User Guide
Zebra reserves the right to make changes to any product to improve reliability, function,
or design.
Zebra does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under
any patent right or patent, covering or relating to any combination, system, apparatus,
machine, material, method, or process in which Zebra products might be used. An
implied license exists only for equipment, circuits, and subsystems contained in Zebra
products.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Zebra Technologies Corporation
Lincolnshire, IL, USA
http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol
logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies
company.
© 2015 Symbol Technologies, Inc.
72-113888-03 Revision A — April 2015
1 2 3
MC7XFPR-01R
MC7XFPSCR-01R
Introduction
The MC7XFPR-01R Biometric Reader contains only a finger print reader. The
MC7XFPSCR-01R Biometric Reader contains a finger print reader, a contact
smart card reader and a contactless smart card reader. The Biometric Reader
snaps onto the bottom of the MC70/75 mobile computer. This guide describes
how to install and use the reader.
The LED indicates the power and status of the smart card.
Installation
1. Align the reader with the bottom of the MC70/75 and push up until the locking
tabs snap into place.
2. Pull on the reader to ensure it is securely connected to the MC70/75.
Removal
To remove the reader from the MC70/75, push in the bottom of the two locking
tabs and pull the reader from the MC70/75.
Smart Card Reading
1. Launch a smart-card reader enabled application.
2. Open the Smart Card slot cover.
3. Insert the Smart Card into the slot, orienting the Smart Card with the contacts
facing down and toward the reader.
4. To remove the Smart Card, pull the card out of the slot.
5. Close Smart Card slot cover.
Contact-less Smart Card Reading
1. Launch a contact-less smart card reader enabled application.
2. Place the back of the reader near the item to read.
Finger Print Reading
1. Launch a finger print enabled application.
2. Present the reader to the user. The user presses their finger on the finger print
reader area.
LED
Color
Description
Green Power is applied and the reader is ready.
Blinking
Yellow
Reader is transferring data.
Solid
Yellow
Error. Reader is receiving improper response from a
card.
Smart Card Slot Cover
Finger Print Reader
LED
5 6 74
3. Ensure that the application indicates that a good read was performed.
Charging the MC70/75
You can charge the MC70/75 while the reader is installed. Place the MC70/75 with
the reader into a cradle to charge the MC70/75.
When the reader is placed in a cradle or cable, the reader is inactive and the
pass-through is enabled for charging.
Maintenance
There are no serviceable part in the reader. Do not tamper with the device.
Regulatory Information
This guide applies to the following Model Numbers: MC7XFPR-01R, MC7XFPSCR-
01R.
All Zebra devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Local language translations are available at the following website:
http://www.zebra.com/support
Any changes or modifications to Zebra equipment, not expressly approved by Zebra
could void the user’s authority to operate the equipment.
For use only with Zebra approved and UL Listed mobile computers. Zebra approved
and UL Listed accessories and/or Zebra approved and UL Listed/Recognized battery
packs.
Declared maximum operating temperature 50ºC.
Power Supply
The power supply shall be Listed to UL/CSA 60950-1; and certified to IEC60950-1 and
EN60950-1 with SELV outputs. Use of alternative power supply will invalidate any
approval given to this device and may be dangerous.
Wireless Device Country Approvals
Regulatory markings, subject to certification, are applied to the device signifying the
radio(s) is/are approved for use in the following countries: United States, Canada.
Please refer to the Zebra Declaration of Conformity (DoC) for details of other country
markings. This is available at http://www.zebra.com/doc/.
The use of RFID Devices have varying restrictions of use; please refer to the Zebra
Declaration of Conformity (DoC) for details.
Health and Safety Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the
recommendations below. Consult with your local Health & Safety Manager to ensure
that you are adhering to your company’s safety programs to prevent employee injury.
•
Reduce or eliminate repetitive motion
•
Maintain a natural position
•
Reduce or eliminate excessive force
•
Keep objects that are used frequently within easy reach
•
Perform tasks at correct heights
•
Reduce or eliminate vibration
•
Reduce or eliminate direct pressure
•
Provide adjustable workstations
•
Provide adequate clearance
•
Provide a suitable working environment
•
Improve work procedures.
Please observe all warning notices with regard to the usage of wireless devices.
Potentially Hazardous Atmospheres – Vehicles Use
You are reminded of the need to observe restrictions on the use of radio devices in fuel
depots, chemical plants etc. and areas where the air contains chemicals or particles
(such as grain, dust, or metal powders) and any other area where you would normally
be advised to turn off your vehicle engine.
Safety in Aircraft
Switch off your wireless device whenever you are instructed to do so by airport or airline
staff. If your device offers a ‘flight mode’ or similar feature, consult airline staff as to its
use in flight.
Safety in Hospitals
Wireless devices transmit radio frequency energy and may affect medical electrical
equipment.
Wireless devices should be switched off wherever you are requested to do so in
hospitals, clinics or healthcare facilities. These requests are designed to prevent
possible interference with sensitive medical equipment.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be
maintained between a handheld wireless device and a pacemaker to avoid potential
interference with the pacemaker. These recommendations are consistent with
independent research and recommendations by Wireless Technology Research.
Persons with Pacemakers:
•
Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker
when turned ON.
•
Should not carry the device in a breast pocket.
•
Should use the ear furthest from the pacemaker to minimise the potential for
interference.
•
If you have any reason to suspect that interference is taking place, turn OFF your
device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to determine if
the operation of your wireless product may interfere with the medical device.
Safety Information
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering human
exposure to electromagnetic fields from radio devices.
US and Canada
Co-located statement
To comply with FCC RF exposure compliance requirement, the antenna used for this
transmitter must not be co-located or operating in conjunction with any other transmitter/
antenna except those already approved in this filling.
Handheld Devices
This device was tested for typical body-worn operation. Use only Zebra tested and
approved belt-clips, holsters, and similar accessories to ensure FCC Compliance. The
use of third-party belt-clips, holsters, and similar accessories may not comply with FCC
RF exposure compliance requirements, and should be avoided.
Batteries
Battery Information
Zebra rechargeable battery packs are designed and constructed to the highest
standards within the industry.
However, there are limitations to how long a battery can operate or be stored before
needing replacement. Many factors affect the actual life cycle of a battery pack, such as
heat, cold, harsh environmental conditions and severe drops.
When batteries are stored over six (6) months, some irreversible deterioration in overall
battery quality may occur. Store batteries at half of full charge in a dry, cool place,
removed from the equipment to prevent loss of capacity, rusting of metallic parts and
electrolyte leakage. When storing batteries for one year or longer, the charge level
should be verified at least once a year and charged to half of full charge.
Replace the battery when a significant loss of run time is detected.
Standard warranty period for all Zebra batteries is one year, regardless if the battery
was purchased separately or included as part of the mobile computer. For more
information on Zebra batteries, please visit: http://www.zebra.com/batterybasics.
Battery Safety Guidelines
•
The area in which the units are charged should be clear of debris and combustible
materials or chemicals. Particular care should be taken where the device is charged
in a non commercial environment.
•
Follow battery usage, storage, and charging guidelines found in the user's guide.
•
Improper battery use may result in a fire, explosion, or other hazard.
•
To charge the mobile device battery, the battery and charger temperatures must be
between +32°F and +104°F (0°C and +40°C).
•
Do not use incompatible batteries and chargers. Use of an incompatible battery or
charger may present a risk of fire, explosion, leakage, or other hazard. If you have
any questions about the compatibility of a battery or a charger, contact Zebra
support.
•
Do not disassemble or open, crush, bend or deform, puncture, or shred.
•
Severe impact from dropping any battery-operated device on a hard surface could
cause the battery to overheat.
•
Do not short circuit a battery or allow metallic or conductive objects to contact the
battery terminals.
•
Do not modify or remanufacture, attempt to insert foreign objects into the battery,
immerse or expose to water or other liquids, or expose to fire, explosion, or other
hazard.
•
Do not leave or store the equipment in or near areas that might get very hot, such as
in a parked vehicle or near a radiator or other heat source. Do not place battery into
a microwave oven or dryer.
•
Battery usage by children should be supervised.
•
Please follow local regulations to promptly dispose of used re-chargeable batteries.
•
Do not dispose of batteries in fire.
•
Seek medical advice immediately if a battery has been swallowed.
•
In the event of a battery leak, do not allow the liquid to come in contact with the skin
or eyes. If contact has been made, wash the affected area with large amounts of
water and seek medical advice.
•
If you suspect damage to your equipment or battery, contact Zebra support to
arrange for inspection.
Radio Frequency Interference Requirements-FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio Transmitters
This device complies with RSS 210 of Industry & Science Canada. Operation is subject
to the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Label Marking: The Term “IC:” before the radio certification only signifies that Industry
Canada technical specifications were met.
Marking and European Economic Area (EEA)
Statement of Compliance
Zebra, hereby declares that this device is in compliance with all the applicable
Directives, 1999/5/EC, 2004/108/EC, 2006/95/EC and 2011/65/EU. A Declaration of
Conformity may be obtained from http://www.zebra.com/doc.
English: For EU Customers: All products at the end of their life must be returned to Zebra
for recycling. For information on how to return product, please go to:
http://www.zebra.com/weee.
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie
doivent être retournés à Zebra pour recyclage. Pour de plus amples informations sur le
retour de produits, consultez : http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a
Zebra al final de su ciclo de vida para que sean reciclados. Si desea más información
sobre cómo devolver un producto, visite: http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer
Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo
di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni
sulle modalità di restituzione, visitare il seguente sito Web: http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos
à Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite:
http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun
levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg http://
www.zebra.com/weee voor meer informatie over het terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y
zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów
znajduj¹ siê na stronie internetowej http://www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti
vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na
webové stránce: http://www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise
eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage
palun aadressi: http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell
eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos
tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju
Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite: http://www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras
till Zebra för återvinning. Information om hur du returnerar produkten finns på http://
www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen
palauttamisesta on osoitteessa http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er
udtjent. Læs oplysningerne om returnering af produkter på: http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους,
πρέπει να
επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες
σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση http://
www.zebra.com/weee στο ∆ιαδίκτυο.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu
tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif
għandek tirritorna l-prod.5ott, jekk jogħġbok żur: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju
Zebra za reciklažo. Za informacije o vračilu izdelka obiščite: http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich
životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov
nájdete na: http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti
grąžinti utilizuoti
į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite:
http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ
Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra,
lūdzu, skatiet: http://www.zebra.com/weee.
NOTE If you are going to replace the MC70/75 battery, remove the reader
from the MC70/75 before replacing the battery.
CAUTION Only use Zebra approved and UL Listed accessories, battery
packs and battery chargers.
Do NOT attempt to charge damp/wet mobile computers or
batteries. All components must be dry before connecting to an
external power source.
Operation of the device without regulatory approval is illegal.
Ergonomic Recommendations
Warnings for Use of Wireless Devices
RF Exposure Guidelines
CAUTION Risk of explosion if battery is replaced by an incorrect type.
Dispose of batteries according to instructions.
Waste Electrical and Electronic Equipment
(WEEE)
-
1
-
2
in andere talen
- English: Zebra MC70/75 User guide
Gerelateerde artikelen
-
Zebra MC3000 de handleiding
-
-
-
-
-
-
-
-
-