Yamaha CLP-153SG de handleiding

Categorie
Synthesizer
Type
de handleiding
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
92-469 1
ENVIRONMENTAL ISSUES: Yamaha strives to pro-
duce products that are both user safe and environmentally
friendly. We sincerely believe that our products and the
production methods used to produce them, meet these
goals. In keeping with both the letter and the spirit of the
law, we want you to be aware of the following:
Battery Notice: This product MAY contain a small non-
rechargable battery which (if applicable) is soldered in
place. The average life span of this type of battery is ap-
proximately five years. When replacement becomes nec-
essary, contact a qualified service representative to per-
form the replacement.
Warning: Do not attempt to recharge, disassemble, or
incinerate this type of battery. Keep all batteries away
from children. Dispose of used batteries promptly and as
regulated by applicable laws. Note: In some areas, the
servicer is required by law to return the defective parts.
However, you do have the option of having the servicer
dispose of these parts for you.
Disposal Notice: Should this product become damaged
beyond repair, or for some reason its useful life is consid-
ered to be at an end, please observe all local, state, and
federal regulations that relate to the disposal of products
that contain lead, batteries, plastics, etc.
NOTICE: Service charges incurred due to lack of knowl-
edge relating to how a function or effect works (when the
unit is operating as designed) are not covered by the
manufacturer’s warranty, and are therefore the owners
responsibility. Please study this manual carefully and con-
sult your dealer before requesting service.
NAME PLATE LOCATION: The graphic below indi-
cates the location of the name plate. The model number,
serial number, power requirements, etc., are located on
this plate. You should record the model number, serial
number, and the date of purchase in the spaces provided
below and retain this manual as a permanent record of
your purchase.
PRODUCT SAFETY MARKINGS: Yamaha electronic
products may have either labels similar to the graphics
shown below or molded/stamped facsimiles of these
graphics on the enclosure. The explanation of these graph-
ics appears on this page. Please observe all cautions indi-
cated on this page and those indicated in the safety in-
struction section.
See bottom of Keyboard enclosure for graphic symbol markings
The exclamation point within the equi-
lateral triangle is intended to alert the
user to the presence of important oper-
ating and maintenance (servicing) in-
structions in the literature accompany-
ing the product.
The lightning flash with arrowhead
symbol, within the equilateral triangle,
is intended to alert the user to the pres-
ence of uninsulated “dangerous volt-
age” within the product’s enclosure that
may be of sufficient magnitude to con-
stitute a risk of electrical shock.
IMPORTANT NOTICE: All Yamaha electronic prod-
ucts are tested and approved by an independent safety
testing laboratory in order that you may be sure that when
it is properly installed and used in its normal and custom-
ary manner, all foreseeable risks have been eliminated.
DO NOT modify this unit or commission others to do so
unless specifically authorized by Yamaha. Product per-
formance and/or safety standards may be diminished.
Claims filed under the expressed warranty may be denied
if the unit is/has been modified. Implied warranties may
also be affected.
SPECIFICATIONS SUBJECT TO CHANGE: The
information contained in this manual is believed to be
correct at the time of printing. However, Yamaha reserves
the right to change or modify any of the specifications
without notice or obligation to update existing units.
Model _____________________________________
Serial No. __________________________________
Purchase Date ______________________________
SPECIAL MESSAGE SECTION
WARNING- When using any electrical or electronic prod-
uct, basic precautions should always be followed. These pre-
cautions include, but are not limited to, the following:
1. Read all Safety Instructions, Installation Instructions,
Special Message Section items, and any Assembly Instructions
found in this manual BEFORE marking any connections, in-
cluding connection to the main supply.
2. Main Power Supply Verification: Yamaha products are
manufactured specifically for the supply voltage in the area
where they are to be sold. If you should move, or if any doubt
exists about the supply voltage in your area, please contact
your dealer for supply voltage verification and (if applicable)
instructions. The required supply voltage is printed on the
name plate. For name plate location, please refer to the graphic
found in the Special Message Section of this manual.
3. This product may be equipped with a polarized plug
(one blade wider than the other). If you are unable to insert the
plug into the outlet, turn the plug over and try again. If the
problem persists, contact an electrician to have the obsolete
outlet replaced. Do NOT defeat the safety purpose of the plug.
4. Some electronic products utilize external power sup-
plies or adapters. Do NOT connect this type of product to any
power supply or adapter other than one described in the owners
manual, on the name plate, or specifically recommended by
Yamaha.
5. WARNING: Do not place this product or any other
objects on the power cord or place it in a position where any-
one could walk on, trip over, or roll anything over power or
connecting cords of any kind. The use of an extension cord is
not recommended! If you must use an extension cord, the
minimum wire size for a 25' cord (or less) is 18 AWG. NOTE:
The smaller the AWG number, the larger the current handling
capacity. For longer extension cords, consult a local electri-
cian.
6. Ventilation: Electronic products, unless specifically
designed for enclosed installations, should be placed in loca-
tions that do not interfere with proper ventilation. If instruc-
tions for enclosed installations are not provided, it must be
assumed that unobstructed ventilation is required.
7. Temperature considerations: Electronic products
should be installed in locations that do not significantly con-
tribute to their operating temperature. Placement of this prod-
uct close to heat sources such as; radiators, heat registers and
other devices that produce heat should be avoided.
8. This product was NOT designed for use in wet/damp loca-
tions and should not be used near water or exposed to rain. Exam-
ples of wet/damp locations are; near a swimming pool, spa, tub,
sink, or wet basement.
9. This product should be used only with the components
supplied or; a cart, rack, or stand that is recommended by the
manufacturer. If a cart, rack, or stand is used, please observe all
safety markings and instructions that accompany the accessory
product.
10. The power supply cord (plug) should be disconnected from
the outlet when electronic products are to be left unused for ex-
tended periods of time. Cords should also be disconnected when
there is a high probability of lightening and/or electrical storm
activity.
11. Care should be taken that objects do not fall and liquids are
not spilled into the enclosure through any openings that may exist.
12. Electrical/electronic products should be serviced by a
qualified service person when:
a. The power supply cord has been damaged; or
b. Objects have fallen, been inserted, or liquids have been
spilled into the enclosure through openings; or
c. The product has been exposed to rain: or
d. The product dose not operate, exhibits a marked change
in performance; or
e. The product has been dropped, or the enclosure of the
product has been damaged.
13. Do not attempt to service this product beyond that de-
scribed in the user-maintenance instructions. All other servicing
should be referred to qualified service personnel.
14. This product, either alone or in combination with an ampli-
fier and headphones or speaker/s, may be capable of producing
sound levels that could cause permanent hearing loss. DO NOT
operate for a long period of time at a high volume level or at a
level that is uncomfortable. If you experience any hearing loss or
ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period
before damage occurs.
15. Some Yamaha products may have benches and/or acces-
sory mounting fixtures that are either supplied as a part of the
product or as optional accessories. Some of these items are de-
signed to be dealer assembled or installed Please make sure that
benches are stable and any optional fixtures (where applicable) are
well secured BEFORE using. Benches supplied by Yamaha are
designed for seating only. No other uses are recommended.
INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,
AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.
IMPORTANT SAFETY INSTRUCTIONS
PLEASE KEEP THIS MANUAL
92-469-2
vii
20
Introduction
Thank you for choosing a Yamaha CLP-153SG Clavinova. Your Clavinova is a fine musical
instrument that employs advanced Yamaha music technology. With the proper care, your
Clavinova will give you many years of musical pleasure.
Yamaha’s AWM (Advanced Wave Memory) tone generator system offers rich, realistic voices.
Piano-like touch response — adjustable in 4 stages — provides extensive expressive control and out-
standing playability.
Dual play mode allows 2 voices to be played simultaneously.
Unique Clavinova Tone voice provides a fresh sound for new musical expression.
Damper pedal includes natural resonance effect for the piano voice, simulates the string and sound-
board resonance of acoustic pianos.
Metronome feature with variable tempo facilitates practice.
Record and play back anything you play on the keyboard (up to approximately 4,200 notes).
MIDI compatibility and a range of MIDI functions make the Clavinova useful in a range of advanced
MIDI music systems.
In order to make the most of your Clavinovas performance potential and features, we urge you
to read this Owners Manual thoroughly, and keep it in a safe place for later reference.
Your Clavinova is a fine musical instrument, and deserves the most careful treatment.
Observe the following points and your Clavinova will sound and look great for many years.
1 Never open the case and touch or tamper with the inter-
nal circuitry.
2 Always turn the POWER switch OFF after use, and
cover the keyboard with the dust cover provided.
3 Clean the cabinet and keys of your Clavinova only with
a clean, slightly damp cloth. A neutral cleanser may be
used if desired. Never use abrasive cleansers, waxes,
solvents or chemical dust cloths since these can dull or
damage the finish.
4 Never place any vinyl products on your Clavinova. Con-
tact with vinyl can cause irreversible damage to the
finish.
5 Install your Clavinova in a place that is away from di-
rect sunlight, excessive humidity or heat.
6 Never apply excessive force to the controls, connectors
or other parts of your Clavinova, and avoid scratching
or bumping it with hard objects.
Name Plate Location
The CLP-153SG name plate is located on the bottom
panel.
Taking Care Of Your Clavinova
21
Manual de instrucciones
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Español
English
Deutsch
Français
1
Contents
The Control Panel .................................................. 2
Connections ............................................................ 4
Selecting & Playing Voices.................................. 5
Playing the Demonstration Tunes...................... 5
The Dual Mode ........................................................ 6
Adjusting the Balance Between the
Dual-mode Voices ........................................ 6
Shifting a Dual-Mode Voice Up One Octave 6
Memorizing the Balance & Octave Shift
Settings......................................................... 6
Reverb ...................................................................... 7
Adjusting Reverb Depth................................ 7
Memorizing the Reverb Type & Depth
Settings......................................................... 7
Touch Sensitivity ................................................... 8
Memorizing the Touch Sensitivity Setting..... 8
The Pedals ............................................................... 9
Soft/Sostenuto (Left) Pedal........................... 9
Damper (Right) Pedal ................................... 9
Transposition .......................................................... 9
Pitch Control ......................................................... 10
Tuning Up ................................................... 10
Tuning Down............................................... 10
To Restore Standard Pitch ......................... 10
Memorizing the Pitch Control Setting ......... 10
The Metronome & Tempo Control ................... 11
The Metronome................................................ 11
Metronome Volume .................................... 11
Metronome Time Signature ........................ 11
Tempo Control ................................................. 11
Using the Recorder.............................................. 12
Recording......................................................... 12
Changing the Initial Settings ....................... 13
Erasing the Recorded Data ........................ 13
Playback .......................................................... 13
Fast Forward Playback ............................... 13
MIDI Functions...................................................... 14
A Brief Introduction to MIDI......................... 14
MIDI “Messages” Transmitted &
Received by the Clavinova
........................... 14
MIDI Transmit & Receive Channel
Selection ..................................................... 15
MIDI Transmit Transpose ........................... 15
Other MIDI Functions....................................... 16
Local Control ON/OFF ................................ 16
Program Change ON/OFF.......................... 16
Control Change ON/OFF ............................ 17
The Multi-Timbre Mode............................... 17
The MIDI Split & Left Local OFF Mode....... 18
Bulk Data Dump.......................................... 18
Factory Preset Recall.......................................... 19
Troubleshooting................................................... 19
Options & Expander Modules ........................... 19
Keyboard Stand Assembly ....................................i
MIDI Data Format.....................................................v
Specifications ..........................................................v
MIDI Implementation Chart ..................................vi
2
The Control Panel
POWER
B0A0G0F0E0D0C0B-1A-1
C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 G2 A2 B2 C3 D3 E3 F3 A3 B3 C4 D4 E4 F4F2 G3
1
F2 G3
PHONES Jacks
(Bottom Panel)
Left voice shift up key
(See page 6)
Pitch control keys
(See page 11)
Transpose keys
(See page 9)
Balance keys (See page 6)
2
3
45
69
7
8
RECORDER
PLAY REC DEMO
ORGAN
HARPSI-
CHORD
E. PIANO
CLAVINOVA
TONE
METRONOME
PIANO
MIDI/
TRANSPOSE
TEMPO
MASTER VOLUME
32 120 280
MIN MAX
REVERB
ROOM
HALL 1
HALL 2
COSMIC
RECORDER
PLAY REC DEMO
ORGAN
HARPSI-
CHORD
E. PIANO
CLAVINOVA
TONE
METRONOME
PIANO
MIDI/
TRANSPOSE
TEMPO
MASTER VOLUME
32 120 280
MIN MAX
REVERB
ROOM
HALL 1
HALL 2
COSMIC
1 [POWER] Switch
Press the [POWER] switch once to turn the power
ON, a second time to turn the power OFF. When the
power is initially turned ON, the [PIANO] voice selec-
tor LED will light.
2 [MASTER VOLUME] Control
The [MASTER VOLUME] control adjusts the vol-
ume (level) of sound produced by the Clavinova’s
internal stereo sound system. The [MASTER VOL-
UME] control also adjusts headphone volume when a
pair of headphones is plugged into the PHONES jack
(page 4).
3 [TEMPO] Control
This control adjusts the tempo of the CLP-153SG met-
ronome function as well as the playback tempo of the
recorder function. The tempo range is from 32 to 280
quarter-note beats per minute.
4 [REVERB] Button
The [REVERB] button selects a number of digital
reverb effects that you can use for extra depth and
expressive power. See page 7 for details.
5 [METRONOME] Button
Turns the metronome sound on and off. The
[TEMPO] control, above, is used to set the tempo of
the metronome sound. More precise tempo settings can
be achieved by using the [METRONOME] button and
the CLP-153SG keyboard as described on page 11.
6 Voice Selectors
The CLP-153SG has five voice selectors. Simply press
any of the voice selectors to select the corresponding
voice. The voice selector LED will light to indicate
which voice is currently selected.
The CLP-153SG also has a DUAL mode in which two
voices can be played simultaneously across the full
range of the keyboard — see page 6 for details.
NOTE
The PIANO voice is automatically selected
whenever the [POWER] switch is initially turned
ON.
7 RECORDER [PLAY] and [REC] Buttons
These buttons control the CLP-153SG recorder, letting
you record and play back just about anything you play
on the keyboard — up to a maximum of about 4,200
notes. See page 12 for details.
3
D6 E6 F6 G6 A6 B6 C7
G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6
Right voice shift up key
(See page 6)
Memory key
(See page 6, 7, 8, 10)
Soft/Sostenuto
pedal
Damper pedal
0
8
[DEMO] Button
Activates the demo playback mode in which you can
select playback of five pre-programmed demonstration
sequences. See page 5 for details.
9 [MIDI/TRANSPOSE] Button
The [MIDI/TRANSPOSE] button allows access to the
Clavinova’s TRANSPOSE function (to shift the pitch
of the entire keyboard up or down) and MIDI func-
tions. For details refer to “TRANSPOSITION” on
page 9, “TOUCH SENSITIVITY” on page 8, and
“MIDI FUNCTIONS” on page 14, respectively.
0 Pedals
The CLP-153SG’s soft/sostenuto (left) and damper
(right) pedals provide a range of expressive control
capabilities similar to the pedal functions on an acous-
tic piano. See page 9 for details.
The Music Stand
If you will be using sheet music with your
Clavinova, raise the music stand built into its top
panel by lifting the rear edge of the music stand, then
flip down the music stand braces and engage them
with the corresponding recesses.
The music stand can be lowered after slightly lift-
ing it and folding the two brackets which support it
against the back of the stand.
4
AUX OUT
L/L+RR
Connections
2 AUX OUT L/L+R and R Jacks
Stereo System
These jacks are intended for use with an external tone generator module such as
the Yamaha DOU-10 Disk Orchestra Unit. The stereo outputs from the external
tone generator module are connected to the AUX IN L and R jacks, allowing the
sound of the tone generator to be reproduced via the Clavinova’s internal sound
system and speakers.
The AUX OUT L/L+R and R jacks deliver the output of the Clavinova for con-
nection to an instrument amplifier, mixing console, PA system, or recording equip-
ment. If you will be connecting the Clavinova to a monaural sound system, use
only the L/L+R jack. When a plug is inserted into the L/L+R jack only, the left-
and right-channel signals are combined and delivered via the L/L+R jack so you
don’t lose any of the Clavinova’s sound.
The Internal Amplifier & Speaker System
The CLP-153SG features a high-performance stereo amplifier delivering 20 watts per channel
to a pair of 16-cm speaker units.
NOTE
The AUX OUT jack signal must never be returned to the AUX IN jacks, either
directly or through external equipment.
The MIDI IN connector receives MIDI data from an external MIDI device (such
as the DOU-10 Disk Orchestra Unit) which can be used to control the Clavinova.
The MIDI OUT connector transmits MIDI data generated by the Clavinova (e.g.
note and velocity data produced by playing the Clavinova keyboard).
More details on MIDI are given in “MIDI FUNCTIONS” on page 14.
1 AUX IN L and R Jacks
3 MIDI IN and OUT Connectors
PHONES Jacks (Bottom Panel)
Two pairs of standard pair of stereo headphones can be plugged in here for pri-
vate practice or late-night playing. The internal speaker system is automatically
shut off when a pair of headphones is plugged into either of the PHONES jacks.
AUX IN
RL
DOU-10
MIDI
IN OUT
DOU-10
MIDI
IN
OUT
AUX IN
AUX OUT
RL
R L/L+R
123
5
ZTurn Power On
After making sure that the Clavinova’s AC plug is properly inserted into a
convenient AC wall outlet, press the [POWER] switch located to the left of the
keyboard to turn the power ON.
When the power is turned ON, the [PIANO] voice selector LED will light
(the PIANO voice is automatically selected whenever the power is turned ON).
Initially set the [MASTER VOLUME] control about half way between the
“MIN” and “MAX” settings. Then, when you start playing, re-adjust the [MAS-
TER VOLUME] control for the most comfortable listening level.
Select the desired voice by pressing one of the voice selectors.
The Clavinova offers keyboard touch response, so the volume and timbre of
notes played can be controlled according to how “hard” you play the keys. The
amount of variation available depends on the selected voice.
You can also add reverb as desired by using the [REVERB] button (see page 7
for [REVERB] button operation).
POWER
XSet the Volume
CSelect a Voice
ORGAN
HARPSI-
CHORDE. PIANO
CLAVINOVA
TONE
PIANO
MASTER VOLUME
MIN MAX
Selecting & Playing Voices
BAdd Reverb As Required
Press the [DEMO] button to engage the demo mode — the voice selectors
will flash in sequence.
Press one of the flashing voice selectors to start playback of the correspond-
ing demo tune — featuring the voice normally selected by that voice selector
button. The demo tunes will play in sequence until stopped, starting with the
selected tune. The voice selector indicator will flash during demo playback.
Use the [MASTER VOLUME] control to adjust the volume.
NOTE
The [TEMPO] control does not affect demo playback.
You can start playback of any other demo tune during playback by simply
pressing the corresponding voice selector. Playback will stop and the playback-
ready mode described in step 2, above, will be re-engaged if you press the voice
selector of the demo that is currently playing.
Press the [DEMO] button when you want to stop demo playback and return
to the normal play mode.
ZEngage the Demo Mode
DEMO
XSelect a Demo Tune
ORGAN
HARPSI-
CHORDE. PIANO
CLAVINOVA
TONE
PIANO
CSet the Volume
VPlay a Different Demo
B Stop the Demo
Playing the Demonstration Tunes
The CLP-153SG includes five demo tunes that effectively demonstrate its sound capabilities.
Here’s how you can select and play the demo tunes:
DEMO
MASTER VOLUME
MIN MAX
VPlay
The Demo Tunes
[PIANO] button: Etude op. 10-5 Black Keys by F. F. Chopin
[CLAVINOVA TONE] button: Pavane pour une infante défunte by M. J. Ravel
[HARPSICHORD] button: Le Coucou by L. C. Daquin
[ORGAN] button: Jesu, Joy Of Mans Desiring
(Chorale from Cantata No. 147)
by J. S. Bach
* The demonstartion pieces listed above are short excerpts from the original compositions.
The other demo tune is original (© 1995 by YAMAHA CORPORATION).
6
The Dual Mode
The DUAL mode makes it possible to play two voices simultaneously across the entire range
of the keyboard. To activate the DUAL mode simply press two voice selectors at the same time
(or press one voice selector while holding another). The voice indicators of both selected voices
will light when the DUAL mode is active. To return to the normal single-voice play mode, press
any single voice selector.
Adjusting the Balance Between
the Dual-mode Voices
The volume levels of the two voices combined in the DUAL mode
are normally set automatically to produce a pleasing balance (see
“Default Settings” below). The balance can be adjusted manually by
using the C2 through C4 keys on the keyboard while pressing the two
voice selectors corresponding to the voices to be combined in the
DUAL mode.
The C3 key produces equal (50:50) balance between the two
voices, while keys to the left of C3 increase the volume of the left
voice in relation to the right voice, and keys to the right of C3 in-
crease the volume of the right voice in relation to the left voice. By
“left” and “right” voice we refer to the relative positions of the voice
selectors — i.e. in a HARPSICHORD/ORGAN combination HARP-
SICHORD is the left voice and ORGAN is the right voice.
Default Settings
Voice Combinations Balance keys
PIANO/ORGAN ....................... F2
CLAVINOVA TONE/ORGAN ... F2
E. PIANO/ORGAN ................... F2
HARPSICHORD/ORGAN ........ G2
* All other voice combinations are set to C3 (equal balance).
Depending on which voices you combine using the DUAL mode,
the combination may sound better if one of the voices is shifted up an
octave. To shift the right voice, press the C5 key while pressing the
two voice selectors corresponding to the voices to be combined in the
DUAL mode. Press C5 again to shift the voice back to its normal
range. Use the C1 key in the same way to shift the left voice.
All voice combinations are set to the same octave by default.
Equal
balance.
Left voice
maximum.
Right voice
maximum.
C
3
C
2
C
4
ORGAN
HARPSI-
CHORDPIANO
Shifting a Dual-Mode Voice Up
One Octave
Left voice
shift up.
Right voice
shift up.
C
1
C
5
ORGAN
HARPSI-
CHORDPIANO
Memorizing the Balance &
Octave Shift Settings
Press the C7 key while holding any two voice selectors to memo-
rize all balance, and octave shift settings made since the power was
turned on. The memorized settings will be retained in memory for
about one week after the power is turned off, then the default settings
will be restored. To keep the memorized settings for longer periods,
turn the power on briefly at least once a week.
If these settings are not memorized as described above, they are
retained in memory only until the Clavinova is turned off.
C
7
ORGAN
HARPSI-
CHORDPIANO
7
Reverb
The [REVERB] button selects a number of digital reverb effects that you can use for extra depth and
expressive power.
To select a reverb type press the [REVERB] button a few times until the indicator corresponding to the
desired type lights (the indicators light in sequence each time the [REVERB] button is pressed). No reverb
is produced when all indicators are off.
OFF ............When no reverb effect is selected (no REVERB indicator is lit), a special natural
damper effect is applied to the piano voice. This simulates the natural resonance of
an acoustic piano’s strings and sound board when the damper pedal is pressed.
ROOM........This setting add a continuous reverb effect to the sound that is similar to the type of
acoustic reverberation you would hear in a medium-size room.
HALL 1 ......For a “bigger” reverb sound, use the HALL 1 setting. This effect simulates the natu-
ral reverberation of a medium-size concert hall.
HALL 2 ......For a really spacious reverb sound, use the HALL 2 setting. This effect simulates the
natural reverberation of a large concert hall.
COSMIC ....The COSMIC reverb effect produces an echo-plus-reverb sound that can add life and
animation to your music.
Adjusting Reverb Depth
The depth of the selected reverb effect can be adjusted for the current
voice by using the C2 through C4 keys on the keyboard while holding the
[REVERB] button. The C3 key sets the “normal” depth for the selected
effect. Keys to the left of C3 decrease the reverb depth, while keys to the
right of the C3 key increase the reverb depth. Separate reverb settings can
be made for each effect and voice, and these settings are retained in
memory until the power is turned off. The depth of the natural damper ef-
fect is fixed.
Default Settings
Normal
depth.
Decrease
depth.
Increase
depth.
C
3
C
2
C
4
REVERB
ROOM
HALL 1
HALL 2
COSMIC
* All effect types set to C3 for all other voices.
* The default reverb type is ROOM.
Press the C7 key while holding the [REVERB] button to memorize the
current effect type and all depth settings made since the power was turned
on. The memorized settings will be retained in memory for about one week
after the power is turned off, then the default settings will be restored. To
keep the memorized settings for longer periods, turn the power on briefly at
least once a week.
If these settings are not memorized as described above, they are retained
in memory only until the Clavinova is turned off.
Memorizing the Reverb
Type & Depth Settings
C
7
REVERB
ROOM
HALL 1
HALL 2
COSMIC
ROOM HALL 1 HALL 2
COSMIC
PIANO G2 G2 G2 G2
ORGAN C3 C3 F3 E3
8
Four different types of keyboard touch sensitivity HARD, MEDIUM, SOFT or FIXED
can be selected to match different playing styles and preferences. The different touch sen-
sitivity settings are selected by using the [MIDI/TRANSPOSE] and [REVERB] buttons.
Touch Sensitivity
HARD (ROOM indicator) ...........The HARD setting requires the keys to be played quite hard to produce maxi-
mum loudness.
MEDIUM (HALL 1 indicator)......The MEDIUM setting produces a fairly “standard” keyboard response. This is
the initial factory default setting.
SOFT (HALL 2 indicator) ...........The SOFT setting allows maximum loudness to be produced with relatively
light key pressure.
FIXED (No indicator lit)..............All notes are produced at the same volume no matter how hard the keyboard is
played. This is an ideal setting for voices which normally have no keyboard
sensitivity (i.e. harpsichord and organ).
To select a touch sensitivity setting press the [REVERB] button a few
times while holding the [MIDI/TRANSPOSE] button until the indicator
corresponding to the desired setting lights.
Press the C7 key while holding the [MIDI/TRANSPOSE] and [RE-
VERB] button to memorize the current touch sensitivity setting. The
memorized setting will be retained in memory for about one week after the
power is turned off, then the default setting (MEDIUM) will be restored. To
keep the memorized setting for longer periods, turn the power on briefly at
least once a week.
If this setting is not memorized as described above, it is retained in
memory only until the Clavinova is turned off.
MIDI/
TRANSPOSE
REVERB
ROOM
HALL 1
HALL 2
COSMIC
Memorizing the Touch Sen-
sitivity Setting
C
7
MIDI/
TRANSPOSE
REVERB
ROOM
HALL 1
HALL 2
COSMIC
9
The Pedals
The CLP-153SG has two foot pedals that produce a range of expressive effects similar to
those produced by the pedals on an acoustic piano.
The [MIDI/TRANSPOSE] button and keys F#2 through F#3 on the keyboard are used for transposition.
ZPress and hold the [MIDI/TRANSPOSE] button.
XPress a key between F#2 and F#3 according to the desired amount of
transposition.*
CRelease the [MIDI/TRANSPOSE] button.
* Pressing the C3 key produces normal keyboard pitch. Pressing the key to
the left of C3 (B2) transposes the pitch of the keyboard down a semitone,
the next key to the left (Bb2) transposes down a whole tone (two semi-
tones), etc., down to the F#2 key which transposes down 6 semitones.
Upward transposition is accomplished in the same way using the keys to
the right of C3, up to F#3 which transposes up 6 semitones.
NOTE
Notes below and above the A-1 C7 of the Clavinova sound one oc-
tave higher and lower, respectively.
The Clavinovas TRANSPOSE function makes it possible to shift the pitch of the entire key-
board up or down in semitone intervals up to a maximum of six semitones. Transposing the
pitch of the Clavinova keyboard facilitates playing in difficult key signatures, and you can easily
match the pitch of the keyboard to the range of a singer or other instrumentalist.
Transposition
When the power is turned on the left pedal is set for soft pedal operation.
Pressing the soft pedal reduces the volume and slightly changes the timbre
of notes played.
The left pedal can be switched to sostenuto operation by pressing the
pedal while holding the [MIDI/TRANSPOSE] button. If you play a note or
chord on the keyboard and press the sostenuto pedal while the note(s) are
held, those notes will be sustained as long as the pedal is held (as if the
damper pedal had been pressed) but all subsequently played notes will not
be sustained. This makes it possible to sustain a chord, for example, while
other notes are played “staccato.” You can switch back to soft pedal opera-
tion at any time simply by pressing the pedal while holding the [MIDI/
TRANSPOSE] button again.
The damper pedal functions in the same way as a damper pedal on an
acoustic piano. When the damper pedal is pressed notes played have a long
sustain. When no REVERB effect is selected and a piano voice is selected,
the damper pedal also produces a special “resonance” that simulates the
ring of the strings and the sound board of an acoustic piano. Releasing the
pedal immediately stops (damps) any sustained notes.
Soft/Sostenuto (Left) Pedal
Soft/Sostenuto pedal
Damper (Right) Pedal
MIDI/
TRANSPOSE
C
3
F#
2
Normal
pitch.
Transpose
down.
Transpose
up.
F#
3
-5 -3 -1 0 +2 +4 +5
-6 -4 -2 +1
+3 +6
Damper pedal
10
Pitch Control
Tuning Up
ZTo tune up (raise pitch), hold the A-1 and B-1 keys simultaneously.
XPress any key between C3 and B3. Each time a key in this range is
pressed the pitch is increased by approximately 1.2 cents, up to a maxi-
mum of 50 cents above standard pitch.
CRelease the A-1 and B-1 keys.
ZTo tune down (lower pitch), hold the A-1 and A#-1 keys simultane-
ously.
XPress any key between C3 and B3. Each time a key in this range is
pressed the pitch is decreased by approximately 1.2 cents, up to a maxi-
mum of 50 cents below standard pitch.
CRelease the A-1 and A#-1 keys.
ZTo restore standard pitch (A3 = 440 Hz), hold the A-1, A#-1 and B-1
keys simultaneously.
XPress any key between C3 and B3.
CRelease the A-1, A#-1 and B-1 keys.
NOTE
The PITCH CONTROL function has no effect when LOCAL OFF is
active (see “MIDI FUNCTIONS,” page 14).
Pitch control makes it possible to tune the Clavinova over a ±50-cent range in approximately
1.2-cent intervals. A hundred cents equals one semitone, so the tuning range provided allows
fine tuning of overall pitch over a range of approximately a semitone. Pitch control is useful for
tuning the Clavinova to match other instruments or recorded music.
Tuning Down
C
3
B
3
A
-1
B
-1
A
-1
A#
-1
C
3
B
3
To Restore Standard Pitch
A
-1
B
-1
A#
-1
C
3
B
3
Memorizing the Pitch Con-
trol Setting
C
7
Press the C7 key while holding the A-1/B-1, A-1/A#-1, or A-1/A#-1/B-1
key combination to memorize the current pitch control setting. The memo-
rized setting will be retained in memory for about one week after the power
is turned off, then the standard pitch will be restored. To keep the memo-
rized setting for longer periods, turn the power on briefly at least once a
week.
If this setting is not memorized as described above, it is retained in
memory only until the Clavinova is turned off.
11
The Metronome & Tempo Control
The CLP-153SG built-in metronome is a convenient feature for practice, and it can also pro-
vide a solid rhythmic guide when recording using the Recorder feature, described below.
The Metronome
The metronome sound is turned on and off via the [METRONOME]
button. Press the [METRONOME] button so that its indicator lights to turn
the metronome on, then again so the indicator goes out to turn the metro-
nome off.
The volume of the metronome sound can be independently adjusted by
using the [TEMPO] control while holding the [METRONOME] button.
Sliding the control to the right increases the metronome volume.
The time signature of the metronome sound can be set by pressing the
appropriate voice selector button while holding the [METRONOME] but-
ton, as follows:
METRONOME
Metronome Volume
METRONOME
TEMPO
32 120 280
Key Tempo
A-1 32
A#-1 34
B-1 36
C0 38
C#040
D0 42
D#044
E0 46
F0 48
F#050
G0 52
Key Tempo
G#054
A0 56
A#058
B0 60
C1 62
C#164
D1 66
D#168
E1 70
F1 72
F#174
Key Tempo
G1 76
G#178
A1 80
A#182
B1 84
C2 86
C#288
D2 90
D#292
E2 94
F2 96
Key Tempo
F#298
G2 100
G#2 102
A2 104
A#2 106
B2 108
C3 110
C#3 112
D3 114
D#3 116
E3 118
Key Tempo
F3 120
F#3 122
G3 124
G#3 126
A3 128
A#3 130
B3 132
C4 134
C#4 136
D4 138
D#4 140
Key Tempo
E4 142
F4 144
F#4 146
G4 148
G#4 150
A4 152
A#4 154
B4 156
C5 158
C#5 160
D5 164
Key Tempo
D#5 168
E5 172
F5 176
F#5 180
G5 184
G#5 188
A5 192
A#5 196
B5 200
C6 204
C#6 208
Key Tempo
D6 212
D#6 216
E6 220
F6 224
F#6 232
G6 240
G#6 248
A6 256
A#6 264
B6 272
C7 280
Tempo/Key Chart
METRONOME
TEMPO
32 120 280
Tempo Control
The tempo of the metronome and recorder playback can be controlled in
two ways:
Use the panel [TEMPO] control to set the required tempo from 32 to
280 quarter-note beats per minute.
For more precise tempo settings press the appropriate key on the key-
board while holding the [METRONOME] button.
[METRONOME] + [PIANO] No accent (default)
[METRONOME] + [CLAVINOVA TONE] 2 time
[METRONOME] + [E. PIANO] 3 time
[METRONOME] + [HARPSICHORD] 4 time
[METRONOME] + [ORGAN] 6 time
Metronome Time Signature
ORGAN
HARPSI-
CHORDE. PIANO
CLAVINOVA
TONE
METRONOME
PIANO
12
Using the Recorder
The CLP-153SG recorder lets you record what you play on the keyboard and then play it back. This is a
useful adjunct to any keyboard study program, since it lets you hear exactly how you sound from the listen-
ers perspective. It can also be just plain fun.
The recorder actually records the following data:
Notes played Voice selection Dual mode voices Dual balance
Damper pedal Left pedal Tempo
(Initial setting only.)
Reverb type Reverb depth
Recording
Press the RECORDER [REC] button to engage the record ready mode
(recording does not actually start yet). The [REC] button indicator will
light.
Before actually beginning to record, select the voice you want to record
with (or voices if you will be using the dual mode). You might also want to
set the volume and tempo controls.
Recording will begin automatically as soon as you play a note on the
keyboard or press the [PLAY] button.
NOTE
If the metronome was on when you started recording, youll be able to
keep time with the metronome while recording, but the metronome
sound will not be recorded.
You can record up to a maximum of about 4,200 notes, depending on
pedal usage and other factors. The [REC] button indicator will begin to
flash when recorder memory is almost full, and recording will stop auto-
matically.
Press either the RECORDER [REC] or [PLAY] button to stop record-
ing.
Z
Engage the Record Ready
Mode
RECORDER
PLAY REC
X
Make All Necessary Initial
Settings
ORGAN
HARPSI-
CHORDE. PIANO
CLAVINOVA
TONE
PIANO
C Start Recording
VStop Recording
RECORDER
PLAY REC
13
The initial voice (including dual mode), damper pedal, soft pedal, and
tempo settings made in step 2 of the recording procedure are actually re-
corded by the CLP-153SG. These initial settings can be changed after the
recording is finished by pressing the [REC] button to engage the record
ready mode, making the required changes, and then pressing the [REC]
button again to exit from the record ready mode and register the changes. If
you do this, be careful not to press the [PLAY] button or a key on the key-
board, either of which will start recording and erase all previous recorded
data.
Changing the Initial Settings
The recorded data can be erased by first pressing the [REC] button to
engage the record ready mode, and then pressing the [PLAY] button twice
without recording any data.
Erasing the Recorded Data
Playback
To play back what you’ve recorded, simply press the RECORDER
[PLAY] button. Playback starts from the beginning of the recorded data,
and will stop automatically at the end of the recorded data. You can also
stop playback at any time by pressing the [PLAY] button.
NOTE
It is possible to play along on the keyboard during playback.
The playback volume and tempo can be adjusted by using the [MASTER
VOLUME] and [TEMPO] controls, respectively.
If the metronome is being used during playback, the metronome will stop
when playback is stopped.
The playback data is not transmitted via the MIDI OUT connector.
All recorder data will be retained in memory for about one week after the
power is turned off. If you want to keep your recorded data for longer
periods, turn the power on briefly at least once a week. It is also possible
to store it to an external MIDI storage device such as the Yamaha DOU-
10 Disk Orchestra Unit by using the Bulk Dump function described on
page 18.
When you want to locate a specific point in a recording you can quickly
move forward through the recording while monitoring the sound by press-
ing the [REC] button while holding the [MIDI/TRANSPOSE] button.
RECORDER
PLAY REC
Fast Forward Playback
MIDI/
TRANSPOSE
RECORDER
PLAY REC
14
DOU-10
Data Being Recorded
Playback Data
MIDI IN MIDI INMIDI OUTMIDI OUT
DOU-10
MIDI Cable
MIDI INMIDI OUT
A Brief Introduction to MIDI
MIDI, the Musical Instrument Digital Interface, is a world-standard com-
munication interface that allows MIDI-compatible musical instruments and
equipment to share musical information and control one another. This
makes it possible to create “systems” of MIDI instruments and equipment
that offer far greater versatility and control than is available with isolated
instruments. For example, most MIDI keyboards (including the Clavinova,
of course) transmit note and velocity (touch response) information via the
MIDI OUT connector whenever a note is played on the keyboard. If the
MIDI OUT connector is connected to the MIDI IN connector of a second
keyboard (synthesizer, etc.) or a tone generator (essentially a synthesizer
with no keyboard), the second keyboard or tone generator will respond
precisely to notes played on the original transmitting keyboard. The result is
that you can effectively play two instruments at once, providing thick multi-
instrument sounds.
This same type of musical information transfer is used for MIDI se-
quence recording. A sequence recorder can be used to “record” MIDI data
received from a Clavinova, for example. When the recorded data is played
back, the Clavinova automatically “plays” the recorded performance in
precise detail.
The examples given above really only scratch the surface. MIDI can do
much, much more. The CLP-153SG offers a number of MIDI functions that
allows it to be used in fairly sophisticated MIDI systems.
NOTE
Always use a high-quality MIDI cable to connect MIDI OUT to MIDI IN
terminals. Never use MIDI cables longer than about 15 feet, since cables
longer than this can pick up noise which can cause data errors.
MIDI Messages Transmitted
& Received by the Clavinova
Note and Velocity Data
This information tells the receiving keyboard or tone generator to play a certain note (specified by the MIDI
note number) at a certain dynamic level (specified by the MIDI velocity value). Note and velocity data is trans-
mitted by the Clavinova whenever a key is pressed, and the Clavinova’s internal AWM tone generator will
“play” the corresponding note(s) whenever note and velocity data is received from an external MIDI device.
Program Change Numbers
The CLP-153SG transmits a MIDI program change number between 0 and 4 when one of its voice selectors is
pressed. This normally causes the correspondingly numbered voice to be selected on a receiving MIDI device.
The Clavinova will respond in the same way, automatically selecting the appropriate voice when a MIDI pro-
gram change number is received. See “Program Change ON/OFF” on page 16 for information on turning pro-
gram change number reception and transmission ON or OFF.
Control Change Numbers
Control Change data representing Damper pedal operation is transmitted by the Clavinova whenever one of
these pedals is used. If the receiving device is a tone generator or another keyboard, it will respond in the same
way as the Clavinova’s internal tone generator when one of the pedals is used. The Clavinova also receives and
responds to the appropriate control change data. See “Control Change ON/OFF” on page 17 for information on
turning control change number reception and transmission ON or OFF.
The MIDI information (messages) transmitted and received by the
Clavinova are as follows:
MIDI Functions
Clavinova
Clavinova
15
MIDI/
TRANSPOSE
C
6
F#
5
F#
6
-6 -4 -2 +1
+3 +6
+5+4+20-1-3-5
DOU-10
Tone Generator
MIDI IN
MIDI IN
MIDI OUT
MIDI THRU
MIDI/
TRANSPOSE
C
1
D#
2
C
4
D#
5
1356810121315
2 4 7 9 11 14 16
1356810121315
2 4 7 9 11 14 16
E
5
MIDI Transmit & Receive
Channel Selection
The MIDI system allows transmission and reception of MIDI data on 16
different channels. Multiple channels have been implemented to allow se-
lective control of certain instruments or devices connected in series. For
example, a single MIDI sequence recorder could be used to “play” two
different instruments or tone generators. One of the instruments or tone
generators could be set to receive only on channel 1, while the other is set
to receive on channel 2. In this situation the first instrument or tone genera-
tor will respond only to channel-1 information transmitted by the sequence
recorder, while the second instrument or tone generator will respond only to
channel-2 information. This allows the sequence recorder to “play” two
completely different parts on the receiving instruments or tone generators.
In any MIDI control setup, the MIDI channels of the transmitting and
receiving equipment must be matched for proper data transfer. An “OMNI”
receive mode is also available, which allows reception on all 16 MIDI chan-
nels. In the OMNI mode it is not necessary to match the receive channel of
the receiving device to the transmit channel of the transmitting device (ex-
cept when receiving mode messages).
Setting the Clavinova MIDI Channels
ZPress and hold the [MIDI/TRANSPOSE] button.
XPress the key on the keyboard corresponding to the desired MIDI trans-
mit or receive channel.*
CRelease the [MIDI/TRANSPOSE] button.
* Keys C1 through D#2 on the keyboard are used to set the MIDI transmit
channel, and keys C4 through D#5 are used to turn the OMNI mode OFF
and set the MIDI receive channel as shown in the illustration to the left.
The E5 key sets the OMNI receive mode and basic receive channel 1.
NOTE
When the power is initially turned ON, MIDI receive is set to the OMNI
mode and the transmit channel is set to 1.
This function allows the MIDI note data transmitted by the Clavinova to
be transposed up or down in semitone increments by up to plus or minus 6
semitones. The pitch of the Clavinova itself is not affected.
Setting the MIDI Transpose Function
ZPress and hold the [MIDI/TRANSPOSE] button.
XPress the key on the keyboard corresponding to the desired amount of
transposition.*
CRelease the [MIDI/TRANSPOSE] button.
* Keys F#5 through F#6 on the keyboard are used to set the MIDI transmit
transpose function as shown in the illustration to the left.
NOTE
When the power is turned ON, MIDI transmit transpose is set to 0 (no
transposition).
MIDI Transmit Transpose
For setting the transmit
channel. (C1 ~ D#2)
For setting the receive
channel. (C4 ~ D#5)
(Set to receive on MIDI
channel 2)
For OMNI mode
Clavinova
(Set to receive on MIDI channel 1)
16
E. PIA
N
CLAVINOVA
TONE
PIANO
MIDI/
TRANSPOSE
CLAVINOVA
TONE
CLAVINOVA
TONE
MIDI Functions
Other MIDI Functions
The MIDI functions listed to the right are engaged by
holding down the [MIDI/TRANSPOSE] button and press-
ing the corresponding voice selector. Full details are given
in the following pages.
Function
CLP-153
SG
Voice Selector
Local Control ON/OFF [PIANO]
Program Change ON/OFF [CLAVINOVA TONE]
Control Change ON/OFF [E. PIANO]
Multi-Timbre Mode [HARPSICHORD]
MIDI Split & Left Local OFF [ORGAN]
MIDI FUNCTION CHART
“Local Control” refers to the fact that, normally, the Clavinova keyboard controls its internal tone generator,
allowing the internal voices to be played directly from the keyboard. This situation is “Local Control ON” since
the internal tone generator is controlled locally by its own keyboard.
Local control can be turned OFF, however, so that the Clavinova keyboard does not play the internal voices,
but the appropriate MIDI information is still transmitted via the MIDI OUT connector when notes are played on
the keyboard. At the same time, the internal tone generator responds to MIDI information received via the MIDI
IN connector.
When using the DOU-10 Disk Orchestra Unit with the Clavinova, for example, Local Control should be
turned OFF when recording using the DOU-10 voices only, and ON when recording the Clavinova voices while
listening to playback of the DOU-10 voices.
ZHold down the [MIDI/TRANSPOSE] button.
XPress the [PIANO] voice selector. If the PIANO LED is lit when the
[PIANO] voice selector is pressed, you have turned local control OFF.
If the PIANO LED is not lit when the [PIANO] voice selector is
pressed, you have turned local control ON.
CRelease the [MIDI/TRANSPOSE] button.
Local Control ON/OFF
Normally the Clavinova will respond to MIDI program change numbers received from an external keyboard
or other MIDI device, causing the correspondingly numbered Clavinova voice to be selected. The Clavinova
will normally also send a MIDI program change number whenever one of its voices is selected, causing the cor-
respondingly numbered voice or program to be selected on the external MIDI device if the device is set up to
receive and respond to MIDI program change numbers.
This function makes it possible to cancel program change number reception and transmission so that voices
can be selected on the Clavinova without affecting the external MIDI device, and vice versa.
ZHold down the [MIDI/TRANSPOSE] button.
XPress the [CLAVINOVA TONE] voice selector. If the CLAVINOVA
TONE LED is lit when the [CLAVINOVA TONE] voice selector is
pressed, you have turned program change reception/transmission OFF.
If the CLAVINOVA TONE LED is not lit when the [CLAVINOVA
TONE] voice selector is pressed, you have turned program change
reception/transmission ON.
CRelease the [MIDI/TRANSPOSE] button.
Program Change ON/OFF
E. PIA
N
CLAVINOVA
TONE
PIANO
MIDI/
TRANSPOSE
PIANO
PIANO
= Local Control OFF
= Local Control ON
= Program Change OFF
= Program Change ON
17
E. PIANO
E. PIANO
MIDI/
TRANSPOSE
O
R
HARPSI-
CHORDE. PIANO
O
VA
Normally the Clavinova will respond to MIDI control change data received from an external MIDI device or
keyboard, causing the selected Clavinova voice to be affected by pedal and other “control” settings received
from the controlling device. The Clavinova also transmits MIDI control change information when one of its
pedals are operated.
This function makes it possible to cancel control change data reception and transmission if you do not want
the Clavinova voices to be affected by control change data received from an external device or vice versa.
Control Change ON/OFF
ZHold down the [MIDI/TRANSPOSE] button.
XPress the [E. PIANO] voice selector. If the E. PIANO LED is lit when
the [E. PIANO] voice selector is pressed, you have turned control
change reception/transmission OFF. If the E. PIANO LED is not lit
when the [E. PIANO] voice selector is pressed, you have turned control
change reception/transmission ON.
CRelease the [MIDI/TRANSPOSE] button.
The Multi-Timbre mode is a special mode in which the Clavinova voices
can be independently controlled on different MIDI channel numbers by an
external MIDI device. The Multi-Timbre mode can be activated as follows:
ZHold down the [MIDI/TRANSPOSE] button.
XPress the [HARPSICHORD] voice selector. If the HARPSICHORD
LED is lit when the [HARPSICHORD] voice selector is pressed, you
have turned the Multi-Timbre mode ON. If the HARPSICHORD LED
is not lit when the [HARPSICHORD] voice selector is pressed, you
have turned the Multi-Timbre mode OFF.
CRelease the [MIDI/TRANSPOSE] button.
The Multi-Timbre Mode
= Control Change OFF
= Control Change ON
MIDI/
TRANSPOSE
O
R
HARPSI-
CHORDE. PIANO
O
VA
HARPSI-
CHORD
HARPSI-
CHORD
= Multi-Timbre Mode ON
= Multi-Timbre Mode OFF
18
MIDI/
TRANSPOSE
ORGAN
HARPSI-
CHORD
P
IANO
MIDI Functions
In the MIDI split mode one section of the Clavinova keyboard is used to play a Clavinova voice in the normal
way, while the remaining section is used to play a second MIDI keyboard or tone generator such as the Yamaha
DOU-10 Disk Orchestra Unit. In this mode the right-hand section of the keyboard is used to play an internal
Clavinova voice, while the left-hand section of the keyboard plays the external keyboard or tone generator.
Playing the left-hand section of the keyboard produces no sound from the Clavinova. The “split point,” or the
key that divides the left- and right-hand sections of the keyboard can be set at any desired key.
The MIDI Split & Left Local OFF Mode
The MIDI split mode is useful if, for example, you want to play a piano
(Clavinova) voice with the right hand while playing a synthesizer bass line
or string section with the left hand.
When the MIDI split mode is activated, notes played on the left-hand
section are transmitted via the Clavinova MIDI OUT connector on MIDI
channel 2. Notes played on the right-hand section are transmitted on the
“basic channel” (i.e. the channel set using the MIDI channel selection func-
tion described previously).
ZPress the [ORGAN] voice selector while holding down the [MIDI/
TRANSPOSE] button. The ORGAN LED will flash.
XWhile still holding the [MIDI/TRANSPOSE] button, press the key on
the keyboard at which you want to set the split point. The ORGAN
LED will light continuously. The split-point becomes the first key of
the left-hand section.
CRelease the [MIDI/TRANSPOSE] button.
VTo return to the normal full-keyboard mode, hold the [MIDI/TRANS-
POSE] button and press the [ORGAN] voice selector, then release both
buttons.
NOTE
When the power is turned ON the default split point key F
#
2 will be
automatically selected. If a new split point is selected it remains active
until the power is turned OFF or a different split point is selected.
Left-hand section plays
a DOU-10 bass voice.
Right-hand section plays a
Clavinova piano voice.
SPLIT POINT
Bulk Data Dump
This function is used to transmit all data stored in the Recorder memory
to a MIDI data storage device such as the Yamaha DOU-10 Disk Orchestra
Unit, other sequence recorders, or MIDI compatible computers.
ZHold [MIDI/TRANSPOSE] and press the [PLAY] button. Transmis-
sion will begin.
XRelease the buttons.
NOTE
Bulk dump will not function when the metronome is on or when the re-
corder is in operation.
DOU-10
OUT PUT
R
L
AUX IN
L
RMIDI OUT
MIDI
IN
(Set to receive on
MIDI channel 2)
Clavinova
MIDI/
TRANSPOSE
RECORDER
PLAY REC
19
Factory Preset Recall
All dual mode, reverb, touch sensitivity, and pitch control settings can be
restored to their original factory preset values by holding the C7 key while
turning the [POWER] switch ON. This also erases all recorder data.
POWER
C
7
1. No Sound When the Power is Turned ON
Is the AC plug properly connected to an AC wall outlet? Check the AC connection carefully. Is the MASTER
VOLUME control turned up to a reasonable listening level?
This can occur if there is a high-power transmitter in your vicinity. Contact your Yamaha dealer.
This is usually due to turning ON or OFF a household appliance or other electronic equipment which is fed by
the same AC mains line as your Clavinova.
The Clavinova contains digital circuitry which can generate radio-frequency noise. The solution is to move the
Clavinova further away from the affected equipment, or vice versa.
If the Clavinova is connected to a stereo system or instrument amplifier and the sound is distorted, reduce the
setting of the Clavinova volume control to a level at which the distortion ceases.
Troubleshooting
If you encounter what appears to be a malfunction, please check the following
points before assuming that your Clavinova is faulty.
2. The Clavinova Reproduces Radio or TV Sound
3. Intermittent Static Noise
4. Interference Appears On Radio or TV Sets Located Near the Clavinova
5. Distorted Sound When the Clavinova is Connected to An External Amplifier/Speaker System
Options
BC-8 Bench
A comfortable bench styled to match your Yamaha Clavinova.
HPE-160 Stereo Headphones
High-performance lightweight dynamic headphones with extra-soft ear pads.
KC-883 Key Cover
A convenient way to keep your keyboard clean and dust-free.
Options & Expander Module
DOU-10 Disk Orchestra Unit
A range of MIDI recording and playback functions, plus Yamaha Disk Orchestra
Collection, Disklavier PianoSoft™, General MIDI, and Standard MIDI File disk
playback capability.
Expander Module
1
i
Keyboard Stand Assembly
NOTE
We do not recommend attempting to assemble the
Clavinova alone. The job can be easily accom-
plished, however, with only two people.
Use only the screws provided or replacements of
exactly the specified size. Using screws of the wrong
size can result in damage to the instrument.
Z Open the box and remove all the parts.
On opening the box you should find the parts shown in
the illustration above. Check to make sure that all the re-
quired parts are provided.
X
Attach the side panels (D) to the pedal
box (C).
Before installing the pedal box, untie and straighten out
the bundled cord attached to the bottom of the pedal box.
Place the pedal box on top of the wooden blocks at-
tached to the side panels (D), and attach using the four 6 x
25 millimeter round-head screws 1 — two screws on each
side. Make sure the pedals extend in the same direction as
the feet.
C
Attach the center panel (B) to the side
panels (D).
The center panel (B) should be screwed to the brackets
on the side panels (D) using the four 4 x 25 millimeter
round-head screws 2, as shown in the illustration. Make
sure the center panel is attached to the side of the brackets
facing the pedals.
A
B
C
D
HINWEIS
Wir raten davon ab, das Clavinova alleine
zusammenzubauen und aufzustellen. Zwei Personen
können diese Arbeit jedoch problemlos ausführen.
Verwenden Sie ausschließlich die mitgelieferten
Schrauben oder Ersatzschrauben identischer Größe.
Die Verwendung von Schrauben mit abweichenden
Maßen kann eine Beschädigung des Instruments zur
Folge haben.
Z
Öffnen Sie den Karton und nehmen Sie
alle Teile heraus.
Im Karton sollten die oben abgebildeten Teile enthalten
sein. Prüfen Sie zunächst bitte, ob alle Teile vollständig vor-
handen sind.
X
Schrauben Sie den Pedalkasten (C) an
den Seitenwänden (D) fest.
Bevor Sie den Pedalkasten montieren, nehmen Sie zu-
nächst das gebündelte Kabel aus dem Pedalkasten, entfernen
den Kabelbinder und ziehen das Kabel dann gerade aus.
Setzen Sie den Pedalkasten auf die Holzklötze an den
Seitenwänden (D), und schrauben Sie ihn dann mit den vier 6
x 25 mm Halbrundschrauben 1 fest (jeweils zwei Schrauben
links und rechts). Achten Sie dabei darauf, daß die Pedale in
dieselbe Richtung weisen wie die vorspringenden Teile der
Füße.
C
Schrauben Sie die Rückwand (B) an die
beiden Seitenwände (D).
Die Rückwand (B) wird mit den vier 4 x 25 mm Halbrund-
schrauben 2 an den Winkelblechen der Seitenwände (D)
festgeschraubt, wie in der Abbildung gezeigt. Achten Sie
bitte darauf, daß die Rückwand an den pedalseitigen Flächen
der Winkelbleche angebracht wird.
Zusammenbau und Aufstellung
6 x 25 mm round-head screws x 4 1
6 x 25 mm Halbrundschrauben x 4 1
Vis à tête ronde de 6 x 25 mm x 4 1
Tornillos de cabeza redonda
de 6 x 25 mm x 4 1
4 x 25 mm round-head screws x 4 2
4 x 25 mm Halbrundschrauben x 4 2
Vis à tête ronde de 4 x 25 mm x 4 2
Tornillos de cabeza redonda
de 4 x 25 mm x 4 2
6 x 16 mm flat-head screws x 4 3
6 x 16 mm Senkschrauben x 4 3
Vis à tête plate de 6 x 16 mm x 4 3
Tornillos de cabeza plana de
6 x 16 mm x 4 3
2 3
ii
Assemblage du support de clavier
REMARQUE
Nous ne vous conseillons pas d’essayer d’assembler
le Clavinova seul. Toutefois, ce travail peut être
facilement exécuté par deux personnes.
N’utilisez que les vis fournies ou des vis ayant
exactement les mêmes dimensions. L’utilisation de
vis de dimensions incorrectes pourrait endommager
l’instrument.
Z
Ouvrez le carton et retirez toutes les
pièces
Les pièces indiquées sur l’illustration devraient toutes se
trouver dans le carton. Vérifiez qu’il n’en manque aucune.
X
Fixez les panneaux latéraux (D) au
pédalier (C)
Avant de poser le pédalier, détacher le cordon de la
partie inférieure du pédalier et le dérouler.
Placez le pédalier sur les cales en bois fixées aux
panneaux latéraux (D) et fixez-le à l’aide des quatre vis à
tête ronde de 6 x 25 millimètres 1: deux vis de chaque
côté. Veillez à ce que les pédales soient dirigées dans le
même sens que les supports inférieurs.
C
Fixez le panneau central (B) aux
panneaux latéraux (D)
Le panneau central (B) doit être fixé aux ferrures des
panneaux latéraux (D) de la manière illustrée à l’aide des
quatre vis à tête ronde de 4 x 25 millimètres 2. Veillez à
ce que le panneau central soit fixé aux ferrures côté pédale.
Conjunto del soporte del teclado
NOTA
No le recomendamos que intente montar la
Clavinova usted solo. El trabajo puede ser realizado
fácilmente entre dos personas.
Utilice sólo los tornillos suministrados o reemplazos
del exacto tamaño especificado. El empleo de
tornillos de un tamaño erróneo puede dañar el
instrumento.
Z Abra la caja y extraiga todas las partes.
Al abrir la caja deberá encontrar todas las partes
mostradas en la ilustración. Compruebe para asegurarse
que se proporcionan todas las partes necesarias.
X
Acople los paneles laterales (D) en la
caja de pedales (C).
Antes de instalar la caja de pedales, desate y enderezca
el cable plegado unido a la parte inferior de la caja de
pedales.
Ponga la caja de pedales encima de los bloques de
madera unidos a los paneles laterales (D), y acople
empleando los cuatro tornillos de cabeza redonda de 6 x 25
mm 1; dos tornillos en cada lado. Asegúrese de que el
pedal se extiende en la misma dirección que la pata.
C
Acople el panel central (B) a los
paneles laterales (D).
EL panel central (B) debe enroscarse a las ménsulas de
los paneles laterales (D) usando los cuatro tornillos de
cabeza redonda de 4 x 25 mm 2 como se muestra en la
ilustración. Asegúrese de que el panel central se monta al
lado de las ménsulas encarado a los pedales.
C
D
B
4 x 25 mm round-head screws 2
4 x 25 mm Halbrundschrauben 2
Vis à tête ronde de 4 x 25 mm 2
Tornillos de cabeza redonda de 4 x 25 mm 2
C
D
6 x 25 mm round-head screws 1
6 x 25 mm Halbrundschrauben 1
Vis à tête ronde de 6 x 25 mm 1
Tornillos de cabeza redonda de 6 x 25 mm 1
4
V Install the main unit (A).
Place the main unit (A) on the side panels (D) with the
screws on its bottom panel (toward the rear of the main
unit) just behind the grooves in the brackets located at the
top of the side panels. Then slide the main unit forward
until it stops. WATCH YOUR FINGERS WHEN DO-
ING THIS!!
Align the holes on the bottom panel of the main unit
with the holes in the brackets on the side panels (also
center the main unit to produce equal clearance on the left
and right sides, as shown in the illustration), then screw in
and securely tighten the four 6 x 16 millimeter flat-head
screws 3.
B Connect the pedal cord.
Pass the pedal cord through the two cord holders on the
side panel. Plug the free end of the cord into the connector
on the bottom of the main unit (A). The plug only goes in
one way (the lug on the connector should face the key-
board-side of the main unit, as shown in the illustration) —
don’t try to force it in the wrong way around.
NSet the adjuster.
For stability, an adjuster is provided on the bottom of
the pedal box (C). Rotate the adjuster until it comes in firm
contact with the floor surface. The adjuster ensures stable
pedal operation and facilitates pedal effect control. If the
adjuster is not in firm contact with the floor surface, dis-
torted sound may result.
IMPORTANT
After assembling the Clavinova, check once more to
make sure that all screws have been securely fas-
tened.
If the stand leans to the side, makes unusual noises,
or otherwise seems unstable during use, check and
tighten all screws while following the assembly in-
structions given above.
V Montieren Sie die Tastatureinheit (A).
Setzen Sie die Tastatureinheit (A) so auf den fertigen
Ständer, daß die beiden Schrauben an ihrer Unterseite hinter
den Winkelblechen mit Führungsschlitz an der Hinterseite
des Ständers zu liegen kommen. Schieben Sie die Tastatur-
einheit dann bis zum Anschlag in die Schlitze. KLEMMEN
SIE IHRE FINGER DABEI NICHT EIN!!
Richten Sie die Schraubenbohrungen an der Unterseite der
Tastatureinheit mit den Bohrungen der Winkelbleche aus
(achten Sie auch darauf, daß sie mittig auf dem Ständer steht,
wie in der Abbildung gezeigt). Schrauben Sie die Tastatur-
einheit dann mit den vier 6 x 16 mm Senkschrauben 3 am
Ständer fest.
B Schließen Sie das Pedalkabel an.
Sichern Sie das Pedalkabel in den beiden Kabelhaltern an
den Seitenwänden. Der Stecker wird an die zugehörige
Buchse an der Unterseite der Tastatureinheit (A) angeschlos-
sen. Der Stecker paßt nur in einer Richtung in die Buchse
(mit der Führungsnase zur Tastaturseite des Instruments
weisend — siehe Abbildung). Versuchen Sie nicht, den Stek-
ker falsch herum mit Gewalt in die Buchse zu drücken!
N
Justieren Sie schließlich noch den
Höhenversteller.
Zur Stabilisierung ist an der Unterseite des Pedalkastens
(C) ein Höhenversteller vorgesehen. Schrauben Sie den
Höhenversteller heraus, bis er fest auf dem Fußboden steht.
Der Höhenversteller sorgt für stabile Pedalbetätigung und
ermöglicht eine präzise Regelung des Betätigungshubs.
Wenn er nicht fest auf dem Boden steht, können beim Treten
der Pedale Klangverzerrungen auftreten.
WICHTIG
Vergewissern Sie sich nach Zusammenbau und Auf-
stellung des Clavinova noch einmal davon, daß alle
Schrauben fest angezogen sind.
Wenn der Ständer schief steht, komische Geräusch
erzeugt oder sich beim Spielen wackelig anfühlt, prüfen
Sie gemäß den unter “Zusammenbau und Aufstellung”
gegebenen Anweisungen, ob der Ständer richtig
zusammengebaut wurde, und ziehen dabei die einzel-
nen Schrauben noch einmal nach.
iii
6 x 16 mm flat-head screws 3
6 x 16 mm Senkschrauben 3
Vis à tête plate de 6 x 16 mm 3
Tornillos de cabeza plana de 6 x 16 mm 3
D
A
A
D
5 6
V Posez le clavier (A)
Placez le clavier sur les panneaux latéraux (D), avec les
vis de son panneau inférieur (situées vers l’arrière du cla-
vier) placées immédiatement derrière les rainures des fer-
rures situées à la partie supérieure des panneaux latéraux
(D), puis faites glisser le clavier vers l’avant jusqu’à ce
qu’il vienne en butée. FAITES ATTENTION A VOS
DOIGTS EN EXECUTANT CETTE OPERATION!!
Alignez les trous du panneau inférieur du clavier sur les
trous des ferrures des panneaux latéraux (centrez égale-
ment le clavier de manière à avoir un jeu identique de cha-
que côté) puis posez et serrez à fond les quatre vis à tête
plate de 6 x 16 millimètres 3.
B Connectez le cordon du pédalier
Faites passer le cordon du pédalier dans les deux sup-
ports de cordon situés sur le panneau latéral. La prise doit
être branchée au connecteur correspondant situé à la partie
inférieure du clavier (A). La prise ne peut être branchée
que dans un seul sens (la languette de la prise doit être
dirigée vers l’avant du clavier, comme montré sur l’illus-
tration) et n’essayez donc pas de la forcer pour la mettre en
place du mauvais côté.
N
N’oubliez pas de régler la hauteur du
pédalier
Pour assurer la stabilité du pédalier (C), un dispositif de
réglage a été prévu à sa partie inférieure. Tournez ce dis-
positif jusqu’à ce qu’il soit en contact ferme avec la sur-
face du sol. Ce dispositif assure la stabilité du pédalier
lors de son utilisation et facilite la commande au pied des
effets. Si ce dispositif n’est pas en contact ferme avec le
sol, il pourra se produire une distorsion du son.
IMPORTANT
Après avoir assemblé le Clavinova, vérifiez une fois
de plus que toutes les vis sont bien serrées.
Si le support du clavier penche d’un côté, fait du bruit
ou semble instable lorsque vous utilisez l’instrument,
vérifiez de nouveau et resserrez toutes les vis en
suivant les instructions d’assemblage données ci-
dessus.
V Instale la unidad principal (A).
Coloque la unidad principal en los paneles laterales (D)
con los tornillos de su panel inferior (hacia la parte poste-
rior de la unidad principal) justo detrás de las ranuras de la
ménsula ubicada en la parte superior de los paneles latera-
les (D), después deslice el teclado hacia adelante hasta que
se pare. ¡TENGA CUIDADO CON SUS DEDOS MIEN-
TRAS LO HACE!
Alinee los orificios del panel inferior de la unidad prin-
cipal con los orificios de las ménsulas de los paneles late-
rales (también centre la unidad principal para producir una
holgura igual en los lados derecho e izquierdo, como se
muestra en la ilustración), después enrosque y apriete bien
los cuatro tornillos de cabeza plana de 6 x 16 mm 3.
B Conecte el cable de los pedales.
Pase el cable de los pedales a través de los dos soportes
de cable del panel lateral. La clavija puede enchufarse en
el conector correspondiente de la parte inferior de la uni-
dad principal (A). La clavija se enchufa sólo en una direc-
ción (la lengüeta del conector debe estar encarada hacia el
lado del teclado de la unidad principal, como se muestra en
la ilustración), por eso no la fuerce en la dirección errónea.
NAsegúrese de ajustar el ajustador.
Para la estabilidad del aparato, se proporciona un
ajustador en la parte inferior de la caja de pedales (C).
Gire el ajustador hasta que contacte firmemente con el
suelo. El ajustador asegura una operación estable de los
pedales y facilita el control del efecto de los pedales. Si el
ajustador no contacta firmemente con el suelo, puede re-
sultar en sonido distorsionado.
IMPORTANTE
Después de montar la Clavinova, compruebe otra
vez para asegurarse de que todos los tornillos se
han apretado bien.
Si el soporte se inclina hacia un lado, hace ruidos
anormales, o parece inestable durante la utilización,
compruebe y apriete todos los tornillos mientras
sigue las instrucciones de montaje de arriba.
iv
A
C
Cord holder
Kabelhalter
Support de cordon
Soporte del cable
A
Si vous êtes très familier avec l’interface MIDI ou si vous utilisez un
ordinateur pour commander votre matériel de musique au moyen de
messages MIDI générés par ordinateur, les données suivantes vous
seront utiles et vous aideront à commander le Clavinova.
SI usted está ya familiarizado con MIDI, o si emplea una
computadora para controlar sus aparatos musicales con mensajes MIDI
generados por computadora, los datos proporcionados en esta sección
le ayudarán a controlar la Clavinova.
1. NOTE ON/OFF
Data format: [9nH] -> [kk] -> [vv]
9nH = Note ON/OFF event (n = channel number)
kk = Note number
Transmit: 15 ~ 114 = D#-1 ~ F#7
Receive: 21 ~ 108 = A-1 ~ C7
vv = Velocity (Key ON = 1 ~ 127. Key OFF = 0)
Data format: [8nH] -> [kk] -> [vv]
8nH = Note OFF event (n = channel number)
kk = Note number
Transmit: 15 ~ 114 = D#-1 ~ F#7
Receive: 21 ~ 108 = A-1 ~ C7
vv = Velocity (Key OFF = 0 ~ 127)
* 8nH (note off) is receive only.
* 9nH (vv=00H) used for transmission.
2. CONTROL CHANGE & MODE MESSAGES
Data format: [BnH] -> [cc] -> [vv]
BnH = Control event (n = channel number)
cc = Control number
vv = Control value
cc
CONTROL
VALUE [vv]
07H Volume 00000000 : -
(reception only) 01101111 : -3dB
01111111 : ±0dB
0AH Pan Pot 00H ~ 17H LEFT 6
(reception only) 18H ~ 1FH 5
20H ~ 27H 4
28H ~ 2FH 3
30H ~ 37H 2
38H ~ 3FH 1
40H ~ 47H CENTER
48H ~ 4FH SCALING PAN
50H ~ 57H RIGHT 1
58H ~ 5FH 2
60H ~ 67H 3
68H ~ 6FH 4
70H ~ 77H 5
78H ~ 7FH 6
0BH Expression 00000000 : -
(reception only) 01101111 : -3dB
01111111 : ±0dB
40H Damper 00H ~ 3FH : OFF
Pedal 40H ~ 7FH : ON
42H Sostenuto 00H ~ 3FH : OFF
Pedal 40H ~ 7FH : ON
43H Soft Pedal 00H ~ 3FH : OFF
40H ~ 7FH: ON
5BH Reverb Depth 00H ~ 7FH : ON
(Sixteen levels)
78H
All Sound OFF (reception only)
00H
79H
Reset All Controller (reception only)
00H
7AH Local Control ON/OFF 00H : OFF
(reception only) 7FH : ON
7BH All Notes OFF (reception only) 00H
7CH Omni OFF/All Notes OFF 00H
(reception only)
7DH Omni ON/All Notes OFF 00H
(reception only)
3. PROGRAM CHANGE
Data format: [CnH] -> [pp]
CnH = program event (n = channel number)
pp = Program number
pp VOICE NAME pp VOICE NAME
00 PIANO 03 HARPSICHORD
01 CLAVINOVA TONE 04 ORGAN
02 E. PIANO
4. SYSTEM REALTIME MESSAGES
[rrH]
F8H: Timing clock
FAH: Start
FCH: Stop
FEH: Active sensing
Data Transmission Reception
F8H Transmitted every Received as 96-clock
96 clocks tempo timing when
MIDI clock is set to
External
FAH Recorder start Recorder start
FCH Recorder stop Recorder stop
FEH Transmitted every All notes are turned
200 milliseconds off if no data is
received for more than
400 milliseconds
*
Caution: If an overrun framing error occurs the
Damper, Sostenuto, and Soft effects for all chan-
nels are turned off and an All Note Off occurs.
If you’re already very familiar with MIDI, or are using a computer to
control your music hardware with computer-generated MIDI mes-
sages, the data provided in this section can help you to control the
Clavinova.
Falls Sie bereits mit MIDI vertraut sind oder einen Computer zur
Erzeugung von MIDI-Steuermeldungen für die Instrumente
verwenden, können Sie sich zur Steuerung des Clavinovas nach den
im folgenden Abschnitt aufgeführten Spezifikationen richten.
MIDI Data Format/MIDI-Datenformat/Format des données MIDI/Formato de datos MIDI
02H :
Dual On (Left voice 1 octave up)
03H :
Dual On (Right voice 1 octave up)
5CH Dual Voice [vv] : Dual Voice
* When cc=59 (Reverb), Clavinova common ID (01H)
is recognized in addition to 38H.
(4) Absolute Tempo
Data format: [F0H] -> [43H] -> [73H] -> [xx]
-> [11H] -> [1nH] -> [cc] -> [dd] -> [F7H]
43H : Yamaha ID
73H : Clavinova ID
xx : 38H (CLP-153SG ID)
11H : Clavinova special control
1nH : Control MIDI change
(Transmit: n=control channel number)
(Receive: any channel OK)
ccH : Absolute tempo low byte
ddH : Absolute tempo hight byte
Tempo=dd*128+cc
PANEL DATA SEND FORMAT
F0H, 43H, 0nH, 7CH, 00H, 1BH (n: channel number)
53H, 4BH, 20H, 20H (SK)
43H, 4CH, 50H, 27H, 39H, 34H (CLP ’94)
3xH, 3yH (x, y: version number)
[PANEL DATA]
[CHECK SUM (1byte)] =
0-(53H+4BH+20H+...+Data end)
F7H
• Panel Data Contents
(1) VOICE
(2) DUAL VOICE
(3) DUAL ON/OFF
(4) DUAL BALANCE
(5) 0
(6) 0
(7) 0
(8) REVERB NUMBER
(9) REVERB DEPTH
(10) TOUCH SENSITIVITY
(11) LEFT PEDAL (SOFT or SOSTENUTO)
(12) SPLIT POINT
(13) 0
(14) Absolute tempo low byte
(15) Absolute tempo high byte
NAME DATA SEND FORMAT
F0H, 43H, 0nH, 7DH, 00H, 10H (n: channel number)
53H, 4BH, 20H, 20H (SK)
43H, 4CH, 50H, 27H, 39H, 34H (CLP ’94)
3xH, 3yH, 20H, 20H, 20H, 20H (x, y: version number)
[CHECK SUM (1byte)] = 0-(53H+4BH+20H+......+20H)
F7H
BULK DUMP FORMAT
F0H, 43H, 73H
38H
(Product ID: CLP-153SG)
06H (Bulk ID)
02H (Bulk number)
0DH, 00H, 07H, 0CH
(Data length= wxyzH 0x683e*2 bytes)
[BULK DATA] (Sequence data)
[CHECK SUM (1byte)] = 0-sum (BULK DATA)
F7H
v
5. SYSTEM EXCLUSIVE MESSAGES
(1) YAMAHA MIDI Format
Data format: [F0H] -> [43H] -> [xn] -> [ff] ... [F7H]
43H : Yamaha
xn : Substatus + channel number.
ff : Format number.
xff Information
0 7CH
Panel Data receive.
2 7CH
Panel Data Send occurs when this data received.
2 7DH
Name Data Send occurs when this data received.
(2) Clavinova MIDI Format
Data format: [F0H] -> [43H] -> [73H] -> [xx]
-> [yy] -> [F7H]
43H : Yamaha ID
73H : Clavinova ID
xx : 38H (CLP-153SG ID)
yy : Substatus
yy Information
02H Internal MIDI clock.
03H External MIDI clock.
13H Multi-timbre mode OFF.
14H
Clavinova Common Voice multi-timbre mode ON.
15H Multi-timbre mode ON.
61H MIDI FA cancel ON.
62H MIDI FA cancel OFF.
7cH
All notes OFF; receive channel = c+1; omni OFF.
* When yy=2, 3, 13, 14, 15 or 7c, Clavinova com-
mon ID (01H) is recognized as well as 38H.
*
All Control Change values are reset when [13H],
[14H] or [15H] is received. All voices and other
parameters are also reset when [14H] or [15H] is
received in order to ensure the same initial settings.
(3) Special Control
Data format: [F0H] -> [43H] -> [73H] -> [xx]
-> [11H] -> [0nH] -> [cc] -> [vv] -> [F7H]
43H : Yamaha ID
73H : Clavinova ID
xx : 38H (CLP-153SG ID)
11H : Clavinova special control
0nH : Control MIDI change + channel number
cc : Control number
vv : Value
cc Control Value [vv]
08H
Dual Balance
00H : Left Voice Max.
7FH : Right Voice Max.
1BH Metronome 00H : Off
01H : On
26H Touch 00H : Medium
Sensitivity 01H : Soft
02H : Hard
03H : Off
59H Reverb 00H : Off
01H : Room
02H : Hall-1
03H : Hall-2
04H : Cosmic
5AH Dual Mode 00H : Dual Off
01H : Dual On (Normal)
Specifications/Technische Daten/
Caractéristiques techniques/Especificaciones
CLP-153SG
KEYBOARD 88 KEYS (A-1 ~ C7)
POLYPHONY 16 NOTES
VOICE SELECTORS PIANO, CLAVINOVA TONE, E. PIANO, HARPSHOCHORD, ORGAN
REVERB ROOM, HALL 1, HALL 2, COSMIC
TOUCH SENSITIVITY HARD, MEDIUM, SOFT, FIXED
RECORDER PLAY, REC
PEDAL CONTROLS SOFT/SOSTENUTO, DAMPER
OTHER CONTROLS MASTER VOLUME, TEMPO, METRONOME, DEMO, MIDI/TRANSPOSE
JACKS/CONNECTORS PHONES x 2, AUX OUT R & L/L+R, AUX IN R & L, MIDI IN/OUT
INPUT & OUTPUT AUX OUT: Output impedance 600
LEVEL/IMPEDANCE AUX IN: Input impedance 10 k/Input sensitivity -10 dBm
MAIN AMPLIFIERS 20W x 2
SPEAKERS 16 cm x 2
DIMENTIONS
(W x D x H) Music stand down:
1375 x 471.4 x 830.4 mm (54-1/8" x 18-1/2" x 32-3/4")
Music stand up:
1375 x 471.4 x 1007.5 mm (54-1/8" x 18-1/2" x 39-5/8")
WEIGHT 54.0 kg (119.0 lbs.)
*
Specifications subject to change without notice.
*
Änderungen ohne Vorankündigung vorbehalten.
* Sous toute réserve de modification des caractéristiques sans préavis.
* Especificaciones sujetas a cambios sin previo aviso.
MIDI Implementation Chart
vi
Not available
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions con-
tained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted
by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with
the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices. Compliance with these requirements provides a
reasonable level of assurance that your use of this product in a
residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the instruc-
tions found in the users manual, may cause interference harmful
to the operation of other electronic devices. Compliance with FCC
regulations does not guarantee that interference will not occur in
all installations. If this product is found to be the source of inter-
ference, which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker
or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the an-
tenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please
contact Yamaha Corporation of America, Electronic Service Divi-
sion, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed
by Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
M.D.G., EMI Division © Yamaha Corporation 1995
VT68500 507POCP2.301-A0 Printed in Japan
CANADA
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B”
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARA-
TUS SET OUT IN THE RADIO INTERFERENCE REGULATION OF
THE CANADIAN DEPARTMENT OF COMMUNICATIONS.
LE PRESENT APPAREIL NUMERIQUE N’EMET PAS DE BRUITS
RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES
AUX APPAREILS NUMERIQUES DE LA “CLASSE B” PRESCRITES
DANS LE REGLEMENT SUR LE BROUILLAGE RADIOELECTRI-
QUE EDICTE PAR LE MINISTERE DES COMMUNICATIONS DU
CANADA.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU
FOND.
• This applies only to products distributed by Yamaha Canada Music Ltd.
• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT. The wires in this mains lead are coloured in accor-
dance with the following code:
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured makings identifying the terminals
in your plug proceed as follows:
The wire which is coloured BLUE must be connected to the termi-
nal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of
the three pin plug.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31

Yamaha CLP-153SG de handleiding

Categorie
Synthesizer
Type
de handleiding