Yamaha MOXF6 Handleiding

Merk: Yamaha

Model: MOXF6

Categorie: Synthesizer

Type: Handleiding

Deze handleiding is ook geschikt voor

Owner’s Manual

MOXF6/MOXF8 Owner’s Manual

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply (adapter). DO

NOT connect this product to any power supply or adapter other than one

described in the manual, on the name plate, or specifically recom-

mended by Yamaha.

WARNING: Do not place this product in a position where anyone

could walk on, trip over, or roll anything over power or connecting cords

of any kind. The use of an extension cord is not recommended! If you

must use an extension cord, the minimum wire size for a 25’ cord (or

less) is 18 AWG. NOTE: The smaller the AWG number, the larger the

current handling capacity. For longer extension cords, consult a local

electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at the

time of printing. However, Yamaha reserves the right to change or mod-

ify any of the specifications without notice or obligation to update existing

units.

This product, either alone or in combination with an amplifier and head-

phones or speaker/s, may be capable of producing sound levels that

could cause permanent hearing loss. DO NOT operate for long periods

of time at a high volume level or at a level that is uncomfortable. If you

experience any hearing loss or ringing in the ears, you should consult an

audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory mounting

fixtures that are either supplied with the product or as optional accesso-

ries. Some of these items are designed to be dealer assembled or

installed. Please make sure that benches are stable and any optional fix-

tures (where applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are not

covered by the manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and consult your dealer

before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and environ-

mentally friendly. We sincerely believe that our products and the produc-

tion methods used to produce them, meet these goals. In keeping with

both the letter and the spirit of the law, we want you to be aware of the

following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of bat-

tery is approximately five years. When replacement becomes necessary,

contact a qualified service representative to perform the replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, never mix old batteries with new ones, and

never mix different types of batteries. Batteries MUST be installed cor-

rectly. Mismatches or incorrect installation may result in overheating and

battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all batter-

ies away from children. Dispose of used batteries promptly and as regu-

lated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some reason

its useful life is considered to be at an end, please observe all local,

state, and federal regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc. If your dealer is unable to assist

you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model num-

ber, serial number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and the date of pur-

chase in the spaces provided below and retain this manual as a perma-

nent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

This product contains a high intensity lamp that contains

a small amount of mercury. Disposal of this material may

be regulated due to environmental considerations.

For disposal information in the United States, refer to the

Electronic Industries Alliance web site:

www.eiae.org

(mercury)* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

MOXF6/MOXF8 Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

(weee_eu_en_01)

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products

should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with

your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste disposal

service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer

and ask for the correct method of disposal.

(standby)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif.

90620

Telephone : 714-522-9011

Type of Equipment : MUSIC PRODUCTION SYNTHESIZER

Model Name : MOXF6, MOXF8

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including

interference that may cause undesired operation.

See user manual instructions if interference to radio reception is

suspected.

(FCC DoC)

The model number, serial number, power requirements, etc., may be

found on or near the name plate, which is at the bottom of the unit.

You should note this serial number in the space provided below and

retain this manual as a permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

(bottom_en_01)

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så länge som

den ar ansluten till vägguttaget, även om själva apparaten har

stängts av.

ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt,

sålænge netledningen sidder i en stikkontakt, som er tændt — også

selvom der er slukket på apparatets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko

laitetta verkosta.

MOXF6/MOXF8 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or

radiators. Also, do not excessively bend or otherwise damage the

cord, or place heavy objects on it.

• Only use the voltage specified as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

• Use the specified adaptor (page 73) only. Using the wrong adaptor

can result in damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the

instrument or attempt to disassemble or modify the internal

components in any way. If it should appear to be malfunctioning,

discontinue use immediately and have it inspected by qualified

Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or

wet conditions, place on it any containers (such as vases, bottles or

glasses) containing liquids which might spill into any openings. If

any liquid such as water seeps into the instrument, turn off the

power immediately and unplug the power cord from the AC outlet.

Then have the instrument inspected by qualified Yamaha service

personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning

item may fall over and cause a fire.

• When one of the following problems occur, immediately turn off the

power switch and disconnect the electric plug from the outlet. (If you

are using batteries, remove all batteries from the instrument.) Then

have the device inspected by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a

multiple-connector. Doing so can result in lower sound quality, or

possibly cause overheating in the outlet.

• When removing the electric plug from the instrument or an outlet,

always hold the plug itself and not the cord. Pulling by the cord can

damage it.

• Remove the electric plug from the outlet when the instrument is not

to be used for extended periods of time, or during electrical storms.

• Do not place the instrument in an unstable position where it might

accidentally fall over.

•B

efore moving the instrument, remove all connected cables, to prevent

damage to the cables or injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction occurs,

immediately turn off the power switch and disconnect the plug from

the outlet. Even when the power switch is turned off, electricity is

still flowing to the product at the minimum level. When you are not

using the product for a long time, make sure to unplug the power

cord from the wall AC outlet.

• Before connecting the instrument to other electronic components,

turn off the power for all components. Before turning the power on

or off for all components, set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum

levels and gradually raise the volume controls while playing the

instrument to set the desired listening level.

Power supply/AC power adaptor

Location

Connections

DMI-5 1/2

MOXF6/MOXF8 Owner’s Manual

• Never insert or drop paper, metallic, or other objects into the gaps

on the panel or keyboard. This could cause physical injury to you or

others, damage to the instrument or other property, or operational

failure.

• Do not rest your weight on, or place heavy objects on the

instrument, and do not use excessive force on the buttons, switches

or connectors.

• Do not use the instrument/device or headphones for a long period of

time at a high or uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing loss or

ringing in the ears, consult a physician.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (display

is off), electricity is still flowing to the instrument at the minimum

level.

When you are not using the instrument for a long time, make sure you

unplug the power cord from the wall AC outlet.

Make sure to discard used batteries according to local regulations.

NOTICE

o avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices

below.

 Handling and Maintenance

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or

radio may generate noise.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the

day) to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation.

• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.

 Saving data

• The data in the instrument’s Edit Buffer (memory location for edited data) will be lost when it is turned off. Save your important data to the user

memory, a USB flash memory device or external device such as a computer. Keep in mind that saved data may be lost due to malfunction or

incorrect operation.

• To protect against data loss due to media damage, we recommend that you save your important data onto two USB flash memory devices/external

media.

Information

 About copyrights

• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your

personal use.

• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license

to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical

scores and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws.

Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

 About functions/data bundled with the instrument

• This device is capable of using various types/formats of music data by optimizing them to the proper format music data for use with the device in

advance. As a result, this device may not play them back precisely as their producers or composers originally intended.

 About this manual

• The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different from those on

your instrument.

• Windows is a registered trademark of Microsoft

Corporation in the United States and other countries.

• Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Handling caution

Yamaha cannot be held responsible for damage caused by

improper use or modifications to the instrument, or data that is

lost or destroyed.

About the latest Firmware Version

Yamaha may from time to time update firmware of the product and the other associated software without notice for improvement. We

recommend that you check our web site for the latest releases and upgrade your firmware of the MOXF6/MOXF8 or the associated

software.

http://download.yamaha.com/

Note that the explanations in this Owner’s Manual apply to the version of firmware when this Owner’s Manual was produced. For details

about additional functions included in later releases, refer to the above website.

DMI-5 2/2

MOXF6/MOXF8 Owner’s Manual

A message from the MOXF6/MOXF8

Development Team

Thank you for purchasing the Yamaha MOXF6/MOXF8 Music Production Synthesizer.

We, as the development team, have designed this instrument

so that players of every genre and level can easily enjoy truly high-quality sounds and

advanced functions in creating and performing music.

SOUND

Extraordinarily high-quality sound for a variety of applications

The MOXF6/MOXF8 draws on the high-quality sound of the famed MOTIF XF, used extensively by artists worldwide,

and is equipped with a wide range of dynamic sounds for use in virtually any music application.

urthermore, in one of the most important advantages of the MOXF, an optional Flash Memory Expansion Board can be installed.

This feature was included in response to many and repeated requests from power users. Now, Sample (audio) data remains on

the board, even when the power is turned off—allowing you to instantly use Waveforms containing Samples when

you turn the power back on, without the need to load them from an external USB storage device.

FUNCTIONS

Instant, smooth translation from inspiration to final music composition

The MOXF6/MOXF8 features a powerful Performance Creator function which lets you combine your favorite Voice with

other Voices and drum parts, and perform with full rhythmic and chordal backing. You can also record your performances

as a Song or Pattern, simply by pressing the [REC] button from Performance mode—and then, after recording,

automatically move to the Song/Pattern mode for further editing, refining and completing the Song or Pattern.

This workflow is exceptionally smooth and transparent, and lets you create music quickly and easily as the inspiration hits.

Seamless music production with Cubase

The MOXF6/MOXF8 were developed giving maximum consideration to integration with the Cubase series DAW software made by

Steinberg. We’ve enhanced and strengthened the remote control function in connection with Cubase,

letting you easily and conveniently control optional parameters on Cubase with the AI KNOB,

or by using control templates compatible with various VST instruments to easily control multiple parameters and

complex operations on software synthesizers directly from your hardware synthesizer keyboard.

DESIGN

Stylish design and professional look

We also designed the stylish exterior to reflect the professional-level sounds and sophisticated features of the MOXF6/MOXF8,

making it an instrument you’ll love to play, and one you’ll feel proud in showing off onstage.

Moreover, its value as a live performance instrument is made even greater by its portability.

We also took particular care in designing the size and external appearance to make it easy to use,

even when combined in a computer music system.

MOXF6/MOXF8 Owner’s Manual

Accessories

•AC adaptor*

• USB cable

• Owner’s Manual (this book)

• Online Manual CD-ROM x 1 (Reference Manual, Synthesizer Parameter Manual, and Data List)

• CUBASE AI DOWNLOAD INFORMATION

* May not be included in your area. Please check with your Yamaha dealer.

Using the MOXF6/MOXF8 Manuals

Your MOXF6/MOXF8 synthesizer comes with four different reference guides—the Owner’s Manual (this book), the Reference

Manual, the Synthesizer Parameter Manual, and the Data List. While the Owner’s Manual is packaged together with the

synthesizer as a hardcopy booklet, this Reference Manual, Synthesizer Parameter Manual, and the Data List are provided as

PDF documents on the bundled CD-ROM.

• Owner’s Manual (this book)

Describes how to set up your MOXF6/MOXF8 and how to perform basic operations.

• Reference Manual (this PDF document)

Describes the internal design of your MOXF6/MOXF8 and the various parameters that can be adjusted and set. It also

describes how to use the instrument in specific applications and provides the following reference materials.

• Category lists for the Voices and Performances

• Setting examples of the Controller Destination

• Functions of Knobs 1 – 8 in Voice mode and Mixing mode

• Song playback types

• Song Track Loop—setting example

• Punch In/Out recording in Song mode

• Pattern playback types

• Pattern Loop recording

• Creating an Arpeggio

• Storing the Mixing settings as a Mixing Template

• Remote control assignments

• File/Folder selection in File mode

• Playing back SMF (Standard MIDI file) data from USB flash memory device

• Formatting a USB flash memory device

• Synthesizer Parameter Manual (PDF document)

This general, cross-product document explains the Voice parameters, effect types, effect parameters, and MIDI

messages that are used for all synthesizers incorporating the Yamaha AWM2 tone generators. Read the Owner’s

Manual and Reference Manual first and then use this parameter manual if necessary to learn more about parameters

and terms that relate to Yamaha synthesizers in general.

• Data List (PDF document)

Provides lists such as the Voice List, Waveform List, Performance List, Effect Type List, Arpeggio Type List, as well as

reference materials such as the MIDI Implementation Chart and Remote Control Function List.

How to use the PDF manuals

The Reference Manual, the Synthesizer Parameter Manual, and the Data List are provided as data documents in PDF format. These

PDF files can be viewed and read on a computer. When using Adobe

Reader

to view a PDF file, you can search for specific

words, print a specific page or link to open a desired section in the manual. The term search and link functions are especially

convenient methods of navigating through a PDF file, and we recommend that you use them. The latest version of Adobe Reader

can be downloaded from the following URL.

http://www.adobe.com/products/reader

MOXF6/MOXF8 Owner’s Manual

MOXF6/MOXF8 Main Features

 MOTIF XF Sound Engine feature

The wide range of dynamic and authentic MOTIF XF waveforms (such as the realistic sounds of acoustic piano,

electric piano, synthesizer, strings, wind instruments, drums) are all included in this instrument. The sophisticated XA

(Expanded Articulation) function has also been included, providing greater performance flexibility and acoustic

realism. It allows you to more effectively recreate realistic sound and natural performance techniques—such as

legato and trills—and provides other unique modes for random and alternate sound changes as you play. Moreover,

the instrument features new Arpeggio types for Drum Voices, as well as the existing MOTIF XF Arpeggio types, plus

an extensive effect system—including VCM (Virtual Circuitry Modeling) Effects, Master Effect, and Master EQ. In a

wide variety of ways, the MOXF6/MOXF8 truly enhances your music performance and creation.

 Easy-to-use user interface

You can select a desired Voice or Performance directly by using the sixteen number buttons. You can also call up

desired Voices or Performances according to the instrument type by using the Category Search function. This

instrument also provides a powerful, easy-to-use Performance Creator function, which lets you quickly and smoothly

create fully realized music, whenever the inspiration strikes you. Use it to easily create new Performances by using

favorite Voices you’ve found in the Voice mode.

 Comprehensive sequencer for creating Songs and Patterns

This instrument features a built-in sequencer which enables you to produce high-quality music, without the need of a

computer or any other devices. The sequencer features both Realtime recording, which records your performance

data as you play it, and Step recording, which is suitable for recording precise, mechanical phrases or other difficult-

to-execute passages. Moreover, you can record the Performance as a Song/Pattern simply by pressing the [REC]

button, and easily edit and refine your song to completion.

 Optional Flash Memory Expansion Module

The MOXF provides the option of installing a Flash Memory Expansion Module (FL512M/FL1024M), allowing you to

internally store Waveforms that include your sampled audio sounds, and keep those Waveforms intact, even when

turning off the power.

 Responsive, expressive keyboard

The MOXF8 features an 88-key GHS keyboard. This feature provides authentic, realistic keyboard response—much

like the playing feel of an acoustic piano—with the lower keys being heavy in touch, the higher keys light, and all the

natural gradations in between. The MOXF6 features a newly developed, 61-key, semi-weighted keyboard. The

keyboard has been designed and adjusted so that you easily and expressively play the rich variety of sounds of the

instrument.

 Master Keyboard function

This convenient function lets you use this instrument as a master keyboard controller (with independent Zones), and

for easily reconfiguring the instrument between Voice/Performance play and Song/Pattern play in live applications.

 Stereo A/D INPUT [L]/[R] jacks

You can also connect various devices, such as microphone, guitar, or audio equipment, to the Input jacks of the

instrument, and have that audio input signal sound as a separate A/D input Part in the Voice/Performance/Song/

Pattern mode. Various parameters such as volume, pan, and effect can be set for this Part, and the sound is output

together with all the other Parts, letting you play and output the sound MOXF6/MOXF8 together with the external

sound. Also, you can create a vocoder sound by using the input signal from these jacks and the internal effect.

 USB Audio/MIDI interface

The USB terminal of the instrument serves as both a MIDI and audio interface—letting you record digitally the

instrument sound and the audio signal from the A/D INPUT [L]/[R] jacks to DAW software on a computer. You can also

output both the instrument sound and the DAW software input signal from the MOXF6/MOXF8.

 Integration with Cubase

The MOXF is specially designed to work seamlessly with Cubase, Steinberg’s full-featured DAW software — giving

you a comprehensive, all-in-one music production system, in which hardware and software are fully integrated.

MOXF6/MOXF8 Owner’s Manual

A message from the MOXF6/MOXF8 Development Team ...6

Accessories ...........................................................................7

Using the MOXF6/MOXF8 Manuals ......................................7

MOXF6/MOXF8 Main Features.............................................8

Control and Functions 10

Top Panel ............................................................................10

Rear Panel...........................................................................16

Setting Up 17

Power supply.......................................................................17

Connecting speakers or headphones..................................17

Powering up the system ......................................................17

Auto Power Off function.......................................................18

Adjusting the volume and the brightness of the display ......18

Starting up ...........................................................................19

Selecting programs..............................................................19

Playing the Demo Songs .....................................................19

Resetting User Memory to the initial factory settings ..........20

Basic Operation 21

Moving the cursor................................................................21

Changing (editing) parameter values ..................................21

Functions and Sub-Functions..............................................21

Inputting a number directly ..................................................21

Naming (inputting characters) .............................................22

Selecting a note type...........................................................22

Note (Key) and Velocity settings .........................................22

Quick Guide 23

Modes..................................................................................23

Basic Instructions ................................................................24

Playing the keyboard in the Voice mode .............................25

Selecting a Preset Voice ...........................................................25

Using the Category Search function ......................................... 26

Grouping your most-used Voices together—

Favorite Category......................................................................26

Using the Arpeggio function ..................................................... 27

Turning the Arpeggio On/Off.............................................. 27

Changing the Arpeggio type..............................................27

Keyboard Octave/Transpose setting ........................................ 27

Changing the tonal qualities of the Voice ................................. 28

Editing a Voice ..........................................................................28

Enhancing the sound with Effects............................................. 29

Changing the Arpeggio Type assignment ................................ 31

Creating a new Performance by using your favorite Voice

(Performance Creator).........................................................31

Layer—Playing different Voices together.................................. 31

Split—Playing two different Voices with your left and

right hands ................................................................................ 32

Drum Assign—Layering a drum Part with the current Voice.....33

Changing the drum pattern (Arpeggio Type)............................33

Playing the keyboard in the Performance Mode..................34

Selecting a Performance........................................................... 34

Changing the timbre of the Voice ............................................. 35

Recording in the Performance mode .................................. 36

Song and Pattern ...................................................................... 36

Recording the melody and Arpeggio playback to the Song .... 36

Recording Arpeggio playback to a Pattern .............................. 37

Connecting a microphone or audio equipment ................... 38

Playing the keyboard along with the sound input from

the A/D INPUT [L]/[R] jacks ...................................................... 38

Playing the keyboard along with Vocoder ................................ 39

Creating an original Song ................................................... 40

Song playback .......................................................................... 41

Creating a Drum part via Step Recording................................. 41

Creating a bass part via Realtime Recording ........................... 43

Creating a synthesizer part by using Arpeggio ........................ 44

Correcting wrong notes............................................................. 45

Completing the Song by editing the Mixing.............................. 45

Storing the created Song .......................................................... 46

Creating an original Pattern................................................ 47

Listening to the Demo Patterns ................................................. 47

Creating a Pattern (Section A) by using Arpeggio.................... 47

Creating another Pattern (Section B) by

using already recorded data..................................................... 48

Creating a Pattern Chain for converting to a Song ................... 49

Connecting external MIDI instruments................................ 51

Using a Connected Computer ............................................ 53

Connecting to a computer ........................................................ 53

Creating a Song with a computer ............................................. 54

Remote-controlling the software from the MOXF6/MOXF8

(Remote mode) ......................................................................... 55

Using the MOXF6/MOXF8 Editor............................................... 57

Using as a Master Keyboard .............................................. 57

Registering the Edited Voice/Performance/Song/Pattern ......... 57

Making settings for use as a master keyboard ......................... 58

Making Global System Settings (Utility Mode).................... 58

Setting the default mode when turning the power on ............... 58

Reversing the LCD status ......................................................... 59

Click (metronome) settings ....................................................... 59

Effect settings applied to the signal input from

the A/D INPUT jack ................................................................... 59

Master Effect/Master EQ settings in the Voice mode................ 59

Transmitting Control Change messages using

the Foot Switch.......................................................................... 59

Saving/Loading Data (File Mode) ....................................... 60

Saving the settings to a USB flash memory device .................. 60

Loading the settings from a USB flash memory device............ 60

Precautions when using the USB [TO DEVICE] terminal .......... 61

Appendix 62

Shift Function List ............................................................... 62

Display Messages............................................................... 63

Troubleshooting .................................................................. 65

Installing Optional Hardware............................................... 70

Available devices...................................................................... 70

Installation locations.................................................................. 70

Installation Precautions ............................................................. 70

Installing Optional Hardware FL512M/FL1024M....................... 71

Removing the Module ............................................................... 72

Specifications...................................................................... 73

Index ................................................................................... 74

Contents

MOXF6/MOXF8 Owner’s Manual

Top Panel

MOXF8

MOXF6

Control and Functions

A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 C2 C3

C1 D1 E1 F1 G1 A1 B1 C2 C3

MOXF6/MOXF8 Owner’s Manual

Control and Functions

C4 C5 C6 C7

C4 C5 C6

MOXF6/MOXF8 Owner’s Manual

Control and Functions

Keyboard

The MOXF8 features an 88-key keyboard, while the MOXF6

has 61 keys. All are equipped with a touch response feature,

initial touch. With initial touch, the instrument senses how

strongly or softly you play the keys, and uses that playing

strength to affect the sound in various ways, depending on

the selected Voice.

Pitch Bend wheel

Controls the pitch bend effect. You can also assign other

functions to this controller.

Modulation wheel

Controls the modulation effect. You can also assign other

functions to this controller.

[MASTER VOLUME] slider (page 18)

Adjusts the volume of the overall sound. Move the slider

upwards to raise the output level from the OUTPUT [L/MONO]/

[R] jacks and the [PHONES] jack.

[DAW LEVEL] slider

Adjusts the volume of the audio signal input from the USB

[TO HOST] terminal.

A/D INPUT [GAIN] knob (page 39)

Use this to adjust the input gain of the audio signals at the A/

D INPUT [L]/[R] jacks. Depending on the connected

microphone, you may need to adjust this for optimum level.

The volume level is increased as the knob is rotated to the

right and decreased as it is rotated to the left.

NOTE Depending on the output level of the equipment connected to

the A/D INPUT [L]/[R] jacks, you should change the value of the

Mic/Line parameter in the [F1] GENERAL display of the Utility

mode. When the output level of the connected equipment (such

as a microphone, guitar, bass) is low, set this parameter to “mic.”

When the output level of the connected equipment (such as a

synthesizer keyboard, CD player) is high, set this parameter to

“line.”

A/D INPUT [ON/OFF] button (page 39)

Switches whether or not this instrument accepts the audio

signal input via the A/D INPUT [L]/[R] jack.

[LEVEL] meter button (page 39)

Selects the destination signal controlled via the [LEVEL]

meter, input signal via the A/D INPUT [L]/[R] jacks or output

signal via the OUTPUT [L/MONO]/[R] jack.

[LEVEL] meter (page 39)

Indicates the level of the signal specified via the [LEVEL]

meter switch button.

Knob Function 1 button

Pressing this button changes the functions assigned to Knobs

1 – 4 (on the upper row). The lamp next to the currently active

parameters will light. In the Voice mode, the function of each

knob is applied to the current Voice; in the Performance/Mixing

mode, the function of each knob is applied only to the currently

selected Part or to all Parts (depending on the setting via the

[COMMON] and [PART SELECT] buttons).

NOTE When you press the Knob Function 1 button while holding the

[SHIFT] button, the lamp next to the [TONE 1] button will light

and the TONE 1 parameters are assigned to Knobs 1 – 4.

Knob Function 2 button

Pressing this button changes the functions assigned to

Knobs 5 – 8 (on the lower row). The lamp next to the currently

active parameters will light.

NOTE When you press the Knob Function 2 button while holding the

[SHIFT] button, the lamp next to the [EQ] button will light and the

EQ parameters are assigned to Knobs 5 – 8.

Knobs 1 – 8 (page 28)

These eight highly versatile knobs let you adjust various

aspects or parameters of the current Voice. In this manual,

the knobs on the upper row are called “Knob 1” – “Knob 4”

and the knobs on the lower row are called “Knob 5” – “Knob

8.” Pressing the Knob Function 1 button will change the

functions of Knobs 1 – 4 while pressing the Knob Function 2

button will change the functions of Knobs 5 – 8.

ASSIGNABLE FUNCTION [1]/[2] buttons

Depending on the XA (Expanded Articulation) settings in the

Voice Element Edit mode, you can call up the specific

Element of the selected Voice by pressing each of these

buttons during your keyboard performance. In addition, you

can assign other functions to these buttons.

OCTAVE [-] and [+] buttons (page 27)

Use these buttons to change the note range of the keyboard.

To restore the normal octave setting, press both buttons

simultaneously.

MOXF6/MOXF8 Owner’s Manual

Control and Functions

TRANSPOSE [-] and [+] buttons (page 27)

Use these buttons to raise or lower the pitch of the note in

semitone steps. To restore the normal octave setting, press

both buttons simultaneously.

EFFECT buttons

The extensive effect block of the instrument provides Insertion

Effects (eight sets), System Effects (Reverb and Chorus),

and Master Effects. The effects can be applied to the

keyboard played Voices and to Song/Pattern playback.

When the lamp of the [INSERTION], [SYSTEM] or [MASTER]

button is turned on, the corresponding Effect is available.

NOTE When the Reverb/Chorus of the “SystemFXOn/OffBtn” parameter

is set to off in the [UTILITY]  [F1] GENERAL  [SF1] TG

display, the Reverb/Chorus will not function even if the EFFECT

[SYSTEM] button is turned off.

ARP [ON/OFF] button (page 27)

Press this button to enable or disable playback of the

Arpeggio for each Voice, Performance, Song, or Pattern. If

the Arpeggio Switch of the selected Part is set to off in the

Performance/Song/Pattern mode, however, pressing this

button has no effect.

ARP [EDIT] button (page 31)

Press this button to call up the Arpeggio Edit display of the

Voice/Performance /Song/Pattern mode. When the Arpeggio

Edit display is shown with the [E] (Edit indicator) called up

by editing a parameter, press the ARP [EDIT] button (the

lamp flashes) to call up the Compare status. This restores

the original, unedited setting. In the Compare status, the [E]

indication is replaced by [C]. Press the ARP [EDIT] button

again to exit from the Compare status.

[DAW REMOTE] button (page 55)

Turn on this button to enter the Remote mode. The Remote

mode lets you control DAW software on your computer from

the panel controls of the instrument.

SEQ TRANSPORT

button (page 19)

These buttons control recording and playback of the Song/

Pattern sequence data.

[P] (Top) button

Instantly returns to the beginning of the current Song or

Pattern (i.e., the first beat of the first measure).

[G] (Reverse) button

Press briefly to move back one measure at a time, or

hold to continuously rewind.

[H] (Forward) button

Press briefly to move forward one measure at a time, or

hold to continuously fast-forward.

[REC] (Record) button

Press this to enable recording (Song or Pattern phrase).

(The indicator lights.)

[J] (Stop) button

Press to stop recording or playback.

[F] (Play) button

Press to start playback/recording from the current point

in the Song or Pattern. During recording and playback,

the indicator flashes at the current tempo.

LCD (Liquid Crystal Display)

The backlit LCD indicates the parameters and values related

to the currently selected operation or mode.

[F1] – [F6] (Function) buttons (page 21)

These buttons located directly below the LCD call up the

corresponding functions indicated in the display.

[SF1] – [SF6] (Sub Function) buttons

(page 21)

These buttons located directly below the display call up the

corresponding sub functions indicated in the display. These

buttons can be also used to call up different Arpeggio types

in some displays of the Play mode and Record mode

(page 27). These buttons can be also used as Song Scene

buttons in Song Play/Song Record (see the “Reference

Manual” PDF document).

MOXF6/MOXF8 Owner’s Manual

Control and Functions

[CATEGORY SEARCH] button (page 26)

In the Voice/Performance Part Edit/Song/Pattern mode, turn

this button on to call up the Category Search display of the

Voice assigned to the current Part. In this status, the [A] – [H]

buttons can be used for selecting the Main Category of the

Voice.

In the Performance mode (except for the Part Edit mode), turn

on this button to call up the Category Search display of the

current Performance. In this status, the [A] – [H] buttons can

be used for selecting the Main Category of the Performance.

[FAVORITE] button

Use this convenient function to store all your favorite, often-

used Voices/Performances in a single, easy-to-access

location and call them up by pressing the [FAVORITE] button.

You can add the current program to a favorite category by

simultaneously holding down the [SHIFT] button and

pressing this button. This is one more useful way you can

quickly select the Voices/Performances you need from the

huge number available on the instrument.

[DATA] dial

For editing the currently selected parameter. To increase the

value, turn the dial right (clockwise); to decrease the value,

turn the dial left (counter-clockwise). If a parameter with a

wide value range is selected, you can change the value in

broader strokes by quickly turning the dial.

[INC] button

For increasing the value of the currently selected parameter.

[DEC] button

For decreasing the value of the currently selected parameter.

NOTE

Simultaneously hold down the [SHIFT] button and press the [INC]

button to quickly increase the parameter value in 10-step jumps.

Simultaneously hold down the [SHIFT] button and press the [DEC]

button to quickly decrease the parameter value in 10-step jumps.

Cursor buttons

The cursor buttons move the “cursor” around the display,

highlighting and selecting the various parameters.

[SHIFT] button

Pressing this button along with another button enables you

to execute various commands. For details, refer to the “Shift

Function List” (page 62).

[EXIT] button

he menus and displays of the MOXF6/MOXF8 are organized

according to a hierarchical structure. Press this button to exit

from the current display and return to the previous level in the

hierarchy. Also use it to cancel a Job or a Store operation.

[ENTER] button

Use this button to call up the display of the selected menu.

Also use this button to execute a Job or a Store operation.

[MODE] buttons

These buttons select the MOXF6/MOXF8 operating modes

(e.g., Voice mode).

PERFORMANCE CREATOR (page 31)

This function is for quickly editing/creating a new Performance

based on the current Voice. This would come in handy when

a certain Voice has effect settings that you want to use in

your Performance program.

[LAYER] button

This button is for editing a layer Performance based on

the current Voice. When pressing this button, the

Category Search display appears and you can select the

Voices for use in a layer.

[SPLIT] button

This button is for editing a split Performance based on

the current Voice. When pressing this button, the

Category Search display appears and you can select the

Voices for use in a split.

[DRUM ASSIGN] button

This button is for editing a Performance with a Drum

Voice based on the current Voice. When pressing this

button, the Category Search display appears and you

can select the desired Drum Voice. Also, Arpeggio will

be set to on automatically.

BANK SELECT [DEC]/[INC] buttons

Use these buttons to select the desired Voice or

Performance Bank.

Group [A] – [H] buttons

Use these buttons to select the desired Group of Voices/

Performances. When the [CATEGORY SEARCH] button is

turned on, these buttons can be used to select a category.

When the [QUICK SETUP] button is turned on, these buttons

can be used to select a Quick Setup.

[COMMON] button

Turning this button on enters Common Edit, which lets you

MOXF6/MOXF8 Owner’s Manual

Control and Functions

edit the parameters commonly applied to all Elements, Parts

or Zones in the following modes: Voice Edit, Performance,

Song/Pattern Mixing Edit, Mixing Voice Edit and Master Edit.

[PATTERN SECTION/PERFORMANCE

CONTROL] button

This button is available in the Performance mode, Pattern

mode and Master mode. In the Performance mode, turning on

this button

will assign the following functions to the Number

[1] – [16] buttons.

In the Pattern mode, turning on this button will assign

Sections A – H to the Number [1] – [16] buttons.

In the Master mode, turning on this button lets you use the

Number buttons to switch the Internal Switch/External Switch

on/off for each Zone. For details about this function, see the

“Reference Manual” PDF document.

[TRACK] button

Turning this button on in the Song/Pattern mode enables the

Number [1] – [16] buttons for selecting corresponding Song/

Pattern Tracks. In the Voice mode/Performance mode, this

button lets you use the Number buttons to select the

Keyboard Transmit Channel.

[MUTE] button (page 41)

Turning this button on in Normal Voice Edit and Mixing Voice

Edit enables the Number [9] – [16] buttons for muting Voice

Elements (1 – 8). Turning this button on in the other modes

enables the Number [1] – [16] buttons for muting

Performance Parts (1 – 4), Song Tracks/Parts (1 – 16), and

Pattern Tracks/Parts (1 – 16).

[SOLO] button (page 41)

Turning this button on in Normal Voice Edit and Mixing Voice

Edit enables the Number [9] – [16] buttons for soloing a Voice

Element (1 – 8). Turning this button on in the other modes

enables the Number [1] – [16] buttons for soloing a

Performance Part (1 – 4), a Song Track/Part (1 – 16), and a

Pattern Track/Part (1 – 16).

NOTE The on/off status of buttons – affects the Number [1] – [16]

buttons in different ways, depending on the currently selected

mode. Refer to the table below.

Number [1] – [16] buttons

Use of these buttons differs depending on the on/off status of the [PATTERN SECTION/PERFORMANCE CONTROL], [TRACK],

[MUTE] and [SOLO] buttons.

Functions of the Number [1] – [16] buttons

Number button

Function

[1] – [4] Selecting Performance Parts 1 – 4.

[5] – [8] Setting the Arpeggio Switch to on/off for

Performance Parts 1 – 4.

[9] – [12] Setting the mute status for Performance Parts 1 – 4.

[13] – [16]

Setting the Arpeggio Hold for Performance Parts 1 – 4.

Mode

When the [PATTERN SECTION/

PERFORMANCE CONTROL]

button is turned on:

When the [TRACK] button

is turned on:

When the [MUTE]

button is turned on:

When the [SOLO]

button is turned

on:

When all the

buttons are

turned off:

Voice Play – Keyboard transmit channel

setting

– – Voice selection

Normal Voice

Edit

– Changes the Edit mode from

Common Edit to Element Edit

and Element selection ([1] –[8]).

Element Mute setting

([9] – [16])

Solo Element

selection ([9] – [16])

–

Drum Voice

Edit

– Changes the Edit mode from

Common Edit to Drum Key Edit

–––

Performance

Play

Performance Control ( ) Keyboard transmit channel

setting

Part Mute setting

([1] – [4])

Solo Part selection

([1] – [4])

Performance

selection

Performance

Edit

Performance Control ( ) Performance Part selection

([1] – [4])

Part Mute setting

([1] – [4])

Solo Part selection

([1] – [4])

–

Master Play –

Keyboard transmit channel setting

(when memorizing the Voice mode

or Performance mode to the

current Master) or Song/Pattern

Track selection (when memorizing

the Song mode or Pattern mode to

the current Master)

– – Master program

selection

Master Edit – Changes the Edit mode from

Common Edit to Zone Edit and

Zone selection ([1] – [4])

–––

Song/Pattern

Play

Section selection in the

Pattern mode

Song/Pattern Track selection Song/Pattern Track

Mute setting

Solo Track selection Song/Pattern

selection

Song/Pattern

Mixing

Section selection in the

Pattern mode

Song/Pattern Part selection Song/Pattern Part Mute

setting

Solo Part selection Voice selection of

the current Part

Mixing Voice

Edit

– Element selection ([1] – [8]) Element Mute setting

([9] – [16])

Solo Element

selection ([9] – [16])

–

MOXF6/MOXF8 Owner’s Manual

Control and Functions

Rear Panel

Standby/On switch (page 17)

Press to turn the power On ( ) or Standby ( ).

DC IN connector (page 17)

Connect the supplied power adaptor to this connector.

USB terminals

There are two different types of USB terminals, and the rear

panel of the instrument features both.

The USB [TO HOST] terminal is used to connect this

instrument to the computer via the USB cable and allows you

to transfer MIDI data and audio data between the devices.

Unlike MIDI, USB can handle multiple ports via a single

cable. For information about the Port handled by the MOXF6/

MOXF8, see page 54.

The USB [TO DEVICE] terminal is used to connect this

instrument to a USB flash memory device via the USB cable.

This lets you save data created on this instrument to an

external USB flash memory device and load data from a

USB flash memory device to the instrument. Save/Load

operations can be performed in the File mode (page 60).

NOTE Only USB flash memory device can be recognized by this

instrument. Any other USB storage devices (such as hard disk

drive, CD-ROM drive and USB hub) cannot be used.

NOTE Though the instrument supports the USB 1.1 standard, you can

connect and use a USB 2.0 storage device with the instrument.

However, note that the transfer speed is that of USB 1.1.

MIDI [IN] / [OUT] / [THRU] terminals

MIDI [IN] is for receiving control or performance data from

another MIDI device, such as an external sequencer, letting

you control this instrument from the connected separate

MIDI device.

MIDI [OUT] is for transmitting all control, performance and

playback data from this instrument to another MIDI device,

such as an external sequencer.

MIDI [THRU] is simply for redirecting any received MIDI data

(via MIDI [IN]) to connected devices, allowing convenient

chaining of additional MIDI instruments.

FOOT SWITCH [ASSIGNABLE]/[SUSTAIN]

jacks

For connection of an optional FC3/FC4/FC5 Footswitch to the

[SUSTAIN] jack and a FC4/FC5 Footswitch to the

[ASSIGNABLE] jack. When connected to the [SUSTAIN]

jack, the Footswitch controls sustain. When connected to

[ASSIGNABLE], it can control one of various different

assignable functions.

[FOOT CONTROLLER] jack

For connection of an optional foot controller (FC7, etc.). This

jack lets you continuously control one of various different

assignable functions—such as volume, tone, pitch, or other

aspects of the sound.

OUTPUT [L/MONO] and [R] jacks

Line level audio signals are output via these phone jacks. For

monophonic output, use only the [L/MONO] jack.

[PHONES] (Headphone) jack

This standard stereo phones jack is for connection to a set of

stereo headphones. This jack outputs audio signals identical

to those from the OUTPUT [L/MONO] and [R] jacks

A/D INPUT [L] and [R] jacks

External audio signals can be input via these phone jacks

(mono phone plug).

Various devices such as microphone, guitar, bass, CD player,

synthesizer can be connected to these jacks and their audio

input signal can be sounded as the Audio Part of the Voice,

Performance, Song, or Pattern. In addition, you can use the

special Vocoder feature (

page 39

) by connecting a

microphone

to one of these jacks and inputting your Voice to

the microphone.

Use mono phone plugs. For stereo signals (such as from

audio equipment), use both jacks. For mono signals (such

as from a microphone or guitar), use only one of these jacks

according to the “Mono/Stereo” parameter setting.

NOTE When using these jacks, make sure to confirm the “Mono/Stereo”

parameter setting which can be set in the following displays for

each mode:

• For the Voice mode: the VCE A/D display in the Utility mode

• For the Performance mode: the A/D IN display in Common Edit

• For the Song/Pattern mode: the A/D IN display in Mixing

Common Edit

MOXF6/MOXF8 Owner’s Manual

Power supply

Make connections for the supplied power adaptor (page 73)

in the following order. Before you connect the power adaptor,

make sure that the power of this instrument is set to the

Standby status.

1 Connect the plug of the power adaptor to the DC

IN terminal on the rear panel.

2 Connect the other end of the power adaptor to an

AC outlet.

NOTE Follow this procedure in reverse order when disconnecting the

power adaptor.

WARNING

Use the specified adaptor (page 73). The use of other adaptors may

result in irreparable damage to both the adaptor and the instrument.

CAUTION

• Make sure your MOXF6/MOXF8 is rated for the AC voltage supplied

in the area in which it is to be used (as listed on the rear panel).

Connecting the unit to the wrong AC supply can cause serious

damage to the internal circuitry and may even pose a shock

hazard!

• Even when the power of this instrument is in the Standby status,

electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure

you unplug the power adaptor from the wall AC outlet.

Connecting speakers or

headphones

Since this instrument has no built-in speakers, you will need

to monitor the sound of the instrument by using external

equipment. Connect a set of headphones, powered

speakers, or other playback equipment as illustrated below.

When making connections, be sure that your cables have

the appropriate ratings.

Powering up the system

Make sure the volume settings of this instrument and

external devices such as powered speakers are turned

down to the minimum before turning the power on. When

connecting this instrument to the powered speakers, turn on

the power switch of each device in the following order.

When turning the power on:

First, the MOXF6/MOXF8, then the connected powered

speakers.

When turning the power off:

First, the connected powered speakers, then the MOXF6/

MOXF8.

Please keep in mind that the Standby/On switch is located at

the right end (from the view of the keyboard) on the rear

panel of the MOXF6/MOXF8.

Setting Up

1 DC IN

2 Power adaptor plug

AC outlet

Powered speaker

(Left)

Powered speaker

(Right)

Headphones

OUTPUT L/MONO OUTPUT R

PHONES

MOXF6/MOXF8

Standby/

On switch

DC IN

MOXF6/MOXF8

MOXF6/MOXF8 Owner’s Manual

Setting Up

Auto Power Off function

To prevent unnecessary power consumption, this instrument

features an Auto Power Off function that automatically turns

the power off if the instrument is not operated for a specified

period of time.

 Auto Power Off Setting

The amount of time that elapses before the power is

automatically turned off can be set.

 Disabling Auto Power Off (simple method)

Turn the power on while holding down the lowest key on the

keyboard. A “Auto power off disabled.” indication appears

briefly and Auto Power Off is disabled. The setting is retained

even if the power is turned off.

NOTICE

• Even when the power is turned off, electricity is still flowing to the

instrument at the minimum level. To shut off the electricity

completely, make sure you unplug the power cord from the wall AC

outlet.

• Depending on the instrument status, the power may not turn off

automatically, even after the elapse of the specified period of time.

Always turn off the power manually when the instrument is not in

use.

• When the instrument is not operated for a specified period of time

while connected to an external device such as an amplifier, speaker

or computer, make sure to follow the instructions in the Owner’s

Manual to turn off the power to the instrument and the connected

devices, in order to protect the devices from damage. If you do not

want the power to turn off automatically when a device is

connected, disable Auto Power Off.

• The setting will revert to its default value if not backed up before the

power is turned off.

• When Auto Power Off is set to “off,” the value will be retained even if

the backup data saved on another device is loaded to the

instrument. When Auto Power Off is set to something other than

“off,” the value will be overwritten with loaded data.

NOTE The setting time is approximate.

NOTE To turn the power on after Auto Power Off has been executed,

press the Standby/On switch once to the Standby position, and

then press it again to the On position.

NOTE When the factory settings are restored, the setting time is

changed to the default value (30 min.).

Adjusting the volume and

the brightness of the

display

Adjust the volume levels of this instrument and the connected

amplifier/speaker system.

NOTE

When connecting to a set of powered speakers or PA equipment,

set the MASTER VOLUME to about 70%, then raise the volume of

the powered speakers or PA equipment to the appropriate level.

If the display is not easily visible, press the [INC]/[DEC] button

while holding the [UTILITY] button to adjust for optimum

visibility.

CAUTION

Do not listen with the headphones at high volume for long periods of

time. Doing so may cause hearing loss.

Instructions: [UTILITY]  [F1] GENERAL  [SF6] OTHER

 Set “AutoOff”  [STORE]

Setting Value

(min.):

off (Disables Auto Power Off), 5, 10, 15, 30,

60, 120

Default Setting

(min.):

Adjust the volume with the

MASTER VOLUME slider.

Adjust the display contrast.

Max.

Min.

MOXF6/MOXF8

MOXF6/MOXF8 Owner’s Manual

Setting Up

Starting up

Try playing some of the realistic and dynamic MOXF6/

MOXF8 sounds from the keyboard now. When you turn the

power on, the display below appears.

NOTE

In the default settings, the Master mode is selected. See

page 23

for details about the modes.

NOTE Keep in mind that the example displays shown in this manual are

for instruction purposes only, and may appear somewhat

different from those on your instrument.

In this condition you can play the keyboard and hear the

sounds of the selected program. In the default setting, the

Master mode provides a total of 128 programs each of which

includes the mode (Voice, Performance, Song, Pattern) and

its program number. The top of the Master Play display

indicates the Master program number and the status (Mode,

Bank, Program number and its name) registered to the

current Master program.

NOTE For details about Banks, see pages 25 and 34.

Selecting programs

In the default setting, the Master mode provides a total of 128

programs each of which includes the mode (Voice,

Performance, Song and Pattern) and its program number.

Try out the different Master programs to play various Voices

and Performances. You can change the Master program

number by using the [INC] button, [DEC] button, or [DATA]

dial.

Playing the Demo Songs

The MOXF6/MOXF8 features a variety of Demo Songs,

showcasing its dynamic sound and sophisticated functions.

Here’s how to play them back.

1 Press the [SONG] button to enter the Song Play

mode.

The PLAY display appears.

2 Press the SEQ TRANSPORT [F] (Play) button to

start the Demo Song.

The Song currently shown on the display starts.

NOTE

To adjust the volume level of the Demo Songs, use the

[MASTER VOLUME] slider.

3 Press the SEQ TRANSPORT [J] (Stop) button to

stop the Demo Song.

Select another Demo Song by using the [INC] button

or [DATA] dial.

5 Play the selected Demo Song by performing Steps

2 and 3.

Program name Master program number

Mode Bank Program number

Decreases number Increases number

Decreases

number

Increases

number

Stop button Play button

MOXF6/MOXF8 Owner’s Manual

Setting Up

Resetting User Memory to

the initial factory settings

The original factory settings of this synthesizer’s User

Memory can be restored as follows.

NOTICE

When the factory settings are restored, all the Voice, Performance,

Song, Pattern, and system settings in the Utility mode you created will

be erased. Make sure you are not overwriting any important data. Be

sure to save all important data to your USB flash memory device

before executing this procedure (page 60).

1 Press the [UTILITY] button then the [JOB] button to

call up the Factory Set display.

2 Press the [ENTER] button.

The display prompts you for confirmation. To cancel this

operation, press the [EXIT] button here.

NOTICE

When entering a checkmark to the box of Power On Auto Factory Set

and executing Factory Set, the Factory Set operation will

automatically be executed each time you turn the power on. Keep in

mind that this also means that your original data in Flash ROM will be

erased each time you turn on the power. Therefore, the checkmark of

this box should normally be removed. If you remove the checkmark of

this box and execute Factory Set, the Factory Set operation will not

be executed when turning the power on the next time.

3 Press the [ENTER] button to execute Factory Set.

After Factory Set has been completed, a “Completed”

message appears and operation returns to the original

display.

NOTICE

For Factory Set operations that take longer to process, you will see

the message “Now executing Factory Set…” during processing.

While such a message is shown on the display, never attempt to turn

off the power. Turning the power off in this state results in loss of all

user data and may cause the system to freeze (due to corruption of

data in the Flash ROM). This means that this synthesizer may not be

able to start up properly, even when turning the power on next time.

MOXF6/MOXF8 Owner’s Manual

Moving the cursor

Use these four buttons to navigate the display, moving the

cursor around the various selectable items and parameters

in the screen. When selected, the relevant item is highlighted

(the cursor appears as a dark block with inverse characters).

You can change the value of the item (parameter) at which

the cursor is located by using the [DATA] dial, [INC] and

[DEC] buttons.

Changing (editing) parameter

values

Rotating the [DATA] dial to the right (clockwise) increases

the value, while rotating it to the left (counter-clockwise)

decreases it.

Pressing the [INC] button increases a parameter value by

one step, and pressing [DEC] decreases it. Pressing and

holding either button continuously increases or decreases

the value.

For parameters with large value ranges, you can increase

the value by 10 by simultaneously holding down the [SHIFT]

button and pressing the [INC] button. To decrease by 10,

simultaneously hold down the [SHIFT] button and press the

[DEC] button.

Functions and Sub-Functions

Each mode described above contains various displays, with

various functions and parameters. To navigate your way

through these displays and select a desired function, use the

[F1] – [F6] buttons and the [SF1] – [SF6] buttons. When you

select a mode, the available displays or menus appear directly

above the buttons at the bottom of the display (as shown

below).

Depending on the currently selected mode, up to six functions

are available and can be called up with the [F1] – [F6] buttons.

Keep in mind that the available functions differ depending on

the selected mode. Depending on the currently selected

function, up to six sub-functions are available and can be

called up with the [SF1] – [SF6] buttons. Keep in mind that

the available sub-functions differ depending on the selected

function.

The example display below is called up by pressing the [F5]

LFO button then pressing the [SF1] Wave button. In this

example display, no sub-function is assigned to the [SF6]

button.

Inputting a number directly

For parameters having large value ranges, you can also

enter the value directly, using the buttons below the LCD as

a numeric keypad. When the cursor is located on such a

parameter, the [NUM] icon appears at the lower right corner

of the LCD. When the [SF6] NUM button is pressed in this

status, each digit (1 – 9, 0) is assigned to the [SF1] – [SF5]

and [F1] – [F5] buttons as shown below, allowing you to

input a number directly by using these buttons. Depending

on the selected parameter, a negative value can be input.

When such a parameter is selected and you wish to input a

negative value, press the [F6] button (to which “-” is assigned)

then use the [SF1] – [SF5] and [F1] – [F5] buttons. After

completing the number input, press the [ENTER] button to

actually enter the number and exit from this status.

Basic Operation

Decreases number Increases number

Decreases

number

Increases

number

These functions can be selected

via the corresponding button

([F1] – [F6]).

These functions can be selected

via the corresponding button

([SF1] – [SF6]).

You can use these buttons

as a numeric keypad.

MOXF6/MOXF8 Owner’s Manual

Basic Operation

Naming (inputting characters)

You can freely name the data you’ve created, such as Voices,

Performances, Songs, Patterns and files saved to a

USB

flash memory device. When the cursor is located on such a

naming

parameter, the “CHAR” icon appears at the lower

right corner

of the display. When pressing the [SF6] button in

this status, the Input Character window appears as shown

below.

In the Edit area, you can move the cursor to determine the

location at which the character is to be input by pressing the

[<] or [>] button while holding the [SF6] button.

In the Character List, you can move the cursor to determine

the character to be input by rotating the [DATA] dial or

pressing the [INC] or [DEC] button while holding the [SHIFT]

button. After completing the character input, press the

[ENTER] button to actually enter the currently edited name

and exit from this status.

Selecting a note type

When the cursor is located on a parameter for which note

types are to be set, the note icon appears at the lower right

corner indicating that you can call up the Note Type selection

window by pressing the [SF6] button. You can specify the

note type by pressing the [F1] – [F5] buttons and the [SF1] –

[SF5] buttons.

Note (Key) and Velocity settings

Several parameters let you set a key range or velocity range

for a function—for example, in setting up a keyboard

split—by specifying certain note values. You can use the

[INC] and [DEC] buttons or [DATA] dial to set these

parameters, or you can directly enter the values from the

keyboard by pressing the appropriate keys. When the cursor

is located on such a parameter, the “KBD” icon appears at

the lower right corner of the display. You can set the note or

velocity directly from the keyboard by holding down the

[SF6] button and pressing the desired key.

Character ListEditing area

Note Type selection

window

MOXF6/MOXF8 Owner’s Manual

Modes

There are several operation modes in this instrument,

and they can be selected by using the ten Mode

buttons, – . In addition, there are three “global”

modes (Edit, Job and Store) common to all of these

modes, and they can be selected by using buttons

– .

Quick Guide

No. Button Mode Description

[VOICE] Voice mode This synthesizer has a wealth of high quality, dynamic sounds—also referred to as “Voices.” You can

play these Voices—one Voice at a time—from the keyboard in the Voice mode. This mode also lets

you create your own original Voices.

[PERFORM] Performance mode

This mode lets you play and create Performances. A Performance lets you put several different Voices

together in layers or play different two Voices in a keyboard split.

[MASTER] Master mode This mode lets you register settings that you often use in the Voice, Performance, Song or Pattern

mode, and instantly recall the relevant mode and custom settings together in a single button

press

—without having to first select a mode. In addition, this mode lets you divide the keyboard into

four separate sections—just as if you were playing four different MIDI keyboards.

[SONG] Song mode This mode lets you record, edit and play your own original Songs.

[PATTERN] Pattern mode This mode lets you play, record, edit and play your own original rhythm patterns, which can be used

to make up a Song.

[MIXING] Song Mixing mode/

Pattern Mixing mode

This mode lets you set up detailed parameters of the multi-timbral tone generator for use with Song/

Pattern playback.

[FILE] File mode This mode lets you save data you’ve created on this instrument to a USB flash memory device, and

allows you to load data from the USB flash memory device to the MOXF6/MOXF8.

[UTILITY] Utility mode This mode lets you set parameters that apply to the entire system of this instrument.

[QUICK SETUP] Quick Setup mode This mode lets you register up to six settings for MIDI connection and Audio connection between

this instrument and the computer as “Quick Setups,” and instantly recall the custom settings with a

single button press.

[DAW REMOTE] Remote mode

This mode lets you control DAW software on your computer from the panel controls of the instrument.

[EDIT] Edit This mode lets you edit various parameters in each of the Voice, Performance, Song, Pattern and

Master modes.

[JOB] Job This mode lets you execute various commands such as Initialize, Copy, and MIDI data

conversion—useful for creating your original programs.

[STORE] Store This mode lets you store the edited program to internal memory.

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Basic Instructions

Selecting a Preset Voice ..................................................................................................... page 25

Editing a Voice .................................................................................................................... page 28

Creating a new Performance in the Voice mode by using your favorite Voices

(Performance Creator) ........................................................................................................ page 31

Selecting a Performance..................................................................................................... page34

Editing a Performance ........................................................................................................ page 34

Playing the keyboard along with the sound input from the A/D INPUT [L]/[R] jacks ........... page 38

Creating an original Song ................................................................................................... page40

Creating an original Pattern ................................................................................................ page47

Using as a Master Keyboard (Master Mode) ...................................................................... page 57

Recording your performance on the MOXF6/MOXF8 to DAW ............................................ page 54

Using the MOXF6/MOXF8 as a tone generator for DAW playback ..................................... page 55

Remote-controlling the DAW (Remote mode)..................................................................... page 55

Using the MOXF6/MOXF8 Editor VST as a software synthesizer....................................... page 57

Making global system settings (Utility mode/Quick Setup) ................................................. page 58

Saving / loading data in the File mode................................................................................ page 60

Voices—the basic building blocks of the MOXF6/MOXF8

Combining several Voices to create a Performance

Connecting a microphone or audio equipment

Song/Pattern—created by recording your keyboard performance and assembling

Pattern sections

Master mode—create a master keyboard setup or instantly call up your desired programs

Music creation by using a computer

Global settings and data backup

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Playing the keyboard in

the Voice mode

In the Voice Play display (the top display of the Voice mode),

you can select and play a single Voice. The Voices of this

instrument are divided into the following two types:

Normal Voice

Normal Voices are mainly pitched musical instrument type

sounds (piano, organ, guitar, etc.) that can be played over

the range of the keyboard.

Drum Voice

Drum Voices are mainly percussion/drum sounds that are

assigned to individual notes. These Voices are used to

perform rhythm parts.

This instrument features Banks for memorizing Voices. There

are basically three different types of Banks: Preset, User, and

GM. The contained Voices and features depend on the Bank

as described below.

Preset Banks

The Preset Banks contain a full set of specially programmed

Voices. Voices you've edited yourself cannot be saved in the

Preset Banks.

User Banks

The User Banks contain the Voices you have edited and

stored. By default, these are comprised of Preset Voices.

NOTICE

If a Voice in a User Bank (User Voice) is overwritten or replaced, that

User Voice will be lost. When you store an edited Voice, be careful not

to overwrite any important User Voices.

NOTE You can also conveniently use the User Bank to save desired

Voices in consecutive order for live performance situations.

GM Bank

The GM Bank contains the Voices allocated according to the

GM standard.

In the Voice mode, a total of 16 Banks (Preset Bank 1 – 9,

User Bank 1 – 3, GM Bank, Preset Drum Bank, User Drum,

GM Drum Bank) are available. Each of these Banks includes

the Voices according to the Voice type. In the Voice Play

display, you can select the desired Voice from various Voice

Banks and play it.

NOTE For details about Voices, refer to “Basic Structure.” For a list of

the Preset Voices, refer to the separate Data List PDF file.

Selecting a Preset Voice

1 Press the [VOICE] button.

This calls up the Voice Play display. (The [VOICE] button

lamp lights.)

2 Select a Voice Bank with the BANK SELECT

[DEC]/[INC] buttons.

In this condition, playing the keyboard sounds the Voice

indicated in the display. The parameters shown in the Voice

Play display are briefly explained below.

Voice Play display

Normal Voice Banks

There are 13 different banks for the Normal Voices: PRE1 – 9

(Preset Banks), USR1 – 3 (User Banks), GM (GM Bank).

Drum Voice Banks

There are 3 different banks for the Drum Voices: PDR (Preset

Drum Bank), UDR (User Drum Bank), GMDR (GM Drum

Bank).

3 Select a Voice with the [DATA] dial or [INC]/[DEC]

buttons.

NOTE You can use the [DATA] dial or [INC]/[DEC] buttons to select

the Voice number. This operation lets you call up Voices in

subsequent or previous Banks.

NOTE To quickly move forward through the program (Voice)

numbers in 10-step jumps, simultaneously hold down the

[SHIFT] button and press the [INC] button in the Play display.

To decrease by 10, do the opposite; simultaneously hold

down the [SHIFT] button and press the [DEC] button.

4 Play the keyboard.

GM Voice

GM (General MIDI) is a worldwide standard for Voice

organization and MIDI functions of synthesizers and tone

generators. It was designed primarily to ensure that any Song

data created with a specific GM device would sound virtually

the same on any other GM device—no matter the manufacturer

or the model. The GM Voice bank on this synthesizer is designed

to appropriately play back GM Song data. However, keep in

mind

that the sound may not be exactly the same as played by

the original tone generator.

Main Category Bank Program number Sub Category

Voice name

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Using the Category Search

function

The Voices are conveniently divided into specific Categories,

irrespective of their bank locations. The categories are

divided based on the general instrument type or sound

characteristics. The Category Search function gives you quick

access to the sounds you want.

Press the [CATEGORY SEARCH] button in the Voice

Play display.

The Category Search display appears.

Move the cursor position to “Main” (Main Category)

with the Cursor [ ] button, and use the [DATA]

dial to select the Main Category.

3 Move the cursor position to “Sub” (Sub Category)

with the Cursor [ ] button, and use the [DATA]

dial to select the Sub Category.

4 Press the [ENTER] button, or Cursor [>] button to

actually call up the selected Category.

The Voice List of the selected category is shown.

5 Select the Voice with the Cursor [ ]/[ ] buttons

or [DATA] dial.

If you want to change the Category, press the Cursor [<]

button or [EXIT] button and go back to step 2.

6 Press the [ENTER] button to actually call up the

Voice.

This closes the Category Search display.

Grouping your most-used Voices

together—Favorite Category

Category Search also has a convenient Favorite Category

that lets you collect your most often used and favorite Voices

for easy selection. This is one more useful way you can

quickly select the Voices you need from the huge number

available on the instrument.

1 Perform steps 1 through 4 of the “Using the

Category Search function” instructions to call up

the Voice List of the selected Category.

2 Select the desired Voice with the Cursor [ ]/[ ]

buttons or [DATA] dial.

3 Press the [F5] SET/CLR button to turn on the

Favorite mark.

This operation will turn on the Favorite mark, making it solid

( ), and the selected Voice will be registered to the Favorite

Category. Pressing the [F5] SET/CLR button again will turn

off or “ghost” the Favorite mark ( ).

To register other Voices, repeat steps 2 through 3.

To remove all the Voices from the Favorite Category, press

the [F6] CLR ALL button.

4 When you complete registering Voices to the

Favorite Category, press the [ENTER] button to

return to the Voice Play display.

This operation will exit from the Category Search display and

store the Favorite Category settings to internal Flash ROM.

To register/remove the current Voice to/from the Favorite

Category, simply hold the [SHIFT] button then press the

[FAVORITE] button.

Main Category

Sub Category

Voice list of the currently

selected category.

Main Category icon

Sub Category

Registering your favorite Voices to the

Favorite Category

Favorite marks

MOXF6/MOXF8 Owner’s Manual

Quick Guide

1 Press the [FAVORITE] button in the Voice Play

display.

The list of Voices registered to the Favorite Category will be

shown.

2 Select the Voice with the Cursor [ ]/[ ] buttons

or [DATA] dial.

3 Press the [ENTER] button to actually call up the

Voice.

Using the Arpeggio function

The Arpeggio function automatically triggers preset arpeggio

phrases, riffs, and rhythmic patterns according to the notes

you play.

It not only provides inspiration and full rhythmic passages

over which you can perform, it gives you quality MIDI data

you can use in creating Songs, or fully formed backing parts

to be used in your live performances. You can assign the

desired six Arpeggio Types to each Voice. You can also assign

the desired six Arpeggio Types to each Part of each

Performance/Song/Pattern and play back the Arpeggios of

up to four Parts simultaneously.

You can also set the Arpeggio playback method, Note range,

Velocity range and Play Effects to create your own original

grooves. What’s more, Arpeggio playback can be transmitted

through MIDI Out, letting you record the Arpeggio data to a

sequencer.

NOTE For details about Arpeggio, see the “Reference Manual” PDF

document.

To turn Arpeggio playback on or off, press the ARP [ON/OFF]

button on the panel.

Arpeggio types are assigned to each of the [SF1] – [SF6]

buttons, the corresponding tabs of which are indicated by

8th note icons ( ) at the right of “ARP1” – “ARP6.” This means

hat you can change the Arpeggio type by pressing the

[SF1] – [SF6] buttons as desired.

NOTE For information on setting the Arpeggio Type, refer to “Changing

the Arpeggio Type assignment” on page 31.

Keyboard Octave/Transpose setting

To shift the pitch range in playing the keyboard, use the

OCTAVE [-]/[+] buttons and TRANSPOSE [-]/[+] buttons.

Octave

The OCTAVE [-]/[+] button lets you shift the pitch of the

keyboard in octaves, up to a maximum of three. For example,

you may want to shift the pitch down lower to get extra bass

notes, or shift up to get higher notes for leads and solos. The

OCTAVE [-]/[+] controls let you do this quickly and

easily. The

range is from -3 to +3, with 0 being standard pitch.

Pressing

the [-] and the [+] buttons together at the same time

will

return the setting to the initial value (0).

The current octave range can be confirmed via the status of

the lamp of the OCTAVE [-]/[+] buttons. When set to one

octave down or up, the corresponding lamp lights. When set

to two octaves down or up, the corresponding lamp flashes

slowly. When set to three octaves down or up, the

corresponding lamp flashes quickly.

Transpose

The TRANSPOSE [-]/[+] button lets you shift the pitch of the

keyboard in semitones (up to 11 semitones). This function

allows you to play in the same position and with the same

fingering, even if the Song data or another instrument player

is playing in a different key. The Transpose Up/Down controls

let you do this quickly and easily. Pressing the [-] and the [+]

buttons together at the same time will return the setting to the

initial value (0). When set to one semitone down or up, the

corresponding lamp lights.

Selecting a Voice from the Favorite Category

Turning the Arpeggio On/Off

Changing the Arpeggio type

ARP1 – ARP6 buttons

MOXF6/MOXF8 Owner’s Manual

Quick Guide

NOTE This parameter is same as “Octave” and “Transpose” in the

GENERAL display of the Utility mode. Making a setting

here

automatically changes the setting of that parameter as well.

Changing the tonal qualities of the

Voice

Knobs 1 – 8 let you adjust a variety of parameters for the

current Voice, such as effect depth, attack/release

characteristics, timbre, and others. Three functions can be

assigned to each Knob, alternatively selected via the Knob

Function buttons.

1 Press the Knob Function 1 button (at the left of

Knobs 1 – 4) and Knob Function 2 button (at the left

of Knobs 5 – 8) repeatedly if necessary, so that the

lamp corresponding to the desired functions

lights.

The KNOB FUNCTION pop-up window will appear. In the pop-

display, the function currently assigned to the knob and

the current value of the function are shown. To close the pop-

window, press the [EXIT] button.

NOTE

When the “Knob FuncDispSw” is set to “off” in the Utility

GENERAL display, the KNOB FUNCTION pop-up window

will not be shown.

2 Turn a desired knob while playing the keyboard.

The KNOB FUNCTION pop-up window will appear, and the

function assigned to the knob you’re currently operating will

affect the sound of the current Voice. The KNOB FUNCTION

pop-up window shows the function assigned to the knob

you’re currently operating, the function value, and the

“Original” value. The “Original” value indicates the unedited

value (previously stored value) of the function assigned to

the knob.

Editing a Voice

“Editing” refers to the process of creating a Voice by changing

the parameters that make up the Voice. This can be done in

Voice Edit, a sub mode within the Voice mode. The actual

parameters that are available differ depending on the Voice

type.

A Normal Voice (pitched musical instrument-type sounds)

can consist of up to eight Elements. There are two types of

Voice Edit displays: Common Edit, for editing the settings

common to all eight Elements; and Element Edit, for editing

individual Elements.

NOTE An Element is the basic and the smallest unit for a Voice, and is

created by applying various parameters (Effect, EG, etc.) to the

waveform of the instrument sound. Each Voice of this instrument

consists of several Elements.

There are two types of Drum Voice Edit displays: Common

Edit, for editing the settings that apply to all Drum keys in the

Voice; and Key Edit, for editing individual keys.

Knob Function 1 button

Knob Function 2 button

Functions assigned to Knobs

1 – 4 or 5 – 8

Current values of

the functions

Unedited value (previously stored)

Knob 1 Knob 2 Knob 3 Knob 4

Knob 5 Knob 6 Knob 7 Knob 8

HINT

The Edit Indicator

When changing the value of the parameter, the Edit Indicator

will appear on the top right corner of the LCD. This gives a

quick confirmation that the current program (such as Voice and

Performance) has been modified but not yet stored. To store

the current edited status, execute the Store operation (below).

Normal Voice Edit

Drum Voice Edit

Function of currently operated Knob Current value

Unedited value (previously stored)

MOXF6/MOXF8 Owner’s Manual

Quick Guide

1 Press the [EDIT] button in the Voice mode.

2 Edit the current Voice.

When a Normal Voice is selected:

To edit Common parameters, press the [COMMON] button.

To edit Element parameters, press the desired Element

number button from [1] – [8].

When a Drum Voice is selected:

To edit Common parameters, press the [COMMON] button.

To edit Key parameters, press the [1] button then press the

desired note on the keyboard.

NOTE

For details about the Voice parameters, refer to the Voice

mode chapter in the Reference Manual.

3 Assign the name to the edited Voice.

On the display called via [COMMON]  [F1] GENERAL 

[SF1] NAME, enter the desired name.

4 Store your edits as a User Voice.

Press the [STORE] button to call up the Store display. Set the

destination memory then press the [ENTER] button to execute

the Store operation.

NOTE

To cancel the Store operation, press the [EXIT] button before

pressing the [ENTER] button.

NOTICE

Never attempt to turn off the power while data is being written to Flash

ROM (while an “Executing...” or “Please keep power on” message is

shown). Turning the power off in this state results in loss of all user

data and may cause the system to freeze (due to corruption of data in

the Flash ROM).

Enhancing the sound with Effects

This instrument features a wide variety of Effects, letting you

add reverb and chorus processing to the selected Voice for

your keyboard performance. Simply changing the Effect

type applied to the preset Voice lets you instantly come up

with different sounds. The instructions below explain how to

set the Effect type and the related parameters applied to the

Preset Voice then store the settings as a User Voice.

1 In the Voice Play display, select a Voice then press

the [F6] EFFECT button.

The EFFECT display of Voice Common Edit appears.

2 Select the Effect Category and Type of Insertion

Effect A.

Move the cursor to the corresponding position as shown

below then use the [INC]/[DEC] buttons or [DATA] dial.

Basic Procedure for Voice Edit

Common Edit display

Element Edit display

Key Edit display

Indicates the Common Edit display.

Indicates the display for editing Element 1.

Indicates the Key Edit display.

Select a Key here.

Store display

Destination

Bank

Destination Voice

name

Destination Voice

number

HINT

Compare function

The Compare function lets you switch between the just-edited

Voice and its original, unedited condition, allowing you to hear

how your edits affect the sound.

In the Voice Edit mode (with the [EDIT] lamp lit):

Press the [EDIT] button so that its lamp flashes. In this status,

the Voice settings prior to editing will temporarily be reinstated

for comparison purposes. Press the [EDIT] button again to

return to the original status.

In the Voice Store mode:

Press the [EDIT] button so that its lamp flashes. In this status,

you can hear the sound of the Voice at the storing destination.

Press the [EDIT] button again to return to the original status.

Insertion Effect A Category Insertion Effect A Type

The current parameter and its value

MOXF6/MOXF8 Owner’s Manual

Quick Guide

3 Select the Effect Category and Type of Insertion

Effect B with the same instruction as step 2.

4 Select the Effect connection of Insertion A and B.

Move the cursor to the position shown below then use the

[INC]/[DEC] buttons or [DATA] dial.

5 Set the output destination of each Element/Key.

Move the cursor to “EL:OUT” (for the Normal Voice) or

“KEY:OUT” (For the Drum Voice) then use the [INC]/[DEC]

buttons or [DATA] dial.

6 If necessary, edit the Effect parameters on the

display called up via the [SF2] INS A/[SF3] INS B

buttons.

Try narrowing in on your desired sound by finely editing the

parameters provided for each Effect Type.

7 After setting the parameters, press the [STORE]

button to store your settings as a User Voice.

Insertion Effect connection

Element Out 1 – 8

HINT

You can use the following operation to simultaneously adjust

the volume of Elements 1 – 8 together:

1 Press the Knob Function 1 button (at the left of Knobs 1

– 4) and Knob Function 2 button (at the left of Knobs 5 –

8) simultaneously.

The six lamps light and the KNOB FUNCTION pop-up

window will appear.

2 Turn one of the knobs to adjust the Element volume.

3 After completing editing, press the [EXIT] button to

return to the Voice Play display.

Knob Function 1 button

Knob 1 Knob 2 Knob 3 Knob 4

Knob 5 Knob 6 Knob 7 Knob 8

Knob Function 2 button

HINT

Using Controllers

Multiple controllers are assigned to each preset Voice,

allowing you to apply various changes and effects to the Voice

in real time. For convenience, abbreviations of the important

or characteristic controllers for that Voice are shown following

the Voice name in the display. However, some Voices may

have indications for controllers that are not actually available

on the instrument itself. These can be used, though, by

transmitting the corresponding MIDI control number from an

internal sequencer, an external sequencer, or an external MIDI

controller.

Controller

Indication

Controller Name

MIDI Control

Number

(default setting)

AS1 ASSIGN 1 knob 16

AS2 ASSIGN 2 knob 17

AF1 ASSIGNABLE FUNCTION

[1] button

AF2 ASSIGNABLE FUNCTION

[2] button

FC1 Foot Controller 11

FC2 not included on panel 4

MW Modulation Wheel 1

RB not included on panel 22

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Changing the Arpeggio Type

assignment

Try changing the Arpeggio Types assigned to the [SF1] – [SF6]

buttons of the Preset Voice.

1 Press the ARP [EDIT] button.

The Arpeggio Edit display appears.

2 Press the desired Arpeggio button, [SF1] ARP1 –

[SF6] ARP6.

3 Press the [F2] TYPE button to call up the TYPE

display.

4 Select the desired Arpeggio Type you want to

assign.

Edit the “Bank,” “Category,” “SubCategory,” and “Type” by

using the [DATA] dial.

5 Edit the other parameters if necessary.

6 Turn on the ARP [ON/OFF] button then play the

keyboard.

Creating a new Performance

by using your favorite Voice

(Performance Creator)

A program in which multiple Voices (parts) are combined in

a layer, or in other configurations is referred to as a

“Performance.” Each Performance can contain up to four

different parts (Voices).

This instrument features a convenient Performance Creator

function which lets you create a new Performance by using

favorite Voices you’ve found in the Voice mode. This function

lets you copy parameter settings associated with the Voice

(such as Effects) to the Performance—allowing you to quickly

and easily come up with precisely the sound you want.

Performance Creator provides three convenient features:

Layer, Split, and Drum Assign.

Layer—Playing different Voices

together

This section explains how to create a Performance in which

different Voices are layered together across the keyboard.

By creating such a Performance, you can play a rich, thick

sound of a layered piano and strings, for example.

1 Select a Voice in the Voice mode.

2 Press the [LAYER] button on the panel.

The Category Search display appears.

3 Select the Category including the Voice you want

to layer then press the Cursor [>] button.

The Voice list is shown.

HINT

Copying the Arpeggio Type to another button

To copy the ARP 1 button’s Arpeggio Type to one of the ARP

2 – 6 buttons, hold the [STORE] button and press the desired

button, [SF2] – [SF6], in the Arpeggio Edit display.

MOXF6/MOXF8 Owner’s Manual

Quick Guide

4 Select the desired Voice from the list, then press

the [ENTER] button.

The Performance Play display will appear.

The Voice selected in the Voice mode will be assigned to

Part 1, and the Voice selected after pressing the [LAYER]

button will be assigned to Part 2. These two Voices are

sounded simultaneously in a layer as a “Performance.”

You can confirm what Voices are layered on the display called

up via the [F2] VOICE button.

5 Press the [STORE] button to store the settings as

a Performance.

NOTE When you press the [EDIT] button in the Store display, you

can check the sound of the Performance at the storing

destination.

Split—Playing two different Voices

with your left and right hands

This section shows you how to create a Performance in which

the keyboard is divided (or split) into two sections—the left-

hand section and the right-hand. The lowest note of the right-

hand section is referred to as the “Split Point.” By creating

such a Performance, you can play a bass part with your left

hand, and a piano part with your right hand, for example.

1 Select a Voice in the Voice mode.

2 Press the [SPLIT] button on the panel.

The Category Search display appears.

Move the cursor to “SPLITPOINT” then set the Split

Point.

You can determine the Split Point by holding the [SHIFT]

button then pressing the desired note on the keyboard.

NOTE

The note set to the Split Point is included in the upper section

of the keyboard.

4 Move the cursor to “LO/UP” then select whether

the desired Voice is assigned to the lower section

or the upper section of the keyboard.

NOTE When the original Voice is a Drum Voice, Split is not applied

to the part assigned the Drum Voice. In this case, only the

desired Voice is assigned to the keyboard range according

to the “SPLITPOINT” and “LO/UP” settings.

5 Move the cursor to “Main”/“Sub” then select the

Category that includes your desired Voice.

6 Press the Cursor [>] button.

The Voice list is shown.

MOXF6/MOXF8 Owner’s Manual

Quick Guide

7 Select the desired Voice from the list, then press

the [ENTER] button.

The Performance Play display will appear.

The Voice selected in the Voice mode will be assigned to

Part 1, and the Voice selected after pressing the [SPLIT]

button will be assigned to Part 2. These two Voices are

sounded in different areas of the divided keyboard as a

“Performance.”

You can confirm what Voices are assigned on the display

called up via the [F2] VOICE button.

8 Press the [STORE] button to store the settings as

a Performance.

Drum Assign—Layering a drum

Part with the current Voice

This section explains how to create a Performance in which

you can trigger a drum pattern (via the Arpeggio function) in

addition to the current Voice.

1 Select a Voice in the Voice mode.

2 Press the [DRUM ASSIGN] button on the panel.

The Category Search display appears. Drum/Percussion is

automatically assigned as the Category. The Drum Voice is

assigned to Part 4 then the Arpeggio is automatically turned

on. Play the keyboard to trigger the Arpeggio.

3 Press the Cursor [>] button.

The Voice list is shown.

4 Select the desired Drum Voice from the list, then

press the [ENTER] button.

The Performance Play display will appear.

NOTE

To stop Arpeggio playback, press the ARP [ON/OFF] button so

that its lamp is turned off. To start or enable Arpeggio playback

again, press the ARP [ON/OFF] button so that its lamp lights.

Changing the drum pattern

(Arpeggio Type)

Executing the Drum Assign function will assign a Drum Voice

to Part 4 and set the Arpeggio of Part 4 to on. If you want to

change the drum pattern, select a different Arpeggio Type in

the Arpeggio Edit of the Performance mode.

5 Press the ARP [EDIT] button in the Performance

Play display.

The Arpeggio Edit display appears.

6 Press the [F2] TYPE button then the Number [4]

button.

The TYPE display for Part 4 appears.

7 Select the Arpeggio Type with “Bank,” “Category,”

“Sub Category” and “Type.”

8 Press the [PERFORM] button to return to the

Performance Play display.

9 Press the [STORE] button to store the edited

Performance.

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Playing the keyboard in

the Performance Mode

A program in which multiple Voices (parts) are combined in

a layer, or in other configurations is referred to as a

“Performance.” This instrument contains 128 Performances

in each of the User Banks 1 – 2 and you can play them by

pressing the [PERFORM] button.

Selecting a Performance

Selecting a Performance is done in basically the same way

as selecting a Voice (see page 25). As in the Voice Play

mode, you can use the Category Search (page 26) and

Favorite Category (page 26) functions in the Performance

Play mode.

Switching a Part on/off

The Performance Play mode lets you turn the four Parts of

the current Performance on or off as desired.

You can turn individual Parts on/off by using the Mute function.

1 Press the [PERFORMANCE CONTROL] button.

The button lamp lights, indicating that each Part can be

turned on/off.

2 Press any of the Number [9] – [12] buttons.

The lamp of the pressed button will be turned off and the

corresponding Part will be muted. Press the same button

again to turn the lamp on and disengage the mute function

for that Part. You can turn multiple Parts on/off by pressing

their buttons.

NOTE

Parts can be muted also by pressing the [MUTE] button then

the Number [1] – [4] buttons.

The Solo function is the opposite of Mute, and lets you instantly

solo a specific Part and mute all others.

1 Press the [SOLO] button.

The SOLO lamp lights, indicating that Solo is enabled.

2 Press any of the Number [1] – [4] buttons.

The lamp of the pressed button will flash and only the

corresponding Part will be sounded. Press any other Number

button to change the solo Part.

NOTE

You can exit from this status by pressing the [TRACK] button

or [PERFORMANCE CONTROL] button.

Using the Arpeggio function

The Arpeggio function lets you trigger rhythm patterns, riffs

and phrases using the current Voice by simply playing notes

on the keyboard. In the Performance mode, each of four

Arpeggio types is assigned to each of four Parts. This means

four Arpeggio types can be played back simultaneously. Try

selecting different Performances and check out the various

Arpeggio types.

NOTE For details about Arpeggio, see the “Reference Manual” PDF

document.

Since the preset Performances already have their own

Arpeggio types pre-assigned, you can play the Arpeggio by

selecting the desired Performance, turning on the ARP [ON/

OFF] button, then pressing any note. Instructions on using

Arpeggio are basically the same as in the Voice mode.

Turning specific Parts on/off (Mute function)

Soloing a specific Part

MOXF6/MOXF8 Owner’s Manual

Quick Guide

You can turn Arpeggio playback on or off for each Part of the

Performance as described below.

1 Press the [PERFORMANCE CONTROL] button.

The [PERFORMANCE CONTROL] lamp lights, indicating

that Arpeggio playback for each Part can be turned on/off.

2 Pressing each of the Number [5] – [8] buttons

toggles Arpeggio playback on and off for each

Part.

If any of the [5] – [8] lamps is turned off, the Arpeggio

playback of the corresponding Part is muted.

You can turn the Arpeggio Hold parameter on /off or on/sync-

off for each Part of the Performance as described below.

When the Arpeggio Hold parameter is set to “on,” Arpeggio

playback continues even if the note is released.

NOTE The Arpeggio Hold parameter is in the [F3] MAIN display of the

Arpeggio Edit display. For details on this parameter, see the

Reference Manual.

1 Press the [PERFORMANCE CONTROL] button.

The [PERFORMANCE CONTROL] lamp lights, indicating

that Arpeggio Hold for each Part can be turned on/off or on/

sync-off.

2 Pressing each of the Number [13] – [16] buttons

toggles the Arpeggio Hold parameter on and off

for each Part.

If any of the [13] – [16] lamps is turned on, the Arpeggio

Hold parameter of the corresponding Part is turned on.

Changing the timbre of the Voice

Just as in the Voice mode, the sound of the Performance

(consisting of a maximum of four Parts or Voices) can be

edited via the Knobs in the Performance mode. There are

two ways to edit the Performance: editing the entire

Performance, and editing only one specific Part (Voice)

assigned to the Performance.

To edit the entire Performance:

Turn the Knob in the Performance Play mode (called up via

only the [PERFORM] button) or Performance Common Edit

mode (called up via [PERFORM]  [EDIT]  [COMMON]).

To edit a specific Voice of the current

Performance:

Turn the Knob in the Performance Part Edit mode (called up

via [PERFORM]  [EDIT]  [1] – [4]).

Turning Arpeggio playback on/off for each

Part

Turning the Arpeggio Hold parameter on/off

for each Part

Knob 1 Knob 2 Knob 3 Knob 4

Knob 5 Knob 6 Knob 7 Knob 8

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Recording in the

Performance mode

While experimenting and playing around with Arpeggios in

the Performance mode, you may find some rhythm patterns

and phrases that you like, and you may want to store them

for future recall. The best and easiest way to capture these is

to record your keyboard playing to a Song or Pattern.

Song and Pattern

Songs and Patterns are MIDI sequence data consisting of

up to 16 Tracks.

Song

A Song on this instrument is effectively the same as a song

on a MIDI sequencer, and playback automatically stops at

the end of the recorded data.

Pattern

In this instrument, the term “Pattern” refers to a relatively

short musical or rhythmic phrase — 1 to 256 measures —

which is used for looped playback. Therefore, once Pattern

playback starts, it continues until you press the [J] (Stop)

button.

Recording the melody and

Arpeggio playback to the Song

When a Song is selected as the destination of Performance

recording, you can record your keyboard playing with the

Arpeggio without having to worry about measure limits or

running out of recording space. It is a good idea, for example,

to record your keyboard playing, freely calling up various

Arpeggio types, then editing the Song later as necessary.

You may even want to keep the recorder ‘running’ as you

improvise, then listen back later and pick out the best parts

to create your final Song. Try recording as shown in the

instructions below.

In the Performance Play mode, select a Performance

for recording.

2 Press the ARP [ON/OFF] button so that the lamp

lights.

HINT

You can use the following operation to adjust the volume and

pan settings of Parts 1 – 4:

1 Press the Knob Function 1 button (at the left of Knobs 1

– 4) and Knob Function 2 button (at the left of Knobs 5 –

8) simultaneously.

The six lamps light and the KNOB FUNCTION pop-up

window will appear.

2 Turn the desired Knob to adjust the setting.

Turning one of Knobs 1 – 4 changes the volume of Parts 1 –

4, respectively.

Turning one of Knobs 5 – 8 changes the pan of Parts 1 – 4,

respectively.

3 After completing editing, press the [EXIT] button to

return to the Performance Play display.

HINT

You can use the following operation to adjust the pitch of Parts

1 – 4:

1 Press the [EDIT] button in the Performance mode.

2 Press the Number [1] – [4] button corresponding to the

Part you wish to edit.

3 Press the [F4] TONE button.

4 Press the [SF1] TUNE button.

5 Change the NoteShift value to adjust the pitch.

6 After completing editing, press the [EXIT] button to

return to the Performance Play display.

Volume for

Parts

1 – 4

Knob Function 1 button

Knob Function 2 button

Pan for

Parts

1 – 4

Knob 1 Knob 2 Knob 3 Knob 4

Knob 5 Knob 6 Knob 7 Knob 8

MOXF6/MOXF8 Owner’s Manual

Quick Guide

3 Press the [REC] button to call up the Performance

Record mode.

4 Set the following parameters on each of the

Performance Record displays.

[F1] SETUP display

“SeqMode” = “song”

This setting lets you record your keyboard performance

to the Song.

“Number”

Select a destination Song. Executing Performance

recording overwrites and erases all the previously

recorded data of the specified Song. Make sure to select

a Song which contains no data.

“TimeSignature” = “4/4”

Set the same value here as that of the Arpeggio type.

Normally, set this to “4/4.”

“Tempo”

Set the desired tempo of the metronome and Arpeggio

for recording.

[F2] REC TR display

“RecTrack”

Select the destination Tracks from “1 – 4,” “5 – 8,” “9 – 12,”

and “13 – 16.”

[F3] OTHER display

“KeyOnStart” = “on”

When set to “on,” recording starts immediately when you

press any note on the keyboard. Set this parameter to “on”

when using the Arpeggio.

“CopyPerfParam” = “on”

Set this to “on” when you wish to copy the parameter

settings for the Performance Parts 1 – 4 to the destination

Parts of the Song.

“MoveToRecMode” = “on”

Set this to “on” when you wish to move to the Song mode

(specified via the SeqMode) after recording ends.

[F5] CLICK

(click on)

Press the [F5] button to turn the metronome on if you wish

to use the metronome.

5 Press any note to start recording.

Play the keyboard in time with the metronome. You can

change the Arpeggio type and settings by pressing any of

the [SF1] – [SF6] buttons while recording.

6 Press the [J] (Stop) button to stop recording.

Recording stops and the instrument enters the Song mode.

After recording, the created data will be automatically stored

to internal Song/Pattern memory. Press the [F] button to

hear your newly recorded performance.

Record your keyboard performance to additional Tracks in

Song Record as desired, and edit the recorded data in the

Song Edit or Song Job to finalize the Song data.

NOTE

Regarding Arpeggios, not only the played notes but also all

note events of Arpeggio playback will be recorded.

7 After completing, press the [STORE] button to

store the Song.

Recording Arpeggio playback to a

Pattern

If you record your keyboard playing along with Arpeggio

playback in the Performance mode to a Pattern, you can

quickly create full and complete rhythm patterns lasting just

a few measures. These short Patterns of MIDI sequence

data can be played back repeatedly in a loop and then

conveniently used as ‘building blocks’ for your original

Songs.

The Performance Recording to a Pattern operation is the

almost same as that of Recording to a Song, with the

exception of the settings below.

In the Performance Record display, set the “Section” and

“SectionLength” as well as the same settings as in

“Recording the melody and Arpeggio playback to the Song.”

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Section

From A – P, select the Section which comprises the Pattern. If

you create several Sections, you can use them as rhythm

variations within a single Song.

Section Length

Set the length of the selected Section. Set the value to 1 – 4

according to the length of the current Arpeggio types.

After creating the Pattern Sections, program their playback

order to create a Pattern Chain. For details, see page 49.

Connecting a microphone

or audio equipment

Playing the keyboard along with

the sound input from the A/D

INPUT [L]/[R] jacks

You can have the A/D input sound—such as your voice

through a microphone, a guitar, bass, or CD player—assigned

as an Audio Input Part. Various parameters such as volume,

pan, and effect can be set to this Part and the sound is output

together with the sound of your keyboard performance. In

these example instructions, you’ll learn how to use the A/D

input sound in the Voice mode.

1 Make sure to turn off the power of this instrument

and set the A/D INPUT [GAIN] knob to the minimum.

2 Connect the audio equipment or the microphone

to the A/D INPUT [L]/[R] jack on the rear panel.

NOTE A standard dynamic microphone is recommended. (This

instrument does not support phantom-powered condenser

microphones.)

3 Turn on the connected audio equipment, then turn

on the MOXF6/MOXF8.

4 Press the [VOICE] button to enter the Voice Play

mode.

MOXF6/MOXF8

Stereo audio equipment (CD player, etc.)

A/D INPUT

[R]

A/D INPUT

[L]

MOXF6/MOXF8

Microphone

A/D INPUT

[L]/[R]

MOXF6/MOXF8 Owner’s Manual

Quick Guide

5 Press [UTILITY]  [F3] VCE A/D  [SF1] OUTPUT,

then set the “Mono/Stereo” parameter.

This parameter determines the signal configuration for the

audio signal via the A/D INPUT [L]/[R] jacks, or how the signal

or signals are routed (stereo or mono).

When connecting the audio device as shown in step 2, set

this parameter to “stereo” or “LRMono.” When connecting

the microphone as shown in step 2, set this parameter to

“LMono.”

If necessary, set the other parameters.

NOTE For details about the parameters including Mono/Stereo,

see the “Reference Manual” PDF document.

NOTE The above parameter settings including Mono/Stereo are

applied to the entire Voice mode. If necessary, press the

[STORE] button to store these with the Utility settings.

NOTE The above parameter settings including Mono/Stereo differ

depending on the selected mode.

NOTE

For the Performance mode, set the above parameters on the

display called up via [PERFORM]

 [EDIT]  [COMMON]

 [F5] A/D IN  [SF1] OUTPUT. The settings will be stored

for each Performance.

For the Song/Pattern mode, set this parameter on the display

called up via [SONG] or [PATTERN]

 [MIXING]  [EDIT]



[COMMON]



[F5] A/D IN



[SF1] OUTPUT. The settings

will be stored for each Song/Pattern.

6 Press [UTILITY]  [F1] GENERAL  [SF6] OTHER,

then set the “Mic/Line” parameter according to

the equipment connected to the A/D INPUT [L]/[R]

jacks.

When connecting equipment of low output level (such as a

microphone, guitar, bass), set this parameter to “mic.” When

connecting equipment of high output level (such as a

synthesizer keyboard, CD player), set this parameter to “line.”

NOTE This setting is available for all modes. If necessary, press

the [STORE] button to store this with the Utility settings.

7 Press the A/D INPUT [ON/OFF] button so that its

lamp lights.

This setting enables audio signals to be input from the

connected audio device.

8 Press the [LEVEL] meter button so that the

[A/D

INPUT] lamp lights, then adjust the input level

using the [GAIN] knob.

NOTE Adjust the [GAIN] knob to raise the input level as far as

possible without allowing distortion to occur.

9 Press the [VOICE] button, then select the desired

Voice.

Play the keyboard wile you sing into the microphone or play

back the audio equipment.

10 If necessary, press the [STORE] button to store

the Voice.

Playing the keyboard along with

Vocoder

This instrument features a Vocoder function. This is a

distinctive, “robot voice” effect which extracts the

characteristic of the microphone sound and adds it to the

sound of your keyboard performance. In these example

instructions, you’ll learn how to use the Vocoder in the Voice

mode.

NOTE For details about the Vocoder, see the “Reference Manual” PDF

document.

1 Connect the microphone by following steps 1 – 8

on the previous page.

2 Press the [VOICE] button, then select the desired

Voice to which the Vocoder is applied.

This instrument features special Voices specifically designed

for use with the Vocoder. Call up the Category Search display

then select the desired Voice from the “Vocoder” Main

Category.

NOTE

If you use the Vocoder effect in the Performance/Song/Pattern

mode, assign the Voice for the Vocoder to Part 1. Vocoder

cannot be applied to any of the other Parts.

[LEVEL] meter button

[LEVEL] meter

MOXF6/MOXF8 Owner’s Manual

Quick Guide

3 Press [EDIT]  [COMMON]  [F6] EFFECT  [SF1]

CONNECT, then set the “InsEF Connect” parameter

to “vocoder.”

NOTE The “InsEF Connect” parameter is automatically set to

“vocoder” if you select a Voice from the Vocoder Category in

step 2.

4 From the [SF2] VOCODER display, set the Vocoder

related parameters if necessary.

Speak or sing into the microphone while pressing the note(s)

to generate the machine-like Vocoder sound. Set the related

parameters as desired while listening to the Vocoder sound.

For details about each parameter, see the “Reference Manual”

PDF document.

5 Press the [STORE] button to call up the Store

display then store the settings as a User Voice.

Creating an original Song

This instrument features a built-in multi Track sequencer for

recording your keyboard performance as MIDI data. This

function by itself is enough to create full, complex multi-

instrument arrangements and complete Songs.

Terminology

Song and Pattern

See page 36.

Track

This is a memory location on the sequencer where your

musical performances (made up of MIDI events) are stored.

The MOXF6/MOXF8 provides 16 Tracks, which correspond

to the 16 Parts of the Mixing.

Mixing

This is a program in which multiple Voices are assigned to

Parts for multi-timbral play in the Song and Pattern modes.

Each Mixing can contain up to 16 parts and a separate

Mixing can be created for each Song.

Realtime Recording

With Realtime recording, the instrument functions in the same

way as a MD recorder, recording the performance data as it

is played. This allows you to capture all the nuances of an

actual performance. Realtime Record features three available

methods: Replace, Overdub and Punch In/Out. Replace lets

you overwrite an already recorded Track with new data.

Overdub lets you add more data to a Track that already

contains data. Punch In/Out lets you re-record only over a

specific area of the Track.

Step Recording

With Step recording, you can compose your performance by

“writing” it down one event at a time. This is a non-realtime,

step recording method — similar to writing music notation

onto paper.

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Song playback

You have already learned how to play back Songs on

page 19. In this section, you’ll learn how to use convenient

mute/solo functions during playback.

This lets you mute a specific Track or Tracks of the Song.

1 Press the [MUTE] button so that its lamp lights.

The lamps of the Number buttons light, indicating that the

corresponding Tracks are on.

2 To mute a Track, press the corresponding Number

[1] – [16] buttons (the lamp turns off).

Multiple Tracks can be muted simultaneously.

3 To sound a muted Track, press the corresponding

button (lamp is off) so that its lamp lights.

For future recording purposes, make sure all buttons are lit

and Mute is turned off for all Tracks.

This lets you solo a specific Track of the Song.

1 Press the [SOLO] button so that its lamp lights.

2 To solo a Track, press the corresponding Number

[1] – [16] buttons (the lamp flashes).

Press another number button to change the soloed Track.

3 Press the [TRACK] or [MUTE] button to return to

the original status.

Creating a Drum part via Step

Recording

Now, try creating a Song.

First, record a 4-measure drum phrase as shown below to

Track 1 by using Step Recording.

1 Press the [SONG] button to call up the Song Play

display then select an empty Song.

2 On the [F1] PLAY display, set the time signature to

“4/4.”

3 Press the [REC] button, followed by the [F1]

SETUP button, then set the parameters as below.

• Type = step

• Event = note

•RecTr = 1

• Ch = all

If necessary, set the tempo to the desired value.

Press the [F2] VOICE button, followed by the

[CATEGORY SEARCH] button, then select the

Drum Voice.

Set the Main Category to “Drum/Percussion” then set the Sub

Category to “Drums.” Move the Cursor [>] button to call up

the Drum Voice List. From this list, select “PDR B09 Analog”

then press the [ENTER] button.

Track mute

Track solo

[MUTE] buttonNumber [1] – [16] buttons

[SOLO] buttonNumber [1] – [16] buttons

Time signature

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Press the [

] (Play) button to enter the Step Record

mode.

The [F] button lamp lights and the Step Record display

appears.

6 Set the “Step Time” to “480.”

The “Step Time” parameter determines to what position the

pointer will advance after a note has been entered. Here,

the pointer will advance in quarter-note steps.

7 Press the [P] (Top) button to return to the top of

the Song, then press the B0 key four times.

The Bass Drum Kick sound (assigned to the B0 key) is

recorded to the timing of each beat.

NOTE

If you are using the MOXF6, use the [OCTAVE] buttons to

make sure that the Bass Drum Kick sounds when you play

the B0 key. This is necessary since the MOXF6 has a

shorter keyboard and doesn’t have a B0 key.

8 Press the [J] (Stop) button to stop recording.

This returns to the Song Play display.

9 To record another percussion sound, press the

[REC] button then the [F] (Play) button to enter

the Step Record mode again.

The [F] button lamp lights and the Step Record display

appears.

10 Set the “Step Time” to “ 240.”

The Step Time parameter determines to what position the

pointer will advance after a note has been entered. Here,

the pointer will advance in eighth-note steps.

11 Press the [

] (Top) button to return to the top of

the Song, then press the [F3] REST button and

G 1 key four times.

An eighth-note rest is recorded to each down beat and the

Hi-Hat Cymbal sound (assigned to the G 1 key) is recorded

to each up beat.

NOTE

If you are using the MOXF6, use the [OCTAVE] buttons to

make sure that the Hi-Hat Cymbal sounds when you play

the G 1 key. This is necessary since the MOXF6 has a

shorter

keyboard and doesn’t have a G 1 key.

12 Press the [J] (Stop) button to stop recording.

This returns to the Song Play display.

After executing the above operations (steps 1 – 12), you

should now have a 1-measure drum phrase as shown below.

Press the [

] (Top) button, then press the [

]

(Play)

button to hear the recorded data.

To stop playback, press the [J] (Stop) button.

Press the [JOB] button, followed by the [F3] EVENT

button to call up the EVENT JOB SELECT display.

To create a four-measure drum pattern (which repeats the

recorded drum phrase), use the Copy Event Job.

15 Select “02: Copy Event” then press the [ENTER]

button.

16 Make the settings as listed below then press the

[ENTER] button to execute the Copy Event Job.

• Source Track = “01”, Source range =

“001:1:000” – “002:1:000”

• Destination Track = “01”, Top measure of the destination =

“002”

• “NumberOfTimes” = “x 03”

Executing this Job will copy the drum phrase (recorded to

the first measure) to the 2nd, 3rd, and 4th measures

respectively.

17 Press in order the [SONG] button, [P] (Top)

button, and [F] (Play) button to hear the recorded

data.

To stop playback, press the [J] (Stop) button.

HINT

Tips in Step Recording

• In Step recording, you can also enter chords. Because notes

are actually entered when the keys are released, make sure

to press all correct keys you want to enter then release the

keys.

•

In Step Recording, press the [

] (Play) button to start playback

from the current position. In this status, pressing the [

] (Stop)

button will stop playback and return to the Step Record mode.

• In Step recording, you can create the legato phrases by

setting the GateTime to “100%.”

• In Step Recording, you can enter tied notes. For example,

first set the Step Time to “480” (quarter note) then press and

release the key. Next, change the Step Time to “240” (8th note)

then press the [F4] TIE button, resulting in a dotted quarter

note.

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Creating a bass part via Realtime

Recording

Next, record the bass line via Realtime Recording to Track 2.

1 In the Song Play mode, select the same Song

(created above) to which the Drum part has

already been recorded.

2 Press the [REC] button, followed by the [F1]

SETUP button, then set the parameters as below.

• “Type” = “replace”

• “Quantize” = “240”

• “RecTr” = “2”

3 Press the [F2] VOICE button, followed by the

[CATEGORY SEARCH] button then select the Bass

Voice.

Set the “Main” (Main Category) to “Bass” then set the “Sub”

(Sub Category) to “Synth Bass.” Move the Cursor [>] button

to call up the Voice List. From this list, select “PRE3 E01 Uni

Punch” then press the [ENTER] button.

4 Press the [F5] CLICK button to turn the Click

() on.

5 Press [UTILITY]  [F2] SEQ  [SF1] CLICK, then

set the Click related parameters as below.

• “Mode” = “rec”

• “Beat” = “04”

• “RecCount” = “1meas”

With this setting, there will be a one-measure lead-in count

before recording begins and the Click will play back only

while recording.

6 Press the [REC] button to return to the Song

Record display.

7 Press the [P] (Top) button to return to the top of

the Song, then press the [F] (Play) button to start

recording.

As soon as the lead-in count (1-measure) is finished, play

the following notation.

8 After playing the above notation, press the [J]

(Stop) button to stop recording.

If you play any wrong notes, press the [J] (Stop) button,

then try recording again. Repeat as often as necessary until

you get it right.

9 Press the [P] (Top) button followed by the [F]

(Play) button to hear the recorded data.

The recorded data of the Tracks 1 and 2 will be played back.

To stop playback, press the [J] (Stop) button. If you are not

satisfied with the recorded data, try this operation again.

HINT

Re-recording a specific part of a Song

(Punch In/Out)

Use the Punch In/Out recording method to record over only a

specific portion of the Track. If you set the start point (Punch In)

and end point (Punch Out), and then start recording from the

top of the Song, the actual recording will be done only between

the Punch In and Punch Out points. In the eight-measure

example below, only the third through the fifth measures are re-

recorded.

NOTE Punch In/Out Recording can only be used with Realtime

recording.

NOTE

Note that the Punch In/Out method always replaces

(destroys) the original data over the specified area.

To execute Punch In/Punch Out recording in the above condition,

set the following parameters beforehand on the [F1] SETUP

display in the Song Record mode.

• “Type” = “punch”

• Punch In = 003:01

• Punch Out = 006:01

1234567 8

Recording start Recording stop

Before re-recording

Punch In point Punch Out point

After re-recording

Newly recorded data

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Creating a synthesizer part by

using Arpeggio

Next, record Arpeggio playback via Realtime Recording to

Trac k 3.

1 In the Song Play mode, select the same Song to

which the Drum and Bass parts have already been

recorded.

2 Press the ARP [ON/OFF] button so that its lamp

lights.

3 Press the [REC] button, followed by the [F1]

SETUP button, then set the parameters as below.

• “Type” = “replace”

• “Quantize” = “off”

• “RecTr” = “3”

4 Press the [F2] VOICE button, followed by the

[CATEGORY SEARCH] button then select the

Synthesizer Voice.

Set the Main Category to “Synth Pad / Choir” then set the

Sub Category to “Analog.” Move the Cursor [>] button to call

up the Voice List. From this list, select “PRE5 H04 Saw Pad”

then press the [ENTER] button.

5 Press ARP [EDIT] or [F3] ARP ED  [F3] MAIN,

then set the Switch parameter to “on” and set the

“VoiceWithARP” parameter to “off.”

With the “Switch” parameter “on,” the Arpeggio of Track 3

can be played back.

If the “VoiceWithARP” parameter is set to “on,” selecting the

Arpeggio Type will change the Voice from the one selected

in step 4. This is why you should set the “VoiceWithARP”

parameter to “off” here.

6 Press [F2] TYPE  [SF1] ARP1, then assign the

Arpeggio Type to the [SF1] ARP1 button.

On this display, set the parameters as below:

• “Bank” = “Pre”

• “Category” = “Seq”

• “SubCategory” = “Genrl”

• “Type” = “7483”

If desired, assign different Arpeggio Types to the [SF2] –

[SF6] buttons.

NOTE

For instructions on using the Location settings, see the

“Reference Manual” PDF document.

HINT

Rehearsing function while recording

During Realtime Recording in the Song/Pattern mode, pressing

the [REC] button will call up the “Rehearsal” mode. In this

mode, the [REC] indicator will flash and playback will continue

uninterrupted; however, no data will be recorded, letting you

practice a part or try out various ideas (while listening to the

other tracks) without actually recording. To return to the Record

mode, press the [REC] button again—the [REC] indicator will

light continuously.

Punch Out point

Recording ends at this point and normal

playback of the recording Track starts.

Punch In point

Playback of the recording Track is turned off from this point,

and your keyboard performance will be recorded to the Track.

[SF1] COPYLOC button

Press the [SF1] COPY LOC to assign the measure numbers

registered to the Locations (Loc1 and Loc2) to the Punch

In and Punch Out points.

Recording

Rehearsal mode

(playback continues)

MOXF6/MOXF8 Owner’s Manual

Quick Guide

7 Press the [REC] button to return to the Song

Record display.

8 Press the [P] (Top) button to move to the top of

the Song then press the [F] (Play) button to start

recording.

The [F] (Play) button lamp lights and “RECORDING”

appears at the top of the display, indicating that the

Recording has already started. After the one-measure lead-

in count is finished, play the following notation.

NOTE

All the notes generated via Arpeggio playback will be

recorded.

9 After playing the above notation, press the [J]

(Stop) button to stop recording.

If you play any wrong notes, press the [J] (Stop) button,

then try recording again. Repeat as often as necessary until

you get it right.

10 Press the [

] (Top) button, followed by the [F]

(Play) button to hear the recorded data.

The recorded data of Tracks 1, 2 and 3 will be played back.

To stop playback, press the [J] (Stop) button. If you are not

satisfied with the recorded data, try this operation again.

Correcting wrong notes

If you’ve played any wrong notes while recording and wish to

correct them, press the [EDIT] button from the Song Play

mode to go to the Song Edit mode. Song Edit lets you clean

up and edit data of already recorded Songs or insert new

data to the Songs. Check for any mistakenly recorded or

wrong events on the event list display of the Song Edit mode,

then correct them as needed.

1 With the recorded Song selected, press the [EDIT]

button to enter Song Edit, then press the [F1]

CHANGE button.

The CHANGE display appears.

2 Press the desired Track number button (from [1] –

[3]).

The list of the MIDI events recorded to the selected Track in

the previous section appears on the display.

NOTE

The Song location at which you edit or input the event is

indicated by measure, beat and clock. A quarter note (one

beat when the time signature is set to “4/4”) consists of 480

divisions. The length of each note (gate time) is indicated by

Beat and Clock. For example, 001:000 is equivalent to a

quarter note and 000:240 is equivalent to an eighth note.

3 Use the Cursor buttons to move the cursor to the

location to be edited, then turn the [DATA] dial to

edit the value.

When you change the value at the current line, the entire line

starts flashing.

4 Before moving the cursor to another line, press

the [ENTER] button to fix the value.

The edited event line stops flashing.

5 As necessary, correct the other data.

If you find unnecessary notes (not described on the notation),

move the cursor to the corresponding position then press

the [F6] DELETE button.

6 After completing editing, press the [EXIT] button

to return to the Song Play display.

To confirm the recorded data, press the [P] (Top) button,

followed by the [F] (Play) button to start playback. To stop

playback, press the [J] button.

Completing the Song by editing

the Mixing

In this final step (other than storing your precious work,

which we’ll cover next), you can mix down your Tracks with

the Song Mixing function – adjusting the volume balance

and pan setting of all the parts and tweaking the effect

levels.

NOTE The explanations here also apply to the Pattern mode.

1 Press the [SONG] button to enter the Song Play

mode, then select the desired Song.

2 Press the [MIXING] button to enter the Mixing

mode, then set various parameters.

The [MIXING] button lamp lights and the Mixing display will

appear. Select the menu you wish to edit by pressing the

[F1] – [F4] buttons, then edit the parameters in each display.

For details about each parameter, see the “Reference

Manual” PDF document.

Location Notes Gate time Velocity

Indicates that the Mixing parameter

is modified but not stored yet.

Mixing Play display

MOXF6/MOXF8 Owner’s Manual

Quick Guide

3 Press the [EDIT] button to enter the Mixing Edit

mode.

4 Call up the Common Edit display or Part Edit

display.

Use Part Edit to edit the parameters for each Part. Use

Common Edit to edit the parameters for all of the Parts.

5 Select the menu you wish to edit by pressing the

[F1] – [F6] buttons and [SF1] – [SF6] buttons, then

edit the parameters in each display.

For details on each parameter, see the “Reference Manual”

PDF document.

6 Repeat steps 4 – 5 as desired.

7 Press [STORE]  [F1] SEQ  [ENTER] to store the

settings as Song data.

This operation will store all the Songs and Patterns at the

same time.

NOTICE

If you are editing Mixing parameters and you select a different Song

without storing the one being edited, all the edits you've made will be

erased.

Storing the created Song

After creating a Song, assign a name to the Song then

execute the Store operation.

1 Press [SONG]  [JOB]  [F6] SONG to call up the

Song Job List.

2 Select “04:Song Name,” press the [ENTER] button

to call up the Song Name display, then enter the

Song name.

Move the Cursor to the desired position then enter the

character by holding the [SF6] CHAR button. Repeat this

operation as often as necessary to create the name.

NOTE

For specific instructions on naming, see Basic Operation on

page 22.

3 After naming, press the [ENTER] button to actually

enter the name.

4 P

ress the [STORE] button, followed by the [F1] SEQ

button.

The Store display appears.

5 Press the [ENTER] button to store the Song.

This operation will store all the Songs and Patterns at the

same time.

After storing, press the [EXIT] button to exit from the Store

display.

NOTE

ong/Pattern data consists of MIDI sequence data and

Mixin

g data. MIDI sequence data is recorded by playing the

keyboard while Mixing data is created by editing the

parameters.

HINT

Storing Mixing settings as a template

The Mixing settings you make can be stored as a

Template—letting you create your own custom Mixing/Voice

configurations for future use in recording Songs. This operation

can be done on the display called up via [SONG]  [STORE]

 [F2] TEMPLATE. For detailed instructions, see the

“Reference Manual” PDF document.

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Creating an original Pattern

The Pattern mode also lets you record your rhythm patterns

or riffs to the different Sections as you wish—and as the

inspiration hits—then combine the Sections into a Pattern

Chain to create a complete Song. Along with the Arpeggio

feature and Performance recording, you have a wide range

of easy-to-use tools to quickly create fully arranged,

professional sounding Songs.

Listening to the Demo Patterns

Before creating your own original pattern, you should give a

listen to some of the preset Demo Patterns. These specially

recorded Patterns cover a wide range of musical genres and

are full of great hints and ideas on how you can create and

use Patterns in your own music.

1 Press the [PATTERN] button to enter the Pattern

mode.

The Pattern Play display will appear.

2 Select a Pattern by turning the [DATA] dial.

3 Press the [F] (Play) button to start playback of the

Pattern.

The Pattern will play back repeatedly until you press the [J]

(Stop) button.

4 Press the [PATTERN SECTION] button then

change Sections, selecting from A – P.

Pressing the [1] – [8] buttons calls up Sections A – H and

pressing the [9] – [16] buttons calls up Sections I – P.

NOTE

By changing the Sections, you can create rhythmic variations

and easily improvise arrangements (such as intro, verse,

chorus, verse, chorus, ending) in real time.

Creating a Pattern (Section A) by

using Arpeggio

In addition to creating a Pattern by recording your keyboard

performance conventionally, you can also use the powerful

Arpeggio playback features of this instrument.

Here, create data for Section A by recording Arpeggio

playback to Track 1 as the drum part, Track 2 as the guitar

part and Track 3 as the bass part.

1 Press the [PATTERN] button to enter Pattern Play

then select a Pattern.

2 Press the [PATTERN SECTION] so that its lamp

lights then press the Number [1] button to select

Section A.

On the Pattern Play display, set the Pattern Length,

Time Signature and Tempo.

4 Press the [TRACK] so that its lamp lights then

press the Number [1] button to select Track 1.

5 Press ARP [EDIT]  [F3] MAIN, then set the

“Switch” parameter to “on” and set the

“VoiceWithARP” parameter to “on.”

With the “Switch” parameter “on,” the Arpeggio of Track 1

can be played back. When the Arpeggio Type is selected

with the “VoiceWithARP” parameter “on,” the Voice

appropriate for the selected Arpeggio Type will be

automatically called up.

6 Press the ARP [ON/OFF] button so that its lamp

lights.

1st measure

120th measure

Intro

Melody A

Melody B

Main theme

Melody B

Main theme

Ending

Section A

Section B

Section C

Section D

Section E

Section F

Section G

Section A – H [PATTERN SECTION] button

Section I – P

Time Signature Tempo Length

MOXF6/MOXF8 Owner’s Manual

Quick Guide

7 Press the [F2] TYPE button then select the

desired Arpeggio Type assigned to the [SF1] –

[SF6] buttons.

Changing the Arpeggio Type will call up a different Voice

since the “VoiceWithARP” parameter is set to “on.” If you want

to record a drum pattern, for example, set the Category to a

drum/percussion-like name then find the desired Arpeggio

Type.

8 Press the [REC] button then set the parameters

for recording on the [F1] SETUP display as below.

• “Type” = “replace”

• “Loop” = “off”

• “Quantize” = “off”

Set the other parameters if necessary.

9 Press the [F5] CLICK button to set the click to on

().

10 Press the [F] (Play) button to start recording.

Play the keyboard to trigger Arpeggio playback. Since the

“Loop” parameter is set to “off,” recording will be finished

automatically when the end of the Pattern Length is

reached.

NOTE

All the notes generated via Arpeggio playback will be

recorded.

11 Press the [F] (Play) button to hear the recorded

Phrase.

12 Record Phrases to the other Tracks of Section A

as desired using the same operation.

Record a bass line to Track 2, then record guitar backing to

Track 3 by repeating steps 4 – 11 above.

13 Press [STORE]  [F1] SEQ  [ENTER] to store the

recorded Phrases as a Pattern.

This operation will store all the Song/Patterns.

Now that you’ve recorded Section A, go on to the following

instructions and create Section B by using the Pattern Copy

Job with the already recorded User Phrases.

Creating another Pattern (Section

B) by using already recorded data

Here, you’ll learn how to create a Section B by using recorded

data copied from Section A. For example, the drum part and

bass part will be copied from Section A, and the guitar part

will be created via the same note data as that of the bass part.

First, copy all the recorded data from the Section A to Section

B by using the Pattern Copy Job.

1 Press [PATTERN]  [JOB] to enter the Pattern Job.

2 Press the [F6] PATTERN button, select “01: Copy

Pattern” then press the [ENTER] button.

The Copy Pattern Job display appears.

3 Select the Pattern number and Section to be

copied.

For the copy source, select the Pattern number and Section

which you have already recorded in the previous section.

For the copy destination, select the same Pattern number

and “Section B.”

4 Press the [ENTER] button to execute the Pattern

Copy Job.

All the data of Section A will be copied to Section B.

5 Press the [EXIT] button a few times to return to

Pattern Play.

Recorded Data as a User Phrase

The MIDI note sequence data (except for the Voice setting,

etc.) recorded in the Pattern mode will be stored as a User

Phrase. The stored User Phrase can be assigned to a different

Section/Track from the [F4] PATCH display in the Pattern Play

mode. This allows you to use already recorded User Phrases

for the other different Sections/Tracks. A single Pattern provides

memory space for 256 of your own original User Phrases.

Copying the Pattern data

Source Destination

MOXF6/MOXF8 Owner’s Manual

Quick Guide

6 Press the [PATTERN SECTION] button so that its

lamp lights then press the Number [2] button.

Section B is now selected. Press the [F] (Play) button to

hear Section B and confirm that the Section B data has been

copied from Section A.

Have the guitar and bass play together by using the user

phrase of the bass recorded in Section A.

7 Press the [F4] PATCH button to call up the PATCH

display.

8 To Track 3 (guitar part), assign the same Phrase as

that of Track 2 (bass part).

This operation will have the guitar (Track 3) and bass (Track

2) play the same Phrase in unison.

9 Press the [F] (Play) button to hear the recorded

Phrase.

If necessary, adjust the octave setting or velocity setting of

the guitar part by using the [F2] NOTE Jobs. For details

about the available parameters, see the “Reference

Manual” PDF document.

NOTICE

If a specific Phrase is assigned to various Sections/Tracks, keep in

mind that editing the Phrase will change the playback sound of all

Sections/Tracks that use this Phrase.

10 Press [STORE]  [F1] SEQ  [ENTER] to store the

recorded Phrases as a Pattern.

This operation will store all the Song/Patterns.

After recording Section B, create other Sections as desired.

As in the Song mode, you can also use Step Recording to

create Patterns.

Creating a Pattern Chain for

converting to a Song

In these instructions you’ll learn how to assign each of the

created Pattern Phrases to the Section, arrange the Sections

in your favorite order to create the Pattern Chain, and

convert the Pattern Chain to a Song. This converted Song

data can be used as backing accompaniment for melody

recording.

This section explains how to create a Pattern Chain by

arranging the Sections in order as shown in the example

above.

1 In the PLAY display of the Pattern Play mode,

select the Pattern created in the previous section.

2 Press the [F6] CHAIN button.

Assign the already recorded data

(User Phrase)

HINT

Pattern Patch display

On the Pattern Patch display, only the User Phrase contained

in the current Pattern can be assigned to any Track. If you wish

to use Phrases belonging to other Patterns, follow the

instructions below:

1 Press the [SF6] COPY button.

2 Select the desired Phrase as the copy source.

3 Select the User Phrase number and Track number as the

copy destination.

4 Press the [ENTER] button to execute the Copy operation.

The amount of measures

Phrase number

Assign the same Phrase as that of Track 2.

Creating a Pattern Chain

.......

Pattern Chain

Change the Sections as desired to create the Song you have in mind…

Section A Section B Section F Section H

Song

MOXF6/MOXF8 Owner’s Manual

Quick Guide

3 Press the [REC] button to enter the Pattern Chain

Record mode then set the Recording Track and

Pattern tempo.

Three Pattern Chain Track types are available. The Tempo

Track lets you record tempo changes for the Chain, and the

Scene Track lets you record Track on/off changes. The Pattern

(“patt”) Track lets you record Section changes at the desired

measure points in the Song. Here, set “RecTrack” to “patt.”

4 Press the [F] (Play) button to start recording then

play the Pattern.

Change the Sections as desired. You can “play” the Section

buttons as the Pattern plays back to create a new Song.

5 Press the [J] (Stop) button to stop recording.

The instrument returns to the CHAIN display of Pattern Play.

6 Press the [F] (Play) button to play the recorded

Pattern Chain.

7 Press [STORE]  [F1] SEQ  [ENTER] to store the

recorded Pattern Chain.

This operation will store all the Song/Patterns.

8 After pressing the [EXIT] button, record the Tempo

Track then Scene Track by repeating steps 3 – 7

above.

When you record the Tempo Track:

In step 3, set the RecTrack to “tempo.” In step 4, move the

cursor to the tempo column ( ) then change the tempo as

desired by using the [DATA] dial or [INC]/[DEC] buttons.

Tempo change timing will be recorded in real time to the

Tempo Track.

When you record the Scene Track:

In Step 3, set the RecTrack to “scene.” In step 4, press the

[MUTE] button so that its lamp lights then turn on/off the

desired Number buttons. The change timing of the on/off

status will be recorded in real time to the Scene Track.

The Pattern Chain Edit mode makes it possible to edit the

order of the Sections in a chain as well as inserting tempo,

and scene/mute event data.

1 In the Pattern Play mode, select the Pattern created

in the previous section.

2 Press [F6] CHAIN  [EDIT] to enter the Pattern

Chain mode, then edit each of the Tracks.

To select each Track, press the [F4] TR SEL button.

3 Press the [EXIT] button to return to the Pattern

Play display then press the [F] (Play) button to

start the Pattern Chain.

4 Press [STORE]  [F1] SEQ  [ENTER] to store the

recorded Pattern Chain.

This operation will store all the Song/Patterns.

1 In Pattern Play, select the Pattern created in the

previous section.

2 Press [F6] CHAIN  [EDIT] to enter the Pattern

Chain mode.

Section A – H

Section I – P

Editing the Pattern Chain

Converting a Pattern Chain to a Song

Pattern Track Edit

Scene Track Edit

Tempo Track Edit

[F4] button

MOXF6/MOXF8 Owner’s Manual

Quick Guide

3 Press the [F3] Song button to call up the “Convert

to Song” display, then select an empty Song and

the top measure for the destination.

4 Press the [ENTER] button to execute the

conversion.

The Pattern Chain data will be converted to Song data, and

the converted data will be copied to the top measure

specified in step 3.

NOTICE

This operation overwrites any data already existing at the destination

Song.

5 Press the [SONG] button, select the Song

specified in step 3, then press the [F] (Play) button

to hear the newly created Song data.

6 Press [STORE]  [F1] SEQ  [ENTER] to store the

created Song.

This operation will store all the Song/Patterns.

Connecting external MIDI

instruments

With a standard MIDI cable (available separately), you can

connect an external MIDI instrument, and control it from the

MOXF6/MOXF8. Likewise, you can use an external MIDI

device (such as a keyboard or sequencer) to control the

sounds on

the

MOXF6/MOXF8

. Below are several different

MIDI connection

examples; use the one most similar to your

intended setup.

NOTE Any one of these interfaces can be used for MIDI data

transmission/reception: the MIDI connectors, or the USB [TO

HOST] connector. However, they cannot be used at the same

time. Select which connector is to be used for MIDI data transfer

in the “MIDI IN/OUT” parameter of the [UTILTITY]  [F6] MIDI 

[SF4] OTHER display. As you work through the explanations in

this chapter, set “MIDI IN/OUT” to “MIDI” since MIDI is used as

the example connection here.

Controlling MOXF6/MOXF8 from an external MIDI

keyboard or synthesizer

Use an external keyboard or synthesizer to remotely select

and play the Voices of the MOXF6/MOXF8.

For the destination, select the Song and

the top measure.

If the “without PC” is checkmarked, executing this operation

will ignore the Program Change events in the Pattern data.

MIDI [IN]

MOXF6/MOXF8

MIDI [OUT]

External MIDI keyboard such as an 88-key synthesizer

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Controlling an external MIDI keyboard or

synthesizer from the MOXF6/MOXF8

This connection lets you sound an external MIDI tone

generator (synthesizer, tone generator module, etc.) by

playing the MOXF6/MOXF8 or playing back the Song/Pattern

the

MOXF6/MOXF8

. Use this connection when you wish to

sound

the other instrument as well as the MOXF6/MOXF8.

HINT

MIDI Transmit Channel and Receive Channel.

Make sure to match the MIDI Transmit Channel of the external

MIDI instrument with the MIDI Receive Channel of the MOXF6/

MOXF8. For details on setting the MIDI Transmit Channel of the

external MIDI instrument, refer to the owner’s manual of that

instrument. For details on setting the MIDI Receive Channel of

the MOXF6/MOXF8, check the following points.

In the Voice mode/Performance mode (using the MOXF6/

MOXF8 as a single timbre tone generator):

Check the MIDI Basic Receive Channel with the following

operation: [UTILITY]  [F6] MIDI  [SF1] CH (channel) 

“BasicRcvCh.” If necessary, change this parameter to the same

number as the MIDI Transmit Channel of the external MIDI

instrument.

In the Song mode/Pattern mode (using the MOXF6/MOXF8

as a multi-timbral tone generator):

Check the MIDI Receive Channel for each Part of the Multi with

the following operation. [SONG]/[PATTERN]  [MIXING] 

[EDIT]  selection parts  [F1] VOICE  [SF2] MODE 

“ReceiveCh.” If necessary, change this parameter to the same

number as the MIDI Transmit Channel of the external MIDI

instrument. Please note that all parts whose MIDI Receive

Channels are the same as the MIDI Transmit Channel of the

external MIDI instrument are sounded by your keyboard

performance. Change the settings of the desired parts to match

the MIDI Transmit Channel settings on the external MIDI

instrument.

MIDI [OUT]

MIDI [IN]

External MIDI tone generator such as MOTIF-RACK XS

MOXF6/MOXF8

HINT

Splitting the sound between the MOXF6/MOXF8

and an external tone generator by MIDI channel

Using the connection example shown above, you can play both

instruments and have them separately sound different parts—

for example, having your keyboard performance sound the

external instrument while the Song/Pattern plays the sounds of

the MOXF6/MOXF8. To use this feature, you must set the

MOXF6/MOXF8

’s output channel and the external tone

generator’s receive

channel to the same channel number. Check

the following points

after turning the power on.

When playing the keyboard in the Voice mode or

Performance mode:

Check the MIDI transmit channel with the following operation:

[UTILITY]  [F6] MIDI  [SF1] CH (channel)  “KBDTransCh.”

If necessary, change this parameter to the same number as

the MIDI Receive Channel of the external MIDI instrument. In

the Voice play or Performance play, pressing the [TRACK]

button (so that the lamp lights) can also change the MIDI

Transmit Channel of the MOXF6/MOXF8. When you wish to

sound

only the external tone generator, set the [Master Volume]

control

to “0” or set Local Control to “off” with the following

operation: [UTILITY]  [F6] MIDI  [SF2] SWITCH 

“LocalCtrl” = “off.” For information on how to set the MIDI

Receive Channel of the external MIDI instrument, refer to the

owner’s manual of the external MIDI instrument.

When playing back a Song/Pattern or playing the keyboard

in the Song mode or Pattern mode:

Check the MIDI transmit channel for each Track with the

following operation: [SONG]/[PATTERN]



[F3] TRACK



[SF1]

CHANNEL  “OUT CH.” If necessary, change this parameter

to the same number as the MIDI Receive Channel of the external

MIDI instrument. Alternately, you can set the output destination

(Internal or external MIDI tone generator) for each Track from

the following display: [SONG]/[PATTERN]  [F3] TRACK 

[SF2] OUT SW. In this case, you’ll need to set the external MIDI

tone generator to multi-timbral operation and set the MIDI

Receive Channel for each part. For details, see the owner’s

manual of the external MIDI tone generator. Alternately, you can

have your keyboard performance split and assigned to

different MIDI channels by using the Zone settings in the Master

mode (page 57).

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Using a Connected

Computer

By connecting the MOXF6/MOXF8 to your computer via

USB, you can use DAW software on the computer to create

your own original songs.

NOTE The acronym DAW (digital audio workstation) refers to music

software for recording, editing and mixing audio and MIDI data.

The main DAW applications are Cubase, Logic Pro, SONAR and

Digital Performer. Though all of these can be effectively used

with the MOXF6/MOXF8, we recommend using Cubase when

creating songs together with the instrument.

By connecting this instrument to a computer, you can take

advantage of the following functions and applications.

• External tone generator for DAW software and MIDI

keyboard

• Remote Controller of the DAW software

• Editing parameters from the computer (MOXF6/MOXF8

Editor)

Connecting to a computer

A USB cable and the Yamaha Steinberg USB Driver are

necessary to connect the MOXF6/MOXF8 to the computer.

Follow the instructions below. Note that both audio data and

MIDI data can be transmitted through a USB cable.

1 Download the latest Yamaha Steinberg USB Driver

from our website.

After clicking the Download button, extract the compressed

file.

http://download.yamaha.com/

NOTE

Information on system requirements is also available at the

above web site.

NOTE The Yamaha Steinberg USB Driver may be revised and

updated without prior notice. Make sure to check and

download the latest version from the above site.

2 Install the Yamaha Steinberg USB Driver to the

computer.

For instructions on installing, refer to the online Installation

Guide included in the downloaded file package. When

connecting this instrument to a computer, connect the USB

cable to the USB TO HOST of this instrument and the USB

terminal of the computer as shown below.

3 Make sure that the USB [TO HOST] terminal of this

instrument is enabled.

Press the [UTILITY] button to call up the Utility mode, then

press the [F6] MIDI button followed by the [SF4] OTHER

button to call up the OTHER display. Set the “MIDI IN/OUT”

parameter to “USB.”

4 Set the input and output settings for audio data

and MIDI data as desired to suit your personal

preferences.

These settings can be set in the [F5] USB I/O display and

[F6] MIDI display of the Utility mode. Setting the parameters

related to the Audio data and MIDI data by using the Quick

Setup lets you instantly reconfigure the MOXF6/MOXF8 for

different computer/sequencer related applications by calling

up specially programmed presets. In this case, press the

[QUICK SETUP] button and then set the “SETUP.” After

making the settings, press the [ENTER] button to apply them

to the MOXF6/MOXF8.

NOTE

For details on the parameters set by the Quick Setup

function, see the “Reference Manual” PDF document.

5 Press the [STORE] button to store the settings to

internal memory.

USB terminal

USB [TO HOST] terminal

Rear panel

USB cable

Precautions when using the USB [TO HOST]

terminal

When connecting the computer to the USB [TO HOST] terminal,

make sure to observe the following points. Failing to do so risks

freezing the computer and corrupting or losing the data. If the

computer or the instrument freezes, restart the application

software or the computer OS, or turn the power to the instrument

off then on again.

NOTICE

• Use an AB type USB cable. USB 3.0 cables cannot be used.

• Before connecting the computer to the USB [TO HOST]

terminal, exit from any power-saving mode of the computer

(such as suspend, sleep, standby).

• Before turning on the power to the instrument, connect the

computer to the USB [TO HOST] terminal.

• Execute the following before turning the power to the

instrument on/off or plugging/unplugging the USB cable to/

from the USB [TO HOST] terminal.

• Quit any open application software on the computer.

• Make sure that data is not being transmitted from the

instrument. (Data is transmitted only by playing notes on

the keyboard or playing back a song.)

• While the computer is connected to the instrument, you

should wait for six seconds or more between these

operations: (1) when turning the power of the instrument off

then on again, or (2) when alternately connecting/

disconnecting the USB cable.

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Creating a Song with a computer

By using the MOXF6/MOXF8 with the DAW software on the

computer connected to the MOXF6/MOXF8, you can take

advantage of the following functions and applications.

• MIDI recording and Audio recording of the MOXF6/MOXF8

performance to the DAW software on the computer.

• Playing back a song of the DAW software by using the

MOXF6/MOXF8 tone generator

This section contains an overview on how to use DAW software

on the computer with the MOXF6/MOXF8 after connecting.

Setting up the MOXF6/MOXF8

1 If Quick Setup 1 is set to the default settings,

simultaneously hold the [QUICK SETUP] button

and press the Group [A] button.

This should be selected when recording your keyboard

performance to the DAW software on the computer. If Quick

Setup 1 is not set to the default settings, set as follows.

Audio settings

Use this setting when recording the signals from the tone

generator and the A/D INPUT [L]/[R] jacks separately to

DAW software, and playing the signals from the OUTPUT [L/

MONO]/[R] jacks directly.

MIDI settings

Use this setting when recording this instrument’s performance

(not including Arpeggio data) to the DAW software.

NOTE

For more details regarding these parameters, see the

“Reference Manual” PDF document.

Press the [STORE] button to store the settings to

internal memory.

3 Press the desired mode button for playing, and

then select the desired program for recording.

MIDI channels and MIDI ports

MIDI data is assigned to one of sixteen channels, and this

synthesizer is capable of simultaneously playing sixteen

separate Parts, via the sixteen MIDI channels. However, the

sixteen-channel limit can be overcome by using separate MIDI

“ports,” each supporting sixteen channels. While a single MIDI

cable is equipped to handle data over up to sixteen channels

simultaneously, a USB connection is capable of handling far

more—thanks to the use of MIDI ports. Each MIDI port can

handle sixteen channels, and the USB connection allows up to

eight ports, letting you use up to 128 channels (8 ports x 16

channels) on your computer. When connecting this instrument

to a computer using a USB cable, the MIDI ports are defined

as follows:

Port 1

The tone generator block in this instrument can recognize and

use only this port. When playing the MOXF6/MOXF8 as a tone

generator from the external MIDI instrument or computer, you

should set the MIDI Port to 1 on the connected MIDI device or

computer.

Port 2

This port is used to control the DAW software on the computer

from the MOXF6/MOXF8 by using the Remote Control feature.

Port 3

This port is used as the MIDI Thru Port. The MIDI data received

over Port 3 via the USB [TO HOST] terminal will be re-transmitted

to an external MIDI device via the MIDI [OUT] terminal. The

MIDI data received over Port 3 via the MIDI [IN] terminal will be

re-transmitted to an external device (computer, etc.) via the USB

[TO HOST] terminal.

Port 4

This port is used only for data communication of the MOXF6/

MOXF8 Editor. No other software or device can use this port.

Port 5

This port is used only for data communication of the MOXF6/

MOXF8 Remote Editor.

No other software or device can use this port. When using a

USB connection, make sure to match the MIDI transmit port

and the MIDI receive port as well as the MIDI transmit channel

and the MIDI receive channel. Make sure to set the MIDI port

of the external device connected to this instrument according

to the above information.

Audio channels

The audio signals of the MOXF6/MOXF8 can be output to the

USB [TO HOST] terminal and the OUTPUT [L/MONO]/[R]

jacks. When connecting to a computer, use the USB [TO

HOST] terminal. In this case, up to four audio channels (USB 1

– USB 4) are available. The output-to-channel assignments are

made in the [F5] USB I/O display of the Utility mode.

The audio signals of the MOXF6/MOXF8 can be input from the

USB [TO HOST] terminal and the A/D INPUT [L]/[R] jacks. Up

to two channels of audio can be input to the USB [TO HOST]

terminal. Set the output level by using the [DAW LEVEL] slider

on the MOXF6/MOXF8. The signals are output to the OUTPUT

[L/MONO]/[R] jack. Also, up to two audio channels can be

input

to the A/D INPUT [L]/[R] jacks. The signal is sent to the A/D

input

part of the MOXF6/MOXF8. For more details, see the

“Reference Manual” PDF document.

Recording your performance on the

MOXF6/MOXF8 to computer

Mode Direct Monitor SW

A/D In & Part Part

2StereoRec on on

Local Control off

MIDI Sync auto

Clock Out off

ARPOUTSw all off

KBDTxCh 1

TrIntSw all on

TrExtSw all on

MOXF6/MOXF8 Owner’s Manual

Quick Guide

4 In the Performance/Song/Pattern mode, set the

output channel of the Audio signal for each part.

When the output setting for the audio signal (“Mode”

parameter) is set to “2StereoRec” in Step 1, you can change

the audio output channel for each part. In the Performance

mode, this parameter can be set in the [F4] USB I/O display

of Common Edit. In the Song/Pattern mode, this parameter

can be set in the [F4] USB I/O display of Mixing Common

Edit.

NOTE

In the Voice mode, the audio output channel is fixed to USB

3/4.

Setting up the DAW software on the computer

1 Set MIDI Thru to “on” on the DAW software.

By setting MIDI Thru to “on,” the MIDI data generated by

playing the keyboard and transmitted to the computer will be

returned back to the MOXF6/MOXF8. As shown in the

example below, the MIDI data transmitted from the MOXF6/

MOXF8 then recorded to the computer via MIDI channel 1

will be returned

back from the computer to the

MOXF6/

MOXF8

via MIDI channel

3 according to the setting of the

recording Track. As a result, the tone generator of the

MOXF6/MOXF8 will sound the MIDI data generated by

playing the keyboard as MIDI data from channel 3.

The instructions below show how to use this instrument as a

MIDI tone generator. In this case, actual MIDI sequence data

is transmitted from DAW software on the computer, allowing

you to avoid using software synths and save processing

power on your computer.

Setting up the MOXF6/MOXF8

1 Press the [SONG] or [PATTERN] button to enter the

Song mode or Pattern mode.

2 Select the Song or Pattern to be edited.

3 Press the [MIXING] button to call up the Mixing

display.

4 Set up the Mixing for parts 1 – 16 as necessary.

From the Mixing display, you can select Voices and set

various parameters such as pan, volume, balance between

the Chorus/Reverb and dry sound, Insertion effect on/off and

Arpeggio on/off.

Setting up the DAW software on the computer

1 Set the MIDI output port of the Tracks for playing

the MOXF6/MOXF8 to Port 1 of the “MOXF6/

MOXF8”

2 Enter the MIDI data to each Track of the DAW

software on the computer.

The tone generator settings of the part corresponding to the

MIDI Track will be set in the Mixing mode on the MOXF6/

MOXF8.

NOTE

When using Cubase as the DAW, you can create an original

Mixing setup of the MOXF6/MOXF8 from the MOXF6/MOXF8

Editor on your computer. The created Mixing setup can be

saved as a Cubase Project file for future recall.

Remote-controlling the software

from the MOXF6/MOXF8 (Remote

mode)

The MOXF6/MOXF8 features a highly convenient Remote

mode which lets you control the DAW software and software

synthesizer on your computer via the panel operations of the

MOXF6/MOXF8. For example, you can start/stop playback of

the DAW software on the computer by using the Function

buttons and control the song position on the DAW software

by using the [DATA] dial, [INC] and [DEC] buttons instead of

using the mouse or computer keyboard.

Up to 50 Control Templates of VST Instruments can be stored

to internal memory of this instrument. With these, you can use

the MOXF6/MOXF8 to control various software synthesizers.

Use the MOXF6/MOXF8 Remote Editor for editing the Control

Template.

NOTE To use the MOXF6/MOXF8 Remote Editor, you need to install the

MOXF6/MOXF8 Remote Tools. The MOXF6/MOXF8 Remote Tools

consists of two components: MOXF6/MOXF8 Remote Editor and

MOXF6/MOXF8 Extension, which enables you to use the MOXF6/

MOXF8 along with Cubase series.

Song playback from a computer using the

MOXF6/MOXF8 as a tone generator

USB TO HOST terminal

Tone generator

block

(recognizing MIDI

Channel 3 data)

Keyboard

(output via

MIDI

Channel 1)

Local Control = off

MOXF6/MOXF8

OUT

CH3

CH1

Computer

(Cubase, etc.)

MIDI Thru = on

Remote-controlling the software synthesizer

MOXF6/MOXF8 Owner’s Manual

Quick Guide

The DAW applications Cubase, Logic Pro, SONAR and Digital

Performer can be controlled via the Remote Control mode of

the MOXF6/MOXF8.

Before you can use the Remote Control function, you’ll need

to follow the setup instructions below.

NOTE Before making the setup of DAW Remote, make sure to properly

install the Yamaha Steinberg USB Driver and the MOXF6/MOXF8

Remote Tools.

Setting up the MOXF6/MOXF8

1 Connect this instrument to the computer via a USB

cable (page 53).

2 Press the [DAW REMOTE] button to enter the

Remote mode.

3 Press the [UTILITY] button to call up the REMOTE

display of the Utility mode. Then set the “DAW

Select” to the desired DAW software.

4 Press the [STORE] button to store the settings to

internal memory.

5 Start the DAW software on the connected

computer.

Setting up the DAW software on the computer

This section explains how to set up after starting each

application.

NOTE When the cable between the MOXF6/MOXF8 and the Windows

computer is disconnected or the MOXF6/MOXF8 is turned off

accidentally, the DAW will not recognize the MOXF6/MOXF8

again even if you connect the cable again or turn the MOXF6/

MOXF8 on. If this occurs, exit the DAW software, then restart it

after setting up the MOXF6/MOXF8 and making sure the

connection is secure.

Cubase

The settings will be completed by installing MOXF6/MOXF8

Remote Tools.

SONAR

1 Pull down the [Options] menu and select [MIDI Devices]

to call up the “MIDI Devices” window.

2 Add “Yamaha MOXF6/MOXF8-2” to the Input Device,

then add “Yamaha MOXF6/MOXF8-2” to the Output

Device.

3 Pull down the [Options] menu and select [Control

Surfaces] to call up the Control Surface window.

4 Click the [+] button, select “Mackie Control,” then set the

Input Port to “Yamaha

MOXF6/MOXF8

-2” and set the

Output

Port to “Yamaha MOXF6/MOXF8-2.”

Digital Performer

1 In the Audio/MIDI setup of a Mac computer, connect Port

2 of the interface of the MOXF6/MOXF8 to Port 2 of the

tone generator. When there is only one Port for the tone

generator, add the new Port, then connect it to the

interface.

Pull down the [Setup] menu and select [ControlSurface

Setup]

to call up the Control Surface window.

3 Click the [+] button.

4 Select “Mackie Control” in the Driver section.

5 In the box for setting “Unit” and “MIDI,” select “Mackie

Control” in the “Unit” section and select “MOXF6/MOXF8

New Port 2” in the “MIDI” section.

Logic Pro

1 Select the [Preference] menu  [Control Surfaces] 

[Settings] to call up the Settings window.

2 Select the [New] menu  [Install].

3 Select “Mackie Control” in the model list, then add it as a

control surface.

MOXF6/MOXF8 Remote Tools can be downloaded from the

following Yamaha web site. For details on operating the

MOXF6/MOXF8 Remote Editor, see the PDF manual supplied

with the MOXF6/MOXF8 Remote Editor.

http://download.yamaha.com/

Remote-controlling the DAW software

For the most recent information on DAW software that can be

controlled from the MOXF6/MOXF8, see the following URL:

http://www.yamahasynth.com/

MOXF6/MOXF8 Owner’s Manual

Quick Guide

4 Set the MIDI Output Port to “Yamaha MOXF6/MOXF8

Port2.”

5 Set the MIDI Input Port to “Yamaha MOXF6/MOXF8

Port2.”

NOTE Mackie Control is the trademark of Mackie Designs, Inc.

Using the MOXF6/MOXF8 Editor

The MOXF6/MOXF8 Editor lets you edit Voice and Mixing

setups from your computer, giving you even greater editing

convenience. Furthermore, the data edited on the MOXF6/

MOXF8 is always synchronized with the data on the

computer (MOXF6/MOXF8 Editor) and vice versa. This

provides a smooth, seamless interface, making it exceptionally

easy to create and edit data.

Using the MOXF6/MOXF8 Editor

Using the MOXF6/MOXF8 Editor VST in Cubase

The MOXF6/MOXF8 Editor VST works as a VST3 plug-in

software in Cubase. In this case, you can launch the MOXF6/

MOXF8 Editor via the same operations as that of any other

VST Instrument.

Using the MOXF6/MOXF8 Editor separately

The MOXF6/MOXF8 Editor can also be used as a stand-

alone application.

Using as a Master Keyboard

The Master mode lets you:

Create and store up to 128 programs, each containing a

Voice, a Performance, a Song, or a Pattern, and each of

which can be instantly called up for use.

Assign up to four separate Zones in each Master program

for use as a master keyboard.

You can use the Master mode to memorize the settings you

use most often including the information on which mode is

used, and call up these settings instantly anytime you need

them with a single button press. Furthermore, you can

memorize the settings for controlling an external MIDI device

by the Master, allowing you to change and control the

connected external MIDI tone generator in sequence while

performing live.

Registering the Edited Voice/

Performance/Song/Pattern

The Master mode is ideal for live performance situations

since it lets you instantly switch among needed Voices,

Songs, Patterns and Performances without having to change

modes. One convenient way of using the Master mode is to

save your needed programs (Voices, Performances, etc.) to

Masters in number order, according to the songs you intend

to perform. Follow the instructions below to store programs.

1 Press the [MASTER] button to enter the Master

mode.

2 Select a Master to be edited.

The Master Play display appears.

3 Press the [F2] MEMORY button.

The MEMORY display appears.

4 At the “Mode” parameter and “Memory”

parameter, select the desired mode and program.

5 Press the [STORE] button to store the set the

Master program in the store display.

For details about the button operations and functions, see the

“Reference Manual” PDF document.

About the MOXF6/MOXF8 Editor

The MOXF6/MOXF8 Editor can be downloaded from the

following URL:

http://download.yamaha.com/

For instructions on using the MOXF6/MOXF8 Editor, refer to the

respective PDF manuals included with the software.

HINT

Integration between MOXF6/MOXF8 and Cubase

When producing music by using the MOXF6/MOXF8 together

with Cubase, the MOXF6/MOXF8 Extension contained in the

MOXF6/MOXF8 Remote Tools provides useful and convenient

functions. For example, the necessary settings for connection

will be made automatically. For more details, including the

latest information, see the following URL.

http://www.yamahasynth.com/

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Making settings for use as a master

keyboard

It is a good idea to memorize master keyboard functions to

the Master when using external multiple MIDI tone generators.

Simply by selecting a different Master, you can change the

programs in your connected external MIDI tone generators.

Here's how to do it:

1 Press the [MASTER] button to enter the Master

mode.

2 Select a Master to be edited.

3 Press the [F3] ZONE SW button.

The ZONE SW display appears.

4 Set “ZoneSwitch” to “on.”

NOTE When the “ZoneKnob” is set to “on,” the Zone Edit settings

are assigned to Knobs 1 – 8. If you want to assign the

settings in the memorized mode to Knobs 1 – 8 yourself, set

“ZoneKnob” to “off.“

5 Press the [EDIT] button, and then press the

Number [1] button.

This calls up the Master Edit displays for Zone 1.

6 Set the parameters for Zone 1 in the [F1] – [F5]

displays.

7 Use the Number [2] – [4] buttons to set the

parameters for other Zones as well as Zone 1.

8 After setting all the desired parameters, press the

[STORE] button to store your settings as a Master

program.

After completing these settings, assign a name to the Master

in the [F1] Name display of the Master Common Edit. After

naming, press the [STORE] button to store the Master.

For more information on the parameters which are edited in

the Master mode, see the “Reference Manual” PDF document.

Making Global System

Settings (Utility Mode)

In the Utility mode, you can set parameters that apply to the

entire system of this instrument. To enter the Utility mode,

press the [UTILITY] button. Pressing the [EXIT] button returns

to the original display.

This section describes some useful functions in the Utility

mode.

Setting the default mode when

turning the power on

[F1] GENERAL  [SF6] OTHER  Cursor [>] button 

“PowerOnMode”

Determines which mode is automatically called up when

turning the power on.

When this is set to “STORE+ENTER,” the display in which

you specify the mode (Voice/Performance/Master/Song/

Pattern) and the Program number will automatically be

called up when the power is turned on.

To specify a display, call it up normally, then press the

[STORE] button and the [ENTER] button simultaneously.

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Reversing the LCD status

[F1] GENERAL  [SF6] OTHER  Cursor [<] button 

“LCD Mode”

This parameter determines the LCD status.

You can use the Master mode to memorize the settings you

use most often.

Click (metronome) settings

[F2] SEQ  [SF1] CLICK

Determines the tempo, volume and output destination of the

click (metronome).

Effect settings applied to the signal

input from the A/D INPUT jack

[F3] VCE A/D

Determines the settings for the effects applied to the

incoming audio signal from the A/D INPUT [L]/[R] jacks in

the Voice mode.

Master Effect/Master EQ settings

in the Voice mode

[F2] VOICE  [SF1] MFX, [SF2] MEQ

Determines how much of the Effect and EQ processing is

applied to the master output.

Transmitting Control Change

messages using the Foot Switch

[F4] CTL ASN  [SF2] FT SW

You can transmit Control Change messages using the Foot

Switch connected to the [ASSIGNABLE] jack. For example,

when you set the value to 98 [PC Inc], the Program Change

number increases by 1 whenever the Foot Switch is pressed.

When “normal” is selected:

When “reverse” is selected:

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Saving/Loading Data (File

Mode)

The File mode provides tools for transferring data (such as

Voice, Performance, Song, and Pattern) between the

MOXF6/MOXF8 and external USB flash memory device

connected to the USB [TO DEVICE] terminal. To enter the

File mode, press the [FILE] button.

This section explains how to save/load all the data on the

user memory of this instrument as an “All” file.

Saving the settings to a USB flash

memory device

1 Connect a USB flash memory device to the USB

[TO DEVICE] terminal of this instrument.

2 Press the [FILE] button, and then press the [F2]

SAVE button.

The SAVE display appears in the File mode.

3 Set “TYPE” to “All,” and then select the desired

directory of the device. After that, press the

[ENTER] button.

If storing the root directory, keep the directory set to “root”

without pressing the [ENTER] button. If you want to make a

new directory, press the [SF3] NEW button.

4 Use the Cursor [<]/[v] buttons to move the cursor

to the file name field, assign a name to the file, and

then press the [ENTER] button.

Move to the desired location in the file name field by using

the Cursor [<]/[>] buttons, and then select the desired

characters by using the [DATA] dial or the [INC]/[DEC]

button to enter the selected character. By pressing the [SF6]

button, you can assign the name in the Character List

display. By pressing the [SF2] SET NAME button, the file/

directory name which selected in the file/directory selection

box is copied to the file name field.

Press the [SF1] EXEC button to save the file.

Loading the settings from a USB

flash memory device

1 Connect a USB flash memory device to the USB

[TO DEVICE] terminal of this instrument.

2 Press the [FILE] button, and then press the [F3]

LOAD button.

The LOAD display appears in the File mode.

3 Set “TYPE” to “All,” and then select the file

(extension: .X6A) of the memory.

Select the directory which has desired file in the file/directory

selection box, and then press the [ENTER] button. After that,

select the desired file.

Set the desired file

type for saving

The current determined directory

as the save destination of the USB

flash memory device

File/Directory Selection box

Select the desired directory of the USB

flash memory device, and then press

the [ENTER] button.

File name field

MOXF6/MOXF8 Owner’s Manual

Quick Guide

Press the [SF1] EXEC button to load the file.

NOTICE

The Load operation overwrites any data previously existing in the

specified destination internal memory. Important data should always

be saved to a USB flash memory device connected to the USB [TO

DEVICE] terminal.

Precautions when using the USB

[TO DEVICE] terminal

This instrument features a built-in USB [TO DEVICE]

terminal. When connecting a USB device to the terminal, be

sure to handle the USB device with care. Follow the

important precautions below.

NOTE For more information about the handling of USB devices, refer to

the owner’s manual of the USB device.

Compatible USB devices

Only USB memory devices of the flash-memory variety can

be used with the MOXF6/MOXF8. Furthermore, the

instrument does not necessarily support all commercially

available USB flash memory devices, nor can Yamaha

guarantee operation such USB devices that you purchase.

Before purchasing a USB flash memory device for use with

this instrument, please visit the following web page:

http://download.yamaha.com/

Connecting a USB flash memory device

When connecting a USB flash memory device to the USB

[TO DEVICE] terminal, make sure that the connector on the

memory is appropriate and that it is connected in the proper

direction.

NOTE Though the instrument supports the USB 1.1 standard, you can

connect and use a USB 2.0 storage device with the instrument.

However, note that the transfer speed is that of USB 1.1.

Formatting a USB flash memory device

When a USB flash memory device is connected, a message

may appear prompting you to format the memory. If so,

execute the Format operation (see the “Reference Manual”

PDF document).

NOTICE

The format operation overwrites any previously existing data. Make

sure that the device you are formatting does not contain important

data.

To protect your data (write-protect)

To prevent important data from being inadvertently erased,

apply the write-protect provided on the USB flash memory

device. If you are saving data to the device, make sure to

disable write-protect.

Connecting/removing the USB flash memory device

Before removing the memory from the instrument, make sure

that the instrument is not accessing data (such as in the

Save, Copy and Delete operations).

NOTICE

Avoid frequently turning the power on/off to the USB flash memory

device, or connecting/disconnecting the memory too often. Doing so

may result in the operation of the instrument “freezing” or hanging

up. While the instrument is accessing data (such as during Save,

Copy, Delete, Load and Format operations) or is mounting the USB

flash memory device (shortly after the connection), do NOT unplug

the USB connector, do NOT remove the device from the instrument,

and do NOT turn the power off to either the instrument or the USB

flash memory device. Doing so may corrupt the data on either or

both.

MOXF6/MOXF8 Owner’s Manual

Shift Function List

Some of the important functions and operations on the instrument can be executed with convenient panel control shortcuts.

Simply hold down the [SHIFT] button and press the indicated button (as described below).

Appendix

Mode Operation Function

All modes [SHIFT] + [INC]/[DEC] Increases/decreases the value by 10. (Program number in the Play mode; parameter

value in the Edit mode)

All modes [SHIFT] + [DATA] dial Increases/decreases the value by 10. (Same as [SHIFT] + [INC]/[DEC])

Voice Play [SHIFT] + BANK SELECT [DEC]/[INC] Changes the Voice Bank in the order listed below.

PRE1  USR1  PDR  UDR  GM  GMDR

All modes other than

the File mode

[SHIFT] + Knob 1 – 8 Increases/decreases the value by 10.

All modes other than

the File mode

[SHIFT] + Knob Function 1 button Sets the Knob Function to TONE 1.

All modes other than

the File mode

[SHIFT] + Knob Function 2 button Sets the Knob Function to EQ.

All modes [SHIFT] + [Level] Meter button Sets the [LEVEL] meter to the A/D INPUT level.

Voice/Performance/

Song Mixing/Pattern

Mixing/Master mode

[SHIFT] + the current mode button Executes the BULK Job of the current mode.

Voice Play/

Performance Play/

Category Search

display

[SHIFT] + [FAVORITE] Turns on/off the Favorite indicator of

the current Voice or Performance.

Voice/Performance/

Song/Pattern mode

[SHIFT] + ARP [ON/OFF] • In the Voice mode, this operation will call up the [F3] MAIN display of Arpeggio Edit.

• In the Performance/Song/Pattern mode, this operation will call up the [F1] COMMON

display of Arpeggio Edit.

Voice/Performance/

Song/Pattern mode

[SHIFT] + A/D INPUT [ON/OFF] • In the Voice mode, this operation will call up the [F3] VCE A/D – [SF1] OUTPUT display

of the Utility mode.

• In the Performance mode, this operation will call up the [F5] A/D IN – [SF1] OUTPUT

display of Common Edit.

• In the Song/Pattern mode, this operation will call up the [F5] A/D IN – [SF1] OUTPUT

display of Mixing Common Edit.

Voice/Performance/

Song/Pattern mode

[SHIFT] + EFFECT [INSERTION] Calls up the [F6] EFFECT – [SF1] CONNECT display of Common Edit.

Voice/Performance/

Song/Pattern mode

[SHIFT] + EFFECT [SYSTEM] Calls up the [F6] EFFECT – [SF1] CONNECT display of Common Edit.

Voice/Performance/

Song/Pattern mode

[SHIFT] + EFFECT [MASTER] • In the Voice mode, this operation will call up the [F2] VOICE – [SF1] MFX display of the

Utility mode.

• In the Performance mode, this operation will call up the [F2] OUT MFX – [SF2] MFX

display of Common Edit.

• In the Song/Pattern mode, this operation will call up the [F2] MFX display of Mixing

Common Edit.

Voice/Performance/

Song/Pattern mode

[SHIFT] +

ASSIGNABLE FUNCTION [1]/[2]

• In the Voice mode, this operation will call up the [F1] GENERAL – [SF4] OTHER display

of Common Edit.

• In the Performance mode, this operation will call up the [F1] GENERAL – [SF5] OTHER

display of Common Edit.

• In the Song/Pattern mode, this operation will call up the [F1] GENERAL display of

Mixing Common Edit.

Voice/Performance/

Song/Pattern mode

[SHIFT] + OCTAVE [-]/[+] Calls up the [F1] GENERAL – [SF3] KBD display of the Utility mode.

Voice/Performance/

Song/Pattern mode

[SHIFT] + TRANSPOSE [-]/[+] Calls up the [F1] GENERAL – [SF3] KBD display of the Utility mode.

Favorite indicator

MOXF6/MOXF8 Owner’s Manual

Appendix

Display Messages

LCD indication Description

All remote templates stored. Appears when you store the Control Template in the Remote mode.

Are you sure? Confirms whether you want to execute a specified operation or not.

Arpeggio memory full. The internal memory for Arpeggio data is full.

Arpeggio type copied. The Arpeggio Types are copied to the [SF1] – [SF6] buttons.

Bad USB device. The USB flash memory device connected to this instrument is unusable. Format the USB flash memory device and try

again.

Bulk protected. Bulk data cannot be received because of the setting in the Utility mode.

Can't undo. OK? When certain Song/Pattern Jobs are executed, internal memory becomes too full for use of the Undo operation.

Completed. The specified load, save, format, or other Job has been completed.

Device number is off. Bulk data cannot be transmitted/received since the device number is off.

Device number mismatch. Bulk data cannot be transmitted/received since the device numbers don’t match.

Edited data will be

discarded.

Prompts you to confirm whether or not to erase the edited data.

Edits will be stored by

Confirms whether or not you want to continue the Load operation. If you select yes, the current edits will be stored.

Edits will be stored by

saving.

Confirms whether or not you want to continue the Save operation. If you select yes, the current edits will be stored.

Empty Favorite!

[SHIFT]+[FAVORITE] to add.

Appears when you press the [FAVORITE] button with no program registered to the Favorite Category.

Executing… A format operation or Job is being executed. Please wait.

File already exists. A file having the same name as the one you are about to save already exists.

File not found. The file of the specified type cannot be found.

Folder is too deep. Directories below this level cannot be accessed.

Illegal file name. The specified file name is invalid. Try entering a different name.

Illegal file. The file specified for loading is unusable by this instrument or cannot be loaded in the current mode.

Illegal input. An invalid input or value has been specified. Check the input method or value.

Illegal measure. An invalid measure number has been specified in the Song/Pattern mode. Select the measure again.

Illegal phrase number. An invalid phrase number has been specified in the Pattern mode. Select the phrase again.

Illegal Track number. An invalid Track number has been specified in the Song/Pattern mode. Select the Track again.

Incompatible USB device A USB device which cannot be used with this instrument has been connected to the USB [TO DEVICE] terminal.

MIDI buffer full. Failed to process the MIDI data because too much data was received at one time.

MIDI checksum error. An error occurred when receiving bulk data.

MIDI data error. An error occurred when receiving MIDI data.

Mixing Voice full. The Mixing Voice cannot be stored because the number of Voices already stored has exceeded the maximum capacity.

New Flash Memory Module.

Please load waveform data.

This message appears when the Flash Memory Expansion Module (FL512M/FL1024M) which was installed in a different

MOXF has been installed to the current MOXF. If this message appears, you should save the Waveform data (including the

parameter settings) of the previous MOXF to a USB storage device, connect the USB storage device to the current MOXF,

then load the Waveform data. This occurs because the Sample without the parameter settings cannot produce the proper

sound.

No data. When a Song/Pattern Job is executed, the selected Track or range contains no data. Select an appropriate Track or range.

In addition, this message appears when a Job related to a Mixing Voice cannot be executed because the specified Mixing

Voice is not available.

No F7 (End of Exc.) Exclusive data has been entered or changed without the necessary “End of Exclusive” byte (F7). Make sure the F7

message is included.

No Flash Memory Module

installed or module is

unformatted.

This message appears when no Flash Memory Expansion Module is installed or the unformatted Module has been

installed.

No response from USB

device

There is no response from the USB device connected to the USB [TO DEVICE] terminal.

No sample data. This message appears when you try loading Waveform data with the “with sample” checkmark removed, even when the

corresponding Sample is not available on the Flash Memory Expansion Module.

Not empty folder You have attempted to delete a folder that contains data.

Not empty waveform. You have attempted to load Waveform data to a Waveform that already contains data.

MOXF6/MOXF8 Owner’s Manual

Appendix

Now Installing data to Flash

Memory Module

The Sample data is being copied to the Flash Memory Expansion Module.

Now loading... Indicates that a file is being loaded.

Now saving... Indicates that a file is being saved.

Now working... Canceling the Load/Save operation, after the [EXIT] button has been pressed.

Overwrite? A save operation will overwrite data on the USB flash memory device, and this message confirms whether it is OK to

continue or not.

Part ** is used for Drum

Assign.

This message appears when the Part switches of all Parts are set to on, and the Drum Assign function uses Part ** for the

Drum Part in Performance mode. The ** mark indicates the Part number.

Part ** is used for Layer. This message appears when the Part switches of all Parts are set to on, and the Layer function uses Part ** for the Layer

Part in the Performance mode. The ** mark indicates the Part number.

Part ** is used for Split. This message appears when the Part switches of all Parts are set to on, and the Split function uses Part ** for the Split Part

in the Performance mode. The ** mark indicates the Part number.

Phrase limit exceeded. The maximum number of Phrases (256) has been exceeded when recording, executing a Pattern Job, or editing.

Please keep power on. The data is being written to Flash ROM. Never attempt to turn off the power while data is being written to Flash ROM.

Turning the power off while this message is shown results in loss of all user data and may cause the system to freeze (due

to corruption of data in the Flash ROM). This may also result in this instrument being unable to properly start up the next

time the power is turned on.

Please reboot. Please restart this instrument.

Please stop sequencer. The operation you have attempted to execute cannot be done during Song/Pattern playback.

Power on mode stored. The settings in the Power On mode (pressing the [STORE] and [ENTER] buttons simultaneously) have been stored.

Quick Setup ** applied. Quick Setup ** has just been applied to this instrument. The ** mark indicates the Quick Setup number.

Read only file. You have attempted to delete, rename, or overwrite a read-only file.

Receiving MIDI bulk This instrument is receiving MIDI bulk data.

Sample is too long. The Sample size is too large and the load operation cannot be executed.

Sample full. The maximum overall number of Samples has been exceeded.

Sample memory full. The Sample memory is full and further Jobs or load operations cannot be executed.

Scene & Arpeggio type

stored

The Song Scene and current Arpeggio type have been stored to one of the [SF1] – [SF6] buttons.

Sequence memory full. The internal memory for Sequence data is full, preventing any further operation (such as recording, editing, Job execution,

MIDI reception/transmission, or loading from the external storage device). Try again after erasing unwanted Song, Pattern,

or User Phrase data.

Too many fixed notes When converting the Song or Pattern data to the Arpeggio data, the amount of different notes in the data to be converted

has exceeded sixteen.

Transmitting MIDI bulk This instrument is transmitting MIDI bulk data.

Unrecognized Flash

Memory Module. Please

format that.

An unformatted Flash Memory Expansion Module has been recognized. Execute the Format operation.

USB connection terminated. A break in the connection with the USB flash memory device has occurred because of an abnormal electric current.

Disconnect the device from the USB [TO DEVICE] terminal, then press the [ENTER] button.

USB device connecting Currently recognizing the USB flash memory device connected to the USB [TO DEVICE] terminal.

USB device full. The USB flash memory device is full and no more data can be saved. Use a new USB flash memory device, or make

space by erasing unwanted data from the USB flash memory device.

USB device not ready. A USB flash memory device is not properly inserted in or connected to the USB [TO DEVICE] terminal.

USB device read/write error. An error occurred while reading or writing to/from a USB flash memory device.

USB device write protected. The USB flash memory device is write protected, or you have attempted to write to read-only media.

Utility stored The settings in the Utility mode have been stored.

Waveform full. The maximum overall number of Waveforms has been exceeded.

Waveform is protected. You have attempted to load protected Waveform data.

LCD indication Description

MOXF6/MOXF8 Owner’s Manual

Appendix

Troubleshooting

No sound? Wrong sound? When a problem like this occurs, please check the following points before assuming that the product

is faulty. Many problems can be solved by executing the Factory Set operation (page 20), after backing up your data to an USB

flash memory device (page 60). If the problem persists, consult your Yamaha dealer.

No Sound.

 Is this instrument properly connected to related external equipment (e.g., amplifier, speaker, headphone) via audio cables?

Since this instrument has no built-in speakers, you will need an external audio system or a set of stereo headphones to properly

monitor it (page 17).

 Is the power of this synthesizer and any external equipment connected to it turned on?

 Have you made all the appropriate level settings—including the Master Volume on this instrument and the volume settings on any

connected external equipment?

If the Foot Controller is connected to the [FOOT CONTROLLER] jack, operate the Foot Controller and check the sound volume.

 Check the Local Control parameter in the Utility mode.

When this instrument is used by itself and this parameter is set to off, no sound is produced even if you play the keyboard.

 Check the Direct Monitor Switch parameter in the Utility mode.

When this instrument is used by itself and this parameter is set to off, no sound is produced even if you play the keyboard.

 When the Performance/Song/Pattern produces no sound, is the “ArpPlyOnly” parameter of each Part turned on?

When this parameter is turned on, the corresponding Part produces sound only via Arpeggio playback.

 Are the MIDI volume or MIDI expression settings too low when using the external controller?

 Are the effect and filter settings appropriate?

If you are using the filter, try changing the cutoff frequency. Some cutoff settings may filter out all of the sound.

 Is “Vocoder” selected as the Insertion Effect Type of the Voice?

If so, set the parameters related to the AD Part and A/D INPUT connector to the appropriate values then play the keyboard while

speaking into the connected microphone. Check whether or not the A/D INPUT [GAIN] Knob on the rear panel is set to the minimum

position.

 Are the volume or expression settings too low?

 Are the parameter settings such as Element Switch, Part Switch, Note Limit and Velocity Limit appropriate?

[UTILITY]  [F6] MIDI  [SF2] SWITCH  “LocalCtrl”

[UTILITY]  [F5] USB I/O  “DirectMonitorSw Part”

[PERFORM]  [EDIT]  Number [1] – [4]  [F1] VOICE  [SF2] MODE  “ArpPlyOnly?”

[SONG]/[PATTERN]  [MIXING]  [EDIT]  Number [1] – [16]  [F1] VOICE  [SF2] MODE  “ArpPlyOnly”

[VOICE]  [F6] EFFECT

[PERFORM]  [F6] EFFECT

[SONG]/[PATTERN]  [MIXING]  [F6] EFFECT

[VOICE]  [EDIT]  Element/Key selection  [F3] FILTER

[PERFORM]  [EDIT]  Part selection  [F4] TONE  [SF1] FILTER

[SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F4] TONE  [SF1] FILTER

[SONG]/[PATTERN]  [UTILITY]  [F2] SEQ  [SF2] FILTER

[VOICE]  [F6] EFFECT  [SF1] CONNECT  “InsEF Connect”

[UTILITY]  [F1] GENERAL  [SF1] TG  “Volume”

[VOICE]  [EDIT]  [COMMON]  [F2] OUTPUT  “Volume”

[VOICE]  [EDIT]  Element/Key selection  [F4] AMP  [SF1] LVL/PAN  “Level”

[PERFORM]  [EDIT]  [COMMON]  [F2] OUT/MFX  [SF1] OUT  “Volume”

[PERFORM]  [EDIT]  Part selection  [F2] OUTPUT  [SF1] VOL/PAN  “Volume”

[SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F2] OUTPUT  [SF1] VOL/PAN  “Volume”

[VOICE]  [EDIT]  Element/Key selection  [F1] OSC  [SF1] WAVE  “ElementSw”

[VOICE]  [EDIT]  Element/Key selection  [F1] OSC  [SF3] LIMIT

[PERFORM]  [F2] VOICE

[PERFORM]  [EDIT]  Part selection  [F1] VOICE  [SF1] VOICE  “PartSw”

[PERFORM]  [EDIT]  Part selection  [F1] VOICE  [SF3] LIMIT

MOXF6/MOXF8 Owner’s Manual

Appendix

 When playing the keyboard in the Performance/Song/Pattern mode produces no sound, has a Voice been properly assigned to each

Part?

 When Song/Pattern playback produces no sound, are the output channel of each Track in the play mode and the receive channel of

each Part in the Mixing mode set appropriately?

 When Song/Pattern playback produces no sound, is the Velocity Offset setting of the Groove appropriate?

No sound from the A/D INPUT jack

 Is the switch of the microphone turned on?

 Check the microphone type. Make sure to use a dynamic microphone.

 Is the cable between the microphone or audio equipment and this instrument properly connected?

 Is the A/D INPUT [GAIN] knob turned fully counter-clockwise (to the minimum)?

 Is the A/D INPUT [ON/OFF] button turned on?

 Check whether or not the connection status of the A/D INPUT [L]/[R] matches the “Mono/Stereo” parameter.

 Check whether or not the “Mic/Line” parameter is set to the appropriate value.

When the output level of the connected equipment (such as a microphone, guitar, bass) is low, set this parameter to “mic.” When the

output level of the connected equipment (such as a synthesizer keyboard, CD player) is high, set this parameter to “line.”

 Are the volume settings of the A/D Input Part too low?

 Are the effect settings appropriate?

 Is the output setting of the A/D Input Part set appropriately?

 Check whether or not the Vocoder Effect is selected.

When Vocoder is selected as the Insertion Effect for the current Voice or for Part 1 of the current Performance/Song/Pattern, the audio

signal input from the A/D INPUT jacks may produce no sound depending on the parameter settings.

Playback continues without stopping.

 When the ARP [ON/OFF] button is turned on, press it so that its lamp is turned off.

 When in the Song mode or Pattern mode, press the [J] (Stop) button.

 When the click sound continues, check the following parameter setting. Set this parameter to something other than “all” because this

setting always plays back the click sound regardless of the sequencer status.

Distorted sound.

 Are the effect settings appropriate?

Use of an effect at certain settings may produce distortion.

[PERFORM]  [F2] VOICE

[SONG]/[PATTERN]  [MIXING]  [F2] VOICE

[SONG]/[PATTERN]  [F3] TRACK

[SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F1] VOICE  [SF2] MODE  “ReceiveCh”

[SONG]/[PATTERN]  [F2] GROOVE  “VELO OFST”

[VOICE]  [UTILITY]  [F3] VCE A/D  “Mono/Stereo”

[PERFORM]  [EDIT]  [COMMON]  [F5] A/D IN  “Mono/Stereo”

[SONG]/[PATTERN]  [MIXING]  [EDIT]  [COMMON]  [F5] A/D IN  “Mono/Stereo”

[UTILITY]  [F1] GENERAL  [SF6] OTHER  Press [<] several times to call up the first page.  “Mic/Line”

[VOICE]  [UTILITY]  [F3] VCE A/D  [SF1] OUTPUT  “Volume”

[PERFORM]  [EDIT]  [COMMON]  [F5] A/D IN  [SF1] OUTPUT  “Volume”

[SONG]/[PATTERN]  [MIXING]  [EDIT]  [COMMON]  [F5] A/D IN  [SF1] OUTPUT  “Volume”

[VOICE]  [UTILITY]  [F3] VCE A/D

[PERFORM]  [EDIT]  [COMMON]  [F5] A/D IN

[SONG]/[PATTERN]  [MIXING]  [EDIT]  [COMMON]  [F5] A/D IN

[UTILITY]  [F4] USB I/O

[VOICE]  [F6] EFFECT  “Ins EF Connect”

[SONG]/[PATTERN]  [UTILITY]  [F2] SEQ  [SF1] CLICK  “Mode”

[VOICE]  [F6] EFFECT

[PERFORM]  [F6] EFFECT

[SONG]/[PATTERN]  [MIXING]  [F6] EFFECT

MOXF6/MOXF8 Owner’s Manual

Appendix

 Are the filter settings appropriate?

Excessively high filter resonance settings can cause distortion.

 Are any of the following volume parameters set so high that clipping is occurring?

Sound is cut off.

 Is the entire amount of notes played (via your keyboard playback and Song/Pattern/Arpeggio playback) exceeding the maximum

polyphony of this instrument?

Only one note sounds at a time.

 When this situation occurs, the Mono/Poly parameter in the current mode is set to “mono.” If you wish to play chords, set this parameter

to “poly.”

Pitch is wrong.

 Is the Master Tune parameter in the Utility mode set to a value other than “0”?

 Is the Note Shift parameter in the Utility mode set to a value other than “0”?

 When the Voice produces a wrong pitch, is the appropriate tuning system selected from Micro Tuning parameter in the Voice Edit

mode?

 When the Voice produces a wrong pitch, is the LFO Pitch Modulation Depth in the Voice Edit mode set too high?

 When the Voice produces a wrong pitch, is the Coarse Tune or the Fine Tune in the Voice Edit mode set properly?



When the Performance/Song/Pattern produces a wrong pitch, are the Note Shift and Detune parameters of each Part set to a value other

than “0”?



When the Song/Pattern playback produces a wrong pitch, is the Note Offset parameter in the Groove display set to a value other than “0”?

No effect is applied.

 Check the on/off status of the EFFECT [INSERTION]/[SYSTEM]/[MASTER] button.

 Is the Reverb Send or Chorus Send set to a value other than “0”?

[VOICE]  [EDIT]  Element/Key selection  [F3] FILTER

[PERFORM]  [EDIT]  Part selection  [F4] TONE  [SF1] FILTER

[SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F4] TONE  [SF1] FILTER

[UTILITY]  [F1] GENERAL  [SF1] TG  “Volume”

[VOICE]  [EDIT]  [COMMON]  [F2] OUTPUT  Volume

[VOICE]  [EDIT]  Element/Key selection  [F4] AMP  [SF1] LVL/PAN  “Level”

[PERFORM]  [EDIT]  [COMMON]  [F2] OUT/MFX  [SF1] OUT  “Volume”

[PERFORM]  [EDIT]  Part selection  [F2] OUTPUT  [SF1] VOL/PAN  “Volume”

[SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F2] OUTPUT  [SF1] VOL/PAN  “Volume”

[VOICE]  [F4] PORTA  “Mono/Poly”

[PERFORM]  [EDIT]  Part selection  [F1] VOICE  [SF2] MODE  “Mono/Poly”

[SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F1] VOICE  [SF2] MODE  “Mono/Poly”

[UTILITY]  [F1] GENERAL  [SF1] TG  “Tune”

[UTILITY]  [F1] GENERAL  [SF1] TG  “NoteShift”

[VOICE]  [EDIT]  [COMMON]  [F1] GENERAL  [SF2] PLY MODE  “M. Tuning No.”

[VOICE]  [EDIT]  Element/Key selection  [F5] LFO  “PMod”

[VOICE]  [EDIT]  Element/Key selection  [F2] PITCH  “Coarse” / “Fine”

[PERFORM]  [EDIT]  Part selection  [F4] TONE  [SF1] TUNE

[SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F4] TONE  [SF1] TUNE

[SONG]/[PATTERN]  [F2] GROOVE  “NOTE OFST”

[VOICE]  [EDIT]  [COMMON]  [F2] OUTPUT  “ChoSend” / “RevSend”

[PERFORM]  [EDIT]  [COMMON]  [F2] OUT/MFX  [SF1] OUT  “ChoSend” / “RevSend”

[SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F2] OUTPUT  [SF1] VOL/PAN  “ChoSend” / “RevSend”

MOXF6/MOXF8 Owner’s Manual

Appendix

 Have any or all of the Elements’ Insertion Effect Output parameters been set to “thru” in the effect setting display in the Voice Edit

mode?

 Have any or all of the effect types been set to “thru” or “No Effect”?

 When this occurs in the Performance mode/Song mode/Pattern mode, check whether the Insertion Switch (INS SW) parameters are

set properly or not.

The Edit Indicator appears, even when parameters are not being edited.



Keep in mind that even though the Edit mode is not active, simply moving a Knob/Slider or playing back the Song/Pattern changes the

current Voice, Performance, or Mixing, causing the Edit Indicator to appear.

Cannot start the Arpeggio.

 Check whether the ARP [ON/OFF] button is turned on or off.

 When a User Arpeggio type is selected, does the currently selected Arpeggio actually contain data?

 Are the Arpeggio related parameters such as Note Limit and Velocity Limit set appropriately?

 When this situation occurs in the Performance/Song/Pattern mode, check the Arpeggio Switch parameter.

If this parameter for the current Part is set to off, Arpeggio playback will not be triggered by your keyboard performance even if the

ARP [ON/OFF] button is turned on.

 Is the MIDI Sync parameter set to “internal” or “auto” (using internal clock)?

Cannot stop the Arpeggio.

 When Arpeggio playback does not stop even if you release the key, set the Arpeggio Hold parameter to “off.”

The Voice assigned to the Performance produces a different sound from the one in the Voice mode.

 This is normal because the Voice sound is determined by the parameter settings in the Performance mode.

To solve this problem, you will need to apply the same parameter settings as those used in the Voice mode via the following three

steps.

1. Set the “P.WithVce” (Parameter With Voice) parameter to “on” for a certain Part then reselect the same Voice. The settings of some

Voice Common parameters will be applied to the Performance Part.

2. Execute the Voice Copy Job in the Performance Job mode.

This Job copies the System Effect, Master Effect and Master EQ settings in the Voice mode to the Performance Common

parameters.

3. Set the Reverb Send Level and Chorus Send Level to the desired value (same as in the Voice mode) manually.

The Song/Pattern cannot be started even when pressing the [F] (Play) button.

 Does the selected Song or Pattern (phrase) actually contain data?

 Is the [DAW REMOTE] button turned on?

 Is the MIDI Sync parameter set to “internal” or “auto” (using internal clock)?

[VOICE]  [F6] EFFECT  [SF1] CONNECT  “EL: OUT 1-8”

[PERFORM]  [F6] EFFECT  [SF2] INS SW

[SONG]/[PATTERN]  [MIXING]  [F3] EFFECT  [SF2] INS SW

[VOICE]  ARP [EDIT]  [F4] LIMIT

[PERFORM]  ARP [EDIT]  [F4] LIMIT

[SONG]/[PATTERN]  ARP [EDIT]  [F4] LIMIT

[PERFORM]  ARP [EDIT]  [F3] MAIN  Part selection  “Switch”

[SONG]/[PATTERN]  ARP [EDIT]  [F3] MAIN  Part selection  “Switch”

[UTILITY]  [F5] MIDI  [SF3] SYNC  “MIDI Sync” = “auto” or “internal”

[VOICE]  ARP [EDIT]  [F3] MAIN  “Hold”

[PERFORM]  ARP [EDIT]  [F3] MAIN  Part selection  “Hold”

[SONG]/[PATTERN]  ARP [EDIT]  [F3] MAIN  Part selection  “Hold”

[PERFORM]  [EDIT]  Number [1] – [4]  [F1] VOICE  [SF1] VOICE  “P.WithVce”

[PERFORM]  [JOB]  [F3] COPY  [SF2] VOICE

[PERFORM]  [EDIT]  Part selection  [F2] OUTPUT  [SF2] EF SEND

[UTILITY]  [F5] MIDI  [SF3] SYNC  “MIDI Sync” = “auto” or “internal”

MOXF6/MOXF8 Owner’s Manual

Appendix

Song/Pattern (Phrase) cannot be recorded.

 Is there enough free memory for recording?

The total memory capacity determines the number of Songs/Patterns (phrases) that can be recorded. For example, if the memory

contains Songs/Patterns (phrases) that use up a large amount of memory, the memory may become full even though the available

Pattern or Song numbers are not all used.

Cannot enter the Pattern Job mode/Pattern Mixing mode even when pressing the [JOB] button in the

Pattern mode.

 Check whether the instrument is in the Pattern Chain mode or not.

If so, exit from the Pattern Chain mode, then press the [JOB] button or [MIXING] button.

The drum sound is wrong or unexpected when changing the transpose value in the Song/Pattern Play

mode.

 This is normal. Changing the transpose setting while playing a Drum Voice will produce different sounds for the same keys played.

Data communication between the computer and this instrument does not work properly.

 Check whether the Port settings on the computer are appropriate or not.

 Check whether or not the MIDI IN/OUT parameter is set to the appropriate value.

 This problem may be solved by reducing the computer load. To do this, set the USB Audio Output Channel to “2ch” in the following

display. If the setting is changed in the display, press the [ENTER] button and then restart the instrument.

The sound is not produced properly even when playing back the Song data on the computer or the MIDI

instrument connected to this instrument.

 Make sure to set this instrument to the Song mode or Pattern mode.

The Voice mode or Performance mode may not produce the proper sound even when playing back Song data on the MIDI

instrument or the computer connected to this instrument.

MIDI bulk data transmission/reception does not work properly.

 Is the Receive Bulk parameter set to on?

 When receiving MIDI bulk data transmitted via the Bulk Dump function and recorded to the external MIDI device, you need to set the

MIDI Device Number to the same value as when transmitting.

 When transmission does not work properly, is the device number of the MIDI instrument connected to this instrument set to match the

Device Number Parameter in the Utility mode?

Cannot save data to the external USB flash memory device

 Is the USB flash memory device being used write protected? (Write-protect should be set to off for saving data.)

 Is the USB flash memory device being used properly formatted?

Cannot enter the Edit mode

 Is Category Search turned on?

Turn off Category Search then press the [EDIT] button.

[UTILITY]  [F6] MIDI  [SF4] OTHER  “MIDI IN/OUT”

[UTILITY]  [F5] USB I/O  [SF1] OUT CH

[UTILITY]  [F6] MIDI  [SF2] SWITCH  “RcvBulk”

[UTILITY]  [F5] MIDI  [SF1] CH  “DeviceNo”

[FILE]  [F1] CONFIG  [SF2] FORMAT

MOXF6/MOXF8 Owner’s Manual

Appendix

Installing Optional

Hardware

Available devices

The following optional devices can be installed to the MOXF.

Installation locations

Installation Precautions

Before installing the optional hardware, make sure you have

a Phillips screwdriver and ample space to work.

WARNING

• Before beginning installation, switch off the power to the

instrument and connected peripherals, and unplug them from the

power outlet. Installation or removal of any devices should be

started ONLY after the instrument (and any optional hardware)

returns to normal room temperature. Then remove all cables

connecting the instrument to other devices. (Leaving the power

cord connected while working can result in electric shock. Leaving

other cables connected can interfere with work.)

• Be careful not to drop any screws inside the instrument during

installation. (This can be prevented by keeping the optional units

and cover away from the instrument while attaching). If this does

happen, be sure to remove the screw(s) from inside the unit before

turning the power on. Loose screws inside the instrument can

cause improper operation or serious damage. If you are unable to

retrieve a dropped screw, consult your Yamaha dealer for advice.

• Install the optional units carefully as described in the procedure

below. Improper installation can cause shorts which may result in

irreparable damage and pose a fire hazard.

• Do not disassemble, modify, or apply excessive force to board

areas and connectors on optional units. Bending or tampering with

boards and connectors may lead to electric shock, fire, or

equipment failures.

CAUTION

• It is recommended that you wear gloves to protect your hands from

metallic projections on optional units and other components.

Touching leads or connectors with bare hands may cause finger

cuts, and may also result in poor electrical contact or electrostatic

damage.

• Be careful of static electricity. Static electricity discharge can

damage the IC chips. Before you handle the optional units, to

reduce the possibility of static electricity, touch unpainted metal

parts or a ground wire on a device that is grounded.

• Handle the optical units with care. Dropping or subjecting them to

any kind of shock may cause damage or result in a malfunction.

• Do not touch the exposed metal parts in the circuit board. Touching

these parts may result in a faulty contact.

• Be careful not to misplace any of the screws.

• Do not use any screws other than what are installed on the

instrument. Use of incorrect screws can cause damage.

FL512M/FL1024M

(Flash memory expansion module)

Bottom cover for the FL512M/FL1024M

MOXF6

MOXF8

MOXF6/MOXF8 Owner’s Manual

Appendix

Installing Optional Hardware

FL512M/FL1024M

Configuration

There are two types of the Flash Memory Expansion Module:

 FL512M

Features a memory size of 512 MB.

 FL1024M

Features a memory size of 1024 MB.

Installation Procedure

1 Turn the power of the MOXF off, and disconnect

the AC power cord. Also, make sure to disconnect

the MOXF from any connected external devices.

2 Turn the MOXF upside down so that the keyboard

faces down and you have direct access to the

underside of the instrument.

To protect the Knobs, Wheels and Sliders from damage,

place the keyboard so the four corners are supported by

something that provides sufficient support like magazines or

cushions. Place supports at all four corners, taking care not

to touch the Knobs, Wheels and Sliders.

CAUTION

• Since the instrument—particularly the MOXF8—is very heavy, this

procedure should not be done alone, but by two or three people.

3 Remove the cover from the bottom.

With the rear panel of the MOXF facing you, remove the

screws from the cover by using the Phillips screwdriver. After

removing the screws, slide the cover away to remove it.

Important

Keep the removed screws in a safe place. They will be used when re-

attaching the cover to the instrument after installation.

4 Attach the FL1024M or FL512M to the slot.

As shown below.

Attach the module to the slot via the following steps.

4-1 Insert the Module vertically in the slot and align the

screws (on the Module) to the female screws

respectively.

 Rear side

View of the keyboard from the bottom

Place supports at all four corners, taking care

not to touch the Knobs, Wheels and Sliders.

 Rear side

Bottom

Location for

FL512M/

FL1024M

Slot

Female

screws

Slot

Female screws

 Rear side

FL512M/

FL1024M

MOXF6/MOXF8 Owner’s Manual

Appendix

4-2 Press the top of the connector as shown, then push the

connector firmly into the slot.

4-3 Tighten each screw of the Memory Module to each

female screw of the MOXF with your hand as shown

below.

5 Re-install the cover you removed in step 3, in

reverse order.

6 Check that the installed Module or Modules are

functioning properly.

6-1 Turn the MOXF right side up again so that the keyboard

faces up then turn the power on. While launching, you

will see a message indicating that the Flash Memory

Module cannot be recognized.

6-2 Press the [FILE] button to enter the File mode then

press the [F6] FLASH button.

6-3 Press the [SF1] Format button.

6-4 Press the [ENTER] button to execute the Format

operation.

6-5 Check whether the Total size shown on the display is

correct or not.

Removing the Module

1 Loosen both the screws.

NOTICE

• If you cannot loosen the screw with your hand, use a Phillips

screwdriver. In this case, be careful NOT to scratch the circuit

board of the FL512M/FL1024M and MOXF.

• Since the screws can be removed from the module, be careful NOT

to drop them inside the instrument when loosening them.

2 Pull out the FL512M/FL1024M vertically.

3 Attach the cover to the bottom panel.

Position the cover on the bottom panel aligning the screws

with the screw holes, then tighten the screws with a Phillips

screwdriver to fix the cover.

Press this section

lightly but firmly

Serial No. seal

 Rear side

Bottom

MOXF6/MOXF8 Owner’s Manual

Appendix

Specifications

Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or

specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your

Yamaha dealer.

Keyboards

MOXF8 88 keys, GHS keyboard (Initial Touch)

MOXF6 61 keys, semi-weighted keyboard (Initial Touch)

Tone Generator

block

Tone Generator AWM2, with Expanded Articulation

Polyphony 128 notes

Multi-timbral Capacity 16 parts (Internal), A/D input part

Wave 741MB (when converted to 16-bit linear format), 3,977 waveforms

Voice Preset: 1,152 Normal Voices + 72 Drum Kits

GM: 128 Normal Voices + 1 Drum Kit

User: 384 Normal Voices + 32 Drum Kits

Performance User: 256 (up to 4 parts)

Filter 18 types

Effect System Reverb x 9 types, Chorus x 22 types, Insertion (A, B) x 54 types x 8 parts, Vocoder x 1 (uses

both Insertion Effect A and B blocks), Master Effect x 9 types, Master EQ (5 bands), Part EQ

(3 bands, stereo)

Sequencer

block

Note Capacity Approx. 226,000 notes

Note Resolution 480 ppq (parts per quarter note)

Maximum Polyphony 124 notes

Tempo (BPM) 5 – 300

Recording type Real time replace, Real time overdub (with the exception of the Pattern Chain), Real time

punch in/out (Song only), Step (with the exception of the Pattern Chain)

Tracks Song: 16 sequence Tracks (Loop on/off can be set for each Track), Tempo Track, Scene Track

Pattern: 16 Phrase Tracks

Pattern Chain: Pattern Track, Tempo Track, Scene Track

Songs 64 Songs

Mixing Voices: 16 Voices per Song/Pattern (up to 256 Voices)

Mixing Templates: 32 for all Songs and Patterns

Scene Memory 6 per Song

Patterns 64 Patterns (x 16 sections)

Measures: 256 maximum

Phrases User Phrases: 256 per Pattern

Arpeggio Preset: 7,981 types

User: 256 types

(MIDI Sync, MIDI transmit/receive channel, Velocity Limit, and Note Limit can be set. 4 Arpeggio parts can be played

simultaneously.)

Sequence Format Original format, SMF format 0, 1 (Format 1 load only)

Others

Master User:128

(Each master includes Master keyboard settings with 4 Zones, Assignable Knob settings, Program Change table.)

Sequence Software

compatible with the

Remote Control function

For Windows

: Cubase 7 series, SONAR X2

For Mac

: Cubase 7 series, Logic Pro 9, Digital Performer 7

(Functions to be controlled differ depending on the software.)

Controllers Pitch Bend wheel, Modulation wheel, Assignable Knob x 8, [DATA] dial x 1, Assignable

Function buttons x 2

Display 240 x 64 dot, backlit LCD

Connectors OUTPUT [L/MONO]/[R] (standard phone jack), A/D INPUT [L]/[R] (standard phone jack),

[PHONES] (standard stereo phone jack), [FOOT CONTROLLER], FOOT SWITCH

[ASSIGNABLE]/[SUSTAIN], MIDI [IN]/[OUT]/[THRU], USB [TO HOST]/[TO DEVICE], DC IN

Power Consumption 13W

Dimensions, Weight MOXF8: 1320 (W) x 405 (D) x 168 (H) mm, 14.9 kg

MOXF6: 1030 (W) x 358 (D) x 125 (H) mm, 7.1 kg

Accessories AC adaptor (PA-150 or an equivalent recommended by Yamaha), USB cable, Owner’s Manual

(this book), Online Manual CD-ROM x 1 (containing Reference Manual, Synthesizer

Parameter Manual, and Data List), CUBASE AI DOWNLOAD INFORMATION

Optional Memory Module FL512M/FL1024M x 1

MOXF6/MOXF8 Owner’s Manual

Appendix

Index

A/D INPUT [GAIN] knob ......................................................... 12

A/D INPUT [L] and [R] jacks ............................................. 16, 38

A/D INPUT [ON/OFF] button ................................................... 12

ARP [EDIT] button ............................................................. 13, 31

ARP [ON/OFF] button ....................................................... 13, 27

Arpeggio ........................................................................... 27, 34

ASSIGNABLE FUNCTION [1]/[2] buttons ............................... 12

Audio channels ....................................................................... 54

audio equipment ..................................................................... 38

BANK SELECT [DEC]/[INC] buttons ....................................... 14

[CATEGORY SEARCH] button .......................................... 14, 26

CHAR ...................................................................................... 22

Click ........................................................................................ 59

[COMMON] button .................................................................. 14

Common Edit .......................................................................... 29

Compare function ................................................................... 29

Connect (Computer) ............................................................... 53

Connect (External MIDI Instrument) ....................................... 51

Cubase ....................................................................... 56, 57, 73

Cursor buttons .................................................................. 14, 21

[DATA] dial ....................................................................... 14, 21

[DAW LEVEL] slider ................................................................ 12

[DAW REMOTE] button ..................................................... 13, 55

DAW software ......................................................................... 54

DC IN connector ..................................................................... 16

[DEC] button ..................................................................... 14, 21

Demo Pattern .......................................................................... 47

Demo Song ............................................................................. 19

Digital Performer ............................................................... 56, 73

Display Messages .................................................................. 63

Drum Assign ........................................................................... 33

[DRUM ASSIGN] button .......................................................... 14

Drum Voice ............................................................................. 25

Edit Indicator ........................................................................... 28

Effect ................................................................................. 29, 59

EFFECT buttons ...................................................................... 13

Element Edit ............................................................................ 29

[ENTER] button ....................................................................... 14

[EXIT] button ........................................................................... 14

[F1] – [F6] (Function) buttons ........................................... 13, 21

Factory Settings ...................................................................... 20

[FAVORITE] button ........................................................... 14, 26

Favorite Category ................................................................... 26

File Mode ................................................................................ 60

FL512M/FL1024M ....................................................................70

Flash Memory Expansion Module ...........................................70

[FOOT CONTROLLER] jack ....................................................16

FOOT SWITCH [ASSIGNABLE]/[SUSTAIN] jacks ...................16

Format .....................................................................................61

GM Bank ..................................................................................25

GM Voice .................................................................................25

Group [A] – [H] buttons ...........................................................14

Headphones ............................................................................17

[INC] button .......................................................................14, 21

Key Edit ...................................................................................29

Keyboard .................................................................................12

Knob Function button ........................................................12, 28

KNOB FUNCTION pop-up window .........................................28

Knobs ................................................................................12, 28

Layer .......................................................................................31

[LAYER] button ........................................................................14

LCD .........................................................................................13

LCD status ...............................................................................59

[LEVEL] meter .........................................................................12

[LEVEL] meter button ..............................................................12

Load ........................................................................................60

Logic Pro ...........................................................................56, 73

Master Effect ...........................................................................59

Master EQ ................................................................................59

Master mode ...........................................................................57

MASTER VOLUME .............................................................12, 18

microphone .............................................................................38

MIDI [IN] / [OUT] / [THRU] terminals .......................................16

MIDI channels .........................................................................54

MIDI ports ................................................................................54

MIDI Receive Channel .............................................................52

MIDI Transmit Channel ............................................................52

Mixing ................................................................................40, 45

Mixing template .......................................................................46

[MODE] buttons .......................................................................14

Modes ......................................................................................23

Modulation wheel ....................................................................12

MOXF6/MOXF8 Editor .............................................................57

Mute ..................................................................................34, 41

[MUTE] button .........................................................................15

MOXF6/MOXF8 Owner’s Manual

Appendix

Naming ................................................................................... 22

Normal Voice .......................................................................... 25

NUM ........................................................................................ 21

Number [1] – [16] buttons ...................................................... 15

OCTAVE [-] and [+] buttons ............................................. 12, 27

OUTPUT [L/MONO] and [R] jacks .......................................... 16

Part .......................................................................................... 34

Pattern ..................................................................................... 36

Pattern Chain .......................................................................... 49

Pattern mode .......................................................................... 47

Pattern Patch display .............................................................. 49

Pattern Play ............................................................................. 47

[PATTERN SECTION/PERFORMANCE CONTROL] button .... 15

Performance Creator ........................................................ 14, 31

Performance Edit .................................................................... 35

Performance Mode ................................................................. 34

Performance Play .................................................................... 34

[PHONES] (Headphone) jack ................................................. 16

Pitch Bend wheel .................................................................... 12

Power On Mode ...................................................................... 58

Power supply .......................................................................... 17

Preset Banks ........................................................................... 25

Punch In/Out ........................................................................... 43

Quick Setup ............................................................................ 54

Realtime Recording .......................................................... 40, 43

Record (Pattern) ..................................................................... 47

Record (Performance) ............................................................ 36

Record (Song) ........................................................................ 41

Remote Control ....................................................................... 55

Save ........................................................................................ 60

Section .................................................................................... 38

Section Length ........................................................................ 38

SEQ TRANSPORT button .................................................. 13, 19

[SF1] – [SF6] (Sub Function) buttons ............................... 13, 21

[SHIFT] button ......................................................................... 14

Shift Function List .................................................................... 62

Solo ................................................................................... 34, 41

[SOLO] button ......................................................................... 15

SONAR .............................................................................. 56, 73

Song ........................................................................................ 36

Song mode ............................................................................. 40

Speaker ................................................................................... 17

Split ......................................................................................... 32

[SPLIT] button ......................................................................... 14

Standby/On switch .................................................................. 16

Step Recording ................................................................. 40, 41

Store .................................................................................. 29, 46

Track .......................................................................................40

[TRACK] button .......................................................................15

TRANSPOSE [-] and [+] buttons .......................................13, 27

Troubleshooting .......................................................................65

USB [TO DEVICE] terminal ......................................................61

USB [TO HOST] terminal .........................................................53

USB flash memory device .................................................60, 61

USB terminals ..........................................................................16

User Banks ..............................................................................25

User Phrase .......................................................................48, 49

Utility mode ..............................................................................58

Vocoder ...................................................................................39

Voice Edit ................................................................................28

Voice mode .............................................................................25

Voice Play ................................................................................25

Yamaha Steinberg USB Driver ................................................53

MOXF6/MOXF8 Owner’s Manual

Memo

MOXF6/MOXF8 Owner’s Manual

Memo

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha

ou au distributeur le plus proche de vous figurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más

cercana o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Toronto, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México, S.A. de C.V.

Av. Insurgentes Sur 1647 “Prisma Insurgentes”,

Col. San Jose Insurgentes, Del. Benito Juarez,

03900, Mexico, D.F.

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi,

CEP 04534-013 São Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.,

Sucursal Argentina

Olga Cossettini 1553, Piso 4 Norte,

Madero Este-C1107CEK

Buenos Aires, Argentina

Tel: 54-11-4119-7000

VENEZUELA

Yamaha Music Latin America, S.A.,

Sucursal Venezuela

C.C. Manzanares Plaza P4

Ofic. 0401- Manzanares-Baruta

Caracas Venezuela

Tel: 58-212-943-1877

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso No.7, Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, República de Panamá

Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND

Yamaha Music Europe GmbH (UK)

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, U.K.

Tel: 01908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH

Branch Switzerland in Zürich

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 044-387-8080

AUSTRIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/HUNGARY/

ROMANIA/SLOVAKIA/SLOVENIA

Yamaha Music Europe GmbH

Branch Austria (Central Eastern Europe Office)

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

POLAND/LITHUANIA/LATVIA/ESTONIA

Yamaha Music Europe GmbH

Branch Poland Office

ul. Wrotkowa 14 02-553 Warsaw, Poland

Tel: 022-500-2925

BULGARIA

Dinacord Bulgaria LTD.

Bul.Iskarsko Schose 7 Targowski Zentar Ewropa

1528 Sofia, Bulgaria

Tel: 02-978-20-25

MALTA

Olimpus Music Ltd.

The Emporium, Level 3, St. Louis Street Msida

MSD06

Tel: 02133-2144

NETHERLANDS/BELGIUM/

LUXEMBOURG

Yamaha Music Europe Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Music Europe

7 rue Ambroise Croizat, Zone d'activites Pariest,

77183 Croissy-Beaubourg, France

Tel: 01-64-61-4000

ITALY

Yamaha Music Europe GmbH, Branch Italy

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha Music Europe GmbH Ibérica, Sucursal

en España

Ctra. de la Coruna km. 17,200, 28231

Las Rozas (Madrid), Spain

Tel: +34-91-639-88-88

GREECE

Philippos Nakas S.A. The Music House

147 Skiathou Street, 112-55 Athens, Greece

Tel: 01-228 2160

SWEDEN

Yamaha Music Europe GmbH Germany filial

Scandinavia

J. A. Wettergrensgata 1, Box 30053

S-400 43 Göteborg, Sweden

Tel: +46 31 89 34 00

DENMARK

Yamaha Music Europe GmbH, Tyskland – filial

Denmark

Generatorvej 6A, DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

F-Musiikki Oy

Kluuvikatu 6, P.O. Box 260,

SF-00101 Helsinki, Finland

Tel: 09 618511

NORWAY

Yamaha Music Europe GmbH Germany -

Norwegian Branch

Grini Næringspark 1, N-1361 Østerås, Norway

Tel: 67 16 78 00

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120, IS-128 Reykjavik,

Iceland

Tel: 525 5000

RUSSIA

Yamaha Music (Russia) LLC.

Room 37, bld. 7, Kievskaya street, Moscow,

121059, Russia

Tel: 495 626 5005

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

SOUTH AFRICA

Global Music Instruments

Unit 4, 130 Boeing Road East Bedfordview 2008

Postnet Suite 130, Private Bag X10020 Edenvale

1610, South Africa

Tel: 27-11-454-1131

OTHER AFRICAN COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jebel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

TURKEY/CYPRUS

Yamaha Music Europe GmbH

Merkezi Almanya Türkiye İstanbul Şubesi

Maslak Meydan Sokak No:5 Spring Giz Plaza

Bağımsız Böl. No:3, 34398 Şişli, İstanbul

Tel: +90-212-999-8010

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jebel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: 021-6247-2211

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 2737-7688

INDIA

Yamaha Music India Pvt. Ltd.

Spazedge building, Ground Floor, Tower A,

Sector 47, Gurgaon- Sohna Road, Gurgaon, Haryana,

India

Tel: 0124-485-3300

INDONESIA

PT. Yamaha Musik Indonesia (Distributor)

Yamaha Music Center Bldg. Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 021-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,

Kangnam-Gu, Seoul, Korea

Tel: 02-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn., Bhd.

No.8, Jalan Perbandaran, Kelana Jaya, 47301

Petaling Jaya, Selangor, Malaysia

Tel: 03-78030900

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music (Asia) Private Limited

Block 202 Hougang Street 21, #02-00,

Singapore 530202, Singapore

Tel: 65-6747-4374

TAIWAN

Yamaha Music & Electronics Taiwan Co.,Ltd.

3F, No.6, Section 2 Nan-Jing East Road, Taipei,

Taiwan R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

3, 4, 15 and 16th floor, Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: 02-215-2622

VIETNAM

Yamaha Music Vietnam Company Limited

15th Floor, Nam A Bank Tower, 201-203 Cach

Mang Thang Tam St., Ward 4, Dist.3,

Ho Chi Minh City, Vietnam

Tel: +84-8-3818-1122

OTHER ASIAN COUNTRIES

Yamaha Corporation

Market Development Section

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2312

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

NEW ZEALAND

Music Works LTD

P.O.BOX 6246 Wellesley, Auckland 4680,

New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation

Market Development Section

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2312

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

DMI7

C.S.G., Digital Musical Instruments Division

305MWTY*.*-**A0

Printed in China

ZG45700

Yamaha Web Site (English)

http://www.yamahasynth.com/

Yamaha Downloads

http://download.yamaha.com/

ZG45700

Documenttranscriptie

Owner’s Manual EN SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind. The use of an extension cord is not recommended! If you must use an extension cord, the minimum wire size for a 25’ cord (or less) is 18 AWG. NOTE: The smaller the AWG number, the larger the current handling capacity. For longer extension cords, consult a local electrician. This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please observe all safety markings and instructions that accompany the accessory product. SPECIFICATIONS SUBJECT TO CHANGE: The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units. This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for long periods of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. IMPORTANT: The louder the sound, the shorter the time period before damage occurs. Some Yamaha products may have benches and / or accessory mounting fixtures that are either supplied with the product or as optional accessories. Some of these items are designed to be dealer assembled or installed. Please make sure that benches are stable and any optional fixtures (where applicable) are well secured BEFORE using. Benches supplied by Yamaha are designed for seating only. No other uses are recommended. NOTICE: Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service. ENVIRONMENTAL ISSUES: Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. This product may also use “household” type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that the charger is intended for the battery being charged. When installing batteries, never mix old batteries with new ones, and never mix different types of batteries. Batteries MUST be installed correctly. Mismatches or incorrect installation may result in overheating and battery case rupture. Warning: Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by the laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information. Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly. NAME PLATE LOCATION: The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate. You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase. Model Serial No. Purchase Date Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following: 92-BP (bottom) PLEASE KEEP THIS MANUAL This product contains a high intensity lamp that contains a small amount of mercury. Disposal of this material may be regulated due to environmental considerations. For disposal information in the United States, refer to the Electronic Industries Alliance web site: www.eiae.org * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. 2 MOXF6/MOXF8 Owner’s Manual (mercury) FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Yamaha Corporation of America Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620 Telephone : 714-522-9011 Type of Equipment : MUSIC PRODUCTION SYNTHESIZER Model Name : MOXF6, MOXF8 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (FCC DoC) (class B) The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the bottom of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. (bottom_en_01) OBSERVERA! Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den ar ansluten till vägguttaget, även om själva apparaten har stängts av. ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt, sålænge netledningen sidder i en stikkontakt, som er tændt — også selvom der er slukket på apparatets afbryder. VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta. (standby) Information for Users on Collection and Disposal of Old Equipment This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC. By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [For business users in the European Union] If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. (weee_eu_en_01) MOXF6/MOXF8 Owner’s Manual 3 PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe and handy place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the instrument, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument inspected by qualified Yamaha service personnel. Power supply/AC power adaptor • Do not place the power cord near heat sources such as heaters or radiators. Also, do not excessively bend or otherwise damage the cord, or place heavy objects on it. • Never insert or remove an electric plug with wet hands. • Only use the voltage specified as correct for the instrument. The required voltage is printed on the name plate of the instrument. • Use the specified adaptor (page 73) only. Using the wrong adaptor can result in damage to the instrument or overheating. • Check the electric plug periodically and remove any dirt or dust which may have accumulated on it. Fire warning • Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire. If you notice any abnormality Do not open • This instrument contains no user-serviceable parts. Do not open the instrument or attempt to disassemble or modify the internal components in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. Water warning • When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. (If you are using batteries, remove all batteries from the instrument.) Then have the device inspected by Yamaha service personnel. - The power cord or plug becomes frayed or damaged. - It emits unusual smells or smoke. - Some object has been dropped into the instrument. - There is a sudden loss of sound during use of the instrument. • Do not expose the instrument to rain, use it near water or in damp or wet conditions, place on it any containers (such as vases, bottles or CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following: Power supply/AC power adaptor • Do not connect the instrument to an electrical outlet using a multiple-connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet. • When removing the electric plug from the instrument or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. • Remove the electric plug from the outlet when the instrument is not to be used for extended periods of time, or during electrical storms. Location • Do not place the instrument in an unstable position where it might accidentally fall over. • Before moving the instrument, remove all connected cables, to prevent damage to the cables or injury to anyone who might trip over them. DMI-5 4 MOXF6/MOXF8 Owner’s Manual • When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. Connections • Before connecting the instrument to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum. • Be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level. 1/2 Handling caution Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed. • Never insert or drop paper, metallic, or other objects into the gaps on the panel or keyboard. This could cause physical injury to you or others, damage to the instrument or other property, or operational failure. Always turn the power off when the instrument is not in use. • Do not rest your weight on, or place heavy objects on the instrument, and do not use excessive force on the buttons, switches or connectors. Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum level. • Do not use the instrument/device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet. DMI-5 Make sure to discard used batteries according to local regulations. 2/2 NOTICE To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.  Handling and Maintenance • Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise. • Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation. • Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard. • When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.  Saving data • The data in the instrument’s Edit Buffer (memory location for edited data) will be lost when it is turned off. Save your important data to the user memory, a USB flash memory device or external device such as a computer. Keep in mind that saved data may be lost due to malfunction or incorrect operation. • To protect against data loss due to media damage, we recommend that you save your important data onto two USB flash memory devices/external media. Information  About copyrights • Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use. • This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.  About functions/data bundled with the instrument • This device is capable of using various types/formats of music data by optimizing them to the proper format music data for use with the device in advance. As a result, this device may not play them back precisely as their producers or composers originally intended.  About this manual • The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your instrument. • Windows is a registered trademark of Microsoft® Corporation in the United States and other countries. • Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. About the latest Firmware Version Yamaha may from time to time update firmware of the product and the other associated software without notice for improvement. We recommend that you check our web site for the latest releases and upgrade your firmware of the MOXF6/MOXF8 or the associated software. http://download.yamaha.com/ Note that the explanations in this Owner’s Manual apply to the version of firmware when this Owner’s Manual was produced. For details about additional functions included in later releases, refer to the above website. MOXF6/MOXF8 Owner’s Manual 5 A message from the MOXF6/MOXF8 Development Team Thank you for purchasing the Yamaha MOXF6/MOXF8 Music Production Synthesizer. We, as the development team, have designed this instrument so that players of every genre and level can easily enjoy truly high-quality sounds and advanced functions in creating and performing music. SOUND Extraordinarily high-quality sound for a variety of applications The MOXF6/MOXF8 draws on the high-quality sound of the famed MOTIF XF, used extensively by artists worldwide, and is equipped with a wide range of dynamic sounds for use in virtually any music application. Furthermore, in one of the most important advantages of the MOXF, an optional Flash Memory Expansion Board can be installed. This feature was included in response to many and repeated requests from power users. Now, Sample (audio) data remains on the board, even when the power is turned off—allowing you to instantly use Waveforms containing Samples when you turn the power back on, without the need to load them from an external USB storage device. FUNCTIONS Instant, smooth translation from inspiration to final music composition The MOXF6/MOXF8 features a powerful Performance Creator function which lets you combine your favorite Voice with other Voices and drum parts, and perform with full rhythmic and chordal backing. You can also record your performances as a Song or Pattern, simply by pressing the [REC] button from Performance mode—and then, after recording, automatically move to the Song/Pattern mode for further editing, refining and completing the Song or Pattern. This workflow is exceptionally smooth and transparent, and lets you create music quickly and easily as the inspiration hits. Seamless music production with Cubase The MOXF6/MOXF8 were developed giving maximum consideration to integration with the Cubase series DAW software made by Steinberg. We’ve enhanced and strengthened the remote control function in connection with Cubase, letting you easily and conveniently control optional parameters on Cubase with the AI KNOB, or by using control templates compatible with various VST instruments to easily control multiple parameters and complex operations on software synthesizers directly from your hardware synthesizer keyboard. DESIGN Stylish design and professional look We also designed the stylish exterior to reflect the professional-level sounds and sophisticated features of the MOXF6/MOXF8, making it an instrument you’ll love to play, and one you’ll feel proud in showing off onstage. Moreover, its value as a live performance instrument is made even greater by its portability. We also took particular care in designing the size and external appearance to make it easy to use, even when combined in a computer music system. 6 MOXF6/MOXF8 Owner’s Manual Accessories • AC adaptor* • USB cable • Owner’s Manual (this book) • Online Manual CD-ROM x 1 (Reference Manual, Synthesizer Parameter Manual, and Data List) • CUBASE AI DOWNLOAD INFORMATION * May not be included in your area. Please check with your Yamaha dealer. Using the MOXF6/MOXF8 Manuals Your MOXF6/MOXF8 synthesizer comes with four different reference guides—the Owner’s Manual (this book), the Reference Manual, the Synthesizer Parameter Manual, and the Data List. While the Owner’s Manual is packaged together with the synthesizer as a hardcopy booklet, this Reference Manual, Synthesizer Parameter Manual, and the Data List are provided as PDF documents on the bundled CD-ROM. • Owner’s Manual (this book) Describes how to set up your MOXF6/MOXF8 and how to perform basic operations. • Reference Manual (this PDF document) Describes the internal design of your MOXF6/MOXF8 and the various parameters that can be adjusted and set. It also describes how to use the instrument in specific applications and provides the following reference materials. • Category lists for the Voices and Performances • Setting examples of the Controller Destination • Functions of Knobs 1 – 8 in Voice mode and Mixing mode • Song playback types • Song Track Loop—setting example • Punch In/Out recording in Song mode • Pattern playback types • Pattern Loop recording • Creating an Arpeggio • Storing the Mixing settings as a Mixing Template • Remote control assignments • File/Folder selection in File mode • Playing back SMF (Standard MIDI file) data from USB flash memory device • Formatting a USB flash memory device • Synthesizer Parameter Manual (PDF document) This general, cross-product document explains the Voice parameters, effect types, effect parameters, and MIDI messages that are used for all synthesizers incorporating the Yamaha AWM2 tone generators. Read the Owner’s Manual and Reference Manual first and then use this parameter manual if necessary to learn more about parameters and terms that relate to Yamaha synthesizers in general. • Data List (PDF document) Provides lists such as the Voice List, Waveform List, Performance List, Effect Type List, Arpeggio Type List, as well as reference materials such as the MIDI Implementation Chart and Remote Control Function List. How to use the PDF manuals The Reference Manual, the Synthesizer Parameter Manual, and the Data List are provided as data documents in PDF format. These PDF files can be viewed and read on a computer. When using Adobe® Reader® to view a PDF file, you can search for specific words, print a specific page or link to open a desired section in the manual. The term search and link functions are especially convenient methods of navigating through a PDF file, and we recommend that you use them. The latest version of Adobe Reader can be downloaded from the following URL. http://www.adobe.com/products/reader MOXF6/MOXF8 Owner’s Manual 7 MOXF6/MOXF8 Main Features  MOTIF XF Sound Engine feature The wide range of dynamic and authentic MOTIF XF waveforms (such as the realistic sounds of acoustic piano, electric piano, synthesizer, strings, wind instruments, drums) are all included in this instrument. The sophisticated XA (Expanded Articulation) function has also been included, providing greater performance flexibility and acoustic realism. It allows you to more effectively recreate realistic sound and natural performance techniques—such as legato and trills—and provides other unique modes for random and alternate sound changes as you play. Moreover, the instrument features new Arpeggio types for Drum Voices, as well as the existing MOTIF XF Arpeggio types, plus an extensive effect system—including VCM (Virtual Circuitry Modeling) Effects, Master Effect, and Master EQ. In a wide variety of ways, the MOXF6/MOXF8 truly enhances your music performance and creation.  Easy-to-use user interface You can select a desired Voice or Performance directly by using the sixteen number buttons. You can also call up desired Voices or Performances according to the instrument type by using the Category Search function. This instrument also provides a powerful, easy-to-use Performance Creator function, which lets you quickly and smoothly create fully realized music, whenever the inspiration strikes you. Use it to easily create new Performances by using favorite Voices you’ve found in the Voice mode.  Comprehensive sequencer for creating Songs and Patterns This instrument features a built-in sequencer which enables you to produce high-quality music, without the need of a computer or any other devices. The sequencer features both Realtime recording, which records your performance data as you play it, and Step recording, which is suitable for recording precise, mechanical phrases or other difficultto-execute passages. Moreover, you can record the Performance as a Song/Pattern simply by pressing the [REC] button, and easily edit and refine your song to completion.  Optional Flash Memory Expansion Module The MOXF provides the option of installing a Flash Memory Expansion Module (FL512M/FL1024M), allowing you to internally store Waveforms that include your sampled audio sounds, and keep those Waveforms intact, even when turning off the power.  Responsive, expressive keyboard The MOXF8 features an 88-key GHS keyboard. This feature provides authentic, realistic keyboard response—much like the playing feel of an acoustic piano—with the lower keys being heavy in touch, the higher keys light, and all the natural gradations in between. The MOXF6 features a newly developed, 61-key, semi-weighted keyboard. The keyboard has been designed and adjusted so that you easily and expressively play the rich variety of sounds of the instrument.  Master Keyboard function This convenient function lets you use this instrument as a master keyboard controller (with independent Zones), and for easily reconfiguring the instrument between Voice/Performance play and Song/Pattern play in live applications.  Stereo A/D INPUT [L]/[R] jacks You can also connect various devices, such as microphone, guitar, or audio equipment, to the Input jacks of the instrument, and have that audio input signal sound as a separate A/D input Part in the Voice/Performance/Song/ Pattern mode. Various parameters such as volume, pan, and effect can be set for this Part, and the sound is output together with all the other Parts, letting you play and output the sound MOXF6/MOXF8 together with the external sound. Also, you can create a vocoder sound by using the input signal from these jacks and the internal effect.  USB Audio/MIDI interface The USB terminal of the instrument serves as both a MIDI and audio interface—letting you record digitally the instrument sound and the audio signal from the A/D INPUT [L]/[R] jacks to DAW software on a computer. You can also output both the instrument sound and the DAW software input signal from the MOXF6/MOXF8.  Integration with Cubase The MOXF is specially designed to work seamlessly with Cubase, Steinberg’s full-featured DAW software — giving you a comprehensive, all-in-one music production system, in which hardware and software are fully integrated. 8 MOXF6/MOXF8 Owner’s Manual Contents A message from the MOXF6/MOXF8 Development Team ...6 Accessories ...........................................................................7 Using the MOXF6/MOXF8 Manuals ......................................7 MOXF6/MOXF8 Main Features.............................................8 Control and Functions Selecting a Performance........................................................... 34 Changing the timbre of the Voice ............................................. 35 Recording in the Performance mode .................................. 36 Song and Pattern ...................................................................... 36 Recording the melody and Arpeggio playback to the Song .... 36 Recording Arpeggio playback to a Pattern .............................. 37 10 Connecting a microphone or audio equipment ................... 38 Top Panel ............................................................................10 Playing the keyboard along with the sound input from the A/D INPUT [L]/[R] jacks ...................................................... 38 Playing the keyboard along with Vocoder ................................ 39 Rear Panel...........................................................................16 Creating an original Song ................................................... 40 Setting Up 17 Power supply .......................................................................17 Connecting speakers or headphones..................................17 Powering up the system ......................................................17 Auto Power Off function.......................................................18 Adjusting the volume and the brightness of the display ......18 Song playback .......................................................................... 41 Creating a Drum part via Step Recording................................. 41 Creating a bass part via Realtime Recording ........................... 43 Creating a synthesizer part by using Arpeggio ........................ 44 Correcting wrong notes............................................................. 45 Completing the Song by editing the Mixing.............................. 45 Storing the created Song .......................................................... 46 Creating an original Pattern ................................................ 47 Playing the Demo Songs .....................................................19 Listening to the Demo Patterns ................................................. 47 Creating a Pattern (Section A) by using Arpeggio.................... 47 Creating another Pattern (Section B) by using already recorded data..................................................... 48 Creating a Pattern Chain for converting to a Song ................... 49 Resetting User Memory to the initial factory settings ..........20 Connecting external MIDI instruments................................ 51 Starting up ...........................................................................19 Selecting programs..............................................................19 Basic Operation 21 Moving the cursor ................................................................21 Changing (editing) parameter values ..................................21 Functions and Sub-Functions..............................................21 Inputting a number directly ..................................................21 Using a Connected Computer ............................................ 53 Connecting to a computer ........................................................ 53 Creating a Song with a computer ............................................. 54 Remote-controlling the software from the MOXF6/MOXF8 (Remote mode) ......................................................................... 55 Using the MOXF6/MOXF8 Editor............................................... 57 Using as a Master Keyboard .............................................. 57 Naming (inputting characters) .............................................22 Registering the Edited Voice/Performance/Song/Pattern ......... 57 Making settings for use as a master keyboard ......................... 58 Selecting a note type ...........................................................22 Making Global System Settings (Utility Mode).................... 58 Note (Key) and Velocity settings .........................................22 Setting the default mode when turning the power on ............... 58 Reversing the LCD status ......................................................... 59 Click (metronome) settings ....................................................... 59 Effect settings applied to the signal input from the A/D INPUT jack ................................................................... 59 Master Effect/Master EQ settings in the Voice mode................ 59 Transmitting Control Change messages using the Foot Switch.......................................................................... 59 Quick Guide 23 Modes..................................................................................23 Basic Instructions ................................................................24 Playing the keyboard in the Voice mode .............................25 Selecting a Preset Voice ........................................................... 25 Using the Category Search function ......................................... 26 Grouping your most-used Voices together— Favorite Category ...................................................................... 26 Using the Arpeggio function ..................................................... 27 Turning the Arpeggio On/Off.............................................. 27 Changing the Arpeggio type .............................................. 27 Keyboard Octave/Transpose setting ........................................ 27 Changing the tonal qualities of the Voice ................................. 28 Editing a Voice .......................................................................... 28 Enhancing the sound with Effects ............................................. 29 Changing the Arpeggio Type assignment ................................ 31 Creating a new Performance by using your favorite Voice (Performance Creator).........................................................31 Saving/Loading Data (File Mode) ....................................... 60 Saving the settings to a USB flash memory device .................. 60 Loading the settings from a USB flash memory device............ 60 Precautions when using the USB [TO DEVICE] terminal .......... 61 Appendix 62 Shift Function List ............................................................... 62 Display Messages............................................................... 63 Troubleshooting .................................................................. 65 Installing Optional Hardware............................................... 70 Available devices ...................................................................... 70 Installation locations.................................................................. 70 Installation Precautions ............................................................. 70 Installing Optional Hardware FL512M/FL1024M....................... 71 Removing the Module ............................................................... 72 Layer—Playing different Voices together.................................. 31 Split—Playing two different Voices with your left and right hands ................................................................................ 32 Drum Assign—Layering a drum Part with the current Voice..... 33 Changing the drum pattern (Arpeggio Type)............................ 33 Specifications...................................................................... 73 Playing the keyboard in the Performance Mode..................34 Index ................................................................................... 74 MOXF6/MOXF8 Owner’s Manual 9 Control and Functions Top Panel MOXF8 6 78 ) @ ^ B 5 2 3 & *( 4 9! A-1 B-1 C0 D0 E0 # $ F0 G0 A0 B0 C1 % A C2 C D C3 1 MOXF6 6 78 ) @ ^ B 5 & *( 4 9! 2 E1 1 MOXF6/MOXF8 Owner’s Manual $ % A C 3 C1 D1 10 # F1 G1 A1 B1 C2 C3 D Control and Functions E F G N H Q ST M C4 C5 F G E P R I J K L O N H I O C6 P C7 Q ST R J K L C4 M C5 C6 MOXF6/MOXF8 Owner’s Manual 11 Control and Functions 1 Keyboard 9 [LEVEL] meter (page 39) The MOXF8 features an 88-key keyboard, while the MOXF6 has 61 keys. All are equipped with a touch response feature, initial touch. With initial touch, the instrument senses how strongly or softly you play the keys, and uses that playing strength to affect the sound in various ways, depending on the selected Voice. Indicates the level of the signal specified via the [LEVEL] meter switch button. ) @ ^ 2 Pitch Bend wheel Controls the pitch bend effect. You can also assign other functions to this controller. & * ( 3 Modulation wheel Controls the modulation effect. You can also assign other functions to this controller. 6 7 8 ! # $ % A ) Knob Function 1 button Pressing this button changes the functions assigned to Knobs 1 – 4 (on the upper row). The lamp next to the currently active parameters will light. In the Voice mode, the function of each knob is applied to the current Voice; in the Performance/Mixing mode, the function of each knob is applied only to the currently selected Part or to all Parts (depending on the setting via the [COMMON] and [PART SELECT] buttons). 5 4 NOTE When you press the Knob Function 1 button while holding the 9 [SHIFT] button, the lamp next to the [TONE 1] button will light and the TONE 1 parameters are assigned to Knobs 1 – 4. 4 [MASTER VOLUME] slider (page 18) ! Knob Function 2 button Adjusts the volume of the overall sound. Move the slider upwards to raise the output level from the OUTPUT [L/MONO]/ [R] jacks and the [PHONES] jack. Pressing this button changes the functions assigned to Knobs 5 – 8 (on the lower row). The lamp next to the currently active parameters will light. 5 [DAW LEVEL] slider Adjusts the volume of the audio signal input from the USB [TO HOST] terminal. NOTE When you press the Knob Function 2 button while holding the [SHIFT] button, the lamp next to the [EQ] button will light and the EQ parameters are assigned to Knobs 5 – 8. @ Knobs 1 – 8 (page 28) 6 A/D INPUT [GAIN] knob (page 39) Use this to adjust the input gain of the audio signals at the A/ D INPUT [L]/[R] jacks. Depending on the connected microphone, you may need to adjust this for optimum level. The volume level is increased as the knob is rotated to the right and decreased as it is rotated to the left. NOTE Depending on the output level of the equipment connected to the A/D INPUT [L]/[R] jacks, you should change the value of the Mic/Line parameter in the [F1] GENERAL display of the Utility mode. When the output level of the connected equipment (such as a microphone, guitar, bass) is low, set this parameter to “mic.” When the output level of the connected equipment (such as a synthesizer keyboard, CD player) is high, set this parameter to “line.” 7 A/D INPUT [ON/OFF] button (page 39) Switches whether or not this instrument accepts the audio signal input via the A/D INPUT [L]/[R] jack. 8 [LEVEL] meter button (page 39) Selects the destination signal controlled via the [LEVEL] meter, input signal via the A/D INPUT [L]/[R] jacks or output signal via the OUTPUT [L/MONO]/[R] jack. 12 MOXF6/MOXF8 Owner’s Manual These eight highly versatile knobs let you adjust various aspects or parameters of the current Voice. In this manual, the knobs on the upper row are called “Knob 1” – “Knob 4” and the knobs on the lower row are called “Knob 5” – “Knob 8.” Pressing the Knob Function 1 button will change the functions of Knobs 1 – 4 while pressing the Knob Function 2 button will change the functions of Knobs 5 – 8. # ASSIGNABLE FUNCTION [1]/[2] buttons Depending on the XA (Expanded Articulation) settings in the Voice Element Edit mode, you can call up the specific Element of the selected Voice by pressing each of these buttons during your keyboard performance. In addition, you can assign other functions to these buttons. $ OCTAVE [-] and [+] buttons (page 27) Use these buttons to change the note range of the keyboard. To restore the normal octave setting, press both buttons simultaneously. Control and Functions % TRANSPOSE [-] and [+] buttons (page 27) [F] (Play) button Use these buttons to raise or lower the pitch of the note in semitone steps. To restore the normal octave setting, press both buttons simultaneously. Press to start playback/recording from the current point in the Song or Pattern. During recording and playback, the indicator flashes at the current tempo. ^ EFFECT buttons The extensive effect block of the instrument provides Insertion Effects (eight sets), System Effects (Reverb and Chorus), and Master Effects. The effects can be applied to the keyboard played Voices and to Song/Pattern playback. When the lamp of the [INSERTION], [SYSTEM] or [MASTER] button is turned on, the corresponding Effect is available. B NOTE When the Reverb/Chorus of the “SystemFXOn/OffBtn” parameter D is set to off in the [UTILITY]  [F1] GENERAL  [SF1] TG display, the Reverb/Chorus will not function even if the EFFECT [SYSTEM] button is turned off. & ARP [ON/OFF] button (page 27) Press this button to enable or disable playback of the Arpeggio for each Voice, Performance, Song, or Pattern. If the Arpeggio Switch of the selected Part is set to off in the Performance/Song/Pattern mode, however, pressing this button has no effect. C B LCD (Liquid Crystal Display) The backlit LCD indicates the parameters and values related to the currently selected operation or mode. C [F1] – [F6] (Function) buttons (page 21) * ARP [EDIT] button (page 31) Press this button to call up the Arpeggio Edit display of the Voice/Performance /Song/Pattern mode. When the Arpeggio Edit display is shown with the [E] (Edit indicator) called up by editing a parameter, press the ARP [EDIT] button (the lamp flashes) to call up the Compare status. This restores the original, unedited setting. In the Compare status, the [E] indication is replaced by [C]. Press the ARP [EDIT] button again to exit from the Compare status. ( [DAW REMOTE] button (page 55) Turn on this button to enter the Remote mode. The Remote mode lets you control DAW software on your computer from the panel controls of the instrument. These buttons located directly below the LCD call up the corresponding functions indicated in the display. D [SF1] – [SF6] (Sub Function) buttons (page 21) These buttons located directly below the display call up the corresponding sub functions indicated in the display. These buttons can be also used to call up different Arpeggio types in some displays of the Play mode and Record mode (page 27). These buttons can be also used as Song Scene buttons in Song Play/Song Record (see the “Reference Manual” PDF document). A SEQ TRANSPORT button (page 19) These buttons control recording and playback of the Song/ Pattern sequence data. [P] (Top) button Instantly returns to the beginning of the current Song or Pattern (i.e., the first beat of the first measure). [G] (Reverse) button Press briefly to move back one measure at a time, or hold to continuously rewind. [H] (Forward) button Press briefly to move forward one measure at a time, or hold to continuously fast-forward. [REC] (Record) button Press this to enable recording (Song or Pattern phrase). (The indicator lights.) [J] (Stop) button Press to stop recording or playback. MOXF6/MOXF8 Owner’s Manual 13 Control and Functions E F according to a hierarchical structure. Press this button to exit from the current display and return to the previous level in the hierarchy. Also use it to cancel a Job or a Store operation. G M [ENTER] button H Use this button to call up the display of the selected menu. Also use this button to execute a Job or a Store operation. I J N K L O P Q M E [CATEGORY SEARCH] button (page 26) In the Voice/Performance Part Edit/Song/Pattern mode, turn this button on to call up the Category Search display of the Voice assigned to the current Part. In this status, the [A] – [H] buttons can be used for selecting the Main Category of the Voice. In the Performance mode (except for the Part Edit mode), turn on this button to call up the Category Search display of the current Performance. In this status, the [A] – [H] buttons can be used for selecting the Main Category of the Performance. N [MODE] buttons F [FAVORITE] button These buttons select the MOXF6/MOXF8 operating modes (e.g., Voice mode). Use this convenient function to store all your favorite, oftenused Voices/Performances in a single, easy-to-access location and call them up by pressing the [FAVORITE] button. You can add the current program to a favorite category by simultaneously holding down the [SHIFT] button and pressing this button. This is one more useful way you can quickly select the Voices/Performances you need from the huge number available on the instrument. G [DATA] dial For editing the currently selected parameter. To increase the value, turn the dial right (clockwise); to decrease the value, turn the dial left (counter-clockwise). If a parameter with a wide value range is selected, you can change the value in broader strokes by quickly turning the dial. O PERFORMANCE CREATOR (page 31) This function is for quickly editing/creating a new Performance based on the current Voice. This would come in handy when a certain Voice has effect settings that you want to use in your Performance program. [LAYER] button This button is for editing a layer Performance based on the current Voice. When pressing this button, the Category Search display appears and you can select the Voices for use in a layer. [SPLIT] button H [INC] button This button is for editing a split Performance based on the current Voice. When pressing this button, the Category Search display appears and you can select the Voices for use in a split. For increasing the value of the currently selected parameter. [DRUM ASSIGN] button I [DEC] button For decreasing the value of the currently selected parameter. NOTE Simultaneously hold down the [SHIFT] button and press the [INC] button to quickly increase the parameter value in 10-step jumps. Simultaneously hold down the [SHIFT] button and press the [DEC] button to quickly decrease the parameter value in 10-step jumps. This button is for editing a Performance with a Drum Voice based on the current Voice. When pressing this button, the Category Search display appears and you can select the desired Drum Voice. Also, Arpeggio will be set to on automatically. P BANK SELECT [DEC]/[INC] buttons J Cursor buttons Use these buttons to select the desired Voice or Performance Bank. The cursor buttons move the “cursor” around the display, highlighting and selecting the various parameters. Q Group [A] – [H] buttons Pressing this button along with another button enables you to execute various commands. For details, refer to the “Shift Function List” (page 62). Use these buttons to select the desired Group of Voices/ Performances. When the [CATEGORY SEARCH] button is turned on, these buttons can be used to select a category. When the [QUICK SETUP] button is turned on, these buttons can be used to select a Quick Setup. L [EXIT] button R [COMMON] button The menus and displays of the MOXF6/MOXF8 are organized Turning this button on enters Common Edit, which lets you K [SHIFT] button 14 R MOXF6/MOXF8 Owner’s Manual Control and Functions edit the parameters commonly applied to all Elements, Parts or Zones in the following modes: Voice Edit, Performance, Song/Pattern Mixing Edit, Mixing Voice Edit and Master Edit. on/off for each Zone. For details about this function, see the “Reference Manual” PDF document. T [TRACK] button S T Turning this button on in the Song/Pattern mode enables the Number [1] – [16] buttons for selecting corresponding Song/ Pattern Tracks. In the Voice mode/Performance mode, this button lets you use the Number buttons to select the Keyboard Transmit Channel. [MUTE] button (page 41) S [PATTERN SECTION/PERFORMANCE CONTROL] button This button is available in the Performance mode, Pattern mode and Master mode. In the Performance mode, turning on this button will assign the following functions to the Number [1] – [16] buttons. Number button Turning this button on in Normal Voice Edit and Mixing Voice Edit enables the Number [9] – [16] buttons for muting Voice Elements (1 – 8). Turning this button on in the other modes enables the Number [1] – [16] buttons for muting Performance Parts (1 – 4), Song Tracks/Parts (1 – 16), and Pattern Tracks/Parts (1 – 16). [SOLO] button (page 41) Function [1] – [4] Selecting Performance Parts 1 – 4. [5] – [8] Setting the Arpeggio Switch to on/off for Performance Parts 1 – 4. [9] – [12] Setting the mute status for Performance Parts 1 – 4. [13] – [16] Setting the Arpeggio Hold for Performance Parts 1 – 4. In the Pattern mode, turning on this button will assign Sections A – H to the Number [1] – [16] buttons. In the Master mode, turning on this button lets you use the Number buttons to switch the Internal Switch/External Switch Turning this button on in Normal Voice Edit and Mixing Voice Edit enables the Number [9] – [16] buttons for soloing a Voice Element (1 – 8). Turning this button on in the other modes enables the Number [1] – [16] buttons for soloing a Performance Part (1 – 4), a Song Track/Part (1 – 16), and a Pattern Track/Part (1 – 16). NOTE The on/off status of buttons T – affects the Number [1] – [16] buttons in different ways, depending on the currently selected mode. Refer to the table below. Number [1] – [16] buttons Use of these buttons differs depending on the on/off status of the [PATTERN SECTION/PERFORMANCE CONTROL], [TRACK], [MUTE] and [SOLO] buttons. Functions of the Number [1] – [16] buttons Mode When the [PATTERN SECTION/ PERFORMANCE CONTROL] button is turned on: When the [TRACK] button is turned on: Voice Play – Keyboard transmit channel setting Normal Voice Edit – Changes the Edit mode from Common Edit to Element Edit and Element selection ([1] –[8]). Drum Voice Edit – Changes the Edit mode from Common Edit to Drum Key Edit When the [MUTE] button is turned on: When the [SOLO] button is turned on: – – Element Mute setting ([9] – [16]) – When all the buttons are turned off: Voice selection Solo Element selection ([9] – [16]) – – – Performance Play Performance Control (S) Keyboard transmit channel setting Part Mute setting ([1] – [4]) Solo Part selection ([1] – [4]) Performance Edit Performance Control (S) Performance Part selection ([1] – [4]) Part Mute setting ([1] – [4]) Solo Part selection ([1] – [4]) Master Play – Keyboard transmit channel setting (when memorizing the Voice mode or Performance mode to the current Master) or Song/Pattern Track selection (when memorizing the Song mode or Pattern mode to the current Master) – – Master Edit – Changes the Edit mode from Common Edit to Zone Edit and Zone selection ([1] – [4]) – – Performance selection – Master program selection – Song/Pattern Play Section selection in the Pattern mode Song/Pattern Track selection Song/Pattern Track Mute setting Solo Track selection Song/Pattern selection Song/Pattern Mixing Section selection in the Pattern mode Song/Pattern Part selection Song/Pattern Part Mute setting Solo Part selection Voice selection of the current Part Element selection ([1] – [8]) Element Mute setting ([9] – [16]) Solo Element selection ([9] – [16]) Mixing Voice Edit – – MOXF6/MOXF8 Owner’s Manual 15 Control and Functions Rear Panel 3 1 5 6 7 8 9 2 1 P Standby/On switch (page 17) Press to turn the power On (O) or Standby (N). [ASSIGNABLE], it can control one of various different assignable functions. 2 DC IN connector (page 17) 6 [FOOT CONTROLLER] jack Connect the supplied power adaptor to this connector. For connection of an optional foot controller (FC7, etc.). This jack lets you continuously control one of various different assignable functions—such as volume, tone, pitch, or other aspects of the sound. 3 USB terminals There are two different types of USB terminals, and the rear panel of the instrument features both. The USB [TO HOST] terminal is used to connect this instrument to the computer via the USB cable and allows you to transfer MIDI data and audio data between the devices. Unlike MIDI, USB can handle multiple ports via a single cable. For information about the Port handled by the MOXF6/ MOXF8, see page 54. The USB [TO DEVICE] terminal is used to connect this instrument to a USB flash memory device via the USB cable. This lets you save data created on this instrument to an external USB flash memory device and load data from a USB flash memory device to the instrument. Save/Load operations can be performed in the File mode (page 60). NOTE Only USB flash memory device can be recognized by this instrument. Any other USB storage devices (such as hard disk drive, CD-ROM drive and USB hub) cannot be used. NOTE Though the instrument supports the USB 1.1 standard, you can connect and use a USB 2.0 storage device with the instrument. However, note that the transfer speed is that of USB 1.1. 4 MIDI [IN] / [OUT] / [THRU] terminals MIDI [IN] is for receiving control or performance data from another MIDI device, such as an external sequencer, letting you control this instrument from the connected separate MIDI device. MIDI [OUT] is for transmitting all control, performance and playback data from this instrument to another MIDI device, such as an external sequencer. MIDI [THRU] is simply for redirecting any received MIDI data (via MIDI [IN]) to connected devices, allowing convenient chaining of additional MIDI instruments. 5 FOOT SWITCH [ASSIGNABLE]/[SUSTAIN] jacks For connection of an optional FC3/FC4/FC5 Footswitch to the [SUSTAIN] jack and a FC4/FC5 Footswitch to the [ASSIGNABLE] jack. When connected to the [SUSTAIN] jack, the Footswitch controls sustain. When connected to 16 4 MOXF6/MOXF8 Owner’s Manual 7 OUTPUT [L/MONO] and [R] jacks Line level audio signals are output via these phone jacks. For monophonic output, use only the [L/MONO] jack. 8 [PHONES] (Headphone) jack This standard stereo phones jack is for connection to a set of stereo headphones. This jack outputs audio signals identical to those from the OUTPUT [L/MONO] and [R] jacks 9 A/D INPUT [L] and [R] jacks External audio signals can be input via these phone jacks (mono phone plug). Various devices such as microphone, guitar, bass, CD player, synthesizer can be connected to these jacks and their audio input signal can be sounded as the Audio Part of the Voice, Performance, Song, or Pattern. In addition, you can use the special Vocoder feature (page 39) by connecting a microphone to one of these jacks and inputting your Voice to the microphone. Use mono phone plugs. For stereo signals (such as from audio equipment), use both jacks. For mono signals (such as from a microphone or guitar), use only one of these jacks according to the “Mono/Stereo” parameter setting. NOTE When using these jacks, make sure to confirm the “Mono/Stereo” parameter setting which can be set in the following displays for each mode: • For the Voice mode: the VCE A/D display in the Utility mode • For the Performance mode: the A/D IN display in Common Edit • For the Song/Pattern mode: the A/D IN display in Mixing Common Edit Setting Up Power supply Make connections for the supplied power adaptor (page 73) in the following order. Before you connect the power adaptor, make sure that the power of this instrument is set to the Standby status. 1 Connect the plug of the power adaptor to the DC IN terminal on the rear panel. 2 Connect the other end of the power adaptor to an AC outlet. 1 DC IN 2 Power adaptor plug Connecting speakers or headphones Since this instrument has no built-in speakers, you will need to monitor the sound of the instrument by using external equipment. Connect a set of headphones, powered speakers, or other playback equipment as illustrated below. When making connections, be sure that your cables have the appropriate ratings. Powered speaker (Left) Powered speaker (Right) Headphones AC outlet OUTPUT L/MONO OUTPUT R PHONES NOTE Follow this procedure in reverse order when disconnecting the power adaptor. MOXF6/MOXF8 WARNING Use the specified adaptor (page 73). The use of other adaptors may result in irreparable damage to both the adaptor and the instrument. CAUTION • Make sure your MOXF6/MOXF8 is rated for the AC voltage supplied in the area in which it is to be used (as listed on the rear panel). Connecting the unit to the wrong AC supply can cause serious damage to the internal circuitry and may even pose a shock hazard! • Even when the power of this instrument is in the Standby status, electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure you unplug the power adaptor from the wall AC outlet. Powering up the system Make sure the volume settings of this instrument and external devices such as powered speakers are turned down to the minimum before turning the power on. When connecting this instrument to the powered speakers, turn on the power switch of each device in the following order. When turning the power on: First, the MOXF6/MOXF8, then the connected powered speakers. When turning the power off: First, the connected powered speakers, then the MOXF6/ MOXF8. Please keep in mind that the Standby/On switch is located at the right end (from the view of the keyboard) on the rear panel of the MOXF6/MOXF8. DC IN Standby/ On switch MOXF6/MOXF8 MOXF6/MOXF8 Owner’s Manual 17 Setting Up Auto Power Off function To prevent unnecessary power consumption, this instrument features an Auto Power Off function that automatically turns the power off if the instrument is not operated for a specified period of time.  Auto Power Off Setting The amount of time that elapses before the power is automatically turned off can be set. Instructions: [UTILITY]  [F1] GENERAL  [SF6] OTHER  Set “AutoOff”  [STORE] Setting Value (min.): off (Disables Auto Power Off), 5, 10, 15, 30, 60, 120 Default Setting (min.): 30  Disabling Auto Power Off (simple method) Adjusting the volume and the brightness of the display Adjust the volume levels of this instrument and the connected amplifier/speaker system. NOTE When connecting to a set of powered speakers or PA equipment, set the MASTER VOLUME to about 70%, then raise the volume of the powered speakers or PA equipment to the appropriate level. If the display is not easily visible, press the [INC]/[DEC] button while holding the [UTILITY] button to adjust for optimum visibility. Adjust the volume with the MASTER VOLUME slider. Adjust the display contrast. Max. Min. Turn the power on while holding down the lowest key on the keyboard. A “Auto power off disabled.” indication appears briefly and Auto Power Off is disabled. The setting is retained even if the power is turned off. MOXF6/MOXF8 CAUTION Do not listen with the headphones at high volume for long periods of time. Doing so may cause hearing loss. NOTICE • Even when the power is turned off, electricity is still flowing to the instrument at the minimum level. To shut off the electricity completely, make sure you unplug the power cord from the wall AC outlet. • Depending on the instrument status, the power may not turn off automatically, even after the elapse of the specified period of time. Always turn off the power manually when the instrument is not in use. • When the instrument is not operated for a specified period of time while connected to an external device such as an amplifier, speaker or computer, make sure to follow the instructions in the Owner’s Manual to turn off the power to the instrument and the connected devices, in order to protect the devices from damage. If you do not want the power to turn off automatically when a device is connected, disable Auto Power Off. • The setting will revert to its default value if not backed up before the power is turned off. • When Auto Power Off is set to “off,” the value will be retained even if the backup data saved on another device is loaded to the instrument. When Auto Power Off is set to something other than “off,” the value will be overwritten with loaded data. NOTE The setting time is approximate. NOTE To turn the power on after Auto Power Off has been executed, press the Standby/On switch once to the Standby position, and then press it again to the On position. NOTE When the factory settings are restored, the setting time is changed to the default value (30 min.). 18 MOXF6/MOXF8 Owner’s Manual Setting Up Starting up Playing the Demo Songs Try playing some of the realistic and dynamic MOXF6/ MOXF8 sounds from the keyboard now. When you turn the power on, the display below appears. The MOXF6/MOXF8 features a variety of Demo Songs, showcasing its dynamic sound and sophisticated functions. Here’s how to play them back. Program name 1 Master program number Press the [SONG] button to enter the Song Play mode. The PLAY display appears. 2 Mode Bank Press the SEQ TRANSPORT [F] (Play) button to start the Demo Song. The Song currently shown on the display starts. Program number NOTE In the default settings, the Master mode is selected. See page 23 for details about the modes. NOTE Keep in mind that the example displays shown in this manual are for instruction purposes only, and may appear somewhat different from those on your instrument. In this condition you can play the keyboard and hear the sounds of the selected program. In the default setting, the Master mode provides a total of 128 programs each of which includes the mode (Voice, Performance, Song, Pattern) and its program number. The top of the Master Play display indicates the Master program number and the status (Mode, Bank, Program number and its name) registered to the current Master program. NOTE For details about Banks, see pages 25 and 34. Selecting programs Stop button Play button NOTE To adjust the volume level of the Demo Songs, use the [MASTER VOLUME] slider. 3 Press the SEQ TRANSPORT [J] (Stop) button to stop the Demo Song. 4 Select another Demo Song by using the [INC] button or [DATA] dial. 5 Play the selected Demo Song by performing Steps 2 and 3. In the default setting, the Master mode provides a total of 128 programs each of which includes the mode (Voice, Performance, Song and Pattern) and its program number. Try out the different Master programs to play various Voices and Performances. You can change the Master program number by using the [INC] button, [DEC] button, or [DATA] dial. Decreases number Increases number Decreases number Increases number MOXF6/MOXF8 Owner’s Manual 19 Setting Up Resetting User Memory to the initial factory settings The original factory settings of this synthesizer’s User Memory can be restored as follows. NOTICE When the factory settings are restored, all the Voice, Performance, Song, Pattern, and system settings in the Utility mode you created will be erased. Make sure you are not overwriting any important data. Be sure to save all important data to your USB flash memory device before executing this procedure (page 60). 1 Press the [UTILITY] button then the [JOB] button to call up the Factory Set display. 2 Press the [ENTER] button. The display prompts you for confirmation. To cancel this operation, press the [EXIT] button here. NOTICE When entering a checkmark to the box of Power On Auto Factory Set and executing Factory Set, the Factory Set operation will automatically be executed each time you turn the power on. Keep in mind that this also means that your original data in Flash ROM will be erased each time you turn on the power. Therefore, the checkmark of this box should normally be removed. If you remove the checkmark of this box and execute Factory Set, the Factory Set operation will not be executed when turning the power on the next time. 3 Press the [ENTER] button to execute Factory Set. After Factory Set has been completed, a “Completed” message appears and operation returns to the original display. NOTICE For Factory Set operations that take longer to process, you will see the message “Now executing Factory Set…” during processing. While such a message is shown on the display, never attempt to turn off the power. Turning the power off in this state results in loss of all user data and may cause the system to freeze (due to corruption of data in the Flash ROM). This means that this synthesizer may not be able to start up properly, even when turning the power on next time. 20 MOXF6/MOXF8 Owner’s Manual Basic Operation Moving the cursor Use these four buttons to navigate the display, moving the cursor around the various selectable items and parameters in the screen. When selected, the relevant item is highlighted (the cursor appears as a dark block with inverse characters). You can change the value of the item (parameter) at which the cursor is located by using the [DATA] dial, [INC] and [DEC] buttons. Changing (editing) parameter values Rotating the [DATA] dial to the right (clockwise) increases the value, while rotating it to the left (counter-clockwise) decreases it. Pressing the [INC] button increases a parameter value by one step, and pressing [DEC] decreases it. Pressing and holding either button continuously increases or decreases the value. For parameters with large value ranges, you can increase the value by 10 by simultaneously holding down the [SHIFT] button and pressing the [INC] button. To decrease by 10, simultaneously hold down the [SHIFT] button and press the [DEC] button. Decreases number Decreases number Increases number called up with the [SF1] – [SF6] buttons. Keep in mind that the available sub-functions differ depending on the selected function. The example display below is called up by pressing the [F5] LFO button then pressing the [SF1] Wave button. In this example display, no sub-function is assigned to the [SF6] button. These functions can be selected via the corresponding button ([F1] – [F6]). These functions can be selected via the corresponding button ([SF1] – [SF6]). Inputting a number directly For parameters having large value ranges, you can also enter the value directly, using the buttons below the LCD as a numeric keypad. When the cursor is located on such a parameter, the [NUM] icon appears at the lower right corner of the LCD. When the [SF6] NUM button is pressed in this status, each digit (1 – 9, 0) is assigned to the [SF1] – [SF5] and [F1] – [F5] buttons as shown below, allowing you to input a number directly by using these buttons. Depending on the selected parameter, a negative value can be input. When such a parameter is selected and you wish to input a negative value, press the [F6] button (to which “-” is assigned) then use the [SF1] – [SF5] and [F1] – [F5] buttons. After completing the number input, press the [ENTER] button to actually enter the number and exit from this status. Increases number Functions and Sub-Functions Each mode described above contains various displays, with various functions and parameters. To navigate your way through these displays and select a desired function, use the [F1] – [F6] buttons and the [SF1] – [SF6] buttons. When you select a mode, the available displays or menus appear directly above the buttons at the bottom of the display (as shown below). Depending on the currently selected mode, up to six functions are available and can be called up with the [F1] – [F6] buttons. Keep in mind that the available functions differ depending on the selected mode. Depending on the currently selected function, up to six sub-functions are available and can be You can use these buttons as a numeric keypad. MOXF6/MOXF8 Owner’s Manual 21 Basic Operation Naming (inputting characters) Selecting a note type You can freely name the data you’ve created, such as Voices, Performances, Songs, Patterns and files saved to a USB flash memory device. When the cursor is located on such a naming parameter, the “CHAR” icon appears at the lower right corner of the display. When pressing the [SF6] button in this status, the Input Character window appears as shown below. In the Edit area, you can move the cursor to determine the location at which the character is to be input by pressing the [<] or [>] button while holding the [SF6] button. In the Character List, you can move the cursor to determine the character to be input by rotating the [DATA] dial or pressing the [INC] or [DEC] button while holding the [SHIFT] button. After completing the character input, press the [ENTER] button to actually enter the currently edited name and exit from this status. When the cursor is located on a parameter for which note types are to be set, the note icon appears at the lower right corner indicating that you can call up the Note Type selection window by pressing the [SF6] button. You can specify the note type by pressing the [F1] – [F5] buttons and the [SF1] – [SF5] buttons. Note Type selection window Editing area Character List Note (Key) and Velocity settings Several parameters let you set a key range or velocity range for a function—for example, in setting up a keyboard split—by specifying certain note values. You can use the [INC] and [DEC] buttons or [DATA] dial to set these parameters, or you can directly enter the values from the keyboard by pressing the appropriate keys. When the cursor is located on such a parameter, the “KBD” icon appears at the lower right corner of the display. You can set the note or velocity directly from the keyboard by holding down the [SF6] button and pressing the desired key. 22 MOXF6/MOXF8 Owner’s Manual Quick Guide Modes There are several operation modes in this instrument, and they can be selected by using the ten Mode buttons, 1 – ). In addition, there are three “global” modes (Edit, Job and Store) common to all of these modes, and they can be selected by using buttons ! – #. No. Button Mode ) 1 2 3 4 5 6 7 8 9 ! @ # Description 1 [VOICE] Voice mode This synthesizer has a wealth of high quality, dynamic sounds—also referred to as “Voices.” You can play these Voices—one Voice at a time—from the keyboard in the Voice mode. This mode also lets you create your own original Voices. 2 [PERFORM] Performance mode This mode lets you play and create Performances. A Performance lets you put several different Voices together in layers or play different two Voices in a keyboard split. 3 [MASTER] Master mode This mode lets you register settings that you often use in the Voice, Performance, Song or Pattern mode, and instantly recall the relevant mode and custom settings together in a single button press—without having to first select a mode. In addition, this mode lets you divide the keyboard into four separate sections—just as if you were playing four different MIDI keyboards. 4 [SONG] Song mode This mode lets you record, edit and play your own original Songs. 5 [PATTERN] Pattern mode This mode lets you play, record, edit and play your own original rhythm patterns, which can be used to make up a Song. 6 [MIXING] Song Mixing mode/ Pattern Mixing mode This mode lets you set up detailed parameters of the multi-timbral tone generator for use with Song/ Pattern playback. 7 [FILE] File mode This mode lets you save data you’ve created on this instrument to a USB flash memory device, and allows you to load data from the USB flash memory device to the MOXF6/MOXF8. 8 [UTILITY] Utility mode This mode lets you set parameters that apply to the entire system of this instrument. 9 [QUICK SETUP] Quick Setup mode This mode lets you register up to six settings for MIDI connection and Audio connection between this instrument and the computer as “Quick Setups,” and instantly recall the custom settings with a single button press. ) [DAW REMOTE] Remote mode This mode lets you control DAW software on your computer from the panel controls of the instrument. ! [EDIT] Edit This mode lets you edit various parameters in each of the Voice, Performance, Song, Pattern and Master modes. @ [JOB] Job This mode lets you execute various commands such as Initialize, Copy, and MIDI data conversion—useful for creating your original programs. # [STORE] Store This mode lets you store the edited program to internal memory. MOXF6/MOXF8 Owner’s Manual 23 Quick Guide Basic Instructions Voices—the basic building blocks of the MOXF6/MOXF8 Selecting a Preset Voice ..................................................................................................... page 25 Editing a Voice .................................................................................................................... page 28 Combining several Voices to create a Performance Creating a new Performance in the Voice mode by using your favorite Voices (Performance Creator) ........................................................................................................ page 31 Selecting a Performance..................................................................................................... page 34 Editing a Performance ........................................................................................................ page 34 Connecting a microphone or audio equipment Playing the keyboard along with the sound input from the A/D INPUT [L]/[R] jacks ........... page 38 Song/Pattern—created by recording your keyboard performance and assembling Pattern sections Creating an original Song ................................................................................................... page 40 Creating an original Pattern ................................................................................................ page 47 Master mode—create a master keyboard setup or instantly call up your desired programs Using as a Master Keyboard (Master Mode) ...................................................................... page 57 Music creation by using a computer Recording your performance on the MOXF6/MOXF8 to DAW ............................................ page 54 Using the MOXF6/MOXF8 as a tone generator for DAW playback ..................................... page 55 Remote-controlling the DAW (Remote mode)..................................................................... page 55 Using the MOXF6/MOXF8 Editor VST as a software synthesizer....................................... page 57 Global settings and data backup Making global system settings (Utility mode/Quick Setup) ................................................. page 58 Saving / loading data in the File mode................................................................................ page 60 24 MOXF6/MOXF8 Owner’s Manual Quick Guide Playing the keyboard in the Voice mode display, you can select the desired Voice from various Voice Banks and play it. NOTE For details about Voices, refer to “Basic Structure.” For a list of the Preset Voices, refer to the separate Data List PDF file. In the Voice Play display (the top display of the Voice mode), you can select and play a single Voice. The Voices of this instrument are divided into the following two types: Normal Voice Normal Voices are mainly pitched musical instrument type sounds (piano, organ, guitar, etc.) that can be played over the range of the keyboard. Selecting a Preset Voice 1 Press the [VOICE] button. This calls up the Voice Play display. (The [VOICE] button lamp lights.) Drum Voice Drum Voices are mainly percussion/drum sounds that are assigned to individual notes. These Voices are used to perform rhythm parts. 2 Select a Voice Bank with the BANK SELECT [DEC]/[INC] buttons. In this condition, playing the keyboard sounds the Voice indicated in the display. The parameters shown in the Voice Play display are briefly explained below. This instrument features Banks for memorizing Voices. There are basically three different types of Banks: Preset, User, and GM. The contained Voices and features depend on the Bank as described below. I Voice Play display Main Category Bank Program number Sub Category Preset Banks The Preset Banks contain a full set of specially programmed Voices. Voices you've edited yourself cannot be saved in the Preset Banks. User Banks Voice name The User Banks contain the Voices you have edited and stored. By default, these are comprised of Preset Voices. I Normal Voice Banks There are 13 different banks for the Normal Voices: PRE1 – 9 (Preset Banks), USR1 – 3 (User Banks), GM (GM Bank). NOTICE If a Voice in a User Bank (User Voice) is overwritten or replaced, that User Voice will be lost. When you store an edited Voice, be careful not to overwrite any important User Voices. I Drum Voice Banks There are 3 different banks for the Drum Voices: PDR (Preset NOTE You can also conveniently use the User Bank to save desired Drum Bank), UDR (User Drum Bank), GMDR (GM Drum Voices in consecutive order for live performance situations. GM Bank Bank). 3 The GM Bank contains the Voices allocated according to the GM standard. NOTE You can use the [DATA] dial or [INC]/[DEC] buttons to select the Voice number. This operation lets you call up Voices in subsequent or previous Banks. GM Voice GM (General MIDI) is a worldwide standard for Voice organization and MIDI functions of synthesizers and tone generators. It was designed primarily to ensure that any Song data created with a specific GM device would sound virtually the same on any other GM device—no matter the manufacturer or the model. The GM Voice bank on this synthesizer is designed to appropriately play back GM Song data. However, keep in mind that the sound may not be exactly the same as played by the original tone generator. Select a Voice with the [DATA] dial or [INC]/[DEC] buttons. NOTE To quickly move forward through the program (Voice) numbers in 10-step jumps, simultaneously hold down the [SHIFT] button and press the [INC] button in the Play display. To decrease by 10, do the opposite; simultaneously hold down the [SHIFT] button and press the [DEC] button. 4 Play the keyboard. In the Voice mode, a total of 16 Banks (Preset Bank 1 – 9, User Bank 1 – 3, GM Bank, Preset Drum Bank, User Drum, GM Drum Bank) are available. Each of these Banks includes the Voices according to the Voice type. In the Voice Play MOXF6/MOXF8 Owner’s Manual 25 Quick Guide Using the Category Search function Grouping your most-used Voices together—Favorite Category The Voices are conveniently divided into specific Categories, irrespective of their bank locations. The categories are divided based on the general instrument type or sound characteristics. The Category Search function gives you quick access to the sounds you want. Category Search also has a convenient Favorite Category that lets you collect your most often used and favorite Voices for easy selection. This is one more useful way you can quickly select the Voices you need from the huge number available on the instrument. 1 Press the [CATEGORY SEARCH] button in the Voice Play display. Registering your favorite Voices to the Favorite Category The Category Search display appears. Main Category 1 Perform steps 1 through 4 of the “Using the Category Search function” instructions to call up the Voice List of the selected Category. 2 Select the desired Voice with the Cursor [u]/[d] buttons or [DATA] dial. 3 Press the [F5] SET/CLR button to turn on the Favorite mark. Sub Category 2 Move the cursor position to “Main” (Main Category) with the Cursor [u] button, and use the [DATA] dial to select the Main Category. This operation will turn on the Favorite mark, making it solid ( ), and the selected Voice will be registered to the Favorite Category. Pressing the [F5] SET/CLR button again will turn 3 off or “ghost” the Favorite mark ( Move the cursor position to “Sub” (Sub Category) with the Cursor [d] button, and use the [DATA] dial to select the Sub Category. ). To register other Voices, repeat steps 2 through 3. To remove all the Voices from the Favorite Category, press the [F6] CLR ALL button. 4 Press the [ENTER] button, or Cursor [>] button to actually call up the selected Category. Favorite marks The Voice List of the selected category is shown. Main Category icon Voice list of the currently selected category. 4 Sub Category When you complete registering Voices to the Favorite Category, press the [ENTER] button to return to the Voice Play display. This operation will exit from the Category Search display and store the Favorite Category settings to internal Flash ROM. 5 Select the Voice with the Cursor [u]/[d] buttons or [DATA] dial. If you want to change the Category, press the Cursor [<] button or [EXIT] button and go back to step 2. 6 Press the [ENTER] button to actually call up the Voice. This closes the Category Search display. 26 MOXF6/MOXF8 Owner’s Manual To register/remove the current Voice to/from the Favorite Category, simply hold the [SHIFT] button then press the [FAVORITE] button. Quick Guide Selecting a Voice from the Favorite Category 1 Press the [FAVORITE] button in the Voice Play display. The list of Voices registered to the Favorite Category will be shown. 2 Select the Voice with the Cursor [u]/[d] buttons or [DATA] dial. 3 Press the [ENTER] button to actually call up the Voice. Changing the Arpeggio type Arpeggio types are assigned to each of the [SF1] – [SF6] buttons, the corresponding tabs of which are indicated by 8th note icons ( ) at the right of “ARP1” – “ARP6.” This means that you can change the Arpeggio type by pressing the [SF1] – [SF6] buttons as desired. ARP1 – ARP6 buttons Using the Arpeggio function The Arpeggio function automatically triggers preset arpeggio phrases, riffs, and rhythmic patterns according to the notes you play. It not only provides inspiration and full rhythmic passages over which you can perform, it gives you quality MIDI data you can use in creating Songs, or fully formed backing parts to be used in your live performances. You can assign the desired six Arpeggio Types to each Voice. You can also assign the desired six Arpeggio Types to each Part of each Performance/Song/Pattern and play back the Arpeggios of up to four Parts simultaneously. You can also set the Arpeggio playback method, Note range, Velocity range and Play Effects to create your own original grooves. What’s more, Arpeggio playback can be transmitted through MIDI Out, letting you record the Arpeggio data to a sequencer. NOTE For details about Arpeggio, see the “Reference Manual” PDF document. Turning the Arpeggio On/Off To turn Arpeggio playback on or off, press the ARP [ON/OFF] button on the panel. NOTE For information on setting the Arpeggio Type, refer to “Changing the Arpeggio Type assignment” on page 31. Keyboard Octave/Transpose setting To shift the pitch range in playing the keyboard, use the OCTAVE [-]/[+] buttons and TRANSPOSE [-]/[+] buttons. I Octave The OCTAVE [-]/[+] button lets you shift the pitch of the keyboard in octaves, up to a maximum of three. For example, you may want to shift the pitch down lower to get extra bass notes, or shift up to get higher notes for leads and solos. The OCTAVE [-]/[+] controls let you do this quickly and easily. The range is from -3 to +3, with 0 being standard pitch. Pressing the [-] and the [+] buttons together at the same time will return the setting to the initial value (0). The current octave range can be confirmed via the status of the lamp of the OCTAVE [-]/[+] buttons. When set to one octave down or up, the corresponding lamp lights. When set to two octaves down or up, the corresponding lamp flashes slowly. When set to three octaves down or up, the corresponding lamp flashes quickly. I Transpose The TRANSPOSE [-]/[+] button lets you shift the pitch of the keyboard in semitones (up to 11 semitones). This function allows you to play in the same position and with the same fingering, even if the Song data or another instrument player is playing in a different key. The Transpose Up/Down controls let you do this quickly and easily. Pressing the [-] and the [+] buttons together at the same time will return the setting to the initial value (0). When set to one semitone down or up, the corresponding lamp lights. MOXF6/MOXF8 Owner’s Manual 27 Quick Guide NOTE This parameter is same as “Octave” and “Transpose” in the Function of currently operated Knob Current value GENERAL display of the Utility mode. Making a setting here automatically changes the setting of that parameter as well. Changing the tonal qualities of the Voice Knobs 1 – 8 let you adjust a variety of parameters for the current Voice, such as effect depth, attack/release characteristics, timbre, and others. Three functions can be assigned to each Knob, alternatively selected via the Knob Function buttons. 1 Press the Knob Function 1 button (at the left of Knobs 1 – 4) and Knob Function 2 button (at the left of Knobs 5 – 8) repeatedly if necessary, so that the lamp corresponding to the desired functions lights. The KNOB FUNCTION pop-up window will appear. In the pop- Unedited value (previously stored) HINT The Edit Indicator When changing the value of the parameter, the Edit Indicator will appear on the top right corner of the LCD. This gives a quick confirmation that the current program (such as Voice and Performance) has been modified but not yet stored. To store the current edited status, execute the Store operation (below). Editing a Voice up display, the function currently assigned to the knob and the current value of the function are shown. To close the popup window, press the [EXIT] button. Knob Function 1 button Knob 1 Knob 2 Knob 3 Knob 4 “Editing” refers to the process of creating a Voice by changing the parameters that make up the Voice. This can be done in Voice Edit, a sub mode within the Voice mode. The actual parameters that are available differ depending on the Voice type. Normal Voice Edit Knob 5 Knob 6 Knob 7 Knob 8 Knob Function 2 button Functions assigned to Knobs 1 – 4 or 5 – 8 A Normal Voice (pitched musical instrument-type sounds) can consist of up to eight Elements. There are two types of Voice Edit displays: Common Edit, for editing the settings common to all eight Elements; and Element Edit, for editing individual Elements. NOTE An Element is the basic and the smallest unit for a Voice, and is Current values of the functions created by applying various parameters (Effect, EG, etc.) to the waveform of the instrument sound. Each Voice of this instrument consists of several Elements. Drum Voice Edit Unedited value (previously stored) NOTE When the “Knob FuncDispSw” is set to “off” in the Utility GENERAL display, the KNOB FUNCTION pop-up window will not be shown. 2 Turn a desired knob while playing the keyboard. The KNOB FUNCTION pop-up window will appear, and the function assigned to the knob you’re currently operating will affect the sound of the current Voice. The KNOB FUNCTION pop-up window shows the function assigned to the knob you’re currently operating, the function value, and the “Original” value. The “Original” value indicates the unedited value (previously stored value) of the function assigned to the knob. 28 MOXF6/MOXF8 Owner’s Manual There are two types of Drum Voice Edit displays: Common Edit, for editing the settings that apply to all Drum keys in the Voice; and Key Edit, for editing individual keys. Quick Guide NOTE To cancel the Store operation, press the [EXIT] button before Basic Procedure for Voice Edit 1 2 pressing the [ENTER] button. NOTICE Press the [EDIT] button in the Voice mode. Edit the current Voice. I When a Normal Voice is selected: To edit Common parameters, press the [COMMON] button. Never attempt to turn off the power while data is being written to Flash ROM (while an “Executing...” or “Please keep power on” message is shown). Turning the power off in this state results in loss of all user data and may cause the system to freeze (due to corruption of data in the Flash ROM). To edit Element parameters, press the desired Element number button from [1] – [8]. HINT I When a Drum Voice is selected: Compare function To edit Common parameters, press the [COMMON] button. The Compare function lets you switch between the just-edited Voice and its original, unedited condition, allowing you to hear how your edits affect the sound. To edit Key parameters, press the [1] button then press the desired note on the keyboard. NOTE For details about the Voice parameters, refer to the Voice I In the Voice Edit mode (with the [EDIT] lamp lit): Press the [EDIT] button so that its lamp flashes. In this status, the Voice settings prior to editing will temporarily be reinstated for comparison purposes. Press the [EDIT] button again to return to the original status. mode chapter in the Reference Manual. Common Edit display Indicates the Common Edit display. I In the Voice Store mode: Press the [EDIT] button so that its lamp flashes. In this status, you can hear the sound of the Voice at the storing destination. Press the [EDIT] button again to return to the original status. Element Edit display Indicates the display for editing Element 1. Enhancing the sound with Effects This instrument features a wide variety of Effects, letting you add reverb and chorus processing to the selected Voice for your keyboard performance. Simply changing the Effect type applied to the preset Voice lets you instantly come up with different sounds. The instructions below explain how to set the Effect type and the related parameters applied to the Preset Voice then store the settings as a User Voice. Key Edit display Indicates the Key Edit display. 1 In the Voice Play display, select a Voice then press the [F6] EFFECT button. The EFFECT display of Voice Common Edit appears. Select a Key here. 3 Assign the name to the edited Voice. On the display called via [COMMON]  [F1] GENERAL  [SF1] NAME, enter the desired name. 4 Store your edits as a User Voice. Press the [STORE] button to call up the Store display. Set the destination memory then press the [ENTER] button to execute the Store operation. Select the Effect Category and Type of Insertion Effect A. Move the cursor to the corresponding position as shown below then use the [INC]/[DEC] buttons or [DATA] dial. Store display Destination Destination Voice Bank number 2 Insertion Effect A Category Insertion Effect A Type Destination Voice name The current parameter and its value MOXF6/MOXF8 Owner’s Manual 29 Quick Guide 3 4 Select the Effect Category and Type of Insertion Effect B with the same instruction as step 2. Select the Effect connection of Insertion A and B. Move the cursor to the position shown below then use the [INC]/[DEC] buttons or [DATA] dial. Insertion Effect connection HINT You can use the following operation to simultaneously adjust the volume of Elements 1 – 8 together: 1 Press the Knob Function 1 button (at the left of Knobs 1 – 4) and Knob Function 2 button (at the left of Knobs 5 – 8) simultaneously. The six lamps light and the KNOB FUNCTION pop-up window will appear. 2 Turn one of the knobs to adjust the Element volume. 3 After completing editing, press the [EXIT] button to return to the Voice Play display. Knob Function 1 button 5 Set the output destination of each Element/Key. Knob 1 Knob 2 Knob 3 Knob 4 Knob 5 Knob 6 Knob 7 Knob 8 Move the cursor to “EL:OUT” (for the Normal Voice) or “KEY:OUT” (For the Drum Voice) then use the [INC]/[DEC] buttons or [DATA] dial. Element Out 1 – 8 Knob Function 2 button 6 If necessary, edit the Effect parameters on the display called up via the [SF2] INS A/[SF3] INS B buttons. Try narrowing in on your desired sound by finely editing the parameters provided for each Effect Type. HINT Using Controllers 7 30 After setting the parameters, press the [STORE] button to store your settings as a User Voice. MOXF6/MOXF8 Owner’s Manual Multiple controllers are assigned to each preset Voice, allowing you to apply various changes and effects to the Voice in real time. For convenience, abbreviations of the important or characteristic controllers for that Voice are shown following the Voice name in the display. However, some Voices may have indications for controllers that are not actually available on the instrument itself. These can be used, though, by transmitting the corresponding MIDI control number from an internal sequencer, an external sequencer, or an external MIDI controller. Controller Indication Controller Name MIDI Control Number (default setting) AS1 ASSIGN 1 knob 16 AS2 ASSIGN 2 knob 17 AF1 ASSIGNABLE FUNCTION [1] button 86 AF2 ASSIGNABLE FUNCTION [2] button 87 FC1 Foot Controller 11 FC2 not included on panel 4 MW Modulation Wheel 1 RB not included on panel 22 Quick Guide Changing the Arpeggio Type assignment Try changing the Arpeggio Types assigned to the [SF1] – [SF6] buttons of the Preset Voice. 1 Press the ARP [EDIT] button. The Arpeggio Edit display appears. 2 Press the desired Arpeggio button, [SF1] ARP1 – [SF6] ARP6. 3 Press the [F2] TYPE button to call up the TYPE display. 4 Select the desired Arpeggio Type you want to assign. Creating a new Performance by using your favorite Voice (Performance Creator) A program in which multiple Voices (parts) are combined in a layer, or in other configurations is referred to as a “Performance.” Each Performance can contain up to four different parts (Voices). This instrument features a convenient Performance Creator function which lets you create a new Performance by using favorite Voices you’ve found in the Voice mode. This function lets you copy parameter settings associated with the Voice (such as Effects) to the Performance—allowing you to quickly and easily come up with precisely the sound you want. Performance Creator provides three convenient features: Layer, Split, and Drum Assign. Edit the “Bank,” “Category,” “SubCategory,” and “Type” by using the [DATA] dial. 5 Edit the other parameters if necessary. 6 Turn on the ARP [ON/OFF] button then play the keyboard. Layer—Playing different Voices together This section explains how to create a Performance in which different Voices are layered together across the keyboard. By creating such a Performance, you can play a rich, thick sound of a layered piano and strings, for example. HINT Copying the Arpeggio Type to another button 1 Select a Voice in the Voice mode. 2 Press the [LAYER] button on the panel. To copy the ARP 1 button’s Arpeggio Type to one of the ARP 2 – 6 buttons, hold the [STORE] button and press the desired button, [SF2] – [SF6], in the Arpeggio Edit display. The Category Search display appears. 3 Select the Category including the Voice you want to layer then press the Cursor [>] button. The Voice list is shown. MOXF6/MOXF8 Owner’s Manual 31 Quick Guide 4 Select the desired Voice from the list, then press the [ENTER] button. 2 Press the [SPLIT] button on the panel. The Category Search display appears. The Performance Play display will appear. The Voice selected in the Voice mode will be assigned to 3 Part 1, and the Voice selected after pressing the [LAYER] Move the cursor to “SPLITPOINT” then set the Split Point. button will be assigned to Part 2. These two Voices are sounded simultaneously in a layer as a “Performance.” You can confirm what Voices are layered on the display called up via the [F2] VOICE button. You can determine the Split Point by holding the [SHIFT] button then pressing the desired note on the keyboard. NOTE The note set to the Split Point is included in the upper section of the keyboard. 5 Press the [STORE] button to store the settings as a Performance. 4 Move the cursor to “LO/UP” then select whether the desired Voice is assigned to the lower section or the upper section of the keyboard. NOTE When you press the [EDIT] button in the Store display, you can check the sound of the Performance at the storing destination. Split—Playing two different Voices with your left and right hands This section shows you how to create a Performance in which the keyboard is divided (or split) into two sections—the lefthand section and the right-hand. The lowest note of the righthand section is referred to as the “Split Point.” By creating such a Performance, you can play a bass part with your left hand, and a piano part with your right hand, for example. NOTE When the original Voice is a Drum Voice, Split is not applied to the part assigned the Drum Voice. In this case, only the desired Voice is assigned to the keyboard range according to the “SPLITPOINT” and “LO/UP” settings. 5 Move the cursor to “Main”/“Sub” then select the Category that includes your desired Voice. 6 Press the Cursor [>] button. The Voice list is shown. 1 32 Select a Voice in the Voice mode. MOXF6/MOXF8 Owner’s Manual Quick Guide 7 Select the desired Voice from the list, then press the [ENTER] button. 3 Press the Cursor [>] button. The Voice list is shown. The Performance Play display will appear. The Voice selected in the Voice mode will be assigned to 4 Part 1, and the Voice selected after pressing the [SPLIT] Select the desired Drum Voice from the list, then press the [ENTER] button. button will be assigned to Part 2. These two Voices are The Performance Play display will appear. sounded in different areas of the divided keyboard as a “Performance.” You can confirm what Voices are assigned on the display called up via the [F2] VOICE button. NOTE To stop Arpeggio playback, press the ARP [ON/OFF] button so that its lamp is turned off. To start or enable Arpeggio playback again, press the ARP [ON/OFF] button so that its lamp lights. 8 Press the [STORE] button to store the settings as a Performance. Drum Assign—Layering a drum Part with the current Voice This section explains how to create a Performance in which you can trigger a drum pattern (via the Arpeggio function) in addition to the current Voice. 1 Changing the drum pattern (Arpeggio Type) Executing the Drum Assign function will assign a Drum Voice to Part 4 and set the Arpeggio of Part 4 to on. If you want to change the drum pattern, select a different Arpeggio Type in the Arpeggio Edit of the Performance mode. 5 Press the ARP [EDIT] button in the Performance Play display. The Arpeggio Edit display appears. Select a Voice in the Voice mode. 6 Press the [F2] TYPE button then the Number [4] button. The TYPE display for Part 4 appears. 2 Press the [DRUM ASSIGN] button on the panel. The Category Search display appears. Drum/Percussion is automatically assigned as the Category. The Drum Voice is assigned to Part 4 then the Arpeggio is automatically turned 7 Select the Arpeggio Type with “Bank,” “Category,” “Sub Category” and “Type.” 8 Press the [PERFORM] button to return to the Performance Play display. 9 Press the [STORE] button to store the edited Performance. on. Play the keyboard to trigger the Arpeggio. MOXF6/MOXF8 Owner’s Manual 33 Quick Guide Playing the keyboard in the Performance Mode A program in which multiple Voices (parts) are combined in a layer, or in other configurations is referred to as a “Performance.” This instrument contains 128 Performances in each of the User Banks 1 – 2 and you can play them by pressing the [PERFORM] button. Soloing a specific Part The Solo function is the opposite of Mute, and lets you instantly solo a specific Part and mute all others. 2 1 Selecting a Performance 1 Selecting a Performance is done in basically the same way as selecting a Voice (see page 25). As in the Voice Play mode, you can use the Category Search (page 26) and Favorite Category (page 26) functions in the Performance Play mode. Press the [SOLO] button. The SOLO lamp lights, indicating that Solo is enabled. 2 Press any of the Number [1] – [4] buttons. The lamp of the pressed button will flash and only the corresponding Part will be sounded. Press any other Number button to change the solo Part. NOTE You can exit from this status by pressing the [TRACK] button or [PERFORMANCE CONTROL] button. Switching a Part on/off The Performance Play mode lets you turn the four Parts of the current Performance on or off as desired. Turning specific Parts on/off (Mute function) You can turn individual Parts on/off by using the Mute function. 1 Using the Arpeggio function The Arpeggio function lets you trigger rhythm patterns, riffs and phrases using the current Voice by simply playing notes on the keyboard. In the Performance mode, each of four Arpeggio types is assigned to each of four Parts. This means four Arpeggio types can be played back simultaneously. Try selecting different Performances and check out the various Arpeggio types. NOTE For details about Arpeggio, see the “Reference Manual” PDF document. 2 1 Press the [PERFORMANCE CONTROL] button. The button lamp lights, indicating that each Part can be turned on/off. 2 Press any of the Number [9] – [12] buttons. The lamp of the pressed button will be turned off and the corresponding Part will be muted. Press the same button again to turn the lamp on and disengage the mute function for that Part. You can turn multiple Parts on/off by pressing their buttons. NOTE Parts can be muted also by pressing the [MUTE] button then the Number [1] – [4] buttons. 34 MOXF6/MOXF8 Owner’s Manual Since the preset Performances already have their own Arpeggio types pre-assigned, you can play the Arpeggio by selecting the desired Performance, turning on the ARP [ON/ OFF] button, then pressing any note. Instructions on using Arpeggio are basically the same as in the Voice mode. Quick Guide Turning Arpeggio playback on/off for each Part You can turn Arpeggio playback on or off for each Part of the Performance as described below. 2 1 Changing the timbre of the Voice Just as in the Voice mode, the sound of the Performance (consisting of a maximum of four Parts or Voices) can be edited via the Knobs in the Performance mode. There are two ways to edit the Performance: editing the entire Performance, and editing only one specific Part (Voice) assigned to the Performance. I To edit the entire Performance: Turn the Knob in the Performance Play mode (called up via only the [PERFORM] button) or Performance Common Edit mode (called up via [PERFORM]  [EDIT]  [COMMON]). 1 Press the [PERFORMANCE CONTROL] button. The [PERFORMANCE CONTROL] lamp lights, indicating that Arpeggio playback for each Part can be turned on/off. 2 Pressing each of the Number [5] – [8] buttons toggles Arpeggio playback on and off for each Part. I To edit a specific Voice of the current Performance: Turn the Knob in the Performance Part Edit mode (called up via [PERFORM]  [EDIT]  [1] – [4]). Knob 1 Knob 2 Knob 3 Knob 4 Knob 5 Knob 6 Knob 7 Knob 8 If any of the [5] – [8] lamps is turned off, the Arpeggio playback of the corresponding Part is muted. Turning the Arpeggio Hold parameter on/off for each Part You can turn the Arpeggio Hold parameter on /off or on/syncoff for each Part of the Performance as described below. When the Arpeggio Hold parameter is set to “on,” Arpeggio playback continues even if the note is released. NOTE The Arpeggio Hold parameter is in the [F3] MAIN display of the Arpeggio Edit display. For details on this parameter, see the Reference Manual. 1 2 1 Press the [PERFORMANCE CONTROL] button. The [PERFORMANCE CONTROL] lamp lights, indicating that Arpeggio Hold for each Part can be turned on/off or on/ sync-off. 2 Pressing each of the Number [13] – [16] buttons toggles the Arpeggio Hold parameter on and off for each Part. If any of the [13] – [16] lamps is turned on, the Arpeggio Hold parameter of the corresponding Part is turned on. MOXF6/MOXF8 Owner’s Manual 35 Quick Guide HINT You can use the following operation to adjust the volume and pan settings of Parts 1 – 4: 1 Press the Knob Function 1 button (at the left of Knobs 1 – 4) and Knob Function 2 button (at the left of Knobs 5 – 8) simultaneously. The six lamps light and the KNOB FUNCTION pop-up window will appear. Recording in the Performance mode While experimenting and playing around with Arpeggios in the Performance mode, you may find some rhythm patterns and phrases that you like, and you may want to store them for future recall. The best and easiest way to capture these is to record your keyboard playing to a Song or Pattern. 2 Turn the desired Knob to adjust the setting. Turning one of Knobs 1 – 4 changes the volume of Parts 1 – 4, respectively. Turning one of Knobs 5 – 8 changes the pan of Parts 1 – 4, respectively. 3 After completing editing, press the [EXIT] button to return to the Performance Play display. Song and Pattern Songs and Patterns are MIDI sequence data consisting of up to 16 Tracks. I Song Knob Function 1 button Knob 1 Knob 2 Knob 3 Knob 4 Knob 5 Knob 6 Knob 7 Knob 8 Volume for Parts 1–4 A Song on this instrument is effectively the same as a song on a MIDI sequencer, and playback automatically stops at the end of the recorded data. I Pattern Pan for Parts 1–4 Knob Function 2 button In this instrument, the term “Pattern” refers to a relatively short musical or rhythmic phrase — 1 to 256 measures — which is used for looped playback. Therefore, once Pattern playback starts, it continues until you press the [J] (Stop) button. Recording the melody and Arpeggio playback to the Song HINT You can use the following operation to adjust the pitch of Parts 1 – 4: 1 Press the [EDIT] button in the Performance mode. 2 Press the Number [1] – [4] button corresponding to the Part you wish to edit. 3 Press the [F4] TONE button. 4 Press the [SF1] TUNE button. 5 Change the NoteShift value to adjust the pitch. 6 After completing editing, press the [EXIT] button to return to the Performance Play display. 36 MOXF6/MOXF8 Owner’s Manual When a Song is selected as the destination of Performance recording, you can record your keyboard playing with the Arpeggio without having to worry about measure limits or running out of recording space. It is a good idea, for example, to record your keyboard playing, freely calling up various Arpeggio types, then editing the Song later as necessary. You may even want to keep the recorder ‘running’ as you improvise, then listen back later and pick out the best parts to create your final Song. Try recording as shown in the instructions below. 1 In the Performance Play mode, select a Performance for recording. 2 Press the ARP [ON/OFF] button so that the lamp lights. Quick Guide 3 7 “CopyPerfParam” = “on” Press the [REC] button to call up the Performance Record mode. Set this to “on” when you wish to copy the parameter settings for the Performance Parts 1 – 4 to the destination Parts of the Song. 8 “MoveToRecMode” = “on” Set this to “on” when you wish to move to the Song mode (specified via the SeqMode) after recording ends. [F5] CLICK 9 (click on) Press the [F5] button to turn the metronome on if you wish 4 to use the metronome. Set the following parameters on each of the Performance Record displays. 5 Press any note to start recording. Play the keyboard in time with the metronome. You can [F1] SETUP display change the Arpeggio type and settings by pressing any of the [SF1] – [SF6] buttons while recording. 1 2 3 4 6 Press the [J] (Stop) button to stop recording. Recording stops and the instrument enters the Song mode. After recording, the created data will be automatically stored 1 “SeqMode” = “song” to internal Song/Pattern memory. Press the [F] button to This setting lets you record your keyboard performance hear your newly recorded performance. to the Song. Record your keyboard performance to additional Tracks in 2 “Number” Song Record as desired, and edit the recorded data in the Select a destination Song. Executing Performance Song Edit or Song Job to finalize the Song data. recording overwrites and erases all the previously NOTE Regarding Arpeggios, not only the played notes but also all recorded data of the specified Song. Make sure to select note events of Arpeggio playback will be recorded. a Song which contains no data. 3 “TimeSignature” = “4/4” Set the same value here as that of the Arpeggio type. Normally, set this to “4/4.” 7 After completing, press the [STORE] button to store the Song. 4 “Tempo” Set the desired tempo of the metronome and Arpeggio for recording. Recording Arpeggio playback to a Pattern [F2] REC TR display 5 5 “RecTrack” Select the destination Tracks from “1 – 4,” “5 – 8,” “9 – 12,” and “13 – 16.” [F3] OTHER display If you record your keyboard playing along with Arpeggio playback in the Performance mode to a Pattern, you can quickly create full and complete rhythm patterns lasting just a few measures. These short Patterns of MIDI sequence data can be played back repeatedly in a loop and then conveniently used as ‘building blocks’ for your original Songs. The Performance Recording to a Pattern operation is the almost same as that of Recording to a Song, with the exception of the settings below. 6 7 8 9 6 “KeyOnStart” = “on” When set to “on,” recording starts immediately when you press any note on the keyboard. Set this parameter to “on” when using the Arpeggio. In the Performance Record display, set the “Section” and “SectionLength” as well as the same settings as in “Recording the melody and Arpeggio playback to the Song.” MOXF6/MOXF8 Owner’s Manual 37 Quick Guide Section From A – P, select the Section which comprises the Pattern. If you create several Sections, you can use them as rhythm variations within a single Song. Connecting a microphone or audio equipment Section Length Set the length of the selected Section. Set the value to 1 – 4 according to the length of the current Arpeggio types. After creating the Pattern Sections, program their playback order to create a Pattern Chain. For details, see page 49. Playing the keyboard along with the sound input from the A/D INPUT [L]/[R] jacks You can have the A/D input sound—such as your voice through a microphone, a guitar, bass, or CD player—assigned as an Audio Input Part. Various parameters such as volume, pan, and effect can be set to this Part and the sound is output together with the sound of your keyboard performance. In these example instructions, you’ll learn how to use the A/D input sound in the Voice mode. 1 Make sure to turn off the power of this instrument and set the A/D INPUT [GAIN] knob to the minimum. 2 Connect the audio equipment or the microphone to the A/D INPUT [L]/[R] jack on the rear panel. Stereo audio equipment (CD player, etc.) L R A/D INPUT [L] A/D INPUT [R] MOXF6/MOXF8 Microphone A/D INPUT [L]/[R] MOXF6/MOXF8 NOTE A standard dynamic microphone is recommended. (This instrument does not support phantom-powered condenser microphones.) 38 MOXF6/MOXF8 Owner’s Manual 3 Turn on the connected audio equipment, then turn on the MOXF6/MOXF8. 4 Press the [VOICE] button to enter the Voice Play mode. Quick Guide 5 Press [UTILITY]  [F3] VCE A/D  [SF1] OUTPUT, then set the “Mono/Stereo” parameter. 8 This parameter determines the signal configuration for the Press the [LEVEL] meter button so that the [A/D INPUT] lamp lights, then adjust the input level by using the [GAIN] knob. audio signal via the A/D INPUT [L]/[R] jacks, or how the signal NOTE Adjust the [GAIN] knob to raise the input level as far as or signals are routed (stereo or mono). possible without allowing distortion to occur. When connecting the audio device as shown in step 2, set this parameter to “stereo” or “LRMono.” When connecting [LEVEL] meter button the microphone as shown in step 2, set this parameter to “LMono.” [LEVEL] meter If necessary, set the other parameters. NOTE For details about the parameters including Mono/Stereo, see the “Reference Manual” PDF document. NOTE The above parameter settings including Mono/Stereo are 9 applied to the entire Voice mode. If necessary, press the [STORE] button to store these with the Utility settings. Play the keyboard wile you sing into the microphone or play back the audio equipment. NOTE The above parameter settings including Mono/Stereo differ depending on the selected mode. NOTE For the Performance mode, set the above parameters on the display called up via [PERFORM]  [EDIT]  [COMMON]  [F5] A/D IN  [SF1] OUTPUT. The settings will be stored for each Performance. For the Song/Pattern mode, set this parameter on the display called up via [SONG] or [PATTERN]  [MIXING]  [EDIT]  [COMMON]  [F5] A/D IN  [SF1] OUTPUT. The settings will be stored for each Song/Pattern. 6 Press [UTILITY]  [F1] GENERAL  [SF6] OTHER, then set the “Mic/Line” parameter according to the equipment connected to the A/D INPUT [L]/[R] jacks. Press the [VOICE] button, then select the desired Voice. 10 If necessary, press the [STORE] button to store the Voice. Playing the keyboard along with Vocoder connecting equipment of high output level (such as a This instrument features a Vocoder function. This is a distinctive, “robot voice” effect which extracts the characteristic of the microphone sound and adds it to the sound of your keyboard performance. In these example instructions, you’ll learn how to use the Vocoder in the Voice mode. synthesizer keyboard, CD player), set this parameter to “line.” NOTE For details about the Vocoder, see the “Reference Manual” PDF When connecting equipment of low output level (such as a microphone, guitar, bass), set this parameter to “mic.” When document. NOTE This setting is available for all modes. If necessary, press the [STORE] button to store this with the Utility settings. 7 1 Connect the microphone by following steps 1 – 8 on the previous page. 2 Press the [VOICE] button, then select the desired Voice to which the Vocoder is applied. This instrument features special Voices specifically designed for use with the Vocoder. Call up the Category Search display Press the A/D INPUT [ON/OFF] button so that its lamp lights. then select the desired Voice from the “Vocoder” Main Category. This setting enables audio signals to be input from the connected audio device. NOTE If you use the Vocoder effect in the Performance/Song/Pattern mode, assign the Voice for the Vocoder to Part 1. Vocoder cannot be applied to any of the other Parts. MOXF6/MOXF8 Owner’s Manual 39 Quick Guide 3 Press [EDIT]  [COMMON]  [F6] EFFECT  [SF1] CONNECT, then set the “InsEF Connect” parameter to “vocoder.” NOTE The “InsEF Connect” parameter is automatically set to “vocoder” if you select a Voice from the Vocoder Category in step 2. Creating an original Song This instrument features a built-in multi Track sequencer for recording your keyboard performance as MIDI data. This function by itself is enough to create full, complex multiinstrument arrangements and complete Songs. Terminology 4 Song and Pattern From the [SF2] VOCODER display, set the Vocoder related parameters if necessary. See page 36. Speak or sing into the microphone while pressing the note(s) Track to generate the machine-like Vocoder sound. Set the related parameters as desired while listening to the Vocoder sound. For details about each parameter, see the “Reference Manual” PDF document. This is a memory location on the sequencer where your musical performances (made up of MIDI events) are stored. The MOXF6/MOXF8 provides 16 Tracks, which correspond to the 16 Parts of the Mixing. Mixing This is a program in which multiple Voices are assigned to Parts for multi-timbral play in the Song and Pattern modes. Each Mixing can contain up to 16 parts and a separate Mixing can be created for each Song. 5 Press the [STORE] button to call up the Store display then store the settings as a User Voice. Realtime Recording With Realtime recording, the instrument functions in the same way as a MD recorder, recording the performance data as it is played. This allows you to capture all the nuances of an actual performance. Realtime Record features three available methods: Replace, Overdub and Punch In/Out. Replace lets you overwrite an already recorded Track with new data. Overdub lets you add more data to a Track that already contains data. Punch In/Out lets you re-record only over a specific area of the Track. Step Recording With Step recording, you can compose your performance by “writing” it down one event at a time. This is a non-realtime, step recording method — similar to writing music notation onto paper. 40 MOXF6/MOXF8 Owner’s Manual Quick Guide Song playback You have already learned how to play back Songs on page 19. In this section, you’ll learn how to use convenient mute/solo functions during playback. Creating a Drum part via Step Recording Now, try creating a Song. First, record a 4-measure drum phrase as shown below to Track 1 by using Step Recording. Track mute This lets you mute a specific Track or Tracks of the Song. 1 Press the [MUTE] button so that its lamp lights. The lamps of the Number buttons light, indicating that the corresponding Tracks are on. 1 Press the [SONG] button to call up the Song Play display then select an empty Song. 2 On the [F1] PLAY display, set the time signature to “4/4.” Time signature Number [1] – [16] buttons 2 [MUTE] button To mute a Track, press the corresponding Number [1] – [16] buttons (the lamp turns off). Multiple Tracks can be muted simultaneously. 3 To sound a muted Track, press the corresponding button (lamp is off) so that its lamp lights. 3 Press the [REC] button, followed by the [F1] SETUP button, then set the parameters as below. For future recording purposes, make sure all buttons are lit • Type = step and Mute is turned off for all Tracks. • Event = note • RecTr = 1 • Ch = all If necessary, set the tempo to the desired value. Track solo This lets you solo a specific Track of the Song. 1 Press the [SOLO] button so that its lamp lights. 4 Press the [F2] VOICE button, followed by the [CATEGORY SEARCH] button, then select the Drum Voice. Set the Main Category to “Drum/Percussion” then set the Sub Number [1] – [16] buttons 2 [SOLO] button Category to “Drums.” Move the Cursor [>] button to call up the Drum Voice List. From this list, select “PDR B09 Analog” To solo a Track, press the corresponding Number [1] – [16] buttons (the lamp flashes). then press the [ENTER] button. Press another number button to change the soloed Track. 3 Press the [TRACK] or [MUTE] button to return to the original status. MOXF6/MOXF8 Owner’s Manual 41 Quick Guide 5 6 Press the [F] (Play) button to enter the Step Record mode. 14 Press the [JOB] button, followed by the [F3] EVENT button to call up the EVENT JOB SELECT display. The [F] button lamp lights and the Step Record display To create a four-measure drum pattern (which repeats the appears. recorded drum phrase), use the Copy Event Job. Set the “Step Time” to “480.” The “Step Time” parameter determines to what position the 15 Select “02: Copy Event” then press the [ENTER] button. pointer will advance after a note has been entered. Here, the pointer will advance in quarter-note steps. 7 Press the [P] (Top) button to return to the top of the Song, then press the B0 key four times. The Bass Drum Kick sound (assigned to the B0 key) is recorded to the timing of each beat. NOTE If you are using the MOXF6, use the [OCTAVE] buttons to make sure that the Bass Drum Kick sounds when you play the B0 key. This is necessary since the MOXF6 has a shorter keyboard and doesn’t have a B0 key. 8 [ENTER] button to execute the Copy Event Job. • Source Track = “01”, Source range = “001:1:000” – “002:1:000” • Destination Track = “01”, Top measure of the destination = Press the [J] (Stop) button to stop recording. This returns to the Song Play display. 9 16 Make the settings as listed below then press the To record another percussion sound, press the [REC] button then the [F] (Play) button to enter the Step Record mode again. “002” • “NumberOfTimes” = “x 03” Executing this Job will copy the drum phrase (recorded to the first measure) to the 2nd, 3rd, and 4th measures respectively. The [F] button lamp lights and the Step Record display appears. 10 Set the “Step Time” to “ 240.” The Step Time parameter determines to what position the pointer will advance after a note has been entered. Here, the pointer will advance in eighth-note steps. 11 Press the [P] (Top) button to return to the top of the Song, then press the [F3] REST button and G 1 key four times. 17 Press in order the [SONG] button, [P] (Top) button, and [F] (Play) button to hear the recorded data. To stop playback, press the [J] (Stop) button. An eighth-note rest is recorded to each down beat and the Hi-Hat Cymbal sound (assigned to the G 1 key) is recorded to each up beat. NOTE If you are using the MOXF6, use the [OCTAVE] buttons to make sure that the Hi-Hat Cymbal sounds when you play the G 1 key. This is necessary since the MOXF6 has a shorter keyboard and doesn’t have a G 1 key. 12 Press the [J] (Stop) button to stop recording. This returns to the Song Play display. After executing the above operations (steps 1 – 12), you should now have a 1-measure drum phrase as shown below. 13 Press the [P] (Top) button, then press the [F] (Play) button to hear the recorded data. To stop playback, press the [J] (Stop) button. 42 MOXF6/MOXF8 Owner’s Manual HINT Tips in Step Recording • In Step recording, you can also enter chords. Because notes are actually entered when the keys are released, make sure to press all correct keys you want to enter then release the keys. • In Step Recording, press the [F] (Play) button to start playback from the current position. In this status, pressing the [J] (Stop) button will stop playback and return to the Step Record mode. • In Step recording, you can create the legato phrases by setting the GateTime to “100%.” • In Step Recording, you can enter tied notes. For example, first set the Step Time to “480” (quarter note) then press and release the key. Next, change the Step Time to “240” (8th note) then press the [F4] TIE button, resulting in a dotted quarter note. Quick Guide Creating a bass part via Realtime Recording Next, record the bass line via Realtime Recording to Track 2. 1 2 6 Press the [REC] button to return to the Song Record display. 7 Press the [P] (Top) button to return to the top of the Song, then press the [F] (Play) button to start recording. In the Song Play mode, select the same Song (created above) to which the Drum part has already been recorded. As soon as the lead-in count (1-measure) is finished, play the following notation. Press the [REC] button, followed by the [F1] SETUP button, then set the parameters as below. • “Type” = “replace” • “Quantize” = “240” • “RecTr” = “2” 8 After playing the above notation, press the [J] (Stop) button to stop recording. If you play any wrong notes, press the [J] (Stop) button, then try recording again. Repeat as often as necessary until you get it right. 3 Press the [F2] VOICE button, followed by the [CATEGORY SEARCH] button then select the Bass Voice. 9 Press the [P] (Top) button followed by the [F] (Play) button to hear the recorded data. The recorded data of the Tracks 1 and 2 will be played back. Set the “Main” (Main Category) to “Bass” then set the “Sub” To stop playback, press the [J] (Stop) button. If you are not (Sub Category) to “Synth Bass.” Move the Cursor [>] button satisfied with the recorded data, try this operation again. to call up the Voice List. From this list, select “PRE3 E01 Uni Punch” then press the [ENTER] button. HINT Re-recording a specific part of a Song (Punch In/Out) Use the Punch In/Out recording method to record over only a specific portion of the Track. If you set the start point (Punch In) and end point (Punch Out), and then start recording from the top of the Song, the actual recording will be done only between the Punch In and Punch Out points. In the eight-measure example below, only the third through the fifth measures are rerecorded. Before re-recording 4 Press the [F5] CLICK button to turn the Click ( ) on. 5 Press [UTILITY]  [F2] SEQ  [SF1] CLICK, then set the Click related parameters as below. • “Mode” = “rec” • “Beat” = “04” 1 Recording start Recording stop Punch In point Punch Out point 2 3 4 5 6 7 8 4 5 6 7 8 After re-recording 1 2 3 Newly recorded data • “RecCount” = “1meas” NOTE Punch In/Out Recording can only be used with Realtime recording. NOTE Note that the Punch In/Out method always replaces (destroys) the original data over the specified area. With this setting, there will be a one-measure lead-in count before recording begins and the Click will play back only while recording. To execute Punch In/Punch Out recording in the above condition, set the following parameters beforehand on the [F1] SETUP display in the Song Record mode. • “Type” = “punch” • Punch In = 003:01 • Punch Out = 006:01 MOXF6/MOXF8 Owner’s Manual 43 Quick Guide Punch In point Playback of the recording Track is turned off from this point, and your keyboard performance will be recorded to the Track. 3 Press the [REC] button, followed by the [F1] SETUP button, then set the parameters as below. • “Type” = “replace” • “Quantize” = “off” • “RecTr” = “3” 4 Punch Out point Recording ends at this point and normal playback of the recording Track starts. Press the [F2] VOICE button, followed by the [CATEGORY SEARCH] button then select the Synthesizer Voice. Set the Main Category to “Synth Pad / Choir” then set the Sub Category to “Analog.” Move the Cursor [>] button to call [SF1] COPYLOC button Press the [SF1] COPY LOC to assign the measure numbers registered to the Locations (Loc1 and Loc2) to the Punch In and Punch Out points. up the Voice List. From this list, select “PRE5 H04 Saw Pad” then press the [ENTER] button. NOTE For instructions on using the Location settings, see the “Reference Manual” PDF document. HINT Rehearsing function while recording During Realtime Recording in the Song/Pattern mode, pressing the [REC] button will call up the “Rehearsal” mode. In this mode, the [REC] indicator will flash and playback will continue uninterrupted; however, no data will be recorded, letting you practice a part or try out various ideas (while listening to the other tracks) without actually recording. To return to the Record mode, press the [REC] button again—the [REC] indicator will light continuously. Recording 5 Press ARP [EDIT] or [F3] ARP ED  [F3] MAIN, then set the Switch parameter to “on” and set the “VoiceWithARP” parameter to “off.” With the “Switch” parameter “on,” the Arpeggio of Track 3 Rehearsal mode (playback continues) can be played back. If the “VoiceWithARP” parameter is set to “on,” selecting the Arpeggio Type will change the Voice from the one selected in step 4. This is why you should set the “VoiceWithARP” parameter to “off” here. 6 Creating a synthesizer part by using Arpeggio Press [F2] TYPE  [SF1] ARP1, then assign the Arpeggio Type to the [SF1] ARP1 button. On this display, set the parameters as below: • “Bank” = “Pre” • “Category” = “Seq” Next, record Arpeggio playback via Realtime Recording to Track 3. 44 1 In the Song Play mode, select the same Song to which the Drum and Bass parts have already been recorded. 2 Press the ARP [ON/OFF] button so that its lamp lights. MOXF6/MOXF8 Owner’s Manual • “SubCategory” = “Genrl” • “Type” = “7483” If desired, assign different Arpeggio Types to the [SF2] – [SF6] buttons. Quick Guide 7 Press the [REC] button to return to the Song Record display. 8 Press the [P] (Top) button to move to the top of the Song then press the [F] (Play) button to start recording. The [F] (Play) button lamp lights and “RECORDING” NOTE The Song location at which you edit or input the event is indicated by measure, beat and clock. A quarter note (one beat when the time signature is set to “4/4”) consists of 480 divisions. The length of each note (gate time) is indicated by Beat and Clock. For example, 001:000 is equivalent to a quarter note and 000:240 is equivalent to an eighth note. 3 appears at the top of the display, indicating that the Recording has already started. After the one-measure lead- Use the Cursor buttons to move the cursor to the location to be edited, then turn the [DATA] dial to edit the value. When you change the value at the current line, the entire line in count is finished, play the following notation. starts flashing. 4 The edited event line stops flashing. NOTE All the notes generated via Arpeggio playback will be recorded. 9 Before moving the cursor to another line, press the [ENTER] button to fix the value. 5 As necessary, correct the other data. After playing the above notation, press the [J] (Stop) button to stop recording. If you find unnecessary notes (not described on the notation), If you play any wrong notes, press the [J] (Stop) button, the [F6] DELETE button. move the cursor to the corresponding position then press then try recording again. Repeat as often as necessary until 6 you get it right. 10 Press the [P] (Top) button, followed by the [F] After completing editing, press the [EXIT] button to return to the Song Play display. To confirm the recorded data, press the [P] (Top) button, (Play) button to hear the recorded data. followed by the [F] (Play) button to start playback. To stop The recorded data of Tracks 1, 2 and 3 will be played back. playback, press the [J] button. To stop playback, press the [J] (Stop) button. If you are not satisfied with the recorded data, try this operation again. Correcting wrong notes If you’ve played any wrong notes while recording and wish to correct them, press the [EDIT] button from the Song Play mode to go to the Song Edit mode. Song Edit lets you clean up and edit data of already recorded Songs or insert new data to the Songs. Check for any mistakenly recorded or wrong events on the event list display of the Song Edit mode, then correct them as needed. 1 With the recorded Song selected, press the [EDIT] button to enter Song Edit, then press the [F1] CHANGE button. The CHANGE display appears. Completing the Song by editing the Mixing In this final step (other than storing your precious work, which we’ll cover next), you can mix down your Tracks with the Song Mixing function – adjusting the volume balance and pan setting of all the parts and tweaking the effect levels. NOTE The explanations here also apply to the Pattern mode. 1 Press the [SONG] button to enter the Song Play mode, then select the desired Song. 2 Press the [MIXING] button to enter the Mixing mode, then set various parameters. The [MIXING] button lamp lights and the Mixing display will 2 Press the desired Track number button (from [1] – [3]). The list of the MIDI events recorded to the selected Track in the previous section appears on the display. Location Notes Gate time appear. Select the menu you wish to edit by pressing the [F1] – [F4] buttons, then edit the parameters in each display. Mixing Play display Indicates that the Mixing parameter is modified but not stored yet. Velocity For details about each parameter, see the “Reference Manual” PDF document. MOXF6/MOXF8 Owner’s Manual 45 Quick Guide 3 Press the [EDIT] button to enter the Mixing Edit mode. 2 Select “04:Song Name,” press the [ENTER] button to call up the Song Name display, then enter the Song name. Move the Cursor to the desired position then enter the character by holding the [SF6] CHAR button. Repeat this operation as often as necessary to create the name. 4 Call up the Common Edit display or Part Edit display. Use Part Edit to edit the parameters for each Part. Use Common Edit to edit the parameters for all of the Parts. 5 Select the menu you wish to edit by pressing the [F1] – [F6] buttons and [SF1] – [SF6] buttons, then edit the parameters in each display. For details on each parameter, see the “Reference Manual” NOTE For specific instructions on naming, see Basic Operation on page 22. 3 After naming, press the [ENTER] button to actually enter the name. 4 Press the [STORE] button, followed by the [F1] SEQ button. PDF document. 6 Repeat steps 4 – 5 as desired. 7 Press [STORE]  [F1] SEQ  [ENTER] to store the settings as Song data. This operation will store all the Songs and Patterns at the same time. NOTICE If you are editing Mixing parameters and you select a different Song without storing the one being edited, all the edits you've made will be erased. HINT The Store display appears. Storing Mixing settings as a template The Mixing settings you make can be stored as a Template—letting you create your own custom Mixing/Voice configurations for future use in recording Songs. This operation can be done on the display called up via [SONG]  [STORE]  [F2] TEMPLATE. For detailed instructions, see the “Reference Manual” PDF document. 5 Press the [ENTER] button to store the Song. This operation will store all the Songs and Patterns at the same time. Storing the created Song After storing, press the [EXIT] button to exit from the Store display. After creating a Song, assign a name to the Song then execute the Store operation. 1 46 Press [SONG]  [JOB]  [F6] SONG to call up the Song Job List. MOXF6/MOXF8 Owner’s Manual NOTE Song/Pattern data consists of MIDI sequence data and Mixing data. MIDI sequence data is recorded by playing the keyboard while Mixing data is created by editing the parameters. Quick Guide Creating an original Pattern The Pattern mode also lets you record your rhythm patterns or riffs to the different Sections as you wish—and as the inspiration hits—then combine the Sections into a Pattern Chain to create a complete Song. Along with the Arpeggio feature and Performance recording, you have a wide range of easy-to-use tools to quickly create fully arranged, professional sounding Songs. 1st measure Intro Section A Melody A Section B Melody B Section C Main theme Section D Melody B Section E Main theme Section F 120th measure Ending Creating a Pattern (Section A) by using Arpeggio In addition to creating a Pattern by recording your keyboard performance conventionally, you can also use the powerful Arpeggio playback features of this instrument. Here, create data for Section A by recording Arpeggio playback to Track 1 as the drum part, Track 2 as the guitar part and Track 3 as the bass part. 1 Press the [PATTERN] button to enter Pattern Play then select a Pattern. 2 Press the [PATTERN SECTION] so that its lamp lights then press the Number [1] button to select Section A. 3 On the Pattern Play display, set the Pattern Length, Time Signature and Tempo. Section G Listening to the Demo Patterns Before creating your own original pattern, you should give a listen to some of the preset Demo Patterns. These specially recorded Patterns cover a wide range of musical genres and are full of great hints and ideas on how you can create and use Patterns in your own music. 1 Time Signature Tempo Length 4 Press the [TRACK] so that its lamp lights then press the Number [1] button to select Track 1. 5 Press ARP [EDIT]  [F3] MAIN, then set the “Switch” parameter to “on” and set the “VoiceWithARP” parameter to “on.” Press the [PATTERN] button to enter the Pattern mode. With the “Switch” parameter “on,” the Arpeggio of Track 1 The Pattern Play display will appear. can be played back. When the Arpeggio Type is selected with the “VoiceWithARP” parameter “on,” the Voice 2 Select a Pattern by turning the [DATA] dial. 3 Press the [F] (Play) button to start playback of the Pattern. appropriate for the selected Arpeggio Type will be automatically called up. The Pattern will play back repeatedly until you press the [J] (Stop) button. 4 Press the [PATTERN SECTION] button then change Sections, selecting from A – P. Pressing the [1] – [8] buttons calls up Sections A – H and pressing the [9] – [16] buttons calls up Sections I – P. Section A – H 6 Press the ARP [ON/OFF] button so that its lamp lights. [PATTERN SECTION] button Section I – P NOTE By changing the Sections, you can create rhythmic variations, and easily improvise arrangements (such as intro, verse, chorus, verse, chorus, ending) in real time. MOXF6/MOXF8 Owner’s Manual 47 Quick Guide 7 Press the [F2] TYPE button then select the desired Arpeggio Type assigned to the [SF1] – [SF6] buttons. 13 Press [STORE]  [F1] SEQ  [ENTER] to store the recorded Phrases as a Pattern. This operation will store all the Song/Patterns. Now that you’ve recorded Section A, go on to the following instructions and create Section B by using the Pattern Copy Job with the already recorded User Phrases. Changing the Arpeggio Type will call up a different Voice since the “VoiceWithARP” parameter is set to “on.” If you want to record a drum pattern, for example, set the Category to a drum/percussion-like name then find the desired Arpeggio Creating another Pattern (Section B) by using already recorded data Type. 8 Press the [REC] button then set the parameters for recording on the [F1] SETUP display as below. • “Type” = “replace” Here, you’ll learn how to create a Section B by using recorded data copied from Section A. For example, the drum part and bass part will be copied from Section A, and the guitar part will be created via the same note data as that of the bass part. • “Loop” = “off” • “Quantize” = “off” Copying the Pattern data Set the other parameters if necessary. First, copy all the recorded data from the Section A to Section B by using the Pattern Copy Job. 9 Press the [F5] CLICK button to set the click to on ( ). 1 Press [PATTERN]  [JOB] to enter the Pattern Job. 2 Press the [F6] PATTERN button, select “01: Copy Pattern” then press the [ENTER] button. The Copy Pattern Job display appears. 10 Press the [F] (Play) button to start recording. Play the keyboard to trigger Arpeggio playback. Since the “Loop” parameter is set to “off,” recording will be finished automatically when the end of the Pattern Length is reached. NOTE All the notes generated via Arpeggio playback will be recorded. 3 Select the Pattern number and Section to be copied. For the copy source, select the Pattern number and Section Recorded Data as a User Phrase which you have already recorded in the previous section. The MIDI note sequence data (except for the Voice setting, etc.) recorded in the Pattern mode will be stored as a User Phrase. The stored User Phrase can be assigned to a different Section/Track from the [F4] PATCH display in the Pattern Play mode. This allows you to use already recorded User Phrases for the other different Sections/Tracks. A single Pattern provides memory space for 256 of your own original User Phrases. For the copy destination, select the same Pattern number and “Section B.” 11 Press the [F] (Play) button to hear the recorded Source Destination Phrase. 12 Record Phrases to the other Tracks of Section A 4 as desired using the same operation. Press the [ENTER] button to execute the Pattern Copy Job. Record a bass line to Track 2, then record guitar backing to All the data of Section A will be copied to Section B. Track 3 by repeating steps 4 – 11 above. 5 48 MOXF6/MOXF8 Owner’s Manual Press the [EXIT] button a few times to return to Pattern Play. Quick Guide 6 Press the [PATTERN SECTION] button so that its lamp lights then press the Number [2] button. 9 Press the [F] (Play) button to hear the recorded Phrase. Section B is now selected. Press the [F] (Play) button to If necessary, adjust the octave setting or velocity setting of hear Section B and confirm that the Section B data has been the guitar part by using the [F2] NOTE Jobs. For details copied from Section A. about the available parameters, see the “Reference Manual” PDF document. Assign the already recorded data (User Phrase) Have the guitar and bass play together by using the user phrase of the bass recorded in Section A. NOTICE If a specific Phrase is assigned to various Sections/Tracks, keep in mind that editing the Phrase will change the playback sound of all Sections/Tracks that use this Phrase. 10 Press [STORE]  [F1] SEQ  [ENTER] to store the recorded Phrases as a Pattern. This operation will store all the Song/Patterns. 7 Press the [F4] PATCH button to call up the PATCH display. The amount of measures Phrase number 8 To Track 3 (guitar part), assign the same Phrase as that of Track 2 (bass part). This operation will have the guitar (Track 3) and bass (Track 2) play the same Phrase in unison. Assign the same Phrase as that of Track 2. After recording Section B, create other Sections as desired. As in the Song mode, you can also use Step Recording to create Patterns. Creating a Pattern Chain for converting to a Song In these instructions you’ll learn how to assign each of the created Pattern Phrases to the Section, arrange the Sections in your favorite order to create the Pattern Chain, and convert the Pattern Chain to a Song. This converted Song data can be used as backing accompaniment for melody recording. Pattern Chain Change the Sections as desired to create the Song you have in mind… Section A Section B Section F Section H ....... Song HINT Pattern Patch display On the Pattern Patch display, only the User Phrase contained in the current Pattern can be assigned to any Track. If you wish to use Phrases belonging to other Patterns, follow the instructions below: 1 Press the [SF6] COPY button. 2 Select the desired Phrase as the copy source. 3 Select the User Phrase number and Track number as the copy destination. Creating a Pattern Chain This section explains how to create a Pattern Chain by arranging the Sections in order as shown in the example above. 1 In the PLAY display of the Pattern Play mode, select the Pattern created in the previous section. 2 Press the [F6] CHAIN button. 4 Press the [ENTER] button to execute the Copy operation. MOXF6/MOXF8 Owner’s Manual 49 Quick Guide 3 desired Number buttons. The change timing of the on/off Press the [REC] button to enter the Pattern Chain Record mode then set the Recording Track and Pattern tempo. status will be recorded in real time to the Scene Track. Three Pattern Chain Track types are available. The Tempo Editing the Pattern Chain Track lets you record tempo changes for the Chain, and the Scene Track lets you record Track on/off changes. The Pattern (“patt”) Track lets you record Section changes at the desired measure points in the Song. Here, set “RecTrack” to “patt.” 4 The Pattern Chain Edit mode makes it possible to edit the order of the Sections in a chain as well as inserting tempo, and scene/mute event data. 1 In the Pattern Play mode, select the Pattern created in the previous section. 2 Press [F6] CHAIN  [EDIT] to enter the Pattern Chain mode, then edit each of the Tracks. Press the [F] (Play) button to start recording then play the Pattern. To select each Track, press the [F4] TR SEL button. Change the Sections as desired. You can “play” the Section Pattern Track Edit buttons as the Pattern plays back to create a new Song. [F4] button Scene Track Edit Section A – H [F4] button Tempo Track Edit Section I – P 5 Press the [J] (Stop) button to stop recording. The instrument returns to the CHAIN display of Pattern Play. 6 7 Press the [F] (Play) button to play the recorded Pattern Chain. Press [STORE]  [F1] SEQ  [ENTER] to store the recorded Pattern Chain. This operation will store all the Song/Patterns. 8 3 Press the [EXIT] button to return to the Pattern Play display then press the [F] (Play) button to start the Pattern Chain. 4 Press [STORE]  [F1] SEQ  [ENTER] to store the recorded Pattern Chain. This operation will store all the Song/Patterns. After pressing the [EXIT] button, record the Tempo Track then Scene Track by repeating steps 3 – 7 above. Converting a Pattern Chain to a Song IWhen you record the Tempo Track: In step 3, set the RecTrack to “tempo.” In step 4, move the cursor to the tempo column ( ) then change the tempo as 1 In Pattern Play, select the Pattern created in the previous section. 2 Press [F6] CHAIN  [EDIT] to enter the Pattern Chain mode. desired by using the [DATA] dial or [INC]/[DEC] buttons. Tempo change timing will be recorded in real time to the Tempo Track. IWhen you record the Scene Track: In Step 3, set the RecTrack to “scene.” In step 4, press the [MUTE] button so that its lamp lights then turn on/off the 50 MOXF6/MOXF8 Owner’s Manual Quick Guide 3 Press the [F3] Song button to call up the “Convert to Song” display, then select an empty Song and the top measure for the destination. For the destination, select the Song and the top measure. If the “without PC” is checkmarked, executing this operation will ignore the Program Change events in the Pattern data. 4 Press the [ENTER] button to execute the conversion. The Pattern Chain data will be converted to Song data, and Connecting external MIDI instruments With a standard MIDI cable (available separately), you can connect an external MIDI instrument, and control it from the MOXF6/MOXF8. Likewise, you can use an external MIDI device (such as a keyboard or sequencer) to control the sounds on the MOXF6/MOXF8. Below are several different MIDI connection examples; use the one most similar to your intended setup. NOTE Any one of these interfaces can be used for MIDI data transmission/reception: the MIDI connectors, or the USB [TO HOST] connector. However, they cannot be used at the same time. Select which connector is to be used for MIDI data transfer in the “MIDI IN/OUT” parameter of the [UTILTITY]  [F6] MIDI  [SF4] OTHER display. As you work through the explanations in this chapter, set “MIDI IN/OUT” to “MIDI” since MIDI is used as the example connection here. the converted data will be copied to the top measure specified in step 3. NOTICE This operation overwrites any data already existing at the destination Song. Controlling MOXF6/MOXF8 from an external MIDI keyboard or synthesizer 5 Press the [SONG] button, select the Song specified in step 3, then press the [F] (Play) button to hear the newly created Song data. Use an external keyboard or synthesizer to remotely select and play the Voices of the MOXF6/MOXF8. 6 Press [STORE]  [F1] SEQ  [ENTER] to store the created Song. MIDI [IN] This operation will store all the Song/Patterns. MOXF6/MOXF8 MIDI [OUT] External MIDI keyboard such as an 88-key synthesizer MOXF6/MOXF8 Owner’s Manual 51 Quick Guide HINT HINT MIDI Transmit Channel and Receive Channel. Make sure to match the MIDI Transmit Channel of the external MIDI instrument with the MIDI Receive Channel of the MOXF6/ MOXF8. For details on setting the MIDI Transmit Channel of the external MIDI instrument, refer to the owner’s manual of that instrument. For details on setting the MIDI Receive Channel of the MOXF6/MOXF8, check the following points. In the Voice mode/Performance mode (using the MOXF6/ MOXF8 as a single timbre tone generator): Check the MIDI Basic Receive Channel with the following operation: [UTILITY]  [F6] MIDI  [SF1] CH (channel)  “BasicRcvCh.” If necessary, change this parameter to the same number as the MIDI Transmit Channel of the external MIDI instrument. In the Song mode/Pattern mode (using the MOXF6/MOXF8 as a multi-timbral tone generator): Check the MIDI Receive Channel for each Part of the Multi with the following operation. [SONG]/[PATTERN]  [MIXING]  [EDIT]  selection parts  [F1] VOICE  [SF2] MODE  “ReceiveCh.” If necessary, change this parameter to the same number as the MIDI Transmit Channel of the external MIDI instrument. Please note that all parts whose MIDI Receive Channels are the same as the MIDI Transmit Channel of the external MIDI instrument are sounded by your keyboard performance. Change the settings of the desired parts to match the MIDI Transmit Channel settings on the external MIDI instrument. Controlling an external MIDI keyboard or synthesizer from the MOXF6/MOXF8 This connection lets you sound an external MIDI tone generator (synthesizer, tone generator module, etc.) by playing the MOXF6/MOXF8 or playing back the Song/Pattern of the MOXF6/MOXF8. Use this connection when you wish to sound the other instrument as well as the MOXF6/MOXF8. MIDI [OUT] MOXF6/MOXF8 MIDI [IN] External MIDI tone generator such as MOTIF-RACK XS 52 MOXF6/MOXF8 Owner’s Manual Splitting the sound between the MOXF6/MOXF8 and an external tone generator by MIDI channel Using the connection example shown above, you can play both instruments and have them separately sound different parts— for example, having your keyboard performance sound the external instrument while the Song/Pattern plays the sounds of the MOXF6/MOXF8. To use this feature, you must set the MOXF6/MOXF8’s output channel and the external tone generator’s receive channel to the same channel number. Check the following points after turning the power on. When playing the keyboard in the Voice mode or Performance mode: Check the MIDI transmit channel with the following operation: [UTILITY]  [F6] MIDI  [SF1] CH (channel)  “KBDTransCh.” If necessary, change this parameter to the same number as the MIDI Receive Channel of the external MIDI instrument. In the Voice play or Performance play, pressing the [TRACK] button (so that the lamp lights) can also change the MIDI Transmit Channel of the MOXF6/MOXF8. When you wish to sound only the external tone generator, set the [Master Volume] control to “0” or set Local Control to “off” with the following operation: [UTILITY]  [F6] MIDI  [SF2] SWITCH  “LocalCtrl” = “off.” For information on how to set the MIDI Receive Channel of the external MIDI instrument, refer to the owner’s manual of the external MIDI instrument. When playing back a Song/Pattern or playing the keyboard in the Song mode or Pattern mode: Check the MIDI transmit channel for each Track with the following operation: [SONG]/[PATTERN]  [F3] TRACK  [SF1] CHANNEL  “OUT CH.” If necessary, change this parameter to the same number as the MIDI Receive Channel of the external MIDI instrument. Alternately, you can set the output destination (Internal or external MIDI tone generator) for each Track from the following display: [SONG]/[PATTERN]  [F3] TRACK  [SF2] OUT SW. In this case, you’ll need to set the external MIDI tone generator to multi-timbral operation and set the MIDI Receive Channel for each part. For details, see the owner’s manual of the external MIDI tone generator. Alternately, you can have your keyboard performance split and assigned to different MIDI channels by using the Zone settings in the Master mode (page 57). Quick Guide Using a Connected Computer 3 Press the [UTILITY] button to call up the Utility mode, then press the [F6] MIDI button followed by the [SF4] OTHER By connecting the MOXF6/MOXF8 to your computer via USB, you can use DAW software on the computer to create your own original songs. NOTE The acronym DAW (digital audio workstation) refers to music software for recording, editing and mixing audio and MIDI data. The main DAW applications are Cubase, Logic Pro, SONAR and Digital Performer. Though all of these can be effectively used with the MOXF6/MOXF8, we recommend using Cubase when creating songs together with the instrument. Make sure that the USB [TO HOST] terminal of this instrument is enabled. button to call up the OTHER display. Set the “MIDI IN/OUT” parameter to “USB.” 4 Set the input and output settings for audio data and MIDI data as desired to suit your personal preferences. These settings can be set in the [F5] USB I/O display and [F6] MIDI display of the Utility mode. Setting the parameters related to the Audio data and MIDI data by using the Quick By connecting this instrument to a computer, you can take advantage of the following functions and applications. Setup lets you instantly reconfigure the MOXF6/MOXF8 for different computer/sequencer related applications by calling • External tone generator for DAW software and MIDI keyboard • Remote Controller of the DAW software • Editing parameters from the computer (MOXF6/MOXF8 Editor) up specially programmed presets. In this case, press the [QUICK SETUP] button and then set the “SETUP.” After making the settings, press the [ENTER] button to apply them to the MOXF6/MOXF8. NOTE For details on the parameters set by the Quick Setup function, see the “Reference Manual” PDF document. Connecting to a computer A USB cable and the Yamaha Steinberg USB Driver are necessary to connect the MOXF6/MOXF8 to the computer. Follow the instructions below. Note that both audio data and MIDI data can be transmitted through a USB cable. 1 Download the latest Yamaha Steinberg USB Driver from our website. After clicking the Download button, extract the compressed file. http://download.yamaha.com/ NOTE Information on system requirements is also available at the above web site. Press the [STORE] button to store the settings to internal memory. Precautions when using the USB [TO HOST] terminal When connecting the computer to the USB [TO HOST] terminal, make sure to observe the following points. Failing to do so risks freezing the computer and corrupting or losing the data. If the computer or the instrument freezes, restart the application software or the computer OS, or turn the power to the instrument off then on again. NOTICE • Use an AB type USB cable. USB 3.0 cables cannot be used. NOTE The Yamaha Steinberg USB Driver may be revised and updated without prior notice. Make sure to check and download the latest version from the above site. 2 5 Install the Yamaha Steinberg USB Driver to the computer. For instructions on installing, refer to the online Installation Guide included in the downloaded file package. When connecting this instrument to a computer, connect the USB cable to the USB TO HOST of this instrument and the USB terminal of the computer as shown below. USB [TO HOST] terminal USB terminal • Before connecting the computer to the USB [TO HOST] terminal, exit from any power-saving mode of the computer (such as suspend, sleep, standby). • Before turning on the power to the instrument, connect the computer to the USB [TO HOST] terminal. • Execute the following before turning the power to the instrument on/off or plugging/unplugging the USB cable to/ from the USB [TO HOST] terminal. • Quit any open application software on the computer. • Make sure that data is not being transmitted from the instrument. (Data is transmitted only by playing notes on the keyboard or playing back a song.) • While the computer is connected to the instrument, you should wait for six seconds or more between these operations: (1) when turning the power of the instrument off then on again, or (2) when alternately connecting/ disconnecting the USB cable. Rear panel USB cable MOXF6/MOXF8 Owner’s Manual 53 Quick Guide Creating a Song with a computer MIDI channels and MIDI ports MIDI data is assigned to one of sixteen channels, and this synthesizer is capable of simultaneously playing sixteen separate Parts, via the sixteen MIDI channels. However, the sixteen-channel limit can be overcome by using separate MIDI “ports,” each supporting sixteen channels. While a single MIDI cable is equipped to handle data over up to sixteen channels simultaneously, a USB connection is capable of handling far more—thanks to the use of MIDI ports. Each MIDI port can handle sixteen channels, and the USB connection allows up to eight ports, letting you use up to 128 channels (8 ports x 16 channels) on your computer. When connecting this instrument to a computer using a USB cable, the MIDI ports are defined as follows: Port 1 The tone generator block in this instrument can recognize and use only this port. When playing the MOXF6/MOXF8 as a tone generator from the external MIDI instrument or computer, you should set the MIDI Port to 1 on the connected MIDI device or computer. Port 2 This port is used to control the DAW software on the computer from the MOXF6/MOXF8 by using the Remote Control feature. By using the MOXF6/MOXF8 with the DAW software on the computer connected to the MOXF6/MOXF8, you can take advantage of the following functions and applications. • MIDI recording and Audio recording of the MOXF6/MOXF8 performance to the DAW software on the computer. • Playing back a song of the DAW software by using the MOXF6/MOXF8 tone generator This section contains an overview on how to use DAW software on the computer with the MOXF6/MOXF8 after connecting. Recording your performance on the MOXF6/MOXF8 to computer Setting up the MOXF6/MOXF8 1 Port 3 This port is used as the MIDI Thru Port. The MIDI data received over Port 3 via the USB [TO HOST] terminal will be re-transmitted to an external MIDI device via the MIDI [OUT] terminal. The MIDI data received over Port 3 via the MIDI [IN] terminal will be re-transmitted to an external device (computer, etc.) via the USB [TO HOST] terminal. If Quick Setup 1 is set to the default settings, simultaneously hold the [QUICK SETUP] button and press the Group [A] button. This should be selected when recording your keyboard performance to the DAW software on the computer. If Quick Setup 1 is not set to the default settings, set as follows. Audio settings Use this setting when recording the signals from the tone Port 4 This port is used only for data communication of the MOXF6/ MOXF8 Editor. No other software or device can use this port. generator and the A/D INPUT [L]/[R] jacks separately to DAW software, and playing the signals from the OUTPUT [L/ MONO]/[R] jacks directly. Port 5 This port is used only for data communication of the MOXF6/ MOXF8 Remote Editor. Mode Direct Monitor SW A/D In & Part Part on on 2StereoRec No other software or device can use this port. When using a USB connection, make sure to match the MIDI transmit port and the MIDI receive port as well as the MIDI transmit channel and the MIDI receive channel. Make sure to set the MIDI port of the external device connected to this instrument according to the above information. MIDI settings Use this setting when recording this instrument’s performance (not including Arpeggio data) to the DAW software. Local Control off MIDI Sync auto Clock Out off Audio channels ARPOUTSw all off The audio signals of the MOXF6/MOXF8 can be output to the USB [TO HOST] terminal and the OUTPUT [L/MONO]/[R] jacks. When connecting to a computer, use the USB [TO HOST] terminal. In this case, up to four audio channels (USB 1 – USB 4) are available. The output-to-channel assignments are made in the [F5] USB I/O display of the Utility mode. KBDTxCh 1 TrIntSw all on TrExtSw all on NOTE For more details regarding these parameters, see the “Reference Manual” PDF document. The audio signals of the MOXF6/MOXF8 can be input from the USB [TO HOST] terminal and the A/D INPUT [L]/[R] jacks. Up to two channels of audio can be input to the USB [TO HOST] terminal. Set the output level by using the [DAW LEVEL] slider on the MOXF6/MOXF8. The signals are output to the OUTPUT [L/MONO]/[R] jack. Also, up to two audio channels can be input to the A/D INPUT [L]/[R] jacks. The signal is sent to the A/D input part of the MOXF6/MOXF8. For more details, see the “Reference Manual” PDF document. 54 MOXF6/MOXF8 Owner’s Manual 2 Press the [STORE] button to store the settings to internal memory. 3 Press the desired mode button for playing, and then select the desired program for recording. Quick Guide 4 In the Performance/Song/Pattern mode, set the output channel of the Audio signal for each part. 2 Select the Song or Pattern to be edited. When the output setting for the audio signal (“Mode” 3 Press the [MIXING] button to call up the Mixing display. 4 Set up the Mixing for parts 1 – 16 as necessary. parameter) is set to “2StereoRec” in Step 1, you can change the audio output channel for each part. In the Performance mode, this parameter can be set in the [F4] USB I/O display of Common Edit. In the Song/Pattern mode, this parameter From the Mixing display, you can select Voices and set can be set in the [F4] USB I/O display of Mixing Common various parameters such as pan, volume, balance between Edit. the Chorus/Reverb and dry sound, Insertion effect on/off and Arpeggio on/off. NOTE In the Voice mode, the audio output channel is fixed to USB 3/4. Setting up the DAW software on the computer Setting up the DAW software on the computer 1 1 Set the MIDI output port of the Tracks for playing the MOXF6/MOXF8 to Port 1 of the “MOXF6/ MOXF8” 2 example below, the MIDI data transmitted from the MOXF6/ Enter the MIDI data to each Track of the DAW software on the computer. MOXF8 then recorded to the computer via MIDI channel 1 The tone generator settings of the part corresponding to the will be returned back from the computer to the MOXF6/ MIDI Track will be set in the Mixing mode on the MOXF6/ MOXF8 via MIDI channel 3 according to the setting of the MOXF8. Set MIDI Thru to “on” on the DAW software. By setting MIDI Thru to “on,” the MIDI data generated by playing the keyboard and transmitted to the computer will be returned back to the MOXF6/MOXF8. As shown in the recording Track. As a result, the tone generator of the NOTE When using Cubase as the DAW, you can create an original MOXF6/MOXF8 will sound the MIDI data generated by Mixing setup of the MOXF6/MOXF8 from the MOXF6/MOXF8 Editor on your computer. The created Mixing setup can be saved as a Cubase Project file for future recall. playing the keyboard as MIDI data from channel 3. USB TO HOST terminal Tone generator block (recognizing MIDI Channel 3 data) Keyboard (output via MIDI Channel 1) Local Control = off MOXF6/MOXF8 Computer (Cubase, etc.) IN CH1 OUT CH3 MIDI Thru = on Song playback from a computer using the MOXF6/MOXF8 as a tone generator The instructions below show how to use this instrument as a MIDI tone generator. In this case, actual MIDI sequence data is transmitted from DAW software on the computer, allowing you to avoid using software synths and save processing power on your computer. Remote-controlling the software from the MOXF6/MOXF8 (Remote mode) The MOXF6/MOXF8 features a highly convenient Remote mode which lets you control the DAW software and software synthesizer on your computer via the panel operations of the MOXF6/MOXF8. For example, you can start/stop playback of the DAW software on the computer by using the Function buttons and control the song position on the DAW software by using the [DATA] dial, [INC] and [DEC] buttons instead of using the mouse or computer keyboard. Remote-controlling the software synthesizer Up to 50 Control Templates of VST Instruments can be stored to internal memory of this instrument. With these, you can use the MOXF6/MOXF8 to control various software synthesizers. Use the MOXF6/MOXF8 Remote Editor for editing the Control Template. NOTE To use the MOXF6/MOXF8 Remote Editor, you need to install the Setting up the MOXF6/MOXF8 1 Press the [SONG] or [PATTERN] button to enter the Song mode or Pattern mode. MOXF6/MOXF8 Remote Tools. The MOXF6/MOXF8 Remote Tools consists of two components: MOXF6/MOXF8 Remote Editor and MOXF6/MOXF8 Extension, which enables you to use the MOXF6/ MOXF8 along with Cubase series. MOXF6/MOXF8 Owner’s Manual 55 Quick Guide Setting up the DAW software on the computer MOXF6/MOXF8 Remote Tools can be downloaded from the following Yamaha web site. For details on operating the MOXF6/MOXF8 Remote Editor, see the PDF manual supplied with the MOXF6/MOXF8 Remote Editor. This section explains how to set up after starting each application. NOTE When the cable between the MOXF6/MOXF8 and the Windows computer is disconnected or the MOXF6/MOXF8 is turned off accidentally, the DAW will not recognize the MOXF6/MOXF8 again even if you connect the cable again or turn the MOXF6/ MOXF8 on. If this occurs, exit the DAW software, then restart it after setting up the MOXF6/MOXF8 and making sure the connection is secure. http://download.yamaha.com/ Remote-controlling the DAW software The DAW applications Cubase, Logic Pro, SONAR and Digital Performer can be controlled via the Remote Control mode of the MOXF6/MOXF8. For the most recent information on DAW software that can be controlled from the MOXF6/MOXF8, see the following URL: http://www.yamahasynth.com/ Before you can use the Remote Control function, you’ll need to follow the setup instructions below. J Cubase The settings will be completed by installing MOXF6/MOXF8 Remote Tools. J SONAR 1 Pull down the [Options] menu and select [MIDI Devices] to call up the “MIDI Devices” window. 2 Add “Yamaha MOXF6/MOXF8-2” to the Input Device, then add “Yamaha MOXF6/MOXF8-2” to the Output Device. 3 Pull down the [Options] menu and select [Control Surfaces] to call up the Control Surface window. 4 Click the [+] button, select “Mackie Control,” then set the Input Port to “Yamaha MOXF6/MOXF8-2” and set the Output Port to “Yamaha MOXF6/MOXF8-2.” NOTE Before making the setup of DAW Remote, make sure to properly install the Yamaha Steinberg USB Driver and the MOXF6/MOXF8 Remote Tools. Setting up the MOXF6/MOXF8 1 Connect this instrument to the computer via a USB cable (page 53). 2 Press the [DAW REMOTE] button to enter the Remote mode. 3 Press the [UTILITY] button to call up the REMOTE display of the Utility mode. Then set the “DAW Select” to the desired DAW software. 4 Press the [STORE] button to store the settings to internal memory. 5 Start the DAW software on the connected computer. J Digital Performer 1 In the Audio/MIDI setup of a Mac computer, connect Port 2 of the interface of the MOXF6/MOXF8 to Port 2 of the tone generator. When there is only one Port for the tone generator, add the new Port, then connect it to the interface. 2 Pull down the [Setup] menu and select [ControlSurface Setup] to call up the Control Surface window. 3 Click the [+] button. 4 Select “Mackie Control” in the Driver section. 5 In the box for setting “Unit” and “MIDI,” select “Mackie Control” in the “Unit” section and select “MOXF6/MOXF8 New Port 2” in the “MIDI” section. J Logic Pro 56 MOXF6/MOXF8 Owner’s Manual 1 Select the [Preference] menu  [Control Surfaces]  [Settings] to call up the Settings window. 2 Select the [New] menu  [Install]. 3 Select “Mackie Control” in the model list, then add it as a control surface. Quick Guide 4 Set the MIDI Output Port to “Yamaha MOXF6/MOXF8 Port2.” 5 Set the MIDI Input Port to “Yamaha MOXF6/MOXF8 Port2.” Using as a Master Keyboard The Master mode lets you: NOTE Mackie Control is the trademark of Mackie Designs, Inc. For details about the button operations and functions, see the “Reference Manual” PDF document. Using the MOXF6/MOXF8 Editor I Create and store up to 128 programs, each containing a Voice, a Performance, a Song, or a Pattern, and each of which can be instantly called up for use. I Assign up to four separate Zones in each Master program for use as a master keyboard. You can use the Master mode to memorize the settings you use most often including the information on which mode is used, and call up these settings instantly anytime you need them with a single button press. Furthermore, you can memorize the settings for controlling an external MIDI device by the Master, allowing you to change and control the connected external MIDI tone generator in sequence while performing live. About the MOXF6/MOXF8 Editor The MOXF6/MOXF8 Editor lets you edit Voice and Mixing setups from your computer, giving you even greater editing convenience. Furthermore, the data edited on the MOXF6/ MOXF8 is always synchronized with the data on the computer (MOXF6/MOXF8 Editor) and vice versa. This provides a smooth, seamless interface, making it exceptionally easy to create and edit data. Using the MOXF6/MOXF8 Editor Using the MOXF6/MOXF8 Editor VST in Cubase The MOXF6/MOXF8 Editor VST works as a VST3 plug-in software in Cubase. In this case, you can launch the MOXF6/ MOXF8 Editor via the same operations as that of any other VST Instrument. Registering the Edited Voice/ Performance/Song/Pattern The Master mode is ideal for live performance situations since it lets you instantly switch among needed Voices, Songs, Patterns and Performances without having to change modes. One convenient way of using the Master mode is to save your needed programs (Voices, Performances, etc.) to Masters in number order, according to the songs you intend to perform. Follow the instructions below to store programs. 1 Press the [MASTER] button to enter the Master mode. 2 Select a Master to be edited. Using the MOXF6/MOXF8 Editor separately The MOXF6/MOXF8 Editor can also be used as a standalone application. The Master Play display appears. 3 Press the [F2] MEMORY button. The MEMORY display appears. The MOXF6/MOXF8 Editor can be downloaded from the following URL: http://download.yamaha.com/ For instructions on using the MOXF6/MOXF8 Editor, refer to the respective PDF manuals included with the software. HINT Integration between MOXF6/MOXF8 and Cubase 4 At the “Mode” parameter and “Memory” parameter, select the desired mode and program. 5 Press the [STORE] button to store the set the Master program in the store display. When producing music by using the MOXF6/MOXF8 together with Cubase, the MOXF6/MOXF8 Extension contained in the MOXF6/MOXF8 Remote Tools provides useful and convenient functions. For example, the necessary settings for connection will be made automatically. For more details, including the latest information, see the following URL. http://www.yamahasynth.com/ MOXF6/MOXF8 Owner’s Manual 57 Quick Guide Making settings for use as a master keyboard Making Global System Settings (Utility Mode) It is a good idea to memorize master keyboard functions to the Master when using external multiple MIDI tone generators. Simply by selecting a different Master, you can change the programs in your connected external MIDI tone generators. Here's how to do it: In the Utility mode, you can set parameters that apply to the entire system of this instrument. To enter the Utility mode, press the [UTILITY] button. Pressing the [EXIT] button returns to the original display. This section describes some useful functions in the Utility mode. 1 Press the [MASTER] button to enter the Master mode. 2 Select a Master to be edited. 3 Press the [F3] ZONE SW button. The ZONE SW display appears. Setting the default mode when turning the power on [F1] GENERAL  [SF6] OTHER  Cursor [>] button  “PowerOnMode” Determines which mode is automatically called up when turning the power on. 4 Set “ZoneSwitch” to “on.” NOTE When the “ZoneKnob” is set to “on,” the Zone Edit settings are assigned to Knobs 1 – 8. If you want to assign the settings in the memorized mode to Knobs 1 – 8 yourself, set “ZoneKnob” to “off.“ 5 Press the [EDIT] button, and then press the Number [1] button. This calls up the Master Edit displays for Zone 1. 6 Set the parameters for Zone 1 in the [F1] – [F5] displays. 7 Use the Number [2] – [4] buttons to set the parameters for other Zones as well as Zone 1. 8 After setting all the desired parameters, press the [STORE] button to store your settings as a Master program. After completing these settings, assign a name to the Master in the [F1] Name display of the Master Common Edit. After naming, press the [STORE] button to store the Master. For more information on the parameters which are edited in the Master mode, see the “Reference Manual” PDF document. 58 MOXF6/MOXF8 Owner’s Manual When this is set to “STORE+ENTER,” the display in which you specify the mode (Voice/Performance/Master/Song/ Pattern) and the Program number will automatically be called up when the power is turned on. To specify a display, call it up normally, then press the [STORE] button and the [ENTER] button simultaneously. Quick Guide Reversing the LCD status [F1] GENERAL  [SF6] OTHER  Cursor [<] button  “LCD Mode” This parameter determines the LCD status. When “normal” is selected: Master Effect/Master EQ settings in the Voice mode [F2] VOICE  [SF1] MFX, [SF2] MEQ Determines how much of the Effect and EQ processing is applied to the master output. When “reverse” is selected: Transmitting Control Change messages using the Foot Switch You can use the Master mode to memorize the settings you use most often. Click (metronome) settings [F4] CTL ASN  [SF2] FT SW You can transmit Control Change messages using the Foot Switch connected to the [ASSIGNABLE] jack. For example, when you set the value to 98 [PC Inc], the Program Change number increases by 1 whenever the Foot Switch is pressed. [F2] SEQ  [SF1] CLICK Determines the tempo, volume and output destination of the click (metronome). Effect settings applied to the signal input from the A/D INPUT jack [F3] VCE A/D Determines the settings for the effects applied to the incoming audio signal from the A/D INPUT [L]/[R] jacks in the Voice mode. MOXF6/MOXF8 Owner’s Manual 59 Quick Guide Saving/Loading Data (File Mode) display. By pressing the [SF2] SET NAME button, the file/ directory name which selected in the file/directory selection box is copied to the file name field. The File mode provides tools for transferring data (such as Voice, Performance, Song, and Pattern) between the MOXF6/MOXF8 and external USB flash memory device connected to the USB [TO DEVICE] terminal. To enter the File mode, press the [FILE] button. This section explains how to save/load all the data on the user memory of this instrument as an “All” file. File name field 5 Saving the settings to a USB flash memory device 1 Connect a USB flash memory device to the USB [TO DEVICE] terminal of this instrument. 2 Press the [FILE] button, and then press the [F2] SAVE button. The SAVE display appears in the File mode. Press the [SF1] EXEC button to save the file. Loading the settings from a USB flash memory device 1 Connect a USB flash memory device to the USB [TO DEVICE] terminal of this instrument. 2 Press the [FILE] button, and then press the [F3] LOAD button. The LOAD display appears in the File mode. 3 Set “TYPE” to “All,” and then select the desired directory of the device. After that, press the [ENTER] button. If storing the root directory, keep the directory set to “root” without pressing the [ENTER] button. If you want to make a new directory, press the [SF3] NEW button. Set the desired file type for saving The current determined directory as the save destination of the USB flash memory device File/Directory Selection box Select the desired directory of the USB flash memory device, and then press the [ENTER] button. 4 Use the Cursor [<]/[v] buttons to move the cursor to the file name field, assign a name to the file, and then press the [ENTER] button. Move to the desired location in the file name field by using the Cursor [<]/[>] buttons, and then select the desired characters by using the [DATA] dial or the [INC]/[DEC] button to enter the selected character. By pressing the [SF6] button, you can assign the name in the Character List 60 MOXF6/MOXF8 Owner’s Manual 3 Set “TYPE” to “All,” and then select the file (extension: .X6A) of the memory. Select the directory which has desired file in the file/directory selection box, and then press the [ENTER] button. After that, select the desired file. Quick Guide 4 Press the [SF1] EXEC button to load the file. NOTICE The Load operation overwrites any data previously existing in the specified destination internal memory. Important data should always be saved to a USB flash memory device connected to the USB [TO DEVICE] terminal. Precautions when using the USB [TO DEVICE] terminal This instrument features a built-in USB [TO DEVICE] terminal. When connecting a USB device to the terminal, be sure to handle the USB device with care. Follow the important precautions below. J Connecting/removing the USB flash memory device Before removing the memory from the instrument, make sure that the instrument is not accessing data (such as in the Save, Copy and Delete operations). NOTICE Avoid frequently turning the power on/off to the USB flash memory device, or connecting/disconnecting the memory too often. Doing so may result in the operation of the instrument “freezing” or hanging up. While the instrument is accessing data (such as during Save, Copy, Delete, Load and Format operations) or is mounting the USB flash memory device (shortly after the connection), do NOT unplug the USB connector, do NOT remove the device from the instrument, and do NOT turn the power off to either the instrument or the USB flash memory device. Doing so may corrupt the data on either or both. NOTE For more information about the handling of USB devices, refer to the owner’s manual of the USB device. J Compatible USB devices Only USB memory devices of the flash-memory variety can be used with the MOXF6/MOXF8. Furthermore, the instrument does not necessarily support all commercially available USB flash memory devices, nor can Yamaha guarantee operation such USB devices that you purchase. Before purchasing a USB flash memory device for use with this instrument, please visit the following web page: http://download.yamaha.com/ J Connecting a USB flash memory device When connecting a USB flash memory device to the USB [TO DEVICE] terminal, make sure that the connector on the memory is appropriate and that it is connected in the proper direction. NOTE Though the instrument supports the USB 1.1 standard, you can connect and use a USB 2.0 storage device with the instrument. However, note that the transfer speed is that of USB 1.1. J Formatting a USB flash memory device When a USB flash memory device is connected, a message may appear prompting you to format the memory. If so, execute the Format operation (see the “Reference Manual” PDF document). NOTICE The format operation overwrites any previously existing data. Make sure that the device you are formatting does not contain important data. J To protect your data (write-protect) To prevent important data from being inadvertently erased, apply the write-protect provided on the USB flash memory device. If you are saving data to the device, make sure to disable write-protect. MOXF6/MOXF8 Owner’s Manual 61 Appendix Shift Function List Some of the important functions and operations on the instrument can be executed with convenient panel control shortcuts. Simply hold down the [SHIFT] button and press the indicated button (as described below). Mode 62 Operation Function All modes [SHIFT] + [INC]/[DEC] Increases/decreases the value by 10. (Program number in the Play mode; parameter value in the Edit mode) All modes [SHIFT] + [DATA] dial Increases/decreases the value by 10. (Same as [SHIFT] + [INC]/[DEC]) Voice Play [SHIFT] + BANK SELECT [DEC]/[INC] Changes the Voice Bank in the order listed below. PRE1  USR1  PDR  UDR  GM  GMDR All modes other than the File mode [SHIFT] + Knob 1 – 8 Increases/decreases the value by 10. All modes other than the File mode [SHIFT] + Knob Function 1 button Sets the Knob Function to TONE 1. All modes other than the File mode [SHIFT] + Knob Function 2 button Sets the Knob Function to EQ. All modes [SHIFT] + [Level] Meter button Sets the [LEVEL] meter to the A/D INPUT level. Voice/Performance/ Song Mixing/Pattern Mixing/Master mode [SHIFT] + the current mode button Executes the BULK Job of the current mode. Voice Play/ Performance Play/ Category Search display [SHIFT] + [FAVORITE] Voice/Performance/ Song/Pattern mode [SHIFT] + ARP [ON/OFF] • In the Voice mode, this operation will call up the [F3] MAIN display of Arpeggio Edit. • In the Performance/Song/Pattern mode, this operation will call up the [F1] COMMON display of Arpeggio Edit. Voice/Performance/ Song/Pattern mode [SHIFT] + A/D INPUT [ON/OFF] • In the Voice mode, this operation will call up the [F3] VCE A/D – [SF1] OUTPUT display of the Utility mode. • In the Performance mode, this operation will call up the [F5] A/D IN – [SF1] OUTPUT display of Common Edit. • In the Song/Pattern mode, this operation will call up the [F5] A/D IN – [SF1] OUTPUT display of Mixing Common Edit. Voice/Performance/ Song/Pattern mode [SHIFT] + EFFECT [INSERTION] Calls up the [F6] EFFECT – [SF1] CONNECT display of Common Edit. Voice/Performance/ Song/Pattern mode [SHIFT] + EFFECT [SYSTEM] Calls up the [F6] EFFECT – [SF1] CONNECT display of Common Edit. Voice/Performance/ Song/Pattern mode [SHIFT] + EFFECT [MASTER] • In the Voice mode, this operation will call up the [F2] VOICE – [SF1] MFX display of the Utility mode. • In the Performance mode, this operation will call up the [F2] OUT MFX – [SF2] MFX display of Common Edit. • In the Song/Pattern mode, this operation will call up the [F2] MFX display of Mixing Common Edit. Voice/Performance/ Song/Pattern mode [SHIFT] + ASSIGNABLE FUNCTION [1]/[2] • In the Voice mode, this operation will call up the [F1] GENERAL – [SF4] OTHER display of Common Edit. • In the Performance mode, this operation will call up the [F1] GENERAL – [SF5] OTHER display of Common Edit. • In the Song/Pattern mode, this operation will call up the [F1] GENERAL display of Mixing Common Edit. Voice/Performance/ Song/Pattern mode [SHIFT] + OCTAVE [-]/[+] Calls up the [F1] GENERAL – [SF3] KBD display of the Utility mode. Voice/Performance/ Song/Pattern mode [SHIFT] + TRANSPOSE [-]/[+] Calls up the [F1] GENERAL – [SF3] KBD display of the Utility mode. MOXF6/MOXF8 Owner’s Manual Favorite indicator Turns on/off the Favorite indicator of the current Voice or Performance. Appendix Display Messages LCD indication Description All remote templates stored. Appears when you store the Control Template in the Remote mode. Are you sure? Confirms whether you want to execute a specified operation or not. Arpeggio memory full. The internal memory for Arpeggio data is full. Arpeggio type copied. The Arpeggio Types are copied to the [SF1] – [SF6] buttons. Bad USB device. The USB flash memory device connected to this instrument is unusable. Format the USB flash memory device and try again. Bulk protected. Bulk data cannot be received because of the setting in the Utility mode. Can't undo. OK? When certain Song/Pattern Jobs are executed, internal memory becomes too full for use of the Undo operation. Completed. The specified load, save, format, or other Job has been completed. Device number is off. Bulk data cannot be transmitted/received since the device number is off. Device number mismatch. Bulk data cannot be transmitted/received since the device numbers don’t match. Edited data will be discarded. Prompts you to confirm whether or not to erase the edited data. Edits will be stored by loading. Confirms whether or not you want to continue the Load operation. If you select yes, the current edits will be stored. Edits will be stored by saving. Confirms whether or not you want to continue the Save operation. If you select yes, the current edits will be stored. Empty Favorite! [SHIFT]+[FAVORITE] to add. Appears when you press the [FAVORITE] button with no program registered to the Favorite Category. Executing… A format operation or Job is being executed. Please wait. File already exists. A file having the same name as the one you are about to save already exists. File not found. The file of the specified type cannot be found. Folder is too deep. Directories below this level cannot be accessed. Illegal file name. The specified file name is invalid. Try entering a different name. Illegal file. The file specified for loading is unusable by this instrument or cannot be loaded in the current mode. Illegal input. An invalid input or value has been specified. Check the input method or value. Illegal measure. An invalid measure number has been specified in the Song/Pattern mode. Select the measure again. Illegal phrase number. An invalid phrase number has been specified in the Pattern mode. Select the phrase again. Illegal Track number. An invalid Track number has been specified in the Song/Pattern mode. Select the Track again. Incompatible USB device A USB device which cannot be used with this instrument has been connected to the USB [TO DEVICE] terminal. MIDI buffer full. Failed to process the MIDI data because too much data was received at one time. MIDI checksum error. An error occurred when receiving bulk data. MIDI data error. An error occurred when receiving MIDI data. Mixing Voice full. The Mixing Voice cannot be stored because the number of Voices already stored has exceeded the maximum capacity. New Flash Memory Module. Please load waveform data. This message appears when the Flash Memory Expansion Module (FL512M/FL1024M) which was installed in a different MOXF has been installed to the current MOXF. If this message appears, you should save the Waveform data (including the parameter settings) of the previous MOXF to a USB storage device, connect the USB storage device to the current MOXF, then load the Waveform data. This occurs because the Sample without the parameter settings cannot produce the proper sound. No data. When a Song/Pattern Job is executed, the selected Track or range contains no data. Select an appropriate Track or range. In addition, this message appears when a Job related to a Mixing Voice cannot be executed because the specified Mixing Voice is not available. No F7 (End of Exc.) Exclusive data has been entered or changed without the necessary “End of Exclusive” byte (F7). Make sure the F7 message is included. No Flash Memory Module installed or module is unformatted. This message appears when no Flash Memory Expansion Module is installed or the unformatted Module has been installed. No response from USB device There is no response from the USB device connected to the USB [TO DEVICE] terminal. No sample data. This message appears when you try loading Waveform data with the “with sample” checkmark removed, even when the corresponding Sample is not available on the Flash Memory Expansion Module. Not empty folder You have attempted to delete a folder that contains data. Not empty waveform. You have attempted to load Waveform data to a Waveform that already contains data. MOXF6/MOXF8 Owner’s Manual 63 Appendix LCD indication Now Installing data to Flash Memory Module 64 Description The Sample data is being copied to the Flash Memory Expansion Module. Now loading... Indicates that a file is being loaded. Now saving... Indicates that a file is being saved. Now working... Canceling the Load/Save operation, after the [EXIT] button has been pressed. Overwrite? A save operation will overwrite data on the USB flash memory device, and this message confirms whether it is OK to continue or not. Part ** is used for Drum Assign. This message appears when the Part switches of all Parts are set to on, and the Drum Assign function uses Part ** for the Drum Part in Performance mode. The ** mark indicates the Part number. Part ** is used for Layer. This message appears when the Part switches of all Parts are set to on, and the Layer function uses Part ** for the Layer Part in the Performance mode. The ** mark indicates the Part number. Part ** is used for Split. This message appears when the Part switches of all Parts are set to on, and the Split function uses Part ** for the Split Part in the Performance mode. The ** mark indicates the Part number. Phrase limit exceeded. The maximum number of Phrases (256) has been exceeded when recording, executing a Pattern Job, or editing. Please keep power on. The data is being written to Flash ROM. Never attempt to turn off the power while data is being written to Flash ROM. Turning the power off while this message is shown results in loss of all user data and may cause the system to freeze (due to corruption of data in the Flash ROM). This may also result in this instrument being unable to properly start up the next time the power is turned on. Please reboot. Please restart this instrument. Please stop sequencer. The operation you have attempted to execute cannot be done during Song/Pattern playback. Power on mode stored. The settings in the Power On mode (pressing the [STORE] and [ENTER] buttons simultaneously) have been stored. Quick Setup ** applied. Quick Setup ** has just been applied to this instrument. The ** mark indicates the Quick Setup number. Read only file. You have attempted to delete, rename, or overwrite a read-only file. Receiving MIDI bulk This instrument is receiving MIDI bulk data. Sample is too long. The Sample size is too large and the load operation cannot be executed. Sample full. The maximum overall number of Samples has been exceeded. Sample memory full. The Sample memory is full and further Jobs or load operations cannot be executed. Scene & Arpeggio type stored The Song Scene and current Arpeggio type have been stored to one of the [SF1] – [SF6] buttons. Sequence memory full. The internal memory for Sequence data is full, preventing any further operation (such as recording, editing, Job execution, MIDI reception/transmission, or loading from the external storage device). Try again after erasing unwanted Song, Pattern, or User Phrase data. Too many fixed notes When converting the Song or Pattern data to the Arpeggio data, the amount of different notes in the data to be converted has exceeded sixteen. Transmitting MIDI bulk This instrument is transmitting MIDI bulk data. Unrecognized Flash Memory Module. Please format that. An unformatted Flash Memory Expansion Module has been recognized. Execute the Format operation. USB connection terminated. A break in the connection with the USB flash memory device has occurred because of an abnormal electric current. Disconnect the device from the USB [TO DEVICE] terminal, then press the [ENTER] button. USB device connecting Currently recognizing the USB flash memory device connected to the USB [TO DEVICE] terminal. USB device full. The USB flash memory device is full and no more data can be saved. Use a new USB flash memory device, or make space by erasing unwanted data from the USB flash memory device. USB device not ready. A USB flash memory device is not properly inserted in or connected to the USB [TO DEVICE] terminal. USB device read/write error. An error occurred while reading or writing to/from a USB flash memory device. USB device write protected. The USB flash memory device is write protected, or you have attempted to write to read-only media. Utility stored The settings in the Utility mode have been stored. Waveform full. The maximum overall number of Waveforms has been exceeded. Waveform is protected. You have attempted to load protected Waveform data. MOXF6/MOXF8 Owner’s Manual Appendix Troubleshooting No sound? Wrong sound? When a problem like this occurs, please check the following points before assuming that the product is faulty. Many problems can be solved by executing the Factory Set operation (page 20), after backing up your data to an USB flash memory device (page 60). If the problem persists, consult your Yamaha dealer. No Sound.  Is this instrument properly connected to related external equipment (e.g., amplifier, speaker, headphone) via audio cables? Since this instrument has no built-in speakers, you will need an external audio system or a set of stereo headphones to properly monitor it (page 17).  Is the power of this synthesizer and any external equipment connected to it turned on?  Have you made all the appropriate level settings—including the Master Volume on this instrument and the volume settings on any connected external equipment? If the Foot Controller is connected to the [FOOT CONTROLLER] jack, operate the Foot Controller and check the sound volume.  Check the Local Control parameter in the Utility mode. When this instrument is used by itself and this parameter is set to off, no sound is produced even if you play the keyboard. [UTILITY]  [F6] MIDI  [SF2] SWITCH  “LocalCtrl”  Check the Direct Monitor Switch parameter in the Utility mode. When this instrument is used by itself and this parameter is set to off, no sound is produced even if you play the keyboard. [UTILITY]  [F5] USB I/O  “DirectMonitorSw Part”  When the Performance/Song/Pattern produces no sound, is the “ArpPlyOnly” parameter of each Part turned on? When this parameter is turned on, the corresponding Part produces sound only via Arpeggio playback. [PERFORM]  [EDIT]  Number [1] – [4]  [F1] VOICE  [SF2] MODE  “ArpPlyOnly?” [SONG]/[PATTERN]  [MIXING]  [EDIT]  Number [1] – [16]  [F1] VOICE  [SF2] MODE  “ArpPlyOnly”  Are the MIDI volume or MIDI expression settings too low when using the external controller?  Are the effect and filter settings appropriate? If you are using the filter, try changing the cutoff frequency. Some cutoff settings may filter out all of the sound. [VOICE]  [F6] EFFECT [PERFORM]  [F6] EFFECT [SONG]/[PATTERN]  [MIXING]  [F6] EFFECT [VOICE]  [EDIT]  Element/Key selection  [F3] FILTER [PERFORM]  [EDIT]  Part selection  [F4] TONE  [SF1] FILTER [SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F4] TONE  [SF1] FILTER [SONG]/[PATTERN]  [UTILITY]  [F2] SEQ  [SF2] FILTER  Is “Vocoder” selected as the Insertion Effect Type of the Voice? If so, set the parameters related to the AD Part and A/D INPUT connector to the appropriate values then play the keyboard while speaking into the connected microphone. Check whether or not the A/D INPUT [GAIN] Knob on the rear panel is set to the minimum position. [VOICE]  [F6] EFFECT  [SF1] CONNECT  “InsEF Connect”  Are the volume or expression settings too low? [UTILITY]  [F1] GENERAL  [SF1] TG  “Volume” [VOICE]  [EDIT]  [COMMON]  [F2] OUTPUT  “Volume” [VOICE]  [EDIT]  Element/Key selection  [F4] AMP  [SF1] LVL/PAN  “Level” [PERFORM]  [EDIT]  [COMMON]  [F2] OUT/MFX  [SF1] OUT  “Volume” [PERFORM]  [EDIT]  Part selection  [F2] OUTPUT  [SF1] VOL/PAN  “Volume” [SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F2] OUTPUT  [SF1] VOL/PAN  “Volume”  Are the parameter settings such as Element Switch, Part Switch, Note Limit and Velocity Limit appropriate? [VOICE]  [EDIT]  Element/Key selection  [F1] OSC  [SF1] WAVE  “ElementSw” [VOICE]  [EDIT]  Element/Key selection  [F1] OSC  [SF3] LIMIT [PERFORM]  [F2] VOICE [PERFORM]  [EDIT]  Part selection  [F1] VOICE  [SF1] VOICE  “PartSw” [PERFORM]  [EDIT]  Part selection  [F1] VOICE  [SF3] LIMIT MOXF6/MOXF8 Owner’s Manual 65 Appendix  When playing the keyboard in the Performance/Song/Pattern mode produces no sound, has a Voice been properly assigned to each Part? [PERFORM]  [F2] VOICE [SONG]/[PATTERN]  [MIXING]  [F2] VOICE  When Song/Pattern playback produces no sound, are the output channel of each Track in the play mode and the receive channel of each Part in the Mixing mode set appropriately? [SONG]/[PATTERN]  [F3] TRACK [SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F1] VOICE  [SF2] MODE  “ReceiveCh”  When Song/Pattern playback produces no sound, is the Velocity Offset setting of the Groove appropriate? [SONG]/[PATTERN]  [F2] GROOVE  “VELO OFST” No sound from the A/D INPUT jack  Is the switch of the microphone turned on?  Check the microphone type. Make sure to use a dynamic microphone.  Is the cable between the microphone or audio equipment and this instrument properly connected?  Is the A/D INPUT [GAIN] knob turned fully counter-clockwise (to the minimum)?  Is the A/D INPUT [ON/OFF] button turned on?  Check whether or not the connection status of the A/D INPUT [L]/[R] matches the “Mono/Stereo” parameter. [VOICE]  [UTILITY]  [F3] VCE A/D  “Mono/Stereo” [PERFORM]  [EDIT]  [COMMON]  [F5] A/D IN  “Mono/Stereo” [SONG]/[PATTERN]  [MIXING]  [EDIT]  [COMMON]  [F5] A/D IN  “Mono/Stereo”  Check whether or not the “Mic/Line” parameter is set to the appropriate value. When the output level of the connected equipment (such as a microphone, guitar, bass) is low, set this parameter to “mic.” When the output level of the connected equipment (such as a synthesizer keyboard, CD player) is high, set this parameter to “line.” [UTILITY]  [F1] GENERAL  [SF6] OTHER  Press [<] several times to call up the first page.  “Mic/Line”  Are the volume settings of the A/D Input Part too low? [VOICE]  [UTILITY]  [F3] VCE A/D  [SF1] OUTPUT  “Volume” [PERFORM]  [EDIT]  [COMMON]  [F5] A/D IN  [SF1] OUTPUT  “Volume” [SONG]/[PATTERN]  [MIXING]  [EDIT]  [COMMON]  [F5] A/D IN  [SF1] OUTPUT  “Volume”  Are the effect settings appropriate? [VOICE]  [UTILITY]  [F3] VCE A/D [PERFORM]  [EDIT]  [COMMON]  [F5] A/D IN [SONG]/[PATTERN]  [MIXING]  [EDIT]  [COMMON]  [F5] A/D IN  Is the output setting of the A/D Input Part set appropriately? [UTILITY]  [F4] USB I/O  Check whether or not the Vocoder Effect is selected. When Vocoder is selected as the Insertion Effect for the current Voice or for Part 1 of the current Performance/Song/Pattern, the audio signal input from the A/D INPUT jacks may produce no sound depending on the parameter settings. [VOICE]  [F6] EFFECT  “Ins EF Connect” Playback continues without stopping.  When the ARP [ON/OFF] button is turned on, press it so that its lamp is turned off.  When in the Song mode or Pattern mode, press the [J] (Stop) button.  When the click sound continues, check the following parameter setting. Set this parameter to something other than “all” because this setting always plays back the click sound regardless of the sequencer status. [SONG]/[PATTERN]  [UTILITY]  [F2] SEQ  [SF1] CLICK  “Mode” Distorted sound.  Are the effect settings appropriate? Use of an effect at certain settings may produce distortion. [VOICE]  [F6] EFFECT [PERFORM]  [F6] EFFECT [SONG]/[PATTERN]  [MIXING]  [F6] EFFECT 66 MOXF6/MOXF8 Owner’s Manual Appendix  Are the filter settings appropriate? Excessively high filter resonance settings can cause distortion. [VOICE]  [EDIT]  Element/Key selection  [F3] FILTER [PERFORM]  [EDIT]  Part selection  [F4] TONE  [SF1] FILTER [SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F4] TONE  [SF1] FILTER  Are any of the following volume parameters set so high that clipping is occurring? [UTILITY]  [F1] GENERAL  [SF1] TG  “Volume” [VOICE]  [EDIT]  [COMMON]  [F2] OUTPUT  Volume [VOICE]  [EDIT]  Element/Key selection  [F4] AMP  [SF1] LVL/PAN  “Level” [PERFORM]  [EDIT]  [COMMON]  [F2] OUT/MFX  [SF1] OUT  “Volume” [PERFORM]  [EDIT]  Part selection  [F2] OUTPUT  [SF1] VOL/PAN  “Volume” [SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F2] OUTPUT  [SF1] VOL/PAN  “Volume” Sound is cut off.  Is the entire amount of notes played (via your keyboard playback and Song/Pattern/Arpeggio playback) exceeding the maximum polyphony of this instrument? Only one note sounds at a time.  When this situation occurs, the Mono/Poly parameter in the current mode is set to “mono.” If you wish to play chords, set this parameter to “poly.” [VOICE]  [F4] PORTA  “Mono/Poly” [PERFORM]  [EDIT]  Part selection  [F1] VOICE  [SF2] MODE  “Mono/Poly” [SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F1] VOICE  [SF2] MODE  “Mono/Poly” Pitch is wrong.  Is the Master Tune parameter in the Utility mode set to a value other than “0”? [UTILITY]  [F1] GENERAL  [SF1] TG  “Tune”  Is the Note Shift parameter in the Utility mode set to a value other than “0”? [UTILITY]  [F1] GENERAL  [SF1] TG  “NoteShift”  When the Voice produces a wrong pitch, is the appropriate tuning system selected from Micro Tuning parameter in the Voice Edit mode? [VOICE]  [EDIT]  [COMMON]  [F1] GENERAL  [SF2] PLY MODE  “M. Tuning No.”  When the Voice produces a wrong pitch, is the LFO Pitch Modulation Depth in the Voice Edit mode set too high? [VOICE]  [EDIT]  Element/Key selection  [F5] LFO  “PMod”  When the Voice produces a wrong pitch, is the Coarse Tune or the Fine Tune in the Voice Edit mode set properly? [VOICE]  [EDIT]  Element/Key selection  [F2] PITCH  “Coarse” / “Fine”  When the Performance/Song/Pattern produces a wrong pitch, are the Note Shift and Detune parameters of each Part set to a value other than “0”? [PERFORM]  [EDIT]  Part selection  [F4] TONE  [SF1] TUNE [SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F4] TONE  [SF1] TUNE  When the Song/Pattern playback produces a wrong pitch, is the Note Offset parameter in the Groove display set to a value other than “0”? [SONG]/[PATTERN]  [F2] GROOVE  “NOTE OFST” No effect is applied.  Check the on/off status of the EFFECT [INSERTION]/[SYSTEM]/[MASTER] button.  Is the Reverb Send or Chorus Send set to a value other than “0”? [VOICE]  [EDIT]  [COMMON]  [F2] OUTPUT  “ChoSend” / “RevSend” [PERFORM]  [EDIT]  [COMMON]  [F2] OUT/MFX  [SF1] OUT  “ChoSend” / “RevSend” [SONG]/[PATTERN]  [MIXING]  [EDIT]  Part selection  [F2] OUTPUT  [SF1] VOL/PAN  “ChoSend” / “RevSend” MOXF6/MOXF8 Owner’s Manual 67 Appendix  Have any or all of the Elements’ Insertion Effect Output parameters been set to “thru” in the effect setting display in the Voice Edit mode? [VOICE]  [F6] EFFECT  [SF1] CONNECT  “EL: OUT 1-8”  Have any or all of the effect types been set to “thru” or “No Effect”?  When this occurs in the Performance mode/Song mode/Pattern mode, check whether the Insertion Switch (INS SW) parameters are set properly or not. [PERFORM]  [F6] EFFECT  [SF2] INS SW [SONG]/[PATTERN]  [MIXING]  [F3] EFFECT  [SF2] INS SW The Edit Indicator appears, even when parameters are not being edited.  Keep in mind that even though the Edit mode is not active, simply moving a Knob/Slider or playing back the Song/Pattern changes the current Voice, Performance, or Mixing, causing the Edit Indicator to appear. Cannot start the Arpeggio.  Check whether the ARP [ON/OFF] button is turned on or off.  When a User Arpeggio type is selected, does the currently selected Arpeggio actually contain data?  Are the Arpeggio related parameters such as Note Limit and Velocity Limit set appropriately? [VOICE]  ARP [EDIT]  [F4] LIMIT [PERFORM]  ARP [EDIT]  [F4] LIMIT [SONG]/[PATTERN]  ARP [EDIT]  [F4] LIMIT  When this situation occurs in the Performance/Song/Pattern mode, check the Arpeggio Switch parameter. If this parameter for the current Part is set to off, Arpeggio playback will not be triggered by your keyboard performance even if the ARP [ON/OFF] button is turned on. [PERFORM]  ARP [EDIT]  [F3] MAIN  Part selection  “Switch” [SONG]/[PATTERN]  ARP [EDIT]  [F3] MAIN  Part selection  “Switch”  Is the MIDI Sync parameter set to “internal” or “auto” (using internal clock)? [UTILITY]  [F5] MIDI  [SF3] SYNC  “MIDI Sync” = “auto” or “internal” Cannot stop the Arpeggio.  When Arpeggio playback does not stop even if you release the key, set the Arpeggio Hold parameter to “off.” [VOICE]  ARP [EDIT]  [F3] MAIN  “Hold” [PERFORM]  ARP [EDIT]  [F3] MAIN  Part selection  “Hold” [SONG]/[PATTERN]  ARP [EDIT]  [F3] MAIN  Part selection  “Hold” The Voice assigned to the Performance produces a different sound from the one in the Voice mode.  This is normal because the Voice sound is determined by the parameter settings in the Performance mode. To solve this problem, you will need to apply the same parameter settings as those used in the Voice mode via the following three steps. 1. Set the “P.WithVce” (Parameter With Voice) parameter to “on” for a certain Part then reselect the same Voice. The settings of some Voice Common parameters will be applied to the Performance Part. [PERFORM]  [EDIT]  Number [1] – [4]  [F1] VOICE  [SF1] VOICE  “P.WithVce” 2. Execute the Voice Copy Job in the Performance Job mode. This Job copies the System Effect, Master Effect and Master EQ settings in the Voice mode to the Performance Common parameters. [PERFORM]  [JOB]  [F3] COPY  [SF2] VOICE 3. Set the Reverb Send Level and Chorus Send Level to the desired value (same as in the Voice mode) manually. [PERFORM]  [EDIT]  Part selection  [F2] OUTPUT  [SF2] EF SEND The Song/Pattern cannot be started even when pressing the [F] (Play) button.  Does the selected Song or Pattern (phrase) actually contain data?  Is the [DAW REMOTE] button turned on?  Is the MIDI Sync parameter set to “internal” or “auto” (using internal clock)? [UTILITY]  [F5] MIDI  [SF3] SYNC  “MIDI Sync” = “auto” or “internal” 68 MOXF6/MOXF8 Owner’s Manual Appendix Song/Pattern (Phrase) cannot be recorded.  Is there enough free memory for recording? The total memory capacity determines the number of Songs/Patterns (phrases) that can be recorded. For example, if the memory contains Songs/Patterns (phrases) that use up a large amount of memory, the memory may become full even though the available Pattern or Song numbers are not all used. Cannot enter the Pattern Job mode/Pattern Mixing mode even when pressing the [JOB] button in the Pattern mode.  Check whether the instrument is in the Pattern Chain mode or not. If so, exit from the Pattern Chain mode, then press the [JOB] button or [MIXING] button. The drum sound is wrong or unexpected when changing the transpose value in the Song/Pattern Play mode.  This is normal. Changing the transpose setting while playing a Drum Voice will produce different sounds for the same keys played. Data communication between the computer and this instrument does not work properly.  Check whether the Port settings on the computer are appropriate or not.  Check whether or not the MIDI IN/OUT parameter is set to the appropriate value. [UTILITY]  [F6] MIDI  [SF4] OTHER  “MIDI IN/OUT”  This problem may be solved by reducing the computer load. To do this, set the USB Audio Output Channel to “2ch” in the following display. If the setting is changed in the display, press the [ENTER] button and then restart the instrument. [UTILITY]  [F5] USB I/O  [SF1] OUT CH The sound is not produced properly even when playing back the Song data on the computer or the MIDI instrument connected to this instrument.  Make sure to set this instrument to the Song mode or Pattern mode. The Voice mode or Performance mode may not produce the proper sound even when playing back Song data on the MIDI instrument or the computer connected to this instrument. MIDI bulk data transmission/reception does not work properly.  Is the Receive Bulk parameter set to on? [UTILITY]  [F6] MIDI  [SF2] SWITCH  “RcvBulk”  When receiving MIDI bulk data transmitted via the Bulk Dump function and recorded to the external MIDI device, you need to set the MIDI Device Number to the same value as when transmitting. [UTILITY]  [F5] MIDI  [SF1] CH  “DeviceNo”  When transmission does not work properly, is the device number of the MIDI instrument connected to this instrument set to match the Device Number Parameter in the Utility mode? [UTILITY]  [F5] MIDI  [SF1] CH  “DeviceNo” Cannot save data to the external USB flash memory device  Is the USB flash memory device being used write protected? (Write-protect should be set to off for saving data.)  Is the USB flash memory device being used properly formatted? [FILE]  [F1] CONFIG  [SF2] FORMAT Cannot enter the Edit mode  Is Category Search turned on? Turn off Category Search then press the [EDIT] button. MOXF6/MOXF8 Owner’s Manual 69 Appendix Installing Optional Hardware Installation Precautions Available devices • Before beginning installation, switch off the power to the instrument and connected peripherals, and unplug them from the power outlet. Installation or removal of any devices should be started ONLY after the instrument (and any optional hardware) returns to normal room temperature. Then remove all cables connecting the instrument to other devices. (Leaving the power cord connected while working can result in electric shock. Leaving other cables connected can interfere with work.) Before installing the optional hardware, make sure you have a Phillips screwdriver and ample space to work. WARNING The following optional devices can be installed to the MOXF. FL512M/FL1024M (Flash memory expansion module) • Be careful not to drop any screws inside the instrument during installation. (This can be prevented by keeping the optional units and cover away from the instrument while attaching). If this does happen, be sure to remove the screw(s) from inside the unit before turning the power on. Loose screws inside the instrument can cause improper operation or serious damage. If you are unable to retrieve a dropped screw, consult your Yamaha dealer for advice. Installation locations MOXF6 • Install the optional units carefully as described in the procedure below. Improper installation can cause shorts which may result in irreparable damage and pose a fire hazard. • Do not disassemble, modify, or apply excessive force to board areas and connectors on optional units. Bending or tampering with boards and connectors may lead to electric shock, fire, or equipment failures. CAUTION Bottom cover for the FL512M/FL1024M MOXF8 • It is recommended that you wear gloves to protect your hands from metallic projections on optional units and other components. Touching leads or connectors with bare hands may cause finger cuts, and may also result in poor electrical contact or electrostatic damage. • Be careful of static electricity. Static electricity discharge can damage the IC chips. Before you handle the optional units, to reduce the possibility of static electricity, touch unpainted metal parts or a ground wire on a device that is grounded. Bottom cover for the FL512M/FL1024M • Handle the optical units with care. Dropping or subjecting them to any kind of shock may cause damage or result in a malfunction. • Do not touch the exposed metal parts in the circuit board. Touching these parts may result in a faulty contact. • Be careful not to misplace any of the screws. • Do not use any screws other than what are installed on the instrument. Use of incorrect screws can cause damage. 70 MOXF6/MOXF8 Owner’s Manual Appendix Installing Optional Hardware FL512M/FL1024M 3 Remove the cover from the bottom. With the rear panel of the MOXF facing you, remove the screws from the cover by using the Phillips screwdriver. After removing the screws, slide the cover away to remove it. Configuration There are two types of the Flash Memory Expansion Module: Important Keep the removed screws in a safe place. They will be used when reattaching the cover to the instrument after installation.  FL512M Features a memory size of 512 MB.  FL1024M  Rear side Features a memory size of 1024 MB. Installation Procedure 1 2 Turn the power of the MOXF off, and disconnect the AC power cord. Also, make sure to disconnect the MOXF from any connected external devices. Turn the MOXF upside down so that the keyboard faces down and you have direct access to the underside of the instrument. Bottom 4 Attach the FL1024M or FL512M to the slot. As shown below. To protect the Knobs, Wheels and Sliders from damage, place the keyboard so the four corners are supported by something that provides sufficient support like magazines or cushions. Place supports at all four corners, taking care not to touch the Knobs, Wheels and Sliders.  Rear side Location for FL512M/ FL1024M Female screws Slot Attach the module to the slot via the following steps. View of the keyboard from the bottom 4-1 Insert the Module vertically in the slot and align the screws (on the Module) to the female screws respectively. Place supports at all four corners, taking care not to touch the Knobs, Wheels and Sliders. CAUTION FL512M/ FL1024M  Rear side • Since the instrument—particularly the MOXF8—is very heavy, this procedure should not be done alone, but by two or three people. Slot Female screws MOXF6/MOXF8 Owner’s Manual 71 Appendix 4-2 Press the top of the connector as shown, then push the Removing the Module connector firmly into the slot. 1 Loosen both the screws. Press this section lightly but firmly Serial No. seal 4-3 Tighten each screw of the Memory Module to each female screw of the MOXF with your hand as shown below. NOTICE • If you cannot loosen the screw with your hand, use a Phillips screwdriver. In this case, be careful NOT to scratch the circuit board of the FL512M/FL1024M and MOXF. • Since the screws can be removed from the module, be careful NOT to drop them inside the instrument when loosening them. 2 Pull out the FL512M/FL1024M vertically. 3 Attach the cover to the bottom panel. Position the cover on the bottom panel aligning the screws with the screw holes, then tighten the screws with a Phillips 5 Re-install the cover you removed in step 3, in reverse order. 6 Check that the installed Module or Modules are functioning properly. 6-1 screwdriver to fix the cover.  Rear side Turn the MOXF right side up again so that the keyboard faces up then turn the power on. While launching, you will see a message indicating that the Flash Memory Module cannot be recognized. 6-2 Press the [FILE] button to enter the File mode then press the [F6] FLASH button. 6-3 Press the [SF1] Format button. 6-4 Press the [ENTER] button to execute the Format operation. 6-5 Check whether the Total size shown on the display is correct or not. 72 MOXF6/MOXF8 Owner’s Manual Bottom Appendix Specifications Keyboards MOXF8 88 keys, GHS keyboard (Initial Touch) MOXF6 61 keys, semi-weighted keyboard (Initial Touch) Tone Generator Tone Generator block Polyphony Multi-timbral Capacity Sequencer block AWM2, with Expanded Articulation 128 notes 16 parts (Internal), A/D input part Wave 741MB (when converted to 16-bit linear format), 3,977 waveforms Voice Preset: 1,152 Normal Voices + 72 Drum Kits GM: 128 Normal Voices + 1 Drum Kit User: 384 Normal Voices + 32 Drum Kits Performance User: 256 (up to 4 parts) Filter 18 types Effect System Reverb x 9 types, Chorus x 22 types, Insertion (A, B) x 54 types x 8 parts, Vocoder x 1 (uses both Insertion Effect A and B blocks), Master Effect x 9 types, Master EQ (5 bands), Part EQ (3 bands, stereo) Note Capacity Approx. 226,000 notes Note Resolution 480 ppq (parts per quarter note) Maximum Polyphony 124 notes Tempo (BPM) 5 – 300 Recording type Real time replace, Real time overdub (with the exception of the Pattern Chain), Real time punch in/out (Song only), Step (with the exception of the Pattern Chain) Tracks Song: 16 sequence Tracks (Loop on/off can be set for each Track), Tempo Track, Scene Track Pattern: 16 Phrase Tracks Pattern Chain: Pattern Track, Tempo Track, Scene Track Songs 64 Songs Mixing Voices: 16 Voices per Song/Pattern (up to 256 Voices) Mixing Templates: 32 for all Songs and Patterns Scene Memory 6 per Song Patterns 64 Patterns (x 16 sections) Measures: 256 maximum Phrases User Phrases: 256 per Pattern Arpeggio Preset: 7,981 types User: 256 types (MIDI Sync, MIDI transmit/receive channel, Velocity Limit, and Note Limit can be set. 4 Arpeggio parts can be played simultaneously.) Others Sequence Format Original format, SMF format 0, 1 (Format 1 load only) Master User:128 Sequence Software compatible with the Remote Control function For Windows®: Cubase 7 series, SONAR X2 For Mac®: Cubase 7 series, Logic Pro 9, Digital Performer 7 Controllers Pitch Bend wheel, Modulation wheel, Assignable Knob x 8, [DATA] dial x 1, Assignable Function buttons x 2 Display 240 x 64 dot, backlit LCD Connectors OUTPUT [L/MONO]/[R] (standard phone jack), A/D INPUT [L]/[R] (standard phone jack), [PHONES] (standard stereo phone jack), [FOOT CONTROLLER], FOOT SWITCH [ASSIGNABLE]/[SUSTAIN], MIDI [IN]/[OUT]/[THRU], USB [TO HOST]/[TO DEVICE], DC IN Power Consumption 13W Dimensions, Weight MOXF8: 1320 (W) x 405 (D) x 168 (H) mm, 14.9 kg MOXF6: 1030 (W) x 358 (D) x 125 (H) mm, 7.1 kg Accessories AC adaptor (PA-150 or an equivalent recommended by Yamaha), USB cable, Owner’s Manual (this book), Online Manual CD-ROM x 1 (containing Reference Manual, Synthesizer Parameter Manual, and Data List), CUBASE AI DOWNLOAD INFORMATION Optional Memory Module FL512M/FL1024M x 1 (Each master includes Master keyboard settings with 4 Zones, Assignable Knob settings, Program Change table.) (Functions to be controlled differ depending on the software.) Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. MOXF6/MOXF8 Owner’s Manual 73 Appendix Index A FL512M/FL1024M ....................................................................70 A/D INPUT [GAIN] knob ......................................................... 12 Flash Memory Expansion Module ...........................................70 A/D INPUT [L] and [R] jacks ............................................. 16, 38 [FOOT CONTROLLER] jack ....................................................16 A/D INPUT [ON/OFF] button ................................................... 12 FOOT SWITCH [ASSIGNABLE]/[SUSTAIN] jacks ...................16 ARP [EDIT] button ............................................................. 13, 31 Format .....................................................................................61 ARP [ON/OFF] button ....................................................... 13, 27 Arpeggio ........................................................................... 27, 34 G ASSIGNABLE FUNCTION [1]/[2] buttons ............................... 12 GM Bank ..................................................................................25 Audio channels ....................................................................... 54 GM Voice .................................................................................25 audio equipment ..................................................................... 38 Group [A] – [H] buttons ...........................................................14 B H BANK SELECT [DEC]/[INC] buttons ....................................... 14 Headphones ............................................................................17 C I [CATEGORY SEARCH] button .......................................... 14, 26 [INC] button .......................................................................14, 21 CHAR ...................................................................................... 22 Click ........................................................................................ 59 [COMMON] button .................................................................. 14 Common Edit .......................................................................... 29 Compare function ................................................................... 29 Connect (Computer) ............................................................... 53 Connect (External MIDI Instrument) ....................................... 51 Cubase ....................................................................... 56, 57, 73 Cursor buttons .................................................................. 14, 21 K Key Edit ...................................................................................29 Keyboard .................................................................................12 Knob Function button ........................................................12, 28 KNOB FUNCTION pop-up window .........................................28 Knobs ................................................................................12, 28 L Layer .......................................................................................31 D [DATA] dial ....................................................................... 14, 21 [DAW LEVEL] slider ................................................................ 12 [DAW REMOTE] button ..................................................... 13, 55 DAW software ......................................................................... 54 DC IN connector ..................................................................... 16 [DEC] button ..................................................................... 14, 21 Demo Pattern .......................................................................... 47 Demo Song ............................................................................. 19 Digital Performer ............................................................... 56, 73 Display Messages .................................................................. 63 Drum Assign ........................................................................... 33 [DRUM ASSIGN] button .......................................................... 14 Drum Voice ............................................................................. 25 [LAYER] button ........................................................................14 LCD .........................................................................................13 LCD status ...............................................................................59 [LEVEL] meter .........................................................................12 [LEVEL] meter button ..............................................................12 Load ........................................................................................60 Logic Pro ...........................................................................56, 73 M Master Effect ...........................................................................59 Master EQ ................................................................................59 Master mode ...........................................................................57 MASTER VOLUME .............................................................12, 18 microphone .............................................................................38 MIDI [IN] / [OUT] / [THRU] terminals .......................................16 E MIDI channels .........................................................................54 Edit Indicator ........................................................................... 28 MIDI ports ................................................................................54 Effect ................................................................................. 29, 59 EFFECT buttons ...................................................................... 13 Element Edit ............................................................................ 29 [ENTER] button ....................................................................... 14 [EXIT] button ........................................................................... 14 MIDI Receive Channel .............................................................52 MIDI Transmit Channel ............................................................52 Mixing ................................................................................40, 45 Mixing template .......................................................................46 [MODE] buttons .......................................................................14 Modes ......................................................................................23 F Modulation wheel ....................................................................12 [F1] – [F6] (Function) buttons ........................................... 13, 21 MOXF6/MOXF8 Editor .............................................................57 Factory Settings ...................................................................... 20 Mute ..................................................................................34, 41 [FAVORITE] button ........................................................... 14, 26 [MUTE] button .........................................................................15 Favorite Category ................................................................... 26 File Mode ................................................................................ 60 74 MOXF6/MOXF8 Owner’s Manual Appendix N T Naming ................................................................................... 22 Track .......................................................................................40 Normal Voice .......................................................................... 25 [TRACK] button .......................................................................15 NUM ........................................................................................ 21 TRANSPOSE [-] and [+] buttons .......................................13, 27 Number [1] – [16] buttons ...................................................... 15 Troubleshooting .......................................................................65 O U OCTAVE [-] and [+] buttons ............................................. 12, 27 USB [TO DEVICE] terminal ......................................................61 OUTPUT [L/MONO] and [R] jacks .......................................... 16 USB [TO HOST] terminal .........................................................53 USB flash memory device .................................................60, 61 P USB terminals ..........................................................................16 Part .......................................................................................... 34 User Banks ..............................................................................25 Pattern ..................................................................................... 36 User Phrase .......................................................................48, 49 Pattern Chain .......................................................................... 49 Utility mode ..............................................................................58 Pattern mode .......................................................................... 47 Pattern Patch display .............................................................. 49 V Pattern Play ............................................................................. 47 Vocoder ...................................................................................39 [PATTERN SECTION/PERFORMANCE CONTROL] button .... 15 Voice Edit ................................................................................28 Performance Creator ........................................................ 14, 31 Voice mode .............................................................................25 Performance Edit .................................................................... 35 Voice Play ................................................................................25 Performance Mode ................................................................. 34 Performance Play .................................................................... 34 Y [PHONES] (Headphone) jack ................................................. 16 Yamaha Steinberg USB Driver ................................................53 Pitch Bend wheel .................................................................... 12 Power On Mode ...................................................................... 58 Power supply .......................................................................... 17 Preset Banks ........................................................................... 25 Punch In/Out ........................................................................... 43 Q Quick Setup ............................................................................ 54 R Realtime Recording .......................................................... 40, 43 Record (Pattern) ..................................................................... 47 Record (Performance) ............................................................ 36 Record (Song) ........................................................................ 41 Remote Control ....................................................................... 55 S Save ........................................................................................ 60 Section .................................................................................... 38 Section Length ........................................................................ 38 SEQ TRANSPORT button .................................................. 13, 19 [SF1] – [SF6] (Sub Function) buttons ............................... 13, 21 [SHIFT] button ......................................................................... 14 Shift Function List .................................................................... 62 Solo ................................................................................... 34, 41 [SOLO] button ......................................................................... 15 SONAR .............................................................................. 56, 73 Song ........................................................................................ 36 Song mode ............................................................................. 40 Speaker ................................................................................... 17 Split ......................................................................................... 32 [SPLIT] button ......................................................................... 14 Standby/On switch .................................................................. 16 Step Recording ................................................................. 40, 41 Store .................................................................................. 29, 46 MOXF6/MOXF8 Owner’s Manual 75 Memo 76 MOXF6/MOXF8 Owner’s Manual Memo MOXF6/MOXF8 Owner’s Manual 77 For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A. Tel: 714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México, S.A. de C.V. Av. Insurgentes Sur 1647 “Prisma Insurgentes”, Col. San Jose Insurgentes, Del. Benito Juarez, 03900, Mexico, D.F. Tel: 55-5804-0600 BRAZIL Yamaha Musical do Brasil Ltda. Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi, CEP 04534-013 São Paulo, SP. BRAZIL Tel: 011-3704-1377 ARGENTINA Yamaha Music Latin America, S.A., Sucursal Argentina Olga Cossettini 1553, Piso 4 Norte, Madero Este-C1107CEK Buenos Aires, Argentina Tel: 54-11-4119-7000 VENEZUELA Yamaha Music Latin America, S.A., Sucursal Venezuela C.C. Manzanares Plaza P4 Ofic. 0401- Manzanares-Baruta Caracas Venezuela Tel: 58-212-943-1877 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Torre Banco General, Piso No.7, Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, República de Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM/IRELAND Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, U.K. Tel: 01908-366700 GERMANY Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 SWITZERLAND/LIECHTENSTEIN Yamaha Music Europe GmbH Branch Switzerland in Zürich Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: 044-387-8080 AUSTRIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 CZECH REPUBLIC/HUNGARY/ ROMANIA/SLOVAKIA/SLOVENIA Yamaha Music Europe GmbH Branch Austria (Central Eastern Europe Office) Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 POLAND/LITHUANIA/LATVIA/ESTONIA Yamaha Music Europe GmbH Branch Poland Office ul. Wrotkowa 14 02-553 Warsaw, Poland Tel: 022-500-2925 BULGARIA Dinacord Bulgaria LTD. Bul.Iskarsko Schose 7 Targowski Zentar Ewropa 1528 Sofia, Bulgaria Tel: 02-978-20-25 MALTA Olimpus Music Ltd. The Emporium, Level 3, St. Louis Street Msida MSD06 Tel: 02133-2144 DMI7 Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NETHERLANDS/BELGIUM/ LUXEMBOURG Yamaha Music Europe Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, Netherlands Tel: 0347-358 040 FRANCE Yamaha Music Europe 7 rue Ambroise Croizat, Zone d'activites Pariest, 77183 Croissy-Beaubourg, France Tel: 01-64-61-4000 ITALY Yamaha Music Europe GmbH, Branch Italy Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 SPAIN/PORTUGAL Yamaha Music Europe GmbH Ibérica, Sucursal en España Ctra. de la Coruna km. 17,200, 28231 Las Rozas (Madrid), Spain Tel: +34-91-639-88-88 GREECE Philippos Nakas S.A. The Music House 147 Skiathou Street, 112-55 Athens, Greece Tel: 01-228 2160 SWEDEN Yamaha Music Europe GmbH Germany filial Scandinavia J. A. Wettergrensgata 1, Box 30053 S-400 43 Göteborg, Sweden Tel: +46 31 89 34 00 DENMARK Yamaha Music Europe GmbH, Tyskland – filial Denmark Generatorvej 6A, DK-2730 Herlev, Denmark Tel: 44 92 49 00 FINLAND F-Musiikki Oy Kluuvikatu 6, P.O. Box 260, SF-00101 Helsinki, Finland Tel: 09 618511 NORWAY Yamaha Music Europe GmbH Germany Norwegian Branch Grini Næringspark 1, N-1361 Østerås, Norway Tel: 67 16 78 00 ICELAND Skifan HF Skeifan 17 P.O. Box 8120, IS-128 Reykjavik, Iceland Tel: 525 5000 RUSSIA Yamaha Music (Russia) LLC. Room 37, bld. 7, Kievskaya street, Moscow, 121059, Russia Tel: 495 626 5005 OTHER EUROPEAN COUNTRIES Yamaha Music Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 AFRICA SOUTH AFRICA Global Music Instruments Unit 4, 130 Boeing Road East Bedfordview 2008 Postnet Suite 130, Private Bag X10020 Edenvale 1610, South Africa Tel: 27-11-454-1131 OTHER AFRICAN COUNTRIES Yamaha Music Gulf FZE LOB 16-513, P.O.Box 17328, Jebel Ali, Dubai, United Arab Emirates Tel: +971-4-881-5868 MIDDLE EAST TURKEY/CYPRUS Yamaha Music Europe GmbH Merkezi Almanya Türkiye İstanbul Şubesi Maslak Meydan Sokak No:5 Spring Giz Plaza Bağımsız Böl. No:3, 34398 Şişli, İstanbul Tel: +90-212-999-8010 OTHER COUNTRIES Yamaha Music Gulf FZE LOB 16-513, P.O.Box 17328, Jebel Ali, Dubai, United Arab Emirates Tel: +971-4-881-5868 ASIA THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 HONG KONG Tom Lee Music Co., Ltd. 11/F., Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688 INDIA Yamaha Music India Pvt. Ltd. Spazedge building, Ground Floor, Tower A, Sector 47, Gurgaon- Sohna Road, Gurgaon, Haryana, India Tel: 0124-485-3300 INDONESIA PT. Yamaha Musik Indonesia (Distributor) Yamaha Music Center Bldg. Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 021-520-2577 KOREA Yamaha Music Korea Ltd. 8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong, Kangnam-Gu, Seoul, Korea Tel: 02-3467-3300 MALAYSIA Yamaha Music (Malaysia) Sdn., Bhd. No.8, Jalan Perbandaran, Kelana Jaya, 47301 Petaling Jaya, Selangor, Malaysia Tel: 03-78030900 PHILIPPINES Yupangco Music Corporation 339 Gil J. Puyat Avenue, P.O. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 SINGAPORE Yamaha Music (Asia) Private Limited Block 202 Hougang Street 21, #02-00, Singapore 530202, Singapore Tel: 65-6747-4374 TAIWAN Yamaha Music & Electronics Taiwan Co.,Ltd. 3F, No.6, Section 2 Nan-Jing East Road, Taipei, Taiwan R.O.C. Tel: 02-2511-8688 THAILAND Siam Music Yamaha Co., Ltd. 3, 4, 15 and 16th floor, Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: 02-215-2622 VIETNAM Yamaha Music Vietnam Company Limited 15th Floor, Nam A Bank Tower, 201-203 Cach Mang Thang Tam St., Ward 4, Dist.3, Ho Chi Minh City, Vietnam Tel: +84-8-3818-1122 OTHER ASIAN COUNTRIES Yamaha Corporation Market Development Section Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 NEW ZEALAND Music Works LTD P.O.BOX 6246 Wellesley, Auckland 4680, New Zealand Tel: 9-634-0099 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation Market Development Section Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 Yamaha Web Site (English) http://www.yamahasynth.com/ Yamaha Downloads http://download.yamaha.com/ C.S.G., Digital Musical Instruments Division © 2013 Yamaha Corporation 305MWTY*.*-**A0 Printed in China ZG45700 ZG45700