Yamaha RX-V430RDS de handleiding

Merk: Yamaha

Model: RX-V430RDS

Categorie: AV-ontvangers

Type: de handleiding

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia

V890260

RX-V430RDS

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

RX-V430RDS

AV Receiver

Ampli-tuner audio-vidéo

0100V430(GB)-cv1 1/18/02, 3:59 PM1

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place with at least 30 cm on the top, 20 cm on the

left and right, and 10 cm at the back of this unit

— away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds. To prevent fire or electrical

shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this

unit in a environment with high humidity (i.e. a room

with a humidifier) to prevent condensation inside

this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

–

Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may

cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper,

tablecloth, curtain, etc. in order not to obstruct

heat radiation. If the temperature inside this unit

rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than

specified is dangerous and may cause fire,

damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any

damage resulting from use of this unit with a

voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an

electrical storm.

14 Take care of this unit so that no foreign objects

and/or liquid drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

16 When not planning to use this unit for long

periods of time (i.e. vacation), disconnect the AC

power plug from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding

that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

19 VOLTAGE SELECTOR (China and General models

only)

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage

BEFORE plugging into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is called

the standby mode. In this state, this unit is designed to

consume a very small quantity of power.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K.

Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED

IN ACCORDANCE WITH THE FOLLOWING

CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

CAUTION

0101V430_Cau_EN(GB) 1/19/02, 8:03 PM2

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

CONTENTS

INTRODUCTION

CONTENTS ............................................................ 1

FEATURES ............................................................. 2

GETTING STARTED ............................................ 3

Checking the package contents ................................. 3

Installing batteries in the remote control ................... 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel ................................................................ 4

Remote control .......................................................... 6

Using the remote control ........................................... 7

Front panel display .................................................... 8

PREPARATION

SPEAKER SETUP ................................................. 9

Speakers .................................................................... 9

Speaker placement .................................................... 9

Connecting the speakers .......................................... 10

CONNECTIONS .................................................. 13

Before connecting components ............................... 13

Connecting video components ................................ 14

Connecting audio components ................................ 16

Connecting the antennas ......................................... 17

Connecting an external decoder .............................. 18

Connecting the power supply cords ........................ 18

Turning on the power .............................................. 19

SPEAKER MODE SETTINGS .......................... 20

ADJUSTING SPEAKER OUTPUT LEVELS .. 21

Using the test tone ................................................... 21

BASIC OPERATION

BASIC PLAYBACK ............................................ 23

Input modes and indications .................................... 25

Selecting a sound field program .............................. 26

DIGITAL SOUND FIELD PROCESSING

(DSP) ................................................................. 29

Understanding sound fields ..................................... 29

Hi-Fi DSP programs ................................................ 29

CINEMA-DSP ...................................................... 30

Sound design of CINEMA-DSP ............................. 30

CINEMA-DSP programs ........................................ 32

TUNING ................................................................ 34

Automatic and manual tuning ................................. 34

Presetting stations .................................................... 35

Tuning in to a preset station .................................... 37

Exchanging preset stations ...................................... 37

RECEIVING RDS STATIONS ........................... 38

Description of RDS data ......................................... 38

Changing the RDS mode ......................................... 38

PTY SEEK function ................................................ 39

EON function .......................................................... 39

SLEEP TIMER ..................................................... 40

Setting the sleep timer ............................................. 40

Canceling the sleep timer ........................................ 40

RECORDING ....................................................... 41

ADVANCED OPERATION

SET MENU ........................................................... 42

Adjusting the items on the SET MENU .................. 42

1 SPEAKER SET (speaker mode settings) ............ 43

2 LFE LEVEL ........................................................ 44

3 SP DLY TIME (speaker delay time) ................... 45

4 D. RANGE (dynamic range) ............................... 45

5 L/R BALANCE (balance of the main left and

right speakers) ..................................................... 45

6 HP TONE CTRL (headphone tone control) ........ 45

7 I/O ASSIGN (input/output assignment) .............. 46

8 INPUT MODE (initial input mode) .................... 46

9 DISPLAY SET .................................................... 46

10MEM. GUARD (memory guard) ........................ 46

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS ....................................................... 47

ADJUSTING THE DELAY TIME ..................... 48

ADJUSTING THE PARAMETER SETTINGS

FOR PRO LOGIC

MUSIC ......................... 49

Changing parameter settings ................................... 49

PRO LOGIC Music parameter descriptions ....... 49

ADDITIONAL INFORMATION

TROUBLESHOOTING ...................................... 50

GLOSSARY .......................................................... 54

SPECIFICATIONS .............................................. 56

0102V430_1-8_EN(GB) 1/19/02, 8:03 PM1

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS” and “DTS Digital Surround” are registered trademarks of

Digital Theater Systems, Inc.

FEATURES

Built-in 5-channel power amplifier

◆ Minimum RMS output power

(0.06% THD, 20 Hz – 20 kHz, 8Ω)

[U.S.A. and Canada models]

Main: 75 W + 75 W

Center: 75 W

Rear: 75 W + 75 W

[Other models]

Main: 65 W + 65 W

Center: 65 W

Rear: 65 W + 65 W

Multi-mode digital sound field

processing

◆ Dolby Pro Logic/Dolby Pro Logic Decoder

◆ Dolby Digital/Dolby Digital + Matrix 6.1

Decoder

◆ DTS/DTS + Matrix 6.1 Decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

Technology and Dolby Pro Logic, Dolby Digital

or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station random access preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (Preset

editing)

Other features

◆ 96-kHz/24-bit D/A converter

◆ “SET MENU” for optimizing this unit for your

Audio/Video system

◆ Test tone generator for easier speaker balance

adjustment

◆ 6-channel external decoder input

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

■ About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this

manual.

• This manual is printed prior to production. Design and specifications are subject to change in part for the reason of the improvement

in operativity ability, and others. In this case, the product has priority.

0102V430_1-8_EN(GB) 1/19/02, 8:03 PM2

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

POWER

6CH INPUTSLEEP

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

– PRESET

A/B/C/D/E

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

SET MENU

LEVEL

DSP

+–

STEREO

EFFECT

MUTE

VOLUME

TEST

/ DTS

SUR.

Installing batteries in the remote

control

Insert the batteries in the correct direction by aligning the

+ and – marks on the batteries with the polarity markings

(+ and –) inside the battery compartment.

1 Press the part and slide off the battery

compartment cover.

2 Insert the 2 supplied batteries (AA, R06,

UM-3) according to the polarity markings on

the inside of the battery compartment.

3 Slide the cover back on so that it snaps into

place.

■ Notes on batteries

• Change all of the batteries if you notice a decrease in

the operating range of the remote control, that the

indicator does not flash, or the light becoming dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean

the battery compartment thoroughly before installing

new batteries.

AM loop antenna

(Europe, U.K., Australia and

Singapore models)

Indoor FM antenna

(U.S.A., Canada, China,

Korea and General models)

Batteries (2)

(AA, R06, UM-3)

Remote control

GETTING STARTED

Checking the package contents

Check your package to make sure it contains the following items.

75-ohm/300-ohm antenna

adapter (U.K. model)

A/V cable (U.S.A., Canada

and Australia models)

0102V430_1-8_EN(GB) 1/19/02, 8:03 PM3

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

–+ –+

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

START

EON

RDS MODE/FREQ

MODE

PTY SEEK

EFFECT

1234567

90 e

irt8qyuw

START

EON

RDS MODE/FREQ

MODE

PTY SEEK

po sa

CONTROLS AND FUNCTIONS

Front panel

1 STANDBY/ON

Turns this unit on, or set it to the standby mode. When

you turn this unit on, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit will consume a small amount of

power in order to receive infrared-signals from the

remote control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit.

4 INPUT MODE

Sets the priority for the types of input signals (AUTO,

DTS, ANALOG) to receive when one component is

connected to two or more input jacks. Priority cannot be

set when 6CH INPUT is selected as the input source.

5 INPUT l / h

Selects the input source you want to listen to or watch.

6 VOLUME

Controls the output level of all audio channels.

This does not affect the OUT (REC) level.

7 6CH INPUT

Selects the audio source connected to the 6CH INPUT

jacks. This audio takes priority over the source selected

with INPUT l / h (or the input selector buttons on the

remote control).

(U.K. and Europe model)

0102V430_1-8_EN(GB) 1/19/02, 8:03 PM4

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

8 SILENT (PHONES jack)

Allows you enjoy DSP effect for private listening with

headphones. When you connect headphones, no signals

are output to the speakers.

9 STEREO/EFFECT

Switches between normal stereo and DSP effect

reproduction. When STEREO is selected, 2-channel

signals are directed to the main left and right speakers

without effect sounds and all Dolby Digital and DTS

signals (except the LFE channel) are mixed down to the

main left and right speakers.

0 PROGRAM l / h

Selects the DSP program.

q MEMORY (MAN’L/AUTO FM)

Stores the current station in the memory.

w TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.

e FM/AM

Switches the reception band between FM and AM.

r PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h

between selecting a preset station number and tuning (the

colon (:) turns on or off).

This button is also used to exchange the assignment of

two preset stations with each other.

t PRESET/TUNING l / h

Selects preset station numbers 1 to 8 when the colon (:)

appears in the front panel display.

Selects the tuning frequency when the colon (:) does not

appear.

y A/B/C/D/E

Selects preset station groups A to E.

u BASS

Adjusts the low-frequency response for the main left and

right channels.

Turn right to increase or turn left to decrease the low-

frequency response.

i TREBLE

Adjusts the high-frequency response for the main left and

right channels.

Turn right to increase or turn left to decrease the high-

frequency response.

o RDS MODE/FREQ (U.K. and Europe models)

When an RDS station is received, press this button to

change the display mode among the PS mode, PTY mode,

RT mode, CT mode (if the station offers those RDS data

service) and/or frequency display mode in turn.

p PTY SEEK MODE (U.K. and Europe models)

Press this button to set the unit in the PTY SEEK mode.

a PTY SEEK START (U.K. and Europe models)

Press this button to begin searching for a station after the

desired program type has been selected in the PTY SEEK

mode.

s EON (U.K. and Europe models)

Press this button to select the desired program type

(NEWS, INFO, AFFAIRS, SPORT) when you want to

tune in to a radio program of that type automatically.

0102V430_1-8_EN(GB) 1/19/02, 8:03 PM5

CONTROLS AND FUNCTIONS

POWER

6CH INPUTSLEEP

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

– PRESET +

A/B/C/D/E

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

SET MENU

LEVEL

DSP

+–

STEREO

EFFECT

MUTE

VOLUME

TEST

/ DTS

SUR.

Remote control

This section describes the remote control controls and

their functions.

1 POWER

Turns this unit on, or set it to the standby mode.

2 SLEEP

Sets the sleep timer.

3 Input selector buttons

Select the input source.

4 PRESET +/–

Selects preset station numbers 1 to 8.

5 DSP program

Select DSP programs. Press a button repeatedly to select a

DSP program within that group.

6 LEVEL

Selects the effect speaker channel to be adjusted.

7 Multi control section

Used when changing the setting and to implement the

settings.

8 TEST

Outputs the test tone to adjust the speaker levels.

9 MUTE

Mutes the sound. Press again to restore the audio output

to the previous volume level.

0 VOLUME h/g

Increases or decreases the volume level.

q 6CH INPUT

Selects the audio source connected to the 6CH INPUT

jacks.

w A/B/C/D/E

Selects preset station groups A to E.

e SET MENU

Selects the SET MENU mode.

r STEREO/EFFECT

Switches between normal stereo and DSP effect

reproduction. When STEREO is selected, 2-channel

signals are directed to the main left and right speakers

without effect sounds and all Dolby Digital and DTS

signals (except the LFE channel) are mixed down to the

main left and right speakers.

0102V430_1-8_EN(GB) 1/19/02, 8:03 PM6

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

POWER

6CH INPUTSLEEP

DVD D-TV/CBL

VCR

V-AUX

CD TUNER MD/CD-R

–

PRESET

A/B/C/D/E

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

SET MENU

LEVEL

–

DSP

STEREO

EFFECT

MUTE

VOLUME

TEST

/ DTS

SUR.

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING MODE

30° 30°

Approximately 6 m (20 feet)

Using the remote control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

0102V430_1-8_EN(GB) 1/19/02, 8:03 PM7

CONTROLS AND FUNCTIONS

LCR

RC RR

LFE

VIRTUAL

DSP

PCM

MATRIX

SILENT

DIGITAL

EON

PS PTY

PTY HOLD

MUTE

SLEEP

STEREO

TUNED

MEMORY

AUTO

PRO LOGIC

VOLUME

DTS

MOVIE

THTR

ENTERTAINMENT

DOLBY DIGITAL

PRO

LOGIC

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

1234

5789

qwert y

1 Processor indicators

Lights up when the t, g, VIRTUAL,

PRO LOGIC

DSP

or MATRIX are activated.

2 Input source indicator

Shows the current input source with a cursor.

3 MUTE indicator

Flashes while the MUTE function is on.

4 VOLUME level indicator

Indicates the volume level.

5 v indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

6 SILENT indicator

Lights up when headphones are connected while the

digital sound field processor is on.

7 Headphones indicator

Lights up when headphones are connected.

8 DSP program indicators

The name of the selected DSP program lights up when the

ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2 or V/DTS SURROUND DSP program is

selected.

9 Multi-information display

Shows the current DSP program name and other

information when adjusting or changing settings.

0 RDS indicator (U.K. and Europe models)

The name(s) of the RDS data offered by the currently

received RDS station light(s) up.

EON indicator lights up when an RDS station that offers

the EON data service is being received.

PTY HOLD indicator lights up while searching for

stations in the PTY SEEK mode.

q STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

w TUNED indicator

Lights up when this unit is tuned to a station.

e MEMORY indicator

Flashes to show a station can be stored.

r AUTO indicator

Shows that this unit is in the automatic tuning mode.

t SLEEP indicator

Lights up while the sleep timer is on.

y Input channel indicator

Indicates the channel components of input signals being

received.

Front panel display

(U.K. and Europe models)

0102V430_1-8_EN(GB) 1/19/02, 8:03 PM8

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

Speakers

This unit has been designed to provide the best sound-

field quality with a 5-speaker system, using main left and

right speakers, rear left and right speakers and a center

speaker. If you use different brands of speakers (with

different tonal qualities) in your system, the tone of a

moving human voice and other types of sound may not

shift smoothly. We recommend that you use speakers

from the same manufacturer or speakers with the same

tonal quality.

The main speakers are used for the main source sound

plus effect sounds. They will probably be the speakers

from your present stereo system. The rear speakers are

used for effect and surround sounds. The center speaker is

for the center sounds (dialog, vocals, etc.).

The main speakers should be high-performance models

and have enough power-handling capacity to accept the

maximum output of your audio system. The other

speakers do not have to be equal to the main speakers. For

precise sound localization, however, it is ideal to use the

models of equivalent performance with the main

speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is

effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the LFE

(low-frequency effect) channel with high fidelity when

playing back Dolby Digital or DTS signals. The

YAMAHA Active Servo Processing Subwoofer System is

ideal for natural and lively bass reproduction.

PREPARATION

Speaker placement

Refer to the following diagram when you place the

speakers.

■ Main speakers

Place the main left and right speakers an equal distance

from the ideal listening position. The distance between

each speaker and each side of the video monitor should

also be the same.

■ Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible (such as directly over or under the

monitor) and centrally between the main speakers.

■ Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (6 feet) above the

floor.

■ Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the main speakers. Turn it

slightly toward the center of the room to reduce wall

reflections.

Note

• If you do not use any of effect speakers (rear and/or center),

change the settings of SPEAKER SET items at the SET MENU

to designate the signals to other terminals you connect speakers

to.

CAUTION

Use magnetically shielded speakers. If this type of

speakers still creates the interference with the monitor,

place the speakers away from the monitor.

Main

speaker (L)

1.8 m (6 feet)

Rear speaker (L)

Rear speaker (R)

Subwoofer

Main speaker (R)Center speaker

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM9

SPEAKER SETUP

Connecting the speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/

or the speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers

in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables

running side by side. One cable is colored or shaped

differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

■ Connecting to the SPEAKERS terminals

(Europe and U.K. models)

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

(Other models)

1 Open the tab.

2 Insert one bare wire into the hole of each

terminal.

3 Return the tab to secure the wire.

(U.S.A., Canada, Australia, China, Korea and General models)

• Banana plug connections are also possible. First, open the tab

and then insert the banana plug connector into the end of the

corresponding terminal.

■ MAIN SPEAKERS terminals

A front speaker system can be connected to these terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

10 mm (3/8”)

Banana plug

Red: positive (+)

Black: negative (–)

Red: positive (+)

Black: negative (–)

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM10

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

SUB

WOOFER

OUTPUT

SPEAKERS

MAIN

REAR

(SURROUND)

CENTER

–

L L

R R

Subwoofer

system

Center

speaker

Right

Rear speaker

■ SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,

connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or

rear channels are directed to this jack in accordance with your SPEAKER SET selections. The LFE (low-frequency

effect) signals generated when Dolby Digital or DTS is decoded are also directed to this jack in accordance with your

SPEAKER SET selections.

Notes

• The cut-off frequency of the SUBWOOFER jack is 90 Hz.

• If you do not use a subwoofer, designate the signals to the main left and right speakers by changing the setting of SPEAKER SET

item “1D BASS” on the SET MENU to MAIN.

• Use the control on the subwoofer to adjust its volume level. It is also possible to adjust the volume level by using this unit’s remote

control (see “ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS” on page 47).

Main speaker

Right Left

Left

The diagram shows the speaker layout in the listening

room.

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM11

SPEAKER SETUP

SET BEFORE POWER ON

MAIN

: 8Ω

MIN. /SPEAKER

CENTER

: 8Ω

MIN. /SPEAKER

REAR

: 8Ω

MIN. /SPEAKER

MAIN

: 4Ω

MIN. /SPEAKER

CENTER

: 6Ω

MIN. /SPEAKER

REAR

: 6Ω

MIN. /SPEAKER

SPEAKERS

MAIN

REAR

(SURROUND)

CENTER

––

IMPEDANCE SELECTOR

Switch

position

Left

Right

Speaker

Main

Center

Rear

Main

Center

Rear

Impedance level

The impedance of each speaker must

be 4 Ω or higher.

The impedance must be 6 Ω or

higher.

The impedance of each speaker must

be 6 Ω or higher.

The impedance of each speaker must

be 8 Ω or higher.

The impedance must be 8 Ω or

higher.

The impedance of each speaker must

be 8 Ω or higher.

(U.S.A. model)

■ IMPEDANCE SELECTOR switch

WARNING

Do not change setting of the IMPEDANCE SELECTOR switch when the power of this unit is on, this may damage

the unit. If this unit fails to turn on when STANDBY/ON (or POWER) is pressed, the IMPEDANCE SELECTOR

switch may not be fully slid to either position. If so, slide the switch all the way to either position when this unit is in

the standby mode.

Select the switch position (left or right) according to the impedance of the speakers in your system. Be sure to move this

switch only when this unit is in the standby mode.

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM12

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

Before connecting components

CAUTION

Do not connect this unit or other components to the

mains power until all connections between the

components have been completed.

• Be sure all connections are made correctly, that is to

say L (left) to L, R (right) to R, “+” to “+” and “–” to

“–”. Some components require different connection

methods and have different jack names. Refer to the

operation instructions for each component to be

connected to this unit.

• When you connect other YAMAHA audio components

(such as a tape deck, MD recorder and CD player or

changer), connect them to the jack with the same

number labels as !, #, $ etc. YAMAHA applies this

labeling system to all its products.

• After you have completed all connections, check them

again to make sure they are correct.

• The name of jack corresponds to input selector.

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of

digital signals through either coaxial or fiber optic cables.

You can use the digital jacks to input PCM, Dolby Digital

and DTS bitstreams. To enjoy multi-channel sound track

of DVD software, etc. with DSP effect, you need to make

digital connection. All digital input jacks are acceptable

for 96-kHz sampling digital signals.

Note

• The OPTICAL jacks on this unit conform to the EIA standard.

If you use a fiber optic cable that does not conform to this

standard, this unit may not function properly.

DIGITAL

INPUT

6CH INPUT AUDIO

TUNER

ANT

GND

75Ω UNBAL.

VIDEO

COAXIAL

OPTICAL

DVD

VCR

OUT

D-TV/CBL

/CD-R

(PLAY)

V-A UX

SUB

WOOFER

SUB

WOOFER

MONITOR

OUT

SURROUND

CENTER

MAIN

OUT

(REC)

OUTPUTAUDIO

SPEAKERS

MAIN

REAR

(SURROUND)

CENTER

––

DIGITAL INPUT jacks

(pages 13-16)

6CH INPUT jacks

(page 18)

Video component jacks

(pages 14-15)

Audio component jacks

(page 16)

SUBWOOFER OUTPUT jack

(page 11)

AC OUTLETS (page 18)

Antenna input terminals

(page 17)

SPEAKERS terminals

(pages 10-11)

(U.S.A. model)

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM13

CONNECTIONS

Connecting video components

Refer to the connection examples on the next page.

■ Connecting a video monitor

Connect the video input jack on your video monitor to the

MONITOR OUT VIDEO jack.

■ Connecting a DVD player

Connect the optical digital audio signal output jack on

your component to the DIGITAL INPUT jack and

connect the video signal output jack on the component to

the VIDEO jack on this unit.

• The AUDIO jacks are available for a video component which

does not have optical digital output jack. However, multi-

channel reproduction cannot be obtained with audio signals

input from AUDIO jacks.

■ Connecting a digital TV/cable TV

Connect the video signal output jack on the component to

the VIDEO jack on this unit.

Connect the audio signal output jacks on your video

component to the AUDIO jacks on this unit.

■ Connecting another video

component

Connect the audio signal output jacks on your video

component to the AUDIO jacks and connect the video

signal output jack on the component to the VIDEO jack

on this unit.

■ Connecting a VCR or DVR (digital

video recorder)

Connect the audio signal input jacks on your video

component to the AUDIO OUT jacks and connect the

video signal input jack on the video component to the

VIDEO OUT jack on this unit for picture recording.

Connect the audio signal output jacks on your component

to the AUDIO IN jacks and connect the video signal

output jack on the component to the VIDEO IN jack on

this unit to play a source from your recording component.

Note

• Once you have connected a recording component to this unit,

keep its power turned on while using this unit. If the power is

off, this unit may distort the sound from other components.

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM14

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

DIGITAL

INPUT

6CH INPUT AUDIO

TUNER

ANT

GND

75Ω UNBAL.

VIDEO

COAXIAL

OPTICAL

DVD

VCR

OUT

D-TV/CBL

/CD-R

(PLAY)

V-AUX

SUB

WOOFER

SUB

WOOFER

MONITOR

OUT

SURROUND

CENTER

MAIN

OUT

(REC)

OUTPUTAUDIO

VIDEO

INPUT

VIDEO

OUTPUT

OPTICAL

OUTPUT

V V

AUDIO

INPUT

VIDEO

OUTPUT

VIDEO

INPUT

AUDIO

OUTPUT

VIDEO

OUTPUT

AUDIO

OUTPUT

AUDIO

OUTPUT

VIDEO

OUTPUT

indicates video cables

indicates optical cables

indicates right analog cables

indicates left analog cables

indicates signal direction

Video monitor

VCR

DVD player

TV/digital TV/

cable TV

Another video

component

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM15

CONNECTIONS

Connecting audio components

■ Connecting a CD player

Connect the coaxial digital output jack on your CD player

to the DIGITAL INPUT CD jack.

• The AUDIO jacks are available for a CD player which does not

have coaxial digital output jack.

■ Connecting a CD recorder or MD

recorder

Connect the input jacks on your CD recorder or MD

recorder to the MD/CD-R OUT (REC) jacks for analog

recording.

Connect the output jacks on your CD recorder or MD

recorder to the MD/CD-R IN (PLAY) jacks to play a

source from your recording component.

Note

• Once you have connected a recording component to this unit,

keep its power turned on while using this unit. If the power is

off, this unit may distort the sound from other components.

DIGITAL

INPUT

6CH INPUT AUDIO

TUNER

ANT

GND

75Ω UNBAL.

VIDEO

COAXIAL

OPTICAL

DVD

VCR

OUT

D-TV/CBL

/CD-R

(PLAY)

V-AUX

SUB

WOOFER

SUB

WOOFER

MONITOR

OUT

SURROUND

CENTER

MAIN

OUT

(REC)

OUTPUTAUDIO

AUDIO OUTPUT

AUDIO INPUT

COAXIAL

OUTPUT

indicates right analog cables

indicates left analog cables

indicates signal direction

CD player

CD recorder or

MD recorder

indicates coaxial cables

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM16

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

TUNER

ANT

GND

75Ω UNBAL.

VIDEO

FREQUENCY

STEP

100kHz/10kHz

FREQUENCY

STEP

50kHz/9kHz

FM/AM

Ground (GND terminal)

For maximum safety and minimum

interference, connect the antenna GND

terminal to a good earth ground. A good

earth ground is a metal stake driven into

moist earth.

Indoor FM

antenna

(included)

AM loop antenna

(included)

Connecting the antennas

■ Connecting the AM loop antenna

1 Set up the AM loop antenna, then connect it.

2 Press and hold the tab to insert the AM loop

antenna lead wires into the AM ANT and

GND terminals.

3 Orient the AM loop antenna for the best

reception.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer

reception than an indoor one. If you experience poor

reception quality, an outdoor antenna may improve the

quality. Consult the nearest authorized YAMAHA

dealer or service center about the outdoor antennas.

FREQUENCY STEP switch (China and General

models)

Because the interstation frequency spacing

differs in different areas, set the

FREQUENCY STEP switch (located on

the rear panel) according to the frequency

spacing in your area.

North, Central and South America:

100 kHz/10 kHz

Other area: 50 kHz/9 kHz

Before setting this switch, disconnect the

AC power plug of this unit from the AC

outlet.

Open the cover of the

included 75-ohm/300-ohm

antenna adapter.

Cut the external sleeve

of the 75-ohm coaxial

cable and prepare it for

connection.

Cut the lead wire and

remove it.

Insert the cable wire into the

slot, and clamp it with pliers.

Snap the cover into

place.

Unit: mm

(inch)

Lead wire

Clamp with

pliers.

Clamp

with

pliers.

Insert the wire

into the slot.

Both AM and FM indoor antennas are included with this

unit. In general, these antennas should provide sufficient

signal strength.

Connect each antenna correctly to the designated

terminals.

75-ohm/300-ohm antenna adapter (U.K. model)

11 (7/16)

8 (5/16)

6 (1/14)

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM17

CONNECTIONS

Connecting an external decoder

This unit is equipped with 6 additional input jacks (MAIN

left and right, CENTER, SURROUND left and right and

SUBWOOFER) for discrete multi-channel input from an

external decoder, sound processor, or pre-amplifier.

Connect the output jacks on your external decoder to the

6CH INPUT jacks. Be sure to match the left and right

outputs to the left and right input jacks for the main and

surround channels.

Notes

• When you select 6CH INPUT as the input source, this unit

automatically turns off the digital sound field processor, and

you cannot listen to DSP programs.

• When you select 6CH INPUT as the input source, settings of

“1 SPEAKER SET” on the SET MENU do not apply (except

for “1E MAIN Lv”).

VO LTAGE

SELECTOR

SWITCHED

50W MAX. TOTAL

AC OUTLETS

VOLTAGE SELECTOR

(General model)

Connecting the power supply

cords

■ Connecting the AC power cord

Plug in this unit to the wall outlet.

■ AC OUTLETS (SWITCHED)

U.S.A., Canada, China, Europe, Singapore and

General models .............................................. 2 OUTLETS

U.K. and Australia model ................................ 1 OUTLET

Use these outlets to connect the power cords from your

components to this unit. The power to the AC OUTLETS

is controlled by this unit’s STANDBY/ON (or POWER).

These outlets will supply power to any source component

connected to this unit whenever this unit is turned on. The

maximum power (total power consumption of

components) that can be connected to the AC OUTLETS

varies depending on the area which it was purchasing.

China and General models......................................... 50 W

Other models ........................................................... 100 W

■ VOLTAGE SELECTOR

(China and General models)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE

plugging into the AC main supply. Voltages are 110/120/

220/240 V AC, 50/60 Hz.

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM18

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

POWER

6CH INPUTSLEEP

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

PRESET

A/B/C/D/E

STANDBY

/ON

POWER

Remote control

Front panel

Turning on the power

When all connections are complete, turn on the power of

this unit.

1 Press STANDBY/ON (POWER on the remote

control) to turn on the power of this unit.

The level of the main volume, and then the current

DSP program name appear on the front panel display.

2 Turn on the video monitor connected to this

unit.

0103V430_9-19_EN(GB) 1/19/02, 8:03 PM19

Item

1A CENTER

1B MAIN

1C REAR LR

1D BASS

1E MAIN Lv

Description

Sets center speaker availability and size.

Sets main speaker size.

Sets rear L/R speakers availability and size.

Sets the speaker(s) to be used to output low bass signals.

Sets the main speaker level.

Possible settings (default

setting indicated in bold)

LRG/SML/NON

LARGE/SMALL

LRG/SML/NON

SWFR/MAIN/BOTH

Nrm (Normal)/–10 dB

SPEAKER MODE SETTINGS

This unit has 5 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your

configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings

as well as other possible settings.

If the initial settings shown in the following table are not appropriate for your speaker configuration,

see “1 SPEAKER SET” on pages 43-44 to change the settings.

Summary of SPEAKER SET items 1A through 1E

0104V430_20-22_EN(GB) 1/19/02, 8:03 PM20

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

This section explains how to adjust speaker output levels

using the test tone generator. When this adjustment is

complete, the output level heard at the listening position

should be the same from each speaker. This is important

for best performance of the digital sound field processor,

and the various decoders (Dolby Digital, Dolby Pro

Logic, Dolby Pro Logic

and DTS).

Note

• Since this unit cannot enter the test mode while headphones are

connected to this unit, be sure to unplug the headphones from

the PHONES jack when using the test tone.

Using the test tone

Use the test tone to balance the output levels of the

speakers. The adjustment of each speaker output level

should be made at your listening position using the

remote control.

1 Press TEST to output the

test tone.

TEST

BASS

–

TREBLE

–

SET MENU

LEVEL

DSP

+–

STEREO

EFFECT

MUTE

VOLUME

TEST

1,4

ADJUSTING SPEAKER OUTPUT LEVELS

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

Remote control

Front panel

2 Set the BASS and TREBLE controls on the

front panel to the center position and adjust

the volume of this unit so you can hear the

test tone.

The test tone is heard (in order) from the main left

speaker, center speaker, main right speaker, rear right

speaker, rear left speaker, and the subwoofer. The

tone is produced for 2.5 seconds from each speaker.

* Subwoofer test tone is output after the rear left

speaker (LEFT SURROUND).

The front panel display shows which speaker is

outputting the test tone.

Note

• If the test tone cannot be heard, turn down the volume, set this

unit to standby mode and check the speaker connections.

L SUR. R SUR.

CENTER

RIGHT

LEFT

*SUBWOOFER

0104V430_20-22_EN(GB) 1/19/02, 8:03 PM21

ADJUSTING SPEAKER OUTPUT LEVELS

3 Adjust the level of the

effect speakers using +/–

so that it matches the

level of the main

speakers.

While adjusting, the test tone

is heard from the selected

speaker.

Note

• To adjust the level of the main speakers, use VOLUME knob

(or VOLUME h/g on the remote control).

4 When adjustment is

complete, press TEST to

stop the test tone.

Notes

• If “1A CENTER” on the SET MENU is set to NON and the

center speaker is not connected, the center channel sound is

automatically output from the main left and right speakers.

• If “1C REAR LR” on the SET MENU is set to NON, the

output level of the rear left and right speakers cannot be

adjusted in step 3. The test tone will be circulated skipping the

rear right and left speakers.

• If “1D BASS” on the SET MENU is set to MAIN, the test tone

will be circulated skipping the subwoofer.

• It is not necessary to readjust the speaker levels once they are

set (as long as you do not change the speakers). You can enjoy

listening to or watching the input source at the desired volume

simply by adjusting the VOLUME knob (or VOLUME h/g on

the remote control).

• If the output level of the effect speakers (center, rear left, and

rear right) cannot be increased enough to match the level of the

main speakers, set “1E MAIN Lv” on SET MENU to –10 dB

(see page 44). This setting decreases the main speaker output

level to about one-third of the normal level. After you have set

“1E MAIN Lv” on the SET MENU to –10 dB, adjust the levels

for the center and rear speakers again.

DSP

+–

TEST

0104V430_20-22_EN(GB) 1/19/02, 8:03 PM22

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

BASIC PLAYBACK

1 Press STANDBY/ON (POWER on the remote

control) to turn on the power.

2 Turn on the video monitor connected to this

unit.

3 Press INPUT l / h repeatedly (one of the

input selector buttons on the remote control)

to select the input source.

The selected input source name and input mode

appear on the front panel display for a few seconds.

To select the audio source connected to the 6CH

INPUT jacks

(When combining with a video source)

• You need to select the input to which the video source

component is connected before selecting audio source.

Press 6CH INPUT until “6CH INPUT” appears on the

front panel display.

Note

• If “6CH INPUT” is shown on the front panel display, no other

source can be played. To select another input source, first press

6CH INPUT to turn off “6CH INPUT” from the front panel

display.

INPUT

POWER

6CH INPUTSLEEP

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

– PRESET +

A/B/C/D/E

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

SET MENU

LEVEL

DSP

+–

STEREO

EFFECT

MUTE

VOLUME

TEST

/ DTS

SUR.

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

VOLUME

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

353

STANDBY

/ON

POWER

Remote control

Front panel

Selected input source

6CH INPUT

Remote controlFront panel

0105V430_23-28_EN(GB) 1/19/02, 8:04 PM23

BASIC PLAYBACK

4 Start playback or select a broadcast station

on the source component.

Refer to the operation instructions for the

component.

5 Adjust the volume to the desired level.

The volume level is displayed digitally.

Example: –70 dB

Control range: VOLUME MUTE (minimum) to

0 dB (maximum)

The volume level indicator also shows the current

volume level as a bar graph.

If desired, use BASS and TREBLE. These controls

only effect the sound from the main speakers.

Notes

• If you increase or decrease the high-frequency or the low-

frequency sound to an extreme level, the tonal quality from the

center and rear speakers may not match that of the main left

and right speakers.

• If you have connected a recording component to the VCR

OUT, or MD/CD-R OUT jacks, and you notice distortion or

low volume during playback of other components, try turning

the recording component on.

6 Select a DSP program if desired.

Use PROGRAM l / h (DSP program buttons on

the remote control) to select a DSP program. See

pages 29 to 33 for details about DSP programs.

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

VOLUME

BASS

–

TREBLE

–

Front panel

Remote control

■ BGV (background video) function

The BGV function allows you to enjoy video images

from a video source together with sounds from an audio

source. For example, you can enjoy listening to classical

music while having beautiful scenery from a video source

on the video monitor.

Select a source from the video group, then select a source

from the audio group using the input selector buttons on

the remote control. BGV selections cannot be made with

INPUT l / h on the front panel.

■ To mute the sound

1 Press MUTE on the

remote control.

To resume the audio output,

press MUTE again.

• You can also cancel mute by pressing VOLUME h/g, etc.

• During muting, the “MUTE” indicator flashes on the front

panel display.

■ When you have finished using

this unit

1 Press STANDBY/ON (POWER on the remote

control) to set this unit in the standby mode.

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

/ DTS

SUR.

Front panel

Remote control

STANDBY

/ON

POWER

Front panel

Remote control

MUTE

0105V430_23-28_EN(GB) 1/19/02, 8:04 PM24

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

BASIC PLAYBACK

Input modes and indications

This unit comes with a variety input jacks. You can select

the type of input signals you desire.

Each time you turn on the power of this unit, the input

mode is set according to “8 INPUT MODE” setting on

the SET MENU (see page 46 for details).

1 Press INPUT MODE (the input selector

button that you have pressed to select the

input source on the remote control)

repeatedly until the desired input mode is

shown on the front panel display.

AUTO: In this mode, the input signal is selected

automatically as follows:

1) Digital signal

2) Analog signal

DTS: In this mode, only the digital input signal

encoded with DTS is selected, even if

another signal is input at the same time.

ANALOG: In this mode, only the analog input signal is

selected, even if a digital signal is input at

the same time.

Notes

• When AUTO is selected, this unit automatically determines the

type of signal. If this unit detects a Dolby Digital or DTS

signal, the decoder automatically switches to the appropriate

setting.

• When playing a disc encoded with Dolby Digital or DTS on

some LD or DVD players, the sound output delays for a

moment when playback resumes after a search because the

digital signal is selected again.

• When playing a LD source that has not been digitally recorded,

the sound may not be output for some LD players. In this case,

set the input mode to ANALOG.

INPUT MODE

DVD AUTO

VOLUME

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

Remote controlFront panel

Input mode

■ Notes on 96-kHz sampling digital

signals

The digital input jacks of this unit can handle 96-kHz

sampling digital signals. Note the following when 96-kHz

sampling digital signal is input to this unit:

– DSP programs cannot be selected.

– Sound will be output as 2-channel stereo from only the

main left and right speakers. (There may be sound

output from the subwoofer depending on the

SPEAKER MODE settings on the SET MENU.)

Therefore, the level of the effect speakers cannot be

adjusted while listening to such a source.

■ Notes on playing DTS-CD/LDs

• If the digital output data of the player has been

processed in any way, you may not be able to perform

DTS decoding even if you make a digital connection

between this unit and the player.

• If you play a source encoded with a DTS signal and

set the input mode to ANALOG, this unit may

reproduce the noise of an unprocessed DTS signal. In

this case, connect the source to a digital input jack and

set the input mode to AUTO or DTS.

• If you switch the input mode to ANALOG while

playing a source encoded with a DTS signal, this unit

reproduces no sound.

• If you play a source encoded with a DTS signal with

the input mode set to AUTO;

– This unit automatically switches to the DTS-

decoding mode (The “t” indicator lights up) after

having detected the DTS signal. When playback of

the DTS source is completed, the “t” indicator

may flash. While this indicator is flashing, only DTS

source can be played. If you want to play a normal

PCM source soon, set the input mode back to AUTO.

– When the input mode is set to AUTO and a search or

skip operation is performed during playback of a

DTS source, the “t” indicator may flash. If this

status continues for longer than 30 seconds, this unit

will automatically switch from “DTS-decoding”

mode to PCM digital signal input mode. The “t”

indicator will turn off.

0105V430_23-28_EN(GB) 1/19/02, 8:04 PM25

BASIC PLAYBACK

Selecting a sound field program

You can enhance your listening experience by selecting a

DSP program. For details about each program, see pages

29 to 33.

1 Press one of the DSP program buttons on

the remote control to select the desired

program.

The name of the selected program appears on the

front panel display.

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

PROGRAM l / h

POWER

6CH INPUTSLEEP

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

– PRESET +

A/B/C/D/E

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

SET MENU

EVE

/ DTS

SUR.

1,2

2 After selecting the desired program, press

the same button repeatedly to select the

desired sub-program if available.

Example: Pressing MOVIE THEATER 1 repeatedly

switches the sub-program between

“Sci-Fi” and “Spectacle”.

Notes

• There are 9 programs with sub-programs available with this

unit. However, the selection depends on the input signal format

and not all sub-programs can be used with all input signal

formats.

• The digital sound field processor cannot be used when a source

connected to the 6CH INPUT jacks of this unit is selected or

when 96-kHz sampling digital signals are input to this unit.

• The acoustics of your listening room affect the DSP program.

Minimize the sound reflections in your room to maximize the

effect created by the program.

• When you select an input source, this unit automatically selects

the last DSP program used with that source.

• When you set this unit in the standby mode, the current source

and DSP program are memorized and are automatically

selected when you turn on the power again.

• If a Dolby Digital or DTS signal is input when the input mode

is set to AUTO, the DSP program (No. 7–9) automatically

switches to the appropriate decoding program.

• When a monaural source is being played with PRO LOGIC/

Normal or PRO LOGIC/Enhanced, or PRO LOGIC Movie,

no sound will be heard from the main speakers and the rear

speakers. Sound can only be heard from the center speaker. (If

“1A CENTER” on the SET MENU is set to NON, the center

channel sound is output from the main speakers.)

• You can also select DSP program by pressing PROGRAM

l / h on the front panel.

• Select a program based on your listening preference. Program

names are just for reference.

DGTLz Sci-Fi

LCR

LFE

DSP

DIGITAL

VOLUME

MOVIE

THTR

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

Sub-program name

Program name

DGTL Spectacle

LCR

LFE

DSP

DIGITAL

VOLUME

MOVIE

THTR

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

/ DTS

SUR.

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

/ DTS

SUR.

Program name

Sub-program name

0105V430_23-28_EN(GB) 1/19/02, 8:04 PM26

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

BASIC PLAYBACK

3 Press SELECT repeatedly to select the

decoder; PRO LOGIC or PRO LOGIC

4 After selecting on the decoder (PRO LOGIC

), select the mode appropriate for the

source by pressing q/DTS SUR.

The selection switches as follow;

PRO LOGIC

Movie ↔ PRO LOGIC Music

• You can select PRO LOGIC, PRO LOGIC Movie, and PRO

LOGIC Music by pressing PROGRAM l / h on the front

panel repeatedly.

■ Selecting PRO LOGIC

You can enjoy the 2-channel sources decoded into five

discrete channels by selecting PRO LOGIC

in program

No. 9.

1 Select a 2-channel source and start playback

on the source component.

2 Press q/DTS SUR.

The previously selected sub program appears on the

front panel display.

PRO LOGIC

DSP

PRO LOGIC

VOLUME

PRO

LOGIC

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

/ DTS

SUR.

Remote control

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

/ DTS

SUR.

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

/ DTS

SUR.

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

PROGRAM l / h

POWER

6CH INPUTSLEEP

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

– PRESET +

A/B/C/D/E

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

SET MENU

EVE

/ DTS

SUR.

2,3,4

0105V430_23-28_EN(GB) 1/19/02, 8:04 PM27

BASIC PLAYBACK

■ Playing Dolby Digital Surround

EX or DTS ES software

Press MATRIX 6.1 to turn on the Dolby Digital + Matrix

6.1 or DTS + Matrix 6.1 decoder.

The display changes AUTO → Matrix6.1 → OFF each

time the MATRIX 6.1 button is pressed.

AUTO: This mode automatically switches Dolby

Digital + Matrix 6.1 and DTS + Matrix 6.1

depending on the signal. Virtual rear center

speaker does not work for 5.1 channel

sources.

Matrix6.1: This setting produces 6-channel playback of

the input source using the Matrix 6.1

decoder. The virtual rear center speaker can

be used when playing a 5.1-channel source.

OFF: Virtual rear center speaker does not work in

this setting.

Notes

• The setting becomes AUTO once this unit turns into standby

mode.

• Some Dolby Digital Surround EX or DTS ES software may not

contain the signal that is necessary for this unit to switch to the

Matrix 6.1 decoding mode. To turn on the Matrix 6.1 decoder

when playing such a source, select “Matrix6.1”.

■ Virtual CINEMA DSP

With Virtual CINEMA DSP, you can enjoy all DSP

programs without rear speakers. It creates virtual speakers

to reproduce a natural sound field.

You can listen to virtual CINEMA DSP by setting “1C

REAR LR” in the SET MENU to NON. Sound field

processing changes to VIRTUAL CINEMA DSP

automatically.

Note

• This unit is not set in the virtual CINEMA DSP mode even if

“1C REAR LR” is set to NON in the following cases:

– when the 5ch Stereo, DOLBY DIGITAL Normal, Pro Logic

Normal, Pro Logic , or DTS Normal program is selected;

– when the sound effect is turned off;

– when 6CH INPUT is selected as the input source;

– when 96-kHz sampling digital signals are input to this unit;

– when using the test tone; or

– when connecting the headphones.

MATRIX

6.1

The MATRIX indicator lights up.

STEREO

EFFECT

STEREO

EFFECT

Front panel

Remote control

Spectacle 6.1

DSP

MATRIX

DIGITAL

MOVIE

THTR

VCR

V-AUX

DVD

TUNER

TV/CBL

MD/CD

DSP

+–

■ SILENT CINEMA DSP

You can enjoy a powerful sound field similar to what you

could expert from actual speakers with SILENT

CINEMA DSP. You can listen to SILENT CINEMA DSP

by connecting your headphones to the PHONES jack

while the digital sound field processor is on. Enjoy all the

DSP program using the headphones. The “SILENT”

indicator lights up on the front panel display. (When

sound effects are off, you listen to the source with normal

stereo reproduction.)

Notes

• This feature is not available when 6CH INPUT is selected or

96-kHz sampling digital signals are input to this unit.

• The sound of LFE channel will be mixed and output from the

headphone.

■ Normal stereo reproduction

1 Press STEREO to turn off the sound effect

for normal stereo reproduction.

Press STEREO again to turn the sound effect back

on.

Notes

• If you turn off the sound effects, no sound is output from the

center speaker, rear speakers.

• If you turn off the sound effects while a Dolby Digital or DTS

signal is being output, the dynamic range of the signal is

automatically compressed and the sounds of the center and rear

speaker channels are mixed and output from the main speakers.

• The volume may be greatly reduced when you turn off the

sound effects or if you set “4 D. RANGE” on the SET MENU

to MIN. In this case turn on the sound effect.

• The sound of LFE channel will be directed to the main left and

right or the subwoofer (or both) channels depending on the

setting of “1D BASS” on the SET MENU.

During stereo reproduction, you can display information such as

the type, format and sampling frequency of the signal input from

the components connected to this unit.

(While playing a source)

1 Press d to display the information about the

input signal.

0105V430_23-28_EN(GB) 1/19/02, 8:04 PM28

BASIC

OPERATION

English

INTRODUCTION PREPARATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

DIGITAL SOUND FIELD PROCESSING (DSP)

Understanding sound fields

A sound field is defined as the “characteristic sound reflections of a

particular space.” In concert halls and other music venues, we hear

early reflections and reverberations as well as the direct sound

produced by the artist(s). The variations in the early reflections and

other reverberations among the different music venues is what gives

each venue its special and recognizable sound quality.

YAMAHA sent teams of sound engineers all around the world to

measure the sound reflections of famous concert halls and music

venues, and collect detailed sound field information such as the

direction, strength, range, and delay time of those reflections. Then

we stored this enormous amount of data in the ROM chips of this

unit.

■ Recreating a sound field

Recreating the sound field of a concert hall or an opera house requires localizing the virtual sound sources in your

listening room. The traditional stereo system that uses only two speakers is not capable of recreating a realistic sound

field. YAMAHA’s DSP requires three effect speakers to recreate sound fields based on the measured sound field data.

The processor controls the strength and delay time of the signals output from the three effect speakers to localize the

virtual sound sources and fully encompass the listener.

Hi-Fi DSP programs

The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in

mind that most of these are precise digital recreations of actual acoustic environments.

No.

Program

CONCERT HALL

JAZZ CLUB

ROCK CONCERT

ENTERTAINMENT/

Disco

ENTERTAINMENT/

5ch Stereo

Features

A large round concert hall with a rich surround effect. Pronounced reflections from all directions

emphasize the extension of sounds. The sound field has a great deal of presence, and your virtual

seat is near the center, close to the stage.

This is the sound field at stage front in “The Bottom Line”, a famous New York jazz club, that

seats up to 300 people. Its wide left to right seating arrangement offers a real and vibrant sound.

The ideal program for lively, dynamic rock music. The data for this program was recorded at

LA’s “hottest” rock club. The listener’s virtual seat is at the center-left of the hall.

This program recreates the acoustic environment of a lively disco in the heart of a big city. The

sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate”

sound.

Using this program increases the listening position range. This is a sound field suitable for

background music at parties, etc.

0106V430_29-33_EN(GB) 1/19/02, 8:04 PM29

CINEMA-DSP

Sound design of CINEMA-DSP

Filmmakers intend for the dialog to be located right on the screen, the effect sound a little farther back, the music spread

even farther back, and the surround sound around the listener. Of course, all of these sounds must be synchronized with

the images on the screen.

CINEMA-DSP is an upgraded version of YAMAHA DSP specially designed for movie soundtracks. CINEMA-DSP

integrates the DTS, Dolby Digital, and Dolby Pro Logic surround sound technologies with YAMAHA DSP sound field

programs to provide a surround sound field. It recreates comprehensive movie sound design in your audio room. In

CINEMA-DSP sound field programs, YAMAHA’s exclusive DSP processing is added to the Main left and right, and

Center channels, so the listener can enjoy realistic dialogue, depth of sound, smooth transition between sound sources,

and a surround sound field that goes beyond the screen.

When a DTS or Dolby Digital signal is detected, the CINEMA-DSP sound field processor automatically chooses the

most suitable sound field program for that signal.

L SURROUND SOUND FIELD

R SURROUND SOUND FIELD

PRESENCE SOUND FIELD

DIALOG

EFFECT MUSIC

In addition to the DSP, this unit is equipped with a variety of precise decoders; Dolby Pro Logic decoder for Dolby

Surround sources, Dolby Pro Logic

decoder for Dolby Surround and 2-channel sources, Dolby Digital/DTS decoder

for multi-channel sources and Dolby Digital + Matrix 6.1 or DTS + Matrix 6.1 decoder for adding a rear center channel

(the rear center channel is outputted from virtual rear center speaker). You can select CINEMA-DSP programs to

optimize these decoders and the DSP sound patterns depending on the input source.

0106V430_29-33_EN(GB) 1/19/02, 8:04 PM30

English

INTRODUCTION PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CINEMA-DSP

The 6-channel soundtracks found on 70-mm film produce precise sound field localization and rich, deep sound without

using matrix processing. This unit’s MOVIE THEATER programs provide the same quality of sound and sound

localization that 6-channel soundtracks do. The built-in Dolby Digital or DTS decoder brings the professional-quality

sound designed for movie theaters into your home. With this unit’s MOVIE THEATER programs, you can use Dolby

Digital or DTS technology to recreate a dynamic sound that gives you the feeling of being in a public theater.

■ Dolby Digital/DTS + DSP sound field effect

These programs use YAMAHA’s tri-field DSP processing

on each of the Dolby Digital or DTS signals for the front,

left surround, and right surround channels. This

processing enables this unit to reproduce the immense

sound field and surround expression of a Dolby Digital-

or DTS-equipped movie theater without sacrificing the

clear separation of all channels.

■ Dolby Digital/DTS + Matrix 6.1 + DSP sound field effect

These programs provide you with the maximum experience of the spacious surround effects by adding an extra rear

center DSP sound field created from the virtual rear center speaker.

■ Dolby Pro Logic + DSP sound field effect

Most movie software has 4-channel (left, center, right,

and surround) sound information encoded by Dolby

Surround matrix processing and stored on the left and

right tracks. These signals are processed by the Dolby Pro

Logic decoder. The MOVIE THEATER programs are

designed to recreate the spaciousness and delicate

nuances of sound that tend to be lost in the encoding and

decoding processes.

■ Dolby Pro Logic

Dolby Pro Logic decodes Dolby Surround software into 5 discrete full-range channels (3 channels in front and 2

channels in rear). There are 2 modes; MOVIE for movies and MUSIC for 2-channel audio sources.

Surround DSP

sound field

Right surround DSP

sound field

Presence DSP

sound field

Left surround DSP

sound field

Presence DSP

sound field

0106V430_29-33_EN(GB) 1/19/02, 8:05 PM31

CINEMA-DSP

CINEMA-DSP programs

■ For movie programs: No. 7 to 9

This unit automatically chooses the appropriate decoder and DSP sound field pattern according to the input signal

format.

Table of Program Names for Each Input Format

MOVIE

THEATER 1

MOVIE

THEATER 2

DOLBY

DIGITAL

DTS DIGITAL

SUR

PRO LOGIC

2 channel

Stereo

70 mm Spectacle

70 mm Sci-Fi

70 mm Adventure

70 mm General

—

Normal

Enhanced

Movie

Music

DOLBY DIGITAL

DGTL Spectacle

DGTL Sci-Fi

DGTL Adventure

DGTL General

Normal

Enhanced

—

5.1 channel

DTS

DTS Spectacle

DTS Sci-Fi

DTS Adventure

DTS General

—

Normal

Enhanced

—

DTS

Matrix 6.1

Spectacle 6.1

Sci-Fi 6.1

Adventure 6.1

General 6.1

—

Matrix 6.1

Enhanced 6.1

—

6.1 channel *

Input

Program

DOLBY DIGITAL

Matrix 6.1

Spectacle 6.1

Sci-Fi 6.1

Adventure 6.1

General 6.1

Matrix 6.1

Enhanced 6.1

—

* means the Matrix 6.1 decoder is ON.

• If a Dolby Digital signal or DTS signal is input when the input mode is set to AUTO, the DSP program will automatically switch to

the Dolby Digital playback sound field or DTS playback sound field.

• If Dolby Digital Surround EX software or DTS ES software is played when AUTO is selected by pressing the MATRIX 6.1 button

on the remote control, the Dolby Digital + Matrix 6.1 or DTS + Matrix 6.1 decoder usually turns on and the corresponding DSP

program is selected.

• MATRIX 6.1 on the remote control can be used to play Dolby Digital or DTS 5.1 channel sources with the virtual rear center

speaker. In this case the program name changes to the corresponding name for 6.1 channel.

• When playing a 6.1 channel source with MATRIX 6.1 on the remote control turned off, the program name changes to the

corresponding name for 5.1 channel.

Notes

• The “ ” indicator does not light up when selecting program No. 9 except in Enhanced mode.

• When playing a monaural source with a CINEMA DSP program, the source signal is directed to the center channel, main and rear

speakers output effect sounds.

No.

0106V430_29-33_EN(GB) 1/19/02, 8:05 PM32

English

INTRODUCTION PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CINEMA-DSP

Program

Enhanced Mode

No.

Program

ENTERTAINMENT/

Game

ENTERTAINMENT/

Concert Video

TV SPORTS

MONO MOVIE

Features

This program adds a deep and spatial feeling to video game sounds.

This program adds a deep and spatial feeling to concert video sounds.

With this program, you can enjoy watching various TV programs such as news, variety shows,

music programs or sports programs. In a stereo broadcast of a sports game, the commentator is

oriented at the center position, and the shouts and the atmosphere in the stadium spread on the

surround side, while their spread to the rear is properly restrained.

This program is provided for reproducing monaural video sources (such as old movies). The

program produces the optimum reverberation to create sound depth by using only the presence

sound field.

■ For audio-video sources: No. 4 to 6

The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in

mind that most of these are precise digital recreations of actual acoustic environments. Select the DSP program that you

feel sounds best regardless of the name and description given for it below.

No.

Features

This program creates the extremely wide sound field of a 70-mm movie theater. It

precisely reproduces the source sound in detail, making both the video and the sound

field incredibly real. This is ideal for any kind of video source encoded with Dolby

Surround, Dolby Digital or DTS (especially large-scale movie productions).

This program clearly reproduces dialog and sound effects in the latest sound form of

science fiction films, thus creating a broad and expansive cinematic space amid the

silence. You can enjoy science fiction films in a virtual-space sound field that includes

Dolby Surround, Dolby Digital and DTS-encoded software employing the most advanced

techniques.

This program is ideal for precisely reproducing the sound design of the newest 70-mm

and multichannel soundtrack films. The sound field is made to be similar to that of the

newest movie theaters, so the reverberations of the sound field itself are restrained as

much as possible.

This program is for reproducing sounds from 70-mm and multichannel soundtrack films,

and is characterized by a soft and extensive sound field. The presence sound field is

relatively narrow. It spatially spreads all around and toward the screen, restraining the

echo effect of conversations without losing clarity.

This program ideally simulates the multi-surround speaker systems of the 35-mm film

theaters. Dolby Pro Logic decoding, Dolby Digital decoding or DTS decoding and digital

sound field processing create precise effects without altering the original sound

orientation.

The surround effects produced by this sound field wrap around the viewer naturally from

the back to the left and right, and toward the screen.

MOVIE

THEATER 1

MOVIE

THEATER 2

Spectacle

Sci-Fi

Adventure

General

0106V430_29-33_EN(GB) 1/19/02, 8:05 PM33

TUNING

4 Press PRESET/TUNING l / h once to begin

automatic tuning.

Press h to tune in to a higher frequency, or press l

to tune in to a lower frequency.

When tuned in to a station, the “TUNED” indicator

lights up and the frequency of the received station is

shown on the front panel display.

• Use the manual tuning method if the tuning search does not

stop at the desired station because the signal is weak.

■ Manual tuning

If the signal from the station you want to select is weak,

you must tune in to it manually.

1 Select TUNER and the reception band

following steps 1 and 2 described in

“Automatic tuning” at left.

2 Press TUNING MODE (AUTO/MAN’L MONO)

so that the “AUTO” indicator goes off from

the front panel display.

If the colon (:) appears on the front panel display,

press PRESET/TUNING (EDIT) to turn it off.

3 Press PRESET/TUNING l / h to tune in to

the desired station manually.

Hold down the button to

continue the tuning search.

Note

• Manually tuning in to an FM station will automatically change

the reception mode to monaural to increase the signal quality.

Automatic and manual tuning

There are 2 ways to tune; automatic and manual.

Automatic tuning is effective when station signals are

strong and there is no interference.

■ Automatic tuning

1 Press INPUT l / h (TUNER on the remote

control) to select TUNER as the input source.

2 Press FM/AM to select the reception band.

“FM” or “AM” appears on the front panel display.

3 Press TUNING MODE (AUTO/MAN’L MONO)

so that the “AUTO” indicator lights up on the

front panel display.

If the colon (:) appears on the front panel display,

press PRESET/TUNING (EDIT) to turn it off.

INPUT

PRESET

TUNING

233

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

FM/AM

AUTO/MAN'L MONO

TUNING MODE

AUTO

Lights up

EDIT

PRESET/TUNING

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

– PRESET +

A/B/C/D/E

Front panel

Remote control

AUTO/MAN'L MONO

TUNING MODE

AUTO

Goes off

EDIT

PRESET/TUNING

PRESET

TUNING

A AM 144O

TUNED

VCR

V-AUX

DVD

TUNER

TV/CBL

MD/CD

A AM 144O

TUNED

VCR

V-AUX

DVD

TUNER

TV/CBL

MD/CD

A AM 144O

TUNED

VCR

V-AUX

DVD

TUNER

TV/CBL

MD/CD

0107V430_34-41_EN(GB) 1/19/02, 8:05 PM34

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TUNING

Presetting stations

■ Automatically presetting stations

(for FM stations)

You can use the automatic preset tuning feature to store

FM stations. This function enables this unit to

automatically tune in to FM stations with strong signals,

and to store up to 40 (8 stations x 5 groups) of those

stations in order. This feature enables you to easily tune in

to any preset station by selecting the preset station

number (see page 37).

1 Press FM/AM to select the FM band.

2 Press TUNING MODE (AUTO/MAN’L MONO)

so that the “AUTO” indicator lights up on the

front panel display.

3 Press and hold MEMORY (MAN’L/AUTO FM)

for more than 3 seconds.

The preset number and the “MEMORY” and

“AUTO” indicators flash. Then, after about

5 seconds, automatic preset tuning begins from the

frequency currently displayed toward the higher

frequencies.

When automatic preset tuning is completed, the front

panel display shows the frequency of the last preset

station.

AUTO/MAN'L MONO

TUNING MODE

MEMORY

MAN'L/AUTO FM

AUTO

A1:FM

MEMORY

AUTO

VOLUME

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

Lights up

Notes

• Any stored station data existing under a preset number is

cleared when you store a new station under that preset number.

• When a station data is stored under a preset number, the

frequency and reception band are also stored.

• You can manually replace a preset station with another FM or

AM station by simply following the procedure in the section

“Manually presetting stations” on page 36.

• If the number of the received stations does not reach E8,

automatic preset tuning has automatically stopped after

searching all stations.

• Only FM stations with sufficient signal strength are stored

automatically by automatic preset tuning. If the station you

want to store is weak in signal strength, tune in to it manually

in the monaural mode, and store it by following the procedure

in “Manually presetting stations” on page 36.

Automatic preset tuning options

You can select the preset number from which this unit

will store FM stations and/or begin tuning toward lower

frequencies. After pressing MEMORY in step 3:

1. Press A/B/C/D/E and PRESET/TUNING l / h to

select the preset number under which the first station

will be stored. Automatic preset tuning will stop when

stations have all been stored up to E8.

2. Press PRESET/TUNING (EDIT) to turn off the colon

(:) and then press PRESET/TUNING l to begin

tuning toward lower frequencies.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is set in the standby

mode, the power cord is disconnected from the AC

outlet, or the power supply is temporarily cut due to

power failure. However, if the power is cut for more

than one week, the preset stations may be cleared. If

so, store the stations again.

FM/AM

0107V430_34-41_EN(GB) 1/19/02, 8:05 PM35

TUNING

■ Manually presetting stations

You can also store up to 40 stations (8 stations x 5

groups) manually.

1 Tune in to a station.

See page 34 for tuning instructions.

When tuned in to a station, the front panel display

shows the frequency of received station.

2 Press MEMORY (MAN’L/AUTO FM).

The “MEMORY” indicator flashes for about

5 seconds.

3 Press A/B/C/D/E repeatedly to select a preset

station group (A to E) while the “MEMORY”

indicator is flashing.

The group letter appears and make sure that the

colon (:) appears on the front panel display.

MEMORY

MAN'L/AUTO FM

MEMORY

A/B/C/D/E

C :AM 63O kHz

TUNED

MEMORY

VOLUME

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

32,5

Shows the displayed station has been stored as C3.

Flashes

4 Press PRESET/TUNING l / h to select a

preset station number (1 to 8) while the

“MEMORY” indicator is flashing.

Press h to select a higher preset station number.

Press l to select a lower preset station number.

5 Press MEMORY (MAN’L/AUTO FM) on the

front panel while the “MEMORY” indicator is

flashing.

The station band and

frequency appear on the front

panel display with the preset

group and number you have

selected.

6 Repeat steps 1 to 5 to store other stations.

Notes

• Any stored station data existing under a preset number is

cleared when you store a new station under that preset number.

• The reception mode (stereo or monaural) is stored along with

the station frequency.

A AM 63O kHz

TUNED

VOLUME

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

PRESET

TUNING

C3:AM 63O kHz

TUNED

MEMORY

VOLUME

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

MEMORY

MAN'L/AUTO FM

C3:AM 63O kHz

TUNED

VOLUME

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

0107V430_34-41_EN(GB) 1/19/02, 8:05 PM36

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TUNING

Exchanging preset stations

You can exchange the assignment of two preset stations.

The example below describes the procedure for

exchanging preset station “E1” with “A5”.

1 Tune in to preset station “E1” by using the

A/B/C/D/E and PRESET/TUNING l / h.

See “Tuning in to a preset station” at left.

2 Press and hold PRESET/TUNING (EDIT) for

more than 3 seconds.

“E1” and the “MEMORY” indicator flash on the

front panel display.

3 Tune in to preset station “A5” by using the

A/B/C/D/E and PRESET/TUNING l / h.

“A5” and the “MEMORY” indicator flash on the

front panel display.

4 Press PRESET/TUNING (EDIT) again.

The stations stored at the two preset assignments are

exchanged.

Tuning in to a preset station

You can tune any desired station simply by selecting the

preset station number under which it was stored.

1 Press A/B/C/D/E (A/B/C/D/E on the remote

control) to select the preset station group.

The preset group letter appears on the front panel

display and changes each time you press A/B/C/D/E.

2 Press PRESET/TUNING l / h (PRESET +/–

on the remote control) to select a preset

station number (1 to 8).

The preset group and number appear on the front

panel display along with the station band, frequency

and the “TUNED” indicator lights up.

EDIT

PRESET/TUNING

PRESET

+–

PRESET

TUNING

A/B/C/D/E

A5:FM 9O.6 MHz

TUNED

MEMORY

VOLUME

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

EDIT E1-A5

MEMORY

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

Shows the exchange of stations has

been completed.

Front panel

Remote control

Front panel

Remote control

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

– PRESET +

A/B/C/D/E

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

/ DTS

SUR.

2,4 1,3 1,3

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

STANDBY

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

EDIT

PRESET/TUNING

E1:FM 87.5 MHz

TUNED

MEMORY

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

E1:FM 87.5 MHz

TUNED

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

0107V430_34-41_EN(GB) 1/19/02, 8:05 PM37

Description of RDS data

This unit can receive, PS, PTY, RT, CT, and EON data

when receiving RDS broadcasting stations.

■ PS (Program Service name)

mode:

The name of the RDS station being received is displayed.

■ PTY (Program Type) mode:

There are 15 program types to classify RDS stations.

■ RT (Radio Text) mode:

Information about the program (such as the title of the

song, name of the singer, etc.) on the RDS station being

received is displayed by a maximum of 64 alphanumeric

characters, including the umlaut symbol. If other

characters are used for RT data, they are displayed with

under-bars.

■ CT (Clock Time) mode:

The current time is displayed and updated every minute.

If the data are accidentally cut off, “CT WAIT” may

appear.

■ EON (Enhanced Other Networks):

Refer to following page.

Changing the RDS mode

The four modes are available in this unit for displaying

RDS data. When an RDS station is being received, PS,

PTY, RT and/or CT mode indicators that correspond to

the RDS data services offered by the station light up on

the front panel display. Press RDS MODE/FREQ

repeatedly to change the display mode among the RDS

data offered by the transmitting station in the order shown

below.

Notes

• When an RDS station is being received, do not press RDS

MODE/FREQ until one or more RDS mode indicators light up

on the front panel display. If you press the button before the

indicators light up on the front panel display, the mode cannot

be changed. This is because this unit has not yet received all of

the RDS data on the station.

• RDS data not offered by the station cannot be selected.

• The RDS data service cannot be utilized by this unit if the

received signal is not strong enough. In particular, the RT mode

requires a large amount of data to be received, so it is possible

that the RT mode may not be displayed even if other RDS

modes (PS, PTY, etc.) are displayed.

• RDS data cannot sometimes be received under poor reception

conditions. If so, press TUNING MODE so that the “AUTO”

indicator goes off from the front panel display. Although the

reception mode is changed to monaural by this operation, when

you change the display to RDS mode, RDS data may be

displayed.

• If the signal strength is weakened by external interference

during the reception of an RDS station, the RDS data service

may be cut off suddenly and “...WAIT” will appear on the front

panel display.

PS mode

RDS mode

OFF

CT mode

RT mode

PTY mode

NEWS

AFFAIRS

INFO

SPORT

EDUCATE

DRAMA

CULTURE

SCIENCE

VARIED

POP M

ROCK M

M.O.R. M

LIGHT M

CLASSICS

OTHER M

News

Current affairs

General information

Sports

Education

Drama

Culture

Science

Light entertainment

Pops

Rock

Middle-of-the-road music

(easy-listening)

Light classics

Serious classics

Other music

RDS MODE/FREQ

EON

RECEIVING RDS STATIONS

RDS (Radio Data System) is a data transmission system by FM stations in many countries.

RDS data contains various information such as PS (Program Service name), PTY (Program Type), RT (Radio Text), CT

(Clock Time), EON (Enhanced Other Networks), etc. The RDS function is carried out among the network stations.

0107V430_34-41_EN(GB) 1/19/02, 8:05 PM38

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

RECEIVING RDS STATIONS

PTY SEEK function

If you select the desired program type, this unit

automatically searches all preset RDS stations that are

broadcasting a program of the required type.

1 Press PTY SEEK MODE to set this unit in the

PTY SEEK mode.

The program type of the station being received or

“NEWS” flashes on the front panel display.

2 Press PRESET/TUNING l / h to select the

desired program type.

The selected program type appears on the front panel

display.

3 Press PTY SEEK START to begin searching

all preset RDS stations.

The selected program type flashes and the “PTY

HOLD” indicator lights up on the front panel display

while searching for stations.

• If a station that is broadcasting a program of the

required type is found, this unit stops at that

station.

• If the called station is not the desired one, press

PTY SEEK START again. This unit begins

searching for another station that is broadcasting a

program of the same type.

■ To cancel this function

Press PTY SEEK MODE twice.

PTY SEEK

MODE

START

EON function

This function uses the EON data service on the RDS

station network. If you simply select the desired program

type (NEWS, INFO, AFFAIRS or SPORT), this unit

automatically searches for all preset RDS stations that are

scheduled to broadcast a program of the required type and

switches from the station being currently received to the

new station when the broadcasts starts.

Note

• This function can only be used when an RDS station that offers

the EON data service is being received. When such a station is

being received, the “EON” indicator lights up on the front

panel display.

1 Make sure that the “EON” indicator lights up

on the front panel display.

If the “EON” indicator does not light up, tune in to

another RDS station so that the “EON” indicator

lights up.

2 Press EON repeatedly to select the desired

program type (NEWS, INFO, AFFAIRS or

SPORT).

The selected program type name appears on the front

panel display.

• If a preset RDS station of the selected program

type starts broadcasting, this unit will

automatically switch from the program being

currently received to that program. (EON indicator

flashes.)

• When broadcasting of the required program ends,

the previously received station (or another

program on the same station) is recalled.

■ To cancel this function

Press EON repeatedly until no program type name lights

up on the front panel display.

PTY SEEK

MODE

START

RDS MODE/FREQ

EON

Flashes

Lights up

PRESET

TUNING

PTY HOLD

0107V430_34-41_EN(GB) 1/19/02, 8:05 PM39

Use this feature to automatically set this unit in the

standby mode after the amount of time you have set. The

sleep timer is useful when you are going to sleep while

this unit is playing or recording a source. The sleep timer

also automatically turns off the external component(s)

connected to AC OUTLET(S).

The sleep timer can only be set with the remote control.

• By connecting a commercially available timer to this unit, you

can also set a wake-up timer. Refer to the operation instructions

of the timer.

Setting the sleep timer

1 Select a source and start playback on the

source component.

2 Press SLEEP repeatedly

to set the amount of time.

Each time you press SLEEP,

the front panel display changes

as shown below.

3 The “SLEEP” indicator lights up on the front

panel display soon after the sleep timer has

been set.

The display then returns to the previous indication.

SLEEP

POWER

6CH INPUTSLEEP

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

– PRESET +

A/B/C/D/E

SLEEP 12Omin

DSP

PCM

SLEEP

VOLUME

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

CONCERT HALL

DSP

PCM

SLEEP

VOLUME

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

SLEEP TIMER

Canceling the sleep timer

1 Press SLEEP repeatedly until “SLEEP OFF”

appears on the front panel display.

After a few seconds, “SLEEP OFF” disappears, the

“SLEEP” indicator goes off and the display returns

to the previous indication.

• The sleep timer setting can also be canceled by setting this unit

in the standby mode by using POWER on the remote control

(or STANDBY/ON on the front panel) or by disconnecting the

AC power cord from the AC outlet.

0107V430_34-41_EN(GB) 1/19/02, 8:05 PM40

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

INPUT

POWER

6CH INPUTSLEEP

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

– PRESET +

A/B/C/D/E

DVD D-TV/CBL VCR

V-AUX

CD TUNER MD/CD-R

Front panel Remote control

RECORDING

Notes

• Do a test recording before you start an actual recording.

• When this unit is set in the standby mode, you cannot record

between the components connected to this unit.

• The setting of BASS, TREBLE, VOLUME, “5 L/R

BALANCE” on the SET MENU and DSP programs does not

effect the recorded material.

• A source connected to the 6CH INPUT jacks on this unit

cannot be recorded.

• A given input source is not output to the same OUT (REC)

channel. (For example, the signal input from VCR IN is not

output to VCR OUT.)

• Check the copyright laws in your country to record from

records, CDs, radio, etc. Recording of copyrighted material

may infringe copyright laws.

If you playback a video source that uses scrambled or

encoded signals to prevent it from being dubbed, the

picture itself may be disturbed due to those signals.

■ Special considerations when

recording DTS software

The DTS signal is a digital bitstream. Attempting to

digitally record the DTS bitstream will result in noise

being recorded. Therefore, if you want to use this unit to

record sources that have DTS signals recorded on them,

the following considerations and adjustments need to be

made.

For LDs, DVDs and CDs encoded with DTS, when your

player is compatible with the DTS format, follow its

operation instruction to make a setting so that the analog

signal will be output from the player.

■ Timer playback/recording

This unit can perform playback or recording with an

external timer (not supplied). Refer to the operating

instructions for the component and the timer to be used.

Notes

• Stored data, such as input source, will be reflected when

playback or recording with the timer.

• If you do not want any sound output when recording with a

timer, turn the volume down.

Memory back-up

The memory back-up circuit prevents the stored data

(input source, volume level, set menu settings and so

on) from being lost even if this unit is disconnected

from the AC outlet. However, if the timer is turned off

for more than one week, the stored data will be lost.

NATURAL SOUND AV RECEIVER

SILENT

PHONES

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

INPUT

INPUT M0DE

6CH INPUT

VOLUME

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

STANDBY

Recording adjustments and other operations are

performed from the recording components. Refer to the

operation instructions for these components.

1 Turn on the power of this unit and all

connected component.

2 Select the source component you want to

record from.

3 Start playback (or select a broadcast station)

on the source component.

4 Start recording on the recording component.

0107V430_34-41_EN(GB) 1/19/02, 8:05 PM41

DSP

+–

Adjusting the items on the SET

Adjustment should be made with the remote control.

Note

• Some items require extra steps.

1 Press SET MENU to enter

the SET MENU.

2 Press u/d repeatedly to

select the item you want

to adjust (1 to 10).

• By pressing SET MENU repeatedly, you can select items in the

same order as when pressing d.

3 Press +/– once to enter

the setup mode of the

selected item.

The last setting you adjusted

appears on the front panel

display.

Depending on the item, press

u/d to select a sub item.

SET MENU

ADVANCED OPERATION

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

SET MENU

LEVEL

DSP

+–

STEREO

EFFECT

TEST

/ DTS

SUR.

2,5

The SET MENU consists of 10 items including the

speaker mode setting. Choose the appropriate item and

adjust or select the values as necessary.

• You can adjust the items on the SET MENU while playing a

source.

Items Initial settings

1 SPEAKER SET

A CENTER LRG (large)

B MAIN LARGE

C REAR LR LRG (large)

D BASS BOTH

E MAIN Lv Nrm (Normal)

2 LFE LEVEL SP/HP 0 dB

3 SP DLY TIME 0 ms

4 D. RANGE SP/HP MAX

5 L/R BALANCE 0 dB for L/R

HP TONE CTRL BASS/TRBL

0 dB

7 I/O ASSIGN

C (optical input) (1) DVD

D (coaxial input) (2) CD

8 INPUT MODE AUTO

9 DISPLAY SET

DIMMER 0

10 MEM. GUARD OFF

• In the descriptions for each item from the following page, the

default setting is indicated in bold.

SET MENU

DSP

+–

DSP

+–

0108V430_42-46_EN(GB) 1/19/02, 8:05 PM42

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SET MENU

4 Press +/– repeatedly to

change the setting of the

item.

5 Press u/d repeatedly until the menu

disappears or simply press one of the DSP

program group buttons to exit SET MENU.

DSP

+–

DSP

+–

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

/ DTS

SUR.

1 SPEAKER SET (speaker mode

settings)

Use this feature to select suitable output modes for your

speaker configuration.

Notes

• When 96-kHz sampling digital signals are input to this unit,

some items are not affected.

• When 6CH INPUT is selected as the input source, level

adjustments in items 1A through 1D are not affected.

■ 1A CENTER (center speaker

mode)

By adding a center speaker to your speaker configuration,

this unit can provide better dialog localization for several

listeners and superior synchronization of sound and

images.

Choices: LRG (large), SML (small), NON (none)

LRG

Select this if you have a large center speaker. The entire

range of the center channel signal is directed to the center

speaker.

SML

Select this if you have a small center speaker. The low-

frequency signals (90 Hz and below) of the center

channel are directed to the speakers selected with “1D

BASS”.

NON

Select this if you do not have a center speaker. All of the

center channel signal are directed to the main left and

right speakers.

■ 1B MAIN (main speaker mode)

Choices: LARGE, SMALL

LARGE

Select this if you have large main speakers. The entire

range of the main left and right channel signal is directed

to the main left and right speakers.

SMALL

Select this if you have small main speakers. The low-

frequency signals (90 Hz and below) of the main channel

are directed to the speakers selected with “1D BASS”.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is in the standby

mode. However, if the power cord is disconnected

from the AC outlet, or the power supply is cut for

more than one week, the stored data will be lost. If so,

adjust the items again.

0108V430_42-46_EN(GB) 1/19/02, 8:05 PM43

SET MENU

■ 1C REAR LR (rear speaker mode)

Choices: LRG (large), SML (small), NON (none)

LRG

Select this if you have large rear left and right speakers or

if a rear subwoofer is connected to the rear speakers. The

entire range of the rear channel signal is directed to the

rear left and right speakers.

SML

Select this if you have small rear left and right speakers.

The low-frequency signals (90 Hz and below) of the rear

channel are directed to the speakers selected with “1D

BASS”.

NON

Select this if you do not have rear speakers.

• This unit is set in the virtual CINEMA DSP mode when you

select NON for “1C REAR LR”.

■ 1D BASS (LFE/bass out mode)

LFE signals carry low-frequency effects when this unit

decodes a Dolby Digital or DTS signal. Low-frequency

signals are defined as 90 Hz and below. The Low-

frequency signals can be directed to both main left and

right speakers, and the subwoofer (subwoofer can be used

for both stereo reproduction and the DSP program).

Choices: SWFR (subwoofer), MAIN, BOTH

SWFR

Select this if you use a subwoofer. The LFE signals are

directed to the subwoofer.

MAIN

Select this if you do not use a subwoofer. The LFE

signals are directed to the main speakers.

BOTH

The LFE signals are directed to the subwoofer. Low-

frequency signals designated to the main channels in

accordance with other speaker mode settings are directed

to both main speakers and a subwoofer.

Note

• When you select MAIN for “1D BASS”, the low-frequency

signals (90 Hz and below) of the main channel are directed to

the main speakers even if you select SMALL for the main

speaker mode.

■ 1E MAIN Lv (main level mode)

Change this setting if you cannot match the output level

of the center, and rear (L/R) speakers with the main

speakers because of unusually high-efficiency

performance from the main speakers.

Choices: Nrm (Normal), –10 dB

Nrm

Select this if you can match the output level of your effect

speakers with that of your main speakers when using the

test tone.

–10 dB

Select this if you cannot match the output level of your

effect speakers with that of your main speakers when

using the test tone.

2 LFE LEVEL

Use this feature to adjust the output level of the LFE

(low-frequency effect) channel when playing back a

Dolby Digital or DTS signal. The LFE signal carries the

low-frequency special effect sound which is only added to

certain scenes.

Control range:

SPEAKER ............ –20 to 0 dB

HEADPHONE ..... –20 to 0 dB

Initial setting: 0 dB

1 Press d/u to select the item to be adjusted.

2 Press – to adjust the LFE level.

Note

• Adjust the LFE level according to the capacity of your

subwoofer or headphones.

0108V430_42-46_EN(GB) 1/19/02, 8:05 PM44

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SET MENU

3 SP DLY TIME (speaker delay

time)

Use this feature to adjust the delay of the center channel

sounds. This feature works when there is sound output

from the center speaker, with a source like Dolby Digital

or DTS, etc. Ideally, the center speaker should be the

same distance from the main listening position as the left

and right speakers. However, in most home situations, the

center speaker is placed in line with the main speakers.

By delaying the sound from the center speaker, the

apparent distance from the center speaker to the main

listening position can be adjusted to make it seem the

same as the distance between the main left and right

speaker to the listening position. Adjusting the delay time

for the center speaker is especially important for giving

depth to the dialogue.

Control range:

CENTER .......................... 0 to 5 ms

Initial setting:

CENTER .......................... 0 ms

1 Press +/– to increase or decrease the delay

of the center channel sounds.

Center speaker image

• Increasing the delay by 1 ms simulates moving the speakers

about 30 cm (one foot) farther away from the listening

position.

4 D. RANGE (dynamic range)

Use this feature to adjust the dynamic range. This setting

is effective only when this unit is decoding Dolby Digital

signals.

Choices: MAX, STD (standard), MIN (minimum)

MAX

Select the “MAX” for feature films.

STD

Select the “STD” for general use.

MIN

Select the “MIN” for listening to sources at low volume

levels.

5 L/R BALANCE (balance of the

main left and right speakers)

Use this feature to adjust the balance of the output level

from the main left and right speakers.

Control range: 20 steps for L/R

Initial setting: 0 dB for L/R

1 Press + to decrease the output level for the

main left speaker. Press – for the main right

speaker.

6 HP TONE CTRL (headphone tone

control)

Use this feature to adjust the level of the bass and treble

when you use your headphones.

Control range (dB):

BASS ............... –6 to +3

TRBL (treble) .. –6 to +3

Initial setting:

BASS ............... 0 dB

TRBL ............... 0 dB

0108V430_42-46_EN(GB) 1/19/02, 8:05 PM45

SET MENU

9 DISPLAY SET

■ DIMMER

You can adjust the brightness of the front panel display.

Control range: –4 to 0

Initial setting: 0

10 MEM. GUARD (memory guard)

Use this feature to prevent accidental changes to settings

on this unit.

Choices: ON, OFF

Select ON to protect the following features:

• All SET MENU items

• Center, rear speakers, and subwoofer levels

• DSP program parameters

Notes

• When this item is set to ON, you cannot use the test tone.

• When this item is set to ON, you cannot select any other SET

MENU items.

7 I/O ASSIGN (input/output

assignment)

It is possible to assign jacks according to the component

to be used if this unit’s DIGITAL INPUT jack settings

(component names for jacks) differ from that component.

This makes it possible to change the jack assignment and

effectively connect more components.

Once you assign, you can select that component with

INPUT l / h (or the input selector buttons on the

remote control).

■ 7C OPTICAL IN for OPTICAL

INPUT jacks

Choices: (1) MD/CD-R, CD, V-AUX, VCR,

D-TV/CBL, DVD

■ 7D COAXIAL IN for COAXIAL

INPUT jack

Choices: (2) MD/CD-R, CD, V-AUX, VCR,

D-TV/CBL, DVD

Notes

• You cannot select an item more than once for the same type of

jack.

• When you connect a component to both the COAXIAL and

OPTICAL jacks, priority is given to the input signals from the

COAXIAL jack.

8 INPUT MODE (initial input

mode)

Use this feature to designate the input mode for sources

connected to the DIGITAL INPUT jacks when you turn

on this unit (see page 25 for details about the input

mode).

Choices: AUTO, LAST

AUTO

Select this to allow this unit to automatically detect the

type of input signal and select the appropriate input mode.

LAST

Select this to set this unit to automatically select the last

input mode used for the respective source.

0108V430_42-46_EN(GB) 1/19/02, 8:05 PM46

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

You can adjust the output level of each effect speaker

(center, rear left and right, and subwoofer) while listening

to a source.

Adjustment should be made with the remote control.

(While playing a source)

1 Press LEVEL repeatedly to select the

speaker(s) you want to adjust.

Each time you press LEVEL, the selected speaker

changes and appears on the front panel display as

follows: center, rear right, rear left and subwoofer.

LEVEL

SET MENU

LEVEL

DSP

+–

STEREO

EFFECT

MUTE

VOLUME

TEST

DSP

+–

DSP

+–

LEVEL

ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS

• Once you press LEVEL, you can also select the speaker(s) to

be adjusted by pressing d / u.

Center speaker output level

Subwoofer output level

Rear left speaker output

level

Rear right speaker output

level

2 Press +/– to adjust the speaker output level.

• The control range for the center or rear left and

right speakers is from +10 dB to –10 dB.

• The control range for the subwoofer is from 0 dB

to –20 dB.

Notes

• When the speaker output modes for “1A CENTER” and “1C

REAR LR” are set to NON, and “1D BASS” to MAIN, the

output level of those speakers cannot be adjusted because there

is no sound coming from these speakers.

• When you adjust the output level with LEVEL, the settings you

made with the test tone will be changed.

• We recommend adjusting the speakers by following the steps

described in “Using the test tone” on pages 21 and 22.

■ For 5ch Stereo

You can adjust the volume level for each channel in 5-

channel stereo mode.

Control range: 0 to 100%

• CT level (Center level)

• RL level (Rear left level)

• RR level (Rear right level)

1 Select 5ch Stereo.

2 Press u / d repeatedly to select the

speaker(s) you want to adjust.

3 Press +/– to adjust the speaker output level.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is in the standby

mode. However, if the power cord is disconnected

from the AC outlet, or the power supply is cut for

more than one week, the stored data will be lost. If so,

set the output level again.

0109V430_47-49_EN(GB) 1/19/02, 8:05 PM47

You can adjust the time difference between the beginning

of the sound from the main speakers and the beginning of

the sound effect from the rear speakers. The larger the

value, the later the sound effect is generated. The delay

time can be individually adjusted to all DSP programs.

The following table shows factory-set delay time.

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

SET MENU

LEVEL

DSP

+–

STEREO

EFFECT

TEST

/ DTS

SUR.

DSP

+–

ADJUSTING THE DELAY TIME

Adjustment should be made with the remote control.

(While playing a source)

1 Select a DSP program you want to adjust the

delay time.

2 Press u / d so that “DELAY” appears on the

front panel display.

3 Press +/– to adjust the delay time.

Notes

• Adding too much delay will cause an unnatural effect with

some sources.

• The sound is momentarily interrupted while adjusting the delay

time.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is in the standby

mode. However, if the power cord is disconnected

from the AC outlet, or the power supply is cut for

more than one week, the stored data will be lost. If so,

adjust the delay time again.

Program

Preset value (ms)

1. CONCERT HALL 45

2. JAZZ CLUB 30

3. ROCK CONCERT 15

4. DISCO 26

GAME 36

CONCERT VIDEO 21

5. TV SPORTS 10

6. MONO MOVIE 69

7. 70 mm SPECTACLE 23

DGTL SPECTACLE 15

DTS SPECTACLE 15

Spectacle 6.1 15

70 mm SCI-FI 20

Sci-Fi 6.1 15

DGTL SCI-FI 15

DTS SCI-FI 15

8. 70 mm ADVENTURE 20

DGTL ADVENTURE 15

DTS ADVENTURE 15

Adventure 6.1 15

70 mm GENERAL 20

DGTL GENERAL 15

DTS GENERAL 15

General 6.1 15

9. PRO LOGIC/NORMAL 15

DOLBY DIGITAL/NORMAL 5

DTS DIGITAL SUR./NORMAL 5

Matrix 6.1 5

PRO LOGIC/ENHANCED 20

DOLBY DIGITAL/ENHANCED 5

DTS DIGITAL SUR./ENHANCED 5

Enhanced 6.1 5

PRO LOGIC Movie 15

PRO LOGIC Music 5

DELAY

0109V430_47-49_EN(GB) 1/19/02, 8:06 PM48

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

Changing parameter settings

You can adjust the values of PRO LOGIC Music

parameters so the sound fields are recreated accurately in

your listening room.

Adjustments should be made with the remote control.

1 Select PRO LOGIC Music.

2 Press u / d to select the

parameter.

3 Press +/– to change the

parameter value.

4 Repeat steps 2 and 3 above as necessary to

change other parameters.

Note

• You cannot change parameter values when “10 MEM.

GUARD” on the SET MENU is set to ON.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is set in the standby

mode, the power cord is disconnected from the AC

outlet, or the power supply is temporarily cut due to

power failure. However, if the power is cut for more

than one week, the parameter value you edited will

return to the factory setting. If so, edit the parameter

value again.

DSP

+–

DSP

+–

SELECT

/ DTS

SUR.

PROGRAM

HALL

JAZZ

CLUB

ROCK

CONCERT

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

1 – THEATER – 2

MATRIX

6.1 SELECT

SET MENU

LEVEL

DSP

+–

STEREO

EFFECT

TEST

/ DTS

SUR.

PRO LOGIC Music parameter

descriptions

■ PANORAMA

Function: Turning the function on extends the front

stereo image to include the surround

speakers for wraparound effect.

Choices: OFF/ON, initial setting is OFF.

■ DIMENSION

Function: Gradually adjusts the soundfield either

towards the front or towards the rear.

Control range: –3 (towards the rear) to +3 (towards the

front), initial setting is STD (standard).

■ CT WIDTH (Center width)

Function: Adjusts the center image from all three

front speakers to varying degrees. The

larger the value, adjusts the center image

towards the main left and right speakers.

Control range: 0 (center channel sound is output only

from center speaker) to 7 (center channel

sound is output only from main left and

right speakers), initial setting is 3.

ADJUSTING THE PARAMETER SETTINGS FOR PRO LOGIC MUSIC

0109V430_47-49_EN(GB) 1/19/02, 8:06 PM49

TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed

below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and

contact the nearest authorized YAMAHA dealer or service center.

■ General

Problem

This unit fails to turn

on when STANDBY/

ON (or POWER) is

pressed, or enters in

the standby mode

soon after the power

has been turned on.

No sound.

Cause

The power cord is not connected or the

plug is not completely inserted.

The IMPEDANCE SELECTOR switch

on the rear panel is not fully set to either

the left or right position.

The protection circuitry has been

activated.

This unit has been exposed to a strong

external electric shock (such as lightning

and strong static electricity).

Incorrect input or output cable

connections.

An appropriate input source has not been

selected.

The speaker connections are not secure.

The volume is turned down.

The sound is muted.

Digital signals which this unit cannot

reproduce are being input to this unit by

playing a CD-ROM, etc.

Remedy

Firmly connect the power cord.

Set the switch fully to the left or right position when

this unit is in the standby mode.

Make sure all speaker wire connections on this unit

and on all speakers are secure and that the wire for

each connection does not touch anything other than

its respective connection.

Set this unit in the standby mode, disconnect the

power cord, plug it back in after 30 seconds, then

start operating.

Connect the cables properly. If the problem persists,

the cables may be defective.

Select an appropriate input source with INPUT

l / h

or 6CH INPUT (or the input selector buttons).

Secure the connections.

Turn up the volume.

Press MUTE or any operation buttons of this unit to

cancel a mute and adjust the volume.

Play a source whose signals this unit can reproduce.

Refer

to page

—

10, 11

—

10 – 16

10, 11

—

0110V430_50-56_EN(GB) 1/19/02, 8:06 PM50

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TROUBLESHOOTING

Problem

The sound suddenly

goes off.

Only the speaker on

one side can be

heard.

No sound from the

effect speakers.

No sound from the

center speaker.

No sound from the

rear speakers.

No sound from the

subwoofer.

Poor bass

reproduction.

Cause

The protection circuit has been activated

because of a short circuit, etc.

The sleep timer has functioned.

The sound is muted.

Incorrect cable connections.

Incorrect setting of “5 L/R BALANCE”

on the SET MENU.

The sound effect is off.

A Dolby Surround, Dolby Digital or

DTS decoding DSP program is being

used with material not encoded with

Dolby Surround, Dolby Digital or DTS.

A 96-kHz sampling digital signal is

being input to this unit.

The output level of the center speaker is

set to minimum.

“1A CENTER” on the SET MENU is set

to NON.

One of the Hi-Fi DSP programs (1 to 4)

has been selected (except for 5ch Stereo).

The source encoded with a Dolby Digital

or DTS signal does not have a center

channel signal.

The output level of the rear speakers is

set to minimum.

A monaural source is being played with

program 9.

“1D BASS” on the SET MENU is set to

MAIN when a Dolby Digital or DTS

signal is being played.

“1D BASS” on the SET MENU is set to

SWFR or MAIN when a 2-channel

source is being played.

The source does not contain low bass

signals (90 Hz and below).

“1D BASS” on the SET MENU is set to

SWFR or BOTH and your system does

not include a subwoofer.

The speaker mode settings (main, center,

or rear) on the SET MENU does not

match your speaker configuration.

Remedy

Check the IMPEDANCE SELECTOR switch is set

to the appropriate position and then turn this unit

back on.

Check the speaker wires are not touching each other

and then turn this unit back on.

Turn on the power, and play the source again.

Press MUTE or any operation buttons of this unit to

cancel a mute and adjust the volume.

Connect the cables properly. If the problem persists,

the cables may be defective.

Adjust it to the appropriate position.

Press STEREO/EFFECT to turn it on.

Select another DSP program.

Raise the level of the center speaker.

Select the appropriate mode for your center speaker.

Select another DSP program.

Raise the output level of the rear speakers.

Select another DSP program.

Select SWFR or BOTH.

Select BOTH.

Select MAIN.

Select the appropriate position for each speaker

based on the size of the speakers in your

configuration.

Refer

to page

—

10, 11

26 – 33

—

26 – 33

—

26 – 33

—

43, 44

0110V430_50-56_EN(GB) 1/19/02, 8:06 PM51

TROUBLESHOOTING

Problem

A “humming” sound

can be heard.

The volume level

cannot be increased, or

the sound is distorted.

The sound effect

cannot be recorded.

The sound field

parameters and some

other settings on this

unit cannot be

changed.

This unit does not

operate properly.

“CHECK SP WIRES”

appears on the front

panel display.

There is noise

interference from digital

or high-frequency

equipment, or this unit.

This unit suddenly

turns into the standby

mode.

Cause

Incorrect cable connections.

The component connected to the OUT

(REC) jacks of this unit is turned off.

It is not possible to record the sound

effect by a recording component.

“10 MEM. GUARD” in the SET MENU

is set to ON.

The internal microcomputer has been

frozen by an external electric shock (such

as lightning or excessive static electricity)

or by a power supply with low voltage.

Speaker cables are short circuited.

This unit is too close to the digital or

high-frequency equipment.

The internal temperature becomes too

high and the overheat protection circuitry

has been activated.

Remedy

Firmly connect the audio plugs. If the problem

persists, the cables may be defective.

Turn on the power to the component.

Set “10 MEM. GUARD” in the SET MENU to

OFF.

Disconnect the AC power cord from the outlet

and then plug it in again after about 30 seconds.

Make sure all speaker cables are connected

correctly.

Move this unit further away from such

equipment.

Wait until this unit cools down and then turn it

back on.

Refer

to page

10 – 16

—

0110V430_50-56_EN(GB) 1/19/02, 8:06 PM52

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TROUBLESHOOTING

■ Tuner

FM stereo reception is

noisy.

There is distortion, and

clear reception cannot

be obtained even with a

good FM antenna.

The desired station

cannot be tuned in with

the automatic tuning

method.

Previously preset

stations can no longer

be tuned in.

The desired station

cannot be tuned in with

the automatic tuning

method.

There are continuous

crackling and hissing

noises.

There are buzzing and

whining noises

(especially in the

evening).

Problem

Cause

The characteristics of FM stereo

broadcasts may cause this problem

when the transmitter is too far away or

the antenna input is poor.

There is multipath interference.

The station is too weak.

This unit has been disconnected for a

long period.

The signal is weak or the antenna

connections are loose.

Noises result from lightning,

fluorescent lamps, motors, thermostats

and other electrical equipment.

A TV set is being used nearby.

Remedy

Check the antenna connections.

Try using a high-quality directional FM

antenna.

Use the manual tuning method.

Adjust the antenna position to eliminate

multipath interference.

Use a high-quality directional FM antenna.

Use the manual tuning method.

Re-store the stations.

Tighten the AM loop antenna connections

and orient it for best reception.

Use the manual tuning method.

Use an outdoor antenna and a ground wire.

This will help somewhat, but it is difficult to

eliminate all noise.

Move this unit away from the TV.

Refer

to page

—

35, 36

—

■ Remote control

Problem

The remote control

does not work nor

function properly.

Cause

Wrong distance or angle.

Direct sunlight or lighting (from an

inverter type of fluorescent lamp, etc.) is

striking the remote control sensor of this

unit.

The batteries are weak.

Remedy

The remote control will function within a

maximum range of 6 m (20 feet) and no more

than 30 degrees off-axis from the front panel.

Reposition this unit.

Replace all batteries with new ones.

Refer to

page

—

0110V430_50-56_EN(GB) 1/19/02, 8:06 PM53

GLOSSARY

■ Dolby Surround

Dolby Surround uses a 4 channel analog recording system

to reproduce realistic and dynamic sound effects: 2 main

left and right channels (stereo), a center channel for

dialog (monaural), and a rear channel for special sound

effects (monaural). The rear channel reproduces sound

within a narrow frequency range.

Dolby Surround is widely used with nearly all video tapes

and laser discs, and in many TV and cable broadcasts as

well. The Dolby Pro Logic decoder built into this unit

employs a digital signal processing system that

automatically stabilizes the volume on each channel to

enhance moving sound effects and directionality.

■ Dolby Digital

Dolby Digital is a digital surround sound system that

gives you completely independent multi-channel audio.

With 3 front channels (left, center, and right), and 2 rear

stereo channels, Dolby Digital provides 5 full-range audio

channels. With an additional channel especially for bass

effects, called LFE (low frequency effect), the system has

a total of 5.1 channels (LFE is counted as 0.1 channel).

By using 2-channel stereo for the rear speakers, more

accurate moving sound effects and surround sound

environment are possible than with Dolby Surround. The

wide dynamic range (from maximum to minimum

volume) reproduced by the 5 full-range channels and the

precise sound orientation generated using digital sound

processing provide listeners with previously unheard of

excitement and realism.

With this unit, any sound environment from monaural up

to a 5.1-channel configuration can be freely selected for

your enjoyment.

■ Matrix 6.1

The unit incorporates Matrix 6.1 decoder for Dolby

Digital and DTS multi-channel software that enables 6.1-

channel reproduction by adding the rear center channel to

existing 5.1-channel format. (The rear center channel is

created from rear left and right channels, and outputted

from virtual rear center speaker.) With this additional

channel, you can experience more dynamic and realistic

moving sound especially with scenes with “fly-over ” and

“fly-around ” effects.

■ Dolby Pro Logic

Dolby Pro Logic is an improved technique used to

decode vast numbers of existing Dolby Surround

softwares. This new technology enables a discrete 5-

channel playback with 2 main left and right channels, 1

center channel, and 2 rear left and right channels (instead

of only 1 rear channel for conventional Pro Logic

technology). A music mode is also available for 2-channel

sources in addition to the movie mode.

■ DTS (Digital Theater Systems)

Digital Surround

DTS digital surround was developed to replace the analog

soundtracks of movies with a 6-channel digital sound

track, and is now rapidly gaining popularity in movie

theaters around the world. Digital Theater Systems Inc.

has developed a home theater system so that you can

enjoy the depth of sound and natural spatial

representation of DTS digital surround in your home.

This system produces practically distortion-free 6-channel

sound (technically, a left, right and center channels, 2 rear

channels, plus an LFE 0.1 channel as a subwoofer, for a

total of 5.1 channels).

■ LFE 0.1 channel

This channel is for the reproduction of low bass signals.

The frequency range for this channel is 20 Hz to 120 Hz.

This channel is counted as 0.1 because it only enforces a

low frequency range compared to the full-range

reproduced by the other 5 channels in a Dolby Digital or

DTS 5.1 channel systems.

■ CINEMA DSP

DIGITAL

Since the Dolby Surround and DTS systems were

originally designed for use in movie theaters, their effect

is best felt in a theater having many speakers and

designed for acoustic effects. Since home conditions,

such as room size, wall material, number of speakers, and

so on, can differ so widely, it’s inevitable that there are

differences in the sound heard as well. Based on a wealth

of actually measured data, YAMAHA CINEMA DSP uses

YAMAHA original sound field technology to combine

Dolby Pro Logic, Dolby Digital and DTS systems to

provide the visual and audio experience of movie theater

in the listening room of your own home.

■ SILENT CINEMA

YAMAHA has developed a natural, realistic sound effect

DSP algorithm for headphones.

Parameters for headphones have been set for each sound

field so that accurate representations of all the sound field

programs can be enjoyed using headphones.

0110V430_50-56_EN(GB) 1/19/02, 8:06 PM54

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

GLOSSARY

■ Virtual CINEMA DSP

YAMAHA has developed a virtual CINEMA DSP

algorithm that allows you to enjoy DSP sound field

surround effects even without any rear speakers by using

virtual rear speakers.

It is even possible to enjoy virtual CINEMA DSP using a

minimal 2-speaker system that does not include a center

speaker.

■ PCM (Linear PCM)

Linear PCM is a signal format under which an analog

audio signal is digitized, recorded and transmitted without

using any compression. This is used as a method of

recording CDs and DVD audio. The PCM system uses a

technique for sampling the size of the analog signal per

very small unit of time. Standing for “pulse code

modulation”, the analog signal is encoded as pulses and

then modulated for recording.

■ Sampling frequency and number

of quantized bits

When digitizing an analog audio signal, the number of

times the signal is sampled per second is called the

sampling frequency, while the degree of fineness when

converting the sound level into a numeric value is called

the number of quantized bits.

The range of rates that can be played back is determined

based on the sampling rate, while the dynamic range

representing the sound level difference is determined by

the number of quantized bits. In principle, the higher the

sampling frequency, the wider the range of frequencies

that can be played back, and the higher the number of

quantized bits, the more finely the sound level can be

reproduced.

0110V430_50-56_EN(GB) 1/19/02, 8:06 PM55

SPECIFICATIONS

AUDIO SECTION

• Minimum RMS Output Power for Main, Center, Rear

20 Hz to 20 kHz, 0.06% THD, 8 Ω

[U.S.A. and Canada models] .............................................. 75 W

[Other models] .................................................................... 65 W

1 kHz, 0.06% THD, 8 Ω

[U.S.A. and Canada models] .............................................. 80 W

[Other models] .................................................................... 70 W

• DIN Standard Output Power

[Europe model]

1 kHz, 0.7% THD, 4 Ω ........................................................ 110 W

• Maximum Power (EIAJ)

[China, Korea and General models]

1 kHz, 10% THD, 8 Ω ........................................................... 95 W

• Dynamic Power (IHF)

8/6/4/2 Ω

[U.S.A. and Canada models] ......................... 95/115/140/160 W

[Other models] ............................................... 90/110/130/150 W

• Damping Factor

20 Hz to 20 kHz, 8 Ω ................................................... 80 or more

• Frequency Response

CD to Main L/R ...................................... 10 Hz to 100 kHz, –3 dB

• Total Harmonic Distortion

20 Hz to 20 kHz, 40 W, 8 Ω, Main L/R ................................ 0.06%

• Signal to Noise Ratio (IHF-A Network)

CD (250 mV, shorted) to Main L/R, Effect Off ................. 100 dB

• Residual Noise (IHF-A Network)

Main L/R ................................................................ 150 µV or less

• Channel Separation (1 kHz/10 kHz)

CD (5.1 kΩ terminated) to Main L/R ........................ 60 dB/45 dB

• Tone Control (Main L/R)

BASS Boost/Cut ...................................................... ±10 dB/50 Hz

TREBLE Boost/Cut ............................................... ±10 dB/20 kHz

• Phones Output ............................................................. 0.34 V/560 Ω

• Input Sensitivity

CD, etc .................................................................... 150 mV/47 kΩ

6CH INPUT ............................................................ 150 mV/47 kΩ

• Output Level

OUT (REC) ........................................................... 150 mV/1.2 kΩ

OUTPUT SUBWOOFER .......................................... 4.0 V/1.2 kΩ

VIDEO SECTION

• Video Signal Type ...................................................... NTSC or PAL

• Composite Video Signal Level ...................................... 1 Vp-p/75 Ω

• Signal to Noise Ratio ............................................................... 50 dB

• Frequency Response (MONITOR OUT) .... 5 Hz to 10 MHz, –3 dB

FM SECTION

• Tuning Range

[U.S.A. and Canada models] ............................ 87.5 to 107.9 MHz

[Other models] .............................................. 87.50 to 108.00 MHz

• 50 dB Quieting Sensitivity (IHF, 100% mod.)

Mono/Stereo ........................ 2.0 µV (17.3 dBf) /25 µV (39.2 dBf)

• Selectivity (400 kHz) ............................................................... 70 dB

• Signal to Noise Ratio (IHF)

Mono/Stereo .............................................................. 76 dB/70 dB

• Harmonic Distortion (1 kHz)

Mono/Stereo ................................................................. 0.2%/0.3%

• Stereo Separation (1 kHz) ....................................................... 45 dB

• Frequency Response ........................... 20 Hz to 15 kHz +0.5, –2 dB

AM SECTION

• Tuning Range ......................................... 530/531 to 1710/1611 kHz

• Usable Sensitivity ............................................................. 300 µV/m

GENERAL

• Power Supply

[U.S.A. and Canada models] ............................... AC 120 V/60 Hz

[Australia model] ................................................. AC 240 V/50 Hz

[U.K., Europe and Singapore models] ................ AC 230 V/50 Hz

[Korea model] ..................................................... AC 220 V/60 Hz

[China and General models] ..... AC 110/120/220/240 V, 50/60 Hz

• Power Consumption

[U.S.A. model] .................................................................... 210 W

[Canada model] ...................................................... 210 W/260 VA

[Other models] ..................................................................... 230 W

Standby Mode ............................................................. max. 0.9 W

• AC Outlets

[U.S.A., Canada, Europe and Singapore models]

.......................................................... 2 (Total 100 W maximum)

[China and General models] .................. 2 (Total 50 W maximum)

[U.K. and Australia models] ......................... 1 (100 W maximum)

• Dimension (W x H x D)

...................... 435 x 151 x 380 mm (17” x 5-15/16” x 15-1/16”)

• Weight ................................................................... 10.0 kg (21.3 lbs)

• Accessories ............................................................... Remote control

Batteries

75-ohm/300-ohm antenna adapter [U.K. model]

A/V cable [U.S.A., Canada and Australia models]

AM loop antenna

Indoor FM antenna

*Specifications are subject to change without notice.

0110V430_50-56_EN(GB) 1/19/02, 8:06 PM56

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia

V890260

RX-V430RDS

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

RX-V430RDS

AV Receiver

Ampli-tuner audio-vidéo

0100V430(GB)-cv1 1/18/02, 3:59 PM1

Yamaha RX-V430RDS de handleiding

Merk: Yamaha

Model: RX-V430RDS

Categorie: AV-ontvangers

Type: de handleiding

PDF downloaden

rapport

in andere talen

English: Yamaha RX-V430RDS Owner's manual
italiano: Yamaha RX-V430RDS Manuale del proprietario
français: Yamaha RX-V430RDS Le manuel du propriétaire
Deutsch: Yamaha RX-V430RDS Bedienungsanleitung
dansk: Yamaha RX-V430RDS Brugervejledning
Türkçe: Yamaha RX-V430RDS El kitabı
română: Yamaha RX-V430RDS Manualul proprietarului

Yamaha RX-V430RDS de handleiding

Yamaha RX-V430RDS de handleiding

in andere talen

Gerelateerde papieren