TomTom Trucker de handleiding

Categorie
Auto navigatiesystemen
Type
de handleiding

Deze handleiding is ook geschikt voor

TomTom TRUCKER
Reference Guide
2
Contents
Welcome to navigation with TomTom 6
Get going 7
Installing in your car .............................................................................................. 7
Positioning the device ............................................................................................ 7
Switching on and off .............................................................................................. 7
Safety Notice ....................................................................................................... 8
Setting up ........................................................................................................... 8
GPS reception ...................................................................................................... 8
Sending information to TomTom ................................................................................ 8
Memory card slot .................................................................................................. 9
Device not starting ................................................................................................ 9
Charging your device .............................................................................................. 9
Caring for your TRUCKER ......................................................................................... 9
Connecting to TomTom services 10
About TomTom services ........................................................................................ 10
Always connected devices ...................................................................................... 10
What's on the screen 11
The map view..................................................................................................... 11
The guidance view ............................................................................................... 12
The route bar ..................................................................................................... 14
Distances and the route bar ............................................................................... 15
The quick menu .................................................................................................. 15
Navigation buttons............................................................................................... 15
Other buttons ..................................................................................................... 17
Volume control ................................................................................................... 19
Using gestures .................................................................................................... 19
Changing the text and button size ............................................................................ 20
Reordering the Main Menu buttons ........................................................................... 20
Traffic 21
About TomTom Traffic .......................................................................................... 21
About RDS-TMC ................................................................................................... 21
The route bar ..................................................................................................... 21
Looking at traffic on the map ................................................................................. 22
Looking at traffic on your route ............................................................................... 23
Traffic incidents ................................................................................................. 24
Advanced Lane Guidance ....................................................................................... 25
Time-dependent speed limits ................................................................................. 25
Setting your vehicle type 27
About My Vehicle ................................................................................................ 27
Setting your vehicle type ....................................................................................... 27
Planning a route for a Bus or Truck .......................................................................... 28
Viewing route restrictions ...................................................................................... 28
3
Syncing TomTom MyDrive 30
About TomTom MyDrive ........................................................................................ 30
Logging in to your MyDrive account .......................................................................... 30
Showing a planned destination in MyDrive .................................................................. 30
Finding and syncing locations using MyDrive ................................................................ 30
Syncing My Places locations with MyDrive ................................................................... 31
Importing a community POI list ............................................................................... 31
Deleting a community POI list ................................................................................. 31
Saving and restoring your personal navigation information .............................................. 32
Using Quick Search 33
About search ...................................................................................................... 33
Planning a route to a POI using search ....................................................................... 33
Planning a route to a POI using online search .............................................................. 35
Entering search terms ........................................................................................... 37
Working with search results ................................................................................... 38
About postcodes ................................................................................................. 40
About mapcodes ................................................................................................. 40
List of POI type icons ............................................................................................ 40
Planning a route 45
Planning a route to an address using search ................................................................ 45
Planning a route to a city centre ............................................................................. 47
Planning a route to a POI using search ....................................................................... 48
Planning a route to a POI using online search .............................................................. 50
Planning a route using the map ............................................................................... 52
Planning a route using My Places ............................................................................. 53
Planning a route using coordinates ........................................................................... 55
Planning a route using a mapcode ............................................................................ 56
Finding an alternative route ................................................................................... 57
Planning a route in advance ................................................................................... 57
Finding a car park ............................................................................................... 59
Finding a petrol station ......................................................................................... 61
Changing your route 64
The Current Route Menu ....................................................................................... 64
Avoiding a blocked road ........................................................................................ 65
Types of route .................................................................................................... 66
Route features ................................................................................................... 66
Adding a stop to your route from the current route menu ............................................... 66
Adding a stop to your route using the map ................................................................. 67
Deleting a stop from your route ............................................................................... 67
Reordering stops on a route ................................................................................... 67
My Routes 68
About My Routes ................................................................................................. 68
Saving a route .................................................................................................... 68
Navigating using a saved route ................................................................................ 69
Adding a stop to a saved route using the map .............................................................. 69
Deleting a route from My Routes .............................................................................. 70
4
Voice control (Speak&Go) 71
About voice control.............................................................................................. 71
Starting voice control ........................................................................................... 71
Making your own wake-up phrase ............................................................................. 71
The voice control screen ....................................................................................... 72
Some tips for using voice control ............................................................................. 73
What you can use voice control for........................................................................... 73
Saying commands in different ways .......................................................................... 73
Entering an address using voice control ..................................................................... 74
Going to home using voice control ........................................................................... 74
Going to a POI using voice control ............................................................................ 75
Changing a setting using voice control ....................................................................... 75
Map Share 76
About Map Share ................................................................................................. 76
Creating a map correction report ............................................................................. 76
Creating a map correction report from a marked location ............................................... 77
Types of map correction ........................................................................................ 78
Speed Cameras 80
About speed cameras ........................................................................................... 80
Crossing into another area or country ....................................................................... 80
Speed camera warnings ......................................................................................... 80
Changing the way you are warned ............................................................................ 82
Reporting a new speed camera ............................................................................... 82
Confirm or remove a mobile speed camera ................................................................. 83
Updating locations for cameras and hazards ............................................................... 83
Danger Zones 84
About danger zones and risk zones ........................................................................... 84
Crossing into another area or country ....................................................................... 84
Danger zone and risk zone warnings ......................................................................... 85
Changing the way you are warned ............................................................................ 85
Reporting a risk zone ............................................................................................ 86
Updating locations for danger zones and risk zones ....................................................... 86
My Places 87
About My Places .................................................................................................. 87
Setting your home and work locations ....................................................................... 87
Changing your home location .................................................................................. 88
Adding a location from My Places ............................................................................. 89
Add a location to My Places from the map .................................................................. 89
Adding a location to My Places using search ................................................................ 90
Adding a location to My Places by marking ................................................................. 90
Deleting a recent destination from My Places .............................................................. 90
Deleting a location from My Places ........................................................................... 90
Settings 91
My Vehicle ......................................................................................................... 91
Appearance ....................................................................................................... 91
Display ......................................................................................................... 92
Route Bar ...................................................................................................... 92
5
Guidance view ................................................................................................ 94
Automatic Zoom.............................................................................................. 94
Voices .............................................................................................................. 95
Voice Control ..................................................................................................... 95
Maps ................................................................................................................ 96
Route Planning ................................................................................................... 96
Sounds and Warnings ............................................................................................ 97
Warning type ................................................................................................. 97
Speed camera warnings ..................................................................................... 97
Safety warnings .............................................................................................. 97
Screen touch sounds ......................................................................................... 98
Read aloud traffic warnings ................................................................................ 98
Language and Units .............................................................................................. 98
System ............................................................................................................. 99
Help ................................................................................................................ 99
Getting Help 101
Help ............................................................................................................... 101
Product certification 102
Finding product certification information on your device ............................................... 102
Updating using MyDrive Connect 103
About MyDrive Connect ........................................................................................ 103
MyTomTom account ............................................................................................ 103
Setting up MyDrive Connect ................................................................................... 103
Addendum 105
Copyright notices 110
6
This Reference Guide explains all you need to know about your new TomTom TRUCKER.
If you want a quick read of the essentials, we recommend that you read the Get going chapter. This
covers installation, switching on, setting up and planning your first route.
After that, you will probably want to connect to TomTom services and you can read all about that in
the Connecting to TomTom services chapter. To help you avoid traffic delays and get to your
destination quicker, you can use TomTom services even on the routes you drive every day.
For information about what you see on the screen, go to:
What's on the screen
Using gestures
Main menu
Tip: There are also frequently asked questions (FAQs) at tomtom.com/support. Select your
product model from the list or enter a search term.
We hope you enjoy reading about and, most importantly, using your new TRUCKER!
Welcome to navigation with TomTom
7
Installing in your car
Use the supplied mount to install your TomTom TRUCKER in your vehicle. Read the instructions
about positioning your device before you install your TRUCKER.
To install your TRUCKER, do the following:
1. Connect the supplied USB cable to the mount. If the mount is integrated into your TRUCKER,
connect the USB cable to the device.
Note: Use ONLY the USB cable supplied with your TRUCKER. Other USB cables may not work.
2. Connect the USB cable to the USB car charger and plug this into the power supply on your
dashboard.
3. Choose the best smooth location, on your windscreen or side window, to mount your TomTom
TRUCKER.
Tip: If the mount is integrated into your TRUCKER, you can easily change the rotation of your
device. Push the button on the back of the device to release the mount, then slide the mount
out. Insert it back into the other side of the device.
4. Make sure that both the suction cup on the mount and your windscreen are clean and dry.
5. Press the suction cup of the mount firmly against your windscreen.
6. Turn the rubber grip near the base of the mount in a clockwise direction until you feel it lock.
7. If your mount is not integrated into your TRUCKER, place your TRUCKER in the mount, making
sure that it clicks into place.
Dashboard mount disks are available as part of a range of accessories for your TRUCKER. For more
information, go to tomtom.com/accessories.
Positioning the device
Be careful where you install your TRUCKER. The TRUCKER shouldn't block or interfere with any of
the following:
Your view of the road.
The controls in your vehicle.
Your rear-view mirrors.
The airbags.
You should be able to reach your TRUCKER easily without leaning or stretching. In a car, you can
attach your TRUCKER to the windscreen or side window or you can use a Dashboard Mount Disk to
attach the mount to your dashboard.
Switching on and off
Switching your device on
Press the On/Off button until your device starts. If the device was off you see the map view. If your
device was sleeping you see the last screen you were looking at.
Sending your device to sleep
To send your navigation device to sleep, press the On/Off button and then release it.
Get going
8
You can also press the On/Off button for more than 2 seconds until you see the Sleep and Turn Off
buttons. Select Sleep to make the device sleep.
Tip: To send your navigation device to sleep when the USB cable is unplugged or whenever it is
removed from the mount, go to Battery settings in the Settings menu.
Switching your device off completely
To switch off your navigation device completely, you can do one of the following:
Press and hold the On/Off button for more than 2 seconds until you see the Sleep and Turn Off
buttons. Select Turn Off to switch off the device. Select the "back" button if you don't want to
switch your device off.
Press and hold the On/Off button for more than 5 seconds until the device switches off.
Safety Notice
Some navigation devices contain a GSM/GPRS module which can interfere with electrical devices
such as cardiac pacemakers, hearing aids and aviation equipment.
Interference with these devices may endanger the health or life of you or others.
If your device includes a GSM/GPRS module, do not use it near unprotected electrical units or in
areas where the use of mobile telephones is prohibited, such as hospitals and aircraft.
Setting up
Note: The language you choose will be used for all text on the screen. You can always change the
language later in Language and Units in the Settings menu.
When you first switch on your TomTom TRUCKER, you have to answer a few questions to set it up.
Answer the questions by touching the screen.
GPS reception
When you first start your TomTom TRUCKER, it may need a few minutes to determine your position.
In future, your position will be found much faster.
To ensure good satellite reception, use your TRUCKER outdoors and keep it upright. Large objects
such as tall buildings can sometimes interfere with reception.
Important: QuickGPSfix contains information about satellite positions which helps your TRUCKER
find your position faster. QuickGPSfix information is sent to Always Connected devices in real time
and to Smartphone Connected devices when connected to TomTom services using your smartphone.
You can also update QuickGPSfix using MyDrive.
Sending information to TomTom
When you first start navigating or you have reset your TRUCKER, your TRUCKER asks for permission
to collect some information about your use of the navigation device. The information is stored on
your TRUCKER until we retrieve it. We use it anonymously to improve our products and services. If
you use our services, we will also use your location information to deliver the services to you.
You can change whether you send this information with us at any time by doing the following:
1. In the Main Menu, select the Settings button.
2. Select System.
3. Select Your information.
4. Select the button to turn sending of information on or off.
9
Note: If you choose not to send location information to us, you will no longer receive our
services. This is because services need to send the location of your device to TomTom in order to
receive the traffic information related to where you are. The end date of your subscription
remains the same, even if you do not send this information to us.
Additional information
If you think that your information is not being used for the purpose for which you have provided it
to TomTom, contact us at tomtom.com/support.
You can find current and more detailed information at tomtom.com/privacy.
Memory card slot
Some TomTom navigation devices have a memory card slot that is located on the side or bottom of
the device.
Before you use the memory card slot, make sure that you have the latest version of the application
installed on your navigation device by connecting to MyDrive using a computer.
When your TRUCKER is up-to-date, you can use a memory card as extra storage space to add extra
maps, tracks or routes to your device. Maps can be purchased from tomtom.com.
Device not starting
In rare cases, your TomTom TRUCKER may not start correctly or may stop responding to your taps.
First, check that the battery is charged. To charge the battery, connect your TRUCKER to the car
charger. It can take 3 - 5 hours to fully charge the battery depending on the type of device.
If this does not solve the problem, you can perform a reset. To do this, press and hold the On/Off
button until your TRUCKER begins to restart.
Charging your device
The battery in your TomTom TRUCKER charges when you connect it to the car charger, to your
computer or to a USB Home Charger.
You are warned when the battery level is low or critical. You lose your connection to some TomTom
services when the battery level is low or critical. When the battery is empty, your TRUCKER goes
into sleep mode.
Note: Use ONLY the USB cable supplied with your TRUCKER. Other USB cables may not work.
Caring for your TRUCKER
It is important to take care of your device:
Do not open the casing of your device under any circumstances. Doing so may be dangerous and
will invalidate the warranty.
Wipe or dry the screen of your device using a soft cloth. Do not use any liquid cleaners.
10
About TomTom services
TomTom services give you real-time information about traffic and speed cameras on your route. To
get TomTom services on your TRUCKER you need to be logged in to a MyTomTom account and have
active subscriptions to TomTom Traffic and TomTom Speed Cameras.
Your TRUCKER has a permanent connection directly to TomTom services. These navigation devices
are called 'Always Connected' devices.
Check tomtom.com/connect for more information.
Note: TomTom services are not available in all countries or regions, and not all services are
available in all countries or regions. For more information on available services in each region, go
to tomtom.com/services.
Always connected devices
Follow these steps to get TomTom services on a TomTom TRUCKER that is always connected:
Note: When you start your TRUCKER for the first time, or after a reset, you are given the option
to activate TomTom services when you set up your TRUCKER.
1. Select TomTom Services in the Main Menu.
2. If you are prompted, select Yes to agree to send information to TomTom.
Note: You cannot use TomTom services unless you agree to send information to TomTom.
3. Select Traffic & Speed Cameras.
4. Create a new MyTomTom account or login to your existing MyTomTom account.
Tip: If you already own a TomTom navigation device, we recommend that you open a new
MyTomTom account for your TRUCKER using a different email address.
TomTom services are now active.
Connecting to TomTom services
11
The map view
The map view is shown when you have no planned route. Your actual location is shown as soon as
your TRUCKER has found your GPS location.
You can use map view in the same way as you might look at a traditional paper map. You can move
around the map using gestures, and zoom using the zoom buttons.
Important: Everything on the map is interactive including the route and the map symbols - try
selecting something and see what it does!
Tip: To open a pop-up menu for an item on the map, for example a route or a POI, select the
item to open the menu. To select a location on the map, select and hold the location until the
pop-up menu opens.
The map shows your current location and many other locations such as your My Places locations.
If you have not planned a route the map is zoomed out to show the area around your location.
If you have planned a route, your complete route is shown on the map. You can add stops to your
route directly from the map. When you start to drive, the guidance view is shown.
What's on the screen
12
1. Back button. This button returns the map to an overview of your whole route or, if no route is
planned, moves the map to put your current location at the centre.
2. Switch view button. Select the switch view button to change between the map view and the
guidance view. When in map view, if you are driving, the small arrow rotates to show you your
current driving direction, with north being up.
3. Zoom buttons. Select the zoom buttons to zoom in and out.
4. Current location. This symbol shows your current location. Select it to add it to My Places or
search near your current location.
Note: If your TRUCKER cannot find your location using GPS or other methods, the symbol
appears grey.
5. Selected location. Press and hold to select a location on the map. Select the pop-up menu
button to show options for the location, or select the drive button to plan a route to the loca-
tion.
6. Main Menu button. Select the button to open the Main Menu.
7. Map symbols. Symbols are used on the map to show your destination and your saved places:
Your destination.
Your home location. You can set your home location in My Places.
A stop on your route.
A location saved in My Places.
Select a map symbol to open the pop-up menu, then select the menu button to see a list of
actions you can take.
8. Traffic information. Select the traffic incident to display information about the traffic delay.
Note: Traffic information is only available if your TomTom TRUCKER has TomTom Traffic.
9. Your route, if you have planned a route. Select the route to clear it, change the route type, add
a stop or save changes to your route.
10. Speed cameras on your route. Select a speed camera to display information about that camera.
11. Route bar. The route bar is shown when you have planned a route.
The guidance view
The guidance view is used to guide you along the route to your destination. The guidance view is
shown when you start driving. You see your current location and details along your route, including
3D buildings in some cities.
Note: 3D buildings in guidance view are not available on all devices.
The guidance view is normally in 3D. To show a 2D map with the map moving in your direction of
travel, change the 2D and 3D default settings.
Tip: When you have planned a route and the 3D guidance view is shown, select the switch view
button to change to the map view and use the interactive features.
13
When your TRUCKER starts after sleeping and you have a route planned, you are shown the guidance
view with your current location.
1. Switch view button. Select the switch view button to change between the map view and the
guidance view.
2. Zoom buttons. Select the zoom buttons to zoom in and out.
Tip: On some devices you can also pinch to zoom in and out.
3. Instruction panel. This panel shows the following information:
The direction of your next turn.
The distance to your next turn.
The name of the next road on your route.
Lane guidance at some junctions.
Note: Select the instruction panel to see a list of turn-by-turn text instructions for your
planned route.
4. Route symbols. Symbols are used on your route to show your starting location, your stops, and
your destination.
5. Main Menu button. Select the button to show the Main Menu.
6. Speed panel. This panel shows the following information:
The speed limit at your location.
Your current speed. If you drive more than 5 km/h or 3 mph over the speed limit the speed
panel turns red. If you drive less than 5 km/h or 3 mph over the speed limit the speed panel
turns orange.
The name of the street you are driving on.
14
7. Current location. This symbol shows your current location. Select the symbol or the speed panel
to open the quick menu.
Note: If your TRUCKER cannot find your location using GPS or other methods, the symbol
appears grey.
8. Route bar. The route bar is shown when you have planned a route.
Important: To see a wider route bar showing additional route information, change the setting
for Route Information.
The route bar
The route bar is shown when you have planned a route. It has an arrival information panel at the
top, and a bar with symbols underneath.
Important: To see a wider route bar showing additional route information, change the setting for
Route Information.
Note: The distance ahead shown by the route bar depends on the overall length of your route.
The arrival information panel shows the following information:
The estimated time that you will arrive at your destination.
The length of time to drive to the destination from your current
location.
A parking button is shown near the destination flag when parking is
available near your destination.
Tip: If your destination is in a different time zone, you see a plus
(+) or a minus (-) sign and the time difference in hours and half
hours in the arrival information panel. The estimated time of arrival
is the local time at your destination.
If you have stops on your route, select this panel to change between
information about the next stop and your final destination.
You can choose the information you see on the arrival information panel.
Traffic status - if your TRUCKER isn't receiving any traffic information, a
symbol showing traffic with a cross appears underneath the arrival
information panel.
The bar uses symbols to show the following information:
The next two stops on your route.
Tip: To quickly remove a stop, select it in the route bar and use the
menu.
Petrol stations that are directly on your route.
TomTom Traffic including heavy rain or snow.
TomTom Speed Cameras and Danger Zones.
Rest stops directly on your route.
You can choose the information you see on your route.
The symbols are in the order that they occur on your route. For traffic
incidents, the symbol for each incident alternates between showing the
type of incident and the delay in minutes. Select a symbol to see more
information about a stop, an incident or a speed camera. If a symbol is
shown on top of another symbol, selecting the symbols zooms in on the
route bar to show each symbol separately. You can then select a symbol.
The total time delay due to traffic jams, weather, and other incidents on
your route, including information provided by IQ Routes, is shown above
15
the symbols.
For a complete list of incident types, see Traffic incidents.
The bottom of the route bar represents your current location and shows
the distance to the next incident on your route. In addition, you can
choose to see the current time if you switch the setting on.
Note: To make the route bar more readable some incidents may not be shown. These incidents
will always be of minor importance and only cause short delays.
The route bar also shows status messages, for example Finding fastest route or Playing route
preview.
Distances and the route bar
The distance ahead shown on the route bar depends on the length of your route, or the distance
remaining on your route.
For remaining distances longer than 50 km (31 miles), only the next 50 km (31 miles) is shown.
The destination icon is not shown.
Tip: You can scroll the route bar to see your whole route.
For remaining distances between 10 km (6 miles) and 50 km (31 miles), the complete distance is
shown. The destination icon is shown fixed at the top of the route bar.
For remaining distances of less than 10 km (6 miles) the complete distance is shown. The
destination icon moves down towards the chevron symbol as you get nearer to your destination.
The top half of the route bar shows twice the distance of the bottom half, as shown in the following
examples:
A remaining distance of 50 km on the route bar is split into 34 km (21 miles) at the top and 16
km (9 miles) at the bottom.
A remaining distance of 10 km on the route bar is split into 6.6 km (4 miles) at the top and 3.3
km (2 miles) at the bottom.
The route bar is constantly updated as you drive.
The quick menu
To open the quick menu, select the current location symbol or the speed panel in the guidance
view.
You can then do any of the following:
Mark a location
Report a new speed camera
Change a speed limit
Avoid a blocked road
See your current location or your latitude/longitude if not on a named road.
Navigation buttons
On the map view or guidance view, select the Main Menu button to open the Main Menu.
The following navigation buttons are available in the Main Menu:
Note: Not all features are supported on all devices.
16
Search
Select this button to search for an address, a place or a Point of Interest,
then plan a route to that location.
Drive Home
Select this button to drive to your home location. If this button is not
included in your main menu, go to My Places to set up your home location.
Drive to Work
Select this button to drive to your work location. If this button is not
included in your main menu, go to My Places to set up your work location.
Recent Destination
Select this button to open the list of your recent destinations. Select a
recent destination to plan a route to that destination.
Current Route
Select this button to clear or change your planned route.
Report Speed
Camera
Select this button to report a speed camera.
My Places
Select this button to show your saved places.
17
My Routes
Select this button to show your saved routes.
Parking
Select this button to find car parks.
Petrol Station
Select this button to find petrol stations.
Voice Control
Select this button to start voice control.
Tip: You can also say the wake-up phrase to start voice control.
TomTom Services
Select this button to see the status of your connection to the internet.
Other buttons
On the map or guidance view, select the Main Menu button to open the Main Menu.
The following buttons are available in the Main Menu screen, in addition to the navigation buttons:
Select this button to open the Settings Menu.
Select this button to open the Help Menu. The Help Menu contains help for
using Voice control if supported by your device, together with other
information about your TRUCKER, for example, map version, device serial
number and legal information.
Select this button to reorder the buttons in the Main Menu.
18
Select this button to return to the previous screen.
Select this button to return to the map view or guidance view.
This symbol shows the status of the Bluetooth connection when you use a
smartphone to connect to TomTom services.
This symbol shows the power level of the battery in your TRUCKER.
This symbol shows that your TRUCKER is connected to TomTom services.
This symbol shows that your TRUCKER is not connected to TomTom
services.
This symbol shows that your TRUCKER is connected to your MyDrive
account.
This symbol shows that your TRUCKER is not connected to your MyDrive
account.
This button shows that you will hear voice instructions. Select the button
to switch off voice instructions. You will no longer hear spoken route
instructions but you will still hear information such as traffic information
and warning sounds.
Tip: You can select the types of instructions you want to hear. Select
Voices in the Settings Menu and select the instructions you want to
hear.
This button shows that you will not hear voice instructions. Select this
button to switch on voice instructions.
This button shows that the display is using day colours. Select the button
to reduce the brightness of the screen and display the map in darker
colours.
When driving at night or when driving through a dark tunnel, it is easier to
view the screen and less distracting for the driver if the brightness of the
screen is dimmed.
Tip: Your device automatically switches between day and night colours
depending on the time of day. To switch off this feature, select
Appearance in the Settings menu and switch off Switch to night colours
when dark.
19
This button shows that the display is using night colours. Select the button
to increase the brightness of the screen and display the map in brighter
colours.
Volume control
On the map or guidance view, select the Main Menu button to open the Main Menu.
Select and slide the volume control to change the volume of voice instructions and warnings. If the
voice instructions are switched off, the volume control will still change the volume of the warnings.
Using gestures
You use gestures to control your TRUCKER.
This Reference Guide explains which gestures to use throughout the guide but here is a complete
list of all the gestures you can use.
Double tap
Touch one finger on the screen twice in rapid succession.
Example of when to use this: Zooming in on the map.
Drag
Put one finger on the screen and move it across the screen.
Example of when to use this: Scrolling around in the map.
Flick
Flick the tip of a single finger across the screen.
Example of when to use this: Scrolling a big distance on the map.
Tip: Flick isn't available on all devices.
Press and hold
Put one finger on the screen for more than 0.5 second.
Example of when to use this: Opening the pop-up menu for a place on the
map.
Pinch to zoom
Touch the screen with your thumb and a finger. Move them apart to zoom
in or move them together to zoom out.
Example of when to use this: Zooming in and out on the map.
Tip: Pinch to zoom isn't available on all devices. If pinch to zoom isn't
available on your TRUCKER, use the zoom buttons to zoom in and out.
20
Tap or select
Tap a single finger on the screen.
Example of when to use this: Selecting an item in the Main Menu.
Tip: To open a pop-up menu for an item on the map, select and hold
the item until the menu opens.
Changing the text and button size
You can change the size of the text and the buttons you see on the screen, for example to make the
text easier to read and the buttons easier to use.
Note: This feature is only available on devices with a 6 inch / 15 cm or larger screen.
To change the size of the text and the buttons, select the Settings button in the Main Menu, then
select Appearance, then select Size of text and buttons. Your device must restart to apply the
change.
Reordering the Main Menu buttons
To reorder the buttons in the Main Menu to suit your preference, do the following:
1. Select the Main Menu button to open the Main Menu.
2. Press and hold the button you want to move for two seconds.
Tip: Alternatively, select the Edit button on the far right of the Main Menu.
The menu button is shown with left and right arrows.
3. Press the left or right arrow on the menu button to move the button to a new position in the
menu.
4. Select and move other buttons to the order you want.
5. Select Done.
21
About TomTom Traffic
TomTom Traffic is a unique TomTom service providing real-time traffic information. For more
information about TomTom services, go to tomtom.com/services.
In combination with IQ Routes, TomTom Traffic helps you plan the optimum route to your
destination taking into account the current local traffic conditions and the weather.
Your TomTom TRUCKER regularly receives information about the changing traffic conditions. If
traffic jams, heavy rain, snow or other incidents are found on your current route, your TRUCKER will
offer to replan your route to try and avoid any delays.
To get TomTom services on your TRUCKER, you must be connected to TomTom services and logged
in to a MyTomTom account.
Note: TomTom services are not available on all devices.
Note: TomTom services are not available in all countries or regions, and not all services are
available in all countries or regions. For more information on available services in each region, go
to tomtom.com/services.
About RDS-TMC
The Traffic Message Channel (TMC), also known as RDS-TMC, transmits traffic information as a radio
signal and is available free of charge in many countries.
TMC is not a TomTom service, but is available when using the TomTom RDS-TMC Traffic Receiver.
Note: The RDS-TMC receiver is not available in all countries.
TomTom is not responsible for the availability or quality of traffic information provided by the
Traffic Message Channel.
The Traffic Message Channel (TMC) is not available in all countries. To check the availability of
TMC services in your country, go to tomtom.com/5826.
The route bar
The route bar is shown when you have planned a route. It has an arrival information panel at the
top, and a bar with symbols underneath.
Important: To see a wider route bar showing additional route information, change the setting for
Route Information.
Note: The distance ahead shown by the route bar depends on the overall length of your route.
Traffic
22
The arrival information panel shows the following information:
The estimated time that you will arrive at your destination.
The length of time to drive to the destination from your current
location.
A parking button is shown near the destination flag when parking is
available near your destination.
Tip: If your destination is in a different time zone, you see a plus
(+) or a minus (-) sign and the time difference in hours and half
hours in the arrival information panel. The estimated time of arrival
is the local time at your destination.
If you have stops on your route, select this panel to change between
information about the next stop and your final destination.
You can choose the information you see on the arrival information panel.
Traffic status - if your TRUCKER isn't receiving any traffic information, a
symbol showing traffic with a cross appears underneath the arrival
information panel.
The bar uses symbols to show the following information:
The next two stops on your route.
Tip: To quickly remove a stop, select it in the route bar and use the
menu.
Petrol stations that are directly on your route.
TomTom Traffic including heavy rain or snow.
TomTom Speed Cameras and Danger Zones.
Rest stops directly on your route.
You can choose the information you see on your route.
The symbols are in the order that they occur on your route. For traffic
incidents, the symbol for each incident alternates between showing the
type of incident and the delay in minutes. Select a symbol to see more
information about a stop, an incident or a speed camera. If a symbol is
shown on top of another symbol, selecting the symbols zooms in on the
route bar to show each symbol separately. You can then select a symbol.
The total time delay due to traffic jams, weather, and other incidents on
your route, including information provided by IQ Routes, is shown above
the symbols.
For a complete list of incident types, see Traffic incidents.
The bottom of the route bar represents your current location and shows
the distance to the next incident on your route. In addition, you can
choose to see the current time if you switch the setting on.
Note: To make the route bar more readable some incidents may not be shown. These incidents
will always be of minor importance and only cause short delays.
The route bar also shows status messages, for example Finding fastest route or Playing route
preview.
Looking at traffic on the map
Traffic incidents are shown on the map. If several traffic incidents overlap the highest priority
incident is shown - for example, a road closure is higher priority than road works or a closed lane.
23
Tip: Select an incident on the map to see more detailed information.
1. Traffic incident that affects your route in your direction of travel.
A symbol or number at the start of the incident shows the type of incident or the delay in
minutes, for example 5 minutes.
The colour of the incident indicates the speed of traffic relative to the maximum allowed speed
at that location, with red being the slowest. The stripes on the traffic jam are also animated to
show the speed of the traffic, where appropriate.
For a complete list of incident types, see Traffic incidents.
Tip: You see weather symbols on the map if there is bad weather such as heavy rain or snow.
2. Traffic incident on your route but in the opposite direction of travel.
3. Traffic incidents on roads that are not visible at your current zoom level.
Looking at traffic on your route
Information about traffic incidents on your route is shown in the route bar on the right-hand side of
the map.
The route bar tells you about traffic delays while you are driving, using symbols to show you where
each traffic incident is located on your route.
Note: If your TRUCKER isn't receiving any traffic information, a symbol showing traffic with a
cross appears underneath the arrival information panel.
Note: To make the route bar more readable some incidents may not be shown. These incidents
will always be of minor importance and only cause short delays.
24
To get more information about an incident, select an incident in the route bar. The map opens
zoomed in on the incident and a pop-up opens showing detailed information about the traffic
incident.
The information shown includes:
The type of traffic incident - general, accident, road works, lane closure or weather such as
heavy rain or snow.
The severity of the incident - slow traffic, queuing traffic or stationary traffic.
The delay time.
The length of the incident.
For a complete list of incident types, see Traffic incidents.
Select the back button to go back to the guidance view.
Traffic incidents
Traffic incidents and warnings are shown in the map view and in the route bar. Symbols shown in a
circle are traffic incidents. Checks are done to see if a faster route is available and your route is
replanned to avoid traffic incidents.
Traffic incident symbols:
Wind
Rain
Fog
Snow
Ice
Stationary traffic
Queuing traffic
Slow traffic
Unknown accident
25
Unknown incident
Roadworks
Lane closure
Road closure
Advanced Lane Guidance
Note: Lane guidance is not available for all junctions or in all countries.
Advanced Lane Guidance helps you prepare for motorway exits and junctions by showing the correct
driving lane for your planned route.
As you approach an exit or junction, the lane you need is shown on the screen and in the instruction
panel.
Tip: To close the lane image, select anywhere on the screen or press the back button.
To turn lane images off, select the Settings button in the Main Menu, then select Appearance.
Switch off the Show previews of motorway exits setting.
Time-dependent speed limits
Some speed limits change depending on the time of day. For example, you may see the speed limit
near schools decrease to 40 km/h or 25 mph in the morning between 08.00 - 09.00 and in the
afternoon between 15.00 - 16.00. Where possible, the speed limit shown in the speed panel changes
to show these variable speed limits.
Some speed limits change depending on driving conditions. For example, the speed limit will
decrease if there is heavy traffic, or the weather conditions are bad. These variable speed limits are
not shown in the speed panel. The speed shown in the speed panel is the maximum speed limit
allowed in good driving conditions.
26
Important: The speed limit shown in the speed panel is only an indication. You must always obey
the actual speed limit for the road you are on and the conditions you are driving in.
27
About My Vehicle
Important: Route planning for a specific vehicle type is available only when a truck map is installed.
If a truck map is not installed, a car route is planned instead.
My Vehicle lets you choose the type of vehicle you are driving so that the route planned by your
device is suitable for your vehicle.
Each vehicle type has adjustable settings for dimensions, weight and maximum speed. Routes
planned by your device avoid restrictions for the vehicle type, and take into account the vehicle's
specific settings. The following list shows you some examples of route restrictions:
A route calculated for a van may be different from the route calculated for a car because of
weight or height restrictions.
A truck may be only permitted to drive on certain roads through a city.
A route planned for a large vehicle, for example Bus, Truck or Other, favours major roads,
assumes you are travelling at a lower average speed and also selects routes without sharp turns.
Important: You must pay attention to all traffic signs, especially those relating to your vehicle’s
dimensions and weight. We cannot guarantee you will never encounter them on your route and
ignoring such restrictions can be dangerous and illegal.
Setting your vehicle type
You can set your vehicle's type and specific settings so that the route planned by your device is
suitable for your vehicle. If you want to use your TRUCKER in another type of vehicle, just change
the vehicle type and settings.
Note: On some navigation devices you are asked to set your vehicle profile when you start your
device for the first time.
1. Select Settings in the Main Menu, then select My Vehicle.
The My Vehicle screen is shown.
2. Select Vehicle Type then select your vehicle type from the list shown.
Setting your vehicle type
28
The My Vehicle screen is shown with the settings for the selected vehicle type.
3. Select each setting and enter the correct value for your vehicle type. If a setting will not be a
route restriction, for example Maximum Speed, you can set it to zero.
Tip: For Bus and Truck vehicle types, the dimensions, weight and maximum speed are pre-set.
Adjust the settings to match your vehicle's actual specifications.
Important: Settings that are set at zero are not used to determine restrictions when a route is
planned.
4. If your vehicle is a Truck transporting hazardous materials, select HAZMAT then select the type
of hazardous material being transported.
5. Return to the map view and plan a route.
A route is planned that avoids route restrictions applicable to your vehicle.
You can find an alternative route or change the route type for all types of vehicles, taking into
account the vehicle's specific settings.
Planning a route for a Bus or Truck
When you plan a route and you have a Bus or Truck as your vehicle type, you are shown the My
Vehicle screen before your route is calculated. Check that your vehicle's settings are correct then
select the continue button:
A route is planned and guidance to your destination begins. As soon as you start driving, the
guidance view is shown automatically.
Viewing route restrictions
If your vehicle type is set to Bus or Truck, you can see route restrictions in the guidance view as you
drive, and in map view when you have planned a route. In map view, zoom in to see the restricted
roads.
Restricted roads are shown coloured. If your planned route uses a restricted road then the
restricted section is shown dotted.
29
Important: You must pay attention to all traffic signs, especially those relating to your vehicle’s
dimensions and weight. We cannot guarantee you will never encounter them on your route and
ignoring such restrictions can be dangerous and illegal.
30
About TomTom MyDrive
TomTom MyDrive is the easy way to share locations and favourites, and save your personal
navigation information. MyDrive synchronises your TomTom TRUCKER with your My Drive account.
You can use MyDrive in a web browser on a computer or as a mobile app on a smartphone or tablet.
Important: To use TomTom MyDrive you need a compatible navigation device.
Use TomTom MyDrive to do the following:
Sync community POI list files from the MyDrive map to your TRUCKER. The POI lists are stored in
My Places and the locations are shown on the map.
Continually save all your locations in My Places to MyDrive. You can see all your My Places
locations on the MyDrive map.
Automatically restore your My Places locations and POIs from MyDrive to your TRUCKER after a
reset.
To activate MyDrive on your TRUCKER, you must be connected to TomTom services.
Logging in to your MyDrive account
You must log in to MyDrive to sync to your MyDrive account. When you log in to your account from
your navigation device, web browser or the MyDrive app, syncing with your MyDrive account
happens automatically.
Logging in to MyDrive on your TRUCKER
1. In the Main Menu, select TomTom Services.
2. Select MyDrive.
3. Enter the email address and password you use for your MyDrive account.
Your TRUCKER connects to your MyDrive account.
4. Return to the map view.
Your TRUCKER automatically saves your personal navigation information to your MyDrive ac-
count.
Logging in to MyDrive using a web browser or the MyDrive app
Log in using your MyDrive account email address and password. When you are logged in, you can see
your personal navigation information from your navigation devices, and you can select destinations
and create Places to sync with your navigation devices.
Showing a planned destination in MyDrive
When you plan a route on your TRUCKER, the destination is synced with your MyDrive account. You
can see the destination when you are logged in to MyDrive in a web browser or when using the
MyDrive app.
Finding and syncing locations using MyDrive
When you are logged in to TomTom MyDrive, you can find locations in MyDrive and sync them with
your TRUCKER My Places locations.
Syncing TomTom MyDrive
31
1. In a web browser or using the MyDrive app, log in to your MyDrive account.
2. On the map, select a destination.
Tip: You can search for a destination or you can move the map and select a destination. You
can also select a destination from your My Places list.
3. Click on the location, then open the pop-up menu and select Add to My Places.
The location is shown in the Favourites list in the MyDrive My Places menu.
4. Log in to MyDrive on your TRUCKER.
Your TRUCKER syncs with your MyDrive account and receives the new Favourites location. The
location is stored in My Places.
Syncing My Places locations with MyDrive
When you are logged in to MyDrive on your TRUCKER, the locations you have added to My Places are
automatically synced with your MyDrive account. You can see your My Places locations and the POI
place lists when you are logged in to MyDrive in a web browser or when using the MyDrive app.
Importing a community POI list
You can find collections of community POIs on the Internet and upload them to My Places using
MyDrive in a web browser. A POI collection might contain, for example, campsites or restaurants for
the area you are travelling in, and provides an easy way to select a location without the need to
search for the location each time.
Your TRUCKER uses .OV2 files for POI collections.
To upload an .OV2 file to your TRUCKER, do the following:
1. In a web browser or using the MyDrive app, log in to your MyDrive account.
2. Select POI Files in the My Places menu.
3. Select Import POI File and browse to your .OV2 file.
Tip: The name of the places list in My Places will be the same as the name of the .OV2 file.
Edit the name of the file so that you can easily recognise it in My Places.
4. Make sure you are logged in to MyDrive on your TRUCKER.
Your TRUCKER syncs with your MyDrive account and receives the new POI file.
Note: Some .OV2 files are large and can take a long time to upload. Make sure that you sync
your TRUCKER before you start driving.
5. Select My Places in the main menu.
Your new POI list is shown in the Places list.
6. Select your new POI list.
Your new POI list opens showing all the POIs in the list. Select the map view to see the POIs on
the map.
Deleting a community POI list
You can only delete an uploaded POI list from your TRUCKER using MyDrive in a web browser.
To delete a POI list, do the following:
1. In a web browser, log in to your MyDrive account.
2. In the My Places menu, select POI Files .
3. Select the POI file you want to delete, then select Delete.
4. Make sure you are logged in to MyDrive on your TRUCKER.
The POI list is removed from your My Places list.
32
Saving and restoring your personal navigation information
When you are logged in to MyDrive on your TRUCKER, your personal navigation information is
continuously and automatically saved to your MyDrive account.
If you reset your TRUCKER, or log in to MyDrive on a different device, your saved personal
navigation information is restored to your TRUCKER or the different device.
The following personal navigation information is saved to your MyDrive account:
MyDrive destinations.
All saved locations in My Places.
All imported POI place lists.
Tip: MyDrive also syncs your locations in My Places with your MyDrive account. You can see your
My Places locations and the POI place lists you have imported in MyDrive on a web browser or on
the MyDrive app.
33
About search
You use search to find a wide range of places and then navigate to them. You can search for the
following:
A specific address, for example, 123 Oxford Street, London.
A partial address, for example, Oxford st Lon.
A type of place, for example, petrol station or restaurant.
A place by name, for example, Starbucks.
A postcode, for example, W1D 1LL for Oxford Street, London.
A city to navigate to a city centre, for example, London.
A POI (Point of Interest) near your current location, for example, restaurant near me.
A mapcode, for example, WH6SL.TR10
Latitude and longitude coordinates, for example,
N 51°30′31″ W 0°08′34″.
Tip: To search for a specific street in the United Kingdom or the Netherlands, type in a postcode,
then leave a space and then type in the house number. For example, "1017CT 35". For other
countries, postcodes are area-based and will give you a list of matching cities, towns and streets
in your search results.
Planning a route to a POI using search
Important: In the interest of safety and to avoid distractions while you are driving, you should
always plan a route before you start driving.
To plan a route to a POI type or a specific POI using search, do the following:
1. Select the Main Menu button to open the Main Menu.
2. Select Search.
The search screen opens with the keyboard showing.
3. Use the keyboard to enter the name of the place you want to plan a route to.
Using Quick Search
34
Tip: If you press and hold a letter key on the keyboard, you get access to extra characters if
they are available. For example, press and hold the letter "e" to access characters 3 e è é ê ë
and more.
You can search for a POI (Point of Interest) type, such as a restaurant or tourist attraction.
Alternatively, you can search for a specific POI, for example "Rosie's Pizzeria".
Note: When searching, the whole map is searched. If you want to change how the search is
done, select the button to the right of the search box. You can then change where the search
is done, for example along the route or in a city.
4. As you type, suggestions based on what you have entered are shown in columns. You can
continue typing or select a suggestion.
Tip: To see more results, hide the keyboard or swipe the results list to scroll it.
Tip: You can switch between seeing the results on the map or in a list by selecting the
list/map button:
5. Select a POI type or an individual POI. If you selected a POI type, select a POI.
The location is shown on the map.
35
6. To see more information about the POI, select the POI on the map and then select the pop-up
menu button. Select More Information on the pop-up menu.
You see more information about the POI such as the phone number, full address and email.
7. To plan a route to this destination, select Drive or Ride depending on which device you are
using.
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: If your destination is in a different time zone, you see a plus (+) or a minus (-) sign and
the time difference in hours and half hours in the arrival information panel. The estimated
time of arrival is the local time at your destination.
Tip: You can add a stop to a route that you have already planned.
Tip: You can save a route using My Routes.
Planning a route to a POI using online search
Important: In the interest of safety and to avoid distractions while you are driving, you should
always plan a route before you start driving.
Note: Searching online is only available on connected devices. To search online on your TRUCKER,
you must be connected to TomTom services.
If you did a POI search but could not find the POI you were looking for, you can search TomTom
Places online. To find POIs by searching online, do the following:
1. Search for a POI using Search in the Main Menu.
The search results are shown in two columns.
36
2. Select Search Places Online.
3. Use the keyboard to enter the name of the POI you want to find, then press the Search button
on the keyboard.
Tip: If you press and hold a letter key on the keyboard, you get access to extra characters if
they are available. For example, press and hold the letter "e" to access characters 3 e è é ê ë
and more.
You can search for a POI (Point of Interest) type, such as a restaurant or tourist attraction.
Alternatively, you can search for a specific POI, for example "Rosie's Pizzeria".
Note: When searching, you can search near your current location, in a town or city, or near
your destination. If you want to change how the search is done, select the button to the right
of the search box.
The search results are shown in a column.
Tip: To see more results, hide the keyboard or swipe the results list to scroll it.
Tip: You can switch between seeing the results on the map or in a list by selecting the
list/map button:
4. Select an individual POI from the list.
The location is shown on the map.
5. To see more information about the POI, select the POI on the map and then select the pop-up
menu button. Select More Information on the pop-up menu.
You see more information about the POI such as the phone number, full address and email.
37
6. To plan a route to this destination, select Drive or Ride depending on which device you are
using.
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: If your destination is in a different time zone, you see a plus (+) or a minus (-) sign and
the time difference in hours and half hours in the arrival information panel. The estimated
time of arrival is the local time at your destination.
Tip: You can add a add a stop to a route that you have already planned.
Tip: You can save a route using My Routes.
Entering search terms
Select Search in the Main menu to start searching for addresses and POIs. The search screen opens
showing the keyboard and the following buttons:
1. Back button.
Select this button to go back to the previous screen.
2. Search input box.
Enter your search term here. As you type, matching addresses and POIs are shown.
Tip: If you press and hold a letter key on the keyboard, you get access to extra characters if
they are available. For example, press and hold the letter "e" to access characters 3 e è é ê ë
and more.
Tip: To edit, select a word you have already typed to place the cursor. You can then insert or
delete characters.
3. Type of search.
By default, the whole of the current map is searched. Once you have used search, the last
search type you selected is used. Select this button to change the type of search to any of the
following:
Whole map
Select this option to search the whole of your current map with no
limit to the search radius. Your current location is the centre of the
search. The results are ranked by exact match.
38
Near me
Select this option to search with your current GPS location as the
search centre. The results are ranked by distance.
In town or city
Select this option to use a town or city as the centre for your search.
You need to enter the town or city name using the keyboard. When
you have selected the town or city from the results list, you can
search for an address or POI in that city.
Along route
When a route has been planned, you can select this option to search
along your route for a specific type of location, for example, petrol
stations. When prompted, enter the type of location and then select it
in the right-hand column to carry out the search.
Near destination
When a route has been planned, you can select this option to use your
destination as the centre for your search.
Latitude Longitude
Select this option to enter a pair of latitude longitude coordinates.
4. View button.
Select this button to return to the map view or guidance view.
5. 123?! button.
Select this button to use numbers and symbols on your keyboard. Select the =\< button to
toggle between the numbers and more symbols. Select the ABC button to go back to the general
keyboard.
6. Keyboard layout button.
Select this button to change your keyboard layout to another language. You can choose up to
four layouts from the list. If you have more than one layout selected, selecting the keyboard
layout button opens a pop-up so you can quickly swap between your selected keyboard layouts.
Press and hold this button to go directly to the list of all the layouts.
7. List/map button.
Select this button to switch between showing the results in a list or showing the results on the
map.
8. Show/hide keyboard.
Select this button to show or hide the keyboard.
Tip: Select the Shift key once to make the next letter you type upper case. Double tap the Shift
key to use Caps-Lock where all the letters you type are upper case. Select the Shift key once to
quit Caps-Lock.
Tip: To cancel a search, select the map/guidance view button in the top right-hand corner of the
screen.
Working with search results
Your search results are shown in two columns.
Address and city matches are shown in the left-hand column, and POIs, types of POIs and Places are
shown in the right-hand column.
Tip: To see more results, hide the keyboard or swipe the results list to scroll it.
39
Tip: You can switch between seeing the results on the map or in a list by selecting the
list/map button:
When you select an address from the list of search results, you can choose to show it on the map,
add a crossroad or plan a route to that chosen location. To get an exact address you can add the
house number.
If you show the result on the map, you can use the pop-up menu to adding a location from My Places
or search near this location. If a route is already planned, you can add the location to your current
route.
40
Note: The best search results are shown on the map. When you zoom in, the lower ranked search
results are gradually shown.
About postcodes
When searching using a postcode, your results depend on the type of postcode used in the country
that you are searching in.
The following types of postcodes are used:
Postcodes that navigate you to a street or part of a street.
Postcodes that navigate you to an area comprising, for example, a single town, several villages
in a rural area or a district in a large city.
Postcodes for streets
Countries such as the Netherlands and the United Kingdom use this type of postcode. When you
search using this type of postcode, enter the postcode, then leave a space and then optionally enter
the house number. For example, "1017CT 35". Your device then plans a route to a specific house or
building on a specific street.
Postcodes for areas
Countries such as Germany, France and Belgium use this type of postcode. If you search using a
postcode for an area, your results include all the streets in a city district, the whole town, or the
villages within that postcode.
You may get results from multiple countries if you enter a postcode for an area.
Note: If you search using a postcode for an area, you will not get a specific address in your
results.
This type of postcode is still very useful in reducing the number of search results. For example, a
search for Neustadt in Germany returns a long list of possible results. Adding a space followed by
the postcode for an area narrows the results down to the Neustadt that you are looking for.
As another example, if you want to search in a city, enter a postcode for an area and select the city
centre you are searching for from the results.
About mapcodes
In countries where roads and houses have no names or addresses, you can use a mapcode instead. A
mapcode represents a location.
Every location on Earth, including those in the sea like islands and oil rigs, can be represented by a
mapcode. Mapcodes are short, and easy to recognise, remember and communicate. They are
precise to a few metres, which is good enough for every-day use.
Go to mapcode.com for instructions on how to find the mapcode for a location.
Mapcodes are more precise and more flexible than the address on a business card. You can choose a
location that you want to associate with your address, for example, the main entrance or the
entrance to a car park.
List of POI type icons
Legal and financial services
41
Court house
Cash dispenser
Legal - Solicitors
Financial institution
Legal - other services
Food services
Convenience store
Fast food restaurant
Restaurant
Chinese restaurant
Accommodation
Hotel or motel
Luxury hotel
Camping ground
Economy chain hotel
Emergency services
Hospital or polyclinic
Dentist
Police station
Veterinarian
Doctor
Fire station
Car-related services
Outside parking
Petrol station
Parking garage
Car wash
Car dealer
Vehicle inspection centre
42
Rental car facility
Electrical car charging
point(s)
Rental car parking
Car repair facility
Other services
Embassy
Pet services
Government office
Telecommunication
Company
Community service
Post office
Pharmacy
Shopping centre
Beauty services
Tourist information office
Shop
Education
College or university
School
Library
Convention centre
Leisure
Casino
Winery
Theatre
Tourist attraction
Cinema
Zoo
43
Concert hall
Amusement park
Museum
Exhibition centre
Opera
Cultural centre
Nightlife
Leisure centre
Sport
Playing field
Swimming pool
Mountain peak
Water sports
Beach
Tennis court
Park or recreation area
Ice skating rink
Yacht basin or marina
Sports centre
Stadium
Golf course
Religion
Church
Place of worship
Travel
Railway station
Mountain pass
Airport
Scenic or panoramic view
44
Ferry terminal
Postcode
Note: Not used in all
countries.
Border crossing
Residential area
Bus station
Petrol station
Toll gate
Electrical car charging
stations
Rest area
Truck stop
City centre
45
Planning a route to an address using search
Important: In the interest of safety and to avoid distractions while you are driving, you should
always plan a route before you start driving.
To plan a route to an address using search, do the following:
1. Select the Main Menu button to open the Main Menu.
2. Select Search.
The search screen opens with the keyboard showing.
3. Use the keyboard to enter the name of the place you want to plan a route to.
Tip: If you press and hold a letter key on the keyboard, you get access to extra characters if
they are available. For example, press and hold the letter "e" to access characters 3 e è é ê ë
and more.
You can search for an address, town, city, postcode or mapcode.
Tip: To search for a specific street in the United Kingdom or the Netherlands, type in a post-
code, then leave a space and then type in the house number. For example, "1017CT 35". For
other countries, postcodes are area-based and will give you a list of matching cities, towns and
streets in your search results.
Note: When searching, the whole map is searched. If you want to change how the search is
done, select the button to the right of the search box. You can then change where the search
is done, for example, to being along the route or in a city.
Planning a route
46
4. As you type the address, suggestions based on what you have entered are shown in columns. You
can continue typing or select a suggestion.
Tip: To see more results, hide the keyboard or swipe the results list to scroll it.
Tip: You can switch between seeing the results on the map or in a list by selecting the
list/map button:
5. Select an address suggestion.
6. Enter the house number if you have one and haven't entered it already.
Tip: If you enter a house number that is not found, then the number appears red. The nearest
house number that is found is shown in the Drive button. You can enter a new house number,
or you can select Drive to drive to the nearest house number.
7. Select Drive or Ride depending on which device you are using.
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: If your destination is in a different time zone, you see a plus (+) or a minus (-) sign and
the time difference in hours and half hours in the arrival information panel. The estimated
time of arrival is the local time at your destination.
Tip: You can add a stop to a route that you have already planned.
Tip: You can save a route using My Routes.
47
Planning a route to a city centre
Important: In the interest of safety and to avoid distractions while you are driving, you should
always plan a route before you start driving.
To plan a route to a city centre using search, do the following:
1. Select the Main Menu button to open the Main Menu.
2. Select Search.
The search screen opens with the keyboard showing.
3. Use the keyboard to enter the name of the city or town you want to plan a route to.
You can search for a town, city, or postcode.
Tip: To search for a specific city you can use the city's postcode or the country. For example,
searching for Essen will return many results. If you search for Essen 2910 or Essen Belgium then
that city will be at the top of the results. You can then search in the city.
Tip: When searching, the whole map is searched. If you want to change how the search is
done, select the button to the right of the search box. You can then change where the search
is done, for example, to being along the route or in a city.
4. As you type the address, suggestions based on what you have entered are shown in columns. You
can continue typing or select a suggestion.
Tip: To see more results, hide the keyboard or swipe the results list to scroll it.
Tip: You can switch between seeing the results on the map or in a list by selecting the
list/map button:
5. Select the city in the left-hand column.
48
The city name is shown in the right side of the search input box, and the city centre POI is
shown below in the right-hand column.
6. Select the city centre POI.
The city centre location is shown on the map.
7. Select Drive or Ride depending on which device you are using.
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: If your destination is in a different time zone, you see a plus (+) or a minus (-) sign and
the time difference in hours and half hours in the arrival information panel. The estimated
time of arrival is the local time at your destination.
Tip: You can add a stop to a route that you have already planned.
Tip: You can save a route using My Routes.
Planning a route to a POI using search
Important: In the interest of safety and to avoid distractions while you are driving, you should
always plan a route before you start driving.
To plan a route to a POI type or a specific POI using search, do the following:
1. Select the Main Menu button to open the Main Menu.
49
2. Select Search.
The search screen opens with the keyboard showing.
3. Use the keyboard to enter the name of the place you want to plan a route to.
Tip: If you press and hold a letter key on the keyboard, you get access to extra characters if
they are available. For example, press and hold the letter "e" to access characters 3 e è é ê ë
and more.
You can search for a POI (Point of Interest) type, such as a restaurant or tourist attraction.
Alternatively, you can search for a specific POI, for example "Rosie's Pizzeria".
Note: When searching, the whole map is searched. If you want to change how the search is
done, select the button to the right of the search box. You can then change where the search
is done, for example along the route or in a city.
4. As you type, suggestions based on what you have entered are shown in columns. You can
continue typing or select a suggestion.
Tip: To see more results, hide the keyboard or swipe the results list to scroll it.
50
Tip: You can switch between seeing the results on the map or in a list by selecting the
list/map button:
5. Select a POI type or an individual POI. If you selected a POI type, select a POI.
The location is shown on the map.
6. To see more information about the POI, select the POI on the map and then select the pop-up
menu button. Select More Information on the pop-up menu.
You see more information about the POI such as the phone number, full address and email.
7. To plan a route to this destination, select Drive or Ride depending on which device you are
using.
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: If your destination is in a different time zone, you see a plus (+) or a minus (-) sign and
the time difference in hours and half hours in the arrival information panel. The estimated
time of arrival is the local time at your destination.
Tip: You can add a stop to a route that you have already planned.
Tip: You can save a route using My Routes.
Planning a route to a POI using online search
Important: In the interest of safety and to avoid distractions while you are driving, you should
always plan a route before you start driving.
Note: Searching online is only available on connected devices. To search online on your TRUCKER,
you must be connected to TomTom services.
If you did a POI search but could not find the POI you were looking for, you can search TomTom
Places online. To find POIs by searching online, do the following:
1. Search for a POI using Search in the Main Menu.
51
The search results are shown in two columns.
2. Select Search Places Online.
3. Use the keyboard to enter the name of the POI you want to find, then press the Search button
on the keyboard.
Tip: If you press and hold a letter key on the keyboard, you get access to extra characters if
they are available. For example, press and hold the letter "e" to access characters 3 e è é ê ë
and more.
You can search for a POI (Point of Interest) type, such as a restaurant or tourist attraction.
Alternatively, you can search for a specific POI, for example "Rosie's Pizzeria".
Note: When searching, you can search near your current location, in a town or city, or near
your destination. If you want to change how the search is done, select the button to the right
of the search box.
The search results are shown in a column.
Tip: To see more results, hide the keyboard or swipe the results list to scroll it.
Tip: You can switch between seeing the results on the map or in a list by selecting the
list/map button:
4. Select an individual POI from the list.
The location is shown on the map.
52
5. To see more information about the POI, select the POI on the map and then select the pop-up
menu button. Select More Information on the pop-up menu.
You see more information about the POI such as the phone number, full address and email.
6. To plan a route to this destination, select Drive or Ride depending on which device you are
using.
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: If your destination is in a different time zone, you see a plus (+) or a minus (-) sign and
the time difference in hours and half hours in the arrival information panel. The estimated
time of arrival is the local time at your destination.
Tip: You can add a add a stop to a route that you have already planned.
Tip: You can save a route using My Routes.
Planning a route using the map
Important: In the interest of safety and to avoid distractions while you are driving, you should
always plan a route before you start driving.
To plan a route using the map, do the following:
1. Move the map and zoom in until you can see the destination that you want to navigate to.
Tip: You can also select a map symbol to open the pop-up menu, then select the drive button
to plan a route to that location.
2. When you have found your destination on the map, select it by pressing and holding the screen
for about one second.
53
A pop-up menu shows the nearest address.
3. To plan a route to this destination, select the drive button:
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: You can use the location you selected in other ways, such as adding it to My Places, by
selecting the pop-up menu button.
Tip: If your destination is in a different time zone, you see a plus (+) or a minus (-) sign and
the time difference in hours and half hours in the arrival information panel. The estimated
time of arrival is the local time at your destination.
Tip: You can add a stop to a route that you have already planned.
Tip: You can save a route using My Routes.
Planning a route using My Places
To navigate to one of My Places from your current location, do the following:
1. Select the Main Menu button to open the Main Menu.
54
2. Select My Places.
A list of all your Places opens.
3. Select the Place you want to navigate to, for example Home.
Your chosen Place is shown on the map with a pop-up menu.
4. To plan a route to this Place, select the drive button:
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: If your destination is in a different time zone, you see a plus (+) or a minus (-) sign and
the time difference in hours and half hours in the arrival information panel. The estimated
time of arrival is the local time at your destination.
Tip: You can add a stop to a route that you have already planned.
Tip: You can save a route using My Routes.
55
Planning a route using coordinates
Important: In the interest of safety and to avoid distractions while you are driving, you should
always plan a route before you start driving.
To plan a route using a pair of coordinates, do the following:
1. Select the Main Menu button to open the Main Menu.
2. Select Search.
The search screen opens with the keyboard showing.
3. Select the type of search button to the right of the search box.
4. Select Latitude Longitude.
5. Type in your pair of coordinates. You can enter any of these coordinate types:
Decimal values, for example:
N 51.51000 W 0.13454
51.51000 -0.13454
Tip: For decimal values you don't have to use a letter to indicate the latitude and longi-
tude. For locations west of the 0 meridian and locations south of the equator, use a minus
sign (-) before the coordinate.
Degrees, minutes and seconds, for example:
N 51°30′31″ W 0°08′34″
GPS standard coordinates, for example:
N 51 30.525 W 0 08.569
Note: The bar below the coordinates goes red if you enter coordinates that are not recognised
by your TRUCKER.
6. As you type in the coordinates, suggestions are shown based on what you have entered. You can
continue typing or select a suggestion.
Towns and roads are shown on the left, POIs are shown on the right.
Tip: To see more results, hide the keyboard or swipe the results list to scroll it.
Tip: You can switch between seeing the results on the map or in a list by selecting the
list/map button:
7. Select a suggestion for your destination.
The location is shown on the map.
8. To plan a route to this destination, select Drive or Ride depending on which device you are
using.
56
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: If your destination is in a different time zone, you see a plus (+) or a minus (-) sign and
the time difference in hours and half hours in the arrival information panel. The estimated
time of arrival is the local time at your destination.
Tip: You can add a stop to a route that you have already planned.
Tip: You can save a route using My Routes.
Planning a route using a mapcode
Important: In the interest of safety and to avoid distractions while you are driving, you should
always plan a route before you start driving.
To plan a route using a mapcode, do the following:
1. Select the Main Menu button to open the Main Menu.
2. Select Search.
The search screen opens with the keyboard showing.
3. Type in your mapcode. You can enter any of these mapcode types:
International, for example, WH6SL.TR10.
Country-specific, for example, GBR 8MH.51.
Alternative country-specific, for example, GBR 28.Y6VH or GBR LDGZ.VXR.
Tip: All the mapcodes in this example are for the same location - Edinburgh Castle in the UK.
See About mapcodes for information on how to get a mapcode for a location.
4. As you type in the mapcode, suggestions are shown based on what you have entered. You can
continue typing or select a suggestion.
Towns and roads are shown on the left, POIs are shown on the right.
Tip: To see more results, hide the keyboard or swipe the results list to scroll it.
Tip: You can switch between seeing the results on the map or in a list by selecting the
list/map button:
5. Select a suggestion for your destination.
6. Select Drive.
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: If your destination is in a different time zone, you see a plus (+) or a minus (-) sign and
the time difference in hours and half hours in the arrival information panel. The estimated
time of arrival is the local time at your destination.
Tip: You can add a stop to a route that you have already planned.
57
Tip: You can save a route using My Routes.
Finding an alternative route
Important: In the interest of safety and to avoid distractions while you are driving, you should
always plan a route before you start driving.
To find an alternative route, do the following:
1. Plan a route as usual.
2. On the map view, select the route itself.
3. Select the pop-up menu button to open the menu.
4. Select Alternative Route and then select Find alternative.
Up to three alternative routes are shown on the map view. Each alternative route shows the
difference in travel time in a balloon.
Tip: Information from the Lifetime Traffic service is used when calculating alternative routes.
Any route that is 50% longer in time than the original route is not shown.
5. Select your chosen route by tapping on the time balloon.
6. Select Let's go.
7. Guidance to your destination begins. As soon as you start driving, the guidance view is shown
automatically.
Note: You can also find alternative routes by selecting Current Route in the main menu,
followed by Find Alternative.
Planning a route in advance
You can plan a route in advance before you drive it. You can save the route as part of your My
Routes list.
To plan a route in advance, do the following:
1. Select the Main Menu button to open the Main Menu.
58
2. Select Search.
The search screen opens with the keyboard showing.
3. Use the keyboard to enter the name of the location you want to use as a starting point.
4. Select an address or POI suggestion.
5. Select Show on Map.
6. Select the pop-up menu button.
A pop-up menu shows a list of options.
7. Select Use as Starting Point.
Repeat the search steps to choose your destination, and then select Drive or Ride in the pop-up
menu.
Your route is planned using your chosen starting point and destination. The estimated time of
arrival is shown at the top of the route bar.
Tip: If you don't want to use search to choose your starting point and destination, go to the
map view and press and hold to select a location.
Tip: Stops, POIs, Places and the destination can all be selected as starting points using their
pop-up menus.
Changing the starting point to be your current location
1. Select the starting point of the route in the map view.
2. Select the pop-up menu button.
59
A pop-up menu shows a list of options.
3. Select Remove Starting Point.
Your route is replanned with your current location as the starting point.
Changing the starting point into a stop
1. Select the starting point on the route in the map view.
2. Select the pop-up menu button.
A pop-up menu shows a list of options.
3. Select Change to a Stop.
Your route is replanned with the starting point changed into a stop.
Finding a car park
To find a car park, do the following:
1. Select the Main Menu button to open the Main Menu.
2. Select Parking.
60
The map opens showing the locations of car parks.
If a route is planned, the map shows car parks near your destination. If a route isn't planned,
the map shows car parks near your current location.
You can change the screen to show a list of car parks by pressing this button:
You can select a car park from the list to locate it on the map.
Tip: You can scroll down the list of results using the scroll bar on the right side of the screen.
If you want to change how the search is done, select the button to the right of the search box.
You can then change where the search is carried out, for example, to search near you or the
whole map.
61
3. Select a car park from the map or the list.
A pop-up menu opens on the map showing the name of the car park.
4. To plan a route to your chosen car park, select the drive button:
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: You can add a car park as a stop on your route by using the pop-up menu.
Finding a petrol station
To find a petrol station, do the following:
1. Select the Main Menu button to open the Main Menu.
2. Select Petrol Station.
The map opens showing the locations of petrol stations.
62
If a route is planned, the map shows petrol stations along your route. If a route isn't planned,
the map shows petrol stations near your current location.
You can change the screen to show a list of petrol stations by pressing this button:
You can select a petrol station from the list to locate it on the map.
Tip: You can scroll down the list of results using the scroll bar on the right side of the screen.
If you want to change how the search is done, select the button to the right of the search box.
You can then change where the search is carried out, for example, to search near you or the
whole map.
3. Select a petrol station from the map or the list.
A pop-up menu opens on the map showing the name of the petrol station.
63
4. To plan a route to your chosen petrol station, select the drive button:
A route is planned and then guidance to your destination begins. As soon as you start driving,
the guidance view is shown automatically.
Tip: You can add a petrol station as a stop on your route by using the pop-up menu. A petrol
station that is a stop on your route has a blue icon.
64
The Current Route Menu
When you have planned a route or track, select the Current Route button in the Main Menu to open
the Current Route Menu.
The following buttons are available in the menu:
Clear Route or
Track
Select this button to clear the currently planned route or track.
The Current Route Menu closes and you return to the map view.
Find Alternative
You see this button when you have planned a route. Select this button to
show up to three alternative routes on the map view.
Avoid Blocked Road
Select this button to avoid an unexpected obstacle that is blocking the
road on your route.
Avoid Toll Roads
and More
Select this button to avoid some types of route features that are on your
currently planned route. These include ferries, toll roads and unpaved
roads.
Show Instructions
Select this button to see a list of turn-by-turn text instructions for your
planned route.
The instructions include the following:
The street name.
Up to two road numbers shown in road shields whenever available.
An instruction arrow.
An instruction description.
The distance between two consecutive instructions.
Exit number.
Tip: You can also select the instruction panel in the guidance view to
see turn-by-turn text instructions.
Changing your route
65
Add Stop to Route
Select this button to add a stop to your currently planned route. You can
also add a stop to your route directly from the map.
Add to My Routes
If you plan a new route that has not already been saved, you see this
button. Select this button to save this route as part of your My Routes list.
Save Changes to
Route
If you make a change to a My Route, you see this button. Select this
button to save the changes.
Change Route Type
Select this button to change the type of route used to plan your route.
Your route will be recalculated using the new route type.
Reorder Stops
Select this button to see the lists of stops for your current route. You can
then change the order of the stops on your route.
For a route without stops, you can also select this button to reverse your
route.
Drive to Route or
Track
Select this button to plan a route from your current location to the
starting point of a My Route. The starting point is converted to a stop.
Play Route or
Track Preview
Select this button to watch a preview of your planned route or track.
Stop Route Preview
Select this button to stop the preview of your planned route.
Avoiding a blocked road
If there is a blocked road on your route you can change your route to avoid it.
1. In the guidance view, select the current location symbol or the speed panel.
Tip: The speed panel is only shown when you have started driving on your route.
66
2. Select Avoid Blocked Road.
A new route is found that avoids the blocked road. You may get shown up to two alternatives
depending on the road network between you and your destination.
The new route is shown on the map view with the difference in travel time in a balloon.
Note: It may not be possible to find an alternative route around the blocked road if none
exists.
3. Select the new route by selecting the time balloon.
4. Select Let's go.
Guidance to your destination resumes avoiding the blocked road. As soon as you start driving,
the guidance view is shown automatically.
Types of route
Select Change Route Type to change the type of route planned to your current destination. Your
route is recalculated using the new route type.
You can select the following types of route:
Important: If you have Bus or Truck as your vehicle type, you can only choose route types Fastest
route or Shortest route.
Fastest route - the fastest route to your destination. Your route is constantly checked taking
into account the traffic conditions.
Shortest route - the shortest route to your destination. This may take much longer than the
fastest route.
Most eco-friendly route - the most fuel-efficient route.
Avoid Motorways - this type of route avoids all motorways.
Walking Route - this type of route is optimised for walking.
Bicycle Route - this type of route is optimised for bicycles.
You can set the default route type in the Settings Menu.
Route features
You can choose to avoid some features that are on your currently planned route. You can avoid the
following route features:
Toll Roads
Ferries and car shuttle trains
Carpool Lanes
Unpaved Roads
Note: Carpool lanes are sometimes known as High Occupancy Vehicle Lanes (HOV lanes) and are
not present in every country. To travel on these lanes, you may need to have more than one
person in the car, for example, or the car may need to use environmentally-friendly fuel.
If you choose to avoid a route feature, a new route is planned.
In Route Planning in the Settings Menu, you can set how each route feature is handled when a new
route is planned.
Adding a stop to your route from the current route menu
1. In the Main Menu, select Current Route.
2. Select Add Stop to Route.
The map view is shown.
3. To select a stop, do one of the following steps:
67
Zoom in on the map, then press and hold to select a location. In the pop-up menu, select
Add to Current Route.
Select Search and search for a location. When you have found a location, select the Add
Stop to Route button.
Your route is recalculated to include your stop.
Adding a stop to your route using the map
1. Press the switch view button to show the map.
Your complete route is shown on the map.
2. Zoom in on the map, then press and hold to select a location.
3. Select the pop-up menu button.
4. Select Use in Route.
5. Select Add to Current Route.
Your route is recalculated to include your stop.
Deleting a stop from your route
1. Press the switch view button to show the map.
Your complete route is shown on the map.
2. In the route bar, press the stop you want to delete.
The map zooms in to the stop and shows a pop-up menu.
Tip: If you select the wrong stop press the back button to return to the map.
3. Select Delete This Stop.
The stop is deleted and your route is recalculated.
Tip: You can also delete a stop by selecting Current Route in the Main Menu, followed by List
Edit.
Reordering stops on a route
1. In the Main Menu, select Current Route.
2. Select Reorder Stops.
The map view is shown with the route cleared. The starting point, destination and all the stops
are shown.
3. Select the stops one by one in the order you wish to drive them.
The symbols change to a flag as you select each stop. The last stop you select becomes your
destination.
Your route is recalculated with the stops in the changed order.
68
About My Routes
My Routes provides an easy way to create saved routes with optional stops, sometimes known as an
itinerary. You can use My Routes to save, retrieve and edit routes.
You may want to use My Routes in one or more of the following situations:
While working - Your job involves driving several routes with multiple stops on a daily basis.
Your routes can change and you need to be flexible and be able to change the order of your
stops or change the planned route.
While on holiday - You are going on holiday and want to plan and save a route. Your route
includes scenic roads, stops at various hotels, and other places like tourist attractions.
While commuting to work - You want to add one or two regular stops between home and work.
Your route back home in the evening is the reverse of your route to work in the morning.
You can add the route that you have planned on the map to your My Routes list by selecting it.
Saving a route
1. Plan a route using the steps described in Planning a route.
Tip: If you cannot see your planned route on the map view, select the back button to show
your route.
2. Select the route.
3. Select the pop-up menu button to open the menu.
4. Select Manage Route.
5. Select Add to My Routes.
The name of the route is shown in the edit screen.
6. Edit the name of the route so that you can easily recognise it.
7. Select Add to save your route in the My Routes list.
Tip: You can also save a route using the Add to My Routes button in the Current Route menu.
My Routes
69
Navigating using a saved route
To navigate using a previously saved route, do the following:
1. In the Main Menu, select My Routes.
2. Select a route from your list.
The route is shown on the map view.
3. To navigate to the start of the saved route, select Drive.
The starting point of the saved route is converted to your first stop and then the route is
planned. Guidance to your destination begins from your current location. As soon as you start
driving, the guidance view is shown automatically.
Tip: There are two other ways to navigate using a saved route:
Select the starting point of the route. When the pop-up menu opens, select Change to a Stop.
Alternatively, select Drive to Route in the Current Route menu.
Adding a stop to a saved route using the map
Note: You can also press and hold a location on the map and select Add to Current Route from
the pop-up menu.
1. Press the switch view button to show the map.
Your complete route is shown on the map.
2. Select the route.
70
3. Select the pop-menu button to open the menu.
4. Select Manage Stops.
5. Select Add Stop to Route.
6. Select your new stop on the map.
Tip: If you know the name of your new stop, you can use Search to select your stop instead of
using the map.
7. Select the Add Stop button to add this location as a stop.
Your route is recalculated to include your stop.
Tip: To update the saved route in your My Routes list with the changes, select the route om
the map then select Save Changes to Route in the pop-up menu.
Deleting a route from My Routes
1. In the Main Menu, select My Routes.
2. Select Edit List.
3. Select the routes you want to delete.
4. Select Delete.
71
About voice control
Note: Voice control is not supported on all devices or in all languages.
Instead of selecting items on the screen to control your TomTom TRUCKER, you can use your voice
to control your TRUCKER.
You can use voice control to control many of the navigation features on your TRUCKER, or to change
settings. For example, you can change the screen to day colours, avoid a blocked road or decrease
the volume just by using your voice.
Voice control is active in the map view, the guidance view, and the voice control screen.
Important: Voice control requires a voice that speaks street names. When there is no voice that
speaks street names installed and selected on your TomTom TRUCKER, this feature is not available.
To select a voice that reads aloud street names, select Voices in the Settings menu, then select
Choose a voice and select a Computer voice that reads aloud street names.
Starting voice control
In map view or guidance view, say the wake-up phrase to start voice control. The default wake-up
phrase is "Hello TomTom", but you can make your own wake-up phrase.
Tip: Voice control is off by default. You can switch the wake-up phrase on or off in the settings
menu.
Alternatively, you can select Voice Control in the Main Menu:
When voice control is ready to use, you see the voice control screen and your TRUCKER says "I'm
listening". Speak when you hear the beep.
Note: If the volume control is set to 20% or lower, the volume automatically changes to 50% when
you start voice control.
Making your own wake-up phrase
You can make your own wake-up phrase to start Voice Control. You can choose any words you like
to make your wake-up phrase fun or easy to say.
To make your own wake-up phrase, do the following:
1. Select Voice Control in the Settings menu.
2. Select Change the wake-up phrase.
3. Enter your wake-up phrase using the keyboard.
Your phrase should have at least three syllables. Don't use a phrase that you often say or hear.
The indicator shows how good your phrase is:
Red means your phrase won't work.
Voice control (Speak&Go)
72
Orange means your phrase might work.
Green means your phrase is good.
4. Select Hear it to listen to your wake-up phrase.
5. Select Done then Yes to save your wake-up phrase.
Your new wake-up phrase is ready to use. Start Voice Control and try it.
The voice control screen
1. Examples of what you can say.
Tip: Say "All commands" to see a list of commands you can say. Alternatively, select Help in
the Main menu, then select Voice control and then select Which commands can I say?.
2. The status of voice control on your TRUCKER. You can speak when your TRUCKER says "I'm
listening" and you see the microphone symbol in the left corner.
The status message tells you if voice control cannot understand what you said, and gives you
instructions about using voice control. At the same time, voice control reads aloud the message.
3. The microphone symbol shows you when you can speak:
This symbol shows you that voice control is ready to listen. Speak when you hear the
beep.
This symbol shows you that voice control is busy.
4. The microphone monitor. While you are speaking the microphone monitor shows how well voice
control can hear your voice:
A light blue bar means voice control can hear your voice.
A red bar means your voice is too loud for voice control to recognise individual words.
A dark blue bar means your voice is too quiet for voice control to recognise individual words.
73
Some tips for using voice control
You can help your TRUCKER understand what you are saying by following these tips:
Mount your TRUCKER about an arm's length in front of you, away from speakers or air vents.
Reduce background noise such as voices or the radio. If there is excessive road noise, you may
need to speak in the direction of the microphone.
Speak fluently and naturally as though speaking to a friend.
When saying an address, try not to pause between parts of the address or add extra words.
Say "number one" or "number two" and not "one " or "two" when selecting an item from a list
such as a house number.
Try not to correct mistakes, for example "Number four, oh I mean number five".
Important: Voice control on your TRUCKER is specifically for native speakers of the selected
language who have a neutral accent. If you have a strong local or foreign accent, voice control may
not understand everything that you say.
What you can use voice control for
To view the complete list of available commands, select Help in the Main menu, then Voice control
and then Which commands can I say?.
When voice control is on, you can also say "All commands" to view the list of available commands.
Here are some of the commands you can say when voice control is active:
Global commands
"Help", "Back", and "Cancel"
Navigation and route
"Go home" and "Travel via home"
"Go to a car park" and "Go to a petrol station"
"Go via a car park" and "Go via a petrol station"
"Display My Places" and "Recent destinations"
"Travel via a recent destination", and "Travel via a saved place"
"Report speed camera"
"When will I get there?"
"Mark the current location"
"Add current location to My Places"
"Clear route"
"What's the next instruction?"
Device settings
"Volume 70%", "Volume up", and "Volume down"
"Mute", and "Sound on"
"Instructions on", and "Instructions off"
"Day colours", and "Night colours"
"2D view", and "3D view"
"Zoom in", and "Zoom out"
Saying commands in different ways
Your TRUCKER recognises many more words than just the ones you see in the list of commands, so
try some of your own words. You can say other words that have the same meaning, for example you
can say the following words:
"OK", "Correct" or "Right" instead of "Yes" when you want to confirm what you said.
74
"Navigate to", "Look for" or "Nearest" instead of "Drive to" when you want to drive to a petrol
station.
"Cancel" or "Delete" instead of "Clear" when you want to clear your current route.
Entering an address using voice control
Note: If spoken address entry is not supported in your current country, voice control is stopped
and the address entry screen is shown. You can enter the address in the normal way using the
keyboard.
The following example shows how to use voice control to plan a journey to an address or a location:
1. In map view or guidance view, say the wake-up phrase to start voice control.
The voice control screen is shown and your TRUCKER says "I'm listening". When voice control is
ready to listen, you see a microphone icon in the bottom left corner and you hear a beep.
2. Say "Go to an address" or "Go to a saved location".
Tip: Say "All commands" to see a list of commands you can say. Alternatively, select Help in
the Main menu, then select Voice control and then select Which commands can I say?.
For some commands, your TRUCKER repeats what you say and asks for confirmation.
3. If the command is correct, say "Yes."
If the command is incorrect, say "No" and repeat the command after you hear "I'm listening".
4. Say the address or location.
You can also say the name of a place or a city centre. Your TRUCKER repeats what you say and
asks for confirmation.
Important: Say "number one" or "number two" and not "one " or "two" when selecting an item
from a list such as a house number.
5. If the address or location is correct, say "Yes."
If the address or location is incorrect, say "No" and repeat the address after you hear "I'm
listening".
Tip: If you want to change the house number or street you can say "Change house number" or
"Change street".
Your TRUCKER plans a route from your current location to your destination.
Tip: To stop voice control, say "Cancel". To go back one step, say "Back".
Tip: Your TRUCKER recognises places and street names when they are spoken in the local
language using local pronunciation. You cannot enter postcodes using voice control.
Going to home using voice control
The following example shows how to use voice control to plan a journey to your home location:
1. In map view or guidance view, say the wake-up phrase to start voice control.
The voice control screen is shown and your TRUCKER says "I'm listening". When voice control is
ready to listen, you see a microphone icon in the bottom left corner and you hear a beep.
2. Say the command "Drive home".
Tip: Say "All commands" to see a list of commands you can say. Alternatively, select Help in
the Main menu, then select Voice control and then select Which commands can I say?.
75
For some commands, your TRUCKER repeats what you say and asks for confirmation.
3. If the command is correct, say "Yes."
If the command is incorrect, say "No" and repeat the command after you hear "I'm listening".
Your device plans a route from your current location to your home location.
Tip: To stop voice control, say "Cancel". To go back one step, say "Back".
Going to a POI using voice control
The following example shows how to use voice control to plan a journey to a petrol station:
1. In map view or guidance view, say the wake-up phrase to start voice control.
The voice control screen is shown and your TRUCKER says "I'm listening". When voice control is
ready to listen, you see a microphone icon in the bottom left corner and you hear a beep.
2. Say the command "Drive to a petrol station".
Tip: Say "All commands" to see a list of commands you can say. Alternatively, select Help in
the Main menu, then select Voice control and then select Which commands can I say?.
For some commands, voice control repeats what you say and asks for confirmation.
If a route is planned, a list of petrol stations along your route is shown. If a route isn't planned,
a list of petrol stations near your current location is shown.
3. Say the number of the petrol station you want to use, for example, "number three".
Voice control repeats what you say and asks for confirmation.
4. If the command is correct, say "Yes."
If the command is incorrect, say "No" and repeat the command after you hear "I'm listening".
Your TRUCKER plans a route from your current location to the petrol station.
Tip: To stop voice control, say "Cancel". To go back one step, say "Back".
Changing a setting using voice control
For example, to change the volume do the following:
1. In the map view, say the wake-up phrase to start voice control.
The voice control screen is shown and your TRUCKER says "I'm listening". When voice control is
ready to listen, you see a microphone icon in the bottom left corner and you hear a beep.
2. Say the command "Volume 50%".
Tip: Say "All commands" to see a list of commands you can say. Alternatively, select Help in
the Main menu, then select Voice control and then select Which commands can I say?.
For some commands, your TRUCKER repeats what you say and asks for confirmation.
3. If the command is correct, say "Yes."
If the command is incorrect, say "No" and repeat the command after you hear "I'm listening".
The volume on your TRUCKER changes to 50%.
Tip: To stop voice control, say "Cancel". To go back one step, say "Back".
76
About Map Share
You can report map corrections using Map Share. These map corrections are then shared with other
TomTom users when they receive a map update.
There are two ways to report a map correction:
Select a location on the map and create the correction report immediately.
Mark a location and create the correction report later.
To send your map correction reports to TomTom, you must connect your TRUCKER to your computer
and use MyDrive.
All map corrections reported by TomTom users are verified by TomTom. These verified corrections
are then sent back to your own TRUCKER as part of the next map update.
Tip: If a road closure is reported using Map Share, the closure is verified and immediately shown
by TomTom Traffic.
Creating a map correction report
Important: For safety reasons, do not enter the full details of a map correction while you are
driving. You can always mark the location and create the report later.
To create a map correction report, do the following:
1. Press and hold to select the location of the map correction on the map view.
2. Select the pop-up menu button to open the menu.
3. Select Report Map Error from the pop-up menu.
I
4. Select the type of map correction you want to apply.
Map Share
77
Note: If you want to report a map correction of a type not shown in the menu, use the Map
Share Reporter at tomtom.com.
5. Follow the instructions for your chosen type of map correction.
6. Select Report.
7. Connect your TRUCKER to MyDrive to send your map correction report to TomTom and receive
map corrections from other TomTom users.
Creating a map correction report from a marked location
If you see a map error while you are driving, you can mark the location so you can report the error
later.
Tip: You can mark your current location even when you are driving.
Important: Do not report map errors while you are driving.
1. In the map view or the guidance view, select the current location symbol or the speed panel.
The Quick Menu opens.
2. Select Mark Location.
The marked location is stored in My Places with the date and time you saved the location.
3. In the Main Menu, select My Places.
4. Open the Marked locations folder and select the marked location.
The marked location is shown on the map.
5. Select Report Map Error from the pop-up menu.
78
6. Select the type of map correction you want to apply.
Note: If you want to report a map correction of a type not shown in the menu, use the Map
Share Reporter at tomtom.com.
7. Follow the instructions for your chosen type of map correction.
8. Select Report.
The marker for the marked location is removed from the map.
9. Connect your TRUCKER to MyDrive to send your map correction report to TomTom and receive
map corrections from other TomTom users.
Types of map correction
There are several types of map correction available.
Note: If you want to report a map correction of a type not described below, use the Map Share
Reporter at tomtom.com.
For all map corrections described below, you need to connect your TRUCKER to MyDrive to send
your map correction report to TomTom and receive map corrections from other TomTom users.
Road Restriction
Select this option to block or unblock a road. You can block or unblock the road in one or both
directions by doing the following:
1. Press and hold to select the location of the map correction on the map view.
2. Select the pop-up menu button to open the menu.
3. Select Report Map Error from the pop-up menu.
4. Select Road Restriction.
Select the road sign at either end of the road to change it from open to closed or vice versa.
5. Select Report.
Street Name
Select this option to correct an incorrect street name.
1. Press and hold to select the location of the map correction on the map view.
2. Select the pop-up menu button to open the menu.
3. Select Report Map Error from the pop-up menu.
4. Select Street Name.
79
5. Enter the correct street name.
6. Select Report.
Turn Restriction
Select this option to report incorrect road turn restrictions.
1. Press and hold to select the location of the map correction on the map view.
2. Select the pop-up menu button to open the menu.
3. Select Report Map Error from the pop-up menu.
4. Select Turn Restriction.
5. If the incorrect junction is shown, select Select another junction.
6. Select the approach direction.
The map rotates so that the direction you are coming from is shown at the bottom of the
screen.
7. Select the traffic signs in turn to change the turn restrictions for each road at the junction.
8. Select Report.
Speed Limit
Select this option to correct the speed limit on the map.
1. Press and hold to select the location of the map correction on the map view.
2. Select the pop-up menu button to open the menu.
3. Select Report Map Error from the pop-up menu.
4. Select Speed Limit.
5. Select the correct speed limit.
If the correct limit is not shown, scroll left or right through the available speed limits.
6. Select Report.
80
About speed cameras
The Speed Cameras service warns you about the following camera locations:
Fixed speed camera locations.
Mobile speed camera locations.
Mobile speed camera hotspots.
Average speed camera locations.
Speed enforcement zones.
Red light camera locations.
Traffic restriction cameras.
The Speed Cameras service also warns you about the following safety hazards:
Accident blackspot locations.
Traffic jams.
To get TomTom services on your TRUCKER, you must be connected to TomTom services and logged
in to a MyTomTom account.
Note: TomTom services are not available on all TRUCKER devices.
Note: TomTom services are not available in all countries or regions, and not all services are
available in all countries or regions. For more information on available services in each region, go
to tomtom.com/services.
Crossing into another area or country
When you drive into an area or country that does not permit speed camera warnings, your TRUCKER
switches the speed cameras service off. You will not receive speed cameras warnings in those areas
or countries.
Some areas or countries permit limited speed camera warnings, for example only warnings for fixed
cameras, or warnings for risk zones. Your TRUCKER automatically switches to give limited warnings
when you cross into those areas or countries.
Speed camera warnings
Speed camera warning sounds are played for the most common types of speed camera. To change
the way you are warned about speed cameras, select Sounds & Warnings in the Settings menu.
Warnings are given as you approach a speed camera. You are warned in several ways:
A symbol is shown in the route bar and on your route on the map.
Your distance to the speed camera is shown in the route bar.
You hear a warning sound as you get near the camera.
While you are approaching a camera or driving in an average speed check area, your speed is
monitored. If you drive more than 5 km/h or 3 mph over the speed limit the route bar turns red.
If you drive less than 5 km/h or 3 mph over the speed limit the route bar turns orange.
Tip: In the map view or guidance view, you can select a speed camera symbol in the route bar to
see the type of camera, the maximum speed and also the length of an average speed check area.
In the map view, you can also select a speed camera that is shown on your route.
Speed Cameras
81
Symbol shown on
map
Symbol shown in
route bar
Description
Fixed speed camera - this type of camera
checks the speed of passing vehicles and is fixed
in one place.
Mobile speed camera - this type of camera
checks the speed of passing vehicles and can be
moved to different locations.
Mobile speed camera hotspots - this type of
warning shows places where mobile cameras are
often used.
Average speed cameras - these types of
cameras measure your average speed between
two points. You are warned at the start and end
of the average speed check area.
While you are driving in an average speed check
area, your average speed is shown, instead of
your current speed. The distance to the end of
the area is shown in the route bar.
Speed enforcement zones - these zones can
contain multiple speed cameras.
You are warned at the start and end of a speed
enforcement zone. While you are driving in a
speed enforcement zone, your current speed is
shown, and the visual warning is shown in the
route bar.
Red light camera - this type of camera checks
for vehicles breaking traffic rules at traffic
lights. There are two types of traffic light
camera - those which check if you drive through
a red light and those which check for driving
through a red light together with speeding.
Traffic restriction - this type of warning warns
you about restricted roads.
Accident blackspot - this type of warning is
given for a place where road traffic accidents
have historically been concentrated.
You are warned at the start and end of the
accident blackspot. While you are driving in an
accident blackspot, your current speed is shown.
When you are in the blackspot, the visual
warning continues to be shown in the route bar.
Traffic jams - warnings are given in the route
bar for traffic jams.
82
Changing the way you are warned
To change the way you are warned about speed cameras, select the Sounds and Warnings button in
the Settings menu.
You can then set how you want to be warned for the different types of cameras and safety hazards.
You can change settings for whether you want to be warned, never warned or warned only if you
are speeding.
For example, to change how you are warned when you approach a fixed speed camera, do the
following:
1. Select Sounds and Warnings in the Settings Menu.
2. Select Speed camera warnings.
3. Select Fixed cameras.
4. Select one of the following warning options:
Always.
Only when speeding.
Never.
5. Select the back button.
Tip: To turn off all audible warnings, select Settings, followed by Sounds and Warnings and then
switch off Warning sounds.
Reporting a new speed camera
If you pass a new speed camera that you were not warned about, you can report it instantly.
Note: To report a speed camera, you must be connected to TomTom services and logged in to
your MyTomTom account.
You can report a speed camera in two ways:
Using the quick menu to report a speed camera
1. Select the current location symbol or the speed panel in the guidance view.
2. Select Report Speed Camera from the pop-up menu.
You see a message thanking you for adding the camera.
Tip: If you make a mistake when reporting a camera, select Cancel in the message.
The speed camera is saved on your TRUCKER automatically and also sent to other users.
Using the Main Menu to report a speed camera
1. Select the Main Menu button to open the Main Menu.
83
2. Select Report Speed Camera.
You see a message thanking you for adding the camera.
Tip: If you make a mistake when reporting a camera, select Cancel in the message.
The speed camera is saved on your TRUCKER automatically and also sent to other users.
Confirm or remove a mobile speed camera
You can confirm the presence of a mobile speed camera or remove a mobile speed camera if it is no
longer present.
1. Just after you pass a mobile speed camera, in the route bar you are asked if the camera was
still there.
2. Select Yes if the mobile speed camera is still there.
3. Select No if the mobile speed camera has been removed.
If you select No, the mobile speed camera is removed from your map.
Updating locations for cameras and hazards
The locations of speed cameras can change frequently. New cameras can also appear without
warning and the locations for other hazards, such as accident blackspots, may also change.
When connected to TomTom services, your TomTom TRUCKER receives all camera updates for fixed
and mobile camera locations in real time. You do not need to do anything to receive updates they
are sent to your TRUCKER automatically.
84
About danger zones and risk zones
The Danger Zones service warns you about danger zones and risk zones on your route when you are
in France.
Since 3rd January 2012, it has been illegal to receive warnings about the position of fixed or mobile
speed cameras when you are driving in France. To be compliant with this change in French law,
speed camera locations are no longer reported but instead areas of danger are indicated as danger
zones and risk zones.
Important: Outside of France, you receive warnings about speed cameras. Inside France, you
receive warnings about danger zones and risk zones. When you cross the border, the type of warning
you receive changes.
A danger zone is a zone specified by French law. A risk zone is a temporary danger zone reported by
users. The Danger Zones service warns you about both danger zones and risk zones in the same way.
Danger zones and risk zones may or may not contain one or more speed cameras or a range of other
driving hazards:
Specific locations are not available and a danger zone icon is shown instead as you approach the
zone.
The minimum length of the zone depends on the road type and is 300 m for roads in built-up
areas, 2000 m (2 km) for secondary roads and 4000 m (4 km) for motorways.
The location of one or more speed cameras, if any, can be at any point within the zone.
If two danger zones are close to each other, the warnings can be merged into a single longer
zone.
Information about the location of zones is continually updated by TomTom and other users and
frequently sent to your TRUCKER so that you always have the latest information. You can also
contribute by reporting new risk zone locations.
To get TomTom services on your TRUCKER, you must be connected to TomTom services and logged
in to a MyTomTom account.
Note: You cannot remove a danger zone or a risk zone.
Note: TomTom services are not available on all TRUCKER devices.
Note: TomTom services are not available in all countries or regions, and not all services are
available in all countries or regions. For more information on available services in each region, go
to tomtom.com/services.
Crossing into another area or country
When you drive into an area or country that does not permit speed camera warnings, your TRUCKER
switches the speed cameras service off. You will not receive speed cameras warnings in those areas
or countries.
Some areas or countries permit limited speed camera warnings, for example only warnings for fixed
cameras, or warnings for risk zones. Your TRUCKER automatically switches to give limited warnings
when you cross into those areas or countries.
Danger Zones
85
Danger zone and risk zone warnings
Warnings are given 10 seconds before you reach a danger zone or risk zone. You are warned in
several ways:
A symbol is shown in the route bar and on your route on the map.
Your distance to the start of the zone is shown in the route bar.
You hear a warning sound as you get near the start of the zone.
While you are approaching a zone or driving in a zone, your speed is monitored. If you drive
more than 5 km/h or 3 mph over the speed limit the route bar turns red. If you drive less than 5
km/h or 3 mph over the speed limit the route bar turns orange.
While you are driving in a zone your distance to the end of the zone is shown in the route bar.
Warning sounds are played for these types of zones:
Symbol shown on
map
Symbol shown in
route bar
Description
Danger zone - this type of warning is only given in
France.
You are warned at the start and end of the danger
zone.
Risk zone - this type of warning is only given in
France.
You are warned at the start and end of the risk
zone.
Traffic jams - warnings are given in the route bar
for traffic jams.
To change the way you are warned about danger zones and risk zones, select Sounds & Warnings in
the Settings menu.
Changing the way you are warned
To change the way you are warned about danger zones, select the Sounds and Warnings button in
the Settings menu.
You can change settings for whether you want to be warned or not.
For example, to change how you are warned when you approach a danger zone, do the following:
1. Select Sounds and Warnings in the Settings Menu.
2. Select Safety warnings.
3. Select Danger zones.
4. Select whether you always want to be warned or warned only when you are speeding. Select
Never to turn off the warning.
5. Select the back button.
Tip: To turn off all audible warnings, select Settings, followed by Sounds and Warnings and then
switch off Warning sounds.
86
Reporting a risk zone
If you pass a new temporary risk zone that you were not warned about, you can report it instantly.
Note: To report a risk zone, you must be connected to TomTom services and logged in to your
MyTomTom account.
If a new temporary risk zone is reported directly before or after an existing risk or danger zone,
then the new zone is added to the existing zone.
If enough Danger Zones users report a new risk zone, that zone may become a danger zone and be
available for all subscribers.
You can report a risk zone in two ways:
Using the quick menu to report a risk zone
1. Select the current location symbol or the speed panel in the guidance view.
2. Select Report Risk Zone from the pop-up menu.
You see a message thanking you for adding the risk zone.
Tip: If you make a mistake when reporting a risk zone, select Cancel in the message.
The risk zone is saved on your TRUCKER automatically and also sent to other users. A reported risk
zone stays on your device for three hours.
Using the Main Menu to report a risk zone
1. Select the Main Menu button to open the Main Menu.
2. Select Report Risk Zone.
You see a message thanking you for adding the risk zone.
Tip: If you make a mistake when reporting a risk zone, select Cancel in the message.
The reported risk zone is shown on your map and also sent to other users. A reported risk zone stays
active for three hours.
Updating locations for danger zones and risk zones
The locations of danger zones and risk zones can change frequently. New zones can also appear
without warning.
Your TomTom TRUCKER receives all zone updates in real time. You do not need to do anything to
receive updates they are sent to your TRUCKER automatically.
87
About My Places
My Places provides an easy way to select a location without the need to search for the location each
time. You can use My Places to create a collection of useful or favourite addresses.
Tip: The terms "favourite" and "place" mean the same thing - favourites are places that you go to
often.
The following items are always in My Places:
Home - Your home location can be your home address or somewhere you often visit. This
feature provides an easy way to navigate there.
Work - Your work location can be your workplace address or somewhere you visit often. This
feature provides an easy way to navigate there.
Recent destinations - Select this button to select your destination from a list of locations you
have recently used as destinations. These also include your stops.
Marked locations - You can mark a location and temporarily add it to My Places.
You can add a location to My Places directly in My Places, by selecting a location from the map, by
searching for a location or by marking a location.
Your home location, work location, marked locations and the locations that you have added appear
in a list in My Places and are shown with a marker on the map.
Setting your home and work locations
You can set your home and work locations in the following ways:
Setting your home or work location using My Places
1. In the Main Menu, select My Places.
2. Select Add Home or Add Work.
3. To select a location for home or work, do one of the following:
My Places
88
Zoom in on the map at the location you want to select. Press and hold to select the loca-
tion, then select the home or work location symbol.
Select the Search button and search for a location. Select a location to set as home or work.
Select Set home location or Set work location.
Setting your home or work location using the map
1. In the Map View, move the map and zoom in until you can see your home or work location.
2. Select the location by pressing and holding the screen for about one second.
A pop-up menu shows the nearest address.
1. Open the pop-up menu and select Add to My Places.
2. In the name bar, enter the name "Home" or "Work".
Note: "Home" must have a capital letter H and "Work" must have a capital letter W.
3. Select Add.
Your home or work location is shown on the map.
Changing your home location
You can change your home location in the following ways.
Changing your home location using My Places
1. In the Main Menu, select My Places.
2. Select Home.
Your home location is shown on the map, with a pop-up menu.
3. Select Edit Location.
4. To select a new home location, do one of the following:
Zoom in on the map at the location you want to select. Press and hold to select the loca-
tion, then select the home location symbol.
Select the Search button and search for a location. Select a location to set as home. Select
Set home location.
Changing your home location using the map
1. In the Map View, move the map and zoom in until you can see your new home location.
2. Select the location by pressing and holding the screen for about one second.
89
A pop-up menu shows the nearest address.
1. Open the pop-up menu and select Add to My Places.
2. In the name bar, enter the name "Home".
Note: "Home" must have a capital letter H.
3. Select Add.
Your home location is changed to the new location.
Adding a location from My Places
1. In the Main Menu, select My Places.
2. Select Add a new place.
3. To select a location, do one of the following:
Zoom in on the map at the location you want to select. Press and hold to select the loca-
tion, then select the add location symbol.
Search for a location. Select Show on Map, then select the add location symbol.
The name of the location appears in the edit screen.
4. Edit the name of the location so you can easily recognise it.
5. Select Done to save your location in the My Places list.
Add a location to My Places from the map
1. Move the map and zoom in until you can see the destination that you want to navigate to.
2. Press and hold to select the location.
3. Select the pop-up menu button.
4. Select Add to My Places.
The name of the location is shown in the edit screen.
5. Edit the name of the location so you can easily recognise it.
6. Select Done to save your location in the My Places list.
The location you added is shown with a marker on the map.
90
Adding a location to My Places using search
1. In the Main Menu, select Search.
2. Search for a location.
3. Select the location then select Show on map.
4. When the map view shows the location, select the pop-up menu button.
5. Select Add to My Places.
The name of the location appears in the edit screen.
6. Edit the name of the location so you can easily recognise it.
7. Select Done to save your location in the My Places list.
Adding a location to My Places by marking
To mark a location and temporarily add it to My Places, do the following:
1. Make sure that your current location is the location you want to mark.
2. Select the current location symbol or the speed panel in the guidance view to open the quick
menu.
3. Select Mark Location.
4. Once marked, the location is saved in My Places in the Marked Locations list.
If you want to permanently save a marked location, add it My Places by doing the following:
1. From the main menu, select My Places.
2. Select Marked Locations and choose your location from the list.
Your location is shown on the map.
3. Select Add to My Places from the pop-up menu.
The name of the location appears in the edit screen.
4. Edit the name of the location so you can easily recognise it.
5. Select Add.
Deleting a recent destination from My Places
1. In the Main Menu, select My Places.
2. Select Recent Destinations.
3. Select Edit List.
4. Select the destinations you want to delete.
5. Select Delete.
Deleting a location from My Places
1. In the Main Menu, select My Places.
2. Select Edit List.
3. Select the locations you want to delete.
4. Select Delete.
91
My Vehicle
Important: Route planning for a specific vehicle type is available only when a truck map is installed.
If a truck map is not installed, a car route is planned instead.
Select Settings in the Main Menu, then select My Vehicle.
On this screen, you can set your vehicle type and dimensions.
Routes planned by your device avoid restrictions for the vehicle type, and take into account the
vehicle's specifications.
Vehicle Type
Select this setting to choose your vehicle type. When you select your vehicle, the following
details for your vehicle are shown:
Length / Width / Height
Weight / Max. axle weight
Maximum speed
For vehicle types Car, Taxi, Van and Other, the dimensions, weights and maximum speed are set
to zero. To change a setting, select it and enter a value that is specific to your vehicle. You can
also leave a setting at zero so it will not be used to determine restrictions when a route is
planned.
For vehicle types Bus and Truck, pre-set dimensions, weights and maximum speed are shown. To
change a setting, select it and enter a value that is specific to your vehicle.
Important: Settings that are set at zero are not used to determine restrictions when a route is
planned.
HAZMAT
If your vehicle type is Truck and you are transporting hazardous materials, select this setting to
choose the type of hazardous material.
Appearance
Select Settings in the Main Menu, then select Appearance.
On this screen, you can change these settings:
Display
Select Display to change the appearance of the display.
Route bar
Settings
92
Select Route bar to change the information you see in the route bar.
Guidance view
Select Guidance view to change the information you see in the guidance view.
Automatic zoom
Select Automatic Zoom to change how you view a junction as you drive.
Automatic map view switching
By default, automatic changing of views is on. This means, for example, that your TRUCKER
shows the map view when an alternative route is being suggested, along with several other sets
of circumstances. Also, for example, that your TRUCKER shows the guidance view when you
start driving and you start to accelerate. Select this setting if you want to turn off automatic
changing between guidance view and map view.
Show previews of motorway exits
Select this setting to control the full screen preview when you approach motorway exits.
Display
Select Settings in the Main Menu, then select Appearance.
Theme colour
Select Theme colour to change the accent colour used in the menus, buttons and icons.
Brightness
Select Brightness to change the following settings:
Day brightness
Move the slider to adjust the brightness level of the screen during the day.
Night brightness
Move the slider to adjust the brightness level of the screen during the night.
Select Switch to night colours when dark to automatically switch to night colours when it gets
dark.
Size of text and buttons
Select Size of text and buttons to change the size of the text and the buttons you see on the
screen.
Note: This feature is only available on devices with a 6 inch / 15 cm or larger screen.
Drag the slider to change the text and button size to small, medium or large, then select Apply this
change. Your TRUCKER restarts and applies the change.
Route Bar
Select Settings in the Main Menu, then select Appearance.
Select Arrival information to change the arrival information you see in the route bar.
93
Select Route information to change the route information you see on the route bar.
Show current time
Select this setting to show the current time in the guidance view. When switched on, the current
time is shown at the bottom of the route bar.
Show wide route bar if possible
The wide route bar is not shown by default. You can select this setting to switch on the wide route
bar in the guidance view.
Note: The wide route bar can only be shown if the screen is wide enough.
When the wide route bar is shown, you see more information about your route. For example, you
see time and distance to traffic queues and more.
Arrival information
Select Arrival information to change the following settings:
Show remaining distance
Select this setting to show the remaining distance left to travel in the arrival information panel
during navigation.
Show remaining time
Select this setting to show the remaining time left to travel in the arrival information panel
during navigation.
Switch between distance and time automatically
Select this setting to control the automatic switching between remaining distance and remain-
ing time in the arrival information panel.
Show arrival information for
Use this setting to control whether you want to see information about the destination or the
next stop in the arrival information panel.
94
Tip: To find out where the different panels are in the guidance view or map view, see What's on
the screen.
Route Information
You can choose to see any of the following in the route bar:
Parking
Select this setting to see car parks and parking.
Petrol stations
Select this setting to see petrol stations on your route.
Stops
Select this setting to see stops on your route.
Rest areas
Select this setting to see rest areas on your route.
Guidance view
Select Settings in the Main Menu, then select Appearance.
Show current street name
This setting displays name of the street you driving along on the guidance view.
Guidance view style
Select this setting to choose from 3D or 2D versions of the guidance view. Both the 2D and 3D
guidance views move in your direction of travel.
Automatic Zoom
Select Settings in the Main Menu, then select Appearance.
Select Automatic zoom to change settings for the automatic zoom in Guidance view when you
approach a turn or a junction. Zooming in can make the turn or junction easier to drive.
Zoom in to next turn
All the turns and junctions on your route are shown zoomed in to the maximum level.
Based on road type
The turns and junctions on your route are shown zoomed in to the standard level for the type of
road you are on.
None
None of the turns and junctions on your route are shown zoomed in.
95
Voices
Select Settings in the Main Menu, then select Voices.
Choosing a voice
Select Choose a voice to change the voice that gives spoken directions and other route instructions.
A wide range of voices are available. There are computer voices which can read street names and
other information directly from the map and there are recorded voices which have been recorded
by actors.
Note: Computer voices are not available in all languages.
If you need a computer voice and your language is unavailable, then you are asked to choose from
a list of installed computer voices available for the country you are in.
Instruction settings
Read aloud early instructions
For example, if you switch on this setting, you could hear early instructions such as "'After 2 km
take the exit right" or "Ahead, turn left".
Note: When a recorded voice is chosen, you see only this setting because recorded voices
cannot read out road numbers, road signs, etc.
Read aloud road numbers
Use this setting to control whether road numbers are read aloud as part of navigation instruc-
tions. For example, when road numbers are read aloud, you hear "Turn left onto A100".
Read aloud road sign information
Use this setting to control whether road sign information is read aloud as part of navigation
instructions. For example, "Turn left onto A302 Bridge Street towards Islington."
Read aloud street names
Use this setting to control whether street names are read aloud as part of navigation instruc-
tions. For example, when street names are read aloud, you hear "Turn left Graham Road to-
wards Hackney."
Read aloud foreign street names
Use this setting to control whether foreign street names are read aloud as part of navigation
instructions, such as "Turn right Champs Élysées". For example, an English computer voice can
read and pronounce French street names but pronunciation may not be completely accurate.
Voice Control
Note: Voice control is not supported on all devices or in all languages.
Select Settings in the Main Menu, then select Voice Control.
Start voice control when I say "Hello TomTom"
Select this setting to start voice control when you say the wake-up phrase. The default wake-up
phrase is "Hello TomTom", but you can make your own wake-up phrase.
96
Change the wake-up phrase
Use this setting to make your own wake-up phrase.
Use voice to accept an alternative route
Use this setting to control the ability to accept an alternative route by using your voice. When
an alternative route can save you time, the number of minutes is also spoken and not just
shown on the screen.
Maps
Select Settings in the Main Menu, then select Maps.
Changing the map
Select Change map to change the map that you are using.
You can choose from maps stored either in internal memory or memory cards if your TRUCKER has a
memory card slot.
Note: Although you can store more than one map on your TRUCKER, you can only use one map at
a time for planning and navigation.
Route Planning
Select Settings in the Main Menu, then select Route Planning.
When a faster route is available
If a faster route found while you are driving, TomTom Traffic can replan your journey to use the
faster route. Select from the following options:
Always take the fastest route
Ask me so I can choose
Don't ask me
Always plan this type of route
The types of route you can choose from are as follows:
Fastest route - the route which takes the least time.
Shortest route - the shortest distance between the locations you set. This may not be the
quickest route, especially if the shortest route is through a town or city.
Most eco-friendly route - the most fuel-efficient route for your journey.
Winding route - the route with the most turns.
Avoid motorways - this type of route avoids all motorways.
Walking route - a route designed for making the journey on foot.
Bicycle route - a route designed for making the journey on a bicycle.
97
Avoid on every route
You can choose to avoid ferries and car shuttle trains, toll roads, carpool lanes, and unpaved roads.
Set how your TRUCKER should manage each of these road features when the device calculates a
route.
Carpool lanes are sometimes known as High Occupancy Vehicle Lanes (HOV) and are not present in
every country. To travel on these lanes, you may need to have more than one person in the car, for
example, or the car may need to use environmentally-friendly fuel.
Sounds and Warnings
Select Settings in the Main Menu, then select Sounds & Warnings.
On this screen, you can change sound and warning settings.
Warning type
Warning type
You can choose the type of warnings you want to hear when you are driving:
Read-aloud warnings
Hear spoken warnings and warnings sounds.
Warning sounds
Hear only warning sounds.
None
No warning sounds are given.
Speed camera warnings
Select Settings in the Main Menu, then select Sounds & Warnings.
Select Speed camera warnings. You can then set how you want to be warned for the different
types of cameras and safety hazards. You can change settings for advance warning time and
whether you want to be warned, never warned or warned only if you are speeding.
Safety warnings
Select Settings in the Main Menu, then select Sounds & Warnings.
Select Safety warnings. You can then set how you want to be warned for the different types of
danger zones and safety hazards. You can change settings for advance warning time and whether
you want to be warned, never warned or warned only if you are speeding.
98
Danger zones
This type of warning is only given in France where you are only warned about danger zones.
Accident blackspots
This type of warning is given for a place where road traffic accidents have historically been
concentrated.
Risk zones
This type of warning is only given in France where you are only warned about danger zones.
Traffic jams
Traffic jam warnings in the route bar are part of TomTom Traffic. You can choose never to be
warned or to be warned when approaching a jam too quickly.
When speeding
This warning is given as soon as you exceed the speed limit by more than 5 km/h or 3 mph.
When you are speeding, the speed panel also turns red in the guidance view.
Screen touch sounds
Select Settings in the Main Menu, then select Sounds & Warnings.
Switch on Screen touch sounds to hear a click when you select an item or touch a button. The click
sound means that your selection or touch has been understood.
Read aloud traffic warnings
Select Settings in the Main Menu, then select Sounds & Warnings.
Switch on Read aloud traffic warnings to hear spoken warnings about traffic on your route.
Language and Units
Select Settings in the Main Menu, then select Language & Units.
On this screen, you can change the following settings:
Language
You can see your currently selected language on this screen. Select this setting to change the
language used for all buttons and messages that you see on your TRUCKER.
When you change the language setting, the voice automatically changes and units are set to
automatic.
Country
99
You can see your currently selected country on this screen. Select this setting to change the
country. When you change the country, the time/date format, distance units and voice are
changed automatically. The list includes the countries from the maps currently installed on your
device.
Keyboards
Select this setting to choose from a list of available keyboards.
You use the keyboard to enter names and addresses, such as when you plan a route or search
for the name of a town or a local restaurant.
Units
Select this setting to choose the units used on your device for features such as route planning. If
you want the units to be set by the GPS, select Automatic.
Time and date
The time and date are automatically set by satellite clocks but you can change the format of
both the time and date using these settings.
System
Select Settings in the Main Menu, then select System.
On this screen, you can change these settings:
About
This is an information screen rather than a setting and shows you information about your
TomTom TRUCKER. You may be asked to go to this screen during a call to TomTom Customer
Support or you may need to enter information taken from this screen when using the TomTom
Shop.
Information includes: Serial number, Application version, Installed maps, Product certifications,
MyTomTom account details, Free space, Copyright, Licences.
Send information
Select this setting to control whether you are asked about sending information to TomTom
every time your TRUCKER starts.
Battery settings
Select this setting to control power saving options on your TRUCKER.
Reset
Select this setting to delete all your saved places and settings and restore the standard factory
settings to your TomTom TRUCKER. This includes the language, voice settings, warning settings
and theme.
This is not a software update and will not affect the version of the software application in-
stalled on your TRUCKER.
Help
Select Help from the Main Menu or the Settings menu.
On this screen, you can see the following information:
Voice control
100
Note: Voice control is not supported on all devices or in all languages.
Select this option to see the following information about voice control:
How to use voice control
Tips for using voice control
Which commands can I say?
About
See System.
More help
You can get further help by going to tomtom.com/support.
For warranty and privacy information, go to tomtom.com/legal.
101
Help
Select Help from the Main Menu or the Settings menu.
On this screen, you can see the following information:
Voice control
Note: Voice control is not supported on all devices or in all languages.
Select this option to see the following information about voice control:
How to use voice control
Tips for using voice control
Which commands can I say?
About
See System.
More help
You can get further help by going to tomtom.com/support.
For warranty and privacy information, go to tomtom.com/legal.
Getting Help
102
Finding product certification information on your device
To find product certification information, such as the ICASA-approved certification number, do the
following on your TRUCKER:
1. Select Settings in the Main Menu.
2. Select System.
3. Select About.
4. Select Legal information.
5. Select Certificates.
6. You then see the relevant product certification information for your TRUCKER, for example,
ICASA.
Product certification
103
About MyDrive Connect
MyDrive Connect is a desktop-based application that helps you manage the content and services of
your TomTom TRUCKER. For example, you can use MyDrive Connect to get map updates, software
updates or manage your MyTomTom account.
It is a good idea to frequently connect your TRUCKER to MyDrive Connect to ensure you always have
the latest updates.
Tip: We recommend using a broadband internet connection whenever you connect your TRUCKER
to MyDrive Connect.
Tip: If you have a compatible navigation device, you can also use TomTom MyDrive to set a
destination, share locations and favourites, and save your personal navigation information.
MyTomTom account
To download content and to use TomTom services, you need a MyTomTom account.
You can create an account using your computer in one of the following ways:
By selecting the Create account button at tomtom.com.
By selecting the green MyTomTom button at tomtom.com.
By going to tomtom.com/getstarted.
Alternatively you can create an account on your TRUCKER by selecting Traffic & Speed Cameras or
Traffic & Danger Zones for the first time in the main menu of your navigation device. To use this
method, your TRUCKER needs to be always connected or connected using your phone.
Important: Take care when choosing a country during account creation. The correct country is
needed if you make a purchase from the TomTom shop and it cannot be changed after the account
has been created.
Note: If you have more than one TomTom navigation device in use, you need a separate account
for each device.
Setting up MyDrive Connect
To get ready to use MyDrive Connect for the first time, do the following:
1. On your computer, open a web browser and go to tomtom.com/getstarted.
2. Click Get Started.
3. Click Download MyDrive Connect.
Follow the instructions on the screen.
4. When prompted, connect your TRUCKER to your computer using the USB cable supplied, then
switch your TRUCKER on.
Note: Use ONLY the USB cable supplied with your TRUCKER. Other USB cables may not work.
Updating using MyDrive Connect
104
Note: You cannot use the mount to connect your TRUCKER to your computer.
Note: You should plug the USB cable directly into a USB port on your computer and not into a
USB hub or USB port on a keyboard or monitor.
5. Enter the requested information for account creation, including your country.
When set-up is complete, a MyTomTom account is created and your TRUCKER is linked to that
account.
You can now access MyDrive Connect from the notification area on your desktop.
MyDrive Connect starts automatically after the account is created.
Tip: When you connect your TRUCKER to your computer, MyDrive Connect tells you if there are
any updates for your TRUCKER.
105
Important Safety Notices and Warnings
Global Positioning System (GPS) and Global Navigation Satellite System (GLONASS)
The Global Positioning System (GPS) and Global Navigation Satellite System (GLONASS) systems are
satellite-based systems that provide location and timing information around the globe. GPS is
operated and controlled by the Government of the United States of America, which is solely
responsible for its availability and accuracy. GLONASS is operated and controlled by the Government
of Russia, which is solely responsible for its availability and accuracy. Changes in GPS or GLONASS
availability and accuracy, or in environmental conditions may impact the operation of this device.
TomTom disclaims any liability for the availability and accuracy of GPS or GLONASS.
Safety messages
Use with care
Use of TomTom products while driving still means that you need to drive with due care and
attention.
Your device is intended to serve as a driving aid and is not a substitute for driving with due care and
attention. Always obey posted road signs and applicable laws. Distracted driving can be extremely
dangerous. Please do not operate this device in any manner that diverts a driver’s attention from
the road in an unsafe manner. TomTom recommends using the hands-free systems where available
and pulling over to a complete stop at a safe location in order to interact with the device.
Notice for oversized/commercial vehicles
If a truck map is not installed on this product then this product is intended for use only on cars and
light commercial vehicles without a trailer, because the product will not provide appropriate routes
for oversized and commercial vehicles, buses, or campers and recreational vehicles. If you are
operating one of those vehicle types, please visit tomtom.com to find an appropriate product with
maps containing height and weight restrictions.
Aircraft and hospitals
Use of devices with an antenna is prohibited on most aircraft, in many hospitals and in many other
locations. This device must not be used in these environments.
Safety messages
Please read and take note of the following important safety advice:
Check your tyre pressures regularly.
Service your vehicle regularly.
Medication can affect your riding or driving ability.
Always use seat belts if available.
Don’t drink and drive.
Most accidents happen less than 5 km / 3 miles from home.
Obey the rules of the road.
Always use your turn indicators.
Every 2 hours, take a break for at least 10 minutes.
Addendum
106
Keep your seat belts on.
Keep a safe distance from the vehicle in front.
Before setting off on a motorbike, fasten your helmet correctly.
When riding a motorbike, always wear protective clothing and equipment.
When riding a motorbike, be extra vigilant and always ride defensively.
Rating: DC5V, 1.2A
How TomTom uses your information
Information regarding the use of personal information can be found at tomtom.com/privacy.
Battery
This product uses a Lithium-Ion battery.
Do not use it in a humid, wet and/or corrosive environment. Do not put, store or leave your product
in a high temperature location, in strong direct sunlight, in or near a heat source in a microwave
oven or in a pressurised container, and do not expose it to temperatures over 122°F / 50°C. Failure
to follow these guidelines may cause the battery to leak acid, become hot, explode or ignite and
cause injury and/or damage. Do not pierce, open or disassemble the battery. If the battery leaks
and you come into contact with the leaked fluids, rinse thoroughly with water and seek medical
attention immediately. For safety reasons, and to prolong the lifetime of the battery, remove your
product from your vehicle when you are not driving and keep in a cool, dry place. Charging will not
occur at low (below 32°F / 0°C) or high (over 113°F / 45°C) temperatures.
Temperatures: Standard operation: 32°F / 0°C to 113°F / 45°C; short period storage: -4°F / -20°C
to 122°F / 50°C; long period storage: -4°F / -20°C to 95°F / 35°C.
Important: Before you switch on the device, let the device acclimatise to the standard operation
temperature range for at least 1 hour. Do not use the device outside of this temperature range.
Caution: Risk of explosion if battery is replaced by an incorrect type.
Do not remove or attempt to remove the non-user-replaceable battery. If you have a problem with
the battery, please contact TomTom customer support.
THE BATTERY CONTAINED IN THE PRODUCT MUST BE RECYCLED OR DISPOSED OF PROPERLY
ACCORDING TO THE LOCAL LAWS AND REGULATIONS AND ALWAYS KEPT SEPARATE FROM HOUSEHOLD
WASTE. BY DOING THIS YOU WILL HELP CONSERVE THE ENVIRONMENT. USE YOUR TOMTOM DEVICE
ONLY WITH THE SUPPLIED DC POWER LEAD (CAR CHARGER/BATTERY CABLE), AC ADAPTER (HOME
CHARGER), IN AN APPROVED CRADLE OR USING THE SUPPLIED USB CABLE TO CONNECT TO A
COMPUTER FOR BATTERY CHARGING.
If your device requires a charger, please use this device with the charger provided. For replacement
chargers, go to tomtom.com for information about approved chargers for your device.
The stated battery life is a maximum possible battery life. The maximum battery life will only be
achieved under specific atmospheric conditions. The estimated maximum battery life is based on an
average usage profile.
For tips on extending the battery life, see this FAQ: tomtom.com/batterytips.
107
CE marking
This equipment complies with the requirements for CE marking when used in a residential,
commercial, vehicular or light industrial environment, achieving all the appropriate provisions of
the relevant legislation in the EU.
R&TTE directive
Hereby, TomTom declares that TomTom products and accessories are in compliance with the
essential requirements and other relevant provisions of the EU Directive 1999/5/EC. The declaration
of conformity can be found here: tomtom.com/legal.
WEEE directive
The wheelie bin symbol on the product or its packaging indicates that this product shall not be
treated as household waste. In line with EU Directive 2012/19/EU for waste electrical and
electronic equipment (WEEE), this electrical product must not be disposed of as unsorted municipal
waste. Please dispose of this product by returning it to the point of sale or to your local municipal
collection point for recycling. By doing this you will help conserve the environment.
Triman logo
Pacemakers
Pacemaker manufacturers recommend that a minimum of 15cm / 6 inches be maintained between a
handheld wireless device and a pacemaker to avoid potential interference with the pacemaker.
These recommendations are consistent with independent research and recommendations by
Wireless Technology Research.
Guidelines for people with pacemakers
You should ALWAYS keep the device more than 15cm / 6 inches from your pacemaker.
You should not carry the device in a breast pocket.
Other medical devices
Please consult your physician or the manufacturer of the medical device, to determine if the
operation of your wireless product may interfere with the medical device.
Connected networks
Devices that contain a GSM module are intended for connection to the following networks:
GSM/GPRS 900/1800
108
EU Specific Absorption Rate (SAR) compliance
THIS WIRELESS DEVICE MODEL MEETS GOVERNMENT REQUIREMENTS FOR EXPOSURE TO RADIO WAVES
WHEN USED AS DIRECTED IN THIS SECTION
This GPS Navigation System is a radio transmitter and receiver. It is designed and manufactured not
to exceed the emission limits for exposure to radio frequency (RF) energy set by the Council of the
European Union.
The SAR limit recommended by The Council of the European Union is 2.0W/kg averaged over 10
grams of tissue for the body (4.0 W/kg averaged over 10 grams of tissue for the extremities - hands,
wrists, ankles and feet). Tests for SAR are conducted using standard operating positions specified
by the EU council with the device transmitting at its highest certified power level in all tested
frequency bands.
Exposure limits
This device complies with radiation exposure limits set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the radio frequency exposure limits, human proximity to
the antenna shall not be less than 20cm (8 inches) during normal operation.
Regulatory Compliance Mark
This product displays the Regulatory Compliance Mark (RCM) to show that it complies with relevant
Australian regulations.
Customer support contact (Australia and New Zealand)
Australia: 1300 135 604
New Zealand: 0800 450 973
Notice for New Zealand
This product displays R-NZ to show it complies with relevant New Zealand regulations.
Warning for Australia
The user needs to switch off the device when exposed to areas with potentially explosive
atmospheres such as petrol stations, chemical storage depots and blasting operations.
This document
Great care was taken in preparing this document. Constant product development may mean that
some information is not entirely up to date. The information in this document is subject to change
without notice.
TomTom shall not be liable for technical or editorial errors or omissions contained herein, nor for
incidental or consequential damages resulting from the performance or use of this document. This
document contains information protected by copyright. No part of this document may be
photocopied or reproduced in any form without prior written consent from TomTom N.V.
Model names
4FL50, 4FL60
109
SoundClear™ acoustic echo cancellation software © Acoustic Technologies Inc.
110
© 2015 TomTom. All rights reserved. TomTom and the "two hands" logo are registered trademarks of
TomTom N.V. or one of its subsidiaries. Please see tomtom.com/legal for limited warranty and end
user licence agreements applying to this product.
© 2015 TomTom. All rights reserved. This material is proprietary and the subject of copyright
protection and/or database rights protection and/or other intellectual property rights owned by
TomTom or its suppliers. The use of this material is subject to the terms of a licence agreement.
Any unauthorised copying or disclosure of this material will lead to criminal and civil liabilities.
SoundClear™ acoustic echo cancellation software © Acoustic Technologies Inc.
The software included in this product contains copyrighted software that is licensed under the GPL.
A copy of that licence can be viewed in the Licence section. You can obtain the complete
corresponding source code from us for a period of three years after our last shipment of this
product. For more information, visit tomtom.com/gpl or contact your local TomTom customer
support team via tomtom.com/support. Upon request, we will send you a CD with the corresponding
source code.
Copyright notices
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110

TomTom Trucker de handleiding

Categorie
Auto navigatiesystemen
Type
de handleiding
Deze handleiding is ook geschikt voor