Documenttranscriptie

BASS AMPLIFIER BBT500-115 BBT500-110 Owner’s Manual Mode d’emploi Bedienungsanleitung Manual del Usuario Manuale di Istruzioni Handleiding BBT500-115 BBT500-110  FCC INFORMATION (U.S.A.) tions does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regula* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. CANADA This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB003 du Canada. • This applies only to products distributed by Yamaha Canada Music Ltd. • Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée. IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN-and-YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. • This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. 2  IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 Only use attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. ON THE TOP OF THIS UNIT, DO NOT PLACE: CONTAINERS WITH LIQUID IN THEM, AS THEY MAY FALL AND LIQUID MAY CAUSE ELECTRICAL SHOCK TO THE USER AND/OR DAMAGE TO THIS UNIT. 3  SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following: Warning: Do not attempt to recharge, disassemble, or incinerate this type of battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by applicable laws. Note: In some areas, the servicer is required by law to return the defective parts. However, you do have the option of having the servicer dispose of these parts for you. See rear of Amplifier for graphic symbol markings. Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. NOTICE: Service charges incurred due to lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service. The lightning flash with arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock. NAME PLATE LOCATION: The graphic below indicates the location of the name plate. Information such as model number, power requirements, serial number, etc., can be found at this location. You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase. IMPORTANT NOTICE: All Yamaha electronic products are tested and approved by an independent safety testing laboratory in order that you may be sure that when it is properly installed and used in its normal and customary manner, all foreseeable risks have been eliminated. DO NOT modify this unit or commission others to do so unless specifically authorized by Yamaha. Product performance and/or safety standards may be diminished. Claims filed under the expressed warranty may be denied if the unit is/has been modified. Implied warranties may also be affected. SPECIFICATIONS SUBJECT TO CHANGE: The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units. Model Serial No. 92-469-① (rear) 4 Purchase Date  Precautions ● Avoid using your amplifier and speaker in the following locations to prevent possible damage: • In direct sunlight or next to heating equipment. • Extremely cold or hot locations. • Locations exposed to high humidity or excessive dust. • Locations subject to strong shocks or vibration. ● Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: • Other components, as they may cause damage and/or discoloration on the surface of this unit. • Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. • Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit. ● If one of the following occurs, disconnect the cable from the INPUT jack as soon as possible then contact the dealer from whom you purchased the device for repair. • The speaker cable or plug has become damaged. • Sound is not produced or an abnormal smell or smoke is present. • A foreign substance gets into the device or liquid is spilled onto the device. • The device is wet or damp (rain, etc.). • An abnormality or damage is found on the device. ● Before making any connections, make sure that the power on the amplifier and any external devices is switched OFF. ● To protect the speaker from possible damage, always set the OUTPUT knob to “0” before switching the power ON/OFF. ● When connecting the speaker jack to a speaker, use only a cable designed specifically for connecting a speaker to the amplifier. The use of any other cable can result in fire. ● Even if the device’s main power switch is switched OFF, power is not cut off from the device. Place the device close to an easily accessible electric outlet so it can be plugged in or unplugged with ease. ● Your Yamaha amplifier is a precision musical instrument. Handle it with care and avoid dropping or bumping it. ● Do not apply excessive force to the switches and controls. ● To prevent damage and possibly electrical shock, never open the case and tamper with the internal circuitry. ● Do not block the ventilation ducts. The device is designed with ducts on the front and back to prevent temperatures from rising inside the device. Blocking the ducts will cause heat to buildup inside the device, which may result in fire. ● Never place the device on an unstable surface, table, or sloped surface. Also, never stack the device excessively. Doing so may cause the device to fall or overturn, causing injury. ● Keep the amplifier away from neon signs or fluorescent lighting to prevent noise pickup. ● Never use benzene, thinner or other volatile liquids for cleaning, as these chemicals may cause damage or discoloration to the finish. Always use a dry, soft cloth to wipe off dust and dirt. To protect your speakers The following may cause damage to speakers: • Feedback caused when using a microphone. • Continuous high sound pressure level produced by electronic instruments. • Continuous high-power output distorted signals. • Popping noises caused by turning on equipment, or by connecting or disconnecting system-components while the amplifier is turned on. Operating Cautions! To use in a safe manner, please obey the following ● About the XLR jack’s polarity The pin order of the XLR type connector is as follows: 1: Shield (GND), 2: Hot (+), 3: Cold (-) This conforms to the IEC60268 standard. ● About Cellular Phone Interference Cellular phones used in close proximity to the device may cause noise. If this is the case, move the phone a little away from the device. CAUTION! Attaching and removing the casters (BBT500-115 only) When attaching the supplied casters, make sure that the caster’s shaft is inserted all the way into the receptacle on the bottom of the cabinet. Also, make sure that all four casters are attached to ensure stability. Using the cabinet with loose or poorly attached casters will result in a condition that is unstable and hazardous, and cause the cabinet to fall over, etc. Wrong! OK * If the device is to be stacked, we recommend that the casters be removed from the amplifier/speaker to prevent overturning. ● During thunderstorms, switch off the power as soon as possible and unplug the device from the electric outlet. If there are lightning strikes, do not touch the power cable if it is still connected to the electric outlet. Doing so can result in electric shock. ● For safety, always remove the power plug from the AC wall outlet if there is any danger of lightning striking in your area. Insert the shaft until it is no longer visible. ● Do not use the amplifier for any other purpose than powering a speaker system. 5  Thank you for purchasing the Yamaha BBT500-115/BBT500-110 Bass Amplifier. The BBT5001-115/BBT500-110 is an all-digital bass amplifier that utilizes Yamaha’s DSP technology to provide bassists with extensive sound tailoring capabilities and simple operation. Thanks to the use of a highly efficient digital power amplifier in combination with Yamaha’s power switching technology, the BBT500-115/BBT500-110 can deliver a maximum 500W of power into 2Ω. The BBT500-115/BBT500-110 offers bassists precision sound tailoring and control with its 11 sound variation types, 5-band semi-parametric equalizer, compressor, limiter, and noise gate. It is also equipped with a speaker simulator and effects loop for greater tone tailoring and versatility. The BBT500-115/BBT500-110 provides 5 internal memory locations that let you store up to five tone settings for instant recall at the press of a switch. It also offers MIDI compatibility and a bi-amp system (using two amplifiers to create a single system), etc. that make it an excellent choice for use in the studio or live performances. In order to get the most out of your BBT500-115/BBT500-110 and its sophisticated functions, please thoroughly read this Owner’s Manual before using the device. Also, keep the manual in a safe, convenient place for future reference. CONTENTS Panel Controls and Connections ........................................ 7 Front Panel .................................................................................. 7 Rear Panel .................................................................................. 8 Operating Instructions ...................................................... 11 Getting sound output ................................................................. 11 Adjusting the Input Level ........................................................... 11 Sound Setting ........................................................................... 11 Storing and Recalling Patches .................................................. 12 Detailed Parameter Settings ............................................. 13 Amp Mode ................................................................................. 13 Equalizer Mode ......................................................................... 14 Compressor Mode .................................................................... 14 Utility Mode ............................................................................... 15 Air Flow ............................................................................... 18 Error Messages .................................................................. 18 Troubleshooting ................................................................. 18 Specifications ..................................................................... 19 MIDI Implementation Chart ............................................... 95 6  Panel Controls and Connections Front Panel !0 q !1 w !2 e r !3 t q Power Switch This is the unit’s main power switch. * Always set the OUTPUT volume to “0” before switching the power ON or OFF to protect the speaker from damage. w Input Jack (INPUT) This is the unit’s input jack. Connect the output jack on your bass to this jack. * Make sure that the power is switched OFF before connecting the bass. * For U.S. and Canadian models only To protect against electromagnetic waves, attach the supplied Clamp Filter to the cable connecting the bass guitar to the amplifier. (→ pg. 10) e Input Level Volume (INPUT LEVEL) Adjusts the amplifier’s input volume level and the volume of the bass that is connected to the BBT500. Use the indicators located on either side of the knob to check the signal level. (→ pg. 11) * The INPUT LEVEL setting is not saved in memory. r Sound Type Select Switch (SOUND TYPE) Select one of the eleven preset sound variation types. The indicator of the selected sound type will light. (→ pg. 11) t Compressor Volume (COMP) Adjusts the compressor’s compression ratio. In the Equalizer mode, this knob is used to set the center frequency (PEQ F) of the 1-band parametric equalizer. (→ pg. 14) y Gain Volume (GAIN) y u i o i Tone Controls (BASS, LOW MID, MIDDLE, HIGH MID, TREBLE) Adjusts the level of their corresponding frequencies. In the Equalizer Mode, these knobs are used to set the center frequency (FREQ) for their corresponding tone control. (→ pg. 14) In the Compressor Mode, these knobs are used to adjust the parameters given below. (→ pg. 14) BASS ........... Compressor’s release (RELEASE) time LOW MID ..... Compressor’s output gain (C. GAIN) MIDDLE ....... Compressor’s knee (KNEE) HIGH MID .... Noise gate threshold (N. GATE) TREBLE ....... Effect loop blend level (BLEND) o Output Volume Level (OUTPUT) Adjusts the power amplifier’s output level. This knob is used to set the overall volume level (the amount delivered by the speaker) of the sound created by the pre-amplifier section’s GAIN, MASTER, Tone Controls, etc. Adjusting this volume level has no effect on tone. * The OUTPUT level setting is not saved in memory. * This setting does not effect the output level (volume) of the LINE OUT (!8, !9) jacks. !0 Manual Switch (MANUAL) This switch resets all parameter values (including Equalizer and Compressor mode settings) to the state they were in when the power was switched ON. All knobs function as labeled on the panel, and the setting for each control corresponds to the position of the knob. If you continuously hold the switch, all settings will be returned to the state that they were in just before the [MANUAL] or Memory switch was pressed (Undo Function). (→ pg. 13) Adjusts the pre-amplifier’s gain volume level. * When this knob is set to “0”, no sound will be produced although the Master Volume is turned up. In the Equalizer Mode, this knob is used to set the bandwidth (PEQ Q) of the 1-band parametric equalizer. (→ pg. 14) In the Compressor Mode, this knob is used to set the compressor threshold (THRSLD). (→ pg. 14) u Master Volume (MASTER) Adjusts the overall volume of the sound created with the Gain and Tone Control settings. Adjusts the preamplifier’s output level. * The MASTER volume setting is saved in memory. In the Equalizer Mode, this knob is used to set the Gain (PEQ G) volume level of the 1-band graphic equalizer. (→ pg. 14) In the Compressor Mode, this knob is used to adjust the compressor’s attack (ATTACK) time. (→ pg. 14) !1 Memory Switches (1-5) These switches are used to recall data for patches (1-5) saved in the unit’s memory. The selected memory’s (switch’s) indicator lights. (→ pg. 12) After editing patch data, press and hold the switch for about 1 second to save the data to memory. (→ pg. 12) !2 Display Displays information such as parameter values, etc. !3 Function Switch (FUNCTION) This switch is used to select the unit’s operating mode. • • • • Amp Mode (→ pg. 13) Equalizer Mode (→ pg. 14) Compressor Mode (→ pg. 14) Utility Mode (→ pg. 15) 7  Panel Controls and Connections Rear Panel Before making any connections, make sure that the power on the BBT500 and all other related devices is switched OFF. Mixer or Additional Amplifier Save patches to a MIDI device Headphones Use a MIDI controller to select patch memory STATUS DATA/CTRL BANK MSB/MAX BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM 8.8.8. DEC ±10 INC /NO /YES MEMORY EDIT PC EDIT WRITE /EXIT Outboard Effects Processor OUT !4 !5 MIDI OUT MIDI IN IN !6 !7 !8 !9 @0 @1 @2 @3 @7 @5 @4 Supplied power cable Internal Speaker Tuner Clamp Filter (→ pg. 10) * For U.S. and Canadian models only AC Power @6 External Speaker(s) !4 Tuner Output (TUNER OUT) !6 Headphones Jack (PHONES) This output jack is used to connect a tuner to the BBT500. It can also be used to create a bi-amp system. Connect this output jack to the INPUT jack on another BBT500. (→ pg. 15) This jack is used to connect a pair of headphones to the unit. It carries the same signal that is delivered from the LINE OUT jack. Use the LEVEL control to adjust the volume. !5 Effect Loop (FX LOOP) • Effect Send Jack (SEND) • Effect Return Jack (RETURN) • Effect Loop Level Switch (LEVEL) !7 Headphones/Line Out Level Control (LEVEL) These jacks let you insert an outboard effects processor between the SEND and RETURN jacks to apply effects to the BBT500’s signal. Use the Level Switch to match the Input/Output level with the level required by the outboard effects processor. Use the BLEND control in the Compressor Mode to adjust the balance level between the outboard effector’s sound and the sound that is created by the BBT500. (→ pg. 14) 8 Adjusts the output level of the PHONES jack and the LINE OUT jacks. (The same setting is applied to both jacks.) !8 Line Out Jack (UNBALANCED OUT) !9 Line Out Jack (BALANCED OUT) These jacks carry the signal that is selected with the @0 Line Out Source Switch at a line level. Both unbalanced phone type (+4 dB/10 kΩ) and balanced XLR type (+4 dB/600 Ω) jacks are provided. Use the LINE SOURCE switch to select the signal that is sent to the LINE OUT jack. As the unit is equipped with an output limiter and speaker simulator (can be switched ON/OFF), and the output level of these jacks is controlled by the LEVEL control, these jacks can be used to send a line level signal to a mixing console or an additional amplifier.  Panel Controls and Connections @0 Line Out Source Switch (LINE SOURCE: THRU/PRE EQ/POST EQ) This switch is used to select the signal that is delivered from the LINE OUT jack. THRU ........... Delivers the signal received via the INPUT jack without alteration. Select this setting when connecting to a DI (Direct Injection) box. PRE EQ ....... Delivers the signal before it has been processed by the tone controls (the Sound Type is active). This setting can be used when separate EQ settings are required for speaker and line outputs. POST EQ ..... Delivers the signal after it has been processed by the tone controls. This setting can be used when you want the line signal processed with the same EQ setting as the speaker. * The FX LOOP is active on both PRE EQ and POST EQ signals. @1 Speaker Simulator Switch (SP SIM: OFF/LINE/ON) This switch is used to switch the Speaker Simulator circuit ON/OFF. When the Speaker Simulator is activated, this special circuit adds the live characteristics of a speaker to the line out signal and headphones output. This feature is also effective when you want to produce a distorted sound with the tweeter level raised. The sound created with the Speaker Simulator is optimized to compliment the selected Sound Type. OFF .............. Deactivates the Speaker Simulator on LINE OUT, SPEAKER, and PHONES jack signals. LINE ............. Activates the Speaker Simulator on LINE OUT, and PHONES jack signals only. ON ................ Activates the Speaker Simulator on LINE OUT, SPEAKER, and PHONES jack signals. * The Speaker Simulator can only be applied to the LINE OUT jack output when the @0 Line Out Source Switch is set to “POST EQ”. @2 Output Limiter Switch (OUTPUT LIMITER: ON/OFF) This switch is used to switch the Output Limiter circuit ON/OFF. When set to the ON position, the limiter suppresses the signal if it exceeds the threshold before sending it to the SPEAKER jack and LINE OUT jack. OFF .............. Deactivates the Limiter on both LINE OUT and SPEAKER jack signals. ON ................ Activates the Limiter on both LINE OUT and SPEAKER jack signals. @3 MIDI OUT Jack Connect this jack to the MIDI IN jack on an external MIDI device that can save MIDI data (such as a MIDI data filer, etc.), and save patch data from the BBT500 to an external device. (→ pg. 17: MIDI Bulk Out) Also, when MIDI Merge is set ON, MIDI data received from an external MIDI device via the MIDI IN jack is transmitted from the MIDI OUT jack without alteration. (→ pg. 17) @5 Speaker Jacks (SPEAKER 1, 2 (EXT)) Two Speaker Jacks are provided for connecting speaker systems. The amp’s internal speaker (4 Ω) is connected to the SPEAKER 1 jack. The SPEAKER 2 (EXT) jack can be used to add an external speaker(s). Also, if necessary, you can disconnect the internal speaker to connect 2 external speakers directly to the amp. The two speaker jacks are connected in parallel. When external speakers are used, make sure the speakers meet the following requirements. ● When using a single SPEAKER Jack (1 or 2) Please use a system that complies with one of the following requirements. • The total impedance* of the circuit should never be less than 2Ω. • A 2Ω speaker system must have a power handling capability of 500W or greater. • A 4Ω speaker system must have a power handling capability of 250W or greater. • An 8Ω speaker system must have a power handling capability of 125W or greater. ● When using both SPEAKER Jacks (1 & 2) Please use a system that complies with one of the following requirements. • The total impedance* of the circuit should never be less than 2Ω. • A 4Ω speaker system must have a power handling capability of 250W or greater. • An 8Ω speaker system must have a power handling capability of 125W or greater. To obtain optimum performance from the amplifier, we recommend connecting the internal speaker to the SPEAKER 2 jack, and using the SPEAKER 1 jack to connect an external speaker (set) with a 4Ω impedance and power handling capacity of 250W or greater. * See page 10 for more information on total speaker impedance. * For U.S. and Canadian models only To protect against electromagnetic waves, attach the supplied Clamp Filters to the cables connecting the amplifier’s SPEAKER 1, 2 (EXT) jacks to the speakers. (→ pg. 10) @6 Tweeter Level Control (TWEETER LEVEL) This controls the built-in tweeter speaker’s output level (mainly high frequencies above 4 kHz). @7 Power Connector (AC IN) Connect the supplied power cable to this terminal to supply the unit with power from an AC power outlet. When connecting the power cable, make sure the amplifier’s POWER switch is turned OFF. @4 MIDI IN Jack Connect this jack to the MIDI OUT jack on MIDI Foot Controller, etc., to select patches, control volume, etc., with the MIDI Foot Controller. (→ pg. 16) Also, patches that have been saved to an external MIDI device can be loaded into the BBT500’s internal memory. (→ pg. 17: MIDI Bulk IN) 9  Panel Controls and Connections * Total Impedance Whenever two or more speaker cabinets are connected to the unit, consideration must be given to the total impedance of the speaker system. Normally, a speaker cabinet has an impedance of 4, 8 or 16Ω. But when two or more speaker cabinets are used together, the total impedance will change according to the manner in which the cabinets are connected. ● Connecting in a Series Total impedance = 1st Speaker + 2nd Speaker + 3rd Speaker … Connecting three 4Ω speaker cabinets in a series as shown below, results in a total impedance of 12Ω. As the BBT500-115’s and BBT500-110’s two speaker jacks are connected in a parallel circuit inside of the amplifier, adding a 4Ω external speaker to the 4Ω internal speaker will result in a total impedance of 2Ω. So in order to maintain a minimum impedance of 2Ω, an external speaker with an impedance of 4Ω or greater must be used. ● Connected in Parallel Total impedance = Connecting three 4Ω speaker cabinets in a parallel configuration as shown below, results in a total impedance of about 1.3Ω. 4 4 4 External Speaker Greater than 4 Ω ● Attaching the Clamp Filter Internal Speaker 4Ω (For U.S. and Canadian models only) To protect against electromagnetic waves, attach the supplied Clamp Filter to the cable connecting the bass guitar to the amplifier’s INPUT jack, and to the cable connecting the amplifier to an external speaker. * The cable connecting the internal speaker (SPEAKER 1 jack) is fitted with a Clamp Filter at the factory. * When attaching the clamp filter, wrap the cable once around the clamp filter as close to the BBT500 unit as possible. Cable Clamp Filter 10 Clamp Filter  Operating Instructions Sound Setting Getting sound output 1 First, make sure that the POWER switch is switched OFF, then connect your bass to the INPUT Jack on the front panel. 2 Rotate the OUTPUT knob fully to the left and then switch the POWER switch ON. To protect the speakers, make sure that the OUTPUT knob is set to “0” whenever switching the POWER switch ON or OFF. 3 First, set the INPUT LEVEL knob to its 12 O’clock position, then while playing the bass, gradually increase the GAIN, MASTER, and OUTPUT knobs to adjust the sound. 4 Once the system is producing sound, set the input level as described in the “Adjusting the Input Level” section below. When the power is switched ON, all control knobs function as labeled on the panel and described below. All lamps on the display above the control knobs and switches are unlit. Rotate the SOUND TYPE knob to select a sound type, then use the Tone Control knobs to shape the sound. Before selecting a sound type, first set the GAIN through TREBLE control knobs to their center positions then try out the different Sound Types. Also, the COMP knob is used to adjust the compressor’s compression ratio. The compressor automatically balances the differences between loud and soft levels when playing. Rotate the knob to the right to increase the amount of compression. q w e r t y u i o !0 !1 q INPUT LEVEL: Sets the Input Level Adjusting the Input Level The INPUT LEVEL control optimizes the signal received from the bass for use with the amplifier, to produce wide dynamic range and rich tone. A poorly adjusted level results in noise, feedback, a cutup sound, etc. * Since output levels vary from instrument to instrument, you will need to readjust the input level to match the instrument’s output level whenever you change instruments. 1 Rotate the volume control on your bass to its maximum level and play loudly while rotating the INPUT LEVEL knob. An ideal level is attained when the green indicator is lit. 2 Continue to rotate the INPUT LEVEL knob to the right making sure the red indicator does not light. As long as the red indicator does not light, rotate the knob fully to the right. w SOUND TYPE: Selects the Sound Type (11 types) FLAT ............ A clean tone with all frequencies set flat. This setting also works well with an upright bass or an electric-acoustic bass. TUBE ........... A clear and warm tube type sound. This setting also works well with an upright bass or an electric-acoustic bass. SOLID ......... A fat solid-state type sound R & B ........... A fat R & B type sound VINTAGE ..... A vintage tone with warm mid frequencies MODERN .... A modern sound with rich low-end and bright high-end CLASSIC ..... Rock bass sound HEAVY ........ A heavier sound than the CLASSIC setting DRIVE ......... Overdrive bass sound DIST ............ Distortion bass sound FUZZ ........... Fuzz bass sound e COMP: Compression Ratio (1.0 to ∞, 16 steps) This adjusts the compressor’s compression ratio and output levels simultaneously. As the value increases, so does the amount of compression applied to signals that exceed the threshold level (→ pg. 14). r GAIN: Pre-Amp Gain (0 to 10, 0.1 step) Set the knob so that the red indicator does not light. t MASTER: Master Volume (0 to 10, 0.1 step) y BASS: Bass Frequency (-15dB to +15dB, 0.2dB step) u LOW MID: Low Mid Frequency (-15dB to +15dB, 0.2dB step) i MIDDLE: Middle Frequency (-15dB to +15dB, 0.2dB step) o HIGH MID: High mid Frequency (-15dB to +15dB, 0.2dB step) !0 TREBLE: Treble Frequency (-15dB to +15dB, 0.2dB step) !1 OUTPUT: Sets the output level HINT Using the OUTPUT and MASTER Controls Both knobs can be used to control the overall volume however, the MASTER knob is the preamplifier’s master volume and its setting is saved in memory. The OUTPUT knob is the power amplifier’s output volume and its setting is not saved in memory. Use the MASTER knob to set individual volume settings of patches saved to memory, and use the OUTPUT knob to set the output volume level produced by the speakers. 11  Operating Instructions Storing and Recalling Patches After creating a sound that you like, you can store its settings in the unit’s internal memory. Sound setting data (individual knob settings) is called a Patch. Saving a patch to the unit’s internal memory is called Store. The BBT500 provides five memory locations for storing patch data. Patch data in the memory is stored even when the power is switched OFF, and can be recalled at any time by pressing the patch’s corresponding switch. Take note that unless the changes are saved to memory, any changes made to the patch will be lost when another patch is selected or when the power is switched OFF. Storing a Patch After creating a sound you want to keep for later use, press and hold any one of the Memory Switches (1-5) until all of the front panel indicators light. Ex.) Press and hold Memory Switch [1] until all indicators light. However, if the value set in the patch is different than the knob’s actual position, the patch’s value will flash in the display but it will not change, nor will the sound, even though you are turning the knob. For more information on this situation, refer to the “Knob Position and Settings” section below. ● Knob Position and Settings When a patch is recalled from memory, etc., it may be that the knob’s actual position differs from the value set in the recalled patch. In this case, the BBT500 is programmed to flash the patch’s value on the display without changing it or the sound until the knob’s position corresponds to the value in the recalled patch setting. If the display flashes when rotating the knob, continue rotating the knob until its position matches the flashing value. When the position and value match, the value will stop flashing on the display and change as the knob is turned. Ex.) If the GAIN knob is pointing at the “3 o’clock” position and a patch with a GAIN setting of 4.0 is recalled. * INPUT LEVEL and OUTPUT LEVEL settings are not stored in memory. Recalling a Patch To use one of the patches stored in memory, just press the Memory Switch [1]-[5] to which the data is stored. The indicator of the selected Memory Switch lights. Ex.) Recalling the patch stored to Memory Switch [2]. The value “4.0” flashes on the display but rotating the knob from the “3 o’clock” position to the “11 o’clock” position does not change anything. As the knob goes past the “11 o’clock” position and its position matches that of the value, the value will then stop flashing and start changing according to the knob’s position. ● The Useful “Undo” Function After you recall or store a patch, the value for each knob will appear in the display when the knob (COMP - TREBLE) is used. Setting Value 12 Press and hold the [MANUAL] switch activates the “Undo” function, which returns settings to the condition they were in prior to pressing a Memory Switch [1]-[5] or the [MANUAL] switch. This function is useful in cases such as: You’ve just made some changes to the patch saved in Memory Switch [1] but pressed Memory Switch [2] before you could save the changes to memory. Press and hold the [MANUAL] switch to return the settings to the same condition they were in before you pressed Memory Switch [2]. In the same manner, you made some changes to a patch but pressed the [MANUAL] switch before you could save those changes to memory. Press and hold the [MANUAL] button to restore your changes.  Detailed Parameter Settings The BBT500 also features more precise settings for defining the frequencies for each of the Tone Control knobs, operating the Compressor and Noise Gate, or setting the Blend Level of the effect loop, etc. To access these settings, press the [FUNCTION] switch and use the four Modes described below. • Amp Mode In this mode, each knob functions in the manner it is labeled on the front panel. • Equalizer Mode This mode is used to set the 1-band parametric equalizer and the center frequency for each of the Tone Controls (Bass – Treble). Amp Mode Each knob functions in the manner it is labeled on the panel. In the Amp Mode, the knob’s value (or patch’s setting value) is shown on the display when the knob is turned. * After the BBT500’s power is switched ON or the [MANUAL] switch is pressed, nothing is shown in the display until a Memory is recalled, or a mode other than the Amp Mode is selected. Enter the Amp Mode using one of the following methods. • The Amp Mode is the default mode when the BBT500’s power is switched ON. • Compressor Mode This mode is used to set the Compressor’s blend level, noise gate level, and effect loop. • Press the [MANUAL] Switch to enter the Amp Mode. • Utility Mode This mode is used to set the crossover filter, and individual MIDI settings. • In the Equalizer, Compressor, or Utility Mode, press the [FUNCTION] switch. Individual settings in the Amp Mode, Equalizer Mode, and Compressor Mode are saved when patch data is saved to the unit’s memory. Individual parameter settings in the Equalizer Mode and Compressor Mode are set to their default values when the power is switched ON. Individual settings in the Utility Mode are saved when exiting the Utility Mode, and they are retained even if the power is switched OFF. • Press a Memory Switch [1] – [5] to recall a patch. Or, press and hold a Memory Switch to save a patch to memory. ● How Knobs Function in the Amp Mode The knob’s value is shown on the display when the knob is turned. q w e r t y u i o !0 !1 Each control knob’s function in the Amp Mode is the same as described in the “Sound Setting” section (→ pg. 11). q INPUT LEVEL: Sets the Input Level w SOUND TYPE: Selects the Sound Type (11 types) e COMP: Compression Ratio (1.0 to ∞, 16 steps) r GAIN: Pre-Amp Gain (0 to 10, 0.1 step) t MASTER: Master Volume (0 to 10, 0.1 step) y BASS: Bass Frequency (-15dB to +15dB, 0.2dB step) u LOW MID: Low Mid Frequency (-15dB to +15dB, 0.2dB step) i MIDDLE: Middle Frequency (-15dB to +15dB, 0.2dB step) o HIGH MID: High mid Frequency (-15dB to +15dB, 0.2dB step) !0 TREBLE: Treble Frequency (-15dB to +15dB, 0.2dB step) !1 OUTPUT: Sets the output level 13  Detailed Parameter Settings Equalizer Mode Compressor Mode The Equalizer mode lets you make settings for the internal 1-Band Parametric Equalizer, and set the center frequency (or in the case of the TREBLE control knob, its cutoff frequency) for each of the panel’s Tone Controls (BASS – TREBLE) in the internal five-band equalizer. The Compressor Mode provides settings for the Compressor, Noise Gate, and Blend Level for the effect loop. To enter the Equalizer mode, press the [FUNCTION] switch. Knob functions are displayed in the bottom row of the panel display above the knobs. ● How Knobs Function in the Equalizer Mode The knob’s value is shown on the display when the knob is turned. q w e The function of each knob is displayed here. r t y u i o !0 !1 To enter the Compressor Mode, press and hold the [FUNCTION] switch until the knob functions are displayed in the upper row of the panel display above the knobs (the row above that used by the Equalizer Mode). ● How Knobs Function in the Compressor Mode The knob’s value is shown on the display when the knob is turned. q w e r t The function of each knob is displayed here. y u i o !0 !1 q INPUT LEVEL: Sets the Input Level q INPUT LEVEL: Sets the Input Level w SOUND TYPE: No function. w SOUND TYPE: No function. e COMP (PEQ F): Sets the center frequency of the 1-band parametric equalizer (20Hz to 20.0kHz, 255 steps) e COMP (RATIO): Compression ratio (1.0 - ∞, 16 steps) *operates the same as COMP in the Amp Mode. r GAIN (THRSLD): Compressor threshold level (-54dB to 0dB, 1dB step) r GAIN (PEQ Q): Sets the bandwidth of the 1-band parametric equalizer. (0.1 to 20.0, 255 steps) t MASTER (PEQ G): Sets the gain level of the 1-band parametric equalizer. (-15dB to +15dB, 0.2dB step) y BASS (FREQ): Sets the center frequency of the BASS control knob. (20Hz to 320Hz, 255 steps) u LOW MID (FREQ): Sets the center frequency of the LOW MID control knob. (80Hz to 1.28kHz, 255 steps) i MIDDLE (FREQ): Sets the center frequency of the MIDDLE control knob. (250Hz to 4.00kHz, 255 steps) o HIGH MID (FREQ): Sets center frequency of the HIGH MID control knob. (500Hz to 8.00kHz, 255 steps) !0 TREBLE (FREQ): Sets the center/cutoff frequency of the TREBLE control knob. (1.25kHz to 20.0kHz, 255 steps) !1 OUTPUT: Sets the output level Sets the signal level from which the compressor will activate. Compression is applied to signals that exceed this level. t MASTER (ATTACK): Compressor attack time (0msec to 120msec, 1msec step). Sets the amount of time required for application of the compressor from the time the signal exceeds the threshold. When a slow attack time is set, the beginning of the attack will not be compressed. y BASS (RELEASE): Compressor release time (5msec to 42.3 sec, 160 steps). Sets the amount of time required for the compressor to switch off after the signal goes below the threshold level. This smoothes gain changes to keep the sound natural. u LOW MID (C. GAIN): Compressor gain (0dB to 18dB, 0.1dB step) This parameter works in conjunction with the compressor ratio setting which is set with the e COMP (RATIO) control knob. In other words, gain is automatically adjusted along with amount of compression applied to the signal. If the Ratio = “1.0”, Gain = “0”. If the Ratio = “∞”, Gain = the setting determined with the control knob. i MIDDLE (KNEE): Compressor knee (Hd (Hard), 1, 2, 3, 4, 5) r PEQ Q + Sets the depth of signal compression after the input signal exceeds the threshold level. When set to Hd (hard), compression starts soon with the ratio you have set. However, when set to 1-5, compression startup is gradual, creating a more natural sound (soft knee compression). 0.1 0 Frequency t PEQ G Gain 20 – o HIGH MID (N. GATE): Noise gate threshold level (OFF, -53dB to 0dB, 1dB step) When the input signal’s level falls below this set level, the noise gate activates cutting off the signal. !0 TREBLE (BLEND): Blend level between the effect loop’s RETURN signal e PEQ F and the dry signal (the sound created in the BBT500) (0% (Return 0%, Dry 100%) to 100% (Return 100%, Dry 0%)). !1 OUTPUT: Sets the output level 14  Detailed Parameter Settings Utility Mode Crossover Filter The Utility Mode provides settings for the Crossover Filter and MIDI. These settings are saved internally when you exit the Utility Mode and kept even when the amplifier’s power is switched OFF. By connecting two BBT500s as shown in the illustration below, you can create a bi-amplified system, where one amplifier is used to drive high frequencies and a second amplifier drives low. This system uses the amplifier’s onboard crossover filter (LPF or HPF) to determine the range of frequencies that each amplifier will deliver. ● Entering the Utility Mode To enter the Utility Mode, from any mode press and hold the [FUNCTION] switch for more than 3 seconds, until “utL” appears on the display. ● Setting the Crossover Filter 1 Press and hold the [FUNCTION] switch for more than three seconds (until “utL” appears on the display) to enter the Utility Mode. 2 Rotate the COMP knob to set the Crossover filter’s cutoff frequency. * Range of cutoff frequency L10 (LPF 100Hz) to L00 (LPF 1000Hz), byP (Bypass), h10 (HPF 100Hz) to h00 (HPF 1000Hz), 93 steps ● How Knobs Function in the Utility Mode In the Utility Mode, only the INPUT LEVEL, OUTPUT, and COMP knobs function. All other knobs (SOUND TYPE, GAIN - TREBLE) have no function. • INPUT LEVEL: Sets the Input Level • OUTPUT: Sets the output level When using a bi-amplified system, make sure that the INPUT LEVEL control knob on the second BBT500 is set to its minimum level. Ex.) Operating a bi-amplified system in which the crossover filter on the first amplifier is set to h50 (HPF 500Hz) to produce high frequencies, and the crossover filter on the second amplifier is set to L50 (LPF 500Hz) to produce low frequencies. • COMP: Sets the cut off frequency of the crossover filter When the COMP knob is used (when setting the crossover filter), the setting’s value is shown in the display. Other than that, only utL appears on the display. Use the [MANUAL] switch and Memory Switches [1] through [5] to set individual MIDI settings. (→ [MIDI Settings] pg. 16) Individual MIDI Settings First amplifier (HPF 500Hz) Bass When the COMP knob is used (when setting the crossover filter), the setting’s value is shown in the display. Other than that, only utL appears on the display. TUNER OUT INPUT * Set to “h50” with the COMP control knob Second amplifier (LPF500Hz) Produces higher frequencies above 500Hz INPUT q w e * Set the INPUT LEVEL to its minimum level * Set to “L50” with the COMP control knob Produces low frequencies up to 500Hz 15  Detailed Parameter Settings MIDI Settings The BBT500 is MIDI* compatible and equipped with MIDI IN and MIDI OUT jacks. * What is MIDI? The acronym for Musical Instruments Digital Interface, MIDI is a worldwide standard communication interface that allows MIDI compatible musical instruments, computers, and other MIDI devices to share musical information and control one another regardless of instrument type or maker. 3 Create a Program Change Map*. (Default → Program Change No: Memory No = 1:1, 2:2, 3:3, 4:4, 5:5, 6:1, 7:2, 8:3 …) * What is a Program Change Map? A Program Change Map assigns a program change number (received via MIDI) to a memory number. For example, when the BBT500 receives “Program Change Number 1” from an external MIDI device, it will recall memory number “3”. This is also called a Program Change Table. With MIDI functions you can do things like select a patch from the BBT500’s memory using an external MIDI device like the MFC10 Yamaha MIDI Foot Controller, etc. You can also backup data by sending the contents in the unit’s memory to a device that is capable of saving MIDI data (Yamaha MDF3, etc.). 3-1 Press and hold the [FUNCTION] switch for more than 3 seconds (until “utL” appears on the display) to enter the Utility Mode. ● Selecting a Patch with MIDI 3-2 While holding the [MANUAL] switch, press Memory Switch [1]. The currently assigned MIDI program change number appears on the display (after a few seconds, the display will return to “utL”). 1 Using a MIDI cable, connect the MIDI IN jack on the BBT500 to the MIDI OUT jack on the external MIDI device. * Use only a standard MIDI cable that is less than 15 meters in length. Use of a longer cable can result in trouble such as abnormal operation, etc. Receive Program Change Number MIDI Cable BBT500 Rear Panel MIDI IN MIDI OUT STATUS DATA/CTRL BANK MSB/MAX BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM 8.8.8. DEC ±10 INC /NO /YES MEMORY EDIT PC EDIT WRITE /EXIT 3-3 Use Memory Switches [1] and [2] to set the program change number (1-128) that is received by the BBT500. Use Memory Switch [2] to increase the value and Memory Switch [1] to decrease the value. 3-4 While holding the [MANUAL] switch, press Memory Switch [2]. The memory number that will be recalled when the program change number that was set in step 3-3, appears on the display. (After a few seconds, the display will return to “utL”). External MIDI Device 2 Set the MIDI receive channel on the BBT500 and the MIDI transmit channel on the external device to the same MIDI channel. (Default channel: 1) * MIDI data can not be transmitted or received if the MIDI channels are not properly matched. 2-1 Press and hold the [FUNCTION] switch for more than three seconds (until “utL” appears on the display) to enter the Utility Mode. 2-2 While holding the [MANUAL] switch, press Memory Switch [3]. The currently assigned MIDI receive channel appears on the display (after a few seconds, the display will return to “utL”). Memory Number 3-5 Use Memory Switches [1] and [2] to set the memory number (1-5) that corresponds to the program change number received by the BBT500. Uses Memory Switch [2] to increase the value and Memory Switch [1] to decrease the value. 3-6 If necessary, repeat steps 3-2 through 3-5. 3-7 Press the [FUNCTION] switch to enter the Amp Mode. MIDI Receive Channel 4 2-3 Use Memory Switches [1] and [2] to set the MIDI receive channel (1-16, ALL, oFF). Use Memory Switch [2] to increase the value, and Memory Switch [1] to decrease the value. * “ALL” is set to Omni On. When “oFF” is set, MIDI data will not be received. 16 Now, when a program change number transmitted from an external MIDI device is received by the BBT500, it will recall the corresponding memory number that is set in the program change map you just created will be recalled. * Refer to the Owner’s Manual that came with your MIDI device on how to receive or transmit program change data.  Detailed Parameter Settings ● MIDI Merge Settings 4 If you want MIDI signals received by the BBT500’s MIDI IN jack transmitted without alteration to other MIDI devices connected to the BBT500’s MIDI OUT jack, set the MIDI Merge to “on”, if not, set it to “oFF”. 1 Press and hold the [FUNCTION] switch for more than three seconds (until “utL” appears on the display) to enter the Utility Mode. 2 While holding the [MANUAL] switch, press Memory Switch [4]. The current MIDI Merge setting appears on the display (after a few seconds the display will return to “utL”). MIDI Merge Setting Use Memory Switches [1] and [2] to set the type of data (1-5, ALL) to be sent with the Bulk Out operation. 1-5 ...... Sends only the data from the selected memory number. ALL ..... Sends all data in memory numbers 1-5 and Utility Mode settings. 5 Press Memory Switch [5] to carry out the Bulk Out operation. While the Bulk Out operation is in progress, all lamps on the unit will light. * The device number becomes the MIDI receive channel number (→ pg. 16). When the MIDI receive channel is set to “ALL” (Omni ON), the channel is set to 1. 6 Press the [FUNCTION] switch to enter the Amp Mode. ● About MIDI Control Changes 3 Use Memory Switches [1] and [2] to set MIDI Merge either “on” (Memory Switch [2]) or “oFF” (Memory Switch [1]). 4 Press the [FUNCTION] switch to enter the Amp Mode. You can use the MIDI Bulk Out operation to back up data saved in the BBT500 (data in memory 1-5 and Utility Mode settings) to a device that can save MIDI data (such as a Yamaha MDF3, etc.). Using a MIDI cable, connect the MIDI OUT jack on the BBT500 to the MIDI IN jack on an external MIDI device. * Use only a standard MIDI cable that is less than 15 meters in length. Use of a longer cable can result in trouble such as abnormal operation, etc. MIDI Cable BBT500 Rear Panel * With the exception of the Number 7 Control Change, the BBT500 does not recognize any other MIDI Control Change messages. * The Main Volume data will not change, even if a different memory number is selected. ● MIDI Bulk Out 1 You can control the overall volume of the BBT500 by connecting an external MIDI device’s MIDI OUT jack to the BBT500’s MIDI IN jack, and transmit Number 7 Control Change Messages (Main Volume) to the BBT500. MIDI IN * When the POWER is switched ON, the Main Volume data is set to its MAX value. * After the Main Volume data is changed, and the external MIDI device is disconnected, the pre-amp’s volume level may not be sufficient. If this case occurs, transmit a Control Change with a higher volume setting again, or switch the POWER OFF and then back ON. ● About MIDI Bulk In Using a MIDI cable, connect the MIDI IN jack on the BBT500 to the MIDI OUT jack on an external MIDI device to return data that has been stored on the external device, to the BBT500’s memory. This operation is referred to as MIDI Bulk In. * The device number becomes the MIDI receive channel number (→ pg. 15). When the MIDI receive channel is set to “ALL” (Omni ON), the channel is set to 1. When set to “oFF” (OFF) data will not be received. MIDI OUT * “Ld” appears on the display while receiving MIDI Bulk data. External MIDI Device 2 Hold the [FUNCTION] switch for more than three seconds (until “utL” appears on the display) to enter the Utility Mode. 3 While holding the [MANUAL] switch, press Memory Switch [5]. The type of data to be sent with the Bulk Out operation appears on the display (after a few seconds the display will return to “utL”). Type of data to be sent with the Bulk Out operation. ● Sending/Receiving MIDI Data Between Two BBT500s The MIDI Bulk In or MIDI Bulk Out operations can be used to copy memory or Utility Setup data in one BBT500 to another BBT500. ● Restoring the Factory Presets This operation clears the contents of the BBT500’s memory 1-5 and restores all parameters to their factory preset settings. While holding the [MANUAL] switch and Memory Switch [5], switch the POWER switch ON. 17  Air Flow The device utilizes a forced air cooling system, which cools the interior of the unit by drawing air through the front intake by the fan, which push the air out the back. Front view Rear view Intake Error Messages If an error occurs during operation, one of the following error message numbers will appear on the display. E1: MIDI Receive Buffer Full CAUSE: Too much MIDI data is being received by the BBT500 at one time. SOLUTION: Try reducing the amount of data being sent or, break the data into smaller blocks. E2: Communication Error. CAUSE: An abnormality is detected during MIDI communications. SOLUTION: Check all connections, etc. and try again. E3: Bulk Receive Check Sum Error. CAUSE: The check sum does not match the received MIDI bulk data. SOLUTION: Check all connections and data, and try again. E4: MIDI Receive Data Abnormality. CAUSE: An abnormality is detected in the received MIDI data. SOLUTION: Check all connections and data, and try again. Troubleshooting • No Sound → Is the power cord properly connected to the device? → Is the volume turned up on the instrument connected to the INPUT jack? → Are the INPUT LEVEL, GAIN, MASTER, OUTPUT control knobs set to “0”? → Check the Effect Loop’s BLEND setting (Compressor Mode: TREBLE control knob). Unless an external effector is connected to the device, raising the BLEND control will result in lowering the original sound. If the BLEND control is set to “100”, the original sound will not be produced. • Sound output is low → Is the volume turned up on the instrument connected to the INPUT jack? → Are the INPUT LEVEL, GAIN, MASTER, OUTPUT control knobs turned up? → Check the Effect Loop’s BLEND setting (Compressor Mode: TREBLE control knob). Unless an external effector is connected to the device, raising the BLEND control will result in lowering the original sound. If the BLEND control is set to “100”, the original sound will not be produced. → Check the Compressor setting. A low Threshold setting or a high Ratio setting will result in a lowered the output signal level. Also, a long release setting or low Compressor Gain setting will result in a lowered output signal level. 18 Cooling fan Exhaust  Specifications Power Amplifier Section Class-D power amplifier circuitry Output 250 W/4Ω (When used alone) 500 W/2Ω (Max output with external speaker connected) Speaker Section Speaker Power Handling Impedance BBT500-115 : 15” Woofer x1, Tweeter x1 BBT500-110 : 10” Woofer x1, Tweeter x1 250 Wrms 4Ω Preamplifier Section All digital signal processing Sound Type: 11 Presets 5-Band Semi Parametric Tone Controls (Variable Frequencies) Parametric Equalizer (PEQ, F, G, Q) A/D Conversion 24 bit D/A Conversion 24 bit Effect Section Compressor RATIO, THRSLD, ATTACK, RELEASE, C. GAIN, KNEE Limiter ON/OFF (SPEAKER, LINE OUT) Noise Gate N. GATE Crossover Filter LPF/HPF, Cutoff Frequency Speaker Simulator ON/LINE/OFF (SPEAKER, LINE OUT) 48 kHz Input Level/Impedance INPUT: -37dBm (thru)/1 MΩ FX LOOP RETURN: -20 dBm/220 kΩ, +4 dBm/220 kΩ Output Level/Impedance Effect Loop Monaural Send/Return, Level Switch (-20 dB/+4 dB), Effect Blend Control User Memory 5 User Memory (Sound Type, Amp Settings, Compressor, Effect Blend) SPEAKER (BRIDGED OUT): 500 Wrms/2 Ω, 250 Wrms/4 Ω LINE OUT (UNBALANCED OUT): +4 dBm/10 kΩ LINE OUT (BALANCED OUT): +4 dBm/600 Ω FX LOOP SEND: -20 dBm/100 kΩ, +4 dBm/100 kΩ Power Requirements U.S. and Canadian models : 120 V, 60 Hz General model : 230 V, 50-60 Hz MIDI Functions Receive Transmit Sampling Frequency Program Change, Control Change, Bulk In Bulk Out, Merge Out Power Consumption 130W Controllers/Switches Front Panel Rear Panel Control Knobs x 11, Push Switches x 7 Control Knob x1, Slide Switches x4 Displays Push Switch LED x5 Sound Type LED x11 7-Segment LED x3 Digit Input Level LED x2 (Green, Red) Connections INPUT: Standard Monaural Phone Jack SPEAKER 1, 2 (EXT): Standard Monaural Phone Jack PHONES: Standard Stereo Phone Jack LINE OUT (UNBALANCED OUT): Standard Monaural Phone Jack LINE OUT (BALANCED OUT): XLR Jack FX LOOP (SEND/RETURN): Standard Monaural Phone Jack TUNER OUT: Standard Monaural Phone Jack MIDI IN, MIDI OUT: 5-pin DIN jack Dimensions (W x H x D) BBT500-115 490 x 630 x 328 mm (19-5/16” x 12-15/16” x 24-13/16”) BBT500-110 432 x 480 x 301 mm (17” x 11-7/8” x 18-7/8”) Weight BBT500-115 U.S. and Canadian models : 23.9 kg (52 lbs. 11 oz) General model : 24.4 kg (53 lbs. 13 oz) BBT500-110 U.S. and Canadian models : 19.6 kg (43 lbs. 3 oz) General model : 20.1 kg (44 lbs. 5 oz) Accessories Power Cable Casters x4 (BBT500-115 only) Owner’s Manual (this booklet) Patch List Clamp Filters x2 (U.S. and Canadian models only) * Design and specifications may change without notice due to improvements. 19  YAMAHA [ Bass Amplifier ] Date:23-Dec-2003 Model BBT500 MIDI Implementation Chart Version : 1.0 +----------------------------------------------------------------------+ : : Transmitted : Recognized : Remarks : : Function ... : : : : :-------------------+----------------+----------------+----------------: :Basic Default : x : 1 - 16, off : memorized : :Channel Changed : x : 1 - 16, off : : :-------------------+----------------+----------------+----------------: : Default : x : 1,3 : memorized : :Mode Messages : x : x : : : Altered : ************** : x : : :-------------------+----------------+----------------+----------------: :Note : x : x : : :Number : True voice: ************** : x : : :-------------------+----------------+----------------+----------------: :Velocity Note ON : x : x : : : Note OFF : x : x : : :-------------------+----------------+----------------+----------------: :After Key's : x : x : : :Touch Ch's : x : x : : :-------------------+----------------+----------------+----------------: :Pitch Bender : x : x : : :-------------------+----------------+----------------+----------------: : 0 6 : x : x : : : 7 : x : o : Main Volume : : 8 - 127 : x : x : : : : : : : : Control : : : : : : : : : : Change : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :-------------------+----------------+----------------+----------------: :Prog : x : o 0 - 127 : Program Change : :Change : True # : ************** : : Number 1-128 : :-------------------+----------------+----------------+----------------: :System Exclusive : o : o : Bulk Dump : :-------------------+----------------+----------------+----------------: :System : Song Pos. : x : x : : : : Song Sel. : x : x : : :common : Tune : x : x : : :-------------------+----------------+----------------+----------------: :System :Clock : x : x : : :Real Time :Commands: x : x : : :-------------------+----------------+----------------+----------------: :Aux :All Sound OFF: x : x : : : :Reset All Cntrls : x : x : : : :Local ON/OFF : x : x : : : :All Notes OFF: x : x : : :Mes- :Active Sense : o : x : : :sages:Reset : x : x : : :-------------------+----------------+----------------+----------------: : : : : +-------------------+----------------+----------------+----------------+ Mode 1 : OMNI ON, POLY Mode 2 : OMNI ON, MONO o : Yes Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF, MONO x : No 95  WD59190 Printed in China