Zanussi ZGG62412XA Handleiding

Categorie
Koffie makers
Type
Handleiding
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you impeccable per-
formance for many years, with innovative technologies that help make life simpler – fea-
tures you might not find on ordinary appliances. Please spend a few minutes reading to get
the very best from it.
Visit our website to:
get tips, download our leaets, resolve possible malfunctions, obtain information on
customer care.
www.aeg.com
register your product and receive a better service:
www.aeg.com/productregistration
purchase accessories, consumables and original spare parts for your appliance.
www.aeg.com/shop
CUSTOMER SERVICE AND MAINTENANCE
We recommend always using original spare parts.
Always have the following information at hand when you contact customer services.
You can nd the information on the rating plate.
Model, appliance number (PNC), serial number.
Subject to changes
6
EN
CONTENTS
INTRODUCTION ......................................... 7
Symbols used in these instructions .................................7
Letters in brackets ............................................................7
Troubleshooting and repairs ............................................7
SAFETY ..................................................... 7
Fundamental safety warnings..........................................7
Designated use ................................................................8
Instructions .....................................................................8
DESCRIPTION ............................................ 8
Description of the appliance ...........................................8
Description of the control panel .......................................9
Description of milk container and accessories ..................9
PRELIMINARY CHECKS ............................... 9
Controls after transport ...................................................9
Installing the appliance ...................................................9
Connecting the appliance ................................................9
USING THE APPLIANCE FOR THE FIRST TIME 10
TURNING ON AND HEATING UP ................. 10
MAKING COFFEE USING COFFEE BEANS .... 10
CHANGING THE QUANTITY OF COFFEE IN THE
CUP ....................................................... 11
ADJUSTING THE COFFEE MILL ................... 12
MAKING ESPRESSO COFFEE WITH PRE
GROUND COFFEE INSTEAD OF BEANS ...... 12
DELIVERING HOT WATER .......................... 12
CHANGING THE QUANTITY OF HOT WATER . 12
MAKING CAPPUCCINO .............................. 13
CHANGING THE QUANTITY OF MILK AND COF
FEE FOR CAPPUCCINO .............................. 13
Changing the quantity of milk .......................................13
Changing the quantity of coee .....................................14
MAKING A NUMBER OF CUPS OF COFFEE WITH
THE JUG FUNCTION ................................. 14
CHANGING JUG FUNCTION PARAMETERS .. 14
CLEANING .............................................. 15
Cleaning the coee maker .............................................15
Cleaning the waste coee container ..............................15
Cleaning the drip tray ....................................................15
Cleaning the water tank .................................................16
Cleaning the spouts .......................................................16
Cleaning the pre-ground coee funnel ..........................16
Cleaning the inside of the coee maker .........................16
Cleaning the brewing unit .............................................16
Cleaning the milk container ...........................................16
Cleaning the coee jug ..................................................17
CHANGING AND SETTING MENU PARAMETERS ...17
Setting the language ....................................................17
Rinsing .......................................................................... 17
Changing the length of time the appliance remains on .17
Setting the clock ............................................................18
Setting auto-start time ..................................................18
Changing coee temperature ........................................18
Setting water hardness .................................................18
Programming coee ......................................................18
Programming cappuccino ..............................................18
Programming the jug .....................................................18
Programming water .......................................................18
Descaling .......................................................................18
Resetting default values (reset) .....................................19
Statistics ........................................................................19
Buzzer ...........................................................................19
Adjusting contrast ..........................................................19
TURNING THE APPLIANCE OFF ................. 20
TECHNICAL SPECIFICATION ....................... 20
DISPLAYED MESSAGES ............................. 21
TROUBLESHOOTING ................................ 22
6 7
EN
INTRODUCTION
Symbols used in these instructions
Important warnings are identied by these symbols. It is vital
to respect these warnings. Failure to observe the instructions
could result in electric shock, serious injury, burns, re or dam-
age to the appliance.
Danger!
Failure to observe the warning could result in possibly life
threatening injury from electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
N.B.!
This symbol identies important advice or information for the
user.
Letters in brackets
The letters in brackets refer to the legend in the Description of
the Appliance on page 3.
Troubleshooting and repairs
In the event of problems, follow the information given in the
sections “Displayed messages” and “Troubleshooting”.
If this does not resolve the problem, you should consult Custom-
er Services. For repairs, contact Customer Services only.
SAFETY
Fundamental safety warnings
The appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
Never immerse the appliance in water.
This is an household appliance only. It is not intended to be used in: sta kitchen areas in
shops, oces and other working environments; farm houses; by clients in hotels, motels and
other residential type environments; bed and breakfast type environments.
If the plug or power cable is damaged, it must be replaced by customer services only to avoid
all risk.
FOR EUROPEAN MARKETS ONLY:
This appliance can be used by children aged from 8 years and above if they have been given
supervision or instruction concerning use of the appliance in a safe way and if they under-
8
EN
Danger! This is an electrical appliance, it is therefore
important to respect the following safety warnings:
• Nevertouchtheappliancewithdamphands.
• Nevertouchtheplugwithdamphands.
• Makesurethesocketusedisfreelyaccessibleatalltimes,
enabling the appliance to be unplugged when necessary.
• Unplugdirectlyfromtheplugonly.
Never pull the power cable as you could damage it.
• To disconnect the appliance completely, place the main
switch (A23) on the side of the appliance in the 0 position.
• Iftheapplianceisfaulty,donotattempttorepair.
Turn it o using the main switch (A23), unplug from the
mains socket and contact Customer Services.
Important! Keep all packaging (plastic bags, polysty-
rene foam) away from children.
Danger of burns! This appliance produces hot water
and steam may form while it is in operation.
Avoid contact with splashes of water or hot steam.
Use knobs and handles.
Important! Do not grasp the coee maker when it is
out of the cabinet.
Do not rest recipients containing liquids or inammable or cor-
rosive materials on top of the appliance. Place the accessories
required to make the coee (the measure for example) in the
special holder.
Do not rest large objects which could obstruct movement or un-
stable objects on the appliance.
Important! Do not use the appliance when extracted.
Make sure the appliance is inactive before extracting it.
The only exception is adjusting the coee mill which must be
done with the machine out (see the section Adjusting the coee
mill”).
N.B.: Use original or manufacturer recommended acces-
sories and spare parts only.
Designated use
This appliance is designed and made to prepare coee and heat
drinks.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from improp-
er use of the appliance. This appliance can be installed over a
built-in oven if the latter is tted with a cooling fan at the rear
(maximum microwave power: 3 kW).
Instructions
Read these instructions carefully before using the appliance.
• Keeptheseinstructions
• Failuretorespecttheseinstructionsmayresultinburnsor
damage to the appliance.
The manufacturer is not liable for damage deriving from
failure to respect these instructions.
stand the hazard involved. Cleaning and user maintenance shall not be made by children
unless they are older than 8 and supervised. Keep the appliance and its cord out of the reach
of children aged less than 8 years.
Appliances can be used by persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision or instruction con-
cerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
When not in use and before cleaning, always unplug the appliance.
Surfaces marked with this symbol become hot during use (the symbol is present in
certain models only).
8 9
EN
N.B.! The appliance has a cooling fan.
This comes on whenever coee, steam or hot water is delivered.
After several minutes, the fan goes o automatically.
DESCRIPTION
Description of the appliance
(page 3 - A)
A1. Cup tray
A2. Service door
A3. Coee guide
A4. Waste coee container
A5. Brewing unit
A6. Cup tray lights
A7. On/OFF/stand-by button
A8. Control panel
A9. Jug
A10. Hot water and steam nozzle
A11. IEC connector
A12. Water tank
A13. Coee spout (adjustable height)
A14. Drip tray
A15. Bean container lid
A16. Bean container
A17. Grinding adjustment knob
A18. Pre-ground coee funnel door
A19. Measure
A20. Compartment for measure
A21. Pre-ground coee funnel
A22. Power cable
A23. Main switch
A24. Tray
Description of the control panel
(page 3 - B)
N.B.! Only icons B6, B7, B8, B9 and B14 concerning the
enabled commands will light up on the control panel.
N.B.! A light touch is enough to activate the icon.
B1. Display: guides the user in using the appliance.
B2. icon to activate or deactivate menu parameter set-
ting mode
B3. icon to turn lights A6 on and o
B4. icon to select the coee taste
B5. icon to select the type of coee (espresso, small cup,
medium cup, large cup, mug)
B6. ESC icon to exit the selected mode
B7-B8. icons to scroll forwards or backwards through the
menu and display the various modes
B9. OK icon to conrm the selected function
B10. icon to deliver a cup of coee
B11. icon to deliver two cups of coee
B12. icon to deliver cappuccino
B13. icon to deliver hot water
B14. “jug” icon to make a number of cups of coee directly in
the jug (provided)
Description of milk container and accessories
(page 3 - C)
C1. Frothed milk regulator
C2. Milk container handle
C3. CLEAN button
C4. Milk intake tube
C5. Frothed milk spout
C6. Milk frother
C7. Hot water spout
PRELIMINARY CHECKS
Controls after transport
After removing the packaging, make sure the product is com-
plete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact Customer
Services.
Installing the appliance
Important!
• Installationmustbeperformedbyaqualiedprofessional
in compliance with legislation in force in the country of in-
stallation (see Built-in installation).
• Thepackingelements(plasticbags,polystyrenefoam,etc.)
should be kept out of reach of children.
• Donotinstalltheapplianceinroomswherethetempera-
ture may drop to 0°C or lower.
• Customisethewaterhardnessassoonaspossiblefollowing
the instructions in the “Setting water hardness section.
Connecting the appliance
Danger! Check that the mains power supply voltage
corresponds to the value indicated on the rating plate on the
10
EN
bottom of the appliance.
Connect the appliance to an eciently earthed and correctly in-
stalled socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied pro-
fessional.To comply with safety directives, an omnipolar switch
with a minimum contact distance of 3 mm must be installed.
Do not use multiple sockets or extensions.
Important! Safety cutout devices must be included
in the mains power supply in compliance with the installation
regulations in the country concerned.
Disposing of the appliance
In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with household
waste, but taken to an authorised waste separation
and recycling centre.
USING THE APPLIANCE FOR THE
FIRST TIME
• Coeehasbeenusedtofactorytesttheapplianceanditis
therefore completely normal for there to be traces of coee
in the mill.
• Customisewaterhardnessassoonaspossiblefollowingthe
instructions in the “Setting water hardness section.
1. Connect the appliance to the mains supply.
Set the required language.
2. To set the language, use the icons (B7 and B8) to
choose the required language (g. 2). When the message
“PRESS OK TO CHOOSE ENGLISH” is displayed, press the OK
icon (B9) (g. 3) for 3 seconds until “ENGLISH INSTALLED”
is displayed. If you set the wrong language, follow the in-
structions in the “Setting the language section.
If your language is not available, select one from those dis-
played. The instructions refer to the English version.
Then follow the instructions displayed:
3. After 5 seconds, the appliance displays “FILL TANK. Extract
the water tank (g. 4), rinse and ll with fresh water with-
out exceeding the MAX line. Replace and push as far as it
will go.
4. Place a cup under the hot water spout (g. 5). (If the hot
water spout is not inserted, the appliance displays “INSERT
WATER SPOUT”. Attach it as shown in gure 6.
The appliance displays: “HOT WATER PRESS OK”.
Press the OK icon (B9) (g. 3) and after a few seconds a little
water comes out of the spout.
5. The machine now displays “TURNING OFF... PLEASE WAIT”
and goes o.
6. Extract the appliance by pulling it out using the handles
(g. 7). Open the lid and ll the container with coee
beans, then close the lid and push the appliance in.
The coee maker is now ready for normal use.
Important! Never introduce pre-ground coee, freeze
dried coee, caramelised beans or anything else which could
damage the appliance.
N.B.! When using the appliance for the rst time, you
need to make 4-5 cups of coee and 4-5 cappuccinos before the
appliance gives satisfactory results.
N.B.! Each time you turn the coee maker on by the ON/
OFF switch (A23), it performs a SELF-DIAGNOSIS cycle and then
goes o. To turn it on again, press the ON/OFF button (A7) (g. 1)
TURNING ON AND HEATING UP
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The appli-
ance is ready for use only after completion of this cycle.
Danger of burns! During rinsing, a little hot water
ows from the coee spouts.
To turn the appliance on, press the ON/OFF/stand-by button (A7)
(g. 1). The message “HEATING UP... PLEASE WAIT is displayed.
When heating is complete, the message changes to “RINSING”;
The appliance is at temperature when the message “MEDIUM
CUP NORMAL TASTE” is displayed.
If no icon is pressed within about 2 minutes, the time (if set, see
the “Setting the clock section) is displayed.
If the time has not been set, the appliance displays the last func-
tions set.
When any icon is pressed, “MEDIUM CUP NORMAL TASTE” is dis-
played again. The appliance is ready to make coee again.
MAKING COFFEE USING COFFEE
BEANS
1. The appliance is preset to make coee with a normal taste.
You can also choose coee with an extra-mild, mild, strong
or extra-strong taste. There is also a pre-ground coee op-
tion. To choose the required taste, press the icon (B4)
10 11
EN
(g. 8) a number of times. The required coee taste is dis-
played.
2. Place 1 cup under the spouts to make 1 coee (g. 9) or 2
cups for 2 coees (g. 9). Lower the spouts as near as possi-
ble to the cup for a creamier coee (g. 10).
3. Press the (B5) icon (B5) (g. 11) to select the type of
coee: espresso, small cup, medium cup, large cup, mug.
Now press the (icon (B10) (g. 12) if you want to make
a coee and the icon (B11) (g. 13) if you want to
make 2 coees. The appliance now grinds the beans and
starts delivering the coee into the cup.
Once the set amount of coee has been delivered, the ma-
chine stops delivery automatically and expels the exhaust-
ed waste coee into the waste coee container.
4. After a few seconds, the appliance is ready for use again.
5. To turn the appliance o, press the ON/OFF/stand-by but-
ton (A7) (g. 1). (Before going o, the appliance performs
an automatic rinse cycle. Take care to avoid scalds).
NOTE 1: If the coee is delivered a drop at a time or not at all, see
the Adjusting the coee mill” section.
NOTE 2: If the coee is delivered too fast and the cream is not
satisfactory, see the Adjusting the coee mill” section.
NOTE 3: Tips for a hotter coee:
• Proceedasdescribedinthesection“Changingandsetting
menu parameters”, “Rinse” function.
• Unlesspreheated,donotuseexcessivelythickcupsasthey
will absorb too much heat.
• Preheatthecupsbyrinsingthemwithhotwater.
NOTE 4: Coee delivery can be interrupted at any moment by
re-pressing the previously selected icon which remains lit during
the operation.
NOTE 5: As soon as delivery is nished, to increase the quantity of
coee in the cup, just keep pressing the previously selected icon
within 3 seconds after delivery has nished.
NOTE 6: When the appliance displays “FILL TANK”, ll the tank
with water or the appliance will not deliver coee.
(It is normal for there to be a little water left in the tank).
NOTE 7: After about 14 single (or 7 double) coees, the appliance
displays “EMPTY WASTE COFFEE CONTAINER”.
Even if not full, the empty waste coee container message is dis-
played 72 hours after the rst coee has been delivered. For the
72 hours to be calculated correctly, the machine must never be
turned o with the main switch in the 0 position.
To clean, open the service door on the front of the appliance
by pulling the spout (g. 16), extract the drip tray (g. 17) and
clean.
When cleaning, always extract the drip tray completely.
Important! When extracting the drip tray, the waste
coee container MUST always be emptied.
If this is not done, the machine may be clogged.
NOTE 8: Never extract the water tank while the machine is de-
livering coee.
If it is removed, it will not be possible to make the coee and
the appliance will display “GROUND TOO FINE ADJUST MILL AND
PRESS OK” and then “FILL TANK”. Check the level of water in the
tank and replace in the appliance.
To turn the appliance back on, insert the water spout if not al-
ready in place (g. 6), then press the OK icon (B9). “HOT WATER
PRESS OK” is displayed.
Press the OK icon (B9) within a few seconds and deliver water
from the spout for about 30 seconds. When delivery stops, the
basic modes are displayed again.
N.B.: The coee maker may request the operation to be
repeated a number of times until the air is completely elminated
from the hydraulic circuit.
N.B.: if this operation is not performed correctly or if
the machine is turned o, the basic modes may be displayed,
although the problem is in fact still present.
CHANGING THE QUANTITY OF COF
FEE IN THE CUP
The appliance is set by default to automatically make the follow-
ing types of coee:
• espresso
• smallcup
• mediumcup
• largecup
• mug
12
EN
To change the quantity, proceed as follows:
• Pressthe icon (B2) to enter the menu (g. 15). Press
the icons (B7) and (B8) (g. 2) until “PROGRAM COF-
FEE” is displayed.
• PresstheOKicon(B9).
• Selectthetypeofcoeeyouwanttochangebypressing
the icons (B7) and (B8).
• PresstheOK icon(B9) toconrmthe type ofcoee you
want to make.
• Usethe icons (B7) and (B8) to change the quantity
of coee. The progress bar shows the quantity of coee se-
lected.
• PresstheOKicon(B9)againtoconrm(ortheicon(B6)to
cancel the operation).
• PresstheESC(B6)icon(B6)(g.18)twicetoexitthemenu.
The appliance is now reprogrammed with the new settings and
is ready.
ADJUSTING THE COFFEE MILL
The coee mill is preset in the factory and should not require
adjusting. However, if after making the rst few coees you nd
that delivery is either too fast or too slow (a drop at a time), this
can be corrected by adjusting the grinding adjustment knob (g.
14).
Important! The grinding adjustment knob must only
be turned when the coee mill is in operation.
For slower delivery and creamier coee, turn one click anticlock-
wise (ner pre-ground coee).
For faster delivery (not a drop at a time), turn one click clockwise
(coarser pre-ground coee).
PREPARING COFFEE WITH PRE
GROUND COFFEE INSTEAD OF
BEANS
• Pressthe (B4) icon (B4) (g. 8) and select the pre-
ground coee function.
• Extractthemachinebypullingitoutwardsusingthehan-
dles (g. 7).
• Liftthecentrallid,placeonemeasureofpre-groundcoee
in the funnel (g. 19), push the appliance in then proceed
as described in the section “Making coee using coee
beans”.
N.B.: You can make just one coee at a time by pressing the
icon (B10) (g. 12).
• Afterusingthemachinewithpre-groundcoee,togoback
to making coee using beans, deactivate the pre-ground
coee function by pressing the icon (B4) (g. 8).
NOTE 1: Never introduce pre-ground coee when the machine is
o or it could spread through the inside of the appliance.
NOTE 2: Never add more than 1 measure, otherwise the appli-
ance will not make the coee.
NOTE 3: Use the measure provided only.
NOTE 4: Introduce only pre-ground coee for espresso coee
machines into the funnel.
NOTE 5: If more than one measure of pre-ground coee is used
and the funnel clogs, push the coee down with a knife (g. 21)
then remove and clean the brewing unit and machine as de-
scribed in the “Cleaning the brewing unit” section.
DELIVERING HOT WATER
• Alwaysmakesuretheapplianceisready.
• Turnthecappuccinomakeroutwardsandplaceacontainer
underneath (g. 6).
• Pressthe icon (B13) (g. 20). The appliance displays:
“HOT WATER PRESS OK”. Press the OK icon (B9) again and
hot water is delivered from the cappuccino maker into the
container underneath. (You should not deliver hot water
for more than 2 minutes at a time). To interrupt, press the
icon (B13) or the ESC icon (B6).
The appliance stops delivery once the set quantity is
reached.
CHANGING THE QUANTITY OF HOT
WATER
The machine is set by default to automatically delivery 200 ml
of hot water.
To change these quantities, proceed as follows:
• Placeacontainerunderneaththecappuccinomaker(g.5).
• Pressthe (B2) to enter the menu (g. 15) or press the
icons (B7) and (B8) (g. 2) until “PROGRAM HOT
WATER” is displayed.
• PresstheOKicon(B9)toconrm.
12 13
EN
• Select the required quantity of water by pressing the
icons (B7) and (B8). The progress bar shows the
quantity of water selected.
• PresstheOKicon(B9)toconrm(ortheESCicon(B6)to
cancel the operation.
• PresstheESC(B6)icon(B6)(g.18)twicetoexitthemenu.
• Theapplianceisnowreprogrammedwiththenewsettings
and is ready.
MAKING CAPPUCCINO
N.B.: Set the quantity of coee you want to use to make
the cappuccino in the “Program cappuccino function in the
menu.
• Selectthetasteofthecoeeyouwanttousetomakethe
cappuccino by pressing the icon (B4).
• Removethelidofthemilkcontainer.
• Fillthecontainerwithabout 100 gramsofmilk for each
cappuccino to be prepared (g. 23). Never exceed the MAX
level (corresponding to about 750 ml) marked on the con-
tainer. You should ideally use skimmed or semi-skimmed
milk at refrigerator temperature (about 5°C).
• Makesuretheintaketubeiscorrectlyinsertedintherubber
washer (g. 24) then replace the milk container lid.
• Positionthefrothedmilkregulator(C1)betweenthewords
CAPPUCCINO and CAFFELATTE printed on the milk container
lid.
The quantity of froth can be adjusted by moving the regu-
lator towards the word CAFFELATTE for a denser froth. Mov-
ing it towards the word CAPPUCCINO obtains a less dense
froth.
• Removethe hot waterspout (g 6) and attachthe milk
container to the nozzle (g. 25).
• Positionthemilkspoutasshowning.26andthenplacea
suciently large cup under the coee and milk spouts.
• Pressthe icon (g. B12). “CAPPUCCINO... is displayed
and after a few seconds, frothed milk ows out of the milk
spout into the cup below. (La fuoriuscita del latte si inter-
rompe automaticamente). (Delivery stops automatically).
• Theappliancedeliverscoee.
• Thecappuccinoisnowready.Sweetentotasteand,ifde-
sired, sprinkle the froth with a little cocoa powder.
NOTE 1: While making cappuccino, the ow of frothed milk or
coee can be interrupted by pressing the icon (B12).
NOTE 2: If the milk in the container nishes while delivering
frothed milk, remove the container and add milk. Reattach and
press the (B12) to request a cappuccino again.
NOTE 3: To ensure the complete cleanliness and hygiene of the
milk frother, always clean the circuits in the milk container lid
after making cappuccino.
“PRESS CLEAN!” ashes on the display.
• Placearecipientunderthemilkspout(g.26).
• PresstheCLEANbuttononthelid(C3)andholddownforat
least 5 seconds (g. 26) to start the cleaning function.
The appliance displays the message “CLEANING!” above a
progressive bar.
You should not release the CLEAN button until the bar is
complete indicating that cleaning is concluded.
When the CLEAN button is released, the function stops.
After cleaning, remove the milk container and place in the
refrigerator.
The milk should not be left out of the refrigerator for more
than 15 minutes.
NOTE 4: To change the quantity of coee or frothed milk the ap-
pliance delivers automatically into the cup, proceed as described
in the section Changing the quantity of coee and milk for cap-
puccino”.
CHANGING THE QUANTITY OF COF
FEE AND MILK FOR CAPPUCCINO
The appliance is set by default to automatically deliver a normal
cappuccino.
To change these quantities, proceed as follows:
Changing the quantity of milk
• Fillthecontainerwithmilkuptothemaximumlevelindi-
cated on the container.
• Pressthe icon (B2) to enter the menu (g. 15), then
press the icons (B7) and (B8) (g. 2) until “PRO-
GRAM CAPPUCCINO” is displayed.
• PresstheOKicon(B9)toconrm.“PROGRAMMILK”isdis-
played.
• PresstheOKicon(B9)again.
• Selectthequantityofmilkrequiredbypressingthe
icons (B7) and (B8). The progress bar shows the quantity of
NO froth
“Denser” froth
frothed milk regulator
“Less dense froth
14
EN
milk selected.
• PresstheOKicon(B9)toconrm(ortheESCicon(B6)to
cancel the operation.
• PresstheESC(B6)icon(B6)(g.18)twicetoexitthemenu.
Changing the quantity of coee
• Pressthe (B2) icon (B2) to enter the menu (g. 15),
then press the icons (B7) and (B8) (g. 2) until
“PROGRAM CAPPUCCINO” is displayed.
• PresstheOKicon(B9)toconrmthenthe icons (B7
and (B8) (g. 2) until “COFFEE FOR CAPPUCC. is displayed.
• PresstheOKicon(B9)again.
• Select the quantity of coee required by pressing the
icons (B7) and (B8). The progress bar shows the
quantity of coee selected.
• PresstheOKicon(B9)toconrm(ortheESCicon(B6)to
cancel the operation.
• PresstheESCicon(B6)(g.18)twicetoexitthemenu.
MAKING A NUMBER OF CUPS OF
COFFEE WITH THE JUG FUNCTION
Using this function you can automatically make a number of
cups of coee (4, 6) directly in the jug (A9) to keep the coee hot.
• TurnthejugliduntilthearrowlinesupwiththewordOPEN
and remove the lid.
Rinse the jug and lid.
• Closethejug byturningthe lid towardsCLOSEuntilitis
tightly closed and then place it under the coee spout.
Always position the jug with the handle facing to the right
or left as shown in the gure.
The coee spout (A13) must be fully raised to enable the
jug to be inserted.
“FILL BEAN CONT. AND WATER TANK, EMPTY WASTE CONT.,
PRESS OK” is displayed. Make sure the water tank is full, the
bean container is full enough and the waste coee contain-
er is completely empty.
• PresstheOKicon(B9).
The type of coee selected, for example “EXTRA-MILD JUG”,
and the number of cups you want to make with the jug are
displayed, for example JUG 4 CUPS”.
• Conrmbypressingthe icon (B14). The display shows a
progress bar which indicates coee making process.
When the progress bar is complete, the appliance nishes
the process and automatically goes back to the coee jug
function.
If on the other hand an incomplete progress bar is dis-
played, this means that the cycle has not been completed
correctly. Remove the jug and check the message which
appears on the display, consulting the section “DISPLAYED
MESSAGES”.
• RemovejugandleavethelidintheCLOSEpositiontokeep
the coee hot.
• Topourthecoee,turnthelidanticlockwiseuntilthearrow
is lined up with the spout of the jug.
Important! When the coee beans are insucient to
complete the required function, the appliance stops the process
and waits for the bean container to be lled again and the
icon (B14) to be pressed. For example, when you want to make
4 cups of coee but the beans are insucient, the appliance
makes 2 cups then stops making coee. Fill the bean container
and press the icon (B14). Once the container has been lled,
the appliance makes the 2 remaining cups only to reach the re-
quired number of 4 cups.
If there is not enough water in the tank to complete the required
function or the waste coee container is full, the appliance in-
terrupts the process.
To ll the water tank or empty the waste coee container, you
must remove the jug. This interrupts the programme.
After rectifying the problem, the programme must be started
again.
In this case, you must take the amount of coee already deliv-
ered into account to avoid the jug overowing.
CHANGING JUG FUNCTION PA
RAMETERS
The jug programme is factory set with default values.
These can be modied to suit your personal taste and saved.
You can select 5 dierent types of coee from extra-mild to
extra-strong and, with the aid of a graphic bar, 10 quantities of
coee.
To make these adjustments, proceed as follows:
14 15
EN
• Press the icon (B2) to enter the menu. Press the
icons (B7) and (B8) until “PROGRAM JUG” is dis-
played.
• PresstheOKicon(B9)andthenthe icons (B7) and
(B8) until JUG COFFEE TASTE” is displayed.
• PresstheOKicon(B9).
• Pressthe icons (B7) and (B8) to select a dierent
coee taste from extra-mild to extra-strong.
• ConrmtherequiredtastebypressingtheOKicon(B9).
• To changethe quantityof coee,pressthe icons
(B7) and (B8) until JUG LEVEL is displayed.
• PresstheOKicon(B9)toconrm.
• Abarrepresentingthequantityofcoeedeliveredforeach
cup is displayed and can be made shorter or longer. A com-
pletely full bar corresponds to the maximum quantity of
coee per cup.
• When the bar indicates the quantity of coee required,
press the OK icon (B9) to conrm.
• Tochangethequantityofcups,pressthe icons (B7)
and (B8) until “NR OF CUPS IN JUG” is displayed.
• SelecttheOKicon(B9)andthenpressthe icons (B7)
and (B8) to select the number of cups required (4, 6). JUG 4
CUPS” or JUG 6 CUPS” is displayed.
• PresstheOKicon(B9)toconrm.
• PresstheESC(B6)icon(B6)toexittheprogrammingmenu.
CLEANING
Cleaning the coee maker
Do not use solvents or abrasive detergents to clean the coee
maker. A soft damp cloth will suce.
Never wash any of the components of the coee maker in the
dishwasher.
The following parts of the machine must be cleaned regularly:
• Wastecoeecontainer(A4).
• Driptray(A14).
• Watertank(A12).
• Coeespouts(A13)
• Pre-groundcoeefunnel(A21).
• nsideofthemachine,accessibleafteropeningtheservice
door (A2).
• Brewingunit(A5).
• Coeejug(A9).
Cleaning the waste coee container
When “EMPTY WASTE COFFEE CONTAINER is displayed, the
waste coee container must be emptied and cleaned.
To clean:
• opentheservicedooronthefrontoftheappliance(g.16),
extract the drip tray (g. 17) and clean.
• Cleanthewastecoeecontainerthoroughly.
Important! When extracting the drip tray, the waste
coee container must always be emptied.
Cleaning the drip tray
Important! If the drip tray is not emptied the water
might overow.
This could damage the machine.
The drip tray is tted with a level indicator (red) showing the
level of water it contains (g. 28).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned.
To remove the tray:
1. Open the service door (g. 16).
2. Remove the drip tray and the waste coee container (g.
17).
3. Clean the drip tray and waste coee container (A4).
4. Replace the drip tray and waste coee container (A4).
5. Close the service door.
Cleaning the water tank
1. Clean the water tank (A12) regularly (about once a month)
with a damp cloth and a little mild washing up liquid.
2. Remove all traces of washing up liquid.
Cleaning the spouts
1. Clean the nozzles periodically using a sponge.
2. Check regularly that the holes in the coee spout are not
blocked.
If necessary, remove coee deposits with a toothpick (g.
27).
Cleaning the pre-ground coee funnel
• Checkregularly(aboutonceamonth)thatthepre-ground
coee funnel is not blocked (g. 21).
Danger! Before performing any cleaning operations,
the machine must be turned o by pressing the main switch
(A23) and unplugged from the mains power supply.
Never immerse the coee maker in water.
16
EN
Cleaning the inside of the coee maker
1. Check regularly (about once a week) that the inside of the
appliance is not dirty.
If necessary, remove coee deposits with a sponge.
2. Remove the residues with a vacuum cleaner (g. 30).
Cleaning the brewing unit
The brewing unit must be cleaned at least once a month.
Important! The brewing unit (A5) must not be re-
moved when the appliance is on.
Do not use force to remove the brewing unit.
1. Make sure the machine is correctly turned o (see “Turning
the appliance o”).
2. Open the service door (g. 16).
3. Remove the drip tray and waste coee container (g. 17);
4. Press the two red release buttons inwards and at the same
time pull the brewing unit outwards (g. 31).
Important! Do not use washing up liquid to clean the
brewing unit. It would remove the lubricant applied to the inside
of the piston.
5. Soak the brewing unit in water for about 5 minutes, then
rinse.
6. After cleaning, replace the brewing unit (A5) by sliding it
onto the internal support and pin at the bottom, then push
the PUSH symbol fully in until it clicks into place.
N.B.: If the brewing unit is dicult to insert, you must
rst adapt it to the right dimensions by pressing it forcefully
from the bottom and top as shown in the gure.
7. Once inserted, make sure the two red buttons have snapped
out.
8. Replace the drip tray and waste coee container.
9. Close the service door.
Cleaning the milk container
Important! Always clean the tubes inside the milk
container (C) when you prepare milk.
If there is still milk in the container, do not leave it out of the
refrigerator for longer than strictly necessary.
Clean the container each time you prepare milk as described in
Note 3 in the section “Making cappuccino”.
All components can be washed in a dishwasher, placing them in
the top basket of the dishwasher.
1. Turn the lid of the milk container clockwise then remove it.
2. Remove the milk spout and intake tube.
Groove
Frothed milk regulator
Support
Pin
spout
milk intake tube
16 17
EN
3. Remove the frothed milk regulator by pulling it outwards.
4. Wash all the components thoroughly with hot water and
mild washing-up liquid.
Make sure there are no milk residues left inside the holes
and the groove on the ne end of the frothed milk regula-
tor.
5. Check that the intake tube and spout are not clogged with
milk residues.
6. Replace the frothed milk regulator, milk spout and intake
tube.
7. Replace the milk container lid.
Cleaning the coee jug
Clean the jug with a damp cloth and mild washing up liquid.
N.B.: To avoid damaging the appearance of the jug, do
not wash in a dishwasher.
CHANGING AND SETTING MENU
PARAMETERS
When the appliance is ready, you can use the internal menu to
modify the following parameters and functions:
• Chooselanguage
• Rinsing
• Shut-otime
• Setclock
• Starttime
• Auto-start
• Temperature
• Waterhardness
• Programcoee
• Programcappuccino
• Programjug
• Programwater
• Descale
• Resettodefault
• Statistics
• Buzzer
• Contrast
Setting the language
To change the language on the display, proceed as follows:
• Pressthe icon (B2) to enter the menu. “CHOOSE LAN-
GUAGE” is displayed.
• PresstheOKicon(B9).
• Pressthe icons (B7) and (B8) until the required lan-
guage is displayed.
• PresstheOKicon(B9)toconrm.
• PresstheESC(B6)toexitthemenu.
N.B.: If you choose the wrong language, you can access
the menu directly to modify the parameter.
• Pressthe (B2) for at least 7 seconds until the appli-
ance displays the various languages.
• Choosetherequiredlanguageasdescribedinthesection
“Using the appliance for the rst time.
Rinsing
This function enables you to obtain hotter coee.
Proceed as follows:
• Whenyouturn theappliance on,if youwanttomakea
small cup of coee (less than 60 cc), preheat the cup by
rinsing it with hot water.
• Ifontheotherhandmorethan2/3minuteshavepassed
since the last coee was made, before requesting another
coee, you must preheat the brewing unit by rst press-
ing the icon (B2) to enter the menu then the
icons (B7) and (B8) to select the “RINSING” function. Press
the OK icon (B9).
“RINSING... PLEASE CONFIRM” is displayed.
Press the OK icon (B9) again.
Deliver the water into the underlying drip tray or alterna-
tively use this water to ll (and then empty) the cup to be
used for the coee to preheat it.
Changing the length of time the appliance
remains on
The appliance is set by default to go o automatically 30 minutes
after the last coee has been made.
To change this interval (max. 120 min), proceed as follows:
• Pressthe icon (B2) to enter the menu and then the
icons (B7) and (B8) until “SHUT-OFF TIME” is dis-
played.
• PresstheOKicon(B9)toconrm.
• Pressthe icons (B7) and (B8) to set the time after
which the appliance will go o (after 1/2 hour, 1 hour, 2
hours).
• PresstheOKicon(B9)toconrm.
Hole
Hole
18
EN
• PresstheESCicon(B6)toexit.
Setting the clock
• Pressthe icon (B2) to enter the menu and then the
icons (B7) and (B8) until “SET CLOCK” is displayed.
• PresstheOKicon(B9).
• Usethe icons (B7) and (B8) to set the hour, then
press the OK icon (B9) to conrm.
• Usethe icons (B7) and (B8) to set the minutes, then
press the OK icon (B9) to conrm.
• PresstheESC(B6)icon(B6)toexitthemenu.
Setting auto-start time
This function programmes the time the machine will come on
automatically.
• Makesuretheclockontheappliancehasbeenset.•
Press the icon (B2) to enter the menu and then the
icons (B7) and (B8) until “START TIME” is displayed.
• PresstheOKicon(B9).
• Usethe icons (B7) and (B8) to set the auto-start
time, then press the OK icon (B9) to conrm.
• Usethe icons (B7) and (B8) to set the minutes, then
press the OK icon (B9) to conrm.
• Pressthe icons (B7) and (B8) to activate the au-
to-start function until AUTO START” is displayed.
• AUTOSTARTPLEASECONFIRM”isdisplayed.PRESS THE OK
ICON B9. The symbol appears on the display.
• PresstheESC(B6)icon(B6)toexitthemenu.
• Todisableauto-start,pressthe icon (B2), then the
icons (B7) and (B8) until AUTO START” is displayed.
Press the OK icon (B9).
“PLEASE CONFIRM” is displayed
Press (B6) to disable, the ESC symbol disappears .
Changing coee temperature
To change coee temperature, proceed as follows:
• Pressthe icon (B2) to enter the menu and then the
icons (B7) and (B8) until “TEMPERATURE” is dis-
played.
• PresstheOKicon(B9).
• Pressthe icons (B7) and (B8) to select the required
coee temperature from low, medium and high.
• PresstheOKbutton(B9)toconrmthetemperatureselect-
ed.
• PresstheESCicon(B6)toexitthemenu.
Setting water hardness
The operating period can be extended if required, making desca-
ling less frequent by programming the machine on the basis of
the real lime content in the water used.
Proceed as follows:
• removethe“TotalHardnessTest”strip(attachedtopage2)
from its packaging then dip it fully in the water for a few
seconds,
Then remove and wait about 30 seconds (until it changes
colour and forms red squares).
• turn the appliance on by pressing the ON/OFF/stand-by
button (A7).
• Pressthe icon (B2) to enter the menu and then the
icons (B7) and (B8) until “WATER HARDNESS” is dis-
played.
• PresstheOKicon(B9).
• Pressthe icons (B7) and (B8) until the number co-
incides with the number of red squares on the test strip (for
example, if there are 3 red squares on the test strip, select
the message “WATER HARDNESS 3”
• PresstheOKicon(B9)toconrm.
The coee maker is now programmed to provide the des-
cale warning when actually necessary.
Programming coee
For instructions on programming coee, see the “CHANGING THE
QUANTITY OF COFFEE IN THE CUP” section.
Programming cappuccino
For instructions on programming cappuccino, see the section
“CHANGING THE QUANTITY OF MILK AND COFFEE FOR CAPPUC-
CINO”.
Programming the jug
For instructions on programming the jug, see the section
CHANGING JUG FUNCTION PARAMETERS”.
Programming water
For instructions, see the “CHANGING THE QUANTITY OF HOT WA-
TER” section.
Descaling
Important! Descaler contains acids.
Respect the safety warnings provided by the manufacturer and
given on the descaler pack.
18 19
EN
N.B.: Use the descaler recommended by the manufac-
turer only.
Use of other descalers invalidates the guarantee.
Failure to descale the appliance as described also invalidates the
guarantee.
When “PLEASE DESCALE !” is displayed, the machine requires
descaling.
Proceed as follows:
• makesurethemachineisready;
• Pressthe icon (B2) to enter the menu and then the
icons (B7) and (B8) until “DESCALE” is displayed.
• PresstheOKicon(B9).
The message ADD DESCALER PLEASE CONFIRM” is dis-
played.
• Emptythetankofwater,pourthecontentsofthedescaler
bottle into the tank respecting the instructions given on the
descaler pack, then add water..
Position a container with a capacity of 2 litres under the hot
water spout.
• PresstheOKicon(B9).Descalerowsoutofthehotwater
spout into the container below.
The appliance displays: “DESCALING”.
• Thedescaleprogrammeautomaticallyperformsaseriesof
deliveries and pauses.
• Afterabout30minutes“DESCALECOMPLETEPLEASECON-
FIRM” is displayed.
• PresstheOKicon(B9).“RINSINGFILLTANK”isdisplayed.
• Emptythewatertank,rinsetoeliminatedescalerresidues,
then ll with clean water.
• Replacethetankfullofcleanwater.
“RINSING PLEASE CONFIRM” is displayed again.
• PresstheOKicon(B9)again.
Hot water ows out of the spout into the container below
and “RINSING” is displayed.
• Wait until“RINSING COMPLETE PLEASE CONFIRM” is dis-
played.
• PresstheOKicon(B9).
“DESCALE COMPLETE” is displayed, then “FILL TANK!”.
Fill the tank again with clean water.
• Thedescaleprogrammeisnowterminatedandtheappli-
ance is ready to make coee again.
NOTE: If descaling is interrupted before completion, the
process must be begun again from the beginning.
Important! FAILURE TO DESCALE THE APPLIANCE REG-
ULARLY INVALIDATES THE GUARANTEE.
Resetting default values (reset)
If you change the original values, the default values can be reset
as follows:
• Pressthe icon (B2) to enter the menu and then the
icons (B7) and (B8) until “RESET TO DEFAULT is dis-
played.
• PresstheOKicon(B9)andtheappliancedisplays“RESETTO
DEFAULT PLEASE CONFIRM”.
• presstheOKbutton(B9)toresetthedefaultvalues;
Statistics
This displays statistics relating to the machine.
To display, proceed as follows:
• Pressthe icon (B2) to enter the menu and then the
icons(B7)and(B8)until“STATISTICS”isdisplayed.•
Press the OK icon (B9).
• Pressthe icons (B7) and (B8) to verify:
• Howmanycoeesandcappuccinoshavebeenmade.
• Howmanytimesthemachinehasbeendescaled.
• Howmanycappuccinoshavebeenmade;
• Thetotalnumberoflitresofwaterdelivered.
• PresstheESCicon(B6)oncetoexitthefunctionortwiceto
exit the menu.
Buzzer
This activates or deactivates the buzzer emitted by the machine
each time an icon is pressed or an accessory is inserted/removed.
N.B.: The buzzer is active by default.
• Pressthe icon (B2) to enter the menu and then the
icons (B7) and (B8) until “BUZZER” is displayed.
• Pressthe OKicon(B9).“BUZZERPLEASECONFIRM”isdis-
played.
• PresstheESC(B6)icon(B6)todisableortheOKicon(B9)to
enable the buzzer.
• PresstheESC(B6)icon(B6)toexitthemenu.
Adjusting contrast
To increase or reduce the contrast of the display, proceed as fol-
lows:
• Pressthe icon (B2) to enter the menu and then the
icons (B7) and (B8) until “CONTRAST” is displayed.
• PresstheOKicon(B9).
• Pressthe icons (B7) and (B8) until the required dis-
play contrast is reached. The progressive bar indicates the
level of contrast selected.
20
EN
• PresstheOKicon(B9)toconrm.
• Pressthe ESC(B6)icon(B6)oncetoexitthefunctionor
twice to exit the menu.
TURNING THE APPLIANCE OFF
Each time the appliance is turned o, it performs an automatic
rinse cycle which cannot be interrupted.
Danger of burns! During rinsing, a little hot water
ows from the coee spouts.
Avoid contact with splashes of water.
To turn the appliance o, press the ON/OFF button (A7).
The appliance performs the rinse cycle then goes o.
N.B.! If the appliance is not used for an extended peri-
od, place the main switch on the back of the appliance in the 0
position (A23).
TECHNICAL SPECIFICATION
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1350 W
Pressure: 15 bars
Water tank capacity: 1.8 litres
Size LxHxD: 594x 455x411 mm
Weight: 23/24 kg
The appliance complies with the following EC directives:
• LowVoltageDirective2006/95/ECandsubsequentamend-
ments;
• EMCDirective2004/108/ECandsubsequentamendments
• ECRegulation1275/2008forstandby.
Materials and accessories coming into contact with food conform
to European regulation (EC) no. 1935/2004.
20 21
EN
DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY
FILL TANK! The water tank is empty or positioned
incorrectly.
Fill the tank with water and/or insert it correctly,
pushing it as far as it will go.
GROUND TOO FINE ADJUST MILL AND
alternating with PRESS OK
The grinding is too ne and the coee
is delivered too slowly.
Turn the grinding adjustment knob one click
clockwise towards “7”.
GROUND TOO FINE ADJUST MILL AND
(alternating with)
PRESS OK
(then)
FILL TANK
The tank has been removed during
delivery.
Insert the tank and press the OK icon (B9).
“HOT WATER PRESS OK” is displayed.
Press the OK icon (B9) again.
The appliance is once again ready for use.
EMPTY WASTE COFFEE CONTAINER The waste coee container (A4) is
too full or more than 3 days have
passed since you last made coee
(this guarantees correct hygiene of
the machine).
Empty the waste coee container and clean,
then replace.
Important: when removing the drip tray, the
waste coee container MUST be emptied, even
if it is not completely full.
If this is not done, when you make the next cof-
fees, the waste coee container may ll up more
than expected and clog the machine.
INSERT WASTE COFFEE CONTAINER After cleaning, the waste coee con-
tainer has not been replaced.
Open the service door and insert the waste coee
container.
INSERIRE CAFFÈ PREMACINATO The “pre-ground coee” function has
been selected without placing any
pre-ground coee in the funnel.
The funnel (A21) is blocked.
Extract the appliance and place pre-ground cof-
fee in the funnel.
Empty the funnel with the help of a knife as de-
scribed in the section Cleaning the pre-ground
coee funnel”.
PLEASE DESCALE! The machine must be descaled. The descaling procedure described in the “Desca-
ling” section needs to be performed as soon as
possible.
LESS COFFEE Too much coee has been used. Select a milder taste or reduce the quantity of
pre-ground coee, then make the coee again.
FILL BEAN CONTAINER The coee beans have run out. Fill bean container
INSERT BREWING UNIT The brewing unit has not been re-
placed after cleaning.
Insert the brewing unit as described in the sec-
tion “Cleaning the brewing unit”.
CLOSE DOOR The service door is open Close the service door.
GENERAL ALARM! The inside of the appliance is very
dirty.
Clean the inside of the appliance thoroughly, as
described in the section Cleaning and mainte-
nance”.
If the message is still displayed after cleaning,
contact a customer services.
DISPLAYED MESSAGES
22
EN
TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Custo-
mer Services.
PROBLEM POSSIBLE CAUSE REMEDY
The coee is not hot The cups were not preheated.
The brewing unit has cooled down be-
cause 2/3 minutes have elapsed since the
last coee was made.
The temperature set is too low.
Warm the cups by rinsing them with hot
water.
Before making coee, preheat the brew-
ing unit by selecting the RINSING func-
tion in the menu.
Change the set temperature (see para-
graph “Changing coee temperature”).
The coee is not creamy enough The coee is ground too coarsely.
Wrong type of coee.
Turn the grinding adjustment knob one
click anticlockwise towards “1” while the
coee mill is in operation (g. 14).
Use a type of coee for espresso coee
makers.
The coee is delivered too slowly or a
drop at a time.
The coee is ground too nely. Turn the grinding adjustment knob one
click clockwise towards “7” while the cof-
fee mill is in operation (g. 14).
Continue one click at a time until coee
delivery is satisfactory.
The eect is only visible after delivering
two coees.
The coee is delivered too quickly The coee is ground too coarsely. Turn the grinding adjustment knob one
click anticlockwise towards “1” while the
coee mill is in operation (g. 14).
Avoid turning the grinding adjustment
knob excessively otherwise when you
select 2 cups, the coee may be delivered
a drop at a time.
The eect is only visible after delivering
two coees.
Coee does not come out of one of the
spouts.
The spouts are blocked. Clean the spouts with a toothpick (g.
27).
The coee does not come out of the
spouts, but from around the service door
(A2).
The holes in the spouts are clogged with
dry coee dust.
The coee guide (A3) inside the service
door is blocked and cannot swing.
If necessary, remove coee deposits
with a toothpick, sponge or sti bristled
kitchen brush (g. 23).
Thoroughly clean the coee guide (A3),
particularly near the hinges.
Water comes out of the spouts instead of
coee.
The pre-ground coee may be blocked in
the funnel (A21).
Clean the funnel (A27) with a wooden
or plastic fork, clean the inside of the
machine.
22 23
EN
PROBLEM POSSIBLE CAUSE REMEDY
The milk does not come out of the milk
spout (C5).
The intake tube is not inserted or is in-
serted incorrectly.
Insert the intake tube (C4) in the rubber
washer in the milk container lid (g. 24).
The milk is not well frothed. The milk container lid is dirty.
The frothed milk regulator is not positio-
ned correctly.
Clean the milk container lid as described
in the section Cleaning the milk contain-
e r ”.
Adjust following the instructions in the
section “Making cappuccino”.
The milk contains bubbles or squirts out
of the milk spout.
The milk is not cold enough or is not
semi-skimmed.
The frothed milk regulator is incorrectly
adjusted.
The milk container lid is dirty.
You should ideally use skimmed or
semi-skimmed milk at refrigerator tem-
perature (about 5°C). If the result is still
disappointing, try another brand of milk.
Move the frothed milk regulator slightly
towards the word “CAFFELATTE” (see sec-
tion “Making cappuccino”).
Clean the milk container lid as described
in the section Cleaning the milk contain-
e r ”.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Zanussi ZGG62412XA Handleiding

Categorie
Koffie makers
Type
Handleiding

in andere talen