Documenttranscriptie

English Caractéristiques Input Channels...................................................................page 12 With up to 16 (MG166CX/MG166C: 10) mic/line inputs or up to four stereo inputs, the MG mixer can simultaneously connect to a wide range of devices: microphones, line-level devices, stereo synthesizers, and more. Canaux d’entrée.................................................................page 48 Avec 16 entrées micro/ligne (MG166CX/MG166C: 10) ou quatre entrées stéréo maximum, la console de mixage MG peut connecter simultanément une grande variété d’appareils : micros, appareils de ligne, synthétiseurs stéréo, etc. Compression......................................................................page 10 Compression increases the overall level without introducing distortion by compressing excessive peaks in the signals from microphones and guitars. Compression......................................................................page 46 La compression augmente le niveau général sans engendrer de distorsion en comprimant les pics excessifs des signaux des micros et des guitares. AUX Sends and Stereo AUX Return.................................page 16 You can use the AUX SEND jack to feed the signal sent to an external signal processor, and then return the processed stereo signal through the RETURN jack. Envois AUX et retour AUX stéréo.....................................page 52 Vous pouvez utiliser la prise jack AUX SEND pour envoyer le signal vers une unité de traitement de signaux externes, puis pour renvoyer le signal stéréo traité via la prise jack RETURN. High-quality digital effects (MG166CX)....................pages 15, 19 With digital effects built in, the MG166CX can deliver a wide range of sound variations all by itself. Effets numériques de qualité supérieure (MG166CX)...pages 51, 55 Grâce aux effets numériques intégrés, la console MG166CX peut proposer de nombreuses variations de sons. Funktionen Características Eingangskanäle..................................................................Seite 30 Mit bis zu 16 Mikrofon-/Line-Eingängen (MG166CX/MG166C: 10) oder bis zu vier Stereoeingängen können viele Geräte gleichzeitig am MG-Mischpult angeschlossen werden: Mikrofone, Geräte mit Leitungspegel, Stereo-Synthesizer uvm. Canales de entrada.........................................................página 66 Con un máximo de 16 entradas de micrófono/línea (MG166CX/MG166C: 10) o cuatro entradas estereofónicas, la mezcladora MG puede conectarse simultáneamente con una gran variedad de dispositivos: micrófonos, dispositivos de nivel de línea, sintetizadores estereofónicos, etc. Kompression......................................................................Seite 28 Kompression erhöht den Durchschnittspegel, ohne Verzerrung hinzuzufügen, indem übermäßige Pegelspitzen der Signale von Mikrofonen oder Gitarren komprimiert werden. AUX Sends und Stereo AUX Return.................................Seite 34 Von der AUX SEND-Buchse können Sie das Signal einzeln an einen externen Signalprozessor führen, und das verarbeitete Stereosignal über die RETURN-Buchse zurück in das Pult führen. Hochwertige Digitaleffekte (MG166CX)....................Seiten 33, 37 Mit den eingebauten digitalen Effekten kann das MG166CX aus sich heraus eine Reihe von Klangvariationen liefern. Español Features Français Deutsch Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones Compresión.....................................................................página 64 La compresión aumenta el nivel general sin causar distorsión, mediante la compresión del exceso de picos en las señales de los micrófonos y guitarras. Envíos AUX y retorno AUX estereofónico....................página 70 Puede utilizar la toma AUX SEND para introducir la señal enviada en un procesador de señales externo y luego devolver la señal estereofónica procesada a través de la toma RETURN (retorno). Efectos digitales de alta calidad (MG166CX)........páginas 69, 73 Gracias a sus efectos digitales incorporados, la mezcladora MG166CX puede producir por sí misma una amplia gama de variaciones de sonido. EN DE FR ES  IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured makings identifying the terminals in your plug proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. * This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (2 wires) FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regula- tions does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to the MG166CX distributed by YAMAHA CORPORATION OF AMERICA, not the MG206C/MG166C. 2 MG206C/MG166CX/MG166C Owner’s Manual (class B)  PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device. • Do not expose the device to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings. • Use only the included power adaptor (PA-30 or an equivalent recommended by Yamaha). • Never insert or remove an electric plug with wet hands. • Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. Do not open • Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. If you notice any abnormality • If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the device, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. • If this device or the AC power adaptor should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Power supply/Power cord • Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. • When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. • To avoid generating unwanted noise, make sure there is adequate distance (50 cm or more) between the AC power adaptor and the device. • If this device is to be mounted in an EIA-standard rack, leave the back of the rack open and make sure that it is at least 10 cm away from walls or surfaces. Also, if this device is to be mounted with devices that tend to generate heat, such as power amplifiers, be sure to keep an adequate gap between this device and the heat-generating devices or install ventilation panels to prevent high temperatures from developing inside this device. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire. • Avoid setting all equalizer controls and faders to their maximum. Depending on the condition of the connected devices, doing so may cause feedback and may damage the speakers. • Do not cover or wrap the AC power adaptor with a cloth or blanket. Location • Before moving the device, remove all connected cables. • When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product all the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. • Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. • Do not place the device in an unstable position where it might accidentally fall over. • Do not block the vents. This device has ventilation holes at the bottom/rear to prevent the internal temperature from becoming too high. In particular, do not place the device on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire. • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Doing so may result in noise, both in the device itself and in the TV or radio next to it. (5)-4 1/2 MG206C/MG166CX/MG166C Owner’s Manual 3  Connections Handling caution • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. • When turning on the AC power in your audio system, always turn on the power amplifier LAST, to avoid speaker damage. When turning the power off, the power amplifier should be turned off FIRST for the same reason. • Do not insert your fingers or hands in any gaps or openings on the device (vents, etc.). • Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on the device (vents, etc.) If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel. • Do not use the device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. • Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors. XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-). Insert TRS phone jacks are wired as follows: sleeve: ground, tip: send, and ring: return. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. Always turn the power off when the device is not in use. Even when the power switch is in the “STANDBY” position, electricity is still flowing to the device at the minimum level. When you are not using the device for a long time, make sure you unplug the power cord from the wall AC outlet. The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualifi ed Yamaha service personnel about replacing defective components. The MG mixer may heat up by as much as 15 to 20°C while the power is on. This is normal. Please note that the panel temperature may exceed 50°C in ambient temperatures higher than 30°C, and use caution to prevent burns. * This Owner’s Manual applies to the MG206C/MG166CX/MG166C. The main differences between the three models are the number of input channels and whether the internal effects are included. The MG206C has 20 input channels while the MG166CX/MG166C have 16 channels. And only the MG166CX has internal effects. * In this manual the term “MG mixsers” refers to the MG206C, MG166CX and MG166C. * Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation. * Company names and product names herein are trademarks or registered trademarks of their respective companies. Copying of commercially available music or other audio data for purposes other than personal use is strictly prohibited by copyright law. Please respect all copyrights, and consult with a copyright specialist if you are in doubt about permissible use. Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. (5)-4 4 MG206C/MG166CX/MG166C Owner’s Manual 2/2  Introduction Thank you for your purchase of the Yamaha MG206C/MG166CX/MG166C mixing console. The MG206C/MG166CX/MG166C feature input channels suitable for a wide range of usage environments. And the MG166CX includes high-quality built-in digital effects that can provide some very serious sound. The mixer combines ease of operation with support for multiple usage environments. Please read through this manual carefully before beginning use, so that you will be able to take full advantage of this mixer’s superlative features and enjoy trouble-free operation for years to come. Contents Introduction .......................................... 5 Before Turning on the Mixer 1 Contents...........................................................5 Before Turning on the Mixer ............................5 Turning the Power On......................................5 Be sure that the mixer’s power switch is in the STANDBY position. CAUTION ■ Mixer Basics................................ 6 Quick Guide.......................................... 6 2 Making the Most of Your Mixer........... 8 Balanced, Unbalanced —What’s the Difference?..............................8 Signal Levels and the Decibel..........................8 To EQ or Not to EQ..........................................9 Ambience .......................................................10 The Modulation Effects: Phasing, Chorus, and Flanging ..................10 Compression..................................................10 ■ Reference .................................. 11 Setup ................................................... 11 Connect the power adaptor to the AC ADAPTOR IN connector (q) on the rear of the mixer, and then turn the fastening ring clockwise (w) to secure the connection. w 3 Troubleshooting................................. 20 Specifications..................................... 75 CAUTION • Be sure to unplug the adaptor from the outlet when not using the mixer, or when there are lightning storms in the area. • To avoid generating unwanted noise, make sure there is 50 cm or more between the power adaptor and the mixer. Turning the Power On Press the mixer’s power switch to the ON position. When you are ready to turn the power off, press the power switch to the STANDBY position. CAUTION Accessories q Plug the power adaptor into a standard household power outlet. Front & Rear Panels........................... 12 Channel Control Section ................................12 Digital Effects .................................................15 Master Control Section ..................................16 Digital Effect Program List (Only MG166CX).19 Jack List .........................................................19 Use only the included power adaptor (PA-30) or an equivalent recommended by Yamaha. Use of a different adaptor may result in equipment damage, overheating, or fire. Note that trace current continues to flow while the switch is in the STANDBY position. If you do not plan to use the mixer again for a long while, please be sure to unplug the adaptor from the wall outlet. • Owner’s Manual • AC power adaptor (PA-30)* * May not be included depending on your particular area. Please check with your Yamaha dealer. MG206C/MG166CX/MG166C Owner’s Manual 5  Mixer Basics Quick Guide Mixer Basics Getting Sound to the Speakers We begin by connecting a pair of speakers and generating some stereo output. Note that operations and procedures will vary somewhat according to the input devices you are using. 2 Microphones, instruments Speakers 2 Power Amp 1, 4 Headphones GAIN controls Monitor Speakers 4 3 PEAK indicators PHANTOM switch 4, 7 Equalizer Level meter PAN/BAL switches 5 ON switches 4 PFL switches 5 ST switches 1, 7 Channel faders 1, 3 POWER switch 6 2, 4 MG206C/MG166CX/MG166C Owner’s Manual 1, 6, 7 STEREO OUT Master fader MG206C  Mixer Basics Quick Guide 1 Be sure that your mixer is turned off and that all level controls* are turned all the way down. * STEREO OUT Master fader, Channel faders, GAIN controls, etc. NOTE 2 Set the equalizer and the PAN/BAL controls to their ▼ positions. Turn off any other external devices, then connect microphones, instruments, and speakers. NOTE • For information on connecting external devices see the Connection Example on page 11. • Connect electric guitars and basses through an intermediary device such as a direct box, preamp, or amp simulator. Connecting these instruments directly to the MG mixer may result in degraded sound and noise. 3 Turn on the ON and ST switches for each channel you are using. 6 Set the STEREO OUT Master fader to the “0” position. 7 Set the Channel faders to create the desired initial balance, then adjust the overall volume using the STEREO OUT Master fader. NOTE • To use the level meter to view the level being applied to the STEREO L/R buses, set the PFL switch off ( ) and the MONITOR switch to STEREO ( ). • If the PEAK indicator lights frequently, lower the Channel faders a little to avoid distortion. To avoid damage to your speakers, power up the devices in the following order: Peripheral devices → MG mixer → power amps (or powered speakers). Reverse this order when turning power off. CAUTION 4 5 If you are using condenser microphones that require phantom power, turn the MG mixer’s phantom power switch on before turning on the power to the power amp or powered speakers. See page 17 for more detail. Adjust the channel GAIN controls so that the corresponding PEAK indicators flash briefly on the highest peak levels. NOTE To use the level meter to get an accurate reading of the incoming signal level, turn the channel PFL switch on. Adjust the GAIN controls so that the level meter indication occasionally rises above the “▼” (0) level. Note that the PHONES jack outputs the prefader signal from all channels on which the PFL switch is ON so that those signals can be monitored via the headphones. MG206C/MG166CX/MG166C Owner’s Manual 7  Mixer Basics Making the Most of Your Mixer You’ve got yourself a mixer and now you’re ready to use it. Just plug everything in, twiddle the controls, and away you go … right? Well, if you’ve done this before you won’t have any problems, but if this is the first time you’ve ever used a mixer you might want to read through this little tutorial and pick up a few basics that will help you get better performance and make better mixes. Balanced, Unbalanced—What’s the Difference? In a word: “noise.” The whole point of balanced lines is noise rejection, and it’s something they’re very good at. Any length of wire will act as an antenna to pick up the random electromagnetic radiation we’re constantly surrounded by: radio and TV signals as well as spurious electromagnetic noise generated by power lines, motors, electric appliances, computer monitors, and a variety of other sources. The longer the wire, the more noise it is likely to pick up. That’s why balanced lines are the best choice for long cable runs. If your “studio” is basically confined to your desktop and all connections are no more than a meter or two in length, then unbalanced lines are fine—unless you’re surrounded by extremely high levels of electromagnetic noise. Another place balanced lines are almost always used is in microphone cables. The reason for this is that the output signal from most microphones is very small, so even a tiny amount of noise will be relatively large, and will be amplified to an alarming degree in the mixer’s high-gain head amplifier. Balanced noise cancellation To summarize Noise Hot (+) Cold (–) Phase inversion Phase inversion Noise cancelled Ground Noise-free signal Microphones Use balanced lines. Short linelevel runs Unbalanced lines are fine if you’re in a relatively noisefree environment. Long linelevel runs The ambient electromagnetic noise level will be the ultimate deciding factor, but balanced is best. Receiving device Source Cable Signal Levels and the Decibel Let’s take a look at one of the most commonly used units in Most professional mixers, audio: the decibel (dB). If the smallest sound that can be power amplifiers, and other types of equipment have inputs heard by the human ear is given an arbitrary value of 1, then + 20 dBu and outputs with a nominal level the loudest sound that can be heard is approximately of +4 dBu. 1,000,000 (one million) times louder. That’s too many digits 0.775 V The inputs and outputs on 0 dBu to deal with for practical calculations, and so the more approhome-use audio gear usually priate “decibel” (dB) unit was created for sound-related meahave a nominal level of –7.8 dBu surements. In this system the difference between the softest (–10 dBV). -20 dBu and loudest sounds that can be heard is 120 dB. This is a Microphone signal levels vary non-linear scale, and a difference of 3 dB actually results in a over a wide range depending on doubling or halving of the loudness. -40 dBu the type of microphone and the You might encounter a number of different varieties of the source. Average speech is dB: dBu, dBV, dBM and others, but the dBu is the basic deciabout –30 dBu, but the twitterbel unit. In the case of dBu, “0 dBu” is specified as a signal -60 dBu ing of a bird might be lower than level of 0.775 volts. For example, if a microphone’s output –50 dBu while a solid bass level is -40 dBu (0.00775 V), then to raise that level to 0 dBu drum beat might produce a level (0.775 V) in the mixer’s preamp stage requires that the signal as high as 0 dBu. be amplified by 100 times. A mixer may be required to handle signals at a wide range of levels, and it is necessary match input and output levels as closely as possible. In most cases the “nominal” level for a mixer’s input and outputs is marked on the panel or listed in the owner’s manual. 8 MG206C/MG166CX/MG166C Owner’s Manual  Mixer Basics Making the Most of Your Mixer To EQ or Not to EQ In general: less is better. There are many situations in which you’ll need to cut certain frequency ranges, but use boost sparingly, and with caution. Proper use of EQ can eliminate interference between instruments in a mix and give the overall sound better definition. Bad EQ—and most commonly bad boost—just sounds terrible. Cut for a Cleaner Mix For example: cymbals have a lot of energy in the mid and low frequency ranges that you don’t really perceive as musical sound, but which can interfere with the clarity of other instruments in these ranges. You can basically turn the low EQ on cymbal channels all the way down without changing the way they sound in the mix. You’ll hear the difference, however, in the way the mix sounds more “spacious,” and instruments in the lower ranges will have better definition. Surprisingly enough, piano also has an incredibly powerful low end that can benefit from a bit of low-frequency roll-off to let other instruments—notably drums and bass—do their jobs more effectively. Naturally you won’t want to do this if the piano is playing solo. The reverse applies to kick drums and bass guitars: you can often roll off the high end to create more space in the mix without compromising the character of the instruments. You’ll have to use your ears, though, because each instrument is different and sometimes you’ll want the “snap” of a bass guitar, for example, to come through. The fundamental and harmonic musical instruments. frequency ranges of some Cymbal Piano Bass Drum Snare Drum Bass Guitar Trombone Trumpet 20 50 100 200 500 1k 2k 5k 10 k 20 k (Hz) Fundamental: The frequency that determines the basic musical pitch. Harmonics: Multiples of the fundamental frequency that play a role in determining the timbre of the instrument. Some Frequency Facts The lowest and highest frequencies than can be heard by the human ear are generally considered to be around 20 Hz and 20,000 Hz, respectively. Average conversation occurs in the range from about 300 Hz to about 3,000 Hz. The frequency of a standard pitchfork used to tune guitars and other instruments is 440 Hz (this corresponds to the “A3” key on a piano tuned to concert pitch). Double this frequency to 880 Hz and you have a pitch one octave higher (i.e. “A4” on the piano keyboard). In the same way you can halve the frequency to 220 Hz to produce “A2” an octave lower. Boost with Caution MID Boost Signal Level (dB) If you’re trying to create special or unusual effects, go ahead and boost away as much as you like. But if you’re just trying to achieve a good-sounding mix, boost only in very small increments. A tiny boost in the midrange can give vocals more presence, or a touch of high boost can give certain instruments more “air.” Listen, and if things don’t sound clear and clean try using cut to remove frequencies that are cluttering up the mix rather than trying to boost the mix into clarity. One of the biggest problems with too much boost is that it adds gain to the signal, increasing noise and potentially overloading the subsequent circuitry. MID Flat LOW Boost HIGH Boost LOW Flat HIGH Flat LOW Cut HIGH Cut MID Cut Frequency (Hz) MG206C/MG166CX/MG166C Owner’s Manual 9  Mixer Basics Making the Most of Your Mixer Ambience Your mixes can be further refined by adding ambience effects such as reverb or delay. The MG166CX’s internal effects can be used to add reverb or delay to individual channels in the same way as external effects processors. (Refer to page 15). Reverb and Delay Time The optimum reverb time for a piece of music will depend on the music’s tempo and density, but as a general rule longer reverb times are good for ballads, while shorter reverb times are more suited to uptempo tunes. Delay times can be adjusted to create a wide variety of “grooves”. When adding delay to a vocal, for example, try setting the delay time to dotted eighth notes corresponding to the tune’s tempo. Reverb Tone Different reverb programs will have different “reverb tone” due to differences in the reverb time of the high or low frequencies. Too much reverb, particularly in the high frequencies, can result in unnatural sound and interfere with the high frequencies in other parts of the mix. It’s always a good idea to choose a reverb program that gives you the depth you want without detracting from the clarity of the mix. Reverb Level It’s amazing how quickly your ears can lose perspective and fool you into believing that a totally washedout mix sounds perfectly fine. To avoid falling into this trap start with reverb level all the way down, then gradually bring the reverb into the mix until you can just hear the difference. Any more than this normally becomes a “special effect.” For chorus and flanging the signal is delayed by several milliseconds, with the delay time modulated by an LFO, and recombined with the direct signal. In addition to the phasing effect described above, the delay modulation causes a perceived pitch shift which, when mixed with the direct signal, results in a harmonically rich swirling or swishing sound. The difference between chorus and flanging effects is primarily in the amount of delay time and feedback used—flanging uses longer delay times than chorus, whereas chorus generally uses a more complex delay structure. Chorus is most often used to thicken the sound of an instrument, while flanging is usually used as an outright “special effect” to produce otherworldly sonic swoops. Compression One form of compression known as “limiting” can, when properly used, produce a smooth, unified sound with no excessive peaks or distortion. A common example of the use of compression is to “tame” a vocal that has a wide dynamic range in order to tighten up the mix. With the right amount of compression you’ll be able to clearly hear whispered passages while passionate shouts are still well balanced in the mix. Compression can also be valuable on bass guitar. Too much compression can be a cause of feedback, however, so use it sparingly. Most compressors require several critical parameters to be set properly to achieve the desired sound. The MG compressor makes achieving great sound much easier: all you need to do is set a single “compression” control and all of the pertinent parameters are automatically adjusted for you. OUTPUT The Modulation Effects: (Min) Phasing, Chorus, and Flanging (Max) All of these effects work on basically the same principle: a portion of the audio signal is “time-shifted” and then mixed back with the direct signal. The amount of time shift is controlled, or “modulated”, by an LFO (Low-frequency Oscillator). For phasing effects the shift is very small. The phase difference between the modulated and direct signals causes cancellation at some frequencies and reinforces the signal at others and this causes the shimmering sound we hear. 10 MG206C/MG166CX/MG166C Owner’s Manual INPUT  Reference Setup Reference Guitar Rear panel Effect processor Recorder Powered monitor speakers Bass CD Player Powered speakers Synthesizer Microphone DI Effect processor (exciter) Headphones Powered monitor speakers MG206C MG206C/MG166CX/MG166C Owner’s Manual 11  Reference Front & Rear Panels Channel Control Section ● MG206C ● MG166CX/MG166C * A MG166C : EFFECT → AUX3 Channels 1 to 8 (Monaural) Channels 9 to 12 (Monaural) Channels 13/14 and 15/16 (Stereo) Channels 17/18 and 19/20 (Stereo) 1 1 5 6 7 12 4 Channels 9/10 and 11/12 (Stereo) 1 2 3 5 6 7 8 6 7 6 7 8 9 9 0 0 A Channels 7 and 8 (Monaural) 1 2 3 Channels 1 to 6 (Monaural) 9 9 0 0 A A B B A B B C C C C D E D E D E D E F G H F G H F G H F G H I I I I MG206C/MG166CX/MG166C Owner’s Manual Channels 13/14 and 15/16 (Stereo) 4  Reference Front & Rear Panels 1 MIC Input jacks 7 These are balanced XLR-type microphone input jacks. (1: Ground; 2: Hot; 3: Cold) 2 LINE Input Jacks (monaural channels) These are balanced TRS phone-jack line inputs. (T: Hot; R: Cold; S: Ground). You can connect either balanced or unbalanced phone plugs to these jacks. 3 LINE Input Jacks (stereo channels) These are unbalanced phone-jack stereo line inputs. 4 LINE Input Jacks (stereo channels) These are unbalanced stereo RCA pin jacks. Switch (High-Pass Filter) This switch toggles the HPF on or off. To turn the HPF on, press the switch in ( ). The HPF cuts frequencies below 80 Hz (the HPF does not apply to the line inputs of stereo input channels 3, 4). 8 COMP Control Adjusts the amount of compression applied to the channel. As the knob is turned to the right the compression ratio increases while the output gain is automatically adjusted accordingly. The result is smoother, more even dynamics because louder signals are attenuated while the overall level is boosted. NOTE On channels that provide multiple input jack options only one type of jack can be used at a time. NOTE 5 INSERT Jacks 9 PEAK indicator These jacks can be used to insert an external signal-processing device between the equalizer and fader of the corresponding monaural input channel. The INSERT jacks are ideal for connecting devices such as graphic equalizers, compressors, or noise filters into the corresponding channels. These are TRS (tip, ring, sleeve) phone jacks that carry both the send and return signal (tip = send/out; ring = return/in; sleeve = ground). Patching external devices via an INSERT jack requires a special cable such as illustrated below (insert cable sold separately). NOTE To the input jack of the external processor To the INSERT I/O jack Sleeve (Ground) Ring: IN Tip: OUT Tip: OUT Tip: IN To the output jack of the external processor CAUTION Avoid setting the compression too high, as the higher average output level that results may lead to feedback. The signal output from the INSERT jacks is reverse-phased. This should not be a problem when connecting to an effect unit, but please be aware of the possibility of phase conflict when connecting to other types of device. A reversedphased signal may result in degraded sound quality or even complete sound cancellation. The peak level of the post-EQ signal is detected, and the PEAK indicator lights red when the level reaches 3 dB below clipping. For XLR-equipped stereo input channels, both the post-EQ and post-mic-amp peak levels are detected, and the indicator lights red if either of these levels reaches 3 dB below clipping. 0 Equalizer (HIGH, MID and LOW) This three-band equalizer adjusts the channel’s high, mid, and low frequency bands. Setting the knob to the “▼” position produces a flat response in the corresponding band. Turning the knob to the right boosts the corresponding frequency band, while turning to the left attenuates the band. The monaural channels have MID frequency controls to adjust the midrange frequency band. The following table shows the EQ type, frequency, and maximum cut/boost for each of the three bands. Band Type Frequency HIGH Shelving 10 kHz MID Peaking 2.5 kHz* LOW Shelving 100 Hz Maximum Cut/Boost ±15 dB * The monaural channel MID frequency can be adjusted from 250 Hz to 5 kHz. The MID frequency is 2.5 kHz when the MID frequency control is set at the center position. 6 GAIN Control Adjusts the input signal level. To get the best balance between the S/N ratio and the dynamic range, adjust the gain so that the PEAK indicator 9 lights only occasionally and briefly on the highest input transients. The -60 to -16 scale is the MIC input adjustment range. The -34 to +10 scale is the LINE input adjustment range. MG206C/MG166CX/MG166C Owner’s Manual 13  Reference Front & Rear Panels A AUX, EFFECT Control Adjusts the level of the signal sent from the channel to the AUX and EFFECT buses. These knobs should generally be set close to the “▼” position. These controls send either the signal from immediately prior to the channel fader (pre-fader signal) or the signal after the channel fader (post-fader signal) to the corresponding buses. The types of signals sent by the AUX and EFFECT controls on each mixer model are as follows: Turn this switch on to send the signal to the buses. The switch lights orange when on. E PFL (Pre-Fader Listen) Switch This switch lets you monitor the channel’s pre-fader signal. Press the switch in ( ) so that it lights to turn it on. When the switch is on the channel pre-fader signal is output to the PHONES and MONITOR OUT jacks for monitoring. • MG206C AUX1: Pre-fader AUX2, 3: Pre-fader/post-fader (determined by the AUX PRE switch B) AUX4: Post-fader F 1-2 Switch • MG166CX AUX1: Pre-fader AUX2: Pre-fader/post-fader (determined by the AUX PRE switch B) EFFECT: Post-fader G 3-4 Switch • MG166C AUX1: Pre-fader AUX2: Pre-fader/post-fader (determines by the AUX PRE switch B) AUX3: Post-fader NOTE • To send the signal to the STEREO bus engage the ON switch ( ). • On stereo channels, the L (odd) and R (even) input signals are mixed and sent to the AUX and EFFECT buses. B AUX PRE Switch Selects whether the pre-fader or the post-fader signal is fed to the AUX buses. If the switch is on ( ), the mixer sends the pre-fader signal to the AUX buses, so that AUX outputs are not affected by the channel fader I. If the switch is off ( ) the mixer sends the post-fader signal to the AUX buses. C PAN Control PAN/BAL Control BAL Control The PAN control determines the stereo positioning of the channel signal on the GROUP 1/2 and GROUP 3/4 buses or on the STEREO L/R bus. The BAL control knob sets the balance between left and right channels. Signals input to the L input (odd channel) go to the GROUP 1 or 3 buses or to the STEREO L bus; signals input to the R input (even channel) go to the GROUP 2 or 4 buses or the STEREO R bus. NOTE 14 D ON Switch On channels where this knob provides both PAN and BAL control, the knob operates as a PAN control when input is received via the MIC jack or L (MONO) input only, and as a BAL control when input is received via both L and R inputs. MG206C/MG166CX/MG166C Owner’s Manual This switch assigns the channel’s signal to the GROUP 1/2 bus. NOTE To send the signal to the GROUP 1/2 bus turn the ON switch on ( ). This switch assigns the channel’s signal to the GROUP 3/4 bus. NOTE To send the signal to the GROUP 3/4 bus turn the ON switch on ( ). H ST Switch This switch assigns the channel’s signal to the STEREO L/R bus. NOTE To send the signal to the STEREO bus turn the ON switch on ( ). I Channel Fader Adjusts the level of the channel signal. Use these faders to adjust the balance between the various channels. NOTE Set the fader sliders for unused channels all the way down to minimize noise.  Reference Front & Rear Panels Digital Effects * Only the MG166CX has digital effects. 1 FOOT SWITCH Jack A Yamaha FC5 foot switch (sold separately) can be connected to this jack and used to toggle the digital effects ON and OFF. 1 2 PROGRAM Dial Selects one of the 16 internal effects. See page 19 for details about the internal effects. 3 PARAMETER Control 2 Adjusts the parameter (depth, speed, etc.) for the selected effect. The last value used with each effect type is saved. 3 NOTE 4 When you change to a different effect type, the mixer automatically restores the value that was previously used with that type (regardless of the current position of the PARAMETER knob). These parameter values are reset when the power is turned off. 4 AUX Control Adjusts the level of the signal sent from the internal digital effect unit to the AUX buses. NOTE The signal level sent to the AUX buses is not affected by the EFFECT RTN fader. 5 ON Switch Switches the internal effect on or off. The internal effect is applied only if this switch is turned on. The switch lights orange when on. An optional Yamaha FC5 foot switch (sold separately) can be used to toggle the digital effects ON and OFF. 5 6 7 8 9 NOTE The ON switch lights and the internal effect unit is active when the power is initially turned on. 6 PFL Switch Turn this switch on to send the effect signal to the PFL bus. 7 1-2 Switch 0 This switch assigns the effect signal to the GROUP 1/2 bus. 8 3-4 Switch This switch assigns the effect signal to the GROUP 3/4 bus. 9 ST Switch This switch assigns the effect signal to the STEREO L/R bus. 0 EFFECT RTN Fader Adjusts the signal level sent from the internal digital effect unit to the STEREO bus. MG206C/MG166CX/MG166C Owner’s Manual 15  Reference Front & Rear Panels Master Control Section ● MG206C ● MG166CX/MG166C * 1, C MG166C : EFFECT → AUX3 Rear panel 1 4 6 3 6 1 2 3 4 5 7 8 5 2 8 7 9 0 9 0 A A C C B D B E E H H F I G 16 MG206C/MG166CX/MG166C Owner’s Manual D F I G  Reference Front & Rear Panels 1 SEND Jacks (AUX, EFFECT) These impedance balanced* TRS phone jacks output the signals from the AUX/EFFECT buses. The pre-fader send option should be selected if you are connecting to a monitor system, while the post-fader send option is the best choice when connecting to external signal processors (e.g. effects units). See “AUX, EFFECT Control” on page 14 for information on the types of signals sent by the AUX and EFFECT controls on each mixer model. 2 GROUP OUT (1 to 4) Jacks These impedance-balanced* TRS phone jacks output the GROUP 1/2 and 3/4 signals. Use these jacks to connect to the input jacks of an multi-track recorder, external mixer, or other such device. 8 PHONES Jack Connect a pair of headphones to this TRS phone-type output jack. The PHONES jack outputs the same signal as the MONITOR OUT jacks. 9 PHANTOM +48 V Switch This switch toggles phantom power on and off. When the switch is on the mixer supplies +48V phantom power to all channels that have XLR mic input jacks. Turn this switch on when using one or more phantom-powered condenser microphones. NOTE • Be sure to leave this switch off if you do not need phantom power. 3 REC OUT (L, R) Jacks These RCA pin jacks can be connected to an external recorder such as an MD recorder in order to record the same signal that is being output via the STEREO OUT jacks. NOTE CAUTION The mixer’s STEREO OUT Master fader has no affect on the signal output via these jacks. Be sure to make appropriate level adjustments at the recording device. These RCA pin jacks input a stereo sound source. Use these jacks when you want to connect a CD player directly to the mixer. Select where you want to send the signal using the 2TR IN switch, and adjust the signal level using the 2TR IN control in the Master Control section. 5 RETURN L (MONO), R Jacks These are unbalanced phone-jack type line inputs. The signal received by these jacks can be sent to the STEREO L/R bus as well as the AUX1 and AUX2 buses. When a stereo signal is returned a mono mix of the signal is sent to the AUX1 and AUX2 buses. These jacks are typically used to receive the signal returned from an external effect device (reverb, delay, etc.). NOTE • These jacks can also be used as an auxiliary stereo input. • If you connect to the L (MONO) jack only, the mixer will recognize the signal as monaural and will send the identical signal to both the L and R jacks. 6 STEREO OUT (L, R) Jacks These jacks deliver the mixer’s stereo output. You use these jacks, for example, to connect to the power amplifier driving your main speakers. You can also connect these jacks to a recording device when you wish to record mixer’s stereo output while using the STEREO OUT Master fader I for level control. • XLR jacks XLR-type balanced output jacks. • LINE jacks TRS phone-type balanced output jacks. 7 MONITOR OUT jacks • When turning the switch on, be sure that only condenser microphones are connected to the XLR input jacks. Devices other than condenser mics may be damaged if connected to the phantom power supply. Note, however, that the switch may be left on when connecting to balanced dynamic microphones. • To prevent damage to speakers, be sure to turn off power amplifiers (or powered speakers) before turning this switch on or off. We also recommend that you turn all output controls (STEREO OUT Master fader, GROUP 1-2 fader, GROUP 3-4 fader, etc.) to their minimum settings before operating the switch to avoid the risk of loud noises that could cause hearing loss or device damage. 4 2TR IN Jacks NOTE When this switch is on the mixer supplies DC +48 V power to pins 2 and 3 of all XLR-type MIC INPUT jacks. 0 POWER Indicator This indicator lights when the mixer’s power is ON. A Level Meter This LED meter displays the level of the signal selected by the MONITOR switch D, 2TR IN switch E and PFL switch. The “0” segment corresponds to the nominal output level. The PEAK indicator lights red when the output reaches the clipping level. B RETURN • AUX1, AUX2 Control Adjusts the level at which the L/R signal received at the RETURN jacks (L (MONO) and R) is sent to the AUX1 and AUX2 buses. • STEREO Control Adjusts the level at which the signal received at the RETURN jacks (L (MONO) and R) is sent to the STEREO L/R bus. NOTE • If you supply a signal to the RETURN L (MONO) jack only, the mixer sends the same signal to both the L and R STEREO buses. • (MG206C) Signals input via the RETURN1 jacks are adjusted using the RETURN1 AUX1, AUX2 and the STEREO controls, and signals input via the RETURN2 jacks are adjusted using the RETURN2 AUX1, AUX2 and the STEREO controls. These are impedance-balanced* TRS phone-type output jacks. NOTE The signal output by these jacks is determined by the MONITOR switch, the 2TR IN switch, and the PFL switches on the input channels. * impedance balanced Since the hot and cold terminals of impedance balanced output jacks have the same impedance, these output jacks are less affected by induced noise. MG206C/MG166CX/MG166C Owner’s Manual 17  Reference Front & Rear Panels C Master SEND Controls (AUX, EFFECT) Adjusts the signal level sent to the SEND (AUX, EFFECT) jacks. NOTE If you are using the MG166CX, the Master SEND control (EFFECT) does not affect the level of the signal sent from the EFFECT bus to the internal digital effect processor. D MONITOR/PHONES MONITOR MIX Signal Flow 2TR IN control 2TR IN Playback MONITOR/PHONES controls signal MONITOR STEREO OUT/PHONES bus jacks Recording signal STEREO OUT Master fader REC OUT jacks • MONITOR switches These switches select the signal sent to the MONITOR OUT jacks, PHONES jack and the level meter from STEREO L/R bus, GROUP 1/2 bus or GROUP 3/4 bus. STEREO L/R bus: STEREO ( GROUP 1/2 bus: GROUP ( GROUP 3/4 bus: GROUP ( ) ), 1-2 ( ), 3-4 ( ) ) Controls the level of the signal output to the PHONES jack and the MONITOR OUT jacks. E 2TR IN • 2TR IN Switch If this switch is set to TO MONITOR ( ), the signals input via the 2TR IN jacks are sent to the MONITOR OUT jacks, the PHONES jack, and the level meter. If it is set to TO STEREO ( ), the signals are sent to the STEREO L/R bus. • 2TR IN Control Adjusts the level of the signal sent from the 2TR IN jacks. The following illustration shows how the switch settings correspond to the signal selection. Switches PFL MONITOR/ PHONES 2TR IN ON — — TO STEREO STEREO Signals output via the MONITOR/PHONES jacks PFL STEREO (+ 2TR IN) TO MONITOR STEREO + 2TR IN * TO STEREO 1-2 GROUP 1-2 TO MONITOR GROUP 1-2 (+ 2TR IN) GROUP TO STEREO 3-4 GROUP 3-4 TO MONITOR GROUP 3-4 (+ 2TR IN) * 18 If the input channel PFL switch is on ( ), then only the PFL output from that channel is sent to the MONITOR OUT jacks, PHONES jack, and level meter. F GROUP 1-2 Fader Adjusts the signal level sent to the GROUP OUT 1/2 jacks. G GROUP 3-4 Fader • MONITOR Control OFF NOTE : When overdubbing, you can adjust the levels of the monitor playback signal and the signal being recorded separately. MG206C/MG166CX/MG166C Owner’s Manual Adjust the signal level to the GROUP OUT 3/ 4 jacks. H ST Switch If this switch is on, the signals are sent to the STEREO L/R bus via the GROUP 1-2 fader or GROUP 3-4 fader. The GROUP 1 and 3 signals go to STEREO L and the GROUP 2 and 4 signals go to STEREO R. I STEREO OUT Master Fader Adjusts the signal level sent to the STEREO OUT jacks.  Reference Front & Rear Panels Digital Effect Program List (Only MG166CX) No Program Parameter Description 1 REVERB HALL 1 REVERB TIME 2 REVERB HALL 2 REVERB TIME 3 REVERB ROOM 1 REVERB TIME 4 REVERB ROOM 2 REVERB TIME 5 REVERB STAGE 1 REVERB TIME 6 REVERB STAGE 2 REVERB TIME 7 REVERB PLATE REVERB TIME Simulation of a metal-plate reverb unit, producing a more hard-edged sound. 8 DRUM AMBIENCE REVERB TIME A short reverb that is ideal for use with kick drum. 9 KARAOKE ECHO DELAY TIME Echo designed for karaoke (sing-along) applications. 10 VOCAL ECHO DELAY TIME Echo suitable for vocals. 11 CHORUS 1 LFO Frequency 12 CHORUS 2 LFO Frequency Creates a thick sound by modulating the delay time. The PARAMETER control adjusts the frequency of the LFO* that modulates the delay time. 13 FLANGER LFO Frequency A sweeping pitched effect. The PARAMETER control adjusts the frequency of the LFO* that modulates the delay time. 14 PHASER LFO Frequency Phase modulation produces a cyclical phasing effect. The PARAMETER control adjusts the frequency of the LFO* that modulates the delay time. 15 AUTO WAH LFO Frequency A wah-wah effect with cyclical filter modulation. The PARAMETER control adjusts the frequency of the LFO* that modulates the delay time. 16 DISTORTION DRIVE Adds a sharp-edged distortion to the sound. Reverb simulating a large space such as a concert hall. Reverb simulating the acoustics of a small space (room). Reverb simulating a large stage. * “LFO” stands for Low Frequency Oscillator. An LFO is normally used to modulate another signal, determining the modulation speed and waveform shape. Jack List Input and Output Jacks Polarities Configurations INPUT MIC INPUT, STEREO OUT OUTPUT Pin 1: Ground Pin 2: Hot (+) Pin 3: Cold (–) XLR Jack LINE INPUT (monaural channels) GROUP OUT, STEREO OUT, MONITOR OUT, AUX SEND, EFFECT SEND (Only MG166CX)* Tip: Hot (+) Ring: Cold (–) Sleeve: Ground INSERT Tip: Output Ring: Input Sleeve: Ground PHONES Tip: L Ring: R Sleeve: Ground RETURN LINE INPUT (stereo channels) Tip: Hot Sleeve: Ground Ring Sleeve Tip TRS Phone Jack Sleeve Tip Phone Jack * These jacks will also accept connection to phone plugs. If you use monaural plugs, the connection will be unbalanced. MG206C/MG166CX/MG166C Owner’s Manual 19  Reference Troubleshooting 20 Power doesn’t come on. ❑ Is the supplied power adaptor properly plugged into an appropriate AC wall outlet? ❑ Is the supplied power adaptor properly plugged into the mixer? No sound. ❑ Are microphones, external devices, and speakers connected correctly? ❑ Are the ON switch and ST switch of the channels you are using turned ON? ❑ Are the channel GAIN controls, Channel fader, STEREO OUT Master fader and GROUP 1-2/3-4 fader set to appropriate levels? ❑ Are the MONITOR switch and 2TR IN switch set properly? ❑ Are your speaker cables connected properly, or are they shorted? ❑ If the above checks do not identify the problem, call Yamaha for service. (Refer to the page 71 for a list of service centers.) Sound is faint, distorted, or noisy. ❑ Are the channel GAIN controls, Channel fader, STEREO OUT Master fader and GROUP 1-2/3-4 fader set to appropriate levels? ❑ Are two different instruments connected to the XLR-type and phone jacks, or to the phone and RCA pin jacks on one channel? Please connect to only one of these jacks on each channel. ❑ Is the input signal from the connected device set to an appropriate level? ❑ Are you applying the effects at an appropriate level? ❑ Are microphones connected to the MIC input jacks? ❑ If you are using condenser microphones, is the PHANTOM +48 V switch turned ON? No effect is applied. (If you are using MG166CX) ❑ Check that the EFFECT control on each channel is correctly adjusted. ❑ Be sure that the internal effect unit’s ON switch is turned ON. ❑ Be sure that the EFFECT PARAMETER control and EFFECT RTN fader are correctly adjusted. I want spoken words to be heard more clearly. ❑ Be sure that the switches are ON. ❑ Adjust the equalizers (HIGH, MID and LOW) on each channel. I want to output a monitor signal through speakers. ❑ Connect a powered speaker to the AUX 1, 2 or 3 jack (MG206C), or to the AUX1 or 2 jack (MG166CX/MG166C) and turn the PRE switch on each channel on. Then adjust the output signal by using the AUX controls on each channel and the Master SEND control. The level meter doesn’t show the output signal level. ❑ Are the PFL switches for the channels that you are not using turned on? MG206C/MG166CX/MG166C Owner’s Manual  Reference Specifications MG206C ■ Electrical Specifications Frequency Response Total Harmonic Distortion (THD + N) Hum & Noise STEREO OUT GROUP OUT AUX SEND MONITOR OUT, REC OUT STEREO OUT Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave attenuation. Crosstalk (1 kHz) Maximum voltage gain (1 kHz) All faders and controls are maximum when measured. PAN/BAL: panned hard left or hard right Phantom Voltage CH INPUT 1–12 MIC STEREO OUT GROUP OUT AUX SEND GAIN: min (CHs 1–19/20) 20 Hz–20 kHz Nominal output level @1 kHz Input: CHs 1 to 19/20, RETURN, 2TR IN MIN TYP MAX UNIT -3.0 0.0 1.0 dB 0.1 % +14 dBu @ 20 Hz–20 kHz, Input GAIN Control at minimum EIN (Equivalent Input Noise): Rs = 150 Ω, GAIN: maximum STEREO OUT, GROUP 1-2 fader and GROUP 3-4 fader at nominal level and all channels’ ST and 1-2, 3-4 switches off. Master/AUX control at nominal level and all CH AUX controls at minimum. STEREO OUT STEREO OUT, GROUP 1-2, GROUP 3-4 faders and one CH GROUP OUT fader at nominal level. STEREO OUT Residual Output Noise Adjacent Input CHs 1–12 Input to Output STEREO L/R, CHs 1–12, PAN: panned hard left or right Rs = 150 Ω MIC to CH INSERT OUT INPUT GAIN: maximum MIC to STEREO OUT MIC to GROUP OUT MIC to GROUP to ST MIC to REC OUT MIC to MONITOR OUT, ST TO MONITOR MIC to PHONES OUT MIC to AUX SEND PRE MIC to AUX SEND POST CH 17/18, 19/20 LINE to STEREO OUT CH 17/18, 19/20 LINE to GROUP OUT CH 17/18, 19/20 LINE to AUX SEND PRE CH 17/18, 19/20 LINE to AUX SEND POST Rs = 150 Ω RETURN to STEREO OUT RETURN to AUX SEND Rs = 600 Ω 2TR IN to STEREO OUT MIC no load -128 -88 -81 dBu -64 -98 -70 -70 dB 60 84 94 62.2 94 83 76 86 dB 58 47 57 16 9 27.8 48 V ■ General Specifications Input HPF Input equalization ±15 dB maximum Turn over/roll-off frequency of shelving: 3 dB blow maximum variable level. PEAK Indicator LED Level Meter Power Supply Adaptor Power Consumption Dimensions (W x H x D) Net Weight 80 Hz, 12 dB/oct CHs 1–12 HIGH: 10 kHz (shelving) MID: 250 Hz–5 kHz (peaking) LOW: 100 Hz (shelving) CH 13/14–19/20 HIGH: 10 kHz (shelving) MID: 2.5 kHz (peaking) LOW: 100 Hz (shelving) Red LED turns on when post EQ signal (either post MIC HA or post EQ signal for CHs 13/14–19/20) reaches -3 dB below clipping (+17 dBu). Pre MONITOR Level 2x12 points LED meter (PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB) STEREO/GROUP/PFL bus PEAK lights if the signal level reaches 3 dB below the clipping level. PA-30 AC 35 VCT, 1.4 A, Cable Length = 3.6 m 40 W 478 mm x 102 mm x 496 mm 6.0 kg All faders are nominal if not specified. Output impedance of signal generator: 150 ohms MG206C/MG166CX/MG166C Owner’s Manual 75  Reference Specifications ■ Input Specifications Input Connectors CH INPUT MIC (CHs 1–12) CH INPUT LINE (CHs 1–12) ST CH MIC INPUT (CHs 13/14–19/20) ST CH LINE INPUT (CHs 13/14, 15/16) ST CH INPUT (CHs 17/18, 19/20) Gain Input Impedance Appropriate Impedance 3kΩ 50–600Ω Mics 10kΩ 600Ω Lines 3kΩ 50–600Ω Mics 10kΩ 600Ω Lines 10kΩ 600Ω Lines -60 dB -16 dB -34 dB +10 dB -60 dB -16 dB -34 dB +10 dB -34 dB +10 dB Sensitivity * Nominal Level Max. before Clipping -80 dBu (0.078 mV) -60 dBu (0.775 mV) -40 dBu (7.75 mV) -36 dBu (12.3 mV) -16 dBu (123 mV) +4 dBu (1.23 V) -54 dBu (1.55 mV) -34 dBu (15.5 mV) -14 dBu (155 mV) -10 dBu (245 mV) +10 dBu (2.45 V) +30 dBu (24.5 V) -80 dBu (0.078 mV) -60 dBu (0.775 mV) -40 dBu (7.75 mV) -36 dBu (12.3 mV) -16 dBu (123 mV) -6 dBu (389 mV) -54 dBu (1.55 mV) -34 dBu (15.5 mV) -14 dBu (155 mV) -10 dBu (245 mV) +10 dBu (2.45 V) +30 dBu (24.5 V) -54 dB (1.55 mV) -34 dB (15.5 mV) -14 dB (155 mV) -10 dBu (245 mV) +10 dBu (2.45 V) +30 dBu (24.5 V) Connector Specifications XLR-3-31 type (balanced [1 = GND, 2 = HOT, 3 = COLD]) TRS phone jack (balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) XLR-3-31 type (balanced [1 = GND, 2 = HOT, 3 = COLD]) Phone jack (unbalanced) Phone jack (unbalanced) RCA pin jack CH INSERT IN (CHs 1–12) — 10kΩ 600Ω Lines -20 dBu (77.5 mV) 0 dBu (0.775 V) +20 dBu (7.75 V) TRS phone Jack (unbalanced [Tip = Out, Ring = In, Sleeve = GND]) RETURN (L, R) — 10kΩ 600Ω Lines -12 dBu (195 mV) +4 dBu (1.23 V) +24 dBu (12.3 V) Phone jack (unbalanced) 2TR IN (L, R) — 10kΩ 600Ω Lines -26 dBV (50.1 mV) -10dBV (0.316V) +10dBV (3.16 V) RCA pin jack Where 0 dBu = 0.775 Vrms and 0 dBV= 1 Vrms * Sensitivity : The lowest level that will produce an output of +4 dB (1.23 V), or the nominal output level when the unit is set to the maximum level. (All faders and level controls are at their maximum position.) ■ Output Specifications Output Impedance Appropriate Impedance Nominal Level Max. before clipping Connector Specifications STEREO OUT (L, R) 75Ω 600Ω Lines +4dBu (1.23 V) +24 dBu (12.3 V) XLR-3-32 type (balanced [1 = GND, 2 = HOT, 3 = COLD]) TRS phone jack (balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) GROUP OUT (1–4) 150Ω 10kΩ Lines +4dBu (1.23 V) +20 dBu (7.75 V) TRS phone jack (impedance balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) AUX SEND (1–4) 150Ω 10kΩ Lines +4dBu (1.23 V) +20 dBu (7.75 V) TRS phone jack (impedance balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) CH INSERT OUT (CHs 1–12) 75Ω 10kΩ Lines 0 dBu (0.775 V) +20 dBu (7.75 V) TRS phone jack (unbalanced [Tip = Out, Ring = In, Sleeve = GND]) REC OUT (L, R) 600Ω 10kΩ Lines -10 dBV (0.316 V) +10 dBV (3.16 V) RCA pin jack TRS phone jack (impedance balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) Output Connectors MONITOR OUT (L, R) 150Ω 10kΩ Lines +4 dBu (1.23 V) +20 dBu (7.75 V) PHONES OUT 100Ω 40Ω Phones 3 mW 75 mW Where 0 dBu = 0.775 Vrms and 0 dBV = 1 Vrms 76 MG206C/MG166CX/MG166C Owner’s Manual TRS phone jack  Reference Specifications MG166CX/MG166C ■ Electrical Specifications Frequency Response Total Harmonic Distortion (THD + N) Hum & Noise STEREO OUT GROUP OUT EFFECT/AUX* SEND MONITOR OUT, REC OUT STEREO OUT Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave attenuation. Crosstalk (1 kHz) Maximum voltage gain (1 kHz) All faders and controls are maximum when measured. PAN/BAL: panned hard left or hard right Phantom Voltage CH INPUT 1–8 MIC STEREO OUT GROUP OUT EFFECT/AUX* SEND GAIN: min (CHs 1–11/12) 20 Hz–20 kHz Nominal output level @1 kHz Input: CHs 1 to 15/16, RETURN, 2TR IN MIN TYP MAX UNIT -3.0 0.0 1.0 dB 0.1 % +14 dBu @ 20 Hz–20 kHz, Input GAIN Control at minimum EIN (Equivalent Input Noise): Rs = 150 Ω, GAIN: maximum STEREO OUT, GROUP 1-2 fader and GROUP 3-4 fader at nominal level and all channels’ ST and 1-2, 3-4 switches off. Master EFFECT/AUX* control at nominal level and all CH EFFECT/AUX* controls at minimum. STEREO OUT STEREO OUT, GROUP 1-2, GROUP 3-4 faders and one CH GROUP OUT fader at nominal level. STEREO OUT Residual Output Noise Adjacent Input CHs 1–8 Input to Output STEREO L/R, CHs 1–8, PAN: panned hard left or right Rs = 150 Ω MIC to CH INSERT OUT INPUT GAIN: maximum MIC to STEREO OUT MIC to GROUP OUT MIC to GROUP to ST MIC to REC OUT MIC to MONITOR OUT, ST TO MONITOR MIC to PHONES OUT MIC to AUX SEND PRE MIC to AUX SEND POST, EFFECT* SEND CH 9/10, 11/12 LINE to STEREO OUT CH 9/10, 11/12 LINE to GROUP OUT CH 9/10, 11/12 LINE to AUX SEND PRE CH 9/10, 11/12 LINE to AUX SEND POST, EFFECT* SEND CH 13/14, 15/16 to STEREO OUT CH 13/14, 15/16 to GROUP OUT Rs = 150 Ω RETURN to STEREO OUT RETURN to EFFECT/AUX* SEND Rs = 600 Ω 2TR IN to STEREO OUT MIC no load -128 -88 -81 dBu -64 -98 -70 -70 dB 60 84 94 62.2 94 83 76 86 dB 58 47 57 34 16 9 27.8 48 V ■ General Specifications Input HPF Input equalization ±15 dB maximum Turn over/roll-off frequency of shelving: 3 dB blow maximum variable level. PEAK Indicator Internal Digital Effect (Only MG166CX) LED Level Meter Power Supply Adaptor Power Consumption Dimensions (W x H x D) Net Weight CHs 1–11/12 80 Hz, 12 dB/oct CHs 1–8 HIGH: 10 kHz (shelving) MID: 250 Hz–5 kHz (peaking) LOW: 100 Hz (shelving) CH 9/10–15/16 HIGH: 10 kHz (shelving) MID: 2.5 kHz (peaking) LOW: 100 Hz (shelving) Red LED turns on when post EQ signal (either post MIC HA or post EQ signal for CHs 9/10–15/16) reaches -3 dB below clipping (+17 dBu). 16 PROGRAM, PARAMETER control Foot Switch (Digital Effect On/Off) Pre MONITOR Level 2x12 points LED meter (PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB) STEREO/GROUP/PFL bus PEAK lights if the signal level reaches 3 dB below the clipping level. PA-30 AC 35 VCT, 1.4 A, Cable Length = 3.6 m 35 W (MG166CX), 30 W (MG166C) 478 mm x 102 mm x 496 mm 5.5 kg (MG166CX), 5.3 kg (MG166C) All faders are nominal if not specified. Output impedance of signal generator: 150 ohms * MG166CX: AUX1, 2, EFFECT MG166C: AUX1, 2, 3 MG206C/MG166CX/MG166C Owner’s Manual 77  Reference Specifications ■ Input Specifications Input Connectors Gain 3kΩ 50–600Ω Mics 10kΩ 600Ω Lines 3kΩ 50–600Ω Mics 10kΩ 600Ω Lines -16 dB -34 dB +10 dB -60 dB ST CH MIC INPUT (CHs 9/10, 11/12) ST CH LINE INPUT (CHs 9/10, 11/12) Appropriate Impedance -60 dB CH INPUT MIC (CHs 1–8) CH INPUT LINE (CHs 1–8) Input Impedance -16 dB -34 dB +10 dB Sensitivity * Nominal Level Max. before Clipping -80 dBu (0.078 mV) -60 dBu (0.775 mV) -40 dBu (7.75 mV) -36 dBu (12.3 mV) -16 dBu (123 mV) +4 dBu (1.23 V) -54 dBu (1.55 mV) -34 dBu (15.5 mV) -14 dBu (155 mV) -10 dBu (245 mV) +10 dBu (2.45 V) +30 dBu (24.5 V) -80 dBu (0.078 mV) -60 dBu (0.775 mV) -40 dBu (7.75 mV) -36 dBu (12.3 mV) -16 dBu (123 mV) -6 dBu (389 mV) -54 dBu (1.55 mV) -34 dBu (15.5 mV) -14 dBu (155 mV) -10 dBu (245 mV) +10 dBu (2.45 V) +30 dBu (24.5 V) Connector Specifications XLR-3-31 type (balanced [1 = GND, 2 = HOT, 3 = COLD]) TRS phone jack (balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) XLR-3-31 type (balanced [1 = GND, 2 = HOT, 3 = COLD]) Phone jack (unbalanced) ST CH INPUT (CHs 13/14, 15/16) — 10kΩ 600Ω Lines -30 dBu (24.5 mV) -10 dBu (245 mV) +10 dBu (2.45 V) Phone jack (unbalanced) RCA pin jack CH INSERT IN (CHs 1–8) — 10kΩ 600Ω Lines -20 dBu (77.5 mV) 0 dBu (0.775 V) +20 dBu (7.75 V) TRS phone Jack (unbalanced [Tip = Out, Ring = In, Sleeve = GND]) RETURN (L, R) — 10kΩ 600Ω Lines -12 dBu (195 mV) +4 dBu (1.23 V) +24 dBu (12.3 V) Phone jack (unbalanced) 2TR IN (L, R) — 10kΩ 600Ω Lines -26 dBV (50.1 mV) -10dBV (0.316V) +10dBV (3.16 V) RCA pin jack Where 0 dBu = 0.775 Vrms and 0 dBV= 1 Vrms * Sensitivity : The lowest level that will produce an output of +4 dB (1.23 V), or the nominal output level when the unit is set to the maximum level. (All faders and level controls are at their maximum position.) ■ Output Specifications Output Impedance Appropriate Impedance Nominal Level Max. before clipping Connector Specifications STEREO OUT (L, R) 75Ω 600Ω Lines +4dBu (1.23 V) +24 dBu (12.3 V) XLR-3-32 type (balanced [1 = GND, 2 = HOT, 3 = COLD]) TRS phone jack (balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) GROUP OUT (1–4) 150Ω 10kΩ Lines +4dBu (1.23 V) +20 dBu (7.75 V) TRS phone jack (impedance balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) EFFECT/AUX* SEND 150Ω 10kΩ Lines +4dBu (1.23 V) +20 dBu (7.75 V) TRS phone jack (impedance balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) CH INSERT OUT (CHs 1–8) 75Ω 10kΩ Lines 0 dBu (0.775 V) +20 dBu (7.75 V) TRS phone jack (unbalanced [Tip = Out, Ring = In, Sleeve = GND]) REC OUT (L, R) 600Ω 10kΩ Lines -10 dBV (0.316 V) +10 dBV (3.16 V) RCA pin jack TRS phone jack (impedance balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) Output Connectors MONITOR OUT (L, R) 150Ω 10kΩ Lines +4 dBu (1.23 V) +20 dBu (7.75 V) PHONES OUT 100Ω 40Ω Phones 3 mW 75 mW Where 0 dBu = 0.775 Vrms and 0 dBV= 1 Vrms * MG166CX: AUX1, 2, EFFECT MG166C: AUX1, 2, 3 78 MG206C/MG166CX/MG166C Owner’s Manual TRS phone jack  Reference Specifications ■ Dimensional Diagrams (MG206C/MG166CX/MG166C) 444 102 5 488.5 496 98 478 43 41 Unit: mm ■ Rack Mounting To mount the MG mixer, it requires 12U of rack space. CAUTION If the MG mixer is to be mounted with devices that tend to generate heat, such as power amplifiers, be sure to install ventilation panels to prevent high temperatures from developing inside the mixer. 12U * 12U (Approx. 534mm) * Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. MG206C/MG166CX/MG166C Owner’s Manual 79  (CH1 to 12) [-60 to -16dBu] MG206C/MG166CX/MG166C Owner’s Manual -60dBu -50dBu -40dBu -30dBu -20dBu -10dBu 0dBu +10dBu +20dBu +30dBu (CH17/18, 19/20) ST CH INPUT [6 to 50dB] [-10dBV] [-7.8dBu] 2TR IN R CH IN MIC Gain:Max [-60dBu] CH IN LINE Gain:Max [-34dBu] CH IN MIC Gain:Min [-16dBu] ST CH IN MIC Gain:Max [-60dBu] ST CH IN LINE Gain:Max [-34dBu] ST CH IN MIC Gain:Min [-16dBu] 3-Stage EQ 3-Stage EQ [0dBu] PEAK RE YE [0dBu] YE ON ST CH IN [-10dBu] [-7.8dBu] 2TR IN [-10dBV] RETURN [+4dBu] Clip Level CH Level ST CH Level [Nominal:-10dB] Clip Level [0dBu] [0dBu] [-10dBu] CH Fader [-10dBu] CH Fader ST CH INPUT 17/18-19/20 — Same as ST CH INPUT 13/14-15/16 3-Stage EQ Clip Level [0dBu] ST CH IN LINE Gain:Min [+10dBu] INV INV INV HA L [6 to 50dB] GAIN Trim HA INV Clip Level HPF HA HA [0dBu] TH+GAIN CH9 to 12 GAIN Trim HPF [0dBu] [-34 to +10dBu] HPF HPF [-34 to +10dBu] HPF COMP CH1 to 8 (RETURN1/2) [+4dBu] R RETURN L/MONO [-34 to +10dBu] LINE R [-34 to +10dBu] LINE L HA [-34 to +10dBu] LINE R [-34 to +10dBu] LINE L/MONO HA [16 to 60dB] GAIN Trim CH IN LINE Gain:Min [+10dBu] [-60 to -16dBu] MIC (CH13/14, 15/16) ST CH INPUT [-60 to -16dBu] MIC [0dBu] INSERT I/O [-34 to +10dBu] CH INPUT LINE HPF Hi G [0dBu] Lo G Lo HA Mid f MIC PHANTOM +48V PEAK RE Mid G Mid 80 Hi RE BA BA BA AUX3 ST CH AUX *1 [Nominal:-6dB] CH AUX *1 [Nominal:-6dB] [-6dBu] +15V PRE [0dBu] [-6dBu] [-6dBu] [-6dBu] ST/MONITOR AUX 2 [-14dBu] AUX 1 [-14dBu] [-6dBu] STEREO PFL AUX 4 AUX 3 AUX 2 AUX 1 [-6dBu] G3–4 [0dBu] G1–2 [0dBu] ST PFL [-6dBu] [-6dBu] [-6dBu] AUX2 G3–4 [0dBu] [-6dBu] +15V PRE [0dBu] RETURN 2TR IN [Nominal:-6dB] AUX1 AUX2 AUX3 AUX4 STEREO L STEREO R GROUP 1 GROUP 2 GROUP 3 GROUP 4 PFL L PFL R PFL CTRL AUX1 PRE AUX4 PRE 2TR IN BAL/PAN [0dBu] PAN ST G1–2 [0dBu] SUM [0dBu] SUM SUM [0dBu] [0dBu] [0dBu] AUX SEND *1 [+4dBu] [-10dBu] LED Meter GROUP OUT [+4dBu] GROUP Fader [Nominal:-10dB] DR [0dBu] DR [0dBu] [-16dBu] INV INV MONI/PHONES LED Meter ST Master [Nominal:-10dB] Clip Level REC OUT [-7.8dBu] ST OUT [+4dBu] AUX SEND 2 to 4 — Same as AUX SEND 1 BA SUM SUM BA BA Clip Level MONITOR MIX [-10dBu] ST Fader BA BA BA BA TO STEREO GROUP Fader [-10dBu] GROUP Fader AUX SEND 1 [-6dBu] SUM [0dBu] SUM [0dBu] ST/GROUP Clip Level 1-2/3-4 [0dBu] AUX SEND *1 [Nominal:-6dB] SUM SUM SUM SUM SUM SUM MONI/PHONES [Nominal:-16dB] [-10dBV] REC OUT [+4dBu] [+4dBu] [+4dBu] PHONES [3mW @ 40ohms] -30dBu -20dBu -10dBu 0dBu +10dBu +20dBu +30dBu AUX SEND 1 [3mW,40ohms] PHONES R MONITOR OUT L R [-7.8dBu] L R STEREO OUT L [+4dBu] GROUP OUT MONITOR OUT [+4dBu] Clip Level 4 3 2 1 Reference Specifications ■ Block Diagram and Level Diagram (MG206C) [-6dBu]  [-60 to -16dBu] MG206C/MG166CX/MG166C Owner’s Manual -60dBu -50dBu -40dBu -30dBu -20dBu -10dBu 0dBu +10dBu +20dBu +30dBu (CH9/10, 11/12) L R L R CH IN MIC Gain:Max [-60dBu] CH IN LINE Gain:Max [-34dBu] CH IN MIC Gain:Min [-16dBu] CH IN LINE Gain:Min [+10dBu] FOOT SW EFFECT ON/OFF only MG166CX [-10dBV] [-7.8dBu] 2TR IN [+4dBu] RETURN L/MONO R (CH13/14, 15/16) [-10dBu] ST CH INPUT [-34 to +10dBu] LINE R [-34 to +10dBu] LINE L/MONO [-60 to -16dBu] MIC [0dBu] INSERT I/O [-34 to +10dBu] ST CH INPUT (CH1 to 8) CH INPUT LINE HA HPF [6 to 50dB] GAIN Trim INV INV INV INV HA HA HA HA ST CH IN MIC Gain:Max [-60dBu] ST CH IN LINE Gain:Max [-34dBu] ST CH IN MIC Gain:Min [-16dBu] ST CH IN [-10dBu] Clip Level [0dBu] [0dBu] [0dBu] [0dBu] TH+GAIN CH7 to 8 [0dBu] COMP ST CH IN LINE Gain:Min [+10dBu] Clip Level HPF HPF [-34 to +10dBu] [16 to 60dB] GAIN Trim HA 3-Stage EQ Lo G MIC 3-Stage EQ Hi G CH1 to 6 Mid f 3-Stage EQ 3-Stage EQ Lo YE [0dBu] YE ON [-7.8dBu] 2TR IN [-10dBV] RETURN [+4dBu] IN R out L out [-10dBu] CH Fader [-10dBu] CH Fader DIGITAL EFFECT (DSP) Clip Level YE ON [0dBu] YE CH Level ST CH Level [Nominal:-10dB] Clip Level ON PARAMETER [0dBu] [0dBu] PEAK RE PROGRAM (1–16) 3-Stage EQ Lo HPF Mid G Mid Mid [0dBu] PHANTOM +48V PEAK RE Hi Hi RE BA BA BA +15V PRE ST CH AUX *1 [Nominal:-6dB] CH AUX *1 [Nominal:-6dB] PFL [-10dBu] [0dBu] [-6dBu] [-6dBu] [-6dBu] [-6dBu] AUX 2 [-14dBu] AUX 1 [-14dBu] ST AUX* PFL AUX 2 AUX 1 G3–4 [0dBu] G1–2 [0dBu] ST PFL [-6dBu] [-6dBu] AUX 2 [-14dBu] [-14dBu] [-6dBu] SUM SUM SUM SUM SUM SUM SUM SUM [0dBu] [0dBu] MG166C [-10dBu] BA BA BA SUM SUM BA BA TO ST BA BA BA BA GROUP Fader [Nominal:-10dB] Clip Level LED Meter DR [0dBu] DR [0dBu] ST Master [Nominal:-10dB] GROUP OUT [+4dBu] Clip Level EFFECT AUX 3 AUX * MONITOR MIX AUX SEND* [-6dBu] AUX SEND 2 [-6dBu] MG166CX [-10dBu] GROUP Fader AUX SEND 1 [-6dBu] MODEL [0dBu] [0dBu] [0dBu] SUM [-10dBu] GROUP Fader STEREO Fader [0dBu] SUM [0dBu] STEREO/GROUP [0dBu] AUX SEND *1 [+4dBu] Clip Level SUM SUM SUM 1-2/3-4 [0dBu] AUX SEND *1 [Nominal:-6dB] STEREO L STEREO R GROUP 1 GROUP 2 GROUP 3 GROUP 4 PFL L PFL R PFL CTRL RETURN 2TR IN [Nominal:-6dB] ST [0dBu] G1–2 [0dBu] G3–4 [0dBu] TO ST/TO MONITOR AUX 1 BA BA 2TR IN EFFECT RETURN +15V AUX* [-6dBu] AUX2 +15V PRE [-6dBu] G3–4 [0dBu] G1–2 [0dBu] [0dBu] AUX1 AUX2 AUX* AUX1 Same as CH9/10 BAL/PAN [0dBu] PAN ST INV INV REC OUT [-7.8dBu] ST OUT [+4dBu] [-16dBu] MONI/PHONES LED Meter [3mW,40ohms] [+4dBu] -30dBu -20dBu -10dBu 0dBu +10dBu +20dBu +30dBu [+4dBu] AUX SEND * [+4dBu] AUX SEND 2 PHONES [3mW @ 40ohms] MONI/PHONES [Nominal:-16dB] [+4dBu] PHONES R MONITOR OUT L [-10dBV] [-7.8dBu] REC OUT [+4dBu] AUX SEND 1 R L R STEREO OUT L [+4dBu] GROUP OUT MONITOR OUT [+4dBu] Clip Level 4 3 2 1 Reference Specifications ■ Block Diagram and Level Diagram (MG166CX/MG166C) 81  For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. ASIA POLAND Yamaha Music Central Europe GmbH Sp.z. o.o. Oddzial w Polsce ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 THE NETHERLANDS/ BELGIUM/LUXEMBOURG Yamaha Music Central Europe GmbH, Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 FRANCE CENTRAL & SOUTH AMERICA MEXICO Yamaha de México S.A. de C.V. Calz. Javier Rojo Gómez #1149, Col. Guadalupe del Moral C.P. 09300, México, D.F., México Tel: 55-5804-0600 BRAZIL Yamaha Musical do Brasil Ltda. Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi, CEP 04534-013 Sao Paulo, SP. BRAZIL Tel: 011-3704-1377 ARGENTINA Yamaha Music Latin America, S.A. Sucursal de Argentina Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-4371-7021 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM Yamaha-Kemble Music (U.K.) Ltd. Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England Tel: 01908-366700 GERMANY Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 SWITZERLAND/LIECHTENSTEIN Yamaha Music Central Europe GmbH, Branch Switzerland Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: 01-383 3990 AUSTRIA Yamaha Music Central Europe GmbH, Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 CZECH REPUBLIC/SLOVAKIA/ HUNGARY/SLOVENIA Yamaha Music Central Europe GmbH, Branch Austria, CEE Department Schleiergasse 20, A-1100 Wien, Austria Tel: 01-602039025 Yamaha Musique France BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 ITALY Yamaha Musica Italia S.P.A. Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 SPAIN/PORTUGAL Yamaha-Hazen Música, S.A. Ctra. de la Coruna km. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 SWEDEN Yamaha Scandinavia AB J. A. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. 25/F., United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 INDONESIA PT. Yamaha Music Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 KOREA Yamaha Music Korea Ltd. 8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong, Kangnam-Gu, Seoul, Korea Tel: 080-004-0022 MALAYSIA Yamaha Music Malaysia, Sdn., Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 SINGAPORE Yamaha Music Asia Pte., Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 TAIWAN Yamaha KHS Music Co., Ltd. 3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C. Tel: 02-2511-8688 DENMARK YS Copenhagen Liaison Office Generatorvej 6A DK-2730 Herlev, Denmark Tel: 44 92 49 00 NORWAY Norsk filial av Yamaha Scandinavia AB Grini Næringspark 1 N-1345 Østerås, Norway Tel: 67 16 77 70 OTHER EUROPEAN COUNTRIES Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 THAILAND Siam Music Yamaha Co., Ltd. 891/1 Siam Motors Building, 15-16 floor Rama 1 road, Wangmai, Pathumwan Bangkok 10330, Thailand Tel: 02-215-2626 OTHER ASIAN COUNTRIES Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2317 OCEANIA AFRICA Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2313 MIDDLE EAST TURKEY/CYPRUS Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2313 OTHER COUNTRIES Yamaha Music Gulf FZE LOB 16-513, P.O.Box 17328, Jubel Ali, Dubai, United Arab Emirates Tel: +971-4-881-5868 HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2441 PA17  Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2007 Yamaha Corporation WJ74360 703POAP7.3-01A0 Printed in China