Zebra LS7708 Referentie gids

Categorie
Streepjescodelezers
Type
Referentie gids
LS7708
Quick Reference Guide
6953007a.fm Page 1 Wednesday, April 15, 2015 3:23 PM
2 LS7708
© 2015 Symbol Technologies, Inc.
Zebra reserves the right to make changes to any product to improve reliability, function,
or design.
Zebra does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under
any patent right or patent, covering or relating to any combination, system, apparatus,
machine, material, method, or process in which Zebra products might be used. An
implied license exists only for equipment, circuits, and subsystems contained in Zebra
products.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol
logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies
company.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
For Australia Only
For Australia Only. This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd.,
71 Robinson Road, #05-02/03, Singapore 068895, Singapore. Our goods come with
guarantees that cannot be excluded under the Australia Consumer Law. You are enti-
tled to a replacement or refund for a major failure and compensation for any other rea-
sonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount
to a major failure. Zebra Technologies Corporation Australia’s limited warranty above is
in addition to any rights and remedies you may have under the Australian Consumer
Law. If you have any queries, please call Zebra Technologies Corporation at
+65 6858 0722. You may also visit our website: http://www.zebra.com
for the most
updated warranty terms.
6953007a.fm Page 2 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 3
Introduction
This Quick Reference Guide is designed to assist during routine LS7708 operation.
Detailed information about unpacking, installation, performance specifications, and
troubleshooting can be found in the LS7708 Product Reference Guide.
Product Description
The LS7708 high performance omni-directional laser scanner reads bar codes
quickly and accurately with a minimum of effort. The scanner includes an Electriconic
Article Surveillance (EAS) antenna, which allows simultaneous bar code reading and
security tag deactivation.
The LS7708 can rest on top of a counter or be attached to a mounting surface.
Operating the LS7708 Scanner
Power
The LS7708 does not have an on/off switch. It’s ready to scan when connected to a
power supply.
Indicator Lights
The scanner employs an LED with a combination of red and green lights to indicate
operation and decode status. The Standard LED Definitions Table on page 13 lists
the different light combinations and their meanings.
If the scanner is not operating normally, contact the technical person in charge of
scanning, or contact Zebra Technologies Support.
Speaker
Volume Control &
Wakeup Button
LED
6953007a.fm Page 3 Wednesday, April 15, 2015 3:23 PM
4 LS7708
Controls
The Volume Control & Wakeup button adjusts the volume of the beeper and wakes the
scanner from rest or sleep mode.
When the scanner is operating, depress this button to adjust the volume. Hold down the
button until the desired volume is obtained (approximately five seconds). There are
three volume levels. The scanner beeps twice at each volume level before cycling to
the next.
If the scanner is in a rest or sleep mode, briefly depressing the Volume Control &
Wakeup button also awakens the scanner.
Connections
The scanners ports are at the bottom of the scanner. Turning the scanner upside down
allows access to the scanner’s ports.
Routing the Cables
The scanner case has several channels to route the outgoing cables so that they are
organized and don’t hinder the scanner’s placement. After placing the cable connectors
in the appropriate scanner ports, route the cables through the nearest channel.
Secondary Scanner
Power Port
EAS Interlock PortRS-232 Aux Port
Host Port
(Synapse) Port
6953007a.fm Page 4 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 5
For a cable with a Y-connector (containing both power and interface connectors):
1. Connect the power and interface cables to the appropriate ports.
2. Route the cables according to the following diagram.
Mounting the Scanner to a Surface
Caution: The LS7708 requires use of the mounting bracket for proper
operation and saftley. Failure to use the bracket can result in
scanner instability.
The LS7708 is designed to sit on top of a counter or be mounted to a wall. The slot on
the back of the scanner accepts a mounting bracket to secure it to the mounting
surface. This bracket accommodates either configuration.
Connections to power and
hand-held scanner ports, side exit:
curl power cable and route it back
towards interface cable.
Connections to power and host
ports, side exit: keep power cable
straight and route it ahead with
interface cable.
Plastic Tab
Rubber Feet
6953007a.fm Page 5 Wednesday, April 15, 2015 3:23 PM
6 LS7708
Attaching the Mounting Bracket
Freestanding Configuration
Use this method if the scanner will not be secured to a mounting surface.
1. Invert the scanner so that its bottom is facing up and the connections are
visible.
2. Connect all interface and power cables to the scanner. Refer to the LS7708
Product Reference Guide for detailed information.
3. Orient the mounting bracket so that the plastic tab is facing downward and
toward the slot on the back of the scanner. The square cushion on the
mounting bracket should be positioned above the power cable.
6953007a.fm Page 6 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 7
4. Tilt the plastic tab into the slot on the scanner, and rotate the opposite edge
downward. As the bracket rotates, push it toward the slot so that the feet of the
bracket lie flat against the scanner’s bottom (see arrows).
5. When the bracket is flat against the scanner bottom, release pressure so that
the feet slide forward into the front of the scanner.
Mounted Configuration
Use this method if the scanner will be secured to a mounting surface.
1. Determine where the LS7708 is going to be mounted.
2. Use a pencil to mark the four mounting holes. (A mounting template is provided
in the LS7708 Product Reference Guide.)
3. Remove all rubber feet (from the bracket or from the scanner).
4. Place the mounting bracket in position over the drilled holes with its flat surface
facing the mounting surface.
6953007a.fm Page 7 Wednesday, April 15, 2015 3:23 PM
8 LS7708
5. Insert four screws through the holes and fasten to the mounting surface.
6. Align the slot at the back of the scanner with the plastic tab on the mounting
bracket.
7. Angle the scanner slightly to allow the bracket plastic tab to slide into the slot.
8. Push the scanner towards the plastic tab and rotate it so that it is perpendicular
to the mounting surface.
9. Release the pressure on the scanner. The bracket locks into place.
6953007a.fm Page 8 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 9
Detaching the Scanner from the Mounting Bracket
To detach the scanner:
1. Grasp the scanner firmly on both sides.
2. Squeeze the back of the scanner slightly while pushing the scanner in the
direction of the slot on the back.
3. Rotate the front of the scanner away from the mounting bracket until the
bracket pops out of the slot.
Scanning Bar Codes
Install and program the scanner. (Refer to the LS7708 Product Reference Guide for
programming instructions.) For assistance, contact the local supplier or Zebra
Technologies Support.
For the best scanning performance, the counter top or surface area covered by the
active scan area should be free of any designs (e.g. stripes or patterns). Ideally, that
area should be a light, solid color. A rastering omni-directional scan pattern provides
rapid, orientation-free scanning.
To scan a bar code:
1. Ensure all cable connections are secure.
2. Orient the item with the bar code facing the scanner window.
3. Move the item through the active scan area in the direction of the arrows, or
place the item in front of the scanner.
4. Upon successful decode, the scanner beeps and the green LED flashes
momentarily.
6953007a.fm Page 9 Wednesday, April 15, 2015 3:23 PM
10 LS7708
Active Scan Area
The active scan area is the area in front of the scanner window in which a bar code can
be decoded. The dotted area represents the active scan area.
Sleep Mode
The scanner automatically enters Sleep mode when it has been inactive for a specified
length of time. The scanner has two levels of sleep: laser and motor. In laser sleep
mode, after ten seconds of inactivity the laser pulses at a 50% rate, and then drops to
3% after a specified time. In motor sleep mode, the scanner is programmed to turn off
the motor and the laser.
The scanner is awakened from either sleep mode by pressing the Volume Control &
Wakeup button. In laser sleep mode, the scanner also is awakened by presenting a bar
code at the scanner window.
6953007a.fm Page 10 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 11
Selecting Beeper Volume
The scanner emits a short beep when it successfully reads a bar code. The volume of
the beep is changed by scanning one of the beeper volume bar codes in the LS7708
Product Reference Guide, or by using the Volume Control & Wakeup button on the front
of the scanner as follows:
1. Press and hold the button for approximately five seconds. The scanner cycles
through three settings (low, medium, high), emitting a two-beep tone at each
setting.
2. To select a particular setting, release the button after the desired 2-beep tone
is heard.
Beeper Definitions
The scanner communicates with the user by emitting different beeper sequences and
patterns. See the Standard Beeper Definitions table for beeper sequences that occur
during both normal scanning and while programming the scanner.
Beeper Sequence Indication
Standard Use
3 short high beeps Power up.
Short high beep A bar code symbol was decoded (if decode
beeper is enabled).
4 long low beeps A transmission error was detected in a scanned
symbol. The data is ignored. This occurs if the
scanner is not properly configured. Check
option setting.
5 low beeps Conversion or format error.
Hi-hi-hi-lo beep RS-232 receive error on RS-232 host or RS-232
auxiliary port.
Code 39 Buffering
Hi-lo beep New Code 39 data was entered into the buffer.
3 long high beeps Code 39 buffer is full.
6953007a.fm Page 11 Wednesday, April 15, 2015 3:23 PM
12 LS7708
Lo-hi-lo beep The Code 39 buffer was erased or there was an
attempt to clear or transmit an empty buffer.
Lo-hi beep A successful transmission of buffered data.
Host Specific
USB only
4 short high beeps Scanner has not completed initialization. Wait
several seconds and scan again.
Scanner gives a power-up
beep after scanning a USB
Device Type.
Communication with the bus must be
established before the scanner can operate at
the highest power level.
This power-up beep occurs
more than once.
The USB bus may put the scanner in a state
where power to the scanner is cycled on and off
more than once. This is normal and usually
happens when the PC cold boots.
RS-232 Host only
1 short high beep A <BEL> character is received and Beep on
<BEL> is enabled.
RS-232 Auxiliary Port only
1 short high beep A complete block of data was received and sent
to the host, either due to a carriage return or
because the two-second serial response
timeout has elapsed.
4 long low beeps A data overrun condition has occurred. Abstain
from scanning data from other ports when large
amounts of data are sent to the RS-232
Auxiliary port.
Beeper Sequence Indication
6953007a.fm Page 12 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 13
LED Definitions
In addition to beeper sequences, the scanner communicates with the user via an LED
display. The Standard LED Definitions table defines LED indications that display during
scanning.
Maintenance
Cleaning the exit window is the only maintenance required. A dirty or scratched window
may affect scanning activity.
Remove any dirt particles with a damp cloth.
Wipe the window with a tissue moistened with ammonia or water.
LED Indication
Off No power is applied to the scanner.
Green The scanner is on and “ready to scan.”
Momentary flash A bar code was successfully decoded.
Slow continuous red flashing,
green on
The scanner is in programming mode.
Fast continuous red flashing,
green on
There is an internal problem; the laser is
shut off for regulatory reasons.
Green on (and laser blinking) Scanner is in Low Power Blink mode.
Red and green on Scanner is in Low Power Motor and Laser
Shutdown mode.
6953007a.fm Page 13 Wednesday, April 15, 2015 3:23 PM
14 LS7708
Troubleshooting
Problem Possible Causes Possible Solutions
The omni-line scan
pattern does not
display when you
follow the directions
for installing the host
cable.
No power to the
scanner.
Ensure the host has power,
and is on. If the scanner uses
a separate power supply,
ensure it’s connected to a
working AC outlet.
Power-up sequence is
incorrect. Refer to the LS7708
Product Reference Guide for
more information.
Interface cable is not
properly connected.
Check for loose cable
connections.
Scan line(s) display,
but bar code cannot
be read.
Scanner is not
programmed to read
the bar code type.
Ensure scanner is
programmed to read the bar
code type you are scanning.
Bar code is damaged. Try scanning other bar codes
of the same bar code type.
Bar code is too far from
scanner.
Move the bar code closer to
the scanner.
The host has disabled
scanning or overridden
parameter settings.
See the technical person in
charge of scanning.
Bar code is
decoded, but not
transmitted to the
host.
Scanner is not
programmed for the
correct host type.
Scan the appropriate host type
bar code.
6953007a.fm Page 14 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 15
Scanned data is
incorrectly displayed
on the host.
Scanner is not
programmed to work
with the host. Check
scanner host type
parameters or editing
options.
Ensure proper host is
selected.
For RS-232, ensure the
scanner’s communication
parameters match the host’s
settings.
For keyboard wedge, ensure
scanner is programmed with
the correct country code and
that the CAPS LOCK key is
off.
Ensure editing options (e.g.,
UPCE-to-UPCA Conversion)
are properly programmed.
Although the green
and red LEDs are
on, the scanner
does not produce
the omni-directional
scan pattern.
The scanner has gone
into the Low Power
“Motor Sleep” Mode.
Press the Volume Control &
Wakeup button to awaken the
unit.
USB or Synapse
host not functioning
properly.
Scanner does not
recognize host.
Remove and reinsert external
power supply to force cable to
autodetect correct host.
NOTE If the symbol still does not scan, contact distributor or contact Zebra
Technologies Support. See the back cover for contact information.
Problem Possible Causes Possible Solutions
6953007a.fm Page 15 Wednesday, April 15, 2015 3:23 PM
16 LS7708
Programming
Generally, the technical person in charge of scanning customizes the scanner for
the particular application using programming bar codes found in the LS7708
Product Reference Guide. If the user is programming the scanner, the LS7708 Product
Reference Guide should be consulted for more information.
Following are some frequently used programming bar codes.
Test
To confirm that your scanner is working properly, scan the UPC-A bar code below.
Verify the Scanner Is Working
NOTE For additional host types, refer to the LS7708 Product Reference
Guide, p/n 72-69531-xx, available at:
http://www.zebra.com/support.
When scanning the desired bar code, cover other bar code on
page.
6953007a.fm Page 16 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 17
Set Defaults
Scanning this bar code sets all parameters to their factory default values.
Set Defaults
Host Type Selection
If a Synapse cable (i.e., part number STIxx-xxxx) is used, the scanner autodetects the
type of host, so there is no need to scan host type selection bar codes.
If a USB interface is used, the scanner autodetects the USB and defaults to the HID
keyboard interface. See page 28 to select the IBM Hand-Held host type. Refer to the
LS7708 Product Reference Guide, p/n 72-69531-01, for additional USB host types.
If a Keyboard Wedge, RS-232, Wand Emulation, or IBM 46XX host is used, select that
host type from the programming bar codes that follow. If Keyboard Wedge is selected,
also select a country keyboard type from the following pages.
Keyboard Wedge Host Type
IBM PC/AT & IBM PC Compatibles
6953007a.fm Page 17 Wednesday, April 15, 2015 3:23 PM
18 LS7708
Country Keyboard Types (Country Codes)
Country keyboard options apply to the Keyboard Wedge interface only.
North American
French
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 18 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 19
Country Keyboard Types (continued)
French Canadian Win95/98
French Canadian XP/2000
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 19 Wednesday, April 15, 2015 3:23 PM
20 LS7708
Country Keyboard Types (continued)
German
Spanish
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 20 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 21
Country Keyboard Types (continued)
Italian
Swedish
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 21 Wednesday, April 15, 2015 3:23 PM
22 LS7708
Country Keyboard Types (continued)
UK English
Japanese
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 22 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 23
Country Keyboard Types (continued)
Brazil Portuguese Windows
RS-232 Host Types
Standard RS-232
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 23 Wednesday, April 15, 2015 3:23 PM
24 LS7708
RS-232 Host Types (continued)
ICL RS-232
Nixdorf RS-232 Mode A
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 24 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 25
RS-232 Host Types (continued)
Nixdorf RS-232 Mode B
Fujitsu RS-232
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 25 Wednesday, April 15, 2015 3:23 PM
26 LS7708
RS-232 Host Types (continued)
OPOS
JPOS
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 26 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 27
USB Host Types
HID Keyboard Emulation
(Common Keyboard Wedge Interfacing)
IBM Hand-Held USB
(For IBM SurePOS 700 Series)
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 27 Wednesday, April 15, 2015 3:23 PM
28 LS7708
IBM 46XX Host Types
Port 5B
Port 9B
NOTE When scanning the desired bar code, cover other bar code on page.
6953007a.fm Page 28 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 29
IBM 46XX Host Types (continued)
Port 17
6953007a.fm Page 29 Wednesday, April 15, 2015 3:23 PM
30 LS7708
Regulatory Information
This guide applies to Model Number: LS7708.
All Zebra devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Any changes or modifications to Zebra equipment, not expressly approved by
Zebra, could void the user's authority to operate the equipment.
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic
injury follow the recommendations below. Consult with your local Health
& Safety Manager to ensure that you are adhering to your company’s
safety programs to prevent employee injury.
Reduce or eliminate repetitive motion
Maintain a natural position
Reduce or eliminate excessive force
Keep objects that are used frequently within easy reach
Perform tasks at correct heights
Reduce or eliminate vibration
Reduce or eliminate direct pressure
Provide adjustable workstations
Provide adequate clearance
Provide a suitable working environment
Improve work procedures.
6953007a.fm Page 30 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 31
Laser Devices
COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR
DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED JUNE
24, 2007 AND IEC 60825-1 (Ed. 2.0), EN60825-1:2007.
The laser classification is marked on one of the labels on the device.
Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose. The following statement is required to comply with US and
international regulations:
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.
Scanner Labeling
CAUTION Use of controls, adjustments or performance of procedures other than
those specified herein may result in hazardous laser light exposure.
6953007a.fm Page 31 Wednesday, April 15, 2015 3:23 PM
32 LS7708
Laser Labels
In accordance with IEC60825-1 and EN60825, the following
information is provided to the user:
Power Supply
Note: Use ONLY a LISTED, Type no. 50-14000 (5Vdc / 2A), or PWRS-14000
(5Vdc / 2A), Direct Plug-In Power supply, marked Class 2 or LPS (IEC60950-1,
SELV). Use of Alternative Power Supply will invalidate any approvals given to this
unit and may be dangerous.
ENGLISH
CLASS 1 CLASS 1 LASER PRODUCT
CLASS 2 LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
HEBREW
DANISH / DANSK
KLASSE 1 KLASSE 1 LASERPRODUKT
KLASSE 2 LASERLYF
KLASSE 2 LASERPRODUKT
ITALIAN / ITALIANO
CLASSE 1 PRODOTTO AL LASER DI CLASSE 1
CLASSE 2 LUCE LASER
SE IKKE IND I STRÅLEN
NON FISSARE IL
RAGGIOPRODOTTO
AL LASER DI CLASSE 2
DUTCH / NEDERLANDS
KLASSE 1 KLASSE-1 LASERPRODUKT
KLASSE 2 LASERLICHT
NIET IN STRAAL STAREN
LASERPRODUKT,
KLASSE-2 LASERPRODUKT
NORWEGIAN / NORSK
KLASSE 1 LASERPRODUKT,KLASSE 1
KLASSE 2 LASERLYS IKKE STIRR INN I LYSSTRÅLEN
LASERPRODUKT, KLASSE 2
FINNISH / SUOMI
LUOKKA 1 LUOKKA 1 LASERTUOTE
LUOKKA 2 LASERVALO
ÄLÄ TUIJOTA SÄDETTÄ
LUOKKA 2 LASERTUOTE
PORTUGUESE / PORTUGUÊS
CLASSE 1 PRODUTO LASER DA CLASSE 1
CLASSE 2 LUZ DE LASER NÃO FIXAR O RAIO LUMINOSO
PRODUTO LASER DA CLASSE 2
FRENCH / FRANÇAIS
CLASSE 1 PRODUIT LASER DE CLASSE 1
CLASSE 2 LUMIERE LASER
NE PAS REGARDER LE RAYON FIXEMENT
PRODUIT LASER DE CLASSE 2
SPANISH / ESPAÑOL
CLASE 1 PRODUCTO LASER DE LA CLASE 1
CLASE 2 LUZ LASER
NO MIRE FIJAMENTE EL HAZ
PRODUIT LASER DE CLASSE 2
GERMAN / DEUTCH
KLASSE 1 LASERPRODUKT DER KLASSE 1
KLASSE 2 LASERSTRAHLEN
NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN
LASERPRODUKT DER KLASSE 2
SWEDISH / SVENSKA
KLASS 1 LASERPRODUKT KLASS 1
KLASS 2 LASERLJUS STIRRA INTE MOT STRÅLEN
LASERPRODUKT KLASS 2
6953007a.fm Page 32 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 33
Radio Frequency Interference Requirements-FCC
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this device is in compliance with all the
applicable Directives, 2004/108/EC, 2006/95/EC and 2011/65/EU. A
Declaration of Conformity may be obtained from
http://www.zebra.com/doc.
Other Countries
Ukraine
6953007a.fm Page 33 Wednesday, April 15, 2015 3:23 PM
34 LS7708
Waste Electrical and Electronic Equipment (WEEE)
English: For EU Customers: All products at the end of their life must be returned to Zebra for
recycling. For information on how to return product, please go to: http://www.zebra.com/weee.
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти трябва
да се връщат на Zebra за рециклиране. За информация относно връщането на
продукти, моля отидете на адрес: http://www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit
spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové
stránce: http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udt-
jent. Læs oplysningerne om returnering af produkter på: http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer
zum Recycling an Zebra zurückgesandt werden. Informationen zur Rücksendung von Pro-
dukten finden Sie unter http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της
διάρκειας ζωής τους,
πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες
σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση
http://www.zebra.com/weee στο ∆ιαδίκτυο.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise
eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun
aadressi: http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a
Zebra al final de su ciclo de vida para que sean reciclados. Si desea más información sobre
cómo devolver un producto, visite: http://www.zebra.com/weee.
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent
être retournés à Zebra pour recyclage. Pour de plus amples informations sur le retour de pro-
duits, consultez : http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita
devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle
modalità di restituzione, visitare il seguente sito Web: http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ
Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu,
skatiet: http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti
utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite:
http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljut-
tatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudni-
valókért látogasson el a http://www.zebra.com/weee weboldalra.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom,
iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna
l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur
naar Zebra te worden teruggezonden voor recycling. Raadpleeg http://www.zebra.com/weee
voor meer informatie over het terugzenden van producten.
6953007a.fm Page 34 Wednesday, April 15, 2015 3:23 PM
Quick Reference Guide 35
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ
do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na
stronie internetowej http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à
Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite:
http://www.zebra.com/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, tre-
buie returnate la Zebra pentru reciclare. Pentru informaţii despre returnarea produsului, acce-
saţi: http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich
životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov náj-
dete na: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju
Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite: http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi
Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoit-
teessa http://www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till
Zebra för återvinning. Information om hur du returnerar produkten finns på
http://www.zebra.com/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya
iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin:
http://www.zebra.com/weee.
6953007a.fm Page 35 Wednesday, April 15, 2015 3:23 PM
If you have a problem using the equipment, contact your facility’s Technical or Systems
Support. If there is a problem with the equipment, they will contact Zebra Support at:
http://www.zebra.com/support.
For the latest version of this guide go to:
http://www.zebra.com/support.
72-69530-07 Revision A - April 2015
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The
Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra
Technologies company.
© 2015 Symbol Technologies, Inc.
Service Information
6953007a.fm Page 36 Wednesday, April 15, 2015 3:23 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Zebra LS7708 Referentie gids

Categorie
Streepjescodelezers
Type
Referentie gids

in andere talen