Yamaha DPX-1 Handleiding

Merk: Yamaha

Model: DPX-1

Categorie: Dataprojectoren

Type: Handleiding

Deze handleiding is ook geschikt voor

DPX-830

Digital Cinema Projector

Projecteur Cineme Numerique

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

BRUKSANVISNING

GEBRUIKSAANWIJZING

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

DPX-830

Printed in Japan 871D460A20

01EN_DPX-830_EX-cv_new.fm Page 1 Monday, December 26, 2005 8:21 PM

IMPORTANT SAFETY INSTRUCTIONS

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

Please read all these instructions regarding your projector and retain

them for future reference. Follow all warnings and instructions

marked on the projector.

1 Read instructions: All the safety and operating instructions

should be read before the appliance is operated.

2 Retain instructions: The safety and operating instructions

should be retained for future reference.

3 Warnings: All warnings on the appliance and in the operating

instructions should be adhered to.

4 Instructions: All operating instructions must be followed.

5 Cleaning: Unplug this projector from the wall outlet before

cleaning it. Do not use liquid aerosol cleaners.

6 Attachments and equipment: Never add any attachments

and/or equipment without the approval of the manufacturer as

such additions may result in the risk of fire, electric shock or

other personal injury.

7 Water and moisture: Do not use this projector near water or

in contact with water.

8 Accessories: Do not place this projector on

an unstable cart, stand, tripod, bracket or

table. Use only with a cart, stand, tripod

bracket, or table recommended by the

manufacturer or sold with the projector. Any

mounting of the appliance should follow the

manufacturer's instructions and should use a

mounting accessory recommended by the manufacturer.

An appliance and cart combination should be moved with care.

Quick stops, excessive force and uneven surfaces may cause the

appliance and cart combination to overturn.

9 Ventilation: Slots and openings in the cabinet are provided for

ventilation, ensuring reliable operation of the projector and to

protect it from overheating. Do not block these openings or

allow them to be blocked by placing the projector on a bed,

sofa, rug, or bookcase. Ensure that there is adequate ventilation

and that the manufacturer's instructions have been adhered to.

10 Power sources: This projector should be operated only from

the type of power source indicated on the marking label. If you

are not sure of the type of power, please consult your appliance

dealer or local power company.

11 Power-cable protection: Power-supply cables should be

routed so that they are not likely to be walked on or pinched by

items placed upon or against them. Pay particular attention to

cords at plugs, convenience receptacles, and points where they

exit from the appliance.

12 Overloading: Do not overload wall outlets and extension

cords as this can result in a fire or electric shock.

13 Objects and liquids: Never push objects of any kind through

openings of this projector as they may touch dangerous voltage

points or short-out parts that could result in a fire or electric

shock. Never spill liquid of any kind on the projector.

14 Servicing: Do not attempt to service this projector yourself.

Refer all servicing to qualified service personnel.

15 Damage requiring service: Unplug this projector from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

(a) If the power-supply cable or plug is damaged.

(b)If liquid has been spilled, or objects have fallen into the

projector.

the operating instructions. Adjust only those controls that are

covered by the operating instructions. An improper

adjustment of other controls may result in damage and may

often require extensive work by a qualified technician to

restore the projector to its normal operation.

(d)If the projector has been exposed to rain or water.

(e) If the projector has been dropped or the cabinet has been

damaged.

(f) If the projector exhibits a distinct change in performance -

this indicates a need for service.

16 Replacement parts: When replacement parts are required,

be sure that the service technician has used replacement parts

specified by the manufacturer or parts having the same

characteristics as the original part. Unauthorized substitutions

may result in fire, electric shock or other hazards.

17 Safety check: Upon completion of any service or repair to

this projector, ask the service technician to perform safety

checks determining that the projector is in a safe operating

condition.

18 Connection cable: Use the supplied RS-232C and RGB

cables with this equipment to keep interference within the limits

of an FCC/EN55022 Class B device.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

For Canadian customers

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-

003.

IMPORTANT!

Please record the serial number of this unit in the space below.

Model:

Serial No.:

The serial number is located on the bottom of the unit.

Retain this Owner’s Manual in a safe place for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation

Address: 6660 Orangethorpe Avenue

Buena Park, CA90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: Projector

Model Name: DPX-830

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See the owner’s manual instructions if interference to radio reception is suspected.

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void

your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow

all installation instructions. Failure to follow instructions

could void your FCC authorization to use this product in the

USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will not

result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the operation of

other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is

found to be the source of interference, which can be determined

by turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures:

Relocate either this product or the device that is being affected

by the interference.

Utilize power outlets that are on different branch (circuit breaker

or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe

Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

iii

Caution: Read this before operating this unit.

Warning

• This unit must be grounded

• Do not use this projector in a computer room

This projector is not for use in a computer room as defined in

the Standard for the Protection of Electronic Computer/Data

Processing Equipment, ANIS/NFPA 75.

• Unplug immediately if there is something wrong with

your projector

Do not operate if smoke, strange noise or odor comes out of

the projector. It might cause fire or electric shock. If this

happens, unplug immediately and contact your dealer.

• Never remove the cabinet

This projector contains high voltage circuitry. An inadvertent

contact may result in an electric shock. Except as specifically

explained in the owner's manual, do not attempt to service

this product yourself. Contact your dealer when you want to

fix, adjust or inspect the projector.

• Do not modify this projector

It can lead to fire or electric shock.

• Do not continue using this projector if you drop or

break it

Unplug the projector and contact your dealer for inspection.

It may lead to fire if you continue using it.

• Do not face the projector lens towards the sun

It can lead to fire.

• Use correct voltage

If you use incorrect voltage, it can lead to fire.

• Do not place the projector on uneven or unstable

surfaces

Place the projector on a leveled and stable surface only.

• Do not look into the lens when it is operating

It may cause serious eye injury.

• Do not turn off the main power abruptly or unplug the

projector during operation

It can lead to lamp breakage, fire, electric shock or other

trouble. Always wait for the fan to turn off before turning the

main power off.

• Avoid all contact with the air exhaust vents and

bottom plate

The air exhaust vents and bottom plate heat up during

operation and may cause personal injury or damage to other

equipment. Do not touch them, place other equipment in front

of the air exhaust vents, or set the projector on a desk which is

easily affected by heat.

• Do not look into the air exhaust vent when the

projector is operating

Heat, dust, etc. may blow out of it and cause injury to your

eyes.

• Do not block the air intake and exhaust vents

If they are blocked, heat may be generated inside the

projector, causing deterioration in the projector quality and/or

fire.

Place of installation

For safety reasons, refrain from setting the projector at any place

subjected to high temperature and high humidity. Maintain an

operating temperature, humidity and setting as specified below:

• Operating temperature: between 41°F (5°C) and 95°F (35°C).

• Operating humidity: between 30% and 90%

• Never put any heat-producing device under the projector. The

projector may overheat.

• Do not install the projector near any equipment that produces a

strong magnetic field. Also refrain from installing near the

projector any cable carrying a large current.

• Do not install the projector in a place that is unstable or subject

to vibration; otherwise, it may fall and cause serious injury

and/or damage to the unit.

• Do not stand the projector on its side; otherwise, it may fall and

cause serious injury and/or damage to the unit.

• Do not tilt the projector more than 10° right/left or 15°

forward/backward; otherwise, it may cause a lamp explosion.

• Do not place the projector near an air conditioning unit or heater

to avoid hot air to the vents of the projector.

• Avoid installing this unit where foreign object may fall onto this

unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or discoloration on

the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire, damage to this

unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid may cause

electrical shock to the user and/or damage to this unit.

European compliance notice

This video projector complies with the requirements of the EC

Directive 89/336/EEC “EMC Directive” as amended by Directive

92/31/EEC and 93/68/EEC, and 73/23/EEC “Low Voltage

Directive” as amended by Directive 93/68/EEC.

This unit is not disconnected from the AC power source as long

as it is connected to the wall outlet, even if this unit itself is

turned off. This state is called the standby mode. In this state,

this unit is designed to consume a very small quantity of power.

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3-pin plug fitted. For details, refer to the instructions

described below.

Note

• The plug severed from the mains lead must be destroyed, as a plug

with a bared flexible cord is hazardous if engaged in a live socket

outlet.

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be

connected to the terminal in the plug which is marked by the

letter “E” or the safety earth symbol or coloured GREEN or

GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal marked with the letter “N” or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal marked with the letter “L” or coloured RED.

1 Getting started 2

Inappropriate places for installation .....................2

Accessory check ..................................................3

Inserting the batteries into the remote control......4

2 Controls and functions 5

Projector overview ...............................................5

Remote control overview .....................................6

Using the picture quality adjusting buttons .....6

3 Using the remote control 7

Operational range ................................................7

Reception angle ...................................................7

4 Installation 8

Setting up the screen ...........................................8

Mounting the projector on the table .....................8

Adjusting the projection angle..............................8

Mounting the projector on the ceiling ...................9

Screen size and projection distance ..................10

5 Connections 11

Basic home theater system connection .............11

Connecting to a video player, etc.......................12

Connecting to a DVD player or

HDTV decoder ...................................................12

HDMI or DVI connections ..................................13

D-SUB connections............................................13

Connecting to a computer..................................14

TRIGGER terminal.............................................15

Plugging in the power cable...............................15

6 Projection 16

Viewing video images ........................................16

KEYSTONE adjustment................................17

IRIS button ....................................................17

Examples of the aspect ratio.........................18

Setting the aspect ratio .................................18

Viewing computer images..................................19

AUTO / AUTO SYNC buttons .......................20

Connecting to a notebook computer.............20

7Menu 21

Menu overview...................................................21

How to set the menus ...................................22

Menu settings.....................................................23

8 Adjusting video images 27

Selecting the gamma mode (GAMMA) ............. 27

Customizing the gamma mode (GAMMA) ........ 27

Adjusting brightness (CONTRAST and

BRIGHTNESS).................................................. 27

CONTRAST ................................................. 27

BRIGHTNESS.............................................. 27

Selecting the color temperature

(COLOR TEMP.)............................................... 28

Customizing the color temperature

(COLOR TEMP.)............................................... 28

About color temperature .............................. 28

Adjusting color (SATURATION and HUE) ........ 29

SATURATION.............................................. 29

HUE ............................................................. 29

Sharpening or softening images

(SHARPNESS).................................................. 29

LPF (Progressive filter) ..................................... 29

9 MEMORY function 30

Saving memory settings.................................... 30

10 Adjusting computer images 31

Adjusting computer images............................... 31

Simple method to adjust the image

position......................................................... 31

11 Replacing the lamp 32

Interval of lamp replacement............................. 32

Replacing the lamp ........................................... 33

Maintenance...................................................... 33

12 Attaching a lens filter and cap 34

Attaching a commercially available lens filter.... 34

Attaching the lens cap....................................... 34

13 Troubleshooting 35

Troubleshooting ................................................ 35

14 Indicators 38

Normal conditions ............................................. 38

Abnormal conditions.......................................... 38

15 Specifications 39

Projector specifications ..................................... 39

Dimension drawings.......................................... 41

Table of contents

◆ Inappropriate places for installation

If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place to

install this unit by avoiding the places listed below.

1. Places where the temperature and humidity vary greatly

• Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely

low.

• This unit must be used within a temperature range of 41°F (5°C) to 95°F (35°C).

• This unit must be used within a humidity range of 30% to 90%

2. Places without adequate ventilation

• Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.

• Do not cover the ventilation slots of this unit. Covering the slots will obstruct heat dissipation.

• Install this unit on the firm surface.

• Do not cover this unit with a tablecloth, etc.

• Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.

• If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.

3. Places where it gets dusty

• If the filter is blocked with dust, the temperature of this unit may become too high.

4. Places with too much vibration or impact

• Vibration and impact can damage parts of this unit.

5. Places where this unit gets exposed to water or high humidity

• If this unit is exposed to water of high humidity, it may cause a fire or electrical shock.

6. Unstable places

• If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.

7. In close proximity to a radio or stereo

• The unit may interfere with reception if placed in close proximity to a radio or television receiver.

8. Uneven surfaces

• Slanting the projector more than 10° right and left or 15° front and rear may cause problems (such as the lamp exploding).

Warning

• To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.

*DLP

, DMD

, DarkChip2

, and DarkChip3

are registered

trademarks of the Texas Instruments corporation of America.

* HDMI, the HDMI logo and High-Definition Multimedia Interface

are trademarks or registered trademark of HDMI Licensing LLC.

Getting started1

◆ Accessory check

The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in the package.

Important

• The supplied power cables are to be used exclusively for this product. Never use them for other products.

• The power cables for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.

• The provided power cable for the U.S. is rated at 120 V. Never connect this cable to any outlet or power supply using other

voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare an appropriate power

cable separately.

■ Cables ■ Power supply parts

RGB cable for PC

(WF76940)

RS-232C cable

(WF76930)

Power cable

• Used for adjustment by service person.

■ Remote control parts ■ Others

Remote control R03 (Size-AAA) battery (two) Lens cap Owner’s manual

mini D-SUB

15-pin

mini D-SUB

15-pin

D-SUB 9-pin

8-pin

(For Europe)

(For US)

RDP-81

-V

-S

STA

ASPECT

HIDE

AUTO

SQUEEZ

S. ZO

NORMAL

COMP.

HDMI

ASPECT

INPUT

KEYSTN

SETTING

BRIGHT

SHAR

C.TEMP

CON

MEMORY

IRIS

GAM

DPX-830

Digital Cinema Projector

Projecteur Cineme Numerique

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

BRUKSANVISNING

GEBRUIKSAANWIJZING

◆ Inserting the batteries into the remote control

1. Remove the rear lid of the remote control.

2. Check the polarity markings (+, –) of the batteries, and set

them correctly, inserting their (–) side first.

• If the battery is inserted from the (+) side first, inserting the (–)

side becomes difficult because the coil spring end hits on the

battery side. If the battery is forced to insert in this way, the

outer label of the battery may get ripped and cause a short-

circuit and heating.

3. Attach the rear lid.

Important

• Use two size-AAA batteries (R03).

• Replace the two batteries with new ones when the remote

control is slow to operate.

Caution

• Using the wrong type of battery may cause an explosion.

• Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

• Dispose of used batteries according to your local regulations.

• Batteries may explode if misused. Do not recharge, disassemble, or dispose of in fire.

• Be sure to handle the battery according to the instructions.

• Load the battery with its positive (+) and negative (–) sides correctly oriented as indicated on the remote control.

• Keep batteries out of reach of children and pets.

• Remove the batteries, if the remote control is not used for a long time.

• Do not combine a new battery with an old one.

• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with

your eyes, rinse them with water and then consult your doctor.

◆ Projector overview

1. FOCUS ring

2. ZOOM ring

3. Control panel

4. Air intake vent

5. Remote control sensor (Front)

6. Air intake vent

7. Air exhaust vent

8. Adjustment foot (Front)

9. Lamp cover (see page 33)

10. Adjustment feet (Rear)

11. Foot adjustment buttons (Left/Right)

12. Air intake vent

Control panel

1. STANDBY/ON, button

2. AUTO SYNC, button

3. D-SUB/HDMI, button

4. MENU button

5. STATUS indicator

6. POWER indicator

7. KEYSTONE, ENTER button

8. VIDEO/S/COMP., button

9. button

Important

• While the menu is on the screen, the KEYSTONE button

functions as the ENTER button and the D-SUB/HDMI,

VIDEO/S/COMP., and AUTO SYNC buttons function as

the , , and buttons respectively.

Rear panel

1. AC IN

2. HDMI input terminal

3. D-SUB input terminal

4. Remote control sensor (Rear)

5. COMPONENT input terminals

6. Air exhaust vent

7. SERIAL terminal

• Used for adjustment by service person.

8. USB terminal

• Used for adjustment by service person.

9. TRIGGER terminal

• Used for the optional electric screen.

10. S-VIDEO input terminal

11. VIDEO input terminal

6 7

Top view

Side view

Bottom

view

DIGITAL CINEMA PROJECTOR DPX-830

AUTO SYNC

AC IN

HDMI

D-SUB

SERIAL

S-VIDEO

VIDEO

COMPONENT

USB

TRIGGER

23145

71011

6 8 9

Controls and functions2

◆ Remote control overview

1. IR signal transmitter

2. ON ( I ) button

3. AUTO button

4. NORMAL button

5. HDMI button

6. D-SUB button

7. Cursor buttons ( / / / )

8. MENU button

9. MEMORY buttons

10. The picture quality adjusting buttons*

* See the below for the picture quality adjusting buttons.

11. STANDBY ( ) button

12. HIDE button

13. ASPECT button

14. S. ZOOM (Smart zoom) button

15. SQUEEZ (Squeeze) button

16. VIDEO button

17. COMP. (Component) button

18. S-VIDEO button

19. ENTER button

20. KEYSTN (Keystone) button

21. IRIS button

(see page 17)

Important

•

When you press a button on the remote control, the buttons

on the remote control will light up. Wait approximately 6

seconds after releasing the button for the lights to turn off.

Using the picture quality adjusting buttons

When you press either of the picture quality adjusting buttons, the message for adjusting the picture quality appears. Adjust the picture quality

by pressing the and buttons. The picture quality adjustment can be made alternatively in the IMAGE menu (see page 23).

CONT. (CONTRAST) ..................................... Adjusts the contrast of the projected image.

GAMMA.......................................................... Selects one of the preset gamma modes.

BRIGHT (BRIGHTNESS) .............................. Adjusts the brightness of the projected image.

SHARP (SHARPNESS) .................................. Adjusts the sharpness of the projected image.

C. TEMP (COLOR TEMPERATURE) ........... Selects one of the preset color temperatures.

POWER

S-VIDEO

D-SUB

STANDBYON

ASPECT

HIDEAUTO

SQUEEZ

S. ZOOM

NORMAL

COMP. VIDEOHDMI

ASPECT

INPUT

ENTER

KEYSTN

SETTING

BRIGHT

SHARP

C.TEMP

CONT.

MEMORY

231

IRIS

GAMMA

RDP-81

◆ Operational range

Operate the remote control within a distance of 10 m from the

projector, pointing the light beam at the remote control sensor (front

or rear) of the projector.

Caution

• Keep the remote control sensor out of direct sunlight or

fluorescent lamp light.

• Keep the remote control sensor at least 2 m away from

fluorescent lamps. Otherwise, the remote control may

malfunction.

• If there is an inverter-operated fluorescent lamp near the

remote control, the remote control operation may become

unstable. On this occasion, stick a commercially available

protection sticker on one of the sensors that is closer to

the fluorescent lamp.

When operating the remote control, keep the distance from the remote

control to the projector via the screen within about 5 m. The operable

range of the remote control, however, depends on the characteristics

of the screen.

◆ Reception angle

Vertical directions

Vertical directions (ceiling mount)

30˚30˚

AC IN

RDP-81

POWER

S-VIDEO

D-SUB

STANDBYON

ASPECT

HIDEAUTO

SQUEEZ

S. ZOOM

NORMAL

COMP. VIDEOHDMI

ASPECT

INPUT

ENTER

KEYSTN

SETTING

BRIGHT

SHARP

C.TEMP

CONT.

MEMORY

231

IRIS

GAMMA

RDP-81

POWER

S-VIDEO

D-SUB

STANDBYON

ASPECT

HIDEAUTO

SQUEEZ

S. ZOOM

NORMAL

COMP. VIDEOHDMI

ASPECT

INPUT

ENTER

KEYSTN

SETTING

BRIGHT

SHARP

C.TEMP

CONT.

MEMORY

231

IRIS

GAMMA

Front panel Rear panel

Distance to sensor Angle to sensor

10 m

(approximate value)

30° left and right

(approximate value)

RDP-81

S-VIDEO

DBY

SPE

HIDEAUTO

SQU

S. Z

ORMA

COM

HDM

PECT

EYSTN

ENU

BRIG

SHAR

MOR

IRIS

AMM

20˚

10˚

20˚

10˚

Using the remote control3

◆ Setting up the screen

Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the projection angle of the projector as

shown below.

Important

• Before setting up the screen, be sure to set SCREEN ASPECT in the SETUP menu to either 16:9 or 4:3.

• Install the screen and projector so that the projector’s lens is placed at the horizontal position of the screen center.

• Do not install the screen where it is exposed to direct sunlight or lighting. Light directly reflecting on the screen makes the

projected images whitish and hard to view.

◆ Mounting the projector on the table

Determine the distance from the screen to the projector according to the size of the images to be projected (see page 10).

• Do not place this projector on a carpet or blanket because the intake vent on the bottom surface will be blocked and the inside of the

projector will overheat, causing a breakdown or fire.

• Depending on the installation conditions, warm air that is emitted from the exhaust vents may flow into the intake vent, causing the projector

to display “Over Temperature” and then stop projecting images. If this happens, clear the area around the exhaust vent.

◆ Adjusting the projection angle

This projector is provided with three feet for adjusting the projection angle on the bottom surface. Adjust the projection angle depending on

the position of the projector.

For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the adjustment

feet on the bottom of the projector.

1. Tilt the projector upwards to the appropriate angle.

2. Press the foot adjustment buttons next to the adjustment

feet (rear), and the adjustment feet will come out.

3. Release the buttons to lock the adjustment feet (rear) to

that position.

4. Rotate the adjustment feet (rear) for fine adjustment.

• If necessary, rotate the adjustment foot (front) for fine

adjustment.

After using the projector

Put the adjustment feet (rear) back into the projector by pressing the foot adjustment buttons.

When projected images are distorted to a trapezoid

When the screen and the projector are not placed perpendicularly to each other, projected images become trapezoidal. If you cannot make the

projector and the screen perpendicular to each other by mechanical adjustments, adjust keystone (see page 17).

A=B

STANDBY/ON

POWER STATUS

AUTO SYNC

ENTER

DIGITAL CINEMA PROJECTOR DPX-830

Projected distance

Height of the

projected image

Screen

Adjustment feet (rear)

4 Installation

◆ Mounting the projector on the ceiling

To view images projected by the ceiling mounted projector from the front:

When the projector is installed on the ceiling, the special ceiling mount bracket, which is commercially available, is required. Be sure to ask a

certified installation specialist for installation of the projector. Contact your dealer for details.

• Yamaha assumes no responsibilities for any damage caused by use of other manufacturer’s ceiling bracket and by inadequate installation

conditions even within the warranty period.

• When installing the projector on the ceiling, set LOCATION in the SETUP menu to FRONT/CEILING.

• Ask your installation specialist to provide a breaker. When you do not use the projector, be sure to shut down the main power by the breaker.

• When the projector is installed on the ceiling, projected images may appear darker than those projected when the projector is installed on the

floor.

• Do not install the projector where the exhaust vents are exposed to air emitted by an air conditioning. Such installation may cause a

breakdown.

• Do not install the projector near a fire alarm because it emits hot air from its exhaust vents.

Optional part

To view images projected on a translucent screen from behind:

Be sure to ask a certified installation specialist for installation of the projector. Contact your dealer for details.

• To view images projected from behind the screen, set LOCATION in the SETUP menu to REAR/TABLE.

Ceiling mount bracket PMT-L71 (low ceilings)

PMT-H75 (high ceilings)

◆ Screen size and projection distance

Refer to the following diagram to determine the screen size.

When the aspect ratio of the screen is 16:9

• The above figures are approximate and may be slightly different from the actual

measurements.

When the aspect ratio of the screen is 4:3

When the aspect ratio of the screen is 4:3, the positional relation between the projected image and the screen is as shown below. Refer to the

following table for installation.

When the aspect ratio of the image is 4:3

• The above figures are approximate and may be slightly different from the actual

measurements.

When the aspect ratio of the image is 16:9

• The above figures are approximate and may be slightly different from the actual measurements.

Screen size

Width of the projected image

Height of the

projected image

Center of the lens

Projected distance (L)

Screen size 16:9 Projected distance (L)

Diagonal Height A Width B Min. Max.

inch cm inch cm inch cm inch m inch m inch cm

40 102 20 50 35 89 56 1.4 68 1.7 6.6 17

60 152 29 75 52 133 85 2.2 103 2.6 9.9 25

80 203 39 100 70 177 114 2.9 139 3.5 13.2 33

100 254 49 125 87 221 143 3.6 174 4.4 16.5 42

150 381 74 187 131 332 216 5.5 262 6.6 24.7 63

200 508 98 249 174 443 289 7.3 349 8.9 32.9 84

250 635 123 311 218 553 362 9.2 – – 41.2 105

275 699 135 342 240 609 398 10.1 – – 45.3 115

Center of the lens

Projected distance (L)

Height of the

projected image

Width of the projected image

Screen size

Screen size 4:3 Project distance (L)

Diagonal Height A Width B Min. Max.

inch cm inch cm inch cm inch m inch m inch cm

40 102 24 61 32 81 65 1.6 79 2.0 6.8 17

60 152 36 91 48 122 98 2.5 119 3.0 10.2 26

80 203 48 122 64 163 132 3.3 159 4.0 13.6 35

100 254 60 152 80 203 165 4.2 200 5.1 17.0 43

150 381 90 229 120 305 248 6.3 300 7.6 25.5 65

200 508 120 305 160 406 332 8.4 – – 34.0 86

250 635 150 381 200 508 – – – – 42.5 108

275 699 165 419 220 559 – – – – 46.8 119

Screen size 4:3 Size of the projected image 16:9 Project distance (L)

Diagonal Height C Width B Height A Blank space (D) Min. Max.

inch cm inch cm inch cm inch cm inch cm inch m inch m inch cm

40 102 24 61 32 81 18.0 46 3.0 8 51 1.3 63 1.6 6.0 15

60 152 36 91 48 122 27.0 69 4.5 11 78 2.0 95 2.4 9.1 23

80 203 48 122 64 163 36.0 91 6.0 15 105 2.7 127 3.2 12.1 31

100 254 60 152 80 203 45.0 114 7.5 19 132 3.3 159 4.0 15.1 38

150 381 90 229 120 305 67.4 171 11.3 29 198 5.0 240 6.1 22.7 58

200 508 120 305 160 406 89.9 228 15.0 38 265 6.7 320 8.1 30.2 77

250 635 150 381 200 508 112.4 286 18.8 48 332 8.4 401 10.2 37.8 96

300 762 180 457 240 610 134.9 343 22.6 57 398 10.1 – – 45.3 115

Screen size

Height of the screen

Width of the projected image

Height of the

projected image

Center of the lens

Projected distance (L)

◆ Basic home theater system connection

Important

• Make sure that the power of the projector and that of the video equipment are turned off.

• Connection methods and terminal names may differ depending on the video equipment you are connnecting. Refer to the

instruction manual for the video equipment.

• Use of a long cable may affect the quality of the projected image.

HDMI

D-SUB

SERIAL

AC IN

VIDEO

COMPONENT

PB/CB

PR/CR

USB

TRIGGER

S-VIDEO

Video player

DVD player

Set-top box or digital tuner

Connections5

◆ Connecting to a video player, etc.

Using the VIDEO terminal

1. Connect one end (yellow) of a commercially available video

cable to the VIDEO input terminal of this projector.

2. Connect the other end (yellow) of the video cable to the

VIDEO output terminal of the video equipment.

Using the S-VIDEO terminal

1. Connect one end of the commercially available S-video

cable to the S-VIDEO input terminal of this projector.

2. Connect the other end of the S-video cable to the S-VIDEO

output terminal of the video equipment.

When a TV tuner or VCR is connected:

When you use this projector with a TV tuner or VCR connected, no image may appear or a No Signal message may appear on the screen when

you change to a channel that is not being received. In this case, set the channels of the TV tuner or VCR again. To avoid this problem, use the

TV tuner or VCR with its channel skip function enabled. (Only channels that are being received will be displayed.)

◆ Connecting to a DVD player or HDTV decoder

This projector can be connected to a video equipment such as a DVD player or HDTV decoder. Be sure to connect component video output

terminals of the video equipment to the COMPONENT input terminals of this projector.

• Images may not be projected correctly depending on the type of

DVD player you use.

• It may take some time before an image is displayed on the screen

depending on the type of the input signal.

S-VIDEO

VIDEO

COMPONENT

Y PB/CB PR/CR

Video player, etc.

To VIDEO

output terminal

Video cable

(commercially available)

To VIDEO

input terminal

S-VIDEO

VIDEO

COMPONENT

Y PB/CB PR/CR

Video player, etc.

S-VIDEO cable

(commercially available)

To S-VIDEO

output terminal

To S-VIDEO

input terminal

VIDEO

COMPONENT

PB/CB

PR/CR

S-VIDEO

Component cable

(commercially available)

DVD player or HDTV decoder

◆ HDMI or DVI connections

You can project high-quality images by connecting the HDMI input terminal of this projector to video equipment having a HDMI output

terminal or a DVI-D output terminal. In addition, this projector supports HDCP and is able to receive encrypted digital video data that are

output from DVD players.

• HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital video data for the

purpose of copy protection.

• HDMI (High-Definition Multimedia Interface) is fully backward compatible with computers, displays and consumer electronics equipments

incorporating the DVI standards.

• Depending on the video equipment you wish to connect, this projector may not display any image or not operate correctly. In such cases,

refer to the instruction manual for the connected video equipment.

When you connect this projector and DVI-Digital equipment (such as DVD player) by using the HDMI

terminal or DVI-D terminal, black color may appear light and pale depending on the type of the connected

equipment.

• This depends on the black level setting of the connected equipment. There are two kinds of methods to digitally transfer image data, in

which different black level settings are employed respectively. Therefore, the specifications of the signals output from DVD players differ

depending on the type of the digital data transfer method they use.

• Some DVD players are provided with a function to switch the methods to output digital signals. If your DVD player has such function, set it

as follows:

EXPAND or ENHANCED NORMAL

• Refer to the instruction manual of your DVD player for details.

• When your digital equipment does not have such function, adjust the BRIGHTNESS to +16 and CONTRAST to -17 in the IMAGE menu of

this projector, or adjust the black color by viewing the image.

◆ D-SUB connections

You can project high-quality images by connecting the D-SUB terminal of this projector to video equipment having a D-SUB output terminal

or BNC terminal.

• Use the supplied RGB cable when connecting the projector and the equipment.

• For video equipment having a BNC terminal, use a commercially available BNC to D-SUB cable when connecting to this projector.

SERIAL

D-SUB

USB

AC IN

TRIGGER

HDMI

Equipment having a DVI-D terminal

DVI-HDMI conversion cable

(commercially available)

To HDMI terminal

To DVI-D terminal

Equipment having a HDMI terminal

HDMI cable (commercially available)

To HDMI terminal

SERIAL

D-SUB

USB

AC IN

TRIGGER

HDMI

Equipment having a D-SUB terminal

Equipment having a BNC terminal

To D-SUB terminal

To BNC terminal

RGB cable

BNC to D-SUB cable (commercially available)

To D-SUB terminal

◆ Connecting to a computer

Important

• Make sure that the power of the projector and that of the computer are turned off.

• When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor.

• This projector may not display any image or not operate correctly depending on the computer you wish to connect. In such

cases, refer to the instruction manual of the connected computer.

For analog connections:

1. Connect one end of the supplied RGB cable to the D-SUB

terminal of this projector.

2. Connect the other end of the RGB cable to the monitor port

of the computer.

• Additional devices, such as a conversion connector and an

analog RGB output adapter, are required depending on the type

of the computer to be connected.

• This projector does not support 3-line signals (SYNC-ON-

GREEN signals).

For digital connections:

1. Connect one end of a commercially available DVI-HDMI

conversion cable to the HDMI terminal of this projector.

2. Connect the other end of the DVI-HDMI conversion cable to

the DVI terminal of the computer.

• Additional devices, such as a conversion connector and an

analog RGB output adapter, are required depending on the type

of the computer to be connected.

• When viewing images being input from a digital-connected

computer, press the HDMI button on the remote control.

• Turn on the power of the projector before that of the computer.

• Using a long cable may decrease the quality of projected

images.

• The signal input from the HDMI terminal does not output

through the D-SUB terminal.

HDMI

D-SUB

SERIAL

S-VIDEO

VIDEO

COMPONENT

Y PB/CB PR/CR

USB

TRIGGER

To D-SUB terminal

To monitor port

RGB cable

HDMI

D-SUB

SERIAL

S-VIDEO

VIDEO

COMPONENT

Y PB/CB PR/CR

USB

TRIGGER

To DVI

terminal

DVI-HDMI

conversion cable

(commercially

available)

To HDMI terminal

◆ TRIGGER terminal

The TRIGGER terminal on the rear of the projector is a terminal that outputs 12 V signal to control an externally connected equipment when

images are projected.

To use the TRIGGER terminal, set TRIGGER OUT to ON in the

SETUP menu. (The factory default is OFF.) Use the following

steps to change the setting.

With the SETUP menu:

(See page 23 for menu setting.)

1. Display the SETUP menu.

2. Select TRIGGER OUT by pressing the or button.

3. Select ON by pressing the or button.

To exit from the menu:

4. Press the MENU button several times.

• Do not use the signal output from the TRIGGER terminal as

a power for other equipment.

• Do not link the TRIGGER terminal with an audio terminal

of other equipment. This may cause a damage.

• The rated current for the TRIGGER terminal is 200 mA. If

you use a current exceeding this rating, a failure may occur.

• For information about electric screens, please contact screen

manufacturers.

◆ Plugging in the power cable

For US For Europe

1. Plug the supplied power cable into the AC IN of this projector.

2. Plug the other end of the power cable into a power outlet.

• The power cables for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.

• This projector uses the power plug of three-pin grounding type. Do not take away the grounding pin from the power plug. If the power

plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.

• The provided power cable for the U.S. is rated at 120 V. Never connect this cable to any outlet or power supply using other voltages or

frequencies than rated. If you use a power supply using other voltage than rated, prepare an appropriate power cable separately.

AC IN

HDMI

D-SUB

SERIAL

S-VIDEO

VIDEO

COMPONENT

Y PB/CB PR/CR

USB

TRIGGER

Ring (NC)

Tip (12 V)

Sleave (ground 0 V)

To TRIGGER terminal

AC IN

HDMI

D-SUB

SERIAL

USB

TRIGGER

Earthing

terminal

Power cable

AC IN

HDMI

D-SUB

SERIAL

USB

TRIGGER

Power cable

Earthing

terminal

◆ Viewing video images

Preparation:

• Always remove the lens cap before operating the projector.

• Turn on the power of the connected video equipment.

1. Confirm the POWER indicator lights up red.

• If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the STANDBY/ON

button may not work after the power cable is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the

STANDBY/ON button to turn back on the POWER indicator.

2. Press the STANDBY/ON () button on the projector or ON ( I ) button on the remote control.

• It may take about one minute for the lamp to light up.

• The lamp fails to light up on rare occasions. If this happens, wait for a few minutes and then try again.

• Do not cover the lens with the lens cap while the lamp is on.

3. Select an input source.

• Press the VIDEO/S/COMP. or D-SUB/HDMI button on the projector, or press one of the input selector buttons (VIDEO, S-VIDEO,

COMP., HDMI, or D-SUB) on the remote control to select the input you desire. Be sure to select the input source that is corresponding

to the terminal in use.

–The input source is switched to VIDEO, S-VIDEO or COMPONENT at every press of the VIDEO/S/COMP. button on the projector.

–The input source is switched between D-SUB and HDMI at every press of the D-SUB/HDMI button on the projector.

• There may be a delay before an image is displayed on the screen depending on the type of the input signal.

• Some images become easier to view when the setting of aspect ratio is changed (see page 18).

4. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their

specified sizes.

5. Adjust the position of the projector so that the projector and the screen are perpendicular to each other (see page 8).

• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle (see page 8).

6. Adjust the size of the projected image by turning the ZOOM ring.

7. Adjust the focus by turning the FOCUS ring.

Repeat steps 4 to 7, if necessary.

Important

• When a 4:3 image is continuously displayed for a long time before displaying a 16:9 image, the afterimages of the black

bars on each side may appear on the 16:9 image screen. Consult your dealer in this case.

• Do not display a still picture for a long time because the afterimages may persist on the screen.

POWER

S-VIDEO

D-SUB

STANDBYON

ASPECT

HIDEAUTO

SQUEEZ

S. ZOOM

NORMAL

COMP. VIDEOHDMI

ASPECT

INPUT

ENTER

KEYSTN

SETTING

BRIGHT

SHARP

C.TEMP

CONT.

MEMORY

231

IRIS

GAMMA

STANDBY/ON

POWER STATUS

AUTO SYNC

ENTER

DIGITAL CINEMA PROJECTOR DPX-830

RDP-81

STANDBY/ON

button

VIDEO/S/COMP.

button

FOCUS ring

ON (

I )

button

ZOOM ring

COMP. button

VIDEO button

S-VIDEO button

D-SUB/HDMI

button

HDMI button

D-SUB button

Projection6

To stop projecting:

1. Press the STANDBY/ON () button on the projector or the STANDBY ( ) button on the remote control.

• A confirmation message is displayed.

• To cancel the procedure, wait a while or press the MENU button.

2. Press the STANDBY/ON () button on the projector or the STANDBY ( ) button on the remote control again.

• The lamp goes out and the projector goes into a cooling period. In this condition, the POWER indicator turns red and the STATUS

indicator blinks green.

3. Wait about one minute for the STATUS indicator to be off and the POWER indicator to be steadily lit in red.

• During this one minute period, the intake and exhaust fans rotate to cool the lamp.

• The fan may make loud sounds during a cooling period.

Caution

• Do not unplug the power cable while the STATUS indicator is blinking. Unplugging the power cable immediately after use

may damage the lamp or reduce lamp life.

KEYSTONE adjustment

Use to correct vertical and horizontal image distortion caused by

tilting the projector.

1. Press the KEYSTONE (ENTER) button on the control area

of the projector or the KEYSTN button on the remote

control.

2. Adjust the projection angle by pressing , , ,

buttons as shown.

To exit from the menu:

3. Press the KEYSTONE (ENTER) button on the control area

of the projector or the KEYSTN button on the remote control

again.

Important

• When the keystone adjustment is applied, the correct aspect ratio may not be obtained.

• When the keystone adjustment is applied, the resolution lowers. In addition, vertical stripes appear and straight lines bend

in images with complicated patterns. To prevent such symptoms, keep the screen and the projector perpendicular to each

other as much as possible.

• When the keystone adjustment is applied, the distorted image may appear for a while.

• The projected image may be distorted depending on the setting value of the keystone adjustment and the type of the input

signals. In such cases, adjust the setting value within the range where the projected image is not distorted.

• The setting value displayed at the time of the keystone adjustment may vary depending on the type of the input signal.

IRIS button

The IRIS function adjusts the contrast optically by opening and

closing the lens aperture. Select OPEN to increase the brightness of

the image. Select CLOSE to deepen the black level of the image while

reducing the brightness.

1. Press the IRIS button on the remote control.

• The current setting appears.

2. Change the setting by pressing the IRIS button again while

the current setting is being displayed.

Press

button

Press

button

Press

button

Press

button

IRIS : CLOSE

IRIS : OPEN

SETTING

BRIGHT

SHARP

C.TEMP

CONT.

IRIS

GAMMA

IRIS button

Examples of the aspect ratio

You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Display pattern changes according to the

setting of SCREEN ASPECT in the INITIAL menu. The following table is in the case of 16:9 screen. Change the setting according to the type

of the input video signal.

*1: Available only when the input signal is 480p or 576p.

*1: When ASPECT is set to SUBTITLE ZOOM or ZOOM, display position can be changed with the or button on the remote control.

*2: OVER SCAN and BLACK MASK in the SIGNAL menu are not available in the SMART ZOOM mode.

• Bold frames are recommended modes.

• This projector is equipped with a function to change the aspect ratio. If you select an aspect ratio that is inconsistent with that of the input signal, images around the screen edges

may be hidden or deformed. When viewing original video works reflecting the authors’ intentions, you are recommended to keep their aspect ratios unchanged.

• It may be an infringement of the rights protected by the copyright law to project images compressed or enlarged by changing the aspect ratio in public areas, such as inside and

outside shops and hotels, for commercial or public viewing purposes.

Setting the aspect ratio

With the remote control:

1. ASPECT button

• Every time you press the ASPECT button, the aspect mode

changes from DEFAULT to NORMAL, SQUEEZE,

SUBTITLE ZOOM, ZOOM, SMART ZOOM, THROUGH

and back to DEFAULT. DEFAULT is automatically set to either

NORMAL or SQUEEZE depending on the input signal.

* The available aspect mode differs depending on the input signals.

2. NORMAL, SQUEEZ, S.ZOOM button

• NORMAL, SQUEEZ, S.ZOOM (SMART ZOOM) buttons on

the remote control enable you to select the aspect mode

directly.

* Depending on the input signals, these buttons may not function.

With the INITIAL menu:

(See page 22 for how to set the menus.)

1. Display the INITIAL menu.

2. Select ASPECT by pressing the or button.

3. Select your desired aspect ratio by pressing the or

button.

To exit from the menu:

4. Press the MENU button several times.

: Image area

NORMAL SQUEEZE

SUBTITLE ZOOM

ZOOM

SMART ZOOM

THROUGH

Original image size Displays the image

while keeping the

input aspect ratio.

Squeezed image is

expanded to 16:9.

Cinema scope image

is enlarged and

displayed together

with subtitles.

Vista image is

enlarged and

displayed together

with subtitles.

Image is enlarged to

16:9 while the center

aspect ratio remains

unchanged.

Input signal is

displayed in its

original size.

4:3 image (480i, 576i,

480p, 576p, and PC)

4:3 Squeezed

(480i, 576i, 480p, 576p)

4:3 LetterBox

(CinemaScope with subtitles)

(480i, 576i, 480p, 576p)

4:3 LetterBox

(Vista image)

(480i, 576i, 480p, 576p)

16:9 image (720p, 1080i)

Not available. Not available. Not available.

Sub Title

POWER STANDBYON

ASPECT

HIDEAUTO

SQUEEZ

S. ZOOM

NORMAL

ASPECT

SQUEEZ button

S.ZOOM button

NORMAL button

ASPECT button

INITIAL

DEFAULT

ASPECT

TV60

◆ Viewing computer images

Preparation:

• Always remove the lens cap before operating the projector.

• Turn on the power of the connected computer.

1. Confirm the POWER indicator lights up red.

• If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the STANDBY/ON

button may not work after the power cable is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the

STANDBY/ON button to turn back on the POWER indicator.

2. Press the STANDBY/ON () button on the projector or ON ( I ) button on the remote control.

• It may take about one minute for the lamp to light up.

• The lamp fails to light up on rare occasions. If this happens, wait for a few minutes and then try again.

• Do not cover the lens with the lens cap while the lamp is on.

3. Select an input source.

• Press the D-SUB/HDMI button on the projector or the D-SUB button on the remote control that is corresponding to the terminal in use.

–The input source is switched between D-SUB and HDMI at every press of the D-SUB/HDMI button on the projector.

• There may be a delay before an image is displayed on the screen depending on the type of the input signal.

• Images may not be projected in the correct position depending on the type of the input signal. If this happens, press the AUTO SYNC

button on the projector or the AUTO button on the remote control (see page 20).

4. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their

specified sizes.

5. Adjust the position of the projector so that the projector and the screen are perpendicular to each other (see page 8).

• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle (see page 8).

6. Adjust the size of the projected image by turning the ZOOM ring.

7. Adjust the focus by turning the FOCUS ring.

Repeat steps 4 to 7, if necessary.

Important

• When a 4:3 image is continuously displayed for a long time before displaying a 16:9 image, the afterimages of the black

bars on each side may appear on the 16:9 image screen. Consult your dealer in this case.

• Do not display a still picture for a long time because the afterimages may persist on the screen.

POWER

S-VIDEO

D-SUB

STANDBYON

ASPECT

HIDEAUTO

SQUEEZ

S. ZOOM

NORMAL

COMP. VIDEOHDMI

ASPECT

INPUT

ENTER

KEYSTN

SETTING

BRIGHT

SHARP

C.TEMP

CONT.

MEMORY

231

IRIS

GAMMA

STANDBY/ON

POWER STATUS

AUTO SYNC

ENTER

DIGITAL CINEMA PROJECTOR DPX-830

RDP-81

ON ( I ) button

AUTO button

STANDBY/ON

button

FOCUS ring

ZOOM ring

D-SUB/HDMI

button

AUTO SYNC

button

D-SUB button

To stop projecting:

1. Press the STANDBY/ON () button on the projector or the STANDBY ( ) button on the remote control.

• A confirmation message is displayed.

• To cancel the procedure, wait a while or press the MENU button.

2. Press the STANDBY/ON () button on the projector or the STANDBY ( ) button on the remote control again.

• The lamp goes out and the projector goes into a cooling period. In this condition, the POWER indicator turns red and the STATUS

indicator blinks green.

3. Wait about one minute for the STATUS indicator to be off and the POWER indicator to be steadily lit in red.

• During this one minute period, the intake and exhaust fans rotate to cool the lamp.

• The fans may make loud sound during the cooling period.

Caution

• Do not unplug the power cable while the STATUS indicator is blinking. Unplugging the power cable immediately after use

could damage the lamp or reduce lamp life.

AUTO / AUTO SYNC buttons

When the image being input from the computer is displaced, carry out the following procedure:

1. Disable the screen saver if it has been enabled.

2. Display a bright image (such as a full-screen display of the Recycle Bin window).

3. Press the AUTO button on the remote control or the AUTO SYNC button on the projector.

The projector automatically makes optimum positional settings for the input signal.

• If the image is not projected in the correct position even after you press the AUTO or AUTO SYNC button several times, change the

settings in the SIGNAL menu to put the image in the correct position (see page 31).

• When you carry out this procedure with a dark image, the image may be displaced.

Connecting to a notebook computer

When the projector is connected to a notebook computer, images may not be projected in some cases. If this happens, set the computer so that

it can output signals externally. The setting procedure varies depending on the type of the computer. Refer to the instruction manual of your

computer.

◆ Menu overview

Menus are not displayed when no signal is received by the projector.

After selecting the items marked with , press the ENTER button.

*1: Not available with certain signals.

*2: The defaul value and the setting range differ depending on the input signal.

*3: See next page for availability and unavailability.

IMAGE GAMMA DEFAULT

DYNAMIC

CINEMA

STANDARD

CUSTOM1 , CUSTOM2

± 30

CONTRAST

NATIVE

BRIGHTNESS

HIGH

± 10

± 5

ON, OFF

MID

COLOR TEMP.

LOW

CUSTOM

GAMMA - CUSTOM1

REFERENCE

GAMMA - CUSTOM2

DYNAMIC, STANDARD, CINEMA

± 5

SET UP

BLUE, BLACK

SCREEN ASPECT

16:9, 4:3

VERTICAL LOCATION

± 26

SCART INPUT

LAMP MODE

INITIAL ASPECT DEFAULT, NORMAL, SQUEEZE, SUBTITLE ZOOM, ZOOM, SMART ZOOM, THROUGH

DEFAULT, 0%, 3.75%, 7.5%

HIDE SCREEN COLOR

AUTO POWER ON

OFF, 5, 10, 15, 30, 60 minAUTO POWER OFF

SPLASH SCREEN

AUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60COLOR SYSTEM

PROGRESSIVE MODE

AUTO, VIDEO

SET UP LEVEL

LANGUAGE

RESET ALL

SIGNAL

HORIZ.POSITION

D-SUB INPUT

0 - 999

VERT.POSITION 0 - 999

PHASE 0 - 31

TRACKING

SYNC NOISE MASK

0 - 9999

SYNC NOISE MASK

LEFT

RIGHT

A/D SETTING

BEGIN

END

CLAMP POSITION

CLAMT WIDTH

VERT. SYNC

LPF

UPPER LEFT, UPPER RIGHT, LOWER LEFT, LOWER RIGHTMENU POSITION

SATURATION

BrilliantColor

SHARPNESS

HUE

BLACK MASK

EXECUTE

BLACK MASK TOP

BOTTOM

OVER SCAN

100 - 90%

AUTO, RGB, COMPONENT

STANDARD, CINEMA

LOCATION

FRONT/TABLE, REAR/TABLE, FRONT/CEILING, REAR/CEILING

TRIGGER OUT

CROSS HATCH , WHITE , BLACK

TEST PATTERN

A/D SETTING

EXECUTE

OFF

EXECUTE

, ENGLISH, ESPANÕL, DEUTSCH, FRANÇAIS, ITALIANO,

COLOR TEMP. - CUSTOM

CONTRAST R

CONTRAST G

CONTRAST B

BRIGHTNESS R

BRIGHTNESS G

BRIGHTNESS B

± 30

0 - 95

0 - 99

0 - 63

1 - 63

AUTO, OFF

ON, OFF

0 - 38

ON, OFF

*1*3

Menu7

How to set the menus

Following describe how to set AUTO POWER OFF time as an

example.

1. Press the MENU button.

• If no signal is input, the menu does not appear.

2. Press the or button to select a menu to use.

• SETUP menu is selected in this example.

3. Press the ENTER button (or button).

4. Press the or button to select an item to adjust.

5. Set the selected item by pressing the or button.

To exit from the menu:

6. Press the MENU button several times.

Important

• If the MENU button does not function, unplug the

power cable from the wall outlet. Wait about 10

minutes, plug the power cable in, and try again.

SATURATION Unavailable when the input source is HDMI or D-SUB source is an RGB signal.

HUE Available only when the VIDEO or S-VIDEO source is NTSC or 4.43NTSC signal.

SHARPNESS Unavailable when the D-SUB or HDMI source is a computer signal.

PROGRESSIVE MODE Available only when the input signal is TV50, TV60, 480i or 576i.

COLOR SYSTEM Available only when the input source is VIDEO or S-VIDEO.

SET UP LEVEL Unavailable when the input source is HDMI, and also when the D-SUB source is a computer signal.

SCART INPUT Available only when the input source is D-SUB.

HORIZ. POSITION Unavailable when the input source is HDMI.

VERT. POSITION Unavailable when the input source is HDMI.

PHASE Available when the input source is COMPONENT and D-SUB, except RGBCs (576i) signal.

TRACKING Available only when the D-SUB source is a computer signal.

OVER SCAN Unavailable when the VIDEO or S-VIDEO source is NTSC, 4.43NTSC, PAL-M, PAL-60 signal.

D-SUB INPUT Available only when the input source is D-SUB except RGBCs (576i) signal.

SYNC NOISE MASK Available when the input source is COMPONENT 720p, 1080i signal and D-SUB 720p, 1080i computer

signal.

CLAMP POSITION Available when the input source is COMPONENT and D-SUB, except RGBCs (576i) signal.

CLAMP WIDTH Available when the input source is COMPONENT and D-SUB, except RGBCs (576i) signal.

LPF Available only when the COMPONENT or D-SUB source is a 480i/p, 576i/p signal, except RGBCs (576i)

signal.

IMAGE

TV60

SETUP

TV60

SETUP

16:9

CINEMA

OFF

SCREEN ASPECT

VERTICAL

LOCATION

LAMP MODE

AUTO POWER

OFF

TV60

OFF

AUTO POWER ON

AUTO POWER

OFF

SPLASH

SCREEN

OFF

30 min

AUTO POWER

OFF

SPLASH

SCREEN

◆ Menu settings

The following items in the menus enable you to customize this projector.

1. IMAGE menu

• DEFAULT depends on the two signal types below:

1. Video signals (TV50, TV60, 480i/p, 576i/p, 720p50/60, 1080i50/60)

2. Computer signals (VGA, XGA, etc.)

See page 40 for a complete listing for the signal specifications.

• Memory function saves up to 3 patterns of the IMAGE menu for each input terminal (see page 30).

• BrilliantColor

uses BrilliantColor

technology of Texas Instruments of USA.

ITEM SETTING FUNCTION

GAMMA DEFAULT The appropriate gamma mode is automatically selected depending on the input signal. Select

DEFAULT for normal use.

DYNAMIC Select to secure the contrast even when the room lighting is increased to some extent.

STANDARD Select to gain the halftone to make the skin color more vibrant even in a dark scene. This

mode is suitable for TV viewing.

CINEMA Select when watching movies in dim lighting as in a theater.

CUSTOM 1 ,

CUSTOM 2

Use to customize the gamma mode (see page 27).

CONTRAST ± 30 Use to adjust the contrast of the projected image (see page 27).

BRIGHTNESS ± 30 Use to adjust the brightness of the projected image (see page 27).

COLOR TEMP. NATIVE Select this option when projecting the image without adjusting the color temperature.

H Select for a high color temperature (see page 28).

M Select for a balanced color temperature (see page 28)

L Select for a low color temperature (see page 28)

CUSTOM

Use to customize the color temperature (see page 28)

SATURATION ± 10 Use to adjust the color richness of the projected image (see page 29).

HUE ± 10 Use to adjust the color tint of the projected image (see page 29).

SHARPNESS ± 5 Use to adjust the sharpness of the projected image (see page 29).

BrilliantColor

ON, OFF Select ON to increase the brightness of the projected image by boosting the midtone color

levels while ensuring more vibrant colors. Select OFF when viewing the scene (i.e. a live

indoor concert) that is already high in contrast. In such a case, the color and contrast appears

more natural with BrilliantColor deactivated.

IMAGE

DEFAULT

MID

GAMMA

CONTRAST

BRIGHTNESS

COLOR TEMP.

SATURATION

HUE

SHARPNESS

OFF

BrilliantColor

TV60

2. SETUP menu

• Do not change the setting of the LAMP MODE frequently. This could damage the lamp.

• To exit from the TEST PATTERN, press any buttons on the remote control.

SETUP

16:9

CINEMA

OFF

BLUE

SCREEN ASPECT

VERTICAL

LOCATION

LAMP MODE

AUTO POWER

OFF

SPLASH

SCREEN

HIDE SCREEN

COLOR

FRONT/TABLE

OFF

CROSS HATCH

LOCATION

TRIGGER OUT

TEST PATTERN

TV60

ITEM SETTING FUNCTION

SCREEN ASPECT 16:9, 4:3 Use to select the screen size.

VERTICAL

LOCATION

± 26 Use to adjust the position (height) of the projected image.

LAMP MODE STANDARD Select when using the projector in a bright environment.

CINEMA Select to moderate the intensity of the lamp. The operating sound is reduced and the lamp

lifetime becomes longer.

AUTO POWER ON ON, OFF When ON is selected, the lamp is automatically lit when the power cord is plugged in the

wall outlet. Select ON when using the projector mounted on the ceiling.

AUTO POWER

OFF

OFF, 5 – 60min Use to set the time elapsed before the projector enters the stand-by mode when there is no

signal input from the source.

SPLASH

SCREEN

ON, OFF Select ON to display the splash screen when the power is turned on

HIDE SCREEN

COLOR

BLUE, BLACK Use to select the backbround when there is no signal inputted from the selected source.

LOCATION FRONT/TABLE Select when viewing images from the front with the projector installed on the floor.

REAR/TABLE Select when viewing images projected from behind of the screen with the projector installed

on the floor.

FRONT/CEILING Select when viewing images from the front with the projector installed on the ceiling.

REAR/CEILING Select when viewing images projected from behind of the screen with the projector installed

on the ceiling.

TRIGGER OUT ON, OFF Selec ON when there is a signal received at the TRIGGER OUT terminal

TEST PATTERN

CROSS HATCH

Select to display the test cross hatched pattern.

WHITE

Select to display the maximum brightness image.

BLACK

Select to display the minimum brightness image.

3. INITIAL menu

• DEFAULT depends on the two signal types below:

1. Video signals (TV50, TV60, 480i/p, 576i/p, 720p50/60, 1080i50/60)

2. Computer signals (VGA, XGA, etc.)

See page 40 for a complete listing for the signal specifications.

ITEM SETTING FUNCTION

ASPECT DEFAULT The appropriate aspect ratio is automatically selected depending on the input signal. Select

DEFAULT for normal use.

NORMAL Select to project images with an aspect ratio of 4:3.

SQUEEZE Select to project images with an aspect ratio of 16:9.

SUBTITLE ZOOM Select to project subtitled letter box format software.

ZOOM Select to enlarge and project images of CinemaScope size or Vista size.

SMART ZOOM Select to stretch the left and right edges of a 4:3 image without altering the image center to

project a 16:9 image that fills the screen.

THROUGH Select to project images in their original size as input.

MENU POSITION 4 positions Use to change the position of the menu being displayed on the screen.

PROGRESSIVE

MODE

AUTO Detects the video and film contents and convert into opitmized progressive frames

automatically.

VIDEO Force to convert using motion-adaptive I/P conversion for video contents only.

COLOR SYSTEM 8 options

When AUTO is selected, the appropriate video format is automatically selected depending on

the input signal. If the image is not displayed correctly, select the desired video format manually.

SET UP LEVEL DEFAULT, 0%,

3.75%, 7.5%

Select the black level of the projected image. SET UP LEVEL is automatically set to 7.5%

when you select any language except (Japanese) in the LANGUAGE menu. Select

DEFAULT for normal use.

SCART INPUT ON, OFF Select ON when connecting the projector to the equipment having a SCART terminal that can

output RGB signal. SCART terminal is used mainly in Europe. Select OFF for normal use.

LANGUAGE 10 languages Use to select the language used in the menu.

RESET ALL

EXECUTE

Use to reset the settings of the menu (excluding LANGUAGE) to its factory presets. It may

take few seconds that the projector is reset to its factory presets.

INITIAL

DEFAULT

UPPER LEFT

AUTO

DEFAULT

ASPECT

MENU POSITION

PROGRESSIVE

MODE

COLOR SYSTEM

SET UP LEVEL

SCART INPUT

TV60

OFF

ENGLISH

LANGUAGE

RESET ALL

EXECUTE

4. SIGNAL menu

* The default value and the setting range differ depending on the input signals.

• Horizontal strips may appear on the enlarged projected image.

• When changing a horizontal or vertical position to a large extent, noise may appear.

• When you select COMPONENT as an input source, the setting of D-SUB INPUT will be changed to COMPONENT automatically.

• OVER SCAN and BLACK MASK are not available when the aspect ratio is set to SMART ZOOM (see page 18).

• OVER SCAN is not available when the aspect ratio is set to THROUGH (see page 18).

• If you increase the OVER SCAN setting when the projector is receiving the video signals, noise may appear on the screen. In such case,

decrease the OVER SCAN setting.

SIGNAL

0 - 999

0 - 31

0 - 999

100 - 90%

AUTO

HORIZ. POSITION

VERT. POSITON

PHASE

TRACKING

OVER SCAN

D-SUB INPUT

SYNC NOISE

MASK

EXECUTE

A/D SETTING

TV60

EXECUTE

BLACK MASK

ITEM SETTING FUNCTION

HORIZ. POSITION

0 – 999*

Use to adjust the horizontal position of the projected image.

VERT. POSITION

0 – 999*

Use to adjust the vertical position of the projected image. The adjustable range varies

depending on the type of the input signal. In some cases, the image may stay in the same

position even when the setting value is changed.

PHASE

0 – 31*

Use to eliminate flickering or blur, if it appears while viewing the projected image.

TRACKING

0 – 9999*

Use to eliminate vertical wide stripes, if it appears, while viewing the projected image.

OVER SCAN

100% – 90%*

Use to adjust the over scan ratio for the video signals.

D-SUB INPUT AUTO When the projector detects the three-wire system (YC

/ YP

) or five-wire system

(RGBHV), it automatically selects either COMPONENT or RGB accordingly.

RGB Select this option when connecting the projector to high definition video equipment having

R, G, and B output terminals.

COMPONENT Select this option when connecting the projector to a DVD player or other equipments having

Y, C

, and C

(or Y, P

, and P

) component video output terminals.

BLACK MASK

EXECUTE

Use to adjust the image when the noise appears on the projected image.

TOP Adjust the image when the noise appears on the top part of the image.

BOTTOM Adjust the image when the noise appears on the bottom part of the image.

LEFT Adjust the image when the noise appears on the left part of the image.

RIGHT Adjust the image when the noise appears on the rigtht part of the image.

SYNC NOISE MASK

ON , OFF

Use to adjust the image when flagging occurs near the top of the screen.

BEGIN Use to adjust the start of the sync noise mask position.

END Use to adjust the end of the sync noise mask position.

A/D SETTING

EXECUTE

Use to adjust the Analog Digital conversion parameters.

CLAMP POSITION Use to correct solid white or solid black in the projected image.

CLAMP WIDTH Use to correct solid black in the projected image.

VERT. SYNC Use to adjust the image when its motion does not run smoothly.

LPF Use to reduce the streak noise appeared on the image. (see page 29).

◆ Selecting the gamma mode (GAMMA)

You can select a preset gamma mode by using the menu (see page 23).

1. Display the IMAGE menu.

2. Select GAMMA by pressing the or button.

3. Select your desired gamma mode by pressing the or button.

• Select DEFAULT for normal use.

To exit from the menu:

4. Press the MENU button several times.

◆ Customizing the gamma mode (GAMMA)

To customize and store the gamma mode, carry out the following procedure.

1. Select GAMMA in the IMAGE menu.

2. Press the or button to selcet CUSTOM 1 or

CUSTOM 2 .

3. Press the ENTER button.

• The GAMMA-CUSTOM1 menu appears as shown.

4. Press the or button to select REFERENCE.

5. Select the desired gamma mode from DYNAMIC,

STANDARD, or CINEMA.

6. Press the or button to select an item from H (High),

M (Middle), or L (Low), and then adjust the level of each

item by pressing the or button.

7. Repeat step 5 to 6 for optimum adjustiment result.

To exit from the menu:

8. Press the MENU button several times.

To activate the customized gammma mode:

1. Press GAMMA button on the remote control.

• The current setting appears.

2. Press the or button to select GAMMA - CUSTOM1

or GAMMA - CUSTOM2.

To exit from the menu:

3. Press the GAMMA button on the remote control.

◆ Adjusting brightness (CONTRAST and BRIGHTNESS)

You can make adjustments for the brightness of the projected image using the menu (see page 23).

1. Display the IMAGE menu.

2. Select CONTRAST or BRIGHTNESS by pressing the or button.

3. Adjust the selected item by pressing the or button.

To exit from the menu:

4. Press the MENU button several times.

CONTRAST

Select to adjust the bright areas (white level) in the image. Increase this figure by pressing the button to increase the contrast clarity of the

image or decrease this figure by pressing the button to reduce the contrast of the image.

BRIGHTNESS

Select to adjust the overall brightness of the image. Increase this figure by pressing the button to render a brighter image or decrease this

figure by pressing the button to render a darker image.

GAMMA - CUSTOM1

CINEMA

REFERENCE

GAMMA : DEFAULT

GAMMA : CUSTOM1

8 Adjusting video images

◆ Selecting the color temperature (COLOR TEMP.)

You can select a preset color temperature (white tone) using the menu (see page 23).

1. Display the IMAGE menu.

2. Select COLOR TEMP. by pressing the or button.

3. Select your desired color temperature by pressing the or button.

To exit from the menu:

4. Press the MENU button several times.

◆ Customizing the color temperature (COLOR TEMP.)

To customize and store the color temperature, carry out the following procedure.

1. Select COLOR TEMP. in the IMAGE menu.

2. Press the or button to select CUSTOM .

3. Press the ENTER button.

• The COLOR TEMP. - CUSTOM menu appears as shown.

4. Press the or button to select an item from

CONTRAST R (red), CONTRAST G (green),

CONTRAST B (blue), BRIGHTNESS R (red),

BRIGHTNESS G (green), and BRIGHTNESS B (blue).

5. Press the or button to adjust the value of each

item.

6. Repeat step 4 and 5 for optimum adjustment results.

To exit from the menu:

7. Press the MENU button several times.

To activate the stored color temperature settings:

1. Press C.TEMP on the remote control.

• The current setting appears.

2. Press the or button to select CUSTOM .

To exit from the menu:

3. Press the C.TEMP button on the remote control.

About color temperature

There are different kinds of white color. Color temperature is a way to show the differences in white. With the higher color temperature, white

area of the image appears reddish, with the lower color temperature, white area of the image appears bluish. This projector adjusts the color

temperature by changing the values of the blue and red contrasts.

To raise the color temperature:

Increase the CONTRAST B (blue) and decrease the CONTRAST R (red).

To reduce the color temperature:

Decrease the CONTRAST B (blue) and increase the CONTRAST R (red).

Important

• If you set all of CONTRAST R, G and B to negative value, the original brightness of the image can not be obtained even

when you maxmize CONTRAST in the IMAGE menu.

COLOR TEMP. - CUSTOM

CONTRAST R

CLAMP WIDTH

BRIGHTNESS B

CONTRAST G

CONTRAST B

BRIGHTNESS R

BRIGHTNESS G

COLOR TEMP. : NATIVE

COLOR TEMP. : CUSTOM

◆ Adjusting color (SATURATION and HUE)

You can adjust the color of the projected image using the menu (see page 23).

1. Display the IMAGE menu.

2. Select SATURATION or HUE by pressing the or button.

3. Adjust the selected item by pressing the or button.

To exit from the menu:

4. Press the MENU button several times.

SATURATION

Use to adjust the richness of the color in the projected image. Increase this figure by pressing the button to render a richer color or decrease

this figure by pressing the button to render a lighter color.

• Unavailable when the input source is HDMI or D-SUB source is an RGB signal.

HUE

Use to adjust the tint of the projected image. Increase this figure by pressing the button to render a greenish image or decrease this figure by

pressing the button to render a reddish image.

• Available only when the VIDEO or S-VIDEO source is NTSC or 4.43NTSC signal.

◆ Sharpening or softening images (SHARPNESS)

You can adjust the sharpness of the projected image using the menu (see page 23).

1. Display the IMAGE menu.

2. Select SHARPNESS by pressing the or button.

3. Adjust the selected item by pressing the or button.

• Increase this figure by pressing the button to render a sharper image, or reduce it by pressing the button to give a softer image with less

image noise.

To exit from the menu:

4. Press the MENU button several times.

◆ LPF (Progressive filter)

You can select whether or not to enable the LPF. This item is normally set to OFF.

Vertical or horizontal streak noise may appear on the projected image depending on the type of the DVD player you use. In such cases, you can

reduce such streak noise by enabling the LPF. However, projected images become softened slightly.

1. Select A/D SETTING in the SIGNAL menu.

2. Press the or button to select EXECUTE .

3. Press the ENTER button.

4. Press the or button to select LPF.

5. Press the or button to choose ON or OFF.

To exit from the menu:

6. Press the MENU button several times.

EXECUTE

OFF

CLAMP

POSITION

CLAMP WIDTH

LPF

CLAMP WIDTH

OFF

VERT. SYNC

◆ Saving memory settings

The memory function saves up to 3 patterns of the image quality settings for each input source. Following is the list of items that can be saved.

You can not change the customized setting in GAMMA and COLOR TEMP. for each memory number.

1. Press one of the MEMORY buttons on the remote controll where you wish to store the settings.

2. Adjust the each item listed above in the IMAGE menu.

• The settings are automatically stored.

• You can also use the picture quality adjusting bottons on the remote control (see page 6).

To exit from the menu:

3. Press the MENU button several times.

To activate the stored memory settings:

1. Press one of the MEMORY buttons on the remote control.

• The image quality settings that are stored in the selected memory is activated.

To exit from the menu:

2. Press the same MEMORY button that you selected in step 1.

Important

• When the input source is changed, the projector automatically reverts to the previousely selected memory setting.

• When RESET ALL in the INITIAL menu is selected, all the settings that are stored in the memory will be cleared (see page

25).

• GAMMA* • SATURATION

• CONTRAST • HUE

• BRIGHTNESS • SHARPNESS

• COLOR TEMP.* • BrilliantColor

KEYSTN

SETTING

BRIGHT

SHARP

C.TEMP

CONT.

MEMORY

231

IRIS

GAMMA

MEMORY buttons

Picture quality adjusting

buttons

MEMORY 1

9 MEMORY function

This projector automatically and properly projects video signals supplied from the computer. However, some video signals may not be

projected depending on the type of the computer. In such cases, press the AUTO SYNC button on the projector or the AUTO button on the

remote control (see page 20). When the signal is still not projected properly, adjust the projected image using the SIGNAL menu.

◆ Adjusting computer images

Carry out the following procedures according to the symptoms.

(See page 22 for how to set the menus)

Wide strips appear.................................................Adjust TRACKING in the SIGNAL menu.

The projected image flickers or the projected image is blurred

..............................................................................Adjust PHASE in the SIGNAL menu.

The projected image is displaced horizontally .....Adjust HORIZ. POSITION in the SIGNAL menu. Every time the button is

pressed, the image moves to the right. Every time the button is pressed, the

image moves to the left.

The projected image is displaced vertically..........Adjust VERT. POSITION in the SIGNAL menu. Every time the button is

pressed, the image moves down. Every time the button is pressed, the

image moves up.

The top part of the image flags .............................Change the setting of SYNC NOISE MASK in the SIGNAL menu. Select

ON , press the ENTER button, and adjust BEGIN or END to minimizethe

flagging.

Wide strips appear.................................................Adjust CLAMP POSITION or CLAMP WIDTH in the A/D SETTING.

The motion does not run smoothly .......................Adjust VERT. SYNC. in the A/D SETTING. Select AUTO for normal use.

Noise appears on the right or left half of the image

..............................................................................Adjust LEFT or RIGHT in the BLACK MASK.

Noise appears on the top or bottom part of the image

..............................................................................Adjust TOP or BOTTOM in the BLACK MASK.

1. Display the SIGNAL menu.

2. Press the or button to select an item to adjust.

3. Adjust the selected item by pressing the or button.

To exit from the menu:

4. Press the MENU button several times.

Simple method to adjust the image position

To adjust the horizontal position:

1. Align the left edge of the image with the left side of the screen by adjusting HORIZ. POSITION. Then, align the right edge of

the image with the right side of the screen by adjusting TRACKING.

2. Repeat the previous step to complete the adjustment of the horizontal position.

To adjust the vertical position:

3. Align the upper edge of the image with the upper side of the screen by adjusting VERT. POSITION.

Adjusting computer images

This projector is equipped with a lamp to project images. This lamp is a consumable, so it may burn out or its brightness may decrease during

use. If this happens, replace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new, commercially available lamp

that is exclusive to this projector. Contact your dealer for purchase of the lamp.

Warning

• This product contains a high intensity lamp that contains a small amount of mercury. Disposal of this material may be

regulated due to environmental considerations. For disposal information in the United States, refer to the Electronic

Industries Alliance web site: www.eiae.org

• Be careful not to drop the lamp screws into the projector. Do not put a metal piece or flammable object into the projector.

Using the projector with any foreign object present inside may result in electric shock or fire. If you can’t remove the foreign

object from the inside, contact your dealer for removal.

• Be sure to install the lamp securely. If the lamp is not installed properly, it will not illuminate. Improper installation may also

result in fire.

• Do not shake the removed lamp or lift it above your face. You may injure your eye by flying or falling glass fragments.

• Do not replace the lamp immediately after use because the lamp cover is very hot. You may get burned. Turn off the power

using the STANDBY/ON button. After the lamp goes out, wait about two minutes until the intake and exhaust fans for cooling

the lamp stop rotating. Then unplug the power cable, and wait at least one hour to allow the lamp to cool down enough to

the touch.

◆ Interval of lamp replacement

The recommended interval of lamp replacement is about 3000 hours

of consecutive use when the LAMP MODE in the SETUP menu is set to

CINEMA

. Such interval differs depending on the operating environment and may be shorter than 3000 hours

. Decrease in luminescence and/

or color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds 2250 hours, the indicator will blink

alternately between green and red (while the lamp is lit; when the lamp is not lit, the indicator will be lit red only) and the lamp replacement

message will appear on the screen for one minute everytime the lamp is turned on. When the lamp has been used for about 2850 hours, the

replacement message (LAMP EXCHANGE) will appear on the screen for one minute every 15 hours thereafter.

When the lamp operation time exceeds 3000 hours

, the projector automatically shuts off and can not be

used until the lamp is replaced and the lamp operation time is reset.

*When the LAMP MODE is set to STANDARD, this duration will be decreased to 2000 hours.

Caution

• Be sure to use the replacement lamp cartridge PJL-725. Other lamp cartridges are not suitable for use in this projector.

• Do not remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a

breakdown.

• This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may explode or fail

to illuminate permanently because of an impact, scratch, or deterioration through use. The period of time until explosion or

permanent failure to illuminate varies considerably from lamp to lamp, depending on operation conditions. Therefore, the

lamp may explode soon after the start of use.

• The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the lamp replacement

warning appears, replace it with a new one immediately, even if the lamp is still lighting normally.

• When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and the gas

charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains mercury. Be careful not

to breathe it and avoid it from entering your eye or mouth. If you should breathe it or if it should enter your eye or mouth, see

a doctor immediately.

• In the event that the high-pressure mercury lamp has exploded, glass fragments may have been scattered inside the

projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace the lamp

by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments.

• Do not replace the lamp with the projector installed on the ceiling. Glass fragments may fall from the projector, entering your

eye or mouth and causing injury.

• When placing the projector upside down to replace the lamp or conduct maintenance, be sure that the projector is securely

placed before working with it.

◆ Replacement lamp cartridge (Option)

Spare lamp PJL-725

Replacing the lamp

◆ Replacing the lamp

Warning

• Do not replace the lamp immediately after using the

projector because the lamp would be extremely hot

and it may cause burns.

1. Carefully turn the projector upside-down (a).

2. Loosen the screw (b) using a Phillips screwdriver (+), and

remove the lamp cover (c).

3. Loosen the lamp screws (d) using a Phillips screwdriver (+).

4. Pull up the handle (e).

5. Pull out the lamp box by the handle while holding the

projector (f).

• Pull the lamp box out of the projector slowly. If it is pulled out

quickly, the lamp may break scattering glass fragments.

• Do not spill liquid on the removed lamp box or place it near any

flammable object or where children can reach to prevent fire

and injury.

6. Load a new lamp box securely into the projector in the right

orientation (g).

7. Put the handle back to the original position (h).

• Make sure that the handle is locked.

8. Tighten the screws (d) using a Phillips screwdriver (+).

9. Tighten the screw (b) using a Phillips screwdriver (+) to

secure the lamp cover.

Reset of the lamp operation time

Plug in the power cable and reset the lamp operation time by pressing and holding the , , and STANDBY/ON buttons on the control panel

at the same time.

Important

• Unless these three buttons are pressed at the same time, the lamp operation time is not reset.

• Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully.

• The projector does not turn on if the lamp cover is not attached securely.

• Be sure to reset the lamp operation time whenever you replace the lamp, otherwise the lamp may not be turned on.

• Do not reset the lamp operation time unless you replace the lamp.

• This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due

to environmental considerations.

◆ Maintenance

Caution

• Be sure to turn off the lamp and unplug the power cable from the wall outlet before you perform any maintenance on the

projector.

Cleaning the projector and the ventilation grilles

Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened with

diluted mild detergent, and then wipe them with a dry cloth.

To protect the surface of the projector from fading or deteriorating:

• Do not spray insecticide on or inside the projector.

• Do not use benzine or thinner to clean it.

• Do not let rubber or plastic materials contact with projector.

Cleaning the lens

Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only

recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fingers.

(h)

(g)

(e)

(f)

(d)

(c)

(b)

(a)

◆ Attaching a commercially available lens filter

1. Carefully turn the projector upside-down.

2. Loosen the screw (a) using a Phillips screwdriver (+), and

remove the stopper (b).

3. Place a lens filter (c).

4. Rotate the stopper 180° and reinsert it into its original

location (d).

5. Tighten up the screw (e) using a Phillips screwdriver (+).

Important

• Be sure to use a 67 mm lens filter for this projector.

• Not all 67 mm lens filters are compatible with this

projector.

◆ Attaching the lens cap

Attach the supplied lens cap when not using the projector to prevent the lens from becoming dirty or damaged. Insert the lens cap until it is

securely placed. (It should make a clicking sound.)

Important

• Do not force the lens cap onto the projector.

• Make sure that the YAMAHA name on the lens cap is aligned parallel to the top and bottom edges of the projector.

• The lens cap can be placed over the lens filter if a lens filter has been installed.

(a)

(b)

(c)

Closed position

(no lens filter)

(d)

(e)

To hold a lens filter

Attaching a lens filter and cap

◆ Troubleshooting

Refer to the chart below when this projector does not function properly. If the problem you are experiencing is not listed below or if the

instructions do not help, stop using the projector and contact your dealer.

No image appears on the screen.

Problem Solution

Power can not be turned on. • Check whether the indicators are on or off and how they are lightning.

No image appears on the

screen.

• Check that the lens cap is removed.

• It may take about one minute for the lamp to light up.

• The lamp fails to light up on rare occasions. In such cases, wait for a few minutes and then try again.

• If the projector was turned off before the lamp cooled down completely, the fans may start rotating and the

STANDBY/ON button may not function when you plug the power cable into the wall outlet next time.

Wait for the fans to stop and press the STANDBY/ON button to turn on the lamp again.

• Check that the intake vent is clean.

• Check that the lamp cover is closed (see page 33).

• Check that the cables connected to the external equipments are not broken.

• If an extension cable is being used, replace it with the supplied cable for troubleshooting purposes. If

images are now displayed correctly, add an RGB signal amplifier to the extension cable.

Projected images suddenly

disappear.

• The air intake or exhaust vent may be blocked. In such cases, the STATUS indicator blinks orange. After

removing the objects blocking the intake vent and/or exhaust vents and then carry out the following

procedure:

1. Wait for the air intake or exhaust fan to stop (or wait for the STATUS indicator to go out.)

2. Unplug the power cable from the wall outlet.

3. Wait about 10 minutes.

4. Plug the power cable into the wall outlet.

5. Press the STANDBY/ON button.

6. When the STATUS indicator is steady red, it is indicating that the lamp should be replaced.

Replace the lamp with a new, commercially available lamp.

POWER

Off

Steady red

Blinking

red/green

STATUS

Off

Blinking

orange

Blinking

green

Steady red

Off

Steady

Blinking

Solution

• Connect the power cable to the projector.

• Plug the power cable into a wall outlet.

• If any objects are blocking the air intake or exhaust vent, remove them and carry out the

following.

1. Unplug the power cable from the wall outlet.

2. Make sure that the projector has cooled off.

3. Plug the power cable into the wall outlet.

4. Press the STANDBY/ON button.

• If any objects are blocking the air intake or exhaust vent, remove them.

• Don't expose the air exhaust vents to hot air emitted from a heating appliance.

• Clean the ventilation grilles.

• Relocate the projector to a cooler place.

• After the STATUS indicator stops blinking, press the

STANDBY/ON button.

• If you unplug the power cable while the fan is rotating, the lamp may not turn on about

one minute when you plug the power cable next time.

• The lamp can't turn on again for one minute after it goes out.

• Press the

STANDBY/ON button several times.

• Replace the lamp. (The lamp is at the end of its life.)

• Attach the lamp cover on the bottom.

• Unplug the power cable from the wall outlet and contact your dealer.

Troubleshooting

Images are not displayed correctly.

“NO SIGNAL” is displayed. • Turn on the power of the connected equipment, or check whether there is something wrong with the

connected equipment.

• Check whether the external equipment outputs signals. (Check this especially when the external equipment

is a notebook computer.)

• Check that the cable connected to the external equipment is not defective.

• Check that the projector is connected to the external equipment using the correct terminals.

• Check that the connected equipment is correctly selected as the input source.

• If an extension cord is being used, replace it with the supplied cable and check whether images are

projected correctly. If images are now projected correctly, add an RGB signal amplifier to the extension

cord.

Problem Solution

Projected images are shaking.

Projected images are

displaced.

• Check that the signal being output by the external equipment is not intermittent.

• Connect the cable plug firmly.

• Press the AUTO button on the remote control or AUTO SYNC button on the projector (see page 20).

• Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu (see page 31).

Projected images are

distorted.

• Adjust the projector and the screen so that they are perpendicular to each other (see page 8).

Projected images are dark. • Adjust BRIGHTNESS and CONTRAST in the IMAGE menu (see page 27).

• Replace the lamp (see page 32).

Projected images are blurred. • Adjust the focus (see page 16 and 19).

• Clean the lens.

• Press the or button on the remote control to eliminate flicker.

• Adjust TRACKING and PHASE in the SIGNAL menu (see page 31).

• Adjust BRIGHTNESS and CONTRAST in the IMAGE menu (see page 27).

• Adjust the projector and the screen so that they are perpendicular to each other (see page 8).

White dots are seen on

projected images.

Black dots are seen on

projected images.

• This symptom is normal for a DLP

projector and is not a malfunction. (A very small number of pixels

may stay lit or out, but it is not a malfunction. Pixels of 99.99% or more are effective.)

Rainbow effect is seen on

projected images.

• This is due to color breaking noise that occurs in a DLP

system and is not a malfunction.

Fine streaks are seen on

projected images.

• This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace

the focus a little.

Projected images become

wavy.

• Connect the cable plugs to external equipments securely.

• Keep the projector away from equipments that emit interfering radio waves.

• When the keystone adjustment is carried out, the image may not be displayed correctly because of the type

of input signal. This isn’t a product malfunction. In this case, readjust the keystone so that the amount of

keystone correction is as small as possible.

Hue is not appropriate. • Check that the cable connected to the external equipment is not defective.

Tint in projected images is

incorrect.

• Check that D-SUB INPUT in the SIGNAL menu is correctly set (see page 26).

• Check that the cable connected to the external equipment is not defective.

Only the motion areas in the

images supplied from the

computer are not displayed.

• This is caused by the computer being used. Contact the manufacturer of your computer.

Projected images are

obscured.

• Match the output resolution of your computer with the resolution of the projector. For the method to

change the output resolution of the computer, contact the manufacturer of your computer (see page 40).

• Some images and texts appear obscured during the keystone adjustment. In such cases, use the projector

without applying the keystone adjustment (see page 17).

Problem Solution

Others

If the following problem occurs after the lamp is replaced, check the following first.

Problem Solution

The exhaust vents emit warm

air.

• This air comes out after cooling the inside of the projector. It may feel hot, but this is not a malfunction.

The menu can not be used. • The microcomputers inside the projector may be wrongly operating because of noise.

➜Press the STANDBY/ON button to turn off the lamp and unplug the power cable from the wall outlet.

Wait about 10 minutes, plug the power cable in, and try again.

“TEMPERATURE!!” is

displayed.

• This indication appears when the ambient temperature rises high. When the ambient temperature stays

high, the lamp goes out.

➜Eliminate any causes of the rise in the ambient temperature.

• This indication appears when the air intake or exhaust vent is blocked. When they are kept blocked, the

lamp goes out.

➜Remove the objects blocking the air intake or exhaust vent.

The mark appears.

• This mark appears when ineffective operation is carried out. This is not a product malfunction.

The remote control does not

function easily or at all.

• Check that the battery is loaded in the remote control or the battery is not weak (see page 4).

• Check that the remote control sensor is not exposed to direct sunlight or fluorescent light.

• Use the remote control within its operation range (see page 7).

• Use the remote control at least 10 cm away from the projector.

Abnormal sound is heard. • Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions.

Problem Solution

The projector does not turn

on.

• Fit the lamp cover securely (see page 33).

• Reset the lamp operating time (see page 33).

The STATUS indicator

blinks.

• Reset the lamp operating time (see page 33).

This projector has two indicators, each of which shows the operation condition of the projector.

Refer to Troubleshooting for additional indication signals.

◆ Normal conditions

◆ Abnormal conditions

*1: When LAMP MODE of the SETUP menu is set to CINEMA.

*2: When LAMP MODE is set to STANDARD, this duration will be decreased to 2000 hours.

POWER STATUS CONDITION NOTE

Steady red Off

Stand-by.

Steady green Blinking green

Warming up period (about 1 minute).

The STANDBY/ON button cannot be used

until the STATUS indicator is steady green.

Steady green Steady green

The projector is ready.

Steady red Blinking green

Cooling down period (lasts under 2 minutes; normal when

shutting down).

Do not unplug the projector until the

STATUS indicator is off.

POWER STATUS CONDITION SOLUTION

Steady green

Steady red

Blinking orange

Abnormal temperature

• The ventilation grilles are clogged with dust or dirt.

• The room temperature is high.

• Clean the ventilation grilles.

• Relocate the projector to a cooler place.

• Remove any objects blocking the

ventilation grilles.

Steady red Blinking green

Abnormal when it occurs except while shutting down. The

protection circuit is working or the lamp is in an abnormal

condition.

• Wait until the STATUS indicator goes out,

then press the STANDBY/ON button.

• If the above solution is not effective,

replace the lamp.

Steady green Blinking green/red

Lamp operation time warning. (Total lamp operation time

reached 2250 hours

while the power was on.)

Replace the lamp.

Change with a new lamp if this problem

recurs.

Steady red Blinking red

Lamp operation time warning. (Total lamp operation time

reached 2250 hours

while the power was off.)

Steady red Steady red

Lamp operation time warning. (Total lamp operation time

reached 3000 hours

*1, *2

while the power was off.)

Blinking

green/red

Off

The lamp cover isn’t closed. Close the cover correctly.

Blinking

green/red

Steady or Blinking

Abnormal. Contact your dealer.

STATUS indicator

POWER indicator

STANDBY/ON button

Indicators

◆ Projector specifications

The specifications and outside appearance of the projector are subject to change without prior notice.

Type DLP™ projector

Model DPX-830

Display Technology 0.65-inch Single chip DMD

Pixel 1280 × 768 = 983040 pixels

Projection lens F 2.4 – 2.6 f= 23 – 27.6 mm

Light-source lamp 200 W

Image size (Projection distance) 40" min. to 275" max. (Projection distance 1.4 to 10.1 m (16:9 screen))

Maximum resolution Computer signal Maximum resolution: 1280 x 1024 dots (Analog) / compressed

Panel resolution: 1280 × 768 dots

Video signal NTSC / PAL / SECAM / 4.43NTSC / PAL-M / PAL-N / PAL-60

Component signal 480i, 480p, 576i, 576p, 720p, 1080i

Panel resolution: 1280 × 768 dots

Input terminal [Signal type]

Analog RGB

Digital RGB

Video input

S-Video input

Component video input

[Terminal type]

D-SUB 15P

HDMI

RCA × 1

RCA × 3, D-SUB 15P

[Line]

Control terminal/

Others

USB For service person

SERIAL RS-232C (8P): For service person

TRIGGER DC 12 V, Max.200 mA (Stereo mini jack)

Operating temperatures +41°F (+5°C) to +95°F (+35°C)

Rated voltage AC100 - 240 V, 50/60 Hz

Power consumption 280 W / 2.9 A

Power consumption (standby) 8 W

Dimensions 360 mm (W) × 102 mm (H) × 290 mm (D) *Not including protrusions.

Weight 3.9 kg

Others S-video input Luminance signal: Vp-p=1.0 V 75 Ω (negative sync)

Chrominance signals: Vp-p=0.286 V 75 Ω (burst signal)

Video input Vp-p=1.0 V 75 Ω (negative sync)

Component video

input

: Vp-p=1.0 V 75 Ω (Y) (negative sync)

Vp-p=0.7 V 75 Ω (C

, C

)

Analog RGB input RGB: Vp-p=0.7 V 75 Ω (negative sync)

HD: TTL-level (negative or positive polarity)

VD: TTL-level (negative or positive polarity)

Digital input (HDMI) HDMI interface (TMDS single link)

Specifications

◆ Composite / S-video signal specifications

Signal mode Resolution

(H × V)

Horizontal frequency

(kHz)

Vertical frequency

(Hz)

Default mode for

16:9 screen

(H × V)

Default mode for

4:3 screen

(H × V)

Through mode

(H × V)

TV60 (525i) – 15.73 59.94 1280 × 720 1024 × 576 –

TV50 (625i) – 15.63 50.00 1280 × 720 1024 × 576 –

◆ Component signal specifications

Signal mode Resolution

(H × V)

Horizontal frequency

(kHz)

Vertical frequency

(Hz)

Default mode for

16:9 screen

(H × V)

Default mode for

4:3 screen

(H × V)

Through mode

(H × V)

480i (525i) – 15.73 59.94 1280 × 720 1024 × 576 –

576i (625i) – 15.63 50.00 1280 × 720 1024 × 576 –

480p (525p) – 31.47 59.94 1280 × 720 1024 × 576 –

576p (625p) – 31.25 50.00 1280 × 720 1024 × 576 –

720p 60 (750p 60) – 45.00 60.00 1280 × 720 1024 × 576 –

720p 50 (750p 50) – 37.50 50.00 1280 × 720 1024 × 576 –

1080i 60 (1125i 60) – 33.75 60.00 1280 × 720 1024 × 576 –

1080i 50 (1125i 50) – 28.13 50.00 1280 × 720 1024 × 576 –

◆ Digital RGB / Component signal specifications

Signal mode Resolution

(H × V)

Horizontal frequency

(kHz)

Vertical frequency

(Hz)

Default mode for

16:9 screen

(H × V)

Default mode for

4:3 screen

(H × V)

Through mode

(H × V)

480p (525p) – 31.47 59.94 1280 × 720 1024 × 576 –

576p (625p) – 31.25 50.00 1280 × 720 1024 × 576 –

720p 60 (750p 60) – 45.00 60.00 1280 × 720 1024 × 576 –

720p 50 (750p 50) – 37.50 50.00 1280 × 720 1024 × 576 –

1080i 60 (1125i 60) – 33.75 60.00 1280 × 720 1024 × 576 –

1080i 50 (1125i 50) – 28.13 50.00 1280 × 720 1024 × 576 –

VGA 60 640 × 480 31.47 59.94 960 × 720 1024 × 768 –

◆ Analog RGB signal specifications

Signal mode Resolution

(H × V)

Horizontal frequency

(kHz)

Vertical frequency

(Hz)

Default mode for

16:9 screen

(H × V)

Default mode for

4:3 screen

(H × V)

Through mode

(H × V)

576i (625i)

– 15.63 50.00 1280 × 720 1024 × 576 –

720p 60 (750p 60) – 45.00 60.00 1280 × 720 1024 × 576 –

720p 50 (750p 50) – 37.50 50.00 1280 × 720 1024 × 576 –

1080i 60 (1125i 60) – 33.75 60.00 1280 × 720 1024 × 576 –

1080i 50 (1125i 50) – 28.13 50.00 1280 × 720 1024 × 576 –

PC98 640 × 400 24.82 56.42 1152 × 720 1024 × 640 640 × 400

CGA70 640 × 400 31.47 70.09 1152 × 720 1024 × 640 640 × 400

CGA84 640 × 400 37.86 84.13 1152 × 720 1024 × 640 640 × 400

VGA60 640 × 480 31.47 59.94 960 × 720 1024 × 768 640 × 480

VGA72 640 × 480 37.86 72.81 960 × 720 1024 × 768 640 × 480

VGA75 640 × 480 37.50 75.00 960 × 720 1024 × 768 640 × 480

VGA85 640 × 480 43.27 85.01 960 × 720 1024 × 768 640 × 480

SVGA56 800 × 600 35.16 56.25 960 × 720 1024 × 768 800 × 600

SVGA60 800 × 600 37.88 60.32 960 × 720 1024 × 768 800 × 600

SVGA72 800 × 600 48.08 72.19 960 × 720 1024 × 768 800 × 600

SVGA75 800 × 600 46.88 75.00 960 × 720 1024 × 768 800 × 600

SVGA85 800 × 600 53.67 85.06 960 × 720 1024 × 768 800 × 600

XGA60 1024 × 768 48.36 60.00 960 × 720 1024 × 768

XGA70 1024 × 768 56.48 70.07 960 × 720 1024 × 768

XGA75 1024 × 768 60.02 75.03 960 × 720 1024 × 768

XGA85 1024 × 768 68.68 85.00 960 × 720 1024 × 768

MAC13 640 × 480 35.00 66.67 960 × 720 1024 × 768 640 × 480

MAC16 832 × 624 49.72 74.55 960 × 720 1024 × 768 832 × 624

MAC19 1024 × 768 60.24 75.02 960 × 720 1024 × 768

SXGA60 1280 × 1024 60.02 63.98 900 × 720 960 × 768

*1: When ASPECT in the INITIAL menu is set to DEFAULT, and SCREEN ASPECT in the SETUP menu is set to 16:9.

*2: When ASPECT in the INITIAL menu is set to DEFAULT, and SCREEN ASPECT in the SETUP menu is set to 4:3.

*3: Available with RGB-CS (4 line) sources from SCART terminal.

*4: Same resolution as the DEFAUL mode depending on the each SCREEN ASPECT.

Important

• This projector can recognize 1280 × 768 pixels as the maximum resolution, however, it is programmed to recognize 1280 ×

720 or 1024 × 768 pixels as the normal resolution depending on the screen aspect.

• If the resolution and frequency of your computer are not shown on the table, find the compatible resolution and frequency by

changing the resolution of your computer.

• In the case of XGA, the right side of the image may not appear. In this case, adjust TRACKING in the SIGNAL menu.

• TV60 and TV50 are equivalent to 480i and 576i respectively. When these signals are input to the VIDEO or S-VIDEO signal,

the signal mode is indicated as TV60 or TV50. When they are input to the COMPONENT terminal, the signal mode is

indicated as 480i or 576i.

• This projector cannot be connected to other equipment via an RGB-CS (4 line) connection.

Connectors

SERIAL (8-pin) D-SUB (Mini D-SUB 15-pin) HDMI (HDMI - 19 pin)

◆ Dimension drawings

Pin No. Name I / O

1TXDIN

2––

3––

4 GND –

5––

6––

7 RXD OUT

8––

Pin No. Spec. Pin No. Spec.

1 R(RED) / CR 9 –

2 G(GREEN) / Y 10 GND

3 B(BLUE) / CB 11 GND

4 GND 12 DDC Data

5 GND 13 HD/CS

6 GND 14 VD

7 GND 15 DDC Clock

8 GND

Pin No. Spec. Pin No. Spec.

1 TMDS Data2+ 11 TMDS Clock

Shield

2TMDS Data2

Shield

12 TMDS Clock-

3 TMDS Data2- 13 -

4 TMDS Data1+ 14 -

5TMDS Data1

Shield

15 SCL

6 TMDS Data1- 16 SDA

7 TMDS Data0+ 17 DDCGround

8 TMDS Data02

Shield

18 +5 V Power

9 TMDS Data0- 19 Hot Plug Detect

10 TMDS Clock+

191

290

360

102

(Unit: mm)

Yamaha DPX-1 Handleiding

Merk: Yamaha

Model: DPX-1

Categorie: Dataprojectoren

Type: Handleiding

Deze handleiding is ook geschikt voor

Download PDF

rapport

in andere talen

English: Yamaha DPX-1 User manual
italiano: Yamaha DPX-1 Manuale utente
français: Yamaha DPX-1 Manuel utilisateur
Deutsch: Yamaha DPX-1 Benutzerhandbuch
dansk: Yamaha DPX-1 Brugermanual
suomi: Yamaha DPX-1 Ohjekirja
svenska: Yamaha DPX-1 Användarmanual
Türkçe: Yamaha DPX-1 Kullanım kılavuzu
română: Yamaha DPX-1 Manual de utilizare

Yamaha DPX-1 Handleiding

Deze handleiding is ook geschikt voor

Yamaha DPX-1 Handleiding

in andere talen

Gerelateerde artikelen

Andere documenten