Zebra CRD-TC55-VCD1-01 Installatie gids

Type
Installatie gids
CRD-TC55-VCD1-01
VEHICLE CRADLE
INSTALLATION GUIDE
Installation
Install the vehicle mount on a surface of your vehicle that is flat
and free of dirt and oil. Clean the mounting surface with a glass
cleaner and a clean cotton cloth. Install the vehicle mount on the
windshield or other flat car surface using the supplied disc.
The TC55 can detect when it is inserted into the cradle. Use the
Dock settings to configure the TC55 when in the cradle. See the
TC55 User Guide for more information.
Assembly
1. Remove all parts from plastic bags.
2. Insert the arm ball through the nut and into the socket on the
holder.
3. Secure nut but do not tighten at this time.
4. Remove protective plastic from suction cup.
Windshield Installation
5. Fix the suction cup mount to the selected area with the
suction lever facing up.
6. Flip the lever down to create a vacuum between the suction
cup and the disc.
7. Make sure that the suction bond is strong enough before
installing the TC55.
Dash Mount Installation
1. Install the disc using the instructions provided with the disc.
2. Remove protective plastic from top of disc.
3. Fix the suction cup mount to the disc with the suction lever
facing you.
4. Flip the lever down to create a vacuum between the suction
cup and the disc.
5. Make sure that the suction bond is strong enough before
installing the TC55.
Install the TC55
1. Place the TC55 top first into the cradle and lift.
2. Rotate into the cradle and sit into the bottom of the cradle.
3. Position the TC55 for best viewing.
4. Tighten the nut to lock the cradle in place.
Connect Power
1. If required, connect the micro USB connector of the auto
charge cable (VCA400-01R) to the input power port of the
vehicle cradle.
2. Use the cable retention feature to secure the cable.
3. Connect the other end to the cigarette lighter socket.
The TC55 LED flashes green indicating the TC55 is
charging.
4. Route the auto charger cable so that it does not interfere with
driving.
Remove the TC55
Lift the TC55 up and then remove from the bottom of the cradle.
Regulatory Information
This guide applies to the following Model Number: CRD-TC55-
VCD1.
All Zebra devices are designed to be compliant with rules and
regulations in locations they are sold and will be labeled as
required.
Local language translations are available at the following
website: http://www.zebra.com/support.
Any changes or modifications to Zebra equipment, not expressly
approved by Zebra could void the user’s authority to operate the
equipment.
For use only with Zebra approved and UL Listed mobile
computers.
Declared maximum operating temperature 50ºC.
Vehicle Installation
IMPORTANT: Before installing or using, check state and local
laws regarding windshield mounting and use of equipment.
For Safe installation
Do not put your phone in a location that obstructs the drivers
vision or interferes with the operation of the Vehicle
Do not cover an airbag.
RF signals may affect improperly installed or inadequately
shielded electronic systems in motor vehicles (including safety
systems). Check with the manufacturer or its representative
regarding your vehicle. You should also consult the
manufacturer of any equipment that has been added to your
vehicle.
An air bag inflates with great force. DO NOT place objects,
including either installed or portable wireless equipment, in the
area over the air bag or in the air bag deployment area. If in-
vehicle wireless equipment is improperly installed and the air
bag inflates, serious injury could result.
Position your device within easy reach. Be able to access your
device without removing your eyes from the road.
Note: Connection to an alert device that will cause a vehicle
horn to sound or lights to flash, on receipt of a call on public
roads, is not permitted.
NOTE The cradle accommodates the TC55 with or without
the protective boot and with the 2,940 mAh or 4,410
mAh battery.
Do not leave the TC55 in direct sunlight for a long
period of time as it may cause the TC55 to exceed
proper operating temperature.
1
2
Auto Charge Cable
Input Power Port
Cable
Retention
Zebra reserves the right to make changes to any product to
improve reliability, function, or design. Zebra does not assume
any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application
described herein. No license is granted, either expressly or by
implication, estoppel, or otherwise under any patent right or
patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which
Zebra products might be used. An implied license exists only for
equipment, circuits, and subsystems contained in Zebra
products.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp.
The Symbol logo is a registered trademark of Symbol Technologies, Inc., a
Zebra Technologies company.
© 2015 Symbol Technologies LLC.
MN000088A04 Revision A — October 2015
Safety on the Road
Do not take notes or use the device while driving. Jotting down a
“to do” list or flipping through your address book takes attention
away from your primary responsibility, driving safely.
When driving a car, driving is your first responsibility - Give full
attention to driving. Check the laws and regulations on the use
of wireless devices in the areas where you drive. Always obey
them.
When using a wireless device behind the wheel of a car, practice
good common sense and remember the following tips:
1. Get to know your wireless device and any features such as
speed dial and redial. If available, these features help you to
place your call without taking your attention off the road.
2. When available, use a hands free device.
3. Let the person you are speaking with know you are driving; if
necessary, suspend the call in heavy traffic or hazardous
weather conditions. Rain, sleet, snow, ice, and even heavy
traffic can be hazardous.
4. Dial sensibly and assess the traffic; if possible, place calls
when you are not moving or before pulling into traffic. Try to
plan calls when your car will be stationary. If you need to
make a call while moving, dial only a few numbers, check the
road and your mirrors, then continue.
5. Do not engage in stressful or emotional conversations that
may be distracting. Make people you are talking with aware
you are driving and suspend conversations that have the
potential to divert your attention from the road.
6. Use your wireless phone to call for help. Dial the Emergency
services, (9-1-1 in the US, and 1-1-2 in Europe) or other local
emergency number in the case of fire, traffic accident or
medical emergencies. Remember, it is a free call on your
wireless phone! The call can be made regardless of any
security codes and depending on a network, with or without
a SIM card inserted.
7. Use your wireless phone to help others in emergencies. If
you see an auto accident, crime in progress or other serious
emergency where lives are in danger, call the Emergency
Services, (9-1-1 in the US, and 1-1-2 in Europe) or other
local emergency number, as you would want others to do for
you.
8. Call roadside assistance or a special non-emergency
wireless assistance number when necessary. If you see a
broken-down vehicle posing no serious hazard, a broken
traffic signal, a minor traffic accident where no one appears
injured, or a vehicle you know to be stolen, call roadside
assistance or other special non-emergency wireless number.
“The wireless industry reminds you to use your device / phone
safely when driving”.
Radio Frequency Interference Require-
ments - FCC
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for
help.
Radio Frequency Interference
Requirements- Canada
CAN ICES-3 (B)/NMB-3(B)
Marking and European Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this device is in compliance with all
the applicable Directives, 2004/108/EC, 2006/95/EC and 2011/
65/EU. A Declaration of Conformity may be obtained from http://
www.zebra.com/doc.
Japan (VCCI) - Voluntary Control Council for
Interference
Class B ITE
この装置は、情報処理装置等電波障害自主規制協議会 (VCC
I)の基準に基づくクラス B 情報技術装置です。この装置は、
家庭環境で使用することを目的としていますが、この装置が
ジオやテレビジョン受信機に近接して使用されると、受信障
を引き起こすことがあります。 取扱説明書に従って正しい取
り扱いをして下さい。
China
English: For EU Customers: All products at the end of their life must be
returned to Zebra for recycling. For information on how to return product,
please go to: http://www.zebra.com/weee.
Français: Clients de l'Union Européenne : Tous les produits en fin de cycle
de vie doivent être retournés à Zebra pour recyclage. Pour de plus amples
informations sur le retour de produits, consultez : http://www.zebra.com/
weee.
Español: Para clientes en la Unión Europea: todos los productos deberán
entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si
desea más información sobre cómo devolver un producto, visite: http://
www.zebra.com/weee.
Български: За клиенти от ЕС: След края на полезния им живот всички
продукти трябва да се връщат на Zebra за рециклиране. За
информация относно връщането на продукти, моля отидете на адрес:
http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende
ihrer Lebensdauer zum Recycling an Zebra zurückgesandt werden.
Informationen zur Rücksendung von Produkten finden Sie unter http://
www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del
rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne
il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il
seguente sito Web: http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem
ser devolvidos à Zebra para reciclagem. Para obter informações sobre
como devolver o produto, visite:
http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde
van hun levensduur naar Zebra te worden teruggezonden voor recycling.
Raadpleeg http://www.zebra.com/weee voor meer informatie over het
terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z
eksploatacji naleźy zwrócić do firmy Zebra w celu ich utylizacji. Informacje
na temat zwrotu produktów znajdują się na stronie internetowej http://
www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení
jejich životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu
vrácení produktu najdete na webové stránce: http://www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada
taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi:
http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra
vállalathoz kell eljuttatni újrahasznosítás céljából. A termék
visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a
http://www.zebra.com/weee weboldalra.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd
måste returneras till Zebra för återvinning. Information om hur du returnerar
produkten finns på
http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on
palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä.
Lisätietoja tuotteen palauttamisesta on osoitteessa
http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til
recirkulering, når de er udtjent. Læs oplysningerne om returnering af
produkter på: http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της
διάρκειας ζωής τους, πρέπει να επιστρέφονται στην Zebra για
ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή
ενός προϊόντος, επισκεφθείτε τη διεύθυνση
http://www.zebra.com/weee στο ∆ιαδίκτυο.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta'
l-użu tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar
tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: http://
www.zebra.com/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor
de funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii
despre returnarea produsului, accesaţi: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe
vrniti podjetju Zebra za reciklažo. Za informacije o vračilu izdelka obiščite:
http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po
uplynutí doby ich životnosti vrátené spoločnosti Zebra na recykláciu.
Bližšie informácie o vrátení výrobkov nájdete na:
http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui,
turi būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip
grąžinti gaminį, rasite: http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir
jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par
produktu nogādāšanu Zebra, lūdzu, skatiet:
http://www.zebra.com/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri
dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği
hakkında bilgi için lütfen şu adresi ziyaret edin:
http://www.zebra.com/weee.
TURKISH WEEE Statement of Compliance
EEE Yönetmeliğine Uygundur
Warranty
For the complete Zebra hardware product warranty statement,
go to: http://www.zebra.com/warranty.
Service Information
If you have a problem using the equipment, contact your
facility’s Technical or Systems Support. If there is a problem with
the equipment, they will contact the Zebra Global Customer
Support at: http://www.zebra.com/support.
For the latest version of this guide go to:
http://www.zebra.com/support.
CMM Disclosure
本表格依据SJ/T 11364 的规定编制。
O: 示该害物 GB/T
26572 规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量超
GB/T 26572 规定的限量要求。( 企业可在此处,根据实
际情况对上表中打 “×” 的技术原因进行进一步说明。
This table was created to comply with China RoHS
requirements.
Waste Electrical and Electronic
Equipment (WEEE)
部件名称
(Parts)
有害物质
(Pb)
(Hg)
(Cd)
六价
(Cr(VI))
多溴联
(PBB)
多溴二
苯醚
(PBDE)
金属部件
(Metal Parts)
OOO O O O
电路模块
(Circuit Modules)
XOO O O O
电缆及电缆组件
(Cables and Cable
Assemblies)
OOO O O O
塑料和聚合物部件
(Plastic and
Polymeric Parts)
OOO O O O
光学和光学组件
(Optics and Optical
Components)
OOO O O O
电池
(Batteries)
OOO O O O
  • Page 1 1
  • Page 2 2

Zebra CRD-TC55-VCD1-01 Installatie gids

Type
Installatie gids