1
GB
INSTRUCTIONS FOR USE
HG3011CH
20
325 88-9166 Rev. 1-401
Postbus 1033. 6920 BA Duiven. Nederlan
d
2
Congratulations from ATAG
Dear Customer,
Congratulations with your new Hob.
It is important that you become familiar with the functions and features of
the Hob. You should therefore read these operating instructions as they will
help you get the most out of your new Hob.
Pay extra attention to sections marked . These are warning texts to help
you avoid accidents.
Keep the operating instructions. They will come in handy if there is
something you are not sure about, and should accompany the Hob if it is
transferred to a new owner.
The structure of the operating instructions enables you to use them as a
reference manual. The first part of the operating instructions contains a
general description of your new product. Then follows a short introduction
of the things to do before you use the Hob for the first time. The section
“How to use” describes how the Hob is used in everyday life. Use this
section until you are familiar with your new Hob. The section “Cleaning
and Maintenance” provides information on both daily and more thorough
cleaning of the individual components of the Hob. Should problems arise
when you use the Hob, you can look in the section “Before calling service”,
where there are instructions on how to remedy some practical and technical
problems yourself.
Enjoy!
Regards,
19
3
Contents Page no
For the user
Your new aplliance ....................................................................................... 2
Safety information ........................................................................................ 4
Description of the product ......................................................................... 6
Operations .................................................................................................... 7
Burner ring/cover ................................................................................. 8
Ignition electrode (A) ........................................................................... 8
Thermo Sensor (B) ............................................................................... 8
Ignition .................................................................................................. 8
Maintenance and cleaning .......................................................................... 9
Stainless steel surfaces ......................................................................... 9
The gas burner...................................................................................... 9
Service .................................................................................................. 16
Guarantee ........................................................................................... 17
For the installer
Mounting .................................................................................................. 10
Technical data ............................................................................................. 15
Table of contents
1... 2...Step by step
Safety information
Hint and tips
Environmental information
How to read the operating instructions:
18
Important Advice
This appliance has been constructed to
ensure safety. However, repairs
performed by non-specialists could
impair the safety of the appliance. To
ensure safety and prevent any damage,
it is recommended to only allow
people with the appropriate
professional skill to repair this
appliance. We recommend that your
have this appliance repaired and/or
checked only by a your local
professional serviceman or by ATAG
Service and use only original ATAG
parts.
4
Safety information
These warnings are provided in the
interests of your safety. Ensure you
fully understand them before installing
or using the appliance. Your safety is of
paramount importance. If you are
unsure about the meaning of these
warnings contact the Customer Care
Department for assistance.
Installing
Do not install the hob if the ceramic
glass is damaged or cracked.
This hob must be installed according to
the instructions supplied. Any
installation work must be undertaken
by a qualified competent person.
Do not alter the specifications or
attempt to modify the appliance in any
way.
During Use
The hob is intended for domestic
cooking only. It is not designed for
commercial/industrial purposes.
Ensure that all the control knobs are in
the OFF position when not in use.
Do not use the hob if it is damaged in
any way, contact your local ATAG
Service Centre.
Never use plastic or aluminium dishes
on the hob.
4227
Never leave the hob unattended while
deep fat frying, or heating fats and oils.
The appliance is not intended for use
by young children or infirm persons
without supervision.
Child Safety
Young children should be supervised
to ensure that they do not play
with the appliance
The hob gets hot when it is in use.
Children should be kept away until the
hob has cooled.
Maintenance and Cleaning
Only clean this hob in accordance
with the instructions given in this
book.
Service
Repairs carried out by inexperienced
persons may cause injury or serious
malfunction of the appliance. Repairs
must only be carried out by a
qualified/competent person. Contact
your local ATAG Service Centre.
Disposal
Make the hob unusable by cutting off
the cable.
Dispose of any packaging material and
old appliances at an authorised
disposal site.
17
Guarantee
Please refer to the accompanying
guarantee booklet and guarantee card
for guarantee conditions.
5
Description of the product
Burner
Control knob
16
Service
If the hob is not working correctly, please carry out the following checks before
contacting your local ATAG Service Centre.
IMPORTANT: If you call out an engineer to a fault caused by incorrect use or
installation, a charge will be made even if the hob is under guarantee.
If after all these checks, your hob still does not operate correctly, contact your
local ATAG Service Centre.
In-guarantee customers should ensure that the above checks have been made as
the engineer will make a charge if the fault is not a mechanical or electrical
breakdown.
Please note that it will be necessary to provide proof of purchase for any in-
guarantee service calls.
Sympton:
There is no spark when lighting the
gas
When the operating knob is released
the gas ring goes out again
The gas ring burns unevenly
Solution
Check hob is connected to the
electricity supply. Check the fuse and
replace if necessery.
The operating knob has not been
depressed long enough, or has not
been depressed sufficiently.
Ensure the cover has been replaced
correctly, e.g. after cleaning.
6
Burner markings
Symbols at each control knob indicates
which burner is adjusted with the
control knob.
Front Burner
Back burner
Panel markings
Each control knob has a ring showing
the scale of markings.
Off.
Maximum flame
Minimum flame
Operations
15
N L1
240 V
1N + PE
HO5V2V2-F
Yellow/Green: 61 mm +/- 3 mm
Blue and brown: 51 mm +/- 3 mm
Type of gas
Adjusted to natural gas:
G20 - 20 mbar -
G25 - 25mbar
Category and pressures
BE: II
2E+3+
20/25 - 28/37 mbar
FR: II
2E+3+
20/25 - 28/37 mbar
NL: II
2L3B/P
25 - 30 mbar
DE: II
ELL3B/P
20 - 50 mbar
AT: II
2H3B/P
20 - 50 mbar
DK: III
1a2H3B/D
8 - 20 - 30 mbar
Max. nominal load Q na H
S
:
Medium sized burner = 1,9 kW x 1
Large sized burner = 3,0 kW x 1
Total= 4,9 kW
FSD
The unit features fully-secured gas
taps (thermo-fuse).
H
S
= Top calorific value
Q = Nominal load
ID. CE-048AN-0002
Ignition transformer= 50 HZ - 0,6 VA
Radio-noise reduction
This unit observes the current EEC-
directive on radio noise reduction.
This gas appliance is -approved and
marked in accordance with the gas
appliance Directive (90/396/CEE), the
low voltage directive (73/23/CEE) and
the EMC directive (89/336/CEE incl.
the agreed directive changes.
Technical data
Cable type 0,75 mm² HO5 V2V2-F
The Dropinett must be connected via
an external switch with a contact
gap of min. 3 mm (the main switch
may be used)
Wiring
7
Hulpgasring / branderdeksel
In de door de branderkelk samen met de
branderdeksel en hulpgasring gevormde
ruimte vindt de vermenging van gas en
lucht plaats, waardoor het gas op juiste
wijze brandt.
NB.: Het is daarom zeer belangrijk dat
elk branderdeksel c.q. elke hulpgasring
correct op de brander worden
aangebracht.
Als de hulpgasring of het branderdeksel
verkeerd is aangebracht, dan werkt de
brander niet goed, en kunnen de branders
binnen korte tijd beschadigd raken.
Vonkontsteking (A)
Elke brander is voorzien van een
ontstekingselektrode. Zolang u de
bedieningsknop ingedrukt houdt, zorgt
de automatische ontsteking ervoor dat er
een vonk wordt afgegeven tussen de
ontstekingselektrode en het
branderdeksel.
W
armtesensor (B)
Het gasstel is uitgerust met volledig
beveiligde gaskranen (thermische
zekering).
Wanneer de vlam uitgaat, zorgt de
warmtesensor na enkele seconden (max.
90 seconden) automatisch voor afsluiting
van de gastoevoer.
NB.: Gastoevoer vindt altijd plaats
wanneer de bedieningsknop ingedrukt is.
Zie startprocedure.
Brander
Branderdeksel
Inspuiter
14
Gas installation
In accordance with local
requirements for domestic gas
cooking appliances.
Gas installation must only be
carried out by an authorised person.
For gas types see technical data.
Gas connection
The gas intake is situated at the
lower rear of the appliance. The
intake has a ½" conical pipe thread
(see fig 1) If the appliance is to be
connected to a gas cylinder,
conversion with the optional
modification kit will be necessary.
Pressure test
The unit should be pressure-tested
at Max. 150 mbar.
8
1. Depress and turn the control knob
for the burner to the left to max.
flame . (Ignition position)
2. The ignition electrode will emit
sparks, and when the mixture of gas
and air is correct, the burner will be
ignited. If it is not possible to
connect the unit to mains, a
match may be used to ignite the
burner.
3. After starting the burner, press the
control knob for approx. 10
seconds to activate the automatic
thermo-couple (thermo sensor
ready).
5. The burner can now be regulated
between maximum and minimum.
maximum
minimum
Ignition
13
It is not necessary to attach the
reinforcement beam to the work top
surface, as it is held in place by a
specially designed moulding, which is
incorporated in the hob units flanges.
The units externally measured
length
290 mm:
Two-zone ceramic-top electric hob
Two-burner gas hob
Grill
Fryer
Wok
Installation of a single unit
When mounting a single unit, be it a
half-or full size unit, in a
worktopsurface which is thicker than
30 mm, it is necessary to make a
special notch in both sides of the cut-
out hole, as shown in the adjacent
drawing.
The purpose of these notches is to
create space for the electrical cables.
4228
9
Maintenance and cleaning
Stainless steel surfaces
Perform daily cleaning with a slightly
damp cloth. For more severe soiling,
use a liquid cream. Always clean the
steel in the direction of the steel finish.
To ensure that the steel retains its
shine, it is recommended that you use
a polishing agent for stainless steel on
a regular basis. Always polish in the
direction of the steel finish (cross-
wise).
Never use steel wool, metal sponges or
other abrasive cleaning agents.
Cleaning of gas burners
Clean the control panel and knobs plus
the pan grid, as well as burner caps and
rings, with ordinary cleansing agents.
Never use scouring powder, Brillo
pads, metal pads or other scouring
agents on enamelled or painted
surfaces!
Avoid boil-over
If water accidentally gets into the edge
of the burner head (boil-over) the
water must be removed with a lint-free
cloth before the burner is turned on
again.
Likewise, caps and grids must be
thoroughly wiped off before the gas
ring is used again so that the boil-over
does not permanently scar the enamel
or paint.
12
Do not install the hob above drawers.
10
Caution: In order to avoid a hazard this
appliance must be installed according to
these instructions for installation
The hob unit can be mounted in any
type of kitchen with a table surface
whose thickness is between 28 mm and
40 mm.
Fixing
Screw the fixing brackets out to such an
extent that they can be turned in under
the table top. Tighten the brackets on to
the table top with an ordinary
screwdriver.
Cut-out measurements
One rectangular hole is sawn out for the
hob combination chosen.
The depth of the cut-out for any unit is:
490 mm
Length of hole = sum of all units`
externally measured length, less 20 mm.
Mounting of Reinforcement
Beams
A reinforcement Beam, with supporting
flanges at each end, is included with
each two-burner unit. For unit
combinations, a reinforcement beam
must be used between each unit.
Minimum distance
to wall:
150 mm
Minimum distance
to wall (non-
flammable material):
50 mm
Reinforcement
beams
Mounting
11
It is not necessary to attach the
reinforcement beam to the table
surface, as it is held in place by a
specially designed moulding, which is
incorporated in the hob units flanges.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
