Yamaha RX-V496 Handleiding

Merk: Yamaha

Model: RX-V496

Categorie: AV-ontvangers

Type: Handleiding

OWNER’S MANUAL

MODE D’EMPLOI

RX-V496

Natural Sound AV Receiver

Ampli-tuner audio-vidéo

U C A

1/17/0, 3:19 PM

CAUTION

SAFETY INSTRUCTIONS

8 Ventilation – The unit should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the unit should not be situated

on a bed, sofa, rug, or similar surface, that may block the

ventilation openings; or placed in a built-in installation,

such as a bookcase or cabinet that may impede the flow

of air through the ventilation openings.

9 Heat – The unit should be situated away from heat

sources such as radiators, stoves, or other appliances

that produce heat.

10 Power Sources – The unit should be connected to a

power supply only of the type described in the operating

instructions or as marked on the unit.

11 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the unit.

12 Cleaning – The unit should be cleaned only as

recommended by the manufacturer.

13 Nonuse Periods – The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry – Care should be taken so that

objects do not fall into and liquids are not spilled into the

inside of the unit.

15 Damage Requiring Service – The unit should be serviced

by qualified service personnel when:

A. The power-supply cord or the plug has been

damaged; or

B. Objects have fallen, or liquid has been spilled into the

unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or exhibits

a marked change in performance; or

E. The unit has been dropped, or the cabinet damaged.

16 Servicing – The user should not attempt to service the

unit beyond those means described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

17 Power Lines – An outdoor antenna should be located

away from power lines.

18 Grounding or Polarization – Precautions should be taken

so that the grounding or polarization is not defeated.

1 Read Instructions – All the safety and operating

instructions should be read before the unit is operated.

2 Retain Instructions – The safety and operating

instructions should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and other instructions

should be followed.

5 Water and Moisture – The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming

pool, etc.

6 Carts and Stands – The unit should be used only with a

cart or stand that is recommended by the

manufacturer.

6A A unit and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause

the unit and cart combination to overturn.

7 Wall or Ceiling Mounting – The unit should be mounted to

a wall or ceiling only as recommended by the

manufacturer.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert you to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence

of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE.

0101V496caution_EN(UCA) 1/11/0, 10:48 AM2

CAUTION

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

19 For US customers only:

Outdoor Antenna Grounding – If an outside antenna is

connected to this unit, be sure the antenna system is

grounded so as to provide some protection against

voltage surges and built-up static charges. Article 810 of

the National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast

and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to

grounding electrodes, and requirements for the

grounding electrode.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out of

your equipment by playing it at a safe level. One that lets the

sound come through loud and clear without annoying blaring

or distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume

levels.

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC,

to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation instruc-

tions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC Regula-

tions, Part 15 for Class “B” digital devices. Compliance

with these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line filter/

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300

ohm ribbon lead, change the lead-in to coaxial type

cable.

If these corrective measures do not produce satisfac-

tory results, please contact the local retailer autho-

rized to distribute this type of product. If you can not

locate the appropriate retailer, please contact Yamaha

Electronics Corp., U.S.A. 6660 Orangethorpe Ave,

Buena Park, CA 90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

SAFETY INSTRUCTIONS

0101V496caution_EN(UCA) 1/11/0, 10:48 AM3

CAUTION

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2. Install this unit in a cool, dry, clean place — away

from windows, heat sources, sources of excessive

vibration, dust, moisture and cold. Avoid sources of

humming (transformers, motors). To prevent fire or

electrical shock, do not expose the unit to rain or

water.

3. Never open the cabinet. If something drops into the

unit, contact your dealer.

4. Do not use force on switches, controls or connection

wires. When moving the unit, first disconnect the

power cord and then the wires connected to other

component. Never pull the wires themselves.

5. The openings on the cover assure proper ventilation

of the unit. If these openings are obstructed, the

temperature inside the unit will rise rapidly.

Therefore, avoid placing objects against these

openings, and install the unit in a well-ventilated area

to prevent fire and damage.

6. The voltage used must be the same as that specified

on this unit. Using this unit with a higher voltage than

specified is dangerous and may result in fire or other

accidents. YAMAHA will not be held responsible for

any damage resulting from the use of this unit with a

voltage other than that specified.

7. Digital signals generated by this unit may interfere

with other component such as tuners, receivers and

TVs. Move this unit farther away from such

component if interference is observed.

8. Always set VOLUME to the “m” position before

starting the audio source play. Increase the volume

gradually to an appropriate level after playback has

been started.

9. Do not attempt to clean the unit with chemical

solvents; this might damage the finish. Use a clean,

dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before

concluding that the unit is faulty.

11. When not planning to use this unit for a long period

of time (e.g., a vacation), disconnect the AC power

cord from the wall outlet.

12. To prevent lightning damage, disconnect the AC

power cord and disconnect the antenna cable when

there is an electrical storm.

13. Grounding or polarization — Precautions should be

taken so that the grounding or polarization of the unit

is not defeated.

14. AC outlet — Do not connect audio component to the

AC outlet on the rear panel if that component

requires more power than the outlet is rated to

provide.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off. This state is called the standby

mode. In this state, this unit is designed to consume a

very small quantity of power.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

0101V496caution_EN(UCA) 1/11/0, 10:48 AM4

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

FEATURES

5-Channel Power Amplification

◆ Minimum RMS Output

(0.06% THD, 20 Hz – 20 kHz)

[U.S.A. and Canada models]

Main: 70 W + 70 W (8 Ω)

Center: 70 W (8 Ω)

Rear: 70 W + 70 W (8 Ω)

[Australia model]

Main: 65 W + 65 W (8 Ω)

Center: 65 W (8 Ω)

Rear: 65 W + 65 W (8 Ω)

Multi-mode Digital Sound Field

Processing

◆ Digital Sound Field Processor (DSP)

◆ Dolby Digital Decoder

◆ Dolby Pro Logic Decoder

◆ DTS Decoder

◆ CINEMA DSP: Theater-like Sound Experience by

the Combination of YAMAHA DSP Technology

and Dolby Digital, Dolby Pro Logic or DTS

◆ Automatic Input Balance Control for Dolby Pro

Logic decoding

Sophisticated FM/AM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset Editing)

Other Features

◆ “SET MENU” which Provides You with 11 Items

for Optimizing This Unit for Your Audio/Video

System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other Future

Formats

◆ Video Signal Input/Output Capability

(Including S Video Connections)

◆ 2 Optical/1 Coaxial Digital Signal Input Terminals

◆ SLEEP Timer

◆ Remote Control with Preset Manufacturer Codes

INTRODUCTION

CONTENTS

PREPARATION

SPEAKER SETUP....................................................... 8

CONNECTIONS.......................................................... 9

ADJUSTING THE SPEAKER BALANCE ............ 18

BASIC OPERATION

PLAYING A SOURCE .............................................. 20

DIGITAL SOUND FIELD PROCESSOR (DSP)

EFFECT .................................................................. 24

SOUND FIELD PROGRAM .................................... 25

TUNING ..................................................................... 28

RECORDING A SOURCE ON TAPE, MD OR

VIDEO CASSETTE ............................................... 32

ADVANCED OPERATION

SET MENU................................................................. 33

DELAY TIME AND SPEAKER

OUTPUT LEVELS ................................................. 37

SLEEP TIMER .......................................................... 39

PRESET REMOTE CONTROL .............................. 40

APPENDIX

TROUBLESHOOTING ............................................ 47

SPECIFICATIONS.................................................... 50

GLOSSARY................................................................ 52

INDEX ........................................................................ 53

INTRODUCTION

FEATURES .................................................................. 1

CONTENTS ................................................................. 1

GETTING STARTED ................................................. 2

CONTROLS AND FUNCTIONS ............................... 4

y indicates a tip for your operation.

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued and

pending. “DTS”, “DTS Digital Surround”, are trademarks of

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic” and the

double-D symbol are trademarks of Dolby

Laboratories. Confidential Unpublished Works.

rights reserved.

0102V49601-07_EN(UCA) 1/11/0, 11:20 AM1

GETTING STARTED

Checking the Package Contents

Check that the following items are included in your package.

Remote control Batteries (AAA, R03, UM-4 type) Antenna adapter

(U.S.A. and Canada models only)

Indoor FM antenna Quick reference card

Connection guide

Battery Installation in the Remote

Control

1 Turn the remote control over and slide the

battery compartment cover in the direction of

the arrow.

2 Insert the batteries (AAA, R03 or UM-4 type)

according the polarity markings on the inside

of the battery compartment.

3 Close the battery compartment cover.

Battery Replacement

If the remote control operates only when it is close to the

unit, the batteries are weak. Replace all the batteries with

new ones.

Be sure to replace the batteries within about two minutes.

If it takes longer than two minutes, the codes preset for

the remote control will return to the factory settings.

(Refer to pages 40 to 46 about the remote control.)

Notes

• Use only AAA, R03 or UM-4 batteries for replacement.

• Be sure the battery polarity is correct. (See the illustration inside

the battery compartment.)

• Remove the batteries if the remote control will not be used for an

extended period of time.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

AM loop antenna

0102V49601-07_EN(UCA) 1/12/0, 4:11 PM2

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

Using the Remote Control

The remote control transmits a directional infrared beam. Be

sure to aim the remote control directly at the infrared sensor

during operation. When the sensor is covered or there is a

large object between the remote control and the sensor, the

sensor cannot receive signals. The sensor may not be able to

receive signals properly when it is exposed to direct sunlight

or a strong artificial light (such as a fluorescent or strobe

light). In this case, change the direction of the light or

reposition the unit to avoid direct lighting.

Notes

• Handle the remote control with care.

• Do not spill water, tea or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following

conditions:

– high humidity or temperature such as near a heater, stove or

bath;

– dusty places; or

– extremely low temperature.

GETTING STARTED

Remote control

sensor

Within approximately 6 m

(20 feet)

0102V49601-07_EN(UCA) 1/12/0, 4:11 PM3

–

12 3 4 65

7890qwerty

u i op

6 VOLUME

Turn this control to turn up or down the volume.

7 PHONES jack

Connect the headphones to the PHONES jack. You can

listen to the sound to be output from the main speakers

through the headphones.

When using headphones only, set both SPEAKERS A and B

to the OFF position and press EFFECT to turn off the effect

speakers (center and rear) (so that no DSP program name

appear on the display).

8 SPEAKERS

Set A or B (or both A and B) to the ON position for the main

speaker system (connected to this unit) that you want to use.

Set the button(s) to the OFF position for the main speaker

system that you don’t want to use.

9 PROGRAM selector

Press l or h to select a DSP program when the effect

speakers (center and rear) are turned on. The name of the

selected program appears on the display.

0 EFFECT

Press this button to turn on or off the effect speakers (center

and rear). If you turn them off, all Dolby Digital and DTS

audio signals are directed to the right and left main

speakers. In that case, the output levels of the right and left

speakers may not match.

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Press this switch to turn on the power of this unit or to set

this unit in the standby mode. Before turning the power on,

set VOLUME to the “m” position.

Standby mode

In this mode, this unit consumes a very small quantity of

power to receive infrared-signals from the remote

control.

2 Remote control sensor

This receives signals from the remote control.

3 Display

This shows various information. (Refer to page 6 for

details.)

4 INPUT MODE

Press this button to select the input mode among AUTO,

DTS and ANALOG for the DVD/LD, TV/digital TV and

satellite tuner sources.

5 INPUT SELECTOR

Turn this selector to select the input source (TUNER, CD,

PHONO, V-AUX, VCR, SAT/D-TV, DVD/LD) that you

want to listen to or watch. The arrow for the selected input

source indicator lights up on the display.

0102V49601-07_EN(UCA) 1/20/0, 10:50 AM4

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

q Tone controls

These controls are only effective for the sound from the

main speakers.

a) BASS

Turn this control clockwise to increase or counterclockwise

to decrease the low-frequency response. The “0” position

produces a flat response.

b) TREBLE

Turn this control clockwise to increase or counterclockwise

to decrease the high-frequency response. The “0” position

produces a flat response.

w TAPE/MD MON / EXT. DECODER

Press this button to select a tape or an MD source. The

“TAPE/MD MONITOR” indicator lights up on the display.

When you press the button next, the “TAPE/MD

MONITOR” indicator goes off, “EXT. DECODER” appears

on the display and you can listen to a source connected to

the EXTERNAL DECODER INPUT terminals.

e BALANCE

This control is only effective for the sound from the main

speakers.

Turn the control to adjust the balance of the output volume

from the right and left main speakers to compensate for

sound imbalance caused by the speaker location or listening

room conditions.

r A/B/C/D/E

Press this button to select one of a group (A to E) of preset

stations.

t PRESET/TUNING

When “ z ” appears

This button is used to select a preset station number (1 to 8).

Press h to select a higher and l to select a lower preset

station number.

When “ z ” goes off

This button is used for tuning. Press h to tune in to higher

frequencies, and l to tune in to lower frequencies.

y PRESET/TUNING, EDIT

Press this button to turn on or off “ z ” on the display and

switch the function between for storing a broadcasting

station (preset tuning) and for tuning. This button is also

used to exchange the assignment of two preset stations with

each other.

u FM/AM

Press this button to switch the reception band between FM

and AM.

i MEMORY (MAN’L/AUTO FM)

Press this button to store the broadcasting stations. Hold

down this button for more than three seconds to begin

automatic preset tuning.

o TUNING MODE (AUTO/MAN’L MONO)

Press this button to switch the tuning mode between

automatic and manual. To use the automatic tuning method,

press this button so that the “AUTO” indicator lights up on

the display. To use the manual tuning method, press this

button so that the “AUTO” indicator goes off.

p VIDEO AUX terminals

Connect an auxiliary audio or video input source such as a

camcorder to these terminals. Use INPUT SELECTOR to

select the source connected to these terminals.

CONTROLS AND FUNCTIONS

0102V49601-07_EN(UCA) 1/12/0, 4:11 PM5

Display

6 g and o indicators

“ g ” lights up when the built-in Dolby Digital

decoder is on and the signals of the selected source are

encoded with Dolby Digital. “ o ” lights up when

the built-in Dolby Pro Logic decoder is on.

7 x indicator

“ x ” lights up when the built-in digital sound

field processor is on.

8 MEMORY indicator

This flashes for about five seconds after pressing

MEMORY. During this period, the displayed station can be

stored in the memory.

9 AUTO indicator

This lights up when the unit is in the automatic tuning

mode.

0 STEREO indicator

This lights up when an FM stereo broadcast with sufficient

signal strength is being received.

q Signal-level indicator

This indicates the signal level of the station being received.

If multipath interference is detected, the indication

decreases.

w SLEEP indicator

This lights up while the built-in SLEEP timer is on.

CONTROLS AND FUNCTIONS

1 t indicator

The “t” indicator lights up when the built-in DTS

decoder is turned on.

2 DSP program indicators

The name of the selected DSP program lights up in the

following cases:

• When the tuner is selected as the input source.

• When DSP program No. 2, 3 or the subprogram

“ENHANCED” of No.1 is selected.

3 Multi-information display

This display shows various information: for example the

name of the selected DSP program and the various settings

during adjustment with the SET MENU. The current station

frequency and band (FM or AM) also appear when the tuner

is selected as the input source.

4 Input source indicators

One of the arrows for these indicators lights up depending

on which source is selected.

5 TAPE/MD MONITOR indicator

This lights up when the tape deck or MD recorder, etc. is

selected as the input source by pressing TAPE/MD MON /

EXT. DECODER (or TAPE/MD).

0102V49601-07_EN(UCA) 2/10/0, 11:20 AM6

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

Remote Control

1 Indicator

This flashes in red when pressing a button on the remote

control. If it flashes rapidly several times, press the selected

button again.

2 Component selector buttons

Press one of these buttons which corresponds to the

component you want to control with the remote control.

(The proper code must be set for your component. Refer to

“Setup codes” on page 45.) When the component selector

button has been pressed, the remote control is set to that

component operation mode.

3 POWER

Each time you press this button, the unit switches between

the power on and standby mode.

4 TEST

Press this button to output the test tone for each speaker.

5 A/B/C/D/E, PRESET +/–

These buttons are used to select a preset station.

A/B/C/D/E: To select one of a group (A to E) of preset

stations

PRESET +/–: To select a preset station number (1 to 8)

6 MUTE

Press this button to mute the sound. To cancel mute, press

this button again.

7 VOLUME

These buttons are used to adjust the volume level.

u: To turn up the volume

d: To turn down the volume

8 SLEEP

Press this button to set the SLEEP timer.

9 +/–

These buttons adjust the settings of the SET MENU and

TIME/LEVEL mode.

0 TIME/LEVEL

Press this button to select the items in the TIME/LEVEL

mode.

q Input selector buttons

These buttons select the input source.

CD: To play a CD

TUNER: To listen to an FM or AM broadcast

TAPE/MD: To play a tape or MD

DVD/LD: To play a DVD or LD

SAT/D-TV: To watch a TV or satellite broadcast

VCR: To play a video cassette

PHONO: To play an analog record

V-AUX: To use a camcorder

EXT. DEC.: To play other multi-channel source

w EFFECT

Press this button to turn on or off the effect speakers (center

and rear).

e PRG+, PRG–

Press these buttons to select a DSP program.

r SET MENU

Press this button to select the items in the SET MENU.

CONTROLS AND FUNCTIONS

TV VOLUME

TV INPUT

Press AMP(TUNER).

This section describes basic operation of this unit with the

remote control. First, press AMP(TUNER) on the

component selector. Refer to “PRESET REMOTE

CONTROL” on page 40 for full details.

0102V49601-07_EN(UCA) 1/20/0, 10:50 AM7

SPEAKER SETUP

Speaker Placement

Refer to the following diagram when you place the

speakers.

Speakers to Be Used

This unit is designed to provide the best sound-field quality

with a 5-speaker system, using main speakers, rear speakers

and a center speaker. If you use different brands of speakers

(with different tonal qualities) in your system, the tone of a

moving human voice and other types of sound may not shift

smoothly. We recommend that you use speakers from the

same manufacture or speakers with the same tonal quality.

The main speakers are used for the main source sound plus

the effect sounds. They will probably be the speakers from

your present stereo system. The rear speakers are used for

the effect and surround sounds, and the center speaker is for

the center sounds (dialog, vocals, etc.). If for some reason it

is not practical to use a center speaker, you can do without

it. Best results, however, are obtained with the full system.

The main speakers should be high-performance models and

have enough power-handling capacity to accept the

maximum output of your audio system. The other speakers

do not have to be equal to the main speakers. For precise

sound localization, however, it is ideal to use high-

performance models that can reproduce sounds over the full

range for the center speaker and the rear speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is effective

not only for reinforcing bass frequencies from any or all

channels, but also for reproducing the LFE (low frequency

effect) channel with high fidelity when playing back a

source encoded with Dolby Digital or DTS. The YAMAHA

Active Servo Processing Subwoofer System is ideal for

natural and lively bass reproduction.

Main

speaker (L)

Center speaker

Main speaker (R)

Subwoofer

Rear speaker (L)

Rear speaker (R)

1.8 m

■ Main speakers

Place the right and left main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the TV monitor should be the

same.

■ Rear speakers

Place these speakers behind your listening position, facing

slightly inwards, nearly 1.8 m (approx. 6 feet) above the

floor.

■ Center speaker

Align the front face of the center speaker with the front face

of your TV monitor. Place the speaker as close to the

monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the sound will be heard from the

right and left main speakers. In that case, “CENTER SP” in the

SET MENU is set to the NONE position. (Refer to page 34 for

details.)

■ Subwoofer

The position of the subwoofer is not so critical, because low

bass sounds are not highly directional. But it is better to

place the subwoofer near the main speakers. Turn it slightly

toward the center of the room to reduce the wall reflections.

CAUTION

Some types of speakers interfere with a TV monitor. If

this problem occurs, move the speakers away from the

monitor. If you cannot avoid installing the center speaker

or subwoofer near the TV monitor, use magnetically

shielded speakers.

PREPARATION

0103V49608-19_EN(UCA) 1/11/0, 11:24 AM8

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been

completed.

Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some

components require different connection methods and have different terminal names. Refer to the instructions for each

component to be connected to this unit.

When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect

it to the terminals with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products.

Use RCA-type pin plug cables for connecting audio/video components with the exception described later.

The input and output terminals for pin plugs can be distinguished as follows:

Yellow video signals (composite)

White analog audio signals for the left channel

Red analog audio signals for the right channel

coaxial digital signals

After completing all connections, check them again to make sure they are correct.

MAINS

120 V 60Hz

100W MAX. TOTAL

SWITCHED

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

REAR

(SURROUND)

CENTER

MAIN

––++

–

Connecting an Audio

Component (page 12)

Connecting a Video

Component (page 13)

IMPEDANCE SELECTOR

switch (page 17)

Connecting the

Antenna (page 10)

Connecting to an External

Decoder (page 14)

Connecting Speakers

(page 15)

Connecting the Power

Supply Cords (page 17)

(U.S.A. model)

V V

C C

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM9

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal

strength. However, a properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor

reception quality, an outdoor antenna may improve the quality.

Connect each antenna correctly to the designated terminals.

■ Indoor FM antenna (included)

Firmly insert the connector into the FM ANT terminal. The

indoor FM antenna is only a simple antenna. For reception

with better sound quality, installing the outdoor FM antenna

(commercially available) is recommended.

Note

• Do not connect an outdoor FM antenna and the indoor FM

antenna at the same time.

■ Outdoor FM antenna

You may be unable to obtain good FM radio reception

depending on your local conditions (distance from the

broadcasting station, interposing buildings and

mountains, etc.). Consult your dealer or authorized service

center and be sure to install an antenna that suits your local

conditions.

Install the outdoor FM antenna (commercially available) in

a high place as far away from any roads as possible to avoid

being affected by automobile ignition noise.

CONNECTIONS

Indoor FM

antenna

Antenna adapter (included

for U.S.A. and Canada

models)

Note

Use this adapter to match with

F-type connector.

75-ohm coaxial cable

75-ohm/300-ohm antenna

adapter

300-ohm feeder

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM10

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

■ AM loop antenna (included)

The AM loop antenna can be removed from the stand and

attached to a wall, etc. However, note that the reception

sensitivity may deteriorate if the antenna is attached to a

metal or steel reinforced wall.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

■ Connecting the AM loop antenna

1 Press the tab and unlock the terminal hole.

2 Insert the AM loop antenna lead wires into the

AM ANT and GND terminals.

3 Return the tab to its original position to lock

the lead wires. Lightly pull the lead wires to

confirm a good connection.

4 Attach the loop antenna to the antenna stand.

5 Orient the AM loop antenna so that the best

reception is obtained.

■ Outdoor AM antenna

If you cannot obtain good reception with the AM loop

antenna, connect 5 m to 10 m of vinyl covered wire to the

AM ANT terminal and extend it outdoors from a window.

■ Ground (GND terminal)

For maximum safety and minimum interference, connect

the antenna GND terminal to a good earth ground. A good

earth ground is a metal stake driven into moist earth.

CONNECTIONS

Antenna stand

AM loop antenna

Vinyl covered wire (5 m to 10 m)

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM11

Connecting an Audio Component

■ PHONO terminals

These terminals are used to connect a turntable with an MM

or high-output MC cartridge. If you have a turntable with a

low-output MC cartridge, use an inline boosting transformer

or MC head amplifier when connecting to these terminals.

Connecting the ground (earth) wire of the turntable to the GND

terminal will normally minimize hum, but in some cases, better

results may be obtained with the ground wire disconnected.

CONNECTIONS

Be sure to connect the right channel (R), left channel (L),

input (IN) and output (OUT) properly.

Tape deck or

MD recorder

L R

L R L R

OUTPUT

OUTPUT LINE OUT LINE IN

GND

Turntable

(U.S.A. model)

CD player

Analog signal

Signal flow

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM12

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

Connecting a Video Component

■ Audio signal terminals

Be sure to connect the right channel (R), left channel (L),

input (IN) and output (OUT) properly.

■ Video signal terminals

Be sure to connect the input (IN) and output (OUT)

properly.

■ Digital audio signal terminals

If your DVD/LD player, TV/digital TV or satellite

tuner, etc. has coaxial or optical digital signal output

terminals, they can be connected to this unit’s COAXIAL

and/or OPTICAL digital signal input terminals. To make a

connection between the optical digital signal terminals,

remove the cover from each terminal, and then connect

them by using a commercially available optical fiber cable

that conforms to EIA standards. Other cables might not

function correctly.

When making connections between the digital signal

terminals, you should connect the components to the same-

named analog audio signal terminals of this unit, because a

digital signal cannot be recorded by a tape deck, MD

recorder or VCR connected to this unit.

Notes

• Be sure to attach the covers when the OPTICAL terminals are not

being used in order to protect them from dust.

• If your LD player has a Dolby Digital RF signal output terminal,

be sure to use the RF demodulator (separately purchased).

• No sound will be heard when connecting your LD player’s Dolby

Digital RF signal output terminal directly to this unit’s COAXIAL

DVD/LD digital signal input terminal.

• The input signal from the DVD/LD input terminals is selected in

the following order of priority with the input mode set to AUTO:

COAXIAL terminal → OPTICAL terminal → Analog terminal.

Refer to page 22 for details.

• All digital signal input terminals are applicable to sampling

frequencies of 32 kHz, 44.1 kHz and 48 kHz.

CONNECTIONS

L R

L R V V

ANALOG

AUDIO OUT

AUDIO

OUT

AUDIO

VIDEO

OUT

VIDEO

ANALOG

AUDIO OUT

VIDEO

OUT

VIDEO

OUT

COAXIAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

DVD/LD player TV/digital TV, satellite tuner, cable TV

(U.S.A. model)

VCR

Analog signal

Video signal

Digital signal

(optical)

Digital signal

(coaxial)

Signal flow

TV monitor

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM13

■ S VIDEO terminals

If your VCR, TV monitor or DVD/LD player has “S” (high-

resolution) video terminals, they can be connected to this

unit’s S VIDEO terminals. Connect the VCR’s “S” video

input and output terminals to this unit’s S VIDEO VCR

OUT and IN terminals, respectively. Connect the monitor’s

“S” video input terminal to this unit’s S VIDEO MONITOR

OUT terminal. Connect the DVD/LD player’s “S” video

output terminal to this unit’s S VIDEO DVD/LD terminal.

Otherwise, connect the composite video terminals of your

VCR, TV monitor or DVD/LD player to this unit’s

composite video terminals.

Notes

• Use a special S VIDEO cable (commercially available) for the S

VIDEO connection.

• If video signals are input from both the S VIDEO input and

composite input terminals, the signals will be directed to their

respective output terminals.

■ VIDEO AUX terminals (on the front panel)

These terminals are used to connect any video input source

such as a camcorder to this unit.

Connecting to an External Decoder

This unit has additional 6-channel audio signal input

terminals for connecting an external decoder to this unit.

Connect the 6-channel audio signal output terminals of the

decoder to the EXTERNAL DECODER INPUT terminals

of this unit.

Notes

• When a source connected to these terminals is selected, the digital

sound field processor cannot be used.

• The settings of “CENTER SP”, “REAR SP”, “MAIN SP” and

“BASS OUT” in the SET MENU have no effect on a source

connected to these terminals. The setting of “MAIN LVL” is

effective. (Refer to pages 34 and 35 for details.)

CONNECTIONS

L RV

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

Camcorder

S VIDEO OUT

S VIDEO

OUT

S VIDEO IN

DVD/LD player

TV Monitor

VCR

S Video signal

Signal flow

L R L R

MAIN

OUT

SURROUND

OUT

CENTER

OUT

SUBWOOFER

OUT

External decoder

(U.S.A. model)

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM14

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

Connecting Speakers

Be sure to connect the right channel (R), left channel (L),

“+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the

polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTIONS

• Use speakers with the specified impedance shown on

the rear panel of this unit.

• Do not let the bare speaker wires touch each other and

do not let them touch any metal part of this unit. This

could damage the unit and/or speakers.

■ Main speaker terminals

One or two speaker systems can be connected to these

terminals. If you use only one speaker system, connect it to

either of the SPEAKERS A or B terminals.

■ Rear speaker terminals

A rear speaker system can be connected to these terminals.

■ Center speaker terminal

A center speaker can be connected to this terminal.

CONNECTIONS

MAINS

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

REAR

(SURROUND)

CENTER

MAIN

––++

–

120 V 60Hz

100W MAX. TOTAL

SWITCHED

Main speakers A

Right Left

Main speakers B

Right Left

(U.S.A. model)

Center speaker Rear speakers

Right Left

Subwoofer connection

If you have a subwoofer with built-

in amplifier, including the

YAMAHA Active Servo Processing

Subwoofer System, connect the

input terminal of the subwoofer

system to the SUBWOOFER

OUTPUT terminal of this unit.

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM15

■ Speaker cables

1 Remove approx. 10 mm (3/8”) of insulation

from each of the speaker cable.

2 Twist the exposed wires of the cable together

to prevent short circuits.

■ Connecting to the MAIN SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side of

each terminal.

3 Tighten the knob to secure the wire.

■ Connecting to the REAR and CENTER SPEAKERS terminals

1 Open the tab.

2 Insert one bare wire into the hole of each

terminal.

3 Return the tab to secure the wire.

Banana plug connections are also possible. Simply insert the

banana plug connector into the corresponding terminal.

CONNECTIONS

10 mm (3/8”)

Red: positive (+)

Black: negative (–)

Red: positive (+)

Black: negative (–)

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM16

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

IMPEDANCE SELECTOR Switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise the unit may be

damaged.

If this unit fails to turn on when STANDBY/ON is pressed, the IMPEDANCE SELECTOR switch may not be fully slide

to either position. If so, slide the switch to either position fully when this unit is in the standby mode.

Select the right or left position according to the impedance of speakers in your system. Be sure to move this switch only

when this unit is in the standby mode.

Connecting the Power Supply Cords

After completing all connections, connect the AC power

cord to an AC power outlet. Disconnect the AC power cord

if you will not use this unit for a long period of time.

■ AC OUTLETS (SWITCHED)

U.S.A. and Canada models .............................. 2 OUTLETS

Australia model .................................................. 1 OUTLET

Use these outlets to connect the power cords from your

components to this unit. The power to the AC OUTLET(S)

is controlled by this unit’s STANDBY/ON (or POWER).

These outlets will supply power to any connected

component whenever this unit is turned on. The maximum

power (total power consumption of components) that can be

connected to the AC OUTLET(S) is 100 W.

If you use left position right position

Center

speaker

The impedance must be 6 Ω

or higher.

The impedance must be 8 Ω

or higher.

Rear

speakers

The impedance of each

speaker must be 6 Ω or

higher.

The impedance of each

speaker must be 8 Ω or

higher.

If you use two pairs of main

speakers, the impedance of

each speaker must be 8 Ω or

higher.

If you use two pairs of main

speakers, the impedance of

each speaker must be 16 Ω or

higher.

[Canada model only]

The impedance of each

speaker must be 8 Ω or

higher.

Main

speakers

If you use one pair of main

speakers, the impedance of

each speaker must be 4 Ω or

higher.

If you use one pair of main

speakers, the impedance of

each speaker must be 8 Ω or

higher.

CONNECTIONS

(U.S.A. model)

MAINS

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

120 V 60Hz

100W MAX. TOTAL

SWITCHED

(U.S.A. model)

To AC outlet

MAINS

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

120 V 60Hz

100W MAX. TOTAL

SWITCHED

IMPEDANCE

SELECTOR

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM17

Using the Test Tone

The adjustment of each speaker sound output level should

be performed at your listening position with the remote

control. After completing the adjustments, use VOLUME

(u/d) at your listening position to check if the adjustments

are satisfactory.

1 Press AMP(TUNER) on the

component selector.

2 Press TEST.

“TEST LEFT” appears on the display.

3 Turn up the volume.

You will hear a test tone (like pink noise) from each

speaker for about two seconds in following order: left

main speaker, center speaker, right main speaker, right

rear speaker and left rear speaker. The display changes

as shown below.

Notes

• If the test tone cannot be heard, turn down the volume, set the unit

in the standby mode and check the speaker connections.

• If the test tone cannot be heard from the center speaker, check the

setting of “CENTER SP” in the SET MENU.

This procedure lets you adjust the sound output level

balance between the main, center and rear speakers by using

the built-in test tone generator. When this adjustment is

performed, the sound output level heard at the listening

position will be the same from each speaker. This is

important for the best performance of the digital sound field

processor, the Dolby Pro Logic decoder, Dolby Digital

decoder and DTS decoder.

Before You Start Adjusting

1 Set VOLUME to the “m”

position.

2 Turn the power on.

3 Press SPEAKERS A or B

to select the main

speakers to be used.

If you use two main speaker

systems, press both A and B.

4 Set BASS, TREBLE and BALANCE to the “0”

position.

ADJUSTING THE SPEAKER BALANCE

–+–+

2,7

TEST

LEFT

TEST

RIGHT

TEST L SUR. TEST R SUR.

TEST CENTER

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM18

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

4 Adjust BALANCE on the

front panel so that the

sound output level of the

right main speaker and the

left main speaker is the

same.

5 Press TIME/LEVEL

repeatedly to select the

speaker to be adjusted.

“CENTER”, “R SUR.” or

“L SUR.” appears on the

display.

6 Press + to raise and – to

lower the level. Adjust the

sound output levels of the

center speaker and the

rear speakers so that they

become almost the same

as that of the main

speakers.

While adjusting, the test tone is

heard from the selected speaker.

Note

• You cannot adjust the delay time while the test tone is being heard

even if “DELAY” appears on the display.

7 When the adjustment is complete, press TEST.

“TEST OFF” appears on the display and the test tone

stops.

Note

• If “CENTER SP” in the SET MENU is set to the NONE position,

the sound output level of the center speaker cannot be adjusted in

step 6. The center channel sound is automatically output from the

right and left main speakers.

• Once you have completed the adjustments, you can only adjust

the overall volume level of your audio system by using VOLUME

(or VOLUME (u/d)).

• If there is insufficient sound output from the center and rear

speakers, you may decrease the main speaker output level by

setting “MAIN LVL” in the SET MENU to “–10 dB”. (Refer to

page 35 for details.)

ADJUSTING THE SPEAKER BALANCE

Front panel

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM19

When using the remote control, press AMP(TUNER) on

the component selector.

1 Set VOLUME to the “m”

position.

2 Turn the power on.

3 Press SPEAKERS A or B

to select the main

speakers to be used.

If you use two main speaker

systems, press both A and B.

PLAYING A SOURCE

–+–+

1,6

4 Select the desired input

source with INPUT

SELECTOR (or the input

selector buttons). (Turn on

the TV monitor for video

sources.)

The name of the selected input

source appears for a moment

and the arrow for the selected

input source indicator lights up

on the display.

a. To select a tape or an MD source

Press TAPE/MD MON / EXT.

DECODER (or TAPE/MD) so

that the “TAPE/MD

MONITOR” indicator lights up

on the display.

b. To select a source connected to the

EXTERNAL DECODER INPUT terminals

Press TAPE/MD MON / EXT. DECODER repeatedly

(or EXT. DEC.) until “EXT. DECODER” appears on

the display.

Notes

• An audio source can not be played if the “TAPE/MD MONITOR”

indicator lights up or if “EXT. DECODER” appears. Press TAPE/

MD MON / EXT. DECODER twice (or TAPE/MD once) to turn

off the “TAPE/MD MONITOR” indicator. Press TAPE/MD

MON / EXT. DECODER once (or EXT. DEC.) to turn off “EXT.

DECODER”.

• If you select and play a video source when the “TAPE/MD

MONITOR” indicator lights up or “EXT. DECODER” appears,

the play back result will be a video image from the video source

and the sound from the audio source selected by using TAPE/MD

MON / EXT. DECODER (or TAPE/MD or EXT. DEC.).

For the DVD/LD, TV/digital TV and satellite tuner sources, the

current input mode is also shown. Refer to page 22 for details about

the input mode.

Front panel

Remote control

Front panel

Input source

BASIC OPERATION

Front panel Remote control

0104V49620-24_EN(UCA) 1/12/0, 4:13 PM20

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

5 Play the source.

Refer to the instructions for the source component (and

page 28 for details about tuning).

Note

• When controlling an audio/video component (tape deck, MD

recorder, CD player, DVD/LD player, etc.) with the remote

control, press one of the component selector buttons, (TAPE/MD,

CD, DVD/LD, etc.), which corresponds to the component you

want to control. Refer to “PRESET REMOTE CONTROL” on

page 40.

6 Adjust the volume to the desired output level.

If desired, adjust BASS, TREBLE, BALANCE, etc.

These controls are only effective for the sound from the

main speakers.

• BASS controls the low-frequency response.

• TREBLE controls the high-frequency response.

• BALANCE adjusts the balance of the output volume

from the right and left main speakers.

7 Use the digital sound field processor.

Refer to page 24.

PLAYING A SOURCE

■ To mute the sound

Press MUTE on the remote

control.

To cancel mute, press MUTE.

Note

• During muting, “MUTE ON” appears on the display.

■ When you have finished using this

unit

Press STANDBY/ON (or POWER) to set this unit in the

standby mode.

■ BGV (background video) function

The BGV function allows you to combine a video image

from a video source with a sound from an audio source.

(For example, you can listen to classical music while you

are watching a video.) This function can only be controlled

with the remote control.

Play a video source, and then select an audio source with

the input selector buttons on the remote control. The BGV

function does not work if you select the audio source with

INPUT SELECTOR on the front panel.

Front panel Remote control

–+–+

Front panel

Front panel Remote control

0104V49620-24_EN(UCA) 1/11/0, 10:30 AM21

Input Mode (for the DVD/LD and TV/

digital TV and satellite tuner

sources)

This unit allows you to switch the input mode for sources

that send both digital and analog signals to this unit. The

AUTO, DTS and ANALOG input modes are provided.

When you turn on the power of this unit, the input mode for

the DVD/LD source is always set to AUTO and for TV/

digital TV or satellite tuner source is set according to “SAT

INPUT” in the SET MENU. (Refer to page 36 for details.)

■ AUTO

In this mode, the input signal is selected in the following

order of priority:

1. Digital signal encoded with Dolby Digital or DTS

2. Normal digital signal (PCM)

3. Analog signal (ANALOG)

Note

• If digital signals are input from both the OPTICAL and

COAXIAL terminals, the digital signal from the COAXIAL

terminal is selected.

■ DTS

In this mode, only a digital signal encoded with DTS is

selected, even if other signals are being input at the same

time.

■ ANALOG

In this mode, only an analog signal is selected, even if a

digital signal is being input at the same time. Select this

mode when you want to use an analog signal instead of a

digital signal.

PLAYING A SOURCE

■ Switching the input mode

Press INPUT MODE (or the input selector

button that you have pressed to select the

input source on the remote control) repeatedly

until the desired input mode is shown on the

display.

Notes

• Set the input mode to AUTO to play a DVD/LD source encoded

with Dolby Digital.

• Set the input mode to ANALOG to play a normal 2-channel

source with a Dolby Surround program.

• The sound output may be interrupted for some LD and DVD

players in the following situation: The input mode is set to

AUTO. A search is performed while playing the disc encoded

with Dolby Digital or DTS, and then disc playing is restored. The

sound output is interrupted for a moment because the digital

signal was selected again.

• The input mode cannot be changed for the CD, TUNER, TAPE/

MD, VCR, PHONO and VIDEO AUX sources because only

analog signals are used for these.

• The current input mode appears on the display when the DVD/

LD, TV/digital TV or satellite tuner source is selected or the input

mode is changed.

Front panel Remote control

0104V49620-24_EN(UCA) 1/12/0, 4:13 PM22

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

■ Notes on playing a source

encoded with DTS

• If “DATA ERROR” appears on the display while playing an LD

source encoded with DTS, stop playback and turn the player off

and then on again.

• If the digital output data of the player has been processed in any

way, you may not be able to perform DTS decoding even if you

make a digital connection between this unit and the player.

• If you play an LD source encoded with DTS and set the input

mode to ANALOG, there will be the noise of an unprocessed

DTS signal. When you want to play a DTS source, be sure to

connect the source to the digital input terminal and set the input

mode to AUTO or DTS.

• If you switch the input mode to ANALOG while playing a source

encoded with a DTS signal, this unit reproduces no sound.

• If you play an LD source encoded with DTS and set the input

mode to AUTO, there will be a short noise at first while the unit

recognizes the DTS signal and turns on the DTS decoder. This is

not a malfunction, and can be avoided by setting the input mode

to DTS beforehand. In addition, if you continue to play an LD

encoded with DTS with the input mode setting left to AUTO, this

unit automatically switches to the “DTS-decoding” mode to

prevent noise from being generated during subsequent operation.

(The “t” indicator lights up on the display.) No sound will be

heard if a normal PCM LD is played in this mode. (The “t”

indicator will flash.) To play a normal disk, set the input mode to

AUTO again.

PLAYING A SOURCE

■ Notes on playing an LD source

• Some audio/video component, such as LD player, output different

audio signals through their analog and digital terminals. Change

the input mode as necessary.

• If the input mode is set to AUTO for the LD source, this unit

automatically determines which type of signal the LD source

contains. If this unit detects a Dolby Digital or DTS signal, the

decoder automatically switches to the appropriate setting and

reproduces 5.1 channel sound.

• If the LD player is transmitting signals by a non-normal method,

this unit cannot detect the Dolby Digital or DTS signal. In this

case, the decoder automatically switches to PCM or analog.

• If the LD source does not contain a digital soundtrack, connect

the LD player to the analog terminals and set the input mode to

AUTO or ANALOG.

• While you are operating the LD player, if you switch from the

pause or chapter forwarding function to normal playback, you

may hear the PCM or analog sound an instant before the Dolby

Digital sound is played.

0104V49620-24_EN(UCA) 9/28/0, 4:38 PM23

3 Press PRG+ or PRG–

repeatedly to select the

desired program.

The name of the selected

program appears on the display.

If desired, adjust the delay time and the sound output level of each

speaker. (Refer to pages 37 and 38 for details.)

Notes

• You can select a DSP program for each of the input sources. Once

you select a program, it is linked with the input source selected at

that time. So, when you select the input source next time, the

same program is automatically selected.

• When a monaural source is being played with PRO LOGIC/

Normal or PRO LOGIC/ENHANCED, no sound will be heard

from the main speakers and the rear speakers. Sound can only be

heard from the center speaker. However, if “CENTER SP” in the

SET MENU is set to the NONE position, the center channel

sound is output from the main speakers.

• When a source connected to the EXTERNAL DECODER INPUT

terminals of this unit is selected, the digital sound field processor

cannot be used.

Canceling the Sound Effect (turning

off the effect speakers)

Press EFFECT to cancel

the sound effect and

monitor only the main

sound.

Press EFFECT again to turn the

sound effect back on.

Notes

• If the sound effect is canceled when Dolby Digital or DTS is

decoding, the sounds of all channels are mixed and output from

the main speakers.

• If you turn off the sound effect when Dolby Digital or DTS is

decoding, it may happen that the sound is output faintly or not

output normally, depending on the source. In that case, turn back

on the sound effect.

DIGITAL SOUND FIELD PROCESSOR (DSP) EFFECT

Selecting a DSP Program

You can enhance your listening experience by selecting a

DSP program. Refer to pages 25 to 27 for details about each

program.

■ On the front panel

1 Make sure that the effect speakers (center,

rear, and subwoofer) are turned on.

2 Press PROGRAM h or l

repeatedly to select the

desired program.

The name of the selected

program appears on the display.

■ On the remote control

1 Make sure that the effect speakers (center,

rear, and subwoofer) are turned on.

2 Press AMP(TUNER) on the

component selector.

–+–+

Front panel

Remote control

DSP program name

0104V49620-24_EN(UCA) 1/12/0, 4:13 PM24

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

[4] PRO LOGIC/ENHANCED

( ox)

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 4 channels

• DSP: 1 (surround)

[5] DOLBY DIGITAL/ENHANCED

( gx )

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: 2 (surround L, R)

[6] DTS DIGITAL SUR/ENHANCED

( tx)

• Input source: DTS

• Output channel: 5.1 channels

• DSP: 2 (surround L, R)

This program ideally simulates the multi-

surround speaker systems of the 35 mm-film

movie theater. Dolby Pro Logic decoding,

Dolby Digital decoding or DTS decoding and

digital sound field processing are precisely

performed without altering the original sound

orientation.

The surround effect produced by the sound

field folds around the viewer naturally from

the rear to the right and left and toward the

screen.

SOUND FIELD PROGRAM

This unit incorporates a sophisticated, multi-program digital sound field processor (DSP). This processor allows you to

electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theater-

like experience in your listening room. You can create outstanding audio sound by selecting a suitable DSP program (this

will, of course, depend on what you are listening to).

When you select a CINEMA DSP program, one of the built-in decoders (Dobly Pro Logic, Dolby Digital and DTS) is turned

on according to which type of signals the source being played contains.

The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that

most of these are precise digital re-creations of actual acoustic environments.

■ For movie or audio/video sources (Program No. 1 to No. 5: CINEMA DSP

programs)

No. PROGRAM SUBPROGRAM FEATURES

1 q/DTS

SURROUND

[1] PRO LOGIC/Normal ( o )

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 4 channels

• DSP: —

[2] DOLBY DIGITAL/Normal ( g )

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: —

[3] DTS DIGITAL SUR/Normal ( t )

• Input source: DTS

• Output channel: 5.1 channels

• DSP: —

The built-in Dolby Pro Logic decoder, Dolby

Digital decoder or DTS decoder precisely

reproduces the sound and effect of a source

encoded with Dolby Surround, Dolby Digital

or DTS.

The realization of a highly efficient decoding

process improves cross talk and channel

separation, and makes sound positioning

smoother and more precise.

In this program, the digital sound field

processor is not turned on.

0105V49625-27_EN(UCA) 1/11/0, 10:31 AM25

No. PROGRAM SUBPROGRAM FEATURES

2 MOVIE

THEATER 1

3 MOVIE

THEATER 2

[1] 70 mm SPECTACLE

( ox)

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 3 channels

• DSP: 2 (presence & surround)

[2] DGTL SPECTACLE

( g x )

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

[3] DTS SPECTACLE ( tx )

• Input source: DTS

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

This program creates the extremely wide sound

field of a movie theater. It precisely reproduces

the source sound in detail, giving both the video

and the sound field incredible reality. It is ideal

for any kind of video source encoded with

Dolby Surround, Dolby Digital or DTS

(especially large-scale movie productions).

[1] 70 mm ADVENTURE

( ox )

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 3 channels

• DSP: 2 (presence & surround)

[2] DGTL ADVENTURE

( gx)

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

[3] DTS ADVENTURE ( t x )

• Input source: DTS

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

Ideal for precisely reproducing the sound of the

newest multi-track films. The sound field is

made to be similar to that of the newest movie

theaters, so the reverberations of the sound field

itself are restrained as much as possible. The

data for the sound field of an opera house are

used for the front presence, so the three-

dimensional feeling of the sound field is

emphasized, and dialog is precisely oriented on

the screen. By using the data for the sound field

of a concert hall on the surround sound field,

powerful reverberations are generated. You can

enjoy watching action, adventure movies, etc.

with strong presence.

[4] 70 mm GENERAL ( ox )

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 3 channels

• DSP: 2 (presence & surround)

[5] DGTL GENERAL ( gx )

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

[6] DTS GENERAL ( t x )

• Input source: DTS

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

This program is for reproducing sounds on a

multi-track film, and is characterized by a soft

and extensive sound field. The front presence of

the sound field is relatively narrow. It spatially

spreads all around and toward the screen,

restraining echo effect of conversations without

losing clarity. For the surround sound field, the

harmony of music or chorus sounds beautifully

in a wide space at the rear of the sound field.

[4] 70 mm SCI-FI ( o x )

• Input source: Dolby Surround

2-ch Dolby Digital

• Output channel: 3 channels

• DSP: 2 (presence & surround)

[5] DGTL SCI-FI ( g x )

• Input source: Dolby Digital

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

[6] DTS SCI-FI ( t x )

• Input source: DTS

• Output channel: 5.1 channels

• DSP: 3 (presence & surround L, R)

Clearly reproduces dialog and sound effects in

the latest sound form of science fiction films,

thus creating a broad and expansive cinematic

space amid the silence. You can enjoy science

fiction films in a virtual-space sound field that

includes Dolby Surround, Dolby Digital and

DTS-encoded software employing the most

advanced techniques.

SOUND FIELD PROGRAM

0105V49625-27_EN(UCA) 1/11/0, 10:31 AM26

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

No. PROGRAM FEATURES

4 MONO MOVIE

• Input source: Monaural

• Output channel: 1 channel

• DSP: 1

This program is designed specifically to enhance monaural

sources. Compared to a strictly mono setting, the sound image

is wider and slightly forward of the speaker pair, lending an

immediacy to the overall sound. It is particularly effective for

old mono movie, news broadcasts and dialog.

5 TV SPORTS

• Input source: Audio/Video

• Output channel: 2 to 5.1 channels

• DSP: 2 to 3 (presence & surround)

This program is furnished with a tight sound field in which the

sound will not spread excessively at the front, but the rear

surround produces dynamic sound expansion. It is the most

suitable for sports programs.

■ For Hi-Fi audio sources

No. PROGRAM FEATURES

6 DISCO

• Input source: 2-ch PCM/Analog audio

• Output channel: 2 channels

• DSP: 1

This program simulates the acoustic environment of a disco in

the heart of a lively city. The sound is dense and highly

concentrated.

7 ROCK CONCERT

• Input source: 2-ch PCM/Analog audio

• Output channel: 2 channels

• DSP: 1

This program is ideally suited for rock music. You will

experience a dynamic and lively sound field.

8 CONCERT HALL

• Input source: 2-ch PCM/Analog audio

• Output channel: 2 channels

• DSP: 1

This program creates the expansive ambience of a large concert

hall. It is suited for orchestra and opera music.

CINEMA DSP: Dolby Surround + DSP/Dolby Digital + DSP/DTS + DSP

■ Dolby Pro Logic + 2 digital sound fields

Digital sound fields are created in both the presence and

rear surround zones of the Dolby Pro Logic-decoded sound

field. They create a wide acoustic environment and

emphasize the surround effect in the room, letting you feel

as much presence as if you were watching a movie in a

popular Dolby Stereo theater.

■ Dolby Digital or DTS + 3 digital sound fields

Digital sound fields are created in the presence zone and

independently on the left and right surround zones of the

Dolby Digital-decoded or DTS-decoded sound field. They

create a wide acoustic environment and strong surround

effect in the room without losing high channel separation.

With the wide dynamic range of Dolby Digital or DTS

sound, this sound field combination lets you feel as if you

were watching a movie in the newest Dolby Digital theater

or DTS-installed theater. This is the most ideal home theater

sound at the present time.

SOUND FIELD PROGRAM

0105V49625-27_EN(UCA) 1/11/0, 10:31 AM27

5 Press PRESET/TUNING h once to tune in to a

higher frequency and l once to tune in to a

lower frequency.

Press the button again if the tuning search does not stop

at the desired station.

Note

• If you tune in manually to an FM station, it will be automatically

received in monaural mode to increase the signal quality.

• Use the manual tuning method if the tuning search does not stop

at the desired station (because the signal from the station is weak).

• When tuned in to a station, the frequency of the received station is

shown on the display.

Manual Tuning

1 Use INPUT SELECTOR to

select the tuner as the

input source.

2 Press FM/AM to select the reception band (FM

or AM).

“FM” or “AM” appears on the display.

3 Press TUNING MODE so that the “AUTO”

indicator goes off.

4 Press PRESET/TUNING (EDIT) to turn “ z ” off.

5 Press PRESET/TUNING h or l to tune in to

the desired station.

To continue the tuning search, hold down the button.

TUNING

–+–+

Automatic tuning is effective when station signals are

strong and there is no interference. However, if the signal

from the station you want to select is weak, you must tune

in to it manually (manual tuning).

Automatic Tuning

1 Use INPUT SELECTOR to

select the tuner as the

input source.

2 Press FM/AM to select the reception band (FM

or AM).

“FM” or “AM” appears on the display.

3 Press TUNING MODE so that the “AUTO”

indicator lights up on the display.

4 Press PRESET/TUNING (EDIT) to turn “ z ” off.

Lights up

Goes off

Turn “ z ” off

0106V49628-31_EN(UCA) 1/11/0, 10:31 AM28

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

Automatic Preset Tuning (for FM

stations only)

You can make use of the automatic preset tuning function

for FM stations only. This function enables the unit to

automatically tune in with strong signals and to sequentially

store up to 40 FM stations (5 groups x 8 stations).

1 Press FM/AM to select the FM band.

2 Press TUNING MODE so that the “AUTO”

indicator lights up on the display.

3 Hold down MEMORY for about three seconds.

The preset number, the “MEMORY” and “AUTO”

indicators flash. After about five seconds, automatic

preset tuning begins from the frequency currently

displayed toward the higher frequencies.

Received stations are sequentially stored as A1, A2 ...

A8. If more than 8 stations have been tuned, they are

stored as preset station numbers in other groups (B, C,

D and E) in that order.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost when this unit is set in the standby mode.

If, however, the power cord is disconnected from the AC

power outlet or the power is cut for more than one week,

the memory will be erased. If so, store the stations again

by using preset tuning methods.

–+–+

21 3

■ Automatic preset tuning options

You can select the preset number from which the unit will

store FM stations and/or begin tuning toward lower

frequencies. Before automatic preset tuning begins (after

pressing MEMORY in step 3),

1. Press A/B/C/D/E and PRESET/TUNING to select the

preset number with which the first station will be stored.

The automatic preset tuning will stop when stations have

all been stored up to E8.

2. Press PRESET/TUNING (EDIT) to turn “ z ” off and

then press PRESET/TUNING l to begin tuning toward

lower frequencies.

■ When automatic preset tuning is

completed

The display shows the frequency of the last preset station.

Check the contents and the number of preset stations by

following the procedure in the section “To Recall a Preset

Station” on page 30.

Notes

• A new setting can be stored in place of the former one.

• You can manually replace a preset station with another FM or AM

station by simply using the manual preset tuning method.

• Even if the number of received stations is not enough to be stored

up to E8, automatic preset tuning is automatically ended after

searching for all stations.

• Only FM stations with sufficient signal strength are stored by

automatic preset tuning. If the station you want to store is weak in

signal strength, tune in to it manually in monaural mode and store

it by using the manual preset tuning method.

TUNING

Lights up

Flashes

0106V49628-31_EN(UCA) 1/20/0, 10:56 AM29

TUNING

To Recall a Preset Station

You can recall any desired station simply by selecting the

preset station number with which it was stored.

You can also recall a preset station with the remote control.

Press AMP(TUNER) on the component selector and press

TUNER on the input selector.

1 Press A/B/C/D/E to select the required group

of preset stations.

Make sure that “ z ” appears on the display.

2 Press PRESET/TUNING h or l (or PRESET

+/–) to select a preset station number (1 to 8).

The preset group and number appear on the display

along with the reception band, frequency and signal

strength information.

–+–+

1 2

Flashes

Front panel

Remote control

Front panel

Remote control

–+–+

3 2,54

Manual Preset Tuning

You can also store up to 40 stations (5 groups x 8 stations)

manually.

1 Tune in to the desired station.

Refer to page 28 for the tuning procedure.

2 Press MEMORY.

The “MEMORY” indicator flashes for about five

seconds.

3 Press A/B/C/D/E repeatedly to select the

desired group (A to E) of preset stations

before the “MEMORY” indicator goes off.

Make sure that “ z ” appears on the display. The

selected group appears on the display.

4 Press PRESET/TUNING h or l to select a

preset station number (1 to 8) with which you

want to store the station before the “MEMORY”

indicator goes off.

Press h to select a higher

preset station number and l to

select a lower preset station

number.

5 Press MEMORY before the “MEMORY”

indicator goes off.

The displayed station has been stored as the preset

group and number you have selected, and the reception

band and frequency appear on the display.

6 Repeat steps 1 to 5 to store other stations.

Notes

• A new setting can be stored in place of the former one.

• The reception mode (stereo or monaural) is stored along with the

station frequency.

0106V49628-31_EN(UCA) 1/12/0, 4:14 PM30

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

–+–+

2,4

Exchanging Preset Stations

You can exchange the assignment of two preset stations

with each other.

■ Example: If you want to exchange

preset station “E1” with “A5”.

1 Recall preset station “E1”.

Refer to the procedure in the section “To Recall a

Preset Station” on page 30.

2 Hold down (PRESET/TUNING) EDIT for about

three second.

“E1” and the “MEMORY” indicator flash.

3 Recall preset station “A5” by using the buttons

on the front panel.

“A5” and the “MEMORY”

indicator flash.

4 Press (PRESET/TUNING) EDIT again.

The display shows the exchange of stations has been

completed.

TUNING

Flashes

0106V49628-31_EN(UCA) 1/20/0, 10:56 AM31

RECORDING A SOURCE ON TAPE, MD OR VIDEO CASSETTE

–+–+

1,42

Recording adjustments and other operations are performed

from the tape deck, MD recorder or VCR. Refer to the

instructions for these components.

1 Set VOLUME to the “m”

position.

2 Select the source you want to record.

3 Begin recording by the tape deck, MD recorder

or VCR connected to this unit.

4 Play the source and then turn up the volume to

confirm the input source.

If a tape deck or MD recorder is being used for recording, you can

monitor the sounds being recorded by pressing TAPE/MD MON /

EXT. DECODER (or TAPE/MD).

Notes

• The DSP program and the setting of VOLUME, BASS, TREBLE

and BALANCE have no effect on the material being recorded.

• Composite video and S video signals pass independently through

this unit’s video circuits. Therefore, when recording or dubbing

video signals, if your video source component is connected to

provide only an S video (or only a composite video) signal, you

can record only an S video (or only a composite video) signal by

your VCR.

• A source connected to this unit only through the digital terminals

cannot be recorded by the tape deck, MD recorder or VCR

connected to this unit.

• A source connected to the EXTERNAL DECODER INPUT

terminals of this unit cannot be recorded.

• Check the copyright laws in your country to record from records,

CDs, radio, etc. Recording of copyrighted material may infringe

If you play back a video source that uses scrambled or

encoded signals to prevent it from being dubbed, the

picture itself may be disturbed due to those signals.

Remote controlFront panel

Front panel

Remote control

0107V49632_EN(UCA) 1/11/0, 10:34 AM32

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

SET MENU

This unit provides you with the following items in the SET

MENU to maximize the performance of your system and

expand your enjoyment for audio listening and video

watching.

1. CENTER SP

2. REAR SP

3. MAIN SP

4. BASS OUT

5. MAIN LVL

6. D.D. LFE

7. D-RANGE

8. DTS LFE

9. CNTR DELAY

10.MEM. GUARD

11.SAT INPUT

Adjusting Items in the SET MENU

Adjustments should be performed with the remote control

while watching the information on the display.

1 Press AMP(TUNER) on the

component selector.

2 Press SET MENU

repeatedly to select the

item you want to adjust.

The selected item appears on

the display.

3 Press + or – repeatedly to

adjust the setting.

4 Repeat steps 2 and 3 to adjust the setting of

any other item in the same way.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost when this unit is set in the standby mode.

If, however, the power cord is disconnected from the AC

power outlet or the power is cut for more than one week,

the settings of the SET MENU will automatically return

to the preset positions and values. If so, adjust the

settings of the SET MENU again.

ADVANCED OPERATION

0108V49633-39_EN(UCA) 1/11/0, 10:35 AM33

Description of Each Item

1. CENTER SP

Choices: LRG (Large)/SML (Small)/NONE

Preset position: LRG (Large)

LRG (Large)

Select this position if your center speaker is approximately

the same size as the main speakers. In this position, full-

range signals on the center channel are directed to the center

speaker.

SML (Small)

Select this position if you use a center speaker that is

smaller than the main speakers. In this position, low bass

signals (below 90 Hz) on the center channel are distributed

to the SUBWOOFER OUTPUT terminal (or to the right and

left main speakers if “BASS OUT” is set to the MAIN

position).

NONE

Select this position if you do not have a center speaker

(4-speaker system). In this position, full-range signals on

the center channel are directed to the right and left main

speakers.

2. REAR SP

Choices: LARGE/SMALL

Preset position: LARGE

LARGE

Select this position if your rear speakers have high ability

for bass reproduction, or if a subwoofer is connected in

parallel to the rear speaker. In this position, full-range

signals on the rear channels are directed to the rear speakers.

SMALL

Select this position if your rear speakers do not have high

ability for bass reproduction. In this position, low bass

signals (below 90 Hz) on the rear channels are distributed to

the SUBWOOFER OUTPUT terminal (or to the right and

left main speakers if “BASS OUT” is set to the MAIN

position).

3. MAIN SP

Choices: LARGE/SMALL

Preset position: LARGE

LARGE

Select this position if your main speakers have high ability

for bass reproduction. In this position, full-range signals on

the main channels are directed to the right and left main

speakers.

SMALL

Select this position if your main speakers do not have high

ability for bass reproduction. However, if your system does

not include a subwoofer, do not select this position. In this

position, low bass signals (below 90 Hz) on the main

channels are distributed to the SUBWOOFER OUTPUT

terminal if “BASS OUT” is set to the SW or BOTH

position.

4. BASS OUT

Choices: SW/MAIN/BOTH

Preset position: BOTH

Select this position if your system includes a subwoofer. In

this position, signals on the LFE channel and other low bass

signals that are distributed from other channels are directed

to the SUBWOOFER OUTPUT terminal when playing a

source encoded with Dobly Digital or DTS.

Note

• When playing a 2-channel source (tape, MD, CD, video

cassette etc.), select the BOTH position to direct low bass signals

(below 90 Hz) to the SUBWOOFER OUTPUT terminals.

MAIN

Select this position if your system does not include a

subwoofer. In this position, besides full-range signals on the

main channels, signals on the LFE channel and other low

bass signals (below 90 Hz) that are distributed from other

channels are directed to the right and left main speakers.

BOTH

Select this position if your system includes a subwoofer. In

this position, signals on the LFE channel are directed to the

SUBWOOFER OUTPUT terminal. Low bass signals on the

main channels are directed to both the main speakers and

the SUBWOOFER OUTPUT terminal.

SET MENU

0108V49633-39_EN(UCA) 1/11/0, 10:35 AM34

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

7. D-RANGE (Adjusting the dynamic

range)

Choices: MAX/STD (Standard)/MIN

Preset position: MAX

Note

• This adjustment is only effective when Dolby Digital is being

decoded.

“Dynamic range” is the difference between the maximum

level and the minimum level of sounds. Sounds on a movie

originally designed for movie theaters feature a very wide

dynamic range. Dolby Digital technology can modify the

original sound track into a home audio format with this

wide dynamic range unchanged. Powerful sounds of

extremely wide dynamic range are not always suitable for

home use. Depending on the condition of your listening

environment, it may not be possible to increase the sound

output to a level as high as that in a movie theater. However,

at the normal level suitable for listening in your room, the

low-level parts of source sound often cannot be heard well

because they will be lost among noise in your environment.

Dolby Digital technology has also made it possible to

reduce an original sound track’s dynamic range for a home

audio format by “compressing” the sound data.

MAX

In this position, a source encoded with Dolby Digital is

reproduced in the original sound track’s wide dynamic

range to provide you with powerful sounds just like those in

a movie theater. Selecting this position will be even better if

you can listen to a source at a high output level in a room

specially soundproofed for audio/video enjoyment.

STD (Standard)

In this position, a source encoded with Dolby Digital is

reproduced in the “compressed” dynamic range of the

source that is suitable for low-level listening.

MIN

In this position, the dynamic range is more reduced than in

the STD position. Selecting this position will be effective

when you must listen to a source at a low level.

Note

• It may happen that sound is output faintly or not output normally

depending on the source. In that case, select the MAX or STD

position.

5. MAIN LVL

Choices: NORM (Normal)/–10 dB

Preset position: NORM (Normal)

NORM (Normal)

Normally select this position.

–10 dB

Select this position if the sound output from the main

speakers is too loud and cannot be balanced with the sound

output from the center and rear speakers. In this position,

the sound output from the main speakers is attenuated.

Notes

• The setting of “CENTER SP”, “REAR SP”, “MAIN SP” and

“BASS OUT” have no effect on a source connected to the

EXTERNAL DECODER INPUT terminals on the rear of this

unit.

• Once you have adjusted appropriately for “CENTER SP”, “REAR

SP”, “MAIN SP”, “BASS OUT” and “MAIN LVL”, you do not

have to change any settings unless your speaker system is

modified.

6. D.D. LFE (Adjusting the output

level of the LFE channel for Dolby

Digital)

Control range: –20 dB to 0 dB (in 1 dB steps)

Preset value: 0 dB

Note

• This adjustment is only effective when Dolby Digital is being

decoded and the selected source encoded with Dolby Digital

contains LFE signals.

This adjusts the output level of the LFE channel. If the LFE

signals are mixed with signals of other channels and they

are directed to the same speakers, the ratio of the LFE signal

level to the level of the other signals can be adjusted.

SET MENU

0108V49633-39_EN(UCA) 1/11/0, 10:35 AM35

8. DTS LFE (Adjusting the output

level of the LFE channel for DTS)

Control range: –10 dB to +10 dB (in 1 dB steps)

Preset value: 0 dB

Note

• This adjustment is effective only when DTS is being decoded and

the selected source encoded with DTS contains LFE signals.

This adjusts the output level of the LFE channel. If the LFE

signals are mixed with signals of other channels and they

are directed to the same speakers, the ratio of the LFE signal

level to the level of the other signals can be adjusted.

9. CNTR DELAY (Adjusting the delay

of the center sound)

Control range: 0 ms to 5 ms (in 1 ms steps)

Preset value: 0 ms

Note

• This adjustment is only effective when Dolby Digital or DTS is

being decoded and the selected source encoded with Dolby

Digital or DTS contains center channel signals.

This adjusts the delay between the main sound (on the main

channels) and dialog, etc. (on the center channel). The larger

the value, the later the dialog, etc. is generated.

This makes sounds from the left main, center and right main

speakers reach your listening position at the same time. This

is achieved by delaying the sound from the center speaker if

the distance from the center speaker to your listening

position is shorter than the distance from the right and left

main speaker to your listening position.

10.MEM. GUARD (Locking the

settings)

Choices: ON/OFF

Preset position: OFF

If you wish to prevent accidental alterations to the settings

of the SET MENU and other adjustments on this unit, select

the ON position. The following settings on this unit can be

locked:

• Settings of other items in the SET MENU

• Settings in the TIME/LEVEL mode

• Settings when using TEST

11.SAT INPUT (Selecting the initial

input mode for a source connected

to the SAT/D-TV input terminals)

Choices: AUTO/LAST

Preset position: AUTO

The input mode for a source connected to the SAT/D-TV

input terminals of this unit can be automatically set when

the power of this unit is turned on. Refer to page 22 for

details about the input mode.

AUTO

In this position, the input mode is always set to AUTO.

LAST

In this position, the input mode is automatically set to that

selected the last time when the power of this unit was turned

on.

SET MENU

0108V49633-39_EN(UCA) 1/11/0, 10:35 AM36

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

1. PRO LOGIC/Normal 15 to 30 20

DOLBY DIGITAL/Normal 0 to 15 5

DTS DIGITAL SUR/Normal 0 to 15 5

PRO LOGIC/ENHANCED 15 to 30 20

DOLBY DIGITAL/ENHANCED 0 to 15 5

DTS DIGITAL SUR/ENHANCED 0 to 15 5

2. 70 mm SPECTACLE 15 to 30 23

DGTL SPECTACLE 1 to 99 15

DTS SPECTACLE 1 to 99 15

70 mm SCI-FI 15 to 30 20

DGTL SCI-FI 1 to 99 16

DTS SCI-FI 1 to 99 16

3. 70 mm ADVENTURE 15 to 30 20

DGTL ADVENTURE 1 to 99 15

DTS ADVENTURE 1 to 99 15

70 mm GENERAL 15 to 30 20

DGTL GENERAL 1 to 99 15

DTS GENERAL 1 to 99 15

4. MONO MOVIE 1 to 99 49

5. TV SPORTS 1 to 99 9

6. DISCO 1 to 99 40

7. ROCK CONCERT 1 to 99 16

8. CONCERT HALL 1 to 99 44

DELAY TIME AND SPEAKER OUTPUT LEVELS

When using the digital sound field processor with the Dolby

Pro Logic decoder, Dolby Digital decoder or DTS decoder,

you can adjust the delay time between the main sound and

sound effect, and each speaker’s output level as you wish.

Delay Time

You can adjust the time difference between the beginning of

the sound from the main speakers and the beginning of the

sound effect from the rear speakers. The larger the value,

the later the sound effect is generated. The delay time can be

individually adjusted to all DSP programs.

Notes

• Adding too much delay will cause an unnatural effect with some

sources.

• The sound is momentarily interrupted while adjusting the delay

time.

Sound Output Level of the Center,

Right Rear and Left Rear Speakers,

and Subwoofer

If desired, you can adjust the sound output level of each

speaker even if it has already been adjusted in

“ADJUSTING THE SPEAKER BALANCE” on pages 18

and 19.

Notes

• The sound output level of the center speaker cannot be adjusted

when the input signal is analog, PCM audio, or encoded with

Dolby Digital in 2-channel.

• If “CENTER SP” in the SET MENU is set to the NONE position,

the sound output level of the center speaker cannot be adjusted.

This is because the center channel sound is automatically output

from the right and left main speakers.

• Once the sound output level has been adjusted, the level will be

the same for all DSP programs.

Speaker Control range (dB) Preset value

Center –20 to +10 0

Right rear –20 to +10 0

Left rear –20 to +10 0

Subwoofer –20 to 0 0

Program

Control

range (ms)

Preset

value

0108V49633-39_EN(UCA) 1/20/0, 10:57 AM37

Adjusting Method

Adjustments should be performed with the remote control

while watching the information on the display.

1 Press AMP(TUNER) on the

component selector.

2 Press TIME/LEVEL repeatedly to select the

item you want to adjust.

Each time you press TIME/LEVEL, the selected item

changes and appears on the display as below.

Note

• Depending on the setting of the SET MENU, you may not be able

to select all these items.

DELAY TIME AND SPEAKER OUTPUT LEVELS

DELAY

CENTER

R SUR.

L SUR.

SWFR

3 Press + or – to adjust the

delay time or speaker

output levels.

4 Repeat steps 2 and 3 to adjust the settings of

any other item.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost when this unit is set in the standby mode.

If, however, the power cord is disconnected from the AC

power outlet or the power is cut for more than one week,

the latest values for the delay time and the center/rear/

subwoofer output levels that were set will automatically

return to the preset values. If so, adjust the delay time

and output levels again.

0108V49633-39_EN(UCA) 1/11/0, 10:35 AM38

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

SLEEP TIMER

Canceling the Selected SLEEP

Timer

Press SLEEP repeatedly until “SLEEP OFF”

appears on the display.

It will soon disappear and the “SLEEP” indicator will

go off.

Note

• The SLEEP timer can also be canceled by setting the unit in the

standby mode by using POWER on the remote control (or

STANDBY/ON), or by disconnecting the AC power cord from

the AC power outlet.

The SLEEP timer can be used to automatically set this unit

in the standby mode. This timer is useful when you are

going to sleep while enjoying a broadcast or other desired

input source. The SLEEP timer can only be set with the

remote control.

Notes

• First press AMP(TUNER), TAPE/MD, CD or DVD/LD on the

component selector to set the SLEEP timer for this unit.

• The SLEEP timer is effective for the components connected to the

AC OUTLET(S) on the rear panel of this unit.

Setting the SLEEP Timer

1 Play a source you want to enjoy when you are

going to sleep.

2 Press SLEEP repeatedly to

select the desired SLEEP

time.

Each time you press SLEEP, the

SLEEP time will change as

below:

3 The “SLEEP” indicator soon lights up on the

display after the SLEEP timer has been set.

The display returns to the previous indication.

Lights up

Flashes

120 90 60 30

The SLEEP timer is off

(SLEEP OFF).

(This is the state before

SLEEP is pressed.)

0108V49633-39_EN(UCA) 1/12/0, 4:14 PM39

■ Example: To control YAMAHA CD

player

1 Make sure that VOLUME is set to the “m”

position.

2 Press AMP(TUNER) on the

component selector.

3 Turn on the power.

4 Press CD on the input selector.

PRESET REMOTE CONTROL

The provided remote control is factory set to control not only this unit but also most YAMAHA audio components connected

to it.

There are eight component selector buttons. Press one of these buttons which corresponds to the component you want to

control with the remote control. For example, if you press CD on the component selector, the remote control is set to the CD

operation mode, allowing the CD player to be controlled by the buttons on the remote control.

AMP(TUNER)

You can perform the basic operations of this

unit. Refer to page 7.

The code for a YAMAHA CD player is

factory set.

DVD/LD & DVD MENU

An LD player can be controlled in

the DVD/LD mode. A DVD player can be

controlled in the DVD/LD and DVD

MENU modes. The code for a YAMAHA

DVD player is factory set. If the remote

control does not operate your YAMAHA

DVD player, you need to set the code

number “0048”.

TAPE/MD

The code for a YAMAHA tape deck is

factory set. (The code for the YAMAHA

MD recorder can also be set.)

VCR

A VCR can be controlled.

A TV can be controlled.

CBL/SAT

A cable TV or satellite tuner can be

controlled.

Note

• The button functions on the remote control differ depending on the operation mode. Refer to the following pages for details.

Controlling the Components Connected to This Unit

5 Press CD on the

component selector.

6 Press p.

Refer to page 42 for the CD

player operation buttons.

7 Adjust the volume.

If you set the remote control with the manufacturers’

codes listed from page i at the end of this

manual, you can control other brands of components.

Refer to “Setup codes” on page 45 for details.

0109V49640-46_EN(UCA) 1/11/0, 10:35 AM40

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

Description of Each Mode

■ TAPE/MD MODE

Note

• TV VOLUME functions if you have set the code for your TV.

The dark-shaded buttons do not function. Refer to the instructions for details of each component.

PRESET REMOTE CONTROL

DISPLAY (MD)

SLEEP

EFFECT

MUTE

TV VOLUME

VOLUME

POWER

(TAPE) This button turns this unit on if you have set

the code for a YAMAHA tape deck. This button

turns on the tape deck that has a remote control with

a power button if you have set the code for another

manufacturer.

(MD) This button turns this unit on if you have set

the code for the YAMAHA MD recorder.

r REC/PAUSE

This button gives a pause in recording on a tape deck

or MD recorder.

p PLAY

This button plays a tape or an MD.

b DIR A (TAPE)

This button selects the playing direction of deck A.

SKIP– (MD)

This button skips to the previous track.

w REWIND (TAPE)

This button rewinds a tape.

SEARCH (MD)

This button initiates a backward search on the track

that is playing to find the point from which you want

to listen.

Press TAPE/MD.

Input selector buttons

DECK A/B (TAPE)

This button selects deck A or B on a double-cassette

tape deck.

e PAUSE (MD)

This button gives a pause in operation.

a DIR B (TAPE)

This button selects the playing direction of deck B.

SKIP+ (MD)

This button skips to the next track.

s STOP

This button stops operation on a tape deck or MD

recorder.

f FAST FORWARD (TAPE)

This button winds a tape fast forward.

SEARCH (MD)

This button initiates a fast-forward search on the track

that is playing to find the point from which you want to

listen.

0109V49640-46_EN(UCA) 1/11/0, 10:36 AM41

■ CD MODE

Note

• TV VOLUME and TV INPUT function if you have set the code for your TV.

e PAUSE

This button gives a pause in operation. The button

functions as PAUSE/STOP* for operating a

YAMAHA CD player under factory setting.

a SKIP+

This button skips to the beginning of the next

track.

s STOP

This button stops operation. The button functions

as PAUSE/STOP* for operating YAMAHA CD

players.

f SEARCH

This button initiates a fast-forward search on the

track that is playing to find the point from which

you want to listen.

The dark-shaded buttons do not function. Refer to the instructions for details of each component.

PRESET REMOTE CONTROL

PAUSE/STOP function

Press the button once to give a pause in operation and press once more to stop operation.

DISPLAY

SLEEP

EFFECT

MUTE

TV VOLUME

VOLUME

TV INPUT

Press CD.

POWER

This button turns this unit on if you have set the code

for a YAMAHA CD player. This button turns on the CD

player that has a remote control with a power button if

you have set the code for another manufacturer.

p PLAY

This button plays a CD.

b SKIP–

This button skips to the beginning of the previous

track.

w SEARCH

This button initiates a backward search on the track

that is playing to find the point from which you want

to listen.

Input selector buttons

DISC SKIP +/– (for a CD player with CD

changer)

These buttons skip to the next or previous CD.

0109V49640-46_EN(UCA) 1/11/0, 10:36 AM42

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

■ DVD/LD MODE

Note

• TV VOLUME and TV INPUT function if you have set the code for your TV.

■ DVD MENU MODE

Note

• TV VOLUME and TV INPUT function if you have set the code for your TV.

The dark-shaded buttons do not function. Refer to the instructions for details of each component.

PRESET REMOTE CONTROL

CLEAR

TV INPUT

TV VOLUME

VOLUME

RETURN

MENU UP

MUTE

MENU LEFT

MENU DOWN

TITLE

DISC SKIP +/–

INDEX

MENU SELECT

+10

MENU RIGHT

Press DVD MENU.

POWER

This button turns the unit on if you have

set the code for a YAMAHA DVD player.

This button turns on the DVD player that

has a remote control with a power button

if you have set the code for another

manufacturer.

Numeric buttons

EFFECT

TV INPUT

TV VOLUME

VOLUME

SLEEP

MUTE

SKIP –

STOP

DISC SKIP +/–

DISPLAY

PAUSE

PLAY

SKIP +

Press DVD/LD.

POWER

(DVD) This button turns this unit on if

you have set the code for a YAMAHA

DVD player. This button turns on the

DVD player that has a remote control

with a power button if you have set the

code for another manufacturer.

(LD) This button turns this unit on if you

have set the code for a YAMAHA LD

player. This button turns on the LD player

that has a remote control with a

power button if you have set the

code for another manufacturer.

Input selector buttons

0109V49640-46_EN(UCA) 1/11/0, 10:36 AM43

■ VCR MODE

Note

• TV VOLUME, TV INPUT and TV SLEEP function if you have

set the code for your TV.

■ CBL/SAT MODE

Note

• TV VOLUME, TV INPUT and TV SLEEP function if you have

set the code for your TV.

■ TV MODE

Note

• You can control your VCR if you have set the

code for it.

The dark-shaded buttons do not function. Refer to the instructions for details of each component.

PRESET REMOTE CONTROL

VCR REC

Press this button twice to

start recording.

Press VCR.

EFFECT

TV INPUT

TV VOLUME

VOLUME

TV SLEEP

MUTE

VCR STOP

VCR REWIND

VCR CHANNEL +/–

DISPLAY

VCR PAUSE

VCR PLAY

VCR

FAST FORWARD

CHANNEL

ENTER

CHANNEL

VCR POWER

Press CBL/SAT.

+100

TV INPUT

TV VOLUME

VOLUME

TV SLEEP

MUTE

MENU LEFT

MENU UP

MENU DOWN

RECALL

CBL/SAT

CHANNEL +/–

DISPLAY

MENU SELECT

CHANNEL

ENTER

MENU RIGHT

CBL/SAT POWER

CHANNEL

Press TV.

VCR REC

Press this button twice.

EFFECT

TV INPUT

TV VOLUME

VOLUME

TV SLEEP

TV MUTE

VCR STOP

VCR REWIND

TV CHANNEL +/–

DISPLAY

VCR PAUSE

VCR PLAY

VCR

FAST FORWARD

CHANNEL

ENTER

CHANNEL

TV POWER

0109V49640-46_EN(UCA) 1/11/0, 10:36 AM44

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

Advanced Information

■ Setup codes

You can set the code for the manufacturer of your

component after pressing the component selector buttons

other than AMP(TUNER).

1 Turn on your component to be used.

2 Press one of the

component selector

buttons which

corresponds to the

component to be

controlled.

3 Press both VOLUME

buttons (u/d) at the same

time for about four

seconds.

The indicator flashes twice.

4 Use the numeric buttons to

enter the four-digit

manufacturer’s code for

the component to be used.

Make sure that the

indicator flashes twice.

If the indicator does not flash,

repeat step 3 and re-enter the

code.

5 Press POWER (or any other button) on the

remote control to check if you have set the

code correctly.

If your component cannot be

controlled with the remote

control, try setting another code

for the same manufacturer.

Notes

• You can set only one code for one mode.

• In the DVD/LD and DVD MENU modes:

– Be sure to press DVD/LD on the component selector before

entering the code for the DVD/LD player. The code set in the

DVD/LD mode is also simultaneously set in the DVD MENU

mode. You cannot set the code for a DVD player after pressing

DVD MENU on the component selector.

– DVD MENU operations cannot be performed for some DVD

players.

• A second (and third) VCR can be controlled. Refer to “To use a

second (and third) VCR” for details.

• If your component does not respond to any of the codes listed for

the manufacturer, use the original remote control supplied with

your component.

PRESET REMOTE CONTROL

■ To use a second (and third) VCR

You can control a second (and third) VCR in the CBL/SAT

and DVD MENU modes if a cable TV or satellite tuner, or

DVD player is not being used.

Note

• If you want to control a second (and third) VCR in the DVD

MENU mode, you must set the code for an LD player in the

DVD/LD mode.

1 Turn on the VCR to be used.

2 Press CBL/SAT or DVD

MENU on the component

selector.

3 Press both VOLUME

buttons (u/d) at the same

time for about four

seconds.

The indicator flashes twice.

4 Use the numeric buttons to

enter the four-digit code

for the second (and third)

VCR. Make sure that the

indicator flashes twice.

If the indicator does not flash,

repeat step 3 and re-enter the

code.

5 Press POWER (or any other button) on the

remote control to check if you have set the

code correctly.

If the VCR cannot be controlled

with the remote control, try

setting another code for the

same manufacturer.

0109V49640-46_EN(UCA) 1/11/0, 10:36 AM45

■ Returning to the factory-set codes

To return all components to the factory-set codes, follow

these steps.

1 Press one of the

component selector

buttons other than

AMP(TUNER).

2 Press both VOLUME

buttons (u/d) at the same

time for about four

seconds.

The indicator flashes twice.

3 Enter the code number

“9990”.

Make sure that the indicator

flashes twice.

PRESET REMOTE CONTROL

To return each component to the factory-set codes, follow

these steps.

1 Press one of the

component selector

buttons which

corresponds to the

component to be returned

to the factory-set code.

2 Press both VOLUME

buttons (u/d) at the same

time for about four

seconds.

The indicator flashes twice.

3 Enter the code number

“0000”.

Make sure that the indicator

flashes twice.

The following codes are factory set.

Component

selector button

Component

Code

TV TV 0101

CBL/SAT Satellite tuner 0006

VCR VCR 0002

DVD/LD DVD player 0008 (YAMAHA DVD player)

CD CD player 0005 (YAMAHA CD player)

TAPE/MD Tape deck 0004 (YAMAHA Tape deck)

We recommend that you write all the code numbers you

have set on the “Quick Reference Card”.

0109V49640-46_EN(UCA) 1/11/0, 10:36 AM46

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

TROUBLESHOOTING

If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple

measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power

cord and contact your authorized YAMAHA dealer or service center.

■ General

SYMPTOM CAUSE REMEDY

The unit does not work

normally.

No sound and/or no

picture.

The power cord is not connected or the plug is

not completely inserted.

Firmly connect the power cord.

The IMPEDANCE SELECTOR switch on the

rear panel is not fully set to the right or left

position.

Set the switch fully to the right or left position

when the unit is in the standby mode.

The internal microcomputer has been frozen by

an external electric shock (lightning, excessive

static electricity, etc.) or by a power supply with

low voltage.

Set the unit in the standby mode and disconnect

the AC power cord from the AC power outlet.

After about 30 seconds have passed, connect

the power and operate the unit again.

The speaker connections are not secure.

Incorrect input or output cable connections. Connect the cables properly. If the problem

persists, the cables may be defective.

An appropriate input source has not been

selected.

Select an appropriate input source with INPUT

SELECTOR or TAPE/MD MON / EXT.

DECODER (or the input selector buttons).

Secure the connections.

SPEAKERS have not been set properly. Set SPEAKERS corresponding to the speakers

in use to the ON position.

No picture. There is no S VIDEO connection between this

unit and the TV monitor, although S video

signals are being input to this unit.

Connect the monitor’s “S” video input terminal

to this unit’s S VIDEO MONITOR OUT

terminal.

Only the speaker on one

side can be heard.

Incorrect cable connections. Connect the cables properly. If the problem

persists, the cables may be defective.

Incorrect setting of BALANCE. Adjust it to the appropriate position.

No sound from the effect

speakers.

The sound effect is off. Press EFFECT to turn it on.

A Dolby Surround, Dolby Digital or DTS

decoding DSP program is being used with

material not encoded with Dolby Surround,

Dolby Digital or DTS.

Select another DSP program.

No sound from the

center speaker.

The sound output level of the center speaker is

set to minimum.

Raise the level of the center speaker.

“CENTER SP” in the SET MENU is set to the

NONE position.

Select the LRG or SML position.

The sound is muted.

Set VOLUME to the “m” position, press

MUTE to cancel a mute and adjust the volume.

Play a source whose signals this unit can

reproduce.

Digital signals other than PCM audio and the

signals encoded with Dolby Digital or DTS

which this unit cannot reproduce are being input

to this unit by a CD-ROM, etc.

The sound suddenly

goes off.

The protection circuit has been activated

because of a short circuit, etc.

Set the unit in the standby mode and then turn

on to reset the protection circuit.

The SLEEP timer has functioned. Turn on the power, and play the source again.

Refer to

page

APPENDIX

Incorrect DSP program is selected. Select the appropriate program.

The source encoded with Dolby Digital or DTS

does not have a center channel signal.

No sound from the rear

speakers.

The output level of the rear speakers is set to

minimum.

Raise the output level of the rear speakers.

A monaural source is being played with the PRO

LOGIC/Normal or PRO LOGIC/ENHANCED

program.

Select another DSP program suitable for the

monaural source.

—

12, 13

—

25, 26, 27

The unit fails to turn on

when STANDBY/ON is

pressed, or enters in the

standby mode soon after

the power has been

turned on.

—

0110V49647-52_EN(UCA) 1/11/0, 10:37 AM47

SYMPTOM CAUSE REMEDY

Incorrect cable connections. Firmly connect the audio plugs. If the problem

persists, the cables may be defective.

No connection from the turntable to the GND

terminal.

Make the GND connection between the

turntable and this unit.

The volume level cannot

be increased, or the

sound is distorted.

The component connected to the TAPE/MD

OUT (REC) terminals of this unit is in the

standby mode.

Turn on the power to the component.

The sound effect cannot

be recorded.

It is not possible to record the sound effect by a

tape deck or MD recorder connected to the

TAPE/MD OUT (REC) terminals of this unit.

The DVD/LD, TV/digital TV

or satellite tuner source

cannot be recorded by

tape deck, MD recorder

or VCR connected to this

unit.

The DVD/LD player, TV/digital TV or satellite

tuner is connected to the unit only through the

digital terminals.

Make additional connections between the

analog terminals.

Previously preset

stations can no

longer be tuned in.

The unit has been disconnected for a long

period.

Re-store the stations.

Refer to

page

Adjusting this unit by

using SET MENU, TIME/

LEVEL or TEST cannot

be performed.

“MEM. GUARD” in the SET MENU is set to

the ON position.

Set “MEM. GUARD” to the OFF position.

■ Tuner

SYMPTOM CAUSE REMEDY

FM stereo reception

is noisy.

The characteristics of FM stereo broadcasts

may cause this problem when the transmitter is

too far away or the antenna input is poor.

Check the antenna connections.

Try using a high-quality directional FM

antenna.

Use the manual tuning method.

There is distortion,

and clear reception

cannot be obtained

even with a good FM

antenna.

There is multipath interference.

Adjust the antenna position to eliminate

multipath interference.

The desired station

cannot be tuned in

with the automatic

tuning method.

The station is too weak.

Use the manual tuning method.

Use a high-quality directional FM antenna.

The desired station

cannot be tuned in

with the automatic

tuning method.

The signal is weak or the antenna connections

are loose.

Tighten the AM loop antenna connections and

orient it for best reception.

Use the manual tuning method.

Refer to

page

There are continuous

crackling and hissing

noises.

Noises result from lightning, fluorescent lamps,

motors, thermostats and other electrical

equipment.

Use an outdoor antenna and a ground wire. This

will help somewhat, but it is difficult to

eliminate all noise.

A “humming” sound can

be heard.

The volume level is low

while playing a record.

The record is being played on a turntable with an

MC cartridge.

The turntable should be connected to the unit

through the MC head amplifier.

TROUBLESHOOTING

Select the BOTH position.

12, 13

—

The source does not contain low bass signals

(below 90 Hz).

No sound from the

subwoofer.

“BASS OUT” in the SET MENU is set to the

SW or MAIN position when playing a 2-channel

source.

10, 28

11, 28

—

There are buzzing and

whining noises

(especially in the

evening).

A TV set is being used nearby.

Move this unit away from the TV.

—

0110V49647-52_EN(UCA) 1/11/0, 10:37 AM48

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

■ Remote control

This unit is in the standby mode. Turn on the power of the unit.

SYMPTOM CAUSE REMEDY

Refer to

page

The remote control does

not work.

Direct sunlight or lighting (from an inverter

type of fluorescent lamp, etc.) is striking the

remote control sensor of this unit.

Reposition the unit.

The batteries are weak. Replace all batteries with new ones.

The unit or other

component cannot be

controlled.

The component to be controlled has not been

selected.

Press one of the component selector buttons

which corresponds to the component to be

controlled.

The manufacturer’s code has not been set

properly.

Enter the code again.

Try setting another code for the same

manufacturer.

■ Others

SYMPTOM CAUSE REMEDY

Refer to

page

The sound is degraded

when listening with

headphones to a tape

deck or CD player

connected to this unit.

There is noise

interference from digital

or high-frequency

equipment, or the unit.

The unit is too close to the digital or high-

frequency equipment.

Move the unit further away from such

equipment.

■ When playing back a source encoded with DTS

Refer to

page

A loud hissing noise is

heard when playing back

a source encoded with

DTS.

The player which plays back the source is not

connected to a digital audio signal input

terminal of this unit.

The player must be connected to a digital audio

signal input terminal of this unit besides the

analog audio signal terminal connections.

The input mode is set to ANALOG on this unit. Set a proper input mode to turn on the built-in

DTS decoder.

A percussive noise is

heard when playing back

a source encoded with

DTS.

If the input mode is set to AUTO, depending on

some sources, there may be a noise heard while

this unit is identifying the format of the input

signal.

Set the input mode of the currently selected

input source to DTS.

No sound is heard when

playing back a source

encoded with DTS, even

if the input mode is set

to AUTO on this unit.

The built-in DTS decoder does not function

because the player has a digital volume control

and it is set at a position other than

“maximum,” “neutral” or “ineffective.”

Set the player’s digital volume control at the

maximum, neutral or ineffective position.

No sound is heard when

playing back an MD or

DAT on which has been

recorded a source

encoded with DTS.

A source encoded with DTS cannot be recorded

on an MD or DAT.

No sound is heard when

playing back a source

(CD, etc.) even if the

currently selected input

mode is AUTO.

In the AUTO mode, the DTS-decoding mode

cannot be automatically changed to the normal

(PCM) digital signal input mode.

Set the input mode to AUTO again.

Notes

• It is necessary to use a DTS decoder to play back a source encoded with DTS, so the player which plays back the source must be connected

to a digital audio input terminal of this unit in the way described in this manual. If this connection is not made or only a D-to-A converter is

being used without using a DTS decoder, only a loud hissing noise will be heard when you play back the source.

• If you make a search (or skip, etc.) operation while playing back a source encoded with DTS, the “t” indicator goes off. This is because

this unit automatically changes the DTS-decoding mode to the standard (PCM) digital signal input mode to prevent a noise from being

output.

TROUBLESHOOTING

—

0110V49647-52_EN(UCA) 1/11/0, 10:37 AM49

SPECIFICATIONS

AUDIO SECTION

• Minimum RMS Output Power

20 Hz to 20 kHz, 0.06% THD, 8 ohms

Main L/R, Center, Rear L/R ......................................... 70 W*/65 W

1 kHz, 0.09% THD, 8 ohms

Main L/R, Center, Rear L/R ....................................... 80 W*/70 W

• Maximum Output Power (EIAJ)

1 kHz, 10% THD, 8 ohms ........................................................ 100 W

• DIN Standard Output Power

1 kHz, 0.7% THD, 4 ohms ....................................................... 100 W

• IEC Output Power

1 kHz, 0.06% THD, 8 ohms ....................................................... 70 W

• Dynamic Power (IHF)

8/6/4/2 ohms .................... 100/120/140/160 W*, 90/110/130/150 W

• Damping Factor

20 Hz to 20 kHz, 8 ohms ................................................................ 60

• Frequency Response

CD etc. to MAIN L/R ................................ 20 Hz to 20 kHz, ±0.5 dB

• Total Harmonic Distortion (20 Hz to 20 kHz)

CD etc. to MAIN L/R, 1/2 power, 8 ohms ............................ 0.025%

• Signal-to-Noise Ratio (IHF-A Network)

CD etc. to MAIN L/R

(150 mV, Input Shorted) ........................................................ 96 dB

(250 mV, Input Shorted) .......................................................100 dB

• Residual Noise (IHF-A Network)

MAIN L/R .............................................................................. 150 µV

• Input Sensitivity/Impedance

CD etc. ................................................................. 150 mV/47 k-ohms

EXT. DECODER......................................... 150 mV/40 – 47 k-ohms

• Output Level/Impedance

REC OUT ........................................................... 150 mV/1.2 k-ohms

SUBWOOFER ....................................................... 4.0 V/1.2 k-ohms

PHONES ................................................................. 0.47 V/390 ohms

• Channel Separation (Vol. –30 dB)

CD etc. (Input 5.1 k-ohms Terminated, 1 kHz/10 kHz)

..................................................................................... 60 dB/45 dB

• Tone Control Characteristics

BASS: Boost/cut ..........................................................±10 dB/50 Hz

TREBLE: Boost/cut ................................................... ±10 dB/20 kHz

* for U.S.A. and Canada models

VIDEO SECTION

• Video Signal Type ........................................................... NTSC or PAL

• Video Signal Level ...................................................... 1 Vp-p/75 ohms

• Signal-to-Noise Ratio .................................................................. 50 dB

• Monitor Out Frequency Response....................5 Hz to 10 MHz, –3 dB

FM SECTION

• Tuning Range .................................... 87.5/87.50 to 107.9/108.00 MHz

• Usable Sensitivity (DIN)

Mono (S/N 26 dB) ................................................................... 0.9 µV

Stereo (S/N 46 dB) ................................................................... 28 µV

• Selectivity (two signals, 40 kHz Dev., ±300 kHz) ...................... 55 dB

• Signal-to-Noise Ratio (Mono/Stereo)

DIN ................................................................................. 75 dB/69 dB

IHF ................................................................................. 81 dB/75 dB

• Harmonic Distortion (1 kHz)

Mono/Stereo ........................................................................ 0.1/0.2%

• Stereo Separation (1 kHz) ........................................................... 48 dB

• Frequency Response ........................................ 20 Hz to 15 kHz, ±1 dB

• Antenna Input ......................................................75 ohms, Unbalanced

AM SECTION

• Tuning Range ............................................530/531 to 1,710/1,611 kHz

• Usable Sensitivity................................................................. 300 µV/m

• Signal-to-Noise Ratio ...................................................................52 dB

• Antenna ........................................................................... Loop antenna

GENERAL

• Power Supply

[U.S.A. and Canada models] .................................. AC 120 V, 60 Hz

[Europe, U.K. and Singapore models] .................... AC 230 V, 50 Hz

[Australia model]..................................................... AC 240 V, 50 Hz

[China model]......................................................... AC 220 V, 50 Hz

[General model].............................AC 110/120/220/240 V, 50/60 Hz

• Power Consumption ...................................................... approx. 220 W

• AC Outlets (100 W max. total)

[U.K. and Australia models] ..................................... 1 (SWITCHED)

[Other models].......................................................... 2 (SWITCHED)

• Dimensions (W x H x D)

.....................435 x 151 x 391 mm (17-1/8’’ x 5-15/16’’ x 15-3/8’’)

• Weight ............................................................................ 10 kg (22 lbs.)

• Accessories ................................................................ AM loop antenna

.......................................................................... Indoor FM antenna

.....................75-ohm/300-ohm antenna adapter (U.K. model only)

........................ Antenna adapter (U.S.A. and Canada models only)

.................................................................................Remote control

........................................................................................... Batteries

Specifications are subject to change without notice.

0110V49647-52_EN(UCA) 9/28/0, 4:38 PM50

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIXINTRODUCTION PREPARATION

CINEMA DSP

GLOSSARY

■ Dolby Surround

Dolby Surround uses four discrete channels and five

speakers to reproduce realistic and dynamic sound effects:

two main channels (left and right), a center channel for

dialog, and a rear channel for special sound effects. The rear

channel reproduces sound within a narrow frequency range.

Most video tapes and laser discs include Dolby Surround

encoding, as do many TV and cable broadcasts. The Dolby

Pro Logic decoder built into this unit employs a digital

signal processing system that stabilizes each channel for

even more accurate sound positioning than is available with

standard analog processors.

■ Dolby Digital

Dolby Digital is a digital surround sound system that

provides completely independent multi-channel audio to

you. Dolby Digital provides five full-range channels in what

is sometimes referred to as a “3/2” configuration: three front

channels (left, center and right), and two surround channels.

A sixth bass-only effect channel is also provided for output

of LFE (low frequency effect), or low bass effects that are

independent of other channels. (This is called the “LFE

channel”.) This channel is counted as 0.1, thus giving rise to

the term 5.1 channels in total.

The wide dynamic range of sound reproduced by the five

full-range channels and precise sound orientation by digital

sound processing provides listeners with excitement and

realism that have never been experienced before.

■ DTS (Digital Theater System)

Digital Surround

DTS was developed to replace analog soundtracks of

movies with six discrete channels of digital soundtracks,

and it is now installed in many theaters around the world.

The DTS digital playback system changed the way we

experienced movies in theaters with six discrete channels of

superb digital audio.

DTS technology, through intense research and development

has made it possible to deliver similar encode/decode

discrete technology to home audio surround-sound

entertainment.

DTS Digital Surround is an encode/decode system which

delivers six channels of master-quality, 20-bit audio;

technically, it is 5.1 channels, which means 5 full-range

(left, center, right and two surround) channels, plus a

subwoofer (LFE) channel (as “0.1”). It is compatible with

the 5.1 speaker configurations that are currently available

for home theater systems.

■ CINEMA DSP

The Dolby Surround and Dolby Digital sound and DTS

systems show their full ability in a large movie theater,

because movie sounds are originally designed to be

reproduced in a large movie theater that uses a multitude of

speakers. Trying to create a sound environment similar to

that of a movie theater in your home is difficult because of

the room size, material inside the walls, the number of

speakers, and so on. In other words, your listening room is

very different from a movie theater.

However, YAMAHA DSP technology allows you to create

nearly the same sound experience as that of a large movie

theater in your home by compensating for the lack of

presence and dynamics in the listening room with original

digital sound fields combined with Dolby Surround, Dolby

Digital or DTS Digital Surround sounds.

The YAMAHA “CINEMA DSP” logo indicates those

programs that are created by the combination of YAMAHA

DSP technology and Dolby Surround, Dolby Digital or

DTS.

■ LFE 0.1 Channel

This channel is for reproduction of low bass signals. The

frequency range for this channel is 20 Hz to 120 Hz. This

channel is called the channel 0.1 because it only reproduces

a low frequency range compared to the full-range from

20 Hz to 20 kHz that is reproduced by the 5 channels in a

Dolby Digital or DTS 5.1 channel system.

■ S VIDEO Signal

The S VIDEO signal is separated and transmitted as the Y

signal which indicates the luminance and the C signal which

indicates the chroma of the video signal (composite signal).

Using the S VIDEO terminal eliminates video signal

transmission loss and allows recording and playback of

even more beautiful images.

0110V49647-52_EN(UCA) 1/11/0, 10:37 AM51

INDEX

Accessories .......................................................................... 2

AC outlet ........................................................................... 17

Antennas ...................................................................... 10, 11

BALANCE ........................................................................ 21

BGV (background video) function .................................... 21

Canceling sound effect ...................................................... 24

CINEMA DSP ............................................................. 27, 51

Connections

Antennas................................................................ 10, 11

Audio components (tape deck/MD recorder, CD player

and turntable) .............................................................. 12

Digital connections...................................................... 13

Speakers ...................................................................... 15

TV monitor .................................................................. 13

Video components (DVD/LD player, VCR and TV/

digital TV, satellite tuner) ............................................ 13

Delay time (TIME/LEVEL mode) .................................... 37

Display................................................................................. 6

Dolby Digital ..................................................................... 51

Dolby Surround ................................................................. 51

DSP program ............................................................ 24 to 27

DTS Digital Surround ....................................................... 51

External decoder ................................................................ 14

Front panel........................................................................... 4

IMPEDANCE SELECTOR switch ................................... 17

Input mode......................................................................... 22

LFE ........................................................................ 35, 36, 51

Muting ............................................................................... 21

Playing ............................................................................... 20

Preset stations

To recall a preset station .............................................. 30

Exchanging preset stations .......................................... 31

Preset tuning

Automatic preset tuning .............................................. 29

Manual preset tuning................................................... 30

Recording .......................................................................... 32

Remote control

Basic operations ............................................................ 7

Batteries......................................................................... 2

Component selector................................................. 7, 40

Factory-set code .......................................................... 46

Manufacturer’s codes .......... i (at the end of this manual)

Setup codes.................................................................. 45

SET MENU ....................................................................... 33

Sleep timer......................................................................... 39

Speaker

Output levels (TIME/LEVEL mode) .......................... 37

Output mode (SET MENU) .................................. 34, 35

Speaker balance (test tone).......................................... 18

Placement ...................................................................... 8

STANDBY/ON.................................................................... 4

Test tone....................................................................... 18, 19

Tone controls ..................................................................... 21

Tuning

Automatic tuning......................................................... 28

Manual tuning ............................................................. 28

0110V49647-52_EN(UCA) 1/11/0, 10:37 AM52

A-Mark 1161

A Tandy 0941

Abex 1151

Admira 1141

Adventura 1131

Aiko 1121

Akai 0331, 1101, 1111

Alba 0431

Alleron 1091

Ambassador 1081

Amstrad 0481, 1081

Anam 0251, 1041, 1051,

1061, 1071

Anam National 1041

AOC 0361, 1021, 1031,

1111, 1161

Archer 1161

Audiosonic 1001

Audiovox 1051, 1161

Awai 1481

Bauer 0441

Baur 1001

Beijing 1511, 1551, 1561

Belcor 1031

Bell & Howell 0981, 0991

Beon 1001

Bradford 1051

Brockwood 1031

Broksonic 1161

Bush 1001

Candle 0351, 0361, 0961,

0971, 1111, 1131

Capehart 1021

Carver 0101

Cathay 1001

Celebrity 0951

Centurion 0411

Changhong 1541, 1551, 1561,

1621

Citizen 0351, 0361, 0921,

0931, 0941, 0961,

0971, 1111, 1121,

1131

Clairtone 1011

Clarivox 1001

Concerto 0351, 0971

Conrowa 1751

Contec 0901, 0911, 1011,

1051

Corando 0941

Craig 0251, 1051

Crown 0941, 1051

Curtis Mathes 0161, 0361, 0931,

0941, 0981, 1111

CXC 1051

Daewoo 0291, 0301, 0331,

0721, 0941, 1001,

1031, 1121, 1191,

1531, 1581, 1591,

1601

Dansai 1001

Daytron 0941, 1031

Decca 0271, 1001

Dixi 0331, 1001, 1071

Dumont 0891, 1031

Dynatech 0881

Electroband 0951, 1011

Electrohome 0941

Electron 0941

Elin 1001

Elta 0331

Emerson 0001, 0021, 0061,

0071, 0081, 0091,

0111, 0811, 0821,

0831, 0841, 0851,

0861, 0871, 0901,

0921, 0941, 0981,

1011, 1031, 1051,

1081, 1091

Envision 0361, 1111

Erres 1001

Etron 0331

Ferguson 1001

Finlux 1001

Fisher 0171, 0801, 0981

Formenti 0441

Formonti 1001

Fortress 1141

Fujitsu 1091

Funai 1051, 1091, 1341,

1361, 1411, 1451,

1501, 1521

Futuretech 1051

GE 0131, 0161, 0201,

0751, 0761, 0771,

0781, 0791, 0811,

0861, 1041

GEC 0271, 1001

Gemini 0391

Genexxa 0431

Gibralter 0891, 1031, 1111

GoldStar 0031, 0121, 0351,

0411, 0731, 0741,

0861, 0941, 0971,

1001, 1031, 1111,

1151

Goodmans/Tashiko 0271, 0661,

1001

Granada 1001

Grundig 1781, 1791, 1801,

1811, 1821, 1831,

1841, 1851, 1861,

1871, 1881

Gunpy 1051, 1091

H/K 0721

Hallmark 0861

Hanseatic 1001

Harvard 1051, 1061

Hinari 1001, 1091

Hitachi 0181, 0351, 0671,

0681, 0691, 0701,

0711, 0871, 0941,

0971, 1351

Hypson 1001

Ima 1051

Indiana 1001

Infinity Reference 0101

Interfunk 1001

ITT 0611

Janeil 1131

JBL 0101

JCB 0951

Jensen 0311

Jinxing 1531, 1541, 1551,

1561, 1571, 1621,

1631, 1641, 1651,

1691, 1731

JVC 0261, 0281, 0641,

0651, 0661, 0841

Kawasho 0901

Penny 0161, 0361, 0521,

0531, 0621, 0731,

0751, 0761, 0781,

0791, 0861, 0931,

0941, 1031, 1041,

1111, 1151, 1161

Peony 1561, 1621

Philco 0361, 0581, 0591,

0601, 0611, 0631,

0961, 1031, 1111

Philips 0101, 0401, 1001

Phonola 1001

Pilot 0941, 1031, 1111

Pioneer 0511, 0551, 0871,

1331

Portland 0941, 1031, 1121

Priceclub 0931

Prism 0751

Proscan 0761

Protech 1001

Proton 0501, 0861, 0941,

1021, 1161

Pulsar 0891

Pulser 1031

Quasar 0251, 0751, 1041

Quelle 1001

Radio Shack 0541, 0941, 1031,

1051, 1151

Radiola 1001

RCA 0051, 0141, 0151,

0181, 0411, 0491,

0531, 0761, 0771,

0871, 1031

Realistic 0541, 0861, 0941,

0971, 0981, 1031,

1051, 1111, 1151

Rhapsody 1011

R-line 1001

Runco 0891, 1111

Saisho 0331, 1081

Sampo 0361, 0941, 1021,

1111, 1151

Samsung 0331, 0341, 0351,

0361, 0861, 0931,

0941, 0971, 1001,

1031, 1111, 1151,

1461

Samsux 0941

Sanyo 0171, 0231, 0271,

0661, 0801, 0911,

0981, 1231, 1251,

1261

SBR 1001

Schneider 1001

Scimitsu 1031

Scotch 0861

Scott 0831, 0861, 0941,

1031, 1051, 1091

Sears 0101, 0161, 0171,

0351, 0481, 0521,

0621, 0761, 0801,

0861, 0971, 0981,

1091

Shanghai 1561, 1681

Sharp 0461, 0471, 0541,

0661, 0911, 0941,

1141, 1241, 1271

Shogun 1031

Signature 0991, 1771

LIST OF MANUFACTURER’S CODES

LISTES DES CODES FABRICANT

Kaypani 1021

Kenwood 0361, 1031, 1111

Kloss 0631, 0721, 1131

KTV 0921, 0941, 1011,

1051, 1111

Leyco 1001

Liesenk & Tter 1001

Lloytron 0941

Loewe 1001

Logik 0991, 1771

Luxman 0351, 0971

Lxi 0101, 0621, 0761,

0861, 0981

Magnavox 0101, 0341, 0391,

0401, 0411, 0421,

0581, 0591, 0601,

0611, 0631, 0661,

0961, 1111

Majestic 0991

Marantz 0101, 0221, 0361,

1001, 1111

Mark 1001

Matsui 0271, 0331, 1001

Mediator 1001

Megatron 0691, 0861, 1161

MEI 1011

M Electronic 1001

Memorex 0331, 0571, 0861,

0971, 0981, 0991,

1771

Metz 1791, 1831, 1891,

1901, 1911, 1921,

1931, 1941

MGA 0361, 0561, 0571,

0861, 1031, 1111

Midland 0751, 0761, 0891,

0941, 1151

Mitsubishi 0221, 0321, 0561,

0571, 0661, 0861,

1031, 1101, 1381

Montgomery 1091

Motorola 1041, 1141

MTC 0351, 0361, 0881,

0931, 0971, 1011,

1031, 1111

Multitech 0881, 1051

NAD 0551, 0621, 0861

NEC 0241, 0351, 0361,

0661, 0971, 1031,

1111, 1321, 1711

Neckermann 1001

Nei 1001

Nikkai 0271, 0431, 1001,

1151

Nikko 0861, 1111, 1121

Novabeam 0721

NTC 1121

Onwa 1051

Optimus 0551

Optonica 0541, 1141

Orion 0831, 1001

Osaki 0271, 1151

Otto Versand 1001

Panasonic 0101, 0191, 0251,

0751,1041, 1311,

1371, 1431

Panda 1541, 1721

03V496code(UCA) 1/11/0, 1:07 PM1

Simpson 0581, 0961

Solavox 1151

Sonoko 1001

Sontec 1001

Sony 0371, 0451, 0661,

0841, 0951, 1281,

1441

Soundesign 0861, 0961, 1051,

1091

Soundwave 1001

Spectricon 1161

Squareview 0481

SSS 1031, 1051

Star-lite 1051

Suprem 0951

Supre-macy 1131

Surpa 0351, 0971

Sylvania 0101, 0361, 0441,

0581, 0591, 0601,

0611, 0631, 0961,

1111

Symphonic 0481

Sysline 1001

Tandy 0271, 0431, 1141

Tatung 0271, 0881, 1001,

1041, 1161

Tcl 1561, 1631, 1701

Technics 0751

Techwood 0351, 0751, 0971

Teknika 0101, 0351, 0571,

0931, 0941, 0961,

0971, 0991, 1031,

1051, 1091, 1121,

1131, 1771

Teletech 0331

Tera 0501

Thakral 1671

Thorm 1001

TMK 0351, 0861, 0971,

1081

Toshiba 0381, 0521, 0621,

0661, 0931, 0981,

1301

Tosonic 1011

Totevision 0941

Trical 0911

Universal 0781, 0791

Universum 1001

Vector Research 0361, 1111

Vestel 1001

Victor 0651, 1201, 1211,

1221

Video Concept 1101

Vidikron 0101, 0211

Vidtech 0861, 1031

Viking 1131

Wards 0101, 0361, 0451,

0541, 0581, 0591,

0601, 0611, 0771,

0781, 0791, 0861,

0971, 0991, 1031,

1091, 1111, 1771

Watson 1001

Xogego 1611, 1621, 1661,

1741, 1761

Yamaha 0221, 0361, 0571,

1031, 1111, 1141,

1381

Yoko 1001

Zenith 0011, 0041, 0891,

0991, 1771

Zonda 1161

CABLE

ABC 0256, 0376

Antronix 0136

Archer 0136, 0286

BBT 0076

Cabletime 0166

Cablevision 0196

Colour Voice 0306, 0346

Comtronics 0216, 0276

Eagle Comronics 0276

Eastern 0066

Electricord 0206

Electus 0266

GE 0116, 0126

GEC Cable System 0196

Hamlin H5 0676

Hamlin H6 0666

Hamlin H6S 0656

Hamlin H8 0646

Hamlin H9 0636

Jerrold 0256

Jerrold 400L 0626

Jerrold 450L 0616

Jerrold 550 0606

Jerrold Osd Catv 0596

Jerrold Sprucer 0436

Magnavox/Philips 0416, 0426

Mamm 0296

Memorex 0386

Movie Time 0146, 0206

Northcoast 0016

NSC 0146

Oak 0106

Oak Sigma 450 0546

Oak Sigma 550 0536

Panasonic TZ 120/130 0476

Panasonic TZ 170/180 0446

Panasonic TZ140 0466

Panasonic TZ150/160 0456

Paragon 0386

Philips 0036, 0216, 0306,

0316, 0326, 0336,

0346

Pioneer 0006, 0086

Pioneer BR50 0846

Pioneer BR60/70/80/81/82

0696

Pioneer BR90 0556

Pulsar 0386

RCA Digital Satellite System

0396, 0406

Realistic 0136

Regency/Eastern0686

Runco 0386

Samsung 0276

Scientific Atlanta 175/475 0576

Scientific Atlanta 75 0366, 0586

Scientific Atlanta 8650 0566

Signal 0276

SL Marx 0276

Spectavision 0236

Standard Components 0186

Starcom V 0256

Stargate 0276

Sylvania/Texscan 0376, 0496

Teknika 0176

Teleservice 0056

Teleview 0276

Texscan 0186, 0376

TFC 0026

Tocom 0226, 0356

Tocom 5503A 0526

Tocom 5503VIP/5507 0516

Tocom TC56 0506

Toshiba 0386

Tudi 0046

Unika 0136

Universal 0136, 0156, 0206,

0286

Videoway 0096

Viewstar 0216

Zenith 0246, 0386, 0486

SATELLITE TUNER

Alpha Star 0826

Chaparral 0756

Echostar 0836

General Instrument 0776

HTS 0836

Hughes Network Systems 0816

Jerrold 0776, 0786

Panasonic 0806

Primestar 0776, 0786

RCA 0766

Sony 0796

VCR

A Tandy 0902

Adventura 0992

Aiko 0982

Aiwa 0992

Akai 0262, 0942, 0952,

0962, 0972

American High 0932

Amstrad 0992

ASA 0002, 0912

Asha 0922

Audio Dynamics 0202

Audiovox 0912

Beaumark 0922

Bell & Howell 0902

Blaupunkt 0412

Broksonic 0872, 0882, 0892

Bush 0852

Calix 0912

Canon 0862, 0932

CCE 0852, 0982

Citizen 0912, 0982

Colt 0852

Craig 0832, 0842, 0852,

0912, 0922

Curtis Mathes 0662, 0822, 0932

Cybernex 0922

Daewoo 0802, 0812, 0982

DBX 0202

Dynatech 0472, 0992

Electrohome 0912

Electrophonic 0912

Emerex 0792

Emerson 0072, 0132, 0142,

0152, 0162, 0172,

0182, 0192, 0212,

0702, 0712, 0722,

0732, 0742, 0752,

0762, 0772, 0782,

0872, 0882, 0892,

0912, 0952, 0992,

1072

Finlux 0002, 0992

Fisher 0682, 0692, 0842,

0902

Fuji 0672, 0932

Funai 0992

Garrard 0992

GE 0662, 0822, 0932

Go Video 0642, 0652

GoldStar 0082, 0632, 0912

Goodmans 0402

Gradiente 0992

Granda 0612, 0902

Grundig 0002

H/K 1082

Harley Davidson 0992

Harmon/Kardon 0632, 1082

Harwood 0752, 0852

Headquarter 0612

HI-Q 0842

Hinari 0852

Hitachi 0102, 0562, 0572,

0582, 0592, 0602,

0992

ITT 0942

JVC 0202, 0522, 0532,

0542, 0552

Kenwood 0202, 0542, 0612,

0632, 0902

KLH 0852

Kodak 0912, 0932

Lloyd 0992

Logik 0852

Luxor 0942

LXI 0022, 0912

Magnavox 0002, 0482, 0492,

0502, 0512, 0932

Magnin 0922

Marantz 0002, 0202, 0402,

0632, 0932

Marta 0912

Matsui 0722

Matsushita 0932

MEI 0222, 0932

Memorex 0232, 0242, 0472,

0512, 0612, 0842,

0902, 0912, 0922,

0932, 0992

MGA 0762, 0952

MGA Technology 0922

Minolta 0592, 0602

Mitsubishi 0452, 0462, 0542,

0762, 0952, 1082

Motorola 0472, 0932

MTC 0922, 0992

Multitech 0852, 0992

NAD 0442

NEC 0122, 0202, 0292,

0422, 0432, 0542,

0632

Nikko 0912

Noblex 0922

Olympus 0412, 0932

Optimus 0442, 0472, 0912

Optonica 0402

Orion 0212, 0722, 0742,

0772

Osaki 0912

Panasonic 0012, 0052, 0092,

0222, 0372, 0382,

0392, 0412, 0932

Penny 0202, 0432, 0602,

0632, 0692, 0912,

0922, 0932

Pentax 0592, 0602

Perdio 0992

Philco 0002, 0932

Philips 0002, 0282, 0402,

0492, 0932

Pilot 0912

Pioneer 0442, 0542

Proscan 1002, 1012, 1022,

1032, 1042, 1052,

1062

Pulsar 0512

Quarter 0612

Quartz 0272, 0612

Quasar 0382, 0392, 0932

Radio Shack 0912, 0992

Radix 0912

Randex 0912

03V496code(UCA) 1/11/0, 1:07 PM2

iii

RCA 0112, 0382, 0392,

0482, 0592, 0602,

0662, 0822, 0942

Realistic 0402, 0472, 0612,

0682, 0842, 0902,

0912, 0922, 0932,

0992

Ricoh 0352, 0362

Saisho 0212, 0582, 0722,

0732, 0742, 0772

Salora 0612, 0762

Samsung 0212, 0312, 0922,

0962

Sanky 0472, 0512

Sansui 0292, 0542, 0832

Sanyo 0242, 0612, 0842,

0902, 0922

SBR 0002, 0282

Schneider 0852

Scott 0342, 0712, 0762,

0872, 0882, 0892

Sears 0302, 0592, 0602,

0612, 0682, 0692,

0842, 0902, 0912,

0932

Sharp 0402, 0472

Shintom 0852

Shogun 0922

Singer 0852

Sony 0032, 0332, 0352,

0362, 0672, 0792,

0932

STS 0602

Sunpak 0352

Sylvania 0002, 0492, 0502,

0762, 0932, 0992

Symphonic 0992

Tandy 0992

Tashiko 0712, 0992

Teac 0992

Technics 0932

Teknika 0322, 0912, 0932,

0992

Telefunken 0252

TMK 0212, 0732, 0772,

0922

Toshiba 0062, 0302, 0342,

0622, 0682, 0712,

0762

Totevision 0912, 0922

Unitech 0922

Vector Research 0202, 0432, 0632

Victor 0532, 0542, 0552

Video Concepts 0202, 0432, 0632,

0952

Wards 0322, 0402, 0472,

0482, 0602, 0712,

0842, 0852, 0922,

0932, 0992

Yamaha 0202, 0632, 0762

Zenith 0042, 0362, 0512,

0672

DVD PLAYER

Akai 0108

JVC 0168

Onkyo 0128

Panasonic 0048

Philips 0188

Pioneer 0208, 0228

Samsung 0148

Sharp 0068

Sony 0028

Toshiba 0088

Yamaha 0008, 0048

LD PLAYER

Aiwa 0157

Denon 0147

Disco Vision 0017

Funai 0157

Hitachi (E) 0017

Kenwood 0087, 0107

Magnavox 0027

Marantz 0027

Mitsubishi 0137

NAD 0137

Panasonic 0077, 0177

Philips 0027

Pioneer 0037, 0017, 0137

RCA 0167

Realistic 0157

Sharp 0127

Sony 0047, 0057, 0117

Victor 0097

Yamaha 0007, 0067

CD PLAYER

Acoustic Research 1295

ADC 0025, 0065

Adcom 0205, 0255, 1015

ADS 0265

Aiwa 0295, 0945, 1035,

1055

Akai 0175, 0485, 0535

Alpine 1215, 1305

Audio-Technica 0545

BSR 0245, 0655, 0775

California Audio Lab 0055

Capetronic 1205

Carrera 0245

Carver 0285, 1135

Casio 0345

Crown 0185

Curtis Maths 0345

Denon 0275, 0875, 0885

Deual (E) 0505

Dynamic Bass (H) 0555

Emerson 0205, 0325, 1105

Eroica 1275

Fisher 0095, 0555, 0925,

1005

Garrard 0365

Genexxa 0305, 0325, 1105

GoldStar 1225, 1265, 1135,

1335

H/K 0105, 0175, 0465,

0995

Hitachi 0195, 0505, 0205,

0815

Inkel 0115, 0395

JVC 0315

Kenwood 0045, 0095, 0405,

0585, 0725, 0735,

0745, 0755, 0895

Kyocera 0025

Luxman 0075, 0425, 0675,

0705, 0715, 0985

Magnavox 0165, 0215, 0645,

0955

Marantz 0215, 0235, 0375,

0785, 1345

McIntosh 0355, 1085

MCS 0905, 1315

Memorex 0205, 0225, 0235,

0305, 0325, 1105

MGA 0135

Mission 0215

Mitsubishi 0135, 0445

MTC 1255

NAD 0035, 0615, 0685,

0695

Nakamichi 0125, 0435, 0515

NEC 0255, 0905, 0965

Nikko 0545, 1005

Onkyo 0155, 0455, 0495,

0805, 1155

Optimus 0225, 0245, 0555,

0595, 0845, 0855,

0865, 0895, 0935

Panasonic 0055, 0825, 1095,

1125

Penny 0905

Philips 0165, 0215

Pioneer 0305, 0935, 1045

Proton 0215, 1185

Quasar 0055

RCA 0205, 0915, 1115

Realistic 0205, 0225, 0235,

0325, 0555, 0845

Revox 1175

Rotel 0215

Saba Telecommander (E) 0505

SAE 0215

Samsung 1285

Sansui 0215, 0625, 0975,

1025, 1105

Sanyo 0145, 0555, 0635,

0765

Scott 0325, 1105

Sears 0345

Sharp 0235, 0665, 0895,

1065, 1075

Sherwood 0115, 0235, 0395,

0475

Siements Garrard 1245

Signature 0175

Sontec 1165

Sony 0065, 0565, 0865,

1145

Staron 1235

STS 0025

Sylvania 0215

Symphnoic 0335

Tandy 0305

Tangberg 1195

Teac 0235, 0335, 0385,

0525, 0795, 0835,

1355

Technics 0055, 0605, 1095

Techwood 1325

Telefunken (E) 0505

Thomson (E) 0505

Toshiba 0035, 0685

Vector Research 0065, 1135

Victor 0315

Wards 0175

Yamaha 0005, 0015, 0575,

1065

MD RECORDER

Yamaha 0024

TAPE DECK

Aiwa 0094, 0214, 0224

Akai 0184

Carver 0094

Denon 0304

Fisher 0144

Garrard 0194, 0204

JVC 0274, 0284, 0294

Kenwood 0124, 0134, 0154,

0234, 0244, 0264

Magnavox 0094

Marantz 0094, 0344

Mitsubishi 0184

Onkyo 0364, 0374

Optimus 0034, 0064, 0204,

0334

Philips 0094

Pioneer 0034, 0044, 0064

Revox 0354

Sansui 0094, 0344

Sharp 0264

Sherwood 0334

Sony 0054, 0084, 0324

Teac 0194, 0254

Technics 0074, 0314

Victor 0294

Wards 0034

Yamaha 0004, 0014

03V496code(UCA) 1/11/0, 1:07 PM3

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia ID

V502840-2

OWNER’S MANUAL

MODE D’EMPLOI

RX-V496

Natural Sound AV Receiver

Ampli-tuner audio-vidéo

U C A

00RX-V496(UCA)-cv1/4 9/28/0, 4:37 PM1

DISPLAY (MD)

SLEEP

EFFECT

MUTE

TV VOLUME

VOLUME

POWER

REC/PAUSE

PLAY

DIR A (TAPE)

SKIP– (MD)

REWIND (TAPE)

SEARCH (MD)

Input selector

buttons

PAUSE (MD)

DECK A/B (TAPE)

DIR B (TAPE)

SKIP+ (MD)

STOP

FAST FORWARD (TAPE)

SEARCH (MD)

SET

SLEEP

TEST

A/B/C/D/E

EFFECT

PRESET+/–

MUTE

TV VOLUME

VOLUME

PRG+,

PRG–

+/–

POWER

TIME LEVEL

Input selector

buttons

TV INPUT

DISPLAY

SLEEP

EFFECT

MUTE

TV VOLUME

VOLUME

POWER

PLAY

SKIP–

Input selector

buttons

PAUSE

TV INPUT

SKIP+

STOP

Quick Reference Card

AMP(TUNER)

TAPE/MD CD DVD/LD

DISC SKIP+/–

DISPLAY

SLEEP

EFFECT

MUTE

TV VOLUME

VOLUME

POWER

PLAY

SKIP–

Input selector

buttons

PAUSE

TV INPUT

SKIP+

STOP

DISC SKIP+/–

V503030

DISPLAY

TV SLEEP

EFFECT

CHANNEL

ENTER

MUTE

TV VOLUME

VOLUME

VCR

POWER

VCR REC

Press this button twice to start recording.

Appuyer deux fois sur cette touche pour commencer l’enregistrement.

Drücken Sie diese Taste zweimal, um die Aufnahme zu starten.

Tryck två gånger på den här knappen för att börja spela in.

VCR PLAY

VCR

REWIND

CHANNEL CHANNEL

VCR

PAUSE

TV INPUT

VCR STOP

VCR FAST

FORWARD

RETURN

TITLE

CLEAR

INDEX

+10

MUTE

TV VOLUME

VOLUME

DISC SKIP+/–

VCR

CHANNEL+/–

CBL/SAT

CHANNEL+/–

POWER

Numeric buttons

TV INPUT

DISPLAY

TV SLEEP

+100

MUTE

TV VOLUME

VOLUME

CBL/SAT

POWER

MENU SELECT

MENU LEFT

RECALL

MENU UP

TV INPUT

MENU RIGHT

MENU DOWN

Quick Reference Card

DVD MENU

VCR CBL/SAT TV

DISPLAY

TV SLEEP

EFFECT

TV MUTE

TV VOLUME

VOLUME

POWER

VCR PLAY

VCR

REWIND

CHANNEL

VCR

PAUSE

TV INPUT

VCR STOP

VCR FAST

FORWARD

MENU SELECT

MENU LEFT

MENU RIGHT

MENU DOWN

MENU UP

CHANNEL

ENTER

CHANNEL+/–

CHANNEL

ENTER

V503030

VCR REC

Premere due volte questo tasto per iniziare la registrazione.

Presione dos veces este botón para empezar a grabar.

Druk tweemaal op deze toets om met opnemen te beginnen.

Documenttranscriptie

UCA RX-V496 Natural Sound AV Receiver Ampli-tuner audio-vidéo OWNER’S MANUAL MODE D’EMPLOI 40 1/17/0, 3:19 PM SAFETY INSTRUCTIONS 8 Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. 9 Heat – The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. • Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 1 Read Instructions – All the safety and operating instructions should be read before the unit is operated. 2 Retain Instructions – The safety and operating instructions should be retained for future reference. 3 Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to. 4 Follow Instructions – All operating and other instructions should be followed. 5 6 Water and Moisture – The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. Carts and Stands – The unit should be used only with a cart or stand that is recommended by the manufacturer. 6A A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 7 10 Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. 11 Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. 12 Cleaning – The unit should be cleaned only as recommended by the manufacturer. 13 Nonuse Periods – The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. 14 Object and Liquid Entry – Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit. 15 Damage Requiring Service – The unit should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normally or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 16 Servicing – The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. 17 Power Lines – An outdoor antenna should be located away from power lines. 18 Grounding or Polarization – Precautions should be taken so that the grounding or polarization is not defeated. Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. CAUTION 0101V496caution_EN(UCA) 2 1/11/0, 10:48 AM SAFETY INSTRUCTIONS MAST ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) NEC – NATIONAL ELECTRICAL CODE PREPARATION Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. EXAMPLE OF ANTENNA GROUNDING INTRODUCTION 19 For US customers only: Outdoor Antenna Grounding – If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. FCC INFORMATION (for US customers only) Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/ s. In the case of radio or TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. APPENDIX The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. ADVANCED OPERATION This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: BASIC OPERATION 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. We Want You Listening For A Lifetime Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. English YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. CAUTION 0101V496caution_EN(UCA) 3 1/11/0, 10:48 AM CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 12. To prevent lightning damage, disconnect the AC power cord and disconnect the antenna cable when there is an electrical storm. 2. Install this unit in a cool, dry, clean place — away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water. 13. Grounding or polarization — Precautions should be taken so that the grounding or polarization of the unit is not defeated. 3. Never open the cabinet. If something drops into the unit, contact your dealer. 14. AC outlet — Do not connect audio component to the AC outlet on the rear panel if that component requires more power than the outlet is rated to provide. 4. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power cord and then the wires connected to other component. Never pull the wires themselves. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. 5. The openings on the cover assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the unit will rise rapidly. Therefore, avoid placing objects against these openings, and install the unit in a well-ventilated area to prevent fire and damage. IMPORTANT Please record the serial number of this unit in the space below. 6. The voltage used must be the same as that specified on this unit. Using this unit with a higher voltage than specified is dangerous and may result in fire or other accidents. YAMAHA will not be held responsible for any damage resulting from the use of this unit with a voltage other than that specified. 7. Digital signals generated by this unit may interfere with other component such as tuners, receivers and TVs. Move this unit farther away from such component if interference is observed. 8. Always set VOLUME to the “m” position before starting the audio source play. Increase the volume gradually to an appropriate level after playback has been started. 9. Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. FOR CANADIAN CUSTOMERS To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003. 10. Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. 11. When not planning to use this unit for a long period of time (e.g., a vacation), disconnect the AC power cord from the wall outlet. CAUTION 0101V496caution_EN(UCA) 4 1/11/0, 10:48 AM INTRODUCTION FEATURES CONTENTS 5-Channel Power Amplification ◆ ◆ ◆ ◆ ◆ Sophisticated FM/AM Tuner ◆ 40-Station Random Access Preset Tuning ◆ Automatic Preset Tuning ◆ Preset Station Shifting Capability (Preset Editing) PLAYING A SOURCE .............................................. 20 DIGITAL SOUND FIELD PROCESSOR (DSP) EFFECT .................................................................. 24 SOUND FIELD PROGRAM .................................... 25 TUNING ..................................................................... 28 RECORDING A SOURCE ON TAPE, MD OR VIDEO CASSETTE ............................................... 32 ADVANCED OPERATION SET MENU ................................................................. 33 DELAY TIME AND SPEAKER OUTPUT LEVELS ................................................. 37 SLEEP TIMER .......................................................... 39 PRESET REMOTE CONTROL .............................. 40 APPENDIX TROUBLESHOOTING ............................................ 47 SPECIFICATIONS .................................................... 50 GLOSSARY ................................................................ 52 INDEX ........................................................................ 53 y indicates a tip for your operation. English Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992 – 1997 Dolby Laboratories, Inc. All rights reserved. BASIC OPERATION Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issued and pending. “DTS”, “DTS Digital Surround”, are trademarks of Digital Theater Systems, Inc. Copyright 1996 Digital Theater Systems, Inc. All Rights Reserved. 1 0102V49601-07_EN(UCA) 1 1/11/0, 11:20 AM APPENDIX ◆ “SET MENU” which Provides You with 11 Items for Optimizing This Unit for Your Audio/Video System ◆ Test Tone Generator for Easier Speaker Balance Adjustment ◆ 6-Channel External Decoder Input for Other Future Formats ◆ Video Signal Input/Output Capability (Including S Video Connections) ◆ 2 Optical/1 Coaxial Digital Signal Input Terminals ◆ SLEEP Timer ◆ Remote Control with Preset Manufacturer Codes SPEAKER SETUP ....................................................... 8 CONNECTIONS .......................................................... 9 ADJUSTING THE SPEAKER BALANCE ............ 18 ADVANCED OPERATION Other Features PREPARATION BASIC OPERATION Digital Sound Field Processor (DSP) Dolby Digital Decoder Dolby Pro Logic Decoder DTS Decoder CINEMA DSP: Theater-like Sound Experience by the Combination of YAMAHA DSP Technology and Dolby Digital, Dolby Pro Logic or DTS ◆ Automatic Input Balance Control for Dolby Pro Logic decoding FEATURES .................................................................. 1 CONTENTS ................................................................. 1 GETTING STARTED ................................................. 2 CONTROLS AND FUNCTIONS ............................... 4 PREPARATION Multi-mode Digital Sound Field Processing INTRODUCTION INTRODUCTION ◆ Minimum RMS Output (0.06% THD, 20 Hz – 20 kHz) [U.S.A. and Canada models] Main: 70 W + 70 W (8 Ω) Center: 70 W (8 Ω) Rear: 70 W + 70 W (8 Ω) [Australia model] Main: 65 W + 65 W (8 Ω) Center: 65 W (8 Ω) Rear: 65 W + 65 W (8 Ω) GETTING STARTED Checking the Package Contents Check that the following items are included in your package. Remote control Batteries (AAA, R03, UM-4 type) Antenna adapter (U.S.A. and Canada models only) Indoor FM antenna Quick reference card AM loop antenna Connection guide Battery Installation in the Remote Control Battery Replacement If the remote control operates only when it is close to the unit, the batteries are weak. Replace all the batteries with new ones. Be sure to replace the batteries within about two minutes. If it takes longer than two minutes, the codes preset for the remote control will return to the factory settings. (Refer to pages 40 to 46 about the remote control.) 2 1 3 Notes 1 Turn the remote control over and slide the battery compartment cover in the direction of the arrow. 2 Insert the batteries (AAA, R03 or UM-4 type) according the polarity markings on the inside of the battery compartment. 3 Close the battery compartment cover. • Use only AAA, R03 or UM-4 batteries for replacement. • Be sure the battery polarity is correct. (See the illustration inside the battery compartment.) • Remove the batteries if the remote control will not be used for an extended period of time. • If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. 2 0102V49601-07_EN(UCA) 2 1/12/0, 4:11 PM GETTING STARTED Using the Remote Control Within approximately 6 m (20 feet) INTRODUCTION Remote control sensor The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the infrared sensor during operation. When the sensor is covered or there is a large object between the remote control and the sensor, the sensor cannot receive signals. The sensor may not be able to receive signals properly when it is exposed to direct sunlight or a strong artificial light (such as a fluorescent or strobe light). In this case, change the direction of the light or reposition the unit to avoid direct lighting. Notes Handle the remote control with care. Do not spill water, tea or other liquids on the remote control. Do not drop the remote control. Do not leave or store the remote control in the following conditions: – high humidity or temperature such as near a heater, stove or bath; – dusty places; or – extremely low temperature. PREPARATION • • • • BASIC OPERATION ADVANCED OPERATION APPENDIX English 3 0102V49601-07_EN(UCA) 3 1/12/0, 4:11 PM CONTROLS AND FUNCTIONS Front Panel 1 2 3 – 7 8 90 + – q + 4 L 5 6 R w e r t y u i o p 1 STANDBY/ON 6 VOLUME Press this switch to turn on the power of this unit or to set this unit in the standby mode. Before turning the power on, set VOLUME to the “m” position. Turn this control to turn up or down the volume. Standby mode In this mode, this unit consumes a very small quantity of power to receive infrared-signals from the remote control. 2 Remote control sensor 7 PHONES jack Connect the headphones to the PHONES jack. You can listen to the sound to be output from the main speakers through the headphones. When using headphones only, set both SPEAKERS A and B to the OFF position and press EFFECT to turn off the effect speakers (center and rear) (so that no DSP program name appear on the display). This receives signals from the remote control. 8 SPEAKERS 3 Display Set A or B (or both A and B) to the ON position for the main speaker system (connected to this unit) that you want to use. Set the button(s) to the OFF position for the main speaker system that you don’t want to use. This shows various information. (Refer to page 6 for details.) 4 INPUT MODE Press this button to select the input mode among AUTO, DTS and ANALOG for the DVD/LD, TV/digital TV and satellite tuner sources. 5 INPUT SELECTOR Turn this selector to select the input source (TUNER, CD, PHONO, V-AUX, VCR, SAT/D-TV, DVD/LD) that you want to listen to or watch. The arrow for the selected input source indicator lights up on the display. 9 PROGRAM selector Press l or h to select a DSP program when the effect speakers (center and rear) are turned on. The name of the selected program appears on the display. 0 EFFECT Press this button to turn on or off the effect speakers (center and rear). If you turn them off, all Dolby Digital and DTS audio signals are directed to the right and left main speakers. In that case, the output levels of the right and left speakers may not match. 4 0102V49601-07_EN(UCA) 4 1/20/0, 10:50 AM CONTROLS AND FUNCTIONS t PRESET/TUNING These controls are only effective for the sound from the main speakers. a) BASS Turn this control clockwise to increase or counterclockwise to decrease the low-frequency response. The “0” position produces a flat response. b) TREBLE Turn this control clockwise to increase or counterclockwise to decrease the high-frequency response. The “0” position produces a flat response. When “ z ” appears This button is used to select a preset station number (1 to 8). Press h to select a higher and l to select a lower preset station number. When “ z ” goes off This button is used for tuning. Press h to tune in to higher frequencies, and l to tune in to lower frequencies. w TAPE/MD MON / EXT. DECODER Press this button to turn on or off “ z ” on the display and switch the function between for storing a broadcasting station (preset tuning) and for tuning. This button is also used to exchange the assignment of two preset stations with each other. u FM/AM Press this button to switch the reception band between FM and AM. i MEMORY (MAN’L/AUTO FM) e BALANCE r A/B/C/D/E Press this button to select one of a group (A to E) of preset stations. Press this button to store the broadcasting stations. Hold down this button for more than three seconds to begin automatic preset tuning. o TUNING MODE (AUTO/MAN’L MONO) Press this button to switch the tuning mode between automatic and manual. To use the automatic tuning method, press this button so that the “AUTO” indicator lights up on the display. To use the manual tuning method, press this button so that the “AUTO” indicator goes off. BASIC OPERATION This control is only effective for the sound from the main speakers. Turn the control to adjust the balance of the output volume from the right and left main speakers to compensate for sound imbalance caused by the speaker location or listening room conditions. PREPARATION Press this button to select a tape or an MD source. The “TAPE/MD MONITOR” indicator lights up on the display. When you press the button next, the “TAPE/MD MONITOR” indicator goes off, “EXT. DECODER” appears on the display and you can listen to a source connected to the EXTERNAL DECODER INPUT terminals. y PRESET/TUNING, EDIT INTRODUCTION q Tone controls p VIDEO AUX terminals ADVANCED OPERATION Connect an auxiliary audio or video input source such as a camcorder to these terminals. Use INPUT SELECTOR to select the source connected to these terminals. APPENDIX English 5 0102V49601-07_EN(UCA) 5 1/12/0, 4:11 PM CONTROLS AND FUNCTIONS Display 1 t indicator 6 g and o indicators The “t” indicator lights up when the built-in DTS decoder is turned on. “ g ” lights up when the built-in Dolby Digital decoder is on and the signals of the selected source are encoded with Dolby Digital. “ o ” lights up when the built-in Dolby Pro Logic decoder is on. 2 DSP program indicators The name of the selected DSP program lights up in the following cases: • When the tuner is selected as the input source. • When DSP program No. 2, 3 or the subprogram “ENHANCED” of No.1 is selected. 3 Multi-information display This display shows various information: for example the name of the selected DSP program and the various settings during adjustment with the SET MENU. The current station frequency and band (FM or AM) also appear when the tuner is selected as the input source. 4 Input source indicators One of the arrows for these indicators lights up depending on which source is selected. 5 TAPE/MD MONITOR indicator This lights up when the tape deck or MD recorder, etc. is selected as the input source by pressing TAPE/MD MON / EXT. DECODER (or TAPE/MD). 7 x indicator “ x ” lights up when the built-in digital sound field processor is on. 8 MEMORY indicator This flashes for about five seconds after pressing MEMORY. During this period, the displayed station can be stored in the memory. 9 AUTO indicator This lights up when the unit is in the automatic tuning mode. 0 STEREO indicator This lights up when an FM stereo broadcast with sufficient signal strength is being received. q Signal-level indicator This indicates the signal level of the station being received. If multipath interference is detected, the indication decreases. w SLEEP indicator This lights up while the built-in SLEEP timer is on. 6 0102V49601-07_EN(UCA) 6 2/10/0, 11:20 AM CONTROLS AND FUNCTIONS Remote Control 3 POWER Each time you press this button, the unit switches between the power on and standby mode. INTRODUCTION This section describes basic operation of this unit with the remote control. First, press AMP(TUNER) on the component selector. Refer to “PRESET REMOTE CONTROL” on page 40 for full details. 4 TEST Press this button to output the test tone for each speaker. 1 5 A/B/C/D/E, PRESET +/– Press AMP(TUNER). 2 3 These buttons are used to select a preset station. A/B/C/D/E: To select one of a group (A to E) of preset stations PRESET +/–: To select a preset station number (1 to 8) PREPARATION 6 MUTE Press this button to mute the sound. To cancel mute, press this button again. 4 q 7 VOLUME w These buttons are used to adjust the volume level. u: To turn up the volume d: To turn down the volume Press this button to set the SLEEP timer. 6 9 +/– TV VOLUME 7 8 BASIC OPERATION 8 SLEEP 5 These buttons adjust the settings of the SET MENU and TIME/LEVEL mode. 0 TIME/LEVEL TV INPUT 9 Press this button to select the items in the TIME/LEVEL mode. e r 0 1 Indicator ADVANCED OPERATION q Input selector buttons These buttons select the input source. CD: To play a CD TUNER: To listen to an FM or AM broadcast TAPE/MD: To play a tape or MD DVD/LD: To play a DVD or LD SAT/D-TV: To watch a TV or satellite broadcast VCR: To play a video cassette PHONO: To play an analog record V-AUX: To use a camcorder EXT. DEC.: To play other multi-channel source w EFFECT 2 Component selector buttons e PRG+, PRG– Press one of these buttons which corresponds to the component you want to control with the remote control. (The proper code must be set for your component. Refer to “Setup codes” on page 45.) When the component selector button has been pressed, the remote control is set to that component operation mode. Press these buttons to select a DSP program. Press this button to turn on or off the effect speakers (center and rear). r SET MENU English Press this button to select the items in the SET MENU. 7 0102V49601-07_EN(UCA) 7 APPENDIX This flashes in red when pressing a button on the remote control. If it flashes rapidly several times, press the selected button again. 1/20/0, 10:50 AM PREPARATION SPEAKER SETUP Speakers to Be Used This unit is designed to provide the best sound-field quality with a 5-speaker system, using main speakers, rear speakers and a center speaker. If you use different brands of speakers (with different tonal qualities) in your system, the tone of a moving human voice and other types of sound may not shift smoothly. We recommend that you use speakers from the same manufacture or speakers with the same tonal quality. The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system. The main speakers should be high-performance models and have enough power-handling capacity to accept the maximum output of your audio system. The other speakers do not have to be equal to the main speakers. For precise sound localization, however, it is ideal to use highperformance models that can reproduce sounds over the full range for the center speaker and the rear speakers. ■ Use of a subwoofer expands your sound field It is also possible to further expand your system with the addition of a subwoofer. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE (low frequency effect) channel with high fidelity when playing back a source encoded with Dolby Digital or DTS. The YAMAHA Active Servo Processing Subwoofer System is ideal for natural and lively bass reproduction. Speaker Placement Refer to the following diagram when you place the speakers. Main speaker (R) Rear speaker (R) Subwoofer Main speaker (L) 1.8 m Center speaker Rear speaker (L) ■ Main speakers Place the right and left main speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the TV monitor should be the same. ■ Rear speakers Place these speakers behind your listening position, facing slightly inwards, nearly 1.8 m (approx. 6 feet) above the floor. ■ Center speaker Align the front face of the center speaker with the front face of your TV monitor. Place the speaker as close to the monitor as possible, such as directly over or under the monitor and centrally between the main speakers. Note • If the center speaker is not used, the sound will be heard from the right and left main speakers. In that case, “CENTER SP” in the SET MENU is set to the NONE position. (Refer to page 34 for details.) ■ Subwoofer The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce the wall reflections. CAUTION Some types of speakers interfere with a TV monitor. If this problem occurs, move the speakers away from the monitor. If you cannot avoid installing the center speaker or subwoofer near the TV monitor, use magnetically shielded speakers. 8 0103V49608-19_EN(UCA) 8 1/11/0, 11:24 AM CONNECTIONS INTRODUCTION Before Connecting Components CAUTION Never connect this unit and other components to mains power until all connections between components have been completed. Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some components require different connection methods and have different terminal names. Refer to the instructions for each component to be connected to this unit. Use RCA-type pin plug cables for connecting audio/video components with the exception described later. The input and output terminals for pin plugs can be distinguished as follows: video signals (composite) V V White analog audio signals for the left channel L L Red analog audio signals for the right channel R R coaxial digital signals C C BASIC OPERATION Yellow After completing all connections, check them again to make sure they are correct. Connecting the Antenna (page 10) Connecting to an External Decoder (page 14) Connecting Speakers (page 15) Connecting the Power Supply Cords (page 17) ADVANCED OPERATION (U.S.A. model) + R – MAIN – + L MAINS A B SET BEFORE POWER ON CENTER R REAR (SURROUND) L + + – – PREPARATION When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect it to the terminals with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products. MAIN A OR B : 4ΩMIN. /SPEAKER A + B : 8ΩMIN. /SPEAKER CENTER : 6ΩMIN. /SPEAKER REAR : 6ΩMIN. /SPEAKER 120 V 60Hz 100W MAX. TOTAL SWITCHED MAIN A OR B : 8ΩMIN. /SPEAKER A + B : I6ΩMIN. /SPEAKER CENTER : 8ΩMIN. /SPEAKER REAR : 8ΩMIN. /SPEAKER APPENDIX Connecting an Audio Component (page 12) Connecting a Video Component (page 13) IMPEDANCE SELECTOR switch (page 17) English 9 0103V49608-19_EN(UCA) 9 1/11/0, 11:25 AM CONNECTIONS Connecting the Antennas Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. However, a properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Connect each antenna correctly to the designated terminals. ■ Indoor FM antenna (included) Indoor FM antenna Firmly insert the connector into the FM ANT terminal. The indoor FM antenna is only a simple antenna. For reception with better sound quality, installing the outdoor FM antenna (commercially available) is recommended. Note • Do not connect an outdoor FM antenna and the indoor FM antenna at the same time. ■ Outdoor FM antenna Antenna adapter (included for U.S.A. and Canada models) Note Use this adapter to match with F-type connector. You may be unable to obtain good FM radio reception depending on your local conditions (distance from the broadcasting station, interposing buildings and mountains, etc.). Consult your dealer or authorized service center and be sure to install an antenna that suits your local conditions. Install the outdoor FM antenna (commercially available) in a high place as far away from any roads as possible to avoid being affected by automobile ignition noise. 75-ohm coaxial cable 75-ohm/300-ohm antenna adapter 300-ohm feeder 10 0103V49608-19_EN(UCA) 10 1/11/0, 11:25 AM CONNECTIONS ■ AM loop antenna (included) AM loop antenna Notes • The AM loop antenna should be placed away from this unit. • The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit. INTRODUCTION The AM loop antenna can be removed from the stand and attached to a wall, etc. However, note that the reception sensitivity may deteriorate if the antenna is attached to a metal or steel reinforced wall. ■ Connecting the AM loop antenna 1 2 4 Press the tab and unlock the terminal hole. 3 Return the tab to its original position to lock the lead wires. Lightly pull the lead wires to confirm a good connection. 4 5 Attach the loop antenna to the antenna stand. 5 Antenna stand Insert the AM loop antenna lead wires into the AM ANT and GND terminals. Orient the AM loop antenna so that the best reception is obtained. If you cannot obtain good reception with the AM loop antenna, connect 5 m to 10 m of vinyl covered wire to the AM ANT terminal and extend it outdoors from a window. For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. ADVANCED OPERATION ■ Ground (GND terminal) BASIC OPERATION ■ Outdoor AM antenna Vinyl covered wire (5 m to 10 m) PREPARATION 3 1 2 APPENDIX English 11 0103V49608-19_EN(UCA) 11 1/11/0, 11:25 AM CONNECTIONS Connecting an Audio Component Turntable OUTPUT L GND R (U.S.A. model) L Analog signal R L R OUTPUT CD player L R LINE OUT L R LINE IN Signal flow Tape deck or MD recorder Be sure to connect the right channel (R), left channel (L), input (IN) and output (OUT) properly. ■ PHONO terminals These terminals are used to connect a turntable with an MM or high-output MC cartridge. If you have a turntable with a low-output MC cartridge, use an inline boosting transformer or MC head amplifier when connecting to these terminals. y Connecting the ground (earth) wire of the turntable to the GND terminal will normally minimize hum, but in some cases, better results may be obtained with the ground wire disconnected. 12 0103V49608-19_EN(UCA) 12 1/11/0, 11:25 AM CONNECTIONS Connecting a Video Component DVD/LD player L R VIDEO OUT COAXIAL DIGITAL OUT V C OPTICAL DIGITAL OUT OPTICAL DIGITAL OUT O O VIDEO OUT ANALOG AUDIO OUT V L INTRODUCTION ANALOG AUDIO OUT TV/digital TV, satellite tuner, cable TV R (U.S.A. model) PREPARATION L Analog signal R V V O L L R R V VIDEO IN V C AUDIO IN VIDEO OUT VIDEO IN Digital signal (optical) Digital signal (coaxial) Signal flow VCR ■ Audio signal terminals Be sure to connect the right channel (R), left channel (L), input (IN) and output (OUT) properly. Be sure to connect the input (IN) and output (OUT) properly. ■ Digital audio signal terminals y • The input signal from the DVD/LD input terminals is selected in the following order of priority with the input mode set to AUTO: COAXIAL terminal → OPTICAL terminal → Analog terminal. Refer to page 22 for details. • All digital signal input terminals are applicable to sampling frequencies of 32 kHz, 44.1 kHz and 48 kHz. APPENDIX If your DVD/LD player, TV/digital TV or satellite tuner, etc. has coaxial or optical digital signal output terminals, they can be connected to this unit’s COAXIAL and/or OPTICAL digital signal input terminals. To make a connection between the optical digital signal terminals, remove the cover from each terminal, and then connect them by using a commercially available optical fiber cable that conforms to EIA standards. Other cables might not function correctly. Notes • Be sure to attach the covers when the OPTICAL terminals are not being used in order to protect them from dust. • If your LD player has a Dolby Digital RF signal output terminal, be sure to use the RF demodulator (separately purchased). • No sound will be heard when connecting your LD player’s Dolby Digital RF signal output terminal directly to this unit’s COAXIAL DVD/LD digital signal input terminal. English When making connections between the digital signal terminals, you should connect the components to the samenamed analog audio signal terminals of this unit, because a digital signal cannot be recorded by a tape deck, MD recorder or VCR connected to this unit. 13 0103V49608-19_EN(UCA) 13 ADVANCED OPERATION ■ Video signal terminals TV monitor BASIC OPERATION AUDIO OUT Video signal 1/11/0, 11:25 AM CONNECTIONS ■ S VIDEO terminals DVD/LD player If your VCR, TV monitor or DVD/LD player has “S” (highresolution) video terminals, they can be connected to this unit’s S VIDEO terminals. Connect the VCR’s “S” video input and output terminals to this unit’s S VIDEO VCR OUT and IN terminals, respectively. Connect the monitor’s “S” video input terminal to this unit’s S VIDEO MONITOR OUT terminal. Connect the DVD/LD player’s “S” video output terminal to this unit’s S VIDEO DVD/LD terminal. Otherwise, connect the composite video terminals of your VCR, TV monitor or DVD/LD player to this unit’s composite video terminals. TV Monitor S VIDEO OUT S VIDEO IN S S S S Notes S Video signal S S VIDEO OUT S VIDEO IN Signal flow VCR • Use a special S VIDEO cable (commercially available) for the S VIDEO connection. • If video signals are input from both the S VIDEO input and composite input terminals, the signals will be directed to their respective output terminals. ■ VIDEO AUX terminals (on the front panel) These terminals are used to connect any video input source such as a camcorder to this unit. V L R Camcorder AUDIO OUT R AUDIO OUT L VIDEO OUT Connecting to an External Decoder External decoder MAIN OUT L R SURROUND OUT L CENTER OUT SUBWOOFER OUT R (U.S.A. model) This unit has additional 6-channel audio signal input terminals for connecting an external decoder to this unit. Connect the 6-channel audio signal output terminals of the decoder to the EXTERNAL DECODER INPUT terminals of this unit. Notes • When a source connected to these terminals is selected, the digital sound field processor cannot be used. • The settings of “CENTER SP”, “REAR SP”, “MAIN SP” and “BASS OUT” in the SET MENU have no effect on a source connected to these terminals. The setting of “MAIN LVL” is effective. (Refer to pages 34 and 35 for details.) 14 0103V49608-19_EN(UCA) 14 1/11/0, 11:25 AM CONNECTIONS Connecting Speakers Main speakers A Main speakers B Left Right INTRODUCTION Right Left (U.S.A. model) + R – MAIN – + L MAINS A PREPARATION B SET BEFORE POWER ON CENTER REAR (SURROUND) MAIN A OR B : 4ΩMIN. /SPEAKER A + B : 8ΩMIN. /SPEAKER CENTER : 6ΩMIN. /SPEAKER REAR : 6ΩMIN. /SPEAKER L + + – – 120 V 60Hz 100W MAX. TOTAL SWITCHED MAIN A OR B : 8ΩMIN. /SPEAKER A + B : I6ΩMIN. /SPEAKER CENTER : 8ΩMIN. /SPEAKER REAR : 8ΩMIN. /SPEAKER Right Center speaker CAUTIONS Left Rear speakers ■ Main speaker terminals One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either of the SPEAKERS A or B terminals. ■ Rear speaker terminals A rear speaker system can be connected to these terminals. ■ Center speaker terminal A center speaker can be connected to this terminal. APPENDIX • Use speakers with the specified impedance shown on the rear panel of this unit. • Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage the unit and/or speakers. ADVANCED OPERATION Be sure to connect the right channel (R), left channel (L), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. BASIC OPERATION Subwoofer connection If you have a subwoofer with builtin amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input terminal of the subwoofer system to the SUBWOOFER OUTPUT terminal of this unit. R English 15 0103V49608-19_EN(UCA) 15 1/11/0, 11:25 AM CONNECTIONS ■ Speaker cables 1 Remove approx. 10 mm (3/8”) of insulation from each of the speaker cable. 2 Twist the exposed wires of the cable together to prevent short circuits. 10 mm (3/8”) ■ Connecting to the MAIN SPEAKERS terminals Red: positive (+) Black: negative (–) 1 2 3 1 2 Unscrew the knob. 3 Tighten the knob to secure the wire. Insert one bare wire into the hole in the side of each terminal. ■ Connecting to the REAR and CENTER SPEAKERS terminals Red: positive (+) Black: negative (–) 1 3 2 1 2 Open the tab. 3 Return the tab to secure the wire. Insert one bare wire into the hole of each terminal. y Banana plug connections are also possible. Simply insert the banana plug connector into the corresponding terminal. 16 0103V49608-19_EN(UCA) 16 1/11/0, 11:25 AM CONNECTIONS IMPEDANCE SELECTOR Switch Select the right or left position according to the impedance of speakers in your system. Be sure to move this switch only when this unit is in the standby mode. right position The impedance must be 6 Ω or higher. The impedance must be 8 Ω or higher. Rear speakers The impedance of each speaker must be 6 Ω or higher. The impedance of each speaker must be 8 Ω or higher. If you use one pair of main speakers, the impedance of each speaker must be 4 Ω or higher. If you use one pair of main speakers, the impedance of each speaker must be 8 Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 8 Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 16 Ω or higher. [Canada model only] The impedance of each speaker must be 8 Ω or higher. After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if you will not use this unit for a long period of time. ADVANCED OPERATION SET BEFORE POWER ON MAINS left position Center speaker 120 V 60Hz 100W MAX. TOTAL SWITCHED MAIN A OR B : 4ΩMIN. /SPEAKER A + B : 8ΩMIN. /SPEAKER CENTER : 6ΩMIN. /SPEAKER REAR : 6ΩMIN. /SPEAKER MAIN A OR B : 8ΩMIN. /SPEAKER A + B : I6ΩMIN. /SPEAKER CENTER : 8ΩMIN. /SPEAKER REAR : 8ΩMIN. /SPEAKER Main speakers Connecting the Power Supply Cords ■ AC OUTLETS (SWITCHED) MAINS SET BEFORE POWER ON MAIN A OR B : 4ΩMIN. /SPEAKER A + B : 8ΩMIN. /SPEAKER CENTER : 6ΩMIN. /SPEAKER REAR : 6ΩMIN. /SPEAKER 120 V 60Hz 100W MAX. TOTAL SWITCHED MAIN A OR B : 8ΩMIN. /SPEAKER A + B : I6ΩMIN. /SPEAKER CENTER : 8ΩMIN. /SPEAKER REAR : 8ΩMIN. /SPEAKER English To AC outlet SWITCHED 17 0103V49608-19_EN(UCA) 17 APPENDIX U.S.A. and Canada models .............................. 2 OUTLETS Australia model .................................................. 1 OUTLET Use these outlets to connect the power cords from your components to this unit. The power to the AC OUTLET(S) is controlled by this unit’s STANDBY/ON (or POWER). These outlets will supply power to any connected component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the AC OUTLET(S) is 100 W. (U.S.A. model) PREPARATION IMPEDANCE SELECTOR If you use BASIC OPERATION (U.S.A. model) INTRODUCTION WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise the unit may be damaged. If this unit fails to turn on when STANDBY/ON is pressed, the IMPEDANCE SELECTOR switch may not be fully slide to either position. If so, slide the switch to either position fully when this unit is in the standby mode. 1/11/0, 11:25 AM ADJUSTING THE SPEAKER BALANCE This procedure lets you adjust the sound output level balance between the main, center and rear speakers by using the built-in test tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor, the Dolby Pro Logic decoder, Dolby Digital decoder and DTS decoder. Using the Test Tone The adjustment of each speaker sound output level should be performed at your listening position with the remote control. After completing the adjustments, use VOLUME (u/d) at your listening position to check if the adjustments are satisfactory. 2 3 1 Before You Start Adjusting 1 6 5 2,7 – + – + L R 1 Press AMP(TUNER) on the component selector. 2 Press TEST. “TEST LEFT” appears on the display. 3 Turn up the volume. You will hear a test tone (like pink noise) from each speaker for about two seconds in following order: left main speaker, center speaker, right main speaker, right rear speaker and left rear speaker. The display changes as shown below. 4 3 1 Set VOLUME to the “m” position. 2 Turn the power on. 3 Press SPEAKERS A or B to select the main speakers to be used. If you use two main speaker systems, press both A and B. 4 Set BASS, TREBLE and BALANCE to the “0” position. TEST LEFT TEST RIGHT TEST CENTER – + – + L R TEST L SUR. TEST R SUR. Notes • If the test tone cannot be heard, turn down the volume, set the unit in the standby mode and check the speaker connections. • If the test tone cannot be heard from the center speaker, check the setting of “CENTER SP” in the SET MENU. 18 0103V49608-19_EN(UCA) 18 1/11/0, 11:25 AM ADJUSTING THE SPEAKER BALANCE 4 6 Press + to raise and – to lower the level. Adjust the sound output levels of the center speaker and the rear speakers so that they become almost the same as that of the main speakers. While adjusting, the test tone is heard from the selected speaker. BASIC OPERATION Press TIME/LEVEL repeatedly to select the speaker to be adjusted. “CENTER”, “R SUR.” or “L SUR.” appears on the display. R PREPARATION 5 L Front panel INTRODUCTION Adjust BALANCE on the front panel so that the sound output level of the right main speaker and the left main speaker is the same. Note • You cannot adjust the delay time while the test tone is being heard even if “DELAY” appears on the display. 7 When the adjustment is complete, press TEST. “TEST OFF” appears on the display and the test tone stops. ADVANCED OPERATION Note • If “CENTER SP” in the SET MENU is set to the NONE position, the sound output level of the center speaker cannot be adjusted in step 6. The center channel sound is automatically output from the right and left main speakers. y APPENDIX • Once you have completed the adjustments, you can only adjust the overall volume level of your audio system by using VOLUME (or VOLUME (u/d)). • If there is insufficient sound output from the center and rear speakers, you may decrease the main speaker output level by setting “MAIN LVL” in the SET MENU to “–10 dB”. (Refer to page 35 for details.) English 19 0103V49608-19_EN(UCA) 19 1/11/0, 11:25 AM BASIC OPERATION PLAYING A SOURCE When using the remote control, press AMP(TUNER) on the component selector. 4 2 – 3 7 + – + L 4 1,6 R 7 4 b. Turn the power on. or Front panel Press SPEAKERS A or B to select the main speakers to be used. If you use two main speaker systems, press both A and B. To select a tape or an MD source Press TAPE/MD MON / EXT. DECODER (or TAPE/MD) so Front panel that the “TAPE/MD MONITOR” indicator lights up on the display. To select a source connected to the EXTERNAL DECODER INPUT terminals Press TAPE/MD MON / EXT. DECODER repeatedly (or EXT. DEC.) until “EXT. DECODER” appears on the display. Notes Set VOLUME to the “m” position. Front panel 3 Remote control • An audio source can not be played if the “TAPE/MD MONITOR” indicator lights up or if “EXT. DECODER” appears. Press TAPE/ MD MON / EXT. DECODER twice (or TAPE/MD once) to turn off the “TAPE/MD MONITOR” indicator. Press TAPE/MD MON / EXT. DECODER once (or EXT. DEC.) to turn off “EXT. DECODER”. • If you select and play a video source when the “TAPE/MD MONITOR” indicator lights up or “EXT. DECODER” appears, the play back result will be a video image from the video source and the sound from the audio source selected by using TAPE/MD MON / EXT. DECODER (or TAPE/MD or EXT. DEC.). y Front panel For the DVD/LD, TV/digital TV and satellite tuner sources, the current input mode is also shown. Refer to page 22 for details about the input mode. 20 0104V49620-24_EN(UCA) Remote control Input source a. 2 2 Front panel or 6 6 1 Select the desired input source with INPUT SELECTOR (or the input selector buttons). (Turn on the TV monitor for video sources.) The name of the selected input source appears for a moment and the arrow for the selected input source indicator lights up on the display. 20 1/12/0, 4:13 PM PLAYING A SOURCE 5 Play the source. Refer to the instructions for the source component (and page 28 for details about tuning). • When controlling an audio/video component (tape deck, MD recorder, CD player, DVD/LD player, etc.) with the remote control, press one of the component selector buttons, (TAPE/MD, CD, DVD/LD, etc.), which corresponds to the component you want to control. Refer to “PRESET REMOTE CONTROL” on page 40. 6 or – Remote control + – + L ■ When you have finished using this unit Press STANDBY/ON (or POWER) to set this unit in the standby mode. ■ BGV (background video) function The BGV function allows you to combine a video image from a video source with a sound from an audio source. (For example, you can listen to classical music while you are watching a video.) This function can only be controlled with the remote control. Play a video source, and then select an audio source with the input selector buttons on the remote control. The BGV function does not work if you select the audio source with INPUT SELECTOR on the front panel. R Front panel 7 Use the digital sound field processor. Refer to page 24. Front panel ADVANCED OPERATION or BASIC OPERATION Front panel Note • During muting, “MUTE ON” appears on the display. PREPARATION Adjust the volume to the desired output level. If desired, adjust BASS, TREBLE, BALANCE, etc. These controls are only effective for the sound from the main speakers. • BASS controls the low-frequency response. • TREBLE controls the high-frequency response. • BALANCE adjusts the balance of the output volume from the right and left main speakers. Press MUTE on the remote control. To cancel mute, press MUTE. INTRODUCTION Note ■ To mute the sound Remote control APPENDIX English 21 0104V49620-24_EN(UCA) 21 1/11/0, 10:30 AM PLAYING A SOURCE Input Mode (for the DVD/LD and TV/ digital TV and satellite tuner sources) This unit allows you to switch the input mode for sources that send both digital and analog signals to this unit. The AUTO, DTS and ANALOG input modes are provided. ■ Switching the input mode Press INPUT MODE (or the input selector button that you have pressed to select the input source on the remote control) repeatedly until the desired input mode is shown on the display. or When you turn on the power of this unit, the input mode for the DVD/LD source is always set to AUTO and for TV/ digital TV or satellite tuner source is set according to “SAT INPUT” in the SET MENU. (Refer to page 36 for details.) Front panel Remote control ■ AUTO In this mode, the input signal is selected in the following order of priority: 1. Digital signal encoded with Dolby Digital or DTS 2. Normal digital signal (PCM) 3. Analog signal (ANALOG) Note Notes • If digital signals are input from both the OPTICAL and COAXIAL terminals, the digital signal from the COAXIAL terminal is selected. ■ DTS In this mode, only a digital signal encoded with DTS is selected, even if other signals are being input at the same time. ■ ANALOG In this mode, only an analog signal is selected, even if a digital signal is being input at the same time. Select this mode when you want to use an analog signal instead of a digital signal. • Set the input mode to AUTO to play a DVD/LD source encoded with Dolby Digital. • Set the input mode to ANALOG to play a normal 2-channel source with a Dolby Surround program. • The sound output may be interrupted for some LD and DVD players in the following situation: The input mode is set to AUTO. A search is performed while playing the disc encoded with Dolby Digital or DTS, and then disc playing is restored. The sound output is interrupted for a moment because the digital signal was selected again. • The input mode cannot be changed for the CD, TUNER, TAPE/ MD, VCR, PHONO and VIDEO AUX sources because only analog signals are used for these. • The current input mode appears on the display when the DVD/ LD, TV/digital TV or satellite tuner source is selected or the input mode is changed. 22 0104V49620-24_EN(UCA) 22 1/12/0, 4:13 PM PLAYING A SOURCE ■ Notes on playing a source encoded with DTS PREPARATION • Some audio/video component, such as LD player, output different audio signals through their analog and digital terminals. Change the input mode as necessary. • If the input mode is set to AUTO for the LD source, this unit automatically determines which type of signal the LD source contains. If this unit detects a Dolby Digital or DTS signal, the decoder automatically switches to the appropriate setting and reproduces 5.1 channel sound. • If the LD player is transmitting signals by a non-normal method, this unit cannot detect the Dolby Digital or DTS signal. In this case, the decoder automatically switches to PCM or analog. • If the LD source does not contain a digital soundtrack, connect the LD player to the analog terminals and set the input mode to AUTO or ANALOG. • While you are operating the LD player, if you switch from the pause or chapter forwarding function to normal playback, you may hear the PCM or analog sound an instant before the Dolby Digital sound is played. INTRODUCTION BASIC OPERATION • If “DATA ERROR” appears on the display while playing an LD source encoded with DTS, stop playback and turn the player off and then on again. • If the digital output data of the player has been processed in any way, you may not be able to perform DTS decoding even if you make a digital connection between this unit and the player. • If you play an LD source encoded with DTS and set the input mode to ANALOG, there will be the noise of an unprocessed DTS signal. When you want to play a DTS source, be sure to connect the source to the digital input terminal and set the input mode to AUTO or DTS. • If you switch the input mode to ANALOG while playing a source encoded with a DTS signal, this unit reproduces no sound. • If you play an LD source encoded with DTS and set the input mode to AUTO, there will be a short noise at first while the unit recognizes the DTS signal and turns on the DTS decoder. This is not a malfunction, and can be avoided by setting the input mode to DTS beforehand. In addition, if you continue to play an LD encoded with DTS with the input mode setting left to AUTO, this unit automatically switches to the “DTS-decoding” mode to prevent noise from being generated during subsequent operation. (The “t” indicator lights up on the display.) No sound will be heard if a normal PCM LD is played in this mode. (The “t” indicator will flash.) To play a normal disk, set the input mode to AUTO again. ■ Notes on playing an LD source ADVANCED OPERATION APPENDIX English 23 0104V49620-24_EN(UCA) 23 9/28/0, 4:38 PM DIGITAL SOUND FIELD PROCESSOR (DSP) EFFECT 3 Selecting a DSP Program You can enhance your listening experience by selecting a DSP program. Refer to pages 25 to 27 for details about each program. – + – + L Press PRG+ or PRG– repeatedly to select the desired program. The name of the selected program appears on the display. DSP program name R 2 y If desired, adjust the delay time and the sound output level of each speaker. (Refer to pages 37 and 38 for details.) 2 Notes 3 ■ On the front panel 1 Make sure that the effect speakers (center, rear, and subwoofer) are turned on. 2 Press PROGRAM h or l repeatedly to select the desired program. The name of the selected program appears on the display. DSP program name ■ On the remote control 1 Make sure that the effect speakers (center, rear, and subwoofer) are turned on. 2 Press AMP(TUNER) on the component selector. • You can select a DSP program for each of the input sources. Once you select a program, it is linked with the input source selected at that time. So, when you select the input source next time, the same program is automatically selected. • When a monaural source is being played with PRO LOGIC/ Normal or PRO LOGIC/ENHANCED, no sound will be heard from the main speakers and the rear speakers. Sound can only be heard from the center speaker. However, if “CENTER SP” in the SET MENU is set to the NONE position, the center channel sound is output from the main speakers. • When a source connected to the EXTERNAL DECODER INPUT terminals of this unit is selected, the digital sound field processor cannot be used. Canceling the Sound Effect (turning off the effect speakers) Press EFFECT to cancel the sound effect and monitor only the main sound. Press EFFECT again to turn the sound effect back on. Remote control Notes • If the sound effect is canceled when Dolby Digital or DTS is decoding, the sounds of all channels are mixed and output from the main speakers. • If you turn off the sound effect when Dolby Digital or DTS is decoding, it may happen that the sound is output faintly or not output normally, depending on the source. In that case, turn back on the sound effect. 24 0104V49620-24_EN(UCA) 24 Front panel or 1/12/0, 4:13 PM SOUND FIELD PROGRAM When you select a CINEMA DSP program, one of the built-in decoders (Dobly Pro Logic, Dolby Digital and DTS) is turned on according to which type of signals the source being played contains. INTRODUCTION This unit incorporates a sophisticated, multi-program digital sound field processor (DSP). This processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theaterlike experience in your listening room. You can create outstanding audio sound by selecting a suitable DSP program (this will, of course, depend on what you are listening to). The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital re-creations of actual acoustic environments. No. 1 PROGRAM q/DTS SURROUND SUBPROGRAM [1] PRO LOGIC/Normal ( o ) • Input source: [4] PRO LOGIC/ENHANCED (ox) APPENDIX Dolby Surround 2-ch Dolby Digital • Output channel: 4 channels • DSP: 1 (surround) [5] DOLBY DIGITAL/ENHANCED (gx) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: 2 (surround L, R) [6] DTS DIGITAL SUR/ENHANCED (tx) • Input source: DTS • Output channel: 5.1 channels • DSP: 2 (surround L, R) This program ideally simulates the multisurround speaker systems of the 35 mm-film movie theater. Dolby Pro Logic decoding, Dolby Digital decoding or DTS decoding and digital sound field processing are precisely performed without altering the original sound orientation. The surround effect produced by the sound field folds around the viewer naturally from the rear to the right and left and toward the screen. ADVANCED OPERATION • Input source: The built-in Dolby Pro Logic decoder, Dolby Digital decoder or DTS decoder precisely reproduces the sound and effect of a source encoded with Dolby Surround, Dolby Digital or DTS. The realization of a highly efficient decoding process improves cross talk and channel separation, and makes sound positioning smoother and more precise. In this program, the digital sound field processor is not turned on. BASIC OPERATION Dolby Surround 2-ch Dolby Digital • Output channel: 4 channels • DSP: — [2] DOLBY DIGITAL/Normal ( g ) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: — [3] DTS DIGITAL SUR/Normal ( t ) • Input source: DTS • Output channel: 5.1 channels • DSP: — FEATURES PREPARATION ■ For movie or audio/video sources (Program No. 1 to No. 5: CINEMA DSP programs) English 25 0105V49625-27_EN(UCA) 25 1/11/0, 10:31 AM SOUND FIELD PROGRAM No. 2 PROGRAM MOVIE THEATER 1 SUBPROGRAM [1] 70 mm SPECTACLE (ox) • Input source: Dolby Surround 2-ch Dolby Digital • Output channel: 3 channels • DSP: 2 (presence & surround) [2] DGTL SPECTACLE (gx) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) [3] DTS SPECTACLE ( t x ) • Input source: DTS • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) [4] 70 mm SCI-FI ( o x ) • Input source: Dolby Surround 2-ch Dolby Digital • Output channel: 3 channels • DSP: 2 (presence & surround) [5] DGTL SCI-FI ( g x ) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) [6] DTS SCI-FI ( t x ) • Input source: DTS • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) 3 MOVIE THEATER 2 [1] 70 mm ADVENTURE (ox) • Input source: Dolby Surround 2-ch Dolby Digital • Output channel: 3 channels • DSP: 2 (presence & surround) [2] DGTL ADVENTURE (gx) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) [3] DTS ADVENTURE ( t x ) • Input source: DTS • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) [4] 70 mm GENERAL ( o x ) • Input source: Dolby Surround 2-ch Dolby Digital • Output channel: 3 channels • DSP: 2 (presence & surround) [5] DGTL GENERAL ( g x ) • Input source: Dolby Digital • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) [6] DTS GENERAL ( t x ) • Input source: DTS • Output channel: 5.1 channels • DSP: 3 (presence & surround L, R) FEATURES This program creates the extremely wide sound field of a movie theater. It precisely reproduces the source sound in detail, giving both the video and the sound field incredible reality. It is ideal for any kind of video source encoded with Dolby Surround, Dolby Digital or DTS (especially large-scale movie productions). Clearly reproduces dialog and sound effects in the latest sound form of science fiction films, thus creating a broad and expansive cinematic space amid the silence. You can enjoy science fiction films in a virtual-space sound field that includes Dolby Surround, Dolby Digital and DTS-encoded software employing the most advanced techniques. Ideal for precisely reproducing the sound of the newest multi-track films. The sound field is made to be similar to that of the newest movie theaters, so the reverberations of the sound field itself are restrained as much as possible. The data for the sound field of an opera house are used for the front presence, so the threedimensional feeling of the sound field is emphasized, and dialog is precisely oriented on the screen. By using the data for the sound field of a concert hall on the surround sound field, powerful reverberations are generated. You can enjoy watching action, adventure movies, etc. with strong presence. This program is for reproducing sounds on a multi-track film, and is characterized by a soft and extensive sound field. The front presence of the sound field is relatively narrow. It spatially spreads all around and toward the screen, restraining echo effect of conversations without losing clarity. For the surround sound field, the harmony of music or chorus sounds beautifully in a wide space at the rear of the sound field. 26 0105V49625-27_EN(UCA) 26 1/11/0, 10:31 AM SOUND FIELD PROGRAM No. 4 PROGRAM MONO MOVIE This program is designed specifically to enhance monaural sources. Compared to a strictly mono setting, the sound image is wider and slightly forward of the speaker pair, lending an immediacy to the overall sound. It is particularly effective for old mono movie, news broadcasts and dialog. Monaural 1 channel 1 TV SPORTS • Input source: • Output channel: • DSP: This program is furnished with a tight sound field in which the sound will not spread excessively at the front, but the rear surround produces dynamic sound expansion. It is the most suitable for sports programs. Audio/Video 2 to 5.1 channels 2 to 3 (presence & surround) INTRODUCTION • Input source: • Output channel: • DSP: 5 FEATURES ■ For Hi-Fi audio sources No. DISCO • Input source: • Output channel: • DSP: 7 This program simulates the acoustic environment of a disco in the heart of a lively city. The sound is dense and highly concentrated. 2-ch PCM/Analog audio 2 channels 1 ROCK CONCERT • Input source: • Output channel: • DSP: This program is ideally suited for rock music. You will experience a dynamic and lively sound field. 2-ch PCM/Analog audio 2 channels 1 CONCERT HALL • Input source: • Output channel: • DSP: This program creates the expansive ambience of a large concert hall. It is suited for orchestra and opera music. 2-ch PCM/Analog audio 2 channels 1 CINEMA DSP: Dolby Surround + DSP/Dolby Digital + DSP/DTS + DSP Digital sound fields are created in both the presence and rear surround zones of the Dolby Pro Logic-decoded sound field. They create a wide acoustic environment and emphasize the surround effect in the room, letting you feel as much presence as if you were watching a movie in a popular Dolby Stereo theater. ADVANCED OPERATION ■ Dolby Pro Logic + 2 digital sound fields BASIC OPERATION 8 FEATURES PREPARATION 6 PROGRAM ■ Dolby Digital or DTS + 3 digital sound fields 0105V49625-27_EN(UCA) 27 1/11/0, 10:31 AM English 27 APPENDIX Digital sound fields are created in the presence zone and independently on the left and right surround zones of the Dolby Digital-decoded or DTS-decoded sound field. They create a wide acoustic environment and strong surround effect in the room without losing high channel separation. With the wide dynamic range of Dolby Digital or DTS sound, this sound field combination lets you feel as if you were watching a movie in the newest Dolby Digital theater or DTS-installed theater. This is the most ideal home theater sound at the present time. TUNING Automatic tuning is effective when station signals are strong and there is no interference. However, if the signal from the station you want to select is weak, you must tune in to it manually (manual tuning). 5 1 Press PRESET/TUNING h once to tune in to a higher frequency and l once to tune in to a lower frequency. Press the button again if the tuning search does not stop at the desired station. Note – + – + L • If you tune in manually to an FM station, it will be automatically received in monaural mode to increase the signal quality. R y 5 42 3 Automatic Tuning 1 2 • Use the manual tuning method if the tuning search does not stop at the desired station (because the signal from the station is weak). • When tuned in to a station, the frequency of the received station is shown on the display. Manual Tuning Use INPUT SELECTOR to select the tuner as the input source. Press FM/AM to select the reception band (FM or AM). “FM” or “AM” appears on the display. 1 Use INPUT SELECTOR to select the tuner as the input source. 2 Press FM/AM to select the reception band (FM or AM). “FM” or “AM” appears on the display. or or 3 Press TUNING MODE so that the “AUTO” indicator lights up on the display. 3 Press TUNING MODE so that the “AUTO” indicator goes off. Lights up 4 Press PRESET/TUNING (EDIT) to turn “ z ” off. Goes off 4 Press PRESET/TUNING (EDIT) to turn “ z ” off. Turn “ z ” off Turn “ z ” off 5 Press PRESET/TUNING h or l to tune in to the desired station. To continue the tuning search, hold down the button. 28 0106V49628-31_EN(UCA) 28 1/11/0, 10:31 AM TUNING Automatic Preset Tuning (for FM stations only) – + – + L Press FM/AM to select the FM band. The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure in the section “To Recall a Preset Station” on page 30. PREPARATION ■ When automatic preset tuning is completed R 13 2 1 You can select the preset number from which the unit will store FM stations and/or begin tuning toward lower frequencies. Before automatic preset tuning begins (after pressing MEMORY in step 3), 1. Press A/B/C/D/E and PRESET/TUNING to select the preset number with which the first station will be stored. The automatic preset tuning will stop when stations have all been stored up to E8. 2. Press PRESET/TUNING (EDIT) to turn “ z ” off and then press PRESET/TUNING l to begin tuning toward lower frequencies. INTRODUCTION You can make use of the automatic preset tuning function for FM stations only. This function enables the unit to automatically tune in with strong signals and to sequentially store up to 40 FM stations (5 groups x 8 stations). ■ Automatic preset tuning options Notes Press TUNING MODE so that the “AUTO” indicator lights up on the display. Lights up 3 ADVANCED OPERATION Hold down MEMORY for about three seconds. The preset number, the “MEMORY” and “AUTO” indicators flash. After about five seconds, automatic preset tuning begins from the frequency currently displayed toward the higher frequencies. Received stations are sequentially stored as A1, A2 ... A8. If more than 8 stations have been tuned, they are stored as preset station numbers in other groups (B, C, D and E) in that order. BASIC OPERATION 2 • A new setting can be stored in place of the former one. • You can manually replace a preset station with another FM or AM station by simply using the manual preset tuning method. • Even if the number of received stations is not enough to be stored up to E8, automatic preset tuning is automatically ended after searching for all stations. • Only FM stations with sufficient signal strength are stored by automatic preset tuning. If the station you want to store is weak in signal strength, tune in to it manually in monaural mode and store it by using the manual preset tuning method. Flashes APPENDIX Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power cord is disconnected from the AC power outlet or the power is cut for more than one week, the memory will be erased. If so, store the stations again by using preset tuning methods. English 29 0106V49628-31_EN(UCA) 29 1/20/0, 10:56 AM TUNING Manual Preset Tuning To Recall a Preset Station You can also store up to 40 stations (5 groups x 8 stations) manually. You can recall any desired station simply by selecting the preset station number with which it was stored. You can also recall a preset station with the remote control. Press AMP(TUNER) on the component selector and press TUNER on the input selector. – + – + L R 3 4 2,5 – 1 Tune in to the desired station. Refer to page 28 for the tuning procedure. 2 Press MEMORY. The “MEMORY” indicator flashes for about five seconds. + – + L R 1 2 Flashes 3 4 5 6 Press A/B/C/D/E repeatedly to select the desired group (A to E) of preset stations before the “MEMORY” indicator goes off. Make sure that “ z ” appears on the display. The selected group appears on the display. Press PRESET/TUNING h or l to select a preset station number (1 to 8) with which you want to store the station before the “MEMORY” indicator goes off. Press h to select a higher preset station number and l to select a lower preset station number. Press MEMORY before the “MEMORY” indicator goes off. The displayed station has been stored as the preset group and number you have selected, and the reception band and frequency appear on the display. 1 2 1 Press A/B/C/D/E to select the required group of preset stations. Make sure that “ z ” appears on the display. or Front panel 2 Remote control Press PRESET/TUNING h or l (or PRESET +/–) to select a preset station number (1 to 8). The preset group and number appear on the display along with the reception band, frequency and signal strength information. or Front panel Repeat steps 1 to 5 to store other stations. Notes • A new setting can be stored in place of the former one. • The reception mode (stereo or monaural) is stored along with the station frequency. 30 0106V49628-31_EN(UCA) 30 1/12/0, 4:14 PM Remote control TUNING Exchanging Preset Stations You can exchange the assignment of two preset stations with each other. INTRODUCTION ■ Example: If you want to exchange preset station “E1” with “A5”. 2,4 + – + L PREPARATION – R Recall preset station “E1”. Refer to the procedure in the section “To Recall a Preset Station” on page 30. 2 Hold down (PRESET/TUNING) EDIT for about three second. “E1” and the “MEMORY” indicator flash. BASIC OPERATION 1 Flashes 3 ADVANCED OPERATION Recall preset station “A5” by using the buttons on the front panel. “A5” and the “MEMORY” indicator flash. Flashes 4 Press (PRESET/TUNING) EDIT again. The display shows the exchange of stations has been completed. APPENDIX English 31 0106V49628-31_EN(UCA) 31 1/20/0, 10:56 AM RECORDING A SOURCE ON TAPE, MD OR VIDEO CASSETTE Recording adjustments and other operations are performed from the tape deck, MD recorder or VCR. Refer to the instructions for these components. 2 1,4 y If a tape deck or MD recorder is being used for recording, you can monitor the sounds being recorded by pressing TAPE/MD MON / EXT. DECODER (or TAPE/MD). Notes – + – + L R 4 2 • The DSP program and the setting of VOLUME, BASS, TREBLE and BALANCE have no effect on the material being recorded. • Composite video and S video signals pass independently through this unit’s video circuits. Therefore, when recording or dubbing video signals, if your video source component is connected to provide only an S video (or only a composite video) signal, you can record only an S video (or only a composite video) signal by your VCR. • A source connected to this unit only through the digital terminals cannot be recorded by the tape deck, MD recorder or VCR connected to this unit. • A source connected to the EXTERNAL DECODER INPUT terminals of this unit cannot be recorded. • Check the copyright laws in your country to record from records, CDs, radio, etc. Recording of copyrighted material may infringe copyright laws. If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture itself may be disturbed due to those signals. 1 Set VOLUME to the “m” position. Front panel 2 Select the source you want to record. or Front panel Remote control 3 Begin recording by the tape deck, MD recorder or VCR connected to this unit. 4 Play the source and then turn up the volume to confirm the input source. or Front panel Remote control 32 0107V49632_EN(UCA) 32 1/11/0, 10:34 AM ADVANCED OPERATION SET MENU Adjustments should be performed with the remote control while watching the information on the display. 1 2 1 Press + or – repeatedly to adjust the setting. 4 Repeat steps 2 and 3 to adjust the setting of any other item in the same way. Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power cord is disconnected from the AC power outlet or the power is cut for more than one week, the settings of the SET MENU will automatically return to the preset positions and values. If so, adjust the settings of the SET MENU again. ADVANCED OPERATION 3 3 BASIC OPERATION Adjusting Items in the SET MENU Press SET MENU repeatedly to select the item you want to adjust. The selected item appears on the display. PREPARATION 1. CENTER SP 2. REAR SP 3. MAIN SP 4. BASS OUT 5. MAIN LVL 6. D.D. LFE 7. D-RANGE 8. DTS LFE 9. CNTR DELAY 10.MEM. GUARD 11.SAT INPUT 2 INTRODUCTION This unit provides you with the following items in the SET MENU to maximize the performance of your system and expand your enjoyment for audio listening and video watching. Press AMP(TUNER) on the component selector. APPENDIX English 33 0108V49633-39_EN(UCA) 33 1/11/0, 10:35 AM SET MENU Description of Each Item 1. CENTER SP 3. MAIN SP Choices: LARGE/SMALL Preset position: LARGE Choices: LRG (Large)/SML (Small)/NONE Preset position: LRG (Large) LRG (Large) Select this position if your center speaker is approximately the same size as the main speakers. In this position, fullrange signals on the center channel are directed to the center speaker. SML (Small) Select this position if you use a center speaker that is smaller than the main speakers. In this position, low bass signals (below 90 Hz) on the center channel are distributed to the SUBWOOFER OUTPUT terminal (or to the right and left main speakers if “BASS OUT” is set to the MAIN position). NONE Select this position if you do not have a center speaker (4-speaker system). In this position, full-range signals on the center channel are directed to the right and left main speakers. LARGE Select this position if your main speakers have high ability for bass reproduction. In this position, full-range signals on the main channels are directed to the right and left main speakers. SMALL Select this position if your main speakers do not have high ability for bass reproduction. However, if your system does not include a subwoofer, do not select this position. In this position, low bass signals (below 90 Hz) on the main channels are distributed to the SUBWOOFER OUTPUT terminal if “BASS OUT” is set to the SW or BOTH position. 4. BASS OUT Choices: SW/MAIN/BOTH Preset position: BOTH SW Select this position if your system includes a subwoofer. In this position, signals on the LFE channel and other low bass signals that are distributed from other channels are directed to the SUBWOOFER OUTPUT terminal when playing a source encoded with Dobly Digital or DTS. 2. REAR SP Choices: LARGE/SMALL Preset position: LARGE Note LARGE Select this position if your rear speakers have high ability for bass reproduction, or if a subwoofer is connected in parallel to the rear speaker. In this position, full-range signals on the rear channels are directed to the rear speakers. SMALL Select this position if your rear speakers do not have high ability for bass reproduction. In this position, low bass signals (below 90 Hz) on the rear channels are distributed to the SUBWOOFER OUTPUT terminal (or to the right and left main speakers if “BASS OUT” is set to the MAIN position). • When playing a 2-channel source (tape, MD, CD, video cassette etc.), select the BOTH position to direct low bass signals (below 90 Hz) to the SUBWOOFER OUTPUT terminals. MAIN Select this position if your system does not include a subwoofer. In this position, besides full-range signals on the main channels, signals on the LFE channel and other low bass signals (below 90 Hz) that are distributed from other channels are directed to the right and left main speakers. BOTH Select this position if your system includes a subwoofer. In this position, signals on the LFE channel are directed to the SUBWOOFER OUTPUT terminal. Low bass signals on the main channels are directed to both the main speakers and the SUBWOOFER OUTPUT terminal. 34 0108V49633-39_EN(UCA) 34 1/11/0, 10:35 AM SET MENU 5. MAIN LVL Choices: NORM (Normal)/–10 dB Preset position: NORM (Normal) Choices: MAX/STD (Standard)/MIN Preset position: MAX INTRODUCTION NORM (Normal) Normally select this position. 7. D-RANGE (Adjusting the dynamic range) Note –10 dB Select this position if the sound output from the main speakers is too loud and cannot be balanced with the sound output from the center and rear speakers. In this position, the sound output from the main speakers is attenuated. Control range: –20 dB to 0 dB (in 1 dB steps) Preset value: 0 dB This adjusts the output level of the LFE channel. If the LFE signals are mixed with signals of other channels and they are directed to the same speakers, the ratio of the LFE signal level to the level of the other signals can be adjusted. STD (Standard) In this position, a source encoded with Dolby Digital is reproduced in the “compressed” dynamic range of the source that is suitable for low-level listening. Note • It may happen that sound is output faintly or not output normally depending on the source. In that case, select the MAX or STD position. APPENDIX MIN In this position, the dynamic range is more reduced than in the STD position. Selecting this position will be effective when you must listen to a source at a low level. ADVANCED OPERATION Note • This adjustment is only effective when Dolby Digital is being decoded and the selected source encoded with Dolby Digital contains LFE signals. MAX In this position, a source encoded with Dolby Digital is reproduced in the original sound track’s wide dynamic range to provide you with powerful sounds just like those in a movie theater. Selecting this position will be even better if you can listen to a source at a high output level in a room specially soundproofed for audio/video enjoyment. BASIC OPERATION 6. D.D. LFE (Adjusting the output level of the LFE channel for Dolby Digital) “Dynamic range” is the difference between the maximum level and the minimum level of sounds. Sounds on a movie originally designed for movie theaters feature a very wide dynamic range. Dolby Digital technology can modify the original sound track into a home audio format with this wide dynamic range unchanged. Powerful sounds of extremely wide dynamic range are not always suitable for home use. Depending on the condition of your listening environment, it may not be possible to increase the sound output to a level as high as that in a movie theater. However, at the normal level suitable for listening in your room, the low-level parts of source sound often cannot be heard well because they will be lost among noise in your environment. Dolby Digital technology has also made it possible to reduce an original sound track’s dynamic range for a home audio format by “compressing” the sound data. PREPARATION Notes • The setting of “CENTER SP”, “REAR SP”, “MAIN SP” and “BASS OUT” have no effect on a source connected to the EXTERNAL DECODER INPUT terminals on the rear of this unit. • Once you have adjusted appropriately for “CENTER SP”, “REAR SP”, “MAIN SP”, “BASS OUT” and “MAIN LVL”, you do not have to change any settings unless your speaker system is modified. • This adjustment is only effective when Dolby Digital is being decoded. English 35 0108V49633-39_EN(UCA) 35 1/11/0, 10:35 AM SET MENU 8. DTS LFE (Adjusting the output level of the LFE channel for DTS) 10.MEM. GUARD (Locking the settings) Control range: –10 dB to +10 dB (in 1 dB steps) Preset value: 0 dB Choices: ON/OFF Preset position: OFF Note • This adjustment is effective only when DTS is being decoded and the selected source encoded with DTS contains LFE signals. This adjusts the output level of the LFE channel. If the LFE signals are mixed with signals of other channels and they are directed to the same speakers, the ratio of the LFE signal level to the level of the other signals can be adjusted. If you wish to prevent accidental alterations to the settings of the SET MENU and other adjustments on this unit, select the ON position. The following settings on this unit can be locked: • Settings of other items in the SET MENU • Settings in the TIME/LEVEL mode • Settings when using TEST 9. CNTR DELAY (Adjusting the delay of the center sound) 11.SAT INPUT (Selecting the initial input mode for a source connected to the SAT/D-TV input terminals) Control range: 0 ms to 5 ms (in 1 ms steps) Preset value: 0 ms Choices: AUTO/LAST Preset position: AUTO Note • This adjustment is only effective when Dolby Digital or DTS is being decoded and the selected source encoded with Dolby Digital or DTS contains center channel signals. This adjusts the delay between the main sound (on the main channels) and dialog, etc. (on the center channel). The larger the value, the later the dialog, etc. is generated. This makes sounds from the left main, center and right main speakers reach your listening position at the same time. This is achieved by delaying the sound from the center speaker if the distance from the center speaker to your listening position is shorter than the distance from the right and left main speaker to your listening position. The input mode for a source connected to the SAT/D-TV input terminals of this unit can be automatically set when the power of this unit is turned on. Refer to page 22 for details about the input mode. AUTO In this position, the input mode is always set to AUTO. LAST In this position, the input mode is automatically set to that selected the last time when the power of this unit was turned on. 36 0108V49633-39_EN(UCA) 36 1/11/0, 10:35 AM DELAY TIME AND SPEAKER OUTPUT LEVELS Delay Time Notes Notes • The sound output level of the center speaker cannot be adjusted when the input signal is analog, PCM audio, or encoded with Dolby Digital in 2-channel. • If “CENTER SP” in the SET MENU is set to the NONE position, the sound output level of the center speaker cannot be adjusted. This is because the center channel sound is automatically output from the right and left main speakers. • Once the sound output level has been adjusted, the level will be the same for all DSP programs. Speaker Center Right rear Left rear Subwoofer Control range (dB) –20 to +10 –20 to +10 –20 to +10 –20 to 0 Preset value 0 0 0 0 BASIC OPERATION ADVANCED OPERATION APPENDIX • Adding too much delay will cause an unnatural effect with some sources. • The sound is momentarily interrupted while adjusting the delay time. Preset Control Program value range (ms) 1. PRO LOGIC/Normal 15 to 30 20 DOLBY DIGITAL/Normal 0 to 15 5 DTS DIGITAL SUR/Normal 0 to 15 5 PRO LOGIC/ENHANCED 15 to 30 20 DOLBY DIGITAL/ENHANCED 0 to 15 5 DTS DIGITAL SUR/ENHANCED 0 to 15 5 2. 70 mm SPECTACLE 15 to 30 23 DGTL SPECTACLE 1 to 99 15 DTS SPECTACLE 1 to 99 15 70 mm SCI-FI 15 to 30 20 DGTL SCI-FI 1 to 99 16 DTS SCI-FI 1 to 99 16 3. 70 mm ADVENTURE 15 to 30 20 DGTL ADVENTURE 1 to 99 15 DTS ADVENTURE 1 to 99 15 70 mm GENERAL 15 to 30 20 DGTL GENERAL 1 to 99 15 DTS GENERAL 1 to 99 15 4. MONO MOVIE 1 to 99 49 5. TV SPORTS 1 to 99 9 6. DISCO 1 to 99 40 7. ROCK CONCERT 1 to 99 16 8. CONCERT HALL 1 to 99 44 If desired, you can adjust the sound output level of each speaker even if it has already been adjusted in “ADJUSTING THE SPEAKER BALANCE” on pages 18 and 19. PREPARATION You can adjust the time difference between the beginning of the sound from the main speakers and the beginning of the sound effect from the rear speakers. The larger the value, the later the sound effect is generated. The delay time can be individually adjusted to all DSP programs. Sound Output Level of the Center, Right Rear and Left Rear Speakers, and Subwoofer INTRODUCTION When using the digital sound field processor with the Dolby Pro Logic decoder, Dolby Digital decoder or DTS decoder, you can adjust the delay time between the main sound and sound effect, and each speaker’s output level as you wish. English 37 0108V49633-39_EN(UCA) 37 1/20/0, 10:57 AM DELAY TIME AND SPEAKER OUTPUT LEVELS Adjusting Method 3 Press + or – to adjust the delay time or speaker output levels. 4 Repeat steps 2 and 3 to adjust the settings of any other item. Adjustments should be performed with the remote control while watching the information on the display. 1 3 2 1 Press AMP(TUNER) on the component selector. 2 Press TIME/LEVEL repeatedly to select the item you want to adjust. Each time you press TIME/LEVEL, the selected item changes and appears on the display as below. Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power cord is disconnected from the AC power outlet or the power is cut for more than one week, the latest values for the delay time and the center/rear/ subwoofer output levels that were set will automatically return to the preset values. If so, adjust the delay time and output levels again. DELAY CENTER R SUR. L SUR. SWFR Note • Depending on the setting of the SET MENU, you may not be able to select all these items. 38 0108V49633-39_EN(UCA) 38 1/11/0, 10:35 AM SLEEP TIMER Notes • First press AMP(TUNER), TAPE/MD, CD or DVD/LD on the component selector to set the SLEEP timer for this unit. • The SLEEP timer is effective for the components connected to the AC OUTLET(S) on the rear panel of this unit. Note Play a source you want to enjoy when you are going to sleep. 2 Press SLEEP repeatedly to select the desired SLEEP time. Each time you press SLEEP, the SLEEP time will change as below: 90 60 • The SLEEP timer can also be canceled by setting the unit in the standby mode by using POWER on the remote control (or STANDBY/ON), or by disconnecting the AC power cord from the AC power outlet. BASIC OPERATION 1 120 Press SLEEP repeatedly until “SLEEP OFF” appears on the display. It will soon disappear and the “SLEEP” indicator will go off. 30 The SLEEP timer is off (SLEEP OFF). (This is the state before SLEEP is pressed.) ADVANCED OPERATION Flashes 3 PREPARATION Setting the SLEEP Timer Canceling the Selected SLEEP Timer INTRODUCTION The SLEEP timer can be used to automatically set this unit in the standby mode. This timer is useful when you are going to sleep while enjoying a broadcast or other desired input source. The SLEEP timer can only be set with the remote control. The “SLEEP” indicator soon lights up on the display after the SLEEP timer has been set. The display returns to the previous indication. Lights up APPENDIX English 39 0108V49633-39_EN(UCA) 39 1/12/0, 4:14 PM PRESET REMOTE CONTROL The provided remote control is factory set to control not only this unit but also most YAMAHA audio components connected to it. There are eight component selector buttons. Press one of these buttons which corresponds to the component you want to control with the remote control. For example, if you press CD on the component selector, the remote control is set to the CD operation mode, allowing the CD player to be controlled by the buttons on the remote control. AMP(TUNER) You can perform the basic operations of this unit. Refer to page 7. CD The code for a YAMAHA CD player is factory set. DVD/LD & DVD MENU An LD player can be controlled in the DVD/LD mode. A DVD player can be controlled in the DVD/LD and DVD MENU modes. The code for a YAMAHA DVD player is factory set. If the remote control does not operate your YAMAHA DVD player, you need to set the code number “0048”. TAPE/MD The code for a YAMAHA tape deck is factory set. (The code for the YAMAHA MD recorder can also be set.) VCR A VCR can be controlled. TV A TV can be controlled. CBL/SAT A cable TV or satellite tuner can be controlled. Note • The button functions on the remote control differ depending on the operation mode. Refer to the following pages for details. Controlling the Components Connected to This Unit ■ Example: To control YAMAHA CD player 5 2 3 4 7 6 1 Make sure that VOLUME is set to the “m” position. 2 Press AMP(TUNER) on the component selector. 3 Turn on the power. 4 Press CD on the input selector. 5 Press CD on the component selector. 6 Press p. Refer to page 42 for the CD player operation buttons. 7 Adjust the volume. If you set the remote control with the manufacturers’ codes listed from page i at the end of this manual, you can control other brands of components. Refer to “Setup codes” on page 45 for details. 40 0109V49640-46_EN(UCA) 40 1/11/0, 10:35 AM PRESET REMOTE CONTROL Description of Each Mode ■ TAPE/MD MODE INTRODUCTION Note • TV VOLUME functions if you have set the code for your TV. Press TAPE/MD. PREPARATION POWER (TAPE) This button turns this unit on if you have set the code for a YAMAHA tape deck. This button turns on the tape deck that has a remote control with a power button if you have set the code for another manufacturer. (MD) This button turns this unit on if you have set the code for the YAMAHA MD recorder. Input selector buttons BASIC OPERATION EFFECT VOLUME MUTE DISPLAY (MD) APPENDIX DECK A/B (TAPE) This button selects deck A or B on a double-cassette tape deck. e PAUSE (MD) This button gives a pause in operation. a DIR B (TAPE) This button selects the playing direction of deck B. SKIP+ (MD) This button skips to the next track. s STOP This button stops operation on a tape deck or MD recorder. f FAST FORWARD (TAPE) This button winds a tape fast forward. SEARCH (MD) This button initiates a fast-forward search on the track that is playing to find the point from which you want to listen. ADVANCED OPERATION SLEEP r REC/PAUSE This button gives a pause in recording on a tape deck or MD recorder. p PLAY This button plays a tape or an MD. b DIR A (TAPE) This button selects the playing direction of deck A. SKIP– (MD) This button skips to the previous track. w REWIND (TAPE) This button rewinds a tape. SEARCH (MD) This button initiates a backward search on the track that is playing to find the point from which you want to listen. TV VOLUME English The dark-shaded buttons do not function. Refer to the instructions for details of each component. 41 0109V49640-46_EN(UCA) 41 1/11/0, 10:36 AM PRESET REMOTE CONTROL ■ CD MODE Note • TV VOLUME and TV INPUT function if you have set the code for your TV. Press CD. POWER This button turns this unit on if you have set the code for a YAMAHA CD player. This button turns on the CD player that has a remote control with a power button if you have set the code for another manufacturer. Input selector buttons EFFECT DISC SKIP +/– (for a CD player with CD changer) These buttons skip to the next or previous CD. VOLUME MUTE SLEEP TV VOLUME DISPLAY TV INPUT p PLAY This button plays a CD. b SKIP– This button skips to the beginning of the previous track. w SEARCH This button initiates a backward search on the track that is playing to find the point from which you want to listen. e PAUSE This button gives a pause in operation. The button functions as PAUSE/STOP* for operating a YAMAHA CD player under factory setting. a SKIP+ This button skips to the beginning of the next track. s STOP This button stops operation. The button functions as PAUSE/STOP* for operating YAMAHA CD players. f SEARCH This button initiates a fast-forward search on the track that is playing to find the point from which you want to listen. y PAUSE/STOP function Press the button once to give a pause in operation and press once more to stop operation. The dark-shaded buttons do not function. Refer to the instructions for details of each component. 42 0109V49640-46_EN(UCA) 42 1/11/0, 10:36 AM PRESET REMOTE CONTROL ■ DVD/LD MODE Note • TV VOLUME and TV INPUT function if you have set the code for your TV. INTRODUCTION Press DVD/LD. Input selector buttons EFFECT DISC SKIP +/– PREPARATION POWER (DVD) This button turns this unit on if you have set the code for a YAMAHA DVD player. This button turns on the DVD player that has a remote control with a power button if you have set the code for another manufacturer. (LD) This button turns this unit on if you have set the code for a YAMAHA LD player. This button turns on the LD player that has a remote control with a power button if you have set the code for another manufacturer. VOLUME MUTE SLEEP PAUSE SKIP – STOP TV VOLUME DISPLAY TV INPUT SKIP + PLAY SEARCH SEARCH BASIC OPERATION ■ DVD MENU MODE Note • TV VOLUME and TV INPUT function if you have set the code for your TV. POWER This button turns the unit on if you have set the code for a YAMAHA DVD player. This button turns on the DVD player that has a remote control with a power button if you have set the code for another manufacturer. ADVANCED OPERATION Press DVD MENU. Numeric buttons CLEAR +10 DISC SKIP +/– VOLUME MUTE RETURN MENU DOWN INDEX APPENDIX MENU UP MENU LEFT TV VOLUME TV INPUT MENU RIGHT MENU SELECT MENU TITLE English The dark-shaded buttons do not function. Refer to the instructions for details of each component. 43 0109V49640-46_EN(UCA) 43 1/11/0, 10:36 AM PRESET REMOTE CONTROL ■ VCR MODE ■ CBL/SAT MODE Note Note • TV VOLUME, TV INPUT and TV SLEEP function if you have set the code for your TV. VCR POWER Press VCR. • TV VOLUME, TV INPUT and TV SLEEP function if you have set the code for your TV. CBL/SAT POWER Press CBL/SAT. CHANNEL EFFECT CHANNEL ENTER VCR CHANNEL +/– VOLUME MUTE TV VOLUME DISPLAY TV INPUT VCR PAUSE TV SLEEP VCR REC Press this button twice to start recording. CHANNEL CBL/SAT CHANNEL +/– VOLUME MUTE TV SLEEP MENU UP MENU LEFT VCR PLAY VCR FAST FORWARD VCR STOP VCR REWIND MENU DOWN RECALL ■ TV MODE Note • You can control your VCR if you have set the code for it. TV POWER Press TV. CHANNEL TV CHANNEL +/– VOLUME TV MUTE TV SLEEP VCR REC Press this button twice. VCR STOP VCR REWIND EFFECT CHANNEL ENTER TV VOLUME DISPLAY TV INPUT VCR PAUSE VCR PLAY VCR FAST FORWARD The dark-shaded buttons do not function. Refer to the instructions for details of each component. 44 0109V49640-46_EN(UCA) 44 1/11/0, 10:36 AM +100 CHANNEL ENTER TV VOLUME DISPLAY TV INPUT MENU RIGHT MENU SELECT MENU PRESET REMOTE CONTROL Advanced Information ■ Setup codes 1 2 Turn on the VCR to be used. 3 Press both VOLUME buttons (u/d) at the same time for about four seconds. The indicator flashes twice. 4 Use the numeric buttons to enter the four-digit code for the second (and third) VCR. Make sure that the indicator flashes twice. If the indicator does not flash, repeat step 3 and re-enter the code. 5 Press POWER (or any other button) on the remote control to check if you have set the code correctly. If the VCR cannot be controlled with the remote control, try setting another code for the same manufacturer. Press both VOLUME buttons (u/d) at the same time for about four seconds. The indicator flashes twice. Use the numeric buttons to enter the four-digit manufacturer’s code for the component to be used. Make sure that the indicator flashes twice. If the indicator does not flash, repeat step 3 and re-enter the code. Press POWER (or any other button) on the remote control to check if you have set the code correctly. If your component cannot be controlled with the remote control, try setting another code for the same manufacturer. Press CBL/SAT or DVD MENU on the component selector. ADVANCED OPERATION 5 1 2 BASIC OPERATION 4 Press one of the component selector buttons which corresponds to the component to be controlled. Note • If you want to control a second (and third) VCR in the DVD MENU mode, you must set the code for an LD player in the DVD/LD mode. PREPARATION 3 Turn on your component to be used. You can control a second (and third) VCR in the CBL/SAT and DVD MENU modes if a cable TV or satellite tuner, or DVD player is not being used. INTRODUCTION You can set the code for the manufacturer of your component after pressing the component selector buttons other than AMP(TUNER). ■ To use a second (and third) VCR Notes APPENDIX • You can set only one code for one mode. • In the DVD/LD and DVD MENU modes: – Be sure to press DVD/LD on the component selector before entering the code for the DVD/LD player. The code set in the DVD/LD mode is also simultaneously set in the DVD MENU mode. You cannot set the code for a DVD player after pressing DVD MENU on the component selector. – DVD MENU operations cannot be performed for some DVD players. • A second (and third) VCR can be controlled. Refer to “To use a second (and third) VCR” for details. • If your component does not respond to any of the codes listed for the manufacturer, use the original remote control supplied with your component. English 45 0109V49640-46_EN(UCA) 45 1/11/0, 10:36 AM PRESET REMOTE CONTROL ■ Returning to the factory-set codes To return all components to the factory-set codes, follow these steps. 1 Press one of the component selector buttons other than AMP(TUNER). 2 Press both VOLUME buttons (u/d) at the same time for about four seconds. The indicator flashes twice. 3 Enter the code number “9990”. Make sure that the indicator flashes twice. To return each component to the factory-set codes, follow these steps. 1 Press one of the component selector buttons which corresponds to the component to be returned to the factory-set code. 2 Press both VOLUME buttons (u/d) at the same time for about four seconds. The indicator flashes twice. 3 Enter the code number “0000”. Make sure that the indicator flashes twice. The following codes are factory set. Component selector button TV CBL/SAT VCR DVD/LD CD TAPE/MD Component Code TV Satellite tuner VCR DVD player CD player Tape deck 0101 0006 0002 0008 (YAMAHA DVD player) 0005 (YAMAHA CD player) 0004 (YAMAHA Tape deck) We recommend that you write all the code numbers you have set on the “Quick Reference Card”. 46 0109V49640-46_EN(UCA) 46 1/11/0, 10:36 AM APPENDIX TROUBLESHOOTING ■ General SYMPTOM CAUSE REMEDY Refer to page The power cord is not connected or the plug is not completely inserted. Firmly connect the power cord. 17 The IMPEDANCE SELECTOR switch on the rear panel is not fully set to the right or left position. Set the switch fully to the right or left position when the unit is in the standby mode. 17 The unit does not work normally. The internal microcomputer has been frozen by an external electric shock (lightning, excessive static electricity, etc.) or by a power supply with low voltage. Set the unit in the standby mode and disconnect the AC power cord from the AC power outlet. After about 30 seconds have passed, connect the power and operate the unit again. — No sound and/or no picture. Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables may be defective. An appropriate input source has not been selected. Select an appropriate input source with INPUT SELECTOR or TAPE/MD MON / EXT. DECODER (or the input selector buttons). 20 The speaker connections are not secure. Secure the connections. 15 SPEAKERS have not been set properly. Set SPEAKERS corresponding to the speakers in use to the ON position. 20 The sound is muted. Set VOLUME to the “m” position, press MUTE to cancel a mute and adjust the volume. 21 Digital signals other than PCM audio and the signals encoded with Dolby Digital or DTS which this unit cannot reproduce are being input to this unit by a CD-ROM, etc. Play a source whose signals this unit can reproduce. — No picture. There is no S VIDEO connection between this unit and the TV monitor, although S video signals are being input to this unit. Connect the monitor’s “S” video input terminal to this unit’s S VIDEO MONITOR OUT terminal. 14 The sound suddenly goes off. The protection circuit has been activated because of a short circuit, etc. Set the unit in the standby mode and then turn on to reset the protection circuit. — The SLEEP timer has functioned. Turn on the power, and play the source again. 39 Incorrect cable connections. Connect the cables properly. If the problem persists, the cables may be defective. 15 21 Press EFFECT to turn it on. 24 A Dolby Surround, Dolby Digital or DTS decoding DSP program is being used with material not encoded with Dolby Surround, Dolby Digital or DTS. Select another DSP program. 27 No sound from the center speaker. The sound output level of the center speaker is set to minimum. “CENTER SP” in the SET MENU is set to the NONE position. Raise the level of the center speaker. 37 Select the LRG or SML position. 34 Incorrect DSP program is selected. Select the appropriate program. The source encoded with Dolby Digital or DTS does not have a center channel signal. 25, 26, 27 — The output level of the rear speakers is set to minimum. Raise the output level of the rear speakers. 37 A monaural source is being played with the PRO LOGIC/Normal or PRO LOGIC/ENHANCED program. Select another DSP program suitable for the monaural source. 27 English No sound from the rear speakers. APPENDIX Adjust it to the appropriate position. The sound effect is off. ADVANCED OPERATION Incorrect setting of BALANCE. No sound from the effect speakers. BASIC OPERATION Only the speaker on one side can be heard. 12, 13 47 0110V49647-52_EN(UCA) 47 PREPARATION The unit fails to turn on when STANDBY/ON is pressed, or enters in the standby mode soon after the power has been turned on. INTRODUCTION If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center. 1/11/0, 10:37 AM TROUBLESHOOTING SYMPTOM No sound from the subwoofer. CAUSE “BASS OUT” in the SET MENU is set to the SW or MAIN position when playing a 2-channel source. REMEDY Select the BOTH position. 34 — The source does not contain low bass signals (below 90 Hz). A “humming” sound can be heard. Refer to page Incorrect cable connections. Firmly connect the audio plugs. If the problem persists, the cables may be defective. No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit. 12 The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The turntable should be connected to the unit through the MC head amplifier. 12 The volume level cannot be increased, or the sound is distorted. The component connected to the TAPE/MD OUT (REC) terminals of this unit is in the standby mode. Turn on the power to the component. — The sound effect cannot be recorded. It is not possible to record the sound effect by a tape deck or MD recorder connected to the TAPE/MD OUT (REC) terminals of this unit. The DVD/LD, TV/digital TV or satellite tuner source cannot be recorded by tape deck, MD recorder or VCR connected to this unit. The DVD/LD player, TV/digital TV or satellite tuner is connected to the unit only through the digital terminals. Make additional connections between the analog terminals. 13 Adjusting this unit by using SET MENU, TIME/ LEVEL or TEST cannot be performed. “MEM. GUARD” in the SET MENU is set to the ON position. Set “MEM. GUARD” to the OFF position. 36 12, 13 32 ■ Tuner SYMPTOM FM stereo reception is noisy. There is distortion, and clear reception cannot be obtained even with a good FM FM antenna. CAUSE The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor. There is multipath interference. REMEDY Check the antenna connections. Try using a high-quality directional FM antenna. Use the manual tuning method. Adjust the antenna position to eliminate multipath interference. The desired station cannot be tuned in with the automatic tuning method. The station is too weak. Use the manual tuning method. Use a high-quality directional FM antenna. Previously preset stations can no longer be tuned in. The unit has been disconnected for a long period. Re-store the stations. The desired station cannot be tuned in with the automatic tuning method. The signal is weak or the antenna connections are loose. Tighten the AM loop antenna connections and orient it for best reception. Use the manual tuning method. Noises result from lightning, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat, but it is difficult to eliminate all noise. Move this unit away from the TV. There are continuous AM crackling and hissing noises. There are buzzing and whining noises (especially in the evening). A TV set is being used nearby. 48 0110V49647-52_EN(UCA) 48 1/11/0, 10:37 AM Refer to page 10, 28 10 10, 28 29 11, 28 11 — TROUBLESHOOTING ■ Remote control SYMPTOM The remote control does not work. REMEDY Refer to page Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. Reposition the unit. The batteries are weak. Replace all batteries with new ones. 2 The component to be controlled has not been selected. Press one of the component selector buttons which corresponds to the component to be controlled. 40 The manufacturer’s code has not been set properly. Enter the code again. 45 3 INTRODUCTION The unit or other component cannot be controlled. CAUSE Try setting another code for the same manufacturer. ■ Others CAUSE REMEDY Refer to page The sound is degraded when listening with headphones to a tape deck or CD player connected to this unit. This unit is in the standby mode. Turn on the power of the unit. — There is noise interference from digital or high-frequency equipment, or the unit. The unit is too close to the digital or highfrequency equipment. Move the unit further away from such equipment. — SYMPTOM CAUSE REMEDY Refer to page The player which plays back the source is not connected to a digital audio signal input terminal of this unit. The player must be connected to a digital audio signal input terminal of this unit besides the analog audio signal terminal connections. 13 The input mode is set to ANALOG on this unit. Set a proper input mode to turn on the built-in DTS decoder. 22 A percussive noise is heard when playing back a source encoded with DTS. If the input mode is set to AUTO, depending on some sources, there may be a noise heard while this unit is identifying the format of the input signal. Set the input mode of the currently selected input source to DTS. 22 No sound is heard when playing back a source encoded with DTS, even if the input mode is set to AUTO on this unit. The built-in DTS decoder does not function because the player has a digital volume control and it is set at a position other than “maximum,” “neutral” or “ineffective.” Set the player’s digital volume control at the maximum, neutral or ineffective position. — No sound is heard when playing back an MD or DAT on which has been recorded a source encoded with DTS. A source encoded with DTS cannot be recorded on an MD or DAT. No sound is heard when playing back a source (CD, etc.) even if the currently selected input mode is AUTO. In the AUTO mode, the DTS-decoding mode cannot be automatically changed to the normal (PCM) digital signal input mode. ADVANCED OPERATION A loud hissing noise is heard when playing back a source encoded with DTS. — Set the input mode to AUTO again. BASIC OPERATION ■ When playing back a source encoded with DTS PREPARATION SYMPTOM 23 APPENDIX Notes 49 0110V49647-52_EN(UCA) 49 1/11/0, 10:37 AM English • It is necessary to use a DTS decoder to play back a source encoded with DTS, so the player which plays back the source must be connected to a digital audio input terminal of this unit in the way described in this manual. If this connection is not made or only a D-to-A converter is being used without using a DTS decoder, only a loud hissing noise will be heard when you play back the source. • If you make a search (or skip, etc.) operation while playing back a source encoded with DTS, the “t” indicator goes off. This is because this unit automatically changes the DTS-decoding mode to the standard (PCM) digital signal input mode to prevent a noise from being output. SPECIFICATIONS AUDIO SECTION FM SECTION • Minimum RMS Output Power 20 Hz to 20 kHz, 0.06% THD, 8 ohms Main L/R, Center, Rear L/R ......................................... 70 W*/65 W 1 kHz, 0.09% THD, 8 ohms Main L/R, Center, Rear L/R ....................................... 80 W*/70 W • Tuning Range .................................... 87.5/87.50 to 107.9/108.00 MHz • Maximum Output Power (EIAJ) 1 kHz, 10% THD, 8 ohms ........................................................ 100 W • DIN Standard Output Power 1 kHz, 0.7% THD, 4 ohms ....................................................... 100 W • IEC Output Power 1 kHz, 0.06% THD, 8 ohms ....................................................... 70 W • Dynamic Power (IHF) 8/6/4/2 ohms .................... 100/120/140/160 W*, 90/110/130/150 W • Damping Factor 20 Hz to 20 kHz, 8 ohms ................................................................ 60 • Frequency Response CD etc. to MAIN L/R ................................ 20 Hz to 20 kHz, ±0.5 dB • Total Harmonic Distortion (20 Hz to 20 kHz) CD etc. to MAIN L/R, 1/2 power, 8 ohms ............................ 0.025% • Signal-to-Noise Ratio (IHF-A Network) CD etc. to MAIN L/R (150 mV, Input Shorted) ........................................................ 96 dB (250 mV, Input Shorted) ....................................................... 100 dB • Residual Noise (IHF-A Network) MAIN L/R .............................................................................. 150 µV • Input Sensitivity/Impedance CD etc. ................................................................. 150 mV/47 k-ohms EXT. DECODER ......................................... 150 mV/40 – 47 k-ohms • Output Level/Impedance REC OUT ........................................................... 150 mV/1.2 k-ohms SUBWOOFER ....................................................... 4.0 V/1.2 k-ohms PHONES ................................................................. 0.47 V/390 ohms • Usable Sensitivity (DIN) Mono (S/N 26 dB) ................................................................... 0.9 µV Stereo (S/N 46 dB) ................................................................... 28 µV • Selectivity (two signals, 40 kHz Dev., ±300 kHz) ...................... 55 dB • Signal-to-Noise Ratio (Mono/Stereo) DIN ................................................................................. 75 dB/69 dB IHF ................................................................................. 81 dB/75 dB • Harmonic Distortion (1 kHz) Mono/Stereo ........................................................................ 0.1/0.2% • Stereo Separation (1 kHz) ........................................................... 48 dB • Frequency Response ........................................ 20 Hz to 15 kHz, ±1 dB • Antenna Input ...................................................... 75 ohms, Unbalanced AM SECTION • Tuning Range ............................................ 530/531 to 1,710/1,611 kHz • Usable Sensitivity ................................................................. 300 µV/m • Signal-to-Noise Ratio ................................................................... 52 dB • Antenna ........................................................................... Loop antenna GENERAL • Power Supply [U.S.A. and Canada models] .................................. AC 120 V, 60 Hz [Europe, U.K. and Singapore models] .................... AC 230 V, 50 Hz [Australia model] ..................................................... AC 240 V, 50 Hz [China model] ......................................................... AC 220 V, 50 Hz [General model] ............................. AC 110/120/220/240 V, 50/60 Hz • Power Consumption ...................................................... approx. 220 W • AC Outlets (100 W max. total) [U.K. and Australia models] ..................................... 1 (SWITCHED) [Other models] .......................................................... 2 (SWITCHED) • Channel Separation (Vol. –30 dB) CD etc. (Input 5.1 k-ohms Terminated, 1 kHz/10 kHz) ..................................................................................... 60 dB/45 dB • Dimensions (W x H x D) ..................... 435 x 151 x 391 mm (17-1/8’’ x 5-15/16’’ x 15-3/8’’) • Tone Control Characteristics BASS: Boost/cut .......................................................... ±10 dB/50 Hz TREBLE: Boost/cut ................................................... ±10 dB/20 kHz VIDEO SECTION • Accessories ................................................................ AM loop antenna .......................................................................... Indoor FM antenna ..................... 75-ohm/300-ohm antenna adapter (U.K. model only) ........................ Antenna adapter (U.S.A. and Canada models only) ................................................................................. Remote control ........................................................................................... Batteries • Video Signal Type ........................................................... NTSC or PAL Specifications are subject to change without notice. * for U.S.A. and Canada models • Weight ............................................................................ 10 kg (22 lbs.) • Video Signal Level ...................................................... 1 Vp-p/75 ohms • Signal-to-Noise Ratio .................................................................. 50 dB • Monitor Out Frequency Response .................... 5 Hz to 10 MHz, –3 dB 50 0110V49647-52_EN(UCA) 50 9/28/0, 4:38 PM GLOSSARY ■ Dolby Digital Dolby Digital is a digital surround sound system that provides completely independent multi-channel audio to you. Dolby Digital provides five full-range channels in what is sometimes referred to as a “3/2” configuration: three front channels (left, center and right), and two surround channels. A sixth bass-only effect channel is also provided for output of LFE (low frequency effect), or low bass effects that are independent of other channels. (This is called the “LFE channel”.) This channel is counted as 0.1, thus giving rise to the term 5.1 channels in total. The wide dynamic range of sound reproduced by the five full-range channels and precise sound orientation by digital sound processing provides listeners with excitement and realism that have never been experienced before. ■ S VIDEO Signal The S VIDEO signal is separated and transmitted as the Y signal which indicates the luminance and the C signal which indicates the chroma of the video signal (composite signal). Using the S VIDEO terminal eliminates video signal transmission loss and allows recording and playback of even more beautiful images. APPENDIX English DTS was developed to replace analog soundtracks of movies with six discrete channels of digital soundtracks, and it is now installed in many theaters around the world. The DTS digital playback system changed the way we experienced movies in theaters with six discrete channels of superb digital audio. DTS technology, through intense research and development has made it possible to deliver similar encode/decode discrete technology to home audio surround-sound entertainment. DTS Digital Surround is an encode/decode system which delivers six channels of master-quality, 20-bit audio; technically, it is 5.1 channels, which means 5 full-range (left, center, right and two surround) channels, plus a subwoofer (LFE) channel (as “0.1”). It is compatible with the 5.1 speaker configurations that are currently available for home theater systems. This channel is for reproduction of low bass signals. The frequency range for this channel is 20 Hz to 120 Hz. This channel is called the channel 0.1 because it only reproduces a low frequency range compared to the full-range from 20 Hz to 20 kHz that is reproduced by the 5 channels in a Dolby Digital or DTS 5.1 channel system. 51 0110V49647-52_EN(UCA) 51 ADVANCED OPERATION ■ DTS (Digital Theater System) Digital Surround ■ LFE 0.1 Channel BASIC OPERATION The Dolby Surround and Dolby Digital sound and DTS systems show their full ability in a large movie theater, because movie sounds are originally designed to be reproduced in a large movie theater that uses a multitude of speakers. Trying to create a sound environment similar to that of a movie theater in your home is difficult because of the room size, material inside the walls, the number of speakers, and so on. In other words, your listening room is very different from a movie theater. However, YAMAHA DSP technology allows you to create nearly the same sound experience as that of a large movie theater in your home by compensating for the lack of presence and dynamics in the listening room with original digital sound fields combined with Dolby Surround, Dolby Digital or DTS Digital Surround sounds. The YAMAHA “CINEMA DSP” logo indicates those programs that are created by the combination of YAMAHA DSP technology and Dolby Surround, Dolby Digital or DTS. PREPARATION ■ CINEMA DSP CINEMA DSP Dolby Surround uses four discrete channels and five speakers to reproduce realistic and dynamic sound effects: two main channels (left and right), a center channel for dialog, and a rear channel for special sound effects. The rear channel reproduces sound within a narrow frequency range. Most video tapes and laser discs include Dolby Surround encoding, as do many TV and cable broadcasts. The Dolby Pro Logic decoder built into this unit employs a digital signal processing system that stabilizes each channel for even more accurate sound positioning than is available with standard analog processors. INTRODUCTION ■ Dolby Surround 1/11/0, 10:37 AM INDEX A M Accessories .......................................................................... 2 AC outlet ........................................................................... 17 Antennas ...................................................................... 10, 11 Muting ............................................................................... 21 B BALANCE ........................................................................ 21 BGV (background video) function .................................... 21 C Canceling sound effect ...................................................... 24 CINEMA DSP ............................................................. 27, 51 Connections Antennas ................................................................ 10, 11 Audio components (tape deck/MD recorder, CD player and turntable) .............................................................. 12 Digital connections ...................................................... 13 Speakers ...................................................................... 15 TV monitor .................................................................. 13 Video components (DVD/LD player, VCR and TV/ digital TV, satellite tuner) ............................................ 13 P Playing ............................................................................... 20 Preset stations To recall a preset station .............................................. 30 Exchanging preset stations .......................................... 31 Preset tuning Automatic preset tuning .............................................. 29 Manual preset tuning ................................................... 30 R Recording .......................................................................... 32 Remote control Basic operations ............................................................ 7 Batteries ......................................................................... 2 Component selector ................................................. 7, 40 Factory-set code .......................................................... 46 Manufacturer’s codes .......... i (at the end of this manual) Setup codes .................................................................. 45 D S Delay time (TIME/LEVEL mode) .................................... 37 Display ................................................................................. 6 Dolby Digital ..................................................................... 51 Dolby Surround ................................................................. 51 DSP program ............................................................ 24 to 27 DTS Digital Surround ....................................................... 51 SET MENU ....................................................................... 33 Sleep timer ......................................................................... 39 Speaker Output levels (TIME/LEVEL mode) .......................... 37 Output mode (SET MENU) .................................. 34, 35 Speaker balance (test tone) .......................................... 18 Placement ...................................................................... 8 STANDBY/ON .................................................................... 4 E External decoder ................................................................ 14 T F Front panel ........................................................................... 4 I IMPEDANCE SELECTOR switch ................................... 17 Input mode ......................................................................... 22 Test tone ....................................................................... 18, 19 Tone controls ..................................................................... 21 Tuning Automatic tuning ......................................................... 28 Manual tuning ............................................................. 28 L LFE ........................................................................ 35, 36, 51 52 0110V49647-52_EN(UCA) 52 1/11/0, 10:37 AM LIST OF MANUFACTURER’S CODES LISTES DES CODES FABRICANT Elin Elta Emerson 1001 0331 0001, 0021, 0061, 0071, 0081, 0091, 0111, 0811, 0821, 0831, 0841, 0851, 0861, 0871, 0901, 0921, 0941, 0981, 1011, 1031, 1051, 1081, 1091 Envision 0361, 1111 Erres 1001 Etron 0331 Ferguson 1001 Finlux 1001 Fisher 0171, 0801, 0981 Formenti 0441 Formonti 1001 Fortress 1141 Fujitsu 1091 Funai 1051, 1091, 1341, 1361, 1411, 1451, 1501, 1521 Futuretech 1051 GE 0131, 0161, 0201, 0751, 0761, 0771, 0781, 0791, 0811, 0861, 1041 GEC 0271, 1001 Gemini 0391 Genexxa 0431 Gibralter 0891, 1031, 1111 GoldStar 0031, 0121, 0351, 0411, 0731, 0741, 0861, 0941, 0971, 1001, 1031, 1111, 1151 Goodmans/Tashiko 0271, 0661, 1001 Granada 1001 Grundig 1781, 1791, 1801, 1811, 1821, 1831, 1841, 1851, 1861, 1871, 1881 Gunpy 1051, 1091 H/K 0721 Hallmark 0861 Hanseatic 1001 Harvard 1051, 1061 Hinari 1001, 1091 Hitachi 0181, 0351, 0671, 0681, 0691, 0701, 0711, 0871, 0941, 0971, 1351 Hypson 1001 Ima 1051 Indiana 1001 Infinity Reference 0101 Interfunk 1001 ITT 0611 Janeil 1131 JBL 0101 JCB 0951 Jensen 0311 Jinxing 1531, 1541, 1551, 1561, 1571, 1621, 1631, 1641, 1651, 1691, 1731 JVC 0261, 0281, 0641, 0651, 0661, 0841 Kawasho 0901 TV A-Mark A Tandy Abex Admira Adventura Aiko Akai Alba Alleron Ambassador Amstrad Anam 1161 0941 1151 1141 1131 1121 0331, 1101, 1111 0431 1091 1081 0481, 1081 0251, 1041, 1051, 1061, 1071 Anam National 1041 AOC 0361, 1021, 1031, 1111, 1161 Archer 1161 Audiosonic 1001 Audiovox 1051, 1161 Awai 1481 Bauer 0441 Baur 1001 Beijing 1511, 1551, 1561 Belcor 1031 Bell & Howell 0981, 0991 Beon 1001 Bradford 1051 Brockwood 1031 Broksonic 1161 Bush 1001 Candle 0351, 0361, 0961, 0971, 1111, 1131 Capehart 1021 Carver 0101 Cathay 1001 Celebrity 0951 Centurion 0411 Changhong 1541, 1551, 1561, 1621 Citizen 0351, 0361, 0921, 0931, 0941, 0961, 0971, 1111, 1121, 1131 Clairtone 1011 Clarivox 1001 Concerto 0351, 0971 Conrowa 1751 Contec 0901, 0911, 1011, 1051 Corando 0941 Craig 0251, 1051 Crown 0941, 1051 Curtis Mathes 0161, 0361, 0931, 0941, 0981, 1111 CXC 1051 Daewoo 0291, 0301, 0331, 0721, 0941, 1001, 1031, 1121, 1191, 1531, 1581, 1591, 1601 Dansai 1001 Daytron 0941, 1031 Decca 0271, 1001 Dixi 0331, 1001, 1071 Dumont 0891, 1031 Dynatech 0881 Electroband 0951, 1011 Electrohome 0941 Electron 0941 Kaypani Kenwood Kloss KTV 1021 0361, 1031, 1111 0631, 0721, 1131 0921, 0941, 1011, 1051, 1111 Leyco 1001 Liesenk & Tter 1001 Lloytron 0941 Loewe 1001 Logik 0991, 1771 Luxman 0351, 0971 Lxi 0101, 0621, 0761, 0861, 0981 Magnavox 0101, 0341, 0391, 0401, 0411, 0421, 0581, 0591, 0601, 0611, 0631, 0661, 0961, 1111 Majestic 0991 Marantz 0101, 0221, 0361, 1001, 1111 Mark 1001 Matsui 0271, 0331, 1001 Mediator 1001 Megatron 0691, 0861, 1161 MEI 1011 M Electronic 1001 Memorex 0331, 0571, 0861, 0971, 0981, 0991, 1771 Metz 1791, 1831, 1891, 1901, 1911, 1921, 1931, 1941 MGA 0361, 0561, 0571, 0861, 1031, 1111 Midland 0751, 0761, 0891, 0941, 1151 Mitsubishi 0221, 0321, 0561, 0571, 0661, 0861, 1031, 1101, 1381 Montgomery 1091 Motorola 1041, 1141 MTC 0351, 0361, 0881, 0931, 0971, 1011, 1031, 1111 Multitech 0881, 1051 NAD 0551, 0621, 0861 NEC 0241, 0351, 0361, 0661, 0971, 1031, 1111, 1321, 1711 Neckermann 1001 Nei 1001 Nikkai 0271, 0431, 1001, 1151 Nikko 0861, 1111, 1121 Novabeam 0721 NTC 1121 Onwa 1051 Optimus 0551 Optonica 0541, 1141 Orion 0831, 1001 Osaki 0271, 1151 Otto Versand 1001 Panasonic 0101, 0191, 0251, 0751, 1041, 1311, 1371, 1431 Panda 1541, 1721 Penny Peony Philco Philips Phonola Pilot Pioneer Portland Priceclub Prism Proscan Protech Proton Pulsar Pulser Quasar Quelle Radio Shack Radiola RCA Realistic Rhapsody R-line Runco Saisho Sampo Samsung Samsux Sanyo SBR Schneider Scimitsu Scotch Scott Sears Shanghai Sharp Shogun Signature 0161, 0361, 0521, 0531, 0621, 0731, 0751, 0761, 0781, 0791, 0861, 0931, 0941, 1031, 1041, 1111, 1151, 1161 1561, 1621 0361, 0581, 0591, 0601, 0611, 0631, 0961, 1031, 1111 0101, 0401, 1001 1001 0941, 1031, 1111 0511, 0551, 0871, 1331 0941, 1031, 1121 0931 0751 0761 1001 0501, 0861, 0941, 1021, 1161 0891 1031 0251, 0751, 1041 1001 0541, 0941, 1031, 1051, 1151 1001 0051, 0141, 0151, 0181, 0411, 0491, 0531, 0761, 0771, 0871, 1031 0541, 0861, 0941, 0971, 0981, 1031, 1051, 1111, 1151 1011 1001 0891, 1111 0331, 1081 0361, 0941, 1021, 1111, 1151 0331, 0341, 0351, 0361, 0861, 0931, 0941, 0971, 1001, 1031, 1111, 1151, 1461 0941 0171, 0231, 0271, 0661, 0801, 0911, 0981, 1231, 1251, 1261 1001 1001 1031 0861 0831, 0861, 0941, 1031, 1051, 1091 0101, 0161, 0171, 0351, 0481, 0521, 0621, 0761, 0801, 0861, 0971, 0981, 1091 1561, 1681 0461, 0471, 0541, 0661, 0911, 0941, 1141, 1241, 1271 1031 0991, 1771 i 03V496code(UCA) 1 1/11/0, 1:07 PM Simpson Solavox Sonoko Sontec Sony 0581, 0961 1151 1001 1001 0371, 0451, 0661, 0841, 0951, 1281, 1441 Soundesign 0861, 0961, 1051, 1091 Soundwave 1001 Spectricon 1161 Squareview 0481 SSS 1031, 1051 Star-lite 1051 Suprem 0951 Supre-macy 1131 Surpa 0351, 0971 Sylvania 0101, 0361, 0441, 0581, 0591, 0601, 0611, 0631, 0961, 1111 Symphonic 0481 Sysline 1001 Tandy 0271, 0431, 1141 Tatung 0271, 0881, 1001, 1041, 1161 Tcl 1561, 1631, 1701 Technics 0751 Techwood 0351, 0751, 0971 Teknika 0101, 0351, 0571, 0931, 0941, 0961, 0971, 0991, 1031, 1051, 1091, 1121, 1131, 1771 Teletech 0331 Tera 0501 Thakral 1671 Thorm 1001 TMK 0351, 0861, 0971, 1081 Toshiba 0381, 0521, 0621, 0661, 0931, 0981, 1301 Tosonic 1011 Totevision 0941 Trical 0911 Universal 0781, 0791 Universum 1001 Vector Research 0361, 1111 Vestel 1001 Victor 0651, 1201, 1211, 1221 Video Concept 1101 Vidikron 0101, 0211 Vidtech 0861, 1031 Viking 1131 Wards 0101, 0361, 0451, 0541, 0581, 0591, 0601, 0611, 0771, 0781, 0791, 0861, 0971, 0991, 1031, 1091, 1111, 1771 Watson 1001 Xogego 1611, 1621, 1661, 1741, 1761 Yamaha 0221, 0361, 0571, 1031, 1111, 1141, 1381 Yoko 1001 Zenith 0011, 0041, 0891, 0991, 1771 Zonda 1161 CABLE ABC 0256, 0376 Antronix 0136 Archer 0136, 0286 BBT 0076 Cabletime 0166 Cablevision 0196 Colour Voice 0306, 0346 Comtronics 0216, 0276 Eagle Comronics 0276 Eastern 0066 Electricord 0206 Electus 0266 GE 0116, 0126 GEC Cable System 0196 Hamlin H5 0676 Hamlin H6 0666 Hamlin H6S 0656 Hamlin H8 0646 Hamlin H9 0636 Jerrold 0256 Jerrold 400L 0626 Jerrold 450L 0616 Jerrold 550 0606 Jerrold Osd Catv 0596 Jerrold Sprucer 0436 Magnavox/Philips 0416, 0426 Mamm 0296 Memorex 0386 Movie Time 0146, 0206 Northcoast 0016 NSC 0146 Oak 0106 Oak Sigma 450 0546 Oak Sigma 550 0536 Panasonic TZ 120/130 0476 Panasonic TZ 170/180 0446 Panasonic TZ140 0466 Panasonic TZ150/160 0456 Paragon 0386 Philips 0036, 0216, 0306, 0316, 0326, 0336, 0346 Pioneer 0006, 0086 Pioneer BR50 0846 Pioneer BR60/70/80/81/82 0696 Pioneer BR90 0556 Pulsar 0386 RCA Digital Satellite System 0396, 0406 Realistic 0136 Regency/Eastern 0686 Runco 0386 Samsung 0276 Scientific Atlanta 175/475 0576 Scientific Atlanta 75 0366, 0586 Scientific Atlanta 8650 0566 Signal 0276 SL Marx 0276 Spectavision 0236 Standard Components 0186 Starcom V 0256 Stargate 0276 Sylvania/Texscan 0376, 0496 Teknika 0176 Teleservice 0056 Teleview 0276 Texscan 0186, 0376 TFC 0026 Tocom 0226, 0356 Tocom 5503A 0526 Tocom 5503VIP/5507 0516 Tocom TC56 0506 Toshiba 0386 Tudi 0046 Unika Universal Videoway Viewstar Zenith 0136 0136, 0156, 0206, 0286 0096 0216 0246, 0386, 0486 SATELLITE TUNER Alpha Star 0826 Chaparral 0756 Echostar 0836 General Instrument 0776 HTS 0836 Hughes Network Systems 0816 Jerrold 0776, 0786 Panasonic 0806 Primestar 0776, 0786 RCA 0766 Sony 0796 VCR A Tandy Adventura Aiko Aiwa Akai 0902 0992 0982 0992 0262, 0942, 0952, 0962, 0972 American High 0932 Amstrad 0992 ASA 0002, 0912 Asha 0922 Audio Dynamics 0202 Audiovox 0912 Beaumark 0922 Bell & Howell 0902 Blaupunkt 0412 Broksonic 0872, 0882, 0892 Bush 0852 Calix 0912 Canon 0862, 0932 CCE 0852, 0982 Citizen 0912, 0982 Colt 0852 Craig 0832, 0842, 0852, 0912, 0922 Curtis Mathes 0662, 0822, 0932 Cybernex 0922 Daewoo 0802, 0812, 0982 DBX 0202 Dynatech 0472, 0992 Electrohome 0912 Electrophonic 0912 Emerex 0792 Emerson 0072, 0132, 0142, 0152, 0162, 0172, 0182, 0192, 0212, 0702, 0712, 0722, 0732, 0742, 0752, 0762, 0772, 0782, 0872, 0882, 0892, 0912, 0952, 0992, 1072 Finlux 0002, 0992 Fisher 0682, 0692, 0842, 0902 Fuji 0672, 0932 Funai 0992 Garrard 0992 GE 0662, 0822, 0932 Go Video 0642, 0652 GoldStar 0082, 0632, 0912 Goodmans 0402 Gradiente 0992 Granda 0612, 0902 Grundig 0002 H/K 1082 ii 03V496code(UCA) 2 1/11/0, 1:07 PM Harley Davidson 0992 Harmon/Kardon 0632, 1082 Harwood 0752, 0852 Headquarter 0612 HI-Q 0842 Hinari 0852 Hitachi 0102, 0562, 0572, 0582, 0592, 0602, 0992 ITT 0942 JVC 0202, 0522, 0532, 0542, 0552 Kenwood 0202, 0542, 0612, 0632, 0902 KLH 0852 Kodak 0912, 0932 Lloyd 0992 Logik 0852 Luxor 0942 LXI 0022, 0912 Magnavox 0002, 0482, 0492, 0502, 0512, 0932 Magnin 0922 Marantz 0002, 0202, 0402, 0632, 0932 Marta 0912 Matsui 0722 Matsushita 0932 MEI 0222, 0932 Memorex 0232, 0242, 0472, 0512, 0612, 0842, 0902, 0912, 0922, 0932, 0992 MGA 0762, 0952 MGA Technology 0922 Minolta 0592, 0602 Mitsubishi 0452, 0462, 0542, 0762, 0952, 1082 Motorola 0472, 0932 MTC 0922, 0992 Multitech 0852, 0992 NAD 0442 NEC 0122, 0202, 0292, 0422, 0432, 0542, 0632 Nikko 0912 Noblex 0922 Olympus 0412, 0932 Optimus 0442, 0472, 0912 Optonica 0402 Orion 0212, 0722, 0742, 0772 Osaki 0912 Panasonic 0012, 0052, 0092, 0222, 0372, 0382, 0392, 0412, 0932 Penny 0202, 0432, 0602, 0632, 0692, 0912, 0922, 0932 Pentax 0592, 0602 Perdio 0992 Philco 0002, 0932 Philips 0002, 0282, 0402, 0492, 0932 Pilot 0912 Pioneer 0442, 0542 Proscan 1002, 1012, 1022, 1032, 1042, 1052, 1062 Pulsar 0512 Quarter 0612 Quartz 0272, 0612 Quasar 0382, 0392, 0932 Radio Shack 0912, 0992 Radix 0912 Randex 0912 RCA 0112, 0382, 0392, 0482, 0592, 0602, 0662, 0822, 0942 Realistic 0402, 0472, 0612, 0682, 0842, 0902, 0912, 0922, 0932, 0992 Ricoh 0352, 0362 Saisho 0212, 0582, 0722, 0732, 0742, 0772 Salora 0612, 0762 Samsung 0212, 0312, 0922, 0962 Sanky 0472, 0512 Sansui 0292, 0542, 0832 Sanyo 0242, 0612, 0842, 0902, 0922 SBR 0002, 0282 Schneider 0852 Scott 0342, 0712, 0762, 0872, 0882, 0892 Sears 0302, 0592, 0602, 0612, 0682, 0692, 0842, 0902, 0912, 0932 Sharp 0402, 0472 Shintom 0852 Shogun 0922 Singer 0852 Sony 0032, 0332, 0352, 0362, 0672, 0792, 0932 STS 0602 Sunpak 0352 Sylvania 0002, 0492, 0502, 0762, 0932, 0992 Symphonic 0992 Tandy 0992 Tashiko 0712, 0992 Teac 0992 Technics 0932 Teknika 0322, 0912, 0932, 0992 Telefunken 0252 TMK 0212, 0732, 0772, 0922 Toshiba 0062, 0302, 0342, 0622, 0682, 0712, 0762 Totevision 0912, 0922 Unitech 0922 Vector Research 0202, 0432, 0632 Victor 0532, 0542, 0552 Video Concepts 0202, 0432, 0632, 0952 Wards 0322, 0402, 0472, 0482, 0602, 0712, 0842, 0852, 0922, 0932, 0992 Yamaha 0202, 0632, 0762 Zenith 0042, 0362, 0512, 0672 LD PLAYER Aiwa Denon Disco Vision Funai Hitachi (E) Kenwood Magnavox Marantz Mitsubishi NAD Panasonic Philips Pioneer RCA Realistic Sharp Sony Victor Yamaha CD PLAYER Acoustic Research 1295 ADC 0025, 0065 Adcom 0205, 0255, 1015 ADS 0265 Aiwa 0295, 0945, 1035, 1055 Akai 0175, 0485, 0535 Alpine 1215, 1305 Audio-Technica 0545 BSR 0245, 0655, 0775 California Audio Lab 0055 Capetronic 1205 Carrera 0245 Carver 0285, 1135 Casio 0345 Crown 0185 Curtis Maths 0345 Denon 0275, 0875, 0885 Deual (E) 0505 Dynamic Bass (H) 0555 Emerson 0205, 0325, 1105 Eroica 1275 Fisher 0095, 0555, 0925, 1005 Garrard 0365 Genexxa 0305, 0325, 1105 GoldStar 1225, 1265, 1135, 1335 H/K 0105, 0175, 0465, 0995 Hitachi 0195, 0505, 0205, 0815 Inkel 0115, 0395 JVC 0315 Kenwood 0045, 0095, 0405, 0585, 0725, 0735, 0745, 0755, 0895 Kyocera 0025 Luxman 0075, 0425, 0675, 0705, 0715, 0985 Magnavox 0165, 0215, 0645, 0955 Marantz 0215, 0235, 0375, 0785, 1345 McIntosh 0355, 1085 MCS 0905, 1315 Memorex 0205, 0225, 0235, 0305, 0325, 1105 DVD PLAYER Akai JVC Onkyo Panasonic Philips Pioneer Samsung Sharp Sony Toshiba Yamaha 0157 0147 0017 0157 0017 0087, 0107 0027 0027 0137 0137 0077, 0177 0027 0037, 0017, 0137 0167 0157 0127 0047, 0057, 0117 0097 0007, 0067 0108 0168 0128 0048 0188 0208, 0228 0148 0068 0028 0088 0008, 0048 MGA Mission Mitsubishi MTC NAD 0135 0215 0135, 0445 1255 0035, 0615, 0685, 0695 Nakamichi 0125, 0435, 0515 NEC 0255, 0905, 0965 Nikko 0545, 1005 Onkyo 0155, 0455, 0495, 0805, 1155 Optimus 0225, 0245, 0555, 0595, 0845, 0855, 0865, 0895, 0935 Panasonic 0055, 0825, 1095, 1125 Penny 0905 Philips 0165, 0215 Pioneer 0305, 0935, 1045 Proton 0215, 1185 Quasar 0055 RCA 0205, 0915, 1115 Realistic 0205, 0225, 0235, 0325, 0555, 0845 Revox 1175 Rotel 0215 Saba Telecommander (E) 0505 SAE 0215 Samsung 1285 Sansui 0215, 0625, 0975, 1025, 1105 Sanyo 0145, 0555, 0635, 0765 Scott 0325, 1105 Sears 0345 Sharp 0235, 0665, 0895, 1065, 1075 Sherwood 0115, 0235, 0395, 0475 Siements Garrard 1245 Signature 0175 Sontec 1165 Sony 0065, 0565, 0865, 1145 Staron 1235 STS 0025 Sylvania 0215 Symphnoic 0335 Tandy 0305 Tangberg 1195 Teac 0235, 0335, 0385, 0525, 0795, 0835, 1355 Technics 0055, 0605, 1095 Techwood 1325 Telefunken (E) 0505 Thomson (E) 0505 Toshiba 0035, 0685 Vector Research 0065, 1135 Victor 0315 Wards 0175 Yamaha 0005, 0015, 0575, 1065 TAPE DECK Aiwa Akai Carver Denon Fisher Garrard JVC Kenwood Magnavox Marantz Mitsubishi Onkyo Optimus Philips Pioneer Revox Sansui Sharp Sherwood Sony Teac Technics Victor Wards Yamaha 0094, 0214, 0224 0184 0094 0304 0144 0194, 0204 0274, 0284, 0294 0124, 0134, 0154, 0234, 0244, 0264 0094 0094, 0344 0184 0364, 0374 0034, 0064, 0204, 0334 0094 0034, 0044, 0064 0354 0094, 0344 0264 0334 0054, 0084, 0324 0194, 0254 0074, 0314 0294 0034 0004, 0014 MD RECORDER Yamaha 0024 iii 03V496code(UCA) 3 1/11/0, 1:07 PM UCA RX-V496 Natural Sound AV Receiver Ampli-tuner audio-vidéo YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA 00RX-V496(UCA)-cv1/4 1 OWNER’S MANUAL MODE D’EMPLOI Printed in Malaysia ID V502840-2 9/28/0, 4:37 PM Quick Reference Card TAPE/MD AMP(TUNER) POWER A/B/C/D/E TEST POWER Input selector buttons Input selector buttons Input selector buttons Input selector buttons EFFECT PRESET+/– EFFECT EFFECT DISC SKIP+/– EFFECT DISC SKIP+/– VOLUME TV VOLUME SLEEP MUTE SLEEP TV INPUT PRG+, PRG– REC/PAUSE PLAY DIR A (TAPE) SKIP– (MD) SET MENU REWIND (TAPE) SEARCH (MD) +/– TIME LEVEL DVD/LD POWER POWER VOLUME MUTE CD VOLUME TV VOLUME MUTE VOLUME TV VOLUME DISPLAY (MD) SLEEP DECK A/B (TAPE) DISPLAY TV INPUT PAUSE (MD) PAUSE DIR B (TAPE) SKIP+ (MD) PLAY SKIP– FAST FORWARD (TAPE) SEARCH (MD) SEARCH STOP SKIP+ SEARCH STOP MUTE SLEEP PLAY SKIP– SEARCH TV VOLUME DISPLAY TV INPUT PAUSE SKIP+ SEARCH STOP V503030 Quick Reference Card VCR DVD MENU VCR POWER POWER DISC SKIP+/– VOLUME MUTE RETURN MENU SELECT MENU LEFT TITLE CBL/SAT TV CBL/SAT POWER TV POWER Numeric buttons CHANNEL CHANNEL CHANNEL CLEAR +10 EFFECT CHANNEL CBL/SAT ENTER CHANNEL+/– +100 CHANNEL ENTER EFFECT CHANNEL ENTER VCR CHANNEL+/– VOLUME TV VOLUME MUTE INDEX TV INPUT MENU UP TV SLEEP *1 VCR REC VCR PLAY MENU RIGHT MENU MENU DOWN VCR REWIND VOLUME TV VOLUME DISPLAY TV INPUT MUTE TV SLEEP TV CHANNEL+/– VOLUME TV VOLUME TV MUTE DISPLAY TV INPUT VCR PAUSE MENU SELECT MENU LEFT MENU UP VCR FAST FORWARD MENU VCR STOP RECALL *1 Press this button twice to start recording. Appuyer deux fois sur cette touche pour commencer l’enregistrement. Drücken Sie diese Taste zweimal, um die Aufnahme zu starten. Tryck två gånger på den här knappen för att börja spela in. TV SLEEP *1 VCR REC VCR PLAY TV VOLUME DISPLAY TV INPUT VCR PAUSE MENU RIGHT VCR REWIND MENU DOWN Premere due volte questo tasto per iniziare la registrazione. Presione dos veces este botón para empezar a grabar. Druk tweemaal op deze toets om met opnemen te beginnen. VCR FAST FORWARD VCR STOP V503030