LI4278 LINEAR IMAGER
LI4278 LINEAR IMAGER
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
72-154896-08 Revision A - February 2023
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp.,
registered in many jurisdictions worldwide. All other trademarks are the property
of their respective owners.
© 2023 Zebra Technologies Corp. and/or its aliates. All rights reserved.
SCAN SUFFIX
AVOID EXTREME
WRIST ANGLES
AVOID REACHING
AVOID BENDING
012345 012345
TROUBLESHOOTING
Low/medium/high beep
Power up
Short medium beep
Bar code decoded
4 long low beeps
Transmission error detected;
data is ignored
4 short beeps
Low battery
Standard Use Hand-Held Scanning
High/low beep
Correct programming
sequence performed
Low/high beep
Incorrect programming sequence
or “Cancel” bar code scanned
High/low/high/low beep
Successful
parameter setting
Parameter Menu Scanning
BEEPER INDICATIONS LED INDICATIONS
O
Scanner is on and ready to scan,
or no power to scanner
Green
Bar code is successfully decoded
Red
Transmission error
Hands-Free (Presentation) Scanning
O
No power to
scanner
O Momentarily
Bar code is
successfully decoded
Green
Scanner is ready
to scan
Red
Transmission error
Local Contact:
SCANNING
High/low beep
Bluetooth
disconnection
Low/high beep
Bluetooth connection
established
High/low/high/low beep
Pairing bar code
scanned
Wireless Operation Charging
O
No power to
scanner
Green - Fast Continuous
Scanner is charging
Green - Slow Continuous
Non-critical battery
temperature fault
Green - Solid
Scanner is fully charged
Aiming
No power to scanner
Check system power; battery may be discharged;
charge scanner in cradle; check battery door is closed;
ensure battery end cap is secured
Scanner is disabled
Ensure that correct host
interface cable is used
Scan appropriate host
parameter bar codes
Ensure all cable connections
are secure
Scanner not working
Bar code unreadable
Ensure bar code is not defaced;
try scanning test bar code of same
bar code type
Distance between scanner
and bar code incorrect
Move scanner closer to
or further from bar code
Scanner not programmed
for bar code type
Ensure scanner is programmed to read
type of bar code being scanned
Scanner not decoding bar code
Scanner not programmed for
correct host interface
Interface cable is loose
Scanner decoding bar code, but data not transmitting to host
Scanner not programmed for correct host interface
Scan appropriate host parameter bar codes
Scanned data incorrectly displayed on host
Pair the scanner to
the cradle
Scanner not paired to
host-connected interface
In this order: disconnect power supply; disconnect
host cable; wait three seconds; reconnect host cable;
reconnect power supply; reestablish pairing
Cradle lost connection to host
Battery is above or below normal operating temperature
Do not use scanner; move scanner to location with normal operating temperature;
refer to the Product Reference Guide for more information
LED indicates battery temperature
Low battery start-up
Wait for red LED to turn green
indicating scanner is charging
Cradle communication error
Inspect contacts; remove and reinsert
scanner in cradle
LED indicates low battery start-up
RECOMMENDED USAGE GUIDE - OPTIMUM BODY POSTURE
REGULATORY INFORMATION
Health and Safety Recommendations
Avoid Extreme Wrist Angles Avoid ReachingAvoid Bending
POST IN
WORK AREA
B
Zebra reserves the right to make changes to any product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of
any product, circuit, or application described herein. No license is granted, either expressly or by implication,
estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Zebra products might be used. An implied
license exists only for equipment, circuits, and subsystems contained in Zebra products.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem
with the equipment, they will contact the Zebra Global Customer Support Center at:
http://www.zebra.com/support.
For the latest version of this guide go to: http://www.zebra.com/support.
Power Supply
Use only approved power supply. The power supply shall be Listed to UL/CSA 60950-1 and certied to
IEC60950-1 and EN60950-1 with SELV outputs. Use of alternative power supply will invalidate any
approval given to this device and may be dangerous.
TURKISH WEEE Statement of Compliance
EEE Yönetmeliğine Uygundur
Korea Warning Statement for Class B ITE
Aim/Illumination
Optical Output: 0.87mW
Pulse Duration: Continuous
Emitted Wavelength: 590-650nm
Viewing the LED output with certain optical instruments (for example, eye loupes, magniers
and microscopes) may pose an eye hazard.
Caution: Use of controls or adjustments or performance of procedures other than those
specied herein may result in hazardous LED light exposure.
Japan (VCCI) - Voluntary Control Council for Interference
Class B ITE
Marking and European Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with Directives 2014/53/EU and
2011/65/ EU. Any radio operation limitations within EEA countries are identied in Appendix A of EU
Declaration of Conformity. The full text of the EU Declaration of Conformity is available at: zebra.com/doc.
EU Importer: Zebra Technologies B.V
Address: Mercurius 12, 8448 GX Heerenveen, Netherlands
Radio Transmitters
TThis device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation
of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
This guide applies to Model Number: LI4278 and LI4278A. All Zebra devices are designed to be
compliant with rules and regulations in locations they are sold and will be labeled as required.
Local language translations are available at the following website:
http://www.zebra.com/support
.
Any changes or modications to Zebra Technologies equipment, not expressly approved by
Zebra Technologies, could void the user’s authority to operate the equipment.
Bluetooth® Wireless Technology
This is an approved Bluetooth® product. For more information or to view End Product Listing, please visit
https://www.bluetooth.org/tpg/listings.cfm.
Wireless Device Country Approvals
Regulatory markings, subject to certication, are applied to the device signifying the radio(s) is/are approved
for use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, Europe 1,2. and
United Kingdom
Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at
http://www.zebra.com/doc.
Note1: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia,
Spain, Sweden and Switzerland.
Note 2: The use of RFID Devices have varying restrictions of use; please refer to the Zebra
Declaration of Conformity (DoC) for details.
Operation of the device without regulatory approval is illegal.
Health and Safety Recommendation
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury
follow the recommendations below. Consult with your local Health & Safety
Manager to ensure that you are adhering to your company's safety programs
to prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Radio Frequency Interference Requirements -FCC
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
LED Devices
Complies with IEC/EN60825-1:2001 & EN 62471: 2008 and IEC62471: 2006 Class 1 LED output.
LED Output – this device contains two LEDs for illumination and aiming.
Warnings for Use of Wireless Devices
Please observe all warning notices with regard to the usage of wireless devices.
Safety in Aircraft
Switch o your wireless device whenever you are instructed to do so by airport or airline sta. If your
device oers a ‘ight mode’
or similar feature, consult airline sta as to its use in ight.
Safety in Hospitals
Wireless devices transmit radio frequency energy and may aect medical electrical equipement.
Wireless devices should be switched o wherever you are requested to do so in hospitals, clinics or
health care facilities. These requests are designed to prevent possible interference with sensitive
medical equipment.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between
a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker.
These recommendations are consistent with independent research and recommendations by
Wireless Technology Research.
Persons with Pacemakers:
• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.
• Should not carry the device in a breast pocket.
• Should use the ear furthest from the pacemaker to minimise the potential for inter¬ference.
• If you have any reason to suspect that interference is taking place, turn OFF your device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to determine if the operation
of your wireless product may interfere with the medical device.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering human exposure to
electromagnetic elds from radio devices. For information on “International” human exposure to
electromagnetic elds refer to the Zebra Declaration of Conformity (DoC) at http://www.zebra.com/doc.
Batteries
Taiwan - Recycling
EPA (Environmental Protection Administration) requires dry battery producing or importing rms in
accordance with Article 15 of the Waste Disposal Act are required to indicate the recycling marks
on the batteries used in sales, giveaway or promotion. Contact a qualied Taiwanese recycler for proper
battery disposal.
Battery Information
Zebra rechargeable battery packs are designed and constructed to the highest standards
within the industry. However, there are limitations to how long a battery can operate or be stored before
needing replacement. Many factors aect the actual life cycle of a battery pack, such as heat, cold, harsh
environmental conditions and severe drops. When batteries are stored over six (6) months, some
irreversible deterioration in overall battery quality may occur. Store batteries at half of full charge in a dry,
cool place, removed from the equipment to prevent loss of capacity,
rusting of metallic parts and electrolyte leakage. When storing batteries for one year or longer, the charge
level should be veried at least once a year and charged to half of full charge. Replace the battery when
a signicant loss of run time is detected. Standard warranty period for batteries is 30 days,
regardless if the battery was purchased separately or included as part of the mobile computer or bar
code scanner.
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with Directive 2011/65/EU and
1999/5/EC or 2014/53/EU (2014/53/EU supersedes 1999/5/EC from 13th June 2017).
The full text of the EU Declaration of Conformity is available at the following internet address:
http://www.zebra.com/doc.
• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or
expose to water or other liquids, or expose to re, explosion, or other hazard.
• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked
vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to promptly dispose of used re-chargeable batteries.
• Do not dispose of batteries in re.
• Seek medical advice immediately if a battery has been swallowed.
Other Countries
Brazil
Declarações Regulamentares para LI4278
NOTA: A marca de certicação se aplica ao Equip. de Radiação Restrita, modelo LI4278.
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando
em caráter primário.” Para maiores consultas sobre ANATEL consulte o site: www.anatel.gov.br.
Mexico
Restrict Frequency Range to: 2.450 - 2.4835 GHz.
S. Korea
For a radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following two expressions
should be displayed:
.
Taiwan
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic
injury follow the recommendations below. Consult with your local
Health & Safety Manager to ensure that you are adhering to your
company’s safety programs to prevent employee injury.
• Reduce or eliminate repetitive motion.
• Maintain a natural position.
• Reduce or eliminate excessive force.
• Keep objects that are used frequently
within easy reach.
• Perform tasks at correct heights.
• Reduce or eliminate vibration.
• Reduce or eliminate direct pressure.
• Provide adjustable workstations.
• Provide adequate clearance.
• Provide a suitable working environment.
• Improve work procedures.
HELPFUL BAR CODES
ADD AN ENTER KEY To add an Enter key after scanned data, scan
<DATA><SUFFIX 1>
SCAN OPTIONS ENTER
1
2
3
(Carriage Return/Line Feed) all THREE bar codes in numerical order.
ADD A TAB KEY
7
0
0
9
1
2
3
4
5
To add a Tab key after scanned data, scan all THREE Enter key bar codes (left)
in numerical order then scan all FIVE bar codes below in numerical order.
Waste Electrical and Electronic Equipment (WEEE)
English: For EU Customers: All products at the end of their life must be returned
to Zebra for recycling. For information on how to return product, please go to:
http://www.zebra.com/weee.
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички
продукти трябва да се връщат на Zebra за рециклиране. За информация
относно връщането на продукти, моля отидете на адрес:
http://www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich
životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení
produktu najdete na webové stránce: http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når
de er udtjent. Læs oplysningerne om returnering af produkter på:
http://www.zebra.com/ weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer
Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας
ζωής τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για
περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος,
επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee στο Διαδίκτυο.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada
taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán
entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea
más información sobre cómo devolver un producto, visite:
http://www.zebra.com/weee.
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de
vie doivent être retournés à Zebra pour recyclage. Pour de plus amples
informations sur le retour de produits, consultez : http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del
rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il
riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito
Web: http://www.zebra.com /weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir
jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu
nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee.
Hrvatski: Za kupce u Europskoj uniji: Svi se proizvodi po isteku vijeka trajanja
moraju vratiti tvrtki Zebra na recikliranje. Informacije o načinu vraćanja proizvoda
potražite na web-stranici: www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi
būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti
gaminį, rasite: http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra
vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának
módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee
weboldalra.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu
tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif
għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van
hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg
http://www.zebra.com/weee voor meer informatie over het terugzenden van
producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji
nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu
produktów znajduj¹ siê na stronie internetowej http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser
devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver
o produto, visite: http://www.zebra.com/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de
funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre
returnarea produsului, accesaţi: http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí
doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o
vrátení výrobkov nájdete na: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe
vrniti podjetju Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite:
http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen
palauttamisesta on osoitteessa http://www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste
returneras till Zebra för återvinning. Information om hur du returnerar produkten
finns på http://www.zebra.com/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme
için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için
lütfen şu adresi ziyaret edin: http://www.zebra.com/weee.
Eurasian Customs Union
Евразийский Таможенный Союз
Данный продукт соответствует требованиям знака EAC.
Battery Safety Guidelines
• The area in which the units are charged should be clear of debris and combustible materials or
chemicals. Take particular care where the device is charged in a non commercial environment.
• Follow battery usage, storage, and charging guidelines found in the user's guide.
• Improper battery use may result in a re, explosion, or other hazard.
• To charge the mobile device battery, the battery and charger temperatures must be between +32 ºF
and +104 ºF (0 ºC and +40 ºC)
• Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may
present a risk of re, explosion, leakage, or other hazard. If you have any questions about the
compatibility of a battery or a charger, contact Zebra Global Customer Support Center.
• For devices that utilize a USB port as a charging source, the device shall only be connected to products
that bear the USB-IF logo or have completed the USB-IF compliance program.
• Do not disassemble or open, crush, bend or deform, puncture, or shred.
• Severe impact from dropping any battery-operated device on a hard surface could cause the battery
to overheat.
Tested to comply
with FCC Standards
FOR HOME OR OFFICE USE
United Kingdom
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with the Radio Equipment
Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical
and Electronic Equipment Regulations 2012.
Any radio operation limitations within UK are identified in Appendix A of UK Declaration of Conformity.
The full text of the UK Declaration of Conformity is available at: zebra.com/doc.
UK Importer: Zebra Technologies Europe Limited
Address: Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF
Ukraine
This equipment corresponds to requirements of the Technical Regulation No. 1057, 2008 on
restrictions as to the use of some dangerous substances in electric and electronic devices.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
For Australia Only
This warranty is given by Zebra Technologies Asia Pacic Pte. Ltd., 71 Robinson Road, #05-02/03, Singapore
068895, Singapore. Our goods come with guarantees that cannot be excluded under the Australia Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
Zebra Technologies Corporation Australia’s limited warranty above is in addition to any rights and remedies
you may have under the Australian Consumer Law. If you have any queries, please call Zebra Technologies
Corporation at+65 6858 0722. You may also visit our website: http://www.zebra.com for the most updated
warranty terms.
-
1
