Yamaha YHT-1810 de handleiding

Categorie
Luidsprekersets
Type
de handleiding
English
YHT-1810 Home Theater Package
Connection Guide
RGLH
Printed in China ZK47400
©
2014 Yamaha Corporation
The Yamaha YHT-1810 Home Theater Package includes everything you need to add great sound
to your home theater. By following the steps in this Connection Guide, you’ll have your home
theater set up in no time and be enjoying music and movies like never before. Part A explains how
to connect the speakers and antenna. Part B explains how to connect various AV components. See
the relevant owner’s manuals for full instructions and precautions.
Caution: Disconnect all components from AC outlets before proceeding.
Part A: Speakers and Antenna
1
Unpack and check the package contents. The following items are necessary to complete this
Connection Guide. See the owner’s manuals for a complete list of supplied items.
AV Receiver (HTR-2067)
Remote control and two batteries
(AAA, R03, UM-4)
FM antenna (FM antenna type depends
on destination country.)
Subwoofer (NS-SWP20)
Front/surround speaker (NS-B20)
Center speaker (NS-C20)
Non-skid pad
Speaker cable
Checking the package contents
x 4
2
The four front and surround
speakers are identical, so it
doesn’t matter which one you use
in each position.
Position the speakers as shown.
See the owner’s manuals for more
information on installing the
speakers.
Positioning the speakers
Front
left
Front
right
Subwoofer
Surround
left
Surround
right
Center
3
Cut the included speaker cable to suitable lengths for the front, center, surround speakers
and subwoofer. You need to make six cables altogether. Remove about 10 mm (3/8 in.) of
insulation from the end of each cable, and then twist the bare strands tightly.
Connect the speaker cables to the front speakers ( ), surround speakers ( ), center
speaker ( ) and subwoofer ( ). Make sure you connect the speakers and subwoofer
with the correct polarity—positive (+) terminals to positive (+) terminals, and negative
(–) terminals to negative (–) terminals.
Front, Surround speakers
Preparing the cables, speakers and subwoofer
Center speaker
Subwoofer
4
AV Receiver
Connect the front speaker ( ) cables to the AV Receiver. Make sure you connect the
speakers with the correct polarity—positive (+) terminals to positive (+) terminals, and
negative (
) terminals to negative (
) terminals.
To front left
speaker
To front right
speaker
Connecting the front speakers
Connecting the center and surround speakers
5
AV Receiver
Connect the center speaker ( ) and surround speaker ( ) cables to the AV Receiver.
Make sure you connect the speakers with the correct polarity—positive (+) terminals
to positive (+) terminals, and negative (–) terminals to negative (–) terminals.
To surround
right speaker
To center
speaker
To surround
left speaker
AV Receiver
6
Subwoofer
Connect the subwoofer ( ) cables to the AV Receiver.
Make sure you connect the subwoofer with the correct polarity—positive (+) terminals
to positive (+) terminals, and negative (–) terminals to negative (–) terminals.
Connecting the subwoofer
Connecting the antenna
7
AV Receiver
Connect the FM antenna ( ) to the AV Receiver, as shown. See the owner’s manuals
for more information about connecting antenna.
FM antenna
Caution: Disconnect all components from AC outlets before proceeding.
Part B: AV Components
Connecting HDMI-capable components
1
AV Receiver TV
If your TV and BD/DVD players or recorders or satellite/cable set-top box have HDMI
jacks, you can connect them via the AV Receiver. Using HDMI cables (not included),
connect the AV Receiver’s HDMI OUT jack to an HDMI input on your TV, and
connect your BD/DVD players or recorders and satellite/cable set-top box to the AV
Receiver’s HDMI 1(BD/DVD) and HDMI 2 jacks, respectively, as shown.
See the owner’s manuals for more information about HDMI.
Connecting your TV
Connecting your BD/DVD players or recorders,
satellite/cable set-top box
AV Receiver
BD/DVD players or
recorders
Satellite/cable set-top box
2
AV Receiver
TV
You can listen to TV audio through the AV Receiver and speakers by connecting an
audio output on your TV to an audio input on the AV Receiver with, for example, an
optical digital audio cable (not included), as shown.
To listen to TV audio, select the appropriate input source on the AV Receiver.
Connecting your TV for audio output
Your TV supports the Audio Return Channel function
If your TV supports ARC (Audio Return Channel), this connection is
unnecessary.
The Audio Return Channel is required the setting of HDMI function of the AV
Receiver before use. For details, see “Information on HDMI” in “HTR-2067
Owner’s Manual”.
Time to enjoy your Yamaha Home Theater Package!
Now, relax and enjoy the great sound of your Yamaha Home Theater Package.
More various functions are available with the
unit.
Refer to the “HTR-2067 Owner’s Manual” for details on effective use of the unit.
Connecting external devices other than BD/DVD players
Various devices, audio players, such as CD players, etc. can be connected to the unit.
Changing input settings with a single key (SCENE function)
This unit has a SCENE function that allows you to turn the power on and change input sources
and sound field programs with one key.
Enjoying sound field programs
You can enjoy multi-channel playback for almost any sound source using various sound field
programs stored on the chip, and a range of sound decoders.
For more detail, see the relevant owner’s manuals for full operating instructions.
3
Set the VOLTAGE SELECTOR
(General model)
Voltages are AC 110-120/220-240 V, 50/60 Hz.
Caution
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local voltage BEFORE plugging the
power cable into the AC wall outlet. Improper setting of
the VOLTAGE SELECTOR may cause damage to this
unit and create a potential fire hazard.
Connect the AC power cable
Select the switch position according to your local voltage using a straight slot
screwdriver.
VOLTAGE SELECTOR
To an AC wall
outlet
(Other models)
Connect the AV Receiver and your
other AV components to suitable AC
outlets.
AV Receiver
Rear Panel
AV Receiver
Rear Panel
4
Playback
Basic playback procedure
1. Turn on external components (TV, BD player,
etc.) connected to this unit.
2. Turn on this unit and select the input source
using Input selector.
3. Play the external component that you have
selected as the source input, or select a radio
station on the tuner.
Refer to the instruction manuals provided with the
external component for details.
4. Press VOLUME +/– to adjust the volume.
To mute the output,
Press MUTE to mute the audio output.
Press MUTE again to unmute.
Input selection
keys
Español
YHT-1810 Paquete Home Theater
Guía de conexión
El Yamaha YHT-1810 Paquete Home Theater incluye todo lo que necesita para añadir sonido de
primera calidad a su home theater. Siguiendo los pasos de esta Guía de conexión, instalará su
home theater en unos momentos y disfrutará como nunca de la música y las películas. En la parte
A se explica cómo conectar los altavoces y la antena. En la parte B se explica cómo conectar
diferentes componentes AV. Consulte las precauciones e instrucciones completas en los manuales
del usuario correspondientes.
Precaución: Antes de continuar, desconecte todos los componentes de las tomas de CA.
Parte A: Altavoces y antena
1
Desembale el paquete y compruebe que contiene todos los elementos. Para completar esta
Guía de conexión, son necesarios los siguientes elementos. En el manual del usuario
encontrará la lista completa de los elementos incluidos.
Receptor AV (HTR-2067)
Mando a distancia y dos pilas
(AAA, R03, UM-4)
Antena de FM
(el tipo de antena de FM depende del
país de destino).
Subwoofer (NS-SWP20)
Altavoz frontal/surround (NS-B20)
Altavoz central (NS-C20)
Tacos antideslizantes
Cable de altavoz
Comprobar el contenido del paquete
x 4
2
Los cuatro altavoces frontales y
surround son idénticos, por lo
que no importa el que utilice en
cada ubicación.
Sitúe los altavoces tal como se
indica. En los manuales del
usuario encontrará más
información acerca de cómo
instalar los altavoces.
Situar los altavoces
Subwoofer
Surround
izquierdo
Surround
derecho
Central
Frontal
izquierdo
Frontal
derecho
3
Corte el cable del altavoz incluido a una longitud adecuada para los altavoces frontales,
central y surround y el subwoofer. Deberá unir seis cables. Pele unos 10 mm del
aislamiento del extremo de cada cable y trence los filamentos descubiertos.
Conecte los cables del altavoz a los altavoces frontales ( ), a los altavoces surround ( ),
al altavoz central ( ) y al subwoofer ( ). Cerciórese de conectar los altavoces y el
subwoofer con la polaridad correcta—los terminales positivos (+) a los terminales
positivos (+), y los terminales negativos (–) a los terminales negativos (–) correctos.
Altavoces
frontales, surround
Preparar los cables, los altavoces y el subwoofer
Altavoz central
Subwoofer
4
Receptor AV
Conectar el altavoz frontal ( ) al receptor AV. Cerciórese de conectar los altavoces
con la polaridad correcta—los terminales positivos (+) a los terminales positivos (+),
y los terminales negativos (
) a los terminales negativos (
).
Al altavoz
frontal
izquierdo
Al altavoz
frontal derecho
Conectar los altavoces frontales
Conectar los altavoces central y surround
5
Receptor AV
Conecte los cables del altavoz central ( ) y del altavoz surround ( ) al receptor AV. Cerciórese
de conectar los altavoces con la polaridad correcta—los terminales positivos (+) a los terminales
positivos (+), y los terminales negativos (–) a los terminales negativos (–).
Al altavoz
surround
derecho
Al altavoz
central
A surround
altavoz
izquierdo
Receptor AV
6
Subwoofer
Conecte los cables del subwoofer ( ) al receptor AV.
Cerciórese de conectar el subwoofer con la polaridad correcta—los terminales positivos
(+) a los terminales positivos (+), y los terminales negativos (–) a los terminales
negativos (–).
Conectar el subwoofer
Conectar la antena
7
Receptor AV
Conecte la antena de FM ( ) al receptor AV, tal como se muestra. En los manuales del
usuario encontrará más información acerca de cómo conectar la antena.
Antena de FM
Precaución: Antes de continuar, desconecte todos los componentes de las tomas de CA.
Parte B: Componentes AV
Conectar componentes compatibles con
HDMI
1
Receptor AV TV
Si su TV y sus reproductores o grabadores de BD/DVD o decodificador por
cable/satélite disponen de jacks HDMI, puede conectarlos a través del receptor AV.
A través de cables HDMI (no incluidos), conecte el jack HDMI OUT del receptor AV
a una entrada HDMI de su TV, y conecte sus reproductores o grabadores de BD/DVD
y el decodificador por cable/satélite a los jacks HDMI 1 (BD/DVD) y HDMI 2 del
receptor AV, respectivamente, tal como se muestra.
Consulte los manuales del usuario para más información acerca de HDMI.
Conectar el TV
Conectar su grabadoras y reproductores BD/DVD,
decodificador por cable/satélite
Receptor AV
Grabadoras y
reproductores BD/DVD
Decodificador cable/satélite
2
Receptor AV
TV
Podrá escuchar audio de TV a través de los altavoces del receptor AV y los altavoces
conectando una salida de audio de su TV a una entrada de audio del receptor AV con,
por ejemplo, un cable de audio digital óptico (no incluido), tal como se muestra.
Para escuchar audio de TV, seleccione la fuente de entrada apropiada en el receptor AV.
Conectar su TV para salida de audio
Su TV admite la función Audio Return Channel (canal de retorno de audio)
Si el TV admite ARC (Audio Return Channel), esta conexión no es necesaria.
Audio Return Channel necesita que se configure la función HDMI del receptor
AV antes de usarlo. Para obtener más información, consulte “Información sobre
HDMI” en el “HTR-2067 Manual de Instrucciones”.
¡Es hora de disfrutar de su Yamaha Paquete Home
Theater!
Ahora, relájese y disfrute del excepcional sonido de su Yamaha Paquete Home Theater.
Existen más funciones variadas en la unidad.
Consulte el “HTR-2067 Manual de Instrucciones” para obtener detalles sobre el uso
eficaz de la unidad.
Conexión de dispositivos externos distintos a los
reproductores BD/DVD
Es posible conectar a la unidad varios dispositivos, como reproductores de CD, etc.
Cambio de los ajustes de entrada con una sola tecla (función SCENE)
Esta unidad dispone de una función SCENE que le permite encenderla y cambiar las fuentes de
entrada y los programas de campo sonoro con una tecla.
Para disfrutar de programas de campo sonoro
Puede disfrutar de reproducción multicanal para casi todas las fuentes de sonido, utilizando
diversos programas de campo sonoro almacenados en el chip y una amplia variedad de
decodificadores de sonido.
Para más detalles, consulte las instrucciones de funcionamiento completas en los manuales del
usuario correspondientes.
3
Conecte el cable de alimentación de CA
Seleccione la posición del conmutador de acuerdo con su tensión local utilizando un
destornillador de punta plana.
Ajuste el VOLTAGE SELECTOR
(Modelo general)
Las tensiones son 110-120/220-240 V CA, 50/60 Hz.
PRECAUCIÓN
El VOLTAGE SELECTOR del panel trasero de esta
unidad debe ajustarse para la tensión dela red eléctrica
local ANTES de enchufar elcable de alimentación a la
toma de CA. Unajuste incorrecto del VOLTAGE
SELECTOR puede causar daños a esta unidad y dar
lugar aun posible peligro de incendio.
VOLTAGE SELECTOR
A una toma
de CA
(Otros modelos)
Conecte el receptor AV y el resto de los
componentes AV a las tomas de CA
correspondientes.
Receptor AV
Panel trasero
Receptor AV
Panel trasero
Reproducción
4
Procedimiento de reproducción básico
1.
Encienda los componentes externos (TV,
reproductor de BD, etc.) conectados aesta unidad
.
2. Encienda esta unidad y seleccione la fuente de
entrada utilizando Selector de entrada.
3. Reproduzca el componente externo que ha
seleccionado como la fuente de entrada
oseleccione una emisora de radio
enelsintonizador.
Para conocer detalles sobre la reproducción,
consulte los manuales de instrucciones
suministrados con elcomponente externo.
4. Pulse VOLUME +/– para ajustar elvolumen.
Para silenciar la salida,
Pulse MUTE para silenciar la salida de audio.
Pulse MUTE de nuevo para anular el silenciamiento.
Teclas
selectoras
de entrada

Documenttranscriptie

YHT-1810 Home Theater Package Connection Guide English The Yamaha YHT-1810 Home Theater Package includes everything you need to add great sound to your home theater. By following the steps in this Connection Guide, you’ll have your home theater set up in no time and be enjoying music and movies like never before. Part A explains how to connect the speakers and antenna. Part B explains how to connect various AV components. See the relevant owner’s manuals for full instructions and precautions. © 2014 Yamaha Corporation Printed in China ZK47400 Caution: Disconnect all components from AC outlets before proceeding. 1 4 Connecting the front speakers AV Receiver Caution: Disconnect all components from AC outlets before proceeding. Checking the package contents To front right speaker Select the switch position according to your local voltage using a straight slot screwdriver. VOLTAGE SELECTOR (General model) Voltages are AC 110-120/220-240 V, 50/60 Hz. Caution The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local voltage BEFORE plugging the power cable into the AC wall outlet. Improper setting of the VOLTAGE SELECTOR may cause damage to this unit and create a potential fire hazard. If your TV and BD/DVD players or recorders or satellite/cable set-top box have HDMI jacks, you can connect them via the AV Receiver. Using HDMI cables (not included), connect the AV Receiver’s HDMI OUT jack to an HDMI input on your TV, and connect your BD/DVD players or recorders and satellite/cable set-top box to the AV Receiver’s HDMI 1(BD/DVD) and HDMI 2 jacks, respectively, as shown. See the owner’s manuals for more information about HDMI. AV Receiver Connect the AC power cable Set the VOLTAGE SELECTOR Connecting HDMI-capable components ● Connecting your TV Part A: Speakers and Antenna 1 3 Part B: AV Components RGLH TV AV Receiver Rear Panel (Other models) Connect the AV Receiver and your other AV components to suitable AC outlets. To front left speaker Connect the front speaker ( ) cables to the AV Receiver. Make sure you connect the speakers with the correct polarity—positive (+) terminals to positive (+) terminals, and negative (–) terminals to negative (–) terminals. 5 Connecting the center and surround speakers AV Receiver ● Connecting your BD/DVD players or recorders, satellite/cable set-top box x4 AV Receiver AV Receiver Rear Panel Satellite/cable set-top box 4 Unpack and check the package contents. The following items are necessary to complete this Connection Guide. See the owner’s manuals for a complete list of supplied items. AV Receiver (HTR-2067) Remote control and two batteries (AAA, R03, UM-4) FM antenna (FM antenna type depends on destination country.) 2 Positioning the speakers Front right Front left Center Subwoofer To surround right speaker 3 Basic playback procedure To surround left speaker Input selection keys 6 BD/DVD players or recorders 3. Play the external component that you have selected as the source input, or select a radio station on the tuner. Refer to the instruction manuals provided with the external component for details. Connecting the subwoofer Subwoofer AV Receiver The four front and surround speakers are identical, so it doesn’t matter which one you use in each position. 2 Connecting your TV for audio output You can listen to TV audio through the AV Receiver and speakers by connecting an audio output on your TV to an audio input on the AV Receiver with, for example, an optical digital audio cable (not included), as shown. To listen to TV audio, select the appropriate input source on the AV Receiver. AV Receiver Surround right More various functions are available with the unit. Refer to the “HTR-2067 Owner’s Manual” for details on effective use of the unit. Connect the subwoofer ( ) cables to the AV Receiver. Make sure you connect the subwoofer with the correct polarity—positive (+) terminals to positive (+) terminals, and negative (–) terminals to negative (–) terminals. 7 Center speaker 4. Press VOLUME +/– to adjust the volume. To mute the output, Press MUTE to mute the audio output. Press MUTE again to unmute. TV Preparing the cables, speakers and subwoofer Front, Surround speakers 1. Turn on external components (TV, BD player, etc.) connected to this unit. 2. Turn on this unit and select the input source using Input selector. Connect the center speaker ( ) and surround speaker ( ) cables to the AV Receiver. Make sure you connect the speakers with the correct polarity—positive (+) terminals to positive (+) terminals, and negative (–) terminals to negative (–) terminals. Position the speakers as shown. See the owner’s manuals for more information on installing the speakers. Surround left Playback To center speaker Subwoofer (NS-SWP20) Front/surround speaker (NS-B20) Center speaker (NS-C20) Non-skid pad Speaker cable To an AC wall outlet Connecting the antenna AV Receiver Connecting external devices other than BD/DVD players Various devices, audio players, such as CD players, etc. can be connected to the unit. Your TV supports the Audio Return Channel function • If your TV supports ARC (Audio Return Channel), this connection is unnecessary. • The Audio Return Channel is required the setting of HDMI function of the AV Receiver before use. For details, see “Information on HDMI” in “HTR-2067 Owner’s Manual”. Changing input settings with a single key (SCENE function) This unit has a SCENE function that allows you to turn the power on and change input sources and sound field programs with one key. Enjoying sound field programs You can enjoy multi-channel playback for almost any sound source using various sound field programs stored on the chip, and a range of sound decoders. Subwoofer • Cut the included speaker cable to suitable lengths for the front, center, surround speakers and subwoofer. You need to make six cables altogether. Remove about 10 mm (3/8 in.) of insulation from the end of each cable, and then twist the bare strands tightly. • Connect the speaker cables to the front speakers ( ), surround speakers ( ), center speaker ( ) and subwoofer ( ). Make sure you connect the speakers and subwoofer with the correct polarity—positive (+) terminals to positive (+) terminals, and negative (–) terminals to negative (–) terminals. For more detail, see the relevant owner’s manuals for full operating instructions. FM antenna Connect the FM antenna ( ) to the AV Receiver, as shown. See the owner’s manuals for more information about connecting antenna. Time to enjoy your Yamaha Home Theater Package! Now, relax and enjoy the great sound of your Yamaha Home Theater Package. YHT-1810 Paquete Home Theater Guía de conexión Español El Yamaha YHT-1810 Paquete Home Theater incluye todo lo que necesita para añadir sonido de primera calidad a su home theater. Siguiendo los pasos de esta Guía de conexión, instalará su home theater en unos momentos y disfrutará como nunca de la música y las películas. En la parte A se explica cómo conectar los altavoces y la antena. En la parte B se explica cómo conectar diferentes componentes AV. Consulte las precauciones e instrucciones completas en los manuales del usuario correspondientes. Precaución: Antes de continuar, desconecte todos los componentes de las tomas de CA. 1 4 Conectar los altavoces frontales Parte A: Altavoces y antena Conecte el cable de alimentación de CA Seleccione la posición del conmutador de acuerdo con su tensión local utilizando un destornillador de punta plana. Ajuste el VOLTAGE SELECTOR Conectar componentes compatibles con HDMI ● Conectar el TV Comprobar el contenido del paquete Al altavoz frontal derecho Receptor AV Al altavoz frontal izquierdo VOLTAGE SELECTOR (Modelo general) Las tensiones son 110-120/220-240 V CA, 50/60 Hz. PRECAUCIÓN El VOLTAGE SELECTOR del panel trasero de esta unidad debe ajustarse para la tensión dela red eléctrica local ANTES de enchufar elcable de alimentación a la toma de CA. Unajuste incorrecto del VOLTAGE SELECTOR puede causar daños a esta unidad y dar lugar aun posible peligro de incendio. Si su TV y sus reproductores o grabadores de BD/DVD o decodificador por cable/satélite disponen de jacks HDMI, puede conectarlos a través del receptor AV. A través de cables HDMI (no incluidos), conecte el jack HDMI OUT del receptor AV a una entrada HDMI de su TV, y conecte sus reproductores o grabadores de BD/DVD y el decodificador por cable/satélite a los jacks HDMI 1 (BD/DVD) y HDMI 2 del receptor AV, respectivamente, tal como se muestra. Consulte los manuales del usuario para más información acerca de HDMI. Receptor AV Precaución: Antes de continuar, desconecte todos los componentes de las tomas de CA. 1 3 Parte B: Componentes AV Receptor AV Panel trasero (Otros modelos) Conecte el receptor AV y el resto de los componentes AV a las tomas de CA correspondientes. TV Conectar el altavoz frontal ( ) al receptor AV. Cerciórese de conectar los altavoces con la polaridad correcta—los terminales positivos (+) a los terminales positivos (+), y los terminales negativos (–) a los terminales negativos (–). 5 Conectar los altavoces central y surround Receptor AV Receptor AV Desembale el paquete y compruebe que contiene todos los elementos. Para completar esta Guía de conexión, son necesarios los siguientes elementos. En el manual del usuario encontrará la lista completa de los elementos incluidos. Receptor AV (HTR-2067) Mando a distancia y dos pilas (AAA, R03, UM-4) Antena de FM (el tipo de antena de FM depende del país de destino). 2 Surround izquierdo 3 Central Subwoofer Surround derecho Decodificador cable/satélite A surround altavoz izquierdo Teclas selectoras de entrada Conectar el subwoofer 3. Reproduzca el componente externo que ha seleccionado como la fuente de entrada oseleccione una emisora de radio enelsintonizador. Para conocer detalles sobre la reproducción, consulte los manuales de instrucciones suministrados con elcomponente externo. Subwoofer 2 Conectar su TV para salida de audio Podrá escuchar audio de TV a través de los altavoces del receptor AV y los altavoces conectando una salida de audio de su TV a una entrada de audio del receptor AV con, por ejemplo, un cable de audio digital óptico (no incluido), tal como se muestra. Para escuchar audio de TV, seleccione la fuente de entrada apropiada en el receptor AV. Sitúe los altavoces tal como se indica. En los manuales del usuario encontrará más información acerca de cómo instalar los altavoces. Receptor AV TV 4. Pulse VOLUME +/– para ajustar elvolumen. Para silenciar la salida, Pulse MUTE para silenciar la salida de audio. Pulse MUTE de nuevo para anular el silenciamiento. Existen más funciones variadas en la unidad. Consulte el “HTR-2067 Manual de Instrucciones” para obtener detalles sobre el uso eficaz de la unidad. Conexión de dispositivos externos distintos a los reproductores BD/DVD Conecte los cables del subwoofer ( ) al receptor AV. Cerciórese de conectar el subwoofer con la polaridad correcta—los terminales positivos (+) a los terminales positivos (+), y los terminales negativos (–) a los terminales negativos (–). 7 Es posible conectar a la unidad varios dispositivos, como reproductores de CD, etc. Cambio de los ajustes de entrada con una sola tecla (función SCENE) Esta unidad dispone de una función SCENE que le permite encenderla y cambiar las fuentes de entrada y los programas de campo sonoro con una tecla. Conectar la antena Su TV admite la función Audio Return Channel (canal de retorno de audio) • Si el TV admite ARC (Audio Return Channel), esta conexión no es necesaria. • Audio Return Channel necesita que se configure la función HDMI del receptor AV antes de usarlo. Para obtener más información, consulte “Información sobre HDMI” en el “HTR-2067 Manual de Instrucciones”. Receptor AV Subwoofer Para disfrutar de programas de campo sonoro Puede disfrutar de reproducción multicanal para casi todas las fuentes de sonido, utilizando diversos programas de campo sonoro almacenados en el chip y una amplia variedad de decodificadores de sonido. Para más detalles, consulte las instrucciones de funcionamiento completas en los manuales del usuario correspondientes. Altavoces frontales, surround • Corte el cable del altavoz incluido a una longitud adecuada para los altavoces frontales, central y surround y el subwoofer. Deberá unir seis cables. Pele unos 10 mm del aislamiento del extremo de cada cable y trence los filamentos descubiertos. • Conecte los cables del altavoz a los altavoces frontales ( ), a los altavoces surround ( ), al altavoz central ( ) y al subwoofer ( ). Cerciórese de conectar los altavoces y el subwoofer con la polaridad correcta—los terminales positivos (+) a los terminales positivos (+), y los terminales negativos (–) a los terminales negativos (–) correctos. 1. Encienda los componentes externos (TV, reproductor de BD, etc.) conectados aesta unidad. 2. Encienda esta unidad y seleccione la fuente de entrada utilizando Selector de entrada. Preparar los cables, los altavoces y el subwoofer Altavoz central Reproducción Procedimiento de reproducción básico Grabadoras y reproductores BD/DVD Receptor AV Los cuatro altavoces frontales y surround son idénticos, por lo que no importa el que utilice en cada ubicación. 4 Al altavoz central Conecte los cables del altavoz central ( ) y del altavoz surround ( ) al receptor AV. Cerciórese de conectar los altavoces con la polaridad correcta—los terminales positivos (+) a los terminales positivos (+), y los terminales negativos (–) a los terminales negativos (–). 6 Situar los altavoces Frontal izquierdo Al altavoz surround derecho Subwoofer (NS-SWP20) Altavoz frontal/surround (NS-B20) Altavoz central (NS-C20) Tacos antideslizantes Cable de altavoz Frontal derecho Receptor AV Panel trasero ● Conectar su grabadoras y reproductores BD/DVD, decodificador por cable/satélite x4 A una toma de CA Antena de FM Conecte la antena de FM ( ) al receptor AV, tal como se muestra. En los manuales del usuario encontrará más información acerca de cómo conectar la antena. ¡Es hora de disfrutar de su Yamaha Paquete Home Theater! Ahora, relájese y disfrute del excepcional sonido de su Yamaha Paquete Home Theater.
1 / 1

Yamaha YHT-1810 de handleiding

Categorie
Luidsprekersets
Type
de handleiding