Documenttranscriptie

English Deutsch Français DE 中文 EN FR ES PT 设置指南 IT セットアップガイド RU ZH JA 日本語 Setup Guide Installationsanleitung Guide de configuration Guía de configuración Guida alla configurazione Guia de Configuração Руководство по настройке Русский Italiano Português Español POWER AMPLIFIER  Contents Connections 3 Attaching Euroblock Plugs................................................................................................................................ 3 Connecting Speaker Cables............................................................................................................................. 3 Connecting Microphones or External Devices ................................................................................................. 4 Connecting Microphones ....................................................................................................................... 4 Connecting External Devices ................................................................................................................. 4 Using the Mono Sum Input ..................................................................................................................... 4 Connecting the PA2120 Power Amplifier.......................................................................................................... 5 Connecting a Control Panel .............................................................................................................................. 6 Functions Operated Via the Control Panel ............................................................................................. 6 Using the [REMOTE] Connector (Euroblock 3-pin) .......................................................................................... 7 Setup Mode (Advanced settings) 8 Setup Mode Operation Procedure.................................................................................................................... 8 Indication of Parameter Settings....................................................................................................................... 8 Operation Procedure ........................................................................................................................................ 9 Turning Off the Microphone Input High-Pass Filter ................................................................................ 9 Applying Compressor to the Microphone Input ..................................................................................... 9 Applying EQ (equalizer) to the Input Signal ......................................................................................... 10 Applying Echo/Reverb to the Input Signal............................................................................................ 11 Adjusting the Reverb Mix Level ............................................................................................................ 11 Adjusting the Ducker Sensitivity ........................................................................................................... 12 Regulating BGM Volume (Leveler) ....................................................................................................... 12 Setting the Chime Volume .................................................................................................................... 13 Adjusting the Line Out Volume by Using the [VOLUME] Knob ............................................................ 13 Microphone Feedback Suppressor ...................................................................................................... 14 Initializing the settings via connected controll panels (DCP Setup)..................................................... 14 List of DIP Switch Settings .............................................................................................................................. 15 [SETUP] DIP switches........................................................................................................................... 15 [SPEAKER A] and [SPEAKER B] DIP switches .................................................................................... 16 Appendix 17 List of Functions Operated Via the Control Panel ........................................................................................... 17 High-Impedance and Low-Impedance Connections ..................................................................................... 18 Multiple Speaker System Drive Capability............................................................................................ 18 Technical Specifications 163 This Setup Guide explains settings to make after installation, and connecting control panels and remote controller. • The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. 2 MA2120 Setup Guide  Connections Attaching Euroblock Plugs Example (Connection to the [REMOTE] connector) 1 Terminal screw Loosen Slotted screwdriver 2 Approx. 5 mm (approx. 0.2") 3 Tighten 4 Euroblock plug NOTE • You must use the supplied Euroblock plugs. If the plugs have been lost, please contact your Yamaha dealer. • Use the 6-pin Euroblock plugs when connecting to the [INPUT] connectors 1-6. • To prepare the cable for attachment to a Euroblock connector, strip the wire as shown in the illustration using stranded wire to make connections. With a Euroblock connection, stranded wires may be prone to breakage because of metal fatigue due to the weight of the cable or due to vibration. When rack mounting your device, use a lacing bar when possible to bundle and fasten the cables. • Do not tin (solder) the exposed end. 1 2 3 4 Loosen terminal screws. Insert cables. Securely tighten terminal screws. Insert the Euroblock plug into a terminal of this device. Connecting Speaker Cables The [SPEAKERS] output connectors on the rear panel are barrier strip type connectors. The connections are described below for two methods: using a spade lug and using a bare conductor. Caution • Ensure that load is not applied to the speaker cable. • This device uses a BTL (Balanced Transformer-Less) connection method for the amplifier output. As the amplifier output is sent to the positive and negative connectors, any contact with other terminals or the device chassis may lead to malfunction. NOTE Connect the cables so that the amplifier’s “+” and “-” symbols match those of the speaker. If they are reversed, the phase will be reversed and the sound will not be output correctly. When using a spade lug When using a bare conductor Loosen the screw, insert the spade lug all the way from below, and tighten the screw. Loosen the screw, wrap the conductor wire around the barrier strip terminal, and tighten the screw. Be sure that the bare wire does not touch the chassis. Speaker cable Wire should not touch the chassis. ≥3.2mm (≥ 0.13") ≥5.8mm (≥0.23") 15mm* (0.6") * Actual size MA2120 Setup Guide 3  Connections Connecting Microphones or External Devices Connect a microphone, BGM tuner, CD player or other portable audio player to an [INPUT] connector/jack using an appropriate cable when the device is powered off. After finishing all connections, connect the power cord to an AC outlet. Warning When connecting the power cord to an AC outlet, an input signal will turn on the power of this device by the auto-wake function. To avoid unexpected loud sounds, be sure to connect microphones and external devices with the power off status. RCA Euroblock MA2120 rear panel NOTE Refer to “Attaching Euroblock Plugs” for Euroblock plug installation. „ Connecting Microphones „ Using the Mono Sum Input Connect microphones to [INPUT] connectors 1 - 6 using a Euroblock plug. When using a microphone that requires phantom power (+24V), set the [GAIN] switch to “MIC(+24V)”. For microphones that do not require phantom power, set the [GAIN] switch to “MIC”. [INPUT 5] and [INPUT 6] are equipped with mono sum input. Each can be used for summing a line level stereo source, or two separate mono sources. The input signal is mixed directly to mono and output to the zone that was selected using the [ROUTE] switch for [INPUT] jack 5 and 6. Use of the [MONO SUM INPUT] jacks can allow a large number of external devices to be connected without the need for a separate mixer. However, note that when there is also input via Euroblock plugs for [INPUT] connector 5 or 6, the signal input from [MONO SUM INPUT] is mixed in with the signal from [INPUT] connector 5 or 6. Caution • Only switch the phantom power on/off when the [VOLUME A] and [VOLUME B] knobs are turned all the way down. • Keep the phantom power turned off when it is not required, or if you wish to connect a non-supporting device. • Do not connect or disconnect the cable while phantom power is left on. „ Connecting External Devices Use the following procedure to connect a line level external device. Use a Euroblock plug to connect via [INPUT] connectors 1 - 6. At this time, set the [GAIN] switch to “LINE”. If the external device has an extremely low output level, set the [GAIN] switch to “MIC” to improve the input gain. Use an RCA cable to connect to [INPUT] jacks 7 and 8. If the source is stereo and you are using zone A and zone B as stereo, set the [MODE] switch to “STEREO”. If you are using zone A and zone B separate from each other, set the [MODE] switch to “MONO” and use the [ROUTE] switch to select which zone receives the audio output. Use a mini-stereo plug to connect via the [AUX IN] jack on the front panel. The signal from the [AUX IN] jack is mixed into the same signal path as [INPUT] jack 8. 4 MA2120 Setup Guide  Connections Connecting the PA2120 Power Amplifier When using a large number of speakers that the MA2120 is not capable of handling alone, it is possible to connect a PA2120 power amplifier to provide extra capacity. To utilize this functionality, connect the [LINE OUT] jack of the MA2120 to the [INPUT] jack of the PA2120 using an RCA cable when all devices are powered off. If you wish to further expand capacity, it is possible to connect another PA2120 power amplifier. Simply connect the [THRU OUT] jacks of the PA2120 to the [INPUT] jacks of the additional PA2120 power amplifier. After finishing all connections, connect the power cord to an AC outlet. Warning When connecting the power cord to an AC outlet, an input signal will turn on the power of this device by the auto-wake function. To avoid unexpected loud sounds, be sure to connect microphones and external devices with the power off status. NOTE When lowering the output level with the [VOLUME] knobs or an external control panel, the Auto-wake function of PA2120 may not work properly because of an absence of input level. Be sure to set the output level to the PA2120 enough for the Auto-wake function to work properly. MA2120 rear panel PA2120 rear panel Further expanding PA2120 rear panel In setup mode, you can set whether the output level from the MA2120 [LINE OUT] jacks is linked with the output level from the MA2120 [SPEAKERS] terminals, or independently controlled. Set the [VOLUME] knobs of the PA2120 to maximum to adjust the level of PA2120 to the same level of MA2120. Linked operation when using the control panel can be set using the [SETUP] DIP switch. MA2120 Setup Guide 5  Connections Connecting a Control Panel Connecting Yamaha Digital Control Panel (DCP1V4S, DCP4S, DCP4V4S) to MA2120 enables you to control the volume, to switch inputs, etc. remotely. You can connect up to two control panels. The total length of the cables from the MA2120 to the last control panel must not exceed 800 meters in the case of 24AWG. NOTE When connecting control panels via DCH8, the total length of the cables to the final control panel must be less than 200m (according to DCH8 specifications). If you need a longer connection, we recommend not using the DCH8, but connecting the devices in a daisy-chain configuration. Precautions when connecting two control panels: • Connect them in a daisy-chain configuration. • Set the panel IDs separately. • Set the second control panel DIP switch 4 to ON. (termination setting) This setting is only for the second device when connecting two devices. • Ensure that the total Ethernet cable length does not exceed 800 meters in the case of 24AWG. Panel ID setting for control panel ON 1 2 3 4 Yamaha Digital Control Panel 0 1 2 3 4 5 6 7 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 Rear panel Rear panel ON ON 1 2 3 4 Sets the panel ID RJ-45 1 2 3 4 Set the DIP switch 4 to ON (termination setting). (The second control panel only if connecting two devices.) Sets the panel ID Ethernet straight cable (CAT5e or more; 800m or less (24 AWG)) MA2120 rear panel „ Functions Operated Via the Control Panel Several useful features of the MA2120 power amplifier can be utilized by connecting a control panel. Linked operation of output levels from [SPEAKERS] terminals and [LINE OUT] jacks Set the [SETUP] DIP switch on the rear panel to [SPEAKERS+LINE OUT] to allow the output level of the [SPEAKERS] and [LINE OUT] to be controlled together via the control panel. Input Signal On/Off Switching and Linked Operation The input channel of a device such as a microphone can be switched on and off by using the switch on the control panel. It is also possible to link on/off operation so that it triggers a chime, or mutes the input signal from [INPUT] jacks 7 and 8. 6 MA2120 Setup Guide  Connections Using the [REMOTE] Connector (Euroblock 3-pin) You can connect switches to the rear panel [REMOTE] connector, and use them to remotely mute/unmute outputs of all channels, or switch the power standby/on status. From the left, the [REMOTE] connector consists of M (mute all), S (standby), and G (ground) pins. The [REMOTE] connector uses a Euroblock plug. For details on how to connect Euroblock plugs, refer to “Attaching Euroblock Plugs.” Muting/unmuting all channels Turning mute on Turning mute off Switching the power standby/on status Switching the power to standby Turning the power on NOTE • When the device is put into standby mode via the [REMOTE] connector, it is not possible to turn the power back on by pressing the [z] button on the front panel, or by the auto-wake function with input signal detection. The power can only be turned on via the [REMOTE] connector. • When the device is put into mute mode via the [REMOTE] connector, the [z] button will flash in green. MA2120 Setup Guide 7  Setup Mode (Advanced settings) Advanced settings for MA2120 power amplifier can be configured by using the [SETUP] encoder and input level knobs 1 - 8. Input level knobs 1 - 8 [SETUP] encoder There are three types of setup modes that can be used to configure advanced settings. Operation and functionality for each setup mode type is shown as follows: • Input channel setup mode  Press and hold the [SETUP] encoder for at least one second. Microphone high-pass filter, microphone compressor, input EQ (TREBLE, BASS), reverb, ducker, leveler • Output zone setup mode  Press and hold the [SETUP] encoder and input level knob 1 simultaneously for at least one second. Chime volume, linked operation of [SPEAKERS] and [LINE OUT] • Other setup mode  Press and hold the [SETUP] encoder and input level knob 2 simultaneously for at least one second. Feedback suppressor, DCP setup Setup Mode Operation Procedure Advanced settings can be configured with the following procedure: Select the setup mode  [SETUP] encoder Input level knobs 1 and 2 Select the function  Select the channel Input level knobs 1 - 8 Input level knobs 1 - 8  Set parameters [SETUP] encoder Once each operation is carried out successfully, the corresponding indicator flashes three times at high speed. When selecting functions or channels, the indicator flashes slowly to indicate which functions or channels are able to be selected. While adjusting a parameter, you can press an input level knob so that the corresponding [INPUT SIG] indicator (showing the selected function) and [INPUT PEAK] indicator (showing the selected channel) both flash. Apply the parameter and return to channel selection  Return to function selection  Return to conventional operation [SETUP] encoder [SETUP] encoder [SETUP] encoder After you set the parameter, press the [SETUP] encoder to confirm the setting. At this time, press and hold the [SETUP] encoder for at least four seconds to reset the current parameter to the default setting. Once the parameter has been confirmed, the device mode returns to the channel selection. Press the [SETUP] encoder again to return to the function selection, and once more to return to the regular mode. Indication of Parameter Settings In setup mode, the current settings are indicated by the three indicators above the [SETUP] encoder. The indicators can turn on or flash to show the on/off state or the currently set value. In addition, depending on the parameter value, the flashing behavior may differ. For example, when the delay time of echo set is increased, the lighting time during flashing becomes longer. In this guide, the behavior of the indicators is shown as follows. : Lights continuously : Flashes : Off 8 MA2120 Setup Guide  Setup Mode (Advanced settings) Operation Procedure „ Turning Off the Microphone Input High-Pass Filter The microphone input high-pass filter (Cut-off frequency: 120Hz) is turned on by default. This can reduce wind or popping noise when using a microphone. The high-pass filter is enabled for the input channel when the [GAIN] switch is set to either “MIC(+24V)” or “MIC”. NOTE The high-pass filter is also applied to the [MONO SUM INPUT] when the [GAIN] switch for INPUT 5 and 6 is set to either “MIC(+24V)” or “MIC”. 2 3 1 Press and hold the [SETUP] encoder for at least one second. 2 3 Press input level knob 1. 4 Turn the [SETUP] encoder to switch between on and off. 1, 4, 5 Press input level knobs 1 - 6 to select to which input channel you would like to apply the highpass filter. Off: On: 5 (Default setting) Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). „ Applying Compressor to the Microphone Input The microphone input can be run through a compressor that appropriately compresses the input signal, and adjusts the output level automatically. The compression level is shown as one of seven levels with higher values indicating a higher level of compression. The compressor is enabled for the input channel when the [GAIN] switch is set to either “MIC(+24V)” or “MIC”. NOTE The compressor is applied to the [MONO SUM INPUT] when the [GAIN] switch for INPUT 5 and 6 is set to either “MIC(+24V)” or “MIC”. 2 3 1 Press and hold the [SETUP] encoder for at least one second. 2 3 Press input level knob 2. 4 Turn the [SETUP] encoder to adjust the level of compression. 1, 4, 5 Press input level knobs 1 - 6 to select to which input channel you would like to apply the compressor. The parameter value changes with each click of the encoder. Off: (Default setting) 1: 2 and 3: 4: 5 and 6: 7: 5 Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). MA2120 Setup Guide 9  Setup Mode (Advanced settings) „ Applying EQ (equalizer) to the Input Signal A two-band EQ (TREBLE and BASS) can be applied to the input signal to adjust the sound quality. The EQ range is ±10dB and can be set in intervals of 1dB. 2 3 1, 4, 5 1 Press and hold the [SETUP] encoder for at least one second. 2 Press input level knob 3 (BASS), or input level knob 4 (TREBLE). 3 Press input level knobs 1 - 8 to select to which input channel you would like to apply the EQ. 4 Turn the [SETUP] encoder to adjust the level of EQ. The parameter value changes with each click of the encoder. -10dB: -9 to -6dB: -5dB: -4 to -1dB: 0dB: (Default setting) +1 to +4dB: +5dB: +6 to +9dB: +10dB: NOTE If the set EQ value for [INPUT 7] and [INPUT 8] exceeds +5dB, the enhancer function starts and harmonic overtones are added. 5 Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). 10 MA2120 Setup Guide  Setup Mode (Advanced settings) „ Applying Echo/Reverb to the Input Signal Echo/Reverb can be applied to the INPUT 1 and INPUT 3 input signals to add extra sound reverberation. The “Echo” type, which allows for the adjustment of reverberation time, or three “Reverb” types are available. 3 2 1 Press and hold the [SETUP] encoder for at least one second. 2 3 Press input level knob 5. 4 Turn the [SETUP] encoder to select the echo/ reverb preset. 1, 4, 5 Press input level knob 1, or input level knob 3 to select to which input channel you would like to apply the echo/reverb. The parameter value changes with each click of the encoder. 5 Off: (Default setting) Echo: (As the echo time is increased, the center indicator flash time becomes longer. The maximum value is indicated by a flash that has a 740ms light-on time.) Reverb: (Right indicator flashes for type A and type B. It stays on for type C.) Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). „ Adjusting the Reverb Mix Level You can adjust the mix level of the reverb that is applied to the [INPUT 1] and [INPUT 3] input signals. The percentage of reverb applied to the original signal can be set from 0% to 100%. There are ten possible levels with intervals of 10%. 3 2 1 Press and hold the [SETUP] encoder for at least one second. 2 3 Press input level knob 6. 4 Turn the [SETUP] encoder to adjust the reverb mix level. 1, 4, 5 Press input level knob 1, or input level knob 3 to select to which input channel you would like to adjust reverb mix level. The parameter value changes with each click of the encoder. 0%: 10%: 20% to 40%: 50%: (Default setting) 60% to 90%: 100%: 5 Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). MA2120 Setup Guide 11  Setup Mode (Advanced settings) „ Adjusting the Ducker Sensitivity You can adjust the sensitivity of the ducker function. When there is an input signal to [INPUT 1] or [INPUT 3], this function can mute the microphone input for channels outside that particular output zone, or lower their line input volume by 24dB. The ducker input sensitivity can be set to “Low”, “Mid”, or “High”. NOTE The ducker function can be turned on or off by switching [SETUP] DIP switches 7 and 8 when the device is powered off or in standby mode. For more information, refer to “Controls and Functions” of the owner's manual, or “List of DIP Switch Settings” on page 15. 3 2 1 Press and hold the [SETUP] encoder for at least one second. 2 3 Press input level knob 7. 4 Turn the [SETUP] encoder to adjust the ducker sensitivity. 1, 4, 5 Press input level knob 1, or input level knob 3 to select to which input channel you would like to adjust the sensitivity of ducker function. The parameter value changes with each click of the encoder. Low: Mid: (Default setting) High: 5 Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). „ Regulating BGM Volume (Leveler) You can select the target level for the leveler function. This function adjusts the volume to an almost constant range when there are [INPUT 7]/[INPUT 8] input signals that have a significant variation in volume. The leveler function can be used to adjust a signal with a range of up to ±6dB. The target level can be set to “Off,” “Low” or “Normal.” NOTE Channels with the leveler function enabled have an output signal delay of approximately 20ms due to the required arithmetic processing. 3 1 Press and hold the [SETUP] encoder for at least one second. 2 3 Press input level knob 8. 4 Turn the [SETUP] encoder to select the target level. 2 1, 4, 5 Press input level knob 7, or input level knob 8 to select to which input channel you would like to apply the leveler function. Off: (Default setting) Low: Normal: 5 Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). 12 MA2120 Setup Guide  Setup Mode (Advanced settings) „ Setting the Chime Volume You can set the volume of the chime that is emitted when the microphone input is turned on or off via by the control panel switch. The volume can be set to “Mute”, “-12dB”, or “-6dB”. You can set different volumes for each zone. 1, 2 3 1, 4, 5 1 Press and hold the [SETUP] encoder and input level knob 1 simultaneously for at least one second. 2 3 Press input level knob 1. 4 Turn the [SETUP] encoder to set the volume. Press input level knob 1 (Zone A), or input level knob 2 (Zone B) to select to which output channel you would like to set the chime volume. The parameter value changes with each click of the encoder. Off: -12dB: -6dB: (Default setting) 0dB: 5 Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). „ Adjusting the Line Out Volume by Using the [VOLUME] Knob You can turn the linked operation function for [SPEAKERS] and [LINE OUT] on or off. This function allows the output signal level from the [LINE OUT] jack to be simultaneously adjusted when the [VOLUME A] and [VOLUME B] knobs are operated. NOTICE When switching this parameter, set the volume of the device connected to the [LINE OUT] connector to minimum. 3 2 1 4, 5 1 Press and hold the [SETUP] encoder and input level knob 1 simultaneously for at least one second. 2 3 Press input level knob 2. 4 Turn the [SETUP] encoder to turn the linked operation function for [SPEAKERS] and [LINE OUT] on or off. Press input level knob 1 (Zone A), or input level knob 2 (Zone B) to select to which output channel you would like to adjust the line out volume by using the [VOLUME] knob. Off: (Default setting) On: 5 Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). MA2120 Setup Guide 13  Setup Mode (Advanced settings) „ Microphone Feedback Suppressor You can turn the feedback suppressor function on or off. This function automatically suppresses microphone feedback when detected. The feedback suppressor is enabled for the input channel when the [GAIN] switch is set to either “MIC(+24V)” or “MIC”. NOTE The feedback suppressor is applied to the [MONO SUM INPUT] when the [GAIN] switch for INPUT 5 and 6 is set to either “MIC(+24V)” or “MIC”. 32 1 4, 5 1 Press and hold the [SETUP] encoder and input level knob 2 simultaneously for at least one second. 2 3 Press input level knob 1. 4 Turn the [SETUP] encoder to switch between the feedback suppressor on and off. Press input level knobs 1 - 6 to select for which input channels you would like to use the feedback suppressor. Off: On: 5 (Default setting) Press the [SETUP] encoder to apply the setting. The status is back to the channel select (Step 3). „ Initializing the settings via connected controll panels (DCP Setup) When turning on the power, this sets whether resuming the settings of connected control panels or initializing. 32 1 4, 5 1 Press and hold the [SETUP] encoder and input level knob 2 simultaneously for at least one second. 2 3 4 Press input level knob 2. Press input level knob 1. Turn the [SETUP] encoder to switch between resuming the previous settings or initializing the settings when turning on the power. Resume: (Default setting) Initialize: 5 Press the [SETUP] encoder to apply the setting. The status returns to Step 3. 14 MA2120 Setup Guide  Setup Mode (Advanced settings) List of DIP Switch Settings DIP switch functions are also listed in the “Controls and Functions” section of the owner's manual. Only operate DIP switches when the device is powered off or in standby mode. The setting change will be applied after carrying out a power cycle by pressing the [z] button on the front panel. „ [SETUP] DIP switches DIP switch 1/2: Panel lock Set knobs and controls to be locked on the panel. 1 2 Setting Panel lock off (All controls are enabled) Locks the [SETUP] knob Locks controls other than [VOLUME] knobs Panel lock on (All controls are disabled) DIP switches 3/4: Auto-wake Enable the function where the device automatically turns on from standby mode upon detection of an input signal. 3 4 Setting Auto-wake function on Auto-wake function on. Only when the system is switched from AC off to standby mode due to insertion of the AC plug, or put into standby mode by the auto-standby function. Auto-wake function off NOTE The auto-wake function is completely disabled if the device has been put into standby mode through operation via the [REMOTE] connector. DIP switch 5: A - B volume link Sets whether SPEAKER A and SPEAKER B volume is linked. When linked, the volume for both speakers can be controlled with the [VOLUME A] knob. 5 Setting Link off (SPEAKER A and SPEAKER B volume levels are independently controlled) Link on (SPEAKER A and SPEAKER B volume levels are both controlled via the [VOLUME A] knob) NOTE If you turn on “A - B volume link” when the function to allow control of the line out volume A and B by the [VOLUME] knob is enabled in setup mode, LINE OUT A and B are also linked. DIP switch 6: DCP volume link Sets whether the [SPEAKERS] and [LINE OUT] jack output levels are linked, when changing the volume via the DCP. 6 Setting Link off ([SPEAKERS] and [LINE OUT] jack volume levels are controlled separately) Link on ([SPEAKERS] and [LINE OUT] jack output is controlled together) NOTE When the link function is on, you can control the volume by using both of [SPEAKER] and [LINE OUT] on the control panel. MA2120 Setup Guide 15  Setup Mode (Advanced settings) DIP switches 7/8: Ducker Configure the settings for the Ducker function. This can mute the microphone input of other channels, and lower the volume of line input when signals are input to [INPUT 1] or [INPUT 3]. 7 8 Setting Ducker off Ducker on when signals are input to [INPUT 1]. Ducker on when signals are input to [INPUT 3]. Ducker on when signals are input to [INPUT 1] or [INPUT 3]. If signals are input to both of them, [INPUT 1] is given precedence. „ [SPEAKER A] and [SPEAKER B] DIP switches DIP switches 1, 2, and 3: Amplifier mode setup DIP switches 1, 2, and 3: Amplifier mode setup NOTICE If the DIP switch settings do not match the actual speaker impedance or input power rating, the device may have poor performance, and it may even lead to malfunction or sound dropout. Always ensure that appropriate settings are chosen. 1 2 3 Setting Amplifier output 120W, High-impedance 100V Amplifier output 120W, High-impedance 70V Amplifier output 200W, High-impedance 100V, Output only from [SPEAKERS] output terminal A Amplifier output 200W, High-impedance 70V, Output only from [SPEAKERS] output terminal A Amplifier output 100W, Low-impedance 8Ω or more Amplifier output 120W, Low-impedance from 4Ω to less than 8Ω Amplifier output 100W, Low-impedance from 3Ω to less than 4Ω Output muted DIP switches 4, 5, and 6: Speaker EQ Sets the speaker EQ that corrects the output signal to match the type of speakers that are connected. 4 5 6 Setting Off High pass filter 150Hz Low pass filter 150Hz Low pass filter 200Hz Frequency correction tailored for Yamaha VXS series speakers Frequency correction tailored for the Yamaha VXS10S/VXS10ST subwoofer (45-150Hz) Frequency correction tailored for Yamaha VXC series speakers 16 MA2120 Setup Guide  Appendix List of Functions Operated Via the Control Panel DCP1V4S Panel ID Encoder 0, 1 Volume control 2, 3 Volume control [INPUT 1] on/off Chime on 4, 5 Volume control 6, 7 Switch 1 Switch 2 Switch 3 Switch 4 Encoder operation target: SPEAKERS A Encoder operation target: SPEAKERS B [INPUT 3] on/off Chime on Encoder operation target: SPEAKERS A Encoder operation target: SPEAKERS B [INPUT 1] on/off Chime on Mute [INPUT] 7 and 8 [INPUT 3] on/off Chime on Mute [INPUT] 7 and 8 Encoder operation target: SPEAKERS A Encoder operation target: SPEAKERS B Volume control Encoder operation target: LINE OUT A Encoder operation target: LINE OUT B Encoder operation target: SPEAKERS A Encoder operation target: SPEAKERS B Panel ID Switch 1 Switch 2 Switch 3 Switch 4 0, 1 Volume up: SPEAKERS A Volume down: SPEAKERS A Volume up: SPEAKERS B Volume down: SPEAKERS B 2, 3 Volume up: LINE OUT A Volume down: LINE OUT A Volume up: LINE OUT B Volume down: LINE OUT B 4, 5 [INPUT 1] on/off Chime on [INPUT 3] on/off Chime on 6, 7 [INPUT 1] on/off Chime on Mute [INPUT] 7 and 8 [INPUT 3] on/off Chime on Mute [INPUT] 7 and 8 DCP4S DCP4V4S Panel ID Encoder 1 Encoder 2 Encoder 3 Encoder 4 0, 1 Volume control LINE OUT A Volume control LINE OUT B Volume control SPEAKERS A Volume control SPEAKERS B 2 Volume control INPUT 1 Volume control INPUT 2 Volume control INPUT 3 Volume control INPUT 4 3 Volume control INPUT 5 Volume control INPUT 6 Volume control INPUT 7 Volume control INPUT 8 4, 5 Volume control INPUT 1 Volume control INPUT 3 Volume control SPEAKERS A Volume control SPEAKERS B 6, 7 Volume control INPUT 7 Volume control INPUT 8 Volume control SPEAKERS A Volume control SPEAKERS B Panel ID Switch 1 Switch 2 Switch 3 Switch 4 2 [INPUT 1] on/off [INPUT 2] on/off [INPUT 3] on/off [INPUT 4] on/off 3 [INPUT 5] on/off [INPUT 6] on/off [INPUT 7] on/off [INPUT 8] on/off 4, 5 [INPUT 1] on/off Chime on Mute [INPUT] 7 and 8 [INPUT 3] on/off Chime on Mute [INPUT] 7 and 8 0, 1 6, 7 MA2120 Setup Guide 17  Appendix High-Impedance and Low-Impedance Connections For a high-impedance connection, a speaker transformer that raises the impedance to several hundred or thousand ohms is added to the speaker system. This allows the speaker system to be effectively driven with much lower current than is required for a low-impedance connection. Therefore, a large number of speaker systems can be connected. Even over long distances, there is very little transmission loss due to the cable resistance being negligible in relation to the impedance of the speaker system. High-impedance speaker connections usually operate at a specific maximum power amplifier voltage of 100 or 70 volts. The more orthodox low-impedance connection does not use a speaker transformer. The speaker systems are directly connected to the power amplifier with a rated impedance generally around 4 - 16 ohms. For short distances over which cable resistance is insignificant, low-impedance connections deliver a sound quality that is superior to high-impedance connections. The differences between connection methods are explained as follows. „ Multiple Speaker System Drive Capability High-Impedance Connections As long as the total nominal power input rating for all speakers is within the power output capability of the amplifier, any number of speaker systems can be connected in parallel. The power input rating is determined by the speaker systems and speaker transformers used. It is also possible to connect speaker systems that have different input power ratings. In the case of speaker systems that are capable of changing their input power rating (Yamaha VXC and VXS series, etc.), this can be utilized to vary the volume of each speaker. Speaker transformer 70V/100V 10W 10W 10W 10W 10W Low-Impedance Connections When connecting multiple low-impedance speaker systems to a single channel, the following methods are possible. Parallel Connection When multiple speaker systems having the same impedance are connected in parallel, the total impedance becomes the individual speaker system impedance divided by the number of systems connected. 4Ω Cannot be connected 8Ω 8Ω 8Ω Total impedance = 4Ω Serial Connection When connected in series, the total impedance is simply the sum of the impedances of the speaker systems connected. However, if one speaker system happens to fail, the electrical signal will not be passed on and subsequent speaker systems will be affected. 4Ω Interruption 18 MA2120 Setup Guide 4Ω Failure No sound Total impedance = 8Ω  Technical Specifications Specification Outputs （SPEAKER OUT) Output Power 20msec Burst (THD+N=1%) AMP MODE = 3Ω 100W x 2ch AMP MODE = 4Ω 120W x 2ch AMP MODE = 8Ω 100W x 2ch AMP MODE = 70V/120W 120W x 2ch AMP MODE = 100V/120W 120W x 2ch AMP MODE = 70V/200W 200W x 1ch AMP MODE = 100V/200W Terminal 200W x 1ch 7.62mm BARRIER STRIP 4pin Outputs (LINE OUT) LINE OUT Actual source impedance For use with nominal Output Level Nominal Terminal 600Ω 10kΩ Lines -10dBV (316mV) MONO RCA PIN x2, unbalanced Inputs MIC IN (INPUT 1-6) Input Level INPUT 1-6, Euro, balanced Sensitivity -56dBu (1.23mV) Nominal -36dBu (12.3mV) Max before clip -8dBu (0.309V) LINE IN (INPUT 1-8) Input Level INPUT 1-6, Euro, balanced Input Level INPUT 5-8, RCA, unbalanced Input Level INPUT 8, ST mini phone, unbalanced Sensitivity -24dBu (48.9mV) Nominal -4dBu (0.489V) Max before clip +24dBu (12.3V) Sensitivity -30dBV (31.6mV) Nominal -10dBV (316mV) Max before clip +10dBV (3.16V) Sensitivity -30dBV (31.6mV) Nominal -10dBV (316mV) Max before clip +10dBV (3.16V) Terminal MIC/LINE IN INPUT 1-6 3.5mm Euro Block 6pin x3 balanced LINE IN INPUT 5-6 MONO RCA PIN x4 unbalanced INPUT 7-8 STEREO RCA PIN x2 unbalanced INPUT 8 (Front Panel) 3.5mm STEREO mini phone x1 unbalanced MA2120 Setup Guide 163  Technical Specifications Electrical Characteristics Class D Amplifier type (Output circuitry) THD+N Frequency Response LINE IN to SPEAKER OUT, Half power@1kHz AMP MODE = 3Ω, 4Ω, 8Ω ≤ 0.2% LINE IN to SPEAKER OUT, Half power@1kHz AMP MODE = 70V, 100V/120W ≤ 0.2% LINE IN to SPEAKER OUT, Half power@1kHz AMP MODE = 70V, 100V/200W ≤ 0.2% LINE IN to SPEAKER OUT, 50Hz to 20kHz@1W AMP MODE = 3Ω, 4Ω, 8Ω 0dB, -3.0dB, +1.0dB LINE IN to SPEAKER OUT, 90Hz to 20kHz@1W AMP MODE = 70V, 100V/120W 0dB, -3.0dB, +1.0dB LINE IN to SPEAKER OUT, 90Hz to 20kHz@1W AMP MODE = 70V, 100V/200W 0dB, -3.0dB, +1.0dB LINE IN to LINE OUT, 20Hz-20kHz 0dB, -2.5dB, +1.0dB Crosstalk MIC/LINE IN to other MIC/LINE IN Load Protection POWER/STANDBY SW on/off Output Voltage Protection Amplifier Protection Power Supply shutdown Thermal Limit output → Mute → Shutdown Mute the output (with automatic restoration) Integrated Power Limit Thermal Connectors Power supply shutdown Over current Limit power → Power supply shutdown Conventional cooling, bottom to up airflow Front Panel POWER/STANDBY SW, INPUT volume x 8, SETUP encoder x 1 OUTPUT volume x 2, BASS EQ volume x 2, TREBLE EQ volume x 2 Rear Panel SETUP DIP SW x1, SPEAKER A/B DIP SW x2, ROUTE SW x4, GAIN SW x3, MODE SW x1 Analog In (MIC/LINE) Analog In (LINE) Analog Out Speakers Remote Indicators AC Power Requirement 164 MA2120 Setup Guide Compress output Power supply shutdown Over voltage Cooling Controls Compress output voltage when needed DC-fault Over current Power Supply Protection ≤ -70dB Mute the output 3.5mm Euro Block 6pin x3 (Rear) MONO RCA PIN x4 (Rear), STEREO RCA PIN x2 (Rear), 3.5mm STEREO mini phone x1 (Front) MONO RCA PIN x2 (Rear/LINE OUT) 7.62mm BARRIER STRIP 4pin x1 (Rear) RJ45 x1 (Rear/DCP), 3.5mm Euro Block 3pin x1 (Rear/REMOTE) POWER x1 (Green/Orange), INPUT SIGNAL x8 (Green), INPUT PEAK x8 (Red), SETUP x3 (Green), OUTPUT SIGNAL x2 (Green), OUTPUT LIMIT x2 (Red) 100V, 120V, 230V-240V 50Hz/60Hz (*1) *1 It has confirmed that it is working with ±10% of the voltage of the rated supply voltage.  Technical Specifications Power Consumption Standby, default setting AMP MODE = All ≤ 1W Idle AMP MODE = 3Ω, 4Ω, 8Ω 15W Idle AMP MODE = 70V, 100V 20W 1/8 Output, Pink noise AMP MODE = 4Ω 60W 1/8 Output, Pink noise AMP MODE = 70V/120W 60W ENERGY STAR • It automatically enters into standby mode when no input signal is detected for 25 minutes in order to save power while not in use. • Amplifier efficiency: 44% and more. • Less than 1W in standby. General Specifications Precautions for rack mounting Operating temperature Storage temperature Dimensions (W x H x D, not including knob) Net Weight Rack mountable (Leave more than 1U of spaces between this unit and others.) 0 ℃ to +40 ℃ -20 ℃ to +60 ℃ 480 x 44 x 351 mm 18.90 x 1.73 x 13.82 inch 4.9kg Included Accessories AC power cord (2.0m) x1, 3.5mm Euroblock plug (6pin) x3, 3.5mm Euroblock plug (3pin) x1, Owner's Manual x1, Setup Guide x1 Optional accessories Digital Control Panel (DCP1V4S-US/EU, DCP4V4S-US/EU, DCP4S-US/EU） MA2120 Setup Guide 165  Technical Specifications Dimensions (unit: mm) 379.4 361.8 430 166 MA2120 Setup Guide 45.1 44 480  L/R R L R L 㻳 㻙 㻗 㻳 㻙 㻗 REMOTE DCP INPUT 8 INPUT 7 INPUT 6 INPUT 5 INPUT 4 INPUT 3 INPUT 2 INPUT 1 㻳 㻙 㻗 㻳 㻙 㻗 㻳 㻙 㻗 㻳 㻙 㻗 STANDBY LOGIC R L 㻗 HA 㻙 㻗 HA 㻙 㻗 HA 㻙 㻗 HA 㻙 PHANTOM +24V LINE LINE MIC LINE MIC PHANTOM +24V 㻗 HA 㻙 MIC PHANTOM +24V 㻗 HA 㻙 STEREO SUM STEREO BA SUM SUM INPUT VOLUME INPUT VOLUME INPUT VOLUME INPUT VOLUME INPUT VOLUME INPUT VOLUME INPUT VOLUME INPUT VOLUME ADC ADC ADC ADC ADC ADC ADC ADC CH8 SIGNAL/PEAK CH7 SIGNAL/PEAK CH6 SIGNAL/PEAK CH5 SIGNAL/PEAK CH4 SIGNAL/PEAK CH3 SIGNAL/PEAK CH2 SIGNAL/PEAK CH1 LINE MIC LINE MIC HPF 120Hz HPF 120Hz NOISE GATE NOISE GATE LINE MIC LINE MIC LINE MIC LINE MIC CHIME MONO STEREO MONO STEREO HPF 120Hz HPF 120Hz HPF 120Hz HPF 120Hz GAIN CONTROL LEVELER LEVELER NOISE GATE NOISE GATE NOISE GATE NOISE GATE DUCKER TRIGGER SOURCE CH1, CH3 (PRIORITY CH1 > CH3) DSP PROCESS SIGNAL/PEAK TREBLE BASS INPUT EQ ENHANCER TREBLE BASS INPUT EQ ENHANCER COMP COMP COMP COMP COMP COMP FEEDBACK SUPPRESSOR FEEDBACK SUPPRESSOR FEEDBACK SUPPRESSOR FEEDBACK SUPPRESSOR FEEDBACK SUPPRESSOR FEEDBACK SUPPRESSOR TREBLE BASS INPUT EQ TREBLE BASS INPUT EQ TREBLE BASS INPUT EQ TREBLE BASS INPUT EQ TREBLE BASS INPUT EQ TREBLE BASS INPUT EQ ECHO REVERB ECHO REVERB DCP VOLUME DCP VOLUME DCP VOLUME DCP VOLUME DCP VOLUME DCP VOLUME DCP VOLUME DCP VOLUME BUS A BUS B DUCKER MUTE HPF 40Hz 80Hz HPF 40Hz 80Hz Lo-Z Hi-Z Lo-Z Hi-Z DCP SPEAKER+LINE OUT VOLUME INDIVIDUAL A-B VOLUME OFF LINK ON DCP VOLUME DCP VOLUME DCP VOLUME DCP VOLUME OFF HPF150Hz LPF 150Hz LPF 200Hz SURFACE CEILING VXS10S(T) SPEAKER EQ OFF HPF150Hz LPF 150Hz LPF 200Hz SURFACE CEILING VXS10S(T) SPEAKER EQ TREBLE BASS OUTPUT EQ TREBLE BASS OUTPUT EQ LIMITER LIMIT LIMITER LIMIT TEMP OUTPUT VOLTAGE LIMITER SIGNAL SIGNAL INTEGRAL OUTPUT POWER AMP PROTECTION LOGIC LINE VOLUME SPEAKER-LINE VOLUME LINK LINE VOLUME SPEAKER-LINE VOLUME LINK OUTPUT VOLUME B OUTPUT VOLUME A BA BA 100V 70V 8䃈 4䃈 3䃈 OUTPUT FORMAT SELECTION 100V 70V 8䃈 4䃈 3䃈 OUTPUT FORMAT SELECTION DC-FAULT POWER SUPPLY OUTPUT CURRENT AMP AMP PROTECTION HARDWARE DAC DAC DAC DAC ENABLE AMP ENABLE AMP SPEAKERS LINE OUT B LINE OUT A B A [ AMP MODE ] 120W/100V 120W/70V 100W/8䃈 120W/4䃈 100W/3䃈 DISABLE AMP ENABLE AMP SPEAKERS B: No output A [ AMP MODE ] 200W/100V 200W/70V Technical Specifications Block Diagram MA2120 Setup Guide 167  168 MA2120 Setup Guide G%X G%X G%X G%X G%X G%X G%X G%X 6WHUHRPLQL 5&$6WHUHR 5&$0RQR[ 㻳 (XUR0,&G%X (XUR0,&G%X (XUR/,1(G%X (XUR/,1(G%X (XUR0,&G%X 0,&/,1( 1RUPDO3KDVH 㻴㻭 0,&/,1( 㻙 㻗 6HQVLWLYLW\OHYHO 1RPLQDOOHYHO 5&$6WHUHRPLQL G%9 G%X 1RQFOLSOHYHO 1RUPDO3KDVH *DLQG% (XUR/,1(G%X ^1RPL G%9 G%X` ,1387 ^1RPL G%9 G%X` ,1387 ^1RPL G%9 G%X` ^1RPLG%X` ,1387 㻗 㻙 㻴㻭 㻙 㻗 *DLQG% PP(852%/2&.SLQ 㻳 㻗 㻙 PP(852%/2&.SLQ ^1RPLG%X` ,1387 㻿㼁㻹 ,QYHUWHG 3KDVH G%X G%X ,QYHUWHG3KDVH ,QYHUWHG3KDVH 9RO 0D[ >9RO*DLQG%@ 9RO1RPLQDOSRVLWLRQLVG% IURP9RO0D[SRVLWLRQ 9RO 1RPLQDO >9RO*DLQG%@ $'&1RP G%X +HDG5RRP0DUJLQ G% $'&G%)6 G%X '63 1RUPDO 3KDVH 1RUPDO 3KDVH 1RUPDO 3KDVH 1RUPDO 3KDVH 㻰㻿㻼           'LJLWDO G%)6  G%)6 28738792/80( 28738792/80( $ % 'LJLWDO G%)6 G%)6  㻰㼕㼓㼕㼠㼍㼘 $'& $'& $'& $'& 㻭㼚㼍㼘㼛㼓 ,QYHUWHG3KDVH ,138792/80( (92/ ,138792/80( (92/ ,138792/80( (92/ +HDG5RRP0DUJLQ G% (92/ G%X *DLQG% ,QYHUWHG 3KDVH 㻿㼁㻹 *DLQG% (852*DLQG% 5&$*DLQG% 㻿㼁㻹 ,QYHUWHG 3KDVH ,138792/80( (92/ 1RUPDO3KDVH 㻰㼕㼓㼕㼠㼍㼘 ,19 㼕㼚㼢㼑㼞㼠㼑㼐 㼜㼔㼍㼟㼑 ,19 㼕㼚㼢㼑㼞㼠㼑㼐 㼜㼔㼍㼟㼑 ,19 㼕㼚㼢㼑㼞㼠㼑㼐 㼜㼔㼍㼟㼑 ,19 㼕㼚㼢㼑㼞㼠㼑㼐 㼜㼔㼍㼟㼑 㻸㻼㻲 㻙 㻗 㻸㻼㻲 㻸㻼㻲 㻳㻭㻵㻺㻦㻗㻥㻚㻞㼐㻮 㻙 㻗 㻳㻭㻵㻺㻦㻗㻥㻚㻞㼐㻮 㻙 1RUPDO 3KDVH 㻙 㻸㻼㻲 +HDG5RRP0DUJLQG% 7R/,1(287 㻔㻙㻥㻚㻟㼐㻮㼡㻕 㻔㻗㻤㻚㻣㼐㻮㼡㻕 $77 $77 ,QYHUWHG3KDVH ,QYHUWHG3KDVH 1RUPDO 3KDVH 1RUPDO 3KDVH 㻔㻙㻜㻚㻝㼐㻮㼡㻕 G%X ,QYHUWHG 㻳㻭㻵㻺㻦㻗㻥㻚㻞㼐㻮 3KDVH 㻗 1RUPDO 3KDVH ,QYHUWHG 㻳㻭㻵㻺㻦㻗㻥㻚㻞㼐㻮 3KDVH 㻗 ,QYHUWHG 3KDVH 1RUPDO 3KDVH ,QYHUWHG 3KDVH 1RUPDO 3KDVH '$&G%)6 G%X 287 287 287 287 287 287 287 287 7R63($.(5287 +HDG5RRP0DUJLQG% 㻭㼚㼍㼘㼛㼓 '$& '$& '$& '$& '$& '$& '$& '$& 㻭㻹㻼㻌㻹㼛㼐㼑 㻝㻜㻜㼂 㻣㻜㼂 㻤䃈 㻠䃈 㻟䃈 ,19 ,19 㻳㻭㻵㻺㻦㻙㻣㻚㻣㼐㻮 㻔㻗㻢㻚㻥㼐㻮㼡㻕 㻔㻗㻠㻚㻣㼐㻮㼡㻕 㻔㻗㻞㻚㻣㼐㻮㼡㻕 㻔㻗㻝㻠㻚㻥㼐㻮㼡㻕 㻔㻗㻝㻣㻚㻥㼐㻮㼡㻕 1RUPDO3KDVH 1RUPDO3KDVH ,QYHUWHG 3KDVH 㻳㻭㻵㻺㻦㻙㻣㻚㻣㼐㻮 ,19 㻳㻭㻵㻺㻦㻜㼐㻮 ,19 㻳㻭㻵㻺㻦㻜㼐㻮 㻭㼀㼀 㻜㼐㻮 㻙㻟㻚㻜㼐㻮 㻙㻝㻝㻚㻜㼐㻮 㻙㻝㻟㻚㻞㼐㻮 㻙㻝㻡㻚㻞㼐㻮 ,QYHUWHG 3KDVH 3$03 QRUPDO 3$03 LQYHUWHG ȐG%X ȐG%X ȐG%X 9G%X 9G%X ,QYHUWHG 3KDVH 1RUPDO 3KDVH ,QYHUWHG 3KDVH 1RUPDO 3KDVH /,1(287G%9 G%X 㻳㻭㻵㻺㻦㻗㻞㻠㻚㻟㼐㻮 3$03 QRUPDO 3$03 LQYHUWHG 㻻㼁㼀㻼㼁㼀 㻠㻞㻚㻞㼐㻮㼡 㻟㻥㻚㻞㼐㻮㼡 㻟㻝㻚㻞㼐㻮㼡 㻞㻥㻚㻜㼐㻮㼡 㻞㻣㻚㻜㼐㻮㼡 G%X G%X G%X G%X G%X G%X G%X G%X 㻸㻵㻺㻱㻌㻻㼁㼀䚷㻮 ^1RPLG%9 G%X` 㻸㻵㻺㻱㻌㻻㼁㼀䚷㻭 䠇 㻿㻼㻱㻭㻷㻱㻾㻌㻻㼁㼀 䠉 㻮 㻭㻹㻼㻌㻹㼛㼐㼑 㻝㻜㻜㼂 㻣㻜㼂 㻤䃈 㻠䃈 㻟䃈 䠇 㻿㻼㻱㻭㻷㻱㻾㻌㻻㼁㼀 䠉 㻭 Technical Specifications Level Diagram  Technical Specifications Current Draw 1/8 power is typical of program material with occasional clipping. Refer to these figures for most applications. 1/3 power represents program material with extremely heavy clipping Test signal: Pink Noise, bandwidth limited from 22Hz to 22kHz 1W = 0.860kcal/h, 1BTU = 0.252kcal Note that Line Voltage [V] x Line Current [A] = [VA], not equals to [W] 230V/50Hz Idle 1/8 output power 1/3 output power Sleep AMP-MODE：3Ω/4Ω/8Ω AMP-MODE : 120W-70V/100V AMP-MODE：200W-70V/100V AMP-MODE：3Ω AMP-MODE：4Ω AMP-MODE：8Ω AMP-MODE：120W-70V AMP-MODE：120W-100V AMP-MODE：200W-70V AMP-MODE：200W-100V AMP-MODE：3Ω AMP-MODE：4Ω AMP-MODE：8Ω AMP-MODE：120W-70V AMP-MODE：120W-100V AMP-MODE：200W-70V AMP-MODE：200W-100V 120V/60Hz Idle 1/8 output power 1/3 output power Sleep AMP-MODE：3Ω/4Ω/8Ω AMP-MODE : 120W-70V/100V AMP-MODE：200W-70V/100V AMP-MODE：3Ω AMP-MODE：4Ω AMP-MODE：8Ω AMP-MODE：120W-70V AMP-MODE：120W-100V AMP-MODE：200W-70V AMP-MODE：200W-100V AMP-MODE：3Ω AMP-MODE：4Ω AMP-MODE：8Ω AMP-MODE：120W-70V AMP-MODE：120W-100V AMP-MODE：200W-70V AMP-MODE：200W-100V 100V/50Hz Idle 1/8 output power 1/3 output power Sleep AMP-MODE：3Ω/4Ω/8Ω AMP-MODE : 120W-70V/100V AMP-MODE：200W-70V/100V AMP-MODE：3Ω AMP-MODE：4Ω AMP-MODE：8Ω AMP-MODE：120W-70V AMP-MODE：120W-100V AMP-MODE：200W-70V AMP-MODE：200W-100V AMP-MODE：3Ω AMP-MODE：4Ω AMP-MODE：8Ω AMP-MODE：120W-70V AMP-MODE：120W-100V AMP-MODE：200W-70V AMP-MODE：200W-100V Line Current (A) 230V 0.10 0.21 0.26 0.22 0.54 0.57 0.52 0.55 0.55 0.49 0.48 1.02 1.10 0.98 1.01 1.02 0.91 0.90 Watt (W) In 3.3 18 23 18 52 56 50 53 53 47 46 106 115 101 105 106 94 92 Line Current (A) 120V 0.08 0.28 0.37 0.30 0.87 0.92 0.82 0.88 0.88 0.78 0.77 1.65 1.78 1.59 1.64 1.65 1.49 1.46 In 2.5 16 21 17 52 55 49 52 52 46 45 107 117 102 106 107 94 93 Line Current (A) 100V 0.07 0.31 0.42 0.33 0.99 1.05 0.94 1.00 1.00 0.90 0.87 1.90 2.05 1.83 1.89 1.91 1.71 1.68 In 2.4 16 21 17 52 55 49 53 53 46 45 108 119 103 107 108 95 94 Out 0.0 0.0 0.0 0.0 23 26 24 25 26 23 23 61 68 63 67 69 60 61 Thermal Dissipation Dissipated 3.3 18 23 18 29 30 26 28 27 24 23 45 47 38 38 37 34 31 Watt (W) Out 0.0 0.0 0.0 0.0 23 25 24 25 26 23 23 61 68 63 67 69 60 61 kcal/h 2.9 15 20 16 25 26 22 24 23 21 20 39 41 33 33 32 29 27 Thermal Dissipation Dissipated 2.5 16 21 17 29 30 25 27 26 23 22 46 49 39 39 38 34 32 Watt (W) Out 0.0 0.0 0.0 0.0 23 25 23 25 26 23 23 61 68 63 67 69 60 61 Btu/h 11.3 60 79 63 99 103 89 96 93 82 79 154 161 130 130 127 117 106 Btu/h 8.6 54 72 57 99 103 86 93 89 79 75 158 168 134 134 130 117 110 kcal/h 2.2 14 18 14 25 26 22 23 22 20 19 40 42 34 34 33 29 28 Thermal Dissipation Dissipated 2.4 16 21 17 29 30 26 28 27 23 22 47 51 40 40 39 35 33 Btu/h 8.2 54 73 57 99 103 89 96 93 79 75 161 175 137 137 134 120 113 kcal/h 2.1 14 18 14 25 26 22 24 23 20 19 41 44 35 35 34 30 29 MA2120 Setup Guide 169  Yamaha Pro Audio global website http://www.yamahaproaudio.com/ Yamaha Downloads http://download.yamaha.com/ 䳻傢૾҆ಞ丩ଃδѣളεᣋ䍺ᴿ䲆‫ޢ‬ਮ р⎭ᐸ䶏ᆿ॰᯦䰮䐥ਭӇૂཝড়ᾲ ᇘᡭᵃࣗ✣㓵φ ‫ޢ‬ਮ㖇൶φKWWSZZZ\DPDKDFRPFQ স੃䳻傢૾⭫ᆆδ㤅ᐔεᴿ䲆‫ޢ‬ਮ স൶⊕㤅ⴷ㤅ᐔᐸ㤅ᐔ᯦॰咵ኧ䐥ਭ Manual Development Department © 2016 Yamaha Corporation Published 02/2016 ਇ㺂 KSHD-A0 Printed in China ZT16370