INSTALLATION ● OPERATION
OWNER’S MANUAL
Incogneeto™Buffet Warming System
Models B651-U, B652-U
Part Numbers 658900, 659000
CookTek Induction Systems, LLC
Toll Free: +1 (888) COOKTEK
Toll Free Fax: +1 (888) COOKFAX
Phone: +1 (312) 563-9600
Fax: +1 (312) 432-6220
www.cooktek.com
CookTek Induction Systems, LLC
Toll Free: +1 (888) COOKTEK
Toll Free Fax: +1 (888) COOKFAX
Phone: +1 (312) 563-9600
Fax: +1 (312) 432-6220
www.cooktek.com
Manual Incogneeto 12040_A USINTL
103456
22
Antes de Começar:
Por favor, certifique-se de que este cabo de energia está ligado firmemente à sua
unidade CookTek ANTES de ligar a unidade à tomada de energia e antes de
tentar funcionar com ela.
●Não toque na placa de cerâmica (no cimo do Cooktop) imediatamente depois
da sua utilização. O calor emitido pelo tabuleiro será transferido para a placa
de cerâmica, fazendo com que esta fique quente ao toque.
●A assistência técnica deste produto só pode ser realizada por um agente de
assistência técnica autorizado ou por pessoal da CookTek. Não tente abrir a
unidade nem efectuar assistência técnica de qualquer tipo. Para informações
referentes à assistência técnica, por favor entre em contacto com a CookTek
pelo telefone 1-312-563-9600.
●O aparelho deve estar ligado à terra. Ligue apenas a uma tomada
correctamente ligada à terra. Antes de funcionar com o aparelho, leia as
instruções relativas à ligação à terra e os Requisitos para Instalação Eléctrica
na Página 3 deste folheto. Não utilize um cabo de extensão.
Antes de utilizar el anafe (cooktop), realice lo siguiente:
●Retire todo el material de embalaje.
●Coloque la unidad sobre una superficie seca, plana, dura, estable y no
inflamable.
●Mantenga la unidad alejada de otras fuentes de calor y deje un margen de al
menos 5 cm para que el aire circule por los lados y las partes anterior y
posterior de la unidad.
Por su seguridad, nunca corte, quite ni inutilice la conexión eléctrica (tierra) del
enchufe. No utilice nunca el anafe con un enchufe adaptador ni un cable
prolongador.
ADVERTENCIA: Se puede producir un choque eléctrico por un enchufe
conectado a tierra de manera incorrecta. Si tiene alguna duda relacionada
con las instrucciones de conexión a tierra, póngase en contacto con un
electricista cualificado.
Antes de comenzar:
Asegúrese de que el cable eléctrico está unido firmemente a la unidad CookTek
ANTES de conectar la unidad a la electricidad y antes de intentar utilizarla.
●No toque la placa cerámica (situada en la parte superior del anafe)
inmediatamente después de utilizarla. El calor de la cazuela se transferirá a la
placa cerámica y hará que ésta se caliente.
●La revisión de este producto únicamente puede realizarla un operario de
mantenimiento autorizado o el personal de CookTek. No intente abrir la unidad
ni realizar ninguna labor de mantenimiento. Para obtener información sobre el
mantenimiento, póngase en contacto con CookTek llamando al 1-312-563-
9600.
●Este aparato se debe conectar a tierra. Enchúfelo únicamente a una toma
conectada a tierra de manera adecuada. Antes de utilizarlo, lea las
instrucciones de conexión a tierra y los “Requisitos de la instalación eléctrica”
de la página 3 de este folleto. No utilice cables prolongadores.
SPANISH
Manual Incogneeto 12040_A USINTL
21 2
Przed rozpoczęciem używania urządzenia Cooktop, należy wykonać poniższe
czynności:
●Usunąć wszystkie elementy opakowania.
●Ustawić urządzenie na suchej, poziomej, twardej, stabilnej i niepalnej
powierzchni.
●Ustawić urządzenie z dala od innych źródeł ciepła i zapewnić wokół urządzenia
wolną przestrzeń, co najmniej 0,5 cm, aby umożliwić obieg powietrzaDla
bezpieczeństwa użytkownika nie wolno nigdy przecinać, wyjmować ani
wyłączać połączenia elektrycznego (uziemienia) z wtyczki. Stosując urządzenie
Cooktop nie wolno używać złącza pośredniego ani przedłużacza.
OSTRZEŻENIE: Niewłaściwe uziemienie wtyczki może spowodować
porażenie prądem elektrycznym. W przypadku wątpliwości dotyczących
instrukcji uziemienia należy skontaktować się z wykwalifikowanym
elektrykiem.
Przed rozpoczęciem używania:
Należy sprawdzić, czy przewód zasilania jest pewnie przymocowany do modułu
CookTek PRZED podłączeniem urządzenia do gniazdka zasilania i przed
rozpoczęciem jego używania.
●Nie dotykać płyty ceramicznej (lub wierzchniej części urządzenia Cooktop)
bezpośrednio po zakończeniu jego używania. Wysoka temperatura patelni
może przenosić się na płytę ceramiczną, stwarzając możliwość oparzenia w
przypadku jej dotknięcia.
●Obsługa serwisowa tego produktu może być prowadzona jedynie przez
upoważnionego pracownika serwisu lub przez personel firmy CookTek. Nie
podejmować samodzielnej próby otwarcia urządzenia ani nie wykonywać
żadnych napraw. Aby uzyskać informacje dotyczące obsługi serwisowej, należy
skontaktować się z firmą CookTek pod numerem 1-312-563-9600.
●Niniejsze urządzenie wymaga uziemienia. Podłączać jedynie do właściwie
uziemionego gniazda. Przed użyciem należy przeczytać instrukcję dotyczącą
uziemienia oraz część „Wymogi instalacji elektrycznej” na stronie 3 niniejszej
ulotki. Nie używać przedłużacza.
Antes de funcionar com o seu Cooktop, faça o seguinte:
●Retire todo o material de embalagem.
●Coloque a unidade numa superfície seca, nivelada, rígida, estável e não
inflamável.
●Mantenha a unidade afastada de outras fontes de calor e deixe um espaço de
pelo menos 5 cm nos lados, frente e traseira da unidade, para circulação do ar.
Para sua segurança, nunca corte, retire nem desactive a ligação eléctrica (terra) da
ficha. Nunca utilize uma ficha adaptadora nem cabo de extensão com o Cooktop.
ADVERTÊNCIA: Uma ficha incorrectamente ligada à terra pode provocar
choque eléctrico. Se tiver alguma questão sobre estas instruções de ligação
à terra, por favor consulte um electricista qualificado.
PORTUGUESE
POLISH
Before operating your buffet, do the following:
●Remove all packing material and save for subsequent shipment or in case of
concealed shipping damage.
●Keep unit away from other heat sources and allow at least two (2) inches
clearance for air circulation at sides, front and rear of the unit. If either the air
intake or exhaust outlet is blocked, the internal temperature will rise, causing an
error code to occur.
Grounding Instructions:
The buffet must be properly grounded. In the event of an electrical short circuit,
grounding reduces the risk of electric shock by providing a safe path for the electric
current. The buffet has a power cord with a 3-prong grounding plug, which must be
used in a compatible and properly grounded outlet. It is the owner’s responsibility
to replace any 2-prong wall outlet with a properly grounded 3-prong wall receptacle.
For your safety, never cut, remove, or disable the electrical (ground) connection
from the plug. Never use an adapter plug or an extension cord with the buffet.
WARNING: Electric shock can result from an improperly grounded plug. Please
consult a qualified electrician if you have any questions about these grounding
instructions.
Before you begin:
Please make sure that this power cord is firmly attached to your CookTek unit
BEFORE plugging the unit into the power receptacle and before attempting
operation.
Every installation site has different electrical wiring. Because many different local
codes exist, it is the Owner and Installer’s responsibility to comply with those
codes. CookTek is not responsible for any consequential damages as a result of
failure to comply with installation requirements.
●Read all installation instructions carefully before starting installation.
●Remove buffet carefully from carton.
●Remove all loose packaging and accessories and save for subsequent
shipment or in case of concealed shipping damage.
●It is the responsibility of the installer to comply with all federal, state and local
codes.
●Any installation not matching the specifications discussed in this manual
automatically voids the product’s warranty.
tag must be positioned over.
PREPARING YOUR COOKTEK BUFFET UNIT FOR USE
ELECTRICAL INSTALLATION REQUIREMENTS
Manual Incogneeto 12040_A USINTL
3 20
Per la propria sicurezza, non tagliare, rimuovere o disattivare mai il collegamento
elettrico di terra dalla spina. Non utilizzare mai una spina adattatore o un cavo
elettrico di prolunga per collegare il piano cottura.
AVVERTENZA: una spina elettrica non correttamente collegata all'impianto di
terra può provocare scosse elettriche. Rivolgersi a un elettricista qualificato
in caso di domande su queste istruzioni di messa a terra.
Prima di iniziare:
Assicurarsi che questo cavo di alimentazione sia collegato saldamente all'unità
CookTek PRIMA di collegare l'unità alla presa elettrica e prima di metterla in
funzione.
●Non toccare la piastra di ceramica (o la superficie del piano cottura) subito dopo
l'uso. Il calore della pentola si trasferisce alla piastra di ceramica, rendendola
estremamente calda.●Questo prodotto può essere riparato esclusivamente da
un tecnico autorizzato o dal centro di assistenza CookTek. Non tentare di aprire
l'unità o di eseguire interventi di manutenzione di alcun tipo. Per informazioni
sull'assistenza, contattare la CookTek al numero 1-312-563-9600.
●Questo apparecchio deve essere collegato a terra. Collegarlo esclusivamente a
una presa elettrica dotata di messa a terra. Prima di mettere in funzione l'unità,
leggere le istruzioni di messa a terra e i Requisiti di installazione elettrica a
pagina 3 di questo opuscolo. Non utilizzare un cavo elettrico di prolunga.
Før du bruker komfyren, må du gjøre følgende:
●Fjern all emballasje.
●Plasser enheten på et tørt, jevnt, hardt, stabilt og brannsikkert underlag.
●Hold enheten unna andre varmekilder, og la det være minst 5 cm klaring for
luftventilasjon på sidene, foran og på baksiden av enheten.
For din egen sikkerhet må du ikke kutte, fjerne eller ødelegge den elektriske
(jordede) koplingen fra kontakten. Ikke bruk en adapterkontakt eller skjøteledning
for komfyren.
ADVARSEL: Elektrisk støt kan oppstå fra kontakt som ikke er korrekt jordet.
Ta kontakt med en kvalifisert elektriker dersom du har spørsmål om disse
jordingsinstruksene.
Før du begynner:
Kontroller at strømkabelen er satt helt inn i CookTek-enheten FØR du kopler
enheten til stikkontakten og før bruk.
●Den keramiske platen (eller overflaten på komfyren) må ikke berøres
umiddelbart etter bruk. Varme fra kjeler vil overføres til den keramiske platen og
gjøre den varm.
●Dette produktet kan bare repareres av en autorisert serviceagent eller av
CookTek-ansatte. Ikke prøv å åpne enheten eller utføre reparasjoner av noe
slag. For serviceinformasjon, kontakt CookTek på tlf. 1-312-563-9600.
●Dette produktet må jordes. Må kun koples til et korrekt jordet støpsel. Før bruk
bør du lese jordingsinstruksene og kravene til elektrisk installasjon på side 3 i
denne veiledningen. Ikke bruk skjøteledning.
NORWEGIAN
●Install the mounting tracks per the installation sheet provided with either the
single unit tracks or the rail kit as appropriate. Also see instructions at the end
of this manual.
●Insert the unit with the Antenna side sticker away from the customer. This is
the side of the unit that the Magneeto™II
●To install the unit on the tracks, hook one side of the
springs onto the track and then compress the other
side of the mounting springs and snap it into the track.
See assembly drawing.
Model Types
B651-U - 100-120VAC model
B652-U - 200-240VAC model
User Interface Buttons
Power button - Use this button to turn the unit on and off. A green LED
will indicate when the unit is on.
Lock button - Use this button to prevent users from adjusting settings.
Pressing this button three times will lock the unit. When the unit is
locked, the only button that will continue to work is the Power button.
To unlock the unit, press the Lock button three times. The red LED to the right
of the button will indicate when the unit is locked.
Up and Down Arrows - These buttons allow you to
quickly set the temperature.
Alphanumeric display - Displays holding temperature (Fahrenheit or Celsius) and
error code information.
MECHANICAL INSTALLATION
GENERAL INFORMATION
Manual Incogneeto 12040_A USINTL
19 4
● Dieses Produkt darf nur durch bevollmächtigte Wartungstechniker oder das
Fachpersonal von CookTek gewartet werden. Versuchen Sie nicht, das Gerät
zu öffnen und selbst zu warten. Nähere Informationen zur Wartung erhalten Sie
bei CookTek unter der Rufnummer 1-312-563-9600.
● Das Gerät muss geerdet werden. Der Stecker muss in eine ordnungsgemäß
geerdete Steckdose gesteckt werden. Vor dem Öffnen lesen Sie bitte die
Anweisungen zu Schutzkontakt/Erdung und die Anforderungen an die
elektrische Installation auf Seite 3 dieses Handbuchs. Verwenden Sie kein
Verlängerungskabel.
Πριν θέσετε το Cooktop σας σε λειτουργία, εκτελέστε τα ακόλουθα:
●Αφαιρέστε όλα τα υλικά συσκευασίας.
●Τοποθετήστε τη μονάδα σε μια στεγνή, επίπεδη, σκληρή, σταθερή και μη
εύφλεκτη επιφάνεια.
●Διατηρήστε τη μονάδα μακριά από άλλες πηγές θερμότητας και αφήστε κενό
τουλάχιστον 2 ίντσες (5 εκατοστά) για την κυκλοφορία του αέρα στα πλαϊνά, το
μπροστινό μέρος και το πίσω μέρος της μονάδας.
Για την ασφάλειά σας, ποτέ μην κόψετε, αφαιρέσετε ή απενεργοποιήσετε την
ηλεκτρική (γείωση) σύνδεση από το φις. Μη χρησιμοποιήσετε ποτέ προσαρμογέα
φις ή καλώδιο προέκτασης (μπαλαντέζα) με το Cooktop.
ΠΡΟΕΙΔΟΠΟΙΗΣΗ: Ένα εσφαλμένα γειωμένο φις μπορεί να έχει ως
αποτέλεσμα την ηλεκτροπληξία. Παρακαλείστε να συμβουλευτείτε αρμόδιο
ηλεκτρολόγο εάν έχετε τυχόν ερωτήσεις σχετικά με αυτές τις οδηγίες
γείωσης.
Πριν ξεκινήσετε:
Βεβαιωθείτε ότι αυτό το ηλεκτρικό καλώδιο είναι σταθερά συνδεδεμένο στη μονάδα
CookTek σας ΠΡΙΝ συνδέσετε το φις της μονάδας σε ηλεκτρική πρίζα και πριν
προσπαθήσετε να θέσετε τη μονάδα σε λειτουργία.
●Μην αγγίξετε την κεραμική πλάκα (ή το άνω μέρος του Cooktop) αμέσως μετά
τη χρήση. Η θερμότητα από την κοιλότητα θα μεταφερθεί στην κεραμική πλάκα.
Ως εκ τούτου, αυτή θα είναι πολύ ζεστή για να την αγγίξετε.
●Οι εργασίες επισκευής του προϊόντος αυτού πρέπει να πραγματοποιούνται
μόνο από εξουσιοδοτημένο αντιπρόσωπο επισκευών ή από προσωπικό της
CookTek. Μην επιχειρήσετε να ανοίξετε τη μονάδα ή να εκτελέσετε οποιαδήποτε
εργασία επισκευής σε αυτήν. Για πληροφορίες σχετικά με τις επισκευές,
επικοινωνήστε με την CookTek στον τηλεφωνικό αριθμό 1-312-563-9600.
●Η συσκευή αυτή πρέπει να είναι γειωμένη. Συνδέστε μόνο σε σωστά γειωμένη
πρίζα. Πριν τη λειτουργία, διαβάστε τις οδηγίες γείωσης και τις απαιτήσεις
ηλεκτρικής εγκατάστασης στη σελίδα 3 του παρόντος φυλλαδίου. Μη
χρησιμοποιείτε καλώδιο προέκτασης (μπαλαντέζα).
Prima di mettere in funzione il piano cottura, eseguire le seguenti operazioni:
●Rimuovere tutto il materiale di imballaggio.
●Collocare l'unità su una superficie asciutta, piana, rigida, stabile e non
infiammabile.
●Tenere l'unità lontana da altre fonti di calore e lasciare almeno 5 centimetri di
spazio per consentire la circolazione dell'aria tutto intorno all'unità.
ITALIAN
GREEK
Plug the buffet into a grounded, single-phase receptacle. Models will run on 100-
120VAC drawing up to 650W, or on 200-240VAC drawing a maximum of 650W.
Check rating plate on unit to verify correct voltage and wattage. Voltages below
120VAC or 240VAC can result in less than rated power and slower heating times.
This appliance is designed for holding food products only.
This unit is equipped with SmarTag™technology, using RFID to provide precise
temperature control.
This unit requires a Magneeto™II for
operation. The Incogneeto™unit will not work
with a Magneeto™I module or an RFID
equipped chafing dish.
Note: For proper operation, an independent,
dedicated circuit should be used for up to 3 units installed on a 15A (120VAC)
circuit, 4 units installed on a 20A (120VAC) circuit, or up to 5 units installed
on a 20A (240VAC) circuit.
To operate this buffet unit
●Press the Power button to turn the unit on. The green LED next to
the power putton will illuminate.
●Place a Magneeto™II on the counter top and position it
over top of the unit until the LED begins flashing and the
SmarTag™LED will illuminate.
●Place an induction compatible dish on the top of the Magneeto™II. The Pan
Detect LED will illuminate.
Make sure the dish is covering the temperature sensor on the Magneeto™
II, but do not cover the RFID tag. The unit will start at 80°F, or the last
entered temperature. Press the Up and Down Arrows to select
desired temperature from the preset choices.
● Fahrenheit Settings (80-190 degrees): 80, 150, 160, 165, 170, 175, 180,
185, 190
● Celsius Settings (30-85 degrees): 30, 40, 50, 60, 65, 70, 75, 80, 85)
●Once you have chosen your preferred temperature, the unit will begin to heat
the dish. The letter F or C will flash when the sidh is heating. When the dish
has reached the set temperature, the letter F or C will remain solid on the
display.
●To lock the controls, press the Lock button three times (the
red LED to the right of the lock button will illuminate to
indicate the unit is locked). This will prevent temperature settings from being
changed. The Power button will continue to funciton while locked. To unlock
the controls, press the lock button three more times.
●When you are finished using the unit, press the Power button. The
green Power LED will go out. Remove the dish from the unit.
GENERAL OPERATION
Manual Incogneeto 12040_A USINTL
CONTROL BOX
CONFIGURATION
5 18
Pour votre sécurité, ne jamais couper, déconnecter ou désactiver le raccordement
électrique (terre) de la prise de courant. Ne jamais utiliser un adaptateur ou une
rallonge électrique avec l’appareil Cooktop.
MISE EN GARDE : Une prise de courant incorrectement raccordée à la terre
engendre un risque de choc électrique. Pour toute question concernant ces
instructions de mise à la terre, consulter un électricien qualifié.
Avant de commencer :
S’assurer que le câble d’alimentation est solidement fixé à l’appareil CookTek
AVANT de raccorder l’appareil à une prise de courant et d’essayer de le faire
fonctionner.
● Ne pas toucher la plaque de céramique (ou la partie supérieure de l’appareil
Cooktop) immédiatement après utilisation. La chaleur de la casserole se
transmet à la plaque de céramique, aussi celle-ci est chaude au toucher.
● L’entretien de cet appareil ne peut être effectué que par un réparateur agréé ou
par un membre du personnel de CookTek. Ne jamais essayer d’ouvrir l’appareil
ni de le réparer. Pour des informations concernant l’entretien, contacter
CookTek au +1-312-563-9600.
● Cet appareil doit être raccordé à la terre. Le brancher exclusivement à une
prise de courant correctement raccordée à la terre. Avant utilisation, lire les
instructions de raccordement à la terre, ainsi que les exigences en matière
d’installation électrique figurant à la page 3 du présent manuel. Ne pas utiliser
de câble de rallonge.
Vor Inbetriebnahme des Cooktop verfahren Sie bitte wie folgt:
● Entfernen Sie das gesamte Verpackungsmaterial.
● Stellen Sie das Gerät auf eine trockene, ebene, harte, stabile und nicht
brennbare Fläche.
● Halten Sie das Gerät von anderen Wärmequellen fern und lassen Sie um das
Gerät herum (vorne, hinten und seitlich) mindestens 5 cm für die Luftzirkulation
frei.
Zu Ihrer eigenen Sicherheit darf das Erdungskabel keinesfalls vom Stecker
abgetrennt, entfernt oder in schadhaftem Zustand verwendet werden. Benutzen Sie
für Ihren Cooktop niemals einen Steckeradapter oder ein Verlängerungskabel..
WARNHINWEIS: Ein nicht fachgemäß geerdeter Stecker kann zu einem
Stromschlag führen. Falls Sie noch Fragen zu diesen Anweisungen in
Zusammenhang mit Schutzkontakt und Erdung haben, wenden Sie sich bitte
an einen Elektrofachmann.
Bevor Sie beginnen:
Dieses Netzkabel muss fest mit dem CookTek verbunden sein, BEVOR Sie das
Gerät an die Steckdose anschließen und es in Betrieb nehmen.
● Berühren Sie die Keramikplatte (oder Oberfläche des Cooktop) nicht
unmittelbar nach Gebrauch. Die Hitze der Pfanne überträgt sich auf die
Keramikplatte, die dann ebenfalls heiß wird.
GERMAN
Starting with the unit off, hold down the Up Arrow while pressing
the Power button. Then use the Down Arrow to select the
desired scale. Powering the unit off completes the selection.
Note: if a button is not pressed for more than five minutes, the unit will power off
keeping the previously set temperature scale.
Starting with the unit off, hold down both the Up and
Down Arrows and press the Power button. Use the
arrows to select “NUM” and press the Lock button. Use the arrows again to select
“PART” or “FULL” for the partial or full set of temperatures. Press the Power button
to set the value.
CookTek’s buffet is in conformance with UL 197 and CSA 22.2 No. 109 standards
and bears the commercially rated approvals. CookTek’s buffet is in conformance
with European Economic Area standards and bears the CE marking signifying
European Conformity.
APPROVED FOR COMMERCIAL USE
Manual Incogneeto 12040_A USINTL
● Starting with the unit off, hold the Down Arrow while pressing
the Power button.
● The display will start with the text “CLR.” Use this to clear the tag (the unit will
no longer enter auto mode). Otherwise, use the Up and Down Arrows to select
a temperature.
● To set the tag, press the Lock Button twice. The display will
read “TAG SET.”
● Repeat if necessary with other Magneeto™ IIs.
● With Incogneeto™ or MB061 unit turned on, place Magneeto™ II on counter
top in expected vicinity of unit (ribbed side down). Slowly slide the Magneeto™
II around until the red light flashes.
● Placement where the light flashes brightest is the optimum position.
● Place induction compatible dish on top of Magneeto™ II for warming. Make
sure the dish covers the temperature sensor, but do not cover the RFID
tab with the dish. Locating may also be performed with the dish already on
the Magneeto™ II.
RFID tab
Red LED
Temperature
Sensor Dome
PROGRAMMNG A MAGNEETO™II
MAGNEETO™II OPERATION (MGRFID02, 607700)
CHANGE TEMPERATURE SCALE
CHANGE TEMPERATURE OPTIONS (SHORT/LONG)
17 6 Manual Incogneeto 12040_A USINTL
Voordat u begint:
Controleer eerst of dit snoer stevig aan uw CookTek-apparaat is bevestigd VOOR-
DAT u de stekker van het toestel in het stopcontact steekt en u probeert het te ge-
bruiken.
● Raak de keramische plaat (of de bovenkant van de kooktop) nooit onmiddellijk
na gebruik aan. De hitte van de pan wordt op de keramische plaat overgebracht
zodat deze heet is bij aanraking.
● Dit product mag uitsluitend worden gerepareerd door een geautoriseerd
servicebedrijf of door personeel van CookTek. Probeer niet om het toestel open
te maken of op enige wijze te repareren. Neem voor informatie over onderhoud
en reparatie contact op met CookTek op 001-312-563-9600.
● Dit toestel moet worden geaard. Alleen aansluiten op een goed geaard
stopcontact. Lees voor het gebruik de aardingsinstructies en de vereisten voor
de elektrische aansluiting op pagina 3 van dit boekje. Gebruik geen
verlengsnoer.
Ennen keittotason käyttöä toimi seuraavasti:
● Poista kaikki pakkausmateriaalit.
● Laita laite kuivalle, tasaiselle, kovalle, tukevalle ja palamattomalle pinnalle.
● Pidä laite erossa muista lämmönlähteistä ja jätä laitteen sivuille, eteen ja taakse
vähintään 10 cm ( 2 tuumaa) vapaa tilaa ilmalle kiertää.
Turvallisuussyistä älä koskaan leikkaa, irrota tai pura sähköliitoksia (maadoitusjo-
htoa) pistokkeesta. Älä koskaan käytä keittotason kanssa sovitinpistoketta tai jatko-
johtoa.
VAROITUS: Väärin maadoitettu pistoke voi aiheuttaa sähköiskun. Neuvottele
valtuutetun sähköasentajan kanssa, jos sinulla on kysyttävää näistä maadoi-
tusohjeista.
Ennen kuin aloitat:
Varmista, että tämä virtajohto on tiukasti kiinnitetty CookTek:iin ENNEN laitteen pis-
tokkeen työntämistä pistorasiaan ja ennen käyttökokeilua.
● Älä koske keraamista levyä (keittotason päällä) heti käytön jälkeen. Astian
kuumuus siirtyy keraamiseen levyyn kuumentaen sen liian kuumaksi koskettaa.
● Tätä tuotetta saa huoltaa ainoastaan valtuutettu huoltopiste tai CookTekin
henkilökunta. Älä yritä avata laitetta ja suorittaa sille minkäänlaisia huoltotoimia.
Tietoja huollosta saat soittamalla CookTekiin numeroon +1-312-563-9600.
● Tämä laite täytyy suojamaadoittaa. Liitä ainoastaan oikein suojamaadoitettuun
pistorasiaan. Ennen käyttöä lue maadoitusohjeet ja sähköasennusvaatimukset
tämän lehtisen sivulta 3. Älä käytä jatkojohtoa.
Avant d’utiliser l’appareil Cooktop, effectuer les opérations suivantes :
● Retirer tous les matériaux d’emballage.
● Placer l’appareil sur une surface sèche, plane, solide, stable et non
inflammable.
● Placer l’appareil à distance de toute autre sources de chaleur et laisser un
espace libre d’au moins 5 cm (2 pouces) des deux côtés, à l’avant et à l’arrière
de celui-ci pour permettre la circulation de l’air.
FRENCH
FINNISH
● To enable/disable the timer feature, see “Setting the Timer” below.
● If the timer is enabled, the timer will start counting when a pan is
placed on the unit and the Heating or At Temp LED will turn on.
● The timer will count up to the preset interval (in minutes). When the
interval is reached, the unit will start to beep once per second to alert the
operator and flash “DonE” on the display. The unit will continue to maintain the
temperature of the pan when the timer is expired.
● The timer is reset when the pan is removed from the unit and the
Heating or At Temp LED turns off. The next time a pan is placed on
the unit the timer will start again from the beginning.
● To view the elapsed time from when the pan was place on the unit,
press the Lock button once. This will display the time (in minutes) from
when the pan was placed on the unit for 5 seconds. After 5 seconds
the normal temperature display will return.
The IHW units are equipped with a timer alarm that can be set to alert the operator
when a apan has been on the unit for a period of time up to 240 minutes (4
hours).
To enable/disable the timer:
● Starting with the unit off, hold the Down Arrow while pressing the
Power Button.
● Release the buttons when the display comes on. Use the
Up and Down Arrows to toggle through the options until
“t En” is shown on the display. Press the Lock Button once to select the enable
option.
● Press the Up and Down arrows to toggle between the two
setting options “on” and “off.” When the desired option is
displayed, press the Lock Button once to enter this option. The display will flash
three times to indicate the option has been saved.
● Press the Power Button to exit this mode.
To set the timer interval:
● Starting with the unit off, hold the Down Arrow while pressing the
Power Button.
● Release the buttons when the display comes on. Use the
Up and Down Arrows to toggle through the options until
“t Int” is shown on the display. Press the Lock Button to select the interval
option.
● Press the Up and Down Arrows to increase or decrease the
amount of time desired for the timer interval. When the
desired time (displayed in minutes) is shown, press the Lock Button to enter this
option. The display will flash three times to indicate the option has been saved.
● Press the Power Button to exit this mode.
TIMER OPERATION
SETTING THE TIMER
7 16 Manual Incogneeto 12040_A USINTL
MANUAL TRANSLATION ADDENDUM - DUTCH
Doe het volgende voordat u uw kooktop gaat gebruiken:
● Verwijder al het verpakkingsmateriaal
● Zet het toestel op een droge, vlakke, harde, stabiele en onbrandbare
ondergrond
● Houd het toestel uit de buurt van andere warmtebronnen en zorg dat er aan de
voor- en achterkant en de zijkanten minstens 5 cm vrij is voor luchtcirculatie.
Voor uw veiligheid mag u nooit de elektrische (massa) aansluiting uit de stekker
snijden, verwijderen of uitschakelen. Gebruik nooit een aangepaste stekker of een
verlengsnoer met de kooktop.
WAARSCHUWING: Een verkeerd geaarde stekker kan u een elektrische schok
bezorgen. Raadpleeg een erkende elektricien als u vragen heeft over deze
aardingsinstructies.
UNIT DIMENSIONS
Dimensions
inches mm
A 16.23 412
B 14.91 378
C 3.90 99
D 19.76 502
E 17.50 444
F 4.17 105
G 3.81 97
H 2.46 62
J 3.26 83
K 1.91 49
L 1.02 26
M 2.25 57
N 2.90 74
Symptom Probable Cause Possible Solution
No power
(No lights or fan
noise)
● Unit unplugged
● No power to receptacle
● Plug unit into appropriate
receptacle
● Make sure that receptacle is
energized
● Check wall switches
● Check circuit breaker
● Plug a different electronic device
into the receptacle to make sure
that power is present
Pan does not heat ●Pan is not induction
efficient
● Pan not centered
● Use induction efficient pan
● Center pan
Buffet suddenly
stops heating
●Possible power brown
out
● Circuit shared with
another electrical device
● Safety shut-off engaged
● Assure proper voltage/power levels
● Make sure the buffet is not sharing
a circuit with other electrical
devices
● The safety shut-off will engage if an
empty pan is left on the buffet
surface while the unit is working at
full power. Make sure that the
buffet surface is clear. Wait 15-20
minutes for the unit to reset.
Pan does not get
hot enough even
though power levels
are set to maximum
- induction efficient
pan in use
● Extension cord in use
● Circuit shared with
another electrical device
● DO NOT use extension cords.
Extension cords may affect the
power levels reaching the
appliance.
● Make sure that the buffet is not
sharing a circuit with other
electrical devices.
Pan heats unevenly,
does not maintain
heat level, or
overheats
● Pan is not induction
efficient
● Pan bottom may not be
flat enough
● Pan not centered
● Pan diameter is less
than 7” or more than 12”
● Use induction efficient pan
● Use flatter pan
● Center pan
● Use an induction efficient pan that
is between 7”-12” (17.8-30.5cm) in
diameter
TROUBLESHOOTING
15 8 Manual Incogneeto 12040_A USINTL
In the event of a possible malfunction, your CookTek Incogneeto™ Buffet will
display an error code on the alphanumeric display. Some models will beep a
specific number of times, indicated by the error and flash the lights on the control
box. Please consult the following table when encountering an error code.
To reset error conditions, remove the pan from the unit and press the Power button,
or unplug the unit.
Error Error Cause Displayed Message Troubleshooting
1
Broken
Temperature
Sensor
E-01 Service required
3Over current (peak) E-03 Try different cookware. Service
may be required.
6High line voltage E-06
To reset, unplug unit, wait 5
seconds, and plug in again. If
problem persists, have an
electrician monitor the line
voltage.
7Harware failure E-07 Service required.
8Zero cross failure E-08
Turn unit off, then on. Plug unit
into outlet on different circuit
breaker. If problem persists,
service is required on device
10 Magneeto™II RTD
Failure E-10
Magneeto™II needs repair.
Service needed for Magneeto™
II.
11 Tag communication E-11 Ensure the RFID tag on the pan is
properly located.
12 RFID reader failure E-12 Service required.
13 User interface
error E-13
Check control panel
connection, cycle power.
Service required
16 Critical error E-16 Call dealer for service.
Service required.
ERROR CODES
Incogneeto™ Buffet Unit
Your CookTek Induction Buffet is easy to keep clean. Be sure to follow these easy
instructions:
● Turn the unit OFF and remove the plug from any power outlets prior to cleaning.
● Never immerse the buffet in water or put in in the dishwasher.
Magneeto™ II (MGRFID02, 607700)
Cleaning:
● When needed, clean the Magneeto™ II with a mild soap or detergent.
● Do not place the Magneeto™ II in the dishwasher.
Care and Cautions:
● The induction unit RFID antenna is located in the back of the unit. The
Magneeto™ II RFID tab must be positioned over the antenna.
● Use the Magneeto™ II ONLY with Incogneeto™ and MB061 series 650 watt
RFID induction units. DO NOT use the Magneeto™ II with any other induction
appliance, as it may be damaged.
● Pan bottom size should be between 7” and 12” (17.8-30.5 cm) in diameter. The
dish/pan bottom must be flat and in contact with the temperature sensor dome
or overheating will result.
● Some upward bowing of the Magneeto™ II when hot and a dish is removed is
normal and will disappear with cooling or when a dish is placed on top.
● Do not significantly bend or twist the Magneeto™ II as damage may result.
● Never heat an empty pan. It may damage the buffet or cookware, and overheat
the unit. When overheating occurs, an error code will flash on the display and
the buffet will shut itself off automatically. When the internal temperature
returns to normal, the buffet can be used again.
● Remember to turn the buffet off after each use.
● Keep the buffet away from gas and electric ranges or open flames. Do not
place in the oven. If the ambient air temperature is above 110°F, the buffet may
not function properly.
● Be sure to dry off the outside of the pan before use. Water droplets on the
outside of the pan may begin to boil and spatter as the pan temperature rises.
● Do not use aluminum foil on top of the buffet.
● Do not use the buffet near a faucet, swimming pool, sink, or other areas where
water can be found.
● Never store the buffet outside or upside down.
● Do not obstruct, block, or alter the air entrance or outlet. Do not stick foreign
objects into these openings.
● Do not strike or damage the buffet. Do not put the buffet in your luggage.
Throwing or dropping the buffet can damage the internal components or crack
the buffet, voiding your warranty. If the buffet becomes cracked, unplug
immediately and do not use.
CARE AND CLEANING
IMPORTANT INFORMATION
9 14 Manual Incogneeto 12040_A USINTL
All commercial cooking and holding equipment manufactured by CookTek is
warranted against defects in materials and workmanship for a period of three years
from the date of shipment from CookTek’s factory. All non-electrical equipment
such as pans, bags, and pellet assemblies are warranted against defects in
materials and workmanship for a period of 90 days from the date of shipment from
CookTek’s factory.
IMPORTANT! A valid proof of purchase, and Serial Number (s) showing date of
purchase is required to obtain Warranty Service.
This warranty is for the benefit of the original purchaser and is non-transferable.
Any defects in materials or workmanship, which are brought to the attention of
CookTek by written notification within the aforesaid warranty period will be repaired
or replaced, at CookTek’s discretion, with new or recertified products or parts. THIS
IS THE SOLE REMEDY FOR ANY BREACH OF THIS WARRANTY. IN NO
EVENT WILL COOKTEK BE LIABLE FOR DAMAGES OF ANY KIND, WHETHER
DIRECT OR INDIRECT, SPECIAL OR CONSEQUENTIAL. THIS WARRANTY IS
THE COMPLETE AND ONLY WARRANTY, EXPRESS OR IMPLIED IN LAW OR
FACT, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF
MERCHANTABILITY, SUITABILITY, QUALITY, OR FITNESS FOR ANY
PARTICULAR PURPOSE. THIS WARRANTY DOES NOT INCLUDE ANY THIRD
PARTY INSTALLATION, REMOVAL OR DAMAGE COSTS including (but not
limited to) LABOR, MATERIALS AND TRAVEL FOR CAULKING IN DROP-IN
(“BUILT-IN”) UNITS, OR REPAIRS / REPLACEMENT OF FUSES, BREAKERS,
MILLWORK AND / OR COUNTER-TOPS).
This warranty is void if it is determined that upon inspection by CookTek or one its
Authorized International Distributor s that the equipment has been modified,
misused, misapplied, improperly installed, or damaged in transit or by fire, flood or
act of God. Broken Glass-Ceramic tops are considered abuse and are NOT
covered. Warranty will be considered void if the serial nameplate has been
removed or defaced or if the unit has been opened or modified in any way or
service has been attempted by unauthorized personnel.
The prices charged by CookTek for its products are based upon the limitations in
this warranty. Seller’s obligation under this warranty is limited to the repair of
covered defects without charge by CookTek or one of its Authorized International
Distributors
This warranty is valid in the continental United States of America (USA) and
Canada only. It is valid only if purchased through an authorized Cooktek
Representative or Dealer. To receive Warranty Service in the USA, please call
CookTek’s Customer Service Department at 1 (888) 266-5835, or (312) 563-9600.
A Returns Authorization (RA) number will be issued along with instructions for
returning goods for service (or their replacement). The RA number must be written
clearly or printed on the outside of the return shipping container, or on the address
label when returning units for service (continued...)
WARRANTY STATEMENT - US & CANADA ONLY
● To reduce the risk of fire, electric shock or injury, please read, follow, and save
all instructions.
● Never immerse the cords, plugs, or appliance in water.
● Supervise carefully when appliance is used near children. Keep children away
from appliance when in operation.
● Always unplug appliance immediately after use and allow for cooling time if
handling, transporting, or storing.
● Do not use any appliance that has a damaged cord or plug, or one that has
malfunctioned or been damaged. Consult the warranty and follow instructions
for service.
● Do not use any accessories or attachments that are not recommended by the
manufacturer. Use of unapproved accessories may cause injuries and void the
warranty.
● The pan on the appliance will heat continuously as long as the power is ON.
The pan will be hot and caution should be exercised when working on or near
the appliance.
● Do not let the power cord touch hot surfaces or hang over the edge of the
counter. Do not move the appliance with electric power is connected. Do not
move the appliance while a hot pan or pan containing hot liquids is on top of the
appliance.
● To disconnect the appliance, press the Power button and wait for the LED to no
longer be illuminated. You may then remove the plug from the outlet.
● Do not use CookTek Buffet for anything other than its intended use as described
in this manual. This unit is designed to heat food and is not intended for
laboratory or industrial use.
● Do not put food or unopened cans on the buffet surface.
● This product may only be serviced by an authorized service agent or by
CookTek personnel. Do not attempt to open the unit or perform service of any
kind. For service information, contact CookTek at +1 (312) 563-9600.
● This appliance must be grounded. Connect only to a properly grounded outlet.
Before operating, read grounding instructions and Electrical Installation
Requirements on page 2 of this booklet. Do not use an extension cord.
● Do not overcook food or leave appliance unattended while in use.
● In the unlikely event of a grease fire, smother flame by covering pan with a
tight-fitting lid, cookie sheet, or flat tray. DO NOT USE WATER. When the fire
is under control, turn off appliance and unplug from wall.
● Use only induction compatible and efficient cookware.
● Place buffet on a level, hard, stable, non-flammable surface before use.
IMPORTANT SAFETY PRECAUTIONS
13 10 Manual Incogneeto 12040_A USINTL
Units received without an RA number will be refused at our shipping dock and may
encounter a delay in service. Units must be taken or shipped to the factory with
transportation charges prepaid for service. CookTek will provide return freight. If
instead, the unit(s) is handled under CookTek’s Advanced Replacement Program
(ARP), CookTek will pay for shipping both ways, but the unit(s) being replaced must
be returned. Instructions and alternate courses of action will be provided by
Customer Service. Please save all packaging materials for possible use in
shipping. CookTek assumes no liabilities whatsoever for any damages incurred in
transit. PLEASE BE SURE TO USE ADEQUATE PACKAGING AND A RELIABLE
SHIPPING METHOD OR, IF USING THE ARP PROGRAM, USE THE SAME BOX
THE REPLACEMENT UNIT ARRIVED IN FOR THE RETURN.
OUTSIDE THE USA AND CANADA
CookTek offers NO warranty outside of the USA and Canada. Warranty is
offered and performed at the discretion of CookTek’s local Authorized International
Distributor. Contact details can be found at www.cooktek.com/find-rep, or by calling
+1 (312) 563-9600.
For additional information and other details concerning warranty, please contact our
Customer Service Department at:
CookTek Induction Systems, LLC• www.cooktek.com
In the USA, Tel: (888) COOKTEK, 1 (888) 266-5835 • Fax: 1 (888) 266-5329
Outside the USA, Tel: +1 (312) 563-9600 • Fax: +1 (312) 432-6220
BEST PRACTICES
Stone is a natural material with random defects in any given piece. Cracking can
occur due to these defects alone. Cracks can also occur when pre-existing weak
points are subjected to additional stress or forces. Mechanical forces caused by
poor support, shifting joints in the support structure, and weight distribution will
cause excess stress on the stone. Heat differentials that cause one portion of the
stone to try to expand while other portions remain fixed (ie, heat lamps, heat from
equipment below stone, hot items on the stone, etc.) will cause excess stress. In
extensive testing conducted by CookTek, no natural stone was found to interfere
with the performance of the wireless communcations, or absorb excess heat from
the electromagnetic induction waves associated with the Incogneeto and Magneeto
2 equipment.
● Any temperature gain that occurs inside the cabinet where an Incogneeto is
mounted contributes to heating the stone. Be sure to supply adequate
ventilation.
● Tensile strength of natural stone is proportionally linear with thickness -
prolonged intensive use applications are best suited with 3cm stone.
● 3cm thick natural stone dissipates heat much better than 2cm stone. For
prolonged intensive use applications, thicker stone is more durable.
● The stone is not generally heated by the induction waves, but some heating will
occur from radiation back from a hot pan. Allowing as much stone around the
edge of the Incogneeto as possible will act as a buffer and improve the strength
of the whole system.
● CookTek recommends that natural stone be 3cm thick in high use applications.
Synthetic or “engineered stone” at 2cm thick is acceptable in all applications
(but may also require plywood substrate).
● CookTek further recommends that cabinets have sufficient ventilation to keep
interior compartment as close to room temperature as possible.
● At least 8 inches of additional stone surface should be allowed from the edge of
the Incogneeto to the final edge of any piece of stone.
● Heat lamps should not be used above an Incogneeto unless they are
interlocked to prevent heating when a pan is not present.
● Do not put the Incogneeto near the mechanical support seam in the cabinet.
INSTALLATION RAIL SYSTEM FORMULA
To ensure maximum functionality of the Incogneeto unit, the combined thickness of
the countertop and wood substrate must be between 30 and 40mm (1.18” to 1.57”).
Thickness of stone (countertop) + Thickness of wood substrate = Combined
thickness of stone/wood substrate (this measurement should be 30-40mm)
Rail system conversions: 1.18 inches = 30mm
1.26 inches = 32mm
1.57 inches = 40mm Match total thickness to
closest rail setting and install
locknuts
11 12 Manual Incogneeto 12040_A USINTL
INSTALLATION INSTRUCTIONS
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
in andere talen
- English: CookTek B652.U2 User manual
- français: CookTek B652.U2 Manuel utilisateur
- português: CookTek B652.U2 Manual do usuário
- dansk: CookTek B652.U2 Brugermanual
- polski: CookTek B652.U2 Instrukcja obsługi
Andere documenten
-
Ninja OL650EU Handleiding
-
-
Eico Aspira Auto Handleiding
-
Wolf ICBCI36560C-B Gebruikershandleiding
-
Ninja ON400EU Handleiding
-
Haier UM 33803056 Handleiding
-
Falmec Quantum Pro Easy Handleiding
-
Airforce Domino flex 38 Handleiding
-
BORETTI VP946IXBE LINEA PRINCIPALE de handleiding