Yamaha DPX-1000 de handleiding

Merk: Yamaha

Model: DPX-1000

Categorie: Dataprojectoren

Type: de handleiding

DPX–1000

Digital Cinema Projector

UCAK

OWNER’S MANUAL

000_DPX-1000(U)H14 03.2.19, 1:38 PM3

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the

obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped.

15 Be sure to allow spaces of at least 30cm above, behind and on

both sides the unit.

16 Do not place the following objects on this unit:

A vessel with water in it. If the vessel falls by vibrations and

water spills, it may cause damage to the unit, and/or you may

get an electric shock.

IMPORTANT!

Please record the serial number of this unit in the space below.

Model:

Serial No.:

The serial number is located on the bottom of the unit.

Retain this Owner’s Manual in a safe place for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

IMPORTANT SAFETY INSTRUCTIONS

100_DPX-1000(E)UL Caut 03.2.20, 9:11 AM2

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void

your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used.

Follow all installation instructions. Failure to follow

instructions could void your FCC authorization to use this

product in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will not

result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the operation

of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is

found to be the source of interference, which can be determined

by turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures:

Relocate either this product or the device that is being affected

by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe

Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend

you to avoid prolonged exposure from excessive volume levels.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation

Address: 6660 Orangethorpe Avenue

Buena Park, CA90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: Projector

Model Name: DPX-1000

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See the user manual instructions if interference to radio reception is suspected.

100_DPX-1000(E)UL Caut 03.2.19, 11:58 AM3

Caution: Read this before operating this unit.

• To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

Installation

• Install this unit in a well-ventilated, cool, dry, clean place with

at least 30 cm (1 feet) clearance on the top, right and left, and

at the back of this unit — away from direct sunlight, heat

sources, vibration, dust, moisture, and/or cold.

• Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds. To prevent fire or

electrical shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

• Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

• On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may cause electrical

shock to the user and/or damage to this unit.

• Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to restrict heat dissipation. If the temperature inside

this unit rises too much, it may cause fire, damage to this unit,

and/or personal injury.

• When installing this unit on the ceiling, make sure the ceiling

has sufficient strength to support this unit and the ceiling

mounts for an extended period of time. Installation must be

performed only by qualified service personnel.

Operation

• Remove the lens cover before starting any operation of this unit

to prevent the heat from staying around the lens. Operation

with the cap on may cause damage to this unit.

• Do not plug in this unit to a wall outlet until all connections are

complete.

• Only the voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than that

specified.

• Do not use force on switches, knobs and/or cords.

• Do not operate this unit upside-down. It may overheat, possibly

causing damage.

• Take care of this unit so that no foreign objects and/or liquid

drop inside this unit.

• To prevent damage by lightning, disconnect the power cord

from the wall outlet during an electrical storm.

• Do not look into the lens while this unit is turned on. It may

cause serious damage to your eyesight.

• Before moving this unit, press STANDBY/ON to set this unit

in the standby mode, and disconnect the AC power plug from

the wall outlet.

• Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reason.

• When not planning to use this unit for a long period of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

• When disconnecting the power cord from the wall outlet, grasp

the plug; do not pull the cord.

• Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

Others

• Clean the lens carefully so as not to create any scratches by

using a blower or lens paper.

• Replace the lamp when the LAMP warning indicator blinks in

red after the lamp usage has exceeded 2000 hours. Follow the

lamp replacement procedure described in this manual.

For U.K. customers

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be

connected to the terminal in the plug which is marked by the letter

E or by the safety earth symbol or coloured GREEN or GREEN-

and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an appropriate

3 pin plug fitted. For details, refer to the instructions described

below.

Note

• The plug severed from the mains lead must be destroyed, as a plug with

bared flexible cord is hazardous if engaged in a live socket outlet.

For Canadian customers

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-

003.

100_DPX-1000(E)UL Caut 03.2.19, 5:56 PM4

English

If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place

to install this unit by avoiding the places listed below.

1. Places where the temperature and humidity vary greatly

• Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely

low.

• This unit must be used within a temperature range of 5—35°C.

2. Places without adequate ventilation

• Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.

• Do not cover the ventilation slots of this unit not to obstruct the heat dissipation.

• Install this unit on the firm surface.

• Do not cover this unit with a tablecloth, etc.

• Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.

• If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.

3. Places where it gets dusty

• If the filter is blocked with dust, the temperature of this unit may become too high.

4. Places with too much vibration or impact

• Vibration and impact can damage parts of this unit.

5. Places where this unit gets exposed to water or high humidity

• If this unit is exposed to water or high humidity, it may cause a fire or electrical shock.

6. Unstable places

• If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.

7. In close proximity to a Radio or Stereo

• The unit may interfere with reception if placed in close proximity to a radio or television receiver.

Important

• To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.

Accessory check

Please check that all accessories listed here are included in your package.

Inappropriate places for installation

RESET

123

VIDEO

STILL HIDE

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

BD4

S VIDEO

INPUT

MEMORY

DVI

• Remote control • Batteries (AA, UM-3 or R6)

• Pin/BNC adapters

• Power cable

• Lens cover

100_DPX-1000(E)UL Caut 03.2.19, 11:58 AM5

E-1

INTRODUCTION

INSTALLATION

CONNECTIONS

BASIC OPERATION

ADDITIONAL

INFORMATION

English

ENGLISH

Features

Contents

• Bright, high contrast images achieved through

DLP™ technology

• HDTV capable 1280 x 720 pixel wide DMD™

element

• A bright, high resolution large diameter lens

• Electronic lens adjustment

— Zoom, Focus, Vertical Position, Optical Iris

Diaphragm —

(DLP™ and DMD™ are trademarks of Texas Instruments.)

• Low operating noise made possible by Yamaha

sound technology

• High quality progressive reproduction of film

sources thanks to 3-2 pulldown detection

• 6 memory settings and an abundance of image

adjustment functions

• Digital Visual Interface (DVI)

HDCP Compatible

INTRODUCTION

Features ............................................. 1

Part Names and Functions

Front panel and controls ....................................................... 2

Connections .......................................................................... 3

Remote control ..................................................................... 4

Using the remote control ...................................................... 5

Loading the batteries into the remote control ....................... 5

Using the remote as a wired remote control ......................... 5

INSTALLATION

Installation

Installation methods ............................................................. 6

Screen and projection distance ............................................. 7

Projection image position ..................................................... 8

Keystone ............................................................................... 8

CONNECTIONS

Connecting the unit

Connecting A/V components ................................................ 9

Connecting to a computer ................................................... 10

BASIC OPERATION

Basic Operations

Turning on the power ......................................................... 11

Turning off the power ......................................................... 11

Preparations for projection ................................................. 12

Select an input .................................................................... 13

Select a display aspect ........................................................ 14

Other functions ................................................................... 15

Indicators ............................................................................ 15

Menu structure ................................... 16

1 <IMAGE> ...................................................................... 17

2 <SIGNAL> .................................................................... 19

3 <INITIAL> .................................................................... 20

4 <SETUP> ...................................................................... 21

Menu operation

Menu screen and operating buttons .................................... 22

Basic menu operation ......................................................... 23

Submenus ........................................................................... 24

Basic submenu operation .................................................... 25

One-touch image menu ...................................................... 28

Changing the menu location ............................................... 28

Memory function

Selecting the memory setting number ................................ 29

Resetting to the factory default settings ............................. 30

ADDITIONAL INFORMATION

Additional information

Glossary .............................................................................. 31

Projectable signals .............................................................. 33

Message display ................................................................. 34

Maintenance

Regular care ........................................................................ 35

Filter replacement ............................................................... 35

Replacing the lamp cartridge .............................................. 36

Troubleshooting .................................. 37

Specifications

Specifications ..................................................................... 38

Dimensional drawing ......................................................... 39

101_DPX-1000(E)01-05 03.2.19, 11:59 AM1

E-2

Part Names and Functions

1 STANDBY/ON indicator

2 STANDBY/ON button

Switches the unit between Standby and On (operational)

modes.

3 ESCAPE button

Use this button to exit from submenu mode.

4 PATTERN button

Switches the built-in test pattern display on and off.

5 ASPECT button

Selects the display aspect of the projection image. Press the

button to display the aspect presently being used. Pressing the

button again within 2 seconds will switch the unit to the next

aspect mode.

6 LAMP warning indicator

7 COVER warning indicator

■ Front panel and controls

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

DIGITAL CINEMA PROJECTOR DPX-1000

ASPECT

Front remote control sensor

STANDBY/ON indicator

Ventilation (Exhaust) vent

Lens cover

Lens

Adjuster

Use this to make fine adjustments

to the projection angle.

8 (Enter) button

Press this button to set values and enter into submenus.

9 MENU button

Press this button to display the general settings and adjustments

menu.

0 SETTING button

Selects the various lens adjustment modes.

q INPUT button

Press this button to display the input source and input signal

selection menu.

w Cursor button

Use the h, g, –, + buttons for functions such as system

operations, menu item selection, and changing system values.

e FAN warning indicator

r TEMP warning indicator

Ventilation inlet

Lamp cover

101_DPX-1000(E)01-05 03.2.19, 11:59 AM2

E-3

INTRODUCTION

English

DVI

INPUT B

RGB/YP

/YC

D4 VIDEO G/Y B/P

R/P

INPUT A

HD/SYNC VD

OUT IN

REMOTE

RS-232C

S-VIDEO VIDEO

TRIGGER OUT

1234567 809

wer

DVI

INPUT B

RGB/YP

BPR/YCBCR

D4 VIDEO G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC VD

OUT IN

REMOTE

RS-232C

S-VIDEO VIDEO

TRIGGER OUT

1 INPUT B (D-Sub 15 pin)

This is the input connector for signals (RGB/YPBPR/YCBCR)

from a component video or RGB source. Use a D-Sub monitor

cable when connecting another component to the DPX-1000

through this connector.

2 D4 VIDEO (D connector)

This connector receives video signals from the D connector of

other A/V components. It is compatible with the D1—D4

formats. (This connector is designed for the Japanese D format

only.)

3—7 INPUT A (BNC jacks)

These are input jacks for signals from component video or

RGB sources. Component signals from A/V equipment should

be connected to ports 3—5, and RGB signals from Computer

equipment to ports 3—7. Use a BNC cable when connecting

other components to the DPX-1000 through these jacks.

3 G/Y (G, or luminance signal)

4 B/P

B/CB (B, or color difference signal)

5 R/P

R/CR (R, or color difference signal)

6 HD/SYNC (horizontal sync signal, composite sync signal)

7 VD (vertical sync signal)

8 S-VIDEO (Mini DIN jack)

This jack receives S VIDEO signals from the S-VIDEO output

jack of other A/V components. Use an S VIDEO cable when

connecting other components to the DPX-1000 through this

jack.

■ Connections

Part Names and Functions

Rear remote control sensor

9 VIDEO (Pin jack)

This jack receives composite signals from jacks of other A/V

components. Use a video pin cable when connecting other

components to the DPX-1000 through this jack.

0 AC inlet

q DVI (DVI jack)

This jack receives DVI signals from computer equipment or

DVI signals from A/V equipments.

w REMOTE IN/OUT jack

Connect the remote control to the IN jack when using it

through a cable. Codes input through the IN jack will be output

directly through the OUT jack.

e RS-232C (D-sub 9 pin)

This jack is used for factory testing.

r TRIGGER OUT

This jack outputs control signals to external components. A

potential of 12V/Maximum 200 mA is provided when the

DPX-1000 is projecting.

AC inlet

Plug in the supplied power cord here.

101_DPX-1000(E)01-05 03.2.19, 11:59 AM3

E-4

Part Names and Functions

■ Remote control

Buttons with identical names to those on the main unit perform

identical functions. To use the remote, point it at the remote control

sensor on the front or back of the unit from a distance of no more

than 7 m (23 feet).

1 Transmit indicator

This indicator will light up when the unit is sending infra-red

signals to the main unit.

2 AUTO button

Pressing this button will automatically adjust the unit to the

best settings for projection by retuning the frequency of the

projection to that of the source component.

3 V. POS button

Switches on and off the adjustment mode for the vertical

positioning of the entire image.

4 ZOOM button

Switches on and off the size adjustment mode for the image

being projected.

5 IRIS button

Switches on and off the lens iris diaphragm change mode.

6 ESCAPE button

Press this button to exit from a sub-menu.

7 Cursor buttons

Use the h, g, –, + buttons to move the cursor within the

interface.

8 ASPECT button

Selects the display aspect of the projection image. Press the

button to display the aspect presently being used. Pressing the

button again within 2 seconds will switch the unit to the next

aspect mode.

9 STILL button

Stops a moving image to display a still of the desired image.

Press STILL again to cancel this function.

RESET

123

VIDEO

STILL HIDE

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

BD4

S VIDEO

INPUT

MEMORY

DVI

RESET

HID

INPUT

ENU

PATT

V. POS

FOCUS

AUTO

ID-2

ID-1

0 INPUT area

Directly selects the input jack.

q MEMORY area

Calls up stored video memory directly.

w RESET button

Press this button to reset all parameters altered in the menu to

their default factory settings.

e button

Switches the unit between Standby and On (operational)

modes.

r FOCUS button

Switches on and off the focus adjustment mode for the image

being projected.

t PATT (PATTERN) button

Switches the built-in test pattern display on and off.

y MENU button

Press this button to display the general settings and adjustments

menu.

u (Enter) button

Use this button to set values and enter into submenus when the

menu is being displayed. Pressing the button when the menu is

not being displayed will call up the in-line menu. (see page 28.)

i INPUT button

Press this button to display the input source and input signal

selection menu.

o LIGHT switch

Pressing this switch will light up the often used 2, 6, 8, e,

y, i buttons. The lights will switch off if no operation is

performed within 10 seconds.

p HIDE button

Press this button to temporarily halt projection of the image

being displayed. Press the HIDE button once more to cancel

this function.

a Remote control code switch

This remote control will work when it has the same code as

that set on the menu. The default setting on the menu is ID-1.

s Remote control cable jack

Use this jack to connect the remote control to the main unit

with a cable.

101_DPX-1000(E)01-05 03.2.19, 11:59 AM4

E-5

INTRODUCTION

English

Part Names and Functions

Important

• Bright light, fluorescent light etc. on the remote sensor on the main unit may inhibit the normal functioning of the remote control.

• The remote may not function normally if there is an obstacle blocking the signal between the remote and the remote control sensor

on the main unit.

• The above are approximate figures.

■ Using the remote control

Use the remote control under the following conditions. The remote control will not function if it is used outside the angles and/or range

detailed here.

■ Loading the batteries into the remote

control

1. Remove the battery compartment cover from the

back of the remote control.

2. Insert two batteries (AA, UM3, or R6 type), matching

the polarity markings (+, –) on the batteries with

those in the battery compartment.

3. After inserting the batteries, close the cover until it

snaps into place.

Important

• If the remote must be used closer to the main unit than

normal, or does not always operate correctly, exchange the

batteries for new ones.

• Do not mix old and new, or different types of battery.

• Remove the batteries if you do not plan to use the unit for a

long time.

• If the batteries leak, dispose of them immediately, taking care

not to touch the battery fluid. If the battery fluid comes into

contact with your eyes, mouth, or skin, rinse it off with water

immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

■ Using the remote as a wired remote

control

To use the remote control as a wired remote control, use a 2P

monaural miniplug to connect the remote control cable jack on the

underside of the remote control to the REMOTE IN jack on the

main unit.

Usable angle

30 degrees

Usable distance

7 m (23 feet)

A left/right arc of 30 degrees A vertical arc of 30 degrees

DVI

INPUT B

RGB/YP

/YC

D4 VIDEO G/Y B/P

R/P

INPUT A

HD/SYNC VD

OUT IN

REMOTE

RS-232C

S-VIDEO VIDEO

TRIGGER OUT

RESET

123

VIDEO

STILL HIDE

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

BD4

S VIDEO

INPUT

MEMORY

DVI

RESET

123

VIDEO

STILL HIDE

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

BD4

S VIDEO

INPUT

MEMORY

DVI

7 m

(23 feet)

7 m (23 feet)

RES

S VIDEO

INPUT

IRIS

ATT

. P

OOM

FOCUS

ID-1

ID-2

DVI

INPUT B

RGB/YP

/YC

D4 VIDEO G/Y B/P

R/P

INPUT A

HD/SYNC VD

OUT IN

REMOTE

RS-232C

S-VIDEO VIDEO

TRIGGER OUT

101_DPX-1000(E)01-05 03.2.19, 11:59 AM5

E-6

Installation

■ Installation methods

There are four ways to install this unit:

on a table in front of the screen.

mounted on the ceiling in front of the screen.

on a table behind a semi translucent screen.

mounted on the ceiling behind a semi translucent screen.

Set the method you use on the 4 <SETUP> section of the MENU described later. (see page 21.)

Place the unit on a standard height table to project and view the image

from in front of the screen. The height from the bottom of the unit to the

center of the lens is 12.4 cm (4”-7/8).

There are two kinds of brackets (low ceiling and high ceiling, sold

separately) available which can be used to mount the unit on the ceiling.

Consult your dealer for details on their use, and have installation done by

either your dealer or a reputable contractor.

The image on the screen is vertically reversed compared to that of a table

mounted installation. In this case, please set the installation type to

FRONT/CEILING in the 4 <SETUP> section of the menu. (see page

21.)

In this case, images are projected onto a semi translucent screen, and the

viewer watches it from the reverse side. The relationship with the screen

and projection distance corresponds to that for front projection. For rear

projection, set the installation type to REAR/CEILING or REAR/TABLE

in the 4 <SETUP> section of the menu. (see page 21.)

102_DPX-1000(E)06-08 03.2.19, 12:03 PM6

E-7

English

INSTALLATION

■ Screen and projection distance

The ideal position for mounting the main unit (Projection distance [a]) depends on the size of the screen to be used (the length of a diagonal

line across the screen). It is possible to adjust the projection distance within a preset range from Wide to Tele using the zoom function.

Additionally, it is possible to adjust the V. POS (Vertical positioning) of the image to better suit the screen. Use the information illustrated in

the figure below to determine the best position for installation.

Installation

Screen size

100

110

120

150

200

Wide (m) — Tele (m)

1.8 — 2.88

2.1 — 3.36

2.4 — 3.84

2.7 — 4.32

3.0 — 4.8

3.3 — 5.28

3.6 — 5.76

4.5 — 7.2

6.0 — 9.6

Since the DPX-1000 is equipped with a 16:9 element, the ideal

installation position for viewing images with a 4:3 screen depends

on the size of the desired image projection.

1 When a standard 16:9 image completely fills the width of the

screen (leaving black line at the top and bottom of the screen)

2 When the standard 4:3 image completely fills the screen

Screen size

100

120

200

Wide — Tele

(m), (feet, inches)

1.65 m — 2.64 m

5’5” — 8’8”

2.2 m — 3.52 m

7’2” — 11’7”

2.75 m — 4.4 m

9’ — 14’5”

3.3 m — 5.28 m

10’10” — 17’4”

5.5 m — 8.8 m

18’ — 28’10”

Projection distance

Wide — Tele

(m), (feet, inches)

2.2 m — 3.52 m

7’3” — 11’7”

2.9 m — 4.64 m

9’6” — 15’3”

3.65 m — 5.84 m

12’ — 19’2”

4.4 m — 7.04 m

14’5” — 23’1”

7.3 m — 11.68 m

23’11” — 38’4”

3 Projecting both 16:9 and 4:3 images

It is possible to use the zoom function to make use of the

screen efficiently for both 1 and 2 above. The projection

distance in this case will be between Wide in 2 and Tele in 1.

Adjust the size of the projected image using the zoom so that

all images fill the screen completely. However, please be aware

that adjustments to V. POS can cause the position of the image

to slip.

60'' 80'' 100'' 150'' 200''

6.0 – 9.6 m

(19'8" – 31'6")

4.5 – 7.2 m

(14'9" – 23'7")

3.0 – 4.8 m

(9'10" – 15'9")

2.4 – 3.84 m

(7'10" – 12'7")

1.8 – 2.88 m

(5'11" – 9'5")

For a 16:9 screen

*These are theoretical numerical values.

Please be aware that there may be some discrepancy in comparison to actual values.

Lens center line

Screen size

Projection distance [a]

(feet, inches)

5’11” — 9’5”

6’10” — 11’

7’10” — 12’7”

8’10” — 14’2”

9’10” — 15’9”

10’10” — 17’4”

11’10” — 18’11”

14’9” — 23’7”

19’8” — 31’6”

Projection distance [a]

102_DPX-1000(E)06-08 03.2.19, 12:03 PM7

E-8

Installation

■ Projection image position

Follow the instructions below to adjust the position of the projected image on the screen.

This figure shows the limits within which the zoom function can alter

projection distance in relation to the screen size. Within these limits, it is

possible to adjust the image so that it fills the screen completely. (See

page 12.)

It is possible to adjust the vertical position of the projected image on the

screen up or down by half the height of the screen.

For example, shifting V. POS fully up will bring the lower limit of the

image above the centerline of the lens. (See page 12.)

When this unit is mounted on a tabletop, the position of the image can be

adjusted by using the adjusters located on the underside of the unit.

Adjust the height by rotating the movable part of the two screw-type

adjusters at the front bottom of the case. The adjustment range of these

adjusters is 3 cm (1-1/4 inch). Adjust with care as loosening them further

may cause them to separate from the main unit.

■ Keystone

When the unit is mounted at an angle to the screen, the image will be projected in a trapezoid manner. Use the keystone function in the

keystone section of 4 <SETUP> in the menu to rectify this. (See page 21.)

Tele

Lens center line

Shifted fully down

Shifted fully up

Lens center line

Projected image

Wide

102_DPX-1000(E)06-08 03.2.19, 12:03 PM8

E-9

CONNECTIONS

English

DVI

INPUT B

RGB/YP

/YC

D4 VIDEO G/Y B/P

R/P

INPUT A

HD/SYNC VD

OUT IN

REMOTE

RS-232C

S-VIDEO VIDEO

TRIGGER OUT

◆ Note ◆

• Make sure to match the Y/PB/PR or Y/CB/CR of the A/V component and this unit when connecting a component to INPUT A compo-

nent jacks. Also, refer to the operation instructions for the A/V component. HD/SYNC and VD need to be connected for RGB video

signals in some cases.

Connecting the unit

• Make sure that the power of this unit and all other components is turned off before making any connections.

• Some components have different connection methods and connector names.

Refer to the operating instructions for each component that you wish to connect.

• Plug the unit in correctly to prevent it from creating noise or other problems.

■ Connecting A/V components

As shown in the illustration below, there are 6 types of connections provided on this unit for connection to A/V components.

Follow the instructions on the figure below to connect A/V video outputs from other components to this unit using the correct cables and

adapters.

D connector cable

D-sub monitor

cable

BNC cable for component

connection

Pin/BNC

adapters

Pin cable

Video pin cable

S video cable

D1—4 output

connectors

Pin jacksD-sub

Component/RGB video output connectors

Image output from A/ V components

BNC jacks S video output

jack

Video output

jack

Input

VIDEO

S-VIDEO

INPUT A

INPUT B

D4 VIDEO

DVI

Signal type

Composite video

S video

Component video/RGB video

Component video

Component video/RGB video (digital)

Connector type

Pin jack

Mini DIN connector

BNC connector x 3—5

D-sub 15 pin

D connector

DVI connector

DVI cable (digital)

DVI output

connector

103_DPX-1000(E)09-10 03.2.19, 12:05 PM9

E-10

DVI

INPUT B

RGB/YP

/YC

D4 VIDEO G/Y B/P

R/P

INPUT A

HD/SYNC VD

OUT IN

REMOTE

RS-232C

S-VIDEO VIDEO

TRIGGER OUT

■ Connecting to a computer

There are three ways of connecting a computer, as listed below. Please use the correct type of cable for the connector when making

connections.

Connecting the unit

◆ Note ◆

• Refer to see 2 <SIGNAL> in the menu described on page 19 for detailed settings for the type of image signal input.

DVI cable (Digital)

D-Sub monitor

cable

BNC monitor cable

Monitor output terminal

DVI output terminal

Computer

Input

INPUT A

INPUT B

DVI

Signal type

RGB Analog

RGB Digital

Connector type

BNC jack x 5

D-sub 15 pin

DVI connector

103_DPX-1000(E)09-10 03.2.19, 12:05 PM10

E-11

BASIC OPERATION

English

Basic Operations

■ Turning on the power

Be sure to remove the lens cover before using this unit.

1. Plug the supplied power cord into the AC inlet on the

rear of the DPX-1000, then plug the cord into the wall

outlet. The STANDBY/ON indicator will turn orange.

2. Press the STANDBY/ON button (The button on

the remote control). The indicator will blink green and

the lamp inside the unit will light up, in preparation

for projection.

◆ Note ◆

• There are STANDBY/ON indicators located on the front panel

and the control panel of the main unit.

3. After approximately 35 seconds, the indicator will

stop blinking, indicating that preparations for

projection are complete.

Important

• Be sure not to disconnect the power cord while the

power STANDBY/ON indicator is green, or blinking

green. This can cause significant damage to the

lamp and may result in a shorter lamp life or failure.

STANDBY/ON indicator

DVI

INPUT B

RGB/YP

/YC

D4 VIDEO G/Y B/P

R/P

INPUT A

HD/SYNC VD

OUT IN

REMOTE

RS-232C

S-VIDEO VIDEO

TRIGGER OUT

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

STANDBY/ON indicator

AC inlet

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

STANDBY ON ( )

■ Turning off the power

1. Press the STANDBY/ON button when finished using

this unit.

There will be a message to confirm that you wish to turn the

unit off. Press the STANDBY/ON button once more to confirm

that you wish to do so. The lamp will switch to a half-lit state,

and the fan continues for roughly 2 minutes to cool the lamp.

During this time, the STANDBY/ON indicator blinks orange.

You cannot turn the unit on again by pressing the STANDBY/

ON button during this time.

◆ Note ◆

• The lamp may blink when in the half-lit state. This is not a

lamp failure.

2. Once cooling is completed, the STANDBY/ON

indicator will cease blinking, becoming a steady

orange.

Important

• Do not disconnect the power cord when the fan is

going and the STANDBY/ON indicator is blinking

orange. This could damage the lamp and result in

shorter lamp life or lamp failure.

3. Replace the lens cover and disconnect the unit from

the power outlet if you do not plan to use it for a long

time.

Important

• Condensation may appear on the unit if the

temperature of the surround environment changes

quickly. Condensation may also cause the

projected image to be cloudy. Switch off the unit

power until the condensation disappears.

Switching the unit on when condensation is

present may damage the unit.

Press again for standby

This section describes the basic operation of the DPX-1000 once installation and connection have been completed. It is necessary to make

detailed settings in the menu described later so that the DPX-1000 is correctly set for the mounting, screen, input signals, and other

conditions of its installation. Follow the steps described in this section to carry out these procedures.

104_DPX-1000(E)11-15 03.2.19, 12:07 PM11

E-12

Basic Operations

■ Preparations for projection

Carry out the adjustments necessary to the projection image to

obtain the optimum setting for projection.

The initial setting on this unit is for projection of the image in a

line directly from the center of the lens. Where the center of the

screen is above or below the center of this line, use the V. POS

function to adjust the vertical position of the image up or down.

V. POS can adjust the image up to half the height of the screen.

1. Press the V. POS button on the remote control or the

SETTING button on the main unit repeatedly to place

the unit in vertical position adjustment (Lens shift)

mode.

2. Adjust the image to a suitable position by pressing

either the h or g buttons.

3. Press the V. POS button again or the ESCAPE button

to exit from the vertical position adjustment mode.

Enlarge or reduce the size of the image to fit the size of the screen.

The maximum extent of this zoom is 1:1.6.

1. Press the ZOOM button on the remote control or the

SETTING button on the main unit repeatedly to place

the unit in zoom adjustment (Zoom) mode.

2. Adjust the image to a suitable size by pressing either

the h or g buttons.

3. Press the ZOOM button again or the ESCAPE button

to exit from the adjustment mode.

Adjust the focus of the projected image.

1. Press the PATT button on the remote control or the

PATTERN button on the main unit to display a test

pattern for adjustment.

2. Press the FOCUS button on the remote control or the

SETTING button on the main unit repeatedly to place

the unit in focus adjustment mode.

3. Adjust the unit to an optimal focus setting by

pressing either the h or g buttons.

4. Press the FOCUS button again or the ESCAPE button

to exit from the focus adjustment (Focus) mode.

This unit is equipped with an IRIS function to switch between the

high levels of black and high contrast images important in a home

theatre and the bright images needed for a large screen. Use this

function as best suits your needs.

1. Press the IRIS button on the remote control or the

SETTING button on the main unit repeatedly to place

the unit in iris diaphragm adjustment (Iris) mode.

2. Adjust the unit to an optimal iris setting by pressing

either the + or – buttons.

3. Press the IRIS button again or the ESCAPE button to

exit from the iris adjustment mode.

This unit is equipped with three test patterns: a crosshatch pattern

useful for focus adjustment, and gray scale and color bar patterns

for image adjustment. Use them as best suits your needs.

1. Press the PATT button on the remote control or the

PATTERN button on the main unit to display a test

pattern for adjustment.

2. Select a suitable test pattern by pressing either the +

or – buttons.

3. Press the PATT button again or the PATTERN button

on the main unit to exit from the adjustment mode.

INPUT

AUTO

SETTING

ASPECT

ESCAPE

PATTIRIS

ZOOM FOCUSV. POS

PATTIRIS

FOCUS

V. POS

ZOOM

ESCAPE

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

SETTING

ESCAPE

104_DPX-1000(E)11-15 03.2.19, 12:07 PM12

E-13

BASIC OPERATION

English

■ Select an input

Press the INPUT button to display the input selection menu on the

screen. Use the h and g to select a name from those on display and

then press the to confirm your choice.

The signal settings for INPUT A, INPUT B and DVI will not

change. To change them, press the + button to open the submenu,

use the cursor buttons to select a suitable source from Component/

RGB PC/RGB TV, and confirm the selection by pressing the

button. You can select the terminal name directly from the input

area on the remote control.

Basic Operations

Input source The image signal to project

VIDEO Composite video signals input from an A/V component to

the VIDEO jack

S-VIDEO S video signals input from an A/V component to the S

VIDEO jack

INPUT A <COMPONENT>

Component signals input to INPUT A (BNC jack)

RGB signals input from a computer to INPUT A (BNC

jack)

RGB signals input from an A/V component to INPUT A

(BNC jack)

INPUT B <COMPONENT>

Component signals input to the D-sub 15-pin connector

on INPUT B

RGB signals input from a computer to the D-sub 15-pin

connector on INPUT B

RGB signals input from a component to the D-sub 15-pin

connector on INPUT B

DVI <COMPONENT>

Digital component signals input from an A/V component

to the DVI connector

Digital RGB signals input from a computer to the DVI

connector

Digital RGB signals input from an A/V component to the

DVI connector

D4 VIDEO Component signals input from an A/V component to the

D4 video connector

INPUT area

RESET

123

VIDEO

STILL HIDE

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

BD4

S VIDEO

INPUT

MEMORY

DVI

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

INPUT

Input signal

VIDEO

S VIDEO

INPUT A

INPUT B

DVI

Component

RGB PC

RGB TV

Enter

◆ Note ◆

• Setting a laptop or notebook PC to display simultaneously

on its built in display and on an external monitor can cause

the image to be incorrectly displayed on the external

monitor. In this case, set the PC to display on the external

monitor only. Refer to the computer’s operating instructions

for further details.

104_DPX-1000(E)11-15 03.2.19, 12:07 PM13

E-14

Basic Operations

■ Select a display aspect

Display aspect selects the type of image to display for an input signal.

Press

the ASPECT button and select a suitable mode. The types of

aspect mode available depend on the input signal. Additionally, this unit has an auto mode that can automatically select the correct display

aspect if the relevant information is encoded in the input signal. These modes are accessible from the display aspect area of the 2 <SIGNAL>

section of the menu described later.

1 Auto (Zoom)

In this mode, when the input signal is letterbox or squeeze

type, and such information is encoded in the input signal, the

unit will detect this and automatically change to the most

appropriate display aspect.

2 Normal

In this mode, the aspect from the input signal is kept as is, and

the image is projected vertically with an aspect of 16:9, filling

the screen and leaving a black area to the left and right of the

image.

3 Squeeze

This mode displays images that have been compressed

horizontally in a normal wide aspect manner.

4 Smart Zoom

This mode stretches the left and right edges of a 4:3 image

without altering the center, to project a 16:9 image which fills

the screen.

5 Zoom

This mode projects images received in a letterbox format in a

16:9 format that completely fills the screen.

6 Subtitle Zoom

This mode is the most appropriate for showing subtitled letter

box format video software. There are more detailed settings for

this mode, which can be adjusted in the Subtitle Zoom area of

the 2 <SIGNAL> section of the menu. Refer to page 24 for

details.

• Subtitle Area

Adjust the settings for subtitles.

• V Scroll

Adjust the position of the subtitles by moving the screen

vertically.

7 Through

This mode displays the signal as it is input with no enlargement

or reduction. The projected image size will vary according to

the resolution of the signal.

8 Through Squeeze

This mode expands the width of the input signal to display the

image in a 16:9 aspect. The projected image size will vary

according to the resolution of the signal.

[Representative examples]

Input signal type

Standard 4:3 image

Letter box

Squeeze

(Vista size)

Squeeze

(Cinemascope size)

HDTV

RGB PC

Input image Display aspect

Normal

Smart Zoom

Zoom

Subtitle Zoom

Squeeze

Through Squeeze

Squeeze

Normal

Projected image

SUBTITLE

104_DPX-1000(E)11-15 03.2.19, 12:07 PM14

E-15

BASIC OPERATION

English

Basic Operations

■ Other functions

STILL — freezing the image

Press the STILL button on the remote control to capture a frame

from a moving image. Press STILL once more to resume normal

projection.

HIDE — turning off the image temporarily

Press the HIDE button on the remote control to temporarily turn of

the projected image. Press the HIDE button once more to resume

normal projection.

■ Indicators

There are 5 indicators on the main unit that display the operating

status of the DPX-1000.

1 STANDBY/ON

(There is also an LED on the front panel of the

main unit.)

Off The power is turned off.

Steady orange Standby mode

Blinking green Startup mode

Steady green Operating

Blinking orange Lamp cooling prior to going into Standby

mode

Blinking red or red One of the LAMP/COVER/TEMP/FAN

and orange lights is also red.

Consult a YAMAHA dealer or service

center if this occurs.

2 LAMP

Off Normal

Blinking orange Lamp usage has exceeded 2000 hours.

Steady red The lamp has burnt out.

3 COVER

Off Normal

Steady red Either the lamp cover or the filter cover is

not correctly attached.

4 TEMP

Off Normal

Steady red Either the internal temperature of the unit

or the temperature of the lamp is

abnormally high.

5 FAN

Off Normal

Steady red The cooling fan is not working properly.

RESET

123

VIDEO

STILL HIDE

INPUT

ASPECT

LIGHT

BD4

S VIDEO

INPUT

MEMORY

DVI

STILL

RESET

123

VIDEO

STILL HIDE

INPUT

ASPECT

LIGHT

BD4

S VIDEO

INPUT

MEMORY

DVI

HIDE

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

104_DPX-1000(E)11-15 03.2.20, 2:07 PM15

E-16

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Move Menu Window

Image

Black Level

Off L ML MH H

A B C D E

Memory 1 VIDEO

White Level 0

Gamma Trim

Hue 0

Saturation 100

Color Temp.

Sharpness Type

Sharpness Gain

Level Adjustment

Iris

Color Balance

Signal Initial Setup

6000K

–

0.000uv

Standard

hgStandard Cinema

Location

Keystone

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

White Boost

Economy Mode

Menu Color

Message

Trigger Out

Baud Rate

Menu structure

1 <IMAGE>

These menu items make adjustments

to the projection image. The menu

details will vary depending on the

input signal type.

2 <SIGNAL>

These menu items set parameters for

the various input signals. The menu

details will vary depending on the

input signal type.

3 <INITIAL>

These menu items set the initial

parameters for a number of menu

items.

4 <SETUP>

These menu items set parameters

related to installation method,

remote control and so on.

Black Level (Brightness)

White Level (Contrast)

Gamma Trim

Hue

Saturation

Color Temp.

Sharpness Type

Sharpness Gain

Color Balance

Level Adjustment

Iris

Display Aspect

3D Y/C Separation

Noise Reduction

Video Type

Progressive Mode

Color Space Conversion

Setup Level (SDTV)

Setup Level (HDTV)

Signal Level

Sync Adjustment

Tracking

Horiz. Display Position

Vert. Display Position

Signal Status

Color System

INPUT A Signal

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

DVI Signal

Auto Power Off

Auto Input Search

Display Language

Lamp Running Time

Reset

Menu Start Screen

Menu Item

Menu Group

Items with a submenu

It is necessary to set various properties on a variety of menus so that this unit can project in optimal condition. There are four menu groups,

each with a number of different menu items. Some of these items are not selectable for certain types of input signal, some have submenus

attached, and others have a three stage menu hierarchy. (Displayed with a

overleaf.)

Each menu group consists of the items below. Follow the procedures outlined to adjust the parameters in each menu to suit your viewing

requirements.

105_DPX-1000(E)16-21 03.2.19, 12:08 PM16

E-17

English

Menu Item

BLACK LEVEL

Adjusts the level of blackness in an image while maintaining peak white brightness. Increasing

the black level will increase the luminosity of dark scenes and clarify picture tone, however it

will also lower the contrast. Reducing the black level will increase the contrast in dark scenes

but will reduce the clarity of black tones.

WHITE LEVEL (*CONTRAST)

Increases the level of whiteness in an image without changing the luminosity of the darker parts

of the image. Increasing the white level will brighten the white areas of an image and increase

contrast, however it will also reduce the clarity of white within the image. Reducing the white

level will lower contrast.

(*BRIGHTNESS)

Controls the total brightness of an image. When set too high, the black portion of the image

becomes grayish and the white portion of the image tends to be saturated. When set too low, the

entire image becomes darker.

GAMMA TRIM

Adjusts the response of the color gradation and gray scale within the image. There are ten

patterns available, on two pages of five patterns each. Use the key to switch between the

pages, and select the appropriate pattern for the contents to be viewed.

HUE

Adjusts the hue of the image. Reducing this setting increases the amount of red in the image.

Increasing it will add blue to the image.

SATURATION

Adjusts color depth. Reducing the value of this setting lightens the color of the image, while

increasing it will increase the depth of color.

COLOR TEMP.

Adjusts the level of white in colors between red and blue, and between green and magenta. A

lower setting adds more red to the colors giving a more relaxed feel to the image, while a higher

setting adds more blue, resulting in “fresh” color tones. Also, increase the hUV to give more

green to the image, or reduce it to add more magenta.

Adjustment range

–100 to 0 to +100

(*0.50 to 1.00 to 1.50)

–100 to 0 to +100

A/B/C/D/E

a/b/c/d/e

–100 to 0 to +100

0 to 100 to 200

5000K to 6000K

to 10000K

(COLOR TEMP.)

–0.020UV to ±0.000 to

+0.020UV (hUV)

■ 1 <IMAGE> ........ You cannot adjust these settings without an input signal.

Input signal

Video/Component,

RGB TV

Video/Component,

RGB TV, *RGB PC

*RGB PC

Video/Component,

RGB TV, RGB PC

Video/Component,

RGB TV

Video/Component,

RGB TV

Video/Component,

RGB TV, RGB PC

–

COLOR TEMP. ADJUSTMENT

Color temp. adjustment

Menu structure

BLACK LEVEL

White White

Output image

Black

BlackWhite White

Input signal Input signal

WHITE LEVEL

(*CONTRAST)

White

Black White

Input signal

(*BRIGHTNESS)

hUV

105_DPX-1000(E)16-21 03.2.19, 12:08 PM17

E-18

Adjustment range

OFF/L/ML/MH/H

0 to 16 to 63

STANDARD/RGB/

RGBYCM

–50 to 0 to +50

STANDARD/CINEMA

Input signal

Video/Component,

RGB TV

Video/Component,

RGB TV

Video/Component,

RGB TV, RGB PC

Component,

RGB TV, RGB PC

Video/Component,

RGB TV, RGB PC

Menu Item

SHARPNESS TYPE

Use this parameter to change the filtering characteristics of the circuitry used to sharpen edges

in the projected image.

SHARPNESS GAIN

Adjusts the clearness of the image edges. The higher value creates clearer edges. The lower

value creates a softer image with less noise element.

COLOR BALANCE

The default setting displays a good balance of colors, which you cannot change. For RGB, this

parameter adjusts the color balance and gain for the three primary colors R (red), G (green), and

B (Blue). The intermediate colors Y (yellow), C (cyan), and M (magenta) are set automatically

based on the RGB and color temperature settings. From the RGB submenu, press the RESET

key on the remote control to automatically adjust the RGB setting and based on the color gain

and temperature you have just set. For RGBYCM, you should set the color balance and gain for

each color separately. From the RGBYCM submenu, press the RESET key on the remote

control to automatically adjust the RGB or YCM tone and based on the color gain and

temperature you have just set. Refer to the color chart below for further help in adjusting

parameters.

You can change the background color to black by pressing the key when setting the COLOR

COORDINATE.

LEVEL ADJUSTMENT

Adjusts gain and offset for all parameters (Y, C

, C

/R, G, B) of component and RGB signals.

(except DVI input)

IRIS

IRIS set this parameter to STANDARD for viewing bright images on a large screen. Set it to

CINEMA if you want to give priority to the deep blacks and high contrast important to home

theatre viewing.

XYZ color system color chart

Menu structure

Green

Red

Cyan

Yellow

Magenta

Blue

105_DPX-1000(E)16-21 03.2.19, 12:08 PM18

E-19

English

Menu structure

Selections

AUTO/NORMAL/

SQUEEZE/SMART

ZOOM/ZOOM/

SUBTITLE ZOOM

(SUBTITLE AREA,

V SCROLL)

THROUGH

THROUGH SQUEEZE

0 to 3 to 10

–10 to 4 to +10

OFF/ON

OFF/1/2/3

DVD/VCR

AUTO/VIDEO

AUTO/SDTV/HDTV

0%/7.5%

16–235/0–255

–128 to 0 to +127

0 to 16 to 31

–50 to 0 to +50

Input signal

Video/Component,

RGB TV, RGB PC

Video(NTSC)

Video/Component,

RGB TV

Video

Video/Component,

RGB TV

Video/Component

Video/Component,

RGB TV

Component, RGB TV

RGB TV

*RGB PC

Video/Component,

RGB TV, RGB PC

■ 2 <SIGNAL> ...... You cannot adjust the parameters below if the unit is not receiving an input signal.

100

IMAGE SIGNAL

BLACK LEVELPEDESTAL LEVEL

Menu Item

DISPLAY ASPECT

Sets the aspect ratio to use when projecting an image for a given input signal. Under AUTO

mode, the unit will automatically switch to the most suitable mode for display. NORMAL

(THROUGH) mode projects the image as is without an alteration to the signal. SQUEEZE

displays horizontally compressed images in a normal non-compressed manner. ZOOM projects

the image scaled up by a given ratio. SMART ZOOM expands a 4:3 image to 16:9 size.

SUBTITLE ZOOM displays subtitles. THROUGH SQUEEZE displays an image with the width

scaled up. The availability of these options depends on the type of input signal.

Depending on the state of the input source, it may not be possible for the unit to automatically

select the optimal display mode. In this case, please select an appropriate mode manually.

SUBTITLE ZOOM contains the following parameter settings:

SUBTITLE AREA: Adjusts the subtitle display area

V SCROLL: Adjusts the vertical position of subtitles

3D Y/C SEPARATION

Suppresses the rainbow like color crossing and annoying dots in the image received from video

input. This choice is only available for NTSC format signals from composite inputs.

NOISE REDUCTION

Uses digital processing to eliminate noise in the luminance and color signals in sources with a

comparatively large amount of noise, producing a more vivid image. Use where warranted by

source quality.

VIDEO TYPE

To ensure synchronization, select VCR when using analog videotape as a video input source.

Select DVD for other sources.

PROGRESSIVE MODE

Switches the mode of interlace/progressive (I/P) conversion for the built in Faroudja function.

AUTO distinguishes film source automatically and projects it progressively at 60 frames per

second. Video turns the distinction function off. Both of these modes use the DCDi function.

(Only for SDTV interlaced signals)

COLOR SPACE CONVERSION

Selects color space coefficients for SDTV BT.601 and HDTV BT.709 type signals. In the AUTO

mode, the unit will automatically select an appropriate mode based on the resolution of the

signal.

SETUP LEVEL (SDTV)

Compensates for the differences in blackness levels

in normal image signals. It sets the level for signals

equal to the pedestal level at 0%, and those for

signals with high levels of blackness at 7.5%.

SETUP LEVEL (HDTV)

Compensates for the differences in blackness levels

in HDTV signals. It sets the level for signals equal to

the pedestal level at 0%, and those for signals with

high levels of blackness at 7.5%.

SIGNAL LEVEL

The function to change the range of the digital signal level of the input image.

Use 16—235 for a standard STB (Set Top Box) connection, or use 0—255 for a PC compatible

connection. (Only for DVI Signals)

SYNC ADJUSTMENT

Regulates flickering, noise, and disorder in the projection image. (* except DVI input)

TRACKING

Regulates vertical striping in the image. (* except DVI input)

HORIZ. DISPLAY POSITION

Adjusts the horizontal positioning of the projection image. (* except DVI input)

VERT. DISPLAY POSITION

Adjusts the vertical position of the projection image. (* except DVI input)

SIGNAL STATUS

Displays the resolution of the input signal, and synchronization information for RGB signals.

105_DPX-1000(E)16-21 03.2.19, 12:08 PM19

E-20

Menu structure

■ 3 <INITIAL>

INPUT A ➞ INPUT B ➞ D4 VIDEO ➞ S VIDEO ➞ VIDEO ➞ DVI

Menu item

COLOR SYSTEM

Selects the color system to use when the input signal is from a video source. Available selections are

NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, and SECAM. Usually, setting the unit to AUTO will

result in the unit automatically selecting the appropriate color method. However, since the unit does not

automatically detect NTSC4.43 under AUTO mode, set the color method to NTSC4.43 manually to view

NTSC4.43 images.

INPUT A SIGNAL

Selects the type of input signal received at INPUT A.

INPUT A SYNC TYPE

Selects the sync mode of the input signal received from INPUT A. (For RGB TV only)

INPUT B SIGNAL

Selects the type of input signal received at INPUT B.

INPUT B SYNC TYPE

Selects the sync mode of the input signal received from INPUT B. (For RGB TV only)

DVI SIGNAL

Selects the type of input signal received at DVI.

AUTO POWER OFF

Setting the power saving mode to ON will cause the unit to automatically turn off the lamp and place

itself in the standby mode if no signal is received through the inputs on the main unit for 30 minutes.

AUTO INPUT SEARCH

This function changes the input signal as shown below when the unit is not receiving a signal at the

selected input, or is not receiving a signal at the input selected prior to turning the unit on.

DISPLAY LANGUAGE

Selects the language to use in the menu display.

LAMP RUNNING TIME

Displays the total lamp running time. You can reset the lamp running time in the submenu attached to

this menu item.

RESET

Resets all parameters on the menu and held in memory to their default factory settings.

Selections

AUTO/NTSC/NTSC4.43/PAL/PAL-M/

PAL-N/PAL60/SECAM

COMPONENT/RGB PC/RGB TV

AUTO/Separate Sync/Composite Sync/

Sync on Green

COMPONENT/RGB PC/RGB TV

AUTO/Separate Sync/Composite Sync/

Sync on Green

COMPONENT/RGB PC/RGB TV

OFF/ON

/English/Deutsch/Español/Français/

Italiano/Portuguêsa/ /

ALL SETTINGS/ALL MEMORIES/

CURRENT MEMORY

105_DPX-1000(E)16-21 03.2.19, 12:08 PM20

E-21

English

Menu structure

■ 4 <SETUP>

Selections

FRONT/TABLE, FRONT/CEILING, REAR/

TABLE, REAR/CEILING

–100 to 0 to +100

FRONT&REAR/FRONT/REAR/OFF

ID 1/ID 2

OFF/ON

MONOTONE/COLOR

OFF/ON

LAMP/FAN/RS-232C

9600bps/19200bps/38400bps/57600bps/

115200bps

Increase the value in the positive (+) direction

When the upper part of the image is wider than the lower When the lower part of the image is wider than the top

Decrease the value in a negative (–) direction

Menu item

LOCATION

There are four ways of installing this unit; tabletop or ceiling mounting for front or rear projection. The

DPX-1000 will invert or rotate the projection according to this setting.

KEYSTONE

If the projection unit is at a horizontal or perpendicular angle to the screen the projection image will be

distorted to a trapezoid shape. Use the KEYSTONE setting to electronically correct without increasing

the length of the image. Increase the value when the top of the image is overly wide, and reduce the

value when the lower part of the image is too wide.

REMOTE CONTROL SENSOR

Use this parameter for switching between the 2 sensors located on the front and rear of the main unit that

receive signals from the remote control. You can operate the main unit with a wired remote regardless of

how this parameter is set.

REMOTE CONTROL ID

The main unit can receive commands from the remote control if you set the same ID in the main unit as

is set by the code change switch on the side of the remote control. Use this code change switch to allow

one remote to control two main units independently.

LENS ADJUSTMENT LOCK

Locks the lens so that the V. POS, ZOOM, and FOCUS settings cannot be changed accidentally. Set to

OFF to cancel this function.

WHITE BOOST

Enhances the luster of the white part in the projected image.

ECONOMY MODE

Lowers power supply to the lamp by approximately 20% to prolong its life.

MENU COLOR

Selects the color of the characters and background for the on-screen menu display. Press the + or

button to access the submenu and change color selections.

MESSAGE

Set whether to display messages of any type on screen.

TRIGGER OUT

Set the external control TRIGGER OUT terminal 12V signal emission to “LAMP” to synchronize it to

the ON/OFF state of the lamp, to “FAN” to synchronize it to the fan, and to “RS-232C”, to receive ON/

OFF signals through the RS-232C terminal.

BAUD RATE

Sets the transmission speed of the RS-232C terminal.

This setting becomes valid from the next time you switch the unit on.

105_DPX-1000(E)16-21 03.2.19, 12:08 PM21

E-22

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Move Menu Window

Image

Display Aspect

Memory 1 VIDEO

3D Y/C Separation

Noise Reduction

Video Type

Progressive Mode

Color Space Conversion

+: Enter

Initial Setup

Setup Level (SDTV)

Signal Status

Off On

DVD VCR

Auto

VideoAuto

0% 7.5%

Setup Level (HDTV) 0% 7.5%

1 2 3

Auto SDTV HDTV

Off

Signal

Auto

Normal

Squeeze

Smart Zoom

Zoom

Subtitle Zoom

Through

Through Squeeze

Display Aspect

Menu operation

■ Menu screen and operating buttons

This section provides you with general information about the menu screen and operating buttons on the remote control and this unit’s control

panel for easier operation. Please read it carefully before starting to operate the menu.

There are four menu groups in the menu, each containing various

menu items. Some menu items also have submenus, making up a 3

tier hierarchy.

MOVE MENU WINDOW

Menu group

Menu item

Help message

Memory setting

number

Input signal

Submenu

parameter

Submenu mark

Parameter

1 MENU button

Opens or closes the menu.

2 Cursor buttons

+/– (for side-to-side movements)

• Select a menu group.

• Open and close submenus.

• Select or change settings.

h/g (for up and down movements)

• Select a menu item.

• Select or change settings.

3 button

• Opens a submenu.

•

Confirm a new setting when adjusting “COLOR SYSTEM”,

“INPUT A SIGNAL”, “INPUT B SIGNAL”,

“DVI SIGNAL”, “LOCATION”, “REMOTE CONTROL

SENSOR”, or “REMOTE CONTROL ID”.

• Opens a one-touch image menu when the menu screen has

not been opened.

4 MEMORY buttons 1—6 (Remote control only)

Select a memory setting number.

5 ESCAPE button

• Returns the cursor to the menu group hierarchy from the

menu item hierarchy.

• Closes the submenu.

• Closes the menu when the cursor is on one of the menu

groups.

• Returns the cursor to the menu input screen after changing

menus.

6 RESET button (Remote control only)

Resets the parameter setting to the factory setting.

(Items without factory settings cannot be reset.)

RESET

123

VIDEO

STILL HIDE

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

BD4

S VIDEO

INPUT

MEMORY

DVI

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

106_DPX-1000(E)22-30 03.2.19, 12:09 PM22

E-23

English

Menu operation

■ Basic menu operation

To ensure proper projection, start with setting and adjustment in menu group “SETUP”.

RESET

123

VIDEO

STILL HIDE

INPUT

ASPECT

LIGHT

BD4

S VIDEO

INPUT

MEMORY

DVI

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

1, 6

3, 5

2, 4

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

1, 6

2, 4

3, 5

1. Press MENU to open the menu.

The previous menu screen opens if menu operations have

already been performed.

2. Press + or – to select a menu group.

3. Press g to enter the menu item hierarchy.

Then select an item to be adjusted by pressing the h or g

button.

4. Select or change the parameter by pressing + or –.

Remote control

Control panel

Remote control

Control panel

Remote control

Control panel

Remote control

Control panel

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Move Menu Window

Image

Black Level

Off L ML MH H

A B C D E

Memory 1 VIDEO

White Level 0

Gamma Trim

Hue 0

Saturation 100

Color Temp.

Sharpness Type

Sharpness Gain

Level Adjustment

Iris

Color Balance

Signal Initial Setup

6000K

–

0.000uv

Standard

Standard Cinema

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Memory 1 VIDEO

Setup

Location

Keystone 0

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Economy Mode

Off On

White Boost Off On

Off On

Front / Table

Front & Rear

ID 1

Move Menu Window

Image Signal Initial

MonotoneMenu Color

Off On

Trigger Out

Baud Rate 115200bps

LAMP

Message

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Memory 1 VIDEO

Setup

Location

Keystone 0

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Economy Mode

Off On

Front / Table

Front & Rear

ID 1

MonotoneMenu Color

Move Menu Window

Image Signal Initial

Off On

Trigger Out

Baud Rate 115200bps

LAMP

Message

White Boost Off On

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Memory 1 VIDEO

Setup

Location

Keystone 0

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Economy Mode

Off On

Front / Table

Front & Rear

ID 1

MonotoneMenu Color

Move Menu Window

Image Signal Initial

Off On

Trigger Out

Baud Rate 115200bps

LAMP

Message

White Boost Off On

106_DPX-1000(E)22-30 03.2.19, 12:09 PM23

E-24

Some items are adjusted by increasing or decreasing the value on

the scale, and others by selecting a number or a word.

Press the RESET button to reset the parameter to the factory

setting. (Items without a factory setting cannot be reset.)

5. Press h or g to move the cursor to the next item.

To set a menu item in another menu group, press the ESCAPE

or h button to return to the presently selected menu group, and

follow steps 2—4 described previously to continue with menu

setting.

6. Press MENU to close the menu when you have

completed any changes.

Menu operation

Operation group A: Press the + or button to open the

submenu. Select the desired parameter using the h or g buttons (h,

g, +, or – buttons for COLOR TEMP.), then press the ESCAPE

button to close the submenu.

*“SIGNAL STATUS” is a display-only message which does not

alter any parameters.

Operation group B: Press the + or

button to open the

submenu. Select the desired parameter using the h or g buttons,

and press the

button to confirm your setting. Press the

ESCAPE button to close the submenu.

Operation group C: Press the + or

button to open the

submenu. Select the desired parameter using the h or g buttons

and then use the + or – buttons to change the parameters. It is not

necessary to confirm the new setting.

Operation group D: Press the + or button to open the

submenu. This submenu is in the form of messages. Follow the on-

screen directions to adjust settings. The submenu for this group is

explained on pages 26 and 27.

—EXCEPTION—

Some submenu items have further submenus attached to them.

These items have “ ” displayed on the right. Press the button to

enter the detail menu, and select an appropriate setting using the

cursor keys.

Remote control

Control panel

Remote control

Control panel

■ Submenus

Following is a list of the menu items that have a submenu.

Submenu operation varies according to the menu item selected.

Follow the steps of the applicable submenu operation group.

Menu items with a submenu

Submenu operation

group

Menu group

IMAGE

SIGNAL

INITIAL

SETUP

Menu item

COLOR TEMP.

COLOR BALANCE

LEVEL ADJUSTMENT

DISPLAY ASPECT

SIGNAL STATUS

COLOR SYSTEM

INPUT A SIGNAL

INPUT A SYNC TYPE

INPUT B SIGNAL

INPUT B SYNC TYPE

DVI SIGNAL

DISPLAY LANGUAGE

LAMP RUNNING TIME

RESET

LOCATION

REMOTE CONTROL

SENSOR

REMOTE CONTROL ID

MENU COLOR

TRIGGER OUT

BAUD RATE

Gamma Trim

A B C D E

Black Level

106_DPX-1000(E)22-30 03.2.19, 12:09 PM24

E-25

English

3. Select the submenu parameter by pressing h or g.

Press the RESET button to reset the parameter to the factory

setting. (Items without a factory setting cannot be reset.)

The following step is necessary to set “COLOR SYSTEM”,

“INPUT A SIGNAL”, “INPUT B SIGNAL”, “DVI SIGNAL”

and “REMOTE CONTROL SENSOR” in operation group B.

[Operation group B only]

Press when setting is complete. This will confirm the new

setting close the submenu. Settings for the above items will not

be changed if not confirmed by the

button.

To reset the parameter to the factory setting, press the RESET

button when the submenu has been opened.

4. Press MENU to close the menu.

Press the ESCAPE or – button to return to the previous screen

and continue adjusting settings.

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

MEMORY 1 VIDEOESCAPE: Return

Normal

Squeeze

Move Menu Window

Image

Display Aspect

Initial Setup

Auto

Signal

Smart Zoom

Zoom

Subtitle Zoom

Through

Through Squeeze

Menu operation

■ Basic submenu operation

[Operation groups A and B]

1. Select the menu item to be adjusted by following

steps 1—3 in “Basic menu operation”.

The submenu mark “ ” appears on the right side of the item.

2. Press + or to open the submenu.

Remote control

Control panel

Remote control

Control panel

Remote control

Control panel

Remote control

Control panel

Move Menu Window

Image

Display Aspect

Memory 1 VIDEO

3D Y/C Separation

Noise Reduction

Video Type

Progressive Mode

Color Space Conversion

+: Enter

Initial Setup

Setup Level (SDTV)

Signal Status

Off On

DVD VCR

Auto

VideoAuto

0% 7.5%

Setup Level (HDTV) 0% 7.5%

1 2 3

Auto SDTV HDTV

Off

Signal

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

MEMORY 1 VIDEOESCAPE: Return

Normal

Squeeze

Move Menu Window

Image

Display Aspect

Initial Setup

Auto

Signal

Smart Zoom

Zoom

Subtitle Zoom

Through

Through Squeeze

106_DPX-1000(E)22-30 03.2.19, 12:09 PM25

E-26

● Submenu operation — “COLOR BALANCE”

[Operation group C]

1. Follow steps 1—3 in “Basic menu operation” to select

the menu item “COLOR BALANCE” in menu group

<IMAGE>.

The submenu mark “

” appears on the right side of the item.

2. To set “RGBYCM” parameters, select “RGBYCM” with

the g button, and press the + button or

to enter the

submenu.

3. Select the submenu item by pressing h or g.

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Move Menu Window

Image

Black Level

Off L ML MH H

A B C D E

Memory 1 VIDEO

White Level 0

Gamma Trim

Hue 0

Saturation 100

Color Temp.

Sharpness Type

Sharpness Gain

Level Adjustment

Color Balance

+: Enter

Signal Initial Setup

6000K

–

0.000uv

Standard

Iris Standard Cinema

Menu operation

4. Use h, g, +, and – to set the gauge figures to your

liking.

Press the RESET button to reset the parameter to the factory

setting.

5. Press MENU to close the menu.

To continue adjusting settings, press the ESCAPE button to

return to the previous screen. Pressing the – button will not

close the submenu.

● Submenu operation — resetting “LAMP

RUNNING TIME”

[Operation group D]

1. Select the menu item “LAMP RUNNING TIME” in the

menu group “INITIAL” by following steps 1—3 in

“Basic menu operation”.

The submenu mark “

” appears on the right side of the item.

2. Press + or to open the confirmation message

screen.

Move Menu Window

Image

Memory 1 VIDEO+: Enter

Signal Initial Setup

Color Balance Standard

RGB

RGBYCM

Move Menu Window

Image

Memory 1 VIDEOESCAPE: Return

Signal Initial Setup

R Color Coordinate

R Gain 0.96

x=0.640 y=0.330

G Color Coordinate

G Gain 0.69

x=0.300 y=0.600

B Color Coordinate

B Gain 0.43

x=0.150 y=0.060

Y Color Coordinate

Y Gain 0.95

x=0.428 y=0.499

C Color Coordinate

C Gain 0.68

x=0.226 y=0.332

M Color Coordinate

M Gain 1.00

x=0.336 y=0.163

Move Menu Window

Image

Memory 1 VIDEO

Signal Initial Setup

R Color Coordinate

R Gain 1.20

x=0.640 y=0.330

ESCAPE: Return

G Color Coordinate

G Gain 0.69

x=0.300 y=0.600

B Color Coordinate

B Gain 0.43

x=0.150 y=0.060

Y Color Coordinate

Y Gain 0.95

x=0.428 y=0.499

C Color Coordinate

C Gain 0.68

x=0.226 y=0.332

M Color Coordinate

M Gain 1.00

x=0.336 y=0.163

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Color Sytem

Memory 1 VIDEO

INPUT A Signal

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

Auto Power Off

+: Enter

Auto Input Search

Display Language

Reset

Auto

Component

Auto

RGB PC

Auto

RGB PCDVI Signal

English

Lamp Running Time 0 Hour

OnOff

Off On

Setup

Move Menu Window

Image Signal Initial

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Press " " to reset lamp running time.

Yes

Memory 1 VIDEO: Fix

Setup

Move Menu Window

Image Signal Initial

Lamp Running Time 0 Hour

106_DPX-1000(E)22-30 03.2.19, 12:09 PM26

E-27

English

3. Press h or g to select the submenu item to reset.

4. Press + or to open the confirmation message

screen.

5. Press to reset the parameter to its factory default

setting.

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

MEMORY 1 VIDEO+: Enter

Reset

All Settings

All Memories

Current Memory

Setup

Move Menu Window

Image Signal Initial

Menu operation

3. Select “YES” with h or g, and then press .

LAMP RUNNING TIME will reset to 0 hour.

4. Press the MENU button to close the menu.

● Submenu operation—“RESET”

[Operation group D]

1. Follow steps 1—3 in “Basic menu operations” to

select menu item “RESET” in menu group <INITIAL>.

The submenu mark “ ” appears on the right side of the item.

2. Press + or to open the submenu.

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Yes

Memory 1 VIDEO: Fix

Setup

Move Menu Window

Image Signal Initial

Lamp Running Time 0 Hour

Press " " to reset lamp running time.

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Color Sytem

Memory 1 VIDEO

INPUT A Signal

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

Auto Power Off

+: Enter

Auto Input Search

Display Language

Reset

Auto

Component

Auto

RGB PC

Auto

English

Lamp Running Time 0 Hour

OnOff

Off On

Setup

Move Menu Window

Image Signal Initial

RGB PCDVI Signal

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Memory 1 VIDEO+: Enter

Reset

All Settings

All Memories

Current Memory

Setup

Move Menu Window

Image Signal Initial

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Memory 1 VIDEOESCAPE: Return

Setup

Move Menu Window

Image Signal Initial

Press " " to reset

all memories.

106_DPX-1000(E)22-30 03.2.19, 12:09 PM27

E-28

■ Changing the menu location

Press ESCAPE or h to return the cursor to the menu

group.

2. Press h to enter the “MOVE MENU WINDOW”.

3. Press h, g, +, or – to change the display location.

4. Press ESCAPE to return to the menu after setting the

location.

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Memory 1 VIDEO

Setup

Location

Keystone 0

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Economy Mode

Off On

White Boost Off On

Off On

Front / Table

Front & Rear

ID 1

Move Menu Window

Image Signal Initial

MonotoneMenu Color

Off On

Trigger Out

Baud Rate 115200bps

LAMP

Message

Menu operation

■ One-touch image menu

Press when the menu screen is not open.

Menu items appear one by one at the bottom of the screen. The

display will disappear if no operation is performed within five

seconds.

2. Press h or g to select a menu item to adjust.

3. Press + or – to select the desired value.

Press the RESET button to reset the parameter to the factory

setting.

4. Press ESCAPE to close the display.

Remote control

Control panel

ESCAPE

Remote control

Control panel

Remote control

Control panel

Remote control

Control panel

ESCAPE

Remote control

Control panel

Black Level

Remote control

Control panel

Remote control

Control panel

L ML MH H

Sharpness Type

Off

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Memory 1 VIDEOESCAPE: Return

Setup

Move Menu Window

Image Signal Initial

ESCAPE

Remote control

Control panel

Sharpness Type

Off L ML MH H

106_DPX-1000(E)22-30 03.2.19, 12:09 PM28

E-29

English

Memory function

This unit has a memory function able to store six settings for

projecting different types of input sources in the most appropriate

manner. Select the setting that is most appropriate for your

projection. Some settings may not be available depending on the

type of input signal currently in use. Six settings have been preset,

but each parameter can be changed and restored at will. The

following lists the menu items that you can store in memory.

■ Selecting the memory setting number

Using the remote control

Press the MEMORY button number with the desired setting.

(MEMORY BUTTON 1—6)

Using the menu

1. Press MENU to open the menu.

2. Press g to enter the memory setting number at the

bottom of the screen.

3. Press + to open the submenu.

4. Press h or g to select the number of the desired

memory setting number.

5. Press ESCAPE to close the submenu.

456

123

MEMORY

IMAGE

BLACK LEVEL (BRIGHTNESS)

WHITE LEVEL (CONTRAST)

GAMMA TRIM

SATURATION

HUE

COLOR TEMP.

SHARPNESS TYPE

SHARPNESS GAIN

COLOR BALANCE

LEVEL ADJUSTMENT

IRIS

SIGNAL

3D Y/C SEPARATION

VIDEO TYPE

PROGRESSIVE MODE

COLOR SPACE CONVERSION

SETUP LEVEL

SIGNAL LEVEL

ESCAPE

Move Menu Window

Image

Memory 1 VIDEO+: Enter

Initial SetupSignal

Display Aspect

3D Y/C Separation

Noise Reduction

Video Type

Progressive Mode

Color Space Conversion

Setup Level (SDTV)

Signal Status

Off On

DVD VCR

Auto

VideoAuto

0% 7.5%

Setup Level (HDTV) 0% 7.5%

1 2 3

Auto SDTV HDTV

Off

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Memory 5

Memory 4

Memory 3

Memory 2

Memory 1

Move Menu Window

Image

Memory 6 VIDEOESCAPE: Return

Initial SetupSignal

106_DPX-1000(E)22-30 03.2.19, 12:09 PM29

E-30

Memory function

To reset all parameters in all six memory settings

Follow the directions in “Submenu operation—RESET” on page

27 to select “ALL MEMORIES” on the submenu. Press the + or

buttons to open the confirmation message screen. Press the

button to reset to factory default settings.

■ Resetting to the factory default settings

For one parameter

Follow steps 1—3 in “Basic menu operation” on page 23 to select

the parameter to reset. Press the RESET button on the remote

control to return the parameter to its factory default setting. (Items

without a factory default cannot be reset.)

To reset all parameters for the currently selected

memory number

Follow the directions in “Submenu operation—RESET” on page

27 to select “CURRENT MEMORY” on the submenu. Press the +

or buttons to open the confirmation message screen. Press the

button to reset the selected memory area to its factory default

settings.

Remote control

Control panel

Remote control

Control panel

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Memory 1 VIDEOESCAPE: Return

Setup

Move Menu Window

Image Signal Initial

Press " " to reset current memory.

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg hg hg

Memory 1 VIDEOESCAPE: Return

Setup

Move Menu Window

Image Signal Initial

Press " " to reset

all memories.

106_DPX-1000(E)22-30 03.2.19, 12:09 PM30

E-31

English

ADDITIONAL

INFORMATION

AAAAA

■ Glossary

The following is a list of key words and their explanations used in

the use of projectors and image signals. Please refer to it when

using the DPX-1000.

DLP™ technology

This stands for Digital Light Processing. DLP uses the DMD

chip, developed by Texas Instruments.

DCDi™ function

This is an abbreviation of Directional Correlational

Deinterlacing, a high quality image circuitry developed by the

Faroudja company. It uses edge cutting techniques to remove

jagged edges from images during Interlace → Progressive

conversion, allowing smooth, natural image reproduction.

Component video signal

Component video signal is sent with independent luminance

and color signals. It gives a higher image quality than ordinary

composite video signal because it bypasses mixing and

separating circuits. Component video signal consists of three

lines, the luminance signal (Y) and two color difference signals

B/CB, PR/CR).

S video signal

S stands for Separate. This signal is sent with separated

luminance (Y) and color (C) signals. Use a 4-pin mini DIN

connector and cable for connection.

Composite video signal

This is the most common type of video signal. The luminance

signal and color signal are sent combined in one line. Mixing

and separating processes are necessary on both the send and

receive sides. A pin cable is used for connection.

RGB signal

An RGB signal transmits color information by using a numeric

representation of the primary colors of red, green and blue

separately. When the signal is received, it can be expressed in

various colors by adding and mixing colors. This type of signal

is widely used for sending and receiving color images between

computers. Horizontal and vertical sync signals are also

necessary.

HDTV

This is an abbreviation of High-Definition Television, a term

used to define systems that satisfy the following conditions:

• A vertical resolution of 720p, or 1080i (p stands for

progressive scans, i stands for interlace scans).

• An image aspect ratio of 16:9

SDTV

An abbreviation of Standard Definition Television, used to

define normal television broadcasts which do not meet the

standards of HDTV.

Additional information

D connector

This connector is designed for the Japanese D format only.

It is used for sending and receiving the image signal between

the latest type of A/V components. This connector can receive

the component signal by using a D connector cable. There are

five levels (D1—D5) of performance characteristics. This unit

is compatible with D1, 2, 3, and 4.

DVI connector

A digital RGB/Component signal is sent differentially from a

computer or A/V equipment to this connector. A 24-pin

connector and cable are used.

Standby

The state in which the circuit to receive infrared-signals from

the remote control is activated but other main circuits are

turned off. A small amount of power is consumed in this state.

Test pattern

Test patterns are stored in this unit for use in adjusting the

position and focus of the projected image on the screen.

Interlace

The most common type of scanning in use in televisions. It

divides an image into two fields for scanning, and uses even

and odd numbered lines of those fields to build an image

(frame).

Progressive

This displays all the scanning lines of the entire frame at one

time. It greatly reduces the flicker that is more noticeable on a

larger screen to create a sharp and smooth image. This unit

projects using progressive scanning.

3-2 Pulldown detection style IP conversion

A function for directly converting interlace signal into sixty

frame progressive signal used when receiving 60 field interlace

signal from an image source recorded with the same 24 frames

as movie film. This allows DVD and other materiel recorded

with 24 frames to be projected on large screens as a natural,

precise image with no loss of quality, comparable to a movie

film.

SYNC

Computers output signals with a given regular frequency,

which the projector must be synchronized to in order to

produce a good quality image. Failure to match the phase of the

signal will result in flickering, fading, and distortion of the

image.

TRACKING

Computers output signals with a given regular frequency,

which the projector must be synchronized to in order to

produce a good quality image. Failure to match signal

frequencies will result in vertical striping in the image.

• DLP™ and DMD™ are trademarks of Texas Instruments.

•

is a trademark of Faroudja, a division of Genesis

Microchip Inc.

107_DPX-1000(E)31-39 03.2.19, 12:11 PM31

E-32

HDCP

High-bandwidth Digital Content Protection system. HDCP is

designed to protect the video transmission between a DVI

transmitter and a display device.

Aspect

This refers to the length-to-width ratio of an image.

Ceiling mount bracket

This is the mounting hardware used to hand this unit from the

ceiling. Two types of bracket are available, for high and low

ceilings. Ceiling mount brackets are sold separately.

Keystone

If the unit is used at an angle to the screen the projected image

will be distorted in a trapezoid fashion. Keystone is used to

electronically correct this distortion.

Letter box

This is a method used to convert the content of a film in

landscape orientation to a 4:3 signal. It is possible to watch a

landscape image without trimming by adding a black bar to the

top and bottom of the screen, however this sacrifices vertical

resolution to some extent.

Squeeze

This method compresses a film image horizontally to an aspect

ratio of 4:3 when recording on a video medium. The squeezed

image must pass through a de-squeezing circuit in order to be

projected in it’s original form.

Smart Zoom

Smart zoom expands the left and right sides of a 4:3 image

without altering the center, when it is necessary to project a 4:3

image to a wide screen format. This creates some distortion at

both edges.

Vista size

A standard film size. The aspect ratio is 1.85:1 in North

America and 1.66:1 in Europe.

Cinema scope size

The widest film format in 70mm film. The aspect ratio is

2.35:1.

Color spacing

This refers to the conversion of YUV color separated signal to

RGB signal. There are two formats for this, SDTV BT.601 and

HDTV BT.709. This unit can switch between them as required.

Additional information

107_DPX-1000(E)31-39 03.2.19, 12:11 PM32

E-33

English

ADDITIONAL

INFORMATION

Additional information

■ Projectable signals

The following charts show the types and formats of the signals that can be projected by this unit. Any signals not listed below may not be

properly projected.

1. TV format 1 ------ Composite or S video signals sent to the VIDEO or S-VIDEO inputs

2. TV format 2 ------- Component or RGB TV signals sent to the INPUT A, B and DVI, or component signals sent to the D4, DVI input

connector

Type of signal

NTSC

PAL

SECAM

PAL60

NTSC

4.43

PAL-M

PAL-N

V active

(lines)

480

576

480

576

480

576

f (V)

(Hz)

59.94

50.00

59.94

50.00

fsc

(MHz)

3.58

4.43

4.406, 4.25

4.43

3.58

Color system

NTSC

PAL

SECAM

PAL

NTSC

PAL

Type of signal

480i*

576i*

480p

576p

720p/50Hz

720p/60Hz

1035i*

1080i/50Hz

1080i/60Hz

H active

(pixels)

720

1280

1920

V active

(lines)

483

576

480

576

720

1035

1080

f (H)

(kHz)

15.734

15.625

31.469

31.250

37.500

45.000

33.750

28.125

33.716

f (V)

(Hz)

59.940

50.000

59.940

50.000

59.940

60.000

50.000

59.940

f (V)

(Hz)

59.940

72.809

75.000

85.008

56.250

60.317

72.188

75.000

85.061

60.004

66.666

Type of signal

VGA/60Hz

VGA/72Hz

VGA/75Hz

VGA/85Hz

SVGA/56Hz

SVGA/60Hz

SVGA/72Hz

SVGA/75Hz

SVGA/85Hz

XGA/60Hz

Mac13”

H active

(pixels)

640

800

1024

640

V active

(lines)

480

600

768

480

(H)

(kHz)

31.469

37.861

37.500

43.269

35.156

37.879

48.077

46.875

53.674

48.363

35.000

VESA

Apple

• DVI digital component format supports YCBCR 4:4:4 (8 bit x 3) only.

* This unit does not support these signal types when using a DVI connection.

3. PC format 1 ------ Analog RGB PC signals sent to the INPUT A or B inputs

• VESA is trademark of Video Electronics Standards Association.

• Macintosh is a trademark of Apple Computer, Inc.

4. PC format 2 ------ Digital RGB signal input sent to the DVI input terminal

Depending on the computer you are using, projection may not be possible in this mode.

H active

(pixels)

640

800

1024

1280

V active

(lines)

480

600

768

720

(H)

(kHz)

31.469

37.879

48.363

45.000

(V)

(Hz)

59.940

60.317

60.004

59.940

VESA

Type of signal

VGA/60Hz

SVGA/60Hz

XGA/60Hz

1280x720/60Hz

107_DPX-1000(E)31-39 03.2.19, 12:11 PM33

E-34

Additional information

Message

No Signal

INPUT A (Component) (Example)

Out Of Range

Unknown Format

Auto Sync...

Memory 1—6

The lamp needs to be replaced. Please

replace the lamp you are currently

using with a new one.

Press again for standby.

Squeeze (Example)

Lens Adjustment is locked.

■ Message display

Condition

The unit is not receiving or detecting any signal at the selected input source. This message is displayed

together with the name of the input source selected with the INPUT button.

The input name selected by the INPUT button is displayed. It will turn off 1 minute after the signal has

been input.

The unit is not able to decode the PC signal currently being input.

The unit is not able to decode the video signal currently being input.

The unit is setting itself to the most appropriate configuration for the RGB signal currently being received.

The memory setting number is displayed for 2 seconds.

This message is displayed when the power switch is turned on if the lamp running time exceeds 2000 hours.

Press the ESCAPE key to remove the message.

Press the STANDBY/ON button once more to place the unit in standby mode.

The name of the display aspect mode selected with the ASPECT button is displayed for 2 seconds.

Displayed when the “LENS ADJUSTMENT LOCK” is set to “ON”. This message will display for 2

seconds if you press the V. POS, ZOOM, or FOCUS buttons when the “LENS ADJUSTMENT LOCK” is

set to “ON”.

107_DPX-1000(E)31-39 03.2.19, 12:11 PM34

E-35

English

ADDITIONAL

INFORMATION

Maintenance

■ Regular care

Be sure to disconnect the power cable prior to doing any maintenance.

Wipe with a soft cloth. Use a damp cloth with a mild detergent and

then wipe with a dry cloth again if the unit is heavily soiled. Do not

use strong solvents such as thinner or alcohol as they may damage

the case of this unit.

<LENS>

Use commercially available blowers or lens tissue to remove any

dirt from the lens.

If dust is allowed to accumulate on the ventilation port filter, the

internal temperature of the unit will rise which may cause damage

to the unit. Clean the filter approximately once every 200 hours.

Remove the power cable from the power outlet, and remove dust

from the filter with a vacuum cleaner.

Be sure to vacuum the filter with the unit on its side, in order to

prevent dust from entering the filter itself.

■ Filter replacement

Replace the filter when it becomes difficult to remove dust from it.

1. Turn off the power and disconnect the power cable

from this unit.

2. Carefully place the unit upside down on a soft cloth

to prevent scratching.

3. Press the filter hook on the underside of the main

unit to remove the filter.

4. Attach the new filter firmly. The lamp will not light if

the filter is not attached correctly.

Important

• Contact a YAMAHA dealer or service center if you require

replacement filters.

107_DPX-1000(E)31-39 03.2.20, 2:08 PM35

E-36

Maintenance

■ Replacing the lamp cartridge

Important

• Be sure to use the replacement lamp cartridge PJL

327. Other lamp cartridges are not suitable for use

in this unit.

The lamp used as a light source in this unit is a consumable and

will gradually lose its brightness during the course of use. It is

advisable to replace the lamp when running time has exceeded

2000 hours.

You can view the current lamp running time in 3 <INITIAL> on

the menu. The LAMP warning indicator will blink when running

time exceeds 2000 hours. (See page 15.)

There will also be a message displayed on the screen. In this case,

follow the instructions below to replace the lamp cartridge. Be sure

to use the replacement lamp cartridge PJL 327. Other lamp

cartridges are not suitable for use in this unit. Consult the store

where this unit was bought for details on replacement lamp

cartridges.

Important

• Before starting to replace the lamp cartridge, turn off the

power, disconnect the power cable after the fan has com-

pletely stopped, and wait at least one hour for the lamp to

cool down.

• Do not remove any other screws than those specified in the

following steps.

1. Loosen the lamp cover screws.

2. Remove the lamp cover.

Important

• Take care not to drop the lamp or cover when replacing a

lamp in a ceiling mounted unit.

Lamp cover

screws

3. Loosen the screws of the lamp cartridge.

4. Grip the handle and pull the lamp cartridge to remove

it.

5. Insert the new lamp cartridge by reversing the above

steps, and tighten the screws to fix it into place.

6. Replace the lamp cover and secure it with the

screws.

The lamp will not turn on if the cover is not securely fastened.

Take care to attach it firmly in place.

7. Connect the unit to the power outlet, turn the unit on,

and reset “LAMP RUNNING TIME” on the 3 <INITIAL>

section in the menu. (See page 20.)

107_DPX-1000(E)31-39 03.2.19, 12:11 PM36

E-37

English

ADDITIONAL

INFORMATION

Troubleshooting

Problem

This unit does not turn on.

No picture

Image is unstable.

Picture is blurred.

The image becomes cloudy.

Cannot adjust focus or zoom, or the

vertical position of the lens.

Remote control does not work correctly.

COVER warning indicator lights up.

LAMP warning indicator lights up or

blinks.

TEMP warning indicator lights up.

FAN warning indicator lights up.

Remedy

Plug the power cable in firmly.

In order to protect the lamp, the unit will not turn on

again for 2 minutes after the power is turned off.

Correctly attach the filter cover.

Correctly attach the lamp cover.

Remove the lens cover.

Check the connections.

Select the correct input signal with the INPUT button.

Press the AUTO button.

Use the menu to adjust the signal setting to suit the

input setting.

Press the HIDE button again to cancel the HIDE

function.

Set the computer to display on the external monitor.

(Refer to the computer operating instructions.)

Correctly connect the cables to the appropriate

connectors.

Press the FOCUS button, and adjust the focus.

Adjust the projection angle and direction, and the

height of this unit.

Switch the unit power off until the condensation

disappears.

Set “LENS ADJUSTMENT LOCK” to OFF.

Replace both batteries with new ones.

Select an appropriate remote control sensor from the

menu.

Turn off this remote sensor.

Set the remote control code switch to the same ID

number as the setting on the “REMOTE CONTROL

ID” in the setting menu.

Tightly attach the filter cover.

Tightly attach the lamp cover.

Replace the lamp with a new one.

Check that the ventilation slots are not covered.

Contact the store where this unit was purchased.

Cause

The power cable is not plugged in.

You attempted to turn on this unit immediately after

turning it off.

The filter cover is not correctly attached.

The lamp cover is not correctly attached.

The lens cover has not been removed.

This unit is not correctly connected to the other

components.

The input signal has not been correctly selected.

The picture is turned off.

The computer is not set to display on the external

monitor.

The connection cables are not correctly attached to the

connectors.

The lens is not correctly focused.

The screen and the main unit are not facing each other

directly.

There is condensation on the unit.

“LENS ADJUSTMENT LOCK” in the menu is set to

ON.

The batteries are exhausted.

The remote control sensor is not set correctly.

There is a fluorescent lamp near the remote control

sensor being used.

The remote control code switch is incorrectly set.

The filter cover is not correctly attached.

The lamp cover is not correctly attached.

Lamp running time has exceeded 2000 hours.

The lamp has burned out.

The temperature inside this unit is extremely high.

The fan is broken.

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction

below does not help, set this unit in the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or

service center.

107_DPX-1000(E)31-39 03.2.20, 2:08 PM37

E-38

Specifications

■ Specifications

Optical

Projection mode .......................... DLP™ (Digital Light Processing)

Images of 1280 x 720 pixels, 0.8 inch

Lens ................................................... f=24.4 to 39 mm F=2.4 to 3.1

Electronic zoom (x 1.6)

Electronic focus

Lamp ..................................................................... 270 W SHP lamp

Image size ............................................................... 60 to 200 inches

Projection distance 1.8 to 6.05 m (70”7/8 to 236”1/5)

(Wide image, 16:9 screen)

Brightness ........................................ 800 ANSI lm (Standard mode)

500 ANSI lm (Cinema mode)

Contrast ...................................................... 1500:1 (Standard mode)

2700:1 (Cinema mode)

Electrical

Color mode .................................. NTSC, PAL, SECAM, NTSC4.43,

PAL-M, PAL-N, PAL60

Scanning frequency .......... H:15 to 54 kHz/V; 50 to 85 Hz (Analog)

50 to 60 Hz (Digital)

Input

VIDEO Composite signal

1Vp-p/75Ω, negative sync.

S VIDEO S video signal

Y: 1Vp-p/75Ω, negative sync.

C: 0.286 or 0.3Vp-p/75Ω

D4 VIDEO Component signal

Y with sync.: 1Vp-p/75Ω, negative sync.

(480i, 576i, 480p, 576p)

Y with sync.: 1Vp-p/75Ω, 3 values sync.

(1035i, 1080i, 720p)

B, PR: 0.7Vp-p/75Ω

INPUT A/INPUT B

Component signal

Y with sync.: 1Vp-p/75Ω, negative sync.

(480i, 576i, 480p, 576p)

Y with sync.: 1Vp-p/75Ω, 3 values sync.

(1035i, 1080i, 720p)

B, PR: 0.7Vp-p/75Ω

RGB signal

G with sync.: 1Vp-p/75Ω, negative sync.

(480i, 576i, 480p, 576p)

G with sync.: 1Vp-p/75Ω, 3 values sync.

(1035i, 1080i, 720p)

G: 0.7Vp-p/75Ω (when using HD/VD or SYNC)

B, R: 0.7Vp-p/75Ω

HD, VD: 1 to 5 Vp-p/2.2 kΩ, positive and negative

sync.

SYNC: 2Vp-p/2.2kΩ, negative sync. (480i, 576i)

SYNC: 1 to 5 Vp-p/2.2kΩ, positive and negative

sync. (480i, 576i, 480p, 576p)

DVI Digital RGB/Component signal

Controls

Remote ........................................................ RS-232C (D-Sub 9 pin)

Trigger ................ +12 V/Maximum 200 mA when the power is on;

0 V when the power is off (mini jack)

Remote control sensor

Wireless remote control ......................... one in front and one at rear

Wired remote control .................................................. one input jack

one output jack

General

Usable temperature range .............................................. 5°C to 35°C

Usable humidity range ................................................... 30% to 85%

(There should be no condensation.)

Power supply ................... AC 100 to 120 V/220 to 240 V, 50/60 Hz

Power consumption ................................................................ 365 W

Standby mode ..................................................................... 0.1 W

Noise Level ................................................... 30 db (Standard mode)

28 db (Economy mode)

Dimension ............................. 495 (W) x 189.5 (H) x 465.4 (D) mm

19”-1/2 (W) x 7”-1/2 (H) x 18”-5/16 (D) inch

Weight .............................................................. 13.8 kg (30 lbs 7 oz)

* Specifications are subject to change without notice.

This unit may interfere with reception if placed in close proximity

to a radio or television receiver. Follow the instructions in this

manual to install the unit correctly.

107_DPX-1000(E)31-39 03.2.19, 12:11 PM38

E-39

English

ADDITIONAL

INFORMATION

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUT

DIGITAL CINEMA PROJECTOR DPX-1000

ASPECT

DVI

INPUT B

RGB/YP

/YC

D4 VIDEO G/Y B/P

R/P

INPUT A

HD/SYNC VD

OUT IN

REMOTE

RS-232C

S-VIDEO VIDEO

TRIGGER OUT

465.4

18"-5/16

124.6

4"-7/8

119.1

4"-3/5

124

4"-7/8

297.4

11"-3/4

132.1

5"-3/16

495

19"-1/2

360

14"-3/16

189.5

7"-1/2

237.5

9"-3/8

3/8

(257.5

10"-1/8)

Specifications

■ Dimensional drawing

107_DPX-1000(E)31-39 03.2.19, 12:11 PM39

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Japan WA66190

000_DPX-1000(U)H14 03.2.19, 1:38 PM2

Yamaha DPX-1000 de handleiding

Merk: Yamaha

Model: DPX-1000

Categorie: Dataprojectoren

Type: de handleiding

Download PDF

rapport

in andere talen

English: Yamaha DPX-1000 Owner's manual
italiano: Yamaha DPX-1000 Manuale del proprietario
français: Yamaha DPX-1000 Le manuel du propriétaire
Deutsch: Yamaha DPX-1000 Bedienungsanleitung
dansk: Yamaha DPX-1000 Brugervejledning
svenska: Yamaha DPX-1000 Bruksanvisning
Türkçe: Yamaha DPX-1000 El kitabı
română: Yamaha DPX-1000 Manualul proprietarului

Andere documenten

CHAUVET DJ Vivid Drive 23N Referentie gids

Yamaha DPX-1000 de handleiding

Yamaha DPX-1000 de handleiding

in andere talen

Gerelateerde artikelen

Andere documenten