Snap-on Mobile Payment Module
with Chip and PIN
User Guide
Zebra reserves the right to make changes to any product to improve
reliability, function, or design. Zebra does not assume any product liability
arising out of, or in connection with, the application or use of any product,
circuit, or application described herein. No license is granted, either
expressly or by implication, estoppel, or otherwise under any patent right or
patent, covering or relating to any combination, system, apparatus,
machine, material, method, or process in which Zebra products might be
used. An implied license exists only for equipment, circuits, and subsystems
contained in Zebra products.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Zebra Technologies Corporation
Lincolnshire, IL, USA
http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH
Corp. The Symbol logo is a registered trademark of Symbol
Technologies, Inc., a Zebra Technologies company.
© 2015 Symbol Technologies, Inc.
72-122356-05 Revision A — March 2015
1 2 3
DCR7X00-200R
Introduction
The DCR7X00-200R Snap-on Mobile Payment Module with Chip and PIN
smart card reader snaps onto the bottom of the MC70/MC75 mobile
computer to allow easy data capture with magnetic stripe cards, EMV
compliant Chip and PIN cards and personal identification number (PIN) entry
using a numeric keypad. This guide describes how to install and use the
module.
Installation
1. Align the module with the bottom of the MC70/75 and push up until the
locking tabs snap into place.
2. Pull on the module to ensure it is securely connected to the MC70/75.
Removal
To remove the module from the MC70/75, push in the bottom of the two
locking tabs and pull the module from the MC70/75.
Credit Card Transactions
Launch a transaction application on the MC70/75. In the application, select
Credit Card transaction.
Swipe the credit card through the magnetic stripe reader (MSR) slot,
orienting the magnetic stripe as shown. Data encoded on the credit card is
captured and, depending on the application, may display in an application
data field.
Debit Card Transactions
Launch a transaction application on the MC70/75. In the application, select
Debit Card transaction.
Swipe the debit card through the MSR slot, orienting the magnetic stripe as
shown. Data encoded on the debit card is captured and, depending on the
application, may display in an application data field.
Turn the MC70/75 over and present the keypad to the customer. The
customer enters their PIN following the instructions on the display.
Chip and PIN Transactions
Launch a transaction application on the MC70/75. In the application, select
Chip and PIN transaction.
Customer inserts the Chip and Pin card into the slot, orienting the card with
the contacts facing down and toward the DCR keypad.
Customer turns the MC70/75 over, and enters their PIN following the
instructions on the display.
Customer removes the card when transaction is complete.
Keypad
The back of the module contains a display and a numeric keypad for entering
data.
Display Messages
After connecting the module to the MC70/MC75 and an application opens
the COM port, the following displays:.
Line 1 indicates the model number and the firmware version. The firmware
version displays after the model number. In this example the firmware
version is 0.09.
Line 2 indicates the keyload state.
The follow messages may appear on the display:
NOTE The module only functions when attached to the MC70/
MC75.
NOTE Credit Card transactions will function without an
encryption key injected but will not function if a tamper
event occurs.
NOTE Swipe the card in either direction, from left to right, or right
to left. For best results, gently press down on the card
while swiping to ensure contact with the bottom of the slot.
NOTE Debit Card transactions will only function with an
encryption key injected. It will not function if a tamper
event occurs.
NOTE Swipe the card in either direction, from left to right, or right
to left. For best results, gently press down on the card
while swiping to ensure contact with the bottom of the slot.
NOTE Chip and PIN transactions will function without an
encryption key injected but will not function if a tamper
event occurs.
Key Description
Numeric
Used to enter PIN.
Cancel (Red)
Cancels the current transaction.
Clear (Yellow)
Clears the entered data.
Enter (Green)
Submits the entered data.
Display Operating Status
Blank Normal. Keys are loaded. Online keys are
loaded. Offline and online transactions are
available.
- Normal. Online keys not loaded. Offline
transactions are available.
* Return to Zebra for service.
Message Description
Line 1:
Line 2: Enter PIN
Instructs the user to enter their PIN.
Line 1: PIN
Line 2: ENT to Accept
Displays “*” as PIN is entered and instructs
the user to press enter key when done.
5 6 74
Internal Battery Maintenance
The device contains an internal battery that provides power to keep keyload
code in memory. The internal battery will maintain data for at least four years
from date of manufacture. Internal battery life can be extended by providing
external power to the device. When the device is not in use, place it in a
cradle or attached to an MC70/75 with the transaction application open.
Charging the MC70/75
You can charge the MC70/75 while the module is attached. Place the MC70/
75 with the module into a cradle to charge the MC70/75. Ensure that the
module is seated properly in the cradle or charging cable and that the MC70/
75 is properly mounted on top of the module. Failure to do so can cause the
MC70/75 to not charge properly. The MC70/75 Charging LED indicates that
the MC70/75 is charging. If the Charging LED is not flashing or on, reconnect
the module and place back into the cradle or charging cable.
Installing Secure Access Modules (SAM Cards)
To install a SAM card, place the module on a solid surface with the keypad
and LCD face-down. Remove screw securing the door to the module using a
T7 Torx® screwdriver. Using your fingernail or other suitable device, pry up
on the fingernail slot near the screw. Remove the door.
Insert up to three SAM cards into the appropriate SAM card slots. The
contacts on the SAM card must be facing down with the cut edge as shown.
Align the tabs on the door with the slot in the module and close the door.
Secure door to module with the screw removed eariler.
Troubleshooting
Maintenance
There are no user serviceable part in the module.
Service Information
If you have a problem using the equipment, contact your facility’s Technical
or Systems Support. If there is a problem with the equipment, they will
contact the Zebra Support at: http://www.zebra.com/support.
For guides and software go to: http://www.zebra.com/support.
Regulatory Information
This guide applies to Model Number DCR7X00-200R.
All Zebra devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Local language translations are available at the following website: http://
www.zebra.com/support.
Any changes or modifications to Zebra equipment, not expressly approved
by Zebra could void the user’s authority to operate the equipment.
For use only with Zebra approved and UL Listed mobile computers. Zebra
approved and UL Listed accessories and/or Zebra approved and UL Listed/
Recognized battery packs.
Declared maximum operating temperature 50ºC.
Power Supply
Use only a Zebra approved power supply output rated at 5.4 Vdc and
minimum 3A. The power supply shall be Listed to UL/CSA 60950-1; and
certified to IEC60950-1 and EN60950-1 with SELV outputs. Use of
alternative power supply will invalidate any approval given to this device and
may be dangerous.
Radio Frequency Interference Requirements-FCC
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements –
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this device is in compliance with all the
applicable Directives, 2004/108/EC, 2006/95/EC and 2011/65/EU. A
Declaration of Conformity may be obtained from http://www.zebra.com/DOC.
English: For EU Customers: All products at the end of their life must be returned to
Zebra for recycling. For information on how to return product, please go to: http://
www.zebra.com/weee.
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти
трябва да се връщат на Zebra за рециклиране. За информация относно
връщането на продукти, моля отидете на адрес: http://www.zebra.com/weee.
Français: Clients de l'Union Européenne : Tous les produits en fin de cycle de vie
doivent être retournés à Zebra pour recyclage. Pour de plus amples informations sur
le retour de produits, consultez : http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán
entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea
más información sobre cómo devolver un producto, visite: http://www.zebra.com/
weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer
Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo
ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per
informazioni sulle modalità di restituzione, visitare il seguen
te sito Web: http://
www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser
devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver o
produto, visite: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun
levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg http://
www.zebra.com/weee voor meer informatie over het terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y
zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów
znajduj¹ siê na stronie internetowej http://www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich
životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu
najdete na webové stránce: http://www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada
taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz
kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával
kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de
funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre
returnarea produsului, accesaţi: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti
podjetju Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite: http://
www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste
returneras till Zebra för återvinning. Information om hur du returnerar produkten finns
på http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen
palauttamisesta on osoitteessa http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de
er udtjent. Læs oplysningerne om returnering af produkter på: http://www.zebra.com/
weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής
τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες
πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση
http://www.zebra.com/weee στο Διαδίκτυο.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu
tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif
għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti
podjetju Zebra za reciklažo. Za informacije o vračilu izdelka obiščite: http://
www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby
ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení
výrobkov nájdete na: http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti
grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį,
rasite: http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā
atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu
Zebra, lūdzu, skatiet: http://www.zebra.com/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için
Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu
adresi ziyaret edin: http://www.zebra.com/weee.
NOTE If you are going to replace the MC70/75 battery, remove the
module from the MC70/75 before replacing the battery.
NOTE A Secure Access Module (SAM) card is not required for all
applications. If the applications require a SAM card, use the
procedures below to install into the module.
Charge LED
(center)
Symptom Cause Action
When connected
to the MC70/75
the module’s
display is blank.
Transaction application not
running.
On MC70/75, launch
application.
Application did not open
COM port to module.
Ensure that application
opens COM port prior
to transaction.
Tamper event has occurred. Contact system
administrator.
Internal battery discharged. Contact system
administrator.
CAUTION Do not tamper with the module, it will be rendered non-
operational.
SAM Card
Cut Edge
CAUTION Only use Zebra approved and UL Listed accessories,
battery packs and battery chargers.
Do NOT attempt to charge damp/wet mobile computers or
batteries. All components must be dry before connecting
to an external power source.
Waste Electrical and Electronic Equipment (WEEE)
-
1
-
2
in andere talen
- English: Zebra DCR7X00-200R Owner's manual
Gerelateerde artikelen
-
Zebra MC3000 de handleiding
-
-
-
Zebra CRDMC45-1000C de handleiding
-
-
-
-
-
-