Yamaha YDP-223 Handleiding

Merk: Yamaha

Model: YDP-223

Categorie: Synthesizer

Type: Handleiding

Deze handleiding is ook geschikt voor

YDP223

YDP-223

Digital piano

Owner's Manual

Bedienungsanleitung

Mode d'emploi

Manual de instrucciones

Before using the YDP-223, be sure to read “Precautions„ on pages 6 -7.

Achten Sie darauf, vor Einsatz des YDP-223 die “Vorsichtsmassnahmen„

auf Seite 6-7 durchzulesen.

Avant d'utiliser le YDP-223, lire attentivement la section

«Precautions

d'usage» aux pages 6- 7.

Antes de utilizar el YDP-223, lea las

“Precauciones„ que debe tener en

cuenta en las páginas 6 - 7.

IMPORTANT

Check your power supply

Make sure that your local AC mains voltage matches the voltage specified

on the name plate on the bottom panel. In some areas a voltage selector

may be provided on the bottom panel of the main keyboard unit near the

power cord. Make sure that the voltage selector is set for the voltage in

your area. The voltage selector is set at 240V when the unit is initially

shipped. To change the setting use a "minus" screwdriver to rotate the

selector dial so that the correct voltage appears next to the pointer on the

panel.

WICHTIG

Überprüfung der Stromversorgung

Vergewissern Sie sich vor dem Anschließen an das Stromnetz, daß die

örtliche Netzspannung den Betriebsspannungswerten auf dem Typenschild

an der Unterseite des Instruments entspricht. In bestimmten

Verkaufsgebieten ist das Instrument mit einem Spannungswähler an der

Unterseite neben der Netzkabeldurchführung ausgestattet. Falls vorhanden,

muß der Spannungswähler auf die örtliche Netzspannung eingestellt

werden. Der Spannungswähler wurde werkseitig auf 240 V voreingestellt.

Zum Verstellen drehen Sie den Spannungsregler mit einem

Schlitzschraubendreher, bis der Zeiger auf den korrekten Spannungswert

weist.

IMPORTANT

Contrôler la source d'alimentation

Vérifiez que la tension spécifiée sur le panneau inférieur correspond à la

tension du secteur. Dans certaines régions, l'instrument peut être équipé

d'un sélecteur de tension situé sur le panneau inférieur du clavier à

proximité du cordon d'alimentation.

Vérifiez que ce selécteur est bien réglé en fonction de la tension secteur de

votre région. Le sélecteur de tension est réglé sur 240 V au départ d'usine.

Pour modifier ce réglage, utilisez un tournevis à lame plate pour tourner le

sélecteur afin de mettre l'indication correspondant à la tension de votre

région vis à vis du repère triangulaire situé sur le panneau.

IMPORTANTE

Verifique la alimentación de corriente

Asegúrese de que tensión de alimentación de CA de su área corresponde

con la tensión especificada en la placa de características del panel inferior.

En algunas zonas puede haberse incorporado un selector de tensión en el

panel inferior de la unidad del teclado principal, cerca del cable de

alimentación. Asegúrese de que el selector de tensión esté ajustado a la

tensión de su área. El selector de tensión se ajusta a 240V cuando la unidad

sale de fábrica. Para cambiar el ajuste, emplee un destornillador de cabeza

"recta" para girar el selector de modo que aparezca la tensión correcta al

lado del indicador del panel.

Introduction

92-469

(bottom)

SPECIAL MESSAGE SECTION

PRODUCT SAFETY MARKINGS:

Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these

graphics appears on this page. Please observe all cautions

indicated on this page and those indicated in the safety

instruction section.

See bottom of Keyboard enclosure for graphic symbol markings.

The exclamation point within the

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servic-

ing) instructions in the literature

accompanying the product.

The lightning ﬂash with arrowhead

symbol, within the equilateral trian-

gle, is intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product’s enclo-

sure that may be of sufﬁcient magni-

tude to constitute a risk of electrical

shock.

IMPORTANT NOTICE:

All Yamaha electronic products

are tested and approved by an independent safety testing

laboratory in order that you may be sure that when it is

properly installed and used in its normal and customary

manner, all foreseeable risks have been eliminated. DO

NOT modify this unit or commission others to do so

unless speciﬁcally authorized by Yamaha. Product perfor-

mance and/or safety standards may be diminished.

Claims ﬁled under the expressed warranty may be denied

if the unit is/has been modiﬁed. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE:

The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the speciﬁcations

without notice or obligation to update existing units.

ENVIRONMENTAL ISSUES:

Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is

approximately ﬁve years. When replacement becomes

necessary, contact a qualiﬁed service representative to

perform the replacement.

Warning:

Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice:

Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE:

Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the man-

ufacturer’s warranty, and are therefore the owners respon-

sibility. Please study this manual carefully and consult

your dealer before requesting service.

NAME PLATE LOCATION:

The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Model

Serial No.

Purchase Date

YDP-223

About this Owner’s Manual

ENGLISH

Thank you for purchasing the Yamaha YDP-223 Digital Piano! We recommend that you read this manual carefully so that

you can fully take advantage of the advanced and convenient functions of the YDP-223.

We also recommend that you keep this manual in a safe and handy place for future reference.

About this Owner’s Manual

This manual consists of three main sections: “Introduction,” “Reference” and “Appendix.”

Introduction (page 2):

Please read this section ﬁrst.

Reference (page 13):

This section explains how to make detailed settings for the YDP-223’s various functions.

Appendix (page 59):

This section introduces reference material.

*The illustrations and LED displays shown in this owner’s manual are for instructional purposes only and may appear

somewhat different from those on your instrument.

Trademarks:

•Apple and Macintosh are trademarks of Apple Computer, Inc.

•Windows is a registered trademark of Microsoft® Corporation.

•All other trademarks are the property of their respective holders.

YDP-223

Table of Contents

ENGLISH

Table of Contents

Introduction

SPECIAL MESSAGE SECTION ......................2

About this Owner’s Manual........................3

Application Index........................................5

PRECAUTIONS.............................................6

Accessories ..................................................8

Maintenance ...............................................8

Features.......................................................9

Before Using the YDP-223 ........................10

Key Cover .......................................................... 10

Music Rest ......................................................... 10

Turning the Power On...................................... 11

Setting the Volume............................................ 11

Using Headphones............................................ 12

Using the Speaker Switch.................................. 12

Reference

Part Names................................................14

Listening to the Demonstration Tunes ....16

Listening to 50 Piano Preset Songs ..........17

Practicing a One-Hand Part Using 50 Preset

Songs (Part Cancel Function) ...................... 18

A-B Repeat for 50 Preset Songs ........................ 20

Selecting & Playing Voices........................21

Selecting Voices................................................. 21

Using the Pedals ................................................ 21

Adding Variations to the Sound – [BRIL-

LIANCE]/[REVERB]/[EFFECT] ................. 22

Touch Sensitivity – [TOUCH] ......................... 24

Transposition – [TRANSPOSE]....................... 25

Combining Two Voices (Dual mode).............. 26

Using the Metronome....................................... 27

Recording Your Performance ...................28

Recording to [TRACK1]................................... 28

Re-recording TRACK1 ..................................... 29

Recording to [TRACK2]................................... 30

Changing the Initial Settings (Data recorded at

the beginning of a song) ............................... 31

Playing Back Recorded Songs...................32

Playing Back a Song .......................................... 32

Useful Playback Functions................................ 33

Detailed Settings – [FUNCTION].............. 34

Basic Procedure in Function Mode ..................35

About Each Function.........................................37

F1. Fine Tuning of the Pitch.......................37

F2. Selecting a Scale.....................................38

F3. Dual Mode Functions ...........................39

F4. Other Functions ....................................40

F5. Metronome Volume .............................40

F6. Preset Song Part Cancel Volume..........40

F7. MIDI Functions.....................................41

F8. Backup Functions..................................44

About MIDI............................................... 45

Connections ............................................. 46

Connectors.........................................................46

Connecting a Personal Computer ....................48

Troubleshooting....................................... 52

Options & Expander Modules.................. 52

Keyboard Stand Assembly ....................... 53

Preset Voice List ....................................... 56

Demo Song List ........................................ 56

Index......................................................... 57

Appendix

Factory Setting List .................................. 60

MIDI Data Format .................................... 61

MIDI Implementation Chart .................... 65

Specifications ........................................... 66

YDP-223

Application Index

ENGLISH

Application Index

Use this index to ﬁnd reference pages that may be helpful for your particular application and situation.

Listening

Listening to demo songs with different voices....................................... “Listening to the Demonstration Tunes” on page 16

Listening to songs from “50 Greats for the Piano” ...................................... “Listening to 50 Piano Preset Songs” on page 17

Listening to my recorded performance.................................................................“Playing Back Recorded Songs” on page 32

Playing

Using the three performance control pedals.............................................................................. “Using the Pedals” on page 21

Playing an accompaniment that matches pitch................................................“Transposition – [TRANSPOSE]” on page 25

Selecting a touch sensitivity type......................................................................... “Touch Sensitivity – [TOUCH]” on page 24

Fine tuning the pitch of the entire instrument when you play the YDP-223 along

with other instruments or CD music. ............................................................................ “Fine tuning of the pitch” on page 37

Changing voices

Viewing the list of voices..............................................................................................................“Preset Voice List” on page 56

Simulating a concert hall ..................................................................................................................... “[REVERB]” on page 22

Combining two voices............................................................................... “Combining Two Voices (Dual mode)” on page 26

Making the sound more brilliant or mellower ........................................................................... “[BRILLIANCE]” on page 22

Adding spread or swell to the sound .................................................................................................... “[EFFECT]” on page 23

Practicing

Muting the right- or left-hand part

...................................................... “Practicing a One-Hand Part Using 50 Preset Songs (Part Cancel Function)” on page 18

Practicing a speciﬁed phrase repeatedly..............................................................“A-B Repeat for 50 Preset Songs” on page 20

Practicing with an accurate and steady tempo .................................................................“Using the Metronome” on page 27

Practicing using your recorded song..................................................................... “Recording Your Performance” on page 28

Recording

Recording your performance................................................................................. “Recording Your Performance” on page 28

Settings

Adjusting the YDP-223 settings ..................................................................... “Detailed Settings – [FUNCTION]” on page 34

Connecting the YDP-223 to other devices

What is MIDI? ....................................................................................................................................“About MIDI” on page 45

Recording your performance....................................................................................................... “AUX OUT jacks” on page 46

Raising the volume....................................................................................................................... “AUX OUT jacks” on page 46

Outputting other instruments’ sound from the YDP-223 ............................................................. “AUX IN jacks” on page 47

Connecting a computer ..................................................................................“Connecting a Personal Computer” on page 48

Assembling

Assembling and disassembling the YDP-223 .............................................“Keyboard Stand Assembly” on pages page 53–55

YDP-223

PRECAUTIONS

ENGLISH

(1)B-7

1/2

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even

death from electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions

include, but are not limited to, the following:

●

Only use the voltage speciﬁed as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

●

Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it.

●

Use only the supplied power cord/plug.

●

Do not place the power cord near heat sources such as heaters

or radiators, and do not excessively bend or otherwise damage

the cord, place heavy objects on it, or place it in a position

where anyone could walk on, trip over, or roll anything over it.

●

Do not open the instrument or attempt to disassemble the inter-

nal parts or modify them in any way. The instrument contains no

user-serviceable parts. If it should appear to be malfunctioning,

discontinue use immediately and have it inspected by qualiﬁed

Yamaha service personnel.

●

Do not expose the instrument to rain, use it near water or in

damp or wet conditions, or place containers on it containing liq-

uids which might spill into any openings.

●

Never insert or remove an electric plug with wet hands.

●

Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

●

If the power cord or plug becomes frayed or damaged, or if

there is a sudden loss of sound during use of the instrument, or

if any unusual smells or smoke should appear to be caused by

it, immediately turn off the power switch, disconnect the electric

plug from the outlet, and have the instrument inspected by qual-

iﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or

others, or damage to the instrument or other property. These precautions include, but are not limited

to, the following:

●

When removing the electric plug from the instrument or an out-

let, always hold the plug itself and not the cord. Pulling by the

cord can damage it.

●

Remove the electric plug from the outlet when the instrument is

not to be used for extended periods of time, or during electrical

storms.

●

Do not connect the instrument to an electrical outlet using a

multiple-connector.

Doing so can result in lower sound quality, or possibly cause

overheating in the outlet.

●

Read carefully the attached documentation explaining the

assembly process.

Failure to assemble the instrument in the proper sequence

might result in damage to the instrument or even injury.

●

Do not expose the instrument to excessive dust or vibrations, or

extreme cold or heat (such as in direct sunlight, near a heater,

or in a car during the day) to prevent the possibility of panel dis-

ﬁguration or damage to the internal components.

●

Do not use the instrument in the vicinity of a TV, radio, stereo

equipment, mobile phone, or other electric devices. Otherwise,

the instrument, TV, or radio may generate noise.

●

Do not place the instrument in an unstable position where it

might accidentally fall over.

●

Before moving the instrument, remove all connected cables.

●

Do not place the instrument against a wall (allow at least 3 cm/

one-inch from the wall), since this can cause inadequate air cir-

culation, and possibly result in the instrument overheating.

Power supply/Power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/Power cord

Assembly

Location

YDP-223

PRECAUTIONS

ENGLISH

●

Before connecting the instrument to other electronic compo-

nents, turn off the power for all components. Before turning the

power on or off for all components, set all volume levels to mini-

mum. Also, be sure to set the volumes of all components at their

minimum levels and gradually raise the volume controls while

playing the instrument to set the desired listening level.

●

When cleaning the instrument, use a soft, dry or slightly damp

cloth. Do not use paint thinners, solvents, cleaning ﬂuids, or

chemical-impregnated wiping cloths.

●

Take care that the key cover does not pinch your ﬁngers, and do

not insert a ﬁnger or hand in any gaps on the key cover or

instrument.

●

Never insert or drop paper, metallic, or other objects into the

gaps on the key cover, panel or keyboard. If this happens, turn

off the power immediately and unplug the power cord from the

AC outlet. Then have the instrument inspected by qualiﬁed

Yamaha service personnel.

●

Do not place vinyl, plastic or rubber objects on the instrument,

since this might discolor the panel or keyboard.

●

Do not rest your weight on, or place heavy objects on the instru-

ment, and do not use excessive force on the buttons, switches

or connectors.

●

Do not operate the instrument for a long period of time at a high

or uncomfortable volume level, since this can cause permanent

hearing loss. If you experience any hearing loss or ringing in the

ears, consult a physician.

●

Do not place the bench in an unstable position where it might

accidentally fall over.

●

Do not play carelessly with or stand on the bench. Using it as a

tool or step-ladder or for any other purpose might result in acci-

dent or injury.

●

Only one person should sit on the bench at a time, in order to

prevent the possibility of accident or injury.

●

If the bench screws become loose due to extensive long-term

use, tighten them periodically using the included tool.

Saving and backing up your data

●

Depending upon the Backup Settings (page 44), internal data is

retained for about 1 week after the power is turned off. If the

period is exceeded, the data will be lost. Be sure to turn the

power switch on for a few minutes at least once a week. The

data could be lost due to malfunction or incorrect operation.

Save important data to external media such as the Yamaha

MDF3 MIDI data ﬁler.

Backing up the external media

●

To protect against data loss through media damage, we recom-

mend that you save your important data onto two external

media.

Always turn the power off when the instrument is not in use.

Connections

Maintenance

Handling caution

Using the bench (If included)

Saving data

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the instrument, or data that is lost or destroyed.

(1)B-7

2/2

YDP-223

Accessories / Maintenance

ENGLISH

Accessories

• “50 Greats for the Piano” (Music Book)

• Owner’s Manual

This manual contains complete instructions for operating your YDP-223.

• Bench

A bench may be included or optional, depending on your locale.

Maintenance

Clean the instrument using a dry or slightly damp soft cloth (wring well).

CAUTION

Do not use benzene, thinner, detergent, or chemically-treated cloth for cleaning. Do not place vinyl, plastic or rubber

products on the instrument.

Otherwise, the panel or keys may become discolored or degraded.

CAUTION

Before using the YDP-223, be sure to read “Precautions” on pages 6 – 7.

Tuning

Unlike an acoustic piano, the YDP-223 does not need to be tuned. It always stays perfectly in tune.

Transporting

If you move to another location, you can transport the YDP-223 along with your other belongings. You can move the

unit as it is (assembled) or you can disassemble the unit.

Tr ansport the keyboard horizontally. Do not lean it up against a wall or stand it up on its side. Do not subject the

instrument to excessive vibration or shock.

YDP-223

Features

ENGLISH

Features

The Yamaha YDP-223 Digital Piano offers unmatched sonic realism and natural grand-piano type playability as well as

Yamaha’s original “AWM Stereo Sampling” tone-generation technology for rich, musical voices, and a special “Graded

Hammer” keyboard that provides graded key weight and response throughout the keyboard range.

The YDP-223 Grand Piano 1 and 2 voices feature totally new samples painstakingly recorded from a full concert grand

piano.

PHONES

SPEAKER

NORMAL

OFF

HP. SW

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOICE

C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4

C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7

B-1A-1

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

GRAND

PIANO 1

CHURCH

ORGAN 1

E.PIANO

HARPSI-

CHORD 1

HARPSI-

CHORD 2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

CHURCH

ORGAN 2

STRINGS

JAZZ

ORGAN

VOICE

REVERB EFFECT TOUCH TRANSPOSE

SONG

POWER

AUX OUT AUX IN

L+R

LEVEL FIXED

R L

L+RRLR

PEDAL

TO HOST HOST SELECT

MIDI

THRU

MIDIMac

PC-2PC-1

OUT IN

This jack and selector switch allow direct con-

nection to a personal computer for sequencing

and other music applications (pages 48–51).

Delivers the output of the

YDP-223 for connection to

an instrument amplifier,

mixing console, PA sys-

tem, or recording equip-

ment (page 47).

Connect a MIDI device here to use

various MIDI functions (pages 41–43).

(About MIDI ➝ page 45)

Connect recording equipment (such

as a cassette tape recorder) here to

record your performance (page 46).

Connect the

pedal cord here

to use the YDP-

223’s pedals

(page 47).

A set of standard stereo

headphones can be plug-

ged in here for private

practice (page 12).

[MASTER VOLUME]

Adjust the volume

level using this slider

(page 11).

[METRONOME]

Control the metronome

functions (page 27).

The YDP-223 includes 50 preset songs.

This section enables you to listen to these songs, practice

using a convenient practice function, and record and play

back your performance (pages 17–20, 28–33).

TEMPO [▼] [▲]

You can change the song tempo (speed) and select

useful functions using this buttons (pages 34–44).

Voice buttons

Select voices from 14 internal sounds including

Grand Piano 1 and 2 (page 21). You can also

combine two voices at the same time (page 26).

[REVERB] / [EFFECT]

Add reverb (reverberation) and

effects to the sound (pages 22, 23).

[TRANSPOSE]

You can shift the pitch

of the entire keyboard

up or down so that the

pitch will match that of

another instrument or

singer, while you play

the same, unshifted

keys (page 25).

[TOUCH]

Fine-tune the

touch response

(page 24).

[DEMO]

Demonstration play-

back is available for

each voice (page 16).

[BRILLIANCE]

Adjust the brightness of the tone

using this slider (page 22).

This switch turns the

internal speakers on

or off (page 12).

YDP-223

Before Using the YDP-223

ENGLISH

Before Using the YDP-223

Key Cover

To open the key cover:

Lift the cover slightly, then push and slide it open.

To close the key cover:

Slide the cover toward you and gently lower the cover

over the keys.

CAUTION

Hold the cover with both hands when opening or closing it. Do not release it until it is fully opened or closed. Be care-

ful to avoid catching ﬁngers (yours or others, especially children’s) between the cover and main unit.

CAUTION

Do not place objects such as a piece of metal or paper on top of the key cover. Small objects placed on the key cover

may fall inside the unit when the cover is opened and may be nearly impossible to remove. This could cause electric

shock, short circuit, ﬁre or other serious damage to the instrument.

Music Rest

To raise the music rest:

1. Pull the music rest up and toward yourself as far as it will go.

2. Flip down the two metal supports at the left and right on

the rear of the music rest.

3. Lower the music rest so that it rests on the metal sup-

ports.

To lower the music rest:

1. Pull the music rest toward yourself as far as it will go.

2. Raise the two metal supports (at the rear of the music rest).

3. Gently lower the music rest backward until it is all the

way down.

CAUTION

Do not try to use the music rest in a half-raised position.

When lowering the music rest, do not release your hands

from the music rest until it is all the way down.

Be careful to avoid catching your fingers

when opening or closing the cover.

CAUTION

YDP-223 Before Using the YDP-223

ENGLISH

Turning the Power On

1. Connect the power cord.

Insert the plugs at the ends of the cord, one into the AC INLET on the YDP-223, and the other into a standard AC out-

let.

In some areas, a plug adaptor may be provided to match the pin conﬁguration of the AC wall outlets in your area.

(The shape of plug differs depending on locale.)

2. Turn the power on.

Press the [POWER] button.

•The display located in the center of the front panel and the power indicator located below the left end of the key-

board lights up.

When you’re ready to turn off the power, press the [POWER] button again.

•The display and the power indicator turn off.

Setting the Volume

Initially set the [MASTER VOLUME] control about halfway between the “MIN” and “MAX” settings. Then, when you start

playing, re-adjust the [MASTER VOLUME] control to the most comfortable listening level.

CAUTION

Do not use the YDP-223 at a high volume level for a long period of time, or your hearing may be damaged.

TIP

Power indicator

If you close the key cover without turning the power off, the power indicator remains lit, indicating that the

power is still on.

(bottom surface)

Power indicator

[POWER]

Normally indicates tempo.

Display

TERMINOLOGY

MASTER VOLUME:

The volume level of the entire keyboard sound

TIP

You can also adjust the [PHONES] output level and the AUX IN input level using the [MASTER VOLUME] slider.

MASTER VOLUME

MIN MAX

The level decreases. The level increases.

YDP-223 Before Using the YDP-223

ENGLISH

Using Headphones

Connect a pair of headphones to one of the [PHONES] jacks.

Two [PHONES] jacks are provided.

You can connect two sets of standard stereo headphones. (If you are

using only one pair of headphones, you can plug them into either

jack.)

Using the Headphone Hanger

A headphone hanger is included in the YDP-223 package so that you can hang

the headphones on the YDP-223. Install the headphone hanger using included

two screws (4 × 10mm) as shown in the ﬁgure.

CAUTION

Do not hang anything other than the headphones on the hanger. Otherwise,

the YDP-223 or the hanger may be damaged.

Using the Speaker Switch

This switch turns the internal speakers on or off.

NORMAL (HP. SW) ......... The speakers produce sound as long as a pair of headphones is not con-

nected.

ON ....................................... The speakers always produce sound.

OFF ...................................... The speakers produce no sound.

PHONES

SPEAKER

NORMAL

OFF

HP. SW

standard stereo

phone plug

bottom surface

PHONES

SPEAKER

NORMAL

OFF

HP. SW

YDP-223

ENGLISH

Reference

Part Names................................................................ 14

Listening to the Demonstration Tunes ................... 16

Listening to 50 Piano Preset Songs.......................... 17

Practicing a One-Hand Part Using 50 Preset Songs

(Part Cancel Function)............................................ 18

A-B Repeat for 50 Preset Songs .................................. 20

Selecting & Playing Voices ....................................... 21

Selecting Voices ........................................................... 21

Using the Pedals .......................................................... 21

Adding Variations to the Sound –[BRILLIANCE]/

[REVERB]/[EFFECT] ............................................. 22

Touch Sensitivity – [TOUCH].................................... 24

Tr ansposition – [TRANSPOSE]................................. 25

Combining Two Voices (Dual mode)......................... 26

Using the Metronome................................................. 27

Recording Your Performance................................... 28

Recording to [TRACK1] ............................................. 28

Re-recording TRACK1................................................ 29

Recording to [TRACK2] ............................................. 30

Changing the Initial Settings (Data recorded at the

beginning of a song)................................................ 31

Playing Back Recorded Songs .................................. 32

Playing Back a Song .................................................... 32

Useful Playback Functions.......................................... 33

Detailed Settings – [FUNCTION]........................... 34

Basic Procedure in Function Mode............................ 35

About Each Function .................................................. 37

F1. Fine Tuning of the Pitch ....................................... 37

F2. Selecting a Scale..................................................... 38

F3. Dual Mode Functions ........................................... 39

F4. Other Functions.................................................... 40

F5. Metronome Volume ................................................... 40

F6. Preset Song Part Cancel Volume .......................... 40

F7. MIDI Functions..................................................... 41

F8. Backup Functions ................................................. 44

About MIDI.............................................................. 45

Connections ............................................................. 46

Connectors .................................................................. 46

Connecting a Personal Computer .............................. 48

Troubleshooting....................................................... 52

Options & Expander Modules................................. 52

Keyboard Stand Assembly ....................................... 53

Preset Voice List........................................................ 56

Demo Song List........................................................ 56

Index......................................................................... 57

This section explains how to make detailed settings for the

YDP-223’s various functions.

YDP-223 Part Names

ENGLISH

Part Names

1 [POWER] ....................................... P11

2 [MASTER VOLUME] ....................... P11

3 [BRILLIANCE] ................................ P22

4 [DEMO] ........................................ P16

5 METRONOME [START/STOP] ........ P27

6 [TEMPO/FUNCTION #▲▼] ..... P27, 35

7 LED display ................................... P15

8 [–/NO] / [+/YES]

[PRESET]

[TRACK1] [TRACK2]

SONG [START/STOP]

[REC].......................... P17–20, P28–33

9 Voice buttons................................ P21

0 [REVERB] ....................................... P22

A [EFFECT] ....................................... P23

B [TOUCH]....................................... P24

C [TRANSPOSE]................................ P25

D AUX OUT...................................... P46

E AUX IN ......................................... P47

F [TO HOST]...............................P45–51

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

PHONES

SPEAKER

NORMAL

OFF

HP. SW

C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4

C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7

B-1A-1

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

GRAND

PIANO 1

CHURCH

ORGAN 1

E.PIANO

HARPSI-

CHORD 1

HARPSI-

CHORD 2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

CHURCH

ORGAN 2

STRINGS

JAZZ

ORGAN

VOICE

REVERB EFFECT TOUCH TRANSPOSE

SONG

POWER

7654

Top panel

YDP-223 Part Names

ENGLISH

Display

•Check the operation on the display in the center of the top panel as you proceed.

•The display indicates different values, as shown below, depending on the operation.

TRACK

START

STOP

REC

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

VOICE

REVERB EFFECT TOUCH TRANSPOSE

SONG

AUX OUT AUX IN

L+R

LEVEL FIXED

R L

L+RRLR

PEDAL

TO HOST HOST SELECT

MIDI

THRU

MIDIMac

PC-2PC-1

OUT IN

D E F G H I

G HOST SELECT .......................... P45–51

H MIDI [IN] [OUT] [THRU] .......... P45–51

I [PEDAL]......................................... P47

J [SPEAKER]...................................... P12

K [PHONES] ..................................... P12

L Soft (Left) Pedal............................. P22

M Sostenute (Center) Pedal............... P22

N Damper (Right) Pedal.................... P21

Connectors

Tempo

(Normal indication)

A song number of

“50 Greats for the Piano”

Function number Parameter value

YDP-223 Listening to the Demonstration Tunes

ENGLISH

Listening to the Demonstration Tunes

Demonstration tunes are provided that effectively demonstrate each of the YDP-223’s voices.

1. Turn the power on.

(In case the power is not turned ON) Press the [POWER] button.

When the power is turned ON, one of the voice button LEDs will light.

When you start playing, re-adjust the [MASTER VOLUME] control to the most

comfortable listening level.

2. Engage Demo mode.

Press the [DEMO] button to engage Demo mode. The voice button indicators

will ﬂash in sequence.

3. Play a Voice demo.

Press one of the voice buttons to start playback of all songs starting from the

corresponding voice demo tune — featuring the voice normally selected by that

voice button. (If you press the SONG [START/STOP] button instead of a voice

button, the GRAND PIANO 1 demo tune will begin playback.)

Adjust the volume/brilliance

Use the [MASTER VOLUME] control to adjust the volume and the [BRIL-

LIANCE]

control to adjust the brilliance (page 22).

4. Stop the Voice demo.

Press the SONG [START/STOP] button or the voice button of the currently-

playing demo to stop playback.

5. Exit from Demo mode.

Press the [DEMO] button to exit from Demo mode and return to normal play

mode.

The voice button indicators will stop ﬂashing in sequence.

425

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

Procedure

TIP

For a list of the demo songs,

see page 56.

NOTE

MIDI reception is not possible in

Demo Song mode.

Demo song data is not transmit-

ted via the MIDI connectors.

NOTE

Demo mode cannot be

engaged while a user song

recorder (page 28) or user song

playback (page 32) is in use.

TERMINOLOGY

Mode:

A mode is a status under which

you can execute a certain func-

tion. In Demo mode, you can

play back demonstration tunes.

NOTE

You cannot adjust the tempo of

demo songs.

You cannot use the part cancel

function (page 40) or the song

A–B repeat function (page 20)

in Demo mode.

YDP-223 Listening to 50 Piano Preset Songs

ENGLISH

Listening to 50 Piano Preset Songs

The YDP-223 provides performance data of 50 piano songs. You can simply listen to these songs

(page 17) or use them for practice (page 18). You can also refer to the included “50 Greats for the

Piano” that contains scores for 50 piano preset songs.

1. Engage Preset Song mode.

Press the [PRESET] button to engage Preset Song mode. The [PRESET],

[TRACK1] and [TRACK2] indicators will light.

2. Play any of the 50 preset songs.

2-1 Press the [–/NO], [+/YES] buttons to select the number

of the tune you want to play (the number will appear

on the LED display).

1 – 50: Select a preset song number and play only

the song.

ALL: Play all preset songs in sequence.

rnd: Play all preset songs continuously in random order.

2-2 Press the SONG [START/STOP] button to start playback.

Adjust the Volume

Use the [MASTER VOLUME] control to adjust the volume.

Adjust the tempo

You can use the [TEMPO/FUNCTION# ▼

▲]

buttons to adjust the playback tempo

as required. The default tempo can be

recalled by simultaneously pressing the

[▼] and [▲] buttons.

3. Stop playback.

Playback will stop automatically when the selected preset song has ﬁnished. To

stop the song during playback (or continuous playback), press the SONG

[START/STOP]

button.

•To play back another song continuously, see procedure 2 above.

-1

223

-2

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

Procedure

NOTE

Preset Song mode cannot be

engaged while the unit is in

Demo Song mode (page 16),

while a song is playing back

(page 32), or when the user song

recorder (page 28) is in use.

TERMINOLOGY

Song:

On the YDP-223, performance

data is called a “Song.” This

includes demonstration tunes

and piano preset tunes.

TIP

You can play the keyboard

along with the preset song. You

can change the voice playing on

the keyboard.

TIP

You can adjust the Brilliance

control (page 22) and Reverb

type (page 22) that is applied to

the voice you play on the key-

board and for the preset song

playback. You can change the

Effect type (page 23) and

Touch sensitivity (page 24) for

the keyboard voice.

NOTE

The default tempo “---” is auto-

matically selected whenever a

new preset song is selected, or

when playback of a new preset

song begins during “ALL” or

“rnd” playback.

NOTE

When you select a different song

(or a different song is selected

during chained playback), an

appropriate reverb type will be

selected accordingly.

song number

This produces a relative tempo vari-

ation, with a range from “–50”

through “---” to “50” at maximum;

the range will differ depending on

the selected song.

YDP-223 Listening to 50 Piano Preset Songs

ENGLISH

4. Exit from Preset Song mode.

Press the [PRESET] button to exit Preset Song mode. The indicator turns off,

and the unit returns to normal play mode.

How to use the practice functions

You can turn the left- and right-hand parts on or off as required so you can practice the

corresponding part (part cancel function) and continuously repeat a speciﬁed phrase

within a song (song A-B repeat function). For more information, see pages 18–20.

Practicing a One-Hand Part Using 50 Preset Songs

(Part Cancel Function)

The 50 preset songs have separate left- and right-hand parts on individual tracks. You can turn the

left- and right-hand parts on or off as required so you can practice the corresponding part (the part

that is turned off) on the keyboard. The right-hand part is played by [TRACK1] and the left-hand

part is played by [TRACK2].

1. Turn off the playback part you wish to practice.

After you select a song to practice, press the [TRACK1] or [TRACK2] button to

turn off the corresponding part.

When you ﬁrst select a song, both [TRACK1] and [TRACK2] indicators light up,

indicating that you can play back both parts. When you press one of the buttons

to turn off playback, the corresponding button indicator turns off and the cor-

responding part playback is muted.

•Pressing the buttons repeatedly toggles playback between on and off.

2. Start playback and playing.

Press the SONG [START/STOP] button to start playback. Play the part you just

turned off.

NOTE

MIDI reception is not possible in

Piano Song mode.

Piano song data is not transmit-

ted via the MIDI connectors.

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

Procedure

NOTE

The Preset Song Part Cancel

function cannot be used during

“ALL” or “rnd” (page 17) play-

back.

TIP

The parts can be turned on or

off even during playback.

TIP

The “Preset Song Part Cancel

Volume” function described on

page 40 can be used to set the

canceled part so that it plays at

a volume from “0” (no sound) to

“20”. The normal setting is “5”.

TERMINOLOGY

Normal setting:

The “Normal setting” refers to

the default setting (factory set-

ting) obtained when you ﬁrst

turn on the power to the YDP-

223.

YDP-223 Listening to 50 Piano Preset Songs

ENGLISH

Starting playback automatically as you start playing the keyboard

(Synchro Start)

When the Synchro Start function is engaged, play

back of the selected preset song will begin automati-

cally as soon as you start playing on the keyboard.

To engage the Synchro Start function press the

SONG [START/STOP]

button while holding the

part button for the ON part. A dot will appear in the

lower right corner of the display.

(Repeat the previous operation to disengage the Synchro Start function.)

Playback will then start as soon as you begin playing on the keyboard.

Left Pedal Start/Stop

The left pedal can be assigned to start and stop preset song playback via the “Left

Pedal Mode” function described on page 40.

Stop playback.

When playback is complete, it automatically stops and the YDP-223 locates the

top of the song. If you wish to stop playback in the middle of a song, press the

SONG[START/STOP]

button.

NOTE

If you hold a track button that is

OFF while pressing the

SONG

[START/STOP]

button, that

track will be turned ON and the

unit will engage Synchro Start

mode.

NOTE

Both parts are automatically

turned ON whenever a new

song is selected.

synchro start mark

song number

YDP-223

Listening to 50 Piano Preset Songs

ENGLISH

A-B Repeat for 50 Preset Songs

The A-B Repeat function can be used to continuously repeat a speciﬁed phrase within a preset song.

Combined with the Part Cancel function described below, this provides an excellent way to practice

difﬁcult phrases.

Specify the beginning (A) and the end (B) of the

phrase, and start practicing.

Select and play a preset song, then press the

[TEMPO/

FUNCTION#]

button at the beginning of the phrase

you want to repeat.

This sets the “A” point ( will appear on the dis-

play).

To specify the end (B) of the phrase, press the

[TEMPO/

FUNCTION#]

button a second time at the end of the

phrase.

This sets the “B” point ( will appear on the dis-

play).

At this point, repeat playback will begin between the

speciﬁed A and B points.

Stop playback.

Press the

SONG [START/STOP]

button to stop playback while retaining the

speciﬁed A and B points. A-B repeat playback will resume if you press the

SONG

[START/STOP]

button again.

To cancel the A and B points, press the

[TEMPO/FUNCTION#]

button once.

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

Procedure

NOTE

The A-B Repeat function cannot

be used during “ALL” or “rnd”

(page 17) playback.

NOTE

•To set the “A” point at the

very beginning of the song,

press the

[TEMPO/FUNC-

TION#]

button before start-

ing playback.

•To set the B point at the

song’s end, press the

[TEMPO/FUNCTION#]

but-

ton after song playback is

complete and before

disappears from the display.

TIP

An automatic lead-in (to help

guide you into the phrase)

starts at the A point of the song.

However, when the A point is

set at the beginning of the song,

the automatic lead-in is not

played.

NOTE

The A and B points are auto-

matically canceled when a new

song is selected.

YDP-223

Selecting & Playing Voices

ENGLISH

Selecting & Playing Voices

Selecting Voices

Select the desired voice by pressing one of the

[VOICE]

buttons.

Then, when you start playing, re-adjust the

[MASTER VOLUME]

control for the most

comfortable listening level.

Using the Pedals

The YDP-223 has three foot pedals that produce a range

of expressive effects similar to those produced by the

pedals on an acoustic piano.

Damper (Right) Pedal

The damper pedal functions in the same way as a

damper pedal on an acoustic piano. When the damper

pedal is pressed, notes sustain longer. Releasing the pedal

immediately stops (damps) any sustained notes.

Voice buttons

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

Procedure

TIP

To learn characteristics of the

voices, listen to demo songs for

each voice (page 16). Refer to

“Preset Voice List” on page 56

for more information on the

characteristics of each preset

voice.

TERMINOLOGY

Voice:

On the YDP-223, a voice means

a “tone” or “tonal color.”

TIP

You can control the loudness of

a voice by adjusting the force

with which you strike the keys,

although different playing styles

(touch sensitivities) have little or

no effect with certain musical

instruments.

Refer to “Preset Voice List” on

page 56.

NOTE

If the damper pedal doesn’t

work, make sure that the pedal

cord is properly plugged into the

main unit (page 54).















When you press the damper

pedal here, the notes you

play before you release the

pedal have a longer sustain.

YDP-223

Selecting & Playing Voices

ENGLISH

Sostenuto (Center) Pedal

If you play a note or chord on the keyboard and press the

sostenuto pedal while the note(s) are held, those notes

will sustain as long as you hold the pedal (as if the

damper pedal had been pressed) but all subsequently

played notes will not be sustained. This makes it possible

to sustain a chord, for example, while other notes are

played “staccato.”

Soft (Left) Pedal

The soft pedal reduces the volume and slightly changes the timbre of notes played while

the pedal is pressed. The soft pedal will not affect notes that are already playing when it

is pressed.

Adding Variations to the Sound – [BRILLIANCE]/

[REVERB]/[EFFECT]

[BRILLIANCE]

This control can be used to change the tonality or “timbre” of the sound output.

The control range is from MELLOW to BRIGHT.

[REVERB]

This control enables you to select various digital reverb effects that would add extra

depth and expression to the sound to create a realistic acoustic ambience.

OFF:

When no reverb effect is selected, no REVERB indicator is lit.

ROOM:

This setting adds a continuous reverb effect to the sound, similar to the

acoustic reverberation you would hear in a room.

HALL 1:

For a “bigger” reverb sound, use the HALL 1 setting. This effect simulates

the natural reverberation of a small-size concert hall.

HALL 2:

For a truly spacious reverb sound, use the HALL 2 setting. This effect simu-

lates the natural reverberation of a large concert hall.

STAGE:

Simulates the reverb of a stage environment.

Pressing the

[REVERB]

button repeatedly toggles the reverb on and off.

The indicators light in sequence each time the

[REVERB]

button is pressed. No effect is

produced when all indicators are off.

Even if the REVERB effect is OFF, a “Soundboard Reverb” effect will be applied when

the

GRAND PIANO 1

voice is selected.

Adjusting Reverb Depth

Adjust the reverb depth for the selected voice by using the

[–/NO] [+/YES] buttons while holding the [REVERB] but-

ton. The depth range is from 0 through 20. The current

depth setting appears on the LED display while the

[REVERB] button is held.

TIP

Organ, string and choir voices

will continue to sound for as

long as the sostenuto pedal is

depressed.















When you press the sostenu-

to pedal here while holding

the note, the note will sustain

as long as you hold the pedal.

TIP

The left pedal can be assigned

to song start/stop operation via

the “Left Pedal Mode” described

on page 40.

[BRILLIANCE]

[–/NO] [+/YES]

[EFFECT][REVERB]

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

NOTE

When the BRILLIANCE is set to

BRIGHT, the overall sound will

be slightly louder. If the MAS-

TER VOLUME is set at a high

level the sound may become

distorted. If so, lower the MAS-

TER VOLUME level.

TIP

The default reverb type (includ-

ing OFF) and depth settings are

different for each voice.

TIP

Releasing the [REVERB] but-

ton changes the reverb type.

If you are changing the reverb

depth by holding the [REVERB]

button, pressing the [REVERB]

button will not change the

reverb type.

Procedure

TIP

depth 0: no effect

depth 20: maximum reverb

depth

TIP

Default depth settings are differ-

ent for each voice.

depth

YDP-223 Selecting & Playing Voices

ENGLISH

[EFFECT]

The [EFFECT] button allows you to select an effect to give your

sound greater depth and animation.

OFF: When no effect is selected, no EFFECT indicator is lit.

CHORUS: A shimmering, broadening effect

PHASER: Adds a sweeping effect to the sound.

TREMOLO: Tremolo effect

DELAY: Echo effect

To select an effect type press the [EFFECT] button a few times until the indicator corre-

sponding to the desired type lights (the indicators light in sequence each time you press

the [EFFECT] button). No effect is produced when all indicators are off.

Adjusting Effect Depth

You can adjust the effect depth for the selected voice by

using the [–/NO] and [+/YES] buttons while holding the

[EFFECT] button.

The depth range is from 0 through 20. The current depth

setting appears on the LED display while the [EFFECT]

button is held.

TIP

The default effect type (includ-

ing OFF) and depth settings are

different for each voice.

Procedure

TIP

Releasing the [EFFECT] button

changes the effect type.

If you are changing the depth

settings by holding the

[EFFECT] button, pressing the

[EFFECT] button will not

change the effect type.

TIP

depth 0: no effect

depth 20: maximum effect

depth

TIP

Default depth settings are differ-

ent for each voice.

depth

YDP-223 Selecting & Playing Voices

ENGLISH

Touch Sensitivity – [TOUCH]

You can select four different types of keyboard touch sensitivity — HARD, MEDIUM, SOFT or FIXED

— to match different playing styles and preferences.

HARD: Requires that the keys be played quite hard to produce maximum loud-

ness.

MEDIUM: Produces a fairly “standard” keyboard response.

SOFT: Allows maximum loudness to be produced with relatively light key pres-

sure.

FIXED: All notes are produced at the same volume no matter how hard the key-

board is played.

You can adjust the volume.

To select a touch sensitivity type press the

[TOUCH] button a few times until the indica-

tor corresponding to the desired type lights (the indicators light in sequence each time

the [TOUCH] button is pressed). No indicator is lit when “FIXED” is selected.

Changing the volume when FIXED is selected

When you select FIXED, you can set the volume for notes

played in FIXED mode by using the [–/NO] and [+/YES] but-

tons while you hold the [TOUCH] button. The current vol-

ume level appears on the display. The volume range is from 1

through 127. The default setting is 64.

TIP

This setting does not change

the weight of the keyboard.

TIP

Normal setting = MEDIUM

TIP

The touch sensitivity type will

become the common setting for

all voices. However, the touch

sensitivity settings may have lit-

tle or no effect with certain

voices that are not normally

responsive to keyboard dynam-

ics. (Refer to the “Preset Voice

List” on page 56.)

[TOUCH]

[–/NO] [+/YES]

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

Procedure

TIP

1: minimum volume

127: maximum volume

TIP

The touch volume set in FIXED

mode will become the common

setting for all voices.

TIP

Releasing the [TOUCH] button

changes the touch type.

If you are changing the volume

by holding the [TOUCH] button,

pressing the [TOUCH] button

will not change the touch sensi-

tivity type. (FIXED mode will

remain selected.)

volume range

YDP-223 Selecting & Playing Voices

ENGLISH

Transposition – [TRANSPOSE]

The YDP-223’s Transpose function makes it possible to shift the pitch of the entire keyboard up or

down in semitone intervals to facilitate playing in difﬁcult key signatures, and to let you easily

match the pitch of the keyboard to the range of a singer or other instruments. For example, if you

set the transposition amount to “5,” playing key C produces pitch F. In this way, you can play a

song as though it were in C major, and the YDP-223 will transpose it to the key of F.

Use the [–/NO] and [+/YES] button while holding the

[TRANSPOSE]

button to transpose down or up as required.

The amount of transposition appears on the LED display

while the [TRANSPOSE] button is held. The default transpose

setting is “0”.

The [TRANSPOSE] button indicator remains lit when a transpose setting other than

“0” is selected. Every time the [TRANSPOSE] button is pressed after that switches the

transpose function ON or OFF.

[TRANSPOSE]

[–/NO] [+/YES]

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

Procedure

TERMINOLOGY

Transpose:

Changing the key signature of a

song. On the YDP-223, trans-

posing shifts the pitch of the

entire keyboard.

TIP

The transposition range:

–12: –12 semitones

(down one octave)

0: normal pitch

12: 12 semitones

(up one octave)

TIP

Notes below and above the A-1

…. C7 range of the YDP-223

sound one octave higher and

lower, respectively.

transposition

YDP-223 Selecting & Playing Voices

ENGLISH

Combining Two Voices (Dual mode)

You can play two voices simultaneously across the entire range of the keyboard. In this way, you

can simulate a melody duet or combine two similar voices to create a thicker sound.

1. Engage Dual mode.

Press two voice buttons at the same time (or press one voice button while hold-

ing another). The voice indicators of both selected voices will light when Dual

mode is active.

•According to the voice numbering

priority shown in the diagram on

the right, the lower value voice

number will be designated as Voice

1 (the other voice will be desig-

nated as Voice 2).

The YDP-223 Function mode provides access to a number of other Dual mode

functions, such as volume balance setting or octave setting (page 39). (If you do

not set Dual mode functions, the appropriate setting will be set in each voice by

default.)

2. Exit Dual mode and return to normal play mode.

To return to the normal single-voice play mode, press any single voice button.

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

Procedure

TIP

[REVERB] in Dual Mode

The reverb type assigned to

Voice 1 will take priority over the

other. (If the reverb is set to OFF,

Voice 2 reverb type will be in

effect.) Reverb depth setting via

the panel controls (i.e., pressing

the [–/NO] or [+/YES] buttons

while holding the [REVERB] but-

ton — see page 22) will be

applied only to Voice 1.

TIP

[EFFECT] in Dual Mode

Depending on the conditions,

one effect type may take priority

over the other. Depth will be

decided according to the depth

default value of the voice combi-

nation. However, using function

F3 (page 39) you can adjust the

depth value for each voice to

your liking.

Effect depth setting via the panel

controls (i.e., pressing the [–/

NO] or [+/YES] buttons while

holding the [EFFECT] button —

see page 23) will be applied only

to Voice 1.

Voice numbering priority

12 13 14

345 6 7

891011

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

VOICE

YDP-223 Selecting & Playing Voices

ENGLISH

Using the Metronome

The YDP-223 features a built-in metronome (a device that keeps an accurate tempo) that is conve-

nient for practicing.

1. Start the metronome.

The metronome sound is turned on by pressing

the METRONOME [START/STOP] button.

Adjusting the tempo

The tempo of the metronome and user song recorder playback (the recorder is

described in the next section) can be set from 32 to 280 beats per minute by

using the [TEMPO/FUNCTION# ▼, ▲] buttons (when the [TEMPO/FUNC-

TION# ▼, ▲]

button’s [TEMPO] indicator is lit).

Adjusting the time signature

The time signature (beat) of the metronome can be

set by using the [–/NO] and [+/YES] buttons while

holding the METRONOME [START/STOP] button.

You can set the beat to 0, 2, 3, 4, 5 or 6. The current

setting appears on the LED display while you are

holding the METRONOME [START/STOP] button.

2. Stop the metronome.

Turn off the metronome by pressing the METRONOME [START/STOP] button.

[TEMPO/FUNCTION# ▲▼]

[–/NO] [+/YES]

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

Procedure

The beat indicator flashes

at the current tempo.

TIP

If the [TEMPO/FUNCTION#]

button’s [FUNCTION#] indicator

is lit, press the [TEMPO/FUNC-

TION#] button to light the

[TEMPO] indicator.

TIP

The volume of the metronome

can be adjusted via the Metro-

nome Volume function in Func-

tion mode (page 40).

beat

YDP-223 Recording Your Performance

ENGLISH

Recording Your Performance

The ability to record and play back what you’ve played on the YDP-223

keyboard can be an effective practice aid. You can, for example, record just

the left-hand part, and then practice the right-hand part while playing back

the recorded left-hand part. Or, since you can record up to two tracks sepa-

rately, you could record the left- and right-hand parts separately, or record

both parts of a duet and hear how they sound when played back. The YDP-

223’s two-track Song Recorder allows the recording of one User Song.

Recording to [TRACK1]

CAUTION

Notes on recording

All user song recorder data will be retained in memory for about one week after the

power is turned off. If you want to keep your recorded data for longer periods of time,

turn the power on for a few minutes at least once a week.

It is also possible to store the data to an external MIDI storage device such as the Yamaha

MIDI Data Filer MDF3 by using the Bulk Data Dump function described on page 43.

1. Make all the initial settings.

Before you begin to record, select the voice you want to record (or voices if you

will be using Dual mode). Make any other desired settings (tempo, reverb, etc.)

as well. You might also want to set the volume.

You can also adjust the playback volume using [MASTER VOLUME].

2. Engage Record Ready mode.

Press the [REC] button to engage Record Ready mode.

Recording does not actually start yet.

The [TRACK1] or the [TRACK2] indicator ﬂashes in red.

The amount of memory available for recording will be

shown on the LED display in approximate kilobytes,

and the right-most dot on the LED display will ﬂash at

the current METRONOME tempo setting.

Record Ready mode can be disengaged before recording by pressing the [REC]

button a second time.

TIP

You can record your perfor-

mance (audio data) to a cas-

sette tape recorder or other

recording device via the AUX

OUT connector (page 46).

TERMINOLOGY

Recording vs. Saving:

The format of performance data

recorded on a cassette tape dif-

fers from that of data recorded on

the YDP-223. A cassette tape

records audio signals. The YDP-

223 “saves” information regard-

ing note timing, voices, and a

tempo value, but not audio sig-

nals. When you play back

recorded songs, the YDP-223

produces sound based on the

saved information. Therefore,

recording on the YDP-223 may

be more accurately called “sav-

ing information.” However, this

book often uses the word

“recording” because it seems to

make more sense.

43562

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

NOTE

When the unit is in Demo Song

or Preset Song mode, Record

mode cannot be engaged.

NOTE

To avoid erasing data from

the track:

Press the [TRACK1/2] button. If

the indicator lights up green, the

track already contains data.

Note that the existing data will

be erased if you record new

data on the track.

Procedure

NOTE

The amount of memory avail-

able for recording:

This value in KiloBytes (a unit

used of measurement for data)

indicates how much space

remains available for recording

on the YDP-223. You can record

up to a maximum of about 9,400

notes on the YDP-223 depending

on pedal usage and other factors.

flash

YDP-223 Recording Your Performance

ENGLISH

3. Select the record track.

When Record mode is engaged in the previous step, the last-recorded track will

automatically be selected for recording and its indicator — i.e. the [TRACK1] or

[TRACK2] button indicator — will glow red. If you want to record on a different

track, press the appropriate track button so that its indicator glows red.

4. Start recording.

Recording will begin automatically as soon as you play a note on the keyboard

or press the SONG [START/STOP] button. The current measure number will

appear on the display while recording.

5. Stop recording.

Press either the [REC] or SONG [START/STOP] button to stop recording.

The indicator of the recorded track will glow green to indicate that it now con-

tains data. (Record mode is disengaged automatically.)

6. Play back the recorded performance.

Press the SONG[START/STOP] button to play back the recorded performance.

To stop playback in the middle of a song, press the SONG[START/STOP] but-

ton.

Re-recording TRACK1

This section explains how to record again in case your performance was not satisfactory.

1. Select a voice or voices (and other settings) for recording, if necessary.

Repeat Step 1 on page 28 if you wish to change the previous settings.

2. Re-engage Record Ready mode.

Press the [REC] button, again.

The selected track’s indicator ﬂashes in red.

Follow the procedure from Step 4 on this page to re-record.

TIP

If the metronome was on when

you started recording, you’ll be

able to keep time with the met-

ronome while recording, but the

metronome sound will not be

recorded.

TIP

For more recording information,

see page 30.

TIP

The left pedal can be assigned

to start and stop recording via

the “Left Pedal Mode” function

described on page 40.

NOTE

The record track indicator will

begin to ﬂash when the recorder

memory is almost full. If the

memory becomes full during

recording, “FUL” will appear on

the display and recording will

stop automatically. (All recorded

data up to that point will be

retained.)

NOTE

Pressing the SONG [START/

STOP] button to start recording,

then pressing it again to stop

recording will erase all previ-

ously-recorded data on the

selected track.

TIP

If you want to change the

tempo, time signature, reverb

type, or effect type when re-

recording a track or when

recording to another track, do

so after you engage Record

Ready mode (step 2).

NOTE

You cannot re-record in the mid-

dle of a song.

YDP-223 Recording Your Performance

ENGLISH

Recording to [TRACK2]

This section explains how to record another part on the second track.

1. Select a voice or voices (and other settings) for the recording.

Select a voice (or voices) for recording. Select other settings, if necessary.

2. Re-engage Record Ready mode.

Press the [REC] button again.

The selected track’s indicator ﬂashes in red.

3. Select a recording track.

Select a track that you have not already used for recording. The selected track’s indi-

cator lights up red. (The indicator of a track that contains previously-recorded data

will glow green.)

You can record new sounds and notes on each pass while listening to the recorded

track.

Follow the procedure from Step 4 on page 29 to record.

The user song recorder records the following data:

Data in addition to the notes and voices you play is recorded.

This data includes “Individual Tracks” and “Entire Song.” See below.

Individual Tracks

•Notes played

•Voice selection

•Pedal (Damper/Soft/Sostenuto)

• [REVERB] depth

• [EFFECT] depth

•Dual mode voices

•Dual balance (F3)

•Dual detune (F3)

•Dual octave shift (F3)

Entire Song

•Tempo

•Time signature (beat)

• [REVERB] type (including OFF)

• [EFFECT] type (including OFF)

TIP

If you want to change the

tempo, time signature, reverb

type, or effect type when re-

recording a track or when

recording to another track, do

so after you engage Record

Ready mode (step 2).

NOTE

If you don’t want to hear the

previously-recorded track while

you record (for example, when

you want to record a song differ-

ent from what you recorded on

the previous track), press the

playback track button before

pressing the [REC] button (step

2, above) so that its indicator is

turned off.

YDP-223 Recording Your Performance

ENGLISH

Changing the Initial Settings (Data recorded at the

beginning of a song)

The initial settings (data recorded at the beginning of a song) can be changed after the recording.

For example, after recording, you can change the voice to create a different ambience or adjust the

song tempo to your taste.

You can change the following initial settings.

Individual Tracks

•Voice selection

• [REVERB] depth

• [EFFECT] depth

•Dual mode voices

Entire Song

•Tempo

•Time signature (beat)

• [REVERB] type (including OFF)

• [EFFECT] type (including OFF)

1. Engage Record mode and select a track to change the initial settings.

The indicator glows red. (Data shared by two tracks can be changed via either track.)

2. Change the settings via the panel controls.

For example, if you wish to change the recorded voice from [E. PIANO 1] to

[E. PIANO 2], press the [E. PIANO 2] button.

Be careful not to press the SONG [START/STOP] button or a key on the keyboard,

either of which will start recording and erase all previously-recorded data on the

selected track.

3. Press the [REC] button to exit Record mode.

Be careful not to press the SONG [START/STOP] button or a key on the keyboard,

either of which will start recording and erase all previously-recorded data on the

selected track.

NOTE

You can cancel changes made

to the initial settings by select-

ing a different track after Step 2,

then exiting Record mode dur-

ing Step 3 without pressing the

[REC] button. (Changes made

to the data shared by two tracks

are also canceled.)

YDP-223 Playing Back Recorded Songs

ENGLISH

Playing Back Recorded Songs

You can play back songs recorded using the Record function

(pages 28–31). You can also play the keyboard along with the play-

back.

Playing Back a Song

1. Start playback.

Press the SONG [START/STOP] button.

The current measure number appears on the display during playback.

•You can play the keyboard while the YDP-223 is playing back a song. You can

also play the notes in a voice different from the playback voice by selecting a

voice from the panel.

Adjust the volume

Use the [MASTER VOLUME] control to adjust the volume.

Adjust the tempo

You can use the [TEMPO/FUNCTION# ▼, ▲] buttons to adjust the playback

tempo as required before or during playback. The default tempo (the song’s

original tempo) is set when you press the [▼] and [▲] buttons simultaneously.

2. Stop playback.

When playback is complete, the YDP-223 automatically stops and locates the

top of the song. To stop playback in the middle of a song, press the SONG

[START/STOP]

button.

NOTE

Song data is not transmitted via

the MIDI connectors.

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

NOTE

When the unit is in Demo Song

or Preset Song mode, you can-

not play back recorded songs.

NOTE

The track indicators will not light

up green automatically when the

power is turned on, even if the

user song recorder contains

data. Make sure that you press

the track buttons before you start

playback.

NOTE

Playback cannot be started when

the recorder contains no data.

TIP

You can also enjoy playing

duets with yourself by record-

ing one part of a duet or a song

for two pianos, then playing the

other part while the recorded

part plays back.

TIP

If the metronome is being used

during playback, the metro-

nome will automatically stop

when playback is stopped.

TIP

If the REVERB type is changed

via the panel controls during

playback, both the playback and

keyboard reverb effects will be

changed.

TIP

If the EFFECT type is changed

via the panel controls during

playback, the playback effect may

be switched off in some cases.

Procedure

YDP-223 Playing Back Recorded Songs

ENGLISH

Useful Playback Functions

Turning track playback on and off

When you select a song on the YDP-223, the indicators for tracks that contain

data (one of

[TRACK1] [TRACK2] or both) are lit in green. While the YDP-223 is play-

ing or stopped, pressing these track buttons turns off the indicators, and the data on

those tracks is not played. Pressing the track buttons toggles track playback on and off.

Starting playback automatically when you start playing the keyboard

(Synchro Start)

You can start playback as soon as you start playing the keyboard. This is called the

“Synchro Start” function.

To engage the Synchro Start function, press the SONG [START/STOP] button while

holding a track button that is ON.

The right-most dot on the display will ﬂash at the current

tempo.

(Repeat the previous operation to disengage the Synchro

Start function.)

Playback will then start as soon as you begin playing on the keyboard.

This function is useful when you wish to match the timing of the beginning of the play-

back sound and the start of your own performance.

Assigning the START/STOP function to the left pedal

The left pedal can also be assigned to song start/stop operation via the “Pedal Start/

Stop” (page 40).

This is convenient for starting playback of the recorded part anytime after you have

started playing.

TIP

Tracks can be turned on or off

before or during playback.

If both tracks are turned off,

playback will not start (or the

playback will stop).

TIP

You can adjust the volume of a

part of a song from “50 Greats

for the Piano” for which play-

back is turned off

(pages 18, 40).

During recorder playback, the

volume of a track that is turned

off will always be “0.”

NOTE

If you press the SONG [START/

STOP] button while holding

down a track button that is OFF,

track playback is turned on and

the Synchro Start function is

placed on stand-by.

TERMINOLOGY

Synchro:

Synchronous; occurring at the

same time

Flash

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

Detailed Settings – [FUNCTION]

You can set various parameters to make the best use of YDP-223 functions, such as ﬁne tuning the pitch, selecting a voice

for the metronome, repeating playback, etc.

The following parameters are available.

The YDP-223 has eight main functions.

Some of these main functions consist of a set of sub-modes.

Parameter List

Function Sub-Mode Function Number Reference page

Fine tuning of the pitch

—F137

Selecting a scale

Scale F2.1 38

Base Note F2.2 38

Dual mode functions

Dual Balance F3.1 39

Dual Detune F3.2 39

Voice 1 Octave Shift F3.3 39

Voice 2 Octave Shift F3.4 39

Voice 1 Effect Depth F3.5 39

Voice 2 Effect Depth F3.6 39

Reset F3.7 39

Other Functions

Left Pedal Mode F4.1 40

Soft Pedal Effect Depth F4.2 40

Metronome volume

—F540

Preset Song Part Cancel

Volume

— F6 40

MIDI Functions

MIDI Transmit Channel Selection F7.1 41

MIDI Receive Channel Selection F7.2 41

Local Control ON/OFF F7.3 41

Program Change ON/OFF F7.4 42

Control Change ON/OFF F7.5 42

MIDI Transmit Transpose F7.6 42

Panel/Status Transmit F7.7 42

Bulk Data Dump F7.8 43

Backup Functions

Voice F8.1 44

MIDI F8.2 44

Tuning F8.3 44

Others F8.4 44

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

Basic Procedure in Function Mode

Follow the steps below to use the functions.

(If you become lost while using a function, return to this page and read the basic procedure.)

1. Engage Function mode.

Press the [TEMPO/FUNCTION#] button so that its [FUNCTION#] indicator

lights.

will appear on the display. (The indication of “ ” varies depending on

the status of the unit and usage.)

2. Select a function.

Use the [TEMPO/FUNCTION# ▼, ▲] buttons to select the desired function

from F1–F8.

3. Use the [–/NO] [+/YES] buttons.

If the function does not include sub-modes, start setting the parameters.

If the function includes sub-modes, press the [+/YES] button once to enter the

respective sub-mode.

4. Operate the desired function using the following

two buttons.

1 [TEMPO/FUNCTION# ▼, ▲]

Selects the desired function/sub-mode.

2 [–/NO] or [+/YES]

After you select the desired function or sub-mode, set the ON/OFF, select

the type, or change the value, accordingly.

Depending on the setting, the default setting (which is used when you

ﬁrst turn on the power to the YDP-223) is recalled by pressing the [–/NO]

and [+/YES] buttons simultaneously.

124 45

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

SONG

GRAND

PIANO 1

CHURCH

ORGAN1

CHURCH

ORGAN2

E.PIANO

HARPSI-

CHORD1

HARPSI-

CHORD2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

JAZZ

ORGAN

STRINGS

REVERB EFFECT TOUCH TRANSPOSE

VOIC E

Procedure

NOTE

Functions cannot be selected

during Demo/Preset Song

mode or when the user song

recorder is in operation.

NOTE

To cancel the function in Step 2,

3, or 4, press the [TEMPO/

FUNCTION# ▼, ▲] button any

time to exit Function mode.

TEMPO

FUNCTION

TEMPO

FUNCTION

TIP

After you select the function, the

current setting will be displayed

when the [–/NO] or [+/YES] but-

ton is pressed for the ﬁrst time.

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

Operation Example 1 (F1. Fine tuning of the pitch)

Operation Example 2 (F3.1 “Dual Balance”)

5. Do the following when you ﬁnish using the func-

tion.

To exit Function mode, press the [TEMPO/FUNCTION#] button so that its

[TEMPO] indicator lights.

Change the value.

Engage Function mode.

Select a desired function.

TEMPO

FUNCTION

TEMPO

FUNCTION

TEMPO

FUNCTION

TEMPO

FUNCTION

–

NO +

YES

LCD indication

Engage the respective

sub-mode.

Engage function mode.

Select a desired function.

Select a desired sub-mode.

Change the value.

TEMPO

FUNCTION

TEMPO

FUNCTION

TEMPO

FUNCTION

TEMPO

FUNCTION

TEMPO

FUNCTION

TEMPO

FUNCTION

–

NO +

YES

LCD indication

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

About Each Function

You can ﬁne tune the pitch of the entire instru-

ment. This function is useful when you play

the YDP-223 along with other instruments or

CD music.

1. Engage Function mode and select .

2. Use the [–/NO] and [+/YES] buttons to lower

or raise the pitch of the A3 key in approxi-

mately 0.2 Hz increments.

..... .....

Te nths of a hertz are indicated on the LED display by

the appearance and position of one or two dots, as in

the following example:

•Refer to “Part Names” on page 14 for information on

the key and key name assignment.

(During the procedure described above, the display indi-

cates a value in Hz < … >. After the proce-

dure, the display returns to the previous indication.)

(During the procedure described above, the display indi-

cates a value in Hz < … >. After the proce-

dure, the display returns to the previous indication.)

F1. Fine Tuning of the Pitch

Display Value

440.0

Setting range:

440.2

427.0–453.0 (Hz)

440.4

Normal setting:

440.6

440.0 (Hz)

440.8

TERMINOLOGY

Hz (Hertz):

This unit of measurement refers to the frequency of a sound

and represents the number of times a sound wave vibrates in

a second.

TIP

You can also use the keyboard to set the pitch (in any

mode other than Function mode).

To tune up (in about 0.2Hz steps): Hold the A-1 and B-1

keys (two white keys at the left end) simultaneously and

press any key between C3 and B3.

To tune down (in about 0.2Hz steps): Hold the A-1 and A



-1

keys (a white and a black key at the left end) simultaneously

and press any key between C3 and B3.

To restore standard pitch: Hold the A-1, A



-1 and B-1 (two

white keys and one black key at the left end) simultaneously

and press any key between C3 and B3.

TIP

You can also tune in about 1Hz steps (in any mode other

than Function mode).

To tune down or up, respectively, in approximately 1 Hz

increments: Hold the A-1 and A



-1 keys (a white and a black

key at the left end) or A-1 and B-1 keys (two white keys at the

left end) simultaneously and press the [–/NO] or [+/YES] but-

ton.

To restore standard pitch: Hold the A-1 and A



-1 keys (a

white and a black key at the left end) or A-1 and B-1 keys

(two white keys at the left end) simultaneously and press the

[–/NO] [+/YES] buttons simultaneously.

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

You can select various scales.

Equal Temperament is the most common con-

temporary piano tuning scale. However, his-

tory has known numerous other scales, many

of which serve as the basis for certain genres of

music. You can experience these tunings with

the YDP-223.

Equal

One octave is divided into twelve equal intervals. Cur-

rently the most popular piano tuning scale.

PureMajor/PureMinor

Based on natural overtones, three major chords using

these scales produce a beautiful, pure sound. They are

sometimes used for chorus parts.

Pythagorean

This scale, designed by Pythagoras, a Greek philosopher,

is based on the interval of a perfect 5th.

The 3rd produces swells, but the 4th and 5th are beauti-

ful and suitable for some leads.

MeanTone

This scale is an improvement of the Pythagorean in that

the swell of the 3rd has been eliminated. The scale

became popular during the late 16th century through the

late 18th century, and was used by Handel.

WerckMeister/KirnBerger

These scales combine Mean Tone and Pythagorean in

different ways. With these scales, modulation changes the

impression and feel of the songs. They were often used in

the era of Bach and Beethoven. They are often used today

to reproduce the music of that era on harpsichords.

1. Engage Function mode and select .

2. Press the [+/YES] button to engage the scale

function’s sub-mode, then use the [TEMPO/

FUNCTION# ▼, ▲] buttons to select the

desired sub-mode.

Press the [–/NO] and [+/YES] buttons to select

the number of the desired tuning.

Sub-mode

F2.1: Scale

Setting range: 1: Equal Temperament

2: Pure Major

3: Pure Minor

4: Pythagorean

5: Mean Tone

6: Werckmeister

7: Kirnberger

Normal setting: 1: Equal Temperament

F2.2: Base Note

If you select a scale other than Equal Temperament, you

need to specify the root. (You can specify the root note

with Equal Temperament selected, but it is not effective.

The base note setting is effective for tunings other than

the Equal Temperament tuning.)

Setting range:

Normal setting:

•Root indication example

F2. Selecting a Scale



) (G)

followed by

a high bar if sharp



)

followed by

a low bar if flat

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

You can set various parameters for Dual mode

to optimize the settings for the songs you play,

such as adjusting the volume balance between

two voices.

Dual mode function settings are set individu-

ally for each voice combination.

1. Select the voices in Dual mode and engage

Function mode and select .

2. Press the [+/YES] button to engage the Dual

mode function’s sub-mode, then use the

[TEMPO/FUNCTION# ▼, ▲] buttons to select

the desired sub-mode. Press the [–/NO] [+/

YES] button to assign values.

Sub-mode

F3.1: Dual Balance

Setting range: 0 – 20 (A setting of “10” produces an

equal balance between the two Dual

mode voices. Settings below “10”

increase the volume of Voice 2 in

relation to Voice 1, and settings

above “10” increase the volume of

Vo ice 1 in relation to Voice 2.)

Normal setting: Different for each voice combina-

tion.

You can set one voice as the main voice, and another

voice as a softer, mixed voice.

F3.2: Dual Detune

Setting range: -10 – 0 – 10 (With positive values,

the pitch of Voice 1 is raised and the

pitch of Voice 2 is lowered. With neg-

ative values, the pitch of Voice 1 is

lowered and the pitch of Voice 2 is

raised.)

Normal setting: Different for each voice combina-

tion.

Detune Voice 1 and Voice 2 for Dual mode to create a

thicker sound.

F3.3: Voice 1 Octave Shift

F3.4: Voice 2 Octave Shift

Setting range: –1, 0, 1

Normal setting: Different for each voice combina-

tion.

You can shift the pitch up and down in octave steps for

Vo ice 1 and Voice 2 independently. Depending on which

voices you combine in Dual mode, the combination may

sound better if one of the voices is shifted up or down an

octave.

F3.5: Voice 1 Effect Depth

F3.6: Voice 2 Effect Depth

Setting range: 0 – 20

Normal setting: Different for each voice combina-

tion.

These functions make it possible to individually set the

depth of the effect for Voices 1 and 2 for Dual mode.

(The effect depth settings cannot be changed unless the

[EFFECT] is ON. Function mode must be exited before

the [EFFECT] can be turned ON.)

•“Vo ice 1” and “Voice 2” are explained on page 26.

F3.7: Reset

This function resets all Dual mode functions to their

default values. Press the [+/YES] button to reset the val-

ues.

F3. Dual Mode Functions

NOTE

If Dual mode is not engaged, will appear instead of

and you will be unable to select Dual mode functions.

You can switch from Function mode to Dual mode.

TIP

The available setting range is wider in the lower range (± 60

cents for A-1), and narrower in the higher range (± 5 cents for

C7). (100 cents equal one semitone.)

TIP

SHORTCUT:

You can jump directly to the Dual mode functions by

pressing the [TEMPO/FUNCTION#] button while holding the

two Dual mode voice buttons.

To exit Function mode, you still need to press the [TEMPO/

FUNCTION#] button so that the TEMPO indicator lights up.

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

This function conveniently lets you set opera-

tion of the left pedal to one of the modes

listed below.

1. Engage Function mode and select .

2. Press the [+/YES] button to engage the other

functions’ sub-mode, then use the [TEMPO/

FUNCTION# ▼, ▲] buttons to select the

desired sub-mode.

Press the [–/NO] or [+/YES] button to select

the desired pedal function or assign the val-

ues.

Sub-mode

Left Pedal Mode

Setting range:

1. Soft Pedal

The soft pedal reduces the volume and slightly

changes the timbre of notes played while the pedal is

pressed. The soft pedal will not affect notes that are

already playing.

2. Song Start/Stop

This mode allows you to start or stop song playback.

In this mode, the Left Pedal functions in the same

manner as the SONG [START/STOP] button on the

panel.

Normal setting: 1(Soft Pedal)

Soft Pedal Effect Depth

Setting range: 1 – 15

Normal setting: 3

This function sets the depth of the soft pedal effect.

You can change the volume of the metronome

sound.

Use this function to adjust the metronome vol-

ume.

1. Engage Function mode and select .

2. Use the [–/NO] and [+/YES] buttons to set the

metronome volume as required.

Setting range: 1 – 20

Normal setting: 10

This function sets the volume at which a “can-

celed” part is played during preset song play-

back. Adjust the part volume to a comfortable

level and use the “canceled” part as a guide

with which to play along.

1. Engage Function mode and select .

2. Use the [–/NO] and [+/YES] buttons to set the

volume as required.

Setting range: 0 – 20

Normal setting: 5

F4. Other Functions F5 Metronome Volume

TIP

SHORTCUT:

You can jump directly to the metronome functions by

pressing the [TEMPO/FUNCTION#] button while holding the

METRONOME [START/STOP] button.

To exit Function mode, you still need to press the [TEMPO/

FUNCTION#] button so that the TEMPO indicator lights up.

F6. Preset Song Part Cancel Volume

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

You can make detailed adjustments to MIDI

settings.

For more information about MIDI, see the

“About MIDI” section (page 45).

1. Engage Function mode and select .

2. Press the [+/YES] button to engage the MIDI

function’s sub-mode, then use the [TEMPO/

FUNCTION# ▼, ▲] buttons to select the

desired sub-mode.

Press the [–/NO] or [+/YES] button to set a

selected parameter.

Sub-mode

MIDI Transmit Channel Selection

In any MIDI control setup, the MIDI channels of the

transmitting and receiving equipment must be matched

for proper data transfer.

This parameter enables you to specify the channel on

which the YDP-223 transmits MIDI data.

Setting range: 1 – 16, OFF (not transmitted)

Normal setting: 1

MIDI Receive Channel Selection

In any MIDI control setup, the MIDI channels of the

transmitting and receiving equipment must be matched

for proper data transfer. This parameter enables you to

specify the channel on which the YDP-223 receives MIDI

data.

Setting range: ALL, 1&2, 1 – 16

Normal setting: ALL

Local Control ON/OFF

“Local Control” refers to the fact that, normally, the

YDP-223 keyboard controls its internal tone generator,

allowing the internal voices to be played directly from the

keyboard. This situation is “Local Control On,” since the

internal tone generator is controlled locally by its own

keyboard.

Local control can be turned OFF, however, so that the

YDP-223 keyboard does not play the internal voices, but

the appropriate MIDI information is still transmitted via

the MIDI OUT connector when notes are played on the

keyboard. At the same time, the internal tone generator

responds to MIDI information received via the MIDI IN

connector.

Setting range: ON/OFF

Normal setting: ON

F7. MIDI Functions

TIP

The HOST SELECT switch on the bottom surface must be

set to “MIDI” to enable the MIDI connectors. When you use

the TO HOST connector, set the HOST SELECT switch to

the appropriate position for the type of computer you are

using (pages 45–51). In this situation, all MIDI settings

described below will affect the MIDI signal in and out of the

TO HOST connector.

NOTE

In Dual mode, Voice 1 data is transmitted on its speciﬁed

channel. Voice 2 data is transmitted on the next greater chan-

nel number relative to the speciﬁed channel. No data is trans-

mitted if the transmit channel is set to “OFF”.

NOTE

Demo/preset song data and recorder playback data are not

transmitted via MIDI.

TIP

ALL:

A “Multi-timbre” Receive mode is available. It allows simulta-

neous reception of different parts on all 16 MIDI channels,

enabling the YDP-223 to play multi-channel song data

received from a music computer or sequencer.

1&2:

A “1&2” Receive mode is available. It allows simultaneous

reception on channels 1 and 2 only, enabling the YDP-223 to

play 1 and 2 channel song data received from a music com-

puter or sequencer.

TIP

Program change and other like channel messages received

will not affect the YDP-223’s panel settings or the notes you

play on the keyboard.

NOTE

No MIDI reception occurs when Demo/Preset Song mode is

engaged.

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

Program Change ON/OFF

Normally the YDP-223 will respond to MIDI program

change numbers received from an external keyboard or

other MIDI device, causing the correspondingly-num-

bered voice to be selected on the corresponding channel

(the keyboard voice does not change). The YDP-223 will

normally also send a MIDI program change number

whenever one of its voices is selected, causing the corre-

spondingly-numbered voice or program to be selected

on the external MIDI device if the device is set up to

receive and respond to MIDI program change numbers.

This function makes it possible to cancel program

change number reception and transmission so that

voices can be selected on the YDP-223 without affecting

the external MIDI device.

Setting range: ON/OFF

Normal setting: ON

Control Change ON/OFF

Normally the YDP-223 will respond to MIDI control

change data received from an external MIDI device or

keyboard, causing the voice on the corresponding chan-

nel to be affected by pedal and other “control” settings

received from the controlling device (the keyboard voice

is not affected).

The YDP-223 also transmits MIDI control change infor-

mation when the pedal or other appropriate controls are

operated.

This function makes it possible to cancel control change

data reception and transmission so that, for example, the

YDP-223’s pedal and other controls can be operated

without affecting an external MIDI device.

Setting range: ON/OFF

Normal setting: ON

MIDI Transmit Transpose

This function allows the MIDI note data transmitted by

the YDP-223 to be transposed up or down in semitone

increments by up to plus or minus 12 semitones. The

pitch of the YDP-223 itself is not affected.

Setting range: -12 – 0 – 12 (in semitones)

Normal setting: 0

Panel/Status Transmit

This function causes all the current YDP-223 panel set-

tings (selected voice, etc.) to be transmitted via the MIDI

OUT terminal. This is particularly useful if you will be

recording performances to a MIDI sequence recorder,

such as the Yamaha MIDI Data Filer MDF3, which will

be used to control the YDP-223 on playback. By trans-

mitting the YDP-223 panel settings and recording them

on the MIDI sequence recorder prior to the actual per-

formance data, the YDP-223 will be automatically

restored to the same settings when the performance is

played back.

Procedure

1. Set up the panel controls as desired.

2. Connect the YDP-223 to a sequencer via MIDI, and

set up the sequencer so it can receive the setup data.

3. Engage Function mode and select .

4. Press the [+/YES] button to transmit the panel/status

data.

will appear on the LED display when the data has

been successfully transmitted.

TIP

For information on program change numbers for each of the

YDP-223’s voices, refer to page 61 in the MIDI Data Format

section.

TIP

For information on control changes that can be used with the

YDP-223, refer to the MIDI Data Format on page 61.

TERMINOLOGY

Setup Data:

Data that contains a set of panel settings for the YDP-223.

TIP

See page 62 for a list of the “Panel Data Contents” transmit-

ted by this function.

TIP

Receiving the transmitted data:

1. Connect the YDP-223 via MIDI to the device to which the

setup data was transmitted previously.

2. Start sending the setup data from the device.

The YDP-223 automatically receives the setup data, which

will be reﬂected in the panel settings.

(For the data to be accepted, the YDP-223 that receives the

setup data should be the same model as the one that trans-

mitted the setup data to the sequencer.)

TIP

For more information on transmitting and receiving setup

data via MIDI, refer to the owner’s manual for the connected

MIDI device.

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

Bulk Data Dump

You can save current song data on the YDP-223 as MIDI

bulk data by transferring it to a connected MIDI data

ﬁler (such as an MDF3) or a sequencer. To play back the

saved song data, send the bulk data back from the storage

device to the YDP-223 and follow the usual playback

procedure.

Procedure

1. Record your performance on the YDP-223.

2. Connect the YDP-223 to MDF3, a MIDI data ﬁler via

MIDI, and set up the MDF3 so it will receive bulk

data.

3. Engage Function mode and select .

4. Press the [+/YES] button to begin bulk transmission.

will appear on the LED display when the data has

been successfully transmitted.

TERMINOLOGY

bulk data:

A complete set or extended sequence of data

NOTE

No MIDI note/panel data transmission or data reception

occurs during a bulk data dump transmit operation.

TIP

Receiving (returning) the transmitted data:

1. Connect the YDP-223 via MIDI to the device to which the

data was previously transmitted.

2. Start sending the data from the device.

The YDP-223 automatically receives the data from the unit.

(At this time, any data previously stored in the YDP-223 will

be erased.)

Then, follow the usual playback procedure.

(For the data to be accepted, the YDP-223 that receives the

data should be the same model as the one from which the

data was once transmitted to the MIDI data ﬁler.)

NOTE

The reload operation cannot be executed when Demo/Preset

Song mode or the user song recorder is in operation, or

when Function mode is engaged.

TIP

For more information on transmitting and receiving bulk data

via MIDI, refer to the owner’s manual for the connected MIDI

device.

YDP-223 Detailed Settings – [FUNCTION]

ENGLISH

However, the backup settings themselves, and the con-

tents of the user song recorder memory, are always

backed up.

CAUTION

Even if the backup function is turned on via one of the

functions described below, the data will be retained in

memory for only about one week if the power is not

turned on during this time. If the backup period is

exceeded, all settings will be reset to their default values.

If you want to retain the backup settings for longer peri-

ods, be sure to turn the power on for a few minutes at

least once a week.

You can turn the backup function on or off for

each function group (each of the following

sub-mode functions).

1. Engage Function mode and select .

2. Press the [+/YES] button to engage the

backup function’s sub-mode, then use the

[TEMPO/FUNCTION# ▼, ▲] buttons to select

the desired sub-mode.

Press the [–/NO] or [+/YES] button to turn the

backup function on or off.

Sub-mode

Voice

MIDI

Tuning

Others

Setting range: ON/OFF

Normal setting: OFF (all groups)

Description of sub-modes

F8.1: Voice

•Voice (Keyboard and Dual)

•Dual (ON/OFF, Voice, and Dual Functions for each

voice combination)

•Reverb (ON/OFF, Type, and Depth for each voice)

• Effect (ON/OFF, Type, and Depth for each voice)

•Touch Sensitivity (including the FIXED volume)

•Metronome (Beat, Volume < settings>)

•Preset Song Part Cancel Volume ( settings)

F8.2: MIDI

The MIDI functions ( settings)

(expect for the )

F8.3: Tuning

•Transpose

•Tuning ( settings)

• Scale (including base note) ( settings)

F8.4: Others

Other functions ( settings)

Factory Preset Recall

All Dual mode, reverb, effect, touch sensitivity, tuning

settings, and the settings affected by the Backup Func-

tions can be restored to their original factory preset val-

ues by holding the C7 key (right-most key on the

keyboard) while turning the [POWER] button ON. This

also erases all user song recorder data, and sets all backup

on/off settings (F8) to “OFF”. (The factory setting list is

found on page 60.)

F8. Backup Functions

TERMINOLOGY

Backup:

You can back up some settings, such as voice selection and

reverb type, so that they will not be lost when you turn off the

power to the YDP-223.

If the backup function is turned on, the settings at power off

are effective. If the backup function is turned off, the settings

in memory are erased when you turn off the power. In this

case, when you turn on the power to the unit, the default set-

tings (the initial settings) will be used. (The factory setting

default list is found on page 60.)

YDP-223 About MIDI

ENGLISH

About MIDI

MIDI (Musical Instrument Digital Interface) is a standard format for

data transmission/reception. It enables the transfer of performance

data and commands between MIDI devices and personal computers.

Using MIDI, you can control a connected MIDI device from the YDP-

223, or control the YDP-223 from a connected MIDI device or com-

puter.

MIDI connectors

MIDI [IN]: Receives MIDI data.

MIDI [OUT]: Tr ansmits MIDI data.

MIDI [THRU]: Tr ansmits data received at the MIDI [IN] connector as it is.

MIDI cables

Prepare dedicated MIDI cables.

[TO HOST] connector

Use this connector to connect the YDP-223 to a computer.

TIP

MIDI performance data and

commands are transferred in

the form of numeric values.

TIP

Since MIDI data that can be

transmitted or received varies

depending on the type of MIDI

device, check the “MIDI Imple-

mentation Chart” to ﬁnd out

what MIDI data and commands

your devices can transmit or

receive. The YDP-223’s MIDI

Implementation Chart appears

on page 65.

HOST SELECT

MIDI

THRU

MIDIMac

PC-2PC-1

OUT IN

NOTE

When you are using the MIDI

connectors, set the [HOST

SELECT] switch to “MIDI”

(page 50).

NOTE

When you are using the [TO

HOST] connector, set the

[HOST SELECT] switch,

according to the type of com-

puter you are using (page 50).

TIP

You can also obtain detailed

information about MIDI from

various music books and other

publications.

TO HOST HOST SELECT

MIDI

PC-2

Mac

PC-1

YDP-223 Connections

ENGLISH

Connections

Connectors

CAUTION

Before connecting the YDP-223 to other electronic components, turn off the power to all the components. Before turning

the power on or off to all components, set all volume levels to minimum (0). Otherwise, electrical shock or damage to the

components may result.

1 AUX OUT [R] [L] Pin jacks (LEVEL FIXED), [R] [L/L+R] Phone jacks

You can connect these jacks to a stereo system to amplify the YDP-223 or to a cas-

sette tape recorder to record your performance. Refer to the diagram below and use

audio cables to make the connections.

CAUTION

Do not route the output from the AUX OUT jacks to the AUX IN jacks. That is, when

you connect an external audio device to the AUX OUT jacks, do not connect the audio

device to the YDP-223’s AUX IN jacks. If you make this connection, the signal input at

the AUX IN jacks will be output from AUX OUT. This creates an audio loop, causing

audio oscillation and abnormal playback, and leading to malfunction of both pieces of

equipment.

CAUTION

When the YDP-223’s AUX OUT jacks are connected to an external audio system, ﬁrst

turn on the power to the YDP-223, then to the external audio system. Reverse this

order when you turn the power off.

AUX OUT AUX IN

L+R

LEVEL FIXED

R L

L+RRLR

PEDAL

TO HOST HOST SELECT

MIDI

THRU

MIDIMac

PC-2PC-1

OUT IN

NOTE

Use audio cables and adaptor

plugs with no resistance.

NOTE

The YDP-223’s [MASTER VOL-

UME] and [BRILLIANCE] slider

setting does not affect the sig-

nal output from the AUX OUT

(LEVEL FIXED) jacks.

YDP-223

Stereo

RCA

pin plug

To powered speakers

RCA

pin plug

AUX IN

When these are connected (with stan-

dard phone plugs), you can use the

[MASTER VOLUME] control to adjust

the volume of the sound output to the

external device.

AUX OUT

L+RRL

LEVEL FIXED

When these are connected (with RCA pin

plug; LEVEL FIXED), the sound is output to

the external device at a fixed level, regardless

of the [MASTER VOLUME] control setting.

phone

plug

(standard)

audio cable

YDP-223 Connections

ENGLISH

AUX IN [R], [L/L+R] jacks

The stereo outputs from another instrument can be connected to these jacks,

allowing the sound of an external instrument to be reproduced via the YDP-223’s

speakers. Refer to the diagram below and use audio cables to make the connec-

tions.

CAUTION

When the YDP-223’s AUX IN jacks are connected to an external device, ﬁrst turn on the

power to the external device, then to the YDP-223. Reverse this order when you turn

the power off.

3 TO HOST jack

This jack allows direct connection to a personal computer. (Refer to “Connecting a

personal computer” on page 48 for more information.)

4 HOST SELECT switch

This switch should be set according to the type of connected MIDI device or per-

sonal computer. (Refer to “Connecting a personal computer” on page 48 for more

information.)

5 MIDI [IN], [OUT], [THRU] connectors

Use MIDI cables to connect external MIDI devices to these connectors.

Make sure you set the HOST SELECT switch to MIDI when you use these connec-

tors.

(Refer to “About MIDI” on page 45 for more information.)

6 PEDAL jack

Connect the pedal cord from the pedal box. (Refer to “Keyboard Stand Assembly”

on pages 53-55.)

NOTE

The YDP-223’s [MASTER VOL-

UME] and [BRILLIANCE] slider

settings affect the input signal

from the AUX IN jacks, but the

[REVERB] and [EFFECT] set-

tings do not.

NOTE

If you connect the YDP-223 to a

monaural device, use only the

AUX IN [L/L+R] jack or AUX

OUT [L/L+R] jack.

AUX IN

audio cable

Tone Generator

AUX OUT

YDP-223

phone plug

(standard)

phone plug

(standard)

AUX IN

L+RR

YDP-223 Connections

ENGLISH

Connecting a Personal Computer

You can enjoy computer music data on the YDP-223 by connecting a computer to the TO HOST (or

MIDI) jack.

There are three methods by which to connect the YDP-223 to a personal computer:

1. Connect the serial port on the computer to the YDP-223’s TO HOST jack (page 49).

2. Use a MIDI interface and the YDP-223’s MIDI connectors (page 50).

3. Use the USB port on the computer and the UX16, UX96, or UX256, a USB interface (page 51).

For more information, refer to the speciﬁed pages.

NOTE

When the YDP-223 is used as a tone module, performance data with voices that are not found on the YDP-223 will not

be played correctly.

“The Clavinova-Computer Connection,” is a supplementary guidebook that describes, for beginners, what you

can do with your YDP-223 and a personal computer and how to set up a YDP-223-Computer system (although the

guidebook only mentions the Clavinova, it applies equally to the YDP-223 digital piano). The document is available

as a PDF file (in English) at the following Internet address:

Clavinova Web site (English only):

http://www.yamahaclavinova.com/

Yamaha Manual Library:

http://www2.yamaha.co.jp/manual/english/

NOTE

When connecting the YDP-223 to a personal computer, ﬁrst turn off the power to both the YDP-223 and the computer

before you connect any cables or set the HOST SELECT switch. After making the connections and switch settings, turn

on the power to the computer ﬁrst, then to the YDP-223.

NOTE

If you do not use the [TO HOST] jack of the YDP-223, make sure you disconnect the cable from the jack. If the cable is

left connected, the YDP-223 may not function properly.

NOTE

will appear in the display if the host computer is not turned on, the connecting cable is not properly connected,

the HOST SELECT switch is not in the proper position, or the MIDI driver or MIDI application is not active. In this situa-

tion, turn the power off to both the YDP-223 and the computer, and check the cable connection and the position of the

HOST SELECT switch. Once the connection and HOST SELECT switch position is veriﬁed, turn the power of the com-

puter on ﬁrst, then the YDP-223, and check whether the MIDI driver and MIDI application function properly.

NOTE

When the [HOST SELECT] switch is set to “PC-1,” PC-2,” or “Mac,” you can use the [TO HOST] jack, but the MIDI con-

nectors are disabled since no data transfer occurs via the MIDI connectors. On the other hand, when the [HOST

SELECT] switch is set to “MIDI,” you can use the MIDI connectors, but not the [TO HOST] jack since no data is trans-

ferred via the [TO HOST] jack.

YDP-223 Connections

ENGLISH

1. Connecting the serial port on the computer to the YDP-223’s TO HOST jack

Connect the computer’s serial port (RS-232C or RS-422) to the YDP-223’s TO HOST jack.

With this connection, the YDP-223 functions as a MIDI interface. Therefore, you do not need a special MIDI interface.

Connection

Use a special serial cable (page 49) to connect the computer’s serial port (RS-232C or RS-422) to the YDP-223’s TO HOST

jack.

Type of serial cables and connection pin assignments

Depending on the type of computer you connect, use one of the following serial cables.

Note for Windows users

(regarding the MIDI driver)

To transfer data via the computer’s

serial port and the YDP-223’s TO

HOST jack, you need to install a

speciﬁc MIDI driver (the Yamaha

CBX driver for Windows). You can

download this driver from the fol-

lowing XG Library on the Yamaha

web site:

http://www.yamaha-xg.com

YDP-223

TO HOST

TO HOST HOST SELECT

MIDI

PC-2

Mac

PC-1

Windows Windows Macintosh

modem portRS-232C (D-sub 9-pin) RS-232C (D-sub 25-pin)

Windows (with a serial port of D-sub 9-pin)

8-pin mini DIN plug ➝ D-sub 9-pin plug

(Yamaha CCJ-PC2 or equivalent)

Macintosh

System peripheral plug ➝ 8-pin plug

(Yamaha CCJ-MAC or equivalent)

Windows (with a serial port of D-sub 25-pin)

8-pin mini DIN plug ➝ D-sub 25-pin plug

(Yamaha CCJ-PC1NF or equivalent)

Pin assignment

The following diagram shows the pin assignments for each cable.

8 (CTS)

7 (RTS)

2 (RxD)

5 (GND)

3 (TxD)

mini DIN

8-pin

D-sub

9-pin

2 (HSK i)

1 (HSK O)

5 (RxD-)

4 (GND)

3 (TxD-)

8 (RxD+)

7 (GP-)

6 (TxD+)

mini DIN

8-pin

mini DIN

8-pin

5 (CTS)

4 (RTS)

3 (RxD)

7 (GND)

2 (TxD)

mini DIN

8-pin

D-sub

25-pin

mini DIN 8-pin

D-sub 25-pin

Pin numbers (view from front)

D-sub 9-pin

YDP-223 Connections

ENGLISH

YDP-223 HOST SELECT switch setting

Set the YDP-223 HOST SELECT switch properly according to the type of connected computer.

• Macintosh: “Mac” (data transfer rate: 31,250bps, 1MHz clock)

• Windows: “PC-2” (data transfer rate: 38,400bps)

2. Using a MIDI interface and the YDP-223’s MIDI connectors

Connection

Use a MIDI interface device to connect a computer to the YDP-223 using special MIDI cables.

YDP-223 HOST SELECT switch setting

Set the YDP-223 HOST SELECT switch to “MIDI.”

TIP

If your system does not work properly with the connections and settings listed above, your software may require differ-

ent settings. Check your software operation manual and set the HOST SELECT switch to the proper data transfer rate.

(Data transfer rate of “PC-1” is 31,250bps.)

MIDI OUT

MIDI

OUT

MIDI

OUT

MIDI

Windows Macintosh

YDP-223

MIDI interface

HOST SELECT

MIDI

THRU

MIDIMac

PC-2PC-1

OUT IN

YDP-223 Connections

ENGLISH

3. Connecting the computer’s USB port to the YDP-223 via a USB interface, such as

the UX16, UX96, or UX256

Connect the computer’s USB port to the USB interface (such as the UX16, UX96, or UX256) using a USB cable. Install

the driver (that came with the USB interface) on the computer, and connect the USB interface to the YDP-223 using a

serial cable or MIDI cables.

For more information, refer to the instruction manual for the USB interface.

An example of connecting the USB interface to the YDP-223 using a serial cable

An example of connecting the USB interface to the YDP-223 using MIDI cables

TO HOST HOST SELECT

PC-1

Mac

USB interface

USB cable

computer

Standard Machintosh 8-pin system peripheral cable

C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4

C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7

B-1A-1

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

GRAND

PIANO 1

CHURCH

ORGAN 1

E.PIANO

HARPSI-

CHORD 1

HARPSI-

CHORD 2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

CHURCH

ORGAN 2

STRINGS

JAZZ

ORGAN

VOICE

REVERB EFFECT TOUCH TRANSPOSE

SONG

POWER

YDP-223

USB cable

MIDI cables

USB interface

computer

C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4

C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7

B-1A-1

MASTER VOLUME

BRILLIANCE

DEMO METRONOME

TEMPO

FUNCTION

TEMPO

OTHER VALUE

MELLOW BRIGHT

START

STOP

TEMPO

FUNCTION

MIN MAX

–

NO +

YES PRESET

TRACK

START

STOP

REC

GRAND

PIANO 1

CHURCH

ORGAN 1

E.PIANO

HARPSI-

CHORD 1

HARPSI-

CHORD 2

VIBRA-

PHONE

CHOIR GUITAR

ROOM

HALL 1

HALL 2

STAGE

CHORUS

PHASER

TREMOLO

DELAY

HARD

MEDIUM

SOFT

GRAND

PIANO 2

CHURCH

ORGAN 2

STRINGS

JAZZ

ORGAN

VOICE

REVERB EFFECT TOUCH TRANSPOSE

SONG

POWER

HOST SELECT

MIDI

THRU

MIDIMac

PC-2PC-1

OUT IN

YDP-223

YDP-223 Troubleshooting

ENGLISH

Troubleshooting

Options & Expander Modules

Options

BC-100 Bench

A comfortable bench styled to match your Yamaha YDP-223.

HPE-160 Stereo Headphones

High-performance lightweight dynamic headphones with extra-soft ear pads.

Problem Possible Cause and Solution

The YDP-223 does not turn on. The YDP-223 has not been plugged in properly. Securely insert the female plug into

the socket on the YDP-223, and the male plug into a proper AC outlet (page 11).

A click or pop is heard when the power is

turned on or off.

This is normal when electrical current is being applied to the instrument.

Noise is heard from the speakers or head-

phones.

The noise may be due to interference caused by the use of a mobile phone in close

proximity to the YDP-223. Turn off the mobile phone, or use it further away from the

YDP-223.

The overall volume is low, or no sound is

heard.

• The Master Volume is set too low; set it to an appropriate level using the [MASTER

VOLUME] control.

• Make sure a pair of headphones is not connected to the headphones jack (when the

SPEAKER switch is set to the “NORMAL” position). If the SPEAKER switch is set to

the “OFF” position, set it to “NORMAL” or “ON” (page 12).

• Make sure that Local Control (page 41) is ON.

The speakers do not switch off when a pair of

headphones is connected.

The SPEAKER switch may be switched “ON.” Set the SPEAKER switch to the “NOR-

MAL” position (page 12).

The damper pedal has no effect, or the sound

continuously sustains even when the damper

pedal is not pressed.

The pedal cable/plug may not be properly connected. Make sure to securely insert the

pedal plug into the proper jack (pages 53–55).

TIP

If appears on the display, an internal malfunction has occurred. In this case, contact your Yamaha dealer.

YDP-223 Keyboard Stand Assembly

ENGLISH

Keyboard Stand Assembly

CAUTION

• Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accor-

dance with the sequence given below.

• Assembly should be carried out by at least two persons.

• Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage.

• Be sure to tighten up all screws upon completing assembly of each unit.

•To disassemble, reverse the assembly sequence given below.

Remove the following parts from the package.

1. Attach the side panels to the pedal box.

2. Attach the rear panel.

Have a Phillips-head (+) screwdriver ready.

TIP

A headphone hanger is included in the YDP-223 package.

You can attach a headphone hanger on the YDP-223 to hang

the headphones (page 12).

Assembly Parts

6 × 25 mm long screws ×4 1

4 × 12 mm thin screws ×2

Cord holders × 2

6 × 16 mm short screws ×4 2

20 mm tapping screws

Pedal box

Rear panel

Main unit

Side

panel

(left)

Side

panel

(right)

Bundled pedal

cord inside

AC power cord

Side panel

(left)

Side panel

(right)

(1) Untie and straighten

out the bundled cord

attached to the bot-

tom of the pedal box.

Don’t discard the

vinyl tie, you’ll need it

later in step 5.

(2) Use the four 6×25 mm long

screws 1 to attach the

pedal box. First attach one

side panel, then attach the

other side panel.

(2) Secure the top of the

rear panel to the side

panel brackets using two

4×12 mm thin screws 3.

(3) Secure the bottom

of the rear panel to

the pedal box using

four 4×20 mm tap-

ping screws 4.

(1) Place the bot-

tom edges of the rear

panel on the feet’s pro-

truding edges, with the

panel slightly angled

as shown in the illus-

tration.

Then, align the top part

of the panel with the

side panels.

YDP-223 Keyboard Stand Assembly

ENGLISH

3. Mount the main unit.

CAUTION

• Fingers can become pinched between the main

unit and the rear or side panels, be extra careful

so as not to drop the main unit.

• Do not hold the keyboard in any position other

than the position shown in the illustration.

4. Fix the main unit.

5. Connect the pedal cord.

6. Set the voltage selector and connect the

power cord.

Voltage Selector

Before connecting the AC power cord, check the setting

of the voltage selector which is provided in some areas.

To set the selector for 110V, 127V, 220V or 240V main

voltages, use a “minus” screwdriver to rotate the selector

dial so that the correct voltage for your region appears

next to the pointer on the panel. The voltage selector is

set at 240V when the unit is initially shipped. After the

proper voltage has been selected, connect the AC power

cord to the AC INLET and an AC wall outlet. A plug

adaptor may be also provided in some areas to match the

pin conﬁguration of the AC wall outlets in your area.

WARNING

An improper voltage setting can cause serious

damage to the YDP-223 or result in improper

operation.

Be sure to place your hands at least 10 cm

from either end of the main unit when positioning it.

At least

10 cm

(1) Center the main unit to pro-

duce equal clearance on

the left and right sides.

(2) Use 6x16 mm short screws

2 to secure the main unit

from the front.

PEDAL

(1) Insert the pedal cord plug to the

pedal connector from the front.

(3) Use a vinyl tie

to take up any

slack in the

pedal cord.

(2) Attach the cord holders to

the rear panel as shown,

then clip the cord into the

holders.

240

127

110

220

YDP-223 Keyboard Stand Assembly

ENGLISH

7. Set the adjuster.

After completing the assembly, please

check the following.

When moving the instrument after assembly, always

hold the bottom of the main unit.

CAUTION

Do not hold the key cover or top portion. Improper

handling can result in damage to the instrument or

personal injury.

• Are there any parts left over?

➝ Review the assembly procedure and correct any

errors.

• Is the YDP-223 clear of doors and other movable

ﬁxtures?

➝ Move the YDP-223 to an appropriate location.

• Does the YDP-223 make a rattling noise when

you shake it?

➝ Tighten all screws.

• Does the pedal box rattle or give way when you

step on the pedals?

➝ Tu rn the adjuster so that it is set ﬁrmly against

the ﬂoor.

• Are the pedal and power cords inserted securely

into the sockets?

➝ Check the connection.

• If the main unit creaks or is otherwise unsteady

when you play on the keyboard, refer to the

assembly diagrams and retighten all screws.

Rotate the adjuster until it comes in ﬁrm contact with the

ﬂoor surface.

Key cover

Top portion

YDP-223 Preset Voice List

ENGLISH

Preset Voice List

Demo Song List

The demonstration pieces listed above are short rearranged excerpts the original compositions.

Voice Name

Stereo

Sampling

Touch

Response

Dynamic

Sampling

Key-Off

Sampling

Voice Descriptions

GRANDPIANO 1

Recorded samples from a full concert grand piano. Perfect

for classical compositions as well as any other style that

requires acoustic piano.

GRANDPIANO 2

Spacious and clear piano with bright reverb. Good for popu-

lar music.

E.PIANO 1

An electronic piano sound created by FM synthesis. Good

for popular music.

E.PIANO 2

The sound of an electric piano using hammer-struck metallic

“tines”. Soft tone when played lightly, and an aggressive

tone when played hard.

HARPSICHORD 1

The deﬁnitive instrument for baroque music. Since harpsi-

chord uses plucked strings, there is no touch response.

There is, however, a characteristic additional sound when

the keys are released.

HARPSICHORD 2

Mixes the same voice an octave higher for a more brilliant

tone.

VIBRAPHONE

Vibraphone played with relatively soft mallets. The tone

becomes more metallic the harder you play.

CHURCH ORGAN 1

This is a typical pipe organ sound (8 feet + 4 feet + 2 feet).

Good for sacred music from the Baroque period.

CHURCH ORGAN 2

This is the organ's full coupler sound often associated with

Beach’s “Toccata and Fugue”.

JAZZ ORGAN

The sound of a “tonewheel” type electric organ. Often heard

in jazz and rock idioms.

STRINGS 1

Stereo-sampled, large-scale strings ensemble with realistic

reverb. Try combining this voice with piano in the DUAL

mode.

STRINGS 2

Spacious strings ensemble with a slow attack. Try combining

this voice with a piano or electric piano in the DUAL mode.

CHOIR

A big, spacious choir voice. Perfect for creating rich harmo-

nies in slow pieces.

GUITAR

Warm and natural-sounding nylon guitar. Enjoy the quiet

ambience of nylon strings.

*1. Dynamic Sampling provides multiple velocity-switched samples to accurately simulate the timbral response of

an acoustic instrument.

*2. Contains a very subtle sample that is produced when the keys are released.

Voice Name Title Composer

GRAND PIANO1 Consolation No.3 F. Liszt

HARPSICHORD1 Gavotte

J.S. Bach

HARPSICHORD2 Invention No.1

YDP-223 Index

ENGLISH

Index

Numerics

50 Greats for the Piano ...................................................17

50 Piano Preset Songs .....................................................17

A-B Repeat for 50 Preset Songs ......................................20

Accessories.........................................................................8

Adding Variations to the Sound.....................................22

Adjust

Brilliance ..............................................................16, 22

Tempo (50 Piano Preset Songs) ...............................17

Tempo (Recorded Songs) .........................................32

Volume (50 Piano Preset Songs) ..............................17

Volume (Demo) ........................................................16

Volume (Metronome) ..............................................40

ALL (LED display) ..........................................................17

Assembly....................................................................53–55

AUX IN ......................................................................14, 47

AUX OUT..................................................................14, 46

Backup Functions............................................................44

BRILLIANCE.............................................................14, 22

Center Pedal ..............................................................15, 22

Combining Two Voices (Dual mode)............................26

Connecting a Personal Computer..................................48

Connections.....................................................................46

Connectors ......................................................................46

Damper Pedal ............................................................15, 21

DEMO........................................................................14, 16

Demo Song List ...............................................................56

Detailed Settings (FUNCTION).....................................34

Dual mode .................................................................26, 39

EFFECT......................................................................14, 23

Factory Setting List .........................................................60

Fine Tuning of the Pitch.................................................37

FUL (LED display)..........................................................29

FUNCTION ........................................................14, 37–44

Basic Procedure.........................................................35

Function Parameter List .................................................60

HOST SELECT....................................................15, 47, 50

HST (LED display).......................................................... 48

Key Cover ........................................................................10

LED display .....................................................................14

Left Pedal............................................................. 15, 22, 40

List

Demo Song ................................................................56

Factory Setting........................................................... 60

Functions................................................................... 34

Preset Voice ............................................................... 56

MASTER VOLUME..................................................11, 14

METRONOME .........................................................14, 27

Metronome Volume .......................................................40

MIDI ................................................................................45

MIDI [IN] [OUT] [THRU] .....................................15, 47

MIDI cables .........................................................45, 50, 51

MIDI connectors....................................................... 45, 50

MIDI Data Format..........................................................61

MIDI driver .....................................................................49

MIDI Functions ..............................................................41

Music Rest .......................................................................10

PEDAL jack ...............................................................14, 47

PHONES.................................................................... 12, 15

Pitch ➝ Fine Tuning of the Pitch ..................................37

POWER .....................................................................11, 14

YDP-223 Index

ENGLISH

Practicing a One-Hand Part Using 50 Preset Songs......18

Precautions ....................................................................6–7

PRESET......................................................................14, 17

Preset Song Part...............................................................40

Preset songs ➝ 50 Piano Preset Songs ...........................17

Preset Voice List ..............................................................56

REC ➝ Recording .....................................................14, 28

Recording.........................................................................28

Initial Settings............................................................31

Re-recording....................................................................29

REVERB.....................................................................14, 22

Right Pedal.................................................................15, 21

rnd (LED display)............................................................17

Scale..................................................................................38

Scn (LED display)............................................................52

Serial cable .................................................................49, 51

Soft Pedal .............................................................15, 22, 40

Sostenute Pedal..........................................................15, 22

SPEAKER...................................................................12, 15

Specifications...................................................................66

START/STOP (Demo)....................................................16

START/STOP (METRONOME)..............................14, 27

Start/Stop (Pedal)............................................................33

START/STOP (SONG) ...................................................14

Start/Stop playback

50 Piano Preset Songs................................................17

Demonstration Tunes ...............................................16

Recorded Songs .........................................................32

Useful Playback Functions........................................33

Start/Stop recording........................................................29

Synchro Start

50 Piano Preset Songs................................................19

Recorded Songs .........................................................33

TEMPO................................................................14, 17, 32

TEMPO (METRONOME) .............................................27

TO HOST ..................................................................15, 45

TOUCH .....................................................................14, 24

Touch Sensitivity.............................................................24

Track Playback On and Off ............................................33

TRACK1/2 (50 Piano Preset Songs)...............................18

TRACK1/2 (Recording)..................................................29

Transporting .....................................................................8

TRANSPOSE.............................................................14, 25

Troubleshooting.............................................................. 52

Tuning ➝ Fine Tuning of the Pitch............................... 37

USB ..................................................................................51

VOICE ....................................................................... 14, 21

YDP-223

Appendix/Anhang/

Annexe/Apéndice

This section introduces reference material.

Dieser Abschnitt stellt Referenzmaterial vor.

Cette section présente le matérial de référence.

En esta sección se incluye material de referencia.

Factory Setting List / Liste der Vorgabeeinstellungen / Liste des réglages / Lista de ajustes de fábrica.............. 60

MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI................... 61

MIDI Implementation Chart / MIDI Implementierung stabelle /

Feuille d’implantation MIDI / Gráﬁca de implementación MIDI ................................................................... 65

Speciﬁcations / Technische Daten / Caractéristiques techniques / Especiﬁcaciones .......................................... 66

YDP-223 Appendix/Anhang/Annexe/Apéndice

Factory Setting List / Liste der Vorgabeeinstellungen /

Liste des réglages / Lista de ajustes de fábrica

Function

Function Default Backup Group

Voice GRAND PIANO 1

F8.1

Dual Mode OFF

Reverb Type Preset for each voice

Reverb Depth Preset for each voice

Effect Type Preset for each voice

Effect Depth Preset for each voice

Touch Sensitivity MEDIUM

Volume in the FIXED Mode 64

Metronome OFF —

Metronome Time Signature 0 (no accent) F8.1

Tempo 120 —

Transpose 0 F8.3

Function Default Backup Group

F1 Tuning A3=440Hz

F8.3F2.1 Scale 1 (Equal Temperament)

F2.2 Base Note C

F3.1 Dual Balance Preset for each voice combination

F8.1

F3.2 Dual Detune Preset for each voice combination

F3.3, F3.4 Dual Octave Shift Preset for each voice combination

F3.5, F.3.6 Dual Effect Depth Preset for each voice combination

F4.1 Left Pedal Mode 1 (Soft Pedal)

F8.4

F4.2 Soft Pedal Effect Depth 3

F5 Metronome Volume 10

F8.1

F6 Preset Song Part Cancel Volume 5

F7.1 MIDI Transmit Channel 1

F8.2

F7.2 MIDI Receive Channel ALL

F7.3 Local Control ON

F7.4 Program Change Send & Receive ON

F7.5 Control Change Send & Receive ON

F7.6 MIDI Transmit Transpose 0

F8 Backup All OFF Always backed up

YDP-223 Appendix/Anhang/Annexe/Apéndice

MIDI Data Format / MIDI-Datenformat /

Format des données MIDI / Formato de datos MIDI

If you’re already very familiar with MIDI, or are using a

computer to control your music hardware with computer-

gener-ated MIDI messages, the data provided in this section

can help you to control the YDP-223.

Falls Sie bereits mit MIDI vertraut sind oder einen

Computer zur Erzeugung von MIDI-Steuermeldungen für die

Instrumente verwenden, können Sie sich zur Steuerung des

YDP-223 nach den im folgenden Abschnitt aufgeführten

Speziﬁkationen richten.

Si vous êtes très familier avec l’interface MIDI ou si vous

utilisez un ordinateur pour commander votre matériel de

musique au moyen de messages MIDI générés par

ordinateur, les données suivantes vous seront utiles et vous

aideront à commander le YDP-223.

SI usted está ya familiarizado con MIDI, o si emplea una

computadora para controlar sus aparatos musicales con

mensajes MIDI generados por computadora, los datos

proporcionados en esta sección le ayudarán a controlar la

YDP-223.

1. NOTE ON/OFF

Data format: [9nH] -> [kk] -> [vv]

9nH = Note ON/OFF event (n = channel number)

kk = Note number (Transmit: 09H ~ 78H = A-2 ~ C8 /

Receive: 00H ~ 7FH = C-2 ~ G8)*

vv = Velocity (Key ON = 01H ~ 7FH, Key OFF = 00H)

Data format: [8nH] -> [kk] -> [vv] (reception only)

8nH = Note OFF event (n = channel number)

kk = Note number: 00H ~ 7FH = C-2 ~ G8

vv = Velocity

* If received value exceeds the supported range for the

selected voice, the note is adjusted by the necessary num-

ber of octaves.

2. CONTROL CHANGE

Data format: [BnH] -> [cc] -> [vv]

BnH = Control change (n = channel number)

cc = Control number

vv = Data Range

(1) Bank Select

ccH Parameter Data Range (vvH)

00H Bank Select MSB 00H:Normal

20H Bank Select LSB 00H...7FH

Bank selection processing does not occur until receipt of

next Program Change message.

(2) Main Volume (reception only)

ccH Parameter Data Range (vvH)

07H Volume MSB 00H...7FH

(3) Expression

ccH Parameter Data Range (vvH)

0BH Expression MSB 00H...7FH

(4) Damper

ccH Parameter Data Range (vvH)

40H Damper MSB 00H...7FH

(5) Sostenuto

ccH Parameter Data Range (vvH)

42H Sostenuto 00H-3FH:off, 40H-7FH:on

(6) Soft Pedal

ccH Parameter Data Range (vvH)

43H Soft Pedal 00H-3FH:off, 40H-7FH:on

(7) Effect1 Depth (Reverb Send Level)

ccH Parameter Data Range (vvH)

5BH Effect1 Depth 00H...7FH

Adjusts the reverb send level.

(8) Effect4 Depth (Variation Effect Send Level)

ccH Parameter Data Range (vvH)

5EH Effect4 Depth 00H...7FH

3. MODE MESSAGES

Data format: [BnH] -> [cc] -> [vv]

BnH = Control event (n = channel number)

cc = Control number

vv = Data Range

(1) All Sound Off

ccH Parameter Data Range (vvH)

78H All Sound Off 00H

Switches off all sound from the channel. Does not reset Note

On and Hold On conditions established by Channel Messages.

(2) Reset All Controllers

ccH Parameter Data Range (vvH)

79H Reset All Controllers 00H

Resets controllers as follows.

Controller Value

Expression 127 (max)

Damper Pedal 0 (off)

Sostenuto 0 (off)

Soft Pedal 0 (off)

(3) Local Control (reception only)

ccH Parameter Data Range (vvH)

7AH Local Control 00H (off), 7FH (on)

(4) All Notes Off

ccH Parameter Data Range (vvH)

7BH All Notes Off 00H

Switches OFF all the notes that are currently ON on the spec-

iﬁed channel. Any notes being held by the damper or soste-

nuto pedal will continue to sound until the pedal is released.

(5) Omni Off (reception only)

ccH Parameter Data Range (vvH)

7CH Omni Off 00H

Same processing as for All Notes Off.

(6) Omni On (reception only)

ccH Parameter Data Range (vvH)

7DH Omni On 00H

Same processing as for All Notes Off.

(7) Mono (reception only)

ccH Parameter Data Range (vvH)

7EH Mono 00H

Same processing as for All Sound Off.

(8) Poly (reception only)

ccH Parameter Data Range (vvH)

7FH Poly 00H

Same processing as for All Sound Off.

• When control change reception is turned OFF in the Function

mode, control change data will not be transmitted or received

except for Bank Select and Mode messages.

• Local on/off, OMNI on/off are not transmitted. (The appropriate

note off number is supplied with “All Note Off” transmission).

• When a voice bank MSB/LSB is received, the number is

stored in the internal buffer regardless of the received order,

then the stored value is used to select the appropriate voice

when a program change message is received.

• The Multi-timbre and Poly modes are always active. No

change occurs when OMNI ON, OMNI OFF, MONO, or POLY

mode messages are received.

YDP-223 Appendix/Anhang/Annexe/Apéndice

4. PROGRAM CHANGE

Data format: [CnH] -> [ppH]

CnH = Program event (n = channel number)

ppH = Program change number

P. C .#=Program Change number

• When program change reception is turned OFF in the Func-

tion mode, no program change data is transmitted or

received. Also, Bank MSB/LSB is not transmitted or received.

5. SYSTEM REALTIME MESSAGES

[rrH]

F8H: Timing clock

FAH: Start

FCH: Stop

FEH: Active sensing

• Caution: If an error occurs during MIDI reception, the Damper,

Sostenuto, and Soft effects for all channels are turned off and

an All Note Off occurs.

6. SYSTEM EXCLUSIVE MESSAGES

(Yamaha MIDI Format)

Panel Data Transmit

Data format: [F0H] -> [43H] -> [0nH] -> [7CH] -> ... -> [F7H]

F0H, 43H, 0nH, 7CH (n: channel number)

00H, 2DH (data length)

43H, 4CH, 20H, 20H (Model Name)

43H, 4CH, 50H, 27H, 30H, 32H (Model Name)

30H, 30H (version x, y)

[PANEL DATA]

[CHECK SUM (1byte)] = 0-(43H+4CH+20H+......+Data end)

F7H

• Panel Data Contents

•Panel data send requests cannot be received.

7. SYSTEM EXCLUSIVE MESSAGES

(Universal System Exclusive)

(1) Universal Realtime Message

Data format: [F0H] -> [7FH] -> [XnH] -> [04H] -> [01H] ->

[llH] -> [mmH] -> [F7H]

MIDI Master Volume

• Simultaneously changes the volume of all channels.

• When a MIDI master volume message is received, the volume

only has affect on the MIDI receive channel, not the panel

master volume.

F0H = Exclusive status

7FH = Universal Realtime

7FH = ID of target device

04H = Sub-ID #1=Device Control Message

01H = Sub-ID #2=Master Volume

llH = Volume LSB

mmH =

Volume MSB

F7H = End of Exclusive

F0H = Exclusive status

7FH = Universal Realtime

XnH = When n is received n=0~F, whichever is received.

X = don’t care

04H = Sub-ID #1=Device Control Message

01H = Sub-ID #2=Master Volume

llH = Volume LSB

mmH =

Volume MSB

F7H = End of Exclusive

MSB LSB

P.C.#

GRANDPIANO 1 0 122 0

GRANDPIANO 2 0 112 0

E.PIANO 1 0 122 5

E.PIANO 2 0 122 4

HARPSICHORD 1 0 122 6

HARPSICHORD 2 0 123 6

VIBRAPHONE 0 122 11

CHURCH ORGAN 1 0 123 19

CHURCH ORGAN 2 0 122 19

JAZZ ORGAN 0 122 16

STRINGS 1 0 122 48

STRINGS 2 0 122 49

CHOIR 0 122 52

GUITAR 0 122 24

Data Transmission Reception

F8H

Transmitted every

96 clocks

Received as 96-clock tempo timing

when MIDI clock is set to External

FAHRecorder start

Recorder start

Not received when the MIDI clock is

set to Internal.

FCH Recorder stop

Recorder stop

Not received when the MIDI clock is

set to Internal.

FEH

Transmitted every

200 milliseconds

If a signal is not received via MIDI for

more than 400 milliseconds, the same

processing will take place for All

Sound Off, All Notes Off and Reset All

Controllers as when those signals are

received.

(1) 1'st Voice

(2) Dual On/Off

(3) Dual Voice

(4) Dual Balance

(5) Dual Detune

(6) Dual Voice1 Octave

(7) Dual Voice2 Octave

(8) Dual Voice1 Effect Depth

(9) Dual Voice2 Effect Depth

(10)

(11)

(12)

(13)

(14)

(15)

(16)

(17)

(18)

(19) Reverb Type 1

(20) Reverb Type 2

(21) Reverb Depth 1

(22) Reverb Depth 2

(23) Effect Type 1

(24) Effect Type 2

(25) Effect Depth

(26)

(27) Touch Sensitivity

(28) Fixed Data

(29) Left Pedal

(30) Soft Pedal Depth

(31) Absolute tempo low byte

(32) Absolute tempo high byte

(33) Key-Off Sampling Depth

YDP-223 Appendix/Anhang/Annexe/Apéndice

(2) Universal Non-Realtime Message (GM On)

General MIDI Mode On

Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->

[F7H]

F0H = Exclusive status

7EH = Universal Non-Realtime

7FH = ID of target device

09H = Sub-ID #1=General MIDI Message

01H = Sub-ID #2=General MIDI On

F7H = End of Exclusive

F0H = Exclusive status

7EH = Universal Non-Realtime

XnH = When received, n=0~F.

X = don’t care

09H = Sub-ID #1=General MIDI Message

01H = Sub-ID #2=General MIDI On

F7H = End of Exclusive

When the General MIDI mode ON message is received, the

MIDI system will be reset to its default settings.

This message requires approximately 50ms to execute, so

sufﬁ-cient time should be allowed before the next message is

sent.

8. SYSTEM EXCLUSIVE MESSAGES (XG Standard)

(1) XG Native Parameter Change

Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->

[mmH] -> [llH] -> [ddH] -> [F7H]

F0H = Exclusive status

43H = YAMAHA ID

1nH = When received, n=0~F.

When transmitted, n=0.

4CH = Model ID of XG

hhH = Address High

mmH =

Address Mid

llH = Address Low

ddH = Data

F7H = End of Exclusive

Data size must match parameter size (2 or 4 bytes).

When the XG System On message is received, the MIDI sys-

tem will be reset to its default settings.

The message requires approximately 50ms to execute, so

sufﬁcient time should be allowed before the next message is

sent.

(2) XG Native Bulk Data (reception only)

Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->

[bbH] -> [hhH] -> [mmH] -> [llH] ->[ddH] ->...->

[ccH] -> [F7H]

F0H = Exclusive status

43H = YAMAHA ID

0nH = When received, n=0~F.

When transmitted, n=0.

4CH = Model ID of XG

aaH = ByteCount

bbH = ByteCount

hhH = Address High

mmH =

Address Mid

llH = Address Low

ddH = Data

| |

ccH = Check sum

F7H = End of Exclusive

• Receipt of the XG SYSTEM ON message causes reinitializa-

tion of relevant parameters and Control Change values. Allow

sufﬁcient time for processing to execute (about 50 msec)

before sending the YDP-223 another message.

• XG Native Parameter Change message may contain two or

four bytes of parameter data (depending on the parameter

size).

•For information about the Address and Byte Count values,

refer to Table 1 below. Note that the table’s Total Size value

gives the size of a bulk block. Only the top address of the

block (00H, 00H, 00H) is valid as a bulk data address.

9. SYSTEM EXCLUSIVE MESSAGES

(Digital Piano MIDI Format)

Data format:

[F0H] -> [43H] -> [73H] -> [xxH] -> [nnH] -> [F7H]

F0H = Exclusive status

43H = Yamaha ID

73H = Digital Piano ID

01H = Product ID (YDP common)

7F= Extended Product ID

xxH = Product ID (YDP-223: 25H)

nnH = Substatus

nn Control

02H Internal MIDI clock

03H External MIDI clock

06H Bulk Data (the bulk data follows 06H)

F7H = End of Exclusive

* When nn=02H or 03H, YDP common ID (01H) is rec-

ognized as well as 75H.

BULK DUMP FORMAT

F0H, 43H, 73H

75F, xxH = Product ID (YDP-223: 25H)

06H = Bulk ID

05H = Sequence data

0nH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH = Data length

[BULK DATA] =

[CHECK SUM (1byte)] = 0-sum (BULK DATA)

F7H = End of Exclusive

10.

SYSTEM EXCLUSIVE MESSAGES (Special Control)

Data format: [F0H] -> [43H] -> [73H] -> [66H] -> [11H] ->

[0nH] -> [ccH] -> [vvH] -> [F7H]

F0H = Exclusive status

43H = Yamaha ID

73H = Digital Piano ID

7FH = Extended Product ID

xxH = Product ID (YDP-223: 25H)

11H = Special control

0nH = Control MIDI change (n=channel number)

cc = Control number

vv = Value

F7H = End of Exclusive

Control 0n ccH vvH

Metronome Always 00H 1BH 00H : off

01H : –

02H : 2/4

03H : 3/4

04H : 4/4

05H : 5/4

06H : 6/4

7FH : No accent

Damper Level

ch: 00H-0FH 3DH(Sets the Damper Level

for each channel)

00H-7FH

Channel Detune

ch: 00H-0FH 43H (Sets the Detune value

for each channel)

00H-7FH

Voice Reserve

ch: 00H-0FH 45H 00H : Reserve off

7FH : on*

When Volume, Expression is received for Reserve On, they

will be effective from the next Key On. Reserve Off is normal.

11. SYSTEM EXCLUSIVE MESSAGES (Others)

Data format:

[F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H]

-> [00H] -> [mmH] -> [

H] -> [ccH] -> [F7H]

Master Tuning (XG and last message priority) simultaneously

changes the pitch of all channels.

F0H = Exclusive Status

43H = Yamaha ID

1nH = When received, n=0~F.

When transmitted, n=0.

27H = Model ID of TG100

30H = Sub ID

00H =

mmH = Master Tune MSB

llH = Master Tune LSB

ccH = don’t care (under 7FH)

F7H = End of Exclusive

YDP-223 Appendix/Anhang/Annexe/Apéndice

MIDI Parameter Change table (SYSTEM)

Address (H) Size (H) Data (H) Parameter Description Default value (H)

00 00 00 4 020C - 05F4(*1) MASTER TUNE -50 - +50[cent] 00 04 00 00

01 1st bit 3 - 0 ➝ bit 15 - 12 400

02 2nd bit 3 - 0 ➝ bit 11 - 8

03 3rd bit 3 - 0 ➝ bit 7 - 4

4th bit 3 - 0 ➝ bit 3 - 0

04 1 00 - 7F MASTER VOLUME 0 - 127 7F

05 1 — —

06 1 34 - 4C(*2) TRANSPOSE -12 - +12[semitones] 40

7E 00 XG SYSTEM ON 00=XG sytem ON

7F 00 RESET ALL PARAMETERS 00=ON (receive only)

TOTAL SIZE 07

*1: Values lower than 020CH select -50 cents. Values higher than 05F4H select +50 cents.

*2: Values from 28H through 33H are interpreted as -12 through -1. Values from 4DH through 58H are interpreted as +1 through +12.

MIDI Parameter Change table (EFFECT 1)

Refer to the “Effect MIDI Map” for a complete list of Reverb, Chorus and Variation type numbers.

Address (H) Size (H) Data (H) Parameter Description Default value (H)

02 01 00 2 00-7F REVERB TYPE MSB Refer to Effect MIDI Map 01(=HALL1)

00-7F REVERB TYPE LSB 00 : basic type 00

02 01 40 2 00-7F VARIATION TYPE MSB Refer to Effect MIDI Map 00(=Effect off)

00-7F VARIATION TYPE LSB 00 : basic type 00

• “VARIATION” refers to the EFFECT on the panel.

MIDI Parameter Change table (MULTI PART)

Address (H) Size (H) Data (H) Parameter Description Default value (H)

08 nn 11 1 00 - 7F DRY LEVEL 0 - 127 7F

nn = Part Number

• Effect MIDI Map

REVERB

MSB LSB

ROOM 02H 10H

HALL 1 01H 10H

HALL 2 01H 11H

STAGE 03H 10H

Sound board 03H 12H

EFFECT

MSB LSB

CHORUS 42H 10H

PHASER 48H 10H

TREMOLO 46H 10H

DELAY 05H 10H

YDP-223 Appendix/Anhang/Annexe/Apéndice

MIDI Implementation Chart

YAMAHA [Digital Piano] Date: 10 May, 2002

Model: YDP-223 MIDI Implementation Chart Version: 1.0

Mode 1: OMNI ON, POLY Mode 2: OMNI ON, MONO O : Yes

Mode 3: OMNI OFF, POLY Mode 4: OMNI OFF, MONO X : No

Function Transmitted Recognized Remarks

Basic Default

Channel Changed

1 - 16

Default

Mode Messages

Altered

*****************

1 *1

Poly Mode only

Note

Number : True voice

9 - 120

*****************

0 - 127

Velocity Note ON

Note OFF

O 9nH, v=1 - 127

O 9nH, v=0

O 9nH, v=1 - 127

O 9nH, v=0 or 8nH

After Key’s

Touch Ch’s

Pitch Bender X X

Control Change 0, 32

Bank Select

Volume

Expression

Damper

Sostenuto

Soft pedal

Reverb Depth

Effect Depth

Program

Change : True #

*****************

System Exclusive O O

: Song Position

Common : Song Select

: Tune

System : Clock

Real Time : Commands

: All sounds off

Aux: Reset All Controllers

: Local ON/OFF

Messages : All Notes OFF

: Active Sense

: Reset

O (120, 126, 127)

O (121)

O (122)

O (123 - 125)

Notes : *1 = Recieve Mode is always multi timbre and Poly mode.

YDP-223 Appendix/Anhang/Annexe/Apéndice

Speciﬁcations / Technische Daten /

Caractéristiques techniques / Especiﬁcaciones

*Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change

or modify products or speciﬁcations at any time without prior notice. Since speciﬁcations, equipment or options may not be the

same in every locale, please check with your Yamaha dealer.

*Die technischen Daten und Beschreibungen in dieser Bedienungsanleitung dienen nur der Information. Yamaha Corp. behält sich

das Recht vor, Produkte oder deren technische Daten jederzeit ohne vorherige Ankündigung zu verändern oder zu modiﬁzieren. Da

die technischen Daten, das Gerät selbst oder Sonderzubehör nicht in jedem Land gleich sind, setzen Sie sich im Zweifel bitte mit

Ihrem Yamaha-Händler in Verbindung.

*Les caractéristiques techniques et les descriptions du mode d’emploi ne sont données que pour information. Yamaha Corp. se

réserve le droit de changer ou modiﬁer les produits et leurs caractéristiques techniques à tout moment sans aucun avis. Du fait que

les caractéristiques techniques, les équipements et les options peuvent différer d’un pays à l’autre, adressez-vous au distributeur

Yamaha le plus proche.

* Las especiﬁcaciones y descripciones de este manual del propietario tienen sólo el propósito de servir como información. Yamaha

Corp. se reserva el derecho a efectuar cambios o modiﬁcaciones en los productos o especiﬁcaciones en cualquier momento sin pre-

vio aviso. Puesto que las especiﬁcaciones, equipos u opciones pueden no ser las mismas en todos los mercados, solicite información

a su distribuidor Yamaha.

Keyboard 88 keys (A-1 - C7)

Sound Source AWM Stereo Sampling

Polyphony 64 Notes Max.

Voice Selection 14

Effect Reverb, Effect, Brilliance

Volume Master Volume

Controls Dual, Metoronome, Transpose, Touch (Hard/Midium/Soft/Fixed), Functions, Speaker ON/OFF

Recording/Playback 2-track recording/playback (1 user song), Tempo Adjustment, Synchro Start

Pedal Damper, Sostenuto, Soft

Demo Songs 14 voice Demo Songs, 50 preset Songs

Jacks/Connectors

MIDI (IN/OUT/THRU), PHONES × 2, AUX IN, AUX OUT(L/L+R,R), AUX OUT (LEVEL

FIXED)(L,R), TO HOST

Main Ampliﬁers 20W × 2

Speakers 16cm × 2

Dimensions (W × D × H)

(with music rest)

1370mm × 518mm × 850mm

[53 15/16" × 20 3/8" × 33 7/16"]

(1370mm × 518mm × 1022mm)

[53 15/16" × 220 3/8" × 40 1/4"]

Weight 51kg (112lbs., 7oz)

Accessories

Owner’s Manual, “50 greats for the Piano” (Music Book), Bench (included or optional depend-

ing on locale)

YDP-223

MEMO

YDP-223

MEMO

IMPORTANT SAFETY INSTRUCTIONS

INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,

AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.

WARNING- When using any electrical or electronic product,

basic precautions should always be followed. These precautions

include, but are not limited to, the following:

1. Read all Safety Instructions, Installation Instructions, Spe-

cial Message Section items, and any Assembly Instructions

found in this manual BEFORE making any connections, includ-

ing connection to the main supply.

2. Main Power Supply Veriﬁcation: Yamaha products are

manufactured speciﬁcally for the supply voltage in the area

where they are to be sold. If you should move, or if any doubt

exists about the supply voltage in your area, please contact your

dealer for supply voltage veriﬁcation and (if applicable) instruc-

tions. The required supply voltage is printed on the name plate.

For name plate location, please refer to the graphic found in the

Special Message Section of this manual.

3. This product may be equipped with a polarized plug (one

blade wider than the other). If you are unable to insert the plug

into the outlet, turn the plug over and try again. If the problem

persists, contact an electrician to have the obsolete outlet

replaced. Do NOT defeat the safety purpose of the plug.

4. Some electronic products utilize external power supplies

or adapters. Do NOT connect this type of product to any power

supply or adapter other than one described in the owners manual,

on the name plate, or speciﬁcally recommended by Yamaha.

5. WARNING: Do not place this product or any other

objects on the power cord or place it in a position where anyone

could walk on, trip over, or roll anything over power or connect-

ing cords of any kind. The use of an extension cord is not recom-

mended! If you must use an extension cord, the minimum wire

size for a 25’ cord (or less) is 18 AWG. NOTE: The smaller the

AWG number, the larger the current handling capacity. For

longer extension cords, consult a local electrician.

6. Ventilation: Electronic products, unless speciﬁcally

designed for enclosed installations, should be placed in locations

that do not interfere with proper ventilation. If instructions for

enclosed installations are not provided, it must be assumed that

unobstructed ventilation is required.

7. Temperature considerations: Electronic products should

be installed in locations that do not signiﬁcantly contribute to

their operating temperature. Placement of this product close to

heat sources such as; radiators, heat registers and other devices

that produce heat should be avoided.

8. This product was NOT designed for use in wet/damp loca-

tions and should not be used near water or exposed to rain.

Examples of wet/damp locations are; near a swimming pool, spa,

tub, sink, or wet basement.

9. This product should be used only with the components

supplied or; a cart, rack, or stand that is recommended by the

manufacturer. If a cart, rack, or stand is used, please observe all

safety markings and instructions that accompany the accessory

product.

10. The power supply cord (plug) should be disconnected

from the outlet when electronic products are to be left unused for

extended periods of time. Cords should also be disconnected

when there is a high probability of lightning and/or electrical

storm activity.

11. Care should be taken that objects do not fall and liquids are

not spilled into the enclosure through any openings that may exist.

12. Electrical/electronic products should be serviced by a

qualiﬁed service person when:

a. The power supply cord has been damaged; or

b. Objects have fallen, been inserted, or liquids have been

spilled into the enclosure through openings; or

c. The product has been exposed to rain: or

d. The product dose not operate, exhibits a marked change

in performance; or

e. The product has been dropped, or the enclosure of the

product has been damaged.

13. Do not attempt to service this product beyond that

described in the user-maintenance instructions. All other servic-

ing should be referred to qualiﬁed service personnel.

14. This product, either alone or in combination with an

ampliﬁer and headphones or speaker/s, may be capable of pro-

ducing sound levels that could cause permanent hearing loss. DO

NOT operate for a long period of time at a high volume level or

at a level that is uncomfortable. If you experience any hearing

loss or ringing in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

15. Some Yamaha products may have benches and/or accessory

mounting ﬁxtures that are either supplied as a part of the product

or as optional accessories. Some of these items are designed to be

dealer assembled or installed. Please make sure that benches are

stable and any optional ﬁxtures (where applicable) are well

secured BEFORE using. Benches supplied by Yamaha are

designed for seating only. No other uses are recommended.

PLEASE KEEP THIS MANUAL

92-469-2

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

(2 wires)

• This applies only to products distributed by Yamaha-Kemble Music

(U.K.) Ltd.

(polarity)

• This applies only to products distributed by Yamaha Canada Music

Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada

Musique Ltée.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instruc-

tions contained in this manual, meets FCC require-

ments. Modiﬁcations not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2. IMPORTANT: When connecting this product to acces-

sories and/or another product use only high quality

shielded cables. Cable/s supplied with this product

MUST be used. Follow all installation instructions. Fail-

ure to follow instructions could void your FCC authoriza-

tion to use this product in the USA.

3. NOTE: This product has been tested and found to com-

ply with the requirements listed in FCC Regulations,

Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices. This equipment generates/

uses radio frequencies and, if not installed and used

according to the instructions found in the users manual,

may cause interference harmful to the operation of

other electronic devices. Compliance with FCC regula-

tions does not guarantee that interference will not occur

in all installations. If this product is found to be the

source of interference, which can be determined by

turning the unit “OFF” and “ON”, please try to eliminate

the problem by using one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfac-

tory results, please contact the local retailer authorized

to distribute this type of product. If you can not locate

the appropriate retailer, please contact Yamaha Corpo-

ration of America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this appa-

ratus may not correspond with the coloured makings iden-

tifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to

the terminal which is marked with the letter L or coloured

RED.

Making sure that neither core is connected to the earth ter-

minal of the three pin plug.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA

PRISE ET POUSSER JUSQU’AU FOND.

For details of products, please contact your nearest Yamaha or the

authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou

au distributeur le plus proche de vous ﬁgurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de Mexico S.A. De C.V.,

Departamento de ventas

Javier Rojo Gomez No.1149, Col. Gpe Del

Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.

Tel: 686-00-33

BRAZIL

Yamaha Musical do Brasil LTDA.

Av. Rebouças 2636, São Paulo, Brasil

Tel: 011-853-1377

ARGENTINA

Yamaha de Panamá S.A. Sucursal de Argentina

Viamonte 1145 Piso2-B 1053,

Buenos Aires, Argentina

Tel: 1-4371-7021

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha de Panamá S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: 507-269-5311

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

IRELAND

Danfay Ltd.

61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin

Tel: 01-2859177

GERMANY

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND

Yamaha Europa GmbH. Zweigniederlassung Zürich

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Europa GmbH. Zweigniederlassung Wien

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

THE NETHERLANDS

Yamaha Music Nederland

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

BELGIUM

Yamaha Music Belgium

Rue de Geneve (Genevastraat) 10, 1140 - Brussels,

Belgium

Tel: 02-726 6032

FRANCE

Yamaha Musique France,

Division Professionnelle

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.,

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha-Hazen Música, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid) Spain

Tel: 91-201-0700

GREECE

Philippe Nakas S.A.

Navarinou Street 13, P.Code 10680, Athens, Greece

Tel: 01-364-7111

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1

Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 8B

DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

F-Musiikki Oy

Kluuvikatu 6, P.O. Box 260,

SF-00101 Helsinki, Finland

Tel: 09 618511

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1

N-1345 Østerås, Norway

Tel: 67 16 77 70

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120

IS-128 Reykjavik, Iceland

Tel: 525 5000

OTHER EUROPEAN COUNTRIES

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: 053-460-2312

TURKEY/CYPRUS

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LB21-128 Jebel Ali Freezone

P.O.Box 17328, Dubai, U.A.E.

Tel: 971-4-881-5868

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 2737-7688

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong,

Youngdungpo-ku, Seoul, Korea

Tel: 02-3770-0661

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-703-0900

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music Asia Pte., Ltd.

11 Ubi Road #06-00, Meiban Industrial Building,

Singapore

Tel: 65-747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

10F, 150, Tun-Hwa Northroad,

Taipei, Taiwan, R.O.C.

Tel: 02-2713-8999

THAILAND

Siam Music Yamaha Co., Ltd.

121/60-61 RS Tower 17th Floor,

Ratchadaphisek RD., Dindaeng,

Bangkok 10320, Thailand

Tel: 02-641-2951

THE PEOPLE’S REPUBLIC OF CHINA

AND OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: 053-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank, Victoria

3006, Australia

Tel: 3-9693-5111

NEW ZEALAND

Music Houses of N.Z. Ltd.

146/148 Captain Springs Road, Te Papapa,

Auckland, New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: 053-460-2312

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: 053-460-3273

[CL] 24

YDP-223

Digital piano

Yamaha Manual Library

http://www2.yamaha.co.jp/manual/english/

M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

V966830 20?AP???.?-01A0 Printed in Indonesia

Yamaha YDP-223 Handleiding

Merk: Yamaha

Model: YDP-223

Categorie: Synthesizer

Type: Handleiding

Deze handleiding is ook geschikt voor

YDP223

Download PDF

rapport

in andere talen

English: Yamaha YDP-223 User manual
italiano: Yamaha YDP-223 Manuale utente
русский: Yamaha YDP-223 Руководство пользователя
français: Yamaha YDP-223 Manuel utilisateur
español: Yamaha YDP-223 Manual de usuario
Deutsch: Yamaha YDP-223 Benutzerhandbuch
português: Yamaha YDP-223 Manual do usuário
dansk: Yamaha YDP-223 Brugermanual
suomi: Yamaha YDP-223 Ohjekirja
čeština: Yamaha YDP-223 Uživatelský manuál
svenska: Yamaha YDP-223 Användarmanual
Türkçe: Yamaha YDP-223 Kullanım kılavuzu
polski: Yamaha YDP-223 Instrukcja obsługi
română: Yamaha YDP-223 Manual de utilizare

Yamaha YDP-223 Handleiding

Deze handleiding is ook geschikt voor

Yamaha YDP-223 Handleiding

in andere talen

Gerelateerde artikelen