Animo
A 200-309/99
Animo
Coffeemakers
Animo
Coffeemakers
Animo
Coffeemakers
Animo
aromatic
Animo
A 200
1/2
1
start
0
1
370
185
160
O
660
35
40
80
500
W- 40
E- 35
Fig. 3
E = Electriciteitaansluiting W = Wateraansluiting O = Overloopaansluiting
Electrical connection Water connection Overflow connection
Stromkabel Wasseranschluß Wasserablauf
Branchement électrique Branchement d'eau froid Branchement trop-plein
Animo
09/99A 200-3
Dit apparaat voldoet aan de EMC-richtlijn 89/336/EEG, 92/31/EEG en de
laagspanningsrichtlijn 73/23/EEG.
This appliance is in accordance with the EMC-Directive 89/336/EEC,
92/31/EEC and the low voltage directive 73/23/EEC.
Dieses Gerät wurde in Übereinstimmung gemäß EMV-Richtlinie 89/336/EWG,
92/31/EWG und Niederspannung-Richtlinie 73/23/EWG gebaut.
Cet appareil est conforme à la directive d'EMC 89/336/CEE, 92/31/CEE et à
la directive de basse tension 73/23/CEE.
Animo behoudt zich het recht voor om onderdelen op elk gewenst moment te wijzigen, zonder voorafgaande of directe kennisgeving aan de afnemer.
De inhoud van deze handleiding kan eveneens gewijzigd worden zonder voorafgaande waarschuwing. Deze handleiding is geldig voor de machine in
standaarduitvoering. Animo kan derhalve niet aansprakelijk worden gesteld voor eventuele schade voortvloeiende uit van de standaard uitvoering
afwijkende specificaties van de aan u geleverde machine. Voor informatie betreffende afstelling,onderhoudswerkzaamheden of reparaties waarin
deze handleiding niet voorziet, wordt u verzocht contact op te nemen met de technische dienst van uw leverancier. Deze handleiding is met alle
mogelijke zorg samengesteld, maar Animo kan geen verantwoording op zich nemen voor eventuele fouten in dit boek of de gevolgen daarvan.
Animo has the right to change parts of the machine at any time without advice or direct announcements to the client. The contents of this manual can
also be changed without any announcements. This manual is to be used for the standard model/type of the machine. Thus Animo cannot be held
responsible for any damage resulting from the application of this manual to the version delivered to you. For extra information on adjustments
maintenance and repair, contact the technical department of your supplier. This manual has been written very carefully. However ,Animo cannot be
held responsible neither for mistakes in the book nor for their consequences.
Animo behält sich das Recht vor, Einzelteile ohne vorherige Bekanntgabe an den Kunden zu ändern. Der Inhalt dieser Anleitung kann ebenfalls ohne
vorherige Bekanntgabe geändert werden. Diese Anleitung gilt für die Standardausführung der Maschine. Animo haftet daher nicht für Informationen
über Einstellungen, Wartungsarbeiten oder Reparaturen, die nicht in dieser Anleitung enthalten sind. Wenden Sie sich bitte gegebenenfalls an den
Kundendienst Ihres Händlers. Diese Anleitung wurde mit größtmöglicher Sorgfalt zursammengestellt. Animo haftet jedoch nicht für etwaige Fehler in
dieser Anleitung oder für die Folgen solcher Fehler.
Animo se réserve le droit de modifier les pièces à n’importe quel instant, sans avis préalable et sans obligation de notification au client. Le contenu de
ce manuel est également sujet à modification sans avis préalable. Ce manuel s’applique au modèle standard de la machine. Par conséquent, Animo
n’est past responsable pour les dommages éventuels découlant de l’application de ce manuel aux modèles non standard. Pour les renseignements
sur certains réglages, les travaux d’entretien ou réparations qui ne seraient pas traités dans ce manuel, Animo ne peut ètre tenu responsable des
erreurs éventuelles ni des dommages qui en dècouleraient.
GB
ITABLE OF CONTENTS
1. GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2. TECHNICAL DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3. INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5. PREPARATIONS BEFORE USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6. BREWING COFFEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
7. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7.1 descaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Animo
1
09/99A 200-3
Animo
A 200-309/99
2
These operating instructions should be read carefully to ensure that your coffee machine is operated
correctly and safely.
1. GENERAL DESCRIPTION
The Aromatic A200-3 coffee machine with a fixed water connection and a selector switch to choose a full
or a half jug of coffee. This means that fresh filter coffee can be made quickly at all times.
The machine is started by simply pressing the button. It operates on the through- principle of
instantaneous water heating thus eliminating warm-up time. The A200-3 has an extra hot plate so three
jugs of coffee can be kept warm simultaneously.
In figure 1 the main parts are indicated.
In figure 2 the controls are indicated.
Figure 1:
A - Lower hot plate
B - Glass jug 3x (art.no. 08208)
C - Removable filters (90/250) 2x (art.no. 08635)
D - Control panel
E - Upper hot plate
F - Third hot plate
The machine is supplied with the following accessories:
- Measuring spoon
- Operating manual
- Water supply hose approx. 1.5 m long
- Basket filter paper 90/250 approx 50 pieces (art.no. 01088 1000 pieces)
- 1 sachet coffee detanning agent (100 sachets for 10 grams art.no. 49009)
- 1 sachet descaling agent (48 sachets for 50 grams art.no. 49007)
Plastic and stainless steel (art.no. 08240), or completely stainless jugs (art.no. 99197) can be
supplied at an additional charge upon request.
2. TECHNICAL DETAILS
Type : A 200-3
Approx. hourly capacity coffee : 20 L/h
Buffer supply coffee : 5.4 L
Brewing time (1.8 Liter) : 6 min
Minimum amount of coffee : 1/2 jug
Level detection : electronic
Water supply : swivel 3/4”
Min. - Max. water pressure : 1-8 bar
Filter paper size : 90/250
Lenght of electric cable : 1.4 m
Dimensions : See fig. 3
Empty weight : 8 kg
Power supply (50/60 Cy) Capacity Fuse
220 V 1 phase/Neutral 2150 W 16 A
230 V 1 phase/Neutral 2350 W 16 A
240 V 1 phase/Neutral 2575 W 13 A
Technical alterations are reserved
Animo
3
09/99A 200-3
3. INSTALLATION
Follow the instruction to place and connect the
machine, specified blow:
• Place the machine on a firm and flat solid
surface where it can be connected to the
electricity and water supplies.
• The A 200-3 should be placed near a
manually-operated water tap. The water
supply hose is 1.5 metres long.
• When placing the machine, bear in
mind that it is equipped with an overflow
device.
The machine should be connected as
demonstrated in the diagrams shown below,
depending on the machine’s electrical fittings.
• (Fig. 4) For 220V-240V 1 Phase/neutral
with plug socket.
• (Fig. 4) For 220V -240V 1 Phase/neutral
(3 core electric cable).
The following remarks apply to figure 4:
• If the plug fitted on the machine cable
does not fit in your socket, replace it with
a new plug that does fit.
• The replaced plug should be disposed of
as it can be dangerous if plugged in a
socket.
The following points should be observed when
wiring a new plug:
• The green/yellow-coloured wire
(“EARTH”) should be connected to the
terminal which is either marked with the
letter “E”, the “earth” symbol ( ), or
coloured green or green/yellow.
• The blue-coloured wire (“NEUTRAL”) should
be connected to the terminal which is either
marked with the letter “N” or coloured black.
• The brown-coloured wire (“PHASE”) should
be connected to the terminal which is either
marked with the letter “L” or coloured brown.
IMPORTANT !
The three core main cable (fig. 4) has the
following wiring code:
Green/Yellow - Earth
Blue - Neutral
Brown - Phase
WARNING
* Always remove the plug from the socket if the machine has to be opened for repair or
maintenance.
* Do not put the machine in areas where the temperature drops below freezing point
because there is always water left in the system.
* Always plug the machine into an earthed wall socket.
* Do not submerge or spray the machine.
* Have all repairs carried out by a specially trained technician.
* When the appliance is in use, some of the components will get very hot
* Make sure that the main cable does not come into contact with the hot plates
* If the machine is not used it is advisable to remove the plug from the socket and to turn off
the water tap.
* Always observe local rules while installing the unit and use approved materials and parts.
!
fig. 4
Green/Yellow - Earth (E)
Blue - Neutral (N)
Brown - Phase (L)
Animo
A 200-309/99
4
6. BREWING COFFEE
1. Place the filterpaper (90/250) with the
appropriate amount of coffee (fine ground
for filter coffee units) in the basket filter.
The amount can be measured with the
supplied measuring spoon. Generally
speaking, you will need about 70 - 80
gram per 1.8 l jug.
2. Place an empty jug on the lower hot
plate.
3. Check that the machine is switched on,
main switch on (fig. 2B), and switch
on the lower hot plate (fig. 2F).
4. Turn the selection switch (fig. 2C) to the
required amount.
5. Press the start switch (fig. 2D).
6. The orange signal lamp (fig. 2A) on
the machine will now light up and
the filter coffee will be prepared.
7. When the signal lamp goes out again, the
hot water supply will stop. After about 1
minute, all of the coffee will have been
poured through the filter.
8. Stir the coffee in the jug briefly and pour,
or place the full jug on one of the upper
hot plates. The upper hot plate can be
switched on separately using the appropriate
switch (fig. 2E) or switch on the third hot
plate (fig. 2G).
9. The machine is ready to be used again after
the basket filter has been cleaned.
4. CONTROL PANEL
A - Signal lamp for heating element
B - On/off switch
C - Selection switch for full or half jug
D - Start switch
E - On/off switch for upper hot plate
F - On/off switch for lower hot plate
G - On/off switch for third hot plate
5. PREPARATIONS BEFORE USE
The following procedure should be carried out
before a new machine is used.
1. Connect the supplied water hose to the
coupling nut swivel joint at the rear of the
machine and to a manually-operated
water tap. ATTENTION! Use cold water only.
2. Slide the basket filter into the machine
and place an empty jug on the lower hot
plate.
3. Put the plug of the third hot plate into the
female connector at the back of the
machine. After you have followed the
instructions above, place the plug in the
socket.
4. Turn the machine on using the switch
(fig. 2B).
5. Turn the selection switch (fig. 2C) to the
desired amount.
6. Press the start switch (fig. 2D) and the
water reservoir will fill up.
7. The orange signal lamp (fig. 2A) will now
remain lit until the water has run through.
The machine is ready for use when the
light has gone out again.
Animo
5
09/99A 200-3
7. MAINTENANCE
• The machine can be cleaned with a clean,
damp cloth.
• The jug and basket filter can be cleaned in the
same way. Attention! The basket filter should
not be placed in a dishwasher.
• Coffee stains in the jugs can be removed
using Animo coffee stain remover.
• The machine can leave lime deposits
during use. The machine should be
descaled regularly in order to ensure that it
functions efficiently. Animo scale remover
is recommended.
Animo supplies both products in the
following quantities:
- Coffee detanning agent
100 sachets for 10 grams art.no. 49009
- Descaling agent
48 sachets for 50 grams art.no. 49007
7.1Descaling
1. Switch off the machine (fig. 2B).
2. Slide the basket filter into the machine
3. Place an empty jug on the lower hot plate.
4. Dissolve 1 sachet of 50 grams of Animo
descaling agent remover in 1 litre of
lukewarm 60 -70˚C water (see instructions
for use on the labelling).
5. Remove the plug of the third hot plate
at the back of the machine.
6. Unscrew the third hot plate at the front
(See arrow fig. 2).
7. Remove the third hot plate and the
st.st. safety-lid
8. Pour 1 litre of Animo descaling agent
remover into the reservoir (fig. 1E) and
switch on the machine (fig. 2B).
9. Turn the selection switch (fig. 2C) to the
half position and press the start button
(fig. 2D). The solution will now begin to
flow through the system.
* Attention! If the machine begins to
steam heavily, switch it off immediately
(fig. 2B). Wait for 1 minute. The solution
will flow through automatically. Switch the
machine back on. Press the start button
(fig. 2D) as well.
10. When half of the solution has run through
the machine, switch it off for about 2
minutes (fig. 2B). The solution will now
undergo a reaction with the lime scale.
11. After the pause, switch the machine back
on and allow the rest of the solution to
flow through the machine. Press the start
button again (fig. 2D).
* Attention! Keep an eye on the reservoir
while the solution is running through
the machine. Turn the machine off as
soon as the reservoir is empty. Then rinse
clean the metal contacts in the cold water
reservoir with water or a wet cloth.
12. Replace the parts, mentioned in point 7.
13. After descaling the machine, rinse
thoroughly by carrying out the normal
coffee preparation process 3 times
(without paper filters and coffee).
14. Clean the basket filter and jug thoroughly.
15. The machine is now ready to be used
again.
Animo B.V. Headoffice
Dr. A.F. Philipsweg 47
P.O. Box 71
9400 AB Assen
The Netherlands
Tel. no. +31 (0)592 376376
Fax no. +31 (0)592 341751
E-mail: [email protected]
Internet: http://www.animo.nl
Accredited by
the Dutch Council
for Certification
0697 Rev. 1 070999 Animo 09943
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
in andere talen
- English: Animo A200-3 Owner's manual
- français: Animo A200-3 Le manuel du propriétaire
- Deutsch: Animo A200-3 Bedienungsanleitung
Gerelateerde papieren
-
Animo A100 and A200 de handleiding
-
-
-
-
-
-
-
-
-