Yamaha UW10 de handleiding

Merk: Yamaha

Model: UW10

Type: de handleiding

USB-AUDIO INTERFACE

Owner's Manual

Bedienungsanleitung

Mode d'emploi

This document is printed on recycled chlorine

free (ECF) paper with soy ink.

Auf Recycling-Umweltpapier gedruckt.

Ce document a été imprimé sur du papier recyclé

non blanchi au chlore.

M.D.G., Pro Audio & Digital Musical Instrument Division,

Yamaha Corporation

305AP-01A0 Printed in China

Yamaha Web Site (English only)

www.yamahasynth.com

Yamaha Manual Library

http://www2.yamaha.co.jp/manual/english/

USB-AUDIO INTERFACE

EnglishDeutschFrançais

SPECIAL MESSAGE SECTION

This product utilizes an external power supply

(adapter). DO NOT connect this product to any

power supply or adapter other than one

described in the manual, on the name plate, or

specifically recommended by Yamaha.

WARNING:

Do not place this product in a

position where anyone could walk on, trip over,

or roll anything over power or connecting cords

of any kind. The use of an extension cord is not

recommended! If you must use an extension

cord, the minimum wire size for a 25' cord (or

less) is 18 AWG. NOTE: The smaller the AWG

number, the larger the current handling capacity.

For longer extension cords, consult a local

electrician.

This product should be used only with the

components supplied or; a cart, rack, or stand

that is recommended by Yamaha. If a cart, etc.,

is used, please observe all safety markings and

instructions that accompany the accessory

product.

SPECIFICATIONS SUBJECT TO

CHANGE:

The information contained in this manual is

believed to be correct at the time of printing.

However, Yamaha reserves the right to change

or modify any of the specifications without notice

or obligation to update existing units.

Do not attempt to service this product beyond

that described in the user-maintenance

instructions. All other servicing should be

referred to qualified service personnel.

This product, either alone or in combination with

an amplifier and headphones or speaker/s, may

be capable of producing sound levels that could

cause permanent hearing loss. DO NOT operate

for long periods of time at a high volume level or

at a level that is uncomfortable. If you

experience any hearing loss or ringing in the

ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter

the time period before damage occurs.

Some Yamaha products may have benches and/

or accessory mounting fixtures that are either

supplied with the product or as optional

accessories. Some of these items are designed

to be dealer assembled or installed. Please

make sure that benches are stable and any

optional fixtures (where applicable) are well

secured BEFORE using. Benches supplied by

Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of

knowledge relating to how a function or effect

works (when the unit is operating as designed)

are not covered by the manufacturer's warranty,

and are therefore the owners responsibility.

Please study this manual carefully and consult

your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are

both user safe and environmentally friendly. We

sincerely believe that our products and the

production methods used to produce them, meet

these goals. In keeping with both the letter and

the spirit of the law, we want you to be aware of

the following:

Disposal Notice:

Should this product become damaged beyond

repair, or for some reason its useful life is

considered to be at an end, please observe all

local, state, and federal regulations that relate to

the disposal of products that contain lead,

batteries, plastics, etc. If your dealer is unable to

assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the

product. The model number, serial number,

power requirements, etc., are located on this

plate. You should record the model number,

serial number, and the date of purchase in the

spaces provided below and retain this manual as

a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

93-DC

* Please make a note of the model number, the serial number and the purchase date.

UW10 Owner’s Manua

English

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death

from electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are

not limited to, the following:

• Check the USB connector periodically and remove any

dirt or dust which may have accumulated on it.

• Do not place the cable near heat sources such as heat-

ers or radiators, and do not excessively bend or other-

wise damage the cable, place heavy objects on it, or

place it in a position where anyone could walk on, trip

over, or roll anything over it.

• Do not open the instrument or attempt to disassemble the

internal parts or modify them in any way. The instrument

contains no user-serviceable parts. If it should appear to

be malfunctioning, discontinue use immediately and have

it inspected by qualiﬁed Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or

in damp or wet conditions, or place containers on it con-

taining liquids which might spill into any openings.

•Never insert or remove cables with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

• If the USB cable becomes frayed or damaged, or if there is a

sudden loss of sound during use of the instrument, or if any

unusual smells or smoke should appear to be caused by it,

immediately disconnect the USB connector, and have the

instrument inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not expose the instrument to excessive dust or vibra-

tions, or extreme cold or heat (such as in direct sunlight,

near a heater, or in a car during the day) to prevent the

possibility of panel disﬁguration or damage to the inter-

nal components.

• Do not use the instrument in the vicinity of a TV, radio, ste-

reo equipment, mobile phone, or other electric devices.

Otherwise, the instrument, TV, or radio may generate noise.

• Do not place the instrument in an unstable position

where it might accidentally fall over.

• Before moving the instrument, remove all connected

cables.

• Before connecting the instrument to other electronic

components, turn off the power for all components.

Before turning the power on or off for all components, set

all volume levels to minimum. Also, be sure to set the

volumes of all components at their minimum levels and

gradually raise the volume controls while playing the

instrument to set the desired listening level.

• When cleaning the instrument, use a soft, dry cloth. Do

not use paint thinners, solvents, cleaning ﬂuids, or chem-

ical-impregnated wiping cloths.

• Do not insert a ﬁnger or hand in any gaps on the instrument.

•Never insert or drop paper, metallic, or other objects into

the gaps on the panel. If this happens, disconnect the

USB cable. Then have the instrument inspected by qual-

iﬁed Yamaha service personnel.

• Do not place vinyl, plastic or rubber objects on the instru-

ment, since this might discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the

instrument, and do not use excessive force on the but-

tons, switches or connectors.

Cables

Do not open

Water warning

Fire warning

If you notice any abnormality

Location

Connections

Maintenance

Handling caution

(3)-7

UW10 Owner’s Manual

English

• Do not operate the instrument for a long period of time at

a high or uncomfortable volume level, since this can

cause permanent hearing loss. If you experience any

hearing loss or ringing in the ears, consult a physician.

Yamaha cannot be held responsible for damage

caused by improper use or modifications to the

instrument, or data that is lost or destroyed.

(3)-7

UW10 Owner’s Manua

English

Welcome to the UW10

Thank you for choosing the Yamaha UW10 USB-Audio Interface. The UW10 is a

USB interface that enables simultaneous transfer of audio data. Connect the

UW10 to a computer that has a USB connector and enjoy the powerful features of

digital audio.

Please read this Owner’s Manual thoroughly to make the best use of the UW10.

After you read this manual, please keep it in a safe place for future reference.

Table of contents

UW10 Features................................................................................. 6

Notes on USB ......................................................................... 6

Notes on musical copyrights ................................................... 7

Package Contents............................................................................. 8

About the included software ................................................... 8

System Requirements ..................................................................... 10

Parts and Functions ........................................................................ 10

Signal Flow ........................................................................... 12

Connections................................................................................... 13

Installing the driver ........................................................................ 16

Installing the driver ............................................................... 16

Setting up the included software .......................................... 24

Using the UW10............................................................................. 26

Recording the data from vinyl records

or cassette tapes to a computer ............................................ 26

Creating a single song file from a digital recording ............... 27

Recording MIDI data as digital audio data ............................ 27

Storing digital recordings on a music CD .............................. 28

Specifications ................................................................................. 29

Troubleshooting (FAQ)................................................................... 29

• Before installing the software, be sure to read the software license agreement included at the end

of this document. Opening the CD-ROM package indicates your consent to the license agreement.

• The company names and product names in this Owner’s Manual are the trademarks or registered

trademarks of their respective companies.

• OMS

and are trademarks of Opcode Systems, Inc.

• MPEG Layer-3 audio compression technology licensed by Fraunhofer IIS and THOMSON

Multimedia.

• “SoftSynthesizer” is a trademark of Yamaha Corporation.

The screen displays and illustrations in this Owner’s Manual are for instructional purposes, and

may appear somewhat different from the screens that appear on your computer or in the

specifications for your unit.

UW10 Owner’s Manual

English

UW10 Features

●

Digital and analog interface

The UW10 functions as an interface that enables you to digitally record MDs and

cassette tapes to a computer, or create music using an audio/MIDI sequencer and

MIDI tone generators (MOTIF-RACK etc.). The analog inputs on the UW10

convert incoming analog signals into digital. This prevents audio deterioration

due to computer noise and enables you to perform clean, clear sound recordings.

●

Easy Hot Swap Connection

You can connect and disconnect a USB cable while the power to the computer is

turned on. The power is provided through the USB bus power supply. For this

reason, the UW10 does not require a power adapter.

●

Versatile software programs

An included software program, called TWEplus Wave Editor, enables you to record

via the UW10 and edit various wave files (MP3, WAV, AIFF). Another program, the S-

YXG50 SoftSynthesizer, enables you to play MIDI data on the computer, record it,

then convert it into a wave file in TWEplus, with the UW10 set in Track Down mode.

●

Supports Windows

The UW10 supports Windows 98/Me/2000/XP.

Notes on USB

Do not connect or disconnect a USB cable under any of the following

circumstances. Otherwise, the computer may lock up or the UW10 functions may

be disabled:

•

The computer is checking the device or loading the driver.

•

The computer is starting or quitting the OS.

•

The computer is in Save Energy (Sleep) mode or is canceling the mode.

•

An audio/MIDI application is active.

In addition, do not perform any of the following operations. Otherwise, the

computer may lock up or the UW10 functions may be disabled:

•

Frequently connecting and disconnecting the cables

•

Placing the computer in Save Energy (Sleep) mode or cancelling the mode dur-

ing audio data transfer

•

Connecting or disconnecting the cables, restarting or shutting down the com-

puter, or installing or uninstalling the driver while a large amount of data is

being transferred

UW10 Owner’s Manua

English

Notes on musical copyrights

The UW10 supports SCMS (Serial Copy Management System) to protect

copyrights associated with music software. When you copy data from CDs, or

other music media purchased from stores, to your own media (such as MDs)

using a digital connection, information regarding the digital recording generation

is also recorded. If you route the recorded data to a DIGITAL IN jack, you will be

unable to record the data on a computer. In this case, use the UW10’s analog

inputs (INPUT jacks) to record data on the computer.

It is prohibited to use copyrighted songs and sound data (that can be

recorded via the UW10) for commercial purposes. It is also prohibited to

reproduce, transfer, or distribute the data, or play the data for a commercial

audience without permission from the owners of the copyright, except for

personal use or applications that do not infringe the copyright. If you wish to

use such data for occasions other than personal use, consult a copyright

expert. Yamaha is not responsible for any data created, reproduced, or edited

using the UW10, nor for any reproduction or use of such data.

computer

digital

digital analog

digital

UW10

USB-AUDIO INTERFACE

SOURCE SELECT

DIGITAL INPUT OUTPUT

IN OUT L R L R

DIGITAL

INPUT

TRACK DOWN

USB-AUDIO INTERFACE

SOURCE SELECT

DIGITAL INPUT OUTPUT

IN OUT L R L R

DIGITAL

INPUT

TRACK DOWN

You cannot

record.

You can

record.

UW10 Owner’s Manual

English

Package Contents

The UW10 package contains the following items. Check the contents for missing

items.

•

UW10 main unit

•

CD-ROM

•

USB cable (approx. 2 meters)

•

Owner’s Manual (this book)

About the included software

The included CD-ROM contains the following software programs.

The “English” folder on the included CD-ROM contains the following software

programs.

Each program’s operating environment may be different from the UW10’s operating

environment (page 10). For more information, refer to the software on-line manuals.

TWEplus Wave Editor

TWEplus Wave Editor enables you to record, play, and edit Wave files. It supports

various file formats, such as MP3, WAV, and AIFF, and can convert these file

formats from one into another. Double-click “Setup.exe” in the “TWEplus_”

folder to start the installer. Follow the instruction on screen to install the software.

After you finish the installation, start the application by selecting from the “Start”

menu [Programs | YAMAHA TWEplus | Wave Editor TWEplus]. For more

information on using the software, refer to the on-line manual.

SoftSynthesizer (S-YXG50)

The S-YXG50 is XG tone generator software that produces voices using the

computer’s CPU power. By installing SoftSynthesizer, you can enjoy high tonal

quality from MIDI data without connecting an external MIDI tone generator.

To start the installer, double-click “Setup.exe” in the “Syxg50_” folder. Install

SoftSynthesizer following the instructions on screen.

NOTE

UW10 Owner’s Manua

English

For more information on using the software, after you finish the installation,

refer to the “S-YXG50 Help” file by selecting from the “Start” menu [Programs

| YAMAHA SoftSynthesizer S-YXG50 | S-YXG50 Help].

Windows 2000/XP Users:

If you hear sound skips from the S-YXG50 on the Windows 2000/XP platform, you

may be able to resolve the problem by following the steps below:

1. From the “Start” menu, select [Programs | YAMAHA XG SoftSynthesizer S-YXG50 |

S-YXG50 Settings] to display the “Settings” window.

2. Click the “Information” tab. If the window indicates “Ver.4.01.xx Legacy” (xx is a

version number) for the S-YXG50 version, proceed to Step 3.

3. Log on to Windows as Administrator, then open the “Syxg50_” folder on the

included CD-ROM.

4. Right-click “Turbo.inf” or “Normal.inf” in the folder to display the pop-up menu, then

select “Install” from the menu.

Nomal.inf: The sound might skip occasionally, but most sound cards will output sound.

Turbo.inf: The sound will not skip, but some sound cards may not output sound.

5. Restart the computer.

XGplayer

You can use XGplayer to play MIDI data, which you can output via

SoftSynthesizer, then record it as a wave file in TWEplus with the UW10 in

Track Down mode.

This application is automatically installed when you install the S-YXG50

SoftSynthesizer. To start XGplayer after you finish the installation from the

“Start” menu, select [Programs | YAMAHA SoftSynthesizer S-YXG50 | XGplayer].

Acrobat Reader

The Acrobat Reader allows you to view an electronic version of the Owner’s

Manual saved in PDF format.

To start the installer, open the “English” folder in the “Acroread_” folder, then

double-click “ar500enu.exe.” Install the software according to the instructions

on screen.

MidRadio Player

MidRadio Player receives and plays MIDI and Sound VQ data, sort of like a

radio channel. You can listen to pieces of music continuously by connecting to

the Internet and selecting your favorite channel. You can also purchase song

data on the Internet.

To install MidRadio Player, double-click “mr4221E.exe” in the “Midradio_”

folder to start the installer, then follow the instruction on screen.

NOTE

UW10 Owner’s Manual

English

ASIO driver

This driver software is required if you wish to use applications that support

ASIO. Refer to the “ReadMe.html” in “English” folder in the “ASIOdrv_” folder

for information on how to install the driver.

TWEplus does not support ASIO.

System Requirements

Computer: IBM PC/AT or compatible computer that features a

USB connector

CPU: Intel

Pentium

or Celeron

processor with

500MHz or faster

(Windows XP: Intel

Pentium

or Celeron

processor, 750MHz or faster)

Memory: 64MB or more (128MB or more recommended)

Available hard disk space: 10MB or more

(excluding the space required for Acrobat Reader

and MidRadio Player)

Operating System: Windows 98/98SE/2000/Me/XP

Some operating systems may require a superior environment than that specified above.

Parts and Functions

1 Power LED

The LED lights up when the USB

connector is connected and the

power is being supplied from the

computer to the unit.

2 SOURCE SELECT switch

Use this switch to select the INPUT

jacks or the DIGITAL IN jack. If you

select “TRACK DOWN,” an audio

signal input from the computer to

the UW10 is returned to the

computer unmodified (page 15).

NOTE

SOURCE SELECT

IN OUT L R

DIGITAL INPUT

OUTPUT

DIGITAL

INPUT

TRACK DOWN

USB-AUDIO INTERFACE

35467

UW10 Owner’s Manual 11

English

In this case, the INPUT and DIGITAL

IN jacks are disabled.

With some application programs, input

audio signals may be output unmodified. In

this case, do not set the SOURCE SELECT

switch to “TRACK DOWN.” Otherwise,

audio signals may oscillate, causing hearing

loss or damage to the playback device.

3 USB connector

Connect this connector to a

computer’s USB connector using a

USB cable.

You do not have to turn off the

power to the computer when you

connect this

connector

4 DIGITAL IN jack

A digital signal is input here from

an MD or CD player via an optical

digital cable (with square plugs).

Set the SOURCE SELECT switch on

the side panel to “DIGITAL.”

5 DIGITAL OUT jack

This jack is used to record a digital

signal from the computer to a

digital recorder, such as an MD

recorder. Use an optical digital

cable (with square plugs) to make

the connection.

Signals input at INPUT and

DIGITAL IN cannot be routed

directly to the DIGITAL OUT jack.

6 INPUT L/R jacks

Connect an audio device, such as a

CD player, here using RCA pin

cables. You can record an audio

signal input here to a computer.

Set the SOURCE SELECT switch on

the side panel to “INPUT.”

7 OUTPUT L/R jacks

These jacks are used to connect

powered speakers or a recording

device, such as a tape recorder. Use

RCA pin-plug cables for the L and R

connections.

8 Volume Dial

The Volume Dial adjusts the level of

signals output from the headphone

jack and OUTPUT jacks. Use the

Volume Dial to adjust the output level.

9 Headphone jack

Connect a headphone stereo mini-

plug here. Use the Volume Dial to

adjust the headphone volume.

CAUTION

NOTE

12 UW10 Owner’s Manual

English

Signal Flow

Depending on the SOURCE SELECT switch setting, the audio signal flow varies as

follows:

When the switch is set to “INPUT”:

Audio signals input at the INPUT jacks can be recorded to a computer via the USB

connection.

When the switch is set to “DIGITAL”:

Audio signals input at the DIGITAL IN jack can be recorded to a computer via the

USB connection.

When the switch is set to “TRACK DOWN”:

Audio signals played on the computer can be returned via the USB connection to

the computer for recording (page 15).

ININ OUTOUT

DIGITALUSB

INPUT OUTPUT

Headphone

VOLUME

ININ OUTOUT

DIGITALUSB

INPUT OUTPUT

Headphone

VOLUME

ININ OUTOUT

DIGITALUSB

INPUT OUTPUT

Headphone

VOLUME

UW10 Owner’s Manual 13

English

Connections

Combining the UW10 with other devices allows for versatile applications as

follows:

● High-quality music production system using digital connections

Using the UW10 along with a tone generator, such as MOTIF-RACK, enables high-

quality recording.

Connect the UW10, the MOTIF-RACK and a computer using USB cables. Connect

the MOTIF-RACK to the UW10’s DIGITAL IN jack, and set the UW10’s SOURCE

SELECT switch to “DIGITAL.”

Since the signal is sent from the UW10 or MOTIF-RACK to a mixer via an analog

connection, you will be monitoring an analog signal through powered speakers or

headphones. On the other hand, the signal is recorded via a digital connection

from the UW10’s DIGITAL OUT jack to a connected MD recorder. This

configuration enables you to make high-quality digital recordings.

When you are using the connections illustrated above, set the Echo Back setting of

your sequence software to “Off.”

Refer to the Owner’s Manual for the sequence software for detailed information on

setting the Echo Back parameter.

PC + Sequence Software

UW10

DIGITAL

OUT

DIGITAL OUT

INPUT

OUTPUT

DIGITAL IN

MOTIF-RACK etc.

USB-AUDIO INTERFACE

SOURCE SELECT

DIGITAL INPUT OUTPUT

IN OUT L R L R

DIGITAL

INPUT

TRACK DOWN

DIGITAL

OUT

Mixer, etc

USB (MIDI data)

Set the SOURCE

SELECT switch

to “DIGITAL.”

USB

(audio data)

MD Recorder,etc

powered speakers

NOTE

14 UW10 Owner’s Manual

English

●Music production system using a guitar or microphone via

analog connections

Analog audio signals input from a guitar or microphone are converted to digital

for recording.

Patch the analog input from the guitar or microphone to the UW10’s INPUT jacks via

an effects unit or other equivalent device. In this case, set the UW10’s SOURCE SELECT

switch to “INPUT,” and connect powered speakers or headphones to the UW10.

●Connecting audio devices

Digital or analog input from an audio device can be converted to wave files on a

computer. You can also edit the wave files on the computer, then record them to

an audio device.

Patch a digital signal from an MD player to the UW10’s DIGITAL IN jack. Patch an

analog signal from a casette tape player or turntable to the UW10’s INPUT jacks.

Set the UW10’s SOURCE SELECT switch to “DIGITAL” or “INPUT” depending on

the jacks you are using. Connect an AV amplifier and mixer as necessary.

If you cannot adjust the output level of the audio device, some high volume sound sources

may distort your recordings, or low volume sound sources may create recordings that are

not inaudible. In this case, adjust the sound source level using the following measures:

• Connect the PHONE jack of the audio device to the UW10, then adjust the PHONE

level on the audio device.

• Connect a mixer or other device that enables you to adjust the volume level

between the audio device and the UW10.

If you try to record from a digital audio device (such as an MD or CD player) that has

an optical digital output, use an optional optical digital cable (with square plugs) to

connect the UW10. In this case, you do not have to adjust the level, since the

recording level will be the same as the sound source level.

UW10

USB-AUDIO INTERFACE

SOURCE SELECT

DIGITAL INPUT OUTPUT

IN OUT L R L R

DIGITAL

INPUT

TRACK DOWN

INPUT

OUTPUT

USB

DIGITAL

OUT

computer

guitar

microphone

Set the SOURCE

SELECT switch

to “INPUT.”

effects unit or

other equivalent device

mixer

MD recorder

powered speakers

NOTE

UW10 Owner’s Manual 15

English

●Track down on the computer

You can track down multiple wave files or SoftSynthesizer audio signals into a

single wave file, which can then be converted to an MP3 file using the included

TWEplus wave editor.

Connect the computer and the UW10, and set the UW10’s SOURCE SELECT switch

to “TRACK DOWN.” While playing MIDI or audio data on the computer, record it

using an audio editing application, such as TWEplus, to track down the data.

If you want to track down an external MIDI tone generator’s sound along with the data

on the computer, you will first need to convert the playback data into wave files.

UW10

USB-AUDIO INTERFACE

SOURCE SELECT

DIGITAL INPUT OUTPUT

IN OUT L R L R

DIGITAL

INPUT

TRACK DOWN

INPUT OUTPUT

USB

DIGITAL OUT

DIGITAL IN

computer

cassette tape deck

turntable

AV amplifier and mixer

speakers

MD recorder

NOTE

UW10

USB-AUDIO INTERFACE

SOURCE SELECT

DIGITAL INPUT OUTPUT

IN OUT L R L R

DIGITAL

INPUT

TRACK DOWN

OUTPUT

USB USB

computer

S-YXG50

XG Player

SoftSynthesizer

TWEplus

playback recording

Set the SOURCE

SELECT switch

to “TRACK DOWN.”

powered speakers

16 UW10 Owner’s Manual

English

Installing the driver

Before you can use the UW10, you need to install the driver on the computer.

The USB audio driver enables you to transfer audio signals between an audio

application on the computer and the UW10 via a USB cable.

The UW10 does not work with a USB hub that is powered by the USB bus power

supply.

Installing the driver

Follow the instructions below to install the USB audio driver included in the

Windows system, and set up Windows as needed.

Close all applications and windows on the computer, and disconnect the computer

from the network and the Internet.

Disconnect all devices that are connected to the UW10’s jacks, except for the USB

connector.

Disconnect all USB devices, except for the UW10, from the computer. Connect the

UW10 directly to the computer’s USB connector, not via a USB hub.

Check the drive name (D:, E:, Q:, etc.) of your CD-ROM drive, which is listed below the

CD-ROM icon in My Computer.

If the driver for another USB audio device has already been installed, you can use that

driver for the UW10.

You need the ASIO driver software to use applications that support ASIO. Refer to the

“ReadMe.html” file located in the “English” folder in the “ASIOdrv_” folder for

information on installing the driver software.

Windows 98/98SE users→page 17

Windows Me users→page 20

Windows 2000/XP users→page 20

audio

application

driver

UW10

USB cable

audio data

USB-AUDIO INTERFACE

SOURCE SELECT

DIGITAL INPUT OUTPUT

IN OUT LR LR

DIGITAL

INPUT

TRACK DOWN

computer

NOTE

UW10 Owner’s Manual 17

English

●Installing the driver on a Windows 98/98SE system

1. Start the computer.

2. Use the included USB cable to connect the UW10 to the computer’s USB con-

nector. The UW10 is powered on and the system automatically displays the

“Add New Hardware Wizard.”

3. Click [Next].

The system displays a screen that enables you to select a search method.

18 UW10 Owner’s Manual

English

4. Check the radio button to the left of “Search for the best driver for your device.

(Recommended).” Click [Next].

The system displays a screen that enables you to select a location in which to

install the driver.

5. Uncheck all items, then click [Next].

6. When the system detects the driver and is ready for installation, it displays the

following screen.

Make sure that the “USB Composite Device” is listed, then click [Next]. The

system starts the installation.

The system may ask you to insert a Windows CD-ROM while it checks for the driver.

Insert the Windows CD-ROM in the CD-ROM drive, specify the root folder of the CD-

ROM drive (such as D:\Win98\) and continue the installation. Drive and root folder

names vary depending on the computer.

NOTE

UW10 Owner’s Manual 19

English

7. When the installation is complete, the following screen appears.

Click [Finish].

Some computers may take about ten seconds to display this screen after installation is

complete.

8. After a few seconds, the “Add New Hardware Wizard” is displayed again.

Install “USB Audio Device” in the same manner as steps 3-7 described above.

The driver has been installed.

NOTE

20 UW10 Owner’s Manual

English

●Installing the driver on a Windows 2000/XP system

1. Start the computer.

2. Use the included USB cable to connect the UW10 to the computer’s USB connector.

The system displays the message “Found New Hardware” and automatically

detects and installs the driver.

The window closes and the driver is installed.

●Installing the driver on a Windows Me system

1. Start the computer.

2. Use the included USB cable to connect the UW10 to the computer’s USB connector.

The UW10 is powered on and the system automatically displays the “Add New

Hardware Wizard.”

3. Check the radio button to the left of “Automatic search for a better driver (Rec-

ommended).” Click [Next].

4. When the system ﬁnishes detecting and installing the driver, it displays the fol-

lowing message: “Windows has ﬁnished installing the new hardware device.”

Click [Finish].

The driver has been installed.

●Verifying the installation

You can verify whether the driver has been installed correctly by following the

steps below:

1. Double-click [My Computer | Control Panel | System].

If the System folder does not appear in the Control Panel on the Windows Me system,

click “view all Control Panel options.”

For Windows XP users: Click “Switch to Classic View” to change the Control Panel to

Classic View mode.

NOTE

UW10 Owner’s Manual 21

English

2. Click the “Device Manager” tab. “USB Audio Device” should be listed under

“Sound, Video and Game Controllers.”

On a Windows 2000/XP system, click the “Hardware” tab, then click the “Device

Manager” tab.

●Specifying the output destination of audio signals

This section explains how to set up Windows to use the UW10. For information on

setting up your sequence software, refer to the owner’s manual for the

corresponding software.

Setup for audio playback and recording

1. Double-click [My Computer | Control Panel | (Sounds and) Multimedia].

2. Click the “Audio” tab.

3. Click the “Preferred device” box and select “USB Audio Device” in “Playback”

and “Recording” respectively.

“USB Audio Device (1)” may appear, depending on the computer. If two or more USB

audio devices are connected, the corresponding number appears in parentheses.

4. Click the “Use only preferred devices” checkbox.

5. On the Windows Me system, click the “Audio” tab and select “USB Audio

Device” in “Sound Playback” and “Sound Recording” respectively.

If you are using a voice recognition system or Internet Phone with another audio

device, you may need to set the output destination to suit the environment. For more

information, refer to the documentation for the audio device.

6. Click [OK].

NOTE

Windows 98 Windows Me

NOTE

22 UW10 Owner’s Manual

English

Setup for music CDs

Follow the steps below to play a music CD in the computer’s CD-ROM drive and

output the sound digitally from the UW10.

Setup on a Windows 98 system

1. Double-click [My Computer | Control Panel | Multimedia].

2. Click the “CD Music” tab.

3. Make sure that the CD-ROM drive (e.g., “D:”) is selected correctly.

4. Check the “Enable digital CD audio for this CD-ROM device” checkbox and

click [OK].

Setup on a Windows Me/2000/XP system

UW10 Owner’s Manual 23

English

1. Double-click [My Computer | Control Panel | System].

2. Select “Device Manager,” “CD-ROM” (the listed item with a “+” mark), then

the CD-ROM drive name, then click “Properties.”

On a Windows 2000/XP system, click the “Hardware” tab, then click “Device Manager.”

3. Click the “Properties” tab.

4. Check the “Enable digital CD audio for this CD-ROM device” checkbox and

click [OK].

Setup for Volume Control

1. From the “Start” menu, select [Programs | Accessories | Entertainment | Volume

Control] to open the “Volume Control” window.

2. Move the slider to adjust the volume level.

●Checking wave ﬁle playback

Follow the steps below to check to see whether you can hear a wave file play back

from the UW10.

1. Select [My Computer | Control Panel | (Sounds and Multimedia) | Sounds].

2. Select an item with a speaker icon, then click the Play button to make sure that

the playback sound is output from the headphones or speakers connected to

the UW10.

NOTE

Windows 98 Windows Me

24 UW10 Owner’s Manual

English

Setting up the included software

Before using the included software with the UW10, follow the procedure below to

set up the application.

• TWEplus Wave Editor

From the menu bar, select [Options], then [Windows Sound Device

Configuration], and set as shown below:

• S-YXG50 SoftSynthesizer and XGplayer

From the “Start” menu, select [Programs | YAMAHA SoftSynthesizer S-YXG50 |

SYXG50], then set parameters as shown below:

UW10 Owner’s Manual 25

English

Sampling frequencies available for different OS and input jacks

Sampling frequencies available for recording in TWEplus vary depending on the

operating system and the type of input jacks.

Sampling frequencies supported for playback on different operating systems

When you play data in TWEplus or using the S-YXG50, the frequency of the

signals output from the DIGITAL OUT jack varies depending on the computer’s

operating system, as follows:

Make sure that the audio recording device (such as an MD recorder) connected to

the DIGITAL OUT jack supports these sampling frequencies.

The data output from the analog OUTPUT jacks will play correctly using any of the

sampling frequencies listed in the table.

SOURCE SELECT

switch setting

(Inputs being

used)

Sampling frequency in the software

11.025

kHz

22.05

kHz

44.1

kHz

Windows98

DIGITAL X X O O O

INPUT X X O O O

Windows98SE/

Me/2000/XP

DIGITAL X X O O O

INPUT O O O O O

Sampling frequencies for software playback

11.025kHz 22.05kHz 32kHz 44.1kHz 48kHz

Windows98 44.1kHz 44.1kHz 32kHz 44.1kHz 48kHz

Windows98SE/

Me/2000/XP

48kHz 48kHz 32kHz 44.1kHz 48kHz

NOTE

26 UW10 Owner’s Manual

English

Using the UW10

Make sure that the hard disk has enough free space. If there is insufficient space, you

may be unable to record successfully.

Recording the data from vinyl records or cas-

sette tapes to a computer

1 Setting up the UW10

1-1 Connect the UW10 to a computer.

1-2 Use an audio cable to connect the UW10’s INPUT jacks to the output jacks

of the AV device that plays the recording source.

The output jacks on the AV device could be AUX OUT jacks, external output jacks, or a

headphone jack. If you connect it to the headphone jack, you can raise the recording level.

1-3 Set the UW10’s SOURCE SELECT switch to “INPUT.”

2 Starting TWEplus

2-1 Start TWEplus on the computer.

The “Browse for Folder” window opens.

2-2 Select a recording destination folder on the hard disk, then click [OK].

You can usually select the default folder.

3 Setting up a new ﬁle

3-1 From the [File] menu, select [New...].

The “New” window opens.

3-2 Select a file format.

Generally, select “WAVE 44100Hz 16bit stereo” for music CDs. This is the

default setting.

3-3 Specify a “In Time” value for the “Length” parameter.

Specify the duration that is slightly longer than that of one side of the vinyl

record or cassette tape you wish to record. For example, if the recording source

is a 60-minute cassette tape, specify something like “32 min 0 sec 0 msec.”

Recording the data

from vinyl records or

cassette tapes to a

computer (page 26)

Recording MIDI data

as digital audio data

(page 27)

Creating a single song

file from a digital

recording

(page 27)

Storing digital

recordings on a

music CD

(page28)

Work Flow

NOTE

UW10 Owner’s Manual 27

English

3-4 Click the [New] button. The “New” window closes.

4 Digital recording

4-1 From the [Options] menu, select [Windows Sound Device Configuration...],

then select “YAMAHA UW10” or “USB Audio Device” for “Input” and

“Output”.

4-2 Click the Record button in TWEplus, then immediately start playing the

vinyl or cassette tape.

4-3 When the playback of one side finishes, click the Stop button in TWEplus.

If the recording level is low, record the output from the AV device’s headphone jack, or

raise the recorded level using the Normalize function.

Creating a single song ﬁle from a digital

recording

1 Select a single song from the waveform of the recorded data by

using the arrow tool.

2 From the [Edit] menu, select [Selection to New].

The selected region opens as a new single file.

3 From the [File] menu, select [Save As...] to save the song to a

speciﬁed location on the hard disk.

A single song is stored as a file in the computer.

Repeat this procedure to create more song files.

Recording MIDI data as digital audio data

1 Setting up the UW10

1-1 Connect the UW10 to the computer.

1-2 Set the UW10’s SOURCE SELECT switch to “TRACK DOWN.”

NOTE

28 UW10 Owner’s Manual

English

2 Starting the S-YXG50 SoftSynthesizer

2-1 Start the S-YXG50 SoftSynthesizer

To start the S-YXG50 SoftSynthesizer, from the “Start” menu select [Programs |

YAMAHA XG SoftSynthesizer S-YXG50 | XGplayer].

2-2 Click the [Set] in XGplayer.

2-3 Select “YAMAHA SXG Driver,” then click [OK].

2-4 Click the Song Select button in the XG Player’s Player window to select

MIDI data that you wish to add to the play list and convert to audio data.

Play the selected MIDI data to make sure that the UW10 outputs the sound correctly.

3 Starting TWEplus

3-1 Start TWEplus on the computer.

The “Browse for Folder” window opens.

3-2 Select a recording destination folder on the hard disk, then click [OK].

You can usually select the default folder.

4 Setting up a new ﬁle

4-1 From the [File] menu, select [New...].

The “New” window opens.

4-2 Select a file format.

Generally, select “WAVE 44100Hz 16bit stereo” for music CDs. This is the

default setting.

4-3 Specify a “In Time” value for the “Length” parameter.

Specify the duration that is slightly longer than that of the selected MIDI

data. For example, if the data consists of three five-minute songs, specify

something like “16 min 0 sec 0 msec.”

4-4 Click the [New] button. The “New” window closes.

5 Digital recording

5-1 From the [Options] menu, select [Windows Sound Device Configuration...],

then select “YAMAHA UW10” or “USB Audio Device” for “Input” and

“Output”.

5-2 Click the Record button in TWEplus, then immediately activate the

XGPlayer window and click the Play button.

5-3 When the playback in XGPlayer finishes, click the Stop button in

TWEplus.

Storing digital recordings on a music CD

1 Start your CD writer software.

2 Save each song ﬁle on a music CD.

For more information on storing data on a music CD, refer to the

documentation for your CD writer software.

NOTE

UW10 Owner’s Manual 29

English

Speciﬁcations

Audio Capability: One stereo-line recording

One stereo-line playback

Sampling Frequencies Input:32 kHz, 44.1 kHz, 48 kHz

Output:32 kHz, 44.1 kHz, 48 kHz

Jacks and connectors: Digital in jack (optical)

Digital out jack (optical)

Line in jacks (RCA pin, L/R)

Line out jacks (RCA pin, L/R)

USB connector

Headphone jack (stereo mini)

Power Supply: USB bus power supply

Dimensions: 111(W) ××

××

65(D) ××

××

31(H) [mm]

Weight: 95g

Option: Optical digital cable (with optical plugs)

Specifications and descriptions in this Owner’s Manual are provided for

information purposes only. Yamaha Corporation reserves the right to change or

modify products or specifications at any time without prior notice. Since

specifications, equipment or options may not be the same in every locale, please

check with your Yamaha dealer.

Troubleshooting (FAQ)

●The driver cannot be installed.

• Is the USB cable connected correctly?

→ Check the USB cable connection. (page 13)

→ Disconnect the USB cable, then re-connect it.

• Is the USB function enabled on your computer?

→ When you connect the UW10 to the computer for the ﬁrst time, if the “Add New

Hardware Wizard” (page 16) does not appear, the USB function on the computer

may be disabled. Perform the following steps.

1. Select [Control Panel | System | (Hardware) | Device Manager].

2. Make sure that “Universal Serial Bus Controller” and “USB Route Hub” are

not marked with “!” or “x.” If one of these items is marked with “!” or “x,”

you cannot use USB connections. For more information, refer to the docu-

mentation that came with your computer.

30 UW10 Owner’s Manual

English

• Is any device recognized as an unknown device?

→ If driver installation fails, the UW10 will be recognized as an “Unknown device,”

and you will not be able to install the driver. Delete the “Unknown device” by fol-

lowing the steps below.

1. Select [Control Panel | System | (Hardware) | Device Manager].

2. Check the “View devices by type” radio button (for Windows Me users), or

select “Devices by type” from the “View” menu (for Windows 2000/XP),

then check whether there are any “Other devices.”

3. If an “Other devices” is listed, double-click it. If there is “Unknown device”

listed below it, select the “Unknown device”, then click the [Delete] button.

4. Remove the USB cable from the UW10, then re-connect it.

5. Try to install the driver again.

• Are you using a USB hub?

→ If the UW10 is connected to a USB hub that is powered by the USB bus power

supply, the UW10 will not operate.

→ Connect the UW10 directly to the computer, then try to install the driver again. If

the computer has multiple USB connectors, try to connect the UW10 to another

USB connector.

• Is another USB device connected to the computer?

→ The driver may not be installed correctly if another USB device is active. Discon-

nect your printer, scanner, or other USB device, then try to install the driver again.

→ If the driver for another USB audio device has already been installed, you can use

that driver for the UW10.

●The UW10 does not operate correctly, or no sound is heard.

• Did you install the driver? (page 16)

• Are the USB cable, MIDI cables, and audio cables connected correctly?

(page 13)

• Is the volume setting of the tone generator, playback device, and applica-

tion program set to the appropriate level?

• Have you selected an appropriate device for your audio application?

• Is the sampling frequency set correctly?

→ Refer to the table on page 25.

• Are there wave ﬁles for which the sampling frequency and bit resolution

settings vary?

→ Some audio applications may not simultaneously play wave ﬁles with different

sampling frequencies and bit resolutions.

• (You cannot play a music CD)

→ Check the “Enable digital CD audio for this CD-ROM device” checkbox (page 22).

UW10 Owner’s Manual 31

English

• (You do not hear any sound digitally input from a connected MD or CD player.)

→ Is the SOURCE SELECT switch set correctly? (page 13.)

→ Is the input signal copyright protected? (page 7.)

●The sound is interrupted or distorted.

• Does your computer satisfy the system requirements? (page 10)

• Is any other application or device driver running?

→ Quit all unnecessary application programs.

• Are you playing multiple wave ﬁles?

→ Depending on the computer’s performance, playing multiple wave ﬁles may

cause skipping sound or interrupted playback.

• Have you tried to record or play several minutes of audio data?

→

The processing performance of some computers may decline depending on various fac-

tors, such as the processing speed of audio data, access to an external storage device,

etc. You may be able to improve the performance by changing the settings as follows:

Select [Control Panel | (Sounds and) Multimedia | Audio | Detailed Properties].

Set “Hardware accelerator” to Maximum.

Set “Quality of sampling rate conversion” to Standard.

Select [Control Panel | System | (Hardware) | Device Manager | Disk Drive (or

Hard Disk Controller)].

Select high-speed mode (e.g., DMA mode On).

Upgrade to a higher-speed driver.

For more information on upgrading the driver, visit the web site of the hard disk

manufacturer.

Select [Control Panel | System | (Details) | Performance].

Yamaha recommends that only users with advanced knowledge about computers

change this setting.

Make sure that the file system is correctly set. If the computer has enough

free memory space (more than 128MB) and the size of the wave file to be

recorded or played back is not large, you may be able to improve the

performance by changing the setting for the virtual memory.

Some computers may need updated device drivers (such as a hard disk

controller) or BIOS. For more information, contact the customer support

department or visit the home page of the computer manufacturer.

NOTE

32 UW10 Owner’s Manual

English

●Cannot place the computer in Save Energy (Sleep) mode (or

cancel the mode).

• Is the computer placed in Sleep mode while the audio application is operating?

• Some computers do not feature Sleep mode. In this case, disconnect the

USB cable, then connect it again.

●The recorded level is very low.

• Is the volume level of the computer low?

→ Set the computer’s “Volume Control” to maximum. (page 23.)

• To raise the recording level, record the output from the headphone jack of

an AV device that plays the recording source, and raise the output level as

needed. Alternatively, use the Normalize function after recording.

SOFTWARE LICENSING AGREEMENT

The following is a legal agreement between you, the end user, and Yamaha Corporation

(“Yamaha”). The enclosed Yamaha software program(s) is licensed by Yamaha to the original

purchaser for use only on the terms set forth herein. Please read this licensing agreement with

care. Opening this package indicates that you accept all terms outlined herein. If you do not

agree to the terms, return this package unopened to Yamaha for a full refund.

1. GRANT OF LICENSE AND COPYRIGHT

Yamaha grants you, the original purchaser,

the right to use one copy of the enclosed

software program(s) and data

(“SOFTWARE”) on a single-user computer

system. You may not use it on more than

one computer or computer terminal. The

SOFTWARE is owned by Yamaha and

Yamaha’s licenser(s), and is protected by

Japanese copyright laws and all applicable

international treaty provisions. You are

entitled to claim ownership of the media in

which the SOFTWARE is included.

Therefore, you must treat the SOFTWARE

like any other copyrighted materials.

The SOFTWARE includes a software

program called MidRadio. The MidRadio

involves the TwinVQ technology therein,

the copyright and intellectual property of

which belongs to Nippon Telegraph and

Telephone Corpopation (“NTT”). If the

licensing agreement of the TwinVQ

technology between YAMAHA and NTT

terminates, the ownership of the

MidRadio Player will be assigned from

YAMAHA to NTT.

2. RESTRICTIONS

The SOFTWARE is copyrighted. You may

not engage in reverse engineering or

reproduction of the SOFTWARE by other

conceivable methods. You may not

reproduce, modify, change, rent, lease,

resell, or distribute the SOFTWARE in

whole or in part, or create derivative

works from the SOFTWARE. You may not

transmit or network the SOFTWARE with

other computers. You may transfer

ownership of the SOFTWARE and the

accompanying written materials on a

permanent basis provided that you retain

no copies and the recipient agrees to the

terms of the licensing agreement.

Copyrighted songs obtained by means of

the MidRadio Player are subject to the

following restrictions which you must

observe. Data received by means of the

MidRadio Player may not be used for

commercial purposes. Data received by

means of the MidRadio Player may not be

duplicated, transferred, or distributed, or

played back or performed for an

indeterminate number of listeners without

permission from the copyright owner. The

encryption of data received by means of the

MidRadio Player may not be removed nor

may the electronic watermark be modified

without permission from the copyright

owner. The MidRadio Player may not be

used to distribute illegal data or data that

would violate public ethical standards, nor

may you initiate services based on the use

of the MidRadio Player without permission

from Yamaha Corporation.

3. TERMINATION

The licensing condition of the software

program becomes effective on the day that

you receive the SOFTWARE. If any one of

the copyright laws or clauses of the

licensing conditions is violated, the

licensing agreement shall be terminated

automatically without notice from Yamaha.

In this case, you must destroy the licensed

SOFTWARE and its copies immediately.

4. PRODUCT WARRANTY

Yamaha warrants to the original purchaser

that if the SOFTWARE, when used in normal

conditions, will not perform the functions

described in the manual provided by

Yamaha, the sole remedy will be that

Yamaha will replace any media which

proves defective in materials or

workmanship on an exchange basis without

charge. Except as expressly set forth above,

the SOFTWARE is provided “as is,” and no

other warranties, either expressed or

implied, are made with respect to this

software, including, without limitation the

implied warranties of merchantability and

fitness for a particular purpose.

5. LIMITED LIABILITY

Your sole remedies and Yamaha’s entire

liability are as set forth above. In no event

will Yamaha be liable to you or any other

person for any damages, including

without limitation any incidental or

consequential damages, expenses, lost

profits, lost savings or other damages

arising out of the use or inability to use

such SOFTWARE even if Yamaha or an

authorized dealer has been advised of the

possibility of such damages, or for any

claim by any other party.

6. GENERAL

This license agreement shall be

interpreted according to and governed

by Japanese laws.

SOFTWARE-LIZENZVEREINBARUNG

Die folgende Vereinbarung ist eine rechtsgültige Vereinbarung zwischen Ihnen, dem

Endanwender, und der Yamaha Corporation (“Yamaha”). Yamaha erteilt dem ursprünglichen

Käufer für die beiliegenden Yamaha-Softwareprogramme ausschließlich zu den hier

ausgeführten Bedingungen eine Lizenz zur Verwendung. Bitte lesen Sie diese

Lizenzvereinbarung sorgfältig. Durch das Öffnen dieser Packung bringen Sie zum Ausdruck,

daß Sie alle darin enthaltenen Bedingungen akzeptieren. Wenn Sie nicht mit den

Bedingungen einverstanden sind, können Sie die Packung ungeöffnet an Yamaha

zurückgeben; der Kaufpreis wird in voller Höhe zurückerstattet.

1. ERTEILUNG VON LIZENZ UND

Yamaha erteilt Ihnen, dem ursprünglichen

Käufer, das Recht, jeweils ein Exemplar der

beiliegenden Softwareprogramme und der

darin enthaltenen Daten (“SOFTWARE”) als

Einzelperson auf jeweils einem Computer zu

verwenden. Sie dürfen sie nicht auf mehr

als einem Computer bzw. einer

Computerstation verwenden. Die

SOFTWARE bleibt im Besitz von Yamaha

und dessen Lizenzgebern und ist durch

japanische Copyrightgesetze sowie alle

anwendbaren internationalen

Vertragsbestimmungen geschützt. Sie

haben ein Anspruchsrecht auf das Eigentum

an den Medien, denen die SOFTWARE

beiliegt. Daher müssen Sie die SOFTWARE

wie alle anderen durch Copyright

geschützten Materialien behandeln.

Die SOFTWARE enthält ein

Anwendungsprogramm namens MidRadio.

Das MidRadio beinhaltet die TwinVQ-

Technik und damit das Urheberrecht und

den geistigen Besitz, den die Nippon

Telegraph and Telephone Corporation

(„NTT“) beansprucht. Wenn die

Lizenzvereinbarung der TwinVQ-Technik

zwischen YAMAHA und NTT endet, geht

das Eigentumsrecht für den MidRadio

Player von YAMAHA zurück an NTT.

2. EINSCHRÄNKUNGEN

Die SOFTWARE ist durch Copyright

geschützt. Sie dürfen Sie weder analysieren

noch durch anderweitige Methoden

reproduzieren. Sie dürfen die SOFTWARE

weder ganz noch teilweise reproduzieren,

modifizieren, verändern, gegen Entgelt

oder unentgeltlich verleihen, verkaufen

oder vertreiben, und Sie dürfen auf der

Grundlage der SOFTWARE keine

Ableitungen erstellen. Sie dürfen die

SOFTWARE nicht an andere Computer

senden oder in Netzwerke einspeisen. Sie

dürfen das Eigentum an der SOFTWARE

und den schriftlichen Begleitmaterialien auf

unbefristeter Basis unter den

Voraussetzungen übertragen, daß Sie keine

Kopien zurückbehalten und sich der

Empfänger mit den Bedingungen der

Lizenzvereinbarung einverstanden erklärt.

Urheberrechtlich geschützte Songs, die

durch Einsatz des MidRadio Player

verfügbar gemacht wurden, unterliegen

den folgenden Einschränkungen, die Sie

beachten müssen. Daten, die mittels des

MidRadio Player empfangen wurden,

dürfen nicht für kommerzielle Zwecke

benutzt werden. Daten, die mittels des

MidRadio Player empfangen wurden,

dürfen nicht ohne Erlaubnis des Urhebers

dupliziert, übertragen, oder verbreitet, oder

für eine unbestimmte Anzahl von Zuhörern

abgespielt oder aufgeführt werden. Die

Verschlüsselung von Daten, die mittels des

MidRadio Player empfangen wurden, darf

nicht entfernt werden, noch darf das

elektronische Wasserzeichen ohne Erlaubnis

des Urhebers verändert werden. Der

MidRadio Player darf nicht zur Verbreitung

illegaler Daten oder von Daten benutzt

werden, die öffentliche ethische Standards

verletzen könnten, und Sie dürfen ohne

Erlaubnis der Yamaha Corporation keine

Dienste bereitstellen, die auf der

Verwendung des MidRadio Player basieren.

3. BEENDIGUNG

Die Lizenzbedingungen der

Softwareprogramme werden am Tag, an

dem Sie die SOFTWARE erhalten,

wirksam. Falls ein Copyrightgesetz oder

eine Bestimmung der Lizenzbedingungen

verletzt wird, wird automatisch und ohne

Benachrichtigung durch Yamaha die

Lizenzvereinbarung beendet. In diesem

Fall müssen Sie die lizensierte SOFTWARE

und ihre Kopien unverzüglich vernichten.

4. PRODUKTGARANTIE

Yamaha garantiert dem ursprünglichen

Käufer, daß, falls die SOFTWARE bei

Verwendung unter normalen

Bedingungen nicht die in der von Yamaha

bereitgestellten Anleitung beschriebenen

Funktionen erfüllt, die einzige Abhilfe

darin bestehen wird, daß Yamaha auf

Austauschbasis kostenlos jedes Medium

ersetzen wird, das Material- oder

Verarbeitungsfehler aufweist. Abgesehen

von dem oben Ausgeführten wird die

SOFTWARE “wie die Ware liegt und steht”

geliefert, und es werden keine anderen

ausdrücklichen oder stillschweigenden

Garantien hinsichtlich dieser Software

übernommen, einschließlich, aber nicht

beschränkt auf, die stillschweigenden

Garantien für handelsübliche Qualität und

Eignung für einen bestimmten

Einsatzzweck.

5. BESCHRÄNKTE HAFTUNG

Ihre einzige Abhilfe und die gesamte

Haftung Yamahas bestehen in dem oben

Ausgeführten. Keinesfalls haftet Yamaha

Ihnen oder einer anderen Person gegenüber

für etwaige Schäden, einschließlich, aber

nicht beschränkt auf, zufällige Schäden

oder Folgeschäden, Kosten,

Verdienstausfall, verlorene Ersparnisse oder

andere Schadenersatzansprüche, die aus

der Verwendung der SOFTWARE oder aus

der Tatsache hervorgehen, daß diese

SOFTWARE nicht verwendet werden

konnte, selbst wenn Yamaha oder ein

autorisierter Händler über die Möglichkeit

derartiger Schadenersatzansprüche

informiert wurde, oder für etwaige andere

Ansprüche einer anderen Partei.

6. ALLGEMEINES

Diese Lizenzvereinbarung soll gemäß und

in Übereinstimmung mit den japanischen

Gesetzen ausgelegt werden.

CONTRAT DE LICENCE DE LOGICIEL

Ceci est un contrat entre vous-même, l'utilisateur final, et Yamaha Corporation (« Yamaha »).

Les logiciels Yamaha ci-inclus sont concédés sous licence par Yamaha à l'acheteur original et

ne peuvent être utilisés que dans les conditions prévues aux présentes. Veuillez lire

attentivement ce contrat de licence. Le fait d'ouvrir ce coffret indique que vous acceptez

l'ensemble des termes du contrat. Si vous n'acceptez pas lesdits termes, renvoyez le coffret

non ouvert à Yamaha pour en obtenir le remboursement intégral.

1. CONCESSION DE LICENCE ET DROITS

D’AUTEUR

Yamaha vous concède le droit d’utiliser, en

tant qu’acheteur original, un exemplaire de

chaque logiciel fourni et des données

afférentes à celui-ci (« LOGICIEL ») sur un

ordinateur pour utilisateur unique. Vous

n’êtes pas autorisé à utiliser ces éléments

sur plus d’un ordinateur ou terminal

d’ordinateur. Le LOGICIEL est la propriété

de Yamaha et du (des) détenteur(s) d'une

licence de Yamaha. Il est protégé par les

dispositions relatives au droit d’auteur

contenues dans la législation japonaise et

les traités internationaux. Vous êtes en droit

de revendiquer l’appartenance du support

du LOGICIEL. A ce titre, vous devez traiter

le LOGICIEL comme tout autre élément

protégé par le droit d'auteur.

Le LOGICIEL comprend un programme

appelé MidRadio, qui repose sur la

technologie TwinVQ dont les droits

d'auteur et la propriété intellectuelle

appartiennent à Nippon Telegraph and

Telephone Corporation (« NTT »). Si le

contrat de licence de la technologie

TwinVQ entre YAMAHA et NTT venait à

être résilié, la propriété de MidRadio

Player serait transférée de Yamaha à NTT.

2. RESTRICTIONS

Le LOGICIEL est protégé par le droit

d’auteur. Vous n’êtes pas autorisé à

reconstituer la logique du LOGICIEL ou à

reproduire ce dernier par quelque autre

moyen que ce soit. Vous n’êtes pas en

droit de reproduire, modifier, prêter,

louer, revendre ou distribuer le LOGICIEL

en tout ou partie, ou d’utiliser le

LOGICIEL à des fins de création dérivée.

Vous n’êtes pas autorisé à transmettre le

LOGICIEL à d’autres ordinateurs ou à

l’utiliser en réseau. Vous êtes en droit de

céder, à titre permanent, le LOGICIEL et

la documentation imprimée qui

l’accompagne, sous réserve que vous n’en

conserviez aucun exemplaire et que le

bénéficiaire accepte les termes du présent

contrat.

Les morceaux protégés par le droit

d'auteur obtenus par l'intermédiaire de

MidRadio Player sont soumis aux

restrictions suivantes que vous devez

respecter. Les données reçues par

l'intermédiaire de MidRadio Player ne

doivent pas être utilisées à des fins

commerciales. Les données reçues par

l'intermédiaire de MidRadio Player ne

peuvent pas être dupliquées, transférées,

distribuées, reproduites ou exécutées pour

le compte d'un nombre indéterminé

d'auditeurs sans la permission du

propriétaire du droit d'auteur. Le cryptage

des données reçues par l'intermédiaire de

MidRadio Player ne peut pas être

supprimé ni le filigrane électronique

modifié sans la permission du propriétaire

du droit d'auteur. MidRadio Player ne peut

pas être utilisé pour distribuer des

données illégales ou des données

susceptibles de porter outrage aux mœurs,

de même qu'il est interdit de proposer des

services basés sur MidRadio Player sans la

permission de Yamaha Corporation.

3. RESILIATION

Les conditions énoncées dans le présent

contrat de licence prennent effet à

compter du jour où le LOGICIEL vous est

remis. Si l’une quelconque des dispositions

relatives au droit d’auteur ou des clauses

du contrat ne sont pas respectées, le

contrat de licence sera résilié de plein droit

par Yamaha, ce sans préavis. Dans ce cas,

vous devrez immédiatement détruire le

LOGICIEL concédé sous licence ainsi que

les copies réalisées.

4. GARANTIE PRODUIT

Si, dans des conditions normales

d’utilisation, le LOGICIEL ne remplit pas

les fonctions décrites dans le manuel

fourni, Yamaha s’engage vis à- vis de

l’acheteur original à remplacer

gratuitement, sur la base d’un échange,

tout support reconnu défectueux par

suite d’un défaut de matière première ou

d’un vice de fabrication. Ceci constitue le

seul recours opposable à Yamaha. Hormis

dans les cas expressément énoncés plus

haut, le LOGICIEL est livré « en l’état » et

toute autre garantie expresse ou implicite

le concernant, y compris, de manière non

limitative, toute garantie implicite de

qualité marchande et d’adéquation à un

usage particulier, est exclue.

5. RESPONSABILITE LIMITEE

Votre unique recours et la seule

responsabilité de Yamaha sont tels

qu’énoncés précédemment. En aucun cas

Yamaha ne pourra être tenu responsable,

par vous-même ou une autre personne,

de quelques dommages que ce soit,

notamment et de manière non limitative,

de dommages indirects, frais, pertes de

bénéfices, pertes de fonds ou d’autres

dommages résultant de l’utilisation ou de

l’impossibilité d’utiliser le LOGICIEL,

même si Yamaha ou un distributeur agréé

ont été prévenus de l’éventualité de tels

dommages, ou de quelque autre

revendication formulée par une tierce

partie.

6. REMARQUE GENERALE

Le présent contrat de licence est régi par

le droit japonais, à la lumière duquel il

doit être interprété.

• This applies only to products distributed by Yamaha Canada Music Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.

CANADA

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

(class B)

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT

MODIFY THIS UNIT!

This product, when installed as indi-

cated in the instructions contained in

this manual, meets FCC require-

ments. Modifications not expressly

approved by Yamaha may void your

authority, granted by the FCC, to use

the product.

2. IMPORTANT: When connecting this

product to accessories and/or another

product use only high quality shielded

cables. Cable/s supplied with this

product MUST be used. Follow all

installation instructions. Failure to

follow instructions could void your

FCC authorization to use this product

in the USA.

3. NOTE: This product has been tested

and found to comply with the

requirements listed in FCC

Regulations, Part 15 for Class “B”

digital devices. Compliance with these

requirements provides a reasonable

level of assurance that your use of this

product in a residential environment

will not result in harmful interference

with other electronic devices. This

equipment generates/uses radio

frequencies and, if not installed and

used according to the instructions

found in the users manual, may cause

interference harmful to the operation

of other electronic devices.

Compliance with FCC regulations

does not guarantee that interference

will not occur in all installations. If this

product is found to be the source of

interference, which can be determined

by turning the unit “OFF” and “ON”,

please try to eliminate the problem by

using one of the following measures:

Relocate either this product or the

device that is being affected by the

interference.

Utilize power outlets that are on differ-

ent branch (circuit breaker or fuse)

circuits or install AC line filter/s.

In the case of radio or TV interfer-

ence, relocate/reorient the antenna. If

the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to co-axial

type cable.

If these corrective measures do not

produce satisfactory results, please

contact the local retailer authorized to

distribute this type of product. If you

can not locate the appropriate retailer,

please contact Yamaha Corporation of

America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park,

CA90620

The above statements apply ONLY to

those products distributed by Yamaha

Corporation of America or its

subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à

Yamaha ou au distributeur le plus proche de vous ﬁgurant dans

la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweili-

gen Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más

cercana o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif.

90620, U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de Mexico S.A. De C.V.,

Departamento de ventas

Javier Rojo Gomez No.1149, Col. Gpe Del

Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.

Tel: 686-00-33

BRAZIL

Yamaha Musical do Brasil LTDA.

Av. Rebouças 2636, São Paulo, Brasil

Tel: 011-853-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Viamonte 1145 Piso2-B 1053,

Buenos Aires, Argentina

Tel: 1-4371-7021

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización

Marbella, Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

IRELAND

Danfay Ltd.

61D, Sallynoggin Road, Dun Laoghaire,

Co. Dublin

Tel: 01-2859177

GERMANY

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen,

Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Central Europe GmbH,

Branch Switzerland

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Central Europe GmbH,

Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

THE NETHERLANDS

Yamaha Music Central Europe,

Branch Nederland

Clarissenhof 5-b, 4133 AB Vianen, The

Netherlands

Tel: 0347-358 040

BELGIUM/LUXEMBOURG

Yamaha Music Central Europe GmbH,

Branch Belgium

Rue de Geneve (Genevastraat) 10, 1140 -

Brussels, Belgium

Tel: 02-726 6032

FRANCE

Yamaha Musique France, S.A.

Division Professionnelle

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha-Hazen Música, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

GREECE

Philippos Nakas S.A. The Music House

147 Skiathou Street, 112-55 Athens, Greece

Tel: 01-228 2160

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1

Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 8B

DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

F-Musiikki Oy

Kluuvikatu 6, P.O. Box 260,

SF-00101 Helsinki, Finland

Tel: 09 618511

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1

N-1345 Østerås, Norway

Tel: 67 16 77 70

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120

IS-128 Reykjavik, Iceland

Tel: 525 5000

OTHER EUROPEAN COUNTRIES

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen,

Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan

430-8650

Tel: +81-53-460-2312

TURKEY/CYPRUS

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen,

Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LB21-128 Jebel Ali Freezone

P.O.Box 17328, Dubai, U.A.E.

Tel: +971-4-881-5868

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 2737-7688

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend.

Gatot Subroto Kav. 4, Jakarta 12930, Indo-

nesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

Tong-Yang Securities Bldg. 16F 23-8

Yoido-dong, Youngdungpo-ku, Seoul, Korea

Tel: 02-3770-0661

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-703-0900

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885

MCPO, Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music Asia Pte., Ltd.

11 Ubi Road #06-00, Meiban Industrial

Building, Singapore

Tel: 65-747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

121/60-61 RS Tower 17th Floor,

Ratchadaphisek RD., Dindaeng,

Bangkok 10320, Thailand

Tel: 02-641-2951

THE PEOPLE’S REPUBLIC OF CHINA

AND OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan

430-8650

Tel: +81-53-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

NEW ZEALAND

Music Houses of N.Z. Ltd.

146/148 Captain Springs Road, Te Papapa,

Auckland, New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan

430-8650

Tel: +81-53-460-2312

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2445

SY29

USB-AUDIO INTERFACE

Owner's Manual

Bedienungsanleitung

Mode d'emploi

This document is printed on recycled chlorine

free (ECF) paper with soy ink.

Auf Recycling-Umweltpapier gedruckt.

Ce document a été imprimé sur du papier recyclé

non blanchi au chlore.

M.D.G., Pro Audio & Digital Musical Instrument Division,

Yamaha Corporation

305AP-01A0 Printed in China

Yamaha Web Site (English only)

www.yamahasynth.com

Yamaha Manual Library

http://www2.yamaha.co.jp/manual/english/

USB-AUDIO INTERFACE

EnglishDeutschFrançais

Yamaha UW10 de handleiding

Merk: Yamaha

Model: UW10

Type: de handleiding

Download PDF

rapport

in andere talen

English: Yamaha UW10 Owner's manual
italiano: Yamaha UW10 Manuale del proprietario
русский: Yamaha UW10 Инструкция по применению
français: Yamaha UW10 Le manuel du propriétaire
español: Yamaha UW10 El manual del propietario
Deutsch: Yamaha UW10 Bedienungsanleitung
português: Yamaha UW10 Manual do proprietário
dansk: Yamaha UW10 Brugervejledning
suomi: Yamaha UW10 Omistajan opas
čeština: Yamaha UW10 Návod k obsluze
svenska: Yamaha UW10 Bruksanvisning
Türkçe: Yamaha UW10 El kitabı
polski: Yamaha UW10 Instrukcja obsługi
română: Yamaha UW10 Manualul proprietarului

Yamaha UW10 de handleiding

Yamaha UW10 de handleiding

in andere talen

Gerelateerde artikelen

Andere documenten