Yamaha SHS-500 de handleiding

Type
de handleiding
EN
Owners Manual
Before using the instrument,
be sure to read “PRECAUTIONS” on pages 5–7.
2 SHS-500 Owner’s Manual
For SHS-500
SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply
(adapter). DO NOT connect this product to any power supply or
adapter other than one described in the manual, on the name
plate, or specifically recommended by Yamaha.
WARNING: Do not place this product in a position where any-
one could walk on, trip over, or roll anything over power or con-
necting cords of any kind. The use of an extension cord is not
recommended! If you must use an extension cord, the minimum
wire size for a 25’ cord (or less) is 18 AWG. NOTE: The smaller
the AWG number, the larger the current handling capacity. For
longer extension cords, consult a local electrician.
This product should be used only with the components supplied
or; a cart, rack, or stand that is recommended by Yamaha. If a
cart, etc., is used, please observe all safety markings and instruc-
tions that accompany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct
at the time of printing. However, Yamaha reserves the right to
change or modify any of the specifications without notice or obli-
gation to update existing units.
This product, either alone or in combination with an amplifier and
headphones or speaker/s, may be capable of producing sound
levels that could cause permanent hearing loss. DO NOT operate
for long periods of time at a high volume level or at a level that is
uncomfortable. If you experience any hearing loss or ringing in
the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period
before damage occurs.
Some Yamaha products may have benches and / or accessory
mounting fixtures that are either supplied with the product or as
optional accessories. Some of these items are designed to be
dealer assembled or installed. Please make sure that benches
are stable and any optional fixtures (where applicable) are well
secured BEFORE using.
Benches supplied by Yamaha are designed for seating only. No
other uses are recommended.
NOTICE:
Service charges incurred due to a lack of knowledge relating to
how a function or effect works (when the unit is operating as
designed) are not covered by the manufacturer’s warranty, and
are therefore the owners responsibility. Please study this manual
carefully and consult your dealer before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and
environmentally friendly. We sincerely believe that our products
and the production methods used to produce them, meet these
goals. In keeping with both the letter and the spirit of the law, we
want you to be aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable battery
which (if applicable) is soldered in place. The average life span of
this type of battery is approximately five years. When replace-
ment becomes necessary, contact a qualified service representa-
tive to perform the replacement.
This product may also use “household” type batteries. Some of
these may be rechargeable. Make sure that the battery being
charged is a rechargeable type and that the charger is intended
for the battery being charged.
When installing batteries, never mix old batteries with new ones,
and never mix different types of batteries. Batteries MUST be
installed correctly. Mismatches or incorrect installation may result
in overheating and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all
batteries away from children. Dispose of used batteries promptly
and as regulated by the laws in your area. Note: Check with any
retailer of household type batteries in your area for battery dis-
posal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some
reason its useful life is considered to be at an end, please
observe all local, state, and federal regulations that relate to the
disposal of products that contain lead, batteries, plastics, etc. If
your dealer is unable to assist you, please contact Yamaha
directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the product. The
model number, serial number, power requirements, etc., are
located on this plate. You should record the model number, serial
number, and the date of purchase in the spaces provided below
and retain this manual as a permanent record of your purchase.
Model
Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
92-BP (bottom)
* This applies only to products distributed by Yamaha Corporation of America.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Digital Keyboard
Model Name : SHS-500
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
(FCC DoC)
SHS-500 Owner’s Manual 3
For AC adaptor and SHS-500
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modifica-
tions not expressly approved by Yamaha may void your
authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that your use of this
product in a residential environment will not result in harmful
interference with other electronic devices. This equipment
generates/uses radio frequencies and, if not installed and
used according to the instructions found in the users manual,
may cause interference harmful to the operation of other elec-
tronic devices. Compliance with FCC regulations does not
guarantee that interference will not occur in all installations. If
this product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”, please
try to eliminate the problem by using one of the following mea-
sures:
Relocate either this product or the device that is being affected
by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distribute
this type of product. If you can not locate the appropriate
retailer, please contact Yamaha Corporation of America, Elec-
tronic Service Division, 6600 Orangethorpe Ave, Buena Park,
CA90620
The above statements apply ONLY to those products distrib-
uted by Yamaha Corporation of America or its subsidiaries.
FCC INFORMATION (U.S.A.)
* This applies only to products distributed by Yamaha Corporation of America. (class B)
4 SHS-500 Owner’s Manual
For AC adaptor
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
“dangerous voltage” within the products
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11 Only use attachments/accessories specified by
the manufacturer.
12 Use only with the cart,
stand, tripod, bracket, or
table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid
injury from tip-over.
13 Unplug this apparatus during lightning storms
or when unused for long periods of time.
14 Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
(UL60065_03)
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
SHS-500 Owner’s Manual 5
PRECAUTIONS
PLEASE READ CAREFULLY
BEFORE PROCEEDING
Please keep this manual in a safe and
handy place for future reference.
WARNING
This AC adaptor is designed for use with only
Yamaha electronic instruments. Do not use for
any other purpose.
Indoor use only. Do not use in any wet
environments.
CAUTION
When setting up, make sure that the AC outlet
is easily accessible. If some trouble or
malfunction occurs, immediately turn off the
power switch of the instrument and disconnect
the AC adaptor from the outlet. When the AC
adaptor is connected to the AC outlet, keep in
mind that electricity is flowing at the minimum
level, even if the power switch is turned off.
When you are not using the instrument for a
long time, make sure to unplug the power cord
from the wall AC outlet.
WARNING
Always follow the basic precautions listed
below to avoid the possibility of serious
injury or even death from electrical shock,
short-circuiting, damages, fire or other
hazards. These precautions include, but
are not limited to, the following:
Power supply/AC adaptor
Do not place the power cord near heat
sources such as heaters or radiators. Also, do
not excessively bend or otherwise damage the
cord, or place heavy objects on it.
Only use the voltage specified as correct for
the instrument. The required voltage is printed
on the name plate of the instrument.
Use the specified adaptor (page 35) only.
Using the wrong adaptor can result in damage
to the instrument or overheating.
Check the electric plug periodically and
remove any dirt or dust which may have
accumulated on it.
Do not open
This instrument contains no user-serviceable
parts. Do not open the instrument or attempt to
disassemble or modify the internal
components in any way. If it should appear to
be malfunctioning, discontinue use
immediately and have it inspected by qualified
Yamaha service personnel.
Location (if Bluetooth
functionality is included)
(For information on whether Bluetooth
functionality is included or not, refer to page 9.)
Radio waves may affect electro-medical
devices.
- Do not use this product near medical
devices or inside areas in which the use of
radio waves is restricted.
- Do not use this product within 15 cm (6 in.) of
persons with a heart pacemaker implant.
Water warning
Do not expose the instrument to rain, use it
near water or in damp or wet conditions, or
place on it any containers (such as vases,
bottles or glasses) containing liquids which
might spill into any openings. If any liquid such
as water seeps into the instrument, turn off the
power immediately and unplug the power cord
from the AC outlet. Then have the instrument
For AC adaptor
For the instrument
DMI-5 1/3
6 SHS-500 Owner’s Manual
inspected by qualified Yamaha service
personnel.
Never insert or remove an electric plug with
wet hands.
Fire warning
Do not put burning items, such as candles, on
the unit.
A burning item may fall over and cause a fire.
Battery
Follow the precautions below. Failure to do so
might result in explosion, fire, overheating or
battery fluid leakage.
- Do not tamper with or disassemble batteries.
- Do not dispose of batteries in fire.
- Do not attempt to recharge batteries that are
not designed to be charged.
- Keep the batteries separate from metallic
objects such as necklaces, hairpins, coins,
and keys.
- Use the specified battery type (page 35)
only.
- Use new batteries, all of which are the same
type, same model, and made by the same
manufacturer.
- Always make sure all batteries are inserted in
conformity with the +/- polarity markings.
- When the batteries run out, or if the
instrument is not to be used for a long time,
remove the batteries from the instrument.
- When using Ni-MH batteries, follow the
instructions that came with the batteries. Use
only the specified charger device when
charging.
Keep batteries away from small children who
might accidentally swallow them.
If the batteries do leak, avoid contact with the
leaked fluid. If the battery fluid should come in
contact with your eyes, mouth, or skin, wash
immediately with water and consult a doctor.
Battery fluid is corrosive and may possibly
cause loss of sight or chemical burns.
If you notice any abnormality
When one of the following problems occur,
immediately turn off the power switch and
disconnect the electric plug from the outlet. (If
you are using batteries, remove all batteries
from the instrument.) Then have the device
inspected by Yamaha service personnel.
- The power cord or plug becomes frayed or
damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the
instrument.
- There is a sudden loss of sound during use
of the instrument.
CAUTION
Always follow the basic precautions listed
below to avoid the possibility of physical
injury to you or others, or damage to the
instrument or other property. These
precautions include, but are not limited to,
the following:
Power supply/AC adaptor
Do not connect the instrument to an electrical
outlet using a multiple-connector. Doing so
can result in lower sound quality, or possibly
cause overheating in the outlet.
When removing the electric plug from the
instrument or an outlet, always hold the plug
itself and not the cord. Pulling by the cord can
damage it.
Remove the electric plug from the outlet when
the instrument is not to be used for extended
periods of time, or during electrical storms.
Location
Do not place the instrument in an unstable
position where it might accidentally fall over.
Before moving the instrument, remove all
connected cables, to prevent damage to the
cables or injury to anyone who might trip over
them.
DMI-5 2/3
SHS-500 Owner’s Manual 7
When setting up the product, make sure that
the AC outlet you are using is easily
accessible. If some trouble or malfunction
occurs, immediately turn off the power switch
and disconnect the plug from the outlet. Even
when the power switch is turned off, electricity
is still flowing to the product at the minimum
level. When you are not using the product for a
long time, make sure to unplug the power cord
from the wall AC outlet.
Connections
Before connecting the instrument to other
electronic components, turn off the power for
all components. Before turning the power on
or off for all components, set all volume levels
to minimum.
Be sure to set the volumes of all components
at their minimum levels and gradually raise the
volume controls while playing the instrument to
set the desired listening level.
Handling caution
Do not insert a finger or hand in any gaps on
the instrument.
Never insert or drop paper, metallic, or other
objects into the gaps on the panel or
keyboard. This could cause physical injury to
you or others, damage to the instrument or
other property, or operational failure.
Do not rest your weight on, or place heavy
objects on the instrument, and do not use
excessive force on the buttons, switches or
connectors.
Do not use the instrument/device or
headphones for a long period of time at a high
or uncomfortable volume level, since this can
cause permanent hearing loss. If you
experience any hearing loss or ringing in the
ears, consult a physician.
When using a strap, make sure the strap is
securely attached to the instrument.
Do not lift the instrument by the strap. It can
cause serious injury or damage to the
instrument.
Do not treat the instrument in a rough manner
such as swinging it about, etc. The strap on
the instrument may detach causing
unexpected accidents such as the instrument
dropping, etc., or injuring persons close by.
Always turn the power off when the instrument is
not in use.
Even when the [ ] (Standby/On) switch is in
standby status (display is off), electricity is still
flowing to the instrument at the minimum level.
When you are not using the instrument for a long
time, make sure you unplug the power cord from
the wall AC outlet.
Make sure to discard used batteries according to
local regulations.
Yamaha cannot be held responsible for
damage caused by improper use or
modifications to the instrument, or data that
is lost or destroyed.
DMI-5 3/3
The model number, serial number, power requirements, etc., may be found on or near the name
plate, which is at the bottom of the unit. You should note this serial number in the space provided
below and retain this manual as a permanent record of your purchase to aid identification in the
event of theft.
Model No.
Serial No.
(bottom_en_01)
8 SHS-500 Owner’s Manual
NOTICE
To avoid the possibility of malfunction/ damage
to the product, damage to data, or damage to
other property, follow the notices below.
Handling
Do not use the instrument in the vicinity of a
TV, radio, stereo equipment, mobile phone, or
other electric devices. Otherwise, the
instrument, TV, or radio may generate noise.
When you use the instrument along with an
application on your iPad, iPhone or iPod
touch, we recommend that you set “Airplane
Mode” to “ON” on the device and then the
Bluetooth
®
setting to “ON” in order to avoid
noise caused by communication.
Do not expose the instrument to excessive
dust or vibrations, or extreme cold or heat
(such as in direct sunlight, near a heater, or in
a car during the day) to prevent the possibility
of panel disfiguration, damage to the internal
components or unstable operation. (Verified
operating temperature range: 5° – 40°C, or
41° – 104°F.)
Do not place vinyl, plastic or rubber objects
on the instrument, since this might discolor
the panel or keyboard.
Maintenance
When cleaning the instrument, use a soft and
dry cloth. Do not use paint thinners, solvents,
alcohol, cleaning fluids, or chemical-
impregnated wiping cloths.
Saving data
Some of the data of this instrument (page 32)
are retained when the power is turned off.
However, the saved data may be lost due to
some failure, an operation mistake, etc.
Information
About copyrights
Copying of the commercially available
musical data including but not limited to MIDI
data and/or audio data is strictly prohibited
except for your personal use.
This product incorporates and bundles
contents in which Yamaha owns copyrights or
with respect to which Yamaha has license to
use others’ copyrights. Due to copyright laws
and other relevant laws, you are NOT allowed
to distribute media in which these contents
are saved or recorded and remain virtually
the same or very similar to those in the
product.
* The contents described above include a
computer program, Accompaniment Style
data, MIDI data, WAVE data, voice
recording data, a score, score data, etc.
* You are allowed to distribute medium in
which your performance or music
production using these contents is
recorded, and the permission of Yamaha
Corporation is not required in such cases.
About this manual
The illustrations and LCD screens as shown
in this manual are for instructional purposes
only, and may appear somewhat different
from those on your instrument.
The letters at the end of the model name (“B”
or “RD”) are color information of the
instrument. For example, “B” indicates
“black,” and “RD” indicates “red.” Since they
simply indicate the color, these letters are
omitted in this manual.
iPhone, iPad, iPod touch and Lightning are
trademarks of Apple Inc., registered in the
U.S. and other countries.
Android™ is a trademark of Google LLC.
IOS is a trademark or registered trademark of
Cisco in the U.S. and other countries and is
used under license.
The Bluetooth
®
word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by
Yamaha Corporation is under license.
The company names and product names in
this manual are the trademarks or registered
trademarks of their respective companies.
About Bluetooth
For information on handling Bluetooth
communications, refer to “About Bluetooth”
on pages 9 and 37.
SHS-500 Owner’s Manual 9
Compatible Formats
GM System Level 1
“GM System Level 1” is an addition to the MIDI standard which ensures that any GM-
compatible music data can be accurately played by any GM-compatible tone generator,
regardless of manufacturer.
About Bluetooth
Bluetooth capability
Depending on the country in which you purchased the product, the instrument may not have
Bluetooth capability. If the Bluetooth icon is displayed in the upper right corner of the display as
illustrated above, or the value “BLE MIDI” (Bluetooth MIDI) is selectable in the lower of the display,
this means that the product is equipped with Bluetooth functionality.
To confirm that the value “BLE MIDI” is selectable or not, press the [FUNCTION] button repeatedly
to call up the Function menu “MIDI Select” in the upper of the display, then rotate the [SELECT]
knob to select the value in the bottom of the display.
Keep in mind that it is only MIDI data, and not audio data, that can be received and transmitted by
this instrument via Bluetooth.
[FUNCTION] button
[SELECT] knob
Display
Function menu
Value
Bluetooth icon
Display
10 SHS-500 Owner’s Manual
Thank you for purchasing the keytar Yamaha Digital Keyboard!
The keytar not only lets you enjoy playing the keyboard—even strapped around your
shoulder like a guitar—but also gives you powerful tools for effortlessly playing along with
your favorite music, by connecting to the smart device app “Chord Tracker.”
We recommend that you read this manual carefully so that you can fully take advantage of
the advanced and convenient functions of the instrument.
We also recommend that you keep this manual in a safe and handy place for future
reference.
This instrument has the following documents and instructional materials.
Owner’s Manual (this book)
Explains how to get started with the instrument and how to use main feature
Jam function. For more detailed information, refer to online manual “Reference
Manual” below.
Reference Manual (Online Manual)
Provides more detailed information.
To obtain online manual (PDF), access the Yamaha Downloads website, then enter the
model name for searching the desired files.
Owner’s Manual x1
•AC Adaptor* x1
•Strap x1
MIDI breakout cable x1
Online Member Product Registration x1
* May not be included depending on your particular area. Please check with your Yamaha dealer.
About the Manuals
Yamaha Downloads
https://download.yamaha.com/
Included Accessories
SHS-500 Owner’s Manual 11
Contents
Features .............................................................................................................. 11
Functions of Panel Components ..................................................................... 12
Setting Up ........................................................................................................... 16
Try Playing a Variety of Instrument Voices ..................................................... 21
Enjoy Playing with the Jam Function............................................................... 23
Backup and Initialization ................................................................................... 32
Troubleshooting ................................................................................................. 33
Specifications ..................................................................................................... 34
Index .................................................................................................................... 36
Features
Amazingly easy and powerful performance functions .......................... page 23
With the Jam Function, you can instantly enjoy playing along with your favorite songs. Simply connect
the instrument with the free app “Chord Tracker” and play along with songs stored to your smart
device. No matter which keys you press, the notes automatically match the song, so you don’t have to
worry about fingering or even knowing the proper scales and chords. You can simply lose yourself in
the performance, just as if you were jamming with your favorite artist.
For information on devices that are compatible with “Chord Tracker,” check the Yamaha website.
Control interface for authentic playing ........................................... pages 15, 22
In addition to a Pitch Bend wheel and Modulation wheel, the instrument also features knobs that let
you control a wide range of effects, giving you extraordinarily expressive, dynamic performance
power.
Slim and ultra-lightweight body
An ultralight body weighing only 1.5 kg and slim form make the instrument easily portable. It can also
be used on battery power, letting you enjoy playing anywhere you want.
12 SHS-500 Owner’s Manual
Functions of Panel Components
DC IN jack (page 17)
For connecting the AC adaptor.
[VOLUME] dial (page 19)
For adjusting the overall volume.
[ ] (Standby/On) switch (page 19)
For turning the power on or setting it to standby.
[LINE OUT] jack (1/4" mono phone)
For connecting a powered speaker or a mixing console for playing in larger venues at higher
volumes (with 1/4" mono phone plug). To control the LINE OUT volume, adjust the volume of the
connected audio equipment.
NOTICE
To avoid possible damage, first turn on the power to the instrument, then to the external device. When
turning off the power, first turn off the power to the external device, then to the instrument.
[AUX IN] jack (3.5 mm, mini stereo phone)
For inputting the sound of an audio player and listening to it through the built-in speaker of the
instrument (with 3.5 mm, mini stereo phone plug). To adjust the input volume from [AUX IN] jack,
adjust the audio playback volume on the audio device.
NOTICE
To avoid damage to the devices, first turn on the power to the external device, then to the instrument.
When turning off the power, first turn off the power to the instrument, then to the external device.
(Bottom of the unit)
SHS-500 Owner’s Manual 13
[TO HOST] terminal (page 28)
For connecting a computer or a smart device by using a USB cable, in order to transmit/receive
MIDI data or audio data (using the USB audio interface function). For details on the USB audio
interface function, refer to the “Reference Manual.” When transmitting/receiving MIDI data, you
may need to call up the Function settings (see “MIDI transmission/reception” below).
[MIDI] terminal
For connecting other MIDI devices via the included MIDI breakout cable and standard MIDI
cables (sold separately). When transmitting/receiving MIDI data, you may need to call up the
Function settings (see “MIDI transmission/reception” below).
[SELECT] knob (page 21)
For selecting a Voice to play on the keyboard. The selected Voice name will be shown in the
display.
While the [FUNCTION] button indicator is lit, this knob works as a value selector for the Function.
[EFFECT] selector (page 22)
For selecting the effect which is applied to the Voice. This selector is used in conjunction with the
[EFFECT CONTROL] knob.
[EFFECT CONTROL] knob (page 22)
For setting the value of the effect which is selected by [EFFECT] selector. Turning the knob
clockwise increases the depth of the effect.
MIDI transmission/reception
Make sure to match the MIDI transmit/receive port as well as the value of the Function “MIDI Select” setting. Press the
[FUNCTION] button repeatedly to call up “MIDI Select” at the top of the display, then rotate the [SELECT] knob to
select an appropriate value at the bottom: “BLE MIDI” (Bluetooth), “USB MIDI” (TO HOST) or “MiniMIDI” (MIDI).
Connection example
Connect to your smart device by Bluetooth or by the USB cable. Confirm Bluetooth availability on
page 9, and then refer to pages 27 and 28.
SHS-500
PHONES
MIDI
MIDI IN
MIDI OUT
TO HOST
LINE OUT
AUX IN
Smart device
Headphones
Audio player
Powered speaker
MIDI device
MIDI breakout cable
PC
MIDI OUT
terminal
MIDI IN
terminal
14 SHS-500 Owner’s Manual
Display
Current settings are shown in the display.
[PHONES] jack
For connecting a pair of stereo headphones with a mini stereo phone plug (3.5 mm). The
instrument’s built-in speakers automatically stop producing sound when headphones are
connected to this jack. However, the [LINE OUT] jack will continue to output the same sound as
the [PHONES] jack.
CAUTION
To prevent hearing loss, avoid using headphones at high volumes for extended periods of time.
[OCTAVE] buttons [-][+]
For shifting the pitch of the keyboard up or down by one octave. Pressing simultaneously resets to
the default setting. The current setting is shown in the display.
[TRANSPOSE] buttons [-][+]
For transposing the pitch of the keyboard up or down (in semitones). Pressing simultaneously
resets to the default setting. The current setting is shown in the display.
Normally indicates the Voice name
Transpose
T-1: down in semitone units
T±0: no change in pitch
T+1: up in semitone units
Octave
O-1: 1 octave down
O±0: no change in pitch
O+1: 1 octave up
MIDI Select
USB connection
MIDI connection
Power
(Adaptor or remaining battery
power indication)
Bluetooth connection
SHS-500 Owner’s Manual 15
[ ] (Fast Reverse), [ / ] (Play/Pause), [ ] (Fast Forward)
When not connected to app: These are playback control buttons for the internal demo songs
(page 24).
When connected to app “Chord Tracker”: These are playback control buttons for the app to
play/pause a song in the smart device (page 29).
[JAM] button (page 29)
With each button press, this turns the Jam function on (indicator lights), selects the Jam mode in
order, and then turns off the Jam function (indicator goes off).
[SUSTAIN] button
While holding down this button, the notes you play have a longer sustain.
[PITCH] bend wheel
For adding smooth pitch variations to notes you play on the
keyboard. Roll the wheel upward to raise the pitch, or downward to
lower the pitch.
[MODULATION] wheel
For applying a vibrato effect to notes played on the keyboard. Roll
the wheel upward to increase the effect depth, or downward to
minimize it. The [MODULATION] wheel can also be used to control the effect depth in the same
way as the [EFFECT CONTROL] knob ( ), if you set it via the Function mode. For the operation,
see the NOTE at the bottom of page 22.
[FUNCTION] button
Enter the Function mode (indicator lights). The Function mode enables you to set various settings
such as Tuning and MIDI channel selection. For details, refer to the online manual “Reference
Manual” described on page 10.
How to set: Press the [FUNCTION] button repeatedly to call up the desired Function menu in the
upper of the display, then rotate the [SELECT] knob ( ) to select its value in the bottom of the
display.
To exit from the Function mode, press [EXIT] button ( ) (indicator goes off).
NOTE
The last Function setting selected here is conveniently memorized when you exit the Function mode and
automatically recalled when you re-enter the mode.
[EXIT] button
Exits from the Function mode.
Function name
Value
16 SHS-500 Owner’s Manual
Setting Up
Attach the included strap securely to the strap pins of the instrument as illustrated below.
Since the strap has an adjuster, you can adjust the strap as you like.
CAUTION
This strap is designed for use with only this instrument. Do not use for any other purpose.
When using a strap, make sure the strap is securely attached to the instrument.
Do not lift the instrument by the strap. Doing so can cause damage to the instrument or injury.
Never loosen the screws mounting the strap pins.
Attach the Strap
Adjuster
SHS-500 bottom
Strap pin
Strap
SHS-500 Owner’s Manual 17
This instrument can be powered by either an AC adaptor or batteries.
Using an AC Adaptor
Connect the AC adaptor in the order shown in the illustration.
WARNING
Use the specified AC adaptor (page 35) only. Using the wrong AC
adaptor can result in damage to the instrument or overheating.
When using the AC adaptor with a removable plug, make sure to keep
the plug attached to the AC adaptor. Using the plug alone can cause
electric shock or fire.
Never touch the metallic section when attaching the plug. To avoid
electric shock, short circuit or damage, also be careful that there is no
dust between the AC adaptor and plug.
CAUTION
When setting up the product, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn
the power off and disconnect the plug from the outlet.
NOTE
Follow the order shown above in reverse when disconnecting the AC adaptor.
Power Requirements
1.
2.
DC IN jack
Bottom of the instrument
AC outlet
AC adaptor
18 SHS-500 Owner’s Manual
Using Batteries
This instrument requires six “AA” size, Alkaline (LR6)/ Manganese (R6) batteries, or rechargeable
nickel-metal hydride batteries (rechargeable Ni-MH batteries).
1. Make sure that the power of the instrument is off.
2. Open the battery compartment cover located on the instrument’s bottom panel.
3. Insert the six new batteries, being careful to follow the polarity markings on the
inside of the compartment.
4. Replace the compartment cover, making sure that it locks firmly in place.
NOTICE
Connecting or disconnecting the power adaptor with batteries installed may turn the power off,
resulting in loss of data.
When battery power becomes too low for proper operation, the volume may be reduced, the sound
may be distorted, and other problems may occur. When this happens, make sure to replace all
batteries with new ones or already recharged ones.
NOTE
This instrument cannot be used to charge the batteries. Use only the specified charger device when
charging.
Power will be automatically drawn from the AC adaptor if an AC adaptor is connected while batteries are
installed in the instrument.
Setting the battery type
Depending on the battery type to be used, you may need to change the battery type setting on this
instrument. To change the setting, first turn on the power to the instrument, then choose the battery
type you would like to use. Alkaline and manganese batteries are chosen by default. Press the
[FUNCTION] button repeatedly to select “Battery,” then rotate the [SELECT] knob to select the
battery type “Alkaline” (Alkaline and manganese batteries) or “Ni-MH” (rechargeable Ni-MH
batteries).
NOTICE
Failure to set the battery type may shorten the amount of the battery life. Make sure to set the battery type
correctly.
SHS-500 Owner’s Manual 19
1. Turn down the [VOLUME] dial to the minimum.
2. Press the [ ] (Standby/On) switch to turn the power on.
The product name appears in the display, followed by the normal display.
Adjust the volume as desired while playing the keyboard.
CAUTION
Do not use the instrument or headphones for a long period of time at a high or uncomfortable volume
level, since this can cause permanent hearing loss.
NOTICE
While turning on the power, do not attempt any other operations, such as pressing the keys. Doing so
may cause the instrument to malfunction.
3. Press and hold the [ ] (Standby/On) switch for about a second to turn the power
off.
CAUTION
Even when the power switch is turned off, electricity is still flowing to the product at the minimum level.
When you are not using the product for a long time, make sure to unplug the power cord from the wall AC
outlet.
Turning the Power On/Standby
If the overall volume is low, or no sound is heard, please confirm “Troubleshooting” on page 33
1.
2.
Maximum
Minimum
Power On
Turn the Volume to minimum
Display
20 SHS-500 Owner’s Manual
Power status
You can confirm the power source at the right corner of the display.
Setting the Auto Power Off function
To prevent unnecessary power consumption, this instrument features an Auto Power Off function that
automatically turns the power off if the instrument is not operated for a specified period of time. The
amount of time that elapses before the power is automatically turned off is 30 minutes by default;
however, you can change the setting via Function (For details, refer to the Reference Manual).
Disabling Auto Power Off
1. When the instrument is turned on, turn off the power.
2. Turn the power on while holding down the lowest key on the keyboard.
A message “AutoOff Disabled” appears briefly.
Enabling Auto Power Off
To enable the Auto Power Off function, change the setting via the Function mode or initialize the
instrument (page 32).
NOTICE
Some of the data of this instrument (page 32) are retained when the power is turned off.
If your instrument is connected to other equipment such as amplifiers and speakers but you do not intend
to use it for 30 minutes, we recommend that you turn off all devices as described in their owner’s manuals.
Doing so eliminates the risk of damage to the other equipment. If you do not want the instrument to turn off
automatically when connected to other equipment, disable the Auto Power Off function.
AC adaptor Batteries: full Batteries: half
Replace soon.
Batteries: low
Power will turn off.
SHS-500 Owner’s Manual 21
Try Playing a Variety of Instrument Voices
You can change the keyboard Voice to another instrument Voice, such as strings, electric piano and
others.
NOTE
If the [FUNCTION] button is lit, turn it off by pressing the [EXIT] button, since the [SELECT] knob behavior varies
depending on whether the [FUNCTION] button is lit or not.
1. Rotate the [SELECT] knob.
You can see the selected Voice name on the display.
NOTE
For a list of the available Voices, refer to the Reference Manual.
Selecting and Playing a Voice
22 SHS-500 Owner’s Manual
The effects enhance the Voice and change the touch sensitivity of the keyboard.
1. Select the desired effect with the [EFFECT] selector.
2. Change the depth of the selected effect by
rotating the [EFFECT CONTROL] knob.
Turning the knob clockwise increases the amount of
effect depth. When the knob is turned all the way
counter-clockwise, no effect is applied to the sound.
Selecting another Voice resets the effect depth value
you have set.
The DSP effect type can be selected by the Function. To do this, press the [FUNCTION] button
repeatedly to call up the Function menu “DSP Type” in the upper part of the display, then rotate
the [SELECT] knob to select the desired type in the bottom part of the display. To exit from the
Function mode, press the [EXIT] button (indicator goes off). For details on the DSP types, refer to
the online manual “Reference Manual.”
NOTE
The [EFFECT CONTROL] knob function can be conveniently assigned to the [MODULATION] wheel (page 15)
so that you can enhance or change the effect in real time, using the [MODULATION] wheel with your left hand
while playing the keyboard with your right. To do this, press the [FUNCTION] button repeatedly to call up the
Function menu “Modulation” in the upper of the display, then rotate the [SELECT] knob to select “EfctCtrl” in the
bottom of the display.
Apply Effects
FILTER
Changes the character of the
sound.
DYNAMICS
Sets the touch sensitivity of the
keyboard.
Lower values produce greater
volume variation in response to
keyboard dynamics—in other
words, providing greater
sensitivity and making it easier to
produce wide dynamic changes.
Higher values produce a more
uniform response—in other words,
providing less sensitivity and
making it easier to produce loud
sounds in your performance.
REVERB
Adding reverb
CHORUS
Adding chorus
OTHER
Adjusts the parameters of the DSP
effect selected by the Function.
In the default setting, the optimum
DSP type for the selected Voice is
automatically called up.
SHS-500 Owner’s Manual 23
Enjoy Playing with the Jam Function
This incredibly cool and powerful performance feature lets you play along with songs stored on a
smart device, using the smart device app “Chord Tracker.” No matter which keys you press, the notes
automatically match the song, so you don’t have to worry about fingering or even knowing the proper
scales and chords!
About the Jam Function
J Fnci
Jam and perform
along with your
favorite song!
Try out the Jam function now, and
have fun with it—it’s an amazingly
easy way to perform music,
allowing you to instantly play in
any key and in any style!
Before you dive in though, you
really should find out more about
the various Jam features and
operations to get the most out of
the instrument. So, go on to the
next few pages, using the preset
demo songs to play with the Jam
function.
24 SHS-500 Owner’s Manual
The preset demo songs let you fully experience the Jam function—without the need to connect to the
smart device app—by automatically activating the Jam function and selecting the suitable Jam mode.
Simply START playback of a demo song and have fun playing along with it!
Selecting a Demo Song
Three demo songs are provided for selecting by pressing the [ / ] (Play/Pause) button (the
indicator flashes). Selecting a demo song automatically activates the Jam mode and starts repeat
playback of all the songs. The name of the demo song will be shown in the display.
To stop playback, press the [ / ] (Play/Pause) button repeatedly until the indicator goes off.
Playing along with a Demo Song
Demo Song: TryAcmp1
Recommended Voice: 001 SawLead1, Jam mode: Backing
Jam mode “Backing” is automatically selected (page 30).
This mode is ideal for playing backing. Play along with the demo song!
Playing backing along with the demo
Before you start out, try to feel the rhythm of the song. Then play a chord in time with the music.
You can play any key.
How does it sound? Thanks to the powerful Jam functions, you can get amazingly musical results
no matter where you play! Try playing chords up and down the keyboard and with different
rhythmic accents.
Experience the Jam Function
TryAcmp1
TryMeldy
TryAcmp2
Demo OFF
Demo 1
Demo 2
Demo 3
Stop
[ / ] (Play/Pause)
[ ] (Fast Reverse)
[ ] (Fast Forward)
Once you get a feel for it, try playing chords
changing the key position!
SHS-500 Owner’s Manual 25
Demo Song: TryMeldy
Recommended Voice: 006 UnderHeim, Jam mode: Melody B
Jam mode “Melody B” is automatically selected (page 30).
This mode is ideal for playing melodies.
Playing melodies along with the demo
Play one note at a time with your fingers in sequence (for example: thumb middle finger little
finger). Try creating interesting ad-lib phrases, and enjoy consistently beautiful musical results!
Demo Song: TryAcmp2
Recommended Voice: 009 E.Piano, Jam mode: 1 Finger
Jam mode “1 Finger” is automatically selected (page 30).
This mode is ideal for playing backing in the same way as the “Backing” mode—except that it
adds harmonies to the notes played on the keyboard, so that you can play full backing parts with
even just one finger.
Playing backing along with the demo
To turn off the Jam function, press the [JAM] button repeatedly until the indicator goes off.
Tip
Watch the display during playback and you will see marks such as “C m7”
shown in sequence along with song playback. These indicate the chords
used in the song. Since the chords of a song constantly change, different
notes and chords will be produced even if you repeatedly play the same
keys in the Jam mode. (Depending on the chord succession, notes may not be changed.) Once
you get a feel for it, match your playing rhythm to that of the chord change timing shown in the
display, and add professional sounding backing to the song.
Just a single key produces two or more notes.
26 SHS-500 Owner’s Manual
Now, let’s play along with a song stored in a smart device. Download the app “Chord Tracker” and
connect your keyboard to the app via Bluetooth or a USB cable.
Downloading App
Download the free app “Chord Tracker” (iOS/Android).
Chord Tracker (free)
This app corresponds to iOS and Android devices. For information on release dates and the latest
system requirements, see the website below.
https://www.yamaha.com/kbdapps/
Playing Along with a Favorite Song
Download app
Connect your keyboard to app
via Bluetooth or USB cable
Play with app
SHS-500 Owner’s Manual 27
Bluetooth Connection
NOTE
If your keyboard is not equipped with Bluetooth functionality or Bluetooth is not available for some reason, you can
connect to this app with a USB cable. For details on USB connections, see the next page.
1. Turn the power to the instrument to on.
2. Activate the Bluetooth function of the smart device.
3. Start the app “Chord Tracker” and tap the “Setting” “Bluetooth MIDI Device”
“SHS-500”.
When connection is done successfully, “Connected” is shown.
* All screen captures are from iPhone.
If the instrument cannot be connected to the app via Bluetooth, refer to “Troubleshooting” on
page 33.
Check if your keyboard is equipped with Bluetooth functionality; refer to page 9.
28 SHS-500 Owner’s Manual
USB Cable Connection
1. Turn off the power of the instrument, then connect your smart device to the
instrument.
For the proper order, carefully follow the indicated instruction steps as illustrated above.
The necessary items for this connection differ depending on your smart device as illustrated
above. They are separately sold items.
NOTICE
Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used.
2. Turn on the instrument.
3. Change the setting of the instrument from Bluetooth to [TO HOST] terminal.
Press the [FUNCTION] button repeatedly to call up the Function menu “MIDI Select” in the upper
of the display, then rotate the [SELECT] knob to select the value “USB MIDI” in the bottom of the
display. If you want to connect to the “Chord Tracker” app with Bluetooth, restore the value to
“BLE MIDI.”
TO HOST
USB (B) USB (A)
If the device’s connector is USB Micro B:
Use a USB Type A female - USB Micro B male
conversion adaptor
If the device’s connector is USB Type C:
Use a USB Type A female - USB Type C male
conversion adaptor
USB cable
Lightning to USB
Camera Adapter
USB conversion adaptor
iOS device
Android
device
SHS-500 Owner’s Manual 29
Playing with App
1.
Connect the keyboard and the app via Bluetooth or a USB cable in advance. Refer
to pages 27 and 28.
2. Start the app “Chord Tracker” then select a song.
The app automatically begins analysis of the selected song then displays the detected chord data
on your smart device like below.
NOTE
Chord Tracker can analyze chord data with a high degree of accuracy, but in some cases, the detected chord
progression may differ from that of the original song.
3. Turn the Jam function on.
4. Select a Jam mode.
As five Jam modes are provided (next page), select one matching the style you want to play.
Pressing the [JAM] button repeatedly selects modes in sequence. The selected mode name is
shown in the display.
[JAM] button
30 SHS-500 Owner’s Manual
Jam modes
* When you want to play melodic parts on a keyboard, the app Chord Tracker’s “Melody Cancellation” function
may be useful because the function suppresses the vocal part of the song. For this operation, refer to the
included manual within the app.
5. Play back a song.
Use [ ] (Fast Reverse), [ / ] (Play/Pause) and [ ] (Fast Forward) buttons to control the
song on the app.
When connected with Bluetooth, the song sounds from the smart device.
When connected with a USB cable, the song sounds from the keyboard.
NOTE
As soon as song playback begins, the app starts transmitting the chord information to the keyboard as MIDI
data. Both the chord information and the selected Jam mode determine the sound which is produced when the
keys are pressed.
1 Finger
You can play backing parts even with just one finger.
An example using a preset demo song is given on page 25.
Backing
Ideal for playing backing parts.
An example using a preset demo song is given on page 24.
Melody A
Ideal for playing the melodies.
Try these modes in order: A B C to find the most suitable one matching the
style.
An example using “Melody B” with a preset demo song is given on page 25.
Melody B
Melody C
Off
Turn the Jam function off.
Volume setting
When you want to adjust the volume balance between the song playback and your keyboard
performance, adjust the volume on your smart device. If further adjustment seems
necessary, change the Function “EQ Type” setting (overall sound). Press the [FUNCTION]
button repeatedly to call up “EQ Type” at the top of the display, then rotate the [SELECT]
knob to select the value at the bottom.
When connected with a USB cable, the keyboard may produce sound even when the
volume on smart device is set to minimum.
Smart device
Play
Fast reverse Fast forward
SHS-500 Owner’s Manual 31
6. Play along with a rhythm of the song.
Play professional sounding backing parts or
melodies according to the selected Jam mode!
Also, refer to pages 24 and 25 for how to get the
most enjoyment from the Jam function.
7. Finish your performance.
You can stop playback at any time by pressing the [ / ] (Play/Pause) button. Also, press the
[JAM] button several times to turn off the Jam function (unlit) and close the app on the smart
device.
NOTICE
The demo songs will not be played back correctly if you disconnect the Bluetooth or pull out the USB
cable without closing the app, because this interrupts the link between the app and the instrument.
NOTE
For details on how to use this app, refer to the app manual.
Transpose cannot be used during the Jam mode.
Using headphones
When connected with Bluetooth, you may want to hear the sound from the smart device
and the keyboard with the headphones. In this case, connect the [AUX IN] jack of the
instrument and the headphone jack of the smart device with audio cable.
Smart device
Pause
Close
app
JAM
(Unlit)
32 SHS-500 Owner’s Manual
Backup and Initialization
The following data will automatically be maintained as backup data even if you turn off the power.
Function Settings:
Tuning
•EQ Type
MIDI Select (specific terminal used for MIDI data transmit/receive; page 13, “MIDI transmission/
reception”)
MIDI CH (MIDI channel)
LoopBack (Audio Loop Back on/off setting)
Battery (battery type; page 18)
Auto Off (Auto Power Off; page 20)
* For explanations on items above which have no corresponding page references, refer to the online manual
“Reference Manual.”
NOTICE
Backup is executed automatically when the power is turned off. When the power is turned off in the following
cases, backup is not executed.
Disconnected AC adaptor
Power failure
Low or no battery power
You can initialize the backup data.
1. Turn the power of the keyboard off.
2. While holding down the highest key, turn the power on to initialize the backup
data to the factory initial settings.
When initialization is finished, “Backup Clear” appears in the bottom of the display.
Backup Parameters
Initialization
SHS-500 Owner’s Manual 33
Troubleshooting
Q. The overall volume is low, or no sound is heard.
A. Raise the master Volume with the [VOLUME] dial. Or raise the touch sensitivity of the keyboard by
rotating the [EFFECT CONTROL] knob clockwise (DYNAMICS; page 22). Or adjust the filter value:
first select “FILTER” with selector, then adjust its value with the [EFFECT CONTROL] knob.
Q. The instrument cannot be connected to the app via Bluetooth.
A. Check that the Bluetooth function of the smart device is activated. Or initialize the keyboard
(page 32) so that the value of the Function menu “MIDI Select” is reset to “BLE MIDI” (Bluetooth).
Then try connecting again.
Q. The instrument cannot be connected to the app via USB cable.
A. Check that the value of the Function menu “MIDI Select” is set to “USB MIDI” as described on
page 28, step 3. Then try connect again.
Q. Vibrato is added to the sound.
A. Check that the [MODULATION] wheel is set to the appropriate position. Roll the wheel downward
so that the vibrato effect is not added.
Q. MIDI data cannot be transmitted/received.
A. Set the Function according to the terminal or function to be used. For instructions, refer to “MIDI
transmission/reception” on page 13.
Q. The demo song does not play back when the [ / ] button is pressed.
A. Turn the [ ] (Standby/On) switch off and turn it on again. Then try the operation again.
For other problems, refer to the Troubleshooting section in the online manual “Reference Manual.”
34 SHS-500 Owner’s Manual
Specifications
Product Name Digital Keyboard
Voices AWM Stereo Sampling
Polyphony (Max.) 48
Number of Voices 30
Compatibility GM
Effects Reverb, Chorus, DSP 9 types
Demo Preset 3 Songs
Functions JAM Yes (5 mode)
Overall Controls Tuning, Modulation, Pitch bend range, Portamento,
DSP, MIDI select, Transpose, Octave shift, USB audio
interface (44.1 kHz, 16 bit, stereo)
Bluetooth
*This function may not
be included
depending on the
country in which you
purchased the
product. Refer to
page 9 for details.
Bluetooth (Ver 4.0 GATT)
Comply with Bluetooth Low Energy MIDI Specification
Range of transmit frequency: 2402 – 2480 MHz
Maximum RF output power (E.I.R.P): 4 dBm
Control
Interface
Keyboard 37 HQ (High Quality) Mini Keys
Other Controllers PITCH bend wheel, MODULATION wheel,
TRANSPOSE button, OCTAVE button, RWD button,
PLAY/PAUSE button, FF button, SUSTAIN button,
EFFECT CONTROL knob, SELECT knob,
EFFECT selector
Display LCD with backlight
Connectivity [AUX IN] (3.5 mm, mini stereo phone jack),
[LINE OUT] (1/4" mono phone plug),
[PHONES] (3.5 mm, mini stereo phone jack),
[TO HOST], [MIDI] (mini-DIN IN/OUT), [DC IN]
Sound System Amplifier: 0.7 W
Speaker: 3.6 cm
SHS-500 Owner’s Manual 35
The contents of this manual apply to the latest specifications as of the publishing date. To obtain the
latest manual, access the Yamaha website then download the manual file. Since specifications,
equipment or separately sold accessories may not be the same in every locale, please check with
your Yamaha dealer.
Power Supply Power Supply PA-130 or an equivalent recommended by Yamaha
Six “AA” size alkaline (LR6), manganese (R6) or
Ni-MH rechargeable (HR6) batteries
Power
Consumption
3W (When using PA-130 AC adaptor)
Auto Power Off Yes
Size (W x D x H)/Weight 821 mm x 121 mm x 65 mm (32-5/16" x 4-3/4" x 2-9/16"),
1.5 kg (3 lb, 5 oz) (not including batteries)
Included Accessories AC adaptor*, Strap, MIDI breakout cable, Owner’s
Manual, Online Member Product Registration
*May not be included depending on your area. Check with your
Yamaha dealer.
Separately Sold Accessories
(May not be available depending on your
area.)
Keyboard Bag (SC-KB350),
Headphones (HPH-150, HPH-100, HPH-50)
36 SHS-500 Owner’s Manual
Index
[ ] (Fast Reverse) .......................... 15, 24, 30
[ / ] (Play/Pause) ............................ 15, 24, 30
[ ] (Fast Forward) .......................... 15, 24, 30
A
AC adaptor ..................................................... 17
App ........................................................... 26, 29
Auto Power Off ................................................ 20
[AUX IN] jack .................................................. 12
B
Backup ........................................................... 32
Battery ............................................................ 18
Bluetooth ........................................................... 9
Bluetooth connection ...................................... 27
C
Chord Tracker ................................................. 26
CHORUS ......................................................... 22
Connection ..................................................... 13
D
DC IN jack ...................................................... 17
Demo song ..................................................... 24
Display ............................................................ 14
DYNAMICS ..................................................... 22
E
Effect ............................................................... 22
[EFFECT CONTROL] knob ............................. 22
[EFFECT] selector ........................................... 22
[EXIT] button ................................................... 15
F
FILTER ............................................................ 22
[FUNCTION] button ........................................ 15
H
Headphones ............................................. 14, 31
I
Initialization ..................................................... 32
J
[JAM] button ...................................................15
Jam function .............................................23, 29
Jam modes .....................................................30
L
[LINE OUT] jack ..............................................12
M
[MIDI] terminal ................................................13
[MODULATION] wheel ...................................15
O
Octave ............................................................ 14
[OCTAVE] buttons ..........................................14
Online manual .................................................10
OTHER ............................................................ 22
P
[PITCH] bend wheel .......................................15
Power requirement ..........................................17
R
Reference Manual ........................................... 10
REVERB .......................................................... 22
S
[SELECT] knob ...............................................21
Specifications ................................................. 34
Strap ............................................................... 16
[SUSTAIN] button ...........................................15
T
[TO HOST] terminal ........................................13
Transpose .......................................................14
[TRANSPOSE] buttons ....................................14
Troubleshooting ..............................................33
U
USB cable connection .................................... 28
V
Voice ............................................................... 21
Volume ................................................ 12, 19, 30
SHS-500 Owner’s Manual 37
Bluetooth is a technology for wireless communication between devices within an area of about
10 meters (33 ft.) employing the 2.4 GHz frequency band.
Handling Bluetooth communications
The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of
equipment. While Bluetooth compatible devices use a technology minimizing the influence of other
components using the same radio band, such influence may reduce the speed or distance of
communications and in some cases interrupt communications.
The speed of signal transfer and the distance at which communication is possible differs according
to the distance between the communicating devices, the presence of obstacles, radio wave
conditions and the type of equipment.
Yamaha does not guarantee all wireless connections between this unit and devices compatible with
Bluetooth function.
For U.S.A.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has
very low levels of RF energy that is deemed to comply without testing of specific absorption
rate(SAR).
38 SHS-500 Owner’s Manual
For EU countries
BG Bulgarian
ОПРОСТЕНА ЕС ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ
С настоящото Yamaha Music Europe GmbH декларира, че този тип радиосъоръжение
[SHS-500] е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията
за съответствие може да се намери на следния интернет адрес:
https://europe.yamaha.com/en/support/compliance/doc.html
ES Spanish
DECLARACIÓN UE DE CONFORMIDAD SIMPLIFICADA
Por la presente, Yamaha Music Europe GmbH declara que el tipo de equipo radioeléctrico
[SHS-500] es conforme con la Directiva 2014/53/UE. El texto completo de la declaración UE
de conformidad está disponible en la dirección Internet siguiente:
https://europe.yamaha.com/en/support/compliance/doc.html
CS Czech
ZJEDNODUŠENÉ EU PROHLÁŠENÍ O SHODĚ
Tímto Yamaha Music Europe GmbH prohlašuje, že typ rádiového zařízení
[SHS-500] je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o
shodě je k dispozici na této internetové adrese:
https://europe.yamaha.com/en/support/compliance/doc.html
DA Danish
FORENKLET EU-OVERENSSTEMMELSESERKLÆRING
Hermed erklærer Yamaha Music Europe GmbH, at radioudstyrstypen [SHS-500] er i
overensstemmelse med direktiv 2014/53/EU. EU-overensstemmelseserklæringens
fulde tekst kan findes på følgende internetadresse:
https://europe.yamaha.com/en/support/compliance/doc.html
DE German
VEREINFACHTE EU-KONFORMITÄTSERKLÄRUNG
Hiermit erklärt Yamaha Music Europe GmbH, dass der Funkanlagentyp [SHS-500]
der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU-
Konformitätserklärung ist unter der folgenden Internetadresse verfügbar:
https://europe.yamaha.com/en/support/compliance/doc.html
ET Estonian
LIHTSUSTATUD ELI VASTAVUSDEKLARATSIOON
Käesolevaga deklareerib Yamaha Music Europe GmbH, et käesolev raadioseadme
tüüp [SHS-500] vastab direktiivi 2014/53/EL nõuetele. ELi vastavusdeklaratsiooni
täielik tekst on kättesaadav järgmisel internetiaadressil:
https://europe.yamaha.com/en/support/compliance/doc.html
EL Greek
ΑΠΛΟΥΣΤΕΥΜΕΝΗ ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ΕΕ
Με την παρούσα ο/η Yamaha Music Europe GmbH, δηλώνει ότι ο ραδιοεξοπλισμός
[SHS-500] πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο της δήλωσης
συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο:
https://europe.yamaha.com/en/support/compliance/doc.html
EN English
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Yamaha Music Europe GmbH declares that the radio equipment type
[SHS-500] is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address:
https://europe.yamaha.com/en/support/compliance/doc.html
FR French
DECLARATION UE DE CONFORMITE SIMPLIFIEE
Le soussigné, Yamaha Music Europe GmbH, déclare que l'équipement radioélectrique du
type [SHS-500] est conforme à la directive 2014/53/UE. Le texte complet de la déclaration
UE de conformité est disponible à l'adresse internet suivante:
https://europe.yamaha.com/en/support/compliance/doc.html
HR Croatian
POJEDNOSTAVLJENA EU IZJAVA O SUKLADNOSTI
Yamaha Music Europe GmbH ovime izjavljuje da je radijska oprema tipa
[SHS-500] u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o
sukladnosti dostupan je na sljedećoj internetskoj adresi:
https://europe.yamaha.com/en/support/compliance/doc.html
IT Italian
DICHIARAZIONE DI CONFORMITÀ UE SEMPLIFICATA
Il fabbricante, Yamaha Music Europe GmbH, dichiara che il tipo di apparecchiatura
radio [SHS-500] è conforme alla direttiva 2014/53/UE. Il testo completo della
dichiarazione di conformità UE è disponibile al seguente indirizzo Internet:
https://europe.yamaha.com/en/support/compliance/doc.html
LV Latvian
VIENKĀRŠOTA ES ATBILSTĪBAS DEKLARĀCIJA
Ar šo Yamaha Music Europe GmbH deklarē, ka radioiekārta [SHS-500] atbilst Direktīvai
2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē:
https://europe.yamaha.com/en/support/compliance/doc.html
LT Lithuanian
SUPAPRASTINTA ES ATITIKTIES DEKLARACIJA
Aš, Yamaha Music Europe GmbH, patvirtinu, kad radijo įrenginių tipas
[SHS-500] atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos
tekstas prieinamas šiuo interneto adresu:
https://europe.yamaha.com/en/support/compliance/doc.html
HU Hungarian
EGYSZERŰSÍTETT EU-MEGFELELŐSÉGI NYILATKOZAT
Yamaha Music Europe GmbH igazolja, hogy a [SHS-500] típusú
rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU-megfelelőségi
nyilatkozat teljes szövege elérhető a következő internetes címen:
https://europe.yamaha.com/en/support/compliance/doc.html
NL Dutch
VEREENVOUDIGDE EU-CONFORMITEITSVERKLARING
Hierbij verklaar ik, Yamaha Music Europe GmbH, dat het type radioapparatuur
[SHS-500] conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU-
conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres:
https://europe.yamaha.com/en/support/compliance/doc.html
PL Polish
UPROSZCZONA DEKLARACJA ZGODNOŚCI UE
Yamaha Music Europe GmbH niniejszym oświadcza, że typ urządzenia radiowego
[SHS-500] jest zgodny z dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodności UE
jest dostępny pod następującym adresem internetowym:
https://europe.yamaha.com/en/support/compliance/doc.html
PT Portuguese
DECLARAÇÃO UE DE CONFORMIDADE SIMPLIFICADA
O(a) abaixo assinado(a) Yamaha Music Europe GmbH declara que o presente tipo de equipamento
de rádio [SHS-500] está em conformidade com a Diretiva 2014/53/UE. O texto integral da
declaração de conformidade está disponível no seguinte endereço de Internet:
https://europe.yamaha.com/en/support/compliance/doc.html
RO Romanian
DECLARAȚIA UE DE CONFORMITATE SIMPLIFICA
Prin prezenta, Yamaha Music Europe GmbH declară că tipul de echipamente radio
[SHS-500] este în conformitate cu Directiva 2014/53/UE. Textul integral al declarației
UE de conformitate este disponibil la următoarea adresă internet:
https://europe.yamaha.com/en/support/compliance/doc.html
SK Slovak
ZJEDNODUŠENÉ EÚ VYHLÁSENIE O ZHODE
Yamaha Music Europe GmbH týmto vyhlasuje, že rádiové zariadenie typu
[SHS-500] je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode
je k dispozícii na tejto internetovej adrese:
https://europe.yamaha.com/en/support/compliance/doc.html
SL Slovenian
POENOSTAVLJENA IZJAVA EU O SKLADNOSTI
Yamaha Music Europe GmbH potrjuje, da je tip radijske opreme [SHS-500]
skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na
voljo na naslednjem spletnem naslovu:
https://europe.yamaha.com/en/support/compliance/doc.html
FI Finnish
YKSINKERTAISTETTU EU-VAATIMUSTENMUKAISUUSVAKUUTUS
Yamaha Music Europe GmbH vakuuttaa, että radiolaitetyyppi [SHS-500] on
direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen
täysimittainen teksti on saatavilla seuraavassa internetosoitteessa:
https://europe.yamaha.com/en/support/compliance/doc.html
SV Swedish
FÖRENKLAD EU-FÖRSÄKRAN OM ÖVERENSSTÄMMELSE
Härmed försäkrar Yamaha Music Europe GmbH att denna typ av radioutrustning
[SHS-500] överensstämmer med direktiv 2014/53/EU. Den fullständiga texten till
EU-försäkran om överensstämmelse finns på följande webbadress:
https://europe.yamaha.com/en/support/compliance/doc.html
TR Turkey
BASİTLEŞTİRİLMİŞ AVRUPA BİRLİĞİ UYGUNLUK BİLDİRİMİ
İşbu belge ile, Yamaha Music Europe GmbH, radyo cihaz tipinin [SHS-500],
Direktif 2014/53/AB'ye uygunluğunu beyan eder. AB uyumu beyanının tam
metni aşağıdaki internet adresinden edinilebilir:
https://europe.yamaha.com/en/support/compliance/doc.html
SHS-500 Owner’s Manual 39
40 SHS-500 Owner’s Manual
LIMITED 1-YEAR WARRANTY ON
PORTABLE KEYBOARDS
(NP, PSRE, PSREW, PSRF, SHS, EZ, DGX230, DGX530, YPG AND YPT SERIES)
Thank you for selecting a Yamaha product. Yamaha products are designed and manufactured to provide a high level of defect-free
performance. Yamaha Corporation of America (“Yamaha”) is proud of the experience and craftsmanship that goes into each and every
Yamaha product. Yamaha sells its products through a network of reputable, specially authorized dealers and is pleased to offer you, the
Original Owner, the following Limited Warranty, which applies only to products that have been (1) directly purchased from Yamaha’s
authorized dealers in the fifty states of the USA and District of Columbia (the “Warranted Area”) and (2) used exclusively in the
Warranted Area. Yamaha suggests that you read the Limited Warranty thoroughly, and invites you to contact your authorized Yamaha
dealer or Yamaha Customer Service if you have any questions.
Coverage: Yamaha will, at its option, repair or replace the product covered by this warranty if it becomes defective, malfunctions or
otherwise fails to conform with this warranty under normal use and service during the term of this warranty, without charge for labor or
materials. Repairs may be performed using new or refurbished parts that meet or exceed Yamaha specifications for new parts. If
Yamaha elects to replace the product, the replacement may be a reconditioned unit. You will be responsible for any installation or
removal charges and for any initial shipping charges if the product(s) must be shipped for warranty service. However, Yamaha will pay
the return shipping charges to any destination within the USA if the repairs are covered by the warranty. This warranty does not cover
(a) damage, deterioration or malfunction resulting from accident, negligence, misuse, abuse, improper installation or operation or failure
to follow instructions according to the Owner’s Manual for this product; any shipment of the product (claims must be presented to the
carrier); repair or attempted repair by anyone other than Yamaha or an authorized Yamaha Service Center; (b) any unit which has been
altered or on which the serial number has been defaced, modified or removed; (c) normal wear and any periodic maintenance; (d)
deterioration due to perspiration, corrosive atmosphere or other external causes such as extremes in temperature or humidity; (e)
damages attributable to power line surge or related electrical abnormalities, lightning damage or acts of God; or (f) RFI/EMI
(Interference/noise) caused by improper grounding or the improper use of either certified or uncertified equipment, if applicable. Any
evidence of alteration, erasing or forgery of proof-of-purchase documents will cause this warranty to be void. This warranty covers only
the Original Owner and is not transferable.
In Order to Obtain Warranty Service: Warranty service will only be provided for defective products within the Warranted Area.
Contact your local authorized Yamaha dealer who will advise you of the procedures to be followed. If this is not successful, contact
Yamaha at the address, telephone number or website shown below. Yamaha may request that you send the defective product to a local
authorized Yamaha Servicer or authorize return of the defective product to Yamaha for repair. If you are uncertain as to whether a dealer
has been authorized by Yamaha, please contact Yamaha’s Service Department at the number shown below, or check Yamaha’s website
at www.yamaha.com. Product(s) shipped for service should be packed securely and must be accompanied by a detailed explanation
of the problem(s) requiring service, together with the original or a machine reproduction of the bill of sale or other dated, proof-of-
purchase document describing the product, as evidence of warranty coverage. Should any product submitted for warranty service be
found ineligible therefore, an estimate of repair cost will be furnished and the repair will be accomplished only if requested by you and
upon receipt of payment or acceptable arrangement for payment.
Limitation of Implied Warranties and Exclusion of Damages: ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE APPLICABLE PERIOD
OF TIME SET FORTH ABOVE. YAMAHA SHALL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE
OF USE OR INTERRUPTION OF PERFORMANCES OR ANY CONSEQUENCES. YAMAHA’S LIABILITY FOR ANY DEFECTIVE PRODUCT
IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, AT YAMAHA’S OPTION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. This Warranty gives you
specific legal rights, and you may also have other rights which vary from state to state. This is the only express warranty applicable to
the product specified herein; Yamaha neither assumes nor authorizes anyone to assume for it any other express warranty.
If you have any questions about service received or if you need assistance in locating an authorized Yamaha Servicer, please contact:
CUSTOMER SERVICE
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, California 90620-1373
Telephone: 800-854-1569
www.yamaha.com
Do not return any product to the above address without a written Return Authorization issued by YAMAHA.
© 2018 Yamaha Corporation of America.
SHS-500 Owner’s Manual 41
(weee_battery_eu_en_02)
Information for users on collection and disposal of old equipment and used
batteries:
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries should not be mixed with general household
waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them
to applicable collection points, in accordance with your national legislation.
By disposing of these products and batteries correctly, you will help to save valuable resources
and prevent any potential negative effects on human health and the environment which could
otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact
your local municipality, your waste disposal service or the point of sale where you purchased the
items.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier
for further information.
Information on Disposal in other Countries outside the European Union:
These symbols are only valid in the European Union. If you wish to discard these items, please
contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with
the requirement set by the EU Battery Directive for the chemical involved.
42 SHS-500 Owner’s Manual
MEMO
Yamaha Global Site
https://www.yamaha.com/
Yamaha Downloads
https://download.yamaha.com/
Manual Development Group
© 2018 Yamaha Corporation
Published 07/2018 MWES*.*-**A0
VAF5630
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Yamaha SHS-500 de handleiding

Type
de handleiding