remove external equipment to stop stimulation if sounds cause discomfort.

• It is important for the headpiece to have the correct magnet strength to

avoid discomfort or retention issues. If an insufﬁcient number of magnets

are used, the headpiece may fall off more than is acceptable. If too many

magnets are used, the recipient may experience irritation or discomfort. Consult

a clinician if there are any concerns regarding magnet strength. If deemed

appropriate, an audiologist may insert additional magnets or remove magnets

from the headpiece. Do not place additional magnets in the headpiece unless

under the direction of a cochlear implant professional. If the recipient experiences

any redness, irritation, or discomfort, discontinue use of the headpiece immediately

and contact a cochlear implant center. See the headpiece Instructions for Use for

additional information regarding adjustment of headpiece magnet strength.

• If the sound processor or accessories become unusually hot or warm, discontinue

use immediately and contact Advanced Bionics or a clinician.

• Store additional headpieces away from items with magnetic strips (e.g. credit

cards, hotel room key cards), as this may de-magnetize cards.

• Portable and mobile RF communications equipment, including radios and

cellular phones, may affect sound quality of the Naída CI Q90 sound processor and

accessories; however, there is no safety hazard associated with such equipment.

• The Naída CI Q90 sound processor and accessories should be used in accordance

with the electromagnetic compatibility (EMC) information provided in the Guidance and

Manufacturer’s Declaration section of the Instructions for Use.

• Only use the charger provided for charging AB PowerCels. Do not use it to

charge other batteries. Do not try to charge Naída CI Q90 PowerCels using a charger

other than the one provided by Advanced Bionics.

• Remove batteries from your sound processor when they are drained to prevent

damage from possible leaking.

• Do not expose any part of the Naída CI Q90 sound processor or accessories to

extreme heat, such as an oven, microwave, or hair dryer.

• Only charge batteries using charger(s) recommended by the manufacturer.

• Do not use your AB myPilot or ComPilot accessories when instructed not to use

wireless electronic devices, such as on airplanes.

• The AB myPilot should not come within 1/2” (1 cm) of the Naída CI Q90 processor

Naída CI Q90 Sound Processor User Guide 5

while stimulating the implant. Doing so could cause the implant and sound

processor to lose lock. If this happens, power down the processor and power back

on (by disengaging the battery and reattaching).

• The digitally-coded, inductive transmission technology used in this device is

extremely reliable and experiences virtually no interference from other devices.

It should be noted, however, that when operating the device near a computer

terminal or other strong electromagnetic ﬁelds, it may be necessary to be at least

24” (60 cm) away to ensure proper operation. If the Naída CI Q90 does not respond

to the implant device because of an unusual ﬁeld disturbance, move away from

the disturbing ﬁeld.

• If the AB myPilot stops being able to transmit commands to the sound processor,

it may be necessary to re-pair the AB myPilot with your sound processor. Consult the

Pairing to the AB myPilot section of this user manual.

• If volume commands from your AB myPilot to your sound processor seem erratic,

re-pair the AB myPilot and the Naída CI Q90.

• NOTE: When streaming audio with the ComPilot, if your headpiece becomes

unlocked, turn off the ComPilot prior to re-locking your headpiece. Not doing so

may prevent the sound processor from communicating with your implant.

• Patients are advised that the use of WindBlock, EchoBlock and/or SoundRelax

may affect the quality of sound.

Electrostatic Discharge (ESD)

High levels of static electricity may damage electronic components of your sound processor or

implant. Care should be taken to avoid exposure of the system to static electricity. ESD is present

when you feel a spark jump from your body or your hair

stands on-end.

The following are examples of situations where high levels of electrostatic charge may be created:

• Walking, crawling, or sliding on carpets.

• Sliding on plastic slides.

• Exiting an automobile.

• Pulling sweaters on and off.

• Touching TV or computer screens.

• Removing bedding materials.

6 Naída CI Q90 Sound Processor User Guide

To reduce the likelihood of electrostatic discharge damage:

• Touch a person or object with your ﬁngers prior to touching your or your child’s headpiece, cable,

or sound processor.

• Touch metal surfaces with your hand prior to allowing equipment to contact the metal surface.

This is particularly important on the playground where high levels of static electricity can be

generated. It is important to discharge any static electricity by touching a metal surface with your hand

prior to allowing the sound processor, cable, or headpiece to come into contact with the metal

surface.

• Take care to avoid contact between your cochlear implant equipment and metal surfaces

when exiting a vehicle.

• Remove cochlear implant equipment prior to removing clothing that may contain electric

charge (e.g. sweaters).

• Do not touch TV or computer screens. If screens are touched, be sure to touch an object

other than your implant system to discharge any charge build-up prior to touching any part

of your implant system.

• Use fabric softener on clothing and bedding.

Airport Security Metal Detectors

Metal detectors and security scanners, including full body scanners, will not damage your

implant system; however, metal detectors may be activated as you pass through. To avoid

hearing any unwanted sound when walking through metal detectors or security scanners, you

should reduce the volume on the sound processor or remove your headpiece.

Ultrasonic Sensors

Ultrasonic sensors, sometimes used in lighting sensors and security systems, will not damage

your implant system; however, they may be picked up by the headpiece microphone and lead

to distorted sound quality when you operate your sound processor in the immediate vicinity

of such a sensor. Additionally, if the ultrasonic sound is of a very high intensity, the processor

system microphone may become damaged. To avoid hearing any unwanted sound, you should

reduce the volume on your sound processor or remove your headpiece when passing near an

ultrasonic sensor (e.g. in entrances to libraries).

X-ray Machines

X-ray machines will not damage your sound processor or implant, but may damage your Naída

CI Q90 and head piece microphones. Avoid placing any system microphones in any checked

or carry-on baggage that is screened with X-ray. During airport security screenings, the sound

processor and microphone should be worn through the metal detector or examined by hand.

Table of Contents

Introduction ...............................................................................................................................10

Purpose of this Guide .....................................................................................................................10

About the Naída CI Q90 Sound Processor .........................................................................10

The Naída CI Q90 Sound Processor ................................................................................11

The Naída CI Q90 Sound Processor and Accessories Overview ..........................12

The Naída CI Q90 ...........................................................................................................................12

The Universal Headpiece .............................................................................................................13

AB myPilot ............................................................................................................................................ 13

ComPilot ................................................................................................................................................14

Naída CI Listening Check ............................................................................................................. 14

AquaCase™ Container ...................................................................................................................15

Phonak DECT Phone ......................................................................................................................15

Naída CI Q90 Sound Processor Features ......................................................................16

auto UltraZoom .................................................................................................................................16

StereoZoom ......................................................................................................................................... 16

UltraZoom ............................................................................................................................................ 16

WindBlock .............................................................................................................................................16

SoundRelax ..........................................................................................................................................16

EchoBlock .............................................................................................................................................17

DuoPhone ............................................................................................................................................17

ZoomControl .......................................................................................................................................17

QuickSync .............................................................................................................................................17

Assembling the Naída CI Q90 ........................................................................................... 17

Connecting the Universal Headpiece (UHP) Color Caps ............................................ 18

Connecting the Headpiece to the Naída CI Q90 ............................................................18

Removing the Headpiece from the Naída CI Q90 .........................................................19

Connecting the T-Mic™ 2/Earhook ..........................................................................................19

Removing the T-Mic 2/Earhook.................................................................................................20

Attaching the T-Mic 2 Cover .......................................................................................................21

Removing the T-Mic 2 Cover ......................................................................................................21

Wearing the Naída CI Q90 .................................................................................................22

Using the Clip .....................................................................................................................................22

Inserting the Naída CI Q90 in the Clip ................................................................................. 23

Removing the Naída CI Q90 from the Clip ........................................................................24

Using the Naída CI Q90 Sound Processor ....................................................................24

Powering the Naída CI Q90 .......................................................................................................24

Removing the Battery .....................................................................................................................25

Replacing the Battery ..................................................................................................................... 26

Understanding Naída CI Q90 LEDs .......................................................................................27

Understanding Internal Alarms .................................................................................................28

Using Naída CI Headpieces ................................................................................................28

The Universal Headpiece .............................................................................................................28

Replacing the RF Cables ...............................................................................................................28

Adjusting Headpiece Magnet Strength ................................................................................29

Removing Headpiece Color Caps ............................................................................................ 30

Adjusting Controls on the Naída CI Q90 .......................................................................30

Changing Programs ........................................................................................................................ 30

Changing Volume.............................................................................................................................31

Changing Sensitivity ........................................................................................................................32

Connectivity ...............................................................................................................................32

Using FM/Roger ................................................................................................................................32

Pairing to the AB myPilot ..............................................................................................................35

The Naída CI Listening Check and Listening Check Earbuds ................................38

Listening to the Microphone(s) and Auxiliary Inputs .....................................................38

Using the Telephone .......................................................................................................................41

Telephone Tips ................................................................................................................................... 42

Telecoil ....................................................................................................................................................42

Battery Information ................................................................................................................ 43

Assembling the PowerCel™ Charger ......................................................................................44

Inserting the PowerCels into the Charger ............................................................................45

Removing the PowerCels from the Charger........................................................................45

The Zn-Air Battery Pak ...................................................................................................................46

Inserting Zn-Air Batteries ..............................................................................................................46

Inserting Zn-Air Batteries (Tamperproof Cartridge) ........................................................47

Charger LED (Light Emitting Diode) Indicator ..................................................................48

Warnings ............................................................................................................................................... 49

Cautions ................................................................................................................................................49

Using Naída CI Accessories ................................................................................................49

Headpieces .......................................................................................................................................... 50

ComPilot ................................................................................................................................................50

Naída CI Listening Check and Listening Check Earbuds.............................................50

Audio Accessories ............................................................................................................................ 51

Color Customization ........................................................................................................................51

Naída CI Carrying Case ................................................................................................................52

Drying System .....................................................................................................................................52

IP Rating Information ............................................................................................................53

Care of the Naída CI Q90 Sound Processor and Accessories ................................53

Changing Microphone Covers ...................................................................................................53

Recommended Naída CI Q90 Operating and Storage Temperatures ................ 55

Approved Power Sources ..............................................................................................................55

Troubleshooting the Naída CI Q90 .................................................................................. 55

Troubleshooting Naída CI Q90 LEDs ....................................................................................57

Troubleshooting Naída CI Q90 Internal Alarms .............................................................. 59

Guidance and Manufacturer’s Declaration .................................................................. 60

Electromagnetic Emissions .......................................................................................................... 60

Electromagnetic Immunity ..........................................................................................................60

Separation Distances between RF Communications

Equipment and Naída CI Q90...................................................................................................61

Compatibility Tables ........................................................................................................................ 62

Cleaning & Maintenance .............................................................................................................63

Performance Data ..................................................................................................................63

HiRes™ and HiRes Fidelity120™ Sound Processing........................................................63

Contact Us .................................................................................................................................65

10 Naída CI Q90 Sound Processor User Guide

Sound Processor

Power Source

(PowerCel)

Universal Headpiece (UHP)

Introduction

Purpose of this Guide

This user guide is designed to help recipients, parents, and caregivers understand the use and

care of the Naída CI Q90 sound processor. The Naída CI Q90 sound processor represents the

latest in high-performance sound processing from Advanced Bionics. As the most advanced

sound as well as the smallest processors ever developed by AB, this latest generation in hearing

solutions features state-of-the-art technologies exclusively available from Advanced Bionics and

Phonak for the best possible hearing experience.

The Naída CI Q90 provides access to the latest sound processing innovations by Advanced

Bionics, the market leader in performance. This guide will provide all of the information needed

to use and care for the Naída CI Q90 and its accessories. In addition, this guide will provide

information for troubleshooting basic issues related to the Naída CI Q90, as well as important

safety information. Please read the entire manual prior to using the Naída CI Q90.

About the Naída CI Q90 Sound Processor

The Naída CI Q90 sound processor is one part of a complete cochlear implant system that

enables hearing. The other necessary parts of the system are the Implantable Cochlear

Stimulator (ICS), headpiece, and headpiece cable.

The sound processor consists of two parts: the sound processor and battery power source. There

are seven battery options, including two sizes of Lithium Ion rechargeable PowerCel™ batteries*,

two sizes of Lithium Ion rechargeable PowerCel Mini batteries* and a Zn-Air Battery Pak. The

recipient also has the option of wearing the power source completely off the ear by using either

the AAA/03 PowerPak or the Power Adapter. Please refer to the AAA PowerPak and Power

Adapter Instructions For Use for more details on these products.

* PowerCels refers to Naída CI PowerCel and Naída CI PowerCel Mini unless otherwise noted

Naída CI Q90 Sound Processor User Guide 11

AB myPilot

ComPilot

LEDs

The Naída CI Q90 includes programmable, multi-color light-emitting diode (LED) indicators

and programmable internal alarms for easy status updates and troubleshooting information.

Additional features include remote control access through the AB myPilot remote control and

the ability to stream from the Phonak ComPilot.

The Naída CI Q90 Sound Processor

This section will familiarize you with the Naída CI Q90 Sound Processor and Accessories

Sound Processor

Battery Cartridge

Program Button

Volume Control and Tri-Colored LEDs

(green, orange, red)

Volume Control

Universal Headpiece (UHP)

Microphone

Headpiece Cable

Phonak Dual-Microphone Technology

(front and back microphones)

AB’s Patented T-Mic™ 2 microphone

12 Naída CI Q90 Sound Processor User Guide

The Naída CI Q90 Sound Processor and Accessories Overview

The Naída CI Q90 is the newest and most advanced cochlear implant sound processor

available.

As evidence of Advanced Bionics’ dedication to providing the best hearing possible, the Naída

CI Q90 provides access to AutoSound™ technology, which dynamically adapts to every listening

environment, automatically adjusting volume levels to optimize hearing. The Naída CI Q90 is

also capable of utilizing all approved sound processing options offered by Advanced Bionics.

Depending on the country in which you live, this may include HiRes™-S, HiRes™-P, HiRes Fidelity

120™, ClearVoice™, HiRes™ Optima, CIS, and MPS.

The Naída CI Q90

The Naída CI Q90 is a miniature computer that converts sound picked up by the microphone

into electrical signals that are used by the cochlear implant to enable hearing. It is able to store

up to ﬁve (5) user-selectable programs for optimal hearing across all listening environments.

The Naída CI Q90 has diagnostic indicators, such as LEDs and internal audible alarms. The

Naída CI Q90 LEDs provide important information about Naída CI Q90 status, battery life,

program position, audio input, and Naída CI Q90 error conditions. Internal alarms provide a

discreet way for adult recipients to get important information about battery status, program

number, and volume level. For more information, refer to the Naída CI Q90 LEDs and Internal

Alarms sections of this User Guide.

The Naída CI Q90 can be programmed using Intellilink™ safety feature to prevent use by

a cochlear implant other than the one for which it has been programmed. IntelliLink is an

important safety feature for very young children and bilateral implant recipients.

The Naída CI Q90 can also be programmed bilaterally allowing the recipient access to up to

ten programs on a single processor, up to ﬁve programs for the left ear and up to ﬁve programs

for the right ear. When programmed bilaterally by your clinical professional, the Naída CI Q90

will detect which ear it is worn on and provide access to the appropriate programs for that ear.

Tri-Colored LEDs

(green, orange, red)

Naída CI Q90 Sound Processor User Guide 13

The Universal Headpiece

The Universal Headpiece includes a coil that transmits sound signals and power to the implant,

as well as a magnet well, which houses the necessary number of magnets to ensure the

headpiece stays on throughout the day. The headpiece is covered by a Color Cap, which snaps

securely in place. The headpiece also functions as a sound input source, having a microphone

embedded in it. The microphone picks up sound from the environment and transfers it to the

sound processor via a detachable cable. Once the sound processor has converted the sound

into electric signals, it sends the information to the implant via the cable and headpiece. The

cables come in a variety of colors and lengths to suit all needs. The Naída CI Q90 works with

the Universal Headpiece.

The Universal Headpiece (UHP), works with all Advanced Bionics’ sound processors, and is

intended for use with the Naída CI Q90 outside of water environments.

For more information, refer to the Replacing Headpiece Cables section of the User Guide or the

UHP and/or Cable Instructions for Use.

AB myPilot

The AB myPilot is an advanced remote control that leverages Phonak technology to enable

wireless communication for unilateral and bilateral Naída CI recipients. The AB myPilot provides

convenient controls to manipulate program, volume, sensitivity, source-speciﬁc listening checks,

and ZoomControl for the Naída CI Q90. The AB myPilot also has the ability to provide status

and battery information for Naída CI processors. For bilateral Naída CI users, AB myPilot offers

one-touch binaural controls, allowing changes to be made to both processors at once.

Color Cap

Microphone Cable Connection Port

14 Naída CI Q90 Sound Processor User Guide

ComPilot

The ComPilot allows unparalleled connectivity for Naída CI recipients, connecting them

wirelessly to Bluetooth® enabled phones and devices or MP3 players for speech or stereo music.

It is also compatible with Phonak’s portfolio of FM receivers via a euro socket. Additionally,

when unpaired, the ComPilot is able to stream to compatible Phonak instruments. This allows

bimodal wearers -- people who wear a Naída CI on one ear and a Phonak compatible hearing

instrument on the other ear -- access to bilateral wireless streaming.

When the ComPilot is paired to the Naída CI, it provides remote control functions to adjust the

Naída CI for increased listening comfort in addition to wireless streaming. When paired, you are

able to make program and volume changes via the ComPilot only to the Naída CI. If you are

bilaterally implanted, changes can be made to both Naída CI processors simultaneously. The

ComPilot also connects both Naída CI processors wirelessly to other communication and audio

devices, allowing you to hear the signal in both ears.

Naída CI Listening Check

The Naída CI Listening Check’s unique design makes conducting a diagnostic check of the

microphone and audio input sources easy and accessible. The Module itself does not have

a power source, as it relies solely on power from the Naída CI power sources (PowerCels,

Zn-Air Battery Pak, AAA/03 PowerPak or Off-the-Ear Power Options). The Naída CI Listening

Check allows an unaided listener to listen to the exact microphone conﬁgurations the recipient

is using. Alternatively, if the recipient owns an AB myPilot, the unaided listener can do a listening

check of all audio sources independently by selecting them individually on the AB myPilot menu.

Naída CI Q90 Sound Processor User Guide 15

AquaCase™ Container

The AquaCase delivers a durable, wearable, and swimmable solution for uncompromised

hearing in and out of water. The AquaCase carries an IP 68 rating for the ultimate protection

against water, sweat, dust, and sand. From farms and construction sites to pools and

playgrounds, you can rest assured your processor is protected in any environment.

Phonak DECT Phone

The Phonak DECT phone is a cordless phone that streams wirelessly to one or both implants

simultaneously. This phone also has the ability to stream to a compatible Phonak hearing

instrument. Apart from the streaming function, the phone has a regular acoustic output and

can therefore be used by non-implant users as well. Up to six handsets can be connected to one

base providing functionality for both home or small-ofﬁce use.

16 Naída CI Q90 Sound Processor User Guide

Naída CI Q90 Sound Processor Features

The Naída CI Q90 provides advanced Phonak features, including UltraZoom, auto UltraZoom,

Front/Back ZoomControl, WindBlock, EchoBlock, and SoundRelax. Bilateral Naída CI Q90 users

may also access Phonak Binaural VoiceStream Technology™ features , including DuoPhone,

Left/Right ZoomControl, StereoZoom, and QuickSync.

These features are programmed by your implant professional in the SoundWave™ professional

suite software.

The Naída CI Q90 includes:

• Smallest form factor of the Naída CI series of sound processors.

auto UltraZoom

auto UltraZoom is designed to be automatically activated, and like UltraZoom

it works adaptively to allow the listener to focus on voices coming from the front.

Even as noise from the side and back moves or changes, it is reduced to allow for

easier listening.

StereoZoom (bilateral only feature)

StereoZoom is designed to enable both Naída sound processors to work together

to focus on the person directly in front of you allowing you to hear them in very

noisy situations.

UltraZoom

UltraZoom works adaptively, and is designed to allow you to focus on voices

coming from the front. Even as noise from the side and back moves or changes, it

is reduced to allow for easier listening.

WindBlock

WindBlock is designed to reduce interference caused by windy conditions and

improve comfort for listeners.

SoundRelax

SoundRelax is designed to soften sudden loud sounds, such as slamming doors or

clanking dishes.

Naída CI Q90 Sound Processor User Guide 17

EchoBlock

EchoBlock is designed to remove the disturbing reﬂections of reverberant sound

in places like large halls and places of worship.

DuoPhone

DuoPhone allows bilateral users the ability to hear phone conversations in both

ears simultaneously while also reducing surrounding noise. By placing the phone

to one ear the conversation is automatically streamed to the other ear as well,

giving the user the best possible listening experience.

ZoomControl

When you cannot face the speaker, for example, in a car, ZoomControl can

be selected to zoom to the front or the back (for both unilateral and bilateral

recipients) or to either side (for bilateral recipients) for effortless understanding.

QuickSync

QuickSync allows for easy, instant, simultaneous adjustments to volume and

program settings on two Naída CI Q90 processors so bilateral users can control

both processors with one touch.

CAUTIONS:

• UltraZoom, StereoZoom, ZoomContol, and auto

Ultrazoom will dampen sounds that are not in front of the recipient.

• Do not use UltraZoom, StereoZoom, ZoomControl, or auto

Ultrazoom in an off-the-ear wearing conﬁguration.

NOTE: StereoZoom, auto UltraZoom, SoundRelax, WindBlock, and EchoBlock are

not approved for pediatric use in the United States.

Assembling the Naída CI Q90

The Naída CI Q90 Sound Processor and accessories consists of a Naída CI Q90 sound

processor, T-Mic™ 2 microphone or earhook option, headpiece, cable, and internal implant.

The Naída CI Q90 has various sound inputs that a hearing care professional can program for

use. The Naída CI Q90 allows access to a front and rear microphone, T-Mic 2, and headpiece

microphone. It also allows for the ability to use T-coil input, wireless FM, and Roger. The Naída

CI Q90 has the ability to wirelessly stream Bluetooth® and directly connect battery-operated

devices via the ComPilot.

The processor provides you with access to the latest in sound processing technology. In addition, the

processor offers you a wide range of wearing options that can be customized to ﬁt lifestyle needs.

18 Naída CI Q90 Sound Processor User Guide

Connecting the Universal Headpiece (UHP) Color Caps

WARNING: Small Parts Hazard: The processor, UHP Color Caps, magnets, and

spacers may cause choking if swallowed.

Attaching the UHP Color Cap

Removing the UHP Color Cap

Connecting the Headpiece to the Naída CI Q90

Align the Color Cap with the headpiece. Gently press the cap and headpiece together.

The Color Cap will snap into place.

1 2

Insert the UHP Removal Tool into the slot

above the headpiece cable connector. Gently push the tool forward to release the

Color Cap as shown above.

1 2

Align the pin on the right-angled end of

the cable with the cable connection port

located below the program button on the

body of the processor.

Press in until you feel it snap into place.

1 2

Naída CI Q90 Sound Processor User Guide 19

Removing the Headpiece from the Naída CI Q90

Connecting the T-Mic 2/Earhook

Line up the pin with the hole in the T-Mic

2/Earhook and gently push it through

the hole. The pin will move from one side

of the processor, through the T-Mic 2/

Earhook, to the other, holding the T-Mic

2/Earhook in place. The pin should not

come out the other side.

If a small portion of the pin extends

beyond the processor, use the side of the

tool to push the pin inward so it lies ﬂush

with the processor.

3 4

Hold the cable’s connector (the right-angled

plastic plug, not the wire). Gently pull the cable’s connector away

from the Naída CI.

1 2

Beginning with either the earhook or

T-Mic 2 disconnected, align the T-Mic 2

or earhook ﬂush with the processor. Hold

the T-Mic 2 or earhook ﬁrmly at the top

and push towards the processor until it

meets ﬂush with the processor.

Using the provided T-Mic 2/Earhook tool,

place one of the pins in the small hole on

the side of the tool. This will help to steady

the pin as you line it up with the pin hole

on the T-Mic 2/Earhook.

1 2

20 Naída CI Q90 Sound Processor User Guide

Removing the T-Mic 2/Earhook

Pull the tool away from the processor,

leaving the pin inside the Naída CI.

Remove the power source. Align the

pointed end of the T-Mic 2/Earhook

tool with the hole on the processor that

contains the pin holding the T-Mic 2/

Earhook on the Naída CI processor.

Gently press the tool in the hole, pushing

the pin out the other side.

1 2

The pin does not need to be fully

removed from the processor. As long

as the tool was pushed in ﬂush on one

side of the processor, the pin should

be displaced enough for the T-Mic 2/

Earhook to be removed.

Remove the tool from the Naída CI.

Gently grasp the T-Mic 2/Earhook at

the top near where it connects with the

processor and pull forward, until it is

separated from the processor.

3 4

Naída CI Q90 Sound Processor User Guide 21

Attaching the T-Mic 2 Cover

Removing the T-Mic 2 Cover

Grasp the end of the T-Mic 2 where the

T-Mic 2 Cover is located, in one hand.

Firmly hold the T-Mic 2 microphone

portion in the other hand.

Turn the hand holding the T-Mic 2 Cover

counter-clockwise to slowly unscrew the

T-Mic 2 Cover from the T-Mic 2.

1 2

Hold the T-Mic 2 Cover in one hand. In

the other hand, hold the T-Mic 2 at the

end that houses the microphone. Align

the bottom of the T-Mic 2 over the

T-Mic 2 Cover.

Gently turn the T-Mic 2 Cover clockwise

into the T-Mic 2 Cover. Screw until the

parts meet together ﬂush.

1 2

Once resistance is felt, stop turning.

22 Naída CI Q90 Sound Processor User Guide

Rear View

Front View

CAUTION: It is recommended to use the T-Mic 2 only when the T-Mic 2 cover is

properly seated. The T-Mic 2 cover should be replaced every 3-4 months or if plugged

by earwax.

Wearing the Naída CI Q90

The Naída CI Q90 has been designed with ﬂexibility in mind. The processor was built to the

smallest size possible for user comfort when worn on the ear without compromising performance.

Recipients also have the option to wear the processor completely off the ear, using the clip, or

partially off the ear with the power source removed from the processor and securely attached

elsewhere on the recipient’s body. These designs ensure the most comfortable, secure, and

discreet wearing options possible. Naída CI cables come in a variety of lengths and colors

which recipients can change to suit their preference. This section describes a variety of wearing

options for the Naída CI Q90.

The Naída CI Q90 processor can be worn in a variety of locations depending on the recipient’s

age and preference. Some Naída CI wearing locations may obscure the sound processor LED;

therefore, internal alarms may be helpful to notify adult wearers of processor status. Internal

alarms can be activated by your hearing care professional.

Using the Clip

Continue turning until the T-Mic 2 Cover

separates from the T-Mic 2. Discard used

T-Mic 2 Covers.

*Enlarged view

Naída CI Q90 Sound Processor User Guide 23

Rear View

The Naída CI Clip comes in left and right conﬁgurations to provide improved wearing ﬂexibility

and the ability to wear the processor in a secure, completely off-the-ear style. This need is

particularly great for small children and many physically active CI users.

The Naída CI Clip is intended to attach directly to clothing, hair, or in a preferred wearing

location. There are both left and right sided clips to suit the recipient’s preference.

The Naída CI Clip ﬁts all ﬁve sizes of PowerCel rechargeable batteries, as well as the Zn-Air

Battery Pak. The clip also includes a silicon cover for added protection when the T-Mic 2/

Earhook is detached.

Inserting the Naída CI Q90 in the Clip

Gently, but ﬁrmly, push the processor into

the clip so the portion of the processor that

goes over the ear (ear side) slides down

into the clip. This portion of the processor

is held in place by a release tab.

If the earhook/T-Mic 2 has been

removed, secure the silicon cover

in the opening that would typically

contain the earhook/T-Mic 2.

3 4

Hold the sound processor in one hand

and the clip in the other hand. Align the processor so the button side

goes into the back of the clip opening

ﬁrst, making sure the retention arm lies

between the volume control and the

program button.

1 2

Release

Latch

24 Naída CI Q90 Sound Processor User Guide

Removing the Naída CI Q90 from the Clip

The processor should come out of the clip with the battery still attached to the processor. It is

recommended that the T-Mic 2/Earhook be removed from the Naída CI Q90 before wearing

the processor completely off the ear. Please see Removing the T-Mic 2/Earhook.

Using the Naída CI Q90 Sound Processor

Powering the Naída CI Q90

CAUTION:

Power supplies and battery chargers should be operated in an open area

to ensure adequate airﬂow. While, to date, no injuries have been reported, components

may become hot during normal use or in the event of a fault. If the device’s temperature

results in discomfort or pain when touched, disconnect the power source and contact

your local AB representative.

Depress the spring end of the clip to open

and secure the sound processor to the

desired location on clothing or in hair.

To disengage the Naída CI processor

from the clip, ﬁrst pull back the

release tab that is helping to hold the

processor in the clip.

Carefully remove the Naída CI, leading

with the internal earhook portion. Be

careful not to use the PowerCel as a lever

to remove the Naída CI; this may damage

the battery or the connector on the

Naída CI.

Naída CI Q90 Sound Processor User Guide 25

The processor is turned ‘on’ when a charged battery is attached to the processor. In order to

power ‘off’ the processor, the battery cartridge must be removed. When the battery is engaged

the orange LED located in the middle of the volume control will ﬂash to indicate battery charge

followed by the green LED to indicate program position.

The Naída CI Q90 will always power on in Program 1 with the volume and sensitivity at the default

settings.

To power down the Naída CI Q90, simply remove the battery cartridge.

Removing the Battery

Hold the sound processor in one hand. In

the other hand hold the battery cartridge.

Rotate the RF cable upward to avoid

bumping it upon battery removal.

2 1

Firmly slide the battery cartridge away

from the Earhook or T-Mic 2. Continue sliding the battery cartridge until

it separates from the processor.

3 4

26 Naída CI Q90 Sound Processor User Guide

Replacing the Battery

NOTE: Do not force the battery cartridge onto the processor. The battery cartridges are

designed to be inserted in only one direction; applying force may damage the equipment.

Hold the Naída CI in one hand. Rotate

the RF cable upward to avoid bumping it

upon battery placement.

Align the battery cartridge connector

with the processor housing side of

the connector.

1 2

Slide the battery onto the processor

until it clicks into place.

Naída CI Q90 Sound Processor User Guide 27

Understanding Naída CI LEDs

The Naída CI LEDs are a programmable feature providing visual information about the Naída

CI Q90 status, battery life, program position, and error conditions.

Naída CI Q90 Sound Processor LED Indications

NOTE: Use of some Naída CI accessories may obscure the processor LED.

Color Behavior Programmable Indication

Orange Blinks at start-up No. Battery indicator is

only available with use

of the rechargeable

PowerCels and AAA

PowerPak. Battery life

indicators are not

available with use of

Zn-Air batteries.

• 4 quick blinks indicate that the

battery is fully charged

• 2 - 3 quick blinks indicate that the

battery is sufﬁciently charged to

power the Naída CI Q90

•1quick blink indicates that the

battery is nearly depleted

• No blinking indicates depleted

battery. Replace with charged or

new battery

Solid Ye s The battery is almost depleted

Blinks twice every

three seconds Yes The battery is almost depleted

and cannot support stimulation

(Sleep Mode)

Fades out No The Naída CI Q90 is entering Sleep

Mode

Red Blinks once

per second Yes Loss of lock with the implant

Blinks rapidly (more

than once per

second)

No Intellilink™ enabled and the Naída

CI Q90 is connected to the wrong

implant

Solid No Sound processor error condition. Fully

remove and re-insert the battery to

reset processor

Green Flickers in response

to loud inputs Yes The sound processor and microphone

are responding to sound

Blinks at start-up,

after battery

status, and upon

program change

No • 1 blink indicates program one

• 2 blinks indicate program two

• 3 blinks indicate program three

• 4 blinks indicate program four

• 5 blinks indicate program ﬁve

Solid Green No A processor that is not yet programmed

Blinks 4 times No-if using AB myPilot

this pattern is the default Response to AB myPilot’s request to ‘Find

Paired Devices’. The Left paired device will

identify itself with this LED pattern.

Blinks 5 times No-if using AB myPilot

this pattern is the default Response to AB myPilot’s request to

‘Find Paired Devices’. The Right paired

device will identify itself with this LED

pattern.

28 Naída CI Q90 Sound Processor User Guide

If the user would like to know the battery status of the Zn-Air Battery Pak they are currently

using and have an AB myPilot paired to their device, they can conduct a Battery Check readout

of the Naída CI Q90. To ensure an accurate reading of the Zn-Air Battery Pak, wait at least 15

minutes after it has been attached to the Naída CI Q90 before performing a Battery Check

readout.

Please see the Battery Check section of the AB myPilot User Guide for instructions on how to

conduct a battery status check using AB myPilot.

Understanding Internal Alarms

Internal alarms are a programmable feature that can be used independently or in conjunction

with the Naída CI LEDs to provide important information about Naída CI status and battery life.

Naída CI Internal Alarms

Using the Naída CI Headpieces:

The Naída CI Q90 works with the Universal Headpiece (UHP)

The Universal Headpiece

The UHP is designed for use with the Naída CI Q90 processor during all daily activities, with the

exception of swimming and bathing.

Replacing RF Cables

RF cables are available in a variety of colors and lengths to suit the recipient’s personal wearing

preferences. Before you can use the Naída CI Q90 sound processor, you must use the cable

Behavior Programmable Indication

Beeps upon

program change Ye s • 1 beep indicates program one

• 2 beeps indicate program two

• 3 beeps indicate program three

• 4 beeps indicate program four

• 5 beeps indicate program ﬁve

Short Beep upon

increase/decrease

in volume

Yes Beeps once per press of the volume control

either up or down (a double beep will be heard

when the following settings are reached: top of

the volume range; baseline volume setting; and

bottom of the volume range)

Long Beep (once

every 15 minutes) Ye s Low battery

Naída CI Q90 Sound Processor User Guide 29

to connect it to the headpiece. Inspect the cable on a regular basis to ensure it is in good

condition. If it appears damaged, replace it with a new cable.

To attach the cable to the headpiece:

To attach the cable to the sound processor:

For assistance in troubleshooting headpiece cables, please refer to the Troubleshooting section

of the User Guide.

Adjusting Headpiece Magnet Strength

It is important to have the correct magnet strength so the recipient does not experience

discomfort or retention issues. If an insufﬁcient number of magnets are used in the headpiece,

it may fall off more often than is acceptable. If too many magnets are used , the recipient may

experience irritation or discomfort. Consult a hearing care professional if you have any concerns

regarding magnet strength. If deemed appropriate, your hearing care professional may insert

additional magnets or remove magnets from the headpiece. If the recipient experiences any

redness, irritation, or discomfort, discontinue use of the headpiece immediately and contact

a cochlear implant center. See the Headpiece Instructions for Use for additional information

Hold the headpiece in one hand and the

cable connector in the other hand. Push the cable connector ﬁrmly into the

headpiece connector.

1 2

Hold the sound processor in one hand and

the cable connector in the other hand. Push the cable connector ﬁrmly into the

sound processor connector port.

1 2

30 Naída CI Q90 Sound Processor User Guide

Program Button

regarding adjustment of headpiece magnet strength.

WARNING:

Do not place additional magnets in the headpiece unless under the

direction of a cochlear hearing care professional.

Removing Headpiece Color Caps

The UHP Color Caps are available in a variety of colors to match or coordinate with the Naída

CI sound processor. A Color Cap must be in place at all times when using the headpiece.

Color Caps can be replaced to change the look and style of the headpiece. To remove the

headpiece Color Cap, only use the tool provided by Advanced Bionics. See the Color Cap or

UHP Instructions for Use or the Connecting Universal Headpiece (UHP) of this User Guide for

additional information regarding removal and replacement of headpiece Color Caps.

Adjusting Controls on the Naída CI Q90

Changing Programs

The program button is located on the spine of the Naída CI to allow the recipient to easily

change the listening program during use. The Naída CI can store up to ﬁve programs for

optimal listening in a variety of situations. These programs can be updated and changed by

the hearing care professional during ﬁtting.

Any changes made to volume or sensitivity will be carried over to subsequent program changes.

This applies to volume changes with either onboard volume controls or the AB myPilot remote

control, as well as to sensitivity changes made with the AB myPilot remote control.

To change programs:

Push the program button down brieﬂy and then release the button. Through the push of the

button the programs will switch in a chronological order; after the ﬁnal program, the user will

return back to the ﬁrst program.

Naída CI Q90 Sound Processor User Guide 31

Volume Control

Decrease

Increase

Additional Functionality of the Program Button:

The Program Button also allows the user to enter or exit Standby Mode. Standby Mode is a

low power state the Naída CI Q90 can enter to save power without having to be turned off.

Standby mode allows the PowerCel or Zn-Air Battery Pak to remain attached to the processor

without causing a major drain on battery life. For example, if a user on a long ﬂight wants to

leave the device on his ear but turn off the sound, he can actively put the device in Standby

Mode to conserve power. The beneﬁt of this feature is that the user can quickly resume use of

the device and not worry about draining his battery. Standby mode can be enabled or disabled

by a hearing care professional in the SoundWave™ ﬁtting software.

Actively Entering Standby Mode:

• The user must hold down the program button for four seconds.

• Upon entering Standby Mode, an orange LED will brieﬂy light up before fading out. This

indicates the processor has entered Standby Mode.

NOTE:

LEDs will not light up during Standby Mode.

Passively Entering Standby Mode:

The device will also enter Standby Mode passively if left unlocked for more than ﬁve minutes.

Exiting Standby Mode:

• To exit Standby mode the user simply presses the program button brieﬂy once.

• An orange LED will light up on the device to indicate battery status followed by a blinking green

LED to indicate the current program setting. The device is now fully powered and ready for use.

Changing Volume

The volume control is located on the spine of the Naída CI Q90, just above the program button.

If the hearing care professional has not disabled the volume control, 10 presses on the top

portion of the volume control will take the recipient to maximum volume output, while 10

presses on the bottom portion of the volume control from the baseline volume position will take

the recipient to the minimum volume output. The Naída CI Q90 processor’s LED is located in

the middle of the volume control.

32 Naída CI Q90 Sound Processor User Guide

To change volume:

The volume range available within a program can be changed or disabled by a hearing care

professional in the SoundWave™ ﬁtting software. If there are any questions about the speciﬁc

volume range setting, please contact an implant center.

REMEMBER: The QuickSync feature allows bilateral wearers to control program

and volume in both devices simultaneously by only touching one Naída CI Q90.

Changing Sensitivity

A change in sensitivity adjusts the softest sound that can be picked up by the microphone. Sensitivity

adjustments are either programmed by a hearing care professional in the SoundWave™ ﬁtting

software or through the use of the AB myPilot remote control. If you have any questions about

the speciﬁc sensitivity control settings, please contact an implant center. Please see Changing

Sensitivity with the AB myPilot Remote Control in the AB myPilot User Guide.

Connectivity

Using FM/Roger

The FM and Roger features help many cochlear implant users, particularly school-aged children,

overcome difﬁculties hearing a speaker at distance in the presence of noise and reverberation.

The Naída CI Q90 sound processor enables use of wireless FM and Roger systems through

three different modes.

The ﬁrst way to access FM/Roger is by attaching the FM or Roger receiver directly onto the

ComPilot streamer. The signal is then transmitted wirelessly to the Naída CI Q90. This signal can

be transmitted to one or two Naída CI Q90 processors for bilateral recipients. FM/Roger signals

can also be streamed to a Naída CI Q90 and a Phonak Hearing Instrument simultaneously for

bimodal users.

Pressing brieﬂy on the top portion of the

volume control will increase the volume.

Pressing brieﬂy on the bottom

portion of the volume control will

decrease the volume.

1 2

Naída CI Q90 Sound Processor User Guide 33

ComPilot

MLxi

MyLink

The second method to access FM/Roger is by having a hearing care professional activate the

telecoil. The telecoil, used in conjunction with a looped room, Phonak Roger MyLink, or the

Phonak MyLink, will allow the recipient to hear the speaker without the use of connecting wires.

Please see ComPilot User Guide or AB addendum for ComPilot for more information.

The third method to access Roger is by attaching the Roger 17 design integrated receiver

directly to the underside of the PowerCel 170 battery.

NOTE:

Front End Processing features will be disabled when the Roger 17 module

is attached to the PowerCel 170 battery.

NOTE: To avoid any unpleasant sounds, ensure that the sound processor is turned

off before attaching or removing an FM/Roger receiver. Read the operating instructions

provided with the FM/Roger system prior to using FM/Roger with the Naída CI Q90

processor.

34 Naída CI Q90 Sound Processor User Guide

To attach an FM/Roger Receiver to the ComPilot:

Adjust the program position on the processor or AB myPilot to the desired program for

FM/Roger use.

Reduce volume settings.

Turn on the ComPilot.

Adjust the volume to the desired level for FM use.

To remove an FM/Roger receiver:

Readjust the program position and volume to their desired settings for non-FM/Roger use.

For further information regarding FM/Roger use, refer to the Instructions for Use included with the

FM/Roger system.

With the ComPilot turned off, hold the

ComPilot in one hand. With the other hand,

align the three connector pins with the

Europort on the ComPilot. Take care to ensure

that the FM/Roger receiver pins match the

size and orientation of the holes on the

ComPilot. Failure to do so may cause damage

to the FM/Roger receiver and/or the ComPilot.

Firmly press the FM/Roger receiver

into place on the ComPilot.

1 2

With the ComPilot turned off, hold the

ComPilot in one hand. With the other hand, gently pull the FM/

Roger receiver straight out of the Europort.

1 2

Naída CI Q90 Sound Processor User Guide 35

Pairing to the AB myPilot

In order for the AB myPilot to control the Naída CI(s), it must be paired to the processor/s. The

AB myPilot may be un-paired and paired to multiple Naída CI processors. This allows one AB

myPilot to be used with all Naída CI recipients in a classroom. This may also be convenient for a

caregiver with several implanted children. They would only need one AB myPilot to have remote

control access to everyone.

The AB myPilot must be paired to your Naída CI Q90 within ﬁve minutes of the processor

starting up. This time period is referred to as the Pairing Window and it begins upon the

attachment of the PowerCel or Zn-Air Battery Pak or Power Adapter to the Naída CI Q90.

After the ﬁve minute Pairing Window ends, pairing is no longer possible. If you need more time

to pair, you must remove and replace the Naída CI battery to begin the Pairing Window again.

Sound input to the processor is not affected during this period. If pairing is not desired, the user

can proceed with normal use of the Naída CI Q90 during this time.

To Begin Pairing the AB myPilot to the Naída CI Q90:

Make sure a hearing care professional has enabled remote control functionality on the

Naída CI Q90.

Have the Naída CI Q90 you want to pair within 11 inches (30 cm) of the AB myPilot remote

control.

Attach a PowerCel or Zn-Air Battery Pak to the Naída CI Q90, commencing the Pairing

Window (ﬁve minute time out).

Upon turning on the AB myPilot will read the

following, ‘The AB myPilot needs to be paired

with your hearing instruments.’ Press the

center button on the remote control.

The main menu will be shown; from this

menu, click the downward arrow button

to highlight the Pairing option. Press the

center button again to select.

4 5

36 Naída CI Q90 Sound Processor User Guide

On the AB myPilot you can press the center button to return to the Home screen.

To un-pair the AB myPilot and Naída CI Q90:

If you wish to un-pair only one of the Naída CIs that you currently have paired, highlight

the Pair Devices option and press the center button.

From this menu press the downward

arrow button to highlight the Scan for

Devices option.

When the Naída CI Q90 is found, it will

show the recipient’s initials on the AB

myPilot, as well as the ear it is primarily

programmed for.

6 7

There will be a green circle with a

checkmark in it to show that it is paired.

Using the AB myPilot remote control,

press the center button to be taken to

the Main Menu. from this menu, click the

downward arrow button to highlight the

Setting option. Press the center button

again to select.

From the next menu that is shown, use

the downward arrow to highlight the

Pairing option and press the center

button again to select.

1 2

Naída CI Q90 Sound Processor User Guide 37

The screen will tell you which devices are paired by showing a green circle with a checkmark

in it beside the recipient’s initials. Move to highlight the device you would like to un-pair using

the downward arrow. Press the center button once you have highlighted the device.

The green circle with the checkmark will disappear, and the device will be un-paired and

will no longer be controlled by the AB myPilot remote.

CAUTION: Be advised that placing the AB myPilot within a 0.4 inch (1cm) range

of the Naída CI Q90 will cause the Naída CI Q90 to lose communication with

accessory devices such as the AB myPilot and/or the ComPilot. At this time,

the AB myPilot will not be able to communicate with the Naída CI Q90. The

Naída CI Q90 will have to be power cycled (restarted by removing and replacing

the power source) in order for the AB myPilot to resume communication with the

sound processor.

The AB myPilot is intended to work at an arm’s length from the Naída CI Q90.

If you wish to un-pair all devices at

once, from the pairing menu, press the

downward arrow button to highlight the

Clear Pairing option. Press the center

button to select.

The device will then ask you to conﬁrm this

command. You can conﬁrm it by selecting

Conﬁrm and pressing the center button.

6 7

Pressing the center button will clear

pairing for all Naída CIs that are paired

to the AB myPilot.

38 Naída CI Q90 Sound Processor User Guide

Front Mic Rear Mic

Headpiece Mic

T-Mic 2

Remove the battery from the processor

(if not already removed). Hold the

Naída CI Listening Check with one

hand using the grip indents on the

sides for traction. Using the other hand,

grasp the Naída CI Listening Check

over the AB logo and pull out.

Turn the AB logo portion of the Naída CI

Listening Check 90 degrees.

1 2

The Naída CI Listening Check and Listening Check Earbuds

Listening to the Microphone(s) and Auxiliary Inputs

A convenient test mode is built in to all Naída CI processors to enable individuals with unaided

hearing to listen to sound sources. With the AB myPilot Remote Control, all sound sources

can be listened to independently. Without the AB myPilot Remote Control, sound sources are

listened to on a program-by-program conﬁguration.

The available sound sources are:

• Microphones (Front and Rear, Head Piece, T-Mic 2)

• FM/Roger receivers

• T-coil

• Sound being streamed through the ComPilot

To listen to the desired input:

Naída CI Q90 Sound Processor User Guide 39

Connect the bottom of the Naída CI

Listening Check to the power source

(PowerCel, Zn-Air Battery Pak, AAA

PowerPak).

Connect the supplied earbuds to the

3.5 mm auxiliary jack on the side of

the Naída CI Listening Check.

5 6

Place the earbuds in the ears of the unaided listener.

When the Naída CI Listening Check is attached, the processor immediately enters listening check

mode. If you are not using an AB myPilot to select the input sound source, you will be listening to the

input sound source conﬁguration of the ﬁrst program. If you would like to listen to the other

program sound source conﬁgurations, use the program button to cycle through the programs.

If you are using an AB myPilot, select Listening Check from the AB myPilot menu and

select the input sound source to which you would like to listen. Alternatively, if the Naída CI is

already connected to the Naída CI Listening Check and paired to the AB myPilot, the AB myPilot

will go to the Listening Check screen once it communicates with the Naída CI. This can be done

by brieﬂy pressing the power button on the AB myPilot. Once the Listening Check screen is shown,

you can use the left and right arrows to listen to program conﬁgurations and the sound

sources independently.

a. If you select T-coil, make sure you are synced to a loop, myLink, or Roger myLink. Provide

Insert the AB logo portion into the other

portion of the Naída CI Listening Check.

You should feel the two portions snap into

place. Once in place, the processor and

battery connectors will be exposed.

Connect the top of the Naída CI

Listening Check Module to the processor

3 4

40 Naída CI Q90 Sound Processor User Guide

input to the FM transmitter or Roger Microphone to assess audio quality.

b. If you select Wireless, you will be listening to whatever audio source is being streamed

through the ComPilot (i.e. Bluetooth device, FM/Roger, battery-operated device, etc.).

To begin the process, have the ComPilot turned on and the desired source streaming. It

is a good idea to turn the volume down on any device that is directly connected to the

ComPilot. If listening to FM/Roger input, connect the wireless FM/Roger receiver to the

Europort located on the ComPilot or to the PowerCel 170 battery and synchronize it with

the FM transmitter or Roger Microphone. Provide input to the FM transmitter or Roger

Microphone to assess audio quality.

To close the Naída CI Listening Check when

not in use, remove the earbuds and grasp

the grip indents on the side of the Naída

CI Listening Check with one hand while

grasping the processor and battery interfaces

with the other hand. Carefully pull your

hands apart until the two pieces disconnect.

Turn one piece 90 degrees, aligning the

AB logo piece to slide into the other piece.

12 13

Once the listening check is complete,

disconnect the module from the battery. Remove the processor from the module.

Reconnect the battery to the processor,

and select the desired settings for use.

10 11

Naída CI Q90 Sound Processor User Guide 41

NOTE: The Naída CI Listening Check requires a charged power source to function

correctly. If the power source being used to conduct the listening check has been

depleted to an inadequate charge level, the user will not be able to complete the task.

If the user attaches a discharged rechargeable PowerCel, AAA PowerPak or Off-the-Ear Power

Option, a solid red LED will light up on the Naída CI Q90.

If the user attaches depleted Zn-Air batteries, the sleep mode LEDs will be shown on the

Naída CI Q90 (orange LED blinks twice every three seconds) or, if the cartridge is completely

discharged, no LEDs will be shown and no sound will be heard through the Listening Check

earbuds.

Using the Telephone

There are a variety of ways to use the telephone with the Naída CI Q90 sound processor.

Consult a hearing care professional for recommendations regarding telephone use and which

of the following options are best:

• Use the telephone receiver. The telephone can be used by placing the telephone receiver

directly over the T-Mic 2, processor microphones or headpiece microphone, if activated. It is

sometimes necessary to try different phones and providers, particularly when cellular phones

are used, in order to ﬁnd the optimal telephone signal.

• Use T-coil. The T-coil is programmable by a hearing care professional in the SoundWave™

ﬁtting software. If there are any questions about whether it is activated and in what program,

please contact the implant center. When using the T-coil it may be necessary to move the

phone receiver around the Naída CI Q90 to see where it works best.

• Use Bluetooth®. Any Bluetooth compatible device can be synced to the ComPilot to stream

phone calls directly to the Naída CI Q90. The microphone for the speaker is located on the

ComPilot, so the phone can be up to 15 - 30 feet (5 - 10 meters) away and still be in use.

• Use DuoPhone (for bilateral recipients). DuoPhone is programmable by your hearing care

Push them together until they snap into place.

42 Naída CI Q90 Sound Processor User Guide

professional in the SoundWave ﬁtting software. With the phone placed to one ear, the conversation

is heard in both ears.

• Use a patch cable. A patch cable may be used to connect directly to a cellular or cordless

phone. The patch cable connects to the headset jack of the phone on one end and

the auxiliary jack of the ComPilot on the other. An Audio Interface Cable is available from

AB, or a custom-made patch cable from an independent vendor may be required. Consult

with a hearing care professional or an AB representative for further information regarding

this option.

• Use a speaker phone. Using a speaker phone eliminates the need for additional equipment

when using the telephone. Simply turn on the speaker phone and communicate in your

regular manner.

Telephone Tips

• Be patient. Remember that phone use takes practice and will improve over time.

• Practice listening with familiar speakers, such as family members, friends, your therapist, or

hearing care professional.

• It may be helpful to become familiar with the topic of discussion ahead of time. For example,

tell your friend to call you at a speciﬁc time to talk about a speciﬁc topic (e.g., Call me at 6:00

p.m. to talk about going to the movies).

• You may need to practice with several telephones to ﬁnd one that is right.

• When selecting a cellular phone, remember to try the phone ﬁrst.

• For additional telephone support and listening exercises, visit TheListeningRoom.com.

Telecoil

Using the Built-in Telecoil

Telecoils provide wireless access to hearing-aid-compatible telephones and induction-loop

systems (found in some public facilities). Telecoils capture electromagnetic ﬁelds in the

environment and deliver these signals to your processor. A telecoil is built into your processor

and is programmed by a hearing care professional. To activate your telecoil, ﬁrst consult with

the hearing care professional to determine if a program in your processor has been created for

its use. If so, the telecoil will activate once the processor is switched to the designated program.

For your telecoil to be effective, the recipient must have access to a looped system or a hearing

aid-compatible phone. This will allow the telecoil to receive the electromagnetic ﬁeld generated

by these devices. If the recipient is attempting to use the telecoil with a non-compatible audio

device, no sound or a low-level humming or buzzing noise may be heard.

Naída CI Q90 Sound Processor User Guide 43

CAUTION: Telecoils are known to be susceptible to magnetic noise generated by

most industrial lighting ﬁxtures, store and airport security scanners, band scanners,

power transformers, motor starters, and monitor screens.

Battery Information

The Naída CI Q90 sound processor can be used with two disposable Zn-Air batteries, ﬁve sizes

of rechargeable Lithium Ion PowerCels, the AAA PowerPak, or the Power Adapter. Please refer to

the AAA PowerPak and Power Adapter Instructions For Use for more details on these products.

PowerCel 230

PowerCel 170 Mini Zn-Air (Tamperproof Cartridge)

PowerCel 170

Zn-Air

AAA PowerPak

Power Adapter

PowerCel 110 Mini

PowerCel 110

44 Naída CI Q90 Sound Processor User Guide

Battery Charger

USB

Power Supply

Power Supply Adapters

WARNING: Do not connect the Zn-Air Battery Pak to the charger. The charger is

to be used with the rechargeable Lithium Ion PowerCels only. All four sizes of Lithium

Ion PowerCels can be used on the PowerCel Charger.

Assembling the PowerCel Charger

WARNING:

Power supplies and battery chargers should be operated in an open area to

ensure adequate airﬂow. While, to date, no injuries have been reported, during normal

use in the event of a fault, components may become hot. If the device’s temperature

results in discomfort or pain when touched, disconnect the power source and contact AB.

CAUTION: Only use the charger provided for charging AB PowerCels. Do not use it

to charge other batteries. Do not try to charge Naída CI PowerCels using a charger

other than that provided by Advanced Bionics.

The charging system consists of the charger, power supply, and power supply adapters. The

charger can also be used with the power supply removed from the cable, exposing the USB jack

so it can be powered from any USB port.

Charging Information for Lithium Ion Batteries:

The charger provided with the sound processor is designed to charge up to four PowerCels

simultaneously. It takes approximately 2-3 hours to fully charge a depleted PowerCel. This will

vary slightly for different PowerCel types.

Naída CI Q90 Sound Processor User Guide 45

Gently slide the PowerCel out of the

slide tracks of the charger, sliding

toward the outer edge of the charger.

Locate the slide tracks on the charger.

Position the PowerCel so that the

battery contact is facing down toward

the base of the charger.

Slide the PowerCel along the tracks

until it engages. The charger is

designed so the PowerCels can only be

inserted in one direction.

1 2

The PowerCels do not need to be fully depleted before recharging.

It is recommended that you use and recharge the PowerCel(s) at least once every three months.

Please note that PowerCels will decrease in capacity with age, even if not in use. This is normal

for all rechargeable batteries and should not be considered a defect.

NOTE FOR EUROPEAN CUSTOMERS: For proper disposal of rechargeable batteries in

Europe, please return depleted batteries to the nearest AB representative or a designated

programming/follow-up center.

In the United States and Canada, please call the Rechargeable Battery Recycling Corporation

hotline at 877.273.2925 or visit their website at www.call2recycle.org.

Inserting the PowerCels into the Charger

Removing the PowerCels from the Charger

46 Naída CI Q90 Sound Processor User Guide

The Zn-Air Battery Pak

The Naída CI Q90 uses size 675 Power Implant disposable batteries (675P). Regular size

675 hearing instrument batteries will not be powerful enough for a cochlear implant.

Inserting Zn-Air Batteries

Remove the Zn-Air batteries from their package, making sure to remove the tape from the ﬂat

positive (+) side of the cell. Removing the tape allows oxygen to ﬂow in and activate the battery,

so be sure to install it immediately after peeling off the tape.

Note: If the cells are inserted incorrectly, the battery drawer will not close.

Place two Zn-Air batteries, positive (+)

(ﬂat) side up, in the two openings in the

battery drawer.

Once the batteries are ﬂush with

the top of the battery drawer, gently

slide the battery drawer back into the

battery cartridge.

4 5

Holding the Zn-Air Battery Pak in one hand,

gently but ﬁrmly push down on the lever on

the back of the battery cartridge. This will

cause the drawer to pop out of the bottom

of the cartridge.

Pull the battery drawer out of the

cartridge with the other hand.

1 2

Naída CI Q90 Sound Processor User Guide 47

Use the same tool provided for T-Mic 2/

Earhook removal and replacement—Insert

the pointed end of the tool into the small

hole located on the spine of the Zn-Air

Battery Pak. Note: If you do not have the

tool present, any thin pointed device should

work to release the drawer.

With the tool inserted in the hole, gently

push in and downward until you feel

the Zn-Air Battery Pak drawer release

and the button of the Zn-Air Battery

Pak pops out.

1 2

Set the tool aside and grasp the Zn-Air

Battery Pak drawer with your hand and

gently pull it the rest of the way out.

Attach the battery cartridge to the Naída CI following the same instructions as attaching the

PowerCels to the Naída CI in the section Replacing the Battery.

Inserting Zn-Air Batteries (Tamperproof Cartridge)

To insert the batteries, follow instructions Step 2 to 5 of the previous section Inserting Zn-Air Batteries.

48 Naída CI Q90 Sound Processor User Guide

Charger LED (Light Emitting Diode) Indicator

The charger has different indicator lights that are located at the base of each PowerCel charging

port as well as where the power cable enters the charger. If the green micro USB light is lit, it

means the charger is connected to a power source and ready to charge the PowerCels.

The LEDs located at the base of each PowerCel charging port have 3 color options.

Understanding PowerCel Charging Port LEDs

If a fault is exhibited by the PowerCel charger, ﬁnd out if the fault is with the PowerCel or the

charger itself by doing the following. Insert a different PowerCel in the charger bay that exhibits

the problem. If the red LED is still on, there is a problem with the charger. If the red LED does

not light up, there is a problem with the PowerCel. If there is a problem with either the PowerCel

or the charger, please contact Advanced Bionics.

The charger LED turns off (or may show a faint blue if the room is very dark to indicate either

the battery is fully charged or there is a fault with the battery. The user should wait one full

minute. If the LED turns green, the battery is fully charged and ready for use. If the LED does not

turn green after one minute, the battery should be considered faulty and you should contact

Advanced Bionics for a replacement.

Color Indication

Blue PowerCel is charging

Green PowerCel is fully charged

Red Fault Condition

LED Port Lights

LED Micro USB Light

Naída CI Q90 Sound Processor User Guide 49

WARNINGS:

• Do not recharge disposable batteries.

• Do not place batteries in mouth.

• Do not chew or swallow batteries. If this happens, seek immediate medical attention.

• Do not allow leaking battery ﬂuid to come into contact with skin, mouth, or eyes.

• Do not dispose of batteries in a ﬁre.

• Do not leave children unattended with or allow them to play with batteries.

• Do not allow children to charge batteries unattended.

CAUTIONS:

• Remove batteries from the sound processor when they are drained to prevent

damage from possible leaking.

• If a battery shows visible signs of leakage, dispose of it in accordance with local regulations.

• Do not expose batteries to heat (e.g., do not store in direct sunlight or in a hot car).

• Carry batteries in the carrying case provided or in a sealed plastic bag. Batteries can

short circuit if they come into contact with metallic objects such as coins or keys.

• Do not immerse batteries in water.

• Only charge batteries using the charger(s) recommended by the manufacturer.

• When Roger is not attached, use clear cover provided to protect pins.

For additional information, refer to the Approved Power Sources section of the User Guide.

Using Naída CI Accessories

Advanced Bionics supplies a range of accessories for use with the Naída CI Q90, although not

all accessories may be included in the sound processor kit. Discuss with the recipient’s hearing

care professional which accessories are included with the Naída CI Q90 sound processor.

For further information regarding the accessories listed below, refer to the Instructions for Use

included with the product or contact Advanced Bionics.

50 Naída CI Q90 Sound Processor User Guide

ComPilot

MLxi

Universal Headpiece (UHP)

Naída CI Listening Check

Listening Check Earbuds

Headpieces

The Naída CI Q90 sound processor is designed for use with the Universal Headpiece (UHP).

The UHP is intended to be used with the Naída CI Q90 during daily activities outside of water

environments.

ComPilot

When used with the ComPilot, the Naída CI Q90 is compatible with the Phonak MLxi and

Roger X wireless receivers. For instructions on how to connect a receiver to the ComPilot, refer

to the Using FM or Roger section of the User Guide or to the ComPilot Instructions for Use and

AB ComPilot Addendum.

Naída CI Listening Check and Listening Check Earbuds

Naída CI Q90 Sound Processor User Guide 51

Naída CI Listening Check

Audio Input

(3.5 mm Auxiliary Jack)

FM/Roger Input (Euro Socket)

Charging Input (Mini-USB)

ComPilot

The Naída CI Q90 has a convenient monitor mode, accessed by using the Naída CI Listening

Check and Listening Check Earbuds. This mode enables someone with unaided hearing to

listen to the Naída CI Q90 input sound sources. For instructions on how to listen to inputs using

the Naída CI Listening Check and Listening Check Earphones, refer to the Listening to the

Microphone(s) and Auxiliary Inputs section of the User Guide.

Audio Accessories

The auxiliary jack on the ComPilot allows the recipient to plug directly into battery-operated

consumer electronics devices, such as MP3 players, portable DVD players, or handheld

gaming devices. When connecting to consumer devices, it may require attenuation to prevent

sound from being too loud or distorted. This attenuation can be applied by a hearing care

professional during programming so the recipient can fully enjoy the sound from an audio

device. Also, a hearing care professional can create a program allowing the recipient to hear

both environmental and auxiliary device sounds. Talk to your hearing care professional about

which programming options are right for the recipient in this situation.

WARNINGS AND CAUTIONS:

• Do not connect to mains powered sound sources (e.g. TV, computer) unless

using a mains isolation cable.

• Do not swim or bathe with the ComPilot.

• NOTE: When streaming audio with the ComPilot, if your headpiece becomes

unlocked, turn off the ComPilot prior to re-locking your headpiece. Not doing so

may prevent the sound processor from communicating with your implant.

Color Customization

The Naída CI Q90 comes in a variety of color options, allowing the recipient to customize the

look of the sound processor to suit their personal style.

52 Naída CI Q90 Sound Processor User Guide

Naída CI Carrying Case

A carrying case is provided with the Naída CI Q90 for use when traveling or for storage when

the sound processor and accessories are not in use. If the Naída CI Q90 is exposed to moisture

or high levels of humidity, store components overnight in the drying system provided.

Drying System

A drying system is included with the Naída CI Q90. It is designed to remove moisture from the

equipment and is intended for daily use with the Naída CI accessories. For detailed instructions

on how to use and care for the drying system, refer to the Operating Instructions included in

the package. It is important that you read and adhere to the Warnings and Cautions prior to

and during use.

Naída CI Carrying Case

Naída CI Q90 Sound Processor User Guide 53

IP Rating Information

An ingress protection, or IP, rating is used to specify the strength of an enclosure surrounding

electronic equipment. Each IP rating consists of two numbers. The ﬁrst number indicates the

level of protection an enclosure provides against intrusion by solid objects, materials, or dust.

The second number indicates the level of protection against intrusion by water or liquids.

The Naída CI Q90 carries a rating of IP57. This rating indicates that the Naída CI Q90 is

protected against the following conditions:

• Penetration of solid foreign objects equal to or greater than 1.0 mm in diameter

• Failure due to immersion for 30 minutes to a depth up to 1m.

Care of the Naída CI Q90 Sound Processor and Accessories

It is important to properly care for the Naída CI Q90 to ensure optimal hearing at all times. If

any part of the Naída CI Q90 needs to be cleaned, use only a damp cloth to wipe the part(s).

Do not expose any part of the sound processor or accessories to additional solvents (e.g. soap,

bleach).

Changing Microphone Covers

The Naída CI Q90 has a microphone ﬁlter located over the rear microphone to prevent dust

and debris from damaging the microphone. Advanced Bionics recommends changing the

microphone cover on the Naída CI Q90 every three months, or earlier if there is a notice in the

degradation of sound quality.

Removing the Microphone Cover

Grasp the Naída CI Q90 in one hand while

holding the removal tool in the other hand. Using the end of the tool with the

threads on it, screw into and through the

microphone cover until the tool is capable

of removing the microphone cover.

1 2

54 Naída CI Q90 Sound Processor User Guide

Replacing the Microphone Cover

Carefully pull the tool out of the opening.

The microphone cover should come out

with the tool. The cover can be removed

from the tool and then disposed of.

Grasping the tool in one hand, use the blunt,

non-threaded end to put a new microphone

cover on the end of the tool. The microphone

cover is quite small, so the tool works as a

guide to properly and easily replace the cover.

With the microphone cover on the end

of the tool, hold the Naída CI Q90

in the other hand and carefully align

the end of the tool directly over the

opening to the microphone.

1 2

Press the cover into the hole until the tool is

ﬂush with the processor. Carefully pull the tool away from the

processor, leaving the microphone cover

correctly seated in the microphone port.

3 4

Naída CI Q90 Sound Processor User Guide 55

Recommended Naída CI Q90 Operating and Storage Temperatures

Operating and Storage Temperature Ranges

Approved Power Sources

Advanced Bionics has veriﬁed the Naída CI Q90 to function with the power sources listed

below; behavior when using power sources other than those listed here cannot be guaranteed.

Approved Naída CI Q90 Power Sources

Power Source Capacity (mAhr)

PowerCel

110

170

230

PowerCel Mini 110

170

Zn-Air 1,140

Programming Interface

(used during ﬁtting, only) Not Applicable

Approved Naída CI Q90 Power Supplies

Troubleshooting the Naída CI Q90

If no sound is heard or the red LED is ﬂashing once per second on the Naída CI Q90 processor

LED when the headpiece is in place over the implant, try the following troubleshooting steps:

Visually inspect the cable for any damage or breakage and verify it is ﬁrmly attached to

the headpiece and sound processor.

Remove any materials (hat, scarf, headband, etc.) that may be covering the microphone.

Unaided listeners may perform a listening check of the microphones as described in the

Listening to the Microphone and Auxiliary Input section of the User Guide.

Power Supply Rated Voltage Type

PowerCel

Zn-Air

Rated Energy

Programming Interface 5.0 V 1,250 mWDC

Condition Minimum Maximum

Operating temperature 0°C (32°F) 45°C (115°F)

Storage temperature -20°C (-4°F) 55°C (131°F)

2.8 V

3.7 V Li-ion (Rechargeable) 0.4 Wh – 0.9 Wh

Zn-Air (Disposable) 1,240 mWh

56 Naída CI Q90 Sound Processor User Guide

Replace the cable.

Replace the headpiece.

If these measures do not resolve the problem, contact a hearing care professional or Advanced Bionics

immediately for further assistance.

If no sound is heard or a solid red LED is indicated on the Naída CI Q90 processor LED, try the

following troubleshooting steps:

Remove the battery cartridge.

Reattach the battery cartridge.

If you are using Zn-Air batteries and steps 1 and 2 do not resolve the problem, replace

with fresh Zn-Air batteries and reattach the battery cartridge.

If you are using PowerCels, try a PowerCel with a known full charge and reattach.

If these measures do not resolve the problem, contact a hearing care professional or Advanced

Bionics immediately for further assistance.

If static or distorted sounds are heard, try the following troubleshooting steps:

Remove any materials (hat, scarf, headband, etc.) that may be covering your microphone.

Visually inspect the cable for any damage or breakage. If any problems are noted, replace cable.

Verify that the cable is ﬁrmly attached to the headpiece and sound processor and that the

headpiece is positioned properly on the head.

Verify that the desired program setting and volume level have been correctly set. If synced to

an AB myPilot, do a status read out to conﬁrm correct program, volume, and sensitivity settings.

If the input is from the headpiece microphone and the static or distorted sounds persist,

replace the headpiece cable.

Visually inspect the microphones for signs of debris or wear.

If available, replace the headpiece and/or headpiece Color Cap.

Clean the battery contacts on the processor.

Replace the Microphone Cover.

Replace the T-Mic 2 Cover.

Unaided listeners may perform a listening check of the input sound sources as described

in the Listening to the Microphone and Auxiliary Inputs section of the User Guide.

Naída CI Q90 Sound Processor User Guide 57

If these measures do not resolve the problem, contact your hearing care professional or

Advanced Bionics immediately for further assistance.

If sounds are mufﬂed or distorted:

Conﬁrm that no clothing or material is obstructing the microphone opening.

Repeat the troubleshooting steps for when static is heard, listed above.

If the Naída CI battery contacts appear to have rust forming on them:

Clean the contacts with a hearing aid brush or dry cotton swab.

If the Naída CI Q90 sound processor does not power up:

Remove and replace the battery cartridge.

Verify that a charged PowerCel or two fully charged Zn-Air batteries are in place.

Verify that the PowerCel is seated properly or the Zn-Air batteries are inserted correctly.

If the problem continues, contact a hearing care professional or Advanced Bionics for

further assistance.

If no sound is heard with an FM/Roger or auxiliary audio device attached to the ComPilot:

Verify that the FM/Roger receiver and/or auxiliary audio device is attached ﬁrmly to the

ComPilot.

Verify that the ComPilot is powered on.

Verify that the FM transmitter, Roger microphone, and/or external audio device are

powered.

Verify that you are using a program which allows for auxiliary, or Aux, input to the Naída CI

and that the Naída CI is wireless enabled.

Verify that the FM/Roger receiver has been programmed for use with the Naída CI.

Verify that the ComPilot neckloop is worn correctly around the neck, with the ComPilot

lying approximately mid chest.

If these measures do not resolve the problem, contact a hearing care professional or Advanced

Bionics for further assistance.

Troubleshooting Naída CI LEDs

The Naída CI LEDs are a programmable feature providing diagnostic information regarding

battery life, microphone function, pairing capabilities, or processor status. Refer to the

58 Naída CI Q90 Sound Processor User Guide

Understanding Naída CI LEDs section of the User Guide for an explanation of the expected

LED behavior(s).

If no lights appear:

Check that the LED is not obscured by the user’s clothing, hair, and/or, processor wearing device.

Verify that the PowerCel is seated properly on the processor, or, if using Zn-Air Battery Pak,

verify that the batteries are inserted correctly.

Replace the battery.

If applicable, verify that the Naída CI Q90 is not in Standby Mode by brieﬂy pressing the

program button.

If green LED does not ﬂash in response to loud sounds (programmable feature):

Conﬁrm that this feature is enabled on the processor/program.

Verify that the PowerCel is charged and is inserted properly on the processor. If using Zinc

Air Cells, verify that the cells are new and inserted properly within the cartridge.

If paired to an AB myPilot Remote Control, check the sensitivity setting, or try increasing it

slightly for assessment purposes only.

Try another program slot.

Try another audio source (such as the T-Mic 2/processor microphone/headpiece microphone)

Unaided listeners may perform a listening check of the audio inputs as described in the

Listening to the Microphone and Auxiliary Inputs section of the User Guide.

Try another auxiliary source.

a. You will need a program which accepts input from external audio sources and to have

wireless enabled on the processor.

b. If the green LED ﬂashes in response to input from an external audio device, place the

processor and headpiece in the drying system. If the green LED still does not

ﬂash in response to loud sounds following a full drying cycle and when using the usual

microphone input and usual program settings, proceed to the next step.

If the headpiece microphone is the only input that does not show a blinking green LED, replace

the headpiece and/or cable. If T-Mic 2 is the only input that does not show a blinking green

LED, replace the T-Mic 2. If the processor microphones do not show a blinking green LED

with audio input, contact a hearing care professional or Advanced Bionics.

During battery status check, no blink or only one orange blink is observed:

REMEMBER:

Zn-Air batteries will NOT give the LED battery status upon start

up. Only the rechargeable PowerCels will give the LED battery status read out.

Naída CI Q90 Sound Processor User Guide 59

Verify that the PowerCel is seated properly on the processor.

Replace with a fully charged PowerCel.

If there are no blinks after the PowerCel replacement, clean the contacts with a hearing aid

brush or dry cotton swab.

If the problem continues, contact a hearing care professional or Advanced Bionics for

further assistance.

If the LED behaves differently following processor replacement or programming:

Verify with the recipient’s implant hearing care professional whether any program changes

have been made which may affect LED behavior.

If these measures do not resolve the problem, contact a hearing care professional or Advanced

Bionics for further assistance.

Troubleshooting Naída CI Q90 Internal Alarms

Internal alarms are a programmable feature which can be used independently or in conjunction

with the Naída CI LEDs to provide important information about status and battery life. Refer to

the Understanding Internal Alarms section of the User Guide for an explanation of the expected

internal alarm behavior(s).

If no internal alarm is heard:

Ensure the headpiece is correctly seated over the implant site.

Verify that the battery is inserted properly on the processor.

Verify that the PowerCel or Zn-Air batteries have enough charge to power the Naída CI

Q90 to stimulate the internal implant.

Replace the battery.

Change the program or volume setting to see if the internal alarm can be heard.

Verify with the recipient’s implant hearing care professional whether any program changes

have been made which may affect internal alarm behavior.

Have an unaided listener conduct a listening check to see if they can hear the internal alarms.

Please see Listening to the Microphone and Auxiliary Inputs section of the User Guide.

WARNING:

The processor or headpiece should be serviced only by Advanced Bionics.

Do not attempt to open or repair the parts. Do not continue to use the processor or

headpiece if any part of it is damaged. Unauthorized opening of the processor, headpiece,

or other equipment, will void the warranty and may compromise system performance.

60 Naída CI Q90 Sound Processor User Guide

Guidance and Manufacturer’s Declaration

Per IEC 60601-1-2

Electromagnetic Emissions

The Naída CI Q90 is intended for use in the electromagnetic environment speciﬁed below. The

customer or the user of the Naída CI Q90 should ensure that it is used in such an environment.

Electromagnetic Immunity

The Naída CI Q90 is intended for use in the electromagnetic environment speciﬁed below. The

customer or the user of the Naída CI Q90 should ensure that it is used in such an environment.

Emissions Test Compliance Electromagnetic Environment-Guidance

RF emissions

CISPR 11 Group 1

The Naída CI Q90 uses RF energy only for its

internal function. Therefore, its RF emissions

are very low and are not likely to cause any

interference in nearby electronic equipment.

RF emissions

CISPR 11 Class B The Naída CI Q90 is suitable for use in all

establishments, including domestic establishments

and those directly connected to the public

low-voltage power supply network that supplies

buildings used for domestic purposes.

Harmonic emissions

IEC 61000-3-2 Not applicable

Voltage ﬂuctuations/ ﬂicker emissions

IEC 61000-3-3 Not applicable

Immunity Test IEC 60601

Test level Compliance levela

Electrostatic

discharge (ESD)

IEC 61000-4-2

± 6 kV

contact

± 8 kV air

Floors should be wood, concrete or ceramic tile. If

ﬂoors are covered with synthetic material, the relative

humidity should be at least 30%.

Electromagnetic Environment-Guidance

± 6 kV contact

± 8 kV air

Power frequency

(50/60 Hz)

magnetic ﬁeld

IEC 61000-4-8

3 A/m Power frequency magnetic ﬁelds should be at

levels characteristic of a typical location in a typical

commercial or hospital environment.

3 A/m

Radiated RF

IEC 61000-4-3

3 V/m

80 MHz to

2.5 GHz

Portable and mobile RF communications equipment

should be used no closer to any part of the Naída

CI Q90, including cables, than the recommended

separation distance calculated from the equation

applicable to the frequency of the transmitter.

Recommended separation distance

d = 1.2√P < 800 MHz

d = 2.3√P ≥ 800 MHz

where P is the maximum output power rating of the

transmitter in watts (W) according to the transmitter

manufacturer and d is the recommended separation

distance in metres (m). Field strengths from ﬁxed RF

transmitters, as determined by an electromagnetic

site survey,b should be less than the compliance level

in each frequency range.c

Interference may occur in the vicinity of

equipment marked with the following symbol:

3 V/m

Naída CI Q90 Sound Processor User Guide 61

Recommended separation distances between portable and mobile

RF communications equipment and the Naída CI Q90

The Naída CI Q90 is intended for use in an electromagnetic environment in which radiated RF

disturbances are controlled. The customer or the user of the Naída CI Q90 can help prevent

electromagnetic interference by maintaining a minimum distance between portable and mobile RF

communications equipment (transmitters) and the Naída CI Q90 as recommended below, according

to the maximum output power of the communications equipment.

0.01

d = 1.2√P < 800 MHz

Rated Maximum Output

Power of Transmitter

(w)

Separation distance according to frequency of transmitter

(m)

d = 2.3√P ≥ 800 MHz

0.12 0.23

0.1 0.38 0.73

11.2 2.3

10 3.8 7.3

100 12 23

For transmitters rated at a maximum output power not listed above, the recommended separation

distance d in meters (m) can be estimated using the equation applicable to the frequency of the

transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to

the transmitter manufacturer.

NOTE: These guidelines may not apply in all situations. Electromagnetic propagation

is affected by absorption and reﬂection from structures, objects and people.

a Essential performance of the Naída CI Q90 per IEC 60601 requirements is deﬁned as auditory

stimulation within safe amplitudes.

b Field strengths from ﬁxed transmitters, such as base stations for radio (cellular/cordless) telephones and

land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted

theoretically with accuracy. To assess the electromagnetic environment due to ﬁxed RF transmitters, an

electromagnetic site survey should be considered. If the measured ﬁeld strength in the location in which

the Naída CI Q90 is used exceeds the applicable RF compliance level above, the Naída CI Q90 should

be observed to verify normal operation.

c Over the frequency range 150 kHz to 80 MHz, ﬁeld strengths should be less than 3 V/m.

Separation Distances between RF Communications Equipment and Naída CI Q90

NOTE: These guidelines may not apply in all situations. Electromagnetic propagation

is affected by absorption and reﬂection from structures, objects and people.

62 Naída CI Q90 Sound Processor User Guide

Compatibility Tables

1 Requires SoundWave 2.1 or later

2 Requires SoundWave 2.0 or later

3 Requires SoundWave 1.4 or later

4 Requires SCLIN 2000 and CPI-II

5 Requires SoundWave 2.3 or later and CPI-3

1 Only on Harmony™ processor

1 Requires AquaCase™ container

Software Type/Version

Implant Type

SCLIN 2000

C1 CII HiRes 90K

SoundWave 1.4 (or earlier)

✓

HiRes 90K Advantage

SoundWave 2.0

SoundWave 2.1

SoundWave 2.2

✓

✓✓

✓1✓ ✓

✓1✓✓✓

SoundWave 2.3 ✓1✓✓✓

Implant Type

Naída CI Q90

C1 CII HiRes 90K

Neptune™ sound

processor

Harmony™ processor

Platinum Sound

Processor (PSP)

✓5

✓1

✓3✓3

✓2

✓✓

✓4

✓5

✓1

HiRes 90K Advantage

✓5

✓1

Processor Type

PSP ✓✓

Headpiece Type

Naída CI Q90 ✓

Neptune

Harmony

Universal Headpiece

(UHP)

AquaMic™

Headpiece

✓1

✓✓

✓

Processor Type

Concave UHP

✓

Naída CI Q90 Sound Processor User Guide 63

Implant Type

Programming

Interface

C1 CII HiRes 90K

✓

HiRes 90K Advantage

CPI-II

CPI-3

✓ ✓ ✓

✓1✓✓✓

1 Only on Harmony

Cleaning & Maintenance

• Clean with a soft cloth. Do not immerse.

• Follow suggested routine maintenance of microphone covers for the T-Mic 2 and processor microphone.

• The Naída CI Q90 recipient kit includes a drying system; it is recommended that all

components (UHP, cable, and sound processor) run through one drying cycle (8 hrs.)

overnight on a nightly basis.

• PowerCel™ batteries should also be regularly placed in the drying system when not being

charged, particularly if exposed to moisture or perspiration.

• Batteries should not be loosely carried in pockets or handbags as this may cause debris to

accumulate on the connector. Instead, the carrying case included in the Naída CI Q90 kit

can be used for transporting batteries. If the case is not available, it is recommended that the

PowerCel batteries be sealed in a small plastic Ziploc bag.

• A canned air duster commonly used to clean keyboards or electronic equipment can also be

utilized to dry the connector on the Naída CI Q90 processor or blow out foreign debris within

the ports. For optimal results, it should also be used in combination with the drying system.

• Servicing or modiﬁcation of the Naída CI Q90 or its accessories by any entity other than

Advanced Bionics is not permitted and will void the manufacturer’s warranty.

Performance Data

The HiRes 90K Advantage implant with the HiFocus Electrode and Naída CI Q90 processor

support the HiResolution family of sound processing strategies including HiRes, HiRes with

Fidelity 120 (HiRes 120), and ClearVoice.

HiRes™ and HiRes Fidelity 120™ Sound Processing

A clinical study was conducted in 50 adults implanted with a CII/HiRes 90K device who used

a Harmony processor to document the beneﬁts of HiRes 120 and HiRes sound processing.

Performance with HiRes was accessed at the baseline visit and compared with HiRes 120

performance after three months of listening experience. Subsequently, subjects were reﬁt and

retested with HiRes. Results showed equivalent mean CNC word recognition scores for the two

64 Naída CI Q90 Sound Processor User Guide

strategies. The mean HINT sentence perception scores in quiet and noise were signiﬁcantly

higher for HiRes 120 compared to baseline with HiRes. For HINT sentences in noise, the mean

scores for HiRes 120 were signiﬁcantly higher than scores after subjects were reﬁt with HiRes.

Mean Speech Scores for HiRes and HiRes 120

* HiRes 120 score signiﬁcantly different from baseline HiRes score (p<.05)

** HiRes 120 score signiﬁcantly different from baseline and 3-month HiRes score (p<.05)

This instrument is certiﬁed under:

FCC ID: S2B-ABBTE

IC: 10870A-ABBTE

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause

undesired operation.

Changes or modiﬁcations made to this equipment not expressly approved by Advanced

Bionics may void the FCC authorization to operate this equipment.

HiRes HiRes 120 HiRes

CNC Words

HINT Sentences in Quiet

HINT Sentences in Noise

(+8 dB SNR)

Baseline 3 months 3 months

93*

70**

Naída CI Q90 Sound Processor User Guide 65

Advanced Bionics is committed to providing the highest quality products and service to our

customers. We welcome your comments regarding the Naída CI Q90 sound processor or your

suggestions to improve our products. Please feel free to contact AB or discuss your suggestions

with the recipient’s hearing care professional.

Advanced Bionics AG

Laubisrütistrasse 28

8712 Stäfa, Switzerland

T: +41.58.928.78.00

F: +41.58.928.78.90

info.switzerland@AdvancedBionics.com

Advanced Bionics LLC

28515 Westinghouse Place

Valencia, CA 91355, United States

T: +1.877.829.0026

T: +1.661.362.1400

F: +1.661.362.1500

info.us@AdvancedBionics.com

AdvancedBionics.com

Advanced Bionics, IntelliLink, AutoSound, SoundWave, HiRes, HiRes Fidelity 120, HiRes Optima, CIS, MPS,

ClearVoice, and Built Kid Tough are trademarks of Advanced Bionics in the United States of America and

other countries.

VELCRO® is a registered trademark of Velcro Industries B.V.

Bluetooth® is a registered trademark of Bluetooth SIG, Inc.

Mode d'emploi

du processeur de son Naída CI Q90

2 Mode d'emploi du processeur de son Naída CI Q90

Étiquetage

Symboles d'étiquetage et leur signiﬁcation :

Marquage de conformité de la Communauté européenne. Autorisé à apposer

le marquage CE en 2015

Numéro de modèle

Date de fabrication

Numéro de série

Fabricant

Type de protection : B

À entreposer à une température comprise entre -20 ˚C et +55 ˚C

Fragile

Évitez toute exposition à l'eau

Consultez les instructions d'utilisation

Peut être utilisé à une pression atmosphérique comprise entre 70 kPa et 106 kPa, soit entre

3000 m au-dessus du niveau de la mer et 380 m au-dessous du niveau de la mer.

Peut être utilisé à une humidité relative comprise entre 0 et 95 %

Mettre au rebus selon les règlements nationaux et locaux en vigueur

IP57 L'indice IP du Naída CI Q90 est IP57. Il indique que le Naída CI Q90 est protégé contre

la poussière, toute défaillance due à une immersion de 30 minutes à une profondeur

de 1 m maximum et après avoir passé la nuit dans un dispositif Dry and Store.

Reconditionné*

*Applicable uniquement si la mention « Reconditionné » est indiquée sur le bordereau d’expédition

Avertissements et mises en garde

AVERTISSEMENTS

• RISQUE D'ÉTOUFFEMENT : contient des pièces de petite taille pouvant être inhalées.

• N'utilisez ni ne conservez AB myPilot dans les poches de chemises, si l'utilisateur

porte un stimulateur cardiaque, car cela pourrait provoquer des interférences.

Contactez un professionnel de la santé pour obtenir de plus amples informations.

Mode d'emploi du processeur de son Naída CI Q90 3

• N'utilisez pas le ComPilot si l'utilisateur porte un stimulateur cardiaque car cela

pourrait provoquer des interférences. Contactez un professionnel de la santé

pour obtenir de plus amples informations.

• Assurez la surveillance des enfants utilisant le processeur de son et les accessoires

du Naída CI Q90.

• Conservez les piles et les accessoires hors de la portée des enfants, car ils

constituent un risque d'étouffement.

• En cas d’ingestion, consultez immédiatement un médecin ou un service d’urgence

hospitalier.

• Empêchez les enfants de jouer avec les batteries/piles et évitez de laisser

les enfants sans surveillance avec des batteries/piles.

• Évitez de mettre les piles/batteries dans la bouche.

• Évitez de mâcher ou d'avaler les batteries/piles. Si cela arrive, demandez

immédiatement un avis médical.

• Évitez de laisser les enfants manipuler le système de séchage sans surveillance.

• Toute utilisation de votre processeur de son et des accessoires différente de l'usage

prévu (par ex. les placer dans votre bouche ou les mastiquer) peut occasionner

des blessures corporelles.

• Ne chargez pas des piles jetables.

• Veillez à éviter tout contact entre le liquide provenant d'une fuite de batteries/

piles et la peau, la bouche et les yeux.

• Évitez toute exposition des batteries/piles à la chaleur (par ex. évitez de les exposer

directement à la lumière du soleil ou de les conserver dans une voiture au soleil).

• Les piles/batteries ne doivent pas être jetées au feu.

• Les enfants ne doivent pas recharger les batteries sans surveillance.

• Avec le processeur de son, la télécommande AB myPilot ou le ComPilot, n'utilisez

pas d'autre chargeur que ceux fournis par Advanced Bionics ou Phonak.

Si besoin, contactez Advanced Bionics pour faire remplacer le chargeur.

• N'utilisez pas l'AB myPilot ou le ComPilot lorsqu'ils sont connectés à des sources

d'alimentation telles que des prises murales ou des sources d'alimentation USB,

comme par exemple les ordinateurs portables.

• Le ComPilot est fourni avec une antenne « collier ». Ne touchez pas en même

temps les connecteurs de l' « antenne collier ».

• Faites fonctionner les alimentations électriques et les chargeurs de batteries dans

un espace ouvert pour garantir une circulation de l’air sufﬁsante. Bien que jusqu'à

présent, aucune blessure n'ait été signalée, les composants peuvent chauffer lors

d'une utilisation normale ou en cas de dysfonctionnement. Si la température

du dispositif vous incommode ou si vous ressentez une douleur quand vous le

portez, débranchez la source d'alimentation et contactez votre représentant local

Advanced Bionics.

4 Mode d'emploi du processeur de son Naída CI Q90

MISES EN GARDE

• Retirez l'équipement externe pour interrompre la stimulation si les sons sont

inconfortables.

• Il est important que la force de l'aimant de l'antenne soit correcte aﬁn d'éviter

toute gêne ou tout problème de maintien. Si le nombre d'aimants présents est

trop faible, l'antenne peut se détacher trop souvent. Si un nombre trop important

d'aimants est utilisé, alors l'utilisateur peut ressentir une gêne ou une irritation.

Consultez votre audiologiste en cas de problèmes liés à l'intensité de l'aimant.

Le cas échéant, un audiologiste peut ajouter ou retirer des aimants de l'antenne.

N'ajoutez pas d'aimants supplémentaires à l'antenne sans en avoir reçu

la consigne de la part d'un professionnel de l'implantation cochléaire. En cas

d'apparition d'une gêne, d'une irritation ou de rougeurs, cessez immédiatement

d'utiliser l'antenne et contactez un centre d'implant cochléaire. Pour de plus

amples informations concernant le réglage de l'intensité de l'aimant de l'antenne,

consultez les Instructions d'utilisation de l'antenne.

• Si le processeur de son ou les accessoires chauffent de façon inhabituelle, arrêtez

de les utiliser et contactez immédiatement Advanced Bionics ou votre clinicien.

• Rangez les antennes de rechange éloignées d'objets comportant des pistes

magnétiques (par ex. les cartes de crédit ou les cartes électroniques d'hôtel), car

cela pourrait les démagnétiser.

• Les dispositifs de communication à radiofréquence portables ou mobiles, y

compris les radios et les téléphones portables, peuvent altérer la qualité sonore

du processeur de son et des accessoires du Naída CI Q90 ; cependant, il n'y a pas

de risque associé à de tels dispositifs.

• Le processeur de son et les accessoires Naída CI Q90 doivent être utilisés conformément

aux informations relatives à leur compatibilité électromagnétique (CEM) fournies dans

la section Recommandations et déclaration du fabricant des instructions d'utilisation.

• Utilisez uniquement le chargeur fourni pour charger les batteries AB PowerCel.

Ne l'utilisez pas pour charger d’autres batteries/piles. N’essayez pas de charger

les batteries PowerCel du Naída CI Q90 à l’aide d’un chargeur autre que celui

fourni par Advanced Bionics.

• Retirez les piles usées de votre processeur de son pour éviter tout risque

d'endommagement par fuite d'une pile.

• Évitez d'exposer les pièces du processeur de son ou des accessoires du Naída CI

Q90 à des températures extrêmes, telles que produites par un four, un micro-

ondes ou un sèche-cheveux.

• Les piles doivent être rechargées uniquement avec le ou les chargeurs

recommandés par le fabricant.

• N'utilisez pas vos accessoires AB myPilot ou ComPilot lorsqu'il est interdit d'utiliser

des appareils électroniques sans ﬁl, comme dans les avions.

Mode d'emploi du processeur de son Naída CI Q90 5

• AB myPilot ne doit pas approcher du processeur Naída CI Q90 à moins de 1 cm

(1/2 po), lorsque l'implant est stimulé. Le non-respect de cette consigne pourrait

entraîner la perte du lien entre l'implant et le processeur de son. Si cela se produit,

éteignez le processeur et rallumez-le (en retirant la batterie/le compartiment pile

et en la/le replaçant).

• La technologie de transmission inductive à codage numérique utilisée dans

cet appareil est très ﬁable et ne subit en principe aucune interférence produite

par d’autres appareils. Il faut cependant noter qu’il peut être nécessaire

d’éloigner l’appareil d’au moins 60 cm (24 po) d’un équipement informatique

ou autres sources de champs électromagnétiques puissants, pour assurer

son fonctionnement correct. Si le Naída CI Q90 ne répond pas aux signaux

de l'appareil implanté en raison d'un champ électromagnétique perturbant

inhabituel, éloignez-vous du champ perturbant.

• Si AB myPilot cesse d'émettre les commandes au processeur de son, il peut

être nécessaire de rapparier AB myPilot et votre processeur de son. Consultez

la section Appariage au AB myPilot du présent mode d'emploi.

• Si les commandes de volume AB myPilot reçues par le processeur de son

semblent irrégulières, rappariez AB myPilot et le Naída CI Q90.

• REMARQUE : en cas de diffusion audio avec le ComPilot, si votre antenne se

déverrouille, désactivez le ComPilot avant de re-verrouiller votre antenne. À défaut,

la communication entre le processeur de son et votre implant sera empêchée.

• Nous tenons à informer les patients que l'utilisation de WindBlock, EchoBlock et/

ou SoundRelax peut affecter la qualité du son.

Décharge électrostatique (DES)

Des niveaux élevés d'électricité statique peuvent endommager les composants électroniques

de votre processeur de son ou de votre implant. Il convient donc de prendre soin d'éviter d'exposer

le système à l'électricité statique. Une DES se produit lorsque vous « prenez le jus » ou lorsque

vos cheveux se dressent sur votre tête.

Les exemples ci-dessous décrivent des situations propices à la formation d'une charge

électrostatique importante :

• Marche, marche à quatre pattes ou glissades sur moquette.

• Glissades sur des toboggans en plastique.

• Sortie d'une voiture.

• Mise et retrait de pulls.

• Contact avec des écrans de téléviseur ou d'ordinateur.

• Changement de draps et de couvertures.

6 Mode d'emploi du processeur de son Naída CI Q90

Pour réduire le risque de dommages dus à une décharge électrostatique :

• Touchez une personne ou un objet avec vos doigts avant de toucher votre antenne, cordon

ou processeur de son, ou ceux de votre enfant.

• Posez la main sur les surfaces métalliques avant d'y poser les dispositifs électroniques.

Ceci est important notamment dans les zones de jeux pour enfants où des niveaux élevés

d'électricité statique peuvent être générés. Il est important de décharger toute électricité

statique en plaçant votre main sur une surface métallique avant d'y poser le processeur de

son, le cordon ou l'antenne.

• Prenez garde d'éviter tout contact entre votre système d'implant cochléaire et des surfaces

métalliques lorsque vous sortez d'une voiture.

• Retirez votre système d'implant cochléaire avant d'enlever des vêtements pouvant générer

des décharges électrostatiques (par ex. des pulls).

• Évitez de toucher les écrans de téléviseur ou d'ordinateur. En cas de contact avec un écran,

veillez à toucher un objet autre qu'un composant de votre système d'implant cochléaire aﬁn

de libérer toute charge électrostatique accumulée avant de toucher votre système d'implant

cochléaire.

• Utilisez un adoucissant pour tissus pour vos vêtements et votre literie.

Portiques de sécurité dans les aéroports

Les portiques et les scanners de sécurité, y compris les scanners corps entiers, n'endommagent

pas votre système d'implant cochléaire ; cependant, l'alarme peut se déclencher lorsque vous

passez le portique. Pour éviter d'entendre tout son indésirable lorsque vous traversez un portique

ou un scanner de sécurité, réduisez le volume du processeur de son ou retirez votre antenne.

Capteurs à ultrasons

Les capteurs à ultrasons, utilisés parfois en tant que capteurs pour des systèmes d'éclairage ou de

sécurité, n'endommagent pas votre système d'implant cochléaire. Cependant, leur présence peut

agir sur le microphone de l'antenne et altérer la qualité sonore du processeur du son qui s'en ver-

ra déformée à proximité immédiate du capteur. De plus, dans le cas où les ultrasons sont très in-

tenses, ils peuvent endommager le microphone du système de processeur. Pour éviter d'entendre

tout son indésirable, réduisez le volume du processeur de son ou retirez votre antenne lorsque

vous passez à proximité d'un capteur à ultrasons (par ex. dans les entrées de bibliothèques).

Appareils à rayons X

Les appareils à rayons X n'endommagent pas votre processeur de son ou votre implant, mais

peuvent endommager vos Naída CI Q90 et coudes d'antenne. Évitez de ranger les coudes du

système dans des bagages enregistrés ou bagages à main qui sont contrôlés par des appareils

à rayons X. Lors des contrôles de sécurité dans les aéroports, prenez le processeur de son et le

microphone avec vous pour traverser le portique de détection ou faites-les examiner à la main.

Table des matières

Introduction ...............................................................................................................................10

Objectifs de ce mode d'emploi ..................................................................................................10

À propos du processeur de son Naída CI Q90 .................................................................10

Le processeur de son Naída CI Q90 ................................................................................11

Présentation du processeur de son Naída CI Q90 et des accessoires ................12

Le Naída CI Q90 ..............................................................................................................................12

L'antenne universelle ......................................................................................................................13

AB myPilot ............................................................................................................................................ 13

ComPilot ................................................................................................................................................14

Testeur d'écoute pour Naída CI .................................................................................................14

Boîtier AquaCase™ ...........................................................................................................................15

Téléphone DECT Phonak .............................................................................................................15

Caractéristiques du processeur de son Naída CI Q90 ..............................................16

UltraZoom auto .................................................................................................................................16