Yamaha DPX-1300 Handleiding

Merk: Yamaha

Model: DPX-1300

Categorie: Dataprojectoren

Type: Handleiding

Deze handleiding is ook geschikt voor

Projector DPX-1300

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Japan WF80490

DPX-1300

DIGITAL CINEMA PROJECTOR

PROJECTEUR CINEMA NUMERIQUE

DPX-1300

10_DPX-1300-Cover1-4_U.p65 9/22/05, 4:28 PM1

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the

obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped.

15 Be sure to allow spaces of at least 30cm above, behind and on

both sides the unit.

16 Do not place the following objects on this unit:

A vessel with water in it. If the vessel falls by vibrations and

water spills, it may cause damage to the unit, and/or you may

get an electric shock.

IMPORTANT!

Please record the serial number of this unit in the space below.

Model:

Serial No.:

The serial number is located on the bottom of the unit.

Retain this Owner’s Manual in a safe place for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

IMPORTANT SAFETY INSTRUCTIONS

10_DPX-1300-ULCaut_E.p65 9/20/05, 4:00 PM1

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void

your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used.

Follow all installation instructions. Failure to follow

instructions could void your FCC authorization to use this

product in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will not

result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the operation

of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is

found to be the source of interference, which can be determined

by turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures:

Relocate either this product or the device that is being affected

by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe

Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend

you to avoid prolonged exposure from excessive volume levels.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation

Address: 6660 Orangethorpe Avenue

Buena Park, CA90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: Projector

Model Name: DPX-1300

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See the user manual instructions if interference to radio reception is suspected.

10_DPX-1300-ULCaut_E.p65 9/20/05, 4:00 PM2

English

Caution: Read this before operating this unit.

•To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

Installation

• Install this unit in a well-ventilated, cool, dry, clean place with

at least 30 cm (1 feet) clearance on the top, right and left, and

at the back of this unit — away from direct sunlight, heat

sources, vibration, dust, moisture, and/or cold.

• Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds. To prevent fire or

electrical shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

• Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

• On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may cause electrical

shock to the user and/or damage to this unit.

• Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to restrict heat dissipation. If the temperature inside

this unit rises too much, it may cause fire, damage to this unit,

and/or personal injury.

•When installing this unit on the ceiling, make sure the ceiling

has sufficient strength to support this unit and the ceiling

mounts for an extended period of time. Installation must be

performed only by qualified service personnel.

• Install this unit near the AC outlet and where the AC power

plug can be reached easily.

Operation

• Remove the lens cover before starting any operation of this unit

to prevent the heat from staying around the lens. Operation

with the cap on may cause damage to this unit.

• Do not plug in this unit to a wall outlet until all connections are

complete.

• Only the voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than that

specified.

• Do not use force on switches, knobs and/or cords.

•Take care of this unit so that no foreign objects and/or liquid

drop inside this unit.

•To prevent damage by lightning, keep the power cord out and

outdoor antennas disconnected from a wall outlet or te unit

during the lightning storm.

• Do not look into the lens while this unit is turned on. It may

cause serious damage to your eyesight.

• Before moving this unit, press STANDBY/ON to set this unit

in the standby mode, and disconnect the AC power plug from

the wall outlet.

• Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reason.

• When not planning to use this unit for a long period of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

•When disconnecting the power cord from the wall outlet, grasp

the plug; do not pull the cable.

• Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

Others

• Clean the lens carefully so as not to create any scratches by

using a blower or lens paper.

•Replace the lamp when the LAMP warning indicator blinks in

red after the lamp usage has exceeded 2000 hours. Follow the

lamp replacement procedure described in this manual.

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an appropriate

3 pin plug fitted. For details, refer to the instructions described

below.

Note

•The plug severed from the mains lead must be destroyed, as a plug with

bared flexible cord is hazardous if engaged in a live socket outlet.

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be

connected to the terminal in the plug which is marked by the letter

E or by the safety earth symbol or coloured GREEN or GREEN-

and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

For Canadian customers

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-

003.

iii

10_DPX-1300-ULCaut_E.p65 9/20/05, 4:00 PM3

Table of contents

1 Getting started 2

Inappropriate places for installation ....... 2

Accessory check .................................... 2

2 Features 3

3 Controls and functions 4

4 Remote control 6

5 Preparation 10

6 Installation 12

Setting up the DPX-1300 ..................... 12

Projection distance ............................... 13

Projection image position ..................... 14

7 Connection 15

Connecting to AV components ............. 15

Connecting to computer devices ......... 16

8 Projection 17

Checking installation and connections...

Turning the projector power on ............ 18

Selecting an input signal ...................... 20

Adjusting the image ............................. 25

9 Menu 27

Menu configurations ............................ 27

Menu items .......................................... 28

Menu operations .................................. 38

Memory function

(Saving, Recall, Lock, Copy, Reset) 48

Reference 55

Glossary ............................................... 55

Compatible signal types ....................... 56

Maintenance ......................................... 58

Troubleshooting.................................... 60

Message display .................................. 62

LED Indicator meanings ....................... 63

Specifications ....................................... 64

Dimensional drawing ............................ 65

Getting started

Features

Controls and functions

Remote control

Preparation

Projection

Memory function

Reference

Connection

Installation

English

11_DPX-1300_E.p65 9/20/05, 4:00 PM1

◆Inappropriate places for installation

If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place

to install this unit by avoiding the places listed below.

1. Places where the temperature and humidity vary greatly

• Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely

low.

• This unit must be used within a temperature range of 5 to 35°C.

2. Places without adequate ventilation

• Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.

• Do not cover the ventilation slots of this unit. Covering the slots will obstruct heat dissipation.

• Install this unit on the firm surface.

• Do not cover this unit with a tablecloth, etc.

• Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.

• If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.

3. Places where it gets dusty

• If the filter is blocked with dust, the temperature of this unit may become too high.

4. Places with too much vibration or impact

•Vibration and impact can damage parts of this unit.

5. Places where this unit gets exposed to water or high humidity

• If this unit is exposed to water or high humidity, it may cause a fire or electrical shock.

6. Unstable places

• If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.

7. In close proximity to a Radio or Stereo

•The unit may interfere with reception if placed in close proximity to a radio or television receiver.

Warning

•To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.

◆Accessory check

Please check that all accessories listed here are included in your package.

• Remote control • Batteries (AA, UM-3 or R6) • Power cable

• Pin/BNC adapters • Lens cap

1 Getting started

• Trigger-out DC plug

(For USA only)

RESET

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

DVI

S VIDEO

INPUT

MEMORY

HDMI

INPUT

ASPECT

ESCAPE

11_DPX-1300_E.p65 9/20/05, 4:00 PM2

Features

English

Adjust 7 colors independently (including white), or use the

automatic color balance function

The DPX-1300 allows you to adjust the 7-axis WRGBYCM color coordinate and gain

parameters directly. For better consistency, you can also control color temperature and RGB

balance together, allowing you to check that the changes you make are always consistent with

your preferences.

The digital interface provides sharp, detailed images

The DPX-1300 is equipped with an HDMI terminal, which is set to become the standard for the

coming generation of products. Connect to a DVD player or set-top box with a HDMI terminal

to receive digital image data directly, and enjoy completely digitally processed images.

Compatible with the content protection function of HDCP.

Intelligent memory functions

The DPX-1300 can store six image memory settings, called memory numbers, for each input

jack. For each memory number, you can set parameters for different input resolutions, and the

unit will switch to the appropriate parameters when it begins displaying an image of an

appropriate resolution. For example, the unit automatically changes display settings without

changing memory numbers when you change from watching a DVD to watching a HDTV

image for which you have set different image menu item parameters.

In-line menus for image adjustment

You can access image adjustment menu items at the touch of a button, and adjust images while

viewing them without opening the menu screen.

Highly configurable electronic adjustment gives you the

freedom to place the projector wherever you want

A short focal length, high power zoom, and fully vertically adjustable lens allow you to use the

projector in a wide range of environments. You can also use the remote control to access many

lens functions such as focus, zoom, and lens shift to fine-tune the projector from your viewing

position.

Uses the DMD

device 720p DarkChip3

The projector uses the high contrast “720p DarkChip3

”, to reduce black levels even further

and reproduce contrasts close to that of a film.

2 Features

11_DPX-1300_E.p65 9/20/05, 4:00 PM3

◆Main unit <Front panel and controls>

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

DIGITAL CINEMA PROJECTOR DPX-1300

ASPECT

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

2 STANDBY/ON button

Switches the unit between Standby and On (operational)

modes.

3 ESCAPE button

Exits from submenus.

4 PATTERN button

Switches the built-in test pattern on and off.

5 ASPECT button

Turns the display aspect menu for the project image on and off.

6 (Enter) button

Sets values when the DPX-1300 is displaying the menu. When

the menu is not displayed, the DPX-1300 displays the in-line

image quality adjustment menu. (☞ page 47)

1 LED Indicators

The main unit is equipped with 5 indicators to display various states of operation. See page 63 for explanations of the LED indicator

meanings.

7 MENU button

Switches the settings and adjustments menu display on and off.

8 SETTING button

Selects lens adjustment modes.

9 INPUT button

Switches the input signal selection menu display on and off.

0 Cursor buttons

Use the h, g, +, - buttons for system operations, menu item

selection, and changing system values.

A STANDBY/ON indicator

(There is also an LED on the front panel of the main unit.)

B LAMP warning indicator

C COVER warning indicator

D TEMP warning indicator

E FAN warning indicator

Lamp cover

Ventilation inlet

Adjustable feet

Makes small adjustments to

the projection angle

Lens

Exhaust vent

Front remote control sensor

STANDBY/ON indicator

3 Controls and functions

Lens cap

11_DPX-1300_E.p65 9/20/05, 4:00 PM4

Controls and functions

English

HDMIDVI

G/Y B/P

R/P

INPUT A

HD/SYNC

OUT IN

REMOTE

TRIGGER OUT

S VIDEO VIDEO

INPUT B

RGB/YP

/YC

RS-232C

D4 VIDEO

765432190

ert

◆Main unit <Rear panel / Connections>

1 INPUT B (D-sub 15 pin)

Receives component video and RGB (RGB/YPBPR/YCBCR)

signals. Use a D-sub monitor cable to connect components to

this jack.

2 D4 VIDEO (D jack)

Receives signals output from the D jacks of other AV

components. It is compatible with D1 - D4 formats.

3 - 7 INPUT A (BNC jacks)

Receive component video and RGB signals. Connect

component signal connectors from AV components to input

jacks 3 - 5, and RGB signal connectors from computers to

input jacks 3 - 7. Use BNC cables for these connections.

3 G/Y (G, or luminance signal)

4 B/P

B/CB (B, or color difference signal)

5 R/PR/CR (R, or color difference signal)

6 HD/SYNC (Horizontal sync signal, composite sync signal)

7 VD (Vertical sync signal)

8 S VIDEO (Mini DIN jack)

Receives signals from S-VIDEO output jacks of other AV

components. Use an S-VIDEO cable for these connections.

9 AC inlet

Insert the supplied AC power cable here.

0 VIDEO (Pin Jack)

Receives composite video signals from the VIDEO output

jacks of other AV components. Use a video pin cable for these

connections.

q DVI (DVI jack)

Receives RGB signals from computers or AV components. Use

a DVI cable for this connection.

w HDMI

(HDMI

jack)

Receives HDMI

signals from computers or AV components.

e REMOTE IN / OUT jack

Connect the remote control to the REMOTE IN jack if you

want to use it through a cable. The REMOTE OUT jack

outputs the signal received through the REMOTE IN jack

without any change.

r RS-232C (D-sub 9 pin)

For use in servicing this unit.

t TRIGGER OUT

Outputs control signals to external components. This output

provides a potential of 12 V/ maximum 200 mA when this unit

is projecting. Use the supplied trigger-out DC plug (for US

model only) to control external components.

Rear remote control sensor

11_DPX-1300_E.p65 9/20/05, 4:00 PM5

◆ Remote control functions

Buttons on the remote control with identical names to those on the main unit perform identical functions. When using the remote control,

point it at the remote control sensor on the front or back of the main unit from a distance of 7m (23 feet) or less.

1 Transmit indicator

Lights up when the remote control sends infrared signals to the

main unit.

2 AUTO button

Automatically sets the DPX-1300 to the best settings for the

type of signal it is currently receiving.

3 V.POS button

Switches on or off the vertical adjustment mode for the entire

image.

4 ZOOM button

Switches on or off the size adjustment mode for the image the

DPX-1300 is projecting.

5 IRIS button

Switches on or off the lens iris change mode.

6 ESCAPE button

Exits from submenus.

7 Cursor buttons

Use the h ,g, +, - buttons to move the cursor within the on-

screen display.

8 ASPECT button

Turns the display aspect menu for the project image on and off.

9 RESET button

Resets all adjustable parameters to their default settings.

0 STILL button

Stops a moving image, displaying a still of the image the DPX-

1300 is projecting. Press STILL again to cancel this effect.

q INPUT area

Selects the INPUT jacks directly.

w MEMORY area

Calls stored memory (all parameter settings) directly.

e button

Switches the unit between Standby and On (operational)

modes.

r FOCUS button

Switches on or off the focus adjustment mode for the image the

DPX-1300 is projecting.

t PATT (PATTERN) button

Switches on and off the built-in test pattern.

y MENU button

Switches on and off the settings and adjustments menu display.

u (Enter) button

Sets values when the DPX-1300 is displaying the menu. When

the menu is not displayed, the DPX-1300 displays the in-line

image quality adjustment menu. (☞ page 47)

4 Remote control

RESET

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

DVI

S VIDEO

INPUT

MEMORY

HDMI

INPUT

ASPECT

ESCAPE

11_DPX-1300_E.p65 9/20/05, 4:00 PM6

Remote control

English

i INPUT button

Switches on and off the input signal selection menu display.

o LIGHT switch

Moving this switch lights the high-use AUTO (2), ESCAPE

(6), ASPECT(8) ,

(e), MENU (y), and INPUT (i)

buttons. The light disappears if you do not perform any

operation within 10 seconds.

p HIDE button

Temporarily halts projection of the image the DPX-1300 is

currently displaying. Press again to cancel this effect.

a Remote control code switch

Selects ID-1 or ID-2 when operating two main units with one

remote control. You can set the ID for the main unit in the

menu (The default setting is ID-1).

s Remote control cable jack

Connect this jack and REMOTE IN jack on the main unit using

a cable (commercially available) to use the remote control with

a wired connection. (☞ page 8)

INPUT

RIS

.POS

PATT

D-2

RESET

S VIDEO

VIDEO

DVI

HDMI

MEMORY

LIGHT

INPUT

SCAPE

ASPECT

11_DPX-1300_E.p65 9/20/05, 4:00 PM7

◆Loading the batteries into the remote control

1. Remove the battery compartment cover.

2. Insert two batteries (AA, UM3, or R6 type), matching the polarity

markings on the batteries with those in the battery

compartment.

3. After loading the batteries, close the cover until it snaps into

place.

Warning

• If the remote control must be used closer to the main unit than normal, or does not always operate correctly, exchange the

batteries for new ones.

• Do not mix old and new, or different types of batteries.

• Remove the batteries if you do not plan to use the unit for a long time.

• If the batteries leak, dispose of them immediately, taking care not to touch the battery fluid. If the battery fluid comes into contact

with your eyes, mouth, or skin, rinse it off with water immediately and consult a doctor. Clean the battery compartment thoroughly

before installing new batteries.

◆Using the remote control with a wired connection

Use a 2P monaural miniplug cable (commercially available) to connect the remote control jack on the underside of the remote control to the

REMOTE IN jack on the main unit. Use the wired remote control configuration to control the DPX-1300 without having to be within range

of the remote sensor.

PAT

FOCUS

ZOOM

-1

ESET

IDE

STIL

LIGH

CAPE

ECT

INPU

INPUT

IDE

VID

HDMIDVI

G/Y B/P

R/P

INPUT A

HD/SYNC VD

OUT IN

REMOTE

TRIGGER OUT

S-VIDEO VIDEO

INPUT B

RGB/YP

/YC

RS-232C

D4 VIDEO

11_DPX-1300_E.p65 9/20/05, 4:00 PM8

Remote control

English

Distance to sensor Angle to sensor

7 m 30˚ vertically and horizontally

(approximate value) (approximate value)

◆ Limits for using the remote control

Use the remote control within the following parameters. The remote control may not function correctly if you use it outside the limits

described here.

Warning

• Bright or fluorescent light on the main unit remote sensor may inhibit the functioning of the remote control.

• Objects placed between the main unit remote sensor and the remote control may block the remote control signal and inhibit

functioning.

Use within a left/right arc of 30 degrees Use within a vertical arc of 30 degrees

HDMI

G/Y B/P

R/P

INPUT A

HD/SYNC

OUT IN

REMOTE

TRIGGER OUT

S-VIDEO VIDEO

INPUT B

RGB/YP

/YC

RS-232C

D4 VIDEO

RESET

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

BDVI

S VIDEO

INPUT

MEMORY

HDMI

INPUT

ASPECT

ESCAPE

RESET

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

B DVI

S VIDEO

INPUT

MEMORY

HDMI

INPUT

ASPECT

ESCAPE

11_DPX-1300_E.p65 9/20/05, 4:00 PM9

Before projection, install the main unit and a screen, connect the main unit to an AV component or computer, and adjust the projection image.

You can begin projection as soon as installation is complete.

Refer to the sections below for information on how to install the main unit to suit your viewing environment.

◆If you have not installed the main unit or screen

• Immediately after purchase, when you have not installed either the main unit or a screen.

• When moving the main unit and screen to a new location.

◆If you have installed the main unit and screen, and connected a

source component

• You have installed the main unit and screen, and connected source components.

• You are using the main unit in a previously installed location with previously connected source components.

◆If you have installed the main unit and screen, but not connected

any image playback components

• You have installed the main unit and screen, but not connected any source components.

• You are using the main unit in a previously installed location, and wish to change the component you use as a signal source.

You do not need to carry out step 3 or step 4 if you

do not want to adjust the projection image. If the

unit does not project the image correctly, it may not

be connected correctly. In this case, carry out this

procedure starting from step 2.

STEP3

Select an image and

project.

☞ page 17 - 26

• The image is used

for adjusting the

image position

and focus.

STEP4

Adjust the

projection image.

☞ page 27 - 47

• Use the menu to

adjust projection

details.

Projection

preparations

complete

STEP2

Connect AV

components or a

computer to the

main unit.

☞ page 15 - 16

STEP3

Select an image and

project.

☞ page 17 - 26

• The image is used

for adjusting the

image position

and focus.

STEP4

Adjust the

projection image.

☞ page 27 - 47

• Use the menu to

adjust projection

details.

Projection

preparations

complete

STEP 1

Install the main unit

and screen.

☞ page 12

STEP3

Select an image and

project.

☞ page 17 - 26

• The image is used

for adjusting the

image position

and focus.

STEP2

Connect AV

components or a

computer to the

main unit.

☞ page 15 - 16

Projection

preparations

complete

Preparation

STEP4

Adjust the

projection image.

☞ page 27 - 47

• Use the menu to

adjust projection

details.

11_DPX-1300_E.p65 9/20/05, 4:00 PM10

Prepararion

English

Step2

Connect an AV component or computer

• Connect AV components

• Connect a computer ☞ page 15 - 16

Step3

Turn the power on and selecting an

image for projection

•Turn on the projector power

•Begin playback of the input image

• Select an input signal

• Select a projection image aspect

• Adjust the image

Focus/Vertical and Horizontal position/Size/Iris

☞ page 17 - 26

Step1

Set up the projector and screen

• Install the projector

• Install the screen ☞ page 12 - 14

Only adjust these

parameters when

necessary. It is not

necessary to adjust these

settings once you have set

them initially.

Step4

Use the menu to adjust the image quality and

other parameters

• Image quality: Set image quality details

• Signal setting: Set input signal details

• Default settings: Set the default settings for everyday use

• Installation settings: Set to suit your viewing environment ☞ page 27 - 47

11_DPX-1300_E.p65 9/20/05, 4:00 PM11

Setting up the DPX-1300

◆ Mounting the projector on a table

A: From in front of a screen

Place the unit on a table to project and view the image from in front of the screen. Usually,

place the unit on a reasonably high table. The height from the bottom of the unit to the center

of the lens is 12.4 cm (4”-7/8).

B: From behind a screen (using a semi-translucent screen)

Place the unit on a table to project and view the image from behind a semi-translucent

screen. The distance between the projector and the screen should be the same as “A: From in

front of the screen”.

• Set the [Location] menu item in the [Setup] menu group to [Rear/Table]. (☞ page 27 - 47)

◆ Mounting the projector on the ceiling

There are two kinds of brackets (sold separately: PMT-L31 and PMT-H35), which you can use to mount the projector on the ceiling. Please

consult your dealer for details on their use, and have installation done by either your dealer or a reputable contractor.

C: From in front of a screen

Mount the unit on the ceiling to project and view the image from in front of the screen. The

distance between the projector and the screen should be the same as “A: From in front of the

screen”.

•

Set the [Location] menu item in the [Setup] menu group to [Front/Ceiling]. (☞ page

27 - 47

)

D: From behind a semi-translucent screen

Mount the unit on the ceiling to project and view the image from behind a semi-translucent

screen. The distance between the projector and the screen should be the same as “B: From

behind a screen”.

•

Set the [Location] menu item in the [Setup] menu group to [Rear/Ceiling]. (☞ page

27 - 47

)

There are four ways of mounting the projector.

Installation

Mounting method

Placed on a table

Mounted on the

ceiling

Projection method

A: From in front of a screen

C: From in front of a screen

B: From behind a semi-translucent screen

D: From behind a semi-translucent screen

11_DPX-1300_E.p65 9/20/05, 4:00 PM12

Installation

English

The most suitable distance between the screen and the projector (see Projection distance [a]) depends on the size of the screen (diagonal

length) you use. You can use the zoom function to adjust the projection distance within a preset range from Wide to Tele. You can also alter

the V.POS parameter to adjust the vertical position of the image to better suit the screen. Use the information in the table below to determine

the best location to place the projector in to suit your screen size.

Projection distance

Since the DPX-1300 has a 16:9 panel, the ideal installation location for use with a 4:3 screen depends on the size of the image you wish to

view.

60'' 80'' 100'' 150'' 200''

*These are theoretical values.

During actual use there may be a deviance of a few percent.

(*1) Projects a 16:9 image that completely fills the screen (leaves a black line at the top and bottom of the screen).

(*2) Projects a 4:3 image that completely fills the screen.

(*3) When projecting both 16:9 and 4:3 images.

You can use the zoom function to make efficient use of the screen for both *1 and *2 above. The projection distance in this case is

between Wide in *2 and Tele in *1. Use the zoom to adjust the size of the projection images so that they fill the screen completely. Note

that adjustments to V.POS may cause the position of the image to change.

Projection distance [a]

Lens

centerline

Screen size

100

110

120

150

200

Screen size

(inch)

1.78 – 2.88

2.08 – 3.37

2.39 – 3.86

2.70 – 4.35

3.00 – 4.84

3.31 – 5.33

3.62 – 5.82

4.54 – 7.29

6.07 – 9.74

Projection distance [a]

Wide (m) – Tele (m)

Screen size

(inch)

16:9 image (*1)

Wide (m) – Tele (m)

4:3 image (*2)

Wide (m) – Tele (m)

Projection distance[a]

100

120

200

1.63 – 2.64

2.19 – 3.54

2.76 – 4.44

3.32 – 5.34

5.58 – 8.94

2.17 – 3.52

2.93 – 4.72

3.68 – 5.92

4.43 – 7.12

7.43 – 11.92

(*3)

11_DPX-1300_E.p65 9/20/05, 4:00 PM13

Follow the instructions to adjust the position of the projected image on screen.

This illustration shows the limits within which the

zoom function can alter projection distance [a] in

relation to screen size. You can adjust the image

within these limits so that it fills the screen

completely. ( ☞ page 26)

You can adjust the vertical position of the

projection image up or down by half of the height

of the screen. For example, shifting V.POS fully up

brings the lower limit of the image above the

centerline of the lens. (☞ page 25)

If you mount this unit on a tabletop, you can use the adjusters on its underside to change the

position of the projection image. Rotate the movable part of the two screw-type adjusters at

the front bottom of the case to adjust the height. The movement range of the adjusters is 3

cm (1-1/4 inch). Adjust with care as loosening them further than 3 cm may cause them to

separate from the unit.

Projection image position

◆ Keystone adjustment

If you mount the unit at an angle to the screen, it projects trapezoidally distorted images. You can use the [V keystone Correction] or [H

keystone Correction] item in the [Setup] menu group to rectify this. (☞ page 36)

Memo

• If the keystone is adjusted aspect ratio may not be correctly maintained. To correctly maintain the aspect ratio, try to use the DPX-

1300 with the lens shift in the center position.

• The video may be disturbed by keystone correction. Wherever possible, we recommend setting up so the screen and projector

form a right angle.

Wide Tele

Lens centerline

(When shifted

fully up)

Lens centerline

(When shifted

fully down)

11_DPX-1300_E.p65 9/20/05, 4:00 PM14

Connection

English

Connecting to AV components

This unit is equipped with 7 types of video input jacks for AV components. Follow the diagram to connect AV components to this unit, taking

care to use cables and adapters that match the input jacks.

Warning

• Be sure to turn off the power of this unit and the source component before attempting connection.

• Connection methods and jack names may differ depending on the component you are attempting to connect. Refer to the owner’s

manual for the component.

• Insert all plugs firmly to avoid noise or other problems.

Memo

• Be sure to connect Y/PB/PR and Y/CB/CR to the jacks with the correct signals when connecting AV components to INPUT A. Refer to

the owner’s manual of the source component for more information. You may need to make connections to HD/SYNC and VD for

RGB video signals.

D connector

cable

D-sub

monitor

cable

BNC cable for

component connection

Pin/BNC

adapters

Pin cable

Video pin cable

S-Video cable

D1—4

output

connectors

Pin jacksD-sub

Component/RGB video output connectors

Image output from AV components

BNC jacks S-Video output

jack

Video output

jack

HDMI cable (digital)

HDMI

output

connector

7 Connection

DVI cable (digital)

DVI output

connector

Input

VIDEO

S VIDEO

INPUT A

INPUT B

D4 VIDEO

HDMI

DVI

Signal type

Composite video

S-Video

Component video/RGB video

Component video

Component video/RGB video (digital)

RGB video (digital)

Connector type

Pin jack

Mini DIN connector

BNC connector x 3-5

D-sub 15 pin

D connector

HDMI connector

DVI connector

HDMI

G/Y B/P

R/P

INPUT A

HD/SYNC

OUT IN

REMOTE

TRIGGER OUT

S VIDEO VIDEO

INPUT B

RGB/YP

/YC

RS-232C

D4 VIDEO

DVI

11_DPX-1300_E.p65 9/20/05, 4:00 PM15

You can use the following three methods to connect to computer devices. Be sure to use cables with jacks that match the connectors and

jacks you wish to use. The HDMI terminal does not support PC signals.

Connecting to computer devices

HDMIDVI

G/Y B/P

R/P

INPUT A

HD/SYNC

OUT IN

REMOTE

TRIGGER OUT

S VIDEO VIDEO

INPUT B

RGB/YP

/YC

RS-232C

D4 VIDEO

D-Sub monitor

cable

BNC monitor cable

Monitor output terminal

Computer devices

Use the supplied trigger-out DC plug to control external

components.

Be sure to solder the wires from an external component to the

plug terminals with the correct polarities, as illustrated at left.

Warning

• Soldering the wires to terminals with incorrect polarity may

cause bodily injury or may damage this unit and the

external component connected to this unit with this cable.

Information for installers

(for US model only)

+ polarity (inside)

- polarity (outside)

(GND)

+ polarity

- polarity

Input

INPUT A

INPUT B

DVI

Signal type

RGB (Analog)

RGB (Digital)

Connector type

BNC jack x 5

D-sub 15 pin

DVI connector

DVI cable

11_DPX-1300_E.p65 9/20/05, 4:00 PM16

Projection

English

Checking installation and connections

◆ Pre-operation check

Prior to projection, adjust settings to suit the location of the main unit and screen, and the input signal you are using.

However, there is usually no need to adjust any settings if you have not changed the installation location or components since the last time

you used this unit. Check settings and connections only when the unit does not appear to project images correctly.

PHONO

DVR

STANDBY

/ON

PURE DIRECT

2CH/MULTI CH

SPEAKERS

VIDEO AUX

REC OUT/ZONE 2

INPUT MODE

SOURCE/REMOTE

DVDDTV/LD

MD/TAPE

CD-R

TUNER

VIDEO AUX

VCR 2

VCR 1

SAT

CABLE

A B

STRAIGHT

EFFECT

MULTI CH

INPUT

DSP

PROGRAM

BALANCE

TONE

CONTROL

VOLUME

INPUT SELECTOR

MULTI JOG

SILENT OPTIMIZER

MIC

PHONES

OPTICAL

AUDIO

VIDEO

S VIDEO

Is the main unit power

turned on?

Main unit

Are the components connected correctly?

“Connecting to AV components”

☞ page 15 - 16

Image source component

Is the source component power

turned on?

For an explanation of detailed settings, see “Menu”. ☞ page 27 - 47

Check installation and connections

Select an image for projection and image adjustment

Projection preparations complete

Turn on the projector power.

Begin playback of the source image for adjustment.

Select a projection image.

(Select an input signal and projection image aspect.)

Adjust focus and vertical/ horizontal positioning.

8 Projection

Prior to projection, check that the main unit and screen are correctly installed, and that source components are connected correctly.

To project images, carry out the following procedure.

Is the screen installed correctly?

“Setting up the DPX-1300”

☞ page 12

12_DPX-1300_E.p65 9/20/05, 4:00 PM17

◆ Turning the power on

Always remove the lens cap before operating the main unit.

1. Insert the supplied power cable

firmly into the AC inlet at the rear

of the main unit, then insert the

plug into an AC outlet.

The STANDBY/ON indicator lights red.

2. Press the STANDBY/ON button

(the

button on the remote

control).

The indicator blinks green and the lamp

lights up in preparation for projection. After

approximately 35 seconds, the indicator

changes from blinking to steady green,

indicating that the unit is ready to project.

Warning

• Do not remove the power cable while the STANDBY/ON indicator is blinking green or

lit steady green. This could damage the lamp or reduce lamp life.

HDMIDVI

G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC

OUT IN

REMOTE

TRIGGER OUT

S-VIDEO VIDEO

INPUT B

RGB/YP

BPR/YCBCR

RS-232C

D4 VIDEO

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

STANDBY/ON

indicator

AC inlet

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

Remote Control Main unit

button STANDBY/ON button

Turning the projector power on

12_DPX-1300_E.p65 9/20/05, 4:00 PM18

Projection

English

1. Press the STANDBY/ON button.

A confirmation message appears on the

screen.

◆ Placing the DPX-1300 in standby mode

2. If you wish to place the DPX-1300

in standby mode, press the

STANDBY/ON button again.

The lamp changes to a half lit state, and the

fan activates for 2 minutes to cool the lamp.

During this time, the STANDBY/ON

indicator blinks red, and pressing

STANDBY/ON does not turn main unit

power on again. When the unit finishes

cooling, the fan stops, and the STANDBY/

ON indicator turns red.

Memo

• The lamp may blink when half lit. This is not a defect.

Warning

• Do not remove the power cable while the STANDBY/ON indicator is blinking green

or when the fan is activated. This could damage the lamp or reduce lamp life.

• This unit is not disconnected from the AC power source as long as it is connected

to the AC outlet, even if this unit itself is turned off by STANDBY/ON.This state is

called the standby mode. In this state, this unit is designed to consume a very small

quantity of power.

• If you do not plan to use the main unit for a long period of time, attach the lens cap

and remove the plug from the AC outlet.

• Condensation may appear on the unit if the temperature of the surrounding

environment changes quickly. Condensation may also cause the projected image to

be cloudy. Place the unit in standby mode until the condensation disappears.

Switching the unit on when condensation is present may damage the unit.

Turning the projector power on

AC inlet

Press again to enter standby.

HDMI

G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC

OUT IN

REMOTE

TRIGGER OUT

S-VIDEO VIDEO

INPUT B

RGB/YP

BPR/YCBCR

RS-232C

D4 VIDEO

DVI

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

Remote Control Main unit

button STANDBY/ON button

12_DPX-1300_E.p65 9/20/05, 4:00 PM19

◆ Selecting using the INPUT button

Press the INPUT button to select an input signal from a source component. Choose from the following:

Projection image signal

Selects component video signals received from AV components connected to the VIDEO jack.

Selects S-Video signals received from AV components connected to the S VIDEO jack.

• Component : Selects component signals received from the INPUT A BNC jacks.

• RGB PC : Selects RGB signals received from computers connected to the INPUT A BNC jacks.

• RGB TV : Selects RGB signals received from AV components connected to the INPUT A BNC jacks.

• Component : Selects component signals received from the INPUT B D-sub 15 pin jack.

• RGB PC : Selects RGB signals received from computers connected to the INPUT B D-sub 15 pin jack.

• RGB TV : Selects RGB signals received from AV components connected to the INPUT B D-sub 15 pin jack.

• Auto : Signals input to the HDMI jack from AV components (automatically distinguishes between

component and RGB signals).

• Component : Selects digital component signals received from AV components connected to the HDMI jack.

• RGB TV : Selects digital RGB signals received from AV components connected to the HDMI jack.

• RGB PC : Selects RGB signals received from computers connected to the DVI jack.

• RGB TV : Selects RGB signals received from AV components connected to the DVI jack.

INPUT SIGNAL

VIDEO

S VIDEO

INPUT A

INPUT B

HDMI

DVI

D4 VIDEO Selects component signals received from AV components connected to the D4 VIDEO jack.

Selecting an input signal

12_DPX-1300_E.p65 9/20/05, 4:00 PM20

Projection

English

Selecting an input signal

1. Press the INPUT button.

The input signal selection menu appears on

the display.

4. Select an appropriate setting

from [Component], [RGB PC], or

[RGB TV] and press the

button

to confirm the setting.

3. Press the + button to open the

submenu.

2. Use the h or g buttons to select

an input signal, then press the

button.

The

mark to the right of the input signal

name indicates that there is a submenu

available for selection.

Input signal

VIDEO

S VIDEO

INPUT A

INPUT B

HDMI

DVI

Input signal

VIDEO

S VIDEO

INPUT A

INPUT B

HDMI

DVI

Input signal

VIDEO

S VIDEO

INPUT A

INPUT B

HDMI

DVI

Component

RGB PC

RGB TV

Input signal

VIDEO

S VIDEO

INPUT A

INPUT B

HDMI

DVI

Warning

•You can select [Component], [RGB PC], or [RGB TV] for INPUT A and INPUT B, or

[Auto], [Component], or [RGB TV] for HDMI, from the submenu. If you do not select a

setting, the unit continues to use the setting from the last signal it received. To

change this setting, carry out the following procedure.

Memo

• If you set your laptop or notebook computer to display on its built-in display and on

an external monitor simultaneously, the main unit may not project the image

correctly. In this case, set your computer to display on the external monitor only.

Refer to your computer’s operating instructions for further details.

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUT

ASPECT

RESET

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

B DVI

S VIDEO

INPUT

MEMORY

HDMI

INPUT

ASPECT

ESCAPE

+ button

Remote cotrol Main unit

button

INPUT button

Cursor button

12_DPX-1300_E.p65 9/20/05, 4:00 PM21

Selecting an input signal

1. Press the ASPECT button.

The display aspect selection menu appears

on the display.

◆ Selecting a display aspect for a projection image

The display aspect parameter sets the ratio of height to width the unit uses to project an image for an input signal.

Memo

• The display aspect you can use depends on the current input signal. When the input

signal contains display aspect information, set the display aspect parameter to

[Auto] to detect the appropriate display aspect setting automatically.

•You can also use the [Display Aspect Ratio] page in the menu screen to select a

display aspect. (☞ page 27- 47)

2. Use the h or g button

to select a suitable display aspect

setting, then press the button.

If you select [Special] or [Through],

pressing the + button displays the submenu.

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUT

ASPECT

RESET

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

B DVI

S VIDEO

INPUT

MEMORY

HDMI

INPUT

ASPECT

ESCAPE

cursor button

Remote cotrol Main unit

button

ASPECT

button

Display Aspect Ratio

Auto

Normal

Squeeze

Smart Zoom

Zoom

Special

Through

Display Aspect Ratio

Auto

Normal

Squeeze

Smart Zoom

Zoom

Special

Through

12_DPX-1300_E.p65 9/20/05, 4:00 PM22

Projection

English

Memo

• Refer to the glossary for explanations of terms such “letterbox” or “squeeze”. (☞ page 55)

Auto

Detects information encoded in letterbox or squeeze type input

signals and automatically selects an appropriate display aspect.

Depending on the input source, the unit may not change to the

most appropriate mode. In this case, manually select a suitable

setting.

Normal

Projects images with their original display aspect. Depending

on the input signal, black areas may appear to the left and right

of the image.

Squeeze

Returns horizontally compressed images to their original

aspect. Use this mode to display horizontally squeezed images

in a normal wide aspect manner.

Smart Zoom

Stretches the left and right edges of a 4:3 image without

altering the image center, to project a 16:9 image that fills the

screen.

Zoom

Projects images the unit receives in letterbox format as 16:9

images that fill the screen.

Special

Subtitle Zoom

The best format for projecting subtitled letterbox format

software. See page 45 for the operational procedure.

• Subtitle area: Adjust the area used to display subtitles on

screen.

•V Scroll: Adjusts the vertical position of the subtitles.

Cinema Zoom

Removes the black bar from Cinescope size screens (2.35:1) to

display a full horizontal image, cutting both screen sides.

There are two types: SDTV for 4:3 images, and HDTV for

16:9 images.

Cinema Squeeze

Removes the black bar from cinescope size screens for 4:3

images and resize the vertical image so that a 16:9 panel

resolution is fully displayed, cutting both screen sides.

14:9 Zoom

Displays 14:9 images with a full vertical aspect, retaining the

black area at either side of the screen.

Through

Normal Through

Projects images without stretching or reducing them. The size

of the projection image depends on the resolution of the image

received.

Squeeze Through

Widens the image received to project it with a 16:9 aspect

ratio. The size of the projection image depends on the

resolution of the image received. This mode is not available for

RGB PC input signals.

Selecting an input signal

12_DPX-1300_E.p65 9/20/05, 4:00 PM23

Selecting an input signal

Input signal type

Standard 4:3 image

Letter box

Squeeze

14:9 image

HDMI

RGB PC

All

Display aspectInput image Projected image

SUBTITLE

Normal

Cinema

Scope

Normal

Squeeze

Normal

Smart Zoom

Zoom

Subtitle Zoom

Cinema Zoom

Squeeze

Cinema Squeeze

14:9 Zoom

Normal

Cinema Zoom

Normal

Normal Through

Squeeze Through

12_DPX-1300_E.p65 9/20/05, 4:00 PM24

Projection

English

Carry out the following adjustments to obtain optimal projection conditions.

◆ Adjusting the vertical position – V.POS button

If the center of the screen is not in line with the center of the lens of the DPX-1300, use the V.POS button to adjust the position of the image

up or down. You can adjust the image to a maximum of half of the height of the projection screen.

1. Press the V.POS button on the

remote control, or press the

SETTING button on the main unit

repeatedly to select [Lens Shift]

from the display menu.

2. Press the h or g button to move

the projected image to a suitable

place.

3. To exit from the adjustment

mode, press the V.POS or

ESCAPE button.

◆

Using test patterns to adjust the projection image – PATT button

The DPX-1300 is equipped with three test patterns, the crosshatch pattern necessary for focus and keystone adjustment, and the grayscale

and color bar patterns necessary for adjusting image quality.

1. Press the PATT button on the

remote control, or the PATTERN

button on the main unit.

2. Press the + or - button to select

the necessary pattern.

3. To exit from the test display,

press the PATT or PATTERN

button.

AUTO

SETTING

ESCAPE

PATTIRIS

ZOOM FOCUSV. POS

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

AUTO

SETTING

ESCAPE

PATTIRIS

ZOOM FOCUSV. POS

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

Crosshatch pattern

Grayscale pattern

Color bar pattern

Adjusting the image

V.POS

button

ESCAPE button

Lens Shift

PATTERN button

SETTING

button

PATT

button

12_DPX-1300_E.p65 9/20/05, 4:00 PM25

Adjusting the image

◆ Adjusting the size of an image – ZOOM button

Enlarge or reduce the size of the projection image to match the size of the screen. The zoom ratio is 1:1.6.

1. Press the ZOOM button on the

remote control, or press the

SETTING button on the main unit

repeatedly to select [Zoom] from

the display menu.

2. Press the h or g button to adjust

the image to a suitable size.

3. To exit from the adjustment

mode, press the ZOOM or

ESCAPE buttons.

◆ Adjusting the image focus – FOCUS button

Adjust the focus of the on-screen image.

1. Press the FOCUS button on the

remote control, or press the

SETTING button on the main unit

repeatedly to select [FOCUS]

from the display menu.

Memo

• When you want to use the test pattern

to adjust image focus press the PATT

button on the remote control, or the

PATTERN button on the main unit

before carrying out step 1.

2. Press the h or g button to adjust

the focus of the projected image.

3. To exit from the adjustment

mode, press the FOCUS or

ESCAPE buttons.

◆ Adjusting the iris setting – IRIS button

Press the g button to reduce the aperture of the iris for increased black levels and contrast, or the h button to increase aperture to obtain a

brighter image.

1. Press the IRIS button on the

remote control, or press the

SETTING button on the main unit

repeatedly to select [IRIS] from

the display menu.

2. Press the h or g button to adjust

the iris setting for the projected

image.

3. To exit from the adjustment

mode, press the IRIS or ESCAPE

button.

AUTO

SETTING

ESCAPE

PATTIRIS

ZOOM FOCUSV. POS

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

AUTO

SETTING

ESCAPE

PATTIRIS

ZOOM FOCUSV. POS

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

AUTO

SETTING

ESCAPE

PATTIRIS

ZOOM FOCUSV. POS

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

ESCAPE button

SETTING

button

ZOOM

button

Zoom

Focus

Iris

ESCAPE button

FOCUS

button

ESCAPE button

IRIS

button

SETTING

button

SETTING

button

12_DPX-1300_E.p65 9/20/05, 4:00 PM26

English

VIDEO+ : Enter

Image

Memory 1

Signal Initial Setup

Move Menu Window

Color Adjustment Standard 6700K

0.000uv

Black Level

a b c d e

White Level 0

Gamma

Hue 0

Saturation 100

Level Adjustment

Iris

White Peaking

Sharpness Gain

Sharpness Type

Menu configurations

Configure the DPX-1300 to suit your viewing environment by adjusting image quality, initial settings, defaults, and setup characteristics.

These parameters can be accessed through the menu.

Press the MENU button on the remote control or the main unit to display the menu screen. The menu consists of the [Image], [Signal],

[Initial], and [Setup] menu groups, each containing numerous items you can use for configuring the unit. Note that some items are only

selectable for certain types of input signal (Video, Component, RGB TV, RGB PC).

Menu groups appear in the upper area of the display, as the top level of menu composition. Menu items appear in the left area of the display.

You can select settings and make adjustments to suit your preferences. See page 38 - 47 for an explanation of how to use the menu.

◆ Menu screen

Some menu items contain an additional level of items called a submenu. Moving the cursor to an item with a submenu attached displays “ ”

to the right of the item name. Some submenus contain further levels of submenus containing items for selection.

In this example, the menu contains three submenus, and one of the submenus contains a further submenu.

Menu items

Items displayed here depend on

the menu group you select.

The picture on the right shows

menu items in the [Image] group

for example.

Color Adjustment Standard

WRGB

WRGBYCM

6700K

0.000uv

6500K

0.000uv

6500K

0.000uv

Color Temp.

VIDEO

6900K

0.005uv

–

Image

Memory 1

Signal Initial Setup

Move Menu Window

: Edit

0.5

0.0

0.0 0.5 x

0.35

0.25

0.3

0.4

0.25 0.350.3

0.02uv

0.00uv

0.02uv

10000

9000

8000

7000

6000

5000

–

Indicates the existence of a submenu

[Color Adjustment] submenu

[WRGB] submenu

Menu group

[Image] selected.

<Example: When in Image menu>

9 Menu

a b c d e

Memory 1 VIDEO

Image

Black Level

White Level

Gamma

Hue

Saturation

Sharpness Gain

Sharpness Type

Color Adjustment

Level Adjustment

Iris

Signal Initial Setup

White Peaking

Move Menu Window

WRGB 6500K

0.000uv

[Move Menu Window] area

Use this selection area to move

menu screens. See page 44 for

more information.

Input jack display area

Shows the currently selected

input jack.

Parameter adjustment area

Memory number status

Displays the currently selected memory number and memory status. Change

the memory number and lock/unlock memory settings here(☞ page 48-50).

Menu operation guide

Displays helpful instructions when

special operations are necessary.

13_DPX-1300_E.p65 9/20/05, 4:01 PM27

◆ Menu item list:

● Image

Black Level (Brightness)

While Level (Contrast)

Gamma

Hue

Saturation

Sharpness Gain

Sharpness Type

Color Adjustment 1

White Peaking

Iris

Level Adjustment 2

● Signal

Display Aspect Ratio 3

Overscan

3D Y/C separation

Progressive Mode

Color Space Conversion

Setup Level

Overshoot Supp. Range

Overshoot Supp. Level

Noise Reduction Type

Noise Reduction Level

Horiz. Display Position

Ve rt. Display Position

Signal Level

Signal Status 4

● Initial

Color System 5

INPUT A Signal 6

INPUT A Sync Type 7

INPUT B Signal 6

INPUT B Sync Type 7

HDMI Signal

DVI Signal

Auto Power Off

Auto Input Search

Display Language 9

Lamp Running Time 10

Reset 11

● Setup

Location 12

V Keystone Correction

H Keystone Correction

Remote Control Sensor 13

Remote Control ID 14

Lens Adjustment Lock

Lamp Power

Menu Color 15

Message

Trigger Out 16

Baud Rate

Memo

• Menu items you can choose may differ depending on the input signal type.

• Items in the menu that contain submenus are marked with “ ”.

Menu items

13_DPX-1300_E.p65 9/20/05, 4:01 PM28

English

The submenus display different items depending on the input signal. Items in submenus that contain further submenus are marked with “ ” .

● Signal

3: Display Aspect Ratio

Auto

Normal

Squeeze

Smart Zoom

Zoom

Special

Through 5

4: Signal Status

Resolution

Sync Type

Sync Polarity

Frequency

Source Equipment (HDMI only)

● Setup

12: Location

Front/Table

Front/Ceiling

Rear/Table

Rear/Ceiling

13: Remote Control Sensor

Front & Rear

Front

Rear

Off

14: Remote Control ID

ID 1

ID 2

15: Menu Color

Monotone 6

Color 7

16: Trigger Out

Lamp

Fan

RS-232C

17: Baud Rate

Menu items

4 Special

5 Through

• Subtitle Zoom

Subtitle Area

V Scroll

• Cinema Zoom

• Cinema Squeeze

• 14:9 Zoom

(For video type input signal)

• Normal Through

• Squeeze Through

6 Monotone

7 Color

• Menu Brightness

• Menu Contrast

• Menu Brightness

• Menu Contrast

• Color Style

Memo

• In addition to color temperature adjustment, the color coordinates and gain adjustment for each color may be carried out at the

[WRGB] and [WRGBYCM] color selection screen. Refer to page 42 and 43 for more information.

•You can select [Subtitle Area] and [V Scroll] from the [Subtitle Zoom] menu item. See page 45 and 46 for more information.

1 Standard

2 WRGB

• Color Temp.

• Color selection screen

Color coordinate

Gain

3 WRGBYCM

● Image

1: Color Adjustment

Standard

WRGB 2

WRGBYCM 3

2: Level Adjustment

YPbPr RGB

Y Offset R Offset

Pb Offset G Offset

Pr Offset B Offset

Y Gain R Gain

Pb Gain G Gain

Pr Gain B Gain

● Initial

5: Color System

Auto

NTSC

NTSC4.43

PAL

PAL-M

PAL-N

PAL60

SECAM

6: Input A/B, DVI Signals

Component

RGB PC

RGB TV .etc

• Color selection screen

Color coordinate

Gain

7: Input A/B Sync Type

Auto

Separate Sync

Composite Sync

Sync On Green

8: HDMI Signal

Auto

Component

RGB TV

9: Display Language

English

Deutsch

Español

Français

Italiano

Portuguêsa

10: Lamp Running Time

Yes

11: Reset

All Settings

All Memory

Current Memory

9600bps

19200bps

38400bps

57600bps

115200bps

13_DPX-1300_E.p65 9/20/05, 4:01 PM29

◆ Menu group items and functions

<Image>

You can adjust the image when the unit is receiving an input signal.

Black Level

(Input signal)

Video/S-Video/Component/RGB TV

Contrast

(Input signal)

RGB PC

Gamma

(Input signal)

Video/S-Video/Component/RGB TV/RGB PC

Brightness

(Input signal)

RGB PC

White Level

(Input signal)

Video/S-Video/Component/RGB TV

Output signal

Input signalBlack White

White

Output signal

Input signalBlack White

White

Menu items

Output signal

Input signalBlack White

White

white level

Output signal

Input signalBlack White

White

Adjusts the level of darkness (black level) in an image.

Adjusts the level of darkness without altering peak whiteness levels.

•+ side (0 to +50):

Increases the luminance of dark scenes,

increasing the clarity of shading, but

reducing contrast.

•- side (-50 to 0):

Weakens dark scenes, increasing image

contrast while reducing the clarity of black

shading.

Adjusts the bright areas (white level) in the image.

Changes the brightness of an image without altering the brightness of the black areas of the

image.

•+ side (1.00 to 1.50):

Increases the brightness of white areas in

the image, increasing contrast clarity, but

rendering white shadings difficult to see.

•- side (0.50 to 1.00):

Reduces the contrast of images.

Changes the way the unit responds to changes in the shadings and color

tones of the image.

The unit supplies 10 types of patterns for dealing with these changes. (☞ page 46)

• A-E Provides the same sense of contrast as an ordinary TV monitor. Dark sections

become more muted in the order A

• a-e Provides richer expression of gradations in dark sections. Dark sections become

more muted in the order a

Adjusts the overall brightness of the image.

• Increase luminance (0 to +50):

Setting this figure too high results in a

white saturated image without any black.

• Decrease luminance (-50 to 0)

Setting this figure too low darkens the

entire image.

Adjusts the bright areas (white level) in the image.

Changes the brightness of an image without altering the brightness of the black areas of the

image.

•+ side (0 to +50):

Increases the brightness of white areas in

the image, increasing contrast clarity, but

rendering white shadings difficult to see.

•- side (-50 to 0):

Reduces the contrast of images.

13_DPX-1300_E.p65 9/20/05, 4:01 PM30

English

Menu items

Adjusts the clearness of the image edges.

Increase this figure to render a sharper image or reduce it to give a softer image with less

image noise.

Choices: 0 to 20

Changes the characteristics of the filter used for “Sharpness Gain”

(described above).

When setting the [Sharpness Gain] parameter to render a relatively strong image (closer to

20), increase this figure to enhance clearness of the image or reduce this figure to enhance

softness of the image.

You cannot adjust this parameter if [Sharpness Gain] is set to [0].

Choices: 1 to 20

Hue

(Input signal)

Video/S-Video/Component/RGB TV

Sets the hue or phase of the image.

•+ side (0 to +50) : Shifts the hue towards blue coloration.

•- side (-50 to 0) : Shifts the hue towards red coloration.

Adjusts the degree to which color depth is expressed in the image.

•+ side (+100 to + 150) : The unit projects colors with greater depth.

•- side (+50 to +100) : The unit projects colors with less depth.

Color Adjustment

(Input signal)

Video/S-Video/Component/

RGB TV/RGB PC/D4 VIDEO

Sharpness Gain

(Input signal)

Video/S-Video/Component/RGB TV

Sharpness Type

(Input signal)

Video/S-Video/Component/RGB TV

Saturation

(Input signal)

Video/S-Video/Component/RGB TV

Adjusts color balance.

There are three menus, [Standard], [WRGB], and [WRGBYCM], separated in order of

complexity from simple to detailed. By the default setting, the DPX-1300 automatically

selects BT709 (RGB color coordinate for High-Definition Television) for HDTV (High-

Definition Television) or PC video input and BT601 (RGB color coordinate for Standard

Television) for SDTV (Standard Television) input. Refer to page 42 for parameter operation

methods.

The present color temperature setting is displayed to the right of the menu items.

- Standard

Adjusts color temperature and hUV

only. hUV adjusts values within the

maximum color temperature limits of the

projector.

Color Temp.

(Input signal)

Video/S-Video/Component/RGB TV/RGB PC

Adjusts color temperature.

Adjusts the level of white in colors between red

and blue, and between green and magenta.

Increase the color temperature to increase the

amount of blue in an image, giving bright color

tones. Reduce the color temperature to increase

the amount of red, giving a darker, more relaxed

atmosphere to the image.

Choices: 5,000 to 10,000

White Correction

(Input signal)

Video/S-Video/Component/RGB TV/RGB PC

Adjusts hUV.

Increasing the hUV setting increases the amount

of green in the image. Decreasing this setting

increases the amount of magenta.

Choices: -0.02 to +0.02

0.5

0.0

0.0 0.5 x

W (Color

temperature

and h UV)

Color Adjustment Standard

6700K

0.000uv

The current color temperature is displayed.

Color temprature

adjustment

–

hUV

13_DPX-1300_E.p65 9/20/05, 4:01 PM31

Menu items

- WRGB

Adjusts the color temperature, the color

coordinates and gain for the three primary

colors, R(Red), G(Green), and B(Blue).

The unit sets the complemental colors

Y(Yellow), C(Cyan), and M(Magenta)

automatically. Adjusting [Color Temp.]

resets the RGB gain based on color

coordinate settings. Adjusting [Gain] resets

[Color temp.] based on color coordinate

settings. Use the color temperature fixed

mode if you want to adjust the RGB

coordinates while keeping the color

temperature setting unchanged. Refer to

“ Example: Using the color temperature

fixed mode” on page 43 for operation

methods.

- WRGBYCM

Adjusts the color coordinates and gain

for each component color individually.

When you have selected WRGBYCM

in the color adjustment submenu, press

RESET to automatically adjust the

RGB gain and YCM color balance to

the most appropriate setting, based on

color temp and RGB color balance

settings.

Iris

(Input signal)

Video/S-Video/Component/RGB TV/RGB PC

Adjusts the iris (Optical).

You can select 3 levels.

Level Adjustment

(Input signal)

Component/RGB TV/RGB PC

Adjusts the analog input signal gain and offset settings.

Adjust the gain and offset for component and RGB (Y, C

B, CR/R, G, B) input signals.

Choices: -50 to 0 to +50 (except for HDMI signals)

White Peaking

Enhances the brilliance of the white portions of the projected image.

Choices: 0 to 5

0.5

0.0

0.0 0.5 x

W (Color temperature

and h UV)

G (Green)

R (Red)

B (Blue)

0.5

0.0

0.0 0.5 x

W (Color temperature

and h UV)

Y (Yelow)

R (Red)

B (Blue)

M (Magenta)

G (Green)

C (Cyan)

OpenClose

Choices: White correction : -0.02 to +0.02

Color temperature : 5,000 to 10,000

Gain : 0.00 to 1.99

Color Adjustment

(continued)

(Input signal)

Video/S-Video/Component/

RGB TV/RGB PC/D4 VIDEO

13_DPX-1300_E.p65 9/20/05, 4:01 PM32

English

Menu items

◆ Signal

You can adjust the image when the unit is receiving an input signal.

Display Aspect Ratio

(Input signal)

Video/S-Video/Component/RGB TV/RGB PC

Sets the aspect ratio for projecting an image from an input signal.

See “Selecting a display aspect for projecting images”, page 22.

Overscan

(Input signal)

Video/S-Video/Component/RGB TV

Overscans video input sources for display.

Selects from [Standard] and [Full]. This parameter is not available when you select [Smart

Zoom] in [Display Aspect]. In some cases, noise may appear at the edges of the image

when you select [Full].

• [Standard] : approximately 94% video output ratio

• [Full] : approximately 100% video output ratio

3D Y/C Separation

(Input signal)

Video(NTSC)

Adjusts the quality of images input from VIDEO jack.

Suppresses the rainbow-like color and annoying dots in images. This function is only

available for NTSC format signals the unit receives at its composite input jacks.

Choices: On/Off

Progressive Mode

(Input signal)

Video/S-Video/Component/RGB TV

Switches the interlace/progressive (I/P) conversion mode.

(Only for interlaced TV signal).

• [Auto] : Detects the video, film and computer graphics (CG) contents and converts into

optimized progressive frames automatically.

•[Video] : Force to convert using motion-adaptive I/P conversion for video contents only.

• [Film] : Force to convert using pulldown I/P conversion for film or CG contents

only. Not recommended to use this mode unless a content consists of the

progressive frames clearly.

Color Space Conversion

(Input signal)

Video/S-Video/Component

Selects color space coefficients.

• [Auto] : Selects the best color space coefficient for the image resolution.

• [SDTV] : Color space coefficient for BT.601 type signal.

• [HDTV] : Color space coefficient for BT.709 type signal.

Setup Level

(Input signal)

Video/S-Video/Component/RGB TV

Compensates for differences in the black levels of images.

•For signals equal to the pedestal level : Set to [0%].

•For signals with high levels of blackness : Set to [7.5%].

100

PEDESTAL LEVEL BLACK LEVEL

13_DPX-1300_E.p65 9/20/05, 4:01 PM33

Menu items

Overshoot Supp. Range

Adjusts the range of the overshoot surpression in the outline of the

projected images.

This function is only available for SDTV and EDTV.

Choices: 1 to 5

Noise Reduction Type

(Input signal)

Video/S-Video/Component/RGB TV

Reduces noise in the images.

Digital processing eliminates noise in the luminance and color signals from sources with a

comparatively large amount of noise, producing a more vivid image. Use when the quality

of th sources you are viewing requres it.

Choices: Off/3DNR/DVNR

• [3DNR] :3D Noise Reduction

This function is only available for SDTV, EDTV, and HDTV.

Reduces noise in the luminance and color signals and random noise by pixel

unit.

•[DVNR] :Digital Video Noise Reduction

This function is only available for SDTV.

Reduces mosquito noise and block noise caused by compression of the digital

video images.

Horiz. Display Position

(Input signal)

RGB PC /Component/RGB TV

(except for HDMI/DVI signals)

Adjusts the horizontal display position of the image.

Choices: -10 to 0 to +10

Vert. Display Position

(Input signal)

RGB PC/Component/RGB TV

(except for HDMI/DVI signals)

Signal Status

Displays the resolution of the image signal the unit is receiving.

Sync signal information for RGB type inputs is also displayed.

Overshoot Supp. Level

(Input signal)

Video/S-Video/Component/RGB TV

Adjusts the level of the overshoot surpression in the outline of the projected

images.

This function is only available for SDTV and EDTV.

Choices: Off/1/2/3

Noise Reduction Level

(Input signal)

Video/S-Video/Component/RGB TV

Adjust the level of the noise reduction.

Choices: 1/2/3/4

Adjusts the vertical display position of the image.

Choices: -5 to 0 to +5

(Input signal)

Video/S-Video/Component/RGB TV

Signal Level

(Input signal)

RGB TV (HDMI/DVI signals only)

Select the range of the black level and white level in the input signal for HDMI

and DVI signals.

This function is only available when RGB TV is selected.

Choices: 16 to 235/0 to 255

13_DPX-1300_E.p65 9/20/05, 4:01 PM34

English

◆ Initial

Menu items

Color System

Selects the color system to use for video input signals.

Usually, set this parameter to Auto to have the unit automatically detect the signal and

select an appropriate color system. Set the unit manually to view NTSC4.43 images as it

cannot detect NTSC4.43 automatically.

Choices: Auto/NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM

INPUT A Sync Type

Selects the sync type for signals received at INPUT A.

This function is only available for RGB TV.

Choices: Auto/Separate Sync/Composite Sync/Sync on Green

INPUT A Signal

Selects the type of input signal received at INPUT A.

Choices: Component/RGB PC/RGB TV

INPUT B Sync Type

Selects the sync type for signals received at INPUT B.

This function is only available for RGB TV.

Choices: Auto/Separate Sync/Composite Sync/Sync on Green

HDMI Signal

Selects the signal type received at the HDMI jack.

Choices: Auto/Component/RGB TV

Auto Input Search

Automatically changes inputs when the unit does not receive a signal.

If the signal the unit is currently receiving stops, or the input signal you selected the last

time you used the unit does is not available when you turn the unit power on, it

automatically searches through inputs for a signal in the following order.

INPUT A INPUT B D4 VIDEO S VIDEO VIDEO HDMI

DVI INPUT A

Choices: On/Off

Display Language

Selects the language used in the menu display.

Choices:

/English/Deutsch/Español/Français/Italiano/Portuguêsa/ /

Reset

Resets menu settings to the factory presets.

Resets all the settings to the factory presets, and return the configurations stored in the

memory to the factory presets. See page 44, 53 and 54 for the operational procedure.

• [All Settings] : Return all settings in the [Initial] and [Setup] menu groups in the

main menu, and all configurations stored by the memory function, to

the factory presets.

• [All Memory] : Return all configurations stored by the memory function to their

default settings.

• [Current Memory] : Return the currently selected memory configuration (corresponding

to the signal input from the currently selected input jack) to their

default settings.

Lamp Running Time

Displays the total lamp running time.

Opens the submenu to reset the running time. See page 45 for the operational procedure.

INPUT B Signal

Selects the signal type received at INPUT B.

Choices: Component/RGB PC/RGB TV

Auto Power Off

If the signal the unit is currently receiving stops and you do not perform any

operations for 30 minutes or more, the unit automatically places itself in

standby mode.

Choices: On/Off

DVI Signal

Selects the signal type received at the DVI jack.

Choices: RGB PC/RGB TV

13_DPX-1300_E.p65 9/20/05, 4:01 PM35

Menu items

◆ Setup

Location

Designate the location of the main unit.

Choices: [Front/Table] [Front/Ceiling] [Rear/Table] [Rear/Ceiling] (☞ page 12)

V Keystone Correction

Adjusts the projection angle of the image.

If you do not install the projector at right angles to the screen, the image will be trapezoidally

distorted. You can electronically correct this distortion using this function to adjust the width

without changing the height of the image. Increase the keystone value (0 to +50 ) when the

upper part of the image is overly wide, and reduce it (-50 to 0 ) when the lower part is overly

wide.

Remote Control Sensor

Sets the remote control sensor.

The main unit has two remote control sensors, one on the front panel and one on the rear,

which this setting allows you to switch between. The remote control functions regardless of

the setting of this parameter if you use a wired connection to connect it to the main unit.

Choices: Front & Rear/Front/Rear/Off

Remote Control ID

Sets the remote control ID.

Selects ID1 or ID2 for each main unit when operating two main units with one remote

control. You can select the controllable main unit with the remote control code switch on

the remote control.

Choices: ID1/ID2

Lamp Power

Lowers the power supply to the lamp.

You can adjust the power supplied to the lamp within the range of 80 to 100%.

Lens Adjustment Lock

Locks the lens adjustment function.

Locks the lens so that you cannot change the V.POS, ZOOM, and FOCUS settings

accidentally when set to [ON]. Set to [OFF] to cancel this function.

When the upper part of

the image is wider than the lower part

Increase the value

in the positive (+) direction

Decrease the value

in the negative (-) direction

When the lower part of

the image is wider than the upper part

H Keystone Correction

Adjusts the projection angle of the image.

If you do not install the projector at right angles to the screen, the image will be trapezoidally

distorted. You can electronically correct this distortion using this function to adjust the height

without changing the width of the image. Increase the keystone value (0 to +50 ) when the right

side of the image is overly high, and reduce it (-50 to 0 ) when the left side is overly high.

Increase the value

in the positive (+) direction

Decrease the value

in the negative (-) direction

When the right side of

the image is higher than the left side

When the left side of

the image is higher than the right side

13_DPX-1300_E.p65 9/20/05, 4:01 PM36

English

Menu Color

Trigger Out

Sets the TRIGGER OUT terminal.

Set the external control TRIGGER OUT jack 12 V signal emission to [Lamp] to

synchronize it to the ON/OFF state of the lamp, to [Fan] to synchronize it to the fan, and to

[RS-232C] to receive ON/OFF signals through the RS-232C terminal.

Choices: Lamp/Fan/RS-232C

Baud Rate Sets the transmission speed of the RS-232C terminal.

This setting becomes valid from the next time you switch the unit on.

Choices: 9600bps/19200bps/38400bps/57600bps/115200bps

Message

Selects whether to display memory number, input signal and other

information on the projection screen. (☞ page 62)

Choices: On/Off

Selects the color of the letters and background the main unit uses to display

the menu on screen.

You can choose to display the menu screen in [Monotone] or [Color]. Also, you can adjust

the contrast and brightness of the menu from the [Menu Brightness] and [Menu Contrast]

menus. You can select from 3 color types.

Monotone Menu Brightness

Menu Contrast

Color Menu Brightness

Menu Contrast

Color Style

Menu items

Choices: Menu Brightness :-10 to 0 to +10

Menu Contrast : 0.50 to 1.50

13_DPX-1300_E.p65 9/20/05, 4:01 PM37

Menu operations

◆ Operation button functions

Use the buttons on the remote control or the main unit to operate the menus. The button functions are listed below.

1 Menu Button

Opens/Closes the menu.

2 Cursor button

+ / - (Move the cursor ringht/left)

• Selects menu groups.

• Opens/Closes submenus.

• Selects/Changes settings.

h / g (Moves the cursor up/down)

• Selects menu items.

• Selects/Changes settings.

3 button

• Confirms setting changes.

• Opens the in-line menu when the menu is not open.

• Selects special operation (☞ page 42) and memory operation. (☞ page 48)

4 ESCAPE button

• Returns the cursor one level up the menu (e.g. From the menu item level to the menu

group level).

• Closes submenus.

• Closes the menu screen when the cursor is in a menu group.

• Returns from the menu movement bar to the menu entry screen, after moving a menu.

5 RESET button (Remote control only)

Returns parameters back to their default settings (Does not affect items with no default

setting).

RESET

123

VIDEO

STILL

HIDE

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

LIGHT

BDVI

S VIDEO

INPUT

MEMORY

HDMI

INPUT

ASPECT

ESCAPE

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE

INPUT

ASPECT

Remote Control

Main Unit

14_DPX-1300_E.p65 9/20/05, 4:01 PM38

English

Menu operations

◆ Menu operations 1 (with no submenu)

Menu operations use the procedure below to adjust menu item without submenus.

1. Press the MENU button to open

the menu screen.

Memo

• If you have opened the menu screen

previously, the menu displays the

settings from the last time you used it.

2. Press the + or - button to select a

menu group.

The illustration at right depicts the [Setup]

group being selected.

Menu items related to the selected menu group are displayed.

You can now adjust the selected item.

Select a menu group (Image / Signal / Initial / Setup)

(Select with the +/- buttons)

Select an item to adjust or a setting

(Select with the h / g buttons)

Choose a setting for the selected item

(Usually, use the +/- buttons)

Remote Control Main Unit

Image

Black Level

a b c d e

Memory 1 VIDEO

White Level 0

Gamma Trim

Hue 0

Saturation 100

Color Adjustment

Level Adjustment

Iris

Signal Initial Setup

White Peaking

Move Menu Window

WRGB

6500K

0.000uv

Sharpness Gain

Sharpness Type

Location

VIDEO

V Keystone Correction 0

Off

Lamp Power

Off OnMessage

Trigger Out

Baud Rate

Front / Table

Front & Rear

Monotone

Lamp

115200bps

ID 1

Image

Memory 1

Signal Initial Setup

Move Menu Window

Menu Color

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

H Keystone Correction 0

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUT

ASPECT

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

INPUT

ASPECT

ESCAPE

Remote Control Main Unit

MENU Button

14_DPX-1300_E.p65 9/23/05, 12:03 PM39

6. To close the menu screen when

you have finished making

adjustments, press the MENU

button.

5. Move to another item or group as

necessary.

Memo

• Press the h or g button to move the

cursor to another item in the same

group.

To move to an item in another menu

group, press the ESCAPE or h button

to return to the top of the menu group,

and repeat steps 2,3 and 4.

Remote Control Main Unit

Menu operations

4. Press the + or - button to select a

suitable setting.

The illustration at right depicts the [Lens

Adjustment Lock] mode set to [On].

Memo

• The setting method depends on the

item selected.

3. Press the h or g button to move

the cursor to the item you wish to

adjust.

The illustration at right depicts [Lens

Adjustment Lock] being selected.

Remote Control

Main Unit

Remote Control Main Unit

Location

VIDEO

V Keystone Correction 0

Off

Lamp Power

Off OnMessage

Trigger Out

Baud Rate

Front / Table

Front & Rear

Monotone

Lamp

115200bps

ID 1

Image

Memory 1

Signal Initial Setup

Move Menu Window

Menu Color

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

H Keystone Correction 0

Location

VIDEO

V Keystone Correction 0

Off

Lamp Power

Off OnMessage

Trigger Out

Baud Rate

Front / Table

Front & Rear

Monotone

Lamp

115200bps

ID 1

Image

Memory 1

Signal Initial Setup

Move Menu Window

Menu Color

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

H Keystone Correction 0

Remote Control Main Unit

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUT

ASPECT

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

INPUT

ASPECT

ESCAPE

Remote Control Main Unit

ESCAPE Button

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUT

ASPECT

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. POS

INPUT

ASPECT

ESCAPE

MENU Button

14_DPX-1300_E.p65 9/20/05, 4:01 PM40

English

Menu operations

◆ Menu operations 2 (with submenus)

Use the procedure below to adjust menu items that contain submenus.

1. Carry out steps 1 to 3 from “Menu

Operations 1” to select the menu

item you want to set.

The illustration at right depicts [Display

Language] in the [Initial] group selected.

Memo

•“” appears to the right of items that

contain a submenu.

Remote Control Main Unit

Color System

VIDEO

INPUT A Signal

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

Auto Power Off

Auto Input Search

Display Language

Reset

Auto

Component

Auto

RGB TV

Auto

HDMI Signal Component

DVI Signal Component

English

Lamp Running Time 0 Hour

OnOff

Off On

Image

Memory 1

Signal Initial Setup

Move Menu Window

Italiano

Portuguêsa

Français

Español

Deutsch

English

VIDEO

Display Language

Image

Memory 1

Signal Initial Setup

Move Menu Window

VIDEO

Italiano

Portuguêsa

Français

Español

Deutsch

English

2. Press the + button to move to the

submenu.

Memo

• Some menu items contain other items

that you can select. In such cases,

move to the lower level submenu

using the + button.

3. Press the h or g button to adjust

item settings.

Memo

• When “ : Fix” appears in the

operations guide at the bottom left of

the menu screen, press the button

to confirm the selected settings.

4. Press the – or ESCAPE button to

return to higher level menu items.

5. To close the menu screen when

you have finished making

adjustments, press the MENU

button.

Items using the

button for setting.

Display Aspect Ratio

Color System

Input A Signal

Input A Sync Type

Input B Signal

Input B Sync Type

HDMI Signal

DVI Signal

Remote Control Sensor

Remote Control ID

14_DPX-1300_E.p65 9/21/05, 3:32 PM41

◆ Special operations

Some items in the menu require special methods to configure.

VIDEOMemory 1

Initial Setup

u Window

Gain 0.82

0.3

0.35

0.6 0.65x

x=0.640 y=0.330

Image Signal

Move Me

: Edit

0.5

0.0

0.0 0.5 x

Red

Example: Adjusting R (Red)

The name of the

selected item appears

here.

Use the h, g, +, or -

button to select an

item.

Press the button.

Press the ESCAPE

button.

Color coordinate

display area

Color coordinate

adjustment area

Press the button to

change the item to adjust.

Gain setting

display area

Gain adjustment

area

Menu operations

1. Select [Color Adjustment] in the [Image] group from the main menu.

2. Press the + button to enter submenus.

3. Select a suitable item from [Standard] • [WRGB] • [WRGBYCM] using the h or g button, and

press the + button.

This explanation uses the [WRGBYCM] menu as an example.

4. Press the h, g, +, or - button to select the item you wish to configure from the color scale, and

press the

button.

The Color coodinate adjustment area on the right side of the menu screen will be highlighted.

5. Press the h, g, +, or - button to adjust the setting for the item.

6. If you select R (red), G (green), B (blue), Y (yellow), C (cyan), or M (magenta) in step 4, press the

button to move to the gain adjustment area, and press the + or - button to adjust the gain.

7. Press the ESCAPE button to return to the color scale.

Memo

• See page 32 for datails about each color item.

14_DPX-1300_E.p65 9/20/05, 4:01 PM42

English

Menu operations

1. Select [Color Adjustment] in the [Image] group from the main menu.

2. Press the + button to enter submenus.

3. Select [WRGB] from the [Standard], [WRGB], [WRGBYCM] using the h or g button, and press

the + button.

4. Press the h, g, +, or - button to select W (Color temperature and h UV) from the color scale,

and press the

button.

The color temperature adjustment area on the right side of the menu screen will be highlighted in white.

5. Press the h, g, +, or - button to adjust the color temerature.

6. Press the

button to enter the color temperature fixed mode.

The “ ” icon appears on the W (Color temperature and h UV ) box.

• In this mode, you cannot use the h, g, +, or - button to change the color temperature. If you try to change,

“The color temperature is fixed.” appears at the bottom of the menu screen.

7. Press the ESCAPE button to return to the color scale. Follow steps 4 to 5 in the “Example:

Adjusting R (Red)” on page 42 to adjust the color coordinates.

• When using the color temperature fixed mode, the gain adjustment area will not be displayed.

•To cancel the color temperature fixed mode, select the W (Color temperature and h UV) box and press the

button until the “ ” icon disappeares.

The name of the

selected item appears

here.

When this unit is in

the color temperature

fixed mode, the “ ”

icon appears on this

W (Color temperature

and h UV) box.

Press the button.

When this unit is in the

normal mode, the “ ”

icon dissapears.

Use this mode when you want to adjust the RGB coordinate while keeping the color temperature setting unchanged.

Example: Using the color temperature fixed mode

Image Signal

Move Men

ESCAPE : Return

0.5

0.0

0.0 0.5 x

Color Temp.

Image Signal

Move Men

ESCAPE : Return

0.5

0.0

0.0 0.5 x

Color Temp.

Memo

Press the button.

Example:

Color temperature fixed mode

Example:

Normal mode

14_DPX-1300_E.p65 9/21/05, 3:32 PM43

Reset the selected settings to the default settings.

VIDEOESC : Return

Image

Memory 1

Signal Initial Setup

Move Menu Window

VIDEO

Image

Memory 4

Signal Initial Setup

Move Menu Window

Press " " to reset

to factory settings.

ESC : Return

1. Select the item you wish to reset to the default setting

from the main menu.

2. Press the RESET button on the remote control to reset

to the default setting (resetting does not affect items

with no default setting).

Memo

• The RESET button has a special function when selecting

[WRGBYCM] in [Color Adjustment]. (☞ page 32)

• The RESET button resets the parameters to their default

settings (corresponding to the signal input: HDTV or SDTV)

when the Color coordinate adjustment area is selected after

selecting [WRGB] or [WRGBYCM] in [Color Adjustment]. (☞

page 32)

1. From the menu screen, select [Initial] [Reset]

[All Settings].

Reset all of your settings to its factory presets.

VIDEO+ : Enter

Reset

All Settings

All Memory

Current Memory

Image

Memory 4

Signal Initial Setup

Move Menu Window

2. Press the + button to display a confirmation message.

3. Press the

button to reset to the default settings.

Memo

•To cancel this operation and return to the previous screen,

press the ESCAPE button.

Change the position of the menu on the screen.

1. In the menu screen, press the ESCAPE or h button

and move the cursor to one of the menu groups.

2. Press the h button to enter [Move Menu Window].

3. Use the h, g, +, or - button to move the menu screen

to a location of your choice.

4. Press the ESCAPE button to return to the previous

menu screen.

Menu operations

14_DPX-1300_E.p65 9/20/05, 4:01 PM44

English

Reset the [Lamp Running Time] displayed on screen to “0”.

VIDEO

Special

Image Signal Initial Setup

Move Menu Window

Memory 1

Cinema Zoom

Cinema Squeeze

14:9 Zoom

Subtitle Zoom

+ : Enter

Use the [Subtitle Area] menu to adjust the size of the subtitle display area. Use [V Scroll] to adjust the vertical position of the subtitle display.

1. From the menu screen, select [Signal] [Display

Aspect Ratio]

[Special].

2. Press the + button to enter the lower level selection

menu.

3. Select [Subtitle Zoom] with h or g buttons.

4. Press the

button.

“

” appears to the right of [Subtitle zoom].

Memo

• After the first time you carry out this procedure, “ ” appears

beside [Subtitle Zoom] automatically.

1. From the menu screen, select [Initial] [Lamp

Running Time].

: Fix

Yes

VIDEO

Image

Memory 4

Signal Initial Setup

Move Menu Window

Lamp Running Time 12 Hours

Press " " to reset lamp running time.

Color System

VIDEO

INPUT A Signal

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

Auto Power Off

+ : Enter

Auto Input Search

Display Language

Reset

Auto

Component

Auto

RGB TV

Auto

DVI Component

HDMI Signal Component

English

Lamp Running Time 12 Hours

OnOff

Off On

Image

Memory 1

Signal Initial Setup

Move Menu Window

2. Press the + button to open the confirmation screen.

3. Press the h or g button to select [Yes].

4. Press the button to confirm.

Memo

•To cancel the operation and return to the menu screen, select

[No].

Menu operations

14_DPX-1300_E.p65 9/20/05, 4:01 PM45

5. Press the + button to enter the lower level selection

menu.

6. Press h or g button to select [Subtitle Area] or [V

Scroll].

7. Press the + or – button to select a suitable setting.

Memo

• Press the h or g button to move to a different menu item in

the [Subtitle Zoom] menu.

8. Press the ESCAPE button to return to the higher level

selection menu.

VIDEO

Image Signal Initial Setup

Move Menu Window

Memory 1

ESC : Return

Subtitle Area

V Scroll

Subtitle Zoom

Press the button

1. From the menu screen, select [Image] [Gamma].

2. Press the button to switch between capital (A to E)

and non capital (a to e) letters.

3. Use the + or – button to select an appropriate setting.

Select a gamma control pattern (color tone characteristics) from the 10 preset patterns. (☞ page 30)

Image

Black Level

A B C D E

Memory 1 VIDEO

White Level 0

Gamma

Hue 0

Saturation 100

Color Adjustment

Level Adjustment

Iris

Signal Initial Setup

White Peaking

Move Menu Window

WRGB

6500K

0.000uv

: Exchange

Sharpness Gain

Sharpness Type

Image

Black Level

a b c d e

Memory 1 VIDEO

White Level 0

Gamma

Hue 0

Saturation 100

Color Adjustment

Level Adjustment

Iris

Signal Initial Setup

White Peaking

Move Menu Window

WRGB

6500K

0.000uv

: Exchange

Sharpness Gain

Sharpness Type

Menu operations

14_DPX-1300_E.p65 9/20/05, 4:01 PM46

English

◆ Adjusting image quality using the inline menu

Use the inline menu to adjust image quality without obstructing the image during projection. See “Menu group items and functions” (page 30

- 37) for information on each setting.

Black Level

Inline menu item

Indicates that you can use the h and g buttons to

change the position of the inline menu.

Press the + or - button to set the item to an appropriate setting.

Press the RESET button to return the item to its default setting.

<Example: Using the inline menu>

1. Press the button when the menu is not open.

Image menu items appear one at a time in the lower area of the screen. If you do not carry out any operations within 5 seconds, the menu

disappears.

Press the h or g button to select an item to set.

2. To close the menu when you have finished making adjustments, press the ESCAPE button.

Memo

• Press the button to change between the pages of the [Gamma] menu.

Black Level

Gamma

A B C D E

Gamma

A B C DE

Parameter adjustment area

The menu items available may differ depending on the input signal type.

Memo

• When [Sharpness Type] is set to [0], the [Sharpness Gain] adjustment cannot be performed.

Black Level

White Level

Gamma

Hue

Saturation

Color Temp.

White Correction

Sharpness Gain

Sharpness Type

White Peaking

Iris

For video type sources

Brightness

Contrast

Gamma

Color Temp.

White Correction

White Peaking

Iris

For PC type sources

Menu operations

15_DPX-1300-E.p65 9/20/05, 4:01 PM47

The memory function automatically saves the settings of menu items listed in the “Items to be saved” table below.

◆ Memory configurations

The DPX-1300 stores up to six sets of configurations, called memory numbers, for each input jack. For each memory number, the DPX-

1300 stores specific configurations for each signal type, giving a total of 90 configurations.

◆ Recalling a memory number

◆ Saving memory settings

All memory numbers have default settings. Since the DPX-1300 saves any changes in the menu item to the current memory number, you do

not need to save the settings each time. To preserve the specific settings, use the “Memory lock” function (☞ See page 50).

1. Select the [Image] or [Signal]

group from the menu screen.

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUT

ASPECT

PATTIRIS

AUTO

SETTING

ZOOM FOCUSV. PO S

INPUT

ASPECT

ESCAPE

Remote Control Main Unit

MENU Button

1. Press the MEMORY button (in the

MEMORY area) of which you want

to recall the settings.

Remote Control

456

123

VIDEO

STILL

LIGHT

B DVI

S VIDEO

INPUT

MEMORY

HDMI

MEMORY area

Memory configurations for each input jack Items to be saved

Image

Black Level (Brightness)

White Level (Contrast)

Gamma

Hue

Saturation

Color Temp.

White Correction

Sharpness Gain

Sharpness Type

Color Adjustment

White Peaking

Iris

Level Adjustment

Signal

3D Y/C Separation

Progressive Mode

Color Space Conversion

Setup Level

Overshoot Supp. Range

Overshoot Supp. Level

Noise Reduction Type

Noise Reduction Level

Horiz. Display Position

Vert. Display Position

Signal Level

Memory function

(Save, Recall, Lock, Copy, Reset)

Input Signal Type

Input

VIDEO

S VIDEO

INPUT A

INPUT B

HDMI

DVI

The Number of Memories

–

SDTV

HDTV

RGB-PC

SDTV

HDTV

RGB-PC

SDTV

HDTV

SDTV

HDTV

RGB-PC

Total

SDTV

HDTV

15_DPX-1300-E.p65 9/20/05, 4:01 PM48

Memory function

English

2. Press the g button to select

“Memory number status” from

the bottom of the screen.

3. Press the + button to open the

submenu.

5. Press the

button to recall the

settings in the selected memory.

4. Press the h or g button to select

a memory number.

Memo

• When the unit receives a signal with a different resolution from the same input jack,

it detects the new resolution and recalls an appropriate memory settings.

a b c d e

Memory 1 VIDEO

100

WRGB

+ : Enter

Image Signal Initial Setup

Move Menu Window

Black Level

White Level

Gamma Trim

Hue

Saturation

Level Adjustment

Iris

Color Adjustment

White Peaking

6500K

0.000uv

Sharpness Gain

Sharpness Type

Memory 6 VIDEO

Memory 5

Memory 4

Memory 3

Memory 2

Memory 1

: Fix

Image Signal Initial Setup

Move Menu Window

Memory number status

Remote Control Main Unit

15_DPX-1300-E.p65 9/20/05, 4:01 PM49

◆ Memory lock

The lock function protects information in a memory not to be overwritten. You can set the lock function for each memory number, and

additionally for each SDTV/HDTV/RGB-PC input.

1. Recall the memory number you

wish to lock.

2. Select a memory number status.

3. Press the button.

“ ” appears beside locked memory

numbers.

Remote Control Main Unit

a b c d e

Memory 1 VIDEO

100

WRGB

Image Signal Initial Setup

Move Menu Window

Black Level

White Level

Gamma Trim

Hue

Saturation

Level Adjustment

Iris

Color Adjustment

White Peaking

6500K

0.000uv

Sharpness Gain

Sharpness Type

1. Select the memory number you

wish to unlock.

2. Select a memory number status.

3. Press the button.

“

” disappears from the memory status

screen and the memory lock is removed

from the memory number you selected.

Remote Control Main Unit

a b c d e

Memory 1 VIDEO

100

WRGB

+ : Enter

Image Signal Initial Setup

Move Menu Window

Black Level

White Level

Gamma Trim

Hue

Saturation

Level Adjustment

Iris

Color Adjustment

White Peaking

6500K

0.000uv

Sharpness Gain

Sharpness Type

Memo

•You can change settings when the memory is locked, but the unit does not save the changes to a memory. Any changes you make

are erased when you place this unit to standby mode. (The memory number status color changes from white to gray if you change

any menu items while the memory is locked.)

“ ”disappears

“ ”appears

15_DPX-1300-E.p65 9/22/05, 6:19 PM50

Memory function

English

1. Recall the memory number to be

the copy source.

◆ Memory copy

Copy the settings stored in a memory number to another memory number.

a b c d e

Memory 1 VIDEO

100

WRGB

+ : Enter

Image Signal Initial Setup

Move Menu Window

Black Level

White Level

Gamma Trim

Hue

Saturation

Level Adjustment

Iris

Color Adjustment

White Peaking

6500K

0.000uv

Sharpness Gain

Sharpness Type

2. Press the g button to select

“Memory number status” from

the bottom of the screen.

Remote Control Main Unit

Memory number status

3. Press the + button to open the

submenu.

Remote Control Main Unit

Memory 6 VIDEO

Memory 5

Memory 4

Memory 3

Memory 2

Memory 1

: Fix

Image Signal Initial Setup

Move Menu Window

4. Press the h or g button to select

a memory number to be the copy

destination.

•You cannot select a source memory

number (gray colored) as a copy

destination.

•You cannot select a locked memory

number (marked “ ”) as a copy

destination.

Remote Control

Main Unit

Memory 6 VIDEO

Memory 5

Memory 4

Memory 3

Memory 2

Memory 1

: Fix

Image Signal Initial Setup

Move Menu Window

: Copy

Memo

15_DPX-1300-E.p65 9/20/05, 4:01 PM51

5. Press the + button to display the

confirmation screen.

Remote Control

Main Unit

Memory 6 VIDEO

Memory 5

Memory 4

Memory 3

Memory 2

Memory 1

: Fix

Image Signal Initial Setup

Move Menu Window

Copy the Memory?

Press to confirm.

Yes

6. Press the h or g button to select

[Yes] .

Remote Control

Main Unit

Memory 1 VIDEO

: Fix

Image Signal Initial Setup

Move Menu Window

Copying to Memory 3 ...

7. Press the button.

The settings stored in the source memory

number are copied to the destination

memory number.

If the copy is complete, the memory status

screen dislplays the memory number

selected in step 1.

Remote Control

Main Unit

15_DPX-1300-E.p65 9/20/05, 4:01 PM52

Memory function

English

VIDEO

Image

Memory 4

Signal Initial Setup

Move Menu Window

ESC : Return

Press " " to reset current memory.

1. From the main menu, select

[Initial]

[Reset] [Current

Memory].

VIDEO+ : Enter

Reset

All Settings

All Memory

Current Memory

Image

Memory 4

Signal Initial Setup

Move Menu Window

2. Press the + button to display the

confirmation screen.

3. Press the

button to reset the

settings to their default settings.

Remote Control Main Unit

◆ Resetting to the default settings in the memory menu

Reset the settings stored in the memories to the default settings.

Follow the procedure below to revert settings stored in the selected memory (corresponding to the signal input from the currently selected

input jack) to their default settings.

15_DPX-1300-E.p65 9/20/05, 4:01 PM53

Reset all the settings in the memories to their default settings regardless of the input jack or input signal.

1. From the main menu, select

[Initial]

[Reset] [All

memory].

VIDEO

Reset

+ : Enter

All Settings

All Memory

Current Memory

Image

Memory 4

Signal Initial Setup

Move Menu Window

2. Press the + button to display the

confirmation screen.

3. Press the

button to reset the

settings to their default settings.

Remote Control Main Unit

VIDEO

Image

Memory 4

Signal Initial Setup

Move Menu Window

Press " " to reset

all Memory.

ESC : Return

15_DPX-1300-E.p65 9/20/05, 4:01 PM54

Reference

English

Glossary

The following is a list of key words used in the use of projectors and image signals and their explanations. Please refer to it when using this

manual. For an explanation of vocabulary used in the menu, refer to "Menu group items and functions” ( ☞ page 30 - 37).

Reference

Ceiling mount bracket

The mounting hardware used to hang this unit from the ceiling.

Two types of bracket are available, for high and low ceilings.

Ceiling mount brackets are sold separately.

Cinemascope size

The widest film format in 70 mm film, with an aspect of 2.35:1.

Color spacing

The conversion of YUV color separated signal to RGB signal.

There are two formats for this, BT.601 for SDTV, and BT.709 for

HDTV. This unit switches between them as required.

Component video signal

A method of sending video signals with independent luminance

and color signals. Component video gives a higher image quality

than ordinary composite video because it bypasses mixing and

separating circuits. Component video signal consists of three lines,

the luminance signal (Y), and two color difference signals (P

B/CB,

R/CR).

Composite video signal

The most common type of video signal, combining luminance and

color signals in one line. This method requires mixing and

separating processes on both the send and receive sides. Use a pin

cable for connection.

DLP

technology

Digital Light Processing, an image display engine used in

projectors that use the DMD™ chip developed by Texas

Instruments.

DVI terminal

A digital RGB/Component signal is sent differently from a

computer or A/V equipment to this terminal. A 24-pin connector

and cable are used.

D terminal

A cable that allows transmission of all of the signals in composite

video in one cable. This method is used for transmitting image

signals between the latest AV components. There are 5 methods of

transmission, D1-D5. This unit is compatible with D4.

EDTV

Extended-Definition Television, a term used to define systems that

satisfy the following conditions:

•A resolution of 480p or 576p (p stands for progressive scans)

•A 4:3 or 16:9 aspect ratio

HDCP

A technique designed to protect the video transmission between a

DVI or HDMI transmitter and a display device.

HDMI

High-Definition Multimedia Interface, a method of differentially

transmitting digital RGB/component video signal from computers

and home digital equipment.

HDTV

High-Definition Television, a term used to define systems that

satisfy the following conditions:

•A vertical resolution of 720p or 1080i (p stands for progressive

scans, i stands for interlace scans)

•A 16:9 aspect ratio

Interlace

The most common type of scanning used in televisions. It divides a

screen into even and odd numbered fields for scanning, and then

builds an image by combining them into one image (frame).

Keystone Correction

Using the unit at an angle to the screen distorts the projected image

trapezoidally. You can use V Keystone Correction or H Keystone

Correction to electronically correct this distortion.

Letterbox

A method of converting the content of landscape oriented film to a

4:3 signal. You can watch landscape images without trimming them

by adding a black bar to the top and bottom of the screen, however

this sacrifices vertical resolution to some extent.

Progressive

A method of displaying all scanning lines in a frame at once,

reducing flicker noticeable on a larger screen and creating a sharp,

smooth image. This unit uses progressive scanning for progression.

RGB Signal

A method of transmitting color information using a numeric

representation of the primary colors red, green, and blue separately.

When received, it is expressed in various colors by adding a mixing

colors. RGB is widely used for sending and receiving color images

between computers, and requires horizontal and vertical sync

signals.

SDTV

Standard-Definition Television, a term used to define systems that

satisfy the following conditions:

•A resolution of 480i or 576i (i stands for interlace scans)

•A 4:3 or 16:9 aspect ratio

Smart zoom

Expands the left and right sides of a 4:3 image without altering the

center, when you are attempting to project a 4:3 image on a wide

screen format. This creates some distortion at both edges.

Squeeze

A method of compressing film images horizontally to an aspect of

ratio of 4:3 when recording to video medium. The raw image is

oblong, so needs to be passed through a desqueezing circuit to be

projected in it’s original form.

Standby

The state in which the circuit that receives infrared-signals from the

remote control is active, but all other main circuits are turned on.

The unit consumes a small amount of power in this state.

S Video signal

S stands for Separate. A method of sending signals with separate

luminance (Y) and color (C) signals. Use a 4-pin mini DIN

connector and cable for connection.

16_DPX-1300_E.p65 9/21/05, 9:52 AM55

Compatible signal types

Sync.

Computers output signals with a given regular frequency, which

you must synchronize the projector to in order to produce a good

quality image. If you do not match the phase of the signal, the

image may be flickery, faded, or distorted.

Test pattern

This unit contains test patterns which you can use to adjust the

position and focus of the projected image on the screen.

Tracking

Computers output signals with a given regular frequency, which

you must synchronize the projector to in order to produce a good

quality image. If you do not match the phase of the signal, vertical

stripes may appear on the image.

Vista size

A standard film size, with an aspect ratio of 1.85:1 in North

America, and 1.66:1 in Europe.

3-2 pulldown detection style IP conversion

A function for directly converting interlace signal into sixty frame

progressive signal used when receiving 60 field interlace signal

from an image source recorded with the same 24 frames as movie

film. This allows DVD and other materiel recorded with 24 frames

to be projected on large screens as a natural, precise image with no

loss of quality, comparable to a movie film.

* DLP

, DMD

, DarkChip2

, and DarkChip3

are registered

trademarks of the Texas Instruments corporation of America.

* HQV

, Hollywood Quality Video

and HQV powered by

Teranex

are trademarks of Silicon Optix inc.

* HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademark of HDMI

Licensing LLC.

*The “HD ready” Logo is a trademark of EICTA.

The following tables show the types and formats of signals the DPX-1300 can project. Signals other than those listed here may not be

projected correctly.

◆ TV format 1 (Composite or S Video signals received at the VIDEO or S-VIDEO jack)

fsc

(MHz)

Color systemSignal type

V active

(lines)

f (V)

(Hz)

NTSC 480 59.94 3.580 NTSC

PAL 576 50.00 4.430 PAL

SECAM 576 50.00 4.406, 4.250 SECAM

PAL60 480 59.94 4.430 PAL

NTSC4.43 480 59.94 4.430 NTSC

PAL-M 480 59.94 3.580 PAL

PAL-N 576 50.00 3.580 PAL

◆TV Format 2 (Component/RGB TV signals received at the INPUT A and B, or component signals received at the D4 jack)

Signal type

480i

576i

480p

576p

720p/50Hz

720p/60Hz

1080i/50Hz

1080i/60Hz

H active

(pixels)

720

1280

1920

V active

(lines)

576

480

576

720

1080

f (H)

(kHz)

15.734

15.625

31.469

31.250

37.500

44.955

28.125

33.716

f (V)

(Hz)

59.940

50.000

59.940

50.000

59.940

50.000

59.940

Glossary

16_DPX-1300_E.p65 9/20/05, 4:01 PM56

Reference

English

◆DVI Format (RGB signals input from the DVI jack)

◆PC Format (Analog RGB PC signals received at the INPUT A or B jack)

(*1) VESA is a registered trademark of the Video Electronics Standards Association.

(*2) Macintosh is a registered trademark of the Apple Computer corporation.

1280

720

f (H)

(kHz)

f (V)

(Hz)

Component typeSignal type

V active

(lines)

H active

(pixels)

31.469 59.940 RGBVGA/60Hz 480640

37.879 60.317 RGBSVGA/60Hz 600800

48.363 60.004 RGBXGA/60Hz 7681024

SXGA/60Hz

480p

63.981 60.020 RGB

576p

1024

720

31.469 59.940 RGB

720/60p

480

1280

31.250 50.000 RGB

720/50p

576

44.955

59.940 RGB

1080/60i

720

VESA (*1)

Macintosh (*2)

f (H)

(kHz)

V active

(lines)

H active

(pixels)

Signal type

f (V)

(Hz)

31.469480640VGA/60Hz 59.940

37.861480640VGA/72Hz 72.809

37.500480640VGA/75Hz 75.000

43.269480640VGA/85Hz 85.008

35.156600800SVGA/56Hz 56.250

37.879600800SVGA/60Hz 60.317

48.077600800SVGA/72Hz 72.188

46.875600800SVGA/75Hz 75.000

53.674600800SVGA/85Hz 85.061

48.3637681024XGA/60Hz 60.004

56.4767681024 70.069

◆HDMI Format (Component/RGB signals input from the HDMI jack)

(*3) You cannot select YCBCR4:2:2 mode manually. This mode only available when you set the unit to HDMI Auto mode.

1280

720

1440

1280

f (H)

(kHz)

f (V)

(Hz)

Component type

Signal type

V active

(lines)

H active

(pixels)

31.469 59.940 RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)VGA 480640

15.734 59.940 RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)480i 480(1440) 720

15.625 50.000 RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)576i 576(1440) 720

720

1440

31.469 59.940 RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)480p 480

31.250 50.000 RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)576p 576

37.500 59.940 RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)720/60p 720

1920

44.955 50.000 RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)720/50p 720

1920

33.716 59.940 RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)1080/60i

1080

28.125 50.000 RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)1080/50i

1080

XGA/70Hz

XGA/75Hz

XGA/85Hz

SXGA/60Hz

1024

1280

640

768

1024

480

60.023

68.677

63.981

35.000

75.029

84.997

60.020

66.666

1080/50i

1280

37.500

1920

720

1080

33.716

28.125

50.000

59.940

50.000

RGB

Compatible signal types

16_DPX-1300_E.p65 9/20/05, 4:01 PM57

Maintenance

◆ Regular care

Be sure to disconnect the power cable before doing any maintenance.

Wipe with a soft cloth. Use a damp cloth with a mild detergent and then wipe with a dry cloth again if the unit is heavily soiled. Do not use

strong solvents such as thinner or alcohol as they may damage the unit casing.

<Lens>

Use commercially available blowers or lens tissue to remove any dirt from the lens.

If dust accumulates on the ventilation port filter, the internal temperature of the unit rises, which may cause damage to the unit. Clean the

filter approximately once every 200 hours. Remove the power cable from the AC outlet, and remove dust from the filter with a vacuum

cleaner.

To prevent dust from entering the filter itself, be sure to vacuum the filter with the unit on its side.

◆ Replacing the filter

Replace the filter when it becomes difficult to remove dust from it.

Maintenance

1. Turn off the power and remove the power cable.

2. Carefully place the unit upside down on a soft cloth to prevent scratching.

3. Press the filter hook on the underside of the main unit to remove the filter.

4. Firmly attach the new filter. The lamp does not light if the filter is

incorrectly attached.

Warning

• Contact a YAMAHA dealer or service center if you require replacement filters.

16_DPX-1300_E.p65 9/20/05, 4:02 PM58

Reference

English

◆ Replacing the lamp

The lamp used as a light source in the DPX-1300 is a consumable item which will gradually lose its brightness during the course of use. It is

advisable to replace the lamp when running time has exceeded 2000 hours.

You can check the lamp running time in the [Lamp Running Time] in the [Initial] menu group of the Menu screen. The LAMP warning

indicator will blink when running time exceeds 2000 hours.

There will also be a message displayed on the screen. In this case, follow the instructions below to replace the lamp cartridge. For details on

replacement of lamp cartridges, consult the store where you purchased the DPX-1300.

Warning

• Be sure to use the replacement lamp cartridge PJL-427. Other lamp cartridges are not suitable for use in the DPX-1300.

• If replacing the lamp of the projector that has been installed to the ceiling, you should remove the projector from the ceiling before

replacing the lamp.

• Before starting to replace the lamp cartridge, turn off the power, disconnect the power cable after the fan has completely stopped,

and wait at least one hour for the lamp to cool down.

• Do not remove any other screws than those specified in the following steps.

• The gases inside the lamp contain mercury vapor. Be careful the lamp may break if it gets old or overtasked. The life of a lamp

differs depending on operation environments.

1. Loosen the lamp cover screws.

2. Remove the lamp cover.

3. Loosen the screws of the lamp cartridge.

4. Grip the handle and pull the lamp cartridge to remove it.

5. Insert the new lamp cartridge by reversing the above steps, and tighten

the screws to fix it into place.

6. Replace the lamp cover and secure it with the screws.

The lamp will not turn on if the cover is not securely fastened. Take care

to attach it firmly in place.

7. Connect the unit to the power outlet, turn the unit on, and reset [Lamp

Running Time] on the [Initial] group in the menu. (☞ page 45)

Lamp cover screws

Maintenance

16_DPX-1300_E.p65 9/20/05, 4:02 PM59

Troubleshooting

Cause RemedyProblem

Image is unstable.

The image becomes

cloudy.

Cannot adjust focus or

zoom, or the vertical

position of the lens.

There is condensation on the DPX-1300.

[Lens Adjustment Lock] in the menu is set

to ON.

Switch the DPX-1300 power off until the

condensation disappears.

Set correctly.

Set [Lens Adjustment Lock] to off.

Press the MENU button to display the menu

and select [Setup]

[Lens Adjustment

Lock].

The connection cables are not correctly

attached to the connectors.

Correctly connect the cables to the

appropriate connectors.

The DPX-1300 does not

turn on.

The power cable is not plugged in.

You attempted to turn on The DPX-1300

immediately after turning it off.

The filter cover is not correctly attached.

The lamp cover is not correctly attached.

Wait for approximately two minutes.

<MEMO>

•

To protect the lamp, you cannot turn on

power for two minutes after you turn it off.

Plug the power cable in firmly.

Correctly attach the filter cover.

Correctly attach the lamp cover.

No picture. The lens cover has not been removed.

The DPX-1300 is not correctly connected

to the other components.

The input signal has not been correctly

selected.

The picture is turned off.

The computer is not set to display on the

external monitor.

Remove the lens cover.

Check the connections.

Select the correct input signal with the

INPUT button.

Press the AUTO button on the remote

control.

Use the menu to adjust the signal setting

to suit the input setting.

[Initial]

Press the HIDE button again to cancel the

HIDE function.

Set the computer to display on the external

monitor. (Refer to the computer operating

instructions.)

Press the FOCUS button, and adjust the

focus.

Adjust the projection angle and direction,

and the height of the DPX-1300.

Picture is blurred. The lens is not correctly focused.

The screen and the DPX-1300 are not

facing each other directly.

When a component is

digitally connected to

the HDMI or DVI

terminal, white noise or

a black image appears.

HDCP (High-bandwidth Digital Content

Protection) testing failed.

Press the Auto button on the remote

control or unplug the digital connection

cable, and then insert the cable again.

16_DPX-1300_E.p65 9/20/05, 4:02 PM60

Reference

English

Cause RemedyProblem

FAN warning indicator

lights up.

TEMP warning indicator

lights up.

COVER warning

indicator lights up.

LAMP warning

indicator lights up or

blinks.

The fan is broken.

The temperature inside the DPX-1300 is

extremely high.

The filter cover is not correctly attached.

The lamp cover is not correctly attached.

Lamp running time has exceeded 2000

hours.

The lamp has burned out.

Contact the store where the DPX-1300 was

purchased.

Check that the ventilation slots are not

covered.

Tightly attach the filter cover.

Tightly attach the lamp cover.

Replace the lamp with a new one.

• This unit uses a DMD

chip for the picture display. Their highly accurate technology makes it possible to keep more than 99.99%

of effective pixels, however, unexpectedly it can produce less than 0.01% of ineffective pixels. In such a case, missing or flashing

of a few pixels can be found on the screen. These are characteristics of DMD

, not mechanical problems.

Remote control does

not work correctly.

The batteries are exhausted.

The remote control sensor is not set

correctly.

There is a fluorescent lamp near the

remote control sensor being used.

The remote control code switch is

incorrectly set.

Replace both batteries with new ones.

Set correctly.

Press the MENU button to display the menu

and select [Setup]

[Remote Control

Sensor].

Turn off the remote control sensor near the

fluorecent lamp, and use the other remote

sensor.

Set the remote control code switch to the

same ID number as the setting on the

“REMOTE CONTROL ID” in the setting menu.

Troubleshooting

16_DPX-1300_E.p65 9/20/05, 4:02 PM61

Message display

Message Condition

No Signal

Memory 1—6 Now Processing

The lamps has reached its recommended

replacement time. Please replace with a new

one.

Invalid Operation

Lens Adjustment is locked.

INPUT A (Component) (Example)

Auto Sync...

Out Of Range

Unknown Format

Press again to enter standby.

The memory setting number is displayed for two seconds.

This message is displayed when the power switch is turned on if the lamp running time

exceeds 2000 hours. Press the ESCAPE button to remove the message.

This message will be displayed for two seconds if you press the V. POS, ZOOM, or FOCUS

button when [Lens Adjustment Lock] is set to [On].

Appears in the menu operation guide when you press an invalid button during menu

operation. This message will be displayed for two seconds.

The unit is not receiving or detecting any signal at the selected input jack. This message is

displayed together with the name of the input source selected with the INPUT button.

The input name selected by the INPUT button is displayed. It will turn off 2 seconds after

the signal has been input.

The unit is setting itself to the most appropriate configuration for the RGB signal currently

being received.

The unit is not able to decode the PC or HDMI signal currently being input.

The unit is not able to decode the video signal currently being input.

Press the STANDBY/ON button once more to place the unit in standby mode.

The color temp is fixed Appears in the menu operation guide when you try to change the settings for the color

temperature in the color temperature fixed mode.

Please wait

Appears in the menu screen when the unit requres few seconds for swiching process to the

selected menu item.

16_DPX-1300_E.p65 9/20/05, 4:02 PM62

Reference

English

LED indicator meanings

(*) This LED is also present on the front panel of the main unit.

LED indicator State

Unlit

Lit red

Blinking green

Meaning

Lit green

Blinking red

Blinking red / blinking

red rapidly

Unlit

Lit red

Unlit

Lit red

Unlit

Lit red

Unlit

Lit red

Blinking red

STANDBY/ON (*)

LAMP

COVER

TEMP

FAN

Electrical fault.

Standby

Preparing for operation.

Operating

Cooling the lamp.

Blinking red: Error in the LAMP/COVER/TEMP system

Blinking red rapidly: Error in the FAN system

Normal

The lamp has burned out.

Normal

The lamp cover or the filter cover is not attached correctly.

Normal

The temperature of the lamp or the interior of the case is abnormally high.

Normal

The cooling fan has broken.

The lamp running time has exceeded 2000 hours.

16_DPX-1300_E.p65 9/20/05, 4:02 PM63

Specifications

Usable temperature range

Usable humidity range

Power supply

Power consumption

Power consumption in standby mode

Noise level

Dimension

Weight

5 °C – 35 °C

30 % – 85 %(There should be no condensation)

AC100 – 120 V/220 – 240 V, 50/60 Hz

395 W

0.1 W – 0.2 W

30 dB(Standard mode), 28 dB(When Lamp Power Mode is set to 80)

495(W) x 192.6(H) x 465.4(D) mm

14.0 kg

• General

Wireless remote

Wired remote

1 in front, 1 at rear

1 input jack, 1 output jack

Remote

Trigger

RS-232C (D-sub 9 pins)

+12 V/Max 200 mA when the power is on

• Controls

• Input

HDMI

Digital RGB/component signal

Projection mode

Lens

Lamp

Screen size

Brightness

Contrast

DLP

(DMD

) type, 1280 X 720 pixels, 0.8 inch

f=24.3 – 38.9 mm F=2.7 – 5.0, Electronic zoom(x 1.6), Electronic focus, Electronic lens shift

270 W SHP lamp

60–200 inch (16:9)

800 – 400 ANSI lm (depends on Iris Setting)

2500:1 to 5000:1 (depends on Iris Setting)

• Optical

Color system

VIDEO Composite signal 1Vp-p/75 Ω, Negative sync

S-Video signal

Component signal

RGB signal

S VIDEO

D4 VIDEO

INPUT A/INPUT B

Y:1Vp-p/75 Ω, Negative sync

C:0.286 or 0.3Vp-p/75 Ω

Y with sync:1Vp-p/75 Ω, Negative sync

(480i, 576i, 480p, 576p)

Y with sync:1Vp-p/75 Ω, 3 values sync

(1035i, 1080i, 720p)

PB/CB, PR/CR:0.7Vp-p/75 Ω

Y with sync:1Vp-p/75 Ω, Negative sync (480i, 576i, 480p, 576p)

Y with sync:1Vp-p/75 Ω, 3 values sync (1035i, 1080i, 720p)

PB/CB, PR/CR:0.7Vp-p/75 Ω

G with sync:1Vp-p/75 Ω, Negative sync

(480i, 576i, 480p, 576p)

G with sync:1Vp-p/75 Ω, 3 values sync

(1035i, 1080i, 720p)

G:0.7Vp-p/75 Ω

(When using HD/VD or SYNC)

B, R:0.7Vp-p/75 Ω

HD, VD:1–5Vp-p/2.2kΩ, positive and negative sync

SYNC:2Vp-p/2.2kΩ, Negative sync (with video signals) (480i, 576i)

SYNC:0.6–5Vp-p/2.2kΩ, Negative sync (without video signals)

(480i, 576i, 480p, 576p)

NTSC, PAL, SECAM, NTSC4.43, PAL-M, PAL-N, PAL60

DVI Digital RGB signal

16_DPX-1300_E.p65 9/20/05, 4:02 PM64

Reference

English

Specifications are subject to change without notice.

• This unit may interfere with reception if placed in close proximity to a radio or television receiver. Follow the instructions in this

manual to install the unit correctly.

STANDBY

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUT

DIGITAL CINEMA PROJECTOR DPX-1000

ASPECT

HDMIDVI

G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC

OUT IN

REMOTE

TRIGGER OUT

S VIDEO VIDEO

INPUT B

RGB/YP

BPR/YCBCR

RS-232C

D4 VIDEO

465.4

18"-5/16

124.6

4"-7/8

119.1

4"-3/5

124

4"-7/8

297.4

11"-3/4

132.1

5"-3/16

495

19"-1/2

360

14"-3/16

192.6

7"-9/16

237.5

9"-3/8

3/8

(257.5

10"-1/8)

Dimensional drawing

16_DPX-1300_E.p65 9/20/05, 4:02 PM65

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Japan WF80490

DPX-1300

DIGITAL CINEMA PROJECTOR

PROJECTEUR CINEMA NUMERIQUE

DPX-1300

10_DPX-1300-Cover1-4_U.p65 9/22/05, 4:28 PM1

Yamaha DPX-1300 Handleiding

Merk: Yamaha

Model: DPX-1300

Categorie: Dataprojectoren

Type: Handleiding

Deze handleiding is ook geschikt voor

Projector DPX-1300

Download PDF

rapport

in andere talen

English: Yamaha DPX-1300 User manual
italiano: Yamaha DPX-1300 Manuale utente
русский: Yamaha DPX-1300 Руководство пользователя
français: Yamaha DPX-1300 Manuel utilisateur
español: Yamaha DPX-1300 Manual de usuario
Deutsch: Yamaha DPX-1300 Benutzerhandbuch
português: Yamaha DPX-1300 Manual do usuário
dansk: Yamaha DPX-1300 Brugermanual
suomi: Yamaha DPX-1300 Ohjekirja
čeština: Yamaha DPX-1300 Uživatelský manuál
svenska: Yamaha DPX-1300 Användarmanual
Türkçe: Yamaha DPX-1300 Kullanım kılavuzu
polski: Yamaha DPX-1300 Instrukcja obsługi
română: Yamaha DPX-1300 Manual de utilizare

Yamaha DPX-1300 Handleiding

Deze handleiding is ook geschikt voor

Yamaha DPX-1300 Handleiding

in andere talen

Gerelateerde artikelen

Andere documenten