Yamaha CLP-555 Handleiding

Merk: Yamaha

Model: CLP-555

Categorie: Muziekinstrumenten

Type: Handleiding

Deze handleiding is ook geschikt voor

CLP555

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this

manual, meets FCC requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another

product use only high quality shielded cables. Cable/s supplied with this product

MUST be used. Follow all installation instructions. Failure to follow instructions

could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements

listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of assurance that your use of

this product in a residential environment will not result in harmful interference

with other electronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in the users

manual, may cause interference harmful to the operation of other electronic

devices. Compliance with FCC regulations does not guarantee that interference

will not occur in all installations. If this product is found to be the source of inter-

ference, which can be determined by turning the unit “OFF” and “ON”, please try

to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the

interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits

or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the

antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type

cable.

If these corrective measures do not produce satisfactory results, please contact

the local retailer authorized to distribute this type of product. If you can not

locate the appropriate retailer, please contact Yamaha Corporation of America,

Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by Yamaha

Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in accordance with the

following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond

with the coloured makings identifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the terminal which is

marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal of the three pin

plug.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG

TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE

LA PRISE ET POUSSER JUSQU’AU FOND.

• This applies only to products distributed by Yamaha Canada Music Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.

ENGLISH

DEUTSCHFRANÇAISESPAÑOL

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

IMPORTANT



Check Your Power Supply



Make sure that your local AC mains vol-

tage matches the voltage specified on

the name plate on the bottom panel. In

some areas a voltage selector may be

provided on the bottom panel of the

main keyboard unit near the power

cord. Make sure that the voltage selec-

tor is set for the voltage in your area.

The voltage selector is set at 240V

when the unit is initially shipped. To

change the setting use a “minus” screw-

driver to rotate the selector dial so that

the correct voltage appears next to the

pointer on the panel.



WICHTIG



Überprüfung der Stromversorgung



Vergewissern Sie sich vor dem Ansch-

ließen an das Stromnetz, daß die ör-

tliche Netzspannung den Betriebsspan-

nungswerten auf dem Typenschild an

der Unterseite des Instruments ents-

pricht. In bestimmten Verkaufsgebieten

ist das Instrument mit einem Span-

nungswähler an der Unterseite neben

der Netzkabeldurchführung ausgestat-

tet. Falls vorhanden, muß der Span-

nungswähler auf die örtliche Netzspan-

nung eingestellt werden. Der Span-

nungswähler wurde werkseitig auf 240

V voreingestellt. Zum Verstellen drehen

Sie den Spannungsregler mit einem

Schlitzschraubendreher, bis der Zeiger

auf den korrekten Spannungswert weist.



IMPORTANTE

Verifique la alimentación de corriente



Asegúrese de que tensión de alimenta-

ción de CA de su área corresponde con

la tensión especificada en la placa de

características del panel inferior de la

unidad del teclado principal, cerca del

cable de alimentación. Asegúrese de

que el selector de tensión esté ajustado

a la tensión de su área. El selector de

tensión se ajusta a 240V cuando la uni-

dad sale de fábrica. Para cambiar el

ajuste, emplee un destornillador de ca-

beza “recta” para girar el selector de

modo que aparezca la tensión correcta

al lado del indicador del panel.



IMPORTANT

Contrôler la source d’alimentation



Vérifiez que la tension spécifiée sur le

panneau arrière correspond à la tension

du secteur. Dans certaines régions, l’in-

strument peut être équipé d’un sélec-

teur de tension situé sur le panneau in-

férieur du clavier à proximité du cordon

d’alimentation. Vérifiez que ce sélec-

teur est bien réglé en fonction de la ten-

sion secteur de votre région. Le sélec-

teur de tension est réglé sur 240 V au

départ d’usine. Pour modifier ce ré-

glage, utilisez un tournevis à lame plate

pour tourner le sélecteur afin de mettre

l’indication correspondant à la tension

de votre région vis à vis du repère trian-

gulaire situé sur le panneau.



M.D.G., EMI Division © Yamaha Corporation 1997

VV62120 706POCP1.2-0310 Printed in Japan

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Nie-

derlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

For details of products, please contact your nearest Yamaha or the

authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha

ou au distributeur le plus proche de vous figurant dans la liste suivante.

ITALY

Yamaha Musica Italia S.P.A.,

Home Keyboard Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN

Yamaha-Hazen Electronica Musical, S.A.

Jorge Juan 30, 28001, Madrid, Spain

Tel: 91-577-7270

PORTUGAL

Valentim de Carvalho CI SA

Estrada de Porto Salvo, Paço de Arcos 2780 Oeiras,

Portugal

Tel: 01-443-3398/4030/1823

GREECE

Philippe Nakas S.A.

Navarinou Street 13, P.Code 10680, Athens, Greece

Tel: 01-364-7111

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1

Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Office

Generatorvej 8B

DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

Warner Music Finland OY/Fazer Music

Aleksanterinkatu 11, P.O. Box 260

SF-00101 Helsinki, Finland

Tel: 0435 011

NORWAY

Narud Yamaha AS

Grini Næringspark 17

N-1345 Østerås, Norway

Tel: 67 14 47 90

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120

IS-128 Reykjavik, Iceland

Tel: 525 5000

OTHER EUROPEAN COUNTRIES

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen, F.R. of

Germany

Tel: 04101-3030

ASIA

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 730-1098

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

16-28, Jalan SS 2/72, Petaling Jaya, Selangor,

Malaysia

Tel: 3-717-8977

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music Asia Pte., Ltd.

Blk 17A Toa Payoh #01-190 Lorong 7

Singapore 1231

Tel: 354-0133

TAIWAN

Kung Hsue She Trading Co., Ltd.

No. 322, Section 1, FuHsing S. Road,

Taipei 106, Taiwan. R.O.C.

Tel: 02-709-1266

THAILAND

Siam Music Yamaha Co., Ltd.

865 Phornprapha Building, Rama I Road,

Patumwan, Bangkok 10330, Thailand

Tel: 2-215-3443

THE PEOPLE’S REPUBLIC OF CHINA

AND OTHER ASIAN COUNTRIES

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2317

NORTH AMERICA

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America,

Keyboard Division

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MIDDLE & SOUTH AMERICA

MEXICO

Yamaha De Mexico S.A. De C.V.,

Departamento de ventas

Javier Rojo Gomez No.1149, Col. Gpe Del

Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.

Tel: 686-00-33

BRASIL

Yamaha Musical Do Brasil LTDA.

Ave. Reboucas 2636, São Paulo, Brasil

Tel: 011-853-1377

PANAMA

Yamaha De Panama S.A.

Edificio Interseco, Calle Elvira Mendez no.10,

Piso 3, Oficina #105, Ciudad de Panama, Panama

Tel: 507-69-5311

OTHER LATIN AMERICAN COUNTRIES

AND CARIBBEAN COUNTRIES

Yamaha Music Latin America Corp.

6101 Blue Lagoon Drive, Miami, Florida 33126,

U.S.A.

Tel: 305-261-4111

MIDDLE EAST

TURKEY/CYPRUS

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen,

F.R. of Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2312

EUROPE

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

IRELAND

Danfay Ltd.

61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin

Tel: 01-2859177

GERMANY/SWITZERLAND

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen,

F.R. of Germany

Tel: 04101-3030

AUSTRIA

Yamaha Music Austria

Schleiergasse 20, A-1100 Wien Austria

Tel: 0222-60203900

THE NETHERLANDS

Yamaha Music Nederland

Kanaalweg 18G, 3526KL, Utrecht, The Netherlands

Tel: 030-2828411

BELGIUM

Yamaha Music Belgium

Keiberg Imperiastraat 8, 1930 Zaventem, Belgium

Tel: 02-7258220

FRANCE

Yamaha Musique France,

Division Claviers

BP 70-77312 Marne-la-Valée Cedex 2, France

Tel: 01-64-61-4000

HEAD OFFICE Yamaha Corporation, Electronic Musical Instrument Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-3255

AFRICA

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2312

OCEANIA

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

17-33 Market Street, South Melbourne, Vic. 3205,

Australia

Tel: 3-699-2388

NEW ZEALAND

Music Houses of N.Z. Ltd.

146/148 Captain Springs Road, Te Papapa,

Auckland, New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2317

[CL] 9

92-469 1

ENVIRONMENTAL ISSUES: Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is ap-

proximately five years. When replacement becomes nec-

essary, contact a qualified service representative to per-

form the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the

manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and con-

sult your dealer before requesting service.

NAME PLATE LOCATION: The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these graph-

ics appears on this page. Please observe all cautions indi-

cated on this page and those indicated in the safety in-

struction section.

See bottom of Keyboard enclosure for graphic symbol markings

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing) in-

structions in the literature accompany-

ing the product.

The lightning flash with arrowhead

symbol, within the equilateral triangle,

is intended to alert the user to the pres-

ence of uninsulated “dangerous volt-

age” within the product’s enclosure that

may be of sufficient magnitude to con-

stitute a risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic prod-

ucts are tested and approved by an independent safety

testing laboratory in order that you may be sure that when

it is properly installed and used in its normal and custom-

ary manner, all foreseeable risks have been eliminated.

DO NOT modify this unit or commission others to do so

unless specifically authorized by Yamaha. Product per-

formance and/or safety standards may be diminished.

Claims filed under the expressed warranty may be denied

if the unit is/has been modified. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the specifications

without notice or obligation to update existing units.

SPECIAL MESSAGE SECTION

Model _____________________________________

Serial No. __________________________________

Purchase Date ______________________________

• Take care that the key cover does not pinch your fingers, and do not

insert a finger or hand in the key cover gap.

• Never insert or drop paper or metallic or other objects between the slits of

the key cover and the keyboard. If this happens, immediately turn off the

power and remove the electric plug from the outlet and have the instru-

ment inspected by qualified Yamaha service personnel.

• Do not place the instrument against a wall (allow at least 3 cm/one-inch

from the wall), since this can cause inadequate air circulation, and possi-

bly result in the instrument overheating.

• Read carefully the attached documentation explaining the assembly pro-

cess. Failure to assemble the instrument in the proper sequence might

result in damage to the instrument or even injury.

• Do not operate the instrument for a long period of time at a high or un-

comfortable volume level, since this can cause permanent hearing loss. If

you experience any hearing loss or ringing in the ears, consult a physi-

cian.

■USING THE BENCH (if included)

• Do not play carelessly with or stand on the bench. Using it as a tool or

step-ladder or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent the

possibility of accident or injury.

• Do not attempt to adjust the bench height while sitting on the bench,

since this can cause excessive force to be imposed on the adjustment

mechanism, possibly resulting in damage to the mechanism or even in-

jury.

• If the bench screws become loose due to extensive long-term use, tighten

them periodically using the included tool.

■SAVING USER DATA

• Save all data to an external device such as the Yamaha DOU-10 Disk

Orchestra Unit in order to help prevent the loss of important data due to a

malfunction or user operating error.

Yamaha cannot be held responsible for damage caused by improper use or modi-

fications to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep these precautions in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,

short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not open the instrument or attempt to disassemble the internal parts

or modify them in any way. The instrument contains no user-serviceable

parts. If it should appear to be malfunctioning, discontinue use immedi-

ately and have it inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill

into any openings.

• If the power cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the instrument, or if any unusual smells

or smoke should appear to be caused by it, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the instru-

ment inspected by qualified Yamaha service personnel.

• Only use the voltage specified as correct for the instrument. The required

voltage is printed on the name plate of the instrument.

• Before cleaning the instrument, always remove the electric plug from the

outlet. Never insert or remove an electric plug with wet hands.

• Check the electric plug periodically and remove any dirt or dust which

may have accumulated on it.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the

instrument or other property. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radia-

tors, and do not excessively bend or otherwise damage the cord, place

heavy objects on it, or place it in a position where anyone could walk on,

trip over, or roll anything over it.

• When removing the electric plug from an outlet, always hold the plug

itself and not the cord. Pulling by the cord can damage it.

• Do not connect the instrument to an electrical outlet using a multiple-

connector. Doing so can result in lower sound quality, or possibly cause

overheating in the outlet.

• Remove the electric plug from the outlet when the instrument is not to be

used for extended periods of time, or during electrical storms.

• Before connecting the instrument to other electronic components, turn off

the power for all components. Before turning the power on or off for all

components, set all volume levels to minimum.

• Do not expose the instrument to excessive dust or vibrations, or extreme

cold or heat (such as in direct sunlight, near a heater, or in a car during the

day) to prevent the possibility of panel disfiguration or damage to the

internal components.

• Do not use the instrument near other electrical products such as televi-

sions, radios, or speakers, since this might cause interference which can

affect proper operation of the other products.

• Do not place the instrument in an unstable position where it might acci-

dentally fall over.

• Before moving the instrument, remove all connected cables.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint

thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.

Also, do not place vinyl or plastic objects on the instrument, since this

might discolor the panel or keyboard.

• Gently remove dust and dirt with a soft cloth. Do not wipe too hard since

small particles of dirt can scratch the instrument’s finish.

• Bumping the surface of the instrument with metal, porcelain, or other hard

objects can cause the finish to crack or peel. Use caution.

• Do not rest your weight on, or place heavy objects on the instrument, and

do not use excessive force on the buttons, switches or connectors.

The Control Panel ...................................................4

Preparation ..............................................................6

■

The Music Stand.............................................6

■

The Key Cover ................................................6

■

Opening and Closing the Lid........................6

Connections .............................................................. 7

Selecting & Playing Voices....................................8

Playing the Demonstration Tunes........................9

■

Piano Song A-B Repeat...............................10

■

Piano Song Part Cancel ..............................11

●

Synchro Start ..........................................11

●

Left Pedal Start/Stop ...............................11

The Dual Mode ......................................................12

●

Other Dual Mode Functions ....................12

The Split Mode ......................................................13

●

Selecting the Left-hand Voice.................. 13

●

Setting the Split Point .............................. 13

●

Other Split Mode Functions.....................13

Reverb .................................................................... 14

●

Adjusting Reverb Depth .......................... 14

The Chorus Effect ..................................................15

●

Adjusting Effect Depth.............................15

The Pedals..............................................................15

●

Soft (Left) Pedal ...................................... 15

●

Sostenuto (Center) Pedal........................ 15

●

Damper (Right) Pedal..............................15

Touch Sensitivity ...................................................16

Transposition .........................................................16

Introduction

Thank you for choosing a Yamaha CLP-555

Clavinova. Your Clavinova is a fine musical

instrument that employs advanced Yamaha music

technology. With the proper care, your Clavinova

will give you many years of musical pleasure.

● Yamaha’s AWM (Advanced Wave Memory) tone

generator system offers rich, realistic voices. Both

models feature stereo sampling of the piano voices

for unmatched realism and expressive power.

● Piano-like touch response — adjustable in 4 stages

— provides extensive expressive control and

outstanding playability.

● Dual mode allows 2 voices to be played simulta-

neously.

● Split mode allows different voices to be played by

the left and right hands.

● Unique Clavinova Tone voice provides a fresh

sound for new musical expression.

● Metronome feature with variable tempo facilitates

practice.

● Digital recorder lets you record and play back

anything you play on the keyboard (up to approxi-

mately 4,200 notes).

● MIDI compatibility and a range of MIDI functions

make the Clavinova useful in a range of advanced

MIDI music systems.

● Built-in computer interface for direct connection to

personal computers running advanced music

software.

In order to make the most of your Clavinova’s

performance potential and features, we urge you

to read this Owner’s Manual thoroughly, and keep

it in a safe place for later reference.

■

F5: Metronome Functions ...........................27

F5.1: Beat ..................................................27

F5.2: Volume ..............................................27

■

F6: Left Pedal Mode .....................................27

■

F7: Piano Song Part Cancel Volume........... 27

■

F8: MIDI Functions....................................... 28

●

A Brief Introduction to MIDI ..................... 28

F8.1: MIDI Transmit Channel Selection...... 28

F8.2: MIDI Receive Channel Selection ......28

F8.3: Local Control ON/OFF ......................29

F8.4: Program Change ON/OFF................ 29

F8.5: Control Change ON/OFF ..................30

F8.6: MIDI Transmit Transpose................... 30

F8.7: Panel/Status Transmit ....................... 30

F8.8: Bulk Data Dump................................30

■

F9: Backup Functions .................................31

F9.1: Voice ................................................. 31

F9.2: MIDI .................................................. 31

F9.3: Tuning ...............................................31

F9.4: Pedal................................................. 31

Connecting to a Personal Computer .................. 32

●

Connecting to an Apple Macintosh Series

Computer.................................................32

●

Connecting to an IBM-PC/AT Series

Computer.................................................33

●

Connecting to an NEC PC-9801/9821

Series Computer .....................................33

Troubleshooting .....................................................34

Factory Preset Recall............................................. 34

Options & Expander Modules ............................... 34

MIDI Data Format.................................................... 35

MIDI Implementation Chart ...................................39

Keyboard Stand Assembly....................................40

Demo Song List......................................................48

Default Setting List ................................................ 48

Specifications.........................................................49

Tuning......................................................................17

●

Tuning Up ................................................17

●

Tuning Down............................................17

●

To Restore Standard Pitch ...................... 17

The Metronome & Tempo Control ...................... 18

■

The Metronome ............................................18

●

Metronome Volume ................................. 18

●

Other Metronome Functions ................... 18

■

Tempo Control.............................................. 18

Using the Recorder ...............................................19

■

Recording .....................................................19

●

Changing the Initial Settings ................... 20

●

Erasing a Single Track............................. 20

■

Playback .......................................................21

●

Synchro Start .......................................... 21

●

Left Pedal Start/Stop ...............................21

The Function Mode ............................................... 22

●

To Select a Function … ...........................22

■

F1: Tuning ..................................................... 23

■

F2: Scale ....................................................... 23

■

F3: Dual Mode Functions ............................ 24

F3.1: Dual Balance ....................................24

F3.2: Dual Detune......................................24

F3.3: 1st Voice Octave Shift .......................24

F3.4: 2nd Voice Octave Shift ...................... 24

F3.5: 1st Voice Effect Depth.......................25

F3.6: 2nd Voice Effect Depth......................25

F3.7: Slow-attack Strings ...........................25

F3.8: Reset ................................................25

■

F4: Split Mode Functions ............................ 25

F4.1: Split Point.......................................... 25

F4.2: Split Balance..................................... 26

F4.3: Right Voice Octave Shift ...................26

F4.4: Left Voice Octave Shift ...................... 26

F4.5: Right Voice Effect Depth ................... 26

F4.6: Left Voice Effect Depth...................... 26

F4.7: Damper Mode ................................... 26

F4.8: Reset ................................................26

Contents

1 [POWER] Switch

Press the [POWER] switch once to turn the power

ON, a second time to turn the power OFF. When the

power is initially turned ON, a voice selector LED

will light, and the power indicator located below the

left end of the keyboard will light.

2 [MASTER VOLUME] Control

The [MASTER VOLUME] control adjusts the

volume (level) of sound produced by the Clavinova’s

internal stereo sound system. The [MASTER VOL-

UME] control also adjusts headphone volume when a

pair of headphones is plugged into the PHONES jack

(page 7).

The Control Panel

3 [FUNCTION] Button

This button accesses a range of utility functions

— including the MIDI functions — that significantly

enhance versatility and playability. See page 22 for

details.

4 [TRANSPOSE] Button

The [TRANSPOSE] button allows access to the

Clavinova’s TRANSPOSE function (to shift the pitch

of the entire keyboard up or down in semitone

intervals).

5 [SPLIT] Button

Engages the split mode, in which different voices

can be played on the left- and right-hand sections of

the keyboard. See page 13 for details.

–

CLP-

555

STEREO SAMPLING

POWER

B0A0G0F0E0D0C0B-1A-1

C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6

278456

9@0 !

MASTER VOLUME

FUNCTION

TRANSPOSE SPLIT

VARIATION

PIANO 1

PIANO 2 CLAVI.TONE E.PIANO 1 E.PIANO 2 STRINGS

HARPSI-

CHORD

PIPE

ORGAN 1

PIPE

ORGAN 2

REVERB

ROOM

HALL 1

HALL 2

STAGE

HARD

MEDIUM

SOFT

FIXED

EFFECT TOUCH

MAX

MIN

METRONOME

TEMPO/

SONG

–

N O

Y ES

DEMO



PIANO SONG

PHONES Jacks

(Bottom Panel)

Tuning keys

(See page 17)

MASTER VOLUME

FUNCTION

TRANSPOSE SPLIT

VARIATION

PIANO 1

PIANO 2 CLAVI.TONE E.PIANO 1 E.PIANO 2 STRINGS

HARPSI-

CHORD

PIPE

ORGAN 1

PIPE

ORGAN 2

REVERB

ROOM

HALL 1

HALL 2

STAGE

HARD

MEDIUM

SOFT

FIXED

EFFECT TOUCH

MAX

MIN

METRONOME

TEMPO/

SONG

YES

START



STOP

REC

DEMO



PIANO SONG

RECORDER

The Control Panel

6 [REVERB] Button

The [REVERB] button selects a number of digital

reverb effects that you can use for extra depth and

expressive power. See page 14 for details.

7 [EFFECT] Button

This button engages a chorus effect which can

give your sound greater depth and animation.

8 [TOUCH] Button

The [TOUCH] button makes it easy to adjust the

touch response of the Clavinova to match your

playing style. See page 16 for details.

9 Voice Selectors & [VARIATION] Button

The CLP-555 has nine voice selectors and a

[VARIATION] button. Simply press any of the voice

selectors to select the corresponding voice. The voice

selector LED will light to indicate which voice is

currently selected. Press the [VARIATION] button

so that its indicator lights to select a variation of the

currently selected voice.

There is also a dual mode in which two voices can

be played simultaneously across the full range of the

keyboard (see page 12 for details), and a split mode

which allows different voices to be played by the left

and right hands (see page 13 for details).

0 [METRONOME] Button

Turns the metronome sound on and off. The

[TEMPO/SONG] buttons, below, are used to set the

tempo of the metronome sound, and the volume of

the metronome sound if used while the [METRO-

NOME] button is held — page 18.

! [TEMPO/SONG] (–/NO, +/YES) Buttons

These buttons adjust the tempo of the metronome

function as well as the playback tempo of the re-

corder function. The tempo range is from 32 to 280

beats per minute — page 18. These same buttons are

also used to select a piano song number for playback

— page 9. The [TEMPO/SONG] buttons are also

used to adjust a range of other parameters (i.e. their

“–/NO” and “+/YES” functions).

@ [DEMO/PIANO SONG] Button

Activates the demo playback mode in which you

can select playback of different demonstration

sequences for each of the Clavinova’s voices, and a

range of 30 piano songs. See page 9 for details.

# RECORDER [START/STOP] and [REC] But-

tons

These buttons control the Clavinova’s recorder,

letting you record and play back just about anything

you play on the keyboard — up to a maximum of

about 4,200 notes. See page 19 for details.

$ RECORDER [1] and [2] Buttons

The CLP-555 has a 2-track recorder, and these

buttons are used to select the track(s) to be recorded

or played back. See page 19 for details.

% Pedals

The soft (left), sostenuto (center) and damper

(right) pedals provide a range of expressive control

capabilities similar to the pedal functions on an

acoustic piano. See page 15 for details.

Soft pedal

Damper pedal

Sostenuto pedal

D6 E6 F6 G6 A6 B6 C7

$ #

START



STOP

REC

RECORDER

Preparation

If you will be using sheet music with your

Clavinova, raise the music stand built into its top

panel by lifting the rear edge of the music stand,

then flip down the music stand braces and engage

them with the corresponding recesses.

The music stand can be lowered after slightly

lifting it and folding the two brackets which sup-

port it against the back of the stand.

To open the CLP-555 key cover lift it just

enough to clear the keys (do not lift excessively)

then slide the cover back into the main unit. To

close the cover slide it forward all the way and then

lower it gently until it closes completely.

The Music Stand.............................................................................................................................................................................

The Key Cover...................................................................................................................................................................................

Opening and Closing the Lid...........................................................................................................................................

• Hold the cover with both hands when moving it, and

do not release it until it is fully opened or closed. Be

careful to avoid catching fingers (yours or others)

between the cover and main unit.

• Do not place objects on top of the key cover. Small

objects placed on the key cover may fall inside the

main unit when the cover is opened.

Z Raise the music stand as described in “The

Music Stand”, above.

X Raise and hold the right side of the lid (viewed

from the keyboard end of the instrument).

C Raise the lid stay and carefully lower the lid so

that the end of the stay fits into the recess in

the lid.

• Make sure that the end of the stay fits securely in

the lid recess. If the stay is not properly seated in

the recess the lid may fall causing damage or injury.

• Be careful that you or others do not bump the stay

while the lid is raised. The stay may be bumped out

of the lid recess causing the lid to fall.

• Be careful not to catch your fingers when raising or

lowering the lid.

Be careful of fingers when opening or closing.

Connections

1 AUX IN L/L+R and R Jacks

These jacks are intended for use with an external tone generator mod-

ule such as the Yamaha DOU-10 Disk Orchestra Unit. The stereo outputs

from the external tone generator module are connected to the AUX IN L/

L+R and R jacks, allowing the sound of the tone generator to be repro-

duced via the Clavinova’s internal sound system and speakers. A line-level

mono source can be connected to the L/L+R jack.

• The input signal from the AUX IN jacks is delivered to the AUX OUT jacks,

but is not affected by the Clavinova’s volume control or reverb effect.

2 AUX OUT L/L+R and R Jacks

The AUX OUT L/L+R and R jacks deliver the output of the Clavinova for

connection to an instrument amplifier, mixing console, PA system, or record-

ing equipment. If you will be connecting the Clavinova to a monaural sound

system, use only the L/L+R jack. When a plug is inserted into the L/L+R jack

only, the left- and right-channel signals are combined and delivered via the L/

L+R jack so you don’t lose any of the Clavinova’s sound.

• The AUX OUT jack signal must never be returned to the AUX IN jacks, either

directly or through external equipment.

3 MIDI IN, THRU and OUT Connectors

The MIDI IN connector receives MIDI data from an external MIDI

device (such as the DOU-10 Disk Orchestra Unit) which can be used to

control the Clavinova. The MIDI THRU connector re-transmits any data

received at the MIDI IN connector, allowing “chaining” of several MIDI

instruments or other devices. The MIDI OUT connector transmits MIDI

data generated by the Clavinova (e.g. note and velocity data produced by

playing the Clavinova keyboard).

More details on MIDI are given in “MIDI FUNCTIONS” on page 28.

4 TO HOST Connector & HOST SELECT Switch

This jack and selector switch allow direct connection to a personal

computer for sequencing and other music applications — without the need

for a separate MIDI interface. See page 32 for details.

● PHONES Jacks

(Bottom Panel)

Two pairs of standard pair of stereo headphones can be plugged in here

for private practice or late-night playing. The internal speaker system is

automatically shut off when a pair of headphones is plugged into either of

the PHONES jacks.

Tone Generator

AUX OUT

L+R

DOU-10

MIDI

IN OUT THRU

Personal Computer

HOST SELECT TO HOST

PC-2 PC-1

Mac

MIDI

Stereo System

DOU-10

AUX IN

L+R

Bottom Panel

MIDI

AUX IN

HOST SELECT TO HOST

IN OUT

L+R

THRU

PC-2 PC-1

Mac

MIDI

AUX OUT

L+R

Selecting & Playing Voices

Turn Power On...................................................................................................

After making sure that the Clavinova’s AC cord is properly plugged

into the Clavinova itself and plugged into a convenient AC wall outlet,

press the [POWER] switch located to the left of the keyboard to turn

the power ON.

When the power is turned ON, one of the voice selector LEDs will

light.

Set the Volume ..................................................................................................

Initially set the [MASTER VOLUME] control about half way

between the “MIN” and “MAX” settings. Then, when you start playing,

re-adjust the [MASTER VOLUME] control for the most comfortable

listening level.

Select a Voice .....................................................................................................

Select the desired voice by pressing one of the voice selectors. Use

the [VARIATION] button to select a variation of the current voice, as

required.

POWER

MASTER VOLUME

MAX

MIN

VARIATION

PIANO 1

PIANO 2 CLAVI.TONE E.PIANO 1 E.PIANO 2

STRINGS

HARPSI-

CHORD

PIPE

ORGAN 1

PIPE

ORGAN 2

Play................................................................................................................................

The Clavinova also offers keyboard touch response, so the volume

and timbre of notes played can be controlled according to how “hard”

you play the keys. The amount of variation available depends on the

selected voice.

Add Effects As Required.......................................................................

You can also change add reverb and/or a chorus effect as desired by

using the [REVERB] and [EFFECT] buttons (see page 14 for [RE-

VERB] button operation, and page 15 for [EFFECT] button opera-

tion).

REVERB

ROOM

HALL 1

HALL 2

STAGE

EFFECT

Demonstration tunes are provided that effectively demonstrate each of the

Clavinova’s voices. There are also 30 piano songs that you can play individually,

all in sequence, or in random order. Here’s how you can select and play the

demo tunes.

Playing the Demonstration Tunes

Engage the Demo Mode .........................................................................

Play a Voice Demo or Piano Song ...............................................

● Voice Demo Playback

Press one of the voice selectors to start playback of the corresponding voice

demo tune — featuring the voice normally selected by that voice selector

button. The indicator of the selected voice selector button will flash during

playback, and “---” (relative tempo) will appear on the LED display. You can

start playback of any other voice demo tune during playback by simply

pressing the corresponding voice selector. You can stop playback at any time

by pressing the [START/STOP] button, the voice selector of the currently

playing demo.

● Piano Song Playback

To play any of the 30 piano songs provided, use the [TEMPO/SONG] buttons to

select the number of the tune you want to play (the number will appear on the

LED display), then press the [START/STOP] button. Playback will stop automati-

cally when playback of the selected piano song has finished. To randomly select

and play one of the piano songs press the [VARIATION] button while playback is

stopped.

Select “ALL” instead of a number to play all piano songs and voice demo

tunes in sequence, or select “rnd” to continuously play all piano songs and

voice demo tunes in random order. The [VARIATION] button indicator will

flash during playback. Press the [START/STOP] button to stop playback. If a

voice selector is pressed while “ALL” is showing on the display, playback will

begin from the corresponding song.

• While a voice demo or piano song is playing, you can use the [TEMPO/

SONG] buttons to adjust the playback tempo as required. This produces a

relative tempo variation, with a range from “-99” through “---” to “99”.

• Use the [MASTER VOLUME] control to adjust the volume.

• The demo mode cannot be engaged while the recorder (page 19) is in

use.

• The default tempo is automatically selected whenever a new song is

selected, or playback of a new song begins during “

ALL

” or “

rnd

”

playback.

• No MIDI reception occurs in the demo mode.

• The demo/piano song data is not transmitted via the MIDI connectors.

* See page 48 for a complete listing of the demo tunes.

Press the [DEMO/PIANO SONG] button to engage the demo mode

— the voice selector indicators will flash in sequence.

VARIATION

PIANO 1

PIANO 2 CLAVI.TONE E.PIANO 1 E.PIANO 2

STRINGS

HARPSI-

CHORD

PIPE

ORGAN 1

PIPE

ORGAN 2

Exit From the Demo Mode....................................................................

After stopping demo playback, press the [DEMO/PIANO SONG]

button to exit from the demo mode and return to the normal play mode.

DEMO



PIANO SONG

DEMO



PIANO SONG

TEMPO/

SONG

–

YES

START



STOP

Piano Song A-B Repeat

The A-B Repeat function can be used to continuously repeat a

specified phrase within a piano song. Combined with the Part Cancel

function described below, this provides an excellent way to practice

difficult phrases.

Specify the Beginning (A) of the Phrase..............................

Select and play a piano song, then press the [FUNCTION] button at

the beginning of the phrase you want to repeat. This sets the “A” point

(“A-” will appear on the display).

To set the “A” point at the very beginning of the song, press the

[FUNCTION] button before starting playback.

Specify the End (B) of the Phrase ...............................................

Press the [FUNCTION] button a second time at the end of the

phrase. This sets the “B” point (“A-b” will appear on the display). At

this point repeat playback will begin between the specified A and B

points.

Stop Playback....................................................................................................

Press the [START/STOP] button to stop playback while retaining

the specified A and B points. A-B repeat playback will resume if the

[START/STOP] button is then pressed again.

To cancel the A and B points press the [FUNCTION] button once.

• The A and B points are automatically canceled when a new song is

selected.

• The A-B Repeat function cannot be used during “

ALL

” or “

rnd

” playback.

Playing the Demonstration Tunes

FUNCTION

START



STOP

REC

RECORDER

Piano Song Part Cancel

The 30 piano songs have separate left- and right-hand parts that can

be turned on and off as required so you can practice the corresponding

part on the keyboard. The right-hand part is played by the recorder’s [1]

track, and the left-hand part is played by recorder’s [2] track.

Turn the Desired Part Off.......................................................................

Press the RECORDER [1] or [2] button to turn the corresponding

part off — the corresponding indicator will go out (these buttons

alternately toggle the corresponding part on and off).

• The parts can be turned on or off even during playback.

• The Piano Song Part Cancel function cannot be used during “

ALL

” or

“

rnd

” playback.

• The “Piano Song Part Cancel Volume” function described on page 27 can

be used to set the canceled part so that it plays at a volume from “0” (no

sound) to “20”. The default setting is “5”.

• Both parts are automatically turned ON whenever a new song is selected.

Playing the Demonstration Tunes

START



STOP

REC

RECORDER

Start/Stop Playback.....................................................................................

Press the [START/STOP] button to start and stop playback as

required.

START



STOP

REC

RECORDER

Synchro Start .....................................................................................................

When the Synchro Start function is engaged, playback of the se-

lected piano song will begin automatically as soon as you start playing

on the keyboard.

To engage the Synchro Start function press the [START/STOP]

button while holding the part button corresponding to the part which is

ON. The rightmost dot on the display will light. Playback will then start

as soon as you begin playing on the keyboard.

• If you hold a track button which is OFF while pressing the [START/STOP]

button, that track will be turned ON and the Synchro Start mode will be

engaged.

START



STOP

REC

RECORDER

Left Pedal Start/Stop..................................................................................

The left pedal can be assigned to start and stop piano song playback

via the “Left Pedal Mode” function described on page 27.

The Dual Mode

The dual mode makes it possible to play two voices simultaneously across

the entire range of the keyboard.

To activate the dual mode simply press two voice selectors at the

same time (or press one voice selector while holding another). The

voice indicators of both selected voices will light when the dual mode is

active. To return to the normal single-voice play mode, press any single

voice selector.

• The dual and split modes cannot be engaged at the same time.

• The [VARIATION] button indicator will light if the variation is engaged for

either or both of the dual-mode voices. While the dual mode is engaged

the [VARIATION] button can be used to turn the variation for both voices

on or off. To use the variation for only one of the voices the setting must

be made prior to engaging the dual mode.

• The chorus effect will apply to both the dual mode voices as specified

after engaging the dual mode (the default effect on/off and depth settings

are different for each voice combination). The effect depth for the dual

mode voices can be individually set via the Dual Mode “1st Voice Effect

Depth” and “2nd Voice Effect Depth” functions described on page 25.

IANO 1 E.PIANO 2

HARPSI-

CHORD

Other Dual Mode Functions...............................................................

The CLP-555 Function mode provides access to a number of other

dual-mode functions, listed below. See the corresponding pages for

details.

• Dual Balance..........................................24

• Dual Detune ...........................................24

• 1st Voice Octave Shift............................. 24

• 2nd Voice Octave Shift ........................... 24

• 1st Voice Effect Depth ............................ 25

• 2nd Voice Effect Depth ...........................25

• Slow-attack Strings.................................25

• Reset......................................................25

The Split Mode

The split mode makes it possible to play two different voices on the keyboard

— one with the left hand and another with the right hand. The left-hand voice is

played on all keys to the left of (and including) a specified “split point” key, while

the right-hand voice is played on all keys to the right of the split point key.

To activate the split mode simply press the [SPLIT] button so thats

indicator lights. The split mode can be turned off at any time by press-

ing the [SPLIT] button again so that its indicator goes out.

• The dual and split modes cannot be engaged at the same time.

Selecting the Left-hand Voice...........................................................

The voice that was selected before the split mode was engaged

becomes the right-hand voice in the split mode. To select a left-hand

voice press the corresponding voice selector while holding the [SPLIT]

button. The indicator of the left-hand voice selector will light while it is

pressed, then only the right-hand voice selector and [SPLIT] button

indicators will remain lit.

• The variation can be individually turned on and off for the split mode

voices. Normally the voice indicator of the right-hand voice lights in the

split mode. The [VARIATION] can be used to turn the variation for the

right-hand voice on or off as required. While the [SPLIT] button is held,

however, the voice indicator of the left-hand voice lights, and in this state

the [VARIATION] button can be used to turn the variation for the left-hand

voice on or off as required.

• The chorus effect will apply to both the split mode voices as specified

after engaging the split mode (the default effect on/off and depth settings

are different for each voice combination). The effect depth for the split

mode voices can be individually set via the Split Mode “Left Voice Effect

Depth” and “Right Voice Effect Depth” functions described on page 26.

SPLIT

O 2

STRINGS

HARPSI-

CHORD

SPLIT

Setting the Split Point...............................................................................

The split point is initially set at the F#2 key by default. You can reset

the split point to any other key by pressing the key while holding the

[SPLIT] button (the name of the current split-point key appears on the

LED display while the [SPLIT] button is held). The split point can also

be set via the Function mode (see below).

Other Split Mode Functions...............................................................

The CLP-555 Function mode provides access to a number of other

split-mode functions, listed below. See the corresponding pages for

details.

• Split Point ...............................................25

• Split Balance ..........................................26

• Right Voice Octave Shift ......................... 26

• Left Voice Octave Shift ........................... 26

• Right Voice Effect Depth.........................26

• Left Voice Effect Depth ...........................26

• Damper Mode ........................................26

• Reset......................................................26

SPLIT

A-1 b=1 C 2 F~2

A-1 Bb-1 C2 F#2

Example:

Reverb

The [REVERB] button selects a number of digital reverb effects that you can

use for extra depth and expressive power.

To select a reverb type press the [REVERB] button a few times until

the indicator corresponding to the desired type lights (the indicators

light in sequence each time the [REVERB] button is pressed). No

reverb is produced when all indicators are off.

OFF

No reverb effect is selected when no REVERB indicator is lit.

ROOM

This setting add a continuous reverb effect to the sound that is similar

to the type of acoustic reverberation you would hear in a medium-size

room. This is the default reverb setting.

HALL 1

For a “bigger” reverb sound, use the HALL 1 setting. This effect

simulates the natural reverberation of a medium-size concert hall.

HALL 2

For a really spacious reverb sound, use the HALL 2 setting. This effect

simulates the natural reverberation of a large concert hall.

STAGE

A simulation of the type of reverb produced in a stage environment.

Adjusting Reverb Depth.........................................................................

The depth of the selected reverb effect can be adjusted for the

current voice by using the [–/NO] and [+/YES] buttons while holding

the [REVERB] button. The depth range is from 0 through 20 (the

current depth setting appears on the LED display while the [REVERB]

button is held). A setting of “0” produces no effect, while a setting of

“20” produces maximum reverb depth. Press the [–/NO] and [+/YES]

buttons simultaneously while holding the [REVERB] button to recall

the default setting: “10”.

• The reverb type and depth settings affect all voices.

REVERB

ROOM

HALL 1

HALL 2

STAGE

REVERB

ROOM

HALL 1

HALL 2

STAGE

TEMPO/

SONG

–

YES

The Chorus Effect

The [EFFECT] button engages a chorus effect that can give your sound

greater depth and animation.

The [EFFECT] button turns the chorus effect on (indicator lit) and

off (indicator off).

• The default effect on/off settings are different for each voice.

Adjusting Effect Depth.............................................................................

While the chorus effect is on the effect depth can be individually

adjusted for the selected voice by using the [–/NO] and [+/YES]

buttons while holding the [EFFECT] button. The depth range is from 0

through 20 (the current depth setting appears on the LED display while

the [EFFECT] button is held). A setting of “0” produces no effect,

while a setting of “20” produces maximum effect depth. Press the

[–/NO] and [+/YES] buttons simultaneously while holding the [EF-

FECT] button to recall the default setting for the current voice (the

default depth settings are different for each voice).

The Pedals

Soft (Left) Pedal...............................................................................................

The soft pedal reduces the volume and slightly changes the timbre of

notes played while the pedal is pressed. The soft pedal will not affect

notes which are already playing when it is pressed.

The left pedal can also be assigned to song start/stop operation via

the “Left Pedal Mode” described on page 27.

The CLP-555 has three foot pedals that produce a range of expressive ef-

fects similar to those produced by the pedals on an acoustic piano.

Damper (Right) Pedal ................................................................................

The damper pedal functions in the same way as a damper pedal on

an acoustic piano. When the damper pedal is pressed notes played have

a long sustain. Releasing the pedal immediately stops (damps) any

sustained notes.

TEMPO/

SONG

–

YES

EFFECT

Sostenuto (Center) Pedal......................................................................

If you play a note or chord on the keyboard and press the sostenuto

pedal while the note(s) are held, those notes will be sustained as long as

the pedal is held (as if the damper pedal had been pressed) but all

subsequently played notes will not be sustained. This makes it possible

to sustain a chord, for example, while other notes are played “staccato.”

Soft pedal

Damper pedal

Sostenuto pedal

Touch Sensitivity

Four different types of keyboard touch sensitivity — HARD, MEDIUM, SOFT

or FIXED — can be selected to match different playing styles and preferences.

To select a touch sensitivity type press the [TOUCH] button a few

times until the indicator corresponding to the desired type lights (the

indicators light in sequence each time the [TOUCH] button is pressed).

HARD

The HARD setting requires the keys to be played quite hard to

produce maximum loudness.

MEDIUM

The MEDIUM setting produces a fairly “standard” keyboard response.

This is the initial factory default setting.

SOFT

The SOFT setting allows maximum loudness to be produced with

relatively light key pressure.

FIXED

All notes are produced at the same volume no matter how hard the

keyboard is played. This is an ideal setting for voices which normally

have no keyboard sensitivity (i.e. harpsichord and organ).

The volume of notes played in the FIXED mode can be set by using

the [–/NO] and [+/YES] buttons while the [TOUCH] button is held (the

current volume level appears on the display). The volume range is

from 1 through 127. The default setting is 64.

Transposition

Use the [–/NO] or [+/YES] button while holding the [TRANS-

POSE] button to transpose down or up as required. The transposition

range is from “–12” (down one octave) through “0” (normal pitch) to

“12” (up one octave). The amount of transposition appears on the LED

display while the [TRANSPOSE] button is held. The default transpose

setting is “0”.

• The [TRANSPOSE] button indicator remains lit when a transpose setting

other than “0” is selected.

• Notes below and above the A-1 … C7 range of the Clavinova sound one

octave higher and lower, respectively.

The Clavinova’s TRANSPOSE function makes it possible to shift the pitch of

the entire keyboard up or down in semitone intervals up to a maximum of 12

semitones (i.e. a maximum of one octave up or down). “Transposing” the pitch of

the Clavinova keyboard facilitates playing in difficult key signatures, and you can

easily match the pitch of the keyboard to the range of a singer or other instru-

mentalist.

HARD

MEDIUM

SOFT

FIXED

TOUCH

TEMPO/

SONG

–

YES

TRANSPOSE

Tuning

Tuning makes it possible to adjust the pitch of the Clavinova over a 427.0 Hz

… 453.0 Hz (corresponding to the A3 note’s Hz) range in approximately 0.2

Hertz intervals. Pitch control is useful for tuning the Clavinova to match other

instruments or recorded music.

Tuning Up ...............................................................................................................

ZTo tune up (raise pitch), hold the A-1 and B-1 keys simultaneously.

XPress any key between C3 and B3. Each time a key in this range is

pressed the pitch is increased by approximately 0.2 Hz.

The [–/NO] and [+/YES] buttons can also be used to tune down or up,

respectively, in 1 Hz increments. Press the [–/NO] and [+/YES] buttons

simultaneously to recall standard tuning (A3 = 440 Hz).

CRelease the A-1 and B-1 keys.

Tuning Down.......................................................................................................

ZTo tune down (lower pitch), hold the A-1 and A#-1 keys simulta-

neously.

XPress any key between C3 and B3. Each time a key in this range is

pressed the pitch is decreased by approximately 0.2 Hz.

The [–/NO] and [+/YES] buttons can also be used to tune down or up,

respectively, in 1 Hz increments. Press the [–/NO] and [+/YES] buttons

simultaneously to recall standard tuning (A3 = 440 Hz).

CRelease the A-1 and A#-1 keys.

To Restore Standard Pitch...................................................................

ZTo restore the default pitch (A3 = 440 Hz), hold the A-1, A#-1 and

B-1 keys simultaneously.

XPress any key between C3 and B3.

CRelease the A-1, A#-1 and B-1 keys.

-1

TEMPO/

SONG

–

YES

-1

TEMPO/

SONG

–

YES

In terms of “Hertz”, the overall tuning range is from 427.0 Hz to 453.0

Hz. The current tuning setting is shown on the LED display while the tuning

is being adjusted. Tenths of a Hertz are indicated on the LED display by the

appearance and position of one or two dots, as in the following example:

• An alternative tuning method is available in the Function mode — page 23.

• The keyboard method of pitch control, described above, has no effect when

LOCAL OFF is active (see “MIDI FUNCTIONS,” page 28).

Display Value

440 440.0

4.40 440.2

44.0 440.4

440. 440.6

4.40. 440.8

The Metronome & Tempo Control

The CLP-555 built-in metronome is a convenient feature for practice, and it

can also provide a solid rhythmic guide when recording using the Recorder

feature, described below.

The Metronome

The metronome sound is alternately turned on and off by pressing

the [METRONOME] button. When on, the beat indicator flashes at the

current tempo.

Metronome Volume ......................................................................................

The volume of the metronome sound can be adjusted by using the

[–/NO] and [+/YES] buttons while holding the [METRONOME]

button. The volume range is from 1 through 20 (the current volume

setting appears on the LED display while the [METRONOME] button

is held). A setting of “1” produces minimum sound, while a setting of

“20” produces maximum metronome volume. Press the [–/NO] and [+/

YES] buttons simultaneously while holding the [METRONOME]

button to recall the default setting: “10”.

Other Metronome Functions .............................................................

The time signature (“beat”) of the metronome can be changed via

the metronome “Beat” function in the Function mode — page 27. The

Function mode also has an alternative method for adjusting the metro-

nome volume — page 27.

Tempo Control

The tempo of the metronome and recorder playback (the recorder is

described in the next section) can be set from 32 to 280 beats per

minute by using the [TEMPO/SONG t/s] buttons. The [t] button

decreases the tempo and the [s] button increases the tempo. The

selected tempo appears on the LED display in the normal play mode

and while the [TEMPO/SONG t/s] buttons are being used to adjust

the tempo. The default tempo (120 or the recorded song tempo when

the recorder contains data and the playback track lamp is lit) can be

recalled by simultaneously pressing the [t] and [s] buttons.

TEMPO/

SONG

–

YES

METRONOME

TEMPO/

SONG

–

YES

METRONOME

Beat indicator

Using the Recorder

The CLP-555 features a two-track recorder that let you record what you play

on the keyboard and then play it back. Two tracks mean that you can “overdub”

one part on top of another, using a different voice if you like. The recorder fea-

ture is a useful adjunct to any keyboard study program, since it lets you hear

exactly how you sound from the listener’s perspective. It can also be just plain

fun.

The recorder actually records the following data:

■ Entire Song

● Tempo ● Reverb type & depth ● Effect type

■ Individual Tracks

● Notes played ● Voice selection ● Voice variation

● Dual mode voices ● Split mode voices

● Damper pedal ● Soft pedal

● Sostenuto pedal (not recorded as an initial setting)

● Effect depth ● Dual mode functions (F3)

● Split mode functions (F4)

Recording

Make All Necessary Initial Settings ...........................................

Before actually beginning to record, select the voice you want to

record with (or voices if you will be using the dual or split mode). You

might also want to set the volume and tempo controls.

I.TONE E.PIANO 1 E.PIANO 2

HARPSI-

CHORD

Engage the Record Ready Mode ..................................................

Press the RECORDER [REC] button to engage the record ready

mode (recording does not actually start yet). The record ready mode can

be disengaged before recording by pressing the [REC] button a second

time.

• The record ready mode cannot be engaged while the demo/piano song

mode is engaged.

Select the Record Track..........................................................................

When the record mode is engaged in the previous step, the last-

recorded track will automatically be selected for recording and its

indicator — i.e. the [1] or [2] button indicator — will glow red. If you

want to record on a different track, press the appropriate track button so

that its indicator glows red.

• The track button indicators of tracks which contain previously recorded

data will glow green (unless the track is turned off as described below).

The previously-recorded data on the non-record track will normally be

played back as you record, so you can play along with a previously-

recorded track. If you don’t want to hear the previously recorded track as

you record, press the playback track button before pressing the [REC]

button (step 1, above) so that its indicator goes out.

• Recording on a track which already contains data will erase all previous

data on that track.

• When the record mode is engaged the amount of memory available for

recording will be shown on the LED display in approximate kilobytes

(starting at “21”), and the rightmost dot on the LED display will flash at the

current METRONOME tempo setting.

START



STOP

REC

RECORDER

START



STOP

REC

RECORDER

Using the Recorder

Start Recording................................................................................................

Recording will begin automatically as soon as you play a note on the

keyboard or press the [START/STOP] button. The current measure

number will appear on the display while recording.

• The left pedal can be assigned to start and stop recording via the “Left

Pedal Mode” function described on page 27.

• If the metronome was on when you started recording, you’ll be able to

keep time with the metronome while recording, but the metronome sound

will not be recorded.

• You can record up to a maximum of about 4,200 notes, depending on

pedal usage and other factors. The record track indicators will begin to

flash when recorder memory is almost full. If the memory becomes full

during recording, “FUL” will appear on the display and recording will stop

automatically.

START



STOP

REC

RECORDER

Stop Recording ................................................................................................

Press either the RECORDER [REC] or [START/STOP] button to

stop recording.

The indicator of the recorded track will glow green to indicate that it

now contains data.

Erasing a Single Track..............................................................................

All data can be erased from either of the recorder’s tracks by engag-

ing the record mode, selecting the track you want to erase, and then

pressing the [START/STOP] button twice without recording any data.

Changing the Initial Settings.............................................................

The initial voice (including dual mode), damper pedal, soft pedal,

tempo, reverb type, reverb depth, and effect settings made in step 1 of the

recording procedure are actually recorded by the CLP-555. These initial

settings can be changed after the recording is finished by pressing the

[REC] button to engage the record ready mode, pressing the appropriate

track button, making the required changes, and then pressing the [REC]

button again to exit from the record ready mode and register the changes.

If you do this, be careful not to press the [START/STOP] button or a key

on the keyboard, either of which will start recording and erase all previ-

ous recorded data on the selected track. It is possible to cancel the

operation even after changes have been made: change tracks and then

press the [REC] button to exit from the record mode (this also cancels

data for the entire song).

•

The initial data of the “Dual mode functions (F3)” or “Split mode functions

(F4)” cannot be changed.

START



STOP

REC

RECORDER

Press twice.

START



STOP

REC

RECORDER

START



STOP

REC

RECORDER

Using the Recorder

Playback

To play back what you’ve recorded, first make sure that the green track

indicators of the tracks you want to play are lit. If not, press the corresponding

track button(s) so that they are lit. Then press the RECORDER [START/

STOP] button. Playback starts from the beginning of the recorded data, and

will stop automatically at the end of the recorded data. You can also stop

playback at any time by pressing the [START/STOP] button. To mute a track

so that it doesn’t play back, press the corresponding track button so that its

indicator goes out (press again to turn the track back on).

The current measure number appears on the display during playback.

• It is possible to play along on the keyboard during playback.

• The playback volume and tempo can be adjusted by using the [MASTER VOLUME]

control and [TEMPO/SONG] buttons (press both [TEMPO/SONG] buttons simulta-

neously to recall the default tempo).

• All recorder data will be retained in memory for about one week after the power is

turned off. If you want to keep your recorded data for longer periods, turn the power

on for a few minutes at least once a week. It is also possible to store it to an

external MIDI storage device such as the Yamaha DOU-10 Disk Orchestra Unit by

using the Bulk Dump function described on page 30.

• The track indicators will not light automatically when the power is turned on even if

the recorder contains data. It is therefore necessary to press the track buttons so

that the corresponding green indicators light before starting RECORDER playback.

It is also a good idea to press the track buttons to check if the tracks contain data

before recording. If the green indicator lights when the corresponding track button

is pressed, that track contains data which will be erased and replaced by the newly-

recorded data.

• If the metronome is being used during playback, the metronome will stop when

playback is stopped.

• During recorder playback, the volume of a track which is turned off will always be

“0” (i.e. the “Piano Song Part Cancel Volume” function — page 27 — only affects

piano song playback.

• The playback data is not transmitted via the MIDI OUT connector.

• Playback cannot be started when the demo/piano song mode or function mode is

engaged. Playback can be started from the function mode, however, after one of

the track buttons — [1] or [2] — is pressed.

• Playback cannot be started when the recorder contains no data, or when both track

buttons are off.

START



STOP

REC

RECORDER

Synchro Start ....................................................................................................................

When the Synchro Start function is engaged, recorder playback will begin

automatically as soon as you start playing on the keyboard.

To engage the Synchro Start function press the [START/STOP] button

while holding a track button which is ON. The rightmost dot on the display will

flash at the current tempo. Playback will then start as soon as you begin playing

on the keyboard.

If you hold a track button which is OFF while pressing the [START/STOP]

button, that track will be turned ON and the Synchro Start mode will be engaged.

START



STOP

REC

RECORDER

Left Pedal Start/Stop.................................................................................................

The left pedal can be assigned to start and stop recorder playback via the

“Left Pedal Mode” function described on page 27.

The Function Mode

The [FUNCTION] button provides access to a range of functions that give the

CLP-555 extraordinary versatility. The functions are categorized in groups as

follows:

F1 Tuning ............................................................. 23

F2 Scale ............................................................... 23

F3 Dual Mode Functions .................................... 24

F4 Split Mode Functions .................................... 24

F5 Metronome Functions ................................... 27

F6 Left Pedal Mode ............................................. 27

F7 Piano Song Part Cancel Volume................... 27

F8 MIDI Functions ............................................... 28

F9 Backup Functions.......................................... 31

To Select a Function … ...........................................................................

ZPress the [FUNCTION] button so that its indicator lights.

• Functions cannot be selected during demo/piano song playback or when

the recorder is in operation.

TRANSPOSE SPLIT

XUse the [<] and [>] buttons (i.e. the [TRANSPOSE] and [SPLIT]

buttons) to select the desired function: F1 through F9.

CIn the case of the Dual Mode (F3), Split Mode (F4), Metronome

(F5), MIDI (F8), and Backup (F9) functions, you will have to press

the [+/YES] button once to enter the respective sub-mode after the

function has been selected, and then use the [<] and [>] buttons

again to select the desired sub-function.

• The Dual or Split mode must be engaged before the F3 and F4 functions

can be selected, respectively. If the corresponding mode is not engaged,

“

F3.-

” or “

F4.-

” will appear on the display and the corresponding sub-

mode will not be available.

• The Dual mode can be engaged while in the Function mode, but the

Function mode must be exited before the Split mode can be engaged.

VSet the function as required by using the [–/NO] and [+/YES]

buttons (see the individual function descriptions, below).

BPress the [FUNCTION] button so that its indicator goes out to exit

from the function mode.

FUNCTION

● Operation Example

(sub-mode)

Press [+/YES]

Use [<], [>]

Use [–/NO], [+/YES]

Press [–/NO] or [+/YES]

once

The Function Mode

Tuning

Scale

In addition to the tuning method described on page 17, overall tuning can also be accom-

plished via the F1 function.

After selecting “F1”, use the [–/NO] and [+/YES] buttons to lower or raise the pitch in 0.2

Hz increments (the first time the [–/NO] or [+/YES] button is pressed simply switches to the

tuning value display without actually changing the tuning). The overall tuning range is from

427.0 Hz to 453.0 Hz (corresponding to the A3 note’s Hz). Press the [–/NO] and [+/YES]

buttons simultaneously to recall the default value: 440 Hz.

Tenths of a Hertz are indicated on the LED display by the appearance and position of one

or two dots, as in the following example:

In addition to the standard Equal Temperament tuning, the CLP-555 includes 6 classic

tunings that you can select and use to play music of the corresponding period, or experiment

with in a more modern context. The tunings are:

1: Equal Temperament

2: Pure Major

3: Pure Minor

4: Pythagorean

5: Mean Tone

6: Werckmeister

7: Kirnberger

After selecting “F2”, use the [–/NO] and [+/YES] buttons to select the number of the

desired tuning, then press the key corresponding to the key on which you want the selected

tuning to be based (unlike the Equal Temperament tuning, the classic tunings must be tuned to

a specific key). The selected key will appear on the display, followed by a low bar if flat (e.g.

“2d_”) or a high bar if sharp (e.g. “2F~”).

Press the [–/NO] and [+/YES] buttons simultaneously to recall the default settings (Equal

Temperament tuning).

• No base key can be set for the 1: Equal Temperament tuning.

Display Value

440 440.0

4.40 440.2

44.0 440.4

440. 440.6

4.40. 440.8

The Function Mode

Dual Mode Functions

After selecting “F3.Y”, press the [+/YES] button to engage the dual-mode function sub-

mode, then use the [<] and [>] buttons to select the desired dual mode function, as listed

below.

If the Dual mode is not engaged “F3.-” will appear instead of “F3.Y” and the Dual mode

functions cannot be selected. If this happens engage the Dual mode and proceed.

■ SHORTCUT: You can jump directly to the dual-mode functions (F3) by pressing the

[FUNCTION] button while holding the two dual-mode voice selectors

corresponding to the voices you want to combine in the dual mode.

F3.1: Dual Balance.....................................................................................................................................

The volume levels of the two voices combined in the dual mode can be adjusted as re-

quired by using this function. Use the [–/NO] and [+/YES] buttons to adjust the balance as

required. The balance range is from 0 through 20. A setting of “10” produces equal balance

between the two dual-mode voices. Settings below “10” increase the volume of the 2nd voice

in relation to the 1st voice, and settings above “10” increase the volume of the 1st voice in

relation to the 2nd voice (“1st” and “2nd” refer to the left and right voice selectors, respec-

tively). Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting

(different for each voice combination).

F3.2: Dual Detune .......................................................................................................................................

This function makes it possible to detune the 1st and 2nd dual-mode voices to create a

thicker sound. Use the [–/NO] and [+/YES] buttons to set the amount of detuning as required.

The detune range is from –10 through 10. A setting of “0” sets both voices to the same pitch.

Settings below “0” increase the pitch of the 2nd voice in relation to the 1st voice, and settings

above “0” increase the pitch of the 1st voice in relation to the 2nd voice (“1st” and “2nd” refer

to the left and right voice selectors, respectively). Press the [–/NO] and [+/YES] buttons

simultaneously to recall the default setting (different for each voice combination).

F3.3: 1st Voice Octave Shift.............................................................................................................

F3.4: 2nd Voice Octave Shift...........................................................................................................

Depending on which voices you combine using the dual mode, the combination may sound

better if one of the voices is shifted up or down an octave. Use the [–/NO] and [+/YES]

buttons to set the octave of the 1st or 2nd voice as required (“1st” and “2nd” refer to the left

and right voice selectors, respectively). The available settings are “0” for normal pitch, “–1” to

shift the pitch down one octave, and “1” to shift the pitch up one octave. Press the [–/NO] and

[+/YES] buttons simultaneously to recall the default setting (different for each voice combina-

tion).

The Function Mode

F3.5: 1st Voice Effect Depth.............................................................................................................

F3.6: 2nd Voice Effect Depth...........................................................................................................

These functions make it possible to individually set the depth of the chorus effect for the

1st and 2nd dual-mode voices (“1st” and “2nd” refer to the left and right voice selectors,

respectively). Use the [–/NO] and [+/YES] buttons to set the effect depth for the correspond-

ing voice as required. The depth range is from 0 through 20. A setting of “0” produces no

effect, while a setting of “20” produces maximum effect depth. Press the [–/NO] and [+/YES]

buttons simultaneously to recall the default setting (the default effect depth setting is different

for each voice).

• The effect depth settings cannot be changed unless the EFFECT is ON. The Function mode must be

exited before EFFECT can be turned ON.

F3.7: Slow-attack Strings ...................................................................................................................

In a dual mode voice combination using a strings voice and any other voice, a better

“blend” can sometimes be produced by switching the strings voice to a slow-attack variation.

Use the [–/NO] and [+/YES] buttons to turn the slow-attack variation “On” or “OFF”, as

required. Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting:

“OFF”.

F3.8: Reset..........................................................................................................................................................

This function resets all dual-mode functions to their default values. Press the [+/YES]

button to reset the values. “End” will appear on the display when all functions have been

reset.

Split Mode Functions

After selecting “F4.Y”, press the [+/YES] button to engage the split-mode function sub-

mode, then use the [<] and [>] buttons to select the desired split mode function, as listed

below.

If the Split mode is not engaged “F4.-” will appear instead of “F4.Y” and the Split mode

functions cannot be selected. Also note that you must exit from the Function mode before the

Split mode can be engaged.

■ SHORTCUT: You can jump directly to the split-mode functions (F4) by pressing the

[FUNCTION] button while holding the [SPLIT] button.

F4.1: Split Point.............................................................................................................................................

In addition to the split point setting method described on page 13, the split point can be set

via this function. Use the [–/NO] and [+/YES] buttons to set the split point as required, or

simply press the appropriate key on the keyboard: from “A-1” to “C7”. Press the [–/NO] and

[+/YES] buttons simultaneously to recall the default setting: “F#2”.

The Function Mode

F4.2: Split Balance.....................................................................................................................................

The volume levels of the two voices combined in the split mode can be adjusted as re-

quired by using this function. Use the [–/NO] and [+/YES] buttons to adjust the balance as

required. The balance range is from 0 through 20. A setting of “10” produces equal balance

between the two split-mode voices. Settings below “10” increase the volume of the left-hand

voice in relation to the right-hand voice, and settings above “10” increase the volume of the

right-hand voice in relation to the left-hand voice. Press the [–/NO] and [+/YES] buttons

simultaneously to recall the default setting (different for each voice combination).

F4.3: Right Voice Octave Shift.......................................................................................................

F4.4: Left Voice Octave Shift...........................................................................................................

Depending on which voices you combine using the split mode, the combination may sound

better if one of the voices is shifted up or down an octave. Use the [–/NO] and [+/YES]

buttons to set the octave of the left-hand or right-hand voice as required. The available settings

are “0” for normal pitch, “–1” to shift the pitch down one octave, and “1” to shift the pitch up

one octave. Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting

(different for each voice combination).

F4.5: Right Voice Effect Depth ......................................................................................................

F4.6: Left Voice Effect Depth...........................................................................................................

These functions make it possible to individually set the depth of the chorus effect for the

left-hand and right-hand split-mode voices. Use the [–/NO] and [+/YES] buttons to set the

effect depth for the corresponding voice as required. The depth range is from 0 through 20. A

setting of “0” produces no effect, while a setting of “20” produces maximum effect depth.

Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting (the default

effect depth setting is different for each voice).

• The effect depth settings cannot be changed unless the EFFECT is ON. The Function mode must be

exited before EFFECT can be turned ON.

F4.7: Damper Mode...................................................................................................................................

The Damper Mode function determines whether the damper pedal affects the right voice,

the left voice, or both the left and right voices in the split mode. Use the [–/NO] and [+/YES]

buttons to select “2” for the left voice, “1” for the right voice, or “ALL” for both voices. Press

the [–/NO] and [+/YES] buttons simultaneously to recall the default setting: “ALL”.

F4.8: Reset..........................................................................................................................................................

This function resets all dual-mode functions to their default values. Press the [+/YES]

button to reset the values. “End” will appear on the display when all functions have been

reset.

The Function Mode

Metronome Functions

After selecting “F5.Y”, press the [+/YES] button to engage the metronome function sub-

mode, then use the [<] and [>] buttons to select the desired metronome function, as listed

below.

■ SHORTCUT: You can jump directly to the metronome functions by pressing the [FUNC-

TION] button while holding the [METRONOME] button.

F5.1: Beat.............................................................................................................................................................

Use this function to set the time signature of the metronome as required (i.e. the number of

unaccented beats that occur between each accented beat). Use the [–/NO] and [+/YES]

buttons to set the time signature to “0” (no accent), or a value between “2” and “6”, as re-

quired. Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting: “0”.

F5.2: Volume .....................................................................................................................................................

Use the [–/NO] and [+/YES] buttons to set the metronome volume as required. The vol-

ume range is from 1 through 20. A setting of “1” produces minimum sound, while a setting of

“20” produces maximum metronome volume. Press the [–/NO] and [+/YES] buttons simulta-

neously to recall the default setting: “10”.

Left Pedal Mode

This function sets the left pedal for normal soft-pedal operation, or for song start/stop

operation. Use the [–/NO] and [+/YES] buttons to select the desired left-pedal mode. “1” is

the normal soft-pedal mode, and “2” is the start/stop mode. When the start/stop mode is

selected, the left-pedal functions in the same way as the panel [START/STOP] button.

Piano Song Part Cancel Volume

This functions sets the volume at which a “canceled” part is played during piano song

playback (see page 11 for information on the “part-cancel” function). Use the [–/NO] and [+/

YES] buttons to set the volume as required. The volume range is from 0 through 20. A setting

of “0” produces no sound, while a setting of “20” produces maximum volume. Press the [–/

NO] and [+/YES] buttons simultaneously to recall the default setting: “5”.

The Function Mode

MIDI Functions

● A Brief Introduction to MIDI

MIDI, the Musical Instrument Digital Interface, is a world-

standard communication interface that allows MIDI-compatible

musical instruments and equipment to share musical information and

control one another. This makes it possible to create “systems” of

MIDI instruments and equipment that offer far greater versatility and

control than is available with isolated instruments. For example, most

MIDI keyboards (including the Clavinova, of course) transmit note

and velocity (touch response) information via the MIDI OUT connector whenever a note is played on the

keyboard. If the MIDI OUT connector is connected to the MIDI IN connector of a second keyboard (synthesizer,

etc.) or a tone generator (essentially a synthesizer with no keyboard), the second keyboard or tone generator will

respond precisely to notes played on the original transmitting keyboard. The result is that you can effectively

play two instruments at once, providing thick multi-instrument sounds.

This same type of musical information transfer is used for MIDI

sequence recording. A sequence recorder can be used to “record”

MIDI data received from a Clavinova, for example. When the

recorded data is played back, the Clavinova automatically “plays”

the recorded performance in precise detail.

The examples given above really only scratch the surface. MIDI

can do much, much more. The CLP-555 MIDI functions allow it to

be used in fairly sophisticated MIDI systems.

After selecting “F8.Y”, press the [+/YES] button to engage the MIDI function sub-mode, then

use the [<] and [>] buttons to select the desired MIDI function, as listed below.

• The rear-panel HOST SELECT switch must be set to “MIDI” in order to use the MIDI connectors.

• Always use a high-quality MIDI cable to connect MIDI OUT to MIDI IN terminals. Never use MIDI cables

longer than about 15 meters, since cables longer than this can pick up noise which can cause data errors.

F8.1: MIDI Transmit Channel Selection............................................................................................

F8.2: MIDI Receive Channel Selection .............................................................................................

The MIDI system allows transmission

and reception of MIDI data on 16 differ-

ent channels. Multiple channels have

been implemented to allow selective

control of certain instruments or devices

connected in series. For example, a single

MIDI sequence recorder could be used to

“play” two different instruments or tone

generators. One of the instruments or tone generators could be set to receive only on channel 1,

while the other is set to receive on channel 2. In this situation the first instrument or tone generator

will respond only to channel-1 information transmitted by the sequence recorder, while the second

instrument or tone generator will respond only to channel-2 information. This allows the sequence

recorder to “play” two completely different parts on the receiving instruments or tone generators.

Tone Generator

MIDI IN

MIDI IN MIDI THRU

DOU-10

MIDI OUT

Clavinova

(Set to receive on MIDI channel 1)

(Set to receive on MIDI

channel 2)

DOU-10

Clavinova

Data Being Recorded

Playback Data

MIDI IN

MIDI OUT

DOU-10

MIDI Cable

MIDI IN

MIDI OUT

Clavinova

The Function Mode

In any MIDI control setup, the MIDI channels of the transmitting and receiving equipment must

be matched for proper data transfer. A “Multi-timbre” receive mode is also available, which allows

simultaneous reception of different parts on all 16 MIDI channels, allowing the Clavinova to play

multi-channel song data received from a music computer or sequencer. There’s also a “1-2” mode

which allows simultaneous reception on channels 1 and 2.

Use the [–/NO] and [+/YES] buttons to select the desired transmit or receive channel. The trans-

mit channel parameter can also be turned “OFF” if you don’t want the Clavinova to transmit any

MIDI data. To select the multi-timbre receive mode, set the receive channel to “ALL”. Select “1-2”

for multi-timbre reception on channels 1 and 2 only.

Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting: transmit = “1”;

receive = “ALL”.

• In the dual mode the second voice data is transmitted on channel 2, and in the split mode the left-voice data

is transmitted on channel 2. In either mode, no data is transmitted if the transmit channel parameter is set to

“OFF”.

• Demo/piano song data and recorder playback data are not transmitted via MIDI.

• No MIDI reception occurs when the demo/piano song mode is engaged.

• Received MIDI data will not affect the Clavinova’s panel settings or what is being played on the keyboard —

except for reverb type, reverb depth, and effect on/off data which will affect the Clavinova settings.

F8.3: Local Control ON/OFF........................................................................................................................

“Local Control” refers to the fact that, normally, the

Clavinova keyboard controls its internal tone generator,

allowing the internal voices to be played directly from

the keyboard. This situation is “Local Control On”

since the internal tone generator is controlled locally by

its own keyboard.

Local control can be turned OFF, however, so that

the Clavinova keyboard does not play the internal

voices, but the appropriate MIDI information is still

transmitted via the MIDI OUT connector when notes are played on the keyboard. At the same time,

the internal tone generator responds to MIDI information received via the MIDI IN connector.

When using the DOU-10 Disk Orchestra Unit with the Clavinova, for example, Local Control

should be turned OFF when recording using the DOU-10 voices only, and ON when recording the

Clavinova voices while listening to playback of the DOU-10 voices.

Use the [–/NO] and [+/YES] buttons to turn local control “On” or “OFF”.

Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting: “On”.

F8.4: Program Change ON/OFF...............................................................................................................

Normally the Clavinova will respond to MIDI program change numbers received from an exter-

nal keyboard or other MIDI device, causing the correspondingly numbered voice to be selected on

the corresponding channel (the keyboard voice does not change). The Clavinova will normally also

send a MIDI program change number whenever one of its voices is selected, causing the correspond-

ingly numbered voice or program to be selected on the external MIDI device if the device is set up to

receive and respond to MIDI program change numbers.

This function makes it possible to cancel program change number reception and transmission so

that voices can be selected on the Clavinova without affecting the external MIDI device.

Use the [–/NO] and [+/YES] buttons to turn program change transmission and reception “On” or

“OFF”.

Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting: “On”.

DOU-10

OUT PUT

AUX IN

MIDI OUT

MIDI



Clavinova

The Function Mode

F8.5: Control Change ON/OFF......................................................................................................

Normally the Clavinova will respond to MIDI control change data received from an exter-

nal MIDI device or keyboard, causing the voice on the corresponding channel to be affected

by pedal and other “control” settings received from the controlling device (the keyboard voice

is not affected, but reverb depth data will affect the Clavinova settings). The Clavinova also

transmits MIDI control change information when one of its pedals or other appropriate con-

trols are operated.

This function makes it possible to cancel control change data reception and transmission so

that, for example, the Clavinova pedals and other controls can be operated without affecting an

external MIDI device.

Use the [–/NO] and [+/YES] buttons to turn control change transmission and reception

“On” or “OFF”.

Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting: “On”.

F8.6: MIDI Transmit Transpose......................................................................................................

This function allows the MIDI note data transmitted by the Clavinova to be transposed up

or down in semitone increments by up to plus or minus 12 semitones. The pitch of th-

Clavinova itself is not affected

Use the [–/NO] and [+/YES] buttons to set the desired amount of MIDI transmit transposi-

tion. The range is from “–12” (down one octave) through “0” (no transposition) to “12” (u

one octave)

Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting: “0”

F8.7: Panel/Status Transmit .............................................................................................................

This function causes all the current Clavinova control settings (selected voice, etc.) to be

transmitted via the MIDI OUT terminal. This is particularly useful if you will be recording

performances to a MIDI sequence recorder such as the Yamaha DOU-10 Disk Orchestra Unit

which will be used to control the Clavinova on playback. By transmitting the Clavinova panel

settings and recording them on the MIDI sequence recorder prior to the actual performance

data, the Clavinova will be automatically restored to the same settings when the performance

is played back.

Press the [+/YES] button to transmit the panel/status data. “End” will appear on the LED

display when the data has been successfully transmitted.

• See page 36 for list of the “Panel Data Contents” transmitted by this function.

• Panel setting data can only be transferred between the same models (data cannot, for example, be

transferred between a CLP-555 and CLP-411).

F8.8: Bulk Data Dump ............................................................................................................................

This function is used to transmit all data stored in the Recorder memory to a MIDI data

storage device such as the Yamaha DOU-10 Disk Orchestra Unit, other sequence recorders, or

MIDI compatible computers.

Press the [+/YES] button to begin bulk transmission. “End” will appear on the LED

display when the data has been successfully transmitted.

• Bulk dump will not function when the recorder is in operation.

• Recorder data can only be transferred between the same models (data cannot, for example, be

transferred between a CLP-555 and CLP-411).

• No MIDI note/panel data transmission or data reception occurs during a bulk dump transmit operation.

The Function Mode

Backup Functions

After selecting “F9.Y”, press the [+/YES] button to engage the backup function sub-mode,

then use the [<] and [>] buttons to select the desired backup function, as listed below.

• The backup settings themselves, and the contents of the recorder memory, are always backed up.

Even if backup is turned on via one of the functions described below, the data will only be

retained in memory for about 1 week if the power is not turned on during this time. If the

backup period is exceeded, all settings will be reset to their default values. If you want to

retain the backup settings for longer periods, be sure to turn the power switch on for a few

minutes at least once a week.

F9.2: MIDI.............................................................................................................................................................

Turns backup of the MIDI functions listed below on or off. Use the [–/NO] and [+/YES]

buttons to turn backup “On” or “OFF”.

The default backup mode is “OFF”.

• Channel (Transmit, Receive)

• Local ON/OFF

• Program Change ON/OFF

• Control Change ON/OFF

• MIDI Transmit Transpose

F9.3: Tuning.......................................................................................................................................................

Turns backup of the tuning functions listed below on or off. Use the [–/NO] and [+/YES]

buttons to turn backup “On” or “OFF”.

The default backup mode is “OFF”.

• Transpose

• Tuning

• Scale

F9.4: Pedal..........................................................................................................................................................

Turns backup of the left pedal function on or off. Use the [–/NO] and [+/YES] buttons to

turn backup “On” or “OFF”.

The default backup mode is “OFF”.

F9.1: Voice...........................................................................................................................................................

Turns backup of the voice functions listed below on or off. Use the [–/NO] and [+/YES]

buttons to turn backup “On” or “OFF”.

The default backup mode is “OFF”.

• Voice (Keyboard, Dual, Split)

• Dual (Voice, Dual Functions)

• Split (Voice, Split Functions)

• Reverb (Type, Depth)

• Effect (ON/OFF, Depth)

• Variation

• Touch Sensitivity

• Metronome (Beat, Volume)

• When using the [TO HOST] terminal of the CLP-555, first turn the power off on both the CLP-555 and the

computer before connecting the cable. After connecting the cable, turn the power of the computer on first,

then the CLP-555.

• When not using the [TO HOST] terminal of the CLP-555, make sure the cable is disconnected from the [TO

HOST] terminal. If the cable is left connected, the CLP-555 may not function properly.

• When the HOST SELECT switch is set to “Mac”, “PC-1”, or “PC-2, no data transfer occurs via the MIDI

connectors. To use the MIDI connectors for connection via a standard MIDI interface, set the HOST SELECT

switch to “MIDI”.

Connecting to a Personal Computer

Although the CLP-555 can be connected to a personal computer via the MIDI

IN/OUT connectors and a MIDI interface, the TO HOST connector and HOST

SELECT switch allow direct connection to Apple Macintosh or IBM-PC/AT per-

sonal computers for sequencing and other music applications without the need

for a separate MIDI interface.

Connect the TO HOST connector of the Clavinova to the modem or

printer port on your Macintosh, depending on which port your MIDI

software is using for MIDI data communication, using a standard

Macintosh 8-pin system peripheral cable. Set the HOST SELECT

switch to the “Mac” position.

You may also have to make other MIDI interface settings on the

computer side, depending on the type of software you use (refer to your

software owner’s manual). In any case the clock speed should be set to

1 MHz.

Connecting to an Apple Macintosh Series

Computer................................................................................................................

HOST SELECT TO HOST

PC-2 PC-1

Mac

MIDI

Apple Macintosh

Series Computer

Set to the “Mac”

position.

● “Mac” Cable Connections

2 (HSK i)1

1 (HSK 0)2

5 (RxD-)3

MINI DIN 

8-PIN

4 GND4

3 (TxD-)5

8 (RxD+)6

7 (GP i)7

6 (TxD+)8

MINI DIN 

8-PIN

• 8-pin system peripheral cable.

• Data transfer rate: 31,250 bps.

Connecting to an IBM-PC/AT Series Computer............

Connect the TO HOST connector of the Clavinova to the RS-232C port

on your IBM computer, using a standard 8-pin MINI DIN → 9-pin D-SUB

cross cable. Set the HOST SELECT switch to the “PC-2” position.

Refer to your software owner’s manual for information on any

settings you might have to make on the computer side.

Connecting to a Personal Computer

HOST SELECT TO HOST

PC-2 PC-1

Mac

MIDI

IBM-PC/AT

Series Computer

Set to the “PC-2”

position.

● “PC-2” Cable Connections

8 (CTS)1

7 (RST)2

2 (RxD)3

4 5 (GND)

3 (TxD) 5

MINI DIN 

8-PIN

D-SUB

9-PIN

• 8-pin mini DIN

→

9-pin D-SUB cable.

• Data transfer rate: 38,400 bps.

● Connector Pin Numbers

678

MINI DIN 8-PIN

D-SUB 9-PIN

■ Trademarks

• Apple and Macintosh are trademarks of Apple Computer, Inc.

• IBM-PC/AT is a trademark of International Business Machines Corporation.

• Windows is the registered trademark of Microsoft® Corporation.

All other trademarks are the property of their respective holders.

• If your system doesn’t work properly with the connections and settings listed above, your software may require

different settings. Check your software operation manual and if it requires a 31,250 bps. data transfer rate, set the

HOST SELECT switch to “PC-1”.

• When using the TO HOST terminal to connect to a personal computer using Windows, a Yamaha MIDI driver must

be installed in the personal computer. The Yamaha MIDI driver can be obtained at Yamaha’s home page on the

World Wide Web, <http://www.yamaha.co.jp/english/xg/>.

Factory Preset Recall

Options & Expander Modules

● Options

HPE-160 Stereo Headphones

High-performance lightweight dynamic head-

phones with extra-soft ear pads.

All dual mode, split mode, reverb, effect, touch sensitivity, tuning

settings, and the settings affected by the Backup Functions can be

restored to their original factory preset values by holding the C7 key

while turning the [POWER] switch ON. This also erases all recorder

data, and sets all Backup on/off settings (F9) to “OFF”.

POWER

Troubleshooting

If you encounter what appears to be a malfunction, please check the following points before assuming

that your Clavinova is faulty.

1. No Sound When the Power is Turned ON

Is the AC plug properly connected to the Clavinova

and an AC wall outlet? Check the AC connection

carefully. Is the MASTER VOLUME control turned

up to a reasonable listening level?

Also make sure that a pair of headphones is not

plugged into the PHONES jack, and that the Local

Control (page 29) is ON.

2. The Damper Pedal Doesn’t Work

If the damper pedal doesn’t work, or notes are

sustained even when the pedal is not pressed, make

sure that the pedal cord is properly plugged into the

main unit (page 46).

3. The Clavinova Reproduces Radio or TV Sound

This can occur if there is a high-power transmitter

in your vicinity. Contact your Yamaha dealer.

4. Intermittent Static Noise

This is usually due to turning ON or OFF a house-

hold appliance or other electronic equipment which is

fed by the same AC mains line as your Clavinova.

5. Interference Appears On Radio or TV Sets

Located Near the Clavinova

The Clavinova contains digital circuitry which can

generate radio-frequency noise. The solution is to

move the Clavinova further away from the affected

equipment, or vice versa.

6. Distorted Sound When the Clavinova is Con-

nected to An External Amplifier/Speaker

System

If the Clavinova is connected to a stereo system or

instrument amplifier and the sound is distorted, reduce

the setting of the Clavinova volume control to a level

at which the distortion ceases.

● If “Scn” appears on the display an internal malfunction has occurred. In this case, contact your Yamaha

dealer.

● Expander Modules

DOU-10 Disk Orchestra Unit

A range of MIDI recording and playback

functions, plus Yamaha Disk Orchestra Collection,

Disklavier PianoSoft™, General MIDI, and

Standard MIDI File disk playback capability.

2.1.(9) Effect4 Depth ( Variation Effect Send Level )

Cntrl# Parameter Data Range

94 Effect4 Depth 0...127

2.2 Mode Messages

The following Channel Mode messages are supported. (But the

actual mode is fixed to Poly and can not be changed.)

Cntrl# Parameter Data Range

120 All Sound Off 0

121 Reset All Controllers 0

123 All Notes Off 0

124 Omni Off 0

125 Omni On 0

126 Mono 0 ~ 16

127 Poly 0

2.2.(1) All Sound Off

Switches off all sound from the channel. Does not reset Note On

and Hold On conditions established by Channel Messages.

2.2.(2) Reset All Controllers

Resets controllers as follows.

Controller Value

Expression 127 (max)

Damper Pedal 0 (off)

Sostenuto 0 (off)

Soft Pedal 0 (off)

2.2.(3) All Notes Off

Switches off all of the channel’s “on” notes. Any notes being held

by DAMPER or SOSTENUTO continue to sound until DAMPER/

SOSTENUTO goes off.

2.2.(4) Omni Off (reception only)

Same processing as for All Notes Off.

2.2.(5) Omni On (reception only)

Same processing as for All Notes Off.

2.2.(6) Mono (reception only)

Same processing as for All Sound Off.

2.2.(7) Poly (reception only)

Same processing as for All Sound Off.

* When control change reception is turned OFF in the Function

mode, no control change data is transmitted or received.

* Local on/off, OMNI on/off are not transmitted. (The appropriate

note off number is supplied with “All Note Off” transmission).

* When a voice bank MSB/LSB is received, the number is stored

in the internal buffer regardless of the received order, then the

stored value is used to select the appropriate voice when a

program change message is received.

* The Multi-timbre and Poly modes are always active. No change

occurs when OMNI ON, OMNI OFF, MONO, or POLY mode

messages are received.

Si vous êtes très familier avec l’interface MIDI ou si vous

utilisez un ordinateur pour commander votre matériel de

musique au moyen de messages MIDI générés par

ordinateur, les données suivantes vous seront utiles et vous

aideront à commander le Clavinova.

SI usted está ya familiarizado con MIDI, o si emplea una

computadora para controlar sus aparatos musicales con

mensajes MIDI generados por computadora, los datos

proporcionados en esta sección le ayudarán a controlar la

Clavinova.

If you’re already very familiar with MIDI, or are using a

computer to control your music hardware with computer-

generated MIDI messages, the data provided in this section

can help you to control the Clavinova.

Falls Sie bereits mit MIDI vertraut sind oder einen Compu-

ter zur Erzeugung von MIDI-Steuermeldungen für die

Instrumente verwenden, können Sie sich zur Steuerung des

Clavinovas nach den im folgenden Abschnitt aufgeführten

Spezifikationen richten.

1. NOTE ON/OFF

Data format: [9nH] -> [kk] -> [vv]

9nH = Note ON/OFF event (n = channel number)

kk = Note number (Transmit: 09H ~ 78H = A-2 ~ C8 /

Receive: 00H ~ 7FH = C-2 ~ G8)

vv = Velocity (Key ON = 1 ~ 127. Key OFF = 0)

Data format: [8nH] -> [kk] -> [vv]

8nH = Note OFF event (n = channel number)

kk = Note number: 00H ~ 7FH = C-2 ~ G8

vv = Velocity (Key OFF = 0 ~ 127)

* 8nH (note off) is receive only.

9nH (vvH=00H) used for transmission.

2. CONTROL CHANGE & MODE MESSAGES

Data format: [BnH] -> [cc] -> [vv]

BnH = Control event (n = channel number)

cc = Control number

vv = Data Range

2.1 Control Change

2.1.(1) Bank Select

Cntrl# Parameter Data Range

0 Bank Select MSB 0:Normal

32 Bank Select LSB 0...127

112 Variation Off

113 Variation On

A new bank selection does not become effective until receipt of the

next Program Change message.

2.1.(2) Main Volume (reception only)

Cntrl# Parameter Data Range

7 Volume MSB 0...127

2.1.(3) Expression

Cntrl# Parameter Data Range

11 Expression MSB 0...127

2.1.(4) Damper

Cntrl# Parameter Data Range

64 Damper MSB 0...127

Half pedal continuous data is received and accepted.

2.1.(5) Sostenuto

Cntrl# Parameter Data Range

66 Sostenuto 0...127

(0-63:off, 64-127:on)

2.1.(6) Soft Pedal

Cntrl# Parameter Data Range

67 Soft Pedal 0...127

(0-63:off, 64-127:on)

2.1.(7) Attack Time

Cntrl# Parameter Data Range

73 Attack Time 0...127

2.1.(8) Effect1 Depth ( Reverb Send Level )

Cntrl# Parameter Data Range

91 Effect1 Depth 0...127

Adjusts the reverb send level.

MIDI Data Format/MIDI-Datenformat/Format des données MIDI/

Formato de datos MIDI

MIDI Data Format/MIDI-Datenformat/Format des données MIDI/Formato de datos MIDI

3. PROGRAM CHANGE

Data format: [CnH] -> [pp]

CnH = program event (n = channel number)

pp = Program number

pp VOICE NAME

00 PIANO 1

01 PIANO 2

88 CLAVINOVA TONE

05 E. PIANO 1

04 E. PIANO 2

06 HARPSICHORD

48 STRINGS

19 PIPE ORGAN 1

16 PIPE ORGAN 2

4. SYSTEM REALTIME MESSAGES

[rrH]

F8H: Timing clock

FAH: Start

FCH: Stop

FEH: Active sensing

Data Transmission Reception

F8H Transmitted every Received as 96-clock tempo timing

96 clocks when MIDI clock is set to External

FAH Recorder start Recorder start

FCH Recorder stop Recorder stop

FEH Transmitted every All notes are turned off if no data is

200 milliseconds received for more than 400

milliseconds

* Caution: If an error occurs during MIDI reception, the Damper, Sostenuto,

and Soft effects for all channels are turned off and an All Note Off occurs.

5. SYSTEM EXCLUSIVE MESSAGES

(1) Panel Data Transmit

Data format: [F0H] -> [43H] -> [0nH] -> [7CH] -> ... ->

[F7H]

F0H, 43H, 0nH, 7CH (n: channel number)

00H, 2EH (

data length

)

43H, 4CH, 20H, 20H (CL)

43H, 4CH, 50H, 27H, 39H, 36H (CLP ’96)

30H, 30H (version x, y)

[PANEL DATA]

[CHECK SUM (1byte)] = 0-(43H+4CH+20H+......+Data end)

F7H

• Panel Data Contents

(1) Voice

(2) Dual On/Off

(3) Dual Voice

(4) Dual Balance

(5) Dual Detune

(6) Dual Voice1 Octave

(7) Dual Voice2 Octave

(8) Dual Voice1 Effect Depth

(9) Dual Voice2 Effect Depth

(10) Dual Slow-attack Strings On/Off

(11) Split On/Off

(12) Split Voice

(13) Split Point

(14) Split Balance

(15) Split Voice1 Octave

(16) Split Voice2 Octave

(17) Split Voice1 Effect Depth

(18) Split Voice2 Effect Depth

(19) Split Damper Mode

(20) Reverb Type 1

(21) Reverb Depth 1

(22) Effect Type 1

(23) Effect Type 2

(24) Effect Depth

(25) - - -

(26) Variation 1 On/Off

(27) Variation 2 On/Off

(28) Touch Sensitivity

(29) Touch Volume in the FIXED Mode

(30) Left Pedal (Soft/Start)

(31) - - -

(32) Absolute tempo low byte

(33) Absolute tempo high byte

(34) - - -

(2) Universal Realtime Message

Master Volume

Data format: [F0H] -> [7FH] -> [XnH] -> [04H] -> [01H] ->

[ll] -> [mm] -> [F7H]

F0 = Exclusive status

7F = Universal Realtime

7F = ID of target device

04 = Sub-ID #1=Device Control Message

01 = Sub-ID #2=Master Volume

ll = Volume LSB

mm = Volume MSB

F7 = End of Exclusive

F0 = Exclusive status

7F = Universal Realtime

XN = When N is received N=0~F, whichever is received.

x = don’t care

04 = Sub-ID #1=Device Control Message

01 = Sub-ID #2=Master Volume

ll = Volume LSB

mm = Volume MSB

F7 = End of Exclusive

(3) Universal Non-Realtime Message

General MIDI Mode On

Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->

[F7H]

F0 = Exclusive status

7E = Universal Non-Realtime

7F = ID of target device

09 = Sub-ID #1=General MIDI Message

01 = Sub-ID #2=General MIDI On

F7 = End of Exclusive

F0 = Exclusive status

7E = Universal Non-Realtime

XN = When N is received N=0~F, whichever is received.

X = don’t care

09 = Sub-ID #1=General MIDI Message

01 = Sub-ID #2=General MIDI On

F7 = End of Exclusive

When the General MIDI mode ON message is received, the MIDI

system will be reset to its default settings.

This message requires approximately 50ms to execute, so suffi-

cient time should be allowed before the next message is sent.

(4) XG Native Parameter Change

Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hh] ->

[mm] -> [ll] -> [dd] -> [F7H]

F0 = Exclusive status

43 = YAMAHA ID

1n = When n is received n=0~F, whichever is received.

When n is transmitted n always=0.

4C = Model ID of XG

hh = Address High

mm = Address Mid

ll = Address Low

dd = Data

F7 = End of Exclusive

Data size must match parameter size (2 or 4 bytes).

When the XG System On message is received, the MIDI system

will be reset to its default settings.

The message requires approximately 50ms to execute, so suffi-

cient time should be allowed before the next message is sent.

* When program change reception is turned OFF in the Function

mode, no program change data is transmitted or received.

(5) XG Native Bulk Data (reception only)

Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aa] ->

[bb] -> [hh] -> [mm] -> [ll] -> [dd] ->...-> [cc]

-> [F7H]

F0 Exclusive status

43 YAMAHA ID

0n When n is received n=0~F, whichever is received.

When n is transmitted n always=0.

4C Model ID of XG

aa ByteCount

bb ByteCount

hh Address High

mm Address Mid

ll Address Low

dd Data

| |

cc Check sum

F7 End of Exclusive

For information about “Address” and “Byte Count” fields, refer to

attached tables.

In the attached tables “TOTAL SIZE” partitions a data series into

single bulk dumps. The “address” is the first byte of the bulk data.

The checksum value is set such that the sum of Byte Count, Ad-

dress, Data, and Checksum has value zero in its seven least

significant bits.

If too much bulk data is received at a time there is a chance of

error. The total data for a bulk dump should not exceed 512 bytes,

it is recommended that data be kept under 512 bytes with an

interval time of 120msec or more between 512 byte bulk.

(6) Clavinova MIDI Format

Data format: [F0H] -> [43H] -> [73H] -> [3BH] -> [yy] ->

[F7H]

F0 = Exclusive status

43H = Yamaha ID

73H = Clavinova ID

3BH = CLP-555 ID

yy = Substatus

yy Information

02H Internal MIDI clock

03H External MIDI clock

06H Bulk Data

* The bulk data follows 06H.

* When yy=2, 3 or Clavinova common ID (01H) is recog-

nized

as well as 3BH.

BULK DUMP FORMAT

F0H, 43H, 73H

nnH (Product ID: CLP-555=4F)

06H (Bulk ID)

05H (Sequence data, Bulk Dump Format)

0xH, 0xH, 0xH, 0xH (Data length= xxxx bytes)

[BULK DATA] (low, high........low, high)

[CHECK SUM (1byte)] = 0-sum (BULK DATA)

F7H

(7) Special Control

Data format: [F0H] -> [43H] -> [73H] -> [3BH] -> [11H] ->

[0nH] -> [cc] -> [vv] -> [F7H]

43H = Yamaha ID

73H = Clavinova ID

3BH = CLP-555 ID

11H = Clavinova special control

0nH = Control MIDI change + channel number

cc = Control number

vv = Value

Control 0nH ccH dd

Split Point Always 00 14H 14H : Split Key Number

Metronome Always 00 1BH 00H : off

01H : –

02H : 2/4

03H : 3/4

04H : 4/4

05H : 5/4

06H : 6/4

07H : No accent

Channel Detune ch: 00-0F 43H 00H-7FH

Voice Reserve ch: 00-0F 45H 00H : Reserve off

7FH : on *1

*1 When Volume, Expression is received for Reserve On, they will

be effective from the next Key On. Reserve Off is normal.

(8) Others

Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] ->

[00H] -> [00H] -> [mmH] -> [llH] -> [ccH] ->

[F7H]

Master Tuning (XG and last message priority) simultaneously

changes the pitch of all channels.

F0H = Exclusive Status

43H = Yamaha ID

1nH = Transmission from n=CLP is always 0. 0-F is received.

27H = Model ID of TG100

30H = Sub ID

00H =

mmH = Master Tune MSB

llH = Master Tune LSB

ccH = don’t care (under 7FH)

F7H = End of Exclusive

REVERB TYPE

TYPE MSB TYPE LSB

DEC HEX 00 01 02 03~

000 0 Effect Off <—— <—— <——

001 1 Hall1 Hall2 Hall1 <——

002 2 Room1 <—— <—— <——

003 3 Stage1 <—— <—— <——

004 4 No Effect <—— <—— <——

: : :

<—— .......... Same as Basic Effect (LSB=0)

● Effect MIDI Map

VARIATION TYPE

TYPE MSB TYPE LSB

DEC HEX 00 01 02 03~

000 0 Effect Off <—— <—— <——

: : No Effect <—— <—— <——

065 41 Chorus1 <—— <—— <——

: : No Effect <—— <—— <——

<—— .......... Same as Basic Effect (LSB=0)

MIDI Parameter Change table ( SYSTEM )

Address (H) Size (H) Data (H) Parameter Description Default value (H)

00 00 00 4

020C - 05F4(*1)

MASTER TUNE -50 - +50[cent] 00 04 00 00

01 1st bit 3 - 0 → bit 15 - 12 400

02 2nd bit 3 - 0 → bit 11 - 8

03 3rd bit 3 - 0 → bit 7 - 4

4th bit 3 - 0 → bit 3 - 0

04 1 00 - 7F MASTER VOLUME 0 - 127 7F

05 1 — —

06 1 34 - 4C(*2) TRANSPOSE -12 - +12[semitones] 40

7E 00 XG SYSTEM ON 00=XG sytem ON

7F 00 RESET ALL PARAMETERS 00=ON (receive only)

TOTAL SIZE 07

*1: Values lower than 020CH select -50 cents. Values higher than 05F4H select +50 cents.

*2: Values from 28 through 33 are interpreted as -12 through -1. Values from 4D through 58 are interpreted as +1 through +12.

MIDI Parameter Change table ( EFFECT 1)

Refer to the “Effect MIDI Map” for a complete list of Reverb, Chorus and Variation type numbers.

Address (H) Size (H) Data (H) Parameter Description Default value (H)

02 01 00 2 00-7F REVERB TYPE MSB Refer to Effect MIDI Map 01(=HALL1)

00-7F REVERB TYPE LSB 00 : basic type 00

0C 1 00-7F REVERB RETURN -∞dB...0dB...+6dB(0...64...127) 40

TOTAL SIZE 0E

02 01 40 2 00-7F VARIATION TYPE MSB Refer to Effect MIDI Map 00(=Effect off)

00-7F VARIATION TYPE LSB 00 : basic type 00

TOTAL SIZE 21

* “VARIATION” refers to the EFFECT on the panel.

MIDI Parameter Change table ( MULTI PART )

Address (H) Size (H) Data (H) Parameter Description Default value (H)

08 nn 11 1 00 - 7F DRY LEVEL 0 - 127 7F

nn = PartNumber

MIDI Data Format/MIDI-Datenformat/Format des données MIDI/Formato de datos MIDI

YAMAHA [Clavinova] Date: 11/20, 1996

Model: CLP-555 MIDI Implementation Chart Version: 1.0

Function Transmitted Recognized Remarks

Basic Default 1 1

Channel Changed 1~16 1~16

Default 3 1 *1 Poly Mode only

Mode Messages XX

***************** X

Note 9~120 0~127

Number : True voice ***************** 21~108

Velocity Note on O 9nH, v=1~127 O v=1~127

Note off X 9nH, v=0 X

After key’s XX

Touch Ch’s XX

Pitch Bender XX

Control Change

0, 32 OOBank Select

07 XOVolume

11 XOExpression

64 OODamper

66 OOSostenuto

67 OOSoft pedal

91 OOReverb Depth

94 OOEffect Depth

120 XOAll sounds off

121 XOReset All Controllers

Program OO

Change : True # *****************

System Exclusive OO

System : Song Position XX

: Song Select XX

Common : Tune XX

System : Clock OO

Real Time: Commands OO

Aux : Local ON/OFF XX

: All Notes Off OO (123~127)

Messages: Active Sense OO

: Reset XX

Notes : *1 = Recieve Mode is always multi timbre and Poly mode.

Mode 1: OMNI ON, POLY Mode 2: OMNI ON, MONO O: Yes

Mode 3: OMNI OFF, POLY Mode 4: OMNI OFF, MONO X: No

• Be careful not to confuse parts, and be sure to install

all parts in the correct direction. Please assemble in

accordance with the sequence given below.

• Assembly should be carried out by at least two

persons.

• Be sure to use the correct screw size, as indicated

above. Use of incorrect screws can cause damage.

• Be sure to tighten up all screws upon completing

assembly of each unit.

• The entire package must be turned over during

assembly, so select an area that is large enough for

the unpacking and assembly operation.

Open the carton and remove the parts from

the upper level.

Referring to the illustration, make sure that you have all the

required parts.

Zusammenbau und AufstellungKeyboard Stand Assembly

● Cord holders

● Kabelhalter

● Serre-câble

● Soportes de cable

● AC power cord

● Netzkabel

● Cordon d’alimentation

● Cable de alimentación de CA

• A bench may be supplied or optional, depending on

the location in which the instrument was purchased.

Attach the three legs (A, B, C).

Use scissors or a cutter to remove the packing material in

which the main unit is wrapped. Then attach the legs to the

bottom of the main unit using four 5 x 20 mm long screws per

leg. Please refer to the illustration carefully when attaching the

legs, to ensure that the positions of the (A) and (B) legs are not

reversed. Also make sure that there is minimum space between

the (A) and (B) leg flanges and the metal frame on the bottom of

the main unit (the screws which attach the legs to this frame will

be installed later, in step

● Front leg A

● Vorderes Standbein A

● Pied avant A

● Pata frontal A

● Front leg B

● Vorderes Standbein B

● Pied avant B

● Pata frontal B

● Rear leg C

● Hinteres Standbein C

● Pied arrière C

● Pata trasera C

● Pedal box D

● Pedalkasten D

● Pédalier D

● Caja de pedales D

x 20

5 x 20 mm long screws

Lange Schrauben

(5 x 20 mm)

Vis longue 5 x 20 mm

Tornillos largos de 5 x 20 mm

x 2

• Achten Sie darauf, die Teile nicht zu verwechseln, und

installieren Sie alle Teile in der richtigen Ausrichtung.

Gehen Sie beim Zusammenbau bitte in der angegebe-

nen Reihenfolge vor.

• Die Montage sollte von mindestens zwei Personen

vorgenommen werden.

• Achten Sie darauf, die richtige Schraubengröße zu

verwenden, wie es oben gezeigt ist. Die Verwendung

der falschen Schrauben kann zu Schäden führen.

• Achten Sie während der Montage darauf, bei jedem

Arbeitsgang alle Schrauben festzuziehen.

• Das Instrument wird im Karton zusammengebaut und

muß abschließend zum Aufstellen umgedreht werden.

Achten Sie darauf, daß ausreichend Platz zum Aus-

packen und Aufstellen vorhanden ist.

Den Karton öffnen und die Teile der ober-

sten Lage herausnehmen.

Prüfen Sie anhand der Abbildung, ob die Teile vollzählig

vorhanden sind.

• Je nach Vertriebsland wird eine Sitzbank entweder

standardmäßig mitgeliefert oder ist als Sonderzubehör

erhältlich.

Die drei Standbeine (A, B und C) montieren.

Entfernen Sie das Verpackungsmaterial an der Unterseite des

Instruments mit einer Schere oder einem anderen

Schneidwerkzeug. Schrauben Sie dann die drei Standbeine mit

jeweils vier langen Schrauben (5 x 20 mm) an das Instrument.

Richten Sie sich bei der Montage der Standbeine bitte nach der

Abbildung — die vorderen Standbeine (A und B) dürfen nicht

vertauscht werden. Achten Sie auch darauf, daß zwischen den

Ansätzen an den vorderen Standbeinen (A und B) und dem

Metallrahmen an der Unterseite des Instruments ein möglichst

kleiner Zwischenraum verbleibt (die Standbeine werden an späte-

rer Stelle, in Schritt

, mit diesem Rahmen verschraubt ).

Assemblage du support de clavier Conjunto del soporte del teclado

5 x 20 mm long screws

Lange Schrauben (5 x 20 mm)

Vis longue 5 x 20 mm

Tornillos largos de 5 x 20 mm

Minimum space between the leg flanges and

the metal frame.

Minimaler Zwischenraum zwischen Ansatz

und Metallrahmen.

Espace minimum entre les collerettes de

pieds et le châssis métallique.

Espacio mínimo entre las bridas de las

patas y el bastidor metálico.

• Veiller à ne pas mélanger les pièces et à les installer

dans le sens correct. Veuillez assembler l’instrument

dans l’ordre indiqué ci-dessous.

• La présence de deux personnes minimum est néces-

saire pour procéder au montage.

• Toujours utiliser des vis aux dimensions correctes,

comme indiqué cidessus. I’utilisation de vis aux dimen-

sions incorrectes pourrait en effet endommager l’instru-

ment.

• Resserrer convenablement toutes les vis après le

montage de chaque élément.

• L’ensemble du carton d’emballage doit être retourné

pendant le montage aussi, choisir un endroit suffisam-

ment spacieux pour les opérations de déballage et de

montage.

Ouvrir le carton et retirer les pièces du ni-

veau supérieur.

Vérifier que toutes les pièces figurant sur l’illustration se

trouvent bien dans le carton.

Monter les trois pieds (A, B, C).

Utiliser une paire de ciseaux ou un cutter pour retirer les ma-

tériaux dans lesquels l’instrument est emballé. Puis, monter les

pieds au-dessous de l’instrument avec quatre vis longues 5 x 20

mm par pied. Pour le montage des pieds,se référer soigneusement

à l’illustration afin de garantir que la position des pieds (A) et

(B) n’est pas inversée. S’assurer aussi qu’il y a un espace mini-

mum entre les collerettes de pieds (A) et (B) et le châssis

metallique sous l’instrument (les vis qui fixent les pieds sur ce

châssis seront installées ultérieurement, à l’étape

• Un banc peut être fourni ou en option, selon l’endroit

où l’instrument a été acheté.

• Observe cuidado para no confundir las piezas, y ase-

gúrese de montar todas ellas en el sentido correcto.

Proceda al montaje en el orden indicado a continua-

ción.

• El montaje deberá realizarse al menos por dos perso-

nas.

• Procure utilizar los tornillos del tamaño adecuado,

según se indica arriba. El empleo de tornillos inade-

cuados puede ocasionar daños en el instrumento.

• Asegúrese de apretar bien todos los tornillos después

de montar cada unidad.

• Deberá dar la vuelta a todo el paquete durante el

montaje, por lo que es mejor que seleccione un lugar

espacioso para efectuar el desembalaje y el montaje.

Abra el cartón y extraiga las partes del nivel

superior.

Consultando la ilustración, asegúrese de que dispone de todas

las partes necesarias.

• Es posible que se suministre un banco o que sea

opcional, dependiendo del lugar de venta del instru-

mento.

Coloque las tres patas (A, B, C).

Emplee unas tijeras o un cortador para sacar el material de

embalaje en el que está envuelta la unidad principal. Luego,

mote las patas en la parte inferior de la unidad principal emplean-

do cuatro tornillos largos de 5 x 20 mm por pata. Consulte con

cuidado la ilustración para asegurarse de que las posiciones de las

patas (A) y (B) no se invierten. Asegúrese también que existe un

espacio mínimo entre las bridas de las patas (A) y (B) y el basti-

dor metálico en la parte inferior de la unidad principal (los torni-

llos que se unen las patas a este bastidor se instalarán después, en

el paso

5 x 20 mm long screws

Lange Schrauben (5 x 20 mm)

Vis longue 5 x 20 mm

Tornillos largos de 5 x 20 mm

Attach the pedal box (D).

Before attaching the pedal box, connect the pedal cord. Pull

the pedal plug out from the hole in the base plate and plug it into

the socket in the bottom of the main unit with the lug on the plug

facing the rear of the main unit (refer to the illustration). If the

plug won’t go in properly, don’t force it … check the plug

orientation and try again.

Making sure that the pedal cord doesn’t get caught between

the base plate and main unit, carefully lower the pedal box

assembly onto the bottom of the main unit and line up the screw

holes. Finally, attach the pedal box with four 5 x 20 mm long

screws.

Turn over the instrument and packing.

Make sure that the three legs are firmly attached, then using

the front legs (A) and (B) for support, turn over the instrument

and packing so that the carton is on top of the instrument.

Den Pedalkasten (D) montieren.

Schließen Sie vor der Montage des Pedalkastens zunächst das

Pedalkabel an. Führen Sie den Kabelstecker durch das Loch in

der Grundplatte, um ihn dann, mit der Führungsnase zur Rücksei-

te des Instruments weisend, an die Buchse an der Unterseite an-

zuschließen (siehe Abbildung). Wenn der Stecker nicht in die

Buchse paßt, bitte nicht mit Gewalt hineinstecken ... prüfen Sie

seine Ausrichtung, und versuchen Sie es dann noch einmal.

Setzen Sie den Pedalkasten nun so auf der Unterseite des

Instruments an, daß das Pedalkabel nicht zwischen Grundplatte

und Instrument eingeklemmt wird und die Schraubenbohrungen

zur Deckung kommen. Schrauben Sie den Pedalkasten dann mit

vier langen Schrauben (5 x 20 mm) fest.

Das Instrument mit dem Karton aufstellen.

Prüfen Sie noch einmal, ob die drei Standbeine fest montiert

sind, und stellen Sie das Instrument dann über die vorderen

Standbeine (A und B) so aufrecht, daß der Karton oben ist.

5 x 20 mm long screws

Lange Schrauben (5 x 20 mm)

Vis longue 5 x 20 mm

Tornillos largos de 5 x 20 mm

Rear Side

Rückseite

Côté arrière

Lado posterior

Keyboard Side

Tastaturseite

Côté clavier

Lado del teclado

Monter le pédalier (D).

Avant de monter le pédalier, raccordez son cordon. Sortir le

connecteur de pédalier de l’orifice de l’embase et le brancher

dans la prise sous de l’instrument, la cosse du connecteur orienté

vers l’arrière de l’instrument (comme indiqué sur l’illustration).

Si la prise est difficile à enclencher, ne pas forcer... vérifier

l’orientation de la prise et essayer à nouveau.

En vérifiant que le cordon du pédalier n’est pas pincé entre

l’embase et l’instrument, abaisser soigneusement l’ensemble de

pédalier en place au bas de l’instrument et l’aligner sur les trous

de vis. Pour finir, monter le pédalier avec quatre vis longues 5 x

20 mm.

Retourner l’instrument et l’emballage.

Vérifier que les trois pieds sont fermement fixés, puis, en

utilisant les pieds avant (A) et (B) comme support, retourner

l’instrument et l’emballage, de manière à ce que le carton se

trouve sur l’instrument.

Coloque la caja de pedales (D).

Antes de montar la caja de pedales, conecte el cable de los

pedales. Tire de la clavija de pedales desde el orificio de la placa

de la base y enchúfelo a la toma de la parte inferior de la unidad

principal con el apéndice de la clavija encarado a la parte poste-

rior de la unidad principal (consulte la ilustración). Si la clavija

no entra correctamente, no la fuerza ... compruebe la orientación

de la clavija e inténtelo de nuevo.

Teniendo cuidado de que el cable de los pedales no queda

pillado entre la placa de la base y la unidad principal, baje con

cuidado el conjunto de la caja de pedales a la parte inferior de la

unidad principal y alinee los orificios de los tornillos. Finalmen-

te, monte la caja de pedales con cuatro tornillos largos de 5 x 20

mm.

Dé la vuelta al instrumentos y al embalaje.

Asegúrese de que las tres patas estén firmemente unidas, y

empleando las patas frontales (A) y (B) como soporte, dé la vuel-

ta al instrumento y al embalaje de modo que el cartón quede en la

parte superior del instrumento.

Remove the carton and packing material.

Lift and remove the carton, then remove the remaining

packing material from the main unit.

Attach the front leg/frame screws.

Firmly attach the front legs (A) and (B) to the frame on the

bottom of the main unit using two 5 x 20 mm long screws for

each leg.

Voltage Selector

Check the setting of the voltage selector which is provided in

some areas. To set the selector for 110V, 127V, 220V or 240V

main voltages, use a “minus” screwdriver to rotate the selector

dial so that the correct voltage for your region appears next to the

pointer on the panel. The voltage selector is set at 240V when the

unit is initially shipped.

Den Karton und das Verpackungsmaterial

entfernen.

Heben Sie zunächst den Karton weg, und entfernen Sie dann

die beiden Formstücke und das übrige Verpackungsmaterial.

Die vorderen Standbeine mit dem Rahmen

verschrauben.

Schrauben Sie die vorderen Standbeine (A und B) mit jeweils

zwei langen Schrauben (5 x 20 mm) gut am Rahmen an der

Unterseite des Instruments fest.

Den Spannungswähler einstellen.

Stellen Sie den Spannungswähler (falls vorhanden) auf die

örtliche Netzspannung ein. Zum Verstellen drehen Sie den

Spannungswähler mit einem Schlitzschraubendreher, bis der

richtige Spannungswert (110, 127, 220 oder 240) an der

Pfeilmarkierung steht. Bei der Auslieferung werden alle

Instrumente mit Spannungswähler auf “240” voreingestellt.

Retirer le carton et les matériaux de garni-

ture.

Soulever le carton et le retirer, puis retirer les matériaux d’em-

ballage qui restaient sur l’instrument.

Fixer les vis pieds avant/châssis.

Fixer fermement, sous l’instrument, les pieds avant (A) et (B)

au châssis avec deux vis longues 5 x 20 mm par pied.

Sélecteur de tension.

Vérifiez le réglage du sélecteur de tension qui est prévu pour

certaines régions. Pour régler le sélecteur sur 110 V, 127 V, 220

V ou 240 V, utilisez un tournevis à lame plate pour tourner le

cadran du sélecteur afin de mettre l’indication correspondant à la

tension de votre région vis à vis du repère triangulaire situé sur le

panneau. Le sélecteur de tension est réglé sur 240 V au départ

d’usine.

Extraiga el cartón y el material de embalaje.

Levante y extraiga el cartón, y saque entonces el material de

embalaje restante de la unidad principal.

Monte los tornillos de las patas frontales/

bastidor.

Coloque firmemente las patas frontales (A) y (B) en el basti-

dor en la parte inferior de la unidad principal empleando dos

tornillos largos de 5 x 20 mm para cada pata.

Selector de tensión.

Compruebe el ajuste del selector de tensión que se incorpora

para ciertos destinos. Para ajustar el selector a 110V, 127V,

220V ó 240V de la red de alimentación, emplee un destornillador

de cabeza recta “-” para girar el selector de modo que la tensión

correcta de su zona aparezca al lado del indicador del panel. El

selector de tensión se ajusta a 240V cuando la unidad sale de

fábrica.

5 x 20 mm long screws

Lange Schrauben (5 x 20 mm)

Vis longue 5 x 20 mm

Tornillos largos de 5 x 20 mm

5 x 20 mm long screws

Lange Schrauben (5 x 20 mm)

Vis longue 5 x 20 mm

Tornillos largos de 5 x 20 mm

● A voltage selector is provided in some

areas.

● Spannungswähler

(nur in bestimmten Verkaufsgebieten)

● Un sélecteur de tension est prévu pour

certaines régions

● El selector de tensión está provisto para

ciertos destinos.

240

127

110



220



Attach the cord holders and plug in the AC

cord.

Remove the protective backing from the adhesive surface of

the cord holders, and attach at approximately the locations shown

in the illustration. Plug the main-unit end of the AC cord into the

corresponding socket on the bottom of the main unit, then secure

the cord with the cord holders.

A plug adaptor may be also provided in some areas to match

the pin configuration of the AC wall outlets in your area.

Set the adjuster.

For stability, an adjuster is provided on the bottom of the

pedal box (D). Rotate the adjuster until it comes in firm contact

with the floor surface. The adjuster ensures stable pedal operation

and facilitates pedal effect control. If the adjuster is not in firm

contact with the floor surface, distorted sound may result.

■ After completing the assembly, please

check the following.

● Are there any parts left over?

m Review the assembly procedure and correct any errors.

● Is the Clavinova clear of doors and other movable fixtures?

m Move the Clavinova to an appropriate location.

● Does the Clavinova make a rattling noise when you shake it?

m Tighten all screws.

● Does the pedal box rattle or give way when you step on the

pedals?

m Turn the adjuster so that it is set firmly against the floor.

● Are the pedal and power cords inserted securely into the

sockets?

m Check the connection.

● If the main unit creaks or is otherwise unsteady when you play

on the keyboard, refer to the assembly diagrams and retighten

all screws.

Die Kabelhalter anbringen und das Netz-

kabel anschließen.

Ziehen Sie das Schutzpapier von der Klebefläche der

Kabelhalter ab, und bringen Sie die Halter ungefähr an den in der

Abbildung gezeigten Stellen an. Stecken Sie den kleineren Stek-

ker des Netzkabels in die entsprechende Buchse an der Unterseite

des Instruments, um das Kabel dann in die Kabelhalter zu legen.

In manchen Gebieten wird ein Steckerdapter mitgeliefert, um

den Anschluß an die evtl. unterschiedlich geformte Steckdose zu

ermöglichen.

Den Pedalfuß einstellen.

Um dem Pedalkasten (D) mehr Standfestigkeit zu geben, ist er

mit einem verstellbaren Pedalfuß ausgestattet. Drehen Sie diesen

Fuß heraus, bis er fest auf der Bodenfläche steht. Der Pedalfuß

stabilisiert den Pedalkasten und ermöglicht eine präzise Pedal-

betätigung. Wenn der Pedalfuß nicht fest auf dem Boden steht,

können Klangverzerrungen auftreten.

■ Wenn der Zusammenbau beendet ist, prü-

fen Sie bitte folgende Dinge:

● Sind Teile übrig geblieben?

m Gehen Sie den Vorgang des Zusammenbaus noch einmal durch und

korrigieren Sie eventuelle Fehler.

● Befindet sich das Clavinova weit genug von Türen und anderen

beweglichen Vorrichtungen entfernt?

Bewegen Sie das Clavinova an einen entsprechend sicheren Ort.

● Macht das Clavinova Klappergeräusche, wenn Sie es schütteln?

m Ziehen Sie alle Schrauben fest.

● Klappert der Pedalkasten oder gibt er nach, wenn Sie das Pedal

treten?

m Drehen Sie den Höhenversteller, bis er fest auf dem Fußboden steht.

● Sind Pedal-und Netzkabel richtig an den Buchsen angeschlos-

sen?

m Prüfen Sie die Verbindung.

● Wenn die Haupteinheit knarrt oder beim Spielen wackelt, be-

trachten Sie die Abbildungen und ziehen Sie alle Schrauben

noch einmal nach.

● Cord holders

● Kabelhalter

● Serre-câble

● Soportes de cable

• When moving the instrument after assembly,

always hold the lower surface of the main unit,

NEVER the lid or keyboard cover. Improper

handling can result in damage to the instrument or

personal injury.

• Fassen Sie zum Umstellen des Instruments nach

dem Zusammenbau stets unter das Gehäuse;

heben Sie es niemals am Gehäuse- oder

Tastaturdeckel. Bei Nichtbeachtung dieses Punkts

kann das Instrument beschädigt und im Extremfall

eine Verletzung hervorgerufen werden.

• Pour déplacer l’instrument après le montage,

toujours tenir l’instrument par la surface inférieure,

JAMAIS par le couvercle ou le protège-clavier.

Une mauvaise manipulation peut provoquer des

dommages ou des blessures.

• Cuando mueva el instrumento después del

montaje, sostenga siempre la superficie inferior

de la unidad principal. NUNCA por la tapa ni

cubierta del teclado. La manipulación indebida

puede causar daños en el instrumento o

personales.

Fixer les serre-fils et brancher le cordon de

l’alimentation secteur.

Retirer le film protecteur des surfaces adhésives aux serre-fils

et les fixer approximativement aux emplacements indiqués sur

l’illustration. Brancher l’extrémité instrument du cordon secteur

dans la prise correspondante au bas de l’instrument et fixer le

cordon avec les serre-fils.

Un adaptateur de prise peut également être fourni dans certai-

nes régions pour pouvoir brancher le cordon à la prise secteur

murale.

Régler la hauteur du pédalier

Pour assurer la stabilité, un dispositif de réglage du pédalier

(D) est équipé. Tourner ce dispositif jusqu’à ce qu’il soit en con-

tact ferme avec le sol. Ce dispositif assure la stabilité du pédalier

pendant son utilisation et facilite la commande au pied des effets.

Si ce dispositif n’est pas fermement en contact avec le sol, le son

pourra être déformé.

■ Lorsque le montage est terminé, veuillez

mener à bien les vérifications suivantes.

● Reste-t-il des pièces non utilisées?

m Passer en revue la procédure de montage et corriger toute erreur

éventuelle.

● Le Clavinova est-il placé à l’écart des portes et de toute autre

structure mobile?

m Déplacer le Clavinova vers un emplacement approprié.

● Lorsque vous secouez quelque peu le Clavinova, entendez-

vous un cliquetis?

m Serrer convenablement toutes les vis.

● Le pédalier fait-il du bruit ou s’écarte-t-il lorsque vous appuyez

sur les pédales?

m Tourner le stabilisateur de sorte qu’il repose fermement sur le sol.

● Les cordons des pédales et d’alimentation sont-ils bien

enfoncés dans les prises?

m Vérifier toutes les connexions.

● Si la partie principale de l’appareil craque ou est instable

lorsque vous jouez sur le clavier, consulter les diagrammes de

montage et resserrer toutes les vis.

Monte los soportes de cable y enchufe el

cable de CA

Extraiga el dorso protector de la superficie adhesiva de los

soportes de cable, y colóquelos aproximadamente en los lugares

mostrados en la ilustración. Enchufe e extremo de la unidad

principal del cable de CA en la toma correspondiente de la parte

inferior de la unidad principal, y fije el cable con los soportes de

cables.

En algunas zonas puede suministrarse también un adaptador

para adaptar la configuración de las patillas de los tomacorrientes

de CA de su localidad.

Ajuste el ajustador.

Para mayor estabilidad, se proporciona un ajustador en la parte

inferior de la caja de pedales (D). Gire el ajustador hasta que se

ponga firmemente en contacto con la superficie del suelo. El

ajustador asegura la operación estable de lo pedales y facilita el

control de efectos de los pedales. Si el ajustador no está firme-

mente en contacto con la superficie del suelo, puede producirse

sonido distorsionado.

■ Cuando haya concluido el montaje,

compruebe los siguientes puntos:

● ¿Ha quedado alguna pieza sin instalar?

m Revise el procedimiento de montaje y corrija cualquier error que se

haya podido cometer.

● ¿Está el Clavinova alejado del recorrido de puertas y muebles?

m Traslade el Clavinova a una posición adecuada.

● ¿Suena algún ruido de holgura cuando se mueve el Clavinova?

m Apriete con firmeza todos los tornillos.

● ¿Vibra o cede la caja de pedales cuando se pisan los pedales?

m Gire el ajustador hasta que se apoye firmemente sobre el suelo.

● ¿Están perfectamente insertados los cables de pedal y alimen-

tación en los conectores?

m Revise las conexiones.

● Si la unidad principal cruje o presenta algún signo de inestabili-

dad cuando se toca el teclado, consulte los esquemas de

montajee y vuelva a apretar todos los tornillos.

Default

Voice PIANO 1

Dual Mode OFF

Split Mode OFF

Split Mode Left-hand Voice

STRINGS

Reverb Type ROOM

Reverb Depth 10

Effect OFF

Effect Depth

Preset for each voice

Transpose 0

Touch Sensitivity MEDIUM

Touch Volume in the FIXED Mode

Metronome OFF

Metronome Volume 10

Tempo 120

Function

Function Default

F1 : Tuning A3=440Hz

F2 : Scale 1 (Equal Temperament)

F3.1 : Dual Balance

Preset for each voice combination

F3.2 : Dual Detune

Preset for each voice combination

F3.3/F3.4 : Dual Octave Shift

Preset for each voice combination

F3.5/F3.6 : Dual Effect Depth

Preset for each voice combination

F3.7 : Slow-attack Strings OFF

F4.1 : Split Point F#2

F4.2 : Split Balance

Preset for each voice combination

F4.3/F4.4 : Split Octave Shift

Preset for each voice combination

F4.5/F4.6 : Split Effect Depth

Preset for each voice combination

F4.7 : Damper Mode ALL

F5.1 : Metronome Beat 0 (no accent)

F5.2 : Metronome Volume 10

F6 : Left Pedal Mode 1 (soft pedal)

F7 :

Piano Song Part Cancel Volume

F8.1 : MIDI Transmit Channel 1

F8.2 : MIDI Receive Channel ALL

F8.3 : Local Control ON

F8.4 :

Program Change Send & Receive

F8.5 :

Control Change Send & Receive

F8.6 : MIDI Transmit Transpose 0

F9 : Backup All OFF

Voice Demo Tune Titles

Voice Name Title Composer

PIANO 1 Ballad No. 1 G minor op. 23 F. F. Chopin

PIANO 2 Lake Louise Y. Kuramoto

CLAVINOVA TONE Consolation No. 3 F. Liszt

HARPSICHORD “Allemande” from French Suite No. 5 BWV816 J. S. Bach

STRINGS Salut d’amour op.12 E. Elgar

PIPE OPRGAN 1 “Prelude No.1 C major” from 8 Short Prelude and Fugues BWV553 — 560 J. S. Bach

PIPE ORGAN 2 Hymn “Allein Gott in der Höh’ sei Ehr’ ” F. W. Zachow

* The demonstration pieces listed above are short excerpts from the original

RATION).

* Bei den oben aufgeführten Demo-Stücken handelt es sich um kurze Auszüge

1997 by YAMAHA CORPORATION).

* Les morceaux de démonstration énumérés ci-dessus sont de courts extraits

des compositions originales. Les autres morceaux de démonstration sont des

* Las piezas de demostración arriba mencionadas son pasajes cortos de las

por YAMAHA CORPORATION).

Piano Song Titles

Demo Song List/Verzeichnis der Demo-Songs/

Liste des morceaux de démonstration/Lista de canciones de demostración

Default Setting List/Liste der Vorgabeeinstellungen/

Liste des réglages par défaut/Lista de ajustes de fábrica

No. Title Composer

16 The Harvest Time G. Lange

17 Impromptu op.90-2 F. P. Schubert

18 Waltz op.64-2 F. F. Chopin

19 Nocturne op.9-2 F. F. Chopin

20 Sonata C major K.545 1st Mov. W. A. Mozart

21 1ère Arabesque C. A. Debussy

22 La Prière d’une Vierge T. Badarzewska

23 Frühlingslied J. L. F. Mendelssohn

24 La Viollette L. Streabbog

25 Ecossaise G major L. v. Beethoven

26 Arabesque J. F. F. Burgmüller

27 The Entertainer S. Joplin

28 Gavotte G. P. Telemann

29 Little Serenade J. Haydn

30 Allegro B major K.3 W. A. Mozart

No. Title Composer

1 Für Elise L. v. Beethoven

2 Dolly’s Dreaming and Awakening T. Oesten

3 Blumenlied G. Lange

“Marche Turke” from Sonata A major K.331”

W. A. Mozart

5 Waltz “Petit Chien” op.64-1 F. F. Chopin

6 Türkischer Marsch L. v. Beethoven

7 SpinnerLied A. Ellmenreich

8 Alpenabendröte T. Oesten

9 Sonatine Anh.6 L. v. Beethoven

10 Melodie op.68-1 R. A. Schumann

11 Heidenröslein G. Lange

12 La chevaleresque J. F. F. Burgmüller

13 Minuet G major BWV Anh.114 J. S. Bach

14 Ronde alla Turca J. F. F. Burgmüller

15 Minuet G minor K.1e W. A. Mozart

KEYBOARD

POLYPHONY

VOICE SELECTORS

REVERB

TOUCH SENSITIVITY

RECORDER

PEDAL CONTROLS

OTHER CONTROLS

JACKS/CONNECTORS

INPUT & OUTPUT

LEVEL/IMPEDANCE

MAIN AMPLIFIERS

SPEAKERS

DIMENTIONS

Lid down

(W x D x H)

Lid up

WEIGHT

CLP-555

88 KEYS (A-1 ~ C7)

32 NOTES MAX.

PIANO 1, PIANO 2, CLAVINOVA TONE, E. PIANO 1, E. PIANO 2, HARPSICHORD,

STRINGS, PIPE ORGAN 1, PIPE ORGAN 2, VARIATION

ROOM, HALL 1, HALL 2, STAGE

HARD, MEDIUM, SOFT, FIXED

1, 2, START/STOP, REC

SOFT, SOSTENUTO, DAMPER

MASTER VOLUME, FUNCTION, TRANSPOSE, SPLIT, EFFECT,

METRONOME, TEMPO/SONG [s]/[t], LED Display, DEMO/PIANO SONG

PHONES x 2, AUX OUT L/L+R & R, AUX IN L/L+R & R,

MIDI IN/OUT/THRU, HOST SELECT, TO HOST

AUX OUT: Output impedance 600 Ω

AUX IN: Input impedance 10 kΩ / Input sensitivity -10 dBm

30W x 2

14 cm x 2 , 5 cm x 2

1417 x 870 x 884.4 mm

(55-3/4" x 34-1/4" x 34-13/16")

1417 x 870 x 1228.9 mm

(55-3/4" x 34-1/4" x 48-3/8")

72 kg (158.7 lbs.)

* Specifications subject to change without notice.

* Änderungen ohne Vorankündigung vorbehalten.

* Sous toute réserve de modification des caractéristiques sans préavis.

* Especificaciones sujetas a cambios sin previo aviso.

Specifications/Technische Daten/Caractéristiques techniques/Especificaciones

WARNING- When using any electrical or electronic prod-

uct, basic precautions should always be followed. These pre-

cautions include, but are not limited to, the following:

1. Read all Safety Instructions, Installation Instructions,

Special Message Section items, and any Assembly Instructions

found in this manual BEFORE marking any connections, in-

cluding connection to the main supply.

2. Main Power Supply Verification: Yamaha products are

manufactured specifically for the supply voltage in the area

where they are to be sold. If you should move, or if any doubt

exists about the supply voltage in your area, please contact

your dealer for supply voltage verification and (if applicable)

instructions. The required supply voltage is printed on the

name plate. For name plate location, please refer to the graphic

found in the Special Message Section of this manual.

3. This product may be equipped with a polarized plug

(one blade wider than the other). If you are unable to insert the

plug into the outlet, turn the plug over and try again. If the

problem persists, contact an electrician to have the obsolete

outlet replaced. Do NOT defeat the safety purpose of the plug.

4. Some electronic products utilize external power sup-

plies or adapters. Do NOT connect this type of product to any

power supply or adapter other than one described in the owners

manual, on the name plate, or specifically recommended by

Yamaha.

5. WARNING: Do not place this product or any other

objects on the power cord or place it in a position where any-

one could walk on, trip over, or roll anything over power or

connecting cords of any kind. The use of an extension cord is

not recommended! If you must use an extension cord, the

minimum wire size for a 25' cord (or less) is 18 AWG. NOTE:

The smaller the AWG number, the larger the current handling

capacity. For longer extension cords, consult a local electri-

cian.

6. Ventilation: Electronic products, unless specifically

designed for enclosed installations, should be placed in loca-

tions that do not interfere with proper ventilation. If instruc-

tions for enclosed installations are not provided, it must be

assumed that unobstructed ventilation is required.

7. Temperature considerations: Electronic products

should be installed in locations that do not significantly con-

tribute to their operating temperature. Placement of this prod-

uct close to heat sources such as; radiators, heat registers and

other devices that produce heat should be avoided.

8. This product was NOT designed for use in wet/damp loca-

tions and should not be used near water or exposed to rain. Exam-

ples of wet/damp locations are; near a swimming pool, spa, tub,

sink, or wet basement.

9. This product should be used only with the components

supplied or; a cart, rack, or stand that is recommended by the

manufacturer. If a cart, rack, or stand is used, please observe all

safety markings and instructions that accompany the accessory

product.

10. The power supply cord (plug) should be disconnected from

the outlet when electronic products are to be left unused for ex-

tended periods of time. Cords should also be disconnected when

there is a high probability of lightening and/or electrical storm

activity.

11. Care should be taken that objects do not fall and liquids are

not spilled into the enclosure through any openings that may exist.

12. Electrical/electronic products should be serviced by a

qualified service person when:

a. The power supply cord has been damaged; or

b. Objects have fallen, been inserted, or liquids have been

spilled into the enclosure through openings; or

c. The product has been exposed to rain: or

d. The product dose not operate, exhibits a marked change

in performance; or

e. The product has been dropped, or the enclosure of the

product has been damaged.

13. Do not attempt to service this product beyond that de-

scribed in the user-maintenance instructions. All other servicing

should be referred to qualified service personnel.

14. This product, either alone or in combination with an ampli-

fier and headphones or speaker/s, may be capable of producing

sound levels that could cause permanent hearing loss. DO NOT

operate for a long period of time at a high volume level or at a

level that is uncomfortable. If you experience any hearing loss or

ringing in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

15. Some Yamaha products may have benches and/or acces-

sory mounting fixtures that are either supplied as a part of the

product or as optional accessories. Some of these items are de-

signed to be dealer assembled or installed Please make sure that

benches are stable and any optional fixtures (where applicable) are

well secured BEFORE using. Benches supplied by Yamaha are

designed for seating only. No other uses are recommended.

INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,

AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.

IMPORTANT SAFETY INSTRUCTIONS

PLEASE KEEP THIS MANUAL

92-469-2

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Nie-

derlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

For details of products, please contact your nearest Yamaha or the

authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha

ou au distributeur le plus proche de vous figurant dans la liste suivante.

ITALY

Yamaha Musica Italia S.P.A.,

Home Keyboard Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN

Yamaha-Hazen Electronica Musical, S.A.

Jorge Juan 30, 28001, Madrid, Spain

Tel: 91-577-7270

PORTUGAL

Valentim de Carvalho CI SA

Estrada de Porto Salvo, Paço de Arcos 2780 Oeiras,

Portugal

Tel: 01-443-3398/4030/1823

GREECE

Philippe Nakas S.A.

Navarinou Street 13, P.Code 10680, Athens, Greece

Tel: 01-364-7111

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1

Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Office

Generatorvej 8B

DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

Warner Music Finland OY/Fazer Music

Aleksanterinkatu 11, P.O. Box 260

SF-00101 Helsinki, Finland

Tel: 0435 011

NORWAY

Narud Yamaha AS

Grini Næringspark 17

N-1345 Østerås, Norway

Tel: 67 14 47 90

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120

IS-128 Reykjavik, Iceland

Tel: 525 5000

OTHER EUROPEAN COUNTRIES

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen, F.R. of

Germany

Tel: 04101-3030

ASIA

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 730-1098

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

16-28, Jalan SS 2/72, Petaling Jaya, Selangor,

Malaysia

Tel: 3-717-8977

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music Asia Pte., Ltd.

Blk 17A Toa Payoh #01-190 Lorong 7

Singapore 1231

Tel: 354-0133

TAIWAN

Kung Hsue She Trading Co., Ltd.

No. 322, Section 1, FuHsing S. Road,

Taipei 106, Taiwan. R.O.C.

Tel: 02-709-1266

THAILAND

Siam Music Yamaha Co., Ltd.

865 Phornprapha Building, Rama I Road,

Patumwan, Bangkok 10330, Thailand

Tel: 2-215-3443

THE PEOPLE’S REPUBLIC OF CHINA

AND OTHER ASIAN COUNTRIES

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2317

NORTH AMERICA

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America,

Keyboard Division

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MIDDLE & SOUTH AMERICA

MEXICO

Yamaha De Mexico S.A. De C.V.,

Departamento de ventas

Javier Rojo Gomez No.1149, Col. Gpe Del

Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.

Tel: 686-00-33

BRASIL

Yamaha Musical Do Brasil LTDA.

Ave. Reboucas 2636, São Paulo, Brasil

Tel: 011-853-1377

PANAMA

Yamaha De Panama S.A.

Edificio Interseco, Calle Elvira Mendez no.10,

Piso 3, Oficina #105, Ciudad de Panama, Panama

Tel: 507-69-5311

OTHER LATIN AMERICAN COUNTRIES

AND CARIBBEAN COUNTRIES

Yamaha Music Latin America Corp.

6101 Blue Lagoon Drive, Miami, Florida 33126,

U.S.A.

Tel: 305-261-4111

MIDDLE EAST

TURKEY/CYPRUS

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen,

F.R. of Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2312

EUROPE

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

IRELAND

Danfay Ltd.

61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin

Tel: 01-2859177

GERMANY/SWITZERLAND

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen,

F.R. of Germany

Tel: 04101-3030

AUSTRIA

Yamaha Music Austria

Schleiergasse 20, A-1100 Wien Austria

Tel: 0222-60203900

THE NETHERLANDS

Yamaha Music Nederland

Kanaalweg 18G, 3526KL, Utrecht, The Netherlands

Tel: 030-2828411

BELGIUM

Yamaha Music Belgium

Keiberg Imperiastraat 8, 1930 Zaventem, Belgium

Tel: 02-7258220

FRANCE

Yamaha Musique France,

Division Claviers

BP 70-77312 Marne-la-Valée Cedex 2, France

Tel: 01-64-61-4000

HEAD OFFICE Yamaha Corporation, Electronic Musical Instrument Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-3255

AFRICA

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2312

OCEANIA

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

17-33 Market Street, South Melbourne, Vic. 3205,

Australia

Tel: 3-699-2388

NEW ZEALAND

Music Houses of N.Z. Ltd.

146/148 Captain Springs Road, Te Papapa,

Auckland, New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2317

[CL] 9

92-469 1

ENVIRONMENTAL ISSUES: Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is ap-

proximately five years. When replacement becomes nec-

essary, contact a qualified service representative to per-

form the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the

manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and con-

sult your dealer before requesting service.

NAME PLATE LOCATION: The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these graph-

ics appears on this page. Please observe all cautions indi-

cated on this page and those indicated in the safety in-

struction section.

See bottom of Keyboard enclosure for graphic symbol markings

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing) in-

structions in the literature accompany-

ing the product.

The lightning flash with arrowhead

symbol, within the equilateral triangle,

is intended to alert the user to the pres-

ence of uninsulated “dangerous volt-

age” within the product’s enclosure that

may be of sufficient magnitude to con-

stitute a risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic prod-

ucts are tested and approved by an independent safety

testing laboratory in order that you may be sure that when

it is properly installed and used in its normal and custom-

ary manner, all foreseeable risks have been eliminated.

DO NOT modify this unit or commission others to do so

unless specifically authorized by Yamaha. Product per-

formance and/or safety standards may be diminished.

Claims filed under the expressed warranty may be denied

if the unit is/has been modified. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the specifications

without notice or obligation to update existing units.

SPECIAL MESSAGE SECTION

Model _____________________________________

Serial No. __________________________________

Purchase Date ______________________________