Documenttranscriptie

U CRX-E500 RX-E400 CDC-E500 Receiver/CD Player YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed in Malaysia 0101CRXE500(U).H1-H4.E 1 OWNER’S MANUAL V963100 02.7.9, 4:38 PM SAFETY INSTRUCTIONS 10 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. • 11 Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 12 13 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 14 1 2 3 4 5 6 7 8 9 Read Instructions – All the safety and operating instructions should be read before the product is operated. Retain Instructions – The safety and operating instructions should be retained for future reference. Heed Warnings – All warnings on the product and in the operating instructions should be adhered to. Follow Instructions – All operating and use instructions should be followed. Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 15 16 17 18 19 Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. Grounding or Polarization – This product may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, I CAUTION 0102CRXE500(U).Cau.E 2 02.7.9, 4:40 PM SAFETY INSTRUCTIONS d) 20 21 22 23 If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance - this indicates a need for service. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 24 Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. EXAMPLE OF ANTENNA GROUNDING MAST ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) NEC – NATIONAL ELECTRICAL CODE FCC INFORMATION (for US customers) 1. 2. 3. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. CAUTION II 0102CRXE500(U).Cau.E 3 02.7.9, 4:40 PM CAUTION: READ THIS BEFORE OPERATING THIS UNIT 1 2 3 4 5 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a well ventilated, cool, dry, clean place away from direct sunlight, heat sources, vibration, dust, moisture or cold. In a cabinet, allow about 10 cm (4 in.) of free space all around RX-E400 for adequate ventilation. Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. Do not expose this unit to sudden temperature changes from cold to hot, nor locate this unit in an environment with high humidity (i.e., a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. Avoid installing this unit in a location where foreign objects may fall onto this unit or where this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: • Other components, as they may cause damage and/or discoloration on the surface of this unit. • Burning objects (i.e., candles), as they may cause fire, damage to this unit, and/or personal injury. • Containers with liquid in them, as they may fall, spilling the liquid and causing an electrical shock to the user and/or damage to this unit. 6 7 8 9 10 11 12 13 14 15 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. Do not plug in this unit to a wall outlet until all connections are complete. Do not operate this unit upside-down. It may overheat, possibly causing damage. Do not use excessive force on switches, knobs and/or cords. When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord. Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Use only the voltage specified on this unit. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than as specified. To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm. Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reason. When not planning to use this unit for long periods of time (i.e., vacation), disconnect the AC power plug from the wall outlet. 16 17 18 Be sure to read the “Troubleshooting” section on common operating errors before concluding that this unit is faulty. Before moving this unit, press STANDBY/ON to set the unit in standby mode, then disconnect the AC power plug from the wall outlet. VOLTAGE SELECTOR (General model only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/ 220/240 V AC, 50/60 Hz. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. The unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. CAUTION FOR CARRYING THE UNIT Before carrying the unit, first remove the disc from the unit, press STANDBY/ON to turn the unit off, then disconnect the AC power plug from the wall outlet. FOR CANADIAN CUSTOMERS To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. RX-E400 (U.S.A., Canada and General models) The nameplate is located on the bottom of the unit. IMPORTANT Please record the serial number of this unit in the space below. MODEL: Serial No.: The serial number is located on the buttom of the unit. Retain this Owner’s Manual in a safe place for future reference. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. III CAUTION 0102CRXE500(U).Cau.E 4 02.7.9, 4:40 PM FEATURES <RX-E400> <CDC-E500> • Minimum RMS output power per channel 40 W + 40 W (6Ω, 20 Hz to 20 kHz, 0.1% THD) • Full operation system remote control • 40-Station FM/AM preset tuning • SUBWOOFER output terminal • 3-Disc CD changer • PLAYXCHANGE Disc changing while playing • S-bit DAC and 8fs digital filter • Optical digital output • Random, repeat, and program play • CD TEXT display • CD-RW compatible The receiver (RX-E400) and CD player (CDC-E500) are the main units of the YAMAHA Piano Craft Series. You can upgrade the system by adding the cassette deck (KX-E300) and MD recorder (MDX-E300)*. * MD recorder (MDX-E300) may not be available for some areas. CONTENTS SUPPLIED ACCESSORIES ....................... 2 <CDC-E500> CD PREVENTIVE CARE .......................... 2 NAMES OF BUTTONS AND CONTROLS Front panel ......................................................... 15 Display............................................................... 15 Remote control .................................................. 16 GETTING STARTED Notes on the transportation pad ........................... 3 Remote control .................................................... 4 Connecting the speakers and antennas ................ 5 Connecting the system ......................................... 6 Setting the clock .................................................. 7 Adjusting the brightness of the display ............... 7 <RX-E400> NAMES OF BUTTONS AND CONTROLS Front panel ........................................................... 8 Display ................................................................. 8 Remote control .................................................... 9 BASIC OPERATIONS Listening to a source.......................................... 10 TUNING Listening to the radio ......................................... 11 Presetting stations .............................................. 12 CD OPERATIONS Playing a disc ..................................................... 17 Selecting the time display and CD TEXT ......... 18 Random-sequence play...................................... 19 Repeat play ........................................................ 19 Program play ..................................................... 20 SYSTEM CONTROL Controlling other components ........................... 21 Before recording ................................................ 22 CD synchronized recording ............................... 22 Dubbing setting ................................................. 22 ADDITIONAL INFORMATION Troubleshooting ................................................. 24 Specifications .................................................... 26 USING THE BUILT-IN TIMER Before using the timer ....................................... 13 Timer play and recording .................................. 13 Sleep timer ......................................................... 14 1 0103CRXE500(U).01-02.E 1 02.7.9, 4:40 PM SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained. <RX-E400> • Remote control • AM loop antenna POWER 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A MODE B TEXT/TIME C DISC SKIP D E • Indoor FM antenna TAPE DIRECTION PRESET MD TUNER PRESET CD TAPE AUX MD REC/PAUSE MODE TAPE REC/PAUSE DUBBING SLEEP START <CDC-E500> DISPLAY VOLUME • Audio pin cable • Batteries (AA, R6, UM-3) • System control cable CD PREVENTIVE CARE • This compact disc player is designed for use with following types of disc only. Never attempt to load any other type of disc into the unit. The unit will also play 8-cm (3-inch) compact discs. (Playback only) • Be sure to use only CD-R and CD-RW discs made by reliable manufacturers. • Do not use a CD with tape, seals, or paste on it, because damage to the unit may result. • Do not use any disc that has had its surface printed by a commercially-available label printer. • Compact discs are not affected by small particles of dust or fingerprints on their playing surface, but even so they should be kept clean. Wipe by using a clean, dry cloth. Do not wipe with a circular motion; wipe straight outward from the center. • Some discs cannot be played depending on the disc characteristics or recording conditions (copyrightprotected in a particular way, etc.). • Compact discs are not subjected to wear during play, but damage to the disc surface when the disc is being handled can adversely affect the disc’s play. • Do not use cleaning discs or warped discs. All of these could damage the unit. To prevent a malfunction of this unit • Do not use any non standard shaped CD (heart, etc.) available on the market, because it may damage the unit. • Do not try to clean the disc’s surface by using any type of disc cleaner, record spray, antistatic spray or liquid, or any other chemical-based liquid, because such substances might irreparably damage the disc’s surface. • Do not expose discs to direct sunlight, high temperature or high humidity for a long period of time, because these might warp or otherwise damage the disc. No! 2 0103CRXE500(U).01-02.E 2 02.7.9, 4:40 PM GETTING STARTED Notes on the transportation pad CDC-E500 is shipped with a transportation pad to prevent impact to the internal mechanism that could occur during transportation. Before turning CDC-E500 on, make sure to remove the pad. Before using the unit 1 Take off the caution label. RA NATU 2 L SO UND ACT COMP DISC PLAY ER CDC–E Installing the transportation pad Keep the pad and the caution label, and reattach it as described below whenever the unit is moved. Before attaching it, remove all discs from the disc tray. 1 2 Press DISC 1 , DISC 2 or DISC 3 to open the tray. • When just one disc holder comes out, press DISC SKIP so that two holders come out. Pass the strip of the pad through the hole to bind two disc holders together. 500 Draw the pad out. NATURAL SOUND COMPAC T DISC PLAYER CDC–E50 0 3 Fix the strip on the pad with the caution label. NATURAL SOUND COMPACT DISC PLAYER 4 CDC–E500 Press STANDBY/ON on CDC-E500 to close the disc tray. 3 0104CRXE500(U).03-09.E 3 02.7.9, 4:40 PM GETTING STARTED Remote control Remote control operation range VOLUME NATURAL SOUND This remote control controls a whole system: not only RX-E400 but also CDC-E500. Moreover, a cassette deck (KX-E300) and MD recorder (MDX-E300) that level up your system can be operated by it. Operating buttons for each unit are explained on the pages below: Receiver, RX-E400: CD player, CDC-E500: Cassette deck, KX-E300: MD recorder, MDX-E300: STEREO RECEIVER RX–E400 STANDBY/ON TIMER DISPLAY MEMORY AUTO/MAN'L TIMER ADJ TIMER BASS PRESET/TUNING PRESET/BAND HOUR TREBLE MIN MIN MAX INPUT BALANCE PHONES – p.8 p.15 p.21 p.21 + – + R L Remote control sensor Battery installation Within approximately 6 m (20 feet) 1 30° 3 30° 2 The remote control is shipped with a protection sheet to prevent the surface from being scratched during transportation. When removing the sheet, first put adhesive tape on an edge of the remote control so that the tape sticks to the sheet. Then peel the sheet off with the tape. ER W 3 PO 3 3 3 6 6 6 2 2 9 6 Notes 1 8 7 7 7 7 4 4 8 8 4 4 1 8 5 5 1 1 5 5 • Use only AA, R6, UM-3 batteries for replacement. • Be sure the polarities are correct. (See the illustration inside the battery compartment.) • Remove the batteries if the remote control will not be used for an extended period of time. • If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. Removing the protection sheet 2 If you find that the remote control must be used closer to the main unit than usual, the batteries are weak. Replace batteries with new ones. 9 Battery replacement ER Replace the battery compartment cover. W Insert batteries into the battery compartment. Notes • There should be no large obstacles between the remote control and the main unit. • If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp, etc.), it might cause the remote control not to work correctly. In this case, reposition the main unit to avoid direct lighting. PO Remove the battery compartment cover. 2 1 2 3 Note • Do not scratch the remote control surface when peeling the sheet off. 4 0104CRXE500(U).03-09.E 4 02.7.9, 4:40 PM GETTING STARTED Connecting the speakers and antennas Never plug the AC power cord to the wall outlet until all connections are completed. Follow the steps as shown below to connect the system using the supplied cords and accessories. Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. 3 Right speaker Left speaker FM antenna 2 AM antenna C IN MD OUT FM ANT 75Ω UNBAL. D A R IN L GND TAPE OUT AM ANT B + – IN CD E SUBWOOFER OUT SYSTEM CONNECTOR IN 6Ω MIN./SPEAKER AUX R L SPEAKERS 1 1 Connect the Speakers. 1 Unscrew the knob. 2 Remove approx. 10 mm (4”) of insulation from each of the speaker wires and insert the bare wire into the terminal. 3 Tighten the knob to secure the wire. Red: positive(+) Black: negative(–) 2 1 3 2 Connect the AM loop antenna. Set up the AM loop antenna, then connect it. 4 3 To wall outlet Connect the indoor FM antenna. FM ANT 75 Ω UNBAL 4 Connect the AC power cord to a wall outlet. Notes • Use external FM/AM antennas if you need better reception. Consult your dealer. • The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. To connect the subwoofer (optional) You can reinforce the bass frequencies by adding a subwoofer (optional). Connect the SUBWOOFER OUT terminal of the unit to the INPUT terminal of the subwoofer. GND AM ANT 5 0104CRXE500(U).03-09.E 5 02.7.9, 4:40 PM GETTING STARTED Connecting the system Connecting RX-E400 and CDC-E500 1 2 3 Connect ‰ to ‰ using the Audio pin cable. Insert the plugs into the jacks of the same color. Connect RX-E400 and CDC-E500 with the system control cable. The other SYSTEM CONNECTOR of CDC-E500 is for connecting MDX-E300 or KX-E300. Connect the AC power plug of CDC-E500 to AC OUTLET of RX-E400. This connection reduces the standby power consumption of CDC-E500. C To wall outlet IN MD OUT FM ANT 75Ω UNBAL. D A R IN L GND TAPE OUT AM ANT B + – IN CD E <RX-E400> SUBWOOFER OUT SYSTEM CONNECTOR IN 6Ω MIN./SPEAKER AUX R 1 SPEAKERS L System control cable Audio pin cable 2 To RX-E400 3 ANALOG E L OUT DIGITAL OPTICAL SYSTEM CONNECTOR <CDC-E500> OUT R Adding KX-E300 and MDX-E300 to the above system (For details, refer to the owner's manual supplied with the respective component.) 1 2 3 4 Connect Å and ı of RX-E400 to Å and ı of KX-E300. Connect Ç and Î of RX-E400 to Ç and Î of MDX-E300. Connect an external component to the AUX terminal of RX-E400. Connect DIGITAL OPTICAL OUT of CDC-E500 to DIGITAL OPTICAL IN of MDX-E300. Take off the covers of the optical fiber cable plug, the DIGITAL OPTICAL OUT jack, and the DIGITAL OPTICAL IN jack before making digital connections. Be sure to replace the terminal’s cover when the terminal on the rear panel is not being used, in order to protect from dust. Caution • Never turn RX-E400 on until all connections between components have been completed. • Never connect or disconnect the system control cable and/or power cord while the system components are turned on. 6 0104CRXE500(U).03-09.E 6 02.7.9, 4:40 PM GETTING STARTED Setting the clock You must set the clock before you use the timer functions. The clock is based on a 12-hour system for U.S. and Canada models, and 24-hour system for Australia model. STANDBY/ON HOUR MIN DISPLAY VOLUME NATURAL SOUND STEREO RECEIVER Adjusting the brightness of the display You can adjust the brightness of the display. If you have connected the CD player (CDC-E500), cassette deck (KX-E300), and/or MD recorder (MDX-E300) to this unit, the brightness of the displays is automatically adjusted to that of this unit. RX–E400 DISPLAY STANDBY/ON TIMER DISPLAY MEMORY AUTO/MAN'L TIMER ADJ TIMER PRESET/BAND PRESET/TUNING MIN MAX VOLUME BASS HOUR TREBLE MIN NATURAL SOUND INPUT STEREO RECEIVER RX–E400 BALANCE STANDBY/ON PHONES – + – + L R TIMER DISPLAY MEMORY AUTO/MAN'L TIMER ADJ TIMER BASS PRESET/BAND PRESET/TUNING HOUR TREBLE MIN MIN MAX INPUT BALANCE PHONES TIME ADJ 1 2 3 4 PRESET/BAND – + – + L R Turn on the power by pressing STANDBY/ON on the front panel, or POWER on the remote control. While the power is on, press DISPLAY to display the time. While holding TIME ADJ, press HOUR to set the hour. • If you want to move the time in the reverse direction, press HOUR while holding TIME ADJ and PRESET/BAND. While holding TIME ADJ, press MIN to set the minutes. • If you want to move the time in the reverse direction, press MIN while holding TIME ADJ and PRESET/BAND. INPUT Press and hold DISPLAY for about two seconds so that “Dimmer ±0” appears on the display. While holding DISPLAY, turn INPUT clockwise to increase or counterclockwise to decrease brightness. Control Range: ±0 to –6 (Preset value: ±0) To display the clock Press DISPLAY. The current time appears for about 8 seconds, then the normal display returns. Some buttons and controls may not work while the current time is displayed. Note • In the event of a power failure or when the AC power cord is disconnected for more than five minutes, you must reset the clock. 7 0104CRXE500(U).03-09.E 7 02.7.9, 4:40 PM RX-E400 NAMES OF BUTTONS AND CONTROLS Front panel 1 2 3 45 6 7 8 9 VOLUME NATURAL SOUND STEREO RECEIVER RX–E400 STANDBY/ON DISPLAY TIMER MEMORY AUTO/MAN'L TIMER ADJ TIMER PRESET/TUNING PRESET/BAND HOUR BASS TREBLE MIN MIN MAX INPUT BALANCE PHONES – 0 q + w 1 STANDBY/ON (P.10) 2 TIMER indicator (P.13) 3 DISPLAY (P.13) 4 TIME ADJ (P.7) / MEMORY (P.12) 5 AUTO/MAN’L (P.11) / TIMER (P.13) 6 PRESET/BAND (P.11) 7 Display (This page) 8 PRESET/TUNING / (P.11) HOUR/MIN (P.7/P.13) – + R L e r t 9 VOLUME (P.10) 0 PHONES (P.10) q Remote control sensor (P.4) w BASS (P.10) e TREBLE (P.10) r BALANCE (P.10) t INPUT (P.10) Display PRESET EDIT 1 STEREO AUTO TUNED MEMORY 23 456 7 1 Multi-information display 2 EDIT indicator 3 PRESET indicator (P.12) 4 STEREO indicator (P.11) 5 TUNED indicator (P.11) TIMER SLEEP 8 9 6 AUTO indicator (P.11) 7 MEMORY indicator (P.12) 8 TIMER indicator (P.13) 9 SLEEP indicator (P.14) 8 0104CRXE500(U).03-09.E 8 7/17/02, 3:46 PM RX-E400 NAMES OF BUTTONS AND CONTROLS Remote control 1 POWER (P.10) 2 Preset numbers (P.12) 3 A/B/C/D/E (P.12) 4 PRESET / (P.12) 5 TUNER (RX-E400) (P.12) 6 MD (MDX-E300) (P.21) 7 TAPE (KX-E300) (P.21) 8 CD (CDC-E500) (P.16) 9 AUX (The equipment connected to the AUX terminal) (P.6) 0 SLEEP (P.14) q DISPLAY (P.13) w VOLUME %/fi (P.10) POWER 1 2 3 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A MODE B C TEXT/TIME DISC SKIP D E Note TAPE DIRECTION PRESET 4 6 MD TUNER PRESET CD TAPE AUX MD REC/PAUSE MODE 0 TAPE REC/PAUSE DUBBING SLEEP 5 • 5~9 are operation buttons and input selectors for each component. 7 8 9 START DISPLAY q w VOLUME 9 0104CRXE500(U).03-09.E 9 02.7.9, 4:40 PM BASIC OPERATIONS Listening to a source STANDBY/ON TREBLE 1 2 VOLUME STEREO RECEIVER RX–E400 STANDBY/ON TIMER DISPLAY MEMORY AUTO/MAN'L TIMER ADJ TIMER BASS PRESET/TUNING PRESET/BAND HOUR TREBLE MIN MIN MAX INPUT BALANCE PHONES – PHONES + – + L BASS 3 R BALANCE 4 POWER 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A MODE B TEXT/TIME C DISC SKIP D MD Adjust the volume level by turning VOLUME on the front panel or pressing VOLUME %/fi on the remote control. If desired, adjust BASS, TREBLE, and BALANCE. TREBLE: Turn this control clockwise to increase (or counterclockwise to decrease) the high frequency response. BALANCE: Adjust the balance of the output volume from the left and right speakers to compensate for sound imbalance caused by the speaker location or listening room conditions. PRESET CD Play the source. (Refer to the owner’s manual supplied with each selected component.) BASS: Turn this control clockwise to increase (or counterclockwise to decrease) the low frequency response. TAPE DIRECTION TUNER 5 6 E PRESET Select the desired input source by turning INPUT so that the source appears on the display. • When you operate the component connected to the AUX terminal, turn INPUT to select AUX. INPUT POWER Turn on the power by pressing STANDBY/ON on the front panel, or POWER on the remote control. • Piano Craft series components that have correct system connections made to RX-E400 can be controlled to turn to the on or standby mode by RX-E400. However, once the connected components are turned to the standby mode with their respective STANDBY/ON, they cannot be controlled by RX-E400 STANDBY/ON. VOLUME NATURAL SOUND Set the volume to “MIN” by turning VOLUME. TAPE AUX MD REC/PAUSE MODE TAPE REC/PAUSE DUBBING When you use headphones START SLEEP DISPLAY VOLUME %/fi Connect the headphones to the PHONES jack. You can listen to the sound to be output from the main speakers through the headphones. VOLUME When you have finished using this unit Press STANDBY/ON on the front panel again or POWER on the remote control to set this unit to the standby mode. Auto standby function This unit will be put automatically into the standby mode under the following conditions: • A component connected with a system control cable is selected as an input source. • The component connected to this unit is in stop mode and not operated for 30 minutes. 10 0105CRXE500(U).10-10.E 10 02.7.9, 4:40 PM TUNING Listening to the radio You can find radio stations automatically and manually. AUTO/MAN’L PRESET/TUNING / VOLUME NATURAL SOUND STEREO RECEIVER DISPLAY MEMORY AUTO/MAN'L TIMER ADJ TIMER BASS PRESET/BAND PRESET/TUNING HOUR TREBLE MIN MIN MAX INPUT BALANCE PHONES – + – + L 1 2 3 RX–E400 STANDBY/ON TIMER Manual tuning Follow steps 1 and 2 described in “Automatic tuning.” Press AUTO/MAN’L so that “AUTO” disappears from the display. Press PRESET/TUNING (For a higher (For a lower frequency) to select frequency) or your desired station. • Each time you press PRESET/TUNING or the frequency changes step by step. , R PRESET/BAND INPUT Automatic tuning 1 2 3 4 5 Select TUNER by turning INPUT so that the frequency of a radio station appears in the display. Press PRESET/BAND to select the reception band. Do not select the preset tuning mode (in which “PRESET” appears on the display). Press AUTO/MAN’L so that “AUTO” appears in the display. Press PRESET/TUNING (For a higher (For a lower frequency). frequency) or The unit starts searching for a station. STEREO AUTO TUNED When the unit finds a station, the unit stops searching and “TUNED” appears on the display. 6 If the located station is not the one you want, repeat steps 4 and 5 until a station you want is tuned. Notes • If automatic tuning search does not find the desired station, try manual tuning as described next. • When an FM stereo broadcast with sufficient signal strength is received, “STEREO” appears on the display and you can listen to stereo sound. 11 0106CRXE500(U).11-12.E 11 02.7.9, 4:40 PM TUNING To preset stations automatically Presetting stations The unit can preset station frequencies selected by Automatic tuning or Manual tuning. Up to 40 stations can be stored. With this function, you can select any desired station by pressing the corresponding preset station number. PRESET/TUNING / STEREO RECEIVER Select TUNER as input source by turning INPUT. Press MEMORY for about 2 seconds. • The unit starts presetting stations, “AUTO” and “MEMORY” will flash on the display. Received stations are stored to A1, A2...A8 sequentially. After 40 stations or all FM and AM stations are stored, the display will show the preset station A1. To recall a preset station VOLUME NATURAL SOUND 1 2 RX–E400 STANDBY/ON DISPLAY TIMER MEMORY AUTO/MAN'L TIMER ADJ TIMER BASS PRESET/BAND PRESET/TUNING HOUR TREBLE MIN MIN MAX INPUT BALANCE PHONES – + – + L Press TUNER and select the desired number by pressing PRESET/BAND and PRESET/TUNING / on the front panel or PRESET / , A/B/C/D/E and 1–8 on the remote control. R POWER MEMORY PRESET/BAND INPUT 1–8 To preset stations manually 1 2 3 Tune in a desired station. (Refer to the previous page for the tuning procedure.) A/B/C/D/E Press MEMORY. 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A MODE B TEXT/TIME C DISC SKIP D Within about 5 seconds, use PRESET/TUNING / to select a desired preset number. Continue pressing PRESET/TUNING / to select the group of the preset stations (A, B, C, D, and E). E TAPE DIRECTION PRESET TUNER MD PRESET CD TAPE AUX PRESET STEREO TUNED MD REC/PAUSE MEMORY MODE 4 Press MEMORY. • “MEMORY”, “PRESET”, and preset number will appear on the display. TAPE REC/PAUSE DUBBING SLEEP DISPLAY VOLUME The arrow will appear for a second when it is preset. PRESET STEREO TUNED 5 MEMORY Repeat steps 1 to 4 until all desired stations are preset. Notes • A new setting can be preset in place of a previous one. • The preset stations are retained for a week after you disconnect the AC power cord or a power failure occurs. 12 0106CRXE500(U).11-12.E 12 START 02.7.9, 4:40 PM TUNER PRESET / USING THE BUILT-IN TIMER 3. Timer REC Select the recording component by turning INPUT. If you like to enjoy timer play with TUNER or AUX, select “REC Mode OFF”. Before using the timer If you want to use the cassette deck, KX-E300 or the MD Recorder, MDX-E300 for timer play or recording, you must first make the connections as shown in “Connecting the system” on page 6. For details, refer to the instructions supplied with the MDX-E300 or KX-E300. (Example) Timer play and recording 4. ON Time “ON Time” appears on the display for a second, and changed to the time setting mode. Press HOUR to set the hour. Press MIN to set the minute. By using the built-in timer, you can have the unit turn on at a specified time and begin playing or recording automatically. You can also specify the turn off time. HOUR MIN DISPLAY VOLUME NATURAL SOUND STEREO RECEIVER RX–E400 5. OFF Time Set the time the same way as above. If you set the ON time but not OFF time, the timer play or recording will finish automatically after an hour. STANDBY/ON TIMER DISPLAY MEMORY AUTO/MAN'L TIMER ADJ TIMER BASS PRESET/BAND PRESET/TUNING HOUR TREBLE MIN MIN MAX INPUT BALANCE PHONES – + – + TIMER 1 L Notes R • The display mode will change in about 8 seconds. If the mode is changed before the setting is completed, call the mode again by pressing DISPLAY once or more. • If you select the input other than TUNER and AUX on “2. Timer Input”, “3. Timer REC” is skipped. INPUT Press DISPLAY. Whenever DISPLAY is pressed, the display mode changes as follows: 1. Clock Time (TIMER on/off mode) If you have not set the clock yet “Set Clock” appears. You need to set the current time as described on page 7. 2. Timer Input Select the source to be played by turning INPUT. • Timer recording is possible only when you select TUNER or AUX. 2 Press TIMER to complete the timer setting. The system is put in the standby mode. • TIMER indicator lights up. If you continue using the system, press STANDBY/ ON to turn on this unit. To cancel the timer play setting Press DISPLAY to show the current time, then press TIMER so that “TIMER” goes off from the display. You can also cancel by pressing TIMER in standby mode. Note • In the event of a power failure or when the AC power cord is disconnected for more than five minutes, you must reset the clock. 13 0107CRXE500(U).13-14.E 13 02.7.9, 4:40 PM USING THE BUILT-IN TIMER Sleep timer The unit can be turned off automatically at a selected SLEEP time. PRESET MD TUNER PRESET CD TAPE AUX MD REC/PAUSE MODE SLEEP TAPE REC/PAUSE DUBBING START SLEEP DISPLAY VOLUME 1 2 Play the desired sound source. Press SLEEP repeatedly until the desired sleep time appears in the display. Each time you press SLEEP, the sleep time changes as follows: SLEEP 2h00m SLEEP 1h30m SLEEP 1h00m SLEEP 0h30m SLEEP OFF About 4 seconds after setting, the normal display will resume. • “SLEEP” will appear in the display. 3 The unit will turn off automatically when the selected sleep time is reached. 14 0107CRXE500(U).13-14.E 14 02.7.9, 4:40 PM CDC-E500 NAMES OF BUTTONS AND CONTROLS Front panel 1 2 3 NATURAL SOUND 4 COMPACT DISC PLAYER 5 CDC-E500 DISC 1 DISC 2 DISC 3 DISC SKIP STANDBY/ON 6 7 8 1 STANDBY/ON 2 Display (this page) 3 Disc tray (P.17) 4 DISC SKIP (P.18) 5 DISC 1/2/3 (Open/Close) (P.17) 6 & (Stop) (P.17) 7 ^ (Play/Pause) (P.17) 8 $/! (Skip/Search Backward) ⁄/› (Skip/Search Forward) (P.17) Display 1 1 2 2 3 4 5 6 REP PROG RANDOM CD–TEXT 3 1DISC 3DISCS S F TITLE ARTIST TRACK 7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 OOOOOOOOOOOO 9 8 1 Disc indicator 2 1 DISC/3 DISCS (Disc play mode) indicator 3 REP S/F (Single or Full) indicator (P.19) 4 PROG indicator (P.20) 5 RANDOM indicator (P.19) 6 CD-TEXT indicator (P.18) 0 7 Music calendar 8 Multi-information display 9 * (Pause) indicator 0 ‹ (Play) indicator 15 0108CRXE500(U).15-16.E 15 02.7.9, 4:40 PM CDC-E500 NAMES OF BUTTONS AND CONTROLS Remote control POWER 1 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A MODE B TEXT/TIME C DISC SKIP 2 3 5 6 9 0 D 4 7 E 8 q TAPE DIRECTION PRESET MD TUNER PRESET CD TAPE w AUX MD REC/PAUSE MODE 1 Numeric buttons (P.17) • +100 button is used when operating MDX-E300. 2 REP (Repeat) (P.19) 3 RANDOM (Random) (P.19) 4 PROG (Program) (P.20) 5 MODE (P.19) 6 TEXT/TIME (P.18) 7 DISC SKIP (P.18) 8 ^ (Play/Pause) (P.17) 9 & (Stop) (P.17) 0 $ ! (Skip/Search Backward) (P.17) q ⁄ › (Skip/Search Forward) (P.17) w CD input (P.17) TAPE REC/PAUSE DUBBING SLEEP START DISPLAY VOLUME 16 0108CRXE500(U).15-16.E 16 02.7.9, 4:40 PM CD OPERATIONS 3 Playing a disc Press DISC 1 , DISC 2 or DISC 3 the disc tray, and place a CD on the tray. to open DISC SKIP $/! ⁄/› DISC NATURAL SOUND COMPACT DISC PLAYER CDC-E500 RAL NATU ER PLAY E500 CDC– PACT D COM SOUN DISC 1 DISC 2 DISC 3 DISC SKIP STANDBY/ON 4 & ^ 5 Press the selected disc’s DISC button to close the disc tray. To insert other CDs, follow the same procedure. Press ^ to start play. This unit starts play. POWER To pause play Numeric buttons 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A MODE B TEXT/TIME C DISC SKIP Press ^. To resume play, press ^ again. To stop play Press &. To eject the CD MODE D DISC SKIP E ^ & $ !/⁄ › Direct play MD TUNER PRESET CD CD TAPE AUX MD REC/PAUSE MODE TAPE REC/PAUSE DUBBING SLEEP START DISPLAY VOLUME 2 To play a specific track on the disc (Skip) TAPE DIRECTION PRESET 1 Press to open the disc tray, and remove the CD from the tray. Select a desired track using the numeric button. (Example: To select 35, press +10 three times so that “3 –” appears in the display, then press 5.) Skip play Press ⁄/› to skip forward or $/! to skip backward. Press once for each track to be skipped. Notes • You cannot enter a number that is higher than the last track number on the selected disc. • These operations can also be performed when the unit is in the pause or stop mode. • During stop mode, if ⁄/› or $/! is pressed, the track number successively changes to higher numbers (or lower numbers). Turn on the power of RX-E400 and CDC-E500. (Refer to page 10.) To advance or reverse playback rapidly (Search) Press CD on the remote control in order to operate the CD player by the remote control. Press and hold ⁄/› to advance playback rapidly, and $/! to reverse playback rapidly. Note • This unit cannot play a CD-R or CD-RW disc unless the disc is finalized. Please make sure to finalize the disc on the CD recorder before playing on this unit. 17 0109CRXE500(U).17-20.E 17 02.7.9, 4:40 PM CD OPERATIONS To change the disc play mode Selecting the time display and CD TEXT If necessary, change the disc play mode by pressing MODE on the remote control. All disc play mode: All disc on the disc tray are played sequentially. You can select any of four time displays by pressing TEXT/TIME. When you play a CD with CD TEXT, the disc title, artist name, and track name are also displayed. POWER 3DISCS Single disc play mode: Only the designated disc is played. 1DISC To select another disc Press DISC SKIP once or more. The circle around the selected disc number lights up. (Example) When the disc 2 is selected. 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A MODE B TEXT/TIME C DISC SKIP D TEXT/TIME E Each time you press TEXT/TIME the display changes as follows: The current track number 1 2 3 3 4 5 6 7 1 2 3 3DISCS 03 To exchange a disc (or discs) while playing (PLAYXCHANGE) 3:53 3 4 5 6 7 1 2 3 3DISCS 03 You can open the disc tray without interrupting play by pressing one of DISC 1/2/3 (not the currently playing one). -2:22 3 4 5 6 7 1 2 3 3DISCS 03(T) 50:33 3 4 5 6 7 1 2 3 3DISCS 03(T) -33:00 Elapsed time of the current track Remaining time of the current track Total disc play time Total remaining time of the disc • “CD-TEXT” appears on the display if a CD has CD TEXT. Disc title Artist name Track name Note • The disc title, artist names, or track names may not be displayed with some CD TEXT discs. In this case, “(NO ENTRY)” appears on the display for about two seconds and then go back to the time display. 18 0109CRXE500(U).17-20.E 18 02.7.9, 4:41 PM CD OPERATIONS Random-sequence play The unit can play all the tracks in a random sequence. Repeat play You can play any desired track or disc repeatedly. Press REP to select the repeat mode. POWER POWER MODE 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A MODE B TEXT/TIME C DISC SKIP D E RANDOM DISC SKIP REP 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A MODE B TEXT/TIME C DISC SKIP D 1 2 If necessary, switch the disc play mode by pressing MODE. • If the single disc play mode is selected, select the desired disc by pressing DISC SKIP. Press RANDOM. • “RANDOM” appears on the display. The unit starts random sequence play. To cancel random-sequence play mode Press & or RANDOM. • “RANDOM” disappears from the display. E SINGLE REPEAT The current track is played repeatedly. REP S FULL REPEAT When the CD player is in the single disc play mode: The designated disc is played repeatedly. When the CD player is in the all disc play mode: All discs on the disc tray are played repeatedly. REP F Notes • This feature will not function during programming, or during programmed play. • If ⁄/› is pressed during random-sequence play, the next randomly programmed track will be played. If $/! is pressed, play will return to the beginning of the current track. • Total remaining time on the disc will not be displayed during random-sequence play. • In random-sequence play mode, all randomly sequenced tracks are played repeatedly in the same order. To cancel repeat play mode Press REP successively until “REP S” and “REP F” disappear from the display. 19 0109CRXE500(U).17-20.E 19 7/17/02, 3:58 PM CD OPERATIONS Program play 4 • The selected track number and the total play time of the programmed tracks appear on the display, and it will soon be replaced by the display of the next play order. Programmed track numbers on the selected disc will stop flashing and light up on the music calendar. • Pressing TEXT/TIME displays the total play time of the programmed tracks for about one second, and then it is replaced by the display of the next play order. When you program tracks of different discs, total play time does not include the time that takes to change discs. By creating a program, you can enjoy listening to your favourite tracks in any desired order. As many as 30 tracks can be programmed in sequence. POWER Numeric buttons TEXT/TIME ^ 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A MODE B TEXT/TIME C DISC SKIP D PROG DISC SKIP E Use the numeric buttons to select a track number. 5 6 Repeat steps 3 and 4 to program more tracks. You can select the same track again. Press ^ to start program play. & $ !/⁄ › To stop program play mode TAPE DIRECTION PRESET TUNER MD Press &. PRESET CD TAPE AUX MD REC/PAUSE Note • ⁄/› or $/! can be used during program play to skip to tracks within the program. TAPE REC/PAUSE To check program data MODE DUBBING SLEEP START DISPLAY VOLUME 1. Press & while the disc is playing to stop program play. 2. Press PROG. Then each time you press ⁄/› / $/!, the track number and the program number are displayed in the order of the program. To change program data 1 2 Press & to stop the unit. 1. Follow the preceding procedure described in “To check program data.” Press PROG. • “PROG” and “P-01” light up on the display, and all track numbers on the selected disc start flashing. 2. Display the track number to be changed by pressing ⁄/› / $/!. 3. Press the numeric button of the desired track. The previously programmed track will be cleared from memory and the new one will be programmed. 1 2 3 3DISCS PROG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 P-01 3 If necessary, select the desired disc by pressing DISC SKIP. • Just after you change the disc, the CD player reads the contents of the newly selected disc for a few seconds. If you go on to the next step during this internal operation, “WAIT” appears on the display and your operation is canceled. To delete all program data When program play is stopped, press &. Note • Turning the unit to the standby mode or opening the disc tray also deletes the program data. 20 0109CRXE500(U).17-20.E 20 7/17/02, 3:58 PM SYSTEM CONTROL Controlling other components MDX-E300 POWER 1 2 3 4 1 2 3 1 4 2 5 3 6 4 7 5 8 6 9 7 0 8 +10 +100 REP RANDOM PROG A B TEXT/TIME C DISC SKIP MODE D E 6,1 8,3 9,4 7,2 TAPE DIRECTION PRESET 0 5 MD KX-E300 TUNER PRESET CD TAPE 5 AUX q 1 Numeric buttons 2 REP (Repeat) 3 RANDOM 4 TEXT/TIME 5 PROG (Program) 6 ^ (Play/Pause) 7 ⁄ › (Skip/Search Forward) 8 $ ! (Skip/Search Backward) 9 & (Stop) 0 MD input q MD REC/PAUSE MD REC/PAUSE MODE TAPE REC/PAUSE DUBBING SLEEP 6 1 ^ (Play) 2 ⁄ › (Fast-forward) 3 $ ! (Rewind) 4 & (Stop) 5 TAPE input 6 TAPE REC/PAUSE START DISPLAY VOLUME 21 0110CRXE500(U).21-23.E 21 02.7.9, 4:41 PM SYSTEM CONTROL Before recording Dubbing setting When you record by using MDX-E300 or KX-E300, you must first make the connections as shown in “Connecting the system” on page 6. For details, refer to the instructions supplied with the MDX-E300 or KX-E300. A source from the component which is connected to the AUX terminal component can be recorded on a tape or MD. There are six different combinations of components. Once you choose a certain mode, recording starts and ends automatically in a certain way for each mode. AUX MD REC/PAUSE DUBBING MODE CD synchronized recording MODE TAPE REC/PAUSE DUBBING SLEEP START DISPLAY DUBBING START VOLUME You can start and stop recording a CD on a MD or a tape by pressing just one button. D E ^ & MD MD REC/PAUSE TUNER PRESET CD CD TAPE AUX MD REC/PAUSE MODE TAPE REC/PAUSE DUBBING SLEEP START TAPE REC/PAUSE DISPLAY VOLUME 1 2 3 Decide the combination of the components. Each time you press DUBBING MODE, the mode will change in the below order. 1 TAPE DIRECTION PRESET 1 • Recording automatically starts from the beginning of the tape. (By pressing DUBBING START, the tape automatically rewinds to the beginning if it is in the middle.) • When the recording on side A finishes while a track is being played back, the recording on side B starts from the beginning of the same track. • The sound is automatically faded out when it gets close to the end of side B. Press CD. Press MD REC/PAUSE to record on a MD or TAPE REC/PAUSE to record on a tape. 2 Press ^. Recording starts automatically on MDX-E300 or KX-E300. To stop recording Press &. • Pressing & on CDC-E500 stops CD play and turn the recording component into “REC standby” mode. • Pressing & on MDX-E300 or KX-E300 stops recording, while the CD player keeps on playing. 3 Play unit Note • Recording does not pause while CDC-E500 changes discs. When recording the tracks of different discs, it is recommended to set the CD player to single disc play mode and record the discs individually. When recording the programmed sequence of the tracks of different discs, make sure that the length of the MD or the tape is longer than the total play time of the programmed tracks, so that it is enough to cover the time for changing discs. • Same as CD = TAPE 22 0110CRXE500(U).21-23.E 22 02.7.9, 4:41 PM Record unit SYSTEM CONTROL 4 Play unit Record unit • Recording automatically starts at the beginning of the tape. (By pressing DUBBING START, the tape automatically rewinds to the beginning if it is in the middle.) 2 Press DUBBING START to start recording. Note • The displays 1~4 which include the component you have not connected to your receiver (RX-E400) will be skipped. • Recording does not pause while CDC-E500 changes discs. When recording the tracks of different discs, it is recommended to set the CD player to single disc play mode and record the discs individually. When recording the programmed sequence of the tracks of different discs, make sure that the length of the MD or the tape is longer than the total play time of the programmed tracks, so that it is enough to cover the time for changing discs. To stop dubbing Press &. 23 0110CRXE500(U).21-23.E 23 02.7.9, 4:41 PM ADDITIONAL INFORMATION Troubleshooting If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. When taking the service, the MDX-E300 or KX-E300 may be needed. For details, contact your authorized YAMAHA dealer or service center. RX-E400 RECEIVER SYMPTOM CAUSE REMEDY The unit does not switch ON when the STANDBY/ON is pressed. The AC power cord is not connected or not completely connected. Securely connect the power cord. No sound from one speaker. Loose speaker connections. Connect properly. The sound suddenly goes off. The protection circuit has been activated because of a short circuit, etc. Check the speaker wires are not touching each other and then turn the unit back on. No sound from an external unit connected with this unit or play does not begin. Incorrect cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Input source selection is not proper. Make a proper input source selection. Sound distorted. The component connected to this unit is disconnected from AC outlet. Connect the AC power cord of the component to an AC outlet. Excessive static in FM broadcasts. Interference from starting motor of a nearby car. Position the FM antenna as high and as far away from nearby roads as possible. Connect using a coaxial cable. Interference from the thermostat of a nearby electrical appliance. Noise increases during stereo broadcasts. Antenna input is too weak due to obstructions or excessive distance from the broadcasting station. Check the antenna connection. Stereo broadcasts are noisy and STEREO indicator blinks on and off. Insufficient antenna input. Install an antenna appropriate for the electric field strength of your area. Cannot select preset stations. Preset memory has been erased. Reprogram memory presets. Buzzing or static during AM broadcasts. Interference from sources such as lightning, fluorescent lights, electric motors or thermostat of nearby electrical appliance. The problem is difficult to eliminate, but can be lessened by grounding AM loop antenna. TV or microprocessor is being used nearby. Move away from TV or microprocessor. Radio signal is weak or the antenna is not properly connected. Properly connect the AM loop antenna. AM broadcast sensitivity is poor. Install a multi-element type FM antenna if possible. Change orientation of the AM loop antenna. Install an external AM loop antenna. Cannot set timer. Current time is not set. Set current time. The unit does not work normally. The internal microcomputer has been frozen by an external electric shock (lightning, excessive static electricity, etc.) or the power supply with low voltage. Unplug the AC power cord from the wall outlet, and then plug in again after about one minute. 24 0111CRXE500(U).24-27.E 24 02.7.9, 4:41 PM REMOTE CONTROL CDC-E500 CD PLAYER ADDITIONAL INFORMATION SYMPTOM CAUSE REMEDY Play does not begin. The disc is damaged. Check the disc carefully; replace it if necessary. There is moisture on the laser pick-up. Wait 20 to 30 minutes after switching the unit ON before trying to play a disc. The disc has been loaded upside down. Reload the disc with the label side facing up. The disc is dirty. Clean the disc. Play is delayed, or begins at the wrong place. The disc may be scratched or damaged. Check the disc carefully; replace it if necessary. CD synchronized recording or Automatic recording function does not work. The system cable is not connected securely. Connect the system cable properly. Sound “skips.” The unit is being subjected to vibrations or impacts. Relocate the unit. The disc is dirty. Clean the disc. Sound “hums.” Improper cable connections. Securely connect the audio cables. If the problem persists, the cables may be defective. Noise from inside of the unit. The disc may be warped. Replace the disc. The remote control does not work. The batteries of the remote control are too weak. Replace the batteries with new ones. Remote control is too far away or is being used at an incorrect angle. Use within 6 meters and 60 degree radius. Direct sunlight or lighting (of an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of the unit. Change the position of the unit. Remote control is being used near TV set with a remote control sensor. Relocate this unit away from the TV or cover the TV’s remote control sensor. TV functions strangely when the remote control is being used. 25 0111CRXE500(U).24-27.E 25 02.7.9, 4:41 PM ADDITIONAL INFORMATION Specifications <RX-E400> <CDC-E500> Amplifier section CD player section Minimum RMS output power per channel ................................................ 55 W + 55 W (6Ω 1kHz 0.1% THD) .............................. 40 W + 40 W (6Ω 20 Hz to 20 kHz 0.1% THD) DIN Standard output power per channel (Europe model) ................................................ 60 W + 60 W (4Ω 1kHz 0.7% THD) Input sensitivity/Impedance CD/TAPE/MD/AUX ................................................. 150 mV/47 kΩ Frequency response CD etc. ..................................................... 20 Hz to 20 kHz, ±0.5 dB Total Harmonic Distortion (20 Hz to 20 kHz) CD etc. 20 W, 6 Ω ................................................................... 0.04% Signal-to-Noise ratio (IHF-A Network) CD etc. (250 mV, Input shorted) ............................................. 98 dB Output level/Impedance PHONES ..................................................................... 0.43 V/330 Ω D/A converter ...................................................................... S-bit DAC Frequency response ...................................... 2 Hz to 20 kHz, ±0.5 dB S/N ratio ................................................................................... 102 dB Tuner section Tuning range FM [U.S.A. and Canada models] ................................ 87.5 – 107.9 MHz [U.K., Europe, Australia and General models] .......................................................................... 87.50 – 108.00 MHz AM [U.S.A. and Canada models] ................................... 530 – 1710 kHz [U.K., Europe and Australia models] ...................... 531 – 1611 kHz [General model] ....................................... 530/531 – 1710/1611 kHz Sensitivity FM (S/N 30dB) ....................................................................... 1.0 µV AM .................................................................................... 300 µV/m Laser diode properties • • • • Material: GaAIAs Wavelength: 780 nm Emission duration: continuous Laser output: max. 44.6 µW* * This output is the value measured at a distance of about 200 mm from the objective lens surface on the Optical Pick-up Block. General Power supply [U.S.A. and Canada models] ................................. AC 120 V, 60 Hz [Australia model] ................................................... AC 240 V, 50 Hz Power consumption ..................................................................... 13 W Power consumption (standby mode) ......................................... 3.8 W Dimensions (W x H x D) ..................................... 217 x 108 x 347 mm Weight ........................................................................................ 3.5 kg Specifications are subject to change without notice. General Power supply [U.S.A. and Canada models] ................................. AC 120 V, 60 Hz [Australia model] ................................................... AC 240 V, 50 Hz [U.K. and Europe models] ..................................... AC 230 V, 50 Hz [General model] .......................... AC 110/120/220/240 V, 50/60 Hz Power consumption [U.S.A. and Canada models] .................................................. 110 W [U.K., Europe, Australia and General models] ...................... 125 W Power consumption (standby mode) [U.S.A. and Canada models] ................................................... 0.7 W [U.K., Europe and Australia models] ...................................... 0.8 W Dimensions (W x H x D) .................................. 217 x 108 x 372 mm Weight ..................................................................................... 5.4 kg 26 0111CRXE500(U).24-27.E 26 02.7.9, 4:41 PM U CRX-E500 RX-E400 CDC-E500 Receiver/CD Player YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed in Malaysia 0101CRXE500(U).H1-H4.E 1 OWNER’S MANUAL V963100 02.7.9, 4:38 PM