Yamaha CLP-725 de handleiding

Merk: Yamaha

Model: CLP-725

Categorie: Aanvullende muziekapparatuur

Type: de handleiding

Owner’s Manual

Mode d’emploi

CLP

725

EnglishFrançais

Before using the instrument, be sure to read “PRECAUTIONS” on pages 5-6.

For information on assembling the instrument, refer to the instructions on page 31.

Avant d’utiliser l’instrument, lisez attentivement la section « PRÉCAUTIONS D’USAGE »

aux pages 5 et 6.

Pour plus d’informations sur l’assemblage de l’instrument, reportez-vous aux instructions

figurant en page 31.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instruc-

tions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may

void your authority, granted by the FCC, to use the prod-

uct.

2. IMPORTANT: When connecting this product to accesso-

ries and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used.

Follow all installation instructions. Failure to follow instruc-

tions could void your FCC authorization to use this prod-

uct in the USA.

3. NOTE: This product has been tested and found to com-

ply with the requirements listed in FCC Regulations, Part

15 for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance

that your use of this product in a residential environment

will not result in harmful interference with other electronic

devices. This equipment generates/uses radio frequen-

cies and, if not installed and used according to the instruc-

tions found in the users manual, may cause interference

harmful to the operation of other electronic devices. Com-

pliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product

is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try

to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to dis-

tribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Corporation

of America, Electronic Service Division, 6600 Orangetho-

rpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products dis-

tributed by Yamaha Corporation of America or its subsid-

iaries.

* This applies only to products distributed by Yamaha Corporation of America. (class B)

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

Yamaha Corporation of America.

COMPLIANCE INFORMATION STATEMENT

(Supplierʼs declaration of conformity procedure)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Digital Piano

Model Name : CLP-725

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference

that may cause undesired operation.

(FCC SDoC)

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an

equilateral triangle is intended to alert the

user to the presence of important operating

and maintenance (servicing) instructions in

the literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

9 Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories specified by

the manufacturer.

12 Use only with the cart,

stand, tripod, bracket, or

table specified by the

manufacturer, or sold with

the apparatus. When a cart

is used, use caution when

moving the cart/apparatus

combination to avoid injury

from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has

been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE.

For AC adaptor

CLP-725 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

• This AC adaptor is designed for use with only Yamaha electronic

instruments. Do not use for any other purpose.

• Indoor use only. Do not use in any wet environments.

CAUTION

• When setting up, make sure that the AC outlet is easily accessible. If

some trouble or malfunction occurs, immediately turn off the power

switch of the instrument and disconnect the AC adaptor from the

outlet. When the AC adaptor is connected to the AC outlet, keep in

mind that electricity is flowing at the minimum level, even if the power

switch is turned off. When you are not using the instrument for a long

time, make sure to unplug the power cord from the wall AC outlet.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or

radiators. Also, do not excessively bend or otherwise damage the cord,

or place heavy objects on it.

• Only use the voltage specified as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

• Use the specified adaptor (page 34) only. Using the wrong adaptor can

result in damage to the instrument or overheating.

• Use only the supplied power cord/plug.

• Check the electric plug periodically and remove any dirt or dust which

may have accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the

instrument or attempt to disassemble or modify the internal

components in any way. If it should appear to be malfunctioning,

discontinue use immediately and have it inspected by qualified

Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or

wet conditions, or place on it any containers (such as vases, bottles or

glasses) containing liquids which might spill into any openings. If any

liquid such as water seeps into the instrument, turn off the power

immediately and unplug the power cord from the AC outlet. Then have

the instrument inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item

may fall over and cause a fire.

• Do not place the bench in an unstable position where it might

accidentally fall over.

• Do not play carelessly with or stand on the bench. Using it as a tool or

stepladder or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent

the possibility of accident or injury.

• If the bench screws become loose due to extensive long-term use,

tighten them periodically using the specified tool in order to prevent

the possibility of accident or injury.

• Keep special watch over any small children so that they don’t fall off

the rear of the bench. Since the bench does not have a backrest,

unsupervised use may result in accident or injury.

• When one of the following problems occur, immediately turn off the

power switch and disconnect the electric plug from the outlet. Then

have the device inspected by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

- If any cracks or breakages exist on the instrument.

For the AC adaptor

For the instrument

Power supply/AC adaptor

Do not open

Water warning

Fire warning

Using the bench (If included)

If you notice any abnormality

DMI-7 1/2

CLP-725 Owner’s Manual

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-

connector. Doing so can result in lower sound quality, or possibly

cause overheating in the outlet.

• When removing the electric plug from the instrument or an outlet,

always hold the plug itself and not the cord. Pulling by the cord can

damage it.

• Remove the electric plug from the outlet when the instrument is not to

be used for extended periods of time, or during electrical storms.

• Assemble the instrument in the proper sequence by following the

assembly instructions in this manual. Also, make sure to tighten the

screws regularly. Failure to do so might result in damage to the

instrument or even injury.

• Do not place the instrument in an unstable position where it might

accidentally fall over.

• Do not go near the instrument during an earthquake. Strong shaking

during an earthquake could cause the instrument to move or tip over,

resulting in damage to the instrument or its parts, and possibly

causing injury.

• When transporting or moving the instrument, always use two or more

people. Attempting to lift the instrument by yourself may damage your

back, result in other injury, or cause damage to the instrument itself.

• Before moving the instrument, remove all connected cables, to prevent

damage to the cables or injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction occurs,

immediately turn off the power switch and disconnect the plug from the

outlet. Even when the power switch is turned off, electricity is still

flowing to the product at the minimum level. When you are not using

the product for a long time, make sure to unplug the power cord from

the wall AC outlet.

• Before connecting the instrument to other electronic components, turn

off the power for all components. Before turning the power on or off for

all components, set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels

and gradually raise the volume controls while playing the instrument to

set the desired listening level.

• Do not insert a finger or hand in any gaps on the key cover or

instrument. Also take care that the key cover does not pinch your

finger.

• Never insert or drop paper, metallic, or other objects into the gaps on

the key cover, panel or keyboard. This could cause physical injury to

you or others, damage to the instrument or other property, or

operational failure.

• Do not rest your weight on, or place heavy objects on the instrument,

and do not use excessive force on the buttons, switches or connectors.

• Keep small parts out of the reach of infants. Your children may

accidentally swallow them.

• Do not use the instrument/device or headphones for a long period of

time at a high or uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing loss or ringing

in the ears, consult a physician.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (power

indicator is off), electricity is still flowing to the instrument at the

minimum level.

When you are not using the instrument for a long time, make sure you

unplug the power cord from the wall AC outlet.

Power supply/AC adaptor

Assembly

Location

Yamaha cannot be held responsible for damage caused by improper use or

modifications to the instrument, or data that is lost or destroyed.

Connections

Handling caution

DMI-7 2/2

The model number, serial number, power requirements, etc., may be found on or

near the name plate, which is at the bottom of the unit. You should note this

serial number in the space provided below and retain this manual as a perma-

nent record of your purchase to aid identification in the event of theft.

Model No.

Serial No.

(bottom_en_01)

The name plate is located on the bottom of the unit.

CLP-725 Owner’s Manual

NOTICE

To avoid the possibility of malfunction/ damage to the product,

damage to data, or damage to other property, follow the notices

below.

 Handling

• Do not use the instrument in the vicinity of a TV, radio,

stereo equipment, mobile phone, or other electric devices.

Otherwise, the instrument, TV, or radio may generate noise.

• When you use the instrument along with an app on your

smart device such as a smartphone or tablet, we recommend

that you enable “Airplane Mode” on that device in order to

avoid noise caused by communication.

• Do not expose the instrument to excessive dust or

vibrations, or extreme cold or heat (such as in direct

sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disfiguration, damage to the internal

components or unstable operation. (Verified operating

temperature range: 5° – 40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the

instrument, since this might discolor the panel or keyboard.

• In the case of a model with a polished finish, bumping the

surface of the instrument with metal, porcelain, or other

hard objects can cause the finish to crack or peel. Use

caution.

 Maintenance

• When cleaning the instrument, use a soft and dry/slightly

damp cloth. Do not use paint thinners, solvents, alcohol,

cleaning fluids, or chemical-impregnated wiping cloths.

• In the case of a model with a polished finish, gently remove

dust and dirt with a soft cloth. Do not wipe too hard since

small particles of dirt can scratch the instrument's finish.

• During extreme changes in temperature or humidity,

condensation may occur and water may collect on the

surface of the instrument. If water is left, the wooden parts

may absorb the water and be damaged. Make sure to wipe

any water off immediately with a soft cloth.

 Saving data

• Some of the data of this instrument (page 29) are retained

when the power is turned off. However, the saved data may

be lost due to some failure, an operation mistake, etc. Save

your important data onto an external device such as a

computer (page 29).

Information

 About copyrights

• Copying of the commercially available musical data

including but not limited to MIDI data and/or audio data is

strictly prohibited except for your personal use.

• This product incorporates and bundles contents in which

Yamaha owns copyrights or with respect to which Yamaha

has license to use others’ copyrights. Due to copyright laws

and other relevant laws, you are NOT allowed to distribute

media in which these contents are saved or recorded and

remain virtually the same or very similar to those in the

product.

* The contents described above include a computer

program, Accompaniment Style data, MIDI data, WAVE

data, voice recording data, a score, score data, etc.

* You are allowed to distribute medium in which your

performance or music production using these contents is

recorded, and the permission of Yamaha Corporation is

not required in such cases.

 About functions/data bundled with the

instrument

• Some of the preset songs have been edited for length or

arrangement, and may not be exactly the same as the

original.

 About this manual

• The illustrations as shown in this manual are for

instructional purposes only, and may appear somewhat

different from those on your instrument.

• The letters at the end of the model name (such as “B,” “PE”)

indicate the color or finish of the instrument. Since they

simply indicate the appearance, these letters are omitted in

this manual.

• Windows is a registered trademark of Microsoft®

Corporation in the United States and other countries.

• iPad and iPhone are trademarks of Apple Inc., registered in

the U.S. and other countries.

• Android™ is a trademark of Google LLC.

• The company names and product names in this manual are

the trademarks or registered trademarks of their respective

companies.

 Tuning

• Unlike an acoustic piano, this instrument does not need to

be tuned by an expert (although the pitch can be user-

adjusted to match other instruments). This is because the

pitch of digital instruments is always maintained perfectly.

CLP-725 Owner’s Manual

Table of Contents

PRECAUTIONS .................................... 5

About the Manuals ................................ 9

Included Accessories ............................. 9

Panel Controls and Terminals ............10

Basic Operations

Setting Up.............................................11

Key Cover ..................................................................11

Music Rest .................................................................11

Turning the Power On.............................................12

Auto Power Off Function........................................12

Using Headphones ...................................................13

Playing the Piano..................................14

Using the Pedals........................................................14

Turning the VRM Effect On/Off............................14

Intelligent Acoustic Control (IAC)........................15

Grand Expression Modeling...................................15

Turning the Operation Confirmation Sounds

On/Off........................................................................16

Changing the Touch Sensitivity .............................16

Using the Metronome..............................................17

Advanced Operations

Playing Various Musical Instrument

Sounds (Voices)....................................18

Selecting a Voice.......................................................18

Listening to the Demo Songs ..................................19

Adding Variations to the Sound (Reverb) ............20

Transposing the Pitch in Semitones ......................21

Fine-tuning the Pitch ...............................................21

Layering Two Voices (Dual mode) ........................22

Playing Duo...............................................................23

Song Playback and Practice .................24

Listening to 50 Preset Songs....................................24

Listening to Songs Loaded from the Computer ...24

Practicing a One-Hand Part....................................25

Playing Back Immediately from the First Note

(Quick Play) ..............................................................25

Recording Your Performance .............26

Recording Your Performance ................................ 26

Changing the Initial Settings of the Recorded Song

....................................................................................27

Deleting Recorded Data ..........................................27

Using with a Computer or a Smart

Device ................................................... 28

Using an App on Your Smart Device.................... 28

Playback/Recording of Audio Data (USB Audio

Interface) ................................................................... 28

Backing up Data and Initializing the

Settings................................................. 29

Data Maintained When Power is Turned Off...... 29

Saving User Song data to a computer ...................29

Initializing the Settings............................................ 29

Confirming the firmware version of this

instrument................................................................. 29

Appendix

Troubleshooting ..................................30

Glossary of Terms ................................30

Keyboard Stand Assembly...................31

Specifications .......................................34

Index.....................................................35

CLP-725 Owner’s Manual

Thank you for purchasing this Yamaha Digital Piano!

This instrument provides exceptionally high-quality sound

and expressive control for your playing enjoyment.

We recommend that you read this manual carefully so that you can fully take advantage of the

advanced and convenient functions of the instrument. We also recommend that you keep this

manual in a safe and handy place for future reference.

About the Manuals

This instrument has the following manuals.

 Included Manuals

Owner’s Manual (this book)

Explains how to use the instrument.

Quick Operation Guide (separate

sheet)

Shows in chart form the functions assigned to the

buttons and the keyboard for quick

understanding.

 Online Manuals (PDF)

Smart Device Connection Manual

Explains how to connect the instrument to a smart

device such as smartphone or tablet, etc.

Computer-related Operations

Includes instructions on connecting this

instrument to a computer, and operations related

to transferring Song data.

MIDI Reference

Contains the MIDI Data Format and MIDI

Implementation chart, as well as descriptions on

MIDI functions such as MIDI channel and Local

Control settings.

To obtain these materials, access the Yamaha

Downloads website, then enter the model name for

searching the desired files.

NOTE

For a general overview of MIDI and how you can effectively use it,

search for “MIDI Basics” (only in English, German, French and

Spanish) on the website above.

Included Accessories

• Owner’s Manual (this book) x1

• Quick Operation Guide (separate sheet) x1

• “50 Classical Music Masterpieces” (music book) x1

• Online Member Product Registration x1

•Warranty* x1

•AC adaptor* x1

•Power cord* x1

•Bench* x1

* May not be included depending on your particular

area. Please check with your Yamaha dealer.

Yamaha Downloads

https://download.yamaha.com/

Smart device app “Smart Pianist”

With the specially developed “Smart Pianist”

app running on your smart device, you can

remotely control your digital piano for even

more convenience and flexibility. By

presenting various parameters on-screen, this

app allows you to make settings in a visual,

more intuitive manner. For more details on

“Smart Pianist,” refer to the following Yamaha

website.

https://www.yamaha.com/kbdapps/

The connection wizard of the “Smart Pianist”

helps you to connect this instrument to your

smart device properly. To start the Connection

Wizard, tap “ ” (Menu) located at the upper

left of the screen to open the Menu display,

and then tap “Instrument” → “Start

Connection Wizard.”

CLP-725 Owner’s Manual

Panel Controls and Terminals

[ ] (Standby/On) switch......................... page 12

For turning the power on or setting to standby.

[MASTER VOLUME] knob

For adjusting the volume of the entire sound.

[DEMO/SONG] button..................... pages 19, 24

For playing the Demo Songs and the Preset Songs.

[PIANO/VOICE] button............. pages 18, 20, 22

For selecting a single Voice, two Voices for layering or

a Reverb Type.

[METRONOME] button .......................... page 17

For starting or stopping the metronome.

[+R], [–L] buttons ................. pages 17, 18, 24, 25

• In general, these are for selecting the next or

previous Voice.

• During Song playback, these are for selecting the

next or previous Song, and (while holding down

[PLAY]) turning on/off the right-hand and left-

hand Parts individually.

• During Metronome playback, these are for

increasing or decreasing the Tempo.

[REC] button............................................ page 26

For recording your keyboard performance.

[PLAY] button.......................................... page 26

For playing back the recorded performance.

[FUNCTION] ................................... pages 12, 21

Simultaneously holding both [DEMO/SONG] and

[PIANO/VOICE] and pressing a specified key allows

you to change various settings, including Auto Power

off function, Transpose parameters, etc.

[PHONES] jacks....................................... page 13

For connecting a set of standard stereo headphones.

[USB TO HOST] terminal ....................... page 28

For connecting to a computer or a smart device such

as an iPhone or iPad.

[TO PEDAL] jack ..................................... page 32

For connecting the pedal cord.

DC IN jack................................................ page 12

For connecting the AC adaptor.

Pedals ....................................................... page 14

For controlling expression and sustain, just as on an

acoustic piano.

Bottom

(Keyboard side)

Bottom

(Keyboard side)

Bottom

(Keyboard side)

Music braces

Music rest

CLP-725 Owner’s Manual

Basic Operations

Setting Up

To open the key cover:

Lift the cover slightly, then push and slide it to the

end.

To close the key cover:

Slide the cover toward you and gently lower the

cover over the keys.

CAUTION

• Hold the cover with both hands when opening or closing it.

Do not release it until it is fully opened or closed. Be

careful to avoid catching fingers (yours or others,

especially children’s) between the cover and main unit.

• Do not place objects, such as a piece of metal or paper, on

top of the key cover. Small objects placed on the key cover

may fall inside the unit when the cover is opened and may

be nearly impossible to remove. This could cause electric

shock, short circuit, fire or other serious damage to the

instrument.

To raise the music rest:

Music braces allow you to hold the pages of music

books in place.

CAUTION

Do not try to use the music rest in a half-raised position.

When lowering the music rest, do not release your hands

from the music rest until it is all the way down.

To lower the music rest:

Close the Music braces if they are open, and then

lower the music rest by following the instructions

below.

Key Cover

CAUTION

Be careful to avoid catching

your fingers when opening or

closing the cover.

Music Rest

Music braces

Setting Up

CLP-725 Owner’s Manual

1. Connect the plugs of the AC adaptor in

the order shown in the illustration.

WARNING

Use the specified adaptor (page 34) only. The use of

other adaptors may result in irreparable damage to both

the adaptor and the instrument.

CAUTION

When setting up the product, make sure that the AC

outlet you are using is easily accessible. If some trouble

or malfunction occurs, immediately turn off the power

switch and disconnect the plug from the outlet.

NOTE

Follow this procedure in reverse order when disconnecting

the AC adaptor.

2. Turn down the [MASTER VOLUME]

knob to “MIN.”

3. Press the [ ](Standby/On) switch to

turn the power on.

The power indicator on the button lights up to

indicate the power is on.

To adjust the volume of the entire keyboard sound,

use the [MASTER VOLUME] dial while playing the

keyboard.

When you’re ready to turn the power to standby,

press the [ ] (Standby/On) switch again for a

second. The power indicator turns off.

CAUTION

Even when the [ ] (Standby/On) switch is in the standby

status, electricity is still flowing to the instrument at a

minimum level. When not using the instrument for an

extended period of time, be sure to unplug the power

cord from the wall AC outlet.

CAUTION

Do not use this instrument at a high volume level for a

long period of time, to avoid damaging your hearing.

NOTICE

Press only the [ ] (Standby/On) switch when turning the

power on. Any other operations, such as pressing the

keys, buttons or pedals may cause the instrument to

malfunction.

To prevent unnecessary power consumption, this

instrument features an Auto Power Off function

that automatically turns the power off if the

instrument is not operated for approximately

30 minutes.

Default setting: Enabled

While holding down [DEMO/SONG] and

[PIANO/VOICE] simultaneously, press the A#0

key to enable the function or the A0 key to disable

it.

You can also disable the function when turning on

the power to the instrument.

While holding down the A-1 key (the lowest key,

press the [ ] (Standby/On) switch to turn the

instrument on. The [REC] indicator flashes three

times, indicating the Auto Power Off function has

been disabled.

Turning the Power On

AC outlet

AC adaptor

DC IN jack (page 10)

DC plug

Power cord

AC plug

The shape of the plug and outlet differ depending on the

locale.

Power

indicator

Auto Power Off Function

A#0 (Enable)

Lowest key

A0 (Disable)

Lowest key

Setting Up

CLP-725 Owner’s Manual

Since this instrument is equipped with two

[PHONES] jacks, you can connect two sets of

standard stereo headphones. If you are using only

one set of headphones, insert a plug into either

jack, which automatically shuts off the speakers

according to the default setting.

CAUTION

Do not use headphones at a high volume for an extended

period of time; doing so may cause hearing loss.

Using the headphone hanger

You can hang the headphones on this instrument.

For instructions on installing the headphone

hanger, refer to “Keyboard Stand Assembly” on

page 31.

NOTICE

Do not hang anything other than the headphones on the

hanger. Doing so may damage this instrument or the hanger.

Speaker On/Off setting

You can set whether the sound of this instrument is

always output from its built-in speaker or not.

While holding down [DEMO/SONG] and

[PIANO/VOICE] simultaneously, press one of the

D6 – E6 key.

• Off (D6): The speaker will not sound.

• On (D#6): The speaker will always sound regardless of

whether a set of headphones is connected or not.

• Normal (E6): The speaker will sound only if

headphones are not connected. (This is the default

setting.)

NOTE

When this is set to “On,” Binaural Sampling and Stereophonic

Optimizer below are not effective.

Reproducing the Natural Sensation of

Sound Distance—Binaural Sampling

and Stereophonic Optimizer

This instrument features two advanced

technologies that allow you to enjoy exceptionally

realistic, natural sound, even when listening on

headphones.

Binaural Sampling (“CFX Grand” Voice only)

Binaural Sampling is a method that uses two

special microphones set at the ear position of a

performer and records the sound from a piano as it

would actually be heard. Listening to the sound

with this effect through headphones gives the

impression of being immersed in the sound, as if it

was actually emanating from the piano. Moreover,

you can enjoy the sound naturally for a long time

without ear fatigue. When the default Voice “CFX

Grand” (page 18) is selected, connecting the

headphones automatically enables the binaural

sampling sound.

Stereophonic Optimizer (Piano Voices other

than “CFX Grand”)

Stereophonic Optimizer is an effect which

reproduces the natural sound distance, like with

the sound of Binaural Sampling, even though you

are listening to it on headphones. When a piano

Voice other than “CFX Grand” is selected,

connecting the headphones automatically enables

the Stereophonic Optimizer.

Default setting: On

While holding down [PIANO/VOICE], press the

F#3 key to turn the function on or the F3 key to

turn the function off.

Using Headphones

PHONES

Standard stereo phone

plug

Bottom surface

D#6 (On)

Highest key

D6 (Off)

E6 (Normal)

F3 (Off)

F#3 (On)

CLP-725 Owner’s Manual

Playing the Piano

Damper Pedal (Right)

Pressing this pedal will sustain notes longer.

Releasing this pedal immediately stops (damps)

any sustained notes. This pedal also features a

“half-pedal” function that creates partial sustain

effects, depending on how far down you press the

pedal.

Sostenuto Pedal (Center)

Pressing this pedal while holding the notes will

sustain the pressed notes (as if the Damper Pedal

had been pressed), but all subsequently played

notes will not be sustained. This makes it possible

to sustain a chord or single low note, for example,

while the other notes are played “staccato.”

Soft Pedal (Left)

Pressing this pedal will reduce the volume and slightly change the timbre of the

notes. The notes played before this pedal is pressed are not affected.

VRM (Virtual Resonance Modeling) technology accurately recreates the unique

resonance of an acoustic grand piano’s soundboard and strings. When you select

a piano Voice (page 18), pressing the damper pedal activates the VRM effect. For

details on VRM, see page 30.

While holding down [PIANO/VOICE], press the C#3 key to turn the function

on or the C3 key to turn the function off.

Using the Pedals

When you press the damper

pedal here, this note and the

notes you play before you release

the pedal sustain longer.

When you press the sostenuto

pedal here while holding the

note, the note will sustain as

long as you hold the pedal.

NOTE

If the damper pedal doesn’t

work, make sure that the pedal

cord is properly plugged into

the main unit (page 32).

Half-pedal function

This function allows you to vary

the sustain length depending

on how far the pedal is

pressed. The farther down you

press the pedal, the more the

sound sustains. For example, if

you press the damper pedal

and all notes you are playing

sound a bit murky and loud

with too much sustain, you can

release the pedal half way or

higher to decrease the sustain

(murkiness).

NOTE

While the sostenuto pedal is

held, the organ and strings

Voices sound continuously

without decay after the notes

have been released.

NOTE

When Jazz Organ Voice

(page 18) is selected,

pressing the left pedal

switches between fast/slow

rotation of the rotary speaker.

When the Vibraphone Voice

(page 18) is selected, the left

pedal switches Vibrato on and

off.

Turning the VRM Effe ct On/Off

Lowest key C3 (Off)

C#3 (On)

Default setting:

Playing the Piano

CLP-725 Owner’s Manual

With this function, the sound quality of this instrument is automatically adjusted

and controlled according to the overall volume. Even when the volume is low,

this lets you hear both low sounds and high sounds clearly.

To turn on/off IAC:

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,

press the C#2 key to turn the function on or the C2 key to turn the function off.

To adjust IAC Depth:

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,

press the D2 key to decrease the value, or the E2 key to increase.

The higher the value, the more clearly that low and high sounds are heard at

lower volume levels.

When a piano Voice (page 18) is selected, you can add Grand Expression

Modeling effects, which simulate the physical sound transitions of an actual

piano. When this feature is set to “Dynamic,” you can control extremely subtle

nuances in the performance and sound by changing your playing strength or

touch. When set to “Static,” the nuances are generally fixed. For details on Grand

Expression Modeling, see page 30.

While holding down [PIANO/VOICE], press the A#3 key to turn the function

on or the A3 key to turn the function off.

Intelligent Acoustic Control (IAC)

Default setting:

C#2 (On)

Lowest key

C2 (Off)

Setting range:

-3 – +3

Default setting:

0 (D#2)

Lowest key

D2 (Depth -1)

E2 (Depth +1)

D#2 (Default)

Grand Expression Modeling

Default setting:

Dynamic

A3 (Static)

A#3 (Dynamic)

Lowest key

Playing the Piano

CLP-725 Owner’s Manual

When a setup is changed using a button and key combination, an operation

sound (on, off, click, tempo value input) is sounded. This confirmation sound

can be enabled (on) or disabled (off) as desired.

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,

press the A#-1 key to turn the sounds on or the A-1 key to turn the sounds off.

You can specify the Touch Sensitivity (how the sound responds to the way you

play the keys).

While holding down [PIANO/VOICE], press one of the C6 – D#6 keys.

Turning the Operation Confirmation Sounds On/Off

Default setting:

Lowest key A-1 (Off)

A#-1 (On)

Changing the Touch Sensitivity

NOTE

This setting is disabled with

some Voices, such as an

organ sound.

Default setting:

Medium (C#6)

Key

Touch

Sensitivity

Description

C6 Soft Produces relatively high volume even with light playing strength.

C#6 Medium Standard Touch Sensitivity.

D6 Hard Requires strong playing to produce high volume.

D#6Fixed

The volume level does not change at all regardless of whether you

play the keyboard soft or hard.

C6 Highest key (C7)D6

C#6D#6

Playing the Piano

CLP-725 Owner’s Manual

The metronome feature is convenient for practicing with an accurate tempo.

To start or stop the Metronome, press [METRONOME].

Metronome setting

Voice confirmation of current Tempo value (in English)

While holding down [METRONOME], press the A-1 key (lowest key).

Selecting the Beat (time signature)

While holding down [METRONOME], press one of the C3 – F3 keys.

The first beat is accented with a bell sound and the rest with clicks. Default set is

0 (C3). In this setting, clicks sound in all beats.

Adjusting the Tempo

The Metronome tempo can be set from 5 to 280 beats per minute.

•To increase or decrease the value by 1:

While holding down [METRONOME], press [+R] to increase or [–L] to decrease.

While the metronome is playing, press [+R] to increase or [–L] to decrease.

•To increase or decrease the value by 10:

While holding down [METRONOME], press the D2 key to increase or the C2 key

to decrease.

•To specify a numeric value:

While holding down [METRONOME], press the relevant C1 – A1 keys one by one

in order, and then release [METRONOME] to enter the value.

•Resetting the value to the default (120)

While holding down [METRONOME], press [+R] and [–L] simultaneously, or

press the C#2 key. While the metronome is playing, press [+R] and [–L]

simultaneously.

Adjusting the Volume

While holding down [METRONOME], press the G0 key to increase the volume

or the F0 key to decrease. To reset to the default setting, press the F#0 key while

holding down [METRONOME].

Using the Metronome

22447

13 3056 56

C#3D#3

D3 E3 F3F0 A1G0Lowest key A-1 C1 C2 D2 C3

C#2 (Default setting)F#0 (Default setting)

Volume BeatTempoConfirming the

current Tempo

Key Beat

C3 0 (no accent)

C#32

D3 3

D#34

E3 5

F3 6

Setting range:

1 – 10

Default setting:

7 (F#0)

NOTE

A numeric value is read out

when a relevant key is

pressed.

If the entered value is outside

the setting range, it will be

ignored.

CLP-725 Owner’s Manual

Advanced Operations

Playing Various Musical Instrument Sounds (Voices)

To select “CFX Grand”:

Simply press [PIANO/VOICE].

To select another Voice:

After pressing [PIANO/VOICE], press [+R] or [–L] to select the next or previous

Voi ce .

To select a specific Voice:

While holding down [PIANO/VOICE], press one of the C1 – A1 keys. For details

on which Voice is assigned to each key, see the list below.

Voice List

Selecting a Voice

NOTE

To hear the characteristics of

the Voices, play back the

Demo Songs (page 19).

Key Voice Name Voice description

CFX Grand

Yamaha’s CFX flagship concert grand piano sound with a wide dynamic

range for maximum expressive control. Suitable for playing in any music

genre and style.

Binaural

CFX Grand

Yamaha’s CFX flagship concert grand piano sound sampled by Binaural

Sampling, the method optimized for headphone use. Listening this

through headphones gives the impression of being immersed in the

sound, as if it was actually emanating from the piano. This Voice is

selected automatically when headphones are connected.

C#1 Bösendorfer

The famed sound of the Vienna-made Bösendorfer full concert grand

piano. Its spacious sound evokes the size of the instrument, and is ideal

for expressing tenderness in compositions.

D1 Pop Grand

Bright piano sound. Good for clear expression and “cutting through”

other instruments in an ensemble.

D#1 Stage E.Piano

The sound of an electric piano using hammer-struck metallic “tines.”

Soft tone when played lightly, and an aggressive tone when played

hard.

E1 DX E.Piano

An electronic piano sound created by FM synthesis. Good for standard

popular music.

F1 Harpsichord

The definitive instrument for baroque music. Since harpsichord uses

plucked strings, there is no touch response. There is, however, a

characteristic additional sound when the keys are released.

F#1 Vibraphone

Vibraphone played with relatively soft mallets. The tone becomes more

metallic the harder you play.

G1 Pipe Organ

This is a typical pipe organ sound (8 feet + 4 feet + 2 feet). Good for

sacred music from the Baroque period.

G#1 Jazz Organ

The sound of a “tonewheel” type electric organ. Often heard in jazz and

rock music.

A1 Strings

Stereo-sampled, large-scale strings ensemble with realistic reverb. Try

combining this Voice with piano in the Dual mode.

C#1D#1F#1G#1

C1 D1 E1 F1 G1 A1Lowest key

Playing Various Musical Instrument Sounds (Voices)

CLP-725 Owner’s Manual

Special individual Demo Songs are provided for all of the instrument Voices.

1. Press [DEMO/SONG] to start playback.

The Demo Song for the current Voice starts. During playback, the [PLAY] lamp

flashes at the current tempo.

Starting with the selected song, the playback of the Demo Songs will continue.

After the last demo song, the sequence then returns to the first Demo Song and

repeats until you stop it.

To change the Demo Song during playback:

Press [+R] or [–L] to change to the next or previous Demo Song.

To change to a specific Demo Song, simultaneously hold down [DEMO/SONG]

and press one of the C1 – A1 keys.

2. Press [DEMO/SONG] or [PLAY] to stop playback.

The [PLAY] lamp turns off.

Demo Song List

The Demo Songs excluding original Songs are short rearranged excerpts from the original

compositions. The original Demo Songs are Yamaha originals (© Yamaha Corporation).

Listening to the Demo Songs

NOTE

If you want to change the

playback tempo, see page 17.

Key Voic e Name Title Composer

CFX Grand

Allegro de concierto Cis-Dur E. Granados

Binaural

CFX Grand

C#1 Bösendorfer Widmung S.566 R.253

F. Liszt /

R. Schumann

D1 Pop Grand Original —

D#1 Stage E.Piano Original —

E1 DX E.Piano Original —

F1 Harpsichord

Concerto a cembalo obbligato, 2 violini, viola e

continuo No.7, BWV 1058

J. S. Bach

F#1 Vibraphone Original —

G1 Pipe Organ Herr Christ, der ein'ge Gottes-Sohn, BWV 601 J. S. Bach

G#1 Jazz Organ Original —

A1 Strings Original —

Lowest key C1 A1

Playing Various Musical Instrument Sounds (Voices)

CLP-725 Owner’s Manual

This instrument features several Reverb Types that add extra depth and expression to the sound to create a

realistic acoustic ambience. The appropriate Reverb Type and Depth are called up automatically when you

select each of the Voices and Songs. For this reason, the Reverb Type need not be selected; however, you can

change it if desired.

To select a Reverb Type:

While holding down [PIANO/VOICE], press one of the C2 – E2 keys.

Reverb Type List

To adjust Reverb Depth:

While holding down [PIANO/VOICE], press the G2 key to decrease the value by

1 or the A2 key to increase the value by 1.

While holding down [PIANO/VOICE], press the G#2 key to reset the Reverb

Depth to the default setting, which is the most suitable value for the current

Voi ce .

Adding Variations to the Sound (Reverb)

Reverb in Dual Mode

(page 22)

An optimum reverb type for the

combination of Voices is

assigned automatically.

Key Reverb Type Description

C2 Recital Hall

Simulates the clear reverb sound you would hear in a medium-

sized concert hall for piano recitals.

C#2 Concert Hall

Simulates the gorgeous reverb sound you would hear in a large

concert hall for orchestral performances.

D2 Chamber

Suitable for playing chamber music; simulates the intimate

reverb sound you would hear in a spacious room, such as for

classical music recitals.

D#2Club

Simulates the vivid reverb sound you would hear in a live music

venue or a jazz club.

E2 Off No effect is applied.

Lowest key

A2 (Depth +1)

G#2 (Default)

G2 (Depth -1)

C#2D#2

C2 D2 E2

Reverb Type

Reverb Depth

Setting range:

0 (no effect) – 20 (maximum

depth)

Playing Various Musical Instrument Sounds (Voices)

CLP-725 Owner’s Manual

You can shift the pitch of the entire keyboard up or down in semitones in order to facilitate playing in

difficult key signatures, or to easily match the pitch of the keyboard to the range of a singer or other

instruments. For example, if “+5” is selected, playing key C produces pitch F, letting you play a song of F

major as though it were in C major.

To transpose the pitch down:

While holding down [DEMO/SONG] and [PIANO/VOICE], press a key

between F#2 (-6) and B2 (-1).

To transpose the pitch up:

While holding down [DEMO/SONG] and [PIANO/VOICE], press a key

between C#3 (+1) and F#3 (+6).

To restore the normal pitch:

While holding down [DEMO/SONG] and [PIANO/VOICE], press the C3 key.

You can fine-tune the pitch of the entire instrument in about 0.2 Hz steps. This lets you accurately match the

keyboard pitch to that of other instruments or CD music.

To tune up (in about 0.2 Hz steps):

Press and hold down [DEMO/SONG] and

[PIANO/VOICE] simultaneously, and press [+R].

To tune down (in about 0.2 Hz steps):

Press and hold down [DEMO/SONG] and

[PIANO/VOICE] simultaneously, and press [–L].

To set the pitch to 442.0 Hz:

Press and hold down [DEMO/SONG]

and [PIANO/VOICE] simultaneously,

and press the C#1 key.

To restore default pitch (440.0 Hz):

While simultaneously holding down [DEMO/

SONG] and [PIANO/VOICE], press [+R] and

[–L] simultaneously. Alternately, you can press

the C1 key while holding down [DEMO/

SONG] and [PIANO/VOICE] simultaneously.

Transposing the Pitch in Semitones

NOTE

The transposition setting

affects not only the pitch of the

keyboard but also the pitch of

Song playback (page 24).

The transposition setting of the

Transposition for the Keyboard

and the Song cannot be set

independently.

Setting range:

-6 – 0 – +6

Default setting:

-5 -3 -1 0 +2 +4 +5

-6 -4 -2 +1

+3 +6

F#2

Lowest key

F#3

Transpose down Transpose up

C3 (Normal pitch)

Fine-tuning the Pitch

Hz (Hertz)

This unit of measurement

refers to the frequency of a

sound and represents the

number of times a sound wave

vibrates in a second.

Setting range:

414.8 – 466.8 Hz

Default setting:

A3 = 440.0 Hz

C#1

Lowest key

Playing Various Musical Instrument Sounds (Voices)

CLP-725 Owner’s Manual

You can layer two Voices and play them simultaneously to create a more richly textured sound.

1. Engage the Dual mode.

While holding down [PIANO/VOICE], simultaneously hold down two keys

between C1 and A1 to select the two desired Voices. For information on which

Voices are assigned to the keys, refer to “Voice List” (page 18).

The Voice assigned to the lower key will be designated as Voice 1, and the Voice

assigned to the higher key will be designated as Voice 2. You cannot assign the same

Voice to both Voice 1 and Voice 2 simultaneously in Dual mode.

To shift the Octave for each Voice:

While holding down [PIANO/VOICE], press one of the keys F5 – G5 or A5 – B5 as

shown in the illustration below. For example, pressing the B5 key twice while

holding down [PIANO/VOICE] shifts Voice 1 up by two octaves. To restore the

default setting, simultaneously hold down [PIANO/VOICE] and press the A#5 key

for Voice 1 or the F#5 key for Voice 2.

To adjust the Balance between two Voices:

While holding down [PIANO/VOICE], press the C5 key to decrease the value or

the D5 key to increase. Pressing the C5 key increases the volume of Voice 2, while

pressing the D5 key increases the volume of Voice 1. To reset to the default value for

each combination of Voices, press the C#5 key.

2. To exit from Dual mode, press [PIANO/VOICE].

Layering Two Voices (Dual mode)

C1 A1

Lowest key

Engaging Dual mode

NOTE

The Dual and Duo modes

(page 23) cannot be engaged

at the same time.

Setting range:

-2 – 0 – +2

Setting range:

-6 – (default setting) – +6

Default setting:

Differs depending on the Voice

combination.

-1

+1-1 +1 -1

Highest key

C#5

(Default setting)

F5 B5

Shifting the octave

Adjusting the balance

Voice 2

Voice 1

Playing Various Musical Instrument Sounds (Voices)

CLP-725 Owner’s Manual

This function allows two different players to play the instrument, one on the left and the other on the right,

over the same octave range and with the same Voice.

1. While holding down [PIANO/VOICE], press [+R] and [–L]

simultaneously to engage Duo.

The keyboard is divided into two sections, with the E3 key as the Split Point.

2. One person can play the left section of the keyboard while

the other plays the right.

The pedal function changes as follows.

• Right Pedal: Applies Sustain to the right section.

• Center Pedal: Applies Sustain to both sections.

• Left Pedal: Applies Sustain to the left section.

To shift the O ctave for e a ch sec tion:

Same operation as in Dual (page 22).

To adjust the volume balance between two keyboard sections:

Same operation as in Dual (page 22).

3. To exit from Duo, simultaneously hold down [PIANO/

VOICE] and press [+R] and [–L].

Selecting the Duo type

You can set how the sound is emitted from the speakers. When you select

“Separated,” the sound of left part is emitted from the left speaker, and the sound

of right section is emitted from the right speaker. When you select “Balanced,”

the sound of both parts are emitted from both speakers in a natural balance.

While holding down [PIANO/VOICE], press the A4 key or the A#4 key to

change the setting.

Playing Duo

NOTE

• The Split Point cannot be

changed from E3.

• In Duo, VRM is not effective.

• When the Duo type is set to

“Separated,” Reverb and

Binaural Sampling/

Stereophonic Optimizer are

not effective.

• If the keyboard is in Dual

mode, engaging Duo will exit

from Dual, and Voice 1 is

used over the entire range of

the keyboard.

Split Point E3

Equivalent to C3

(middle C)

Left section (Voice 2) Right section (Voice 1)

Equivalent to C3

(middle C)

Setting range:

-2 – 0 – +2

Setting range:

-6 – 0 – +6

Default setting:

Separated

Highest keyA4 (Separated) A#4 (Balanced)

CLP-725 Owner’s Manual

Song Playback and Practice

In addition to the Demo Songs, Preset Songs are provided for your listening pleasure.

1. Find the number of the Song that you want to play back

from the included “50 Classical Music Masterpieces.”

2. While holding down [DEMO/SONG], press one of the C2 –

C#6 keys to start playback.

The number of each piano Preset Song is assigned to the C2 – C#6 keys.

During playback, the [+R] and [–L] lamps light, and the [PLAY] lamp flashes at the

current tempo. Playback of the Preset Songs continues in sequence, starting with

the selected song. After the last Preset Song, the sequence then returns to the first

Preset Song and repeats until you stop it.

To change the Preset Song during playback:

Press [+R] or [–L] to change to the next or previous Preset Song, or directly select the

desired Song by holding down [DEMO/SONG] and pressing the appropriate key.

To change the tempo during playback:

While holding down [METRONOME], press [+R] or [–L] to increase or decrease

the Tempo value by 1. Other instructions are the same as those of the Metronome

Tempo (page 17).

To play back from the beginning of the Song

During playback, press [+R] and [–L] simultaneously to jump to the playback

position at the beginning of the Song then continue playback at the last specified

tempo.

3. Press [DEMO/SONG] or [PLAY] to stop playback.

The [PLAY], [+R] and [–L] lamps turn off.

You can transfer up to 10 songs from your computer to this instrument and play

them back. For details on transferring Songs from a computer and playing them

back on this instrument, refer to the “Computer-related Operations” section on

the website (page 9).

Types of file that can be exchanged with a computer

Files with a .mid extension (SMF format 0 or 1)

Listening to 50 Preset Songs

Highest key (C7)

Song 1 Song 10 Song 20 Song 30 Song 40

C3 C4 C5

Song 50 (C#6)

NOTE

You can play the keyboard

along with the Preset Song.

You can also change the Voice

played from the keyboard.

Song:

In this manual, performance

data is called a “Song.” This

includes 50 Preset Songs and

Demo Songs.

NOTE

The Preset Songs, Demo

Songs and other Songs (a

maximum of ten) transferred

from a computer can be

played back consecutively

within each category.

NOTE

You can import additional

Songs by loading SMF files

from a computer. For details,

refer to the “Computer-related

Operations” on the website

(page 9).

Listening to Songs Loaded from the Computer

NOTE

Certain MIDI files in SMF format

0 or 1 may contain data that is

not supported by your digital

piano, and such files may not

play as originally intended. If

this is the case, setting the song

playback channels to “1&2”

may enable a better rendition of

the song. For details, refer to

the “Computer-related

Operations” section on the

website (page 9).

Song Playback and Practice

CLP-725 Owner’s Manual

All the Songs except for the Demo (page 19) let you turn on or off the left-hand and right-hand Parts

individually. By turning off [+R], for example, you can practice the right-hand Part while the left-hand Part

is playing back, and vice versa.

1. Start playback of a Preset Song (page 24) or the User Song

(page 26).

2. While holding down [PLAY], press [+R] or [–L] to turn the

Part on/off.

Pressing the same button repeatedly while holding down [PLAY] toggles playback on

and off. The lamp of the button lights to indicate that the corresponding Part is on.

3. Practice the Part which is turned off.

To change the Tempo :

While holding down [METRONOME], press [+R] or [-L] to increase or decrease

the Tempo value by 1. Other instructions are the same as those of the Metronome

Tempo (page 17).

4. Press [PLAY] to stop playback.

This Quick Play feature enables you to specify whether a Song should play back

immediately from the very first note, or play back any silence or rests that exist

before the first note.

To turn on/off Quick Play:

While holding down [DEMO/SONG], press the A#-1 to turn the function on or

A-1 key to turn the function off.

Practicing a One-Hand Part

NOTE

Selecting another Song will

reset the on/off status.

NOTE

Songs 16 – 20 of “50 Classical

Music Masterpieces” are duet

songs. The right-hand Part is

for the first player, and the left-

hand Part is for the second

player.

or Lamp lights when Part is on.

Playing Back Immediately from the First Note (Quick Play)

Default setting:

A#-1(On)

A-1(Off)

Lowest key

CLP-725 Owner’s Manual

Recording Your Performance

Not only can you simply record your keyboard performance (Quick Recording), but you can record two

parts (left-hand and right-hand) separately. The recorded data is called a User Song, and can be saved to a

computer as a Standard MIDI file (SMF; page 29).

1. Select the desired Voice and other parameters, such as beat

(time signature), for recording.

For instructions on selecting a Voice, refer to page 18. If necessary, set other

parameters, such as beat (time signature) and effects, in this step.

2. Engage the Record Ready mode.

Quick Recording

Press [REC] to engage the Record Ready mode. Your keyboard performance will be

automatically recorded to the right-hand part. Note that the already-recorded data

of the right- and left-hand parts will be erased by Quick Recording.

Recording to individual parts

While holding down [REC], press [+R] or [–L] to engage the Record Ready mode

for the Part you want to record.

If data has already been recorded to the other Part, the data in this Part will be

played back while recording.

To turn the Part off or on, press the appropriate part button ([+R] or [-L]) while

holding down [PLAY].

To exit from Record Ready mode:

Simply press [REC].

3. Play the keyboard or press [PLAY] to start recording.

The [REC] lamp lights up while the Recording Part lamp flashes at the current

tempo.

4. Press either [REC] or [PLAY] to stop recording.

The [REC], [PLAY], [+R] and [–L] lamps flash, indicating that the recorded data is

being stored. After the Save operation is completed, the lamps will turn off,

indicating that the Record operation has been completed.

5. To hear the recorded Song, press [PLAY] to start playback.

Press [PLAY] again to stop playback.

To record to the other part

Repeat the steps above. In step 2, follow the instructions of “Recording individual

parts.”

Recording Your Performance

NOTE

The Recording function of this

instrument will record your

keyboard performance as

MIDI data. If you want to

record audio data, you can

connect a computer to the

instrument for that purpose.

Refer to page 28 for details.

NOTE

You can use the Metronome

while recording; however, the

Metronome sound will not be

recorded.

NOTE

If the keyboard is in the Duo

mode (page 23), the data will

be recorded to each Part. The

Part for recording cannot be

specified.

NOTICE

Note that recording your

performance to a part

containing data will replace

already-recorded data with

the new data.

NOTE

If the data capacity of the

instrument approaches full

when you engage Record

Ready mode, the [REC] and

[PLAY] lamps flash quickly for

about three seconds.

To record the right-hand Part ([+R]) To record the left-hand Part ([–L])

NOTICE

Never turn off the power

while the recorded data is

being stored (while the

lamps are flashing).

Otherwise, all recorded data

will be lost.

Recording Capacity

This instrument can record up

to 250 KB (approximately

11,000 notes).

Recording Your Performance

CLP-725 Owner’s Manual

The settings of the following parameters can be changed after the Record operation is completed.

• For individual Parts: Voice, Volume balance (Dual/Duo), Reverb Depth

• For the entire Song: Tempo, Reverb Type

1. Make settings for the above parameters as desired.

2. While holding down [REC], press the desired Part button to

engage Record Ready mode.

The [REC], [PLAY] and selected Part ([+R] or [–L]) lamps flash.

In this status, do not press [PLAY] again or any key. Otherwise, the originally

recorded performance data will be deleted.

3. While holding down [REC], press [PLAY] to exit from

Record Ready mode.

The [REC], [PLAY], [+R] and [–L] lamps flash. After the Save operation is

completed, the lamps will turn off, indicating that the operation has been

completed.

Confirm the setting by playing the Song.

To delete the entire Song:

1. While holding down [REC], press [DEMO/SONG].

The [REC] and [PLAY] lamps flash alternately.

To exit from this status, press [REC].

2. Press [PLAY] to delete the data of the entire Song.

The [REC], [PLAY], [+R] and [–L] lamps flash.

After the operation is completed, all lamps turn off.

To delete a specific Part:

1. While holding down [REC], press [+R] or [–L] (depending

on the Part you want to delete) to engage Record Ready

mode.

The [REC], [PLAY] and selected Part ([+R] or [–L]) lamps flash.

2. Press [PLAY] to start recording without playing the

keyboard.

The selected Part ([+R] or [–L]) lamp flashes.

3. Press [REC] or [PLAY] to stop recording.

All data recorded for the selected Part will be deleted, and the lamp turns off.

Changing the Initial Settings of the Recorded Song

Deleting Recorded Data

NOTE

If a User Song has not been

recorded to the instrument, the

[REC] and [PLAY] lamps flash

quickly for about three

seconds.

CLP-725 Owner’s Manual

Using with a Computer or a Smart Device

By connecting a computer or a smart device to the [USB TO HOST] terminal via a USB cable, you can

transmit/receive performance data and Song data to/from the computer or smart device.

For instructions on connection and transmitting/receiving MIDI data with a

computer, refer to the “Computer-related Operations” on the website (page 9).

For instructions on connection with a smart device, refer to the “Smart Device

Connection Manual” on the website. If you use the smart device app “Smart

Pianist” with the instrument, the connection wizard on the app helps you to

connect the instrument to your smart device properly. For details, see page 9.

By using an app on a smart device, you can take advantage of convenient functions and get more enjoyment

out of this instrument. In particular, with the “Smart Pianist” app running on your smart device, you can

remotely control your digital piano for even more convenience and flexibility.

For information about the compatible smart devices and apps, access the following page:

https://www.yamaha.com/kbdapps/

You can play back audio data on a smart device or a computer with this

instrument. You can also record your keyboard performance as audio data to a

music production app on a smart device or a computer.

Audio Loopback On/Off

You can set whether audio sound input from the [USB TO HOST] terminal is

output to a computer or smart device or not, along with the performance played

on the instrument (Audio Loopback function). To output the audio input sound,

set Audio Loopback to “On.”

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously,

press the G5 key to turn this parameter “Off” or the G#5 key to turn it “On.”

NOTICE

• Use an AB type USB cable

of less than 3 meters. USB

3.0 cables cannot be used.

• Do not place your smart

device in an unstable

position. Doing so may

cause the device to fall and

result in damage.

NOTE

For instructions on using MIDI,

refer to the online manual

“MIDI Reference” (page 9).

Instrument

USB cable

USB conversion

adaptor

Smart device

Computer

USB terminal

Instrument

USB cable

Using an App on Your Smart Device

Playback/Recording of Audio Data (USB Audio Interface)

NOTE

• The volume of the audio sound

input can be adjusted from a

computer or a smart device.

• When using this function on a

computer running Windows,

you will need to install the

Yamaha Steinberg USB Driver

to the computer. For details,

refer to the “Computer-related

Operations” on the website

(page 9).

Default setting: On

NOTICE

If you are using a DAW (digital

audio workstation) with this

instrument, set the Audio

Loopback to OFF. Otherwise,

loud noises may occur,

depending on the settings of

the computer/smart device or

the application software.

G#5 (On)

G5 (Off)

Highest key

CLP-725 Owner’s Manual

Backing up Data and Initializing the Settings

The following settings and data are maintained even if you turn the power off.

Among the data listed above, only User Song data (USERSONG00.MID) can be

transferred to a computer and saved as an SMF file. For details, refer to the

“Computer-related Operations” on the website (page 9).

With this operation, all data (with the exception of the Songs) will be reset to the

factory default settings.

To do this, simultaneously hold down the C7 (the highest) key and turn on the

power.

You can confirm the firmware version of your instrument by audible voice in English.

While holding down [DEMO/SONG] and [PIANO/VOICE] simultaneously, press the B0 key.

About the latest Firmware Version

Yamaha may from time to time update firmware of the product without notice for improvement. Make sure

to check our website for information of the latest release and upgrade the firmware for your instrument.

Data Maintained When Power is Turned Off

•Metronome Volume

• Metronome Beat (time signature)

• Touch Sensitivity

•Tuning

• Intelligent Acoustic Control Depth

• Intelligent Acoustic Control On/Off

• Binaural Sampling/Stereophonic Optimizer On/Off

• Operation Confirmation Sounds On/Off

• Auto Power Off Enable/Disable

•Speaker On/Off

• Duo type Separated/Balanced

•User Song data

• Song data (SMF files) transferred from a computer

Saving User Song data to a computer

NOTICE

Saved data may be lost due

to malfunction or incorrect

operation. Save important

data to an external device

such as a computer.

Initializing the Settings

NOTICE

Never turn off the power

while the Initialize operation

is being executed (that is,

while the [REC], [PLAY], [+R]

and [–L] lamps are flashing).

NOTE

If this instrument somehow

becomes disabled or

malfunctions, turn off the

power then execute

Initialization.

Highest key

Confirming the firmware version of this instrument

Lowest key

CLP-725 Owner’s Manual

Appendix

Troubleshooting

Glossary of Terms

VRM (Virtual Resonance Modeling)

On an actual acoustic piano, if you press the damper pedal and play a key, not only does the string of the pressed key vibrate, it

also causes other strings and the soundboard to vibrate, with each influencing the rest, creating a rich and brilliant resonance that

sustains and expands. The VRM technology featured in this instrument reproduces the complicated interaction between both

string and soundboard resonance, and make the sound more like that of a real acoustic piano. Since resonance instantaneously

occurs depending on the action of the keys and pedal, you can expressively vary the sound by changing the timing of your

pressing the keys, and the timing and depth of your pressing the pedal.

Grand Expression Modeling

On an actual acoustic piano, subtle changes in the sound can be produced by changing your playing touch from when you press

a key to when you release it. For example, when you press a key all the way to its bottom, the key hits the keybed underneath and

the noise reaches the strings, changing the sound slightly. Furthermore, the tone when the damper is lowered onto strings to mute

the sound is changed by how quickly you release the key. The Grand Expression Modeling technology recreates these subtle

changes in the sound that respond to your touch. This allows you to add accents by playing strongly or add resonance by playing

softly to produce superbly expressive sound. A crisp tone can be heard when playing staccato as well as a lingering sound

produced when releasing the keys slowly.

Problem Possible Cause and Solution

Power suddenly and unexpectedly

turns off.

This is normal and the Auto Power Off function may have been activated (page 12).

If desired, disable the Auto Power Off function.

The instrument does not turn on.

The plugs are not properly connected. Make sure that the DC plug is securely inserted

into the DC IN jack on the instrument, and that the AC plug is securely inserted to the AC

outlet (page 12).

A click or pop is heard when the

power is turned on or off.

This is normal when electrical current is being applied to the instrument.

Noise is heard from the speakers

or headphones.

The noise may be due to interference caused by the use of a mobile phone in close

proximity to this instrument. Turn off the mobile phone, or move it further away from this

instrument.

Metronome or Song goes out of

tempo slightly when you play the

keyboard.

This occurs infrequently when Grand Expression Modeling is set to “Dynamic.” If this

happens, set Grand Expression Modeling to “Static” (page 15).

The overall volume is low, or no

sound is heard.

The Master Volume is set too low. Set it to an appropriate level using the [MASTER

VOLUME] knob (page 10).

Make sure a pair of headphones or conversion adaptor is not connected to the

[PHONES] jack (page 13).

The Speaker setting is “Off.” Set the Speaker to “Normal” or “On” (page 13).

Make sure that Local Control is On. For details, refer to the “MIDI Reference” (page 9).

Pedals do not function.

The pedal cord may not be securely connected to the [TO PEDAL] jack. Be sure to

insert the pedal cord all the way until the metal part of the cord plug disappears from

view (page 32).

The damper pedal does not

function as expected.

The damper pedal was pressed when the power was turned on. This is not a

malfunction; release the pedal and press it again to reset the function.

CLP-725 Owner’s Manual

Keyboard Stand Assembly

CAUTION

• Assemble the unit on a hard and flat floor with ample space.

• Be careful not to confuse parts, and be sure to install all

parts in the correct orientation. Please assemble the unit in

accordance with the sequence given below.

• Assembly should be carried out by at least two persons.

• Be sure to use only the included screws of the specified

sizes. Do not use any other screws. Use of incorrect screws

can cause damage or malfunction of the product.

• Be sure to tighten all screws upon completing assembly of

the unit.

• To disassemble the unit, reverse the assembly sequence

given below.

Remove all parts from the package and make sure you

have all of the items.

1. Attach (finger-tighten) C to D and

1-1 Untie and straighten out the bundled pedal

cord.

1-2 Align D and E with each end of C.

1-3 Attach D and E to C by finger-tightening

the long screws (6 x 20 mm).

2. Attach B.

2-1 Align the screw holes on the upper side of B

with the bracket holes on D and E, then

attach the upper corners of B to D and E by

finger-tightening two thin screws (4 x 12

mm).

2-2 While pushing the lower part of D and E

from outside, secure the bottom ends of B

using two tapping screws (4 x 20 mm).

Have a Phillips-head (+) screwdriver of the appropriate size

ready.

Foamed styrol pads

Remove foamed styrol pads from the package, position them on

the floor, then place A on top of them. Position the pads so that

they will not hide the connectors on the bottom of A.

Bundled pedal

cord inside

6 x 20 mm long screws x 4

4 x 12 mm thin screws x 2

4 x 20 mm tapping screws x 4

6 x 16 mm short screws x 6

Power cord x 1

AC adaptor x 1

The power cord and adaptor

may not be included, or may

look different from the illustration

above, depending on your

particular area. Please check

with your Yamaha dealer.

4 x 10 mm thin screws x 2

Cord holder

Headphone hanger x 1

Caps x 4

1-1

1-3

2-1

2-2

2-3

2-2

Keyboard Stand Assembly

CLP-725 Owner’s Manual

2-3 Insert the other two tapping screws (4 x 20

mm) into the other two screw holes to

secure B.

2-4 Securely tighten the screws on the top of B

that were attached in Step 2-1.

3. Secure C.

3-1 Securely tighten the screws on C that were

attached in Step 1-3.

3-2 Attach the caps to the head of the screws.

4. Mount A.

Be sure to place your hands at least 15 cm away

from either end of the main unit when positioning

it.

CAUTION

• Be extra careful not to drop the main unit or let your fingers

be pinched by it.

• Do not hold the main unit in any position other than the

position specified above.

5. Secure A.

5-1 Adjust the position of A so that the left and

right ends of A will project beyond D and E

equally when seen from the front.

5-2 Secure A by tightening the short screws (6 x

16 mm) from the front.

6. Connect the pedal cord and the AC

adaptor.

3-1

3-2

Align the screw holes.

At least 15 cm

5-1

5-2

Keyboard Stand Assembly

CLP-725 Owner’s Manual

6-1 Insert the pedal cord plug to the pedal

connector from the rear.

6-2 Securely wind the cord holder around the

pedal cord.

The cord holder is attached to D.

6-3 Connect one end of the power cord to the

AC adaptor.

6-4 Insert the DC plug of the AC adaptor into

the DC IN jack.

7. Set the adjuster.

Rotate the adjuster until it comes in firm contact

with the floor surface.

8. Attach the headphone hanger.

Use two thin screws (4 x 10 mm) to attach the

hanger as shown in the illustration.

When connecting the pedal

cord, insert the plug securely

until the metal part

disappears from view.

After completing the assembly, please check the

following.

• Are there any parts left over?

 Review the assembly procedure and correct any

errors.

• Is this instrument clear of doors and other

movable fixtures?

 Move the instrument to an appropriate location.

• Does this instrument make a rattling noise when

you shake it?

 Tighten all screws.

• Does the pedal box rattle or give way when you

step on the pedals?

 Turn the adjuster so that it is set firmly against the

floor.

• Are the pedal cord plug and the adaptor plug

inserted securely into the sockets?

 Check the connection.

CAUTION

When moving the instrument, always hold the bottom of

the main unit. Do not hold the key cover or top portion.

Improper handling can result in damage to the

instrument or personal injury.

Transporting

If you move to another location, you can transport the

instrument along with other belongings. You can move the

unit as it is (assembled), or you can disassemble the unit

down to the condition it was in when you first took it out of

the box. Transport the keyboard horizontally. Do not lean

it up against a wall or stand it up on its side. Do not subject

the instrument to excessive vibration or shock. When

transporting the assembled instrument, make sure all

screws are properly tightened and have not been loosened

by moving the instrument.

CAUTION

If the main unit creaks or is otherwise unsteady when

you play on the keyboard, refer to the assembly

diagrams and re-tighten all screws.

Do not hold here.

Hold here.

Separate the adjuster

from the floor surface.

CLP-725 Owner’s Manual

Specifications

* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download

the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.

CLP-725

Product Name Digital Piano

Size/Weight

Width

[For models with polished finish]

1,350 mm (53-1/8")

[1,353 mm (53-1/4")]

Height

[For models with

polished finish]

With music rest closed

849 mm (33-7/16")

[851 mm (33-1/2")]

With music rest raised

1,003 mm (39-1/2")

[1,004 mm (39-1/2")]

Depth

[For models with polished finish]

414 mm (16-5/16")

[415 mm (16-5/16")]

Weight

[For models with polished finish]

43 kg (94 lb, 13 oz)

[45 kg (99 lb, 3 oz)]

Control

Interface

Keyboard

Number of Keys 88

Type GrandTouch-S Keyboard: synthetic ebony and ivory key tops, escapement

Touch Response Hard/Medium/Soft/Fixed

Pedal Number of Pedals 3: Damper (with Half-pedal function), Sostenuto, Soft

Panel Language English

Cabinet

Key Cover Style Sliding

Music Rest Yes (with music braces)

Voices

Tone Generation

Piano Sound Yamaha CFX, Bösendorfer Imperial

Binaural Sampling Yes (CFX Grand Voice only)

Piano Effect

VRM Yes

Grand Expression Modeling Yes

Key-off Samples Yes

Smooth Release Yes

Polyphony (max.) 256

Preset Number of Voices 10

Effects

Types

Reverb 4 types

Intelligent Acoustic Control (IAC) Yes

Stereophonic Optimizer

Yes

Functions

Dual Yes

Duo Yes

Recording/

Playback

(MIDI data

only; audio not

supported.)

Preset Number of Preset Songs 10 Voice Demo Songs, 50 Classics

Recording

Number of Songs 1

Number of Tracks 2

Data Capacity Approx. 250 KB/Song (approx. 11,000 notes)

Format

Playback SMF (Format 0, Format 1)

Recording SMF (Format 0)

Functions Overall Controls

Metronome Yes

Tempo Range 5 – 280

Transpose -6 – 0 – +6

Tuning 414.8 – 440.0 – 466.8 Hz (approx. 0.2 Hz increments)

USB audio interface Yes

Storage and

Connectivity

Storage Internal Memory

Total maximum size approx. 960 KB (User Song: One Song approx. 250 KB,

Loading Song data from a computer: Up to 10 Songs)

Connectivity

DC IN 16V

Headphones Standard stereo phone jack (x 2)

USB TO HOST Yes

Sound System

Amplifiers 20 W x 2

Speakers 12 cm x 2

Power Supply

AC Adaptor PA-300C (or an equivalent recommended by Yamaha)

Power Consumption 12 W (When using PA-300C AC adaptor)

Auto Power Off Yes

Included Accessories

Owner’s Manual, Quick Operation Guide, 50 Classical Music Masterpieces (Music

Book), Online Member Product Registration, Warranty*,

AC adaptor* (PA-300C or an equivalent), Power cord*, Bench*

* May not be included depending on your area. Check with your Yamaha dealer.

Separately Sold Accessories

(May not be available depending on your area.)

Headphones (HPH-150/HPH-100/HPH-50), Wireless MIDI adaptor (UD-BT01),

AC adaptor (PA-300C or an equivalent recommended by Yamaha)

CLP-725 Owner’s Manual

Index

Numerics

50 Preset Songs ...........................................................24

AC adaptor .................................................................12

Accessories ....................................................................9

Audio Loopback .........................................................28

Auto Power Off ...........................................................12

Backing up Data ..........................................................29

Beat .............................................................................17

Binaural Sampling ......................................................13

Computer ...................................................................28

Computer-related Operations .......................................9

Damper Pedal .............................................................14

Delete ..........................................................................27

Demo Song List ...........................................................19

Demo Songs ................................................................19

Dual mode ..................................................................22

Duo .............................................................................23

Firmware version ........................................................29

Grand Expression Modeling ................................ 15, 30

Half-pedal ...................................................................14

Headphones ................................................................13

Hz (Hertz) ...................................................................21

Initializing ...................................................................29

Intelligent Acoustic Control (IAC) .............................15

Key Cover ...................................................................11

Left-hand Part .............................................................25

Manuals ........................................................................9

Metronome .................................................................17

MIDI Reference ............................................................9

Music Rest ..................................................................11

Octave ........................................................................22

Operation Confirmation Sounds ................................16

Panel Controls and Terminals ....................................10

Pedals .........................................................................14

Pitch ........................................................................... 21

Playback .....................................................................24

Power ......................................................................... 12

Practice ....................................................................... 25

Preset Songs ...............................................................24

Quick Operation Guide ................................................ 9

Quick Play ..................................................................25

Recording ...................................................................26

Reverb ........................................................................20

Reverb Depth .............................................................20

Reverb Type ...............................................................20

Reverb Type List .........................................................20

Right-hand Part ..........................................................25

Smart Device ..............................................................28

Smart Device Connection Manual ............................... 9

Smart Pianist ................................................................ 9

Soft Pedal ...................................................................14

Song ...........................................................................24

Sostenuto Pedal ..........................................................14

Speaker .......................................................................13

Stereophonic Optimizer .............................................13

Tempo ........................................................................17

Time signature ...........................................................17

Touch Sensitivity ........................................................16

Transpose ...................................................................21

Tuning ........................................................................21

USB Audio Interface ..................................................28

USB TO HOST ........................................................... 10

Voice .......................................................................... 18

Voice List ...................................................................18

Volume .................................................................10, 17

VRM (Virtual Resonance Modeling) ....................14, 30

(weee_eu_en_02)

(weee_eu_fr_02)

Apache License 2.0

SPDX-License-Identifier: Apache-2.0

Licensed under the Apache License, Version 2.0 (the License); you may not use this file except in compliance with the License.

You may obtain a copy of the License at

www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an AS IS BASIS, WITHOUT

WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

See the License for the specific language governing permissions and limitations under the License.

Modified BSD license

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this

software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR

ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED

TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic

products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in

accordance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative

effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste

disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further

information.

Information on Disposal in other Countries outside the European Union:

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local

authorities or dealer and ask for the correct method of disposal.

Informations concernant la collecte et le traitement des déchets d’équipements électriques et électroniques

Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou

électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.

Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et

électroniques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation

nationale.

En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la

sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui

pourraient advenir lors d'un traitement inapproprié des déchets.

Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et

électroniques, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où

vous avez acheté les produits.

Pour les professionnels dans l'Union européenne :

Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques, veuillez contacter votre

vendeur ou fournisseur pour plus d'informations.

Informations sur la mise au rebut dans d'autres pays en dehors de l'Union européenne :

Ce symbole est seulement valable dans l'Union européenne. Si vous souhaitez vous débarrasser de déchets

d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander

la méthode de traitement appropriée.

Important Notice:

U.S. LIMITED WARRANTY for Customers in the United States

For detailed information about this Yamaha product and warranty service, please either

visit the following website address (printable file is available at our website) or contact

Customer Service at the address or telephone number identified below.

Website Address:

Yamaha.io/ClavinovaWarranty

Customer Service:

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620-1273

Telephone: 800-854-1569

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha

ou au distributeur le plus proche de vous figurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más

cercana o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Toronto, Ontario M1S 3R1,

Canada

Tel: +1-416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620,

U.S.A.

Tel: +1-714-522-9011

MEXICO

Yamaha de México, S.A. de C.V.

Av. Insurgentes Sur 1647 Piso 9, Col. San José

Insurgentes, Delegación Benito Juárez, México,

D.F., C.P. 03900, México

Tel: +52-55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B –

Vila Olímpia – CEP 04551-010 – São Paulo/SP,

Brazil

Tel: +55-11-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.,

Sucursal Argentina

Olga Cossettini 1553, Piso 4 Norte,

Madero Este-C1107CEK,

Buenos Aires, Argentina

Tel: +54-11-4119-7000

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Edificio Torre Davivienda, Piso: 20

Avenida Balboa, Marbella, Corregimiento de Bella

Vista, Ciudad de Panamá, Rep. de Panamá

Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND

Yamaha Music Europe GmbH (UK)

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, U.K.

Tel: +44-1908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH, Branch

Switzerland in Thalwil

Seestrasse 18a, 8800 Thalwil, Switzerland

Tel: +41-44-3878080

AUSTRIA/CROATIA/

CZECH REPUBLIC

HUNGARY/ROMANIA/SLOVAKIA/

SLOVENIA

Yamaha Music Europe GmbH, Branch Austria

Schleiergasse 20, 1100 Wien, Austria

Tel: +43-1-60203900

POLAND

Yamaha Music Europe GmbH

Sp.z o.o. Oddział w Polsce

ul. Wielicka 52, 02-657 Warszawa, Poland

Tel: +48-22-880-08-88

BULGARIA

Dinacord Bulgaria LTD.

Bul.Iskarsko Schose 7 Targowski Zentar Ewropa

1528 Sofia, Bulgaria

Tel: +359-2-978-20-25

MALTA

Olimpus Music Ltd.

Valletta Road, Mosta MST9010, Malta

Tel: +356-2133-2093

NETHERLANDS/BELGIUM/

LUXEMBOURG

Yamaha Music Europe, Branch Benelux

Clarissenhof 5b, 4133 AB Vianen, The Netherlands

Tel: +31-347-358040

FRANCE

Yamaha Music Europe

7 rue Ambroise Croizat, Zone d'activités de Pariest,

77183 Croissy-Beaubourg, France

Tel: +33-1-6461-4000

ITALY

Yamaha Music Europe GmbH, Branch Italy

Via Tinelli N.67/69 20855 Gerno di Lesmo (MB),

Italy

Tel: +39-039-9065-1

SPAIN/PORTUGAL

Yamaha Music Europe GmbH Ibérica, Sucursal

en España

Ctra. de la Coruña km. 17,200, 28231

Las Rozas de Madrid, Spain

Tel: +34-91-639-88-88

GREECE

Philippos Nakas S.A. The Music House

19th klm. Leof. Lavriou 190 02 Peania – Attiki,

Greece

Tel: +30-210-6686260

SWEDEN

Yamaha Music Europe GmbH Germany filial

Scandinavia

JA Wettergrensgata 1, 400 43 Göteborg, Sweden

Tel: +46-31-89-34-00

DENMARK

Yamaha Music Denmark,

Fillial of Yamaha Music Europe GmbH, Tyskland

Generatorvej 8C, ST. TH., 2860 Søborg, Denmark

Tel: +45-44-92-49-00

FINLAND

F-Musiikki Oy

Antaksentie 4

FI-01510 Vantaa, Finland

Tel: +358 (0)96185111

NORWAY

Yamaha Music Europe GmbH Germany -

Norwegian Branch

Grini Næringspark 1, 1332 Østerås, Norway

Tel: +47-6716-7800

ICELAND

Hljodfaerahusid Ehf.

Sidumula 20

IS-108 Reykjavik, Iceland

Tel: +354-525-5050

CYPRUS

Nakas Music Cyprus Ltd.

Nikis Ave 2k

1086 Nicosia

Tel: + 357-22-511080

Major Music Center

21 Ali Riza Ave. Ortakoy

P.O.Box 475 Lefkoşa, Cyprus

Tel: (392) 227 9213

RUSSIA

Yamaha Music (Russia) LLC.

Room 37, entrance 7, bld. 7, Kievskaya street,

Moscow, 121059, Russia

Tel: +7-495-626-5005

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

Yamaha Music Gulf FZE

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

TURKEY

Yamaha Music Europe GmbH

Merkezi Almanya Türkiye İstanbul Şubesi

Mor Sumbul Sokak Varyap Meridian Business

1.Blok No:1 113-114-115

Bati Atasehir Istanbul, Turkey

Tel: +90-216-275-7960

ISRAEL

RBX International Co., Ltd.

P.O Box 10245, Petach-Tikva, 49002

Tel: (972) 3-925-6900

OTHER COUNTRIES

Yamaha Music Gulf FZE

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co., Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: +86-400-051-7700

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: +852-2737-7688

INDIA

Yamaha Music India Private Limited

P-401, JMD Megapolis, Sector-48, Sohna Road,

Gurugram-122018, Haryana, India

Tel: +91-124-485-3300

INDONESIA

PT. Yamaha Musik Indonesia (Distributor)

Yamaha Music Center Bldg. Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: +62-21-520-2577

KOREA

Yamaha Music Korea Ltd.

11F, Prudential Tower, 298, Gangnam-daero,

Gangnam-gu, Seoul, 06253, Korea

Tel: +82-2-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn. Bhd.

No.8, Jalan Perbandaran, Kelana Jaya, 47301

Petaling Jaya, Selangor, Malaysia

Tel: +60-3-78030900

SINGAPORE

Yamaha Music (Asia) Private Limited

Block 202 Hougang Street 21, #02-00,

Singapore 530202, Singapore

Tel: +65-6740-9200

TAIWAN

Yamaha Music & Electronics Taiwan Co., Ltd.

2F., No.1, Yuandong Rd., Banqiao Dist.,

New Taipei City 22063, Taiwan (R.O.C.)

Tel: +886-2-7741-8888

THAILAND

Siam Music Yamaha Co., Ltd.

3, 4, 15, 16th Fl., Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: +66-2215-2622

VIETNAM

Yamaha Music Vietnam Company Limited

15th Floor, Nam A Bank Tower, 201-203 Cach

Mang Thang Tam St., Ward 4, Dist.3,

Ho Chi Minh City, Vietnam

Tel: +84-28-3818-1122

OTHER ASIAN COUNTRIES

https://asia-latinamerica-mea.yamaha.com/

index.html

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 80 Market Street, South Melbourne,

VIC 3205 Australia

Tel: +61-3-9693-5111

NEW ZEALAND

Music Works LTD

P.O.BOX 6246 Wellesley, Auckland 4680,

New Zealand

Tel: +64-9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

https://asia-latinamerica-mea.yamaha.com/

index.html

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

DMI27

Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan

(For European Countries) Importer: Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany

Manual Development Group

Published 02/2020 MWMA*.*-**A0

VCR9660

https://www.yamaha.com/

Yamaha Global Site

https://download.yamaha.com/

Yamaha Downloads

Yamaha CLP-725 de handleiding

Merk: Yamaha

Model: CLP-725

Categorie: Aanvullende muziekapparatuur

Type: de handleiding

Download PDF

rapport

in andere talen

English: Yamaha CLP-725 Owner's manual
italiano: Yamaha CLP-725 Manuale del proprietario
русский: Yamaha CLP-725 Инструкция по применению
français: Yamaha CLP-725 Le manuel du propriétaire
español: Yamaha CLP-725 El manual del propietario
Deutsch: Yamaha CLP-725 Bedienungsanleitung
português: Yamaha CLP-725 Manual do proprietário
dansk: Yamaha CLP-725 Brugervejledning
čeština: Yamaha CLP-725 Návod k obsluze
polski: Yamaha CLP-725 Instrukcja obsługi
română: Yamaha CLP-725 Manualul proprietarului

Yamaha CLP-725 de handleiding

Yamaha CLP-725 de handleiding

in andere talen

Gerelateerde artikelen