Yamaha YDP-S54 de handleiding

Merk: Yamaha

Model: YDP-S54

Type: de handleiding

Deze handleiding is ook geschikt voor

Owner’s Manual

Mode d’emploi

Manual de instrucciones

Before using the instrument, be sure to read “PRECAUTIONS” on pages 5-6.

For information on assembling the instrument, refer to the instructions at the end of this

manual.

Avant d’utiliser l’instrument, lisez attentivement la section « PRÉCAUTIONS D’USAGE »

aux pages 5 et 6.

Pour plus d’informations sur l’assemblage de l’instrument, reportez-vous aux instructions

figurant à la fin de ce manuel.

Antes de utilizar el instrumento, lea las “PRECAUCIONES”, en las páginas 5-6.

Para obtener más información sobre el montaje del instrumento, consulte las

instrucciones que encontrará al final de este manual.

EnglishFrançaisEspañol

YDP

164

YDP

144

YDP

S54

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply

(adapter). DO NOT connect this product to any power supply

or adapter other than one described in the manual, on the

name plate, or specifically recommended by Yamaha.

WARNING:

Do not place this product in a position where

anyone could walk on, trip over, or roll anything over power or

connecting cords of any kind. The use of an extension cord is

not recommended! If you must use an extension cord, the

minimum wire size for a 25' cord (or less) is 18 AWG. NOTE:

The smaller the AWG number, the larger the current handling

capacity. For longer extension cords, consult a local

electrician.

This product should be used only with the components

supplied or; a cart, rack, or stand that is recommended by

Yamaha. If a cart, etc., is used, please observe all safety

markings and instructions that accompany the accessory

product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves the

right to change or modify any of the specifications without

notice or obligation to update existing units.

This product, either alone or in combination with an amplifier

and headphones or speaker/s, may be capable of producing

sound levels that could cause permanent hearing loss. DO

NOT operate for long periods of time at a high volume level or

at a level that is uncomfortable. If you experience any hearing

loss or ringing in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

Some Yamaha products may have benches and / or

accessory mounting fixtures that are either supplied with the

product or as optional accessories. Some of these items are

designed to be dealer assembled or installed. Please make

sure that benches are stable and any optional fixtures (where

applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only.

No other uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating

to how a function or effect works (when the unit is operating as

designed) are not covered by the manufacturer's warranty,

and are therefore the owners responsibility. Please study this

manual carefully and consult your dealer before requesting

service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe

and environmentally friendly. We sincerely believe that our

products and the production methods used to produce them,

meet these goals. In keeping with both the letter and the spirit

of the law, we want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery

which (if applicable) is soldered in place. The average life

span of this type of battery is approximately five years. When

replacement becomes necessary, contact a qualified service

representative to perform the replacement.

This product may also use “household” type batteries. Some

of these may be rechargeable. Make sure that the battery

being charged is a rechargeable type and that the charger is

intended for the battery being charged.

When installing batteries, never mix old batteries with new ones,

and never mix different types of batteries. Batteries MUST be

installed correctly. Mismatches or incorrect installation may

result in overheating and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery.

Keep all batteries away from children. Dispose of used

batteries promptly and as regulated by the laws in your area.

Note: Check with any retailer of household type batteries in

your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for

some reason its useful life is considered to be at an end,

please observe all local, state, and federal regulations that

relate to the disposal of products that contain lead, batteries,

plastics, etc. If your dealer is unable to assist you, please

contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The

model number, serial number, power requirements, etc., are

located on this plate. You should record the model number,

serial number, and the date of purchase in the spaces

provided below and retain this manual as a permanent record

of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instruc-

tions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may

void your authority, granted by the FCC, to use the prod-

uct.

2. IMPORTANT: When connecting this product to accesso-

ries and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used.

Follow all installation instructions. Failure to follow instruc-

tions could void your FCC authorization to use this prod-

uct in the USA.

3. NOTE: This product has been tested and found to com-

ply with the requirements listed in FCC Regulations, Part

15 for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance

that your use of this product in a residential environment

will not result in harmful interference with other electronic

devices. This equipment generates/uses radio frequen-

cies and, if not installed and used according to the instruc-

tions found in the users manual, may cause interference

harmful to the operation of other electronic devices. Com-

pliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product

is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try

to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to dis-

tribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Corporation

of America, Electronic Service Division, 6600 Orangetho-

rpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products dis-

tributed by Yamaha Corporation of America or its subsid-

iaries.

* This applies only to products distributed by Yamaha Corporation of America. (class B)

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

Yamaha Corporation of America.

COMPLIANCE INFORMATION STATEMENT

(Supplierʼs declaration of conformity procedure)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Digital Piano

Model Name : YDP-164, YDP-144, YDP-S54

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference

that may cause undesired operation.

(FCC SDoC)

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an

equilateral triangle is intended to alert the

user to the presence of important operating

and maintenance (servicing) instructions in

the literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

9 Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories specified by

the manufacturer.

12 Use only with the cart,

stand, tripod, bracket, or

table specified by the

manufacturer, or sold with

the apparatus. When a cart

is used, use caution when

moving the cart/apparatus

combination to avoid injury

from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has

been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE.

For AC adaptor

YDP-164, YDP-144, YDP-S54 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

• This AC adaptor is designed for use with only Yamaha electronic instruments. Do

not use for any other purpose.

• Indoor use only. Do not use in any wet environments.

CAUTION

• When setting up, make sure that the AC outlet is easily accessible. If some

trouble or malfunction occurs, immediately turn off the power switch of the

instrument and disconnect the AC adaptor from the outlet. When the AC adaptor

is connected to the AC outlet, keep in mind that electricity is flowing at the

minimum level, even if the power switch is turned off. When you are not using

the instrument for a long time, make sure to unplug the power cord from the wall

AC outlet.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the

following:

• Do not place the power cord near heat sources such as heaters or radiators. Also,

do not excessively bend or otherwise damage the cord, or place heavy objects on

it.

• Only use the voltage specified as correct for the instrument. The required voltage

is printed on the name plate of the instrument.

• Use the specified adaptor (page 40) only. Using the wrong adaptor can result in

damage to the instrument or overheating.

• (YDP-164, YDP-S54) Use only the supplied power cord/plug.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the instrument

or attempt to disassemble or modify the internal components in any way. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings. If any liquid such as

water seeps into the instrument, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the instrument inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may fall

over and cause a fire.

• When one of the following problems occur, immediately turn off the power switch

and disconnect the electric plug from the outlet. Then have the device inspected

by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

For AC adaptor

For YDP-164, YDP-144, YDP-S54

Power supply/AC adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

DMI-5 1/2

YDP-164, YDP-144, YDP-S54 Owner’s Manual

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used for

extended periods of time, or during electrical storms.

• Read carefully the attached documentation explaining the assembly process.

Failure to assemble the instrument in the proper sequence might result in

damage to the instrument or even injury.

• (YDP-S54) Be sure to attach the anti-fall brackets to the instrument, to ensure

stability. Failure to do so might result in damage to the instrument or even injury.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• When transporting or moving the instrument, always use two or more people.

Attempting to lift the instrument by yourself may damage your back, result in

other injury, or cause damage to the instrument itself.

• Before moving the instrument, remove all connected cables, to prevent damage

to the cables or injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the power

switch and disconnect the plug from the outlet. Even when the power switch is

turned off, electricity is still flowing to the product at the minimum level. When

you are not using the product for a long time, make sure to unplug the power

cord from the wall AC outlet.

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels and

gradually raise the volume controls while playing the instrument to set the

desired listening level.

• Do not insert a finger or hand in any gaps on the key cover or instrument. Also

take care that the key cover does not pinch your finger.

• Never insert or drop paper, metallic, or other objects into the gaps on the key

cover, panel or keyboard. This could cause physical injury to you or others,

damage to the instrument or other property, or operational failure.

• (YDP-S54) Do not apply excessive force when closing the key cover. A key cover

equipped with the SOFT-CLOSE™ mechanism closes the cover slowly. Applying

excessive force to the key cover when closing it could damage the SOFT-

CLOSE™ mechanism, and possibly result in injury to your hands and fingers

caught under the closing key cover.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

• Do not place the bench in an unstable position where it might accidentally fall

over.

• Do not play carelessly with or stand on the bench. Using it as a tool or stepladder

or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent the

possibility of accident or injury.

• If the bench screws become loose due to extensive long-term use, tighten them

periodically using the specified tool in order to prevent the possibility of accident

or injury.

• Keep special watch over any small children so that they don’t fall off the rear of

the bench. Since the bench does not have a backrest, unsupervised use may

result in accident or injury.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (power lamp is off),

electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure you unplug the

power cord from the wall AC outlet.

Power supply/AC adaptor

Assembly

Location

Connections

Yamaha cannot be held responsible for damage caused by improper use or

modifications to the instrument, or data that is lost or destroyed.

Handling caution

Using the bench (If included)

DMI-5 2/2

The model number, serial number, power requirements, etc., may be found on

or near the name plate, which is at the bottom of the unit. You should note this

serial number in the space provided below and retain this manual as a perma-

nent record of your purchase to aid identification in the event of theft.

Model No.

Serial No.

(bottom_en_01)

The name plate is located on the bottom of the unit.

YDP-164, YDP-144, YDP-S54 Owner’s Manual

NOTICE

To avoid the possibility of malfunction/ damage to the product,

damage to data, or damage to other property, follow the notices

below.

 Handling

• Do not use the instrument in the vicinity of a TV, radio,

stereo equipment, mobile phone, or other electric devices.

Otherwise, the instrument, TV, or radio may generate noise.

When you use the instrument along with an application on

your smart device such as iPad, iPhone or iPod touch, we

recommend that you set “Airplane Mode” to “ON” on that

device in order to avoid noise caused by communication.

• Do not expose the instrument to excessive dust or

vibrations, or extreme cold or heat (such as in direct

sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disfiguration, damage to the internal

components or unstable operation. (Verified operating

temperature range: 5° – 40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the

instrument, since this might discolor the panel or keyboard.

 Maintenance

• When cleaning the instrument, use a soft and dry/slightly

damp cloth. Do not use paint thinners, solvents, alcohol,

cleaning fluids, or chemical-impregnated wiping cloths.

• During extreme changes in temperature or humidity,

condensation may occur and water may collect on the

surface of the instrument. If water is left, the wooden parts

may absorb the water and be damaged. Make sure to wipe

any water off immediately with a soft cloth.

 Saving data

• Some of the data of this instrument (page 31) are retained

when the power is turned off. However, the saved data may

be lost due to some failure, an operation mistake, etc. Save

your important data onto an external device such as a

computer (page 31).

Information

 About copyrights

• Copying of the commercially available musical data

including but not limited to MIDI data and/or audio data is

strictly prohibited except for your personal use.

• This product incorporates and bundles contents in which

Yamaha owns copyrights or with respect to which Yamaha

has license to use others’ copyrights. Due to copyright laws

and other relevant laws, you are NOT allowed to distribute

media in which these contents are saved or recorded and

remain virtually the same or very similar to those in the

product.

* The contents described above include a computer

program, Accompaniment Style data, MIDI data, WAVE

data, voice recording data, a score, score data, etc.

* You are allowed to distribute medium in which your

performance or music production using these contents is

recorded, and the permission of Yamaha Corporation is

not required in such cases.

 About functions/data bundled with the

instrument

• Some of the preset songs have been edited for length or

arrangement, and may not be exactly the same as the

original.

 About this manual

• The illustrations as shown in this manual are for

instructional purposes only, and may appear somewhat

different from those on your instrument.

• The letters at the end of the model name (“B” or “WH,” for

example) are coded information about the finish of the

instrument. For example, “B” indicates “black walnut,” and

“WH” indicates “white.” Since they simply indicate the

finish, these letters are omitted in this manual.

• Windows is a registered trademark of Microsoft®

Corporation in the United States and other countries.

• iPhone, iPad and iPod touch are trademarks of Apple Inc.,

registered in the U.S. and other countries.

• Android™ is a trademark of Google LLC.

• The company names and product names in this manual are

the trademarks or registered trademarks of their respective

companies.

 Tunin g

• Unlike an acoustic piano, this instrument does not need to

be tuned by an expert (although the pitch can be user-

adjusted to match other instruments). This is because the

pitch of digital instruments is always maintained perfectly.

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Table of Contents

PRECAUTIONS .................................... 5

About the Manuals ................................ 9

Included Accessories ............................. 9

Panel Controls and Terminals ............10

Basic Operations

Setting Up.............................................12

Key Cover (YDP-164, YDP-144)............................12

Music Rest (YDP-164, YDP-144)...........................12

Key Cover and Music Rest (YDP-S54)..................13

Turning the Power On.............................................14

Auto Power Off Function........................................15

Using Headphones ...................................................15

Playing the Piano..................................16

Intelligent Acoustic Control (IAC)........................16

Using the Pedals........................................................17

Using the Damper Resonance ................................17

Setting the Operation Confirmation Sounds........18

Changing the Touch Sensitivity .............................18

Using the Metronome..............................................19

Advanced Operations

Playing Various Musical Instrument

Sounds (Voices)....................................20

Selecting a Voice.......................................................20

Listening to the Demo Songs ..................................21

Adding Variations to the Sound (Reverb) ............22

Transposing the Pitch in Semitones ......................23

Fine-tuning the Pitch ...............................................23

Layering Two Voices (Dual mode) ........................24

Playing Duo...............................................................25

Song Playback and Practice .................26

Listening to 50 Preset Songs....................................26

Listening to Songs Loaded from the Computer ...26

Practicing a One-Hand Part....................................27

Playing from the Beginning of a Measure that

Includes Rest or Silence ...........................................27

Recording Your Performance .............28

Recording Your Performance ................................28

Changing the Initial Settings of the Recorded Song

....................................................................................29

Deleting Recorded Data ..........................................29

Using with a Computer or a Smart

Device ................................................... 30

Using an App on Your Smart Device....................30

Playback/Recording of Audio Data (USB Audio

Interface) ................................................................... 30

Backing up Data and Initializing the

Settings................................................. 31

Data Maintained When Power is Turned Off...... 31

Saving User Song data to a computer ...................31

Initializing the Settings............................................ 31

Confirming the firmware version of this

instrument.................................................................31

Appendix

Troubleshooting ..................................32

Keyboard Stand Assembly...................33

Assembly Precautions .............................................33

YDP-164, YDP-144 Assembly................................ 34

YDP-S54 Assembly.................................................. 37

Specifications .......................................40

Index.....................................................42

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Thank you for choosing this Yamaha digital piano.

This instrument provides exceptionally high-quality sound

and expressive control for your playing enjoyment.

In order to make the most of the performance potential and features of the instrument,

please read the manuals thoroughly, and keep them in a handy place for later reference.

About the Manuals

This instrument has the following manuals.

 Included Manuals

Owner’s Manual (this book)

Explains how to use the instrument.

Quick Operation Guide (separate

sheet)

Shows in chart form the functions assigned to the

buttons and the keyboard for quick

understanding.

 Online Manuals (PDF)

Smart Device Connection Manual

Explains how to connect the instrument to a

smartphone or tablet, etc. You can choose from

two versions (for iOS and Android) depending on

your device.

Computer-related Operations

Includes instructions on connecting this

instrument to a computer, and operations related

to transferring song data.

MIDI Reference

Contains the MIDI Data Format and MIDI

Implementation chart, as well as descriptions on

MIDI functions such as MIDI channel and Local

Control settings.

MIDI Basics (only in English, French

and German)

Contains basic explanations about MIDI.

To obtain these materials, access the Yamaha

Downloads website, then enter the model name for

searching the desired files.

Included Accessories

•Owner’s Manual (this book) x1

• Quick Operation Guide (separate sheet) x1

• “50 Classical Music Masterpieces” (music book) x1

• Online Member Product Registration x1

•Warranty* x1

•AC adaptor* x1

• Power cord* x1 (YDP-164, YDP-S54)

• Bench* x1 (YDP-164, YDP-144)

* May not be included depending on your particular

area. Please check with your Yamaha dealer.

Yamaha Downloads

http://download.yamaha.com/

Smart device application – “Smart Pianist”

With the specially developed “Smart Pianist”

app running on your smart device, you can

remotely control your digital piano for even

more convenience and flexibility. By

presenting various parameters on-screen, this

app allows you to make settings in a visual,

more intuitive manner. For more details on

“Smart Pianist,” refer to the following Yamaha

web site.

https://www.yamaha.com/kbdapps/

For instructions on connecting the instrument

to a smart device, Connection Wizard in

“Smart Pianist” will guide you according to the

operating condition and environment. To start

the Connection Wizard, tap “ ” (Menu)

located at the upper left of the screen to open

the Menu display, and then tap “Instrument” →

“Start Connection Wizard.”

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Panel Controls and Terminals

YDP-S54

YDP-164

YDP-144

YDP-164, YDP-144

The illustrations are taken from the YDP-144.

Bottom

(Keyboard side)

Bottom

(Keyboard side)

Bottom

(Keyboard side)

Music braces (YDP-164)

Music rest

PHONES

Bottom

Rear

Bottom

(Keyboard side)

YDP-164, YDP-144, YDP-S54 Owner’s Manual

[] (Standby/On) switch......................... page 14

For turning the power on or setting to standby.

[MASTER VOLUME] knob

For adjusting the volume of the entire sound.

CAUTION

Do not use this instrument at a high volume level for a

long period of time, to avoid damaging your hearing.

[DEMO/SONG] button..................... pages 21, 26

For playing the Demo Songs and the Preset Songs.

[PIANO/VOICE] button............. pages 20, 22, 24

For selecting a single Voice, two Voices for layering or

a Reverb Type.

[METRONOME] button .......................... page 19

For starting or stopping the metronome.

[+R], [–L] buttons ................. pages 19, 20, 26, 27

• In general, these are for selecting the next or

previous Voice.

• During Song playback, these are for selecting the

next or previous Song, and (while holding down

[PLAY]) turning on/off the right-hand and left-

hand Parts individually.

• During Metronome playback, these are for

increasing or decreasing the Tempo.

[REC] button............................................ page 28

For recording your keyboard performance.

[PLAY] button.......................................... page 28

For playing back the recorded performance.

[FUNCTION] ................................... pages 15, 23

Simultaneously holding both [DEMO/SONG] and

[PIANO/VOICE] and pressing a specified key allows

you to change various settings, including Auto Power

off function, Transpose parameters, etc.

[PHONES] jacks....................................... page 15

For connecting a set of standard stereo headphones.

Headphone hanger (YDP-164 only)

You can hang the headphones on this instrument

when not using them.

For instructions on installing the headphone hanger,

refer to “Keyboard Stand Assembly” on page 36.

NOTICE

Do not hang anything other than the headphones on the

hanger.

Doing so may damage this instrument or the hanger.

[USB TO HOST] terminal ....................... page 30

For connecting to a computer or a smart device such

as an iPhone or iPad.

DC IN jack................................................ page 14

For connecting the AC adaptor.

[TO PEDAL] jack .............................. pages 36, 39

For connecting the pedal cord.

Pedals ....................................................... page 17

For controlling expression and sustain, just as on an

acoustic piano.

Level decreases Level increases

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Basic Operations

Setting Up

To open the key cover:

Lift the cover slightly, then push and slide it to the

end.

To close the key cover:

Slide the cover toward you and gently lower the

cover over the keys.

CAUTION

• Hold the cover with both hands when opening or closing it.

Do not release it until it is fully opened or closed. Be

careful to avoid catching fingers (yours or others,

especially children’s) between the cover and main unit.

• Do not place objects, such as a piece of metal or paper, on

top of the key cover. Small objects placed on the key cover

may fall inside the unit when the cover is opened and may

be nearly impossible to remove. This could cause electric

shock, short circuit, fire or other serious damage to the

instrument.

To raise the music rest:

1. Pull the music rest up and toward

yourself as far as it will go.

Flip down the two metal supports at the

left and right on the rear of the music rest.

3. Lower the music rest so that the metal

supports latch into place.

(YDP-164) Music braces allow you to hold the

pages of music books in place.

CAUTION

Do not try to use the music rest in a half-raised position.

When lowering the music rest, do not release your hands

from the music rest until it is all the way down.

To lower the music rest:

(YDP-164) Close the Music braces if they are open,

and then lower the music rest by following the

instructions below.

1. Pull the music rest toward yourself as far

as it will go.

2. Raise the two metal supports (at the rear

of the music rest).

3. Gently lower the music rest backward

until it is all the way down.

Key Cover (YDP-164, YDP-144)

CAUTION

Be careful to avoid catching

your fingers when opening or

closing the cover.

Music Rest (YDP-164, YDP-144)

Music braces (YDP-164)

Setting Up

YDP-164, YDP-144, YDP-S54 Owner’s Manual

CAUTION

Hold the key cover with both hands when opening or closing

it. Do not release it until it is fully opened or closed. Be careful

to avoid catching fingers (yours or others, especially

children’s) between the key cover and main unit.

Opening the key cover

1. Hold the edge of the key cover top with

both hands, then open the key cover

slowly.

2. Fold down the front part of the key

cover.

3. Unfold the music rest.

Closing the key cover

1. Fold the music rest.

2. Unfold the front part of the key cover.

3. Hold the key cover with both hands and

close it slowly.

The key cover is equipped with the special SOFT-

CLOSE™ mechanism which closes the cover slowly.

CAUTION

Do not apply excessive force when closing the key cover.

Applying excessive force to the key cover when closing it

could damage the SOFT-CLOSE™ mechanism, and possibly

result in injury to your hands and fingers caught under the

closing key cover.

Key Cover and Music Rest

(YDP-S54)

CAUTION

Be careful to avoid catching your fingers when opening

or closing the cover.

CAUTION

Be careful to avoid catching your fingers when opening

or closing the cover.

NOTICE

Before closing the key cover, be sure to fold the music

rest and unfold the front part of the key cover.

Setting Up

YDP-164, YDP-144, YDP-S54 Owner’s Manual

1. Connect the plugs of the AC adaptor in

the order shown in the illustration.

YDP-164, YDP-S54

YDP-144

WARNING

Use the specified adaptor (page 40) only. The use of other

adaptors may result in irreparable damage to both the adaptor

and the instrument.

CAUTION

Remove the AC plug from the AC outlet when the instrument

is not to be used for extended periods of time, or during

electrical storms.

NOTE

Follow this procedure in reverse order when disconnecting the

AC adaptor.

For the Power Adaptor with a Removable Plug

Do not remove the plug from the power adaptor. If

the plug is removed accidentally, slide the plug into

place without touching the metallic parts, and then

push the plug in completely until it clicks.

WARNING

• Make sure to keep the plug attached to the AC adaptor.

Using the plug alone can cause electric shock or fire.

• Never touch the metallic section when attaching the plug.

To avoid electric shock, short circuit or damage, also be

careful that there is no dust between the AC adaptor and

plug.

2. Press the [](Standby/On) switch to

turn the power on.

Power indicator

If you close the key cover without turning the

power to standby, the power indicator remains lit,

indicating that the power is still on.

When you’re ready to turn the power to standby,

press the [ ] (Standby/On) switch again for a

second. The power indicator turns off.

CAUTION

Even when the [ ] (Standby/On) switch is in the standby

status, electricity is still flowing to the instrument at a

minimum level. When not using the instrument for an

extended period of time, be sure to unplug the power cord

from the wall AC outlet.

NOTICE

Press only the [] (Standby/On) switch when turning the

power on. Any other operations, such as pressing the keys,

buttons or pedals may cause the instrument to malfunction.

Turning the Power On

AC outlet

AC adaptor

DC IN jack (page 11)

DC plug

Power cord

AC plug

The shape of the plug and outlet differ depending on the

locale.

AC outlet

AC adaptor

DC IN jack (page 11)

DC plug

Plug

Slide the plug

as indicated

The shape of the plug and outlet differ depending on the locale.

Power indicator

[ ] (Standby/On) switch

Setting Up

YDP-164, YDP-144, YDP-S54 Owner’s Manual

To prevent unnecessary power consumption, this

instrument features an Auto Power Off function

that automatically turns the power off if the

instrument is not operated for approximately

30 minutes.

Default setting: Enabled

Disabling Auto Power Off (simple method)

Turn off the power of the instrument once.

While holding down the A-1 key (the lowest key),

press the [ ] (Standby/On) switch to turn the

instrument on. The [REC] indicator flashes three

times, indicating the Auto Power Off function has

been disabled.

Switching the Auto Power Off Function

(Enable/Disable)

While holding down [DEMO/SONG] and

[PIANO/VOICE] simultaneously, press the A#0

key to enable the Auto Power Off function or the

A0 key to disable it.

Since this instrument is

equipped with two

[PHONES] jacks, you

can connect two sets of

standard stereo

headphones. If you are

using only one set of

headphones, insert a plug

into either jack, which

automatically shuts off

the speakers according to

the default setting.

CAUTION

Do not use headphones at a high volume for an extended

period of time; doing so may cause hearing loss.

Speaker On/Off setting

You can set whether the sound of this instrument is

always output from its built-in speaker or not.

While holding down [DEMO/SONG] and

[PIANO/VOICE] simultaneously, press one of the

D6 – E6 key.

Reproducing a natural sense of distance

(Stereophonic Optimizer)

The Stereophonic Optimizer gives you the feeling

of playing an actual acoustic piano — even though

you’re listening through headphones. Normally, the

sound comes out from headphones sounds very

close to your ears. However, this Stereophonic

Optimizer effect recreates a natural distance or the

sense of physical space between your ears and the

instrument, just as when playing an acoustic piano.

Default setting: On

While holding down [PIANO/VOICE], press the

F#3 key to turn the function on or the F3 key to

turn the function off.

Auto Power Off Function

Using Headphones

Lowest key

A#0 (Enable)

Lowest key

A0 (Disable)

PHONES

Bottom surface

Standard stereo phone plug

Off

(D6 key)

The speaker will not sound.

(D#6 key)

The speaker will always sound regardless

of whether a set of headphones is

connected or not.

Normal

(E6 key)

The speaker will sound only if headphones

are not connected. (This is the default

setting.)

D#6 (On)

Highest key

D6 (Off)

E6 (Normal)

F3 (Off)

F#3 (On)

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Playing the Piano

With this function, the sound quality of this instrument is automatically adjusted

and controlled according to the overall volume. Even when the volume is low,

this lets you hear both low sounds and high sounds clearly.

To tu rn on IAC:

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,

press the C#2 key.

To turn off IAC:

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,

press the C2 key.

To adjust IAC Depth:

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,

press the D2 key to decrease the value, or the E2 key to increase.

The higher the value, the more clearly that low and high sounds are heard at

lower volume levels.

Intelligent Acoustic Control (IAC)

Default setting:

C#2Lowest key

Lowest key

D2 (Depth -1)

E2 (Depth +1)

D#2 (Default)

Setting range:

-3 – +3

Default setting:

0 (D#2)

Playing the Piano

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Damper Pedal (Right)

Pressing this pedal will sustain notes longer.

Releasing this pedal immediately stops (damps)

any sustained notes. This pedal also features a

“half-pedal” function that creates partial sustain

effects, depending on how far down you press the

pedal.

Sostenuto Pedal (Center)

Pressing this pedal while holding the notes will

sustain the pressed notes (as if the Damper Pedal

had been pressed), but all subsequently played

notes will not be sustained. This makes it possible

to sustain a chord or single low note, for example,

while the other notes are played “staccato.”

Soft Pedal (Left)

Pressing this pedal will reduce the volume and slightly change the timbre of the

notes. The notes played before this pedal is pressed are not affected.

The Damper Resonance effect simulates the sustain sound of the damper pedal on a grand piano, as if you

were pressing the damper pedal and playing the keyboard. This effect is applied only to the Piano Voices

(page 20).

To turn on the Damper Resonance:

While holding [PIANO/VOICE], press the C#3 key.

To turn off the Damper Resonance:

While holding [PIANO/VOICE], press the C3 key.

Using the Pedals

When you press the damper

pedal here, this note and the

notes you play before you release

the pedal sustain longer.

When you press the sostenuto

pedal here while holding the

note, the note will sustain as

long as you hold the pedal.

NOTE

If the damper pedal doesn’t

work, make sure that the pedal

cord is properly plugged into

the main unit (page 39).

Half-pedal function

This function allows you to vary

the sustain length depending

on how far the pedal is

pressed. The farther down you

press the pedal, the more the

sound sustains. For example, if

you press the damper pedal

and all notes you are playing

sound a bit murky and loud

with too much sustain, you can

release the pedal half way or

higher to decrease the sustain

(murkiness).

NOTE

While the sostenuto pedal is

held, the organ and strings

Voices sound continuously

without decay after the notes

have been released.

NOTE

When Jazz Organ Voice

(page 20) is selected,

pressing the left pedal

switches between fast/slow

rotation of the rotary speaker.

When the Vibraphone Voice

(page 20) is selected, the left

pedal switches Vibrato on and

off.

Using the Damper Resonance

Default setting:

Lowest key C3 (Off)

C#3 (On)

Playing the Piano

YDP-164, YDP-144, YDP-S54 Owner’s Manual

When a setup is changed using a button and key combination, an operation sound (on, off, click, tempo

value input) is sounded. This confirmation sound can be enabled (on) or disabled (off) as desired.

Turning the Operation Confirmation Sounds on

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,

press the A#-1 key.

Turning the Operation Confirmation Sounds off

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,

press the A-1 key.

You can specify the Touch Sensitivity (how the sound responds to the way you

play the keys).

While holding down [PIANO/VOICE], press one of the C6 – D#6 keys.

Setting the Operation Confirmation Sounds

Default setting:

Lowest key A-1 (Off)

A#-1 (On)

Changing the Touch Sensitivity

NOTE

This setting is disabled with

some Voices, such as an

organ sound.

Default setting:

C#6 (Medium)

Key

Touch

Sensitivity

Description

C6 Soft

The volume level does not change much when you play the

keyboard soft or hard.

C#6 Medium This is the standard piano touch response.

D6 Hard

The volume level changes very widely from pianissimo to fortissimo

to facilitate dynamic and dramatic expression. You have to hit the

keys hard to produce a loud sound.

D#6Fixed

The volume level does not change at all regardless of whether you

play the keyboard soft or hard.

C6 Highest key (C7)D6

C#6D#6

Playing the Piano

YDP-164, YDP-144, YDP-S54 Owner’s Manual

The metronome feature is convenient for practicing with an accurate tempo.

1. Press [METRONOME] to start the Metronome.

2. Press [METRONOME] to stop the Metronome.

Metronome setting

While holding down the [METRONOME] button, press one of the highlighted

keys shown below to set the Metronome parameter.

Voice confirmation of current Tempo value (in English)

While holding down [METRONOME], press the A-1 key (lowest key).

Selecting the Beat (time signature)

While holding down [METRONOME], press one of the C3 – F3 keys.

The first beat is accented with a bell sound and the rest with clicks. Default set is

0 (C3). In this setting, clicks sound in all beats.

Adjusting the Tempo

The Metronome tempo can be set from 5 to 280 beats per minute.

•To increase or decrease the value by 1:

While holding down [METRONOME], press [+R] to increase or [–L] to decrease.

While the metronome is playing, press [+R] to increase or [–L] to decrease.

•To increase or decrease the value by 10:

While holding down [METRONOME], press the D2 key to increase or the C2 key

to decrease.

•To specify a numeric value:

While holding down [METRONOME], press the relevant C1 – A1 keys one by one

in order. Specifying three digits or releasing [METRONOME] after specifying one

or two digits will enter the value.

•Resetting the value to the default (120)

While holding down [METRONOME], press [+R] and [–L] simultaneously, or

press the C#2 key. While the metronome is playing, press [+R] and [–L]

simultaneously.

Adjusting the Volume

While holding down [METRONOME], press the G0 key to increase the volume

or the F0 key to decrease. To reset to the default setting, press the F#0 key while

holding down [METRONOME].

Using the Metronome

22447

13 3056 56

C#3D#3

D3 E3 F3F0 A1G0Lowest key A-1 C1 C2 D2 C3

C#2 (Default setting)F#0 (Default setting)

Adjusting

the Volume

Selecting the Beat

(time signature)

Adjusting

the Tempo

Confirming the

current Tempo

Key

Beat (time

signature)

C3 0 (no accent)

C#32

D3 3

D#34

E3 5

F3 6

Setting range:

1 – 10

Default setting:

7 (F#0)

NOTE

A numeric value is read out

when a relevant key is

pressed.

If the entered value is outside

the setting range, it will be

ignored.

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Advanced Operations

Playing Various Musical Instrument Sounds (Voices)

To select “CFX Grand”:

Simply press [PIANO/VOICE].

To select another Voice:

After pressing [PIANO/VOICE], press [+R] or [–L] to select the next or previous

Voi ce.

To select a specific Voice:

While holding down [PIANO/VOICE], press one of the C1 – A1 keys. For details

on which Voice is assigned to each key, see the list below.

Voice List

Selecting a Voice

NOTE

To hear the characteristics of

the Voices, play back the

Demo Songs (page 21).

Key Voice Na me Voice description

C1 CFX Grand

Yamaha’s CFX flagship concert grand piano sound with a wide

dynamic range for maximum expressive control. Suitable for

playing in any music genre and style.

C#1 Mellow Grand

Grand piano sound with a soft and warm tone. Good for playing

ballads.

D1 Pop Grand

Bright piano sound. Good for clear expression and “cutting

through” other instruments in an ensemble.

D#1 Stage E.Piano

The sound of an electric piano using hammer-struck metallic

“tines.” Soft tone when played lightly, and an aggressive tone

when played hard.

E1 DX E.Piano

An electronic piano sound created by FM synthesis. Good for

standard popular music.

F1 Harpsichord

The definitive instrument for baroque music. Since harpsichord

uses plucked strings, there is no touch response. There is,

however, a characteristic additional sound when the keys are

released.

F#1 Vibraphone

Vibraphone played with relatively soft mallets. The tone becomes

more metallic the harder you play.

G1 Pipe Organ

This is a typical pipe organ sound (8 feet + 4 feet + 2 feet). Good

for sacred music from the Baroque period.

G#1 Jazz Organ

The sound of a “tonewheel” type electric organ. Often heard in

jazz and rock music.

A1 Strings

Stereo-sampled, large-scale strings ensemble with realistic

reverb. Try combining this Voice with piano in the Dual mode.

C#1D#1F#1G#1

C1 D1 E1 F1 G1 A1Lowest key

Playing Various Musical Instrument Sounds (Voices)

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Special individual Demo Songs are provided for all of the instrument Voices.

1. Press [DEMO/SONG] to start playback.

The Demo Song for the current Voice starts. During playback, the [PLAY] lamp

flashes at the current tempo.

Starting with the selected song, the playback of the Demo Songs will continue.

After the last demo song, the sequence then returns to the first Demo Song and

repeats until you stop it.

To change the Demo Song during playback:

Press [+R] or [–L] to change to the next or previous Demo Song.

To change to a specific Demo Song, press and hold down [DEMO/SONG], then

press one of the C1 – A1 keys.

2. Press [DEMO/SONG] or [PLAY] to stop playback.

The [PLAY] lamp turns off.

Demo Song List

The Demo Songs excluding original Songs are short rearranged excerpts from the original

compositions. The original Demo Songs are Yamaha originals (© Yamaha Corporation).

Listening to the Demo Songs

NOTE

If you want to change the

playback tempo, see page 19.

Key Voice Na me Title Composer

C1 CFX Grand

El pelele - Escena goyesca,

Goyescas - Los majos enamorados II No.7

E. Granados

C#1 Mellow Grand

Von fremden Ländern und Menschen,

Kinderszenen op. 15-1

R. Schumann

D1 Pop Grand Original —

D#1 Stage E.Piano Original —

E1 DX E.Piano Original —

F1 Harpsichord

Concerto a cembalo obbligato, 2 violini, viola e

continuo No.7, BWV 1058

J. S. Bach

F#1 Vibraphone Original —

G1 Pipe Organ Herr Christ, der ein'ge Gottes-Sohn, BWV 601 J. S. Bach

G#1 Jazz Organ Original —

A1 Strings Original —

Lowest key C1 A1

Playing Various Musical Instrument Sounds (Voices)

YDP-164, YDP-144, YDP-S54 Owner’s Manual

This instrument features several Reverb Types that add extra depth and expression to the sound to create a

realistic acoustic ambience. The appropriate Reverb Type and Depth are called up automatically when you

select each of the Voices and Songs. This is why the Reverb Type need not be selected; however, you can

change it if desired.

To select a Reverb Type:

While holding down [PIANO/VOICE], press one of the C2 – E2 keys.

Reverb Type List

To adjust Reverb Depth:

While holding down [PIANO/VOICE], press the G2 key to decrease the value by

1 or the A2 key to increase the value by 1.

While holding down [PIANO/VOICE], press the G#2 key to reset the Reverb

Depth to the default setting, which is the most suitable value for the current

Voi ce.

Adding Variations to the Sound (Reverb)

Key Reverb Type Description

C2 Recital Hall

Simulates the clear reverb sound you would hear in a medium-

sized concert hall for piano recitals.

C#2 Concert Hall

Simulates the gorgeous reverb sound you would hear in a large

concert hall for orchestral performances.

D2 Chamber

Suitable for playing chamber music; simulates the intimate

reverb sound you would hear in a spacious room, such as for

classical music recitals.

D#2Club

Simulates the vivid reverb sound you would hear in a live music

venue or a jazz club.

E2 Off No effect is applied.

Lowest key

A2 (Depth +1)

G#2 (Default)

G2 (Depth -1)

C#2D#2

C2 D2 E2

Selecting a

Reverb Type

Adjusting

Reverb Depth

Setting range:

0 (no effect) – 20 (maximum

depth)

Reverb in Dual Mode

(page 24)

An optimum reverb type for the

combination of Voices is

assigned automatically.

Playing Various Musical Instrument Sounds (Voices)

YDP-164, YDP-144, YDP-S54 Owner’s Manual

You can shift the pitch of the entire keyboard up or down in semitones in order to facilitate playing in

difficult key signatures, or to easily match the pitch of the keyboard to the range of a singer or other

instruments. For example, if “+5” is selected, playing key C produces pitch F, letting you play a song of F

major as though it were in C major.

To transpose the pitch down:

While holding down [DEMO/SONG] and [PIANO/VOICE], press a key

between F#2 (-6) and B2 (-1).

To transpose the pitch up:

While holding down [DEMO/SONG] and [PIANO/VOICE], press a key

between C#3 (+1) and F#3 (+6).

To restore the normal pitch:

While holding down [DEMO/SONG] and [PIANO/VOICE], press the C3 key.

You can fine-tune the pitch of the entire instrument in about 0.2 Hz steps. This lets you accurately match the

keyboard pitch to that of other instruments or CD music.

To tune up (in about 0.2 Hz steps):

Press and hold down [DEMO/SONG] and

[PIANO/VOICE] simultaneously, and press [+R].

To tune down (in about 0.2 Hz steps):

Press and hold down [DEMO/SONG] and

[PIANO/VOICE] simultaneously, and press [–L].

To set the pitch to 442.0 Hz:

Press and hold down [DEMO/SONG]

and [PIANO/VOICE] simultaneously,

and press the C#1 key.

To restore default pitch (440.0 Hz):

While simultaneously holding down [DEMO/

SONG] and [PIANO/VOICE], press [+R] and

[–L] simultaneously. Alternately, you can press

the C1 key while holding down [DEMO/

SONG] and [PIANO/VOICE] simultaneously.

Transposing the Pitch in Semitones

NOTE

The transposition setting

affects not only the pitch of the

keyboard but also the pitch of

Song playback (page 26).

The transposition setting of the

Transposition for the Keyboard

and the Song cannot be set

independently.

-5 -3 -1 0 +2 +4 +5

-6 -4 -2 +1

+3 +6

F#2

Lowest key

F#3

Transpose down Transpose up

C3 (Normal pitch)

Fine-tuning the Pitch

Hz (Hertz)

This unit of measurement

refers to the frequency of a

sound and represents the

number of times a sound wave

vibrates in a second.

Setting range:

414.8 – 466.8 Hz

Default setting:

A3 = 440.0 Hz

C#1

Lowest key

Playing Various Musical Instrument Sounds (Voices)

YDP-164, YDP-144, YDP-S54 Owner’s Manual

You can layer two Voices and play them simultaneously to create a more richly textured sound.

1. Engage the Dual mode.

While holding down [PIANO/VOICE], simultaneously hold down two keys

between C1 and A1 to select the two desired Voices. For information on which

Voices are assigned to the keys, refer to “Voice List” (page 20).

The Voice assigned to the lower key will be designated as Voice 1, and the Voice

assigned to the higher key will be designated as Voice 2. You cannot assign the same

Voice to both Voice 1 and Voice 2 simultaneously in Dual mode.

To shift the Octave for each Voice:

While holding down [PIANO/VOICE], press one of the keys F5 – G5 or A5 – B5 as

shown in the illustration below. For example, pressing the B5 key twice while

holding down [PIANO/VOICE] shifts Voice 1 up by two octaves. To restore the

default setting, simultaneously hold down [PIANO/VOICE] and press the A#5 key

for Voice 1 or the F#5 key for Voice 2.

To adjust the Balance between two Voices:

While holding down [PIANO/VOICE], press the C5 key to decrease the value or

the D5 key to increase. When the value is set to “0,” the volume levels of the two

Voices reset to their respective default settings. Settings below “0” increase the

volume of Voice 2, while settings above “0” increase the volume of Voice 1, in

relation to the other.

2. To exit from Dual mode, press [PIANO/VOICE].

Layering Two Voices (Dual mode)

C1 A1

Lowest key

Engaging Dual mode

NOTE

The Dual and Duo modes

(page 25) cannot be engaged

at the same time.

Setting range:

-2 – 0 – +2

Setting range:

-6 – 0 – +6

-1

+1-1

+1 -1

Highest key

C#5F5 B5

Shifting the octave

Adjusting the balance

Voice 2

Voice 1

Playing Various Musical Instrument Sounds (Voices)

YDP-164, YDP-144, YDP-S54 Owner’s Manual

This function allows two different players to play the instrument, one on the left and the other on the right,

over the same octave range.

1. While holding down [PIANO/VOICE], press [+R] and [–L]

simultaneously to engage Duo.

The keyboard is divided into two sections, with the E3 key as the Split Point.

2. One person can play the left section of the keyboard while

the other plays the right.

To shift the O ctave for each sec ti on:

Same operation as in Dual (page 24).

In Duo, the left section is assigned to Voice 2, while the right section is assigned to

Voice 1.

To adjust the volume balance between two keyboard sections:

Same operation as in Dual (page 24).

Settings below “0” increase the volume of Left Voice (Voice 2), while settings above

“0” increase the volume of Right Voice, in relation to the other.

Pedal function in Duo

Damper Pedal: Applies Sustain to the right section.

Sostenuto Pedal: Applies Sustain to both sections.

Soft Pedal: Applies Sustain to the left section.

3. To exit from Duo, simultaneously hold down [PIANO/

VOICE] and press [+R] and [–L].

Playing Duo

NOTE

• Different Voices cannot be

assigned to the Right Voice

and Left Voice.

• The Split Point cannot be

changed from E3.

• In Duo, Reverb, Damper

Resonance and

Stereophonic Optimizer are

not effective.

Split Point E3Equivalent to C3 (middle C) Equivalent to C3 (middle C)

Left section (Voice 2) Right section (Voice 1)

Setting range:

-2 – 0 – +2

Setting range:

-6 – 0 – +6

NOTE

Sounds played in the left

section are played from the left

speaker, and sounds played in

the right section are played

from the right speaker.

Moreover, when using

headphones, sounds played in

the left section are played by

the left channel, and sounds

played in the right section are

played by the right channel of

the headphones.

NOTE

If the keyboard is in Dual

mode, engaging Duo will exit

from Dual, and Voice 1 is used

over the entire range of the

keyboard.

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Song Playback and Practice

In addition to the Demo Songs, Preset Songs are provided for your listening pleasure.

1. Find the number of the Song that you want to play back

from the included “50 Classical Music Masterpieces.”

2. While holding down [DEMO/SONG], press one of the C2 –

C#6 keys to start playback.

The number of each piano Preset Song is assigned to the C2 – C#6 keys.

During playback, the [+R] and [–L] lamps light, and the [PLAY] lamp flashes at the

current tempo. Playback of the Preset Songs continues in sequence, starting with

the selected song. After the last Preset Song, the sequence then returns to the first

Preset Song and repeats until you stop it.

To change the Preset Song during playback:

Press [+R] or [–L] to change to the next or previous Preset Song, or directly select the

desired Song by holding down [DEMO/SONG] and pressing the appropriate key.

To change the tempo during playback:

While holding down [METRONOME], press [+R] or [–L] to increase or decrease

the Tempo value by 1. Other instructions are the same as those of the Metronome

Tempo (page 19).

To play back from the beginning of the Song

During playback, press [+R] and [–L] simultaneously to jump to the playback

position at the beginning of the Song then continue playback at the last specified

tempo.

3. Press [DEMO/SONG] or [PLAY] to stop playback.

The [PLAY], [+R] and [–L] lamps turn off.

You can transfer up to 10 songs from your computer to this instrument and play

them back. For details on transferring Songs from a computer and playing them

back on this instrument, refer to the “Computer-related Operations” section on

the website (page 9).

Types of file that can be exchanged with a computer

Files with a .mid extension (SMF format 0 or 1)

Listening to 50 Preset Songs

Highest key (C7)

Song 1 Song 10 Song 20 Song 30 Song 40

C3 C4 C5

Song 50 (C#6)

NOTE

You can play the keyboard

along with the Preset Song.

You can also change the Voice

played from the keyboard.

Song:

In this manual, performance

data is called a “Song.” This

includes 50 Preset Songs and

Demo Songs.

NOTE

The Preset Songs, Demo

Songs and other Songs (a

maximum of ten) transferred

from a computer can be

played back consecutively

within each category.

NOTE

You can import additional

Songs by loading SMF files

from a computer. For details,

refer to the “Computer-related

Operations” on the website

(page 9).

Listening to Songs Loaded from the Computer

NOTE

Certain MIDI files in SMF format

0 or 1 may contain data that is

not supported by your digital

piano, and such files may not

play as originally intended. If

this is the case, setting the song

playback channels to “1&2”

may enable a better rendition of

the song. For details, refer to

the “Computer-related

Operations” section on the

website (page 9).

Song Playback and Practice

YDP-164, YDP-144, YDP-S54 Owner’s Manual

All the Songs except for the Demo (page 21) let you turn on or off the left-hand and right-hand Parts

individually. By turning off [+R], for example, you can practice the right-hand Part while the left-hand Part

is playing back, and vice versa.

1. Start playback of a Preset Song (page 26) or the User Song

(page 28).

2. While holding down [PLAY], press [+R] or [–L] to turn the

Part on/off.

Pressing the same button repeatedly while holding down [PLAY] toggles playback on

and off. The lamp of the button lights to indicate that the corresponding Part is on.

3. Practice the Part which is turned off.

To change the Tempo :

If desired, you can change the tempo for your practice convenience. For details,

refer to page 19.

4. Press [PLAY] to stop playback.

This Quick Play feature enables you to specify whether a Song should play back

immediately from the very first note, or play back any silence or rests that exist

before the first note.

To tu rn on Quick Play :

Hold down [DEMO/SONG] and press the A#-1 key to enable immediate

playback from the first note or first pedal operation.

To turn off Quick Play:

Hold down [DEMO/SONG] and press the lowest key (A-1) to play from the top

of the first measure (including a rest or blank).

Practicing a One-Hand Part

NOTE

Selecting another Song will

reset the on/off status.

NOTE

Songs 16 – 20 of “50 Classical

Music Masterpieces” are duet

songs. The right-hand Part is

for the first player, and the left-

hand Part is for the second

player.

or Lamp lights when Part is on.

Playing from the Beginning of a Measure that Includes Rest or Silence

Default setting:

A#-1

Lowest key

Lowest key (A-1)

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Recording Your Performance

This instrument lets you record your keyboard performance as the User Song. Up to two Parts (left-hand and

right-hand) can be recorded separately. The recorded Song data can be saved to a computer as a Standard

MIDI file (SMF; page 31).

1. Select the desired Voice and other parameters, such as beat

(time signature), for recording.

For instructions on selecting a Voice, refer to page 20. If necessary, set other

parameters, such as beat (time signature) and effects, in this step.

2. Engage the Record Ready mode.

Quick Recording

Press [REC] to engage the Record Ready mode. Your keyboard performance will be

automatically recorded to the right-hand part. Note that the already-recorded data

of the right- and left-hand parts will be erased by Quick Recording.

Recording to individual parts

While holding down [REC], press [+R] or [–L] to engage the Record Ready mode

for the Part you want to record.

If data has already been recorded to the other Part, the data in this Part will be

played back while recording.

To turn the Part off or on, press the appropriate part button ([+R] or [-L]) while

holding down [PLAY].

To exit from Record Ready mode:

Simply press [REC].

3. Play the keyboard or press [PLAY] to start recording.

The [REC] lamp lights up while the Recording Part lamp flashes at the current

tempo.

4. Press either [REC] or [PLAY] to stop recording.

The [REC], [PLAY], [+R] and [–L] lamps flash, indicating that the recorded data is

being stored. After the Save operation is completed, the lamps will turn off,

indicating that the Record operation has been completed.

5. To hear the recorded Song, press [PLAY] to start playback.

Press [PLAY] again to stop playback.

To record to the other part

Repeat the steps above. In step 2, follow the instructions of “Recording individual

parts.”

Recording Your Performance

NOTE

The Recording function of this

instrument will record your

keyboard performance as

MIDI data. If you want to

record audio data, you can

connect a computer to the

instrument for that purpose.

Refer to page 30 for details.

NOTE

You can use the Metronome

while recording; however, the

Metronome sound will not be

recorded.

NOTE

If the keyboard is in the Duo

mode (page 25), the data will

be recorded to each Part. The

Part for recording cannot be

specified.

NOTICE

Note that recording your

performance to a part

containing data will replace

already-recorded data with

the new data.

NOTE

If the data capacity of the

instrument approaches full

when you engage Record

Ready mode, the [REC] and

[PLAY] lamps flash quickly for

about three seconds.

To record the right-hand Part ([+R]) To record the left-hand Part ([–L])

NOTICE

Never turn off the power

while the recorded data is

being stored (while the

lamps are flashing).

Otherwise, all recorded data

will be lost.

Recording Capacity

This instrument can record up

to 100 KB (approximately

11,000 notes).

Recording Your Performance

YDP-164, YDP-144, YDP-S54 Owner’s Manual

The settings of the following parameters can be changed after the Record operation is completed.

• For individual Par ts: Voice, Volume balance (Dual/Duo), Reverb Depth, Damper Resonance

• For the entire Song: Tempo, Reverb Type

1. Make settings for the above parameters as desired.

2. While holding down [REC], press the desired Part button to

engage Record Ready mode.

The [REC], [PLAY] and selected Part ([+R] or [–L]) lamps flash.

In this status, do not press [PLAY] again or any key. Otherwise, the originally

recorded performance data will be deleted.

3. While holding down [REC], press [PLAY] to exit from

Record Ready mode.

The [REC], [PLAY], [+R] and [–L] lamps flash. After the Save operation is

completed, the lamps will turn off, indicating that the operation has been

completed.

Confirm the setting by playing the Song.

To delete the entire Song:

1. While holding down [REC], press [DEMO/SONG].

The [REC] and [PLAY] lamps flash alternately.

To exit from this status, press [REC].

2. Press [PLAY] to delete the data of the entire Song.

The [REC], [PLAY], [+R] and [–L] lamps flash.

After the operation is completed, all lamps turn off.

To delete a specific Part:

1. While holding down [REC], press [+R] or [–L] (depending

on the Part you want to delete) to engage Record Ready

mode.

The [REC], [PLAY] and selected Part ([+R] or [–L]) lamps flash.

2. Press [PLAY] to start recording without playing the

keyboard.

The selected Part ([+R] or [–L]) lamp flashes.

3. Press [REC] or [PLAY] to stop recording.

All data recorded for the selected Part will be deleted, and the lamp turns off.

Changing the Initial Settings of the Recorded Song

Deleting Recorded Data

NOTE

If a User Song has not been

recorded to the instrument, the

[REC] and [PLAY] lamps flash

quickly for about three

seconds.

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Using with a Computer or a Smart Device

Connecting this instrument to a computer or a smart device such as iPhone/iPad allows you to transmit/

receive performance data and Song data to/from the computer or a smart device. For details on connections,

refer to the “Computer-related Operations” section or the “Smart Device Connection Manual” section on the

website (page 9).

By using an app on a smart device, you can take advantage of convenient

functions and get more enjoyment out of this instrument. In particular, with the

“Smart Pianist” app running on your smart device, you can remotely control

your digital piano for even more convenience and flexibility.

For information about the compatible smart devices and apps, access the

following page:

https://www.yamaha.com/kbdapps/

You can play back audio data on a smart device or a computer with this

instrument. You can also record your keyboard performance as audio data to a

music production app on a smart device or a computer.

When using this function on a computer running Windows, you will need to

install the Yamaha Steinberg USB Driver to your computer. For details, refer to

the “Computer-related Operations” on the website (page 9).

Audio Loop Back On/Off

You can set whether audio sound input from the [USB TO HOST] terminal is

returned to the computer/smart device or not along with the performance played

on the instrument.

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,

press the G5 key to turn this parameter “Off” or the G#5 key to turn it “On.”

NOTICE

Use an AB type USB cable of

less than 3 meters. USB 3.0

cables cannot be used.

NOTE

For instructions on using MIDI,

refer to the online manual

“MIDI Reference” (page 9).

Computer

USB terminal

[USB TO HOST]

terminal (page 10)

USB cable

Instrument Smart device

Using an App on Your Smart Device

NOTICE

Do not place your smart

device in an unstable

position. Doing so may

cause the device to fall and

result in damage.

NOTE

While using “Smart Pianist”

with the instrument, all buttons

on the instrument cannot be

used. Control the instrument

by using “Smart Pianist.”

Playback/Recording of Audio Data (USB Audio Interface)

NOTE

The volume of the audio sound

input can be adjusted from a

computer or a smart device.

Default setting: On

NOTICE

If you are using a DAW

(digital audio workstation)

with this instrument, set the

Audio Loop Back to OFF.

Otherwise, loud noises may

occur, depending on the

settings of the computer/

smart device or the

application software.

G#5 (On)

G5 (Off)

Highest key

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Backing up Data and Initializing the Settings

The following settings and data are maintained even if you turn the power off.

Among the data listed above, only User Song data (USERSONG00.MID) can be

transferred to a computer and saved as an SMF file. For details, refer to the

“Computer-related Operations” on the website (page 9).

With this operation, all data (with the exception of the Songs) will be reset to the

factory default settings.

To do this, simultaneously hold down the C7 (the highest) key and turn on the

power.

You can confirm the firmware version of your instrument by audible voice in English.

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously, press the B0 key.

About the latest Firmware Version

Yamaha may from time to time update firmware of the product without notice for improvement. Make sure

to check our website for information of the latest release and upgrade the firmware for your instrument.

Data Maintained When Power is Turned Off

•Metronome Volume

• Metronome Beat (time signature)

• Touch Sensitivity

•Tuning

• Intelligent Acoustic Control Depth

• Intelligent Acoustic Control On/Off

• Stereophonic Optimizer On/Off

• Operation Confirmation Sounds On/Off

• Auto Power Off Enable/Disable

•Speaker On/Off

•User Song data

• Song data (SMF files) transferred from a computer

Saving User Song data to a computer

NOTICE

Saved data may be lost due

to malfunction or incorrect

operation. Save important

data to an external device

such as a computer.

Initializing the Settings

NOTICE

Never turn off the power

while the Initialize operation

is being executed (that is,

while the [REC], [PLAY], [+R]

and [–L] lamps are flashing).

NOTE

If this instrument somehow

becomes disabled or

malfunctions, turn off the

power then execute

Initialization.

Highest key

Confirming the firmware version of this instrument

Lowest key

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Appendix

Troubleshooting

Problem Possible Cause and Solution

Power suddenly and unexpectedly turns off.

This is normal and the Auto Power Off function may have been activated

(page 15). If desired, disable the Auto Power Off function.

The instrument does not turn on.

The plugs are not properly connected. Make sure that the DC plug is

securely inserted into the DC IN jack on the instrument, and that the AC

plug is securely inserted to the AC outlet (page 14).

A click or pop is heard when the power is

turned on or off.

This is normal when electrical current is being applied to the instrument.

Noise is heard from the speakers or

headphones.

The noise may be due to interference caused by the use of a mobile phone

in close proximity to this instrument. Turn off the mobile phone, or move it

further away from this instrument.

Noise is heard from the instrument’s speakers or

headphones when using the instrument with a

smart device, such as an iPhone/iPad.

When you use the instrument along with the application on your smart

device, we recommend that you set “Airplane Mode” to “ON” on your smart

device in order to avoid noise caused by communication. While Bluetooth

is connected, setting “Airplane Mode” to “ON” disconnects Bluetooth;

however, the connection can be restored by reconnecting again.

The overall volume is low, or no sound is heard.

The Master Volume is set too low. Set it to an appropriate level using the

[MASTER VOLUME] knob (page 11).

Make sure a pair of headphones or conversion adaptor is not connected to

the [PHONES] jack (page 15).

The Speaker setting is “Off.” Set the Speaker to “Normal” or “On” (page 15).

Make sure that Local Control is On. For details, refer to the “MIDI

Reference” (page 9).

Pedals do not function.

The pedal cord may not be securely connected to the [TO PEDAL] jack. Be

sure to insert the pedal cord all the way until the metal part of the cord plug

disappears from view (pages 36, 39).

The damper pedal does not function as

expected.

The damper pedal was pressed when the power was turned on. This is not

a malfunction; release the pedal and press it again to reset the function.

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Keyboard Stand Assembly

CAUTION

• Be careful not to confuse parts, and be sure to install all

parts in the correct orientation. Please assemble the unit in

accordance with the sequence given below.

• Assembly should be carried out by at least two persons.

• Assemble the unit on a hard and flat floor with ample space.

• Be sure to use the correct screw size, as indicated below.

Use of incorrect screws can cause damage.

• Be sure to tighten all screws upon completing assembly of

the unit.

• To disassemble, reverse the assembly sequence given

below.

Keyboard Stand Assembly

After completing the assembly, please

check the following.

• Are there any parts left over?

Review the assembly procedure and correct any errors.

• Is the instrument clear of doors and other

movable fixtures?

Move the instrument to an appropriate location.

• Does the instrument make a rattling noise

when you shake it?

Tighten all screws.

• Does the pedal box rattle or give way when you

step on the pedals?

Turn the adjuster so that it is set firmly against the floor.

• Are the pedal and power cords inserted

securely into the sockets?

Check the connection.

When Moving the Instrument After

Assembly

CAUTION

• When moving the instrument after assembly, always hold

the bottom of the main unit.

• Do not hold the key cover or top portion. Improper handling

can result in damage to the instrument or personal injury.

NOTICE

Rotate the adjuster under the pedal until it separates from the

floor surface. Contact with the adjuster can result in damage

to the floor surface.

Transporting

If you move to another location, you can transport the

instrument along with other belongings. You can move

the unit as it is (assembled), or you can disassemble the

unit down to the condition it was in when you first took

it out of the box. Transport the keyboard horizontally. Do

not lean it up against a wall or stand it up on its side. Do

not subject the instrument to excessive vibration or

shock. When transporting the assembled instrument,

make sure all screws are properly tightened and have not

been loosened by moving the instrument.

Assembly Precautions

Have a Phillips-head (+) screwdriver of the appropriate size

ready.

Reference page

YDP-164, YDP-144 page 34

YDP-S54 page 37

CAUTION

If the unit creaks or is otherwise unsteady when you play

on the keyboard, refer to the assembly instructions and

retighten all screws.

Do not hold here.

Hold here.

Separate the adjuster

from the floor surface.

Key cover

Top portion

Keyboard Stand Assembly

YDP-164, YDP-144, YDP-S54 Owner’s Manual

The illustrations here are taken from the YDP-144.

Remove all parts from the package and make sure you

have all of the items.

Remove foamed styrol pads from the package, position them on

the floor, then place A on top of them. Position the pads so that

they will not hide the speaker covers on the bottom of A.

* The adaptor may not be included, or may look different from the

illustration above, depending on your particular area. Please

check with your Yamaha dealer.

1. After untying the bundled pedal

cord on C, attach C to D and E and

fasten the screws (1-3).

1-1 Untie and straighten out the bundled pedal

cord.

1-2 Align D and E with each end of C.

1-3 Attach D and E to C by finger-tightening

the long screws (6 x 20 mm).

2. Attach B.

Depending on the model of digital piano you

purchased, the surface color of one side of B may

be different from the other side. In this case,

position B so that the side of the surface color

similar to D and E faces the player.

2-1

Place the lower side of B on each foot of D

and E, then attach the upper side to D and E.

2-2 Attach the top of B to D and E by finger-

tightening the thin screws (4 x 12 mm).

2-3 While pressing on the lower part of D and E

from the outside, secure the bottom ends of

B using two tapping screws (4 x 20 mm).

YDP-164, YDP-144 Assembly

Bundled pedal cord inside

AC adaptor

(YDP-164)

Power cord

(YDP-164)

AC adaptor

(YDP-144)

Cord holder

Speaker cover Speaker coverFoamed styrol pads

6 x 20 mm long screws x 4

6 x 16 mm short screws x 4

4 x 20 mm tapping screws

x 4

4 x 12 mm thin screws x 2

Caps x 4

Headphone hanger set (YDP-164 only)

4×10 mm thin screws

Headphone hanger

Untie the two vinyl strings.

Keyboard Stand Assembly

YDP-164, YDP-144, YDP-S54 Owner’s Manual

2-4 Insert the other two tapping screws (4 x 20

mm) into the other two screw holes to

secure B.

2-5 Securely tighten the screws on the top of B

that were attached in Step 2-2.

3. Secure C.

3-1 Securely tighten the screws on C that were

attached in Step 1-3.

3-2 Attach the caps to the head of the screws.

4. Mount A.

Be sure to place your hands at least 10 cm from

either end of A when positioning it.

CAUTION

• Fingers can become pinched between the main unit and the

rear or side panels, be extra careful so as not to drop the

main unit.

• Do not hold the keyboard in any position other than the

position shown in the illustration.

5. Secure A.

5-1 Adjust the position of A so that the left and

right ends of A will project beyond D and E

equally when seen from the front.

5-2 Secure A by tightening the short screws (6 x

16 mm) from the front.

2, 2

Place the

bottom ends

of the rear

panel on

each foot.

At least

10 cm

At least

10 cm

Projection of A

Keyboard Stand Assembly

YDP-164, YDP-144, YDP-S54 Owner’s Manual

6. Connect the pedal cord and the AC

adaptor.

6-1 Insert the pedal cord plug to the

[TO PEDAL] jack from the rear.

6-2

Securely wind the cord holder around the

pedal cord.

The cord holder is attached to D.

6-3 Insert the AC adaptor plug into the DC IN

jack from the rear.

7. Set the adjuster.

Rotate the adjuster until it comes in firm contact

with the floor surface.

(YDP-164 only)

8. Attach the headphone hanger.

Use the included two screws (4 x 10 mm) to attach

the hanger as shown in the illustration.

NOTICE

Do not hang anything other than the headphones on the

hanger. Doing so may damage this instrument or the hanger.

Insert the pedal cord securely until the metal part of the

cord plug disappears from view. Otherwise, the pedal may

not function properly.

After completing the assembly, make sure to confirm the

list of post-assembly questions on page 33.

Keyboard Stand Assembly

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Remove all parts from the package and make sure you

have all of the items.

Remove foamed styrol pads from the package, position them on

the floor, then place A on top of them. Position the pads so that

they will not hide the connector panel on the bottom of A.

* The two anti-fall brackets are identical. (Either one can be used

for left or right.)

* The adaptor may not be included, or may look different from the

illustration above, depending on your particular area. Please

check with your Yamaha dealer.

Attach (finger-tighten) C to D and E.

1-1 Untie and straighten out the bundled pedal

cord.

Don’t discard the vinyl tie. You will need it later in

step 7.

1-2 Align D and E with each end of C.

1-3 Attach D and E to C by finger-tightening

the long screws (6 x 20 mm).

2. Attach B.

Depending on the model of digital piano you

purchased, the surface color of one side of B may

be different from the other side. In this case,

position B so that the side of the surface color

similar to D and E faces the player.

2-1 Attach the top of B to D and E by finger-

tightening the two thin screws (4 x 12 mm).

2-2 While pressing on the lower part of D and E

from the outside, attach the anti-fall

brackets and then secure the bottom ends

of B using four long screws (6 x 25 mm).

2-3 Insert the other two tapping screws (4 x 20

mm) into the other two screw holes to

secure B.

2-4 Securely tighten the screws on the top of B

that were attached in Step 2-1.

CAUTION

Be sure to attach the anti-fall brackets to the instrument, to

ensure stability. Failure to do so might result in damage to the

instrument or even injury.

YDP-S54 Assembly

Bundled pedal cord inside

6 x 25 mm long screws x 4

Caps x 2

AC adaptor x 1

Anti-fall brackets x 2

6 x 20 mm long screws x 2

6 x 16 mm short screws x 4

4 x 12 mm thin screws x 4

4 x 20 mm tapping screws x 2

Cord holder

Power cord x 1

Connector panel

Foamed styrol pads

1-2

1-3

2-1, 2-4

2-3

2-2

Secure the anti-fall brackets using the screws.

Keyboard Stand Assembly

YDP-164, YDP-144, YDP-S54 Owner’s Manual

3. Secure C.

3-1 Securely tighten the screws on C that were

attached in Step 1-3.

3-2

Attach the caps to the head of the screws.

4. Mount A.

Be sure to place your hands at least 10 cm from

either end of A when positioning it.

Align the dowels on D and E with the corresponding holes

on the bottom of A.

CAUTION

• Be careful not to pinch your fingers or drop the unit.

• Make sure to keep your hands more than 10 cm distant from

the ends of A when positioning the unit, to avoid pinching

your fingers.

• Do not hold the keyboard in any position other than the

position shown in the illustration.

5. Secure A.

5-1 Adjust the position of A so that the left and

right ends of A will project beyond D and E

equally when seen from the front.

5-2 Secure A by tightening the short screws (6 x

16 mm) from the bottom.

6. Secure F.

Position F so that the side without felt faces the

player. Secure F by tightening two thin screws (4 x

12 mm).

3-2

3-1

At least

10 cm

At least

10 cm

5-1

5-2

Projection of A

Felt

Rear of F

Keyboard Stand Assembly

YDP-164, YDP-144, YDP-S54 Owner’s Manual

7. Connect the pedal cord.

7-1 Insert the pedal cord plug to the

[TO PEDAL] jack from the rear.

7-2

Securely wind the cord holder around the

pedal cord.

The cord holder is attached to D.

7-3 Use a vinyl tie (Step 1-1) to take up any

slack in the pedal cord.

8. Connect the AC adaptor.

8-1 Connect one end of the power cord to the

power adapter.

8-2 Insert the AC adaptor plug into the DC IN

jack from the rear.

9. Set the adjuster.

Rotate the adjuster until it comes in firm contact

with the floor surface.

Insert the pedal cord securely

until the metal part of the cord

plug disappears from view.

Otherwise, the pedal may not

function properly.

7-1

7-2

7-3

After completing the assembly, make sure to confirm the

list of post-assembly questions on page 33.

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Specifications

YDP-164 YDP-144 YDP-S54

Product Name Digital Piano

Size/Weight

Width 1,357 mm [53-7/16"] 1,353 mm [53-1/4"]

Height

849 mm [33-27/64"]

(With music rest raised:

1,003 mm [39-31/64"])

815 mm [32-1/16"]

(With music rest raised:

969 mm [38-1/8"])

792 mm [31-3/16"]

(Key cover open:

976 mm [38-27/64"])

Depth 422 mm [16-5/8"]

309 mm [12-11/64"]

(Key cover open:

317 mm [12-15/32"])

*With anti-fall brackets attached,

the depth is 404 mm [15-57/64"].

Weight 42.0 kg (92 lbs., 10 oz.) 38.0 kg (83 lbs., 12 oz.) 40.0 kg (88 lbs., 3 oz.)

Control

Interface

Keyboard

Number of Keys 88

Type

GH3 (Graded Hammer 3)

keyboard with synthetic ebony

and ivory keytops

GHS (Graded Hammer

Standard) keyboard with

matte black keytops

GH3 (Graded Hammer 3)

keyboard with synthetic ebony

and ivory keytops

Touch Response Hard/Medium/Soft/Fixed

Pedal

Number of Pedals 3

Half Pedal Yes (Damper)

Functions Damper, Sostenuto, Soft

Panel Language English

Cabinet

Key Cover Style Sliding Folding

Music Rest Yes

Voices

Tone Generation Piano Sound Yamaha CFX

Piano Effect

Damper Resonance Yes

Key-off Samples Yes

String Resonance Yes

Smooth Release Yes — Yes

Polyphony (max.) 192

Preset Number of Voices 10

Effects

Types

Reverb 4 types

Intelligent Acoustic

Control (IAC)

Yes

Stereophonic Optimizer

Yes

Functions

Dual Yes

Duo Yes

Recording/

Playback

(MIDI data

only; audio not

supported.)

Preset

Number of Preset

Songs

10 Voice Demo Songs, 50 Classics

Recording

Number of Songs 1

Number of Tracks 2

Data Capacity Approx. 100 KB/Song (approx. 11,000 notes)

Format

Playback SMF (Format 0, Format 1)

Recording SMF (Format 0)

Functions Overall Controls

Metronome Yes

Tempo Range 5 – 280

Transpose -6 – 0 – +6

Tuning 414.8 – 440.0 – 466.8 Hz (approx. 0.2 Hz increments)

USB audio interface Yes

Storage and

Connectivity

Storage

Internal Memory

(USER Drive)

Total maximum size approx. 900 KB

(User song: One song approx. 100 KB Loading song data from a computer: Up to 10 songs)

Connectivity

DC IN 16V 12V 16V

Headphones

Headphones/Output

Standard stereo phone jack (x 2)

USB TO HOST Yes

Sound System

Amplifiers 20W × 2 8W × 2 20W × 2

Speakers 12cm × 2

Power Supply

AC Adaptor

PA-300C (or an equivalent

recommended by Yamaha)

PA-150 (or an equivalent

recommended by Yamaha)

PA-300C (or an equivalent

recommended by Yamaha)

Power Consumption

13W (When using PA-300C

AC adaptor)

9W (When using PA-150 AC

adaptor)

13W (When using PA-300C

AC adaptor)

Auto Power Off Yes

Specifications

YDP-164, YDP-144, YDP-S54 Owner’s Manual

* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download

the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.

Included Accessories

(*Included or optional depending on locale.)

Owner’s Manual

Quick Operation Guide

50 Classical Music Masterpieces (Music Book)

AC adaptor: PA-300C or an

equivalent*, Power cord*

AC adaptor: PA-150 or an

equivalent*

AC adaptor: PA-300C or an

equivalent*, Power cord*

Bench* —

Warranty*

Online Member Product Registration

Separately Sold Accessories

(May not be available depending on your area.)

• HPH-150/100/50 headphones

• AC adaptor PA-300C or an

equivalent recommended

by Yamaha

• UD-BT01 Wireless MIDI

adaptor

• HPH-150/100/50 headphones

• AC adaptor: PA-150 or an

equivalent recommended

by Yamaha

• UD-BT01 Wireless MIDI

adaptor

• HPH-150/100/50 headphones

• AC adaptor PA-300C or an

equivalent recommended

by Yamaha

• UD-BT01 Wireless MIDI

adaptor

YDP-164 YDP-144 YDP-S54

YDP-164, YDP-144, YDP-S54 Owner’s Manual

Index

Numerics

50 Preset Songs ...........................................................26

AC adaptor .................................................................14

Accessories ....................................................................9

Assembly .....................................................................33

Audio Loop Back ........................................................30

Auto Power Off ...........................................................15

Backing up Data ..........................................................31

Beat .............................................................................19

Computer ...................................................................30

Computer-related Operations .......................................9

Damper Pedal .............................................................17

Damper Resonance .....................................................17

Delete ..........................................................................29

Demo Song List ...........................................................21

Demo Songs ................................................................21

Dual mode ..................................................................24

Duo .............................................................................25

Firmware version ........................................................31

Half-pedal ...................................................................17

Headphones ................................................................15

Hz (Hertz) ...................................................................23

Initializing ...................................................................31

Intelligent Acoustic Control (IAC) .............................16

Key Cover ............................................................ 12, 13

Left-hand Part .............................................................27

Manuals ........................................................................9

Metronome .................................................................19

MIDI Basics ..................................................................9

MIDI Reference ............................................................9

Music Rest ........................................................... 12, 13

Octave ........................................................................24

Operation Confirmation Sounds ................................18

Panel Controls and Terminals ....................................10

Pedals .........................................................................17

Pitch ........................................................................... 23

Playback .....................................................................26

Power ......................................................................... 14

Power indicator ..........................................................14

Practice ....................................................................... 27

Preset Songs ...............................................................26

Quick Operation Guide ................................................ 9

Quick Play ..................................................................27

Recording ...................................................................28

Reverb ........................................................................22

Reverb Depth .............................................................22

Reverb Type ...............................................................22

Reverb Type List .........................................................22

Right-hand Part ..........................................................27

Smart Device ..............................................................30

Smart Device Connection Manual ............................... 9

Smart Pianist ................................................................ 9

Soft Pedal ...................................................................17

Song ...........................................................................26

Sostenuto Pedal ..........................................................17

Speaker .......................................................................15

Stereophonic Optimizer .............................................15

Tempo ........................................................................19

Time signature ...........................................................19

Touch Sensitivity ........................................................18

Transpose ...................................................................23

Tuning ........................................................................23

USB Audio Interface ..................................................30

USB TO HOST .....................................................11, 30

User Song ...................................................................28

Voice .......................................................................... 20

Voice List ...................................................................20

Volume .................................................................11, 19

YDP-164, YDP-144, YDP-S54 Owner’s Manual

MEMO

(weee_eu_en_02)

(weee_eu_fr_02)

(weee_eu_es_02)

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic

products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in

accordance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative

effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste

disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further

information.

Information on Disposal in other Countries outside the European Union:

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local

authorities or dealer and ask for the correct method of disposal.

Informations concernant la collecte et le traitement des déchets d’équipements électriques et électroniques

Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou

électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.

Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et

électroniques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation

nationale.

En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la

sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui

pourraient advenir lors d'un traitement inapproprié des déchets.

Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et

électroniques, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où

vous avez acheté les produits.

Pour les professionnels dans l'Union européenne :

Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques, veuillez contacter votre

vendeur ou fournisseur pour plus d'informations.

Informations sur la mise au rebut dans d'autres pays en dehors de l'Union européenne :

Ce symbole est seulement valable dans l'Union européenne. Si vous souhaitez vous débarrasser de déchets

d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander

la méthode de traitement appropriée.

Información para usuarios sobre la recogida y eliminación de los equipos antiguos

Este símbolo en los productos, embalajes y documentos anexos significa que los productos eléctricos y electrónicos

no deben mezclarse con los desperdicios domésticos normales.

Para el tratamiento, recuperación y reciclaje apropiados de los productos antiguos, llévelos a puntos de reciclaje

correspondientes, de acuerdo con la legislación nacional.

Al deshacerse de estos productos de forma correcta, ayudará a ahorrar recursos valiosos y a impedir los posibles

efectos desfavorables en la salud humana y en el entorno que de otro modo se producirían si se trataran los

desperdicios de modo inapropiado.

Para obtener más información acerca de la recogida y el reciclaje de los productos antiguos, póngase en contacto

con las autoridades locales, con el servicio de eliminación de basuras o con el punto de venta donde adquirió los

artículos.

Para los usuarios empresariales de la Unión Europea:

Si desea desechar equipos eléctricos y electrónicos, póngase en contacto con su vendedor o proveedor para obtener

más información.

Información sobre la eliminación en otros países fuera de la Unión Europea:

Este símbolo solo es válido en la Unión Europea. Si desea desechar estos artículos, póngase en contacto con las

autoridades locales o con el vendedor y pregúnteles el método correcto.

MEMO

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha

ou au distributeur le plus proche de vous figurant dans la liste suivante.

Para detalles sobre productos, contacte su tienda Yamaha más

cercana o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Toronto, Ontario M1S 3R1,

Canada

Tel: +1-416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620,

U.S.A.

Tel: +1-714-522-9011

MEXICO

Yamaha de México, S.A. de C.V.

Av. Insurgentes Sur 1647 Piso 9, Col. San José

Insurgentes, Delegación Benito Juárez, México,

D.F., C.P. 03900, México

Tel: +52-55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B –

Vila Olímpia – CEP 04551-010 – São Paulo/SP,

Brazil

Tel: +55-11-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.,

Sucursal Argentina

Olga Cossettini 1553, Piso 4 Norte,

Madero Este-C1107CEK,

Buenos Aires, Argentina

Tel: +54-11-4119-7000

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Edificio Torre Davivienda, Piso: 20

Avenida Balboa, Marbella, Corregimiento de Bella

Vista, Ciudad de Panamá, Rep. de Panamá

Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND

Yamaha Music Europe GmbH (UK)

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, U.K.

Tel: +44-1908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH, Branch

Switzerland in Thalwil

Seestrasse 18a, 8800 Thalwil, Switzerland

Tel: +41-44-3878080

AUSTRIA/CROATIA/

CZECH REPUBLIC

HUNGARY/ROMANIA/SLOVAKIA/

SLOVENIA

Yamaha Music Europe GmbH, Branch Austria

Schleiergasse 20, 1100 Wien, Austria

Tel: +43-1-60203900

POLAND

Yamaha Music Europe GmbH

Sp.z o.o. Oddział w Polsce

ul. Wielicka 52, 02-657 Warszawa, Poland

Tel: +48-22-880-08-88

BULGARIA

Dinacord Bulgaria LTD.

Bul.Iskarsko Schose 7 Targowski Zentar Ewropa

1528 Sofia, Bulgaria

Tel: +359-2-978-20-25

MALTA

Olimpus Music Ltd.

Valletta Road, Mosta MST9010, Malta

Tel: +356-2133-2093

NETHERLANDS/BELGIUM/

LUXEMBOURG

Yamaha Music Europe, Branch Benelux

Clarissenhof 5b, 4133 AB Vianen, The Netherlands

Tel: +31-347-358040

FRANCE

Yamaha Music Europe

7 rue Ambroise Croizat, Zone d'activités de Pariest,

77183 Croissy-Beaubourg, France

Tel: +33-1-6461-4000

ITALY

Yamaha Music Europe GmbH, Branch Italy

Via Tinelli N.67/69 20855 Gerno di Lesmo (MB),

Italy

Tel: +39-039-9065-1

SPAIN/PORTUGAL

Yamaha Music Europe GmbH Ibérica, Sucursal

en España

Ctra. de la Coruña km. 17,200, 28231

Las Rozas de Madrid, Spain

Tel: +34-91-639-88-88

GREECE

Philippos Nakas S.A. The Music House

19th klm. Leof. Lavriou 190 02 Peania – Attiki,

Greece

Tel: +30-210-6686260

SWEDEN

Yamaha Music Europe GmbH Germany filial

Scandinavia

JA Wettergrensgata 1, 400 43 Göteborg, Sweden

Tel: +46-31-89-34-00

DENMARK

Yamaha Music Denmark,

Fillial of Yamaha Music Europe GmbH, Tyskland

Generatorvej 8C, ST. TH., 2860 Søborg, Denmark

Tel: +45-44-92-49-00

FINLAND

F-Musiikki Oy

Antaksentie 4

FI-01510 Vantaa, Finland

Tel: +358 (0)96185111

NORWAY

Yamaha Music Europe GmbH Germany -

Norwegian Branch

Grini Næringspark 1, 1332 Østerås, Norway

Tel: +47-6716-7800

ICELAND

Hljodfaerahusid Ehf.

Sidumula 20

IS-108 Reykjavik, Iceland

Tel: +354-525-5050

CYPRUS

Nakas Music Cyprus Ltd.

Nikis Ave 2k

1086 Nicosia

Tel: + 357-22-511080

Major Music Center

21 Ali Riza Ave. Ortakoy

P.O.Box 475 Lefkoşa, Cyprus

Tel: (392) 227 9213

RUSSIA

Yamaha Music (Russia) LLC.

Room 37, entrance 7, bld. 7, Kievskaya street,

Moscow, 121059, Russia

Tel: +7-495-626-5005

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

Yamaha Music Gulf FZE

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

TURKEY

Yamaha Music Europe GmbH

Merkezi Almanya Türkiye İstanbul Şubesi

Mor Sumbul Sokak Varyap Meridian Business

1.Blok No:1 113-114-115

Bati Atasehir Istanbul, Turkey

Tel: +90-216-275-7960

ISRAEL

RBX International Co., Ltd.

P.O Box 10245, Petach-Tikva, 49002

Tel: (972) 3-925-6900

OTHER COUNTRIES

Yamaha Music Gulf FZE

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co., Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: +86-400-051-7700

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: +852-2737-7688

INDIA

Yamaha Music India Private Limited

P-401, JMD Megapolis, Sector-48, Sohna Road,

Gurgaon-122018, Haryana, India

Tel: +91-124-485-3300

INDONESIA

PT. Yamaha Musik Indonesia (Distributor)

Yamaha Music Center Bldg. Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: +62-21-520-2577

KOREA

Yamaha Music Korea Ltd.

11F, Prudential Tower, 298, Gangnam-daero,

Gangnam-gu, Seoul, 06253, Korea

Tel: +82-2-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn. Bhd.

No.8, Jalan Perbandaran, Kelana Jaya, 47301

Petaling Jaya, Selangor, Malaysia

Tel: +60-3-78030900

SINGAPORE

Yamaha Music (Asia) Private Limited

Block 202 Hougang Street 21, #02-00,

Singapore 530202, Singapore

Tel: +65-6740-9200

TAIWAN

Yamaha Music & Electronics Taiwan Co., Ltd.

2F., No.1, Yuandong Rd., Banqiao Dist.,

New Taipei City 22063, Taiwan (R.O.C.)

Tel: +886-2-7741-8888

THAILAND

Siam Music Yamaha Co., Ltd.

3, 4, 15, 16th Fl., Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: +66-2215-2622

VIETNAM

Yamaha Music Vietnam Company Limited

15th Floor, Nam A Bank Tower, 201-203 Cach

Mang Thang Tam St., Ward 4, Dist.3,

Ho Chi Minh City, Vietnam

Tel: +84-28-3818-1122

OTHER ASIAN COUNTRIES

https://asia-latinamerica-mea.yamaha.com/

index.html

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 80 Market Street, South Melbourne,

VIC 3205 Australia

Tel: +61-3-9693-5111

NEW ZEALAND

Music Works LTD

P.O.BOX 6246 Wellesley, Auckland 4680,

New Zealand

Tel: +64-9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

https://asia-latinamerica-mea.yamaha.com/

index.html

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

DMI26

Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan

(For European Countries) Importer: Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany

https://www.yamaha.com/

Yamaha Global Site

http://download.yamaha.com/

Yamaha Downloads

Manual Development Group

Published 12/2018 MWMA*.*-**B0

VAN7260

Yamaha YDP-S54 de handleiding

Merk: Yamaha

Model: YDP-S54

Type: de handleiding

Deze handleiding is ook geschikt voor

Download PDF

rapport

in andere talen

English: Yamaha YDP-S54 Owner's manual
italiano: Yamaha YDP-S54 Manuale del proprietario
русский: Yamaha YDP-S54 Инструкция по применению
français: Yamaha YDP-S54 Le manuel du propriétaire
español: Yamaha YDP-S54 El manual del propietario
Deutsch: Yamaha YDP-S54 Bedienungsanleitung
português: Yamaha YDP-S54 Manual do proprietário
dansk: Yamaha YDP-S54 Brugervejledning
čeština: Yamaha YDP-S54 Návod k obsluze
polski: Yamaha YDP-S54 Instrukcja obsługi
română: Yamaha YDP-S54 Manualul proprietarului

Yamaha YDP-S54 de handleiding

Deze handleiding is ook geschikt voor

Yamaha YDP-S54 de handleiding

in andere talen

Gerelateerde artikelen