Yamaha RX-V496RDS de handleiding

Merk: Yamaha

Model: RX-V496RDS

Categorie: AV-ontvangers

Type: de handleiding

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

RX-V496RDS

Natural Sound AV Receiver

Ampli-tuner audio-vidéo

RX-V496RDS

G B

1/17/0, 6:25 PM

CAUTION

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2. Install this unit in a cool, dry, clean place — away

from windows, heat sources, sources of excessive

vibration, dust, moisture and cold. Avoid sources of

humming (transformers, motors). To prevent fire or

electrical shock, do not expose the unit to rain or

water.

3. Never open the cabinet. If something drops into the

unit, contact your dealer.

4. Do not use force on switches, controls or connection

wires. When moving the unit, first disconnect the

power cord and then the wires connected to other

component. Never pull the wires themselves.

5. The openings on the cover assure proper ventilation

of the unit. If these openings are obstructed, the

temperature inside the unit will rise rapidly.

Therefore, avoid placing objects against these

openings, and install the unit in a well-ventilated area

to prevent fire and damage.

Be sure to allow a space of at least 20 cm behind,

20 cm on both sides and 30 cm above the top panel

of the unit to prevent fire and damage.

6. The voltage used must be the same as that specified

on this unit. Using this unit with a higher voltage than

specified is dangerous and may result in fire or other

accidents. YAMAHA will not be held responsible for

any damage resulting from the use of this unit with a

voltage other than that specified.

7. Digital signals generated by this unit may interfere

with other component such as tuners, receivers and

TVs. Move this unit farther away from such

component if interference is observed.

8. Always set VOLUME to the “m” position before

starting the audio source play. Increase the volume

gradually to an appropriate level after playback has

been started.

9. Do not attempt to clean the unit with chemical

solvents; this might damage the finish. Use a clean,

dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before

concluding that the unit is faulty.

11. When not planning to use this unit for a long period

of time (e.g., a vacation), disconnect the AC power

cord from the wall outlet.

12. To prevent lightning damage, disconnect the AC

power cord and disconnect the antenna cable when

there is an electrical storm.

13. Grounding or polarization — Precautions should be

taken so that the grounding or polarization of the unit

is not defeated.

14. AC outlet — Do not connect audio component to the

AC outlet on the rear panel if that component

requires more power than the outlet is rated to

provide.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off. This state is called the standby

mode. In this state, this unit is designed to consume a

very small quantity of power.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug, proceed

as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured BROWN

must be connected to the terminal which is marked with

the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

0101V496RDS_caution_EN 1/6/0, 10:19 AM2

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

FEATURES

5-Channel Power Amplification

◆ Minimum RMS Output

(0.06% THD, 20 Hz – 20 kHz)

Main: 65 W + 65 W (8 Ω)

Center: 65 W (8 Ω)

Rear: 65 W + 65 W (8 Ω)

Multi-mode Digital Sound Field

Processing

◆ Digital Sound Field Processor (DSP)

◆ Dolby Digital Decoder

◆ Dolby Pro Logic Decoder

◆ DTS Decoder

◆ CINEMA DSP: Theater-like Sound Experience by

the Combination of YAMAHA DSP Technology

and Dolby Digital, Dolby Pro Logic or DTS

◆ Automatic Input Balance Control for Dolby Pro

Logic decoding

Sophisticated FM/AM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset Editing)

◆ Multi-Functions for RDS Broadcast Reception

Other Features

◆ “SET MENU” which Provides You with 11 Items

for Optimizing This Unit for Your Audio/Video

System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other Future

Formats

◆ Video Signal Input/Output Capability

(Including S Video Connections)

◆ 2 Optical/1 Coaxial Digital Signal Input Terminals

◆ SLEEP Timer

◆ Remote Control with Preset Manufacturer Codes

INTRODUCTION

CONTENTS

PREPARATION

SPEAKER SETUP....................................................... 8

CONNECTIONS.......................................................... 9

ADJUSTING THE SPEAKER BALANCE ............ 18

BASIC OPERATION

PLAYING A SOURCE .............................................. 20

DIGITAL SOUND FIELD PROCESSOR (DSP)

EFFECT .................................................................. 24

SOUND FIELD PROGRAM .................................... 25

TUNING ..................................................................... 28

RECEIVING RDS STATIONS................................. 32

RECORDING A SOURCE ON TAPE, MD OR

VIDEO CASSETTE ............................................... 35

ADVANCED OPERATION

SET MENU................................................................. 36

DELAY TIME AND SPEAKER

OUTPUT LEVELS ................................................. 40

SLEEP TIMER .......................................................... 42

PRESET REMOTE CONTROL .............................. 43

APPENDIX

TROUBLESHOOTING ............................................ 50

SPECIFICATIONS.................................................... 53

GLOSSARY................................................................ 54

INDEX ........................................................................ 55

INTRODUCTION

FEATURES .................................................................. 1

CONTENTS ................................................................. 1

GETTING STARTED ................................................. 2

CONTROLS AND FUNCTIONS ............................... 4

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic” and the

double-D symbol are trademarks of Dolby

Laboratories. Confidential Unpublished Works.

rights reserved.

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued and

pending. “DTS”, “DTS Digital Surround”, are trademarks of

y indicates a tip for your operation.

0102V496RDS01-07_EN 1/6/0, 10:19 AM1

GETTING STARTED

Checking the Package Contents

Check that the following items are included in your package.

Remote control Batteries (AAA, R03, UM-4 type) 75-ohm/300-ohm antenna adapter

(U.K. model only)

Indoor FM antenna

AM loop antenna

Battery Installation in the Remote

Control

1 Turn the remote control over and slide the

battery compartment cover in the direction of

the arrow.

2 Insert the batteries (AAA, R03 or UM-4 type)

according the polarity markings on the inside

of the battery compartment.

3 Close the battery compartment cover.

Battery Replacement

If the remote control operates only when it is close to the

unit, the batteries are weak. Replace all the batteries with

new ones.

Be sure to replace the batteries within about two minutes.

If it takes longer than two minutes, the codes preset for

the remote control will return to the factory settings.

(Refer to pages 43 to 49 about the remote control.)

Notes

• Use only AAA, R03 or UM-4 batteries for replacement.

• Be sure the battery polarity is correct. (See the illustration inside

the battery compartment.)

• Remove the batteries if the remote control will not be used for an

extended period of time.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

Quick reference card

Connection guide

0102V496RDS01-07_EN 1/6/0, 10:19 AM2

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

Using the Remote Control

The remote control transmits a directional infrared beam. Be

sure to aim the remote control directly at the infrared sensor

during operation. When the sensor is covered or there is a

large object between the remote control and the sensor, the

sensor cannot receive signals. The sensor may not be able to

receive signals properly when it is exposed to direct sunlight

or a strong artificial light (such as a fluorescent or strobe

light). In this case, change the direction of the light or

reposition the unit to avoid direct lighting.

Notes

• Handle the remote control with care.

• Do not spill water, tea or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following

conditions:

– high humidity or temperature such as near a heater, stove or

bath;

– dusty places; or

– extremely low temperature.

GETTING STARTED

Remote control

sensor

Within approximately 6 m

(20 feet)

0102V496RDS01-07_EN 1/6/0, 10:19 AM3

–

12 3 4 65

7890qwerty

uiopasdf

6VOLUME

Turn this control to turn up or down the volume.

7 PHONES jack

Connect the headphones to the PHONES jack. You can

listen to the sound to be output from the main speakers

through the headphones.

When using headphones only, set both SPEAKERS A and B

to the OFF position and press EFFECT to turn off the effect

speakers (center and rear) (so that no DSP program name

appear on the display).

8 SPEAKERS

Set A or B (or both A and B) to the ON position for the main

speaker system (connected to this unit) that you want to use.

Set the button(s) to the OFF position for the main speaker

system that you don’t want to use.

9 PROGRAM selector

Press l or h to select a DSP program when the effect

speakers (center and rear) are turned on. The name of the

selected program appears on the display.

0 EFFECT

Press this button to turn on or off the effect speakers (center

and rear). If you turn them off, all Dolby Digital and DTS

audio signals are directed to the right and left main

speakers. In that case, the output levels of the right and left

speakers may not match.

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Press this switch to turn on the power of this unit or to set

this unit in the standby mode. Before turning the power on,

set VOLUME to the “m” position.

Standby mode

In this mode, this unit consumes a very small quantity of

power to receive infrared-signals from the remote

control.

2 Remote control sensor

This receives signals from the remote control.

3 Display

This shows various information. (Refer to page 6 for

details.)

4 INPUT MODE

Press this button to select the input mode among AUTO,

DTS and ANALOG for the DVD/LD, TV/digital TV and

satellite tuner sources.

5 INPUT SELECTOR

Turn this selector to select the input source (TUNER, CD,

PHONO, V-AUX, VCR, SAT/D-TV, DVD/LD) that you

want to listen to or watch. The arrow for the selected input

source indicator lights up on the display.

0102V496RDS01-07_EN 1/19/0, 10:26 AM4

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

q Tone controls

These controls are only effective for the sound from the

main speakers.

a) BASS

Turn this control clockwise to increase or counterclockwise

to decrease the low-frequency response. The “0” position

produces a flat response.

b) TREBLE

Turn this control clockwise to increase or counterclockwise

to decrease the high-frequency response. The “0” position

produces a flat response.

w TAPE/MD MON / EXT. DECODER

Press this button to select a tape or an MD source. The

“TAPE/MD MONITOR” indicator lights up on the display.

When you press the button next, the “TAPE/MD

MONITOR” indicator goes off, “EXT. DECODER” appears

on the display and you can listen to a source connected to

the EXTERNAL DECODER INPUT terminals.

e BALANCE

This control is only effective for the sound from the main

speakers.

Turn the control to adjust the balance of the output volume

from the right and left main speakers to compensate for

sound imbalance caused by the speaker location or listening

room conditions.

r A/B/C/D/E

Press this button to select one of a group (A to E) of preset

stations.

t PRESET/TUNING

When “ z ” appears

This button is used to select a preset station number (1 to 8).

Press h to select a higher and l to select a lower preset

station number.

When “ z ” goes off

This button is used for tuning. Press h to tune in to higher

frequencies, and l to tune in to lower frequencies.

When this unit is in the PTY SEEK mode, press this button

to select a program type.

y PRESET/TUNING, EDIT

Press this button to turn on or off “ z ” on the display and

switch the function between for storing a broadcasting

station (preset tuning) and for tuning. This button is also

used to exchange the assignment of two preset stations with

each other.

u FM/AM

Press this button to switch the reception band between FM

and AM.

i MEMORY (MAN’L/AUTO FM)

Press this button to store the broadcasting stations. Hold

down this button for more than three seconds to begin

automatic preset tuning.

o TUNING MODE (AUTO/MAN’L MONO)

Press this button to switch the tuning mode between

automatic and manual. To use the automatic tuning method,

press this button so that the “AUTO” indicator lights up on

the display. To use the manual tuning method, press this

button so that the “AUTO” indicator goes off.

p RDS MODE/FREQ

When an RDS station is received, press this button to

change the display mode among the PS mode, PTY mode,

RT mode, CT mode (if the station offers those RDS data

services) and/or frequency display mode in turn.

a EON

Press this button to select the desired program type (NEWS,

INFO, AFFAIRS, SPORT) when you want to tune in to a

radio program of that type automatically.

s PTY SEEK MODE

Press this button to set the unit in the PTY SEEK mode.

d PTY SEEK START

Press this button to begin searching for a station after the

desired program type has been selected in the PTY SEEK

mode.

f VIDEO AUX terminals

Connect an auxiliary audio or video input source such as a

camcorder to these terminals. Use INPUT SELECTOR to

select the source connected to these terminals.

CONTROLS AND FUNCTIONS

0102V496RDS01-07_EN 1/6/0, 10:19 AM5

Display

8 MEMORY indicator

This flashes for about five seconds after pressing

MEMORY. During this period, the displayed station can be

stored in the memory.

9 RDS mode indicators

The name(s) of the RDS data offered by the currently

received RDS station light(s) up. Illumination of the red

indicator next to the RDS data name shows that the

corresponding RDS mode is now selected.

0 AUTO indicator

This lights up when the unit is in the automatic tuning

mode.

q PTY HOLD indicator

This lights up while searching for stations in the PTY SEEK

mode.

w EON indicator

This lights up when an RDS station that offers the EON data

service is being received.

e Program type name indicators

The name of the selected program type lights up when the

“EON” indicator lights up.

r STEREO indicator

This lights up when an FM stereo broadcast with sufficient

signal strength is being received.

t Signal-level indicator

This indicates the signal level of the station being received.

If multipath interference is detected, the indication

decreases.

y SLEEP indicator

This lights up while the built-in SLEEP timer is on.

CONTROLS AND FUNCTIONS

1 t indicator

The “t” indicator lights up when the built-in DTS

decoder is turned on.

2 DSP program indicators

The name of the selected DSP program lights up in the

following cases:

• When the tuner is selected as the input source.

• When DSP program No. 2, 3 or the subprogram

“ENHANCED” of No.1 is selected.

3 Multi-information display

This display shows various information: for example the

name of the selected DSP program and the various settings

during adjustment with the SET MENU. The current station

frequency and band (FM or AM) also appear when the tuner

is selected as the input source.

4 Input source indicators

One of the arrows for these indicators lights up depending

on which source is selected.

5 TAPE/MD MONITOR indicator

This lights up when the tape deck or MD recorder, etc. is

selected as the input source by pressing TAPE/MD MON /

EXT. DECODER (or TAPE/MD).

6 g and o indicators

“ g ” lights up when the built-in Dolby Digital

decoder is on and the signals of the selected source encoded

with Dolby Digital are not in 2-channel. “ o ”

lights up when the built-in Dolby Pro Logic decoder is on.

7 x indicator

“ x ” lights up when the built-in digital sound

field processor is on.

0102V496RDS01-07_EN 1/12/0, 10:26 AM6

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

Remote Control

1 Indicator

This flashes in red when pressing a button on the remote

control. If it flashes rapidly several times, press the selected

button again.

2 Component selector buttons

Press one of these buttons which corresponds to the

component you want to control with the remote control.

(The proper code must be set for your component. Refer to

“Setup codes” on page 48.) When the component selector

button has been pressed, the remote control is set to that

component operation mode.

3 POWER

Each time you press this button, the unit switches between

the power on and standby mode.

4 TEST

Press this button to output the test tone for each speaker.

5 A/B/C/D/E, PRESET +/–

These buttons are used to select a preset station.

A/B/C/D/E: To select one of a group (A to E) of preset

stations

PRESET +/–: To select a preset station number (1 to 8)

6 MUTE

Press this button to mute the sound. To cancel mute, press

this button again.

7 VOLUME

These buttons are used to adjust the volume level.

u: To turn up the volume

d: To turn down the volume

8 SLEEP

Press this button to set the SLEEP timer.

9 +/–

These buttons adjust the settings of the SET MENU and

TIME/LEVEL mode.

0 TIME/LEVEL

Press this button to select the items in the TIME/LEVEL

mode.

q Input selector buttons

These buttons select the input source.

CD: To play a CD

TUNER: To listen to an FM (RDS) or AM broadcast

TAPE/MD: To play a tape or MD

DVD/LD: To play a DVD or LD

SAT/D-TV: To watch a TV or satellite broadcast

VCR: To play a video cassette

PHONO: To play an analog record

V-AUX: To use a camcorder

EXT. DEC.: To play other multi-channel source

w EFFECT

Press this button to turn on or off the effect speakers (center

and rear).

e PRG+, PRG–

Press these buttons to select a DSP program.

r SET MENU

Press this button to select the items in the SET MENU.

CONTROLS AND FUNCTIONS

TV VOLUME

TV INPUT

Press AMP(TUNER).

This section describes basic operation of this unit with the

remote control. First, press AMP(TUNER) on the

component selector. Refer to “PRESET REMOTE

CONTROL” on page 43 for full details.

0102V496RDS01-07_EN 1/19/0, 10:26 AM7

SPEAKER SETUP

Speaker Placement

Refer to the following diagram when you place the

speakers.

Speakers to Be Used

This unit is designed to provide the best sound-field quality

with a 5-speaker system, using main speakers, rear speakers

and a center speaker. If you use different brands of speakers

(with different tonal qualities) in your system, the tone of a

moving human voice and other types of sound may not shift

smoothly. We recommend that you use speakers from the

same manufacture or speakers with the same tonal quality.

The main speakers are used for the main source sound plus

the effect sounds. They will probably be the speakers from

your present stereo system. The rear speakers are used for

the effect and surround sounds, and the center speaker is for

the center sounds (dialog, vocals, etc.). If for some reason it

is not practical to use a center speaker, you can do without

it. Best results, however, are obtained with the full system.

The main speakers should be high-performance models and

have enough power-handling capacity to accept the

maximum output of your audio system. The other speakers

do not have to be equal to the main speakers. For precise

sound localization, however, it is ideal to use high-

performance models that can reproduce sounds over the full

range for the center speaker and the rear speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is effective

not only for reinforcing bass frequencies from any or all

channels, but also for reproducing the LFE (low frequency

effect) channel with high fidelity when playing back a

source encoded with Dolby Digital or DTS. The YAMAHA

Active Servo Processing Subwoofer System is ideal for

natural and lively bass reproduction.

Main

speaker (L)

Center speaker

Main speaker (R)

Subwoofer

Rear speaker (L)

Rear speaker (R)

1.8 m

■ Main speakers

Place the right and left main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the TV monitor should be the

same.

■ Rear speakers

Place these speakers behind your listening position, facing

slightly inwards, nearly 1.8 m (approx. 6 feet) above the

floor.

■ Center speaker

Align the front face of the center speaker with the front face

of your TV monitor. Place the speaker as close to the

monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the sound will be heard from the

right and left main speakers. In that case, “CENTER SP” in the

SET MENU is set to the NONE position. (Refer to page 37 for

details.)

■ Subwoofer

The position of the subwoofer is not so critical, because low

bass sounds are not highly directional. But it is better to

place the subwoofer near the main speakers. Turn it slightly

toward the center of the room to reduce the wall reflections.

CAUTION

Some types of speakers interfere with a TV monitor. If

this problem occurs, move the speakers away from the

monitor. If you cannot avoid installing the center speaker

or subwoofer near the TV monitor, use magnetically

shielded speakers.

PREPARATION

0103V496RDS08-19_EN 1/6/0, 10:19 AM8

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been

completed.

Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some

components require different connection methods and have different terminal names. Refer to the instructions for each

component to be connected to this unit.

When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect

it to the terminals with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products.

Use RCA-type pin plug cables for connecting audio/video components with the exception described later.

The input and output terminals for pin plugs can be distinguished as follows:

Yellow video signals (composite)

White analog audio signals for the left channel

Red analog audio signals for the right channel

coaxial digital signals

After completing all connections, check them again to make sure they are correct.

MAINS

100W MAX. TOTAL

SWITCHED

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

REAR

(SURROUND)

CENTER

MAIN

––++

–

Connecting an Audio

Component (page 12)

Connecting a Video

Component (page 13)

IMPEDANCE SELECTOR

switch (page 17)

Connecting the

Antenna (page 10)

Connecting to an External

Decoder (page 14)

Connecting Speakers

(page 15)

Connecting the Power

Supply Cords (page 17)

(Europe model)

V V

C C

0103V496RDS08-19_EN 1/6/0, 10:19 AM9

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal

strength. However, a properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor

reception quality, an outdoor antenna may improve the quality.

Connect each antenna correctly to the designated terminals.

■ Indoor FM antenna (included)

Firmly insert the connector into the FM ANT terminal. The

indoor FM antenna is only a simple antenna. For reception

with better sound quality, installing the outdoor FM antenna

(commercially available) is recommended.

Note

• Do not connect an outdoor FM antenna and the indoor FM

antenna at the same time.

■ Outdoor FM antenna

You may be unable to obtain good FM radio reception

depending on your local conditions (distance from the

broadcasting station, interposing buildings and

mountains, etc.). Consult your dealer or authorized service

center and be sure to install an antenna that suits your local

conditions.

Install the outdoor FM antenna (commercially available) in

a high place as far away from any roads as possible to avoid

being affected by automobile ignition noise.

■ Connecting a coaxial cable to the included 75-ohm/300-ohm antenna

adapter (U.K. model only)

1 Open the cover of the included 75-ohm/

300-ohm antenna adapter.

2 Cut the external sleeve of the 75-ohm coaxial

cable and prepare it for connection.

3 Cut the lead wire and remove it.

4 Insert the cable wire into the slot, and clamp it

with pliers.

5 Snap the cover into place.

CONNECTIONS

75-ohm/300-ohm antenna

adapter (included for U.K.

model)

75-ohm coaxial cable

75-ohm/300-ohm antenna

adapter (included for U.K.

model)

300-ohm feeder

Unit: mm

(inch)

11 (7/16)

8 (5/16)

6 (1/14)

Lead wire

Insert the wire

into the slot.

Clamp with

pliers.

Clamp with

pliers.

Cover

Indoor FM

antenna

0103V496RDS08-19_EN 1/6/0, 10:20 AM10

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

■ AM loop antenna (included)

The AM loop antenna can be removed from the stand and

attached to a wall, etc. However, note that the reception

sensitivity may deteriorate if the antenna is attached to a

metal or steel reinforced wall.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

■ Connecting the AM loop antenna

1 Press the tab and unlock the terminal hole.

2 Insert the AM loop antenna lead wires into the

AM ANT and GND terminals.

3 Return the tab to its original position to lock

the lead wires. Lightly pull the lead wires to

confirm a good connection.

4 Attach the loop antenna to the antenna stand.

5 Orient the AM loop antenna so that the best

reception is obtained.

■ Outdoor AM antenna

If you cannot obtain good reception with the AM loop

antenna, connect 5 m to 10 m of vinyl covered wire to the

AM ANT terminal and extend it outdoors from a window.

■ Ground (GND terminal)

For maximum safety and minimum interference, connect

the antenna GND terminal to a good earth ground. A good

earth ground is a metal stake driven into moist earth.

CONNECTIONS

Antenna stand

AM loop antenna

Vinyl covered wire (5 m to 10 m)

0103V496RDS08-19_EN 1/6/0, 10:20 AM11

Connecting an Audio Component

■ PHONO terminals

These terminals are used to connect a turntable with an MM

or high-output MC cartridge. If you have a turntable with a

low-output MC cartridge, use an inline boosting transformer

or MC head amplifier when connecting to these terminals.

Connecting the ground (earth) wire of the turntable to the GND

terminal will normally minimize hum, but in some cases, better

results may be obtained with the ground wire disconnected.

CONNECTIONS

Be sure to connect the right channel (R), left channel (L),

input (IN) and output (OUT) properly.

Tape deck or

MD recorder

L R

L R L R

OUTPUT

OUTPUT LINE OUT LINE IN

GND

Turntable

(Europe model)

CD player

Analog signal

Signal flow

0103V496RDS08-19_EN 1/6/0, 10:20 AM12

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

Connecting a Video Component

■ Audio signal terminals

Be sure to connect the right channel (R), left channel (L),

input (IN) and output (OUT) properly.

■ Video signal terminals

Be sure to connect the input (IN) and output (OUT)

properly.

■ Digital audio signal terminals

If your DVD/LD player, TV/digital TV or satellite

tuner, etc. has coaxial or optical digital signal output

terminals, they can be connected to this unit’s COAXIAL

and/or OPTICAL digital signal input terminals. To make a

connection between the optical digital signal terminals,

remove the cover from each terminal, and then connect

them by using a commercially available optical fiber cable

that conforms to EIA standards. Other cables might not

function correctly.

When making connections between the digital signal

terminals, you should connect the components to the same-

named analog audio signal terminals of this unit, because a

digital signal cannot be recorded by a tape deck, MD

recorder or VCR connected to this unit.

■ TV monitor with a 21-pin connector

Make a connection as shown above with a commercially

available SCART-plug connector cable.

Notes

• Be sure to attach the covers when the OPTICAL terminals are not

being used in order to protect them from dust.

• If your LD player has a Dolby Digital RF signal output terminal,

be sure to use the RF demodulator (separately purchased).

• No sound will be heard when connecting your LD player’s Dolby

Digital RF signal output terminal directly to this unit’s COAXIAL

DVD/LD digital signal input terminal.

• The input signal from the DVD/LD input terminals is selected in

the following order of priority with the input mode set to AUTO:

COAXIAL terminal → OPTICAL terminal → Analog terminal.

Refer to page 22 for details.

• All digital signal input terminals are applicable to sampling

frequencies of 32 kHz, 44.1 kHz and 48 kHz.

CONNECTIONS

L R

L R V V

ANALOG

AUDIO OUT

AUDIO

OUT

AUDIO

VIDEO

OUT

VIDEO

ANALOG

AUDIO OUT

VIDEO

OUT

VIDEO

OUT

COAXIAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

DVD/LD player TV/digital TV, satellite tuner, cable TV

(Europe model)

VCR

Analog signal

Video signal

Digital signal

(optical)

Digital signal

(coaxial)

Signal flow

TV monitor

SCART-plug

No connection

0103V496RDS08-19_EN 1/6/0, 10:20 AM13

■ S VIDEO terminals

If your VCR, TV monitor or DVD/LD player has “S” (high-

resolution) video terminals, they can be connected to this

unit’s S VIDEO terminals. Connect the VCR’s “S” video

input and output terminals to this unit’s S VIDEO VCR

OUT and IN terminals, respectively. Connect the monitor’s

“S” video input terminal to this unit’s S VIDEO MONITOR

OUT terminal. Connect the DVD/LD player’s “S” video

output terminal to this unit’s S VIDEO DVD/LD terminal.

Otherwise, connect the composite video terminals of your

VCR, TV monitor or DVD/LD player to this unit’s

composite video terminals.

Notes

• Use a special S VIDEO cable (commercially available) for the S

VIDEO connection.

• If video signals are input from both the S VIDEO input and

composite input terminals, the signals will be directed to their

respective output terminals.

■ VIDEO AUX terminals (on the front panel)

These terminals are used to connect any video input source

such as a camcorder to this unit.

Connecting to an External Decoder

This unit has additional 6-channel audio signal input

terminals for connecting an external decoder to this unit.

Connect the 6-channel audio signal output terminals of the

decoder to the EXTERNAL DECODER INPUT terminals

of this unit.

Notes

• When a source connected to these terminals is selected, the digital

sound field processor cannot be used.

• The settings of “CENTER SP”, “REAR SP”, “MAIN SP” and

“BASS OUT” in the SET MENU have no effect on a source

connected to these terminals. The setting of “MAIN LVL” is

effective. (Refer to pages 37 and 38 for details.)

CONNECTIONS

L RV

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

Camcorder

S VIDEO OUT

S VIDEO

OUT

S VIDEO IN

DVD/LD player

TV Monitor

VCR

S Video signal

Signal flow

L R L R

MAIN

OUT

SURROUND

OUT

CENTER

OUT

SUBWOOFER

OUT

External decoder

(Europe model)

0103V496RDS08-19_EN 1/6/0, 10:20 AM14

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

Connecting Speakers

Be sure to connect the right channel (R), left channel (L),

“+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the

polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTIONS

• Use speakers with the specified impedance shown on

the rear panel of this unit.

• Do not let the bare speaker wires touch each other and

do not let them touch any metal part of this unit. This

could damage the unit and/or speakers.

■ Main speaker terminals

One or two speaker systems can be connected to these

terminals. If you use only one speaker system, connect it to

either of the SPEAKERS A or B terminals.

■ Rear speaker terminals

A rear speaker system can be connected to these terminals.

■ Center speaker terminal

A center speaker can be connected to this terminal.

CONNECTIONS

MAINS

100W MAX. TOTAL

SWITCHED

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

REAR

(SURROUND)

CENTER

MAIN

––++

–

Main speakers A

Right Left

Main speakers B

Right Left

(Europe model)

Center speaker Rear speakers

Right Left

Subwoofer connection

If you have a subwoofer with built-

in amplifier, including the

YAMAHA Active Servo Processing

Subwoofer System, connect the

input terminal of the subwoofer

system to the SUBWOOFER

OUTPUT terminal of this unit.

0103V496RDS08-19_EN 1/6/0, 10:20 AM15

■ Speaker cables

1 Remove approx. 10 mm (3/8”) of insulation

from each of the speaker cable.

2 Twist the exposed wires of the cable together

to prevent short circuits.

■ Connecting to the MAIN SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side of

each terminal.

3 Tighten the knob to secure the wire.

■ Connecting to the REAR and CENTER SPEAKERS terminals

1 Open the tab.

2 Insert one bare wire into the hole of each

terminal.

3 Return the tab to secure the wire.

CONNECTIONS

10 mm (3/8”)

Red: positive (+)

Black: negative (–)

Red: positive (+)

Black: negative (–)

0103V496RDS08-19_EN 1/6/0, 10:20 AM16

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

IMPEDANCE SELECTOR Switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise the unit may be

damaged.

If this unit fails to turn on when STANDBY/ON is pressed, the IMPEDANCE SELECTOR switch may not be fully slide

to either position. If so, slide the switch to either position fully when this unit is in the standby mode.

Select the right or left position according to the impedance of speakers in your system. Be sure to move this switch only

when this unit is in the standby mode.

Connecting the Power Supply Cords

After completing all connections, connect the AC power

cord to an AC power outlet. Disconnect the AC power cord

if you will not use this unit for a long period of time.

■ AC OUTLETS (SWITCHED)

Europe model .................................................... 2 OUTLETS

U.K. model.......................................................... 1 OUTLET

Use these outlets to connect the power cords from your

components to this unit. The power to the AC OUTLET(S)

is controlled by this unit’s STANDBY/ON (or POWER).

These outlets will supply power to any connected

component whenever this unit is turned on. The maximum

power (total power consumption of components) that can be

connected to the AC OUTLET(S) is 100 W.

If you use left position right position

Center

speaker

The impedance must be 6 Ω

or higher.

The impedance must be 8 Ω

or higher.

Rear

speakers

The impedance of each

speaker must be 6 Ω or

higher.

The impedance of each

speaker must be 8 Ω or

higher.

If you use two pairs of main

speakers, the impedance of

each speaker must be 8 Ω or

higher.

If you use two pairs of main

speakers, the impedance of

each speaker must be 16 Ω or

higher.

Main

speakers

If you use one pair of main

speakers, the impedance of

each speaker must be 4 Ω or

higher.

If you use one pair of main

speakers, the impedance of

each speaker must be 8 Ω or

higher.

CONNECTIONS

(Europe model)

MAINS

100W MAX. TOTAL

SWITCHED

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

SWITCHED

(Europe model)

To AC outlet

MAINS

100W MAX. TOTAL

SWITCHED

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

IMPEDANCE

SELECTOR

0103V496RDS08-19_EN 1/6/0, 10:20 AM17

Using the Test Tone

The adjustment of each speaker sound output level should

be performed at your listening position with the remote

control. After completing the adjustments, use VOLUME

(u/d) at your listening position to check if the adjustments

are satisfactory.

1 Press AMP(TUNER) on the

component selector.

2 Press TEST.

“TEST LEFT” appears on the display.

3 Turn up the volume.

You will hear a test tone (like pink noise) from each

speaker for about two seconds in following order: left

main speaker, center speaker, right main speaker, right

rear speaker and left rear speaker. The display changes

as shown below.

Notes

• If the test tone cannot be heard, turn down the volume, set the unit

in the standby mode and check the speaker connections.

• If the test tone cannot be heard from the center speaker, check the

setting of “CENTER SP” in the SET MENU.

This procedure lets you adjust the sound output level

balance between the main, center and rear speakers by using

the built-in test tone generator. When this adjustment is

performed, the sound output level heard at the listening

position will be the same from each speaker. This is

important for the best performance of the digital sound field

processor, the Dolby Pro Logic decoder, Dolby Digital

decoder and DTS decoder.

Before You Start Adjusting

1 Set VOLUME to the “m”

position.

2 Turn the power on.

3 Press SPEAKERS A or B

to select the main

speakers to be used.

If you use two main speaker

systems, press both A and B.

4 Set BASS, TREBLE and BALANCE to the “0”

position.

ADJUSTING THE SPEAKER BALANCE

–+–+

2,7

TEST

LEFT

TEST

RIGHT

TEST L SUR. TEST R SUR.

TEST CENTER

0103V496RDS08-19_EN 1/6/0, 10:20 AM18

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

4 Adjust BALANCE on the

front panel so that the

sound output level of the

right main speaker and the

left main speaker is the

same.

5 Press TIME/LEVEL

repeatedly to select the

speaker to be adjusted.

“CENTER”, “R SUR.” or

“L SUR.” appears on the

display.

6 Press + to raise and – to

lower the level. Adjust the

sound output levels of the

center speaker and the

rear speakers so that they

become almost the same

as that of the main

speakers.

While adjusting, the test tone is

heard from the selected speaker.

Note

• You cannot adjust the delay time while the test tone is being heard

even if “DELAY” appears on the display.

7 When the adjustment is complete, press TEST.

“TEST OFF” appears on the display and the test tone

stops.

Note

• If “CENTER SP” in the SET MENU is set to the NONE position,

the sound output level of the center speaker cannot be adjusted in

step 6. The center channel sound is automatically output from the

right and left main speakers.

• Once you have completed the adjustments, you can only adjust

the overall volume level of your audio system by using VOLUME

(or VOLUME (u/d)).

• If there is insufficient sound output from the center and rear

speakers, you may decrease the main speaker output level by

setting “MAIN LVL” in the SET MENU to “–10 dB”. (Refer to

page 38 for details.)

ADJUSTING THE SPEAKER BALANCE

Front panel

0103V496RDS08-19_EN 1/6/0, 10:20 AM19

When using the remote control, press AMP(TUNER) on

the component selector.

1 Set VOLUME to the “m”

position.

2 Turn the power on.

3 Press SPEAKERS A or B

to select the main

speakers to be used.

If you use two main speaker

systems, press both A and B.

PLAYING A SOURCE

–+–+

1,6

4 Select the desired input

source with INPUT

SELECTOR (or the input

selector buttons). (Turn on

the TV monitor for video

sources.)

The name of the selected input

source appears for a moment

and the arrow for the selected

input source indicator lights up

on the display.

a. To select a tape or an MD source

Press TAPE/MD MON / EXT.

DECODER (or TAPE/MD) so

that the “TAPE/MD

MONITOR” indicator lights up

on the display.

b. To select a source connected to the

EXTERNAL DECODER INPUT terminals

Press TAPE/MD MON / EXT. DECODER repeatedly

(or EXT. DEC.) until “EXT. DECODER” appears on

the display.

Notes

• An audio source can not be played if the “TAPE/MD MONITOR”

indicator lights up or if “EXT. DECODER” appears. Press TAPE/

MD MON / EXT. DECODER twice (or TAPE/MD once) to turn

off the “TAPE/MD MONITOR” indicator. Press TAPE/MD

MON / EXT. DECODER once (or EXT. DEC.) to turn off “EXT.

DECODER”.

• If you select and play a video source when the “TAPE/MD

MONITOR” indicator lights up or “EXT. DECODER” appears,

the play back result will be a video image from the video source

and the sound from the audio source selected by using TAPE/MD

MON / EXT. DECODER (or TAPE/MD or EXT. DEC.).

For the DVD/LD, TV/digital TV and satellite tuner sources, the

current input mode is also shown. Refer to page 22 for details about

the input mode.

Front panel

Remote control

Front panel

Input source

BASIC OPERATION

Front panel Remote control

0104V496RDS20-24_EN 1/12/0, 11:12 AM20

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

5 Play the source.

Refer to the instructions for the source component (and

page 28 for details about tuning).

Note

• When controlling an audio/video component (tape deck, MD

recorder, CD player, DVD/LD player, etc.) with the remote

control, press one of the component selector buttons, (TAPE/MD,

CD, DVD/LD, etc.), which corresponds to the component you

want to control. Refer to “PRESET REMOTE CONTROL” on

page 43.

6 Adjust the volume to the desired output level.

If desired, adjust BASS, TREBLE, BALANCE, etc.

These controls are only effective for the sound from the

main speakers.

• BASS controls the low-frequency response.

• TREBLE controls the high-frequency response.

• BALANCE adjusts the balance of the output volume

from the right and left main speakers.

7 Use the digital sound field processor.

Refer to page 24.

PLAYING A SOURCE

■ To mute the sound

Press MUTE on the remote

control.

To cancel mute, press MUTE.

Note

• During muting, “MUTE ON” appears on the display.

■ When you have finished using this

unit

Press STANDBY/ON (or POWER) to set this unit in the

standby mode.

■ BGV (background video) function

The BGV function allows you to combine a video image

from a video source with a sound from an audio source.

(For example, you can listen to classical music while you

are watching a video.) This function can only be controlled

with the remote control.

Play a video source, and then select an audio source with

the input selector buttons on the remote control. The BGV

function does not work if you select the audio source with

INPUT SELECTOR on the front panel.

Front panel Remote control

–+–+

Front panel

Front panel Remote control

0104V496RDS20-24_EN 1/6/0, 10:30 AM21

Input Mode (for the DVD/LD and TV/

digital TV and satellite tuner

sources)

This unit allows you to switch the input mode for sources

that send both digital and analog signals to this unit. The

AUTO, DTS and ANALOG input modes are provided.

When you turn on the power of this unit, the input mode for

the DVD/LD source is always set to AUTO and for TV/

digital TV or satellite tuner source is set according to “SAT

INPUT” in the SET MENU. (Refer to page 39 for details.)

■ AUTO

In this mode, the input signal is selected in the following

order of priority:

1. Digital signal encoded with Dolby Digital or DTS

2. Normal digital signal (PCM)

3. Analog signal (ANALOG)

Note

• If digital signals are input from both the OPTICAL and

COAXIAL terminals, the digital signal from the COAXIAL

terminal is selected.

■ DTS

In this mode, only a digital signal encoded with DTS is

selected, even if other signals are being input at the same

time.

■ ANALOG

In this mode, only an analog signal is selected, even if a

digital signal is being input at the same time. Select this

mode when you want to use an analog signal instead of a

digital signal.

PLAYING A SOURCE

■ Switching the input mode

Press INPUT MODE (or the input selector

button that you have pressed to select the

input source on the remote control) repeatedly

until the desired input mode is shown on the

display.

Notes

• Set the input mode to AUTO to play a DVD/LD source encoded

with Dolby Digital.

• Set the input mode to ANALOG to play a normal 2-channel

source with a Dolby Surround program.

• The sound output may be interrupted for some LD and DVD

players in the following situation: The input mode is set to

AUTO. A search is performed while playing the disc encoded

with Dolby Digital or DTS, and then disc playing is restored. The

sound output is interrupted for a moment because the digital

signal was selected again.

• The input mode cannot be changed for the CD, TUNER, TAPE/

MD, VCR, PHONO and VIDEO AUX sources because only

analog signals are used for these.

• The current input mode appears on the display when the DVD/

LD, TV/digital TV or satellite tuner source is selected or the input

mode is changed.

Front panel Remote control

0104V496RDS20-24_EN 1/12/0, 11:12 AM22

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

■ Notes on playing a source

encoded with DTS

• If “DATA ERROR” appears on the display while playing an LD

source encoded with DTS, stop playback and turn the player off

and then on again.

• If the digital output data of the player has been processed in any

way, you may not be able to perform DTS decoding even if you

make a digital connection between this unit and the player.

• If you play an LD source encoded with DTS and set the input

mode to ANALOG, there will be the noise of an unprocessed

DTS signal. When you want to play a DTS source, be sure to

connect the source to the digital input terminal and set the input

mode to AUTO or DTS.

• If you switch the input mode to ANALOG while playing a source

encoded with a DTS signal, this unit reproduces no sound.

• If you play an LD source encoded with DTS and set the input

mode to AUTO, there will be a short noise at first while the unit

recognizes the DTS signal and turns on the DTS decoder. This is

not a malfunction, and can be avoided by setting the input mode

to DTS beforehand. In addition, if you continue to play an LD

encoded with DTS with the input mode setting left to AUTO, this

unit automatically switches to the “DTS-decoding” mode to

prevent noise from being generated during subsequent operation.

(The “t” indicator lights up on the display.) No sound will be

heard if a normal PCM LD is played in this mode. (The “t”

indicator will flash.) To play a normal disk, set the input mode to

AUTO again.

PLAYING A SOURCE

■ Notes on playing an LD source

• Some audio/video component, such as LD player, output different

audio signals through their analog and digital terminals. Change

the input mode as necessary.

• If the input mode is set to AUTO for the LD source, this unit

automatically determines which type of signal the LD source

contains. If this unit detects a Dolby Digital or DTS signal, the

decoder automatically switches to the appropriate setting and

reproduces 5.1 channel sound.

• If the LD player is transmitting signals by a non-normal method,

this unit cannot detect the Dolby Digital or DTS signal. In this

case, the decoder automatically switches to PCM or analog.

• If the LD source does not contain a digital soundtrack, connect

the LD player to the analog terminals and set the input mode to

AUTO or ANALOG.

• While you are operating the LD player, if you switch from the

pause or chapter forwarding function to normal playback, you

may hear the PCM or analog sound an instant before the Dolby

Digital sound is played.

0104V496RDS20-24_EN 9/28/0, 4:41 PM23

3 Press PRG+ or PRG–

repeatedly to select the

desired program.

The name of the selected

program appears on the display.

If desired, adjust the delay time and the sound output level of each

speaker. (Refer to pages 40 and 41 for details.)

Notes

• You can select a DSP program for each of the input sources. Once

you select a program, it is linked with the input source selected at

that time. So, when you select the input source next time, the

same program is automatically selected.

• When a monaural source is being played with PRO LOGIC/

Normal or PRO LOGIC/ENHANCED, no sound will be heard

from the main speakers and the rear speakers. Sound can only be

heard from the center speaker. However, if “CENTER SP” in the

SET MENU is set to the NONE position, the center channel

sound is output from the main speakers.

• When a source connected to the EXTERNAL DECODER INPUT

terminals of this unit is selected, the digital sound field processor

cannot be used.

Canceling the Sound Effect (turning

off the effect speakers)

Press EFFECT to cancel

the sound effect and

monitor only the main

sound.

Press EFFECT again to turn the

sound effect back on.

Notes

• If the sound effect is canceled when Dolby Digital or DTS is

decoding, the sounds of all channels are mixed and output from

the main speakers.

• If you turn off the sound effect when Dolby Digital or DTS is

decoding, it may happen that the sound is output faintly or not

output normally, depending on the source. In that case, turn back

on the sound effect.

DIGITAL SOUND FIELD PROCESSOR (DSP) EFFECT

Selecting a DSP Program

You can enhance your listening experience by selecting a

DSP program. Refer to pages 25 to 27 for details about each

program.

■ On the front panel

1 Make sure that the effect speakers (center,

rear, and subwoofer) are turned on.

2 Press PROGRAM h or l

repeatedly to select the

desired program.

The name of the selected

program appears on the display.

■ On the remote control

1 Make sure that the effect speakers (center,

rear, and subwoofer) are turned on.

2 Press AMP(TUNER) on the

component selector.

–+–+

DSP program name

Front panel

Remote control

0104V496RDS20-24_EN 1/12/0, 11:12 AM24

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

[4] PRO LOGIC/ENHANCED

( ox)

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 4 channels

• DSP: 1 (surround)

[5] DOLBY DIGITAL/ENHANCED

( gx )

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: 2 (surround L, R)

[6] DTS DIGITAL SUR/ENHANCED

( tx)

• Input source: DTS

• Output channel: 5.1 channels

• DSP: 2 (surround L, R)

This program ideally simulates the multi-

surround speaker systems of the 35 mm-film

movie theater. Dolby Pro Logic decoding,

Dolby Digital decoding or DTS decoding and

digital sound field processing are precisely

performed without altering the original sound

orientation.

The surround effect produced by the sound

field folds around the viewer naturally from

the rear to the right and left and toward the

screen.

SOUND FIELD PROGRAM

This unit incorporates a sophisticated, multi-program digital sound field processor (DSP). This processor allows you to

electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theater-

like experience in your listening room. You can create outstanding audio sound by selecting a suitable DSP program (this

will, of course, depend on what you are listening to).

When you select a CINEMA DSP program, one of the built-in decoders (Dobly Pro Logic, Dolby Digital and DTS) is turned

on according to which type of signals the source being played contains.

The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that

most of these are precise digital re-creations of actual acoustic environments.

■ For movie or audio/video sources (Program No. 1 to No. 5: CINEMA DSP

programs)

No. PROGRAM SUBPROGRAM FEATURES

1 q/DTS

SURROUND

[1] PRO LOGIC/Normal ( o )

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 4 channels

• DSP: —

[2] DOLBY DIGITAL/Normal ( g )

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: —

[3] DTS DIGITAL SUR/Normal ( t )

• Input source: DTS

• Output channel: 5.1 channels

• DSP: —

The built-in Dolby Pro Logic decoder, Dolby

Digital decoder or DTS decoder precisely

reproduces the sound and effect of a source

encoded with Dolby Surround, Dolby Digital

or DTS.

The realization of a highly efficient decoding

process improves cross talk and channel

separation, and makes sound positioning

smoother and more precise.

In this program, the digital sound field

processor is not turned on.

0105V496RDS25-27_EN 1/6/0, 10:30 AM25

No. PROGRAM SUBPROGRAM FEATURES

2 MOVIE

THEATER 1

3 MOVIE

THEATER 2

[1] 70 mm SPECTACLE

( ox)

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 3 channels

• DSP: 2 (presence & surround)

[2] DGTL SPECTACLE

( g x )

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

[3] DTS SPECTACLE ( tx )

• Input source: DTS

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

This program creates the extremely wide sound

field of a movie theater. It precisely reproduces

the source sound in detail, giving both the video

and the sound field incredible reality. It is ideal

for any kind of video source encoded with

Dolby Surround, Dolby Digital or DTS

(especially large-scale movie productions).

[1] 70 mm ADVENTURE

( ox )

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 3 channels

• DSP: 2 (presence & surround)

[2] DGTL ADVENTURE

( gx)

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

[3] DTS ADVENTURE ( t x )

• Input source: DTS

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

Ideal for precisely reproducing the sound of the

newest multi-track films. The sound field is

made to be similar to that of the newest movie

theaters, so the reverberations of the sound field

itself are restrained as much as possible. The

data for the sound field of an opera house are

used for the front presence, so the three-

dimensional feeling of the sound field is

emphasized, and dialog is precisely oriented on

the screen. By using the data for the sound field

of a concert hall on the surround sound field,

powerful reverberations are generated. You can

enjoy watching action, adventure movies, etc.

with strong presence.

[4] 70 mm GENERAL ( ox )

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 3 channels

• DSP: 2 (presence & surround)

[5] DGTL GENERAL ( gx )

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

[6] DTS GENERAL ( t x )

• Input source: DTS

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

This program is for reproducing sounds on a

multi-track film, and is characterized by a soft

and extensive sound field. The front presence of

the sound field is relatively narrow. It spatially

spreads all around and toward the screen,

restraining echo effect of conversations without

losing clarity. For the surround sound field, the

harmony of music or chorus sounds beautifully

in a wide space at the rear of the sound field.

[4] 70 mm SCI-FI ( o x )

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 3 channels

• DSP: 2 (presence & surround)

[5] DGTL SCI-FI ( g x )

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

[6] DTS SCI-FI ( t x )

• Input source: DTS

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

Clearly reproduces dialog and sound effects in

the latest sound form of science fiction films,

thus creating a broad and expansive cinematic

space amid the silence. You can enjoy science

fiction films in a virtual-space sound field that

includes Dolby Surround, Dolby Digital and

DTS-encoded software employing the most

advanced techniques.

SOUND FIELD PROGRAM

0105V496RDS25-27_EN 1/6/0, 10:30 AM26

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

No. PROGRAM FEATURES

4 MONO MOVIE

• Input source: Monaural

• Output channel: 1 channel

• DSP: 1

This program is designed specifically to enhance monaural

sources. Compared to a strictly mono setting, the sound image

is wider and slightly forward of the speaker pair, lending an

immediacy to the overall sound. It is particularly effective for

old mono movie, news broadcasts and dialog.

5 TV SPORTS

• Input source: Audio/Video

• Output channel: 2 to 5.1 channels

• DSP: 2 to 3 (presence & surround)

This program is furnished with a tight sound field in which the

sound will not spread excessively at the front, but the rear

surround produces dynamic sound expansion. It is the most

suitable for sports programs.

■ For Hi-Fi audio sources

No. PROGRAM FEATURES

6 DISCO

• Input source: 2-ch PCM/Analog audio

• Output channel: 2 channels

• DSP: 1

This program simulates the acoustic environment of a disco in

the heart of a lively city. The sound is dense and highly

concentrated.

7 ROCK CONCERT

• Input source: 2-ch PCM/Analog audio

• Output channel: 2 channels

• DSP: 1

This program is ideally suited for rock music. You will

experience a dynamic and lively sound field.

8 CONCERT HALL

• Input source: 2-ch PCM/Analog audio

• Output channel: 2 channels

• DSP: 1

This program creates the expansive ambience of a large concert

hall. It is suited for orchestra and opera music.

CINEMA DSP: Dolby Surround + DSP/Dolby Digital + DSP/DTS + DSP

■ Dolby Pro Logic + 2 digital sound fields

Digital sound fields are created in both the presence and

rear surround zones of the Dolby Pro Logic-decoded sound

field. They create a wide acoustic environment and

emphasize the surround effect in the room, letting you feel

as much presence as if you were watching a movie in a

popular Dolby Stereo theater.

■ Dolby Digital or DTS + 3 digital sound fields

Digital sound fields are created in the presence zone and

independently on the left and right surround zones of the

Dolby Digital-decoded or DTS-decoded sound field. They

create a wide acoustic environment and strong surround

effect in the room without losing high channel separation.

With the wide dynamic range of Dolby Digital or DTS

sound, this sound field combination lets you feel as if you

were watching a movie in the newest Dolby Digital theater

or DTS-installed theater. This is the most ideal home theater

sound at the present time.

SOUND FIELD PROGRAM

0105V496RDS25-27_EN 1/6/0, 10:30 AM27

5 Press PRESET/TUNING h once to tune in to a

higher frequency and l once to tune in to a

lower frequency.

Press the button again if the tuning search does not stop

at the desired station.

Note

• If you tune in manually to an FM station, it will be automatically

received in monaural mode to increase the signal quality.

• Use the manual tuning method if the tuning search does not stop

at the desired station (because the signal from the station is weak).

• When tuned in to a station, the frequency of the received station is

shown on the display. If an RDS station that offers the PS data

service is being received, the station name is shown instead of the

frequency on the display.

Manual Tuning

1 Use INPUT SELECTOR to

select the tuner as the

input source.

2 Press FM/AM to select the reception band (FM

or AM).

“FM” or “AM” appears on the display.

3 Press TUNING MODE so that the “AUTO”

indicator goes off.

4 Press PRESET/TUNING (EDIT) to turn “ z ” off.

5 Press PRESET/TUNING h or l to tune in to

the desired station.

To continue the tuning search, hold down the button.

TUNING

–+–+

Automatic tuning is effective when station signals are

strong and there is no interference. However, if the signal

from the station you want to select is weak, you must tune

in to it manually (manual tuning).

Automatic Tuning

1 Use INPUT SELECTOR to

select the tuner as the

input source.

2 Press FM/AM to select the reception band (FM

or AM).

“FM” or “AM” appears on the display.

3 Press TUNING MODE so that the “AUTO”

indicator lights up on the display.

4 Press PRESET/TUNING (EDIT) to turn “ z ” off.

Lights up

Goes off

Turn “ z ” off

0106V496RDS28-31_EN 1/6/0, 10:30 AM28

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

Automatic Preset Tuning (for RDS

stations only)

You can make use of the automatic preset tuning function

for RDS stations only. This function enables the unit to

automatically tune in with strong signals and to sequentially

store up to 40 RDS stations (5 groups x 8 stations). (Refer to

pages 32 to 34 for details on RDS stations.)

1 Press FM/AM to select the FM band.

2 Press TUNING MODE so that the “AUTO”

indicator lights up on the display.

3 Hold down MEMORY for about three seconds.

The preset number, the “MEMORY” and “AUTO”

indicators flash. After about five seconds, automatic

preset tuning begins from the frequency currently

displayed toward the higher frequencies.

Received stations are sequentially stored as A1, A2 ...

A8. If more than 8 stations have been tuned, they are

stored as preset station numbers in other groups (B, C,

D and E) in that order.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost when this unit is set in the standby mode.

If, however, the power cord is disconnected from the AC

power outlet or the power is cut for more than one week,

the memory will be erased. If so, store the stations again

by using preset tuning methods.

–+–+

213

■Automatic preset tuning options

You can select the preset number from which the unit will

store RDS stations and/or begin tuning toward lower

frequencies. Before automatic preset tuning begins (after

pressing MEMORY in step 3),

1. Press A/B/C/D/E and PRESET/TUNING to select the

preset number with which the first station will be stored.

The automatic preset tuning will stop when stations have

all been stored up to E8.

2. Press PRESET/TUNING (EDIT) to turn “ z ” off and

then press PRESET/TUNING l to begin tuning toward

lower frequencies.

■ When automatic preset tuning is

completed

The display shows the frequency of the last preset station.

Check the contents and the number of preset stations by

following the procedure in the section “To Recall a Preset

Station” on page 30.

Notes

• A new setting can be stored in place of the former one.

• You can manually replace a preset station with another FM or AM

station by simply using the manual preset tuning method.

• Automatic preset tuning will be performed for all RDS network

stations until all have been stored up to E8. Even if the number of

received stations is not enough to be stored up to E8, automatic

preset tuning is automatically ended after searching for all

stations.

• Only RDS stations with sufficient signal strength are stored by

automatic preset tuning. If the station you want to store is weak in

signal strength, tune in to it manually in monaural mode and store

it by using the manual preset tuning method. (There may be a

case that this unit cannot receive a station which could be

received by using the automatic tuning method. This is because

this unit receives a large amount of PI (Program Identification)

data along with the station.)

TUNING

Lights up

Flashes

0106V496RDS28-31_EN 1/19/0, 10:27 AM29

TUNING

To Recall a Preset Station

You can recall any desired station simply by selecting the

preset station number with which it was stored.

You can also recall a preset station with the remote control.

Press AMP(TUNER) on the component selector and press

TUNER on the input selector.

1 Press A/B/C/D/E to select the required group

of preset stations.

Make sure that “ z ” appears on the display.

2 Press PRESET/TUNING h or l (or PRESET

+/–) to select a preset station number (1 to 8).

The preset group and number appear on the display

along with the reception band, frequency and signal

strength information.

–+–+

1 2

Flashes

Front panel

Remote control

Front panel

Remote control

–+–+

3 2,54

Manual Preset Tuning

You can also store up to 40 stations (5 groups x 8 stations)

manually.

1 Tune in to the desired station.

Refer to page 28 for the tuning procedure.

2 Press MEMORY.

The “MEMORY” indicator flashes for about five

seconds.

3 Press A/B/C/D/E repeatedly to select the

desired group (A to E) of preset stations

before the “MEMORY” indicator goes off.

Make sure that “ z ” appears on the display. The

selected group appears on the display.

4 Press PRESET/TUNING h or l to select a

preset station number (1 to 8) with which you

want to store the station before the “MEMORY”

indicator goes off.

Press h to select a higher

preset station number and l to

select a lower preset station

number.

5 Press MEMORY before the “MEMORY”

indicator goes off.

The displayed station has been stored as the preset

group and number you have selected, and the reception

band and frequency appear on the display.

6 Repeat steps 1 to 5 to store other stations.

Notes

• A new setting can be stored in place of the former one.

• The reception mode (stereo or monaural) is stored along with the

station frequency.

0106V496RDS28-31_EN 1/12/0, 11:14 AM30

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

–+–+

2,4

Exchanging Preset Stations

You can exchange the assignment of two preset stations

with each other.

■ Example: If you want to exchange

preset station “E1” with “A5”.

1 Recall preset station “E1”.

Refer to the procedure in the section “To Recall a

Preset Station” on page 30.

2 Hold down (PRESET/TUNING) EDIT for about

three second.

“E1” and the “MEMORY” indicator flash.

3 Recall preset station “A5” by using the buttons

on the front panel.

“A5” and the “MEMORY”

indicator flash.

4 Press (PRESET/TUNING) EDIT again.

The display shows the exchange of stations has been

completed.

TUNING

Flashes

0106V496RDS28-31_EN 1/19/0, 10:27 AM31

RECEIVING RDS STATIONS

Radio Data System (RDS) is a data transmission system by

FM stations in many countries. Stations using this system

transmit an inaudible stream of data in addition to the

normal radio signal.

RDS data contains various information such as PI (Program

Identification), PS (Program Service name), PTY (Program

Type), RT (Radio Text), CT (Clock Time), EON (Enhanced

Other Networks), etc. The RDS function is carried out

among the network stations.

Description of RDS Data

This unit can receive PI, PS, PTY, RT, CT, and EON data

when receiving RDS broadcasting stations.

■ PS (Program Service name) mode:

The name of the RDS station being received is displayed.

■ PTY (Program Type) mode:

The program type on the RDS station being received is

displayed. There are 15 program types to classify RDS

stations. You can make this unit search for a station which is

broadcasting a program of the desired type. Refer to page 33

for details.

■ RT (Radio Text) mode:

Information about the program (such as the title of the song,

name of the singer, etc.) on the RDS station being received

is displayed by a maximum of 64 alphanumeric characters,

including the umlaut symbol. If other characters are used for

RT data, they are displayed with under-bars.

■ CT (Clock Time) mode:

The current time is displayed and updated every minute. If

the data are accidentally cut off, “CT WAIT” may appear.

■ EON (Enhanced Other Networks):

Refer to page 34.

Changing the RDS Mode

The four modes are available in this unit for displaying RDS

data. When an RDS station is being received, PS, PTY, RT

and/or CT that correspond to the RDS data services offered

by the station light up on the display. Press RDS MODE/

FREQ repeatedly to change the display mode among the

RDS data offered by the transmitting station in the order

shown below. Illumination of the red indicator next to the

RDS mode indicator shows that the corresponding RDS

mode is now selected.

Notes

• When an RDS station is being received, do not press RDS

MODE/FREQ until one or more RDS mode indicators light up on

the display. If you press the button before the indicators light up

on the display, the mode cannot be changed. This is because the

unit has not yet received all of the RDS data on the station.

• RDS data not offered by the station cannot be selected.

• The RDS data service cannot be utilized by this unit if the

received signal is not strong enough. In particular, the RT mode

requires a large amount of data to be received, so it is possible

that the RT mode may not be displayed even if other RDS modes

(PS, PTY, etc.) are displayed.

• RDS data cannot sometimes be receive under poor reception

conditions. If so, press TUNING MODE so that the “AUTO”

indicator goes off from the display. Although the reception mode

is changed to monaural by this operation, when you change the

display to RDS mode, RDS data may be displayed.

• If the signal strength is weakened by external interference during

the reception of an RDS station, the RDS data service may be cut

off suddenly and “...WAIT” will appear on the display.

PS mode

PTY mode

RT mode

CT mode

Frequency

display mode

0107V496RDS32-35_EN 1/6/0, 11:07 AM32

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

PTY SEEK Function

If you select the desired program type, the unit

automatically searches all preset RDS stations that are

broadcasting a program of the required type.

1 Press PTY SEEK MODE to set the unit in the

PTY SEEK mode.

The program type of the station being received or

“NEWS” flashes on the display.

2 Press PRESET/TUNING h or l to select the

desired program type.

The selected program type appears on the display.

3 Press PTY SEEK START to begin searching all

preset RDS stations.

The selected program type flashes and the “PTY

HOLD” indicator lights up on the display while

searching for stations.

• If a station that is broadcasting a program of the

required type is found, the unit stops at that station.

• If the called station is not the desired one, press PTY

SEEK START again. The unit begins searching for

another station that is broadcasting a program of the

same type.

RECEIVING RDS STATIONS

■ To cancel this function

Press PTY SEEK MODE twice.

■ Program types in the PTY mode

There are 15 program types to classify RDS stations.

NEWS News

AFFAIRS Current affairs

INFO General information

SPORT Sports

EDUCATE Education

DRAMA Drama

CULTURE Culture

SCIENCE Science

VARIED Light entertainment

POP M Pops

ROCK M Rock

M.O.R. M Middle-of-the-road music (easy-listening)

LIGHT M Light classics

CLASSICS Serious classics

OTHER M Other music

–+–+

312

Flashes

The selected

program type

flashes.

Light up

0107V496RDS32-35_EN 9/28/0, 4:42 PM33

EON Function

This function uses the EON data service on the RDS station

network. If you simply select the desired program type

(NEWS, INFO, AFFAIRS or SPORT), the unit

automatically searches for all preset RDS stations that are

scheduled to broadcast a program of the required type and

switches from the station being currently received to the

new station when the broadcasts starts.

Note

• This function can only be used when an RDS station that offers

the EON data service is being received. When such a station is

being received, the “EON” indicator lights up on the display.

1 Make sure that the “EON” indicator lights up

on the display.

If the “EON” indicator does not light up, tune in to

another RDS station so that the “EON” indicator lights

up.

–+–+

2 Press EON repeatedly to select the desired

program type (NEWS, INFO, AFFAIRS or

SPORT).

The selected program type name indicator lights up on

the display.

• If a preset RDS station of the selected program type

starts broadcasting, the unit will automatically switch

from the program being currently received to that

program. The program type name indicator flashes.

• When broadcasting of the required program ends, the

previously received station (or another program on

the same station) is recalled.

■ To cancel this function

Press EON repeatedly until no program type name lights up

on the display.

RECEIVING RDS STATIONS

Lights up

Flashes

0107V496RDS32-35_EN 1/12/0, 11:16 AM34

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

RECORDING A SOURCE ON TAPE, MD OR VIDEO CASSETTE

–+–+

1,42

Recording adjustments and other operations are performed

from the tape deck, MD recorder or VCR. Refer to the

instructions for these components.

1 Set VOLUME to the “m”

position.

2 Select the source you want to record.

3 Begin recording by the tape deck, MD recorder

or VCR connected to this unit.

4 Play the source and then turn up the volume to

confirm the input source.

If a tape deck or MD recorder is being used for recording, you can

monitor the sounds being recorded by pressing TAPE/MD MON /

EXT. DECODER (or TAPE/MD).

Notes

• The DSP program and the setting of VOLUME, BASS, TREBLE

and BALANCE have no effect on the material being recorded.

• Composite video and S video signals pass independently through

this unit’s video circuits. Therefore, when recording or dubbing

video signals, if your video source component is connected to

provide only an S video (or only a composite video) signal, you

can record only an S video (or only a composite video) signal by

your VCR.

• A source connected to this unit only through the digital terminals

cannot be recorded by the tape deck, MD recorder or VCR

connected to this unit.

• A source connected to the EXTERNAL DECODER INPUT

terminals of this unit cannot be recorded.

• Check the copyright laws in your country to record from records,

CDs, radio, etc. Recording of copyrighted material may infringe

If you play back a video source that uses scrambled or

encoded signals to prevent it from being dubbed, the

picture itself may be disturbed due to those signals.

Remote controlFront panel

Front panel

Remote control

0107V496RDS32-35_EN 1/6/0, 11:07 AM35

SET MENU

This unit provides you with the following items in the SET

MENU to maximize the performance of your system and

expand your enjoyment for audio listening and video

watching.

1. CENTER SP

2. REAR SP

3. MAIN SP

4. BASS OUT

5. MAIN LVL

6. D.D. LFE

7. D-RANGE

8. DTS LFE

9. CNTR DELAY

10.MEM. GUARD

11.SAT INPUT

Adjusting Items in the SET MENU

Adjustments should be performed with the remote control

while watching the information on the display.

1 Press AMP(TUNER) on the

component selector.

2 Press SET MENU

repeatedly to select the

item you want to adjust.

The selected item appears on

the display.

3 Press + or – repeatedly to

adjust the setting.

4 Repeat steps 2 and 3 to adjust the setting of

any other item in the same way.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost when this unit is set in the standby mode.

If, however, the power cord is disconnected from the AC

power outlet or the power is cut for more than one week,

the settings of the SET MENU will automatically return

to the preset positions and values. If so, adjust the

settings of the SET MENU again.

ADVANCED OPERATION

0108V496RDS36-42_EN 1/6/0, 11:07 AM36

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

Description of Each Item

1. CENTER SP

Choices: LRG (Large)/SML (Small)/NONE

Preset position: LRG (Large)

LRG (Large)

Select this position if your center speaker is approximately

the same size as the main speakers. In this position, full-

range signals on the center channel are directed to the center

speaker.

SML (Small)

Select this position if you use a center speaker that is

smaller than the main speakers. In this position, low bass

signals (below 90 Hz) on the center channel are distributed

to the SUBWOOFER OUTPUT terminal (or to the right and

left main speakers if “BASS OUT” is set to the MAIN

position).

NONE

Select this position if you do not have a center speaker

(4-speaker system). In this position, full-range signals on

the center channel are directed to the right and left main

speakers.

2. REAR SP

Choices: LARGE/SMALL

Preset position: LARGE

LARGE

Select this position if your rear speakers have high ability

for bass reproduction, or if a subwoofer is connected in

parallel to the rear speaker. In this position, full-range

signals on the rear channels are directed to the rear speakers.

SMALL

Select this position if your rear speakers do not have high

ability for bass reproduction. In this position, low bass

signals (below 90 Hz) on the rear channels are distributed to

the SUBWOOFER OUTPUT terminal (or to the right and

left main speakers if “BASS OUT” is set to the MAIN

position).

3. MAIN SP

Choices: LARGE/SMALL

Preset position: LARGE

LARGE

Select this position if your main speakers have high ability

for bass reproduction. In this position, full-range signals on

the main channels are directed to the right and left main

speakers.

SMALL

Select this position if your main speakers do not have high

ability for bass reproduction. However, if your system does

not include a subwoofer, do not select this position. In this

position, low bass signals (below 90 Hz) on the main

channels are distributed to the SUBWOOFER OUTPUT

terminal if “BASS OUT” is set to the SW or BOTH

position.

4. BASS OUT

Choices: SW/MAIN/BOTH

Preset position: BOTH

Select this position if your system includes a subwoofer. In

this position, signals on the LFE channel and other low bass

signals that are distributed from other channels are directed

to the SUBWOOFER OUTPUT terminal when playing a

source encoded with Dobly Digital or DTS.

Note

• When playing a 2-channel source (tape, MD, CD, video

cassette etc.), select the BOTH position to direct low bass signals

(below 90 Hz) to the SUBWOOFER OUTPUT terminals.

MAIN

Select this position if your system does not include a

subwoofer. In this position, besides full-range signals on the

main channels, signals on the LFE channel and other low

bass signals (below 90 Hz) that are distributed from other

channels are directed to the right and left main speakers.

BOTH

Select this position if your system includes a subwoofer. In

this position, signals on the LFE channel are directed to the

SUBWOOFER OUTPUT terminal. Low bass signals on the

main channels are directed to both the main speakers and

the SUBWOOFER OUTPUT terminal.

SET MENU

0108V496RDS36-42_EN 1/6/0, 11:07 AM37

7. D-RANGE (Adjusting the dynamic

range)

Choices: MAX/STD (Standard)/MIN

Preset position: MAX

Note

• This adjustment is only effective when Dolby Digital is being

decoded.

“Dynamic range” is the difference between the maximum

level and the minimum level of sounds. Sounds on a movie

originally designed for movie theaters feature a very wide

dynamic range. Dolby Digital technology can modify the

original sound track into a home audio format with this

wide dynamic range unchanged. Powerful sounds of

extremely wide dynamic range are not always suitable for

home use. Depending on the condition of your listening

environment, it may not be possible to increase the sound

output to a level as high as that in a movie theater. However,

at the normal level suitable for listening in your room, the

low-level parts of source sound often cannot be heard well

because they will be lost among noise in your environment.

Dolby Digital technology has also made it possible to

reduce an original sound track’s dynamic range for a home

audio format by “compressing” the sound data.

MAX

In this position, a source encoded with Dolby Digital is

reproduced in the original sound track’s wide dynamic

range to provide you with powerful sounds just like those in

a movie theater. Selecting this position will be even better if

you can listen to a source at a high output level in a room

specially soundproofed for audio/video enjoyment.

STD (Standard)

In this position, a source encoded with Dolby Digital is

reproduced in the “compressed” dynamic range of the

source that is suitable for low-level listening.

MIN

In this position, the dynamic range is more reduced than in

the STD position. Selecting this position will be effective

when you must listen to a source at a low level.

Note

• It may happen that sound is output faintly or not output normally

depending on the source. In that case, select the MAX or STD

position.

5. MAIN LVL

Choices: NORM (Normal)/–10 dB

Preset position: NORM (Normal)

NORM (Normal)

Normally select this position.

–10 dB

Select this position if the sound output from the main

speakers is too loud and cannot be balanced with the sound

output from the center and rear speakers. In this position,

the sound output from the main speakers is attenuated.

Notes

• The setting of “CENTER SP”, “REAR SP”, “MAIN SP” and

“BASS OUT” have no effect on a source connected to the

EXTERNAL DECODER INPUT terminals on the rear of this

unit.

• Once you have adjusted appropriately for “CENTER SP”, “REAR

SP”, “MAIN SP”, “BASS OUT” and “MAIN LVL”, you do not

have to change any settings unless your speaker system is

modified.

6. D.D. LFE (Adjusting the output

level of the LFE channel for Dolby

Digital)

Control range: –20 dB to 0 dB (in 1 dB steps)

Preset value: 0 dB

Note

• This adjustment is only effective when Dolby Digital is being

decoded and the selected source encoded with Dolby Digital

contains LFE signals.

This adjusts the output level of the LFE channel. If the LFE

signals are mixed with signals of other channels and they

are directed to the same speakers, the ratio of the LFE signal

level to the level of the other signals can be adjusted.

SET MENU

0108V496RDS36-42_EN 1/6/0, 11:07 AM38

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

8. DTS LFE (Adjusting the output

level of the LFE channel for DTS)

Control range: –10 dB to +10 dB (in 1 dB steps)

Preset value: 0 dB

Note

• This adjustment is effective only when DTS is being decoded and

the selected source encoded with DTS contains LFE signals.

This adjusts the output level of the LFE channel. If the LFE

signals are mixed with signals of other channels and they

are directed to the same speakers, the ratio of the LFE signal

level to the level of the other signals can be adjusted.

9. CNTR DELAY (Adjusting the delay

of the center sound)

Control range: 0 ms to 5 ms (in 1 ms steps)

Preset value: 0 ms

Note

• This adjustment is only effective when Dolby Digital or DTS is

being decoded and the selected source encoded with Dolby

Digital or DTS contains center channel signals.

This adjusts the delay between the main sound (on the main

channels) and dialog, etc. (on the center channel). The larger

the value, the later the dialog, etc. is generated.

This makes sounds from the left main, center and right main

speakers reach your listening position at the same time. This

is achieved by delaying the sound from the center speaker if

the distance from the center speaker to your listening

position is shorter than the distance from the right and left

main speaker to your listening position.

10.MEM. GUARD (Locking the

settings)

Choices: ON/OFF

Preset position: OFF

If you wish to prevent accidental alterations to the settings

of the SET MENU and other adjustments on this unit, select

the ON position. The following settings on this unit can be

locked:

• Settings of other items in the SET MENU

• Settings in the TIME/LEVEL mode

• Settings when using TEST

11.SAT INPUT (Selecting the initial

input mode for a source connected

to the SAT/D-TV input terminals)

Choices: AUTO/LAST

Preset position: AUTO

The input mode for a source connected to the SAT/D-TV

input terminals of this unit can be automatically set when

the power of this unit is turned on. Refer to page 22 for

details about the input mode.

AUTO

In this position, the input mode is always set to AUTO.

LAST

In this position, the input mode is automatically set to that

selected the last time when the power of this unit was turned

on.

SET MENU

0108V496RDS36-42_EN 1/6/0, 11:07 AM39

1. PRO LOGIC/Normal 15 to 30 20

DOLBY DIGITAL/Normal 0 to 15 5

DTS DIGITAL SUR/Normal 0 to 15 5

PRO LOGIC/ENHANCED 15 to 30 20

DOLBY DIGITAL/ENHANCED 0 to 15 5

DTS DIGITAL SUR/ENHANCED 0 to 15 5

2. 70 mm SPECTACLE 15 to 30 23

DGTL SPECTACLE 1 to 99 15

DTS SPECTACLE 1 to 99 15

70 mm SCI-FI 15 to 30 20

DGTL SCI-FI 1 to 99 16

DTS SCI-FI 1 to 99 16

3. 70 mm ADVENTURE 15 to 30 20

DGTL ADVENTURE 1 to 99 15

DTS ADVENTURE 1 to 99 15

70 mm GENERAL 15 to 30 20

DGTL GENERAL 1 to 99 15

DTS GENERAL 1 to 99 15

4. MONO MOVIE 1 to 99 49

5. TV SPORTS 1 to 99 9

6. DISCO 1 to 99 40

7. ROCK CONCERT 1 to 99 16

8. CONCERT HALL 1 to 99 44

DELAY TIME AND SPEAKER OUTPUT LEVELS

When using the digital sound field processor with the Dolby

Pro Logic decoder, Dolby Digital decoder or DTS decoder,

you can adjust the delay time between the main sound and

sound effect, and each speaker’s output level as you wish.

Delay Time

You can adjust the time difference between the beginning of

the sound from the main speakers and the beginning of the

sound effect from the rear speakers. The larger the value,

the later the sound effect is generated. The delay time can be

individually adjusted to all DSP programs.

Notes

• Adding too much delay will cause an unnatural effect with some

sources.

• The sound is momentarily interrupted while adjusting the delay

time.

Sound Output Level of the Center,

Right Rear and Left Rear Speakers,

and Subwoofer

If desired, you can adjust the sound output level of each

speaker even if it has already been adjusted in

“ADJUSTING THE SPEAKER BALANCE” on pages 18

and 19.

Notes

• The sound output level of the center speaker cannot be adjusted

when the input signal is analog, PCM audio, or encoded with

Dolby Digital in 2-channel.

• If “CENTER SP” in the SET MENU is set to the NONE position,

the sound output level of the center speaker cannot be adjusted.

This is because the center channel sound is automatically output

from the right and left main speakers.

• Once the sound output level has been adjusted, the level will be

the same for all DSP programs.

Speaker Control range (dB) Preset value

Center –20 to +10 0

Right rear –20 to +10 0

Left rear –20 to +10 0

Subwoofer –20 to 0 0

Program

Control

range (ms)

Preset

value

0108V496RDS36-42_EN 1/19/0, 10:24 AM40

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

Adjusting Method

Adjustments should be performed with the remote control

while watching the information on the display.

1 Press AMP(TUNER) on the

component selector.

2 Press TIME/LEVEL repeatedly to select the

item you want to adjust.

Each time you press TIME/LEVEL, the selected item

changes and appears on the display as below.

Note

• Depending on the setting of the SET MENU, you may not be able

to select all these items.

DELAY TIME AND SPEAKER OUTPUT LEVELS

DELAY

CENTER

R SUR.

L SUR.

SWFR

3 Press + or – to adjust the

delay time or speaker

output levels.

4 Repeat steps 2 and 3 to adjust the settings of

any other item.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost when this unit is set in the standby mode.

If, however, the power cord is disconnected from the AC

power outlet or the power is cut for more than one week,

the latest values for the delay time and the center/rear/

subwoofer output levels that were set will automatically

return to the preset values. If so, adjust the delay time

and output levels again.

0108V496RDS36-42_EN 1/6/0, 11:08 AM41

SLEEP TIMER

Canceling the Selected SLEEP

Timer

Press SLEEP repeatedly until “SLEEP OFF”

appears on the display.

It will soon disappear and the “SLEEP” indicator will

go off.

Note

• The SLEEP timer can also be canceled by setting the unit in the

standby mode by using POWER on the remote control (or

STANDBY/ON), or by disconnecting the AC power cord from

the AC power outlet.

The SLEEP timer can be used to automatically set this unit

in the standby mode. This timer is useful when you are

going to sleep while enjoying a broadcast or other desired

input source. The SLEEP timer can only be set with the

remote control.

Notes

• First press AMP(TUNER), TAPE/MD, CD or DVD/LD on the

component selector to set the SLEEP timer for this unit.

• The SLEEP timer is effective for the components connected to the

AC OUTLET(S) on the rear panel of this unit.

Setting the SLEEP Timer

1 Play a source you want to enjoy when you are

going to sleep.

2 Press SLEEP repeatedly to

select the desired SLEEP

time.

Each time you press SLEEP, the

SLEEP time will change as

below:

3 The “SLEEP” indicator soon lights up on the

display after the SLEEP timer has been set.

The display returns to the previous indication.

Lights up

Flashes

120 90 60 30

The SLEEP timer is off

(SLEEP OFF).

(This is the state before

SLEEP is pressed.)

0108V496RDS36-42_EN 1/12/0, 11:16 AM42

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

■ Example: To control YAMAHA CD

player

1 Make sure that VOLUME is set to the “m”

position.

2 Press AMP(TUNER) on the

component selector.

3 Turn on the power.

4 Press CD on the input selector.

PRESET REMOTE CONTROL

The provided remote control is factory set to control not only this unit but also most YAMAHA audio components connected

to it.

There are eight component selector buttons. Press one of these buttons which corresponds to the component you want to

control with the remote control. For example, if you press CD on the component selector, the remote control is set to the CD

operation mode, allowing the CD player to be controlled by the buttons on the remote control.

AMP(TUNER)

You can perform the basic operations of this

unit. Refer to page 7.

The code for a YAMAHA CD player is

factory set.

DVD/LD & DVD MENU

An LD player can be controlled in

the DVD/LD mode. A DVD player can be

controlled in the DVD/LD and DVD

MENU modes. The code for a YAMAHA

DVD player is factory set. If the remote

control does not operate your YAMAHA

DVD player, you need to set the code

number “0048”.

TAPE/MD

The code for a YAMAHA tape deck is

factory set. (The code for the YAMAHA

MD recorder can also be set.)

VCR

A VCR can be controlled.

A TV can be controlled.

CBL/SAT

A cable TV or satellite tuner can be

controlled.

Note

• The button functions on the remote control differ depending on the operation mode. Refer to the following pages for details.

Controlling the Components Connected to This Unit

5 Press CD on the

component selector.

6 Press p.

Refer to page 45 for the CD

player operation buttons.

7 Adjust the volume.

If you set the remote control with the manufacturers’

codes listed from page i at the end of this

manual, you can control other brands of components.

Refer to “Setup codes” on page 48 for details.

0109V496RDS43-49_EN 1/6/0, 11:08 AM43

Description of Each Mode

■ TAPE/MD MODE

Note

• TV VOLUME functions if you have set the code for your TV.

The dark-shaded buttons do not function. Refer to the instructions for details of each component.

PRESET REMOTE CONTROL

DISPLAY (MD)

SLEEP

EFFECT

MUTE

TV VOLUME

VOLUME

POWER

(TAPE) This button turns this unit on if you have set

the code for a YAMAHA tape deck. This button

turns on the tape deck that has a remote control with

a power button if you have set the code for another

manufacturer.

(MD) This button turns this unit on if you have set

the code for the YAMAHA MD recorder.

r REC/PAUSE

This button gives a pause in recording on a tape deck

or MD recorder.

p PLAY

This button plays a tape or an MD.

b DIR A (TAPE)

This button selects the playing direction of deck A.

SKIP– (MD)

This button skips to the previous track.

w REWIND (TAPE)

This button rewinds a tape.

SEARCH (MD)

This button initiates a backward search on the track

that is playing to find the point from which you want

to listen.

Press TAPE/MD.

Input selector buttons

DECK A/B (TAPE)

This button selects deck A or B on a double-cassette

tape deck.

e PAUSE (MD)

This button gives a pause in operation.

a DIR B (TAPE)

This button selects the playing direction of deck B.

SKIP+ (MD)

This button skips to the next track.

s STOP

This button stops operation on a tape deck or MD

recorder.

f FAST FORWARD (TAPE)

This button winds a tape fast forward.

SEARCH (MD)

This button initiates a fast-forward search on the track

that is playing to find the point from which you want to

listen.

0109V496RDS43-49_EN 1/6/0, 11:08 AM44

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

■ CD MODE

Note

• TV VOLUME and TV INPUT function if you have set the code for your TV.

e PAUSE

This button gives a pause in operation. The button

functions as PAUSE/STOP* for operating a

YAMAHA CD player under factory setting.

a SKIP+

This button skips to the beginning of the next

track.

s STOP

This button stops operation. The button functions

as PAUSE/STOP* for operating YAMAHA CD

players.

f SEARCH

This button initiates a fast-forward search on the

track that is playing to find the point from which

you want to listen.

The dark-shaded buttons do not function. Refer to the instructions for details of each component.

PRESET REMOTE CONTROL

PAUSE/STOP function

Press the button once to give a pause in operation and press once more to stop operation.

DISPLAY

SLEEP

EFFECT

MUTE

TV VOLUME

VOLUME

TV INPUT

Press CD.

POWER

This button turns this unit on if you have set the code

for a YAMAHA CD player. This button turns on the CD

player that has a remote control with a power button if

you have set the code for another manufacturer.

p PLAY

This button plays a CD.

b SKIP–

This button skips to the beginning of the previous

track.

w SEARCH

This button initiates a backward search on the track

that is playing to find the point from which you want

to listen.

Input selector buttons

DISC SKIP +/– (for a CD player with CD

changer)

These buttons skip to the next or previous CD.

0109V496RDS43-49_EN 1/6/0, 11:08 AM45

■ DVD/LD MODE

Note

• TV VOLUME and TV INPUT function if you have set the code for your TV.

■ DVD MENU MODE

Note

• TV VOLUME and TV INPUT function if you have set the code for your TV.

The dark-shaded buttons do not function. Refer to the instructions for details of each component.

PRESET REMOTE CONTROL

CLEAR

TV INPUT

TV VOLUME

VOLUME

RETURN

MENU UP

MUTE

MENU LEFT

MENU DOWN

TITLE

DISC SKIP +/–

INDEX

MENU SELECT

+10

MENU RIGHT

Press DVD MENU.

POWER

This button turns the unit on if you have

set the code for a YAMAHA DVD player.

This button turns on the DVD player that

has a remote control with a power button

if you have set the code for another

manufacturer.

Numeric buttons

EFFECT

TV INPUT

TV VOLUME

VOLUME

SLEEP

MUTE

SKIP –

STOP

DISC SKIP +/–

DISPLAY

PAUSE

PLAY

SKIP +

Press DVD/LD.

POWER

(DVD) This button turns this unit on if

you have set the code for a YAMAHA

DVD player. This button turns on the

DVD player that has a remote control

with a power button if you have set the

code for another manufacturer.

(LD) This button turns this unit on if you

have set the code for a YAMAHA LD

player. This button turns on the LD player

that has a remote control with a

power button if you have set the

code for another manufacturer.

Input selector buttons

0109V496RDS43-49_EN 1/6/0, 11:08 AM46

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

■ VCR MODE

Note

• TV VOLUME, TV INPUT and TV SLEEP function if you have

set the code for your TV.

■ CBL/SAT MODE

Note

• TV VOLUME, TV INPUT and TV SLEEP function if you have

set the code for your TV.

■ TV MODE

Note

• You can control your VCR if you have set the

code for it.

The dark-shaded buttons do not function. Refer to the instructions for details of each component.

PRESET REMOTE CONTROL

VCR REC

Press this button twice to

start recording.

Press VCR.

EFFECT

TV INPUT

TV VOLUME

VOLUME

TV SLEEP

MUTE

VCR STOP

VCR REWIND

VCR CHANNEL +/–

DISPLAY

VCR PAUSE

VCR PLAY

VCR

FAST FORWARD

CHANNEL

ENTER

CHANNEL

VCR POWER

Press CBL/SAT.

+100

TV INPUT

TV VOLUME

VOLUME

TV SLEEP

MUTE

MENU LEFT

MENU UP

MENU DOWN

RECALL

CBL/SAT

CHANNEL +/–

DISPLAY

MENU SELECT

CHANNEL

ENTER

MENU RIGHT

CBL/SAT POWER

CHANNEL

Press TV.

VCR REC

Press this button twice.

EFFECT

TV INPUT

TV VOLUME

VOLUME

TV SLEEP

TV MUTE

VCR STOP

VCR REWIND

TV CHANNEL +/–

DISPLAY

VCR PAUSE

VCR PLAY

VCR

FAST FORWARD

CHANNEL

ENTER

CHANNEL

TV POWER

0109V496RDS43-49_EN 1/6/0, 11:08 AM47

Advanced Information

■ Setup codes

You can set the code for the manufacturer of your

component after pressing the component selector buttons

other than AMP(TUNER).

1 Turn on your component to be used.

2 Press one of the

component selector

buttons which

corresponds to the

component to be

controlled.

3 Press both VOLUME

buttons (u/d) at the same

time for about four

seconds.

The indicator flashes twice.

4 Use the numeric buttons to

enter the four-digit

manufacturer’s code for

the component to be used.

Make sure that the

indicator flashes twice.

If the indicator does not flash,

repeat step 3 and re-enter the

code.

5 Press POWER (or any other button) on the

remote control to check if you have set the

code correctly.

If your component cannot be

controlled with the remote

control, try setting another code

for the same manufacturer.

Notes

• You can set only one code for one mode.

• In the DVD/LD and DVD MENU modes:

– Be sure to press DVD/LD on the component selector before

entering the code for the DVD/LD player. The code set in the

DVD/LD mode is also simultaneously set in the DVD MENU

mode. You cannot set the code for a DVD player after pressing

DVD MENU on the component selector.

– DVD MENU operations cannot be performed for some DVD

players.

• A second (and third) VCR can be controlled. Refer to “To use a

second (and third) VCR” for details.

• If your component does not respond to any of the codes listed for

the manufacturer, use the original remote control supplied with

your component.

PRESET REMOTE CONTROL

■ To use a second (and third) VCR

You can control a second (and third) VCR in the CBL/SAT

and DVD MENU modes if a cable TV or satellite tuner, or

DVD player is not being used.

Note

• If you want to control a second (and third) VCR in the DVD

MENU mode, you must set the code for an LD player in the

DVD/LD mode.

1 Turn on the VCR to be used.

2 Press CBL/SAT or DVD

MENU on the component

selector.

3 Press both VOLUME

buttons (u/d) at the same

time for about four

seconds.

The indicator flashes twice.

4 Use the numeric buttons to

enter the four-digit code

for the second (and third)

VCR. Make sure that the

indicator flashes twice.

If the indicator does not flash,

repeat step 3 and re-enter the

code.

5 Press POWER (or any other button) on the

remote control to check if you have set the

code correctly.

If the VCR cannot be controlled

with the remote control, try

setting another code for the

same manufacturer.

0109V496RDS43-49_EN 1/6/0, 11:08 AM48

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

■ Returning to the factory-set codes

To return all components to the factory-set codes, follow

these steps.

1 Press one of the

component selector

buttons other than

AMP(TUNER).

2 Press both VOLUME

buttons (u/d) at the same

time for about four

seconds.

The indicator flashes twice.

3 Enter the code number

“9990”.

Make sure that the indicator

flashes twice.

PRESET REMOTE CONTROL

To return each component to the factory-set codes, follow

these steps.

1 Press one of the

component selector

buttons which

corresponds to the

component to be returned

to the factory-set code.

2 Press both VOLUME

buttons (u/d) at the same

time for about four

seconds.

The indicator flashes twice.

3 Enter the code number

“0000”.

Make sure that the indicator

flashes twice.

The following codes are factory set.

Component

selector button

Component

Code

TV TV 0101

CBL/SAT Satellite tuner 0006

VCR VCR 0002

DVD/LD DVD player 0008 (YAMAHA DVD player)

CD CD player 0005 (YAMAHA CD player)

TAPE/MD Tape deck 0004 (YAMAHA Tape deck)

We recommend that you write all the code numbers you

have set on the “Quick Reference Card”.

0109V496RDS43-49_EN 1/6/0, 11:08 AM49

TROUBLESHOOTING

If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple

measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power

cord and contact your authorized YAMAHA dealer or service center.

■ General

SYMPTOM CAUSE REMEDY

The unit does not work

normally.

No sound and/or no

picture.

The power cord is not connected or the plug is

not completely inserted.

Firmly connect the power cord.

The IMPEDANCE SELECTOR switch on the

rear panel is not fully set to the right or left

position.

Set the switch fully to the right or left position

when the unit is in the standby mode.

The internal microcomputer has been frozen by

an external electric shock (lightning, excessive

static electricity, etc.) or by a power supply with

low voltage.

Set the unit in the standby mode and disconnect

the AC power cord from the AC power outlet.

After about 30 seconds have passed, connect

the power and operate the unit again.

The speaker connections are not secure.

Incorrect input or output cable connections. Connect the cables properly. If the problem

persists, the cables may be defective.

An appropriate input source has not been

selected.

Select an appropriate input source with INPUT

SELECTOR or TAPE/MD MON / EXT.

DECODER (or the input selector buttons).

Secure the connections.

SPEAKERS have not been set properly. Set SPEAKERS corresponding to the speakers

in use to the ON position.

No picture. There is no S VIDEO connection between this

unit and the TV monitor, although S video

signals are being input to this unit.

Connect the monitor’s “S” video input terminal

to this unit’s S VIDEO MONITOR OUT

terminal.

Only the speaker on one

side can be heard.

Incorrect cable connections. Connect the cables properly. If the problem

persists, the cables may be defective.

Incorrect setting of BALANCE. Adjust it to the appropriate position.

No sound from the effect

speakers.

The sound effect is off. Press EFFECT to turn it on.

A Dolby Surround, Dolby Digital or DTS

decoding DSP program is being used with

material not encoded with Dolby Surround,

Dolby Digital or DTS.

Select another DSP program.

No sound from the

center speaker.

The sound output level of the center speaker is

set to minimum.

Raise the level of the center speaker.

“CENTER SP” in the SET MENU is set to the

NONE position.

Select the LRG or SML position.

The sound is muted.

Set VOLUME to the “m” position, press

MUTE to cancel a mute and adjust the volume.

Play a source whose signals this unit can

reproduce.

Digital signals other than PCM audio and the

signals encoded with Dolby Digital or DTS

which this unit cannot reproduce are being input

to this unit by a CD-ROM, etc.

The sound suddenly

goes off.

The protection circuit has been activated

because of a short circuit, etc.

Set the unit in the standby mode and then turn

on to reset the protection circuit.

The SLEEP timer has functioned.

Turn on the power, and play the source again.

Refer to

page

APPENDIX

Incorrect DSP program is selected. Select the appropriate program.

The source encoded with Dolby Digital or DTS

does not have a center channel signal.

No sound from the rear

speakers.

The output level of the rear speakers is set to

minimum.

Raise the output level of the rear speakers.

A monaural source is being played with the PRO

LOGIC/Normal or PRO LOGIC/ENHANCED

program.

Select another DSP program suitable for the

monaural source.

—

12, 13

—

25, 26, 27

The unit fails to turn on

when STANDBY/ON is

pressed, or enters in the

standby mode soon after

the power has been

turned on.

—

0110V496RDS50-55_EN 1/6/0, 11:08 AM50

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

SYMPTOM CAUSE REMEDY

Incorrect cable connections. Firmly connect the audio plugs. If the problem

persists, the cables may be defective.

No connection from the turntable to the GND

terminal.

Make the GND connection between the

turntable and this unit.

The volume level cannot

be increased, or the

sound is distorted.

The component connected to the TAPE/MD

OUT (REC) terminals of this unit is in the

standby mode.

Turn on the power to the component.

The sound effect cannot

be recorded.

It is not possible to record the sound effect by a

tape deck or MD recorder connected to the

TAPE/MD OUT (REC) terminals of this unit.

The DVD/LD, TV/digital TV

or satellite tuner source

cannot be recorded by

tape deck, MD recorder

or VCR connected to this

unit.

The DVD/LD player, TV/digital TV or satellite

tuner is connected to the unit only through the

digital terminals.

Make additional connections between the

analog terminals.

Previously preset

stations can no

longer be tuned in.

The unit has been disconnected for a long

period.

Re-store the stations.

Refer to

page

Adjusting this unit by

using SET MENU, TIME/

LEVEL or TEST cannot

be performed.

“MEM. GUARD” in the SET MENU is set to

the ON position.

Set “MEM. GUARD” to the OFF position.

■ Tuner

SYMPTOM CAUSE REMEDY

FM stereo reception

is noisy.

The characteristics of FM stereo broadcasts

may cause this problem when the transmitter is

too far away or the antenna input is poor.

Check the antenna connections.

Try using a high-quality directional FM

antenna.

Use the manual tuning method.

There is distortion,

and clear reception

cannot be obtained

even with a good FM

antenna.

There is multipath interference.

Adjust the antenna position to eliminate

multipath interference.

The desired station

cannot be tuned in

with the automatic

tuning method.

The station is too weak.

Use the manual tuning method.

Use a high-quality directional FM antenna.

The desired station

cannot be tuned in

with the automatic

tuning method.

The signal is weak or the antenna connections

are loose.

Tighten the AM loop antenna connections and

orient it for best reception.

Use the manual tuning method.

Refer to

page

There are continuous

crackling and hissing

noises.

Noises result from lightning, fluorescent lamps,

motors, thermostats and other electrical

equipment.

Use an outdoor antenna and a ground wire. This

will help somewhat, but it is difficult to

eliminate all noise.

A “humming” sound can

be heard.

The volume level is low

while playing a record.

The record is being played on a turntable with an

MC cartridge.

The turntable should be connected to the unit

through the MC head amplifier.

TROUBLESHOOTING

Select the BOTH position.

12, 13

—

The source does not contain low bass signals

(below 90 Hz).

No sound from the

subwoofer.

“BASS OUT” in the SET MENU is set to the

SW or MAIN position when playing a 2-channel

source.

10, 28

11, 28

—

There are buzzing and

whining noises

(especially in the

evening).

A TV set is being used nearby.

Move this unit away from the TV.

—

0110V496RDS50-55_EN 1/6/0, 11:08 AM51

■ Remote control

This unit is in the standby mode. Turn on the power of the unit.

SYMPTOM CAUSE REMEDY

Refer to

page

The remote control does

not work.

Direct sunlight or lighting (from an inverter

type of fluorescent lamp, etc.) is striking the

remote control sensor of this unit.

Reposition the unit.

The batteries are weak. Replace all batteries with new ones.

The unit or other

component cannot be

controlled.

The component to be controlled has not been

selected.

Press one of the component selector buttons

which corresponds to the component to be

controlled.

The manufacturer’s code has not been set

properly.

Enter the code again.

Try setting another code for the same

manufacturer.

■ Others

SYMPTOM CAUSE REMEDY

Refer to

page

The sound is degraded

when listening with

headphones to a tape

deck or CD player

connected to this unit.

There is noise

interference from digital

or high-frequency

equipment, or the unit.

The unit is too close to the digital or high-

frequency equipment.

Move the unit further away from such

equipment.

■ When playing back a source encoded with DTS

Refer to

page

A loud hissing noise is

heard when playing back

a source encoded with

DTS.

The player which plays back the source is not

connected to a digital audio signal input

terminal of this unit.

The player must be connected to a digital audio

signal input terminal of this unit besides the

analog audio signal terminal connections.

The input mode is set to ANALOG on this unit. Set a proper input mode to turn on the built-in

DTS decoder.

A percussive noise is

heard when playing back

a source encoded with

DTS.

If the input mode is set to AUTO, depending on

some sources, there may be a noise heard while

this unit is identifying the format of the input

signal.

Set the input mode of the currently selected

input source to DTS.

No sound is heard when

playing back a source

encoded with DTS, even

if the input mode is set

to AUTO on this unit.

The built-in DTS decoder does not function

because the player has a digital volume control

and it is set at a position other than

“maximum,” “neutral” or “ineffective.”

Set the player’s digital volume control at the

maximum, neutral or ineffective position.

No sound is heard when

playing back an MD or

DAT on which has been

recorded a source

encoded with DTS.

A source encoded with DTS cannot be recorded

on an MD or DAT.

No sound is heard when

playing back a source

(CD, etc.) even if the

currently selected input

mode is AUTO.

In the AUTO mode, the DTS-decoding mode

cannot be automatically changed to the normal

(PCM) digital signal input mode.

Set the input mode to AUTO again.

Notes

• It is necessary to use a DTS decoder to play back a source encoded with DTS, so the player which plays back the source must be connected

to a digital audio input terminal of this unit in the way described in this manual. If this connection is not made or only a D-to-A converter is

being used without using a DTS decoder, only a loud hissing noise will be heard when you play back the source.

• If you make a search (or skip, etc.) operation while playing back a source encoded with DTS, the “t” indicator goes off. This is because

this unit automatically changes the DTS-decoding mode to the standard (PCM) digital signal input mode to prevent a noise from being

output.

TROUBLESHOOTING

—

0110V496RDS50-55_EN 1/6/0, 11:08 AM52

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

SPECIFICATIONS

AUDIO SECTION

• Minimum RMS Output Power

20 Hz to 20 kHz, 0.06% THD, 8 ohms

Main L/R, Center, Rear L/R ......................................... 70 W*/65 W

1 kHz, 0.09% THD, 8 ohms

Main L/R, Center, Rear L/R ....................................... 80 W*/70 W

• Maximum Output Power (EIAJ)

1 kHz, 10% THD, 8 ohms ........................................................ 100 W

• DIN Standard Output Power

1 kHz, 0.7% THD, 4 ohms ....................................................... 100 W

• IEC Output Power

1 kHz, 0.06% THD, 8 ohms ....................................................... 70 W

• Dynamic Power (IHF)

8/6/4/2 ohms .................... 100/120/140/160 W*, 90/110/130/150 W

• Damping Factor

20 Hz to 20 kHz, 8 ohms ................................................................ 60

• Frequency Response

CD etc. to MAIN L/R................................ 20 Hz to 20 kHz, ±0.5 dB

• Total Harmonic Distortion (20 Hz to 20 kHz)

CD etc. to MAIN L/R, 1/2 power, 8 ohms ............................ 0.025%

• Signal-to-Noise Ratio (IHF-A Network)

CD etc. to MAIN L/R

(150 mV, Input Shorted) ........................................................ 96 dB

(250 mV, Input Shorted) ...................................................... 100 dB

• Residual Noise (IHF-A Network)

MAIN L/R .............................................................................. 150 µV

• Input Sensitivity/Impedance

CD etc.................................................................. 150 mV/47 k-ohms

EXT. DECODER......................................... 150 mV/40 – 47 k-ohms

• Output Level/Impedance

REC OUT ........................................................... 150 mV/1.2 k-ohms

SUBWOOFER ....................................................... 4.0 V/1.2 k-ohms

PHONES ................................................................. 0.47 V/390 ohms

• Channel Separation (Vol. –30 dB)

CD etc. (Input 5.1 k-ohms Terminated, 1 kHz/10 kHz)

..................................................................................... 60 dB/45 dB

• Tone Control Characteristics

BASS: Boost/cut .......................................................... ±10 dB/50 Hz

TREBLE: Boost/cut ................................................... ±10 dB/20 kHz

* for U.S.A. and Canada models

VIDEO SECTION

• Video Signal Type ...........................................................NTSC or PAL

• Video Signal Level ...................................................... 1 Vp-p/75 ohms

• Signal-to-Noise Ratio .................................................................. 50 dB

• Monitor Out Frequency Response.................... 5 Hz to 10 MHz, –3 dB

FM SECTION

• Tuning Range .................................... 87.5/87.50 to 107.9/108.00 MHz

• Usable Sensitivity (DIN)

Mono (S/N 26 dB) ................................................................... 0.9 µV

Stereo (S/N 46 dB) ................................................................... 28 µV

• Selectivity (two signals, 40 kHz Dev., ±300 kHz) ...................... 55 dB

• Signal-to-Noise Ratio (Mono/Stereo)

DIN ................................................................................. 75 dB/69 dB

IHF ................................................................................. 81 dB/75 dB

• Harmonic Distortion (1 kHz)

Mono/Stereo ........................................................................ 0.1/0.2%

• Stereo Separation (1 kHz) ........................................................... 48 dB

• Frequency Response ........................................ 20 Hz to 15 kHz, ±1 dB

• Antenna Input ......................................................75 ohms, Unbalanced

AM SECTION

• Tuning Range ............................................530/531 to 1,710/1,611 kHz

• Usable Sensitivity ................................................................. 300 µV/m

• Signal-to-Noise Ratio ...................................................................52 dB

• Antenna ........................................................................... Loop antenna

GENERAL

• Power Supply

[U.S.A. and Canada models] .................................. AC 120 V, 60 Hz

[Europe, U.K. and Singapore models] .................... AC 230 V, 50 Hz

[Australia model]..................................................... AC 240 V, 50 Hz

[China model]......................................................... AC 220 V, 50 Hz

[General model].............................AC 110/120/220/240 V, 50/60 Hz

• Power Consumption ...................................................... approx. 220 W

• AC Outlets (100 W max. total)

[U.K. and Australia models] ..................................... 1 (SWITCHED)

[Other models].......................................................... 2 (SWITCHED)

• Dimensions (W x H x D)

.....................435 x 151 x 391 mm (17-1/8’’ x 5-15/16’’ x 15-3/8’’)

• Weight ............................................................................ 10 kg (22 lbs.)

• Accessories ................................................................ AM loop antenna

.......................................................................... Indoor FM antenna

.....................75-ohm/300-ohm antenna adapter (U.K. model only)

........................ Antenna adapter (U.S.A. and Canada models only)

.................................................................................Remote control

........................................................................................... Batteries

Specifications are subject to change without notice.

0110V496RDS50-55_EN 9/28/0, 4:42 PM53

GLOSSARY

CINEMA DSP

■ Dolby Surround

Dolby Surround uses four discrete channels and five

speakers to reproduce realistic and dynamic sound effects:

two main channels (left and right), a center channel for

dialog, and a rear channel for special sound effects. The rear

channel reproduces sound within a narrow frequency range.

Most video tapes and laser discs include Dolby Surround

encoding, as do many TV and cable broadcasts. The Dolby

Pro Logic decoder built into this unit employs a digital

signal processing system that stabilizes each channel for

even more accurate sound positioning than is available with

standard analog processors.

■ Dolby Digital

Dolby Digital is a digital surround sound system that

provides completely independent multi-channel audio to

you. Dolby Digital provides five full-range channels in what

is sometimes referred to as a “3/2” configuration: three front

channels (left, center and right), and two surround channels.

A sixth bass-only effect channel is also provided for output

of LFE (low frequency effect), or low bass effects that are

independent of other channels. (This is called the “LFE

channel”.) This channel is counted as 0.1, thus giving rise to

the term 5.1 channels in total.

The wide dynamic range of sound reproduced by the five

full-range channels and precise sound orientation by digital

sound processing provides listeners with excitement and

realism that have never been experienced before.

■ DTS (Digital Theater System)

Digital Surround

DTS was developed to replace analog soundtracks of

movies with six discrete channels of digital soundtracks,

and it is now installed in many theaters around the world.

The DTS digital playback system changed the way we

experienced movies in theaters with six discrete channels of

superb digital audio.

DTS technology, through intense research and development

has made it possible to deliver similar encode/decode

discrete technology to home audio surround-sound

entertainment.

DTS Digital Surround is an encode/decode system which

delivers six channels of master-quality, 20-bit audio;

technically, it is 5.1 channels, which means 5 full-range

(left, center, right and two surround) channels, plus a

subwoofer (LFE) channel (as “0.1”). It is compatible with

the 5.1 speaker configurations that are currently available

for home theater systems.

■ CINEMA DSP

The Dolby Surround and Dolby Digital sound and DTS

systems show their full ability in a large movie theater,

because movie sounds are originally designed to be

reproduced in a large movie theater that uses a multitude of

speakers. Trying to create a sound environment similar to

that of a movie theater in your home is difficult because of

the room size, material inside the walls, the number of

speakers, and so on. In other words, your listening room is

very different from a movie theater.

However, YAMAHA DSP technology allows you to create

nearly the same sound experience as that of a large movie

theater in your home by compensating for the lack of

presence and dynamics in the listening room with original

digital sound fields combined with Dolby Surround, Dolby

Digital or DTS Digital Surround sounds.

The YAMAHA “CINEMA DSP” logo indicates those

programs that are created by the combination of YAMAHA

DSP technology and Dolby Surround, Dolby Digital or

DTS.

■ LFE 0.1 Channel

This channel is for reproduction of low bass signals. The

frequency range for this channel is 20 Hz to 120 Hz. This

channel is called the channel 0.1 because it only reproduces

a low frequency range compared to the full-range from

20 Hz to 20 kHz that is reproduced by the 5 channels in a

Dolby Digital or DTS 5.1 channel system.

■ S VIDEO Signal

The S VIDEO signal is separated and transmitted as the Y

signal which indicates the luminance and the C signal which

indicates the chroma of the video signal (composite signal).

Using the S VIDEO terminal eliminates video signal

transmission loss and allows recording and playback of

even more beautiful images.

0110V496RDS50-55_EN 1/6/0, 11:08 AM54

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

INDEX

Accessories .......................................................................... 2

AC outlet ........................................................................... 17

Antennas ...................................................................... 10, 11

BALANCE ........................................................................ 21

BGV (background video) function .................................... 21

Canceling sound effect ...................................................... 24

CINEMA DSP ............................................................. 27, 54

Connections

Antennas................................................................ 10, 11

Audio components (tape deck/MD recorder, CD player

and turntable) .............................................................. 12

Digital connections...................................................... 13

Speakers ...................................................................... 15

TV monitor .................................................................. 13

Video components (DVD/LD player, VCR and TV/

digital TV, satellite tuner) ............................................ 13

Delay time (TIME/LEVEL mode) .................................... 40

Display................................................................................. 6

Dolby Digital ..................................................................... 54

Dolby Surround ................................................................. 54

DSP program ............................................................ 24 to 27

DTS Digital Surround ....................................................... 54

External decoder ................................................................ 14

Front panel........................................................................... 4

IMPEDANCE SELECTOR switch ................................... 17

Input mode......................................................................... 22

LFE ........................................................................ 38, 39, 54

Muting ............................................................................... 21

Playing ............................................................................... 20

Preset stations

To recall a preset station .............................................. 30

Exchanging preset stations .......................................... 31

Preset tuning

Automatic preset tuning .............................................. 29

Manual preset tuning................................................... 30

RDS mode

EON function .............................................................. 34

PTY SEEK function .................................................... 33

Recording .......................................................................... 35

Remote control

Basic operations ............................................................ 7

Batteries......................................................................... 2

Component selector................................................. 7, 43

Factory-set code .......................................................... 49

Manufacturer’s codes .......... i (at the end of this manual)

Setup codes.................................................................. 48

SET MENU ....................................................................... 36

Sleep timer......................................................................... 42

Speaker

Output levels (TIME/LEVEL mode) .......................... 40

Output mode (SET MENU) .................................. 37, 38

Speaker balance (test tone).......................................... 18

Placement ...................................................................... 8

STANDBY/ON.................................................................... 4

Test tone....................................................................... 18, 19

Tone controls ..................................................................... 21

Tuning

Automatic tuning......................................................... 28

Manual tuning ............................................................. 28

0110V496RDS50-55_EN 1/6/0, 11:08 AM55

Admiral 0411, 0451, 0911,

1021, 1081

Aiko 0891

Akai 0061, 0101, 0231,

1191, 1351, 1591,

1641, 1791, 1891,

1981

Akura 1331

Alba 1241, 1331, 2361

Albiral 1971

Amstrad 1301, 1511

Anam 1171

Arc En Ciel 0571

Arcam 0571, 0761

Aristona 0751

Arthur Martin 0451, 1641

ASA 0411, 0451, 0521,

0781, 0871, 1021,

1081, 1421, 2051,

2091, 2151, 2551

Astra 1511

Atantic 0761

Atlantic 0761

Atori 1511

Audiosonic 1181, 1321, 1511

Ausind 0491, 1411

Autovox 0091, 0351, 0481,

0491, 0601, 0781,

0951, 1051, 1081,

1391, 1421

Baird 1101, 1351

Bang & Olufsen 1081

Basic Line 1321, 1331

Bauer 1451

Baur 0041, 0061, 0121,

0131, 0221, 1561

Beko 2491, 2501

Blaupunkt 0221, 0231, 0241,

0251, 0471, 0741,

2201, 2211, 2221,

2231, 2241, 2261,

2571, 2581

Brandt 0571, 0651, 0731,

0901, 1821

Brionvega 1021, 1051, 1081

Britannia 0761

Bruns 0821, 0991, 1021,

1081

BSR 0391, 0691, 1621,

1901, 1981

Bush 0451, 1241, 1331,

1641, 1741, 2131,

2151

Bush (UK) 0481, 1561, 1611

Candle 0791

Century 1021, 1081

CGE 0491, 0811, 0981,

1401, 1531, 1611,

1621, 1981, 2201,

2251, 2271

Citizen 0791

Clarivox 0821, 0961, 1971

Clatronic 1181, 1331

Concerto 0791

Condor 0761

Contec 0151, 1171

Continental Edison 0571, 0651,

0901

Craig 1171

Crosley 0021, 0491, 1021,

1081, 1401, 1981,

2201, 2251, 2271

Crown 2541

Ctc Clatronic 0261

CXC 1171

Daewoo 0101, 1501, 1511,

2611

Dansai 0101

Decca 0271, 0581, 0601,

0971, 1101, 1691

Decca (UK) 0271, 0581, 0601,

1101, 1681

Degraaf 0451, 1351

Dixi 0991, 1511

Domeos 0101

Doric 1031

Dual 0091, 0601, 1611,

1641, 2101

Dual-Tec 0601, 1511, 1621,

2111

Dumont 0261, 0521, 0781,

1021, 1081, 1981,

2121, 2151

Dynatron 0101

Elbe 1551, 1971, 2031

Electro Tech 1511

Elektronska 0771

Elman 0261, 1621

Elta 1511

Emerson 0921, 1021, 1081,

1121, 1171, 1261,

1301

Erres 0101

Etron 1981

Europhon 0261, 0581, 0601,

0771, 1091, 1621,

2001

Fenner 0101, 1511

Ferguson 0281, 0371, 0551,

0651, 0781, 0861,

0881, 1131, 1181,

1361, 1461, 1971,

1991, 2281, 2311,

2341

Fidelity 0451, 0761, 2281

Fidelity (UK) 0561, 0591, 1931,

2281

Filmnet 1141

Finlandia 0451, 2321

Finlux 0021, 0261, 0491,

0521, 0781, 0811,

0871, 1081, 1411,

1421, 1981, 2051,

2091, 2121, 2151,

2551

Hitachi 0001, 0011, 0031,

0081, 0141, 0291,

0331, 0341, 0451,

0601, 0631, 0701,

1281, 1561, 1601,

1821, 1831, 1841,

1861, 1871, 1881,

1891, 1941, 1981,

2051, 2321, 2341

Hyper 0591, 0601, 1511,

1621

Imperial 0451, 0491, 0811,

0981, 1401, 1611,

1621, 2201, 2251,

2271

Ingersol 1511

Inno Hit 0581, 0601, 0841,

1101, 1331, 1371,

1511, 2011

Innovation 2591, 2601, 2611,

2621, 2641, 2651,

2661, 2711, 2721,

2761, 2771, 2781

Interfunk 0031, 0041, 0061,

0121, 0181, 0451,

0491, 1081, 1641,

1791, 1821, 1981,

2231

Irradio 0491, 1321, 1331,

1371, 1411, 1511,

2011

Isukai 1331

ITT 0031, 0041, 0051,

0061, 0071, 0081,

0181, 0411, 0451,

0491, 1241, 1291,

1351, 1501, 1601,

1641, 1741, 1921,

1981, 2091, 2331,

2431

ITT-nokia 0031, 0041, 0051,

0061, 0071, 0081,

0181, 0411, 0451,

0491, 1241, 1291,

1351, 1501, 1601,

1641, 1741, 1921,

1981, 2091, 2331,

2431

JVC 0071, 0721, 1441,

1581, 1591, 1741,

1791

Kaisui 0591, 1321, 1331

Kamosonic 0601

Karcher 0591, 0601, 0841,

1091, 1321, 1511,

1561, 2051

Kawasho 0761

Kendo 0261

Kennedy 0021, 0351, 0951,

1981

LIST OF MANUFACTURER’S CODES

LISTES DES CODES FABRICANT

VERZEICHNIS DER HERSTELLERCODES

LISTA ÖVER TILLVERKARKODER

ELENCO DEI CODICI DEL FABBRICANTE

LISTA DE CÓDIGOS DE FABRICANTES

LIJST VAN CODES VAN FABRIKANT

First Line 1981

Fisher 0021, 0091, 0141,

0511, 0601, 0801,

0821, 0981, 1021,

1081, 1981, 2091

Forgestone 2281

Formenti 0451, 0491, 0761,

1081, 1451, 1541,

1981

Formenti-phoenix 0021, 0431,

0451, 0591,

1411

Fortress 1081

Frontech 0451, 1181, 1981

Fujitsu 1261

Funai 0391, 0691, 1171,

1181, 1261

Futuretech 1171

GBC 0021, 0141, 1321,

1511, 1621, 1981

GEC 0451, 1101, 1281,

2321

GEC (UK) 0031, 0081, 0581,

0601, 1101, 1281,

1561

Geloso 0021, 0411, 0451,

1321, 1511, 1621,

1981

General Technic 2681

Genexxa 0451, 1331

GoldStar 0591, 0601, 0761,

0791, 1371, 1491,

1511, 1561, 1621,

1641

Goodmans 0141, 1101, 1371,

1641, 2301

Gorenje 0981, 1061

Graetz 0451

Granada 0141, 0451, 0491,

0581, 0601, 1101,

1111, 1351, 1981,

2321

Granada (UK) 0081, 0141, 0451,

0491, 0581, 0601,

1031, 1311, 1521,

1561, 1641

Grundig 0221, 0231, 0471,

0491, 0711, 0741,

1381, 2021, 2041,

2141, 2151

Hanseatic 0021, 0121, 0141,

0431, 0591, 1561

Hantarex 0581

Hemmermann 0061

Hifivox 0331, 0571

Hinari 0071, 0141, 0451,

1261, 1351, 1511,

1641, 1981, 2011

08V496RDS-code 12/24/99, 4:32 PM1

Konka 2701

Korting 0431, 1011, 1021,

1081, 1541

KTV 0601, 1171

Lenoir 0601, 1511

Leyeo 1181

Lifetec 2591, 2601, 2611,

2621, 2641, 2651,

2661, 2671, 2681,

2691, 2711, 2761,

2771, 2781

Loewe Opta 0121, 0131, 0581,

0611, 1081

Logic 1691, 2281

Logik 0551, 1681, 2281

Lowewe 0831

Luma 0351, 0451, 1901

Luxman 0791

Luxman Stereo Tuner 0791

Luxor 0001, 0061, 0181,

0341, 0421, 0451,

0461, 0491, 0601,

0671, 1351, 1371,

1561, 1601, 1911,

1921, 1981

Lyco 1181

Magnadyne 0021, 0061, 0261,

0581, 0641, 0771,

1021, 1081, 1621,

1981

Magnafon 0261, 0491, 0581,

0591, 0641, 0761,

1091, 2001

Manesth 0101

Marantz 0101

Marelli 1081

Mark 0101

Matsui 0061, 0451, 0601,

0691, 1101, 1151,

1241, 1271, 1301,

1511, 1561, 1681,

1691

Maximal 0071, 1981

McMichael 1281

Medion 2591, 2601, 2611,

2621, 2641, 2651,

2661, 2671, 2681,

2691, 2711, 2721,

2761, 2771, 2781

Memorex 1511

Metz 0231, 0741, 1001,

1041, 1081, 1481,

2071, 2081

MGA 1231

Micromaxx 2591, 2621, 2641,

2651, 2711, 2761,

2771, 2781

Minerva 0221, 0231, 0491,

1381, 2141, 2151

Mistral 2281

Mitsubishi 0141, 0201, 0231,

0661, 1191, 1201,

1231, 1671, 1691,

1741

Mivar 0491, 0501, 0581,

0591, 0761, 0771,

1371, 1431, 2031

MTC 0791

Multitech 0261, 0581, 0601,

0641, 0981, 1321,

1511

Murphy 0451, 2091

Murphy (UK) 0081, 1031

N.E.I. 0101, 0961

NAD 1341

NEC 0141, 1711, 1721,

1731

Neckermann 0451, 0601, 0981,

1081, 1561, 1931,

1981, 2211, 2231,

2241

Nediator 0101

Nicamagic 0761

Nikkai 1101, 1331, 1641,

1701, 2011

Nobliko 0261, 0491, 0591,

0641, 1381, 1411

Nogamatic 0571

Nokia 0031, 0041, 0051,

0061, 0071, 0081,

0181, 0411, 0451,

0491, 1241, 1291,

1351, 1501, 1601,

1641, 1741, 1921,

1981, 2091, 2331,

2431, 2461, 2791

Nordmende 0031, 0291, 0331,

0451, 0531, 0541,

0571, 1051, 1131,

1591, 1791, 1811,

1821, 1891, 1941,

2631

Oceanic 0321, 1651, 1981

Oceanic (F) 0031, 0061, 0321,

0441, 1661

Onceas 0601

Onwa 1171

Orion 0061, 0391, 0691,

0851, 1211, 1241,

1251, 1301, 1481,

1511, 1681, 1691,

1981, 2371, 2421

Osaka 2011

Osaki 1101, 1331, 2011

Osume 0151

Otto Versand 0021, 0121, 0141,

0221, 0601, 1561,

1741, 1981

Pael 0591, 1411

Panasonic 0031, 0201, 0211,

0451, 0701, 1311,

1751, 1961, 2561,

2741

Panoramic 2351

Pathe Marconi 0571

Pathe’ Cinema (F) 0431, 0591,

1621, 1661,

1971

Pausa 1511

Pauza 1511

Perdio 0891, 1101

Philco 0021, 0491, 0811,

0981, 1021, 1081,

1401, 1611, 1621,

1751, 2201, 2251,

2271, 2451, 2471

Philips 0101, 0361, 0591,

0621, 0681, 0751,

0761, 1021, 1081,

1281, 2031, 2281,

2291, 2431, 2441,

2511, 2731

Phoenix 1081

Phonola 0751, 1081

Pioneer 0291, 0451, 1341,

1821

Prandoni-prince 0411, 0451,

0491, 0581,

1411

Prandoni-promce 0451, 0491,

0581

Prima 0451

Profex 1981

Protech 0641, 1181, 1981

Quelle 0041, 0061, 0121,

0221, 0231, 0391,

0491, 0521, 0601,

0781, 1371, 1381,

1411, 1421, 1641,

1681, 2051, 2091,

2141, 2151, 2201,

2211, 2231, 2241,

2251, 2271, 2551,

2571, 2581

Radiomarelli 0101, 0451, 0661,

0771, 1081

Radionette 0031, 2051, 2091

Radiola 2291

Rank 0481, 2151

Rbm 2131, 2151

Rbm (UK) 0481

Rediffusion 0451, 0661, 1641,

1981, 2331

Rediffusion (UK) 0061, 0081,

1031

Rex 0071, 0101, 0351,

0411, 0451, 0951,

1901, 2061, 2101,

2111

Rft 0991, 2511

Roadstar 1321, 1511

Rotel 0151

Saba 0291, 0331, 0421,

0451, 0531, 0541,

0571, 0581, 0651,

0731, 0931, 1021,

1071, 1081, 1131,

1791, 1811, 1821,

1891, 1941, 2631

Saccs 1971

Saisho 0451, 0601, 1161,

1241, 1301, 1511,

1671, 1681, 1691

Salora 0011, 0041, 0061,

0071, 0341, 0451,

0671, 1291, 1351,

1521, 1561, 1601,

1641, 1911, 1921,

1931, 1981, 2321

Sambers 0261, 0491, 0581,

0641, 1091, 1371,

1411, 2001

Samsung 0101, 0601, 0841,

0981, 1101, 1181,

1371, 1511, 2011

Sanyo 0141, 0151, 0401,

0601, 0801, 0821,

0981, 1021, 1101,

1111, 1291, 1351,

1691, 1741, 2051,

2091, 2551

SBR 0681, 0751, 1281,

2281

Schaub Lorenz 0451

Schneider 0021, 0071, 0091,

0451, 0511, 0591,

0601, 0751, 1321,

1361, 1621, 1641,

2101, 2111, 2291

Scott 1171, 1261

SEG 0261, 0601, 0821,

0991

SEI 0641, 0691, 1081,

1301, 1481, 1981

Seleco 0071, 0101, 0351,

0411, 0451, 0951,

1901, 2061, 2101,

2111

Sentra 1601

Sharp 0141, 0151, 0191,

1761, 1781

Siarem 0021, 0261, 0581,

0641, 1021, 1081,

1981

Sicatel 1971

Siemens 0151, 0221, 0231,

0451, 0741, 2011,

2201, 2211, 2221,

2231, 2241, 2261,

2571, 2581

Silver 1181

Singer 0021, 0261, 1021,

1081

Sinudyne 0101, 0021, 0061,

0261, 0391, 0641,

0691, 0851, 0941,

1021, 1081, 1241,

1301, 1321, 1481,

1631, 1981

Skantic 0451

Solavox 0451, 1641, 2011

Sonoko 1181, 1511, 0101

Sony 0141, 0171, 1121,

1681, 1691, 2751

Soundesign 1171

SSS 1171

Stern 0071, 0101, 0351,

0411, 0451, 0951,

1901, 2061, 2101,

2111

Sunkai 0691

Supra 0791

Tandberg 0161, 0331, 0611,

1021, 1421, 1771,

1791, 2081

Tandy 0451, 0191, 1331,

1531

Tashiko 0141

Tatung 0271, 0581, 0601,

0971, 1101, 1681,

1691

Tcm 2621, 2641, 2711,

2761, 2771, 2781

Technics 1311

Techwood 0791

Teknika 1171, 1231, 1261

Tele 1141

Teleavia 0571, 0651, 0731,

1821

Telefunken 0291, 0301, 0311,

0551, 0731, 1131,

1471, 1591, 1791,

1801, 1811, 1821,

1991, 2161, 2171,

2181, 2191, 2201,

2251, 2271, 2521,

2631

Teletech 1511

Tempest 2381, 2391, 2401,

2411

Tensai 1331, 2091

Texet 0601

Thomson 0331, 0481, 0531,

0571, 0631, 0651,

0731, 0901, 1241,

1571, 1591, 1791,

1811, 1821, 1891,

1941, 2531

Thorn 0741, 0861, 2091,

2251, 2271, 2281

08V496RDS-code 12/24/99, 4:32 PM2

iii

Thorn-Ferguson 0281, 0371, 0551,

0651, 0781, 0861,

0881, 1131, 1181,

1361, 1461, 1971,

1991, 2281

TMK 0141, 0791, 1471

Toshiba 0141, 0381, 0481,

1221, 1271, 1701,

1741, 1851, 2151,

2801, 2811

Trans Continens 0451

Tristar 2281

Triumph 0481, 0581, 2121

Uher 0431, 0451, 0481,

0491, 0511, 1311,

1541

Ultravox 0021, 0261, 0591,

1021, 1081, 1981

Universum 1181, 2051

Univox 1971

Vegavox 0811

Vexa 0101, 1511

Victor 1441, 1591

Videoton 2481

Vortec 0101, 0651

Voxson 0411, 0451, 0491,

1021, 1081

Waltham 0451

Watson 0431, 2201, 2241

Watt Radio 0021, 0061, 0261,

0591, 0641, 0761,

1091, 1971, 1981,

2001

Wega 0141, 1081, 1981

Wega Color 1021

Weltblick 0101

Weston 1621

White Westinghouse 0101, 0261,

0431, 0591,

0761, 1401,

1541

Yoko 0601, 1511

Zanussi 0071, 0101, 0351,

0411, 0451, 0951,

1901, 2061, 2101,

2111

Zoppas 0451

CABLE

Cabletime 1446, 1456, 1476

Clyde Cablevision 1426

Filmnet 1396, 1436

France Telecom 1386

GEC 1426

Jerrold 1416

Movie Time 1466

NSC 1466

Philips 1386

Pioneer 0006

Samsung 1496

Scientific Atlanta 1486, 1506

Starcom 1416

STS 1466

Tele 1436

Tele+1 1436

Teleservice 1406, 1476

Tudi 1376

United Cable 1416

Zenith 1406

SATELLITE TUNER

Akai 1276

Alba 0826, 1276

Amstrad 0166, 0796, 1016,

1026, 1296

Ankaro 0476

Ast 0406

Astra 0126

Barcom 0476

Blaupunkt 0966

Bmc Satellite 0106

British Telecom 1276

Bush 0826

Bush (UK) 0956

Cambridge 0196, 1276

Chaparral 0016, 0696, 1006

Columbus 0616

Connexions 0306, 0426

Discus Elipse 0856, 0866

Diskxpress 0426, 0476

Drake 1516

Echostar 0226, 0236, 0606,

0626, 0666, 0926,

0996, 1046, 1056,

1066, 1106

Elta 1286

Elta Sat 0146

Eurodec 1226, 1236, 1246

Ferguson 0046, 0176, 0186,

0296, 0846, 0956,

1306

Finlux 0976

Fracarro 0026, 0536, 0776

Fuba 0476, 0616, 0636,

1056

Giucar Record 0206, 0336

Grundig 0176, 0946, 0956,

0966

High Performance 0916

Hirschmann 0756, 0966

Hitachi 0446, 0516, 0706,

0946

Icx International 0886

ITT 0066, 0126, 0176,

0446, 1156

ITT/Nokia 0066, 0126, 0176,

0446, 1156

Jeemon 0146

Jerrold 0846, 0986

Johansson 0246

JVC 1276

Kathrein 0116, 0266, 0276,

0366

Kosmos 0266

Kyostar 1036, 1086

Leng 0246

Lifesat 1326, 1346, 1356

Luxor 0126, 0136, 0446,

0466, 0506, 1156

Macab 0356

Maspro 0016, 0116, 0256,

0956

Medion 1326, 1346

Metz 0966

Micromaxx 1326, 1346

Mitsubishi 0966

Morgans 0596

Muratto 0406

NEC 0286, 0316, 0766,

0786, 0836

Network 0046

Nikko 1136, 1146

Nokia 0066, 0126, 0176,

0446, 1156, 1166,

1336

Norsat 0786

Otto Versand 0966

Pace 0046, 0176, 0296,

0936, 0956, 1306

Pace Mss 0946

Palcom 0616, 0686, 0706

Palsat 0396

Paltec 0706

Panasonic 0806, 1306

Pansat 1076

Philips 0326, 0346, 0476,

0956, 1126, 1186,

1196, 1206, 1216,

1306, 1316

Prosat 1176

Ptt Telecom 0306, 0896

Quelle 0966

Radix 1056

Rediffusion 0316, 0786

Rft 1186, 1196, 1206,

1216

Sagem 1256

Sakura 0566, 0816

Salora 0066, 0126, 0136,

0446, 0456, 0486,

0496, 0576

Samsung 0746, 0756

Sat 0406

Satcom 0896

Sateco 0646

Sector 1266

Sedea 1096

Sentra 0416

Siemens 0896, 0966

Sintrack 0906

Skylab 0476

Skyscan 0876

Sony 0736, 0946

Stella 0306

Strong 0156, 0396, 1036,

1086

Stv 0636

Tandberg 1116, 1366

Tandy 0916

Tantec 0616

Tatung 0516, 0546

Technisat 0086, 0096, 0526,

0556, 1056

Telecom 0306

Telemax 0586

Thorn-Ferguson 0046, 0076,

0176, 0186,

0956

Toshiba 0946

Triad 0406

Uniden 0036, 0216, 0676,

0716, 0726

US Electronics 0886

Vortec 0756, 1036, 1076

Vtech 0436

Winersat 0246

Wisi 0056, 0356, 0376,

0386, 0406, 0656,

1056, 1156

Wolsey 0916

Zehnder 0266, 0406

Zender 0406

VCR

Aiwa 0042, 0352, 0432

Akai 0042, 0422, 0492,

0582, 0612, 0642,

0652, 0762, 0912

Alba 0002, 0112, 0282,

0332, 0342, 0972

Amstrad 0322, 0432, 0452

Anitech 0002

Anitsch 1002

ASA 0012, 0052

Audiosonic 0002

Baird 0042, 0282, 0492

Bang & Olufsen 0042

Baur 0052, 0062, 0812

Blaupunkt 0062, 0092, 0252,

0462, 0672, 0992

Brionvega 0032

Bush 0002, 0282, 0332,

0342, 0512, 0972

Bush (UK) 0812

Capehart 0112

CGE 0042, 0432, 0762

Craig 0072, 0482

Crown 0112, 0282, 0622

Daewoo 0112, 0282, 0622

Dansai 0012

Daytron 0112

Decca 0042, 0052, 0432,

0942

Decca (UK) 0052

Degraaf 0052, 0132, 0432,

0532, 0602

Dixi 0442

Dual 0042, 0632

Dumont 0052, 0432, 0532

Dynatech 0432

Dynatron 0012

Elbe 0122

Elin 0072

Emerson 0012, 0162, 0202,

0432, 0512, 0522

Erres 0012

Ferguson 0042, 0712, 0722,

0852, 0902, 1012,

1022, 1082

Fidelity 0432

Finlandia 0052, 0532

Finlux 0012, 0042, 0052,

0082, 0262, 0382,

0432, 0462, 0492,

0532, 0572, 0602,

0912

First Line 0002, 0912

Fisher 0162, 0482, 0532,

0542, 0572, 0592

Formenti-Phoenix 0012, 0052

Frontech 0112

Funai 0432

GBC 0002

GEC (UK) 0022, 0052

Geloso 0002

General Technic 1172

GoldStar 0012, 0122, 0812,

0952

Goodmans 0002, 0072, 0282,

0432, 0502

Goodmans (UK) 0002

Graetz 0022, 0042

Granada 0052, 0132, 0532,

0572

Granada (UK) 0052, 0092, 0462,

0602, 0812, 0822

08V496RDS-code 12/24/99, 4:32 PM3

Grundig 0052, 0062, 0092,

0232, 0252, 0262,

0752, 0802

Hanseatic 0052, 0812

Harman/Kardon 0122, 0922

Hcm 0002

Hinari 0002, 0202, 0412,

0442, 0522

Hitachi 0042, 0172, 0292,

0432, 0602, 0662,

0812, 1022

Imperial 0072, 0432

Ingersol 0442

Inno Hit 0002, 0052, 0072

Innovation 1142, 1162, 1172

Interfunk 0022, 0052

Irradio 0002, 0012

ITT 0022, 0032, 0042,

0072, 0292, 0492,

0532, 0572, 0762

ITT-Nokia 0022, 0032, 0042,

0072, 0292, 0492,

0532, 0572, 0762

Jensen 0042

JVC 0042, 0102, 0142,

0272, 0742, 0762,

0782, 0902

Karcher 0052, 0072, 0812

Kendo 0492

Kenwood 0042, 0142, 0572

Lifetec 1142, 1162, 1172

Lloyd 0432

Loewe Opta 0052, 0092, 0152

Logik 0002, 0072, 0442

Luma 0162

Luxor 0492, 0572, 0812

M Electronic 0432

Magnadyne 0052

Magnasonic 0572

Manesth 0012

Marantz 0012, 0052, 0092,

0122, 0502

Mark 0012

Marta 0012

Matsui 0012, 0442, 0512,

0522, 0812, 0972

Medion 1142, 1162, 1172

Memorex 0012, 0132, 0432,

0482, 0532, 0572

Metz 0062, 0092, 0932

MGA 0912

Micromaxx 1142, 1162, 1172

Minerva 0062, 0092, 0252

Minolta 0172, 0602

Mitsubishi 0052, 0062, 0142,

0912, 0922

MTC 0072, 0432

Multitech 0002, 0052, 0062,

0282, 0432

Murphy 0432

N.E.I. 0012, 0052

National 0462

NEC 0042, 0122, 0142,

1202

Neckermann 0032, 0042, 0052,

0072, 0092, 0202,

0522, 0572, 0762,

0812

Nikkai 0112

Nobliko 0092

Nokia 0022, 0032, 0042,

0072, 0292, 0492,

0532, 0572, 0762,

1152

Nordmende 0042, 0102, 0142,

0192, 0222, 0242,

0392, 0402, 0632,

0732, 0742, 0762,

0782, 0792, 0832,

0842, 0872

Olympus 0462

Optonica 0132, 0502

Orion 0162, 0202, 0312,

0442, 0512, 0522,

0982

Osaka 0432

Osaki 0002, 0012, 0432

Otto Versand 0052, 0062, 0812

Panasonic 0022, 0212, 0462,

0672, 0992, 1092,

1102, 1182

Pentax 0172, 0602

Perdio 0432

Philco 1062

Philips 0052, 0082, 0092,

0152, 0182, 0362,

0372, 0382, 0472,

0502, 1072

Phonola 0052, 0152

Pilot 0012

Pioneer 0052, 0142, 0372,

0472

Portland 0112

Proline 0432

Pye 0052, 0152

Quartz 0572

Quelle 0012, 0032, 0042,

0052, 0062, 0072,

0092, 0202, 0462,

0552, 0942

Radionette 0022

Realistic 0012, 0072, 0132,

0432, 0482, 0502,

0532, 0572

Ret 1072

Rex 0042, 0742, 0782

Ricoh 0952

Saba 0042, 0142, 0192,

0222, 0242, 0392,

0632, 0732, 0742,

0762, 0772, 0782,

0792, 0872

Saisho 0162, 0202, 0292,

0442, 0512, 0522,

0972

Salora 0192, 0572, 0812,

0822, 0912

Samsung 0052, 0072, 0622,

0652, 1192

Sansui 0042, 0142

Sanyo 0482, 0532, 0562,

0572

SBR 0052, 0152, 0182

Schaub Lorenz 0022, 0042

Schneider 0002, 0012, 0052,

0072, 0432

SEG 0002, 0072

Sei-Sinudyne 0442

Seleco 0042

Sentra 0112

Sharp 0132, 0502, 0702

Shintom 0002

Siemens 0062, 0092, 0252,

0572

Sinudyne 0052, 0382, 0442,

0932

Sonoko 0282

Sony 0432, 0552, 0682,

0692, 0942, 0952,

0962, 1122, 1132

STS 0602

Sunkai 0512

Sunstar 0432

Sylvania 0432, 0912

Symphonic 0432, 0912

Tandberg 0062, 0162, 0522,

0932

Tashiko 0132, 0432

Tatung 0042, 0052, 0432,

0922

TCM 1142, 1162, 1172

Teac 0042, 0432

Technics 0462

Teknika 0012, 0432

Telefunken 0042, 0192, 0632,

0732, 0742, 0762,

0782, 0882, 0892

Tempest 1032, 1042, 1052

Tenosal 0002

Thomson 0042, 0102, 0142,

0192, 0402, 0632,

0762

Thorn 0042, 0902

Thorn-Ferguson 0042, 0222, 0302,

0712, 0722, 0742,

0762, 0852, 0862,

0872, 0902

TMK 0522

Tonsai 0002

Toshiba 0042, 0622, 0912,

1212

Totevision 0012, 0072

Triumph 0922

Uher 0042, 0072

Ultravox 0032

Unitech 0072

Vector Research 0122

Victor 0042, 0102, 0142

Videon 1162, 1172

Weltblick 0012

White Westinghouse 0032

Xenon 0162

Yoko 0012, 0062, 0072

DVD PLAYER

Akai 0108

JVC 0168

Onkyo 0128

Panasonic 0048

Philips 0188

Pioneer 0208, 0228

Samsung 0148

Sharp 0068

Sony 0028

Toshiba 0088

Yamaha 0008, 0048

LD PLAYER

Aiwa 0137

Funai 0137

Hitachi 0047

Magnavox 0077

Panasonic 0027

Pioneer 0037

RCA 0067

Realistic 0137

Samsung 0017, 0087

Sony 0057, 0097, 0107,

0117

Victor 0127

Yamaha 0007

CD PLAYER

Accuphase 0315

Adc 0865

Adcom 0785, 1015

Akai 0115, 0125, 0725,

0735, 0745, 0935,

1155

Arcam 1875

Arcam-Rotel 0165

Audio-Technica 0835

Audiosonic 0155

Awia 1105, 1235, 1245,

1765, 1915, 1935

BSR 0875

California Audio Lab 1075

Carrera 0555, 0875

Carver 0825, 1415

Cyrus-Rotel 0205

Denon 0045, 0955, 1045,

1595, 1795, 1805

Dual 1005

Elin 0185

Emerson 1015, 1285, 1675

Fisher 0105, 0595, 0605,

0825, 1165, 1175

Genexxa 0525, 0825, 0855,

0875, 0995, 1265,

1285, 1345, 1355,

1485, 1575, 1675,

1715, 1825

GoldStar 0555, 1185, 1195,

1585

Grundig 0175

Harman Kardon 0495, 0565, 0325,

1135, 1145, 1155

Hitachi 0065, 0585, 0685,

0945, 1005, 1015,

1225, 1545

Innovation 1995, 2005, 2015

ITT-Nokia 0185

JVC 0385, 0395, 0455,

0575, 0585

Karcher 0485

Kenwood 0025, 0055, 0145,

0215, 0595, 0675,

0695, 0705, 0715,

0925, 1355, 1485,

1575, 1675, 1715,

1825

Korting 0175

Lifetec 2015

Light Control 1155, 1645, 1655,

1665

Linn 0165, 1875

Luxman 0265, 0275, 0795,

0805, 1295, 1305,

1555, 1925

Luxor 0185, 1895, 1905

Magnavox 1865, 1875

Marantz 0165, 0175, 0545,

0665, 1275, 1335,

1405, 1505, 1875,

1955

Matsushita 1095, 1605

MCS 0535

Medion 0075, 1995, 2005,

2015

Memorex 0525, 1015, 1265,

1275, 1285, 1675

MGA 1125

Micromaxx 2015

Mission 0165, 1875

Mitsubishi 1125, 1205

08V496RDS-code 12/24/99, 4:32 PM4

NAD 0255, 0285, 0295,

0305, 0345, 0135,

0755, 0765, 1315,

1325

Nakamichi 0635, 0645, 1565

NEC 0405, 0535, 0775,

0785

Neckerman 0155, 0225

Nikko 0835, 1165

Oceanic 0185

Okano 0155, 0225

Onkyo 0885, 1385, 1425,

1455, 1515

Panasonic 1055, 1075, 1615,

1625

Philips 0165, 0175, 0195,

1865, 1875

Pioneer 0095, 0335, 0425,

0435, 0445, 0525,

0855, 1035, 1945

Proton 0905, 1875

Quasar 1075

Radiola 1845, 1855

Radiotone 0485

Realistic 0825, 1015, 1265,

1275, 1285, 1575

Rotel 1875

Saba 1005

SAE 1875

Salora 0185

Sansui 0415, 0965, 0975,

0985, 1255, 1675,

1875

Sanyo 0625, 0825, 0845,

0915

Schneider 1845, 1855

Scott 1285, 1675

Sharp 0025, 0035, 1025,

1115, 1275, 1635,

1785, 1815, 1825,

1835

Sherwood 1275, 1445

Siemens 1085

Signature 1155

Sony 0345, 0355, 0365,

0375, 0865, 1685,

1695, 1705, 1715,

1725, 1735, 1745

Sytvania 1875

Tandberg 1885

Tashiko 1525

TCM 1985, 2015

Teac 0235, 0245, 1275,

1365, 1375, 1395,

1435, 1465, 1475

Technics 0465, 0475, 1065,

1075, 1625

Telefunken 1005

Theta Digital 1865

Thomson 1005

Toshiba 0755, 0765

Vector Research 0555, 0865

Victor 0575

Yamaha 0005, 0015, 0895,

1815

MD RECORDER

Yamaha 0024

TAPE DECK

Akai 0124

Denon 0204

Grundig 0134

Harman 0044

JVC 0194

Kenwood 0164

Korting 0134

Luxman 0054, 0064, 0074,

0084

Marantz 0134, 0144

NAD 0174

Onkyo 0184

Philips 0134, 0144, 0154

Pioneer 0034, 0114

Sony 0094, 0104

Yamaha 0004, 0014

08V496RDS-code 12/24/99, 4:32 PM5

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia ID V502870-2

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

RX-V496RDS

Natural Sound AV Receiver

Ampli-tuner audio-vidéo

RX-V496RDS

G B

00RX-V496RDS-cv(ML) 9/28/0, 4:41 PM1

DISPLAY (MD)

SLEEP

EFFECT

MUTE

TV VOLUME

VOLUME

POWER

REC/PAUSE

PLAY

DIR A (TAPE)

SKIP– (MD)

REWIND (TAPE)

SEARCH (MD)

Input selector

buttons

PAUSE (MD)

DECK A/B (TAPE)

DIR B (TAPE)

SKIP+ (MD)

STOP

FAST FORWARD (TAPE)

SEARCH (MD)

SET

SLEEP

TEST

A/B/C/D/E

EFFECT

PRESET+/–

MUTE

TV VOLUME

VOLUME

PRG+,

PRG–

+/–

POWER

TIME LEVEL

Input selector

buttons

TV INPUT

DISPLAY

SLEEP

EFFECT

MUTE

TV VOLUME

VOLUME

POWER

PLAY

SKIP–

Input selector

buttons

PAUSE

TV INPUT

SKIP+

STOP

Quick Reference Card

AMP(TUNER)

TAPE/MD CD DVD/LD

DISC SKIP+/–

DISPLAY

SLEEP

EFFECT

MUTE

TV VOLUME

VOLUME

POWER

PLAY

SKIP–

Input selector

buttons

PAUSE

TV INPUT

SKIP+

STOP

DISC SKIP+/–

V503030

DISPLAY

TV SLEEP

EFFECT

CHANNEL

ENTER

MUTE

TV VOLUME

VOLUME

VCR

POWER

VCR REC

Press this button twice to start recording.

Appuyer deux fois sur cette touche pour commencer l’enregistrement.

Drücken Sie diese Taste zweimal, um die Aufnahme zu starten.

Tryck två gånger på den här knappen för att börja spela in.

VCR PLAY

VCR

REWIND

CHANNEL CHANNEL

VCR

PAUSE

TV INPUT

VCR STOP

VCR FAST

FORWARD

RETURN

TITLE

CLEAR

INDEX

+10

MUTE

TV VOLUME

VOLUME

DISC SKIP+/–

VCR

CHANNEL+/–

CBL/SAT

CHANNEL+/–

POWER

Numeric buttons

TV INPUT

DISPLAY

TV SLEEP

+100

MUTE

TV VOLUME

VOLUME

CBL/SAT

POWER

MENU SELECT

MENU LEFT

RECALL

MENU UP

TV INPUT

MENU RIGHT

MENU DOWN

Quick Reference Card

DVD MENU

VCR CBL/SAT TV

DISPLAY

TV SLEEP

EFFECT

TV MUTE

TV VOLUME

VOLUME

POWER

VCR PLAY

VCR

REWIND

CHANNEL

VCR

PAUSE

TV INPUT

VCR STOP

VCR FAST

FORWARD

MENU SELECT

MENU LEFT

MENU RIGHT

MENU DOWN

MENU UP

CHANNEL

ENTER

CHANNEL+/–

CHANNEL

ENTER

V503030

VCR REC

Premere due volte questo tasto per iniziare la registrazione.

Presione dos veces este botón para empezar a grabar.

Druk tweemaal op deze toets om met opnemen te beginnen.

Yamaha RX-V496RDS de handleiding

Merk: Yamaha

Model: RX-V496RDS

Categorie: AV-ontvangers

Type: de handleiding

Download PDF

rapport

in andere talen

English: Yamaha RX-V496RDS Owner's manual
italiano: Yamaha RX-V496RDS Manuale del proprietario
français: Yamaha RX-V496RDS Le manuel du propriétaire
Deutsch: Yamaha RX-V496RDS Bedienungsanleitung
dansk: Yamaha RX-V496RDS Brugervejledning
svenska: Yamaha RX-V496RDS Bruksanvisning
Türkçe: Yamaha RX-V496RDS El kitabı
română: Yamaha RX-V496RDS Manualul proprietarului

Yamaha RX-V496RDS de handleiding

Yamaha RX-V496RDS de handleiding

in andere talen

Gerelateerde artikelen

Andere documenten