Yamaha DD-50 de handleiding

Categorie
Muziek drums
Type
de handleiding

Deze handleiding is ook geschikt voor

2
DIGITAL
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
DEUTSCHFRANÇAIS
ESPAÑOL
ENGLISH
SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply (adaptor). DO
NOT connect this product to any power supply or adaptor other than one
described in the manual, on the name plate, or specifically recommended
by Yamaha.
This product should be used only with the components supplied or; a cart,
rack, or stand that is recommended by Yamaha. If a cart, etc., is used,
please observe all safety markings and instructions that accompany the
accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct at the
time of printing. However, Yamaha reserves the right to change or modify
any of the specifications without notice or obligation to update existing
units.
This product, either alone or in combination with an amplifier and head-
phones or speaker/s, may be capable of producing sound levels that could
cause permanent hearing loss. DO NOT operate for long periods of time
at a high volume level or at a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period before
damage occurs.
NOTICE:
Service charges incurred due to a lack of knowledge relating to how a
function or effect works (when the unit is operating as designed) are not
covered by the manufacturer’s warranty, and are therefore the owners
responsibility. Please study this manual carefully and consult your dealer
before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and environ-
mentally friendly. We sincerely believe that our products and the produc-
tion methods used to produce them, meet these goals. In keeping with
both the letter and the spirit of the law, we want you to be aware of the
following:
Battery Notice:
This product MAY contain a small non-rechargeable battery which (if
applicable) is soldered in place. The average life span of this type of
battery is approximately five years. When replacement becomes neces-
sary, contact a qualified service representative to perform the replace-
ment.
This product may also use “household” type batteries. Some of these
may be rechargeable. Make sure that the battery being charged is a
rechargeable type and that the charger is intended for the battery being
charged.
When installing batteries, do not mix batteries with new, or with batteries
of a different type. Batteries MUST be installed correctly. Mismatches or
incorrect installation may result in overheating and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all batter-
ies away from children. Dispose of used batteries promptly and as regu-
lated by the laws in your area. Note: Check with any retailer of household
type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some reason
its useful life is considered to be at an end, please observe all local, state,
and federal regulations that relate to the disposal of products that contain
lead, batteries, plastics, etc. If your dealer is unable to assist you, please
contact Yamaha directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the product. The model
number, serial number, power requirements, etc., are located on this
plate. You should record the model number, serial number, and the date
of purchase in the spaces provided below and retain this manual as a
permanent record of your purchase.
Model
Serial No.
Purchase Date
92-BP
PLEASE KEEP THIS MANUAL
IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in
this manual, meets FCC requirements. Modifications not expressly ap-
proved by Yamaha may void your authority, granted by the FCC, to use the
product.
IMPORTANT:
When connecting this product to accessories and/or another product use
only high quality shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to follow instructions
could void your FCC authorization to use this product in the USA.
NOTE:
This product has been tested and found to comply with the requirements
listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance
with these requirements provides a reasonable level of assurance that your
use of this product in a residential environment will not result in harmful
interference with other electronic devices. This equipment generates/uses
radio frequencies and, if not installed and used according to the instructions
found in the users manual, may cause interference harmful to the operation
of other electronic devices.
Compliance with FCC regulations does not guarantee that interference will
not occur in all installations. If this product is found to be the source of
interference, which can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the following meas-
ures:
Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker or fuse)
circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If
the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-
axial type cable.
If these corrective measures do not produce satisfactory results, please
contact the local retailer authorized to distribute this type of product. If you
can not locate the appropriate retailer, please contact Yamaha Corporation
of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
• This applies only to products distributed by Yamaha Corporation of
America.
FCC INFORMATION (U.S.A.)
The serial number of this product may be found on the bottom
of the unit. You should note this serial number in the space
provided below and retain this manual as a permanent record of
your purchase to aid identification in the event of theft.
Model No. DD-50
Serial No.
Entsorgung leerer Batterien
(nur innerhalb Deutschlands)
Leisten Sie einen Beitrag zum Umweltschutz. Verbrauchte
Batterien oder Akkumulatoren dürfen nicht in den Hausmüll. Sie
können bei einer Sammelstelle für Altbatterien bzw. Sondermüll
abgegeben werden. Informieren Sie sich bei Ihrer Kommune.
1
Congratulations!
Thank you for purchasing the Yamaha DD-50. The DD-50 has been developed to
act and play like a drum set but with greater ease. Before you use the instru-
ment, we recommend you to read through this manual.
Your DD-50 will give you years of playing pleasure if you follow the simple rules given below:
YAMAHA is not responsible for damage caused by improper handling or operation.
Taking Care of Your DD-50
Location
Do not expose the instrument to the following
conditions to avoid deformation, discoloration, or
more serious damage.
Direct sunlight (e.g. near a window).
High temperatures (e.g. near a heat source,
outside, or in a car during the daytime).
Excessive humidity.
Excessive dust.
Strong vibration.
Power Supply
Turn the power switch OFF when the instru-
ment is not in use.
An AC adaptor, if used (the DD-50 runs from
either batteries or an optional AC adaptor),
should be unplugged from the AC outlet if
the instrument is not to be used for an ex-
tended period of time.
Unplug the AC adaptor during electric
storms.
Avoid plugging the AC adaptor into the same
AC outlet as appliances with high power
consumption, such as electric heaters or
ovens. Also avoid using multi-plug adaptors
since these can result in reduced sound
quality, operation errors, and possibly dam-
age.
Turn Power OFF When Making
Connections
To avoid damage to the instrument and other
devices to which it is connected, turn the
power switches of all related devices OFF
prior to connecting or disconnecting cables.
Handling and Transport
Never apply excessive force to the controls,
connectors or other parts of the instrument.
Always unplug cables by gripping the plug
firmly, not by pulling on the cable.
Disconnect all cables before moving the
instrument.
Physical shocks caused by dropping, bump-
ing, or placing heavy objects on the instru-
ment can result in scratches and more serious
damage.
Cleaning
Clean the cabinet and panel with a dry soft
cloth.
A slightly damp cloth may be used to remove
stubborn grime and dirt.
Never use cleaners such as alcohol or thinner.
Avoid placing vinyl objects on top of the
instrument (vinyl can stick to and discolor the
surface).
Electrical Interference
This instrument contains digital circuitry and
may cause interference if placed too close to
radio or television receivers. If this occurs,
move the instrument further away from the
affected equipment.
Data Backup
Custom data and some settings (see page 21)
will be retained in memory even if the power
switch is turned OFF as long as an AC power
adaptor is connected or batteries are installed.
Service and Modification
The DD-50 contains no user serviceable parts.
Opening it or tampering with it in anyway can
lead to irreparable damage and possibly
electric shock. Refer all servicing to qualified
YAMAHA personnel.
2
Table of Contents
Setting up the DD-50 3
Power Supply ................................................3
When Using headphones
(About the PHONES/AUX OUT jack)............3
Control Panel 4
Connecting the foot pedals 1/2 ..................... 5
Supplied Accessories ...................................5
Playing the Demo Song 6
MASTER VOLUME.......................................6
SONG VOLUME...........................................6
Play the Pads/Pedals 7
Pad Names ................................................... 7
Assigning a Drum Kit to the
Pads and Pedals ...........................................8
Assigning a Voice to Individual
Pads and Pedals (“CU” Custom Kit) .............8
REVERB ON/OFF ........................................9
Select the REVERB Depth ............................9
CLICK ON/OFF.............................................9
Try Recording 15
RECORD .................................................... 15
Playback .....................................................15
Using the MIDI/Utility Mode 16
Data 23
Drum Voice List ........................................... 23
Drum Kit List ...............................................24
Song List..................................................... 26
Drum Map ...................................................27
Specifications..............................................28
MIDI Implementation Chart......................... 29
What is MIDI? ............................................. 16
What you can do with MIDI......................... 16
Enter/Exit the MIDI/Utility Mode.................. 17
Setting the Clock.........................................17
Local ON/OFF.............................................18
Setting the MIDI Transmit Channel ............. 18
Setting the MIDI Note Number.................... 20
Initialize 21
Troubleshooting 22
Data Backup .............................................. 21
Playing a SONG 10
Selecting a SONG ......................................10
Auto Kit Select ON/OFF Setting..................10
Adjusting the TEMPO .................................11
Play along with a SONG 12
TRACK ON/OFF ......................................... 12
TAP START .................................................12
BREAK........................................................13
A-B REPEAT ...............................................14
Cancel the Repeat Points ............................ 14
3
Power Supply
Your DD-50 will run either from batteries or an optional power adaptor. Follow the instructions below
according to the power source you intend to use.
Setting up the DD-50
Using an AC-Adaptor (sold separately)
Installing Batteries
Connect the optional power adaptor (Yamaha
PA-3 or PA-3B) to the DC IN 10-12V jack located
on the unit’s left side panel, and plug the AC power
adaptor into an AC power outlet.
3
Close the battery compartment cover securely.
1
Open the battery compartment cover on the
underside of the DD-50.
2
Insert six “C” size, R14, SUM-2 or equivalent
batteries. When inserting the batteries, be
careful to follow the polarity markings in the
illustration.
Do not attempt to use an AC adaptor other than the
PA-3 or PA-3B. Use of an incompatible adaptor may
result in the instrument becoming hot or, irreparable
damage to the DD-50. It may also result in fire. If the
instrument is damaged due to use of an incompatible
adaptor, YAMAHA is not responsible for the damage.
When Using Headphones
(About the PHONES/AUX OUT Jack)
An optional set of stereo headphones (such as
the Yamaha HPE-150 or HPE-3) can be connected
to the PHONES/AUX OUT jack located on the
side panel. When a pair of headphones is con-
nected to the jack, the DD-50’s internal speakers
will switch off automatically, perfect for private
practice or late night playing. If you want to use an
external sound system, the headphone jack can
also be used to connect the DD-50 to a stereo
system or mixing console. (Use a standard plug n
pin plug adaptor to connect the DD-50 to a stereo
system.)
* Turn the power OFF on all equipment before
making any connections.
Power will be automatically drawn from the AC
adaptor if an optional AC adaptor is connected while
batteries are installed in the instrument.
It is recommended that you replace worn batteries as
soon as possible. When battery voltage drops, the
DD-50s display will dim and/or the sound will become
distorted. When this occurs, replace the batteries with
a complete set of six new batteries of the same type.
NEVER mix old and new batteries, different types of
batteries (alkaline, magnesium, etc.), batteries by
different makers, or batteries from the same maker
but of different types.
Misuse may cause the instrument to become hot,
result in fire, or battery leakage.
Also, to prevent damage due to battery leakage,
remove all of the batteries from the instrument when it
is not to be used for an extended period of time.
Batteries left in an unused instrument will also loose
their power over time.
O
P
E
N
O
P
E
N
AC power socket
PA-3/
PA-3B
DC IN 10 - 12V
4
Control Panel
*
(
! CLICK button .................................................9
@ DIAL...............................................................8
# START/STOP button....................................10
$ BREAK/TAP START button....................12, 13
% A-B REPEAT button.....................................14
^ DEMO button.................................................6
& Drum Pads (x 7) ............................................7
Front Panel Page
1 POWER ON/OFF Switch...............................6
2 SONG VOLUME buttons ...............................6
3 PAD ASSIGN button ................................8, 19
4 KIT ASSIGN button .................................8, 20
5 SONG button ...............................................10
6 TEMPO button .............................................11
7 Display ...........................................................8
8 MASTER VOLUME buttons...........................6
9 REVERB button.............................................9
0 Track buttons
DRUM 1 button ......................................12, 17
DRUM 2 button ......................................12, 18
BASS button ................................................12
BACKING button....................................11, 12
DC IN 10 - 12V
PHONES /
AUX OUT
88
BEAT
TEMPOSONG
CLICKBACKINGBASS
DRUM 2DRUM 1
POWER
OFF ON
REVERB
PAD KIT
ASSIGN
PRESET TEMPO
MASTER VOLUME
SONG
VOLUME
1
2
3
4
5
6
7
9
0
!
8
&
5
Control Panel
)
q
Side Panel (Left)
* DC IN 10-12V (AC Adaptor) Jack ..................3
( PHONES/AUX OUT Jack ..............................3
Side Panel (Right)
) MIDI IN/MIDI OUT Terminals .......................16
q PEDAL 1/2 Jacks...........................................5
@
MIDI IN
MIDI OUT
PEDAL 1
PEDAL 2
DEMO DD-50
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
R
E
C
.
#
$
%
^
Connecting the Foot Pedals (1/2)
The supplied foot pedals can be connected to the
DD-50 to similarly play the drum set’s hi-hat
pedal or bass drum voices or they can also be
assigned to play other voices as well.
Do not press the pedal while connecting
it to the DD-50 or while turning on the
power. (Connecting in this manner with
the power on, the pedals function may
be reversed.)
Supplied Accessories
Foot Pedal x 2
Drum Stick x 2
Owners Manual
6
Playing the Demo Song
1 Turn on the power
Turn the [POWER] switch ON.
To give you idea of the DD-50s possibilities, it comes with a demonstration song. To playback
the demo song:
POWER
OFF ON
Press the [DEMO] button, the demo song will start playback.
2 Start the Demo Song
MASTER VOLUME
Small Large
SONG
VOLUME
Small Large
MASTER VOLUME
The overall volume level of the DD-50 is controlled by two [MAS-
TER VOLUME] buttons (10 volume levels L0-L9).
Press the large [MASTER VOLUME] button to increase the
overall volume by one level. Press the small [MASTER VOL-
UME] button to decrease the overall volume one level. Holding
down either of the buttons increases or decreases the volume level
rapidly.
SONG VOLUME
The song’s volume level is controlled by the two [SONG VOL-
UME] buttons (10 volume levels L0-L9). (Demo Song, Song see
page 10)
The SONG VOLUME can be used to adjust the balance between
the song accompaniment and your own performance on the pads.
Press the large [SONG VOLUME] button to increase the song
volume by one level. Press the small [SONG VOLUME] button to
decrease the song volume by one level. Holding either of the
buttons increases or decreases the song volume level rapidly.
DEMO
L0 < L5 > L9
Small < Volume Level > Large
*When the MASTER VOLUME is set to L0, the songs volume is silenced.
L0 < L5 > L9
Small < Volume Level > Large
* When the SONG VOLUME is set to L0, the songs volume is silenced.
3 Stop the Demo Song
To stop playback, press either the [DEMO] button again or the
[START/STOP] button.
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
DEMO
7
Play the Pads/Pedals
Strike the pad with the supplied drum sticks to play the drum voices. Drum Kit 00 is auto-
matically chosen whenever the power is turned on (see the Drum Kit List page 24).
Striking the pads with different force results in relatively loud or soft sounds accordingly.
Loudness of the sound may vary according to which part of the pad is struck.
Ex. shown, Drum Kit 00 : Standard 1
Pad 3
18: Mid Tom (High)
Pedal 1
1: Bass Drum (Mid)
Pedal 2
34: Hi-Hat Pedal
A hi-hat sound is assigned to the Small Pad 3
(Drum Kit 00). Striking the Small Pad 3while
pressing on Pedal 2 produces a closed hi-hat
sound. Striking the pad without pressing the pedal
produces an open hi-hat sound.
The bass drum voice is control-
led by pressing Foot Pedal 1.
Use Foot Pedal 2 to control the
Hi-hat. (This is in the case of
Drum Kit 00.)
Small Pad 3
34: Hi-Hat
Close/Open
Pad 4
20: Low Tom (High)
Pad 1
8: Snare Drum (High)
Pad 2
16: High Tom (High)
Small Pad 1
38: Crash
Cymbal (High)
Small Pad 2
39: Ride Cymbal
Pad Names
8
Assigning a Drum Kit to the Pads and Pedals
Play the Pads/Pedals
The DD-50 allows you to choose from 20 different Drum Kits (00-19 : see the “Drum Kit List”
page 24) quickly and easily. 20 of the kits have preset voice combinations that will be set to the pads
and pedals when the kit is selected. Select some different kits and try playing them.
The DD-50 also has one Custom Drum Kit allowing you to assign the desired voices to the seven
pads or two pedals (see “Assigning a Voice to Individual Pads and Pedals” below).
1 Press the [KIT ASSIGN] button
10
BEAT
ASSIGN
PAD KIT
2 Select a Drum Kit Number
Turn the DIAL to select a Drum Kit number. Drum Kit numbers will
increase as the DIAL is turned to the right (clockwise), and decrease as
the DIAL is turned to the left (counter-clockwise).
Drum Kit number 00 is normally selected when the power is turned ON. How-
ever, if Auto Kit Select is set to OFF, the last Drum Kit selected before turning the
power OFF, is automatically selected when the power is turned ON. (See Auto
Kit Select ON/OFF Setting on page 11)
The CU Drum Kit is the Custom Kit. Changes made to any one of the preset
drum kits will be saved here. (See Assigning a Voice to Individual Pads and
Pedals below.)
Assigning a Voice to Individual Pads and Pedals
(“CU” Custom Kit)
The DD-50 contains a total of 75 high quality drum sounds (see the “Drum Voice List” page 23)
that can be assigned to each of the 7 drum pads and 2 foot pedals. Try assigning some different voices
to the “CU” Custom Drum Kit.
Any change made to one of the preset drum kits will automatically be saved in the
CU Custom Drum Kit.
Both the Custom and 00 drum kit contents are the same until modified (see the
Drum Kit List page 24).
1 Press the [PAD ASSIGN] button
25
BEAT
ASSIGN
PAD KIT
2 Select a Pad/Pedal
10
BEAT
00 19 CU
Press the [PAD ASSIGN] button, Pad 1’s currently assigned voice
number is shown in the display.
Strike any pad one time (or press a pedal), that pad’s/pedal’s currently
assigned voice number is shown in the display.
Pressing the [KIT ASSIGN] button, the button’s lamp will light and
the currently selected Drum Kit number appears on the display.
9
Play the Pads/Pedals
3 Select a Voice Number
You can select the voice by repeatedly striking the pad, repeatedly
pressing the pedal (while listening to the voice) or by turning the DIAL.
Striking the pad or pressing the pedal to select a voice.
First, select a pad or pedal by striking or pressing it once. After the
pad/pedal has been selected, every time the pad is struck or a pedal
is pressed, voice numbers will increase by a value of one (1).
Using the DIAL to select a voice.
Turn the DIAL to the right (clockwise), and voice numbers will
increase. Turn the DIAL to the left (counter-clockwise), and voice
numbers will decrease.
4 Play the Pads and Pedals
After assigning a voice to the desired pad/pedal, press the [SONG]
button. You can now play the voice you have assigned to the pad/pedal.
Repeat the previous steps for any or all of the DD-50’s pads and pedals
and try playing your own original drum kit.
PRESET TEMPO
SONG TEMPO
REVERB ON/OFF
Different depths of the DD-50’s reverb effect can be selected to add to
the DD-50’s overall sound.
To turn on the reverb effect, press the [REVERB] button. To turn off
the reverb effect, press the [REVERB] button again.
Select the REVERB Depth
When the reverb has been turned on, press and hold the [REVERB]
button, turn the DIAL to select one of the three reverb depths that
appear in the display. [r1], [r2], [r3].
Selecting [r3] adds the most reverb depth to the effect.
REVERB
REVERB
r1
BEAT
0 1 ........... ........... ...........73 74
@
0 1 ........... ........... ...........73 74
@
CLICK ON/OFF
The DD-50’s CLICK feature produces a metronome click to make the
tempo easier to follow and improve your timing while playing the pads.
To hear the metronome click, press the [CLICK] button. To turn the
click off, press the button once again.
CLICK
REVERB Depth data is not transmitted or received via MIDI.
10
Playing a SONG
The DD-50 features 100 different songs that can be used to provide accompaniment (see the
Song List page 26). Select one of the songs and have a listen.
Selecting a SONG
1 Press the [SONG] button
Press the [SONG] button, its LED indicator will light, and the cur-
rently selected song number will appear in the display.
2 Use the DIAL to select a song number
Song numbers will increase in value as the DIAL is turned to the right
(clockwise) and decrease as the DIAL is turned to the left (counter-
clockwise). (See the “Song List” on page 26)
Song number 00 is automatically selected whenever the power is turned ON.
With the Auto Kit Select turned on, selecting a song will also automatically select
the best suited Drum Kit for that song (see Auto Kit Select ON/OFF Setting
below).
Song numbers are arranged according to their complexity. Smaller numbers are
easier to play than larger numbers.
PRESET TEMPO
SONG TEMPO
10
BEAT
3 Press the [START/STOP] button
Press the [START/STOP] button, after a two-measure count-in (or one
measure count-in), the song will start playback.
As the song is playing, the Song’s current measure will be shown in the
display. Try playing the pads and pedals along with the song.
To stop playback of the song, press the
[START/STOP]
button once
again.
You can also use the TAP START function to start songs (see page 12).
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
The DD-50’s songs consists of two types, loop type and sequence
type (see the “Song List” page 26).
Sequence type songs will automatically stop when the song reaches its
end.
Loop type songs will continuously play from the time the [START/
STOP] button is initially pressed, until the button is pressed once again.
Auto Kit Select ON/OFF Setting
1 Setting the Auto Kit Select to ON or OFF
Press the [DEMO] and [START/STOP] buttons simultaneously to
enter the MIDI/Utility Mode .
The Auto Kit Select function automatically selects the best matching drum kit to the selected song.
You can deactivate this feature by setting the Auto Kit Select to OFF.
Sequence
Loop
00 01 . . ...99 CU
11
2 Select ON or OFF
Press the [BACKING] button and the current ON/OFF setting will
appear in the display. Turn the DIAL to the right (clockwise) to activate
the Auto Kit Select (on). Turn to the left (counter-clockwise) to deactivate
the Auto Kit Select (oF).
Playing a SONG
Adjusting the TEMPO
1 Press the [TEMPO] button
2 Set the Tempo
The song tempo can be set anywhere from 40 to 280 beats per minute. As tempo numbers increase,
the tempo will become faster.
Press the [TEMPO] button, the current tempo value (40-280) appears
in the display.
Use the DIAL to select the TEMPO. Turn the DIAL to the right
(clockwise) to increase Tempo values, turn to the left (counter-clockwise)
to decrease Tempo values.
(Tempo values will cycle to 40 or 280 then stop.)
PRESET TEMPO
SONG TEMPO
50
BEAT
3 Exit the Tempo setting mode
Press the [SONG] button to exit from the Tempo setting mode.
When both the SONG and TEMPO buttons are pressed simultaneously, the
preset tempo of the currently selected song will automatically applied.
PRESET TEMPO
SONG TEMPO
90
BEAT
Tempo Display Comment
q=90 90
q=110 ,10 100th digit (1) is shown as a single dot
q=250 ,5,0 100th digit (2) is shown as two dots
1st beat 2nd beat 3rd beat 4th beat
,9,0 9,0 9,0 9,0
About the Beat Indicator
During song playback, the two beat lamps in the display will flash
in a specific pattern to assist you in keeping the beat.
q= 90 beats per minute.
on
BEAT
BACKING
oF
BEAT
3 Exit the Auto Kit Select
The Auto Kit Select is automatically set to OFF when the MIDI Transmit Note is
changed to another channel.
Press the [DEMO] and [START/STOP] buttons simultaneously once
again to exit the MIDI/Utility Mode .
40 41 ,,7,9 ,8,0
12
Play along with a SONG
TRACK ON/OFF
Use the pads and pedals to play along with a song accompaniment.
The DD-50’s song accompaniment consists of 4 tracks; Drum 1/2, Bass, and Backing tracks.
The DD-50 can play a total of 28 notes simultaneously. That includes notes
produced by song accompaniment, pads, foot pedals, and note data received
through the MIDI IN jack.
Pressing a Track button ([DRUM 1], [DRUM 2], [BASS], [BACK-
ING]) will mute (turn off the sound) the corresponding track and its
indicator lamp will turn off.
Muting DRUM 1 and DRUM 2 tracks allows you to practice your
playing technique in Karaoke style (Minus One).
DRUM 1 Main Drum track
DRUM 2 Main Percussion track
BASS Bass track
BACKING Main Backing Track
DRUM 1 DRUM 2 BASS BACKING
TAP START
The TAP START function allows you to set the song’s overall tempo as well as start the accompani-
ment. The accompaniment will playback at the tempo with which the pads are struck or the pedals are
pressed.
1 Press the [BREAK/TAP START] button
Press the [BREAK/TAP START] button when the song stops, its
indicator will flash and the DD-50 is in Tap Start standby mode.
To cancel the Tap Start mode, simply press the [BREAK/TAP
START] button once again (the indicator will turn off).
2 Tap Start
In the case of a song in 4/4, strike any pad or press any pedal four
times, the accompaniment will start at the desired tempo.
The number of times needed to strike the pad will change according to the
following time signatures; 5/4, 5 times; 4/4, 4 times; 3/4, 3 times; 6/8, 2 times.
3 Stop the Song Playback
To stop playback, press the [START/STOP] button.
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
13
BREAK
1
During song playback, press the BREAK/TAP START button
With the BREAK function, you can liven up songs by adding your own solos or fills, whenever you
want. Striking a pad while in the BREAK mode, the song’s accompaniment will be muted until the end
of the measure you have finished your fill or solo in.
During song playback, press the [BREAK/TAP START] button, its
indicator will flash and the DD-50 is in BREAK standby mode.
To cancel the Break mode, simply press the [BREAK/TAP START]
button once again (its indicator will turn off).
Play along with a SONG
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
3 Exit the BREAK mode
The DD-50 returns to the BREAK standby mode when the BREAK
measure is completed.
To exit the BREAK mode, press the [BREAK/TAP START] button.
The BREAK mode is also exited when the song is stopped.
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
2 Break
Strike any pad and the accompaniment will mute until the end of the
measure you played in. You can play a drum fill or drum solo during this
break.
14
A-B REPEAT
1 To set the A (start repeat) point
3 Stop the A-B REPEAT mode
When the song playback has reached the start of the section you want
to practice, press the [A-B REPEAT] button and the “A” repeat point is
set. An “A” will appear in the display.
If you want to practice a particular section of a song, you can specify that section’s “A” (start
repeat) and “B” (end repeat) points. The accompaniment will continuously repeat between points
“A” and “B” allowing you to practice between those points for as long as you like.
Press the [START/STOP] button and the song accompaniment will stop.
“Ab” will appear in the display indicating the A-B REPEAT mode is
still engaged.
Press the [START/STOP] button once again and the accompaniment
will again repeat between the set points.
Play along with a SONG
2 To set the B (end repeat) point
A
BEAT
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
Ab
BEAT
Ab
BEAT
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
Cancel the Repeat Points
To cancel the A-B REPEAT, press the [A-B REPEAT] button
during playback or while playback is stopped, the A-B REPEAT
mode will be canceled (the A-B REPEAT points will also be
canceled) and normal playback of the accompaniment will con-
tinue.
When the song playback has reached the end point of the section you
want to practice, press the [A-B REPEAT] button once again and the A
to B repeat points are set, “b” appears in the display. “Ab” will appear in
the display and after a one measure count-in the repeat playback will
start. The current measure number will appear in the display during the
repeat playback.
The A-B REPEAT start and end points can only be set in measure steps.
Songs consist of two types; loop type and sequence type (see the Song List on
page 26). When setting the A-B points for sequence songs, set both points
before the end of the song. The set A point will be canceled if the B point is
not set before the end of the song.
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
Selecting another song will cancel any previously set A-B REPEAT points.
In the case of a loop type song, it is possible, for example, to set the A point at
measure 10 and set the B point at measure 3 (after the song has looped back
to the beginning).
B
3
A
10
15
Try Recording
Playback
The DD-50s Custom Song feature (song number CU) allows you to record and playback
one original song (600 notes approximately).
The recorded Custom Song (song number “CU”) can be played back in the same manner as any
song (song numbers “00”-”99”).
CU
BEAT
Song number “CU” follows Song number “99” (or prior to “00”).
The A-B REPEAT mode (see 14 page) cannot be used in the Custom Song Mode.
RECORD
1 Prepare to Record
Select the desired song, drum kit, tempo, track on/off setting, and
reverb settings.
2 Start Recording
P
ress both the [START/STOP] and [BREAK/TAP START] buttons
simultaneously, after a count-in (the indicator will flash) recording will start.
Data will not be recorded during the 2 measure count-in.
Press the BREAK/TAP START button during the 2 measure count-in to enter Tap
Start Record Standby mode (see page 12).
Press the CLICK button to cancel the metronome during recording.
3 Stop Recording
To stop recording, press the [START/STOP] button.
Any previously recorded data will be replaced with new data.
If the memory becomes full while recording is in progress, FL will appear in the
display and recording will automatically stop.
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
* MIDI data cannot be recorded to the memory.
oo
BEAT
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
Data that can be recorded in the Custom Song Mode.
• Drum pad and pedal data.
• Song data (the number cannot be changed while in the RECORD Mode).
• Track ON/OFF settings.
• Tempo setting (The tempo cannot be changed while in the RECORD mode).
• Song Volume setting.
• Reverb ON/OFF setting.
• Break ON/OFF setting.
16
Using the MIDI/Utility Mode
The MIDI IN and MIDI OUT terminals, located on the DD-50s right side panel, offer broad-
ened musical possibilities through use of MIDI. But, what is MIDI? What can you do with
MIDI? How can you use MIDI with the DD-50? Here are a few examples.
MIDI Keyboards
MIDI IN
MIDI OUT
DD-50
What you can do with MIDI
What is MIDI?
MIDI stands for Musical Instrument Digital Interface. MIDI is a world wide standard that
makes it possible for various electronic musical instruments and other devices, such as computers, to
“communicate” with each other. For example, by connecting a MIDI tone generator to the DD-50’s
MIDI OUT terminal, you can play the tone generator’s voices from the DD-50’s pads and pedals.
The DD-50 is equipped with two types of MIDI terminals, both are
located on the right side panel.
MIDI IN
Data transmitted from other MIDI instruments via MIDI, is re-
ceived at this terminal.
MIDI OUT
Data produced by the DD-50, is transmitted to other MIDI instru-
ments via MIDI from this terminal.
Use a MIDI cable (option), obtainable at your local music dealer, when making
MIDI connections.
Never use MIDI cables longer than 15 meters in length. (Cables longer than 15
meters can pick up noise which can cause data errors.)
Connect the DD-50s MIDI OUT jack to a MIDI keyboards
(or tone generators) MIDI IN jack.
This setup allows you to use the DD-50’s pads to control another
MIDI instrument. Playing the DD-50’s pads will result in the other
MIDI instrument’s voice sounding simultaneously, creating a
thicker overall sound.
Connect the DD-50s MIDI OUT jack to a MIDI sequenc-
ers MIDI IN terminal.
Data produced by the DD-50 (Key ON and Velocity data) can be
recorded to a MIDI sequencer. Data can also be recorded to com-
puters or other sequencers as well.
Connect the DD-50s MIDI IN terminal to a MIDI key-
boards MIDI OUT terminal.
In this setup the DD-50 can be used as a tone generator and its
voices can be played from a MIDI keyboard. Using a keyboard as a
controller, it is possible to play DD-50 voices that are not assigned
to the pads/pedals.
Connect the DD-50s MIDI IN terminal to a MIDI sequenc-
ers MIDI OUT terminal.
The sequencers data can be used to drive the DD-50’s sounds.
MIDI OUT
MIDI IN
MIDI Keyboard
MIDI IN
MIDI OUT
DD-50
MIDI IN
MIDI OUT
DD-50
Sequencer
Sequencer
MIDI IN
MIDI OUT
DD-50
Yamaha
MIDI Data Filer
MDF2 etc.
17
Enter/Exit the MIDI/Utility Mode
To enter the MIDI mode, press the [START/STOP] and [DEMO]
buttons simultaneously, an “
mm
” will appear in the display to indicate the
MIDI mode.
Setting the Clock
Connecting the DD-50, by MIDI cable, to an external MIDI device, such as a sequencer, time based
functions (song playback, etc.) must be controlled by the internal clock (I) or an external clock (E).
When the internal clock (I) is enabled, timing will be controlled by the DD-50’s internal clock. When
an external clock (E) selected, time based functions will be controlled by the sequencers or compu-
ters clock.
1 Display the clock setting
After entering the MIDI/Utility mode, press the [DRUM 1] button to
see the current setting for the MIDI clock.
2 Set the Clock to External or Internal
To set the clock to “E” (external), turn the DIAL to the right (clock-
wise). To set the clock to “I” (internal), turn the DIAL to the left (counter-
clockwise).
3 Exit the MIDI/Utility mode
After the clock is set, exit the MIDI/Utility mode.
The default MIDI clock setting is I (internal).
Using the MIDI/Utility Mode
DEMO
BREAK/
TAPSTART
START/
STOP
A-B
REPEAT
REC.
mm
BEAT
I
BEAT
DRUM 1
E
BEAT
I (Internal)
The DD-50’s clock is used as the timing clock.
E (External)
The external clock is used as the timing clock (If the clock is set to
external without being connected to another MIDI device, the DD-
50’s Song Play or Demo functions will not respond).
To exit the MIDI mode, once again press the [START/STOP] and
[DEMO] buttons simultaneously, the MIDI mode will be exited and the
DD-50 will return to its normal play mode.
Pads and pedals do not sound while in the MIDI/Utility mode.
18
Local ON/OFF
Setting the Local ON/OFF determines whether or not the internal voices respond to the notes you
play on the DD-50’s pads. Setting this to OFF disconnects the DD-50’s pads from the voices. How-
ever, data produced by the DD-50 is transmitted via the MIDI OUT terminal.
1 Display the Local On/Off Setting
After entering the MIDI/Utility mode, press the [DRUM 2] button and
the current Local ON /OFF setting will appear in the display.
2 Set the Local On/Off
To set to “on” (Local ON), turn the DIAL to the right (clockwise), to
set to “oF”(Local OFF), turn the DIAL to the left (counter-clockwise).
3 Exit the MIDI/Utility mode
After setting the Local ON/OFF, exit the MIDI/Utility mode.
Regardless of the Local ON/OFF setting, the DD-50s performance data
(including demo song data) is always sent to the MIDI OUT terminals for
transmission to external MIDI devices.
The default Local ON/OFF setting is ON (Local ON).
Using the MIDI/Utility Mode
on
BEAT
oF
BEAT
DRUM 2
on (Local ON)
The internal voices will be played and controlled by the DD-50 and
its pads. Data received via MIDI will also be played by the DD-50.
oF (Local OFF)
Striking the pads will not produce any sound from the voices.
However, data received via MIDI will be played by the DD-50.
Setting the MIDI Transmit Channel
Each of the pads/pedals (a total of 9) can be assigned to transmit on any of the 16 MIDI channels,
or turned off (indicated as “oF” in the display). Also, song transmit channels are as shown below:
Transmit Channel Default
Pad/Pedal 1-16 10
Drum (Song) 9, 10 9
Bass (Song) 11 (fixed)
Backing (Song) 12-15 (fixed)
Pad/Pedal
10, 16 16
(Custom Song)
19
Using the MIDI/Utility Mode
Setting the MIDI Transmit Channel . Drum (Song)
Song performance data is transmitted on channel 9. You can change this transmit channel to chan-
nel 10 by using the procedure below:
> First enter the MIDI/Utility mode by pressing both the [START/
STOP] and [DEMO] buttons simultaneously. Press the [SONG]
button and the currently selected transmit channel will be displayed.
> Turning the DIAL, you can select either channel 9 or channel 10.
After making a selection, exit the MIDI/Utility mode by pressing
both the [START/STOP] and [DEMO] buttons simultaneously
once again.
Depending upon the setting of the Drum’s (Song) MIDI Transmit Channel, the
MIDI Transmit Channel for the Pads/Pedals (Custom Song) will automatically
change as follows:
10
BEAT
2 Select a pad to be assigned a MIDI Transmit Number
To select the pad you want to assign a MIDI transmit channel to, strike
the pad. That pad’s currently selected MIDI transmit channel will appear in
the display.
3 Set the MIDI Transmit Channel Number
Turning the DIAL to the right (clockwise), MIDI transmit channel
numbers will increase.
You can also select the MIDI transmit channel by striking the pad. Every time the
pad is struck the MIDI transmit channel number will increase by 1.
4 Exit the MIDI/Utility mode
After all pads/pedals have been assigned MIDI transmit channels, exit
the MIDI/Utility mode.
For further information on what type of data is transmitted via MIDI, see the MIDI
Implementation Chart (page 29), and try out the DD-50s advanced MIDI features.
10
BEAT
1 Display the MIDI Transmit Channel Number
After entering the MIDI/Utility mode, press the [PAD ASSIGN]
button and the current Pad 1 transmit channel will be displayed.
10
BEAT
ASSIGN
PAD KIT
10
BEAT
9
BEAT
Display 9 10
Drum (Song) 9 10
Pad/Pedal
16 10
(Costom Song)
20
Setting the MIDI Note Number
Using the MIDI/Utility Mode
After entering the MIDI/Utility mode, press the [KIT ASSIGN]
button, the MIDI note number currently assigned to Pad 1 will appear in
the display.
1 Display the MIDI Note Number
E1
BEAT
ASSIGN
PAD KIT
2
Select the pad to be assigned a MIDI Note Number
Strike any pad to see the currently assigned MIDI note number in the
display.
Sharp notes are indicated by a dot on the upper left side of the display,
minus values are indicated by a dot on the upper right side of the display.
A1
BEAT
C2
BEAT
(Minus)
# (Sharp)
3 Assign a MIDI Note Number
To select the desired MIDI note number, turn the DIAL to the right
(clockwise) and the MIDI note numbers will increase. Turn the DIAL to
the left (counter-clockwise) and MIDI note numbers will decrease.
You can also select the MIDI note number by striking the pad. Every time the pad
is struck, the value will increase by one.
4 Exit the MIDI/Utility mode
After each pad is assigned a MIDI note number, exit the MIDI/Utility
mode.
For information on transmit notes and voices, refer to the DD-50 Drum Map
(note - voice, list) on page 27.
When the Pad Assign or Kit Assign is set, the MIDI Note Number will be applied
to the preset value. If the Auto Kit Select is set to ON and another Song is
selected, the MIDI Note Number will be applied to the preset value. Auto Kit
Select is automatically turned off when a MIDI Note Number is changed.
Each pad and pedal (9 total) can be assigned a specific MIDI note number anywhere from C-2 to G8.
21
Initialize
The DD-50s Custom Song, Custom Kit, and Panel Setting data are backed up so long as
power is supplied to the DD-50 by means of batteries or an AC adaptor. Initialize is the term
which refers to this data being restored to its original factory settings. To initialize the DD-50,
follow the procedure below.
> Turn the [POWER] switch OFF.
> While holding the [DEMO] button, turn the [POWER] switch
ON. The DD-50 will be initialized to its factory settings. “Cr”
will appear in the display when the initialization process is
complete.
Cr
BEAT
DEMO
POWER
OFF ON
The following data will remain in memory, as long
as batteries are installed or an AC adaptor is con-
nected, even if the power is turned off.
* Custom Song
* Custom Kit
* Reverb Depth
* Auto Kit Selection
* MIDI Transmit Channel for the PAD
* MIDI Note Number for the PAD
Data Backup
POWER
OFF ON
22
In many cases, problems or malfunctions that occur during use can be remedied easily.
Please check the following list before deciding that your DD-50 is damaged.
If the suggested remedy is ineffective, take the DD-50 to an authorized Yamaha dealer for
proper diagnosis and repair. Do not attempt to repair this digital instrument by yourself as
serious damage may occur.
Troubleshooting
Problem Cause/Solution
The song or Demo does not start playback.
The MIDI clock has been set to E (external).
Change the MIDI clock setting to I (internal)
(see page 17).
A buzz or click occurs momentarily when the DD-50
is turned ON or OFF
This is a normal power surge noise that occurs
when the POWER switch is operated
Cr appears in the display when the POWER switch
is turned ON, and backed up data has been erased.
Backed up data is initialized if batteries are not
installed or AC adaptor is disconnected while the
POWER is turned OFF (see page 21).
The selected voice does not sound when the pad is
struck.
The desired voice has not been assigned to the pad.
Use the PAD ASSIGN function to program the
desired voice to the appropriate pad (see page 8).
The batteries are low and should be replaced with a
complete set of six new batteries. Or, an optional AC
adaptor (PA-3 or PA-3B) should be used to power
the DD-50 (see page 3).
The custom pad voice assignments have disap-
peared or defaulted.
Striking two pads simultaneously results in one of
the pads not sounding.
Striking a pad results in other pads also sounding,
though they were not struck.
Refer to Adjusting the Pads Sensitivity to resolve
the problem (see page 30).
The batteries are low and should be replaced with a
complete set of six new batteries immediately. Or,
the optional AC adaptor PA-3 or PA-3B should be
used to power the DD-50 (see page 3).
The LED display is completely dark. When the pads
are struck, the display is dark and returns to 00.
No sound comes from the speakers.
The volume is set too low. Adjust the volume (see
page 6).
A plug is inserted into the PHONES/AUX. OUT
jack and should be taken out (see page 3).
The LOCAL ON/OFF is set to OFF. Set the LOCAL
ON/OFF to ON (see page 18).
You are in the MIDI/Utility mode. Exit the MIDI/
Utility mode (see page 17).
23
Drum Voice List / Drum Voice-Verzeichnis / Liste des voix de batterie /
Lista de voces de batería
Data / Verzeichnisse und Spezifikationen / Données / Datos
Pad assign No. Voice Name
0 Bass Drum Lo
1 Bass Drum Mid
2 Bass Drum Hi
3 Bass Drum Rock
4 Bass Drum Dance
5 Bass Drum Jazz
6 Snare Drum Light
7 Snare Drum Lo
8 Snare Drum Hi
9 Snare Drum Rock Mid
10 Snare Drum Rock Hi
11 Snare Drum Dance
12 Snare Drum Jazz
13 Side Stick
14 Open Rim Shot
15 Sticks
16 High Tom-H
17 High Tom-L
18 Mid Tom-H
19 Mid Tom-L
20 Low Tom-H
21 Low Tom-L
22 Rock H.Tom-H
23 Rock H.Tom-L
24 Rock M.Tom-H
25 Rock M.Tom-L
26 Rock L. Tom-H
27 Rock L. Tom-L
28 Jazz H. Tom-H
29 Jazz H. Tom-L
30 Jazz M. Tom-H
31 Jazz M. Tom-L
32 Jazz L. Tom-H
33 Jazz L. Tom-L
34 *Hi-Hat Closed/Open
35 *Rock HH Closed/Open
36 *Dance HH Closed /Open
37 Crash Cymbal-L
38 Crash Cymbal-H
39 Ride Cymbal
40 Ride Cymbal Cup
41 Chinese Cymbal
42 Splash Cymbal
43 Hand Clap
44 Finger Snap
45 Tambourine
46 Rock Tambourine
47 Cowbell
48 Rock Cowbell
49 Dance Cowbell
50 Latin Cowbell
51 Conga H Mute
52 Conga H Open
53 Conga L
54 Conga Muffled
55 Bongo H
56 Bongo L
57 Timbale H
58 Timbale L
59 Cascala
60 Agogo H
61 Agogo L
62 Cabasa-1
63 Cabasa-2
64 Shaker
65 Rock Shaker
66 Claves
67 Triangle Mute
68 Triangle Open
69 Guiro Short
70 Guiro Long
71 Cuica Mute
72 Cuica Open
73 Surdo Mute
74 Surdo Open
*
By assigning Closed and Open Hi-Hat voices to both the Pad and Pedal, those voices can be controlled with the foot pedal as follows:
Strike the pad while pressing the Foot Pedal, the “Closed” Hi-Hat voice will sound.
Strike the pad without pressing the Foot Pedal, the “Open” Hi-Hat voice will sound.
Press the Foot Pedal without striking the pad, the Hi-Hat “Pedal” voice will sound.
* Durch Zuordnen derselben Hi-Hat-Voice (HH Closed/Open) zu sowohl einem Pad und einem Pedal ist folgende Steuerung mit
dem Pedal möglich:
Beim Anschlagen des Pads mit Pedalbetätigung wird der Klang eines geschlossenen “Closed” Hi-Hat erzeugt.
Beim Anschlagen des Pads ohne Pedalbetätigung wird der Klang eines offenen “Open” Hi-Hat erzeugt.
Betätigen Sie das Pedal, ohne das Pad anzuschlagen. Die Hi-Hat “Pedal” Voice erklingt dabei.
* En affectant les voix de cymbale charleston fermée et ouverte (Closed and Open Hit-Hat) au pad et à la pédale, ces voix
peuvent être contrôlées par la pédale, comme suit.
Frappez le pad tout en appuyant sur la pédale et le son de la cymbale charleston fermée (“Closed”) sortira.
Frappez le pad sans appuyer tout en appuyant sur la pédale et le son de cymbale charleston ouverteÅ (“Open”) sortira.
Appuyez sur la pédale sans frapper le pad, pour entendre la voix “Pédale” charleston.
* Asignando voces de platillos abiertos y cerrados a los pulsadores y los pedales, podrá controlar tales voces con los pedales de
la forma siguiente:
Si golpea el pulsador manteniendo pisado el pedal, sonará la voz de platillos cerrados (“Closed”).
Si golpea el pulsador sin pisar1 el pedal, sonará la voz de platillos abiertos (“Open”).
Pise el pedal sin golpear el pulsador: sonará la voz de “Pedal” de los platillos.
24
Data / Verzeichnisse und Spezifikationen / Données / Datos
Drum Kit List / Drum Kit-Verzeichnis / Liste des kits de batterie / Lista
Small Pad 2
Small Pad 1
Pad 2
Pad 3
Small Pad 3
Pad 4
Pad 1
Pedal 2
Pedal 1
No. Kit Name Pad 1 Pad 2 Pad 3 Pad 4
0 Standard 1 8 Snare Drum Hi 16 High Tom-H 18 Mid Tom-H 20 Low Tom-H
1 Standard 2 7 Snare Drum Lo 17 High Tom-L 19 Mid Tom-L 21 Low Tom-L
2 Standard 3 6 Snare Drum Light 16 High Tom-H 18 Mid Tom-H 20 Low Tom-H
3 Standard 4 8 Snare Drum Hi 16 High Tom-H 18 Mid Tom-H 20 Low Tom-H
4 Standard 5 14 Open Rim Shot 17 High Tom-L 19 Mid Tom-L 21 Low Tom-L
5 Standard 6 13 Side Stick 16 High Tom-H 18 Mid Tom-H 20 Low Tom-H
6 Hard Rock 1 10
Snare Drum
22 Rock H.Tom-H 24 Rock M.Tom-H 26 Rock L.Tom-H
Rock Hi
7 Hard Rock 2 9
Snare Drum
23 Rock H.Tom-L 25 Rock M.Tom-L 27 Rock L.Tom-L
Rock Mid
8 Dance 1 11 Snare Drum Dance 16 High Tom-H 18 Mid Tom-H 20 Low Tom-H
9 Dance 2 6 Snare Drum Light 17 High Tom-L 19 Mid Tom-L 21 Low Tom-L
10 Samba Perc. 73 Surdo Mute 60 Agogo H 61 Agogo L 74 Surdo Open
11 Timbales 58 Timbale L 42 Splash Cymbal 59 Cascala 57 Timbale H
12 Conga 54 Conga Muffled 51 Conga H Mute 52 Conga H Open 53 Conga L
13 Jazz 1 12 Snare Drum Jazz 28 Jazz H.Tom-H 30 Jazz M.Tom-H 32 Jazz L.Tom-H
14 Jazz 2 7 Snare Drum Lo 29 Jazz H.Tom-L 31 Jazz M.Tom-L 33 Jazz L.Tom-L
15 Jazz 3 12 Snare Drum Jazz 28 Jazz H.Tom-H 39 Ride Cymbal 32 Jazz L.Tom-H
16 Twin Bass Drum 8 Snare Drum Hi 23 Rock H.Tom-L 25 Rock M.Tom-L 27 Rock L.Tom-L
17 Rock Perc. 58 Timbale L 46
Rock
65 Rock Shaker 57 Timbale H
Tambourine
18 Ballad Perc. 67 Triangle Mute 66 Claves 45 Tambourine 68 Triangle Open
19 Cymbal 14 Open Rim Shot 38 Crash Cymbal-H 39 Ride Cymbal 37 Crash Cymbal-L
25
de juegos de batería
Data / Verzeichnisse und Spezifikationen / Données / Datos
Small Pad 1 Small Pad 2 Small Pad 3 Pedal 1 Pedal 2
38 Crash Cymbal-H 39 Ride Cymbal 34
HH Open/Closed
1 Bass Drum Mid 34 HH Pedal
(Pedal 2 Off/On)
34
HH Open/Closed
37 Crash Cymbal-L 47 Cowbell 2 Bass Drum Hi 34 HH Pedal
(Pedal 2 Off/On)
38 Crash Cymbal-H 39 Ride Cymbal 35
Rock HH Open/Closed
0 Bass Drum Lo 35 Rock HH Pedal
(Pedal 2 Off/On)
34
HH Open/Closed
38 Crash Cymal-H 13 Side Stick 1 Bass Drum Mid 34 HH Pedal
(Pedal 2 Off/On)
38 Crash Cymbal-H 40 Ride Cymbal Cup 34
HH Open/Closed
1 Bass Drum Mid 34 HH Pedal
(Pedal 2 Off/On)
42 Splash Cymbal 39 Ride Cymbal 34
HH Open/Closed
0 Bass Drum Lo 34 HH Pedal
(Pedal 2 Off/On)
35
Rock HH Open/Closed
38 Crash Cymbal-H 48 Rock Cowbell 3 Bass Drum Rock 35 Rock HH Pedal
(Pedal 2 Off/On)
38 Crash Cymbal-H 40 Ride Cymbal Cup 35
Rock HH Open/Closed
3 Bass Drum Rock 35 Rock HH Pedal
(Pedal 2 Off/On)
36
Dance HH Open/Closed
42 Splash Cymbal 49 Dance Cowbell 4 Bass Drum Dance 36 Dance HH Pedal
(Pedal 2 Off/On)
41 Chinese Cymbal 39 Ride Cymbal 36
Dance HH Open/Closed
0 Bass Drum Lo 36 Dance HH Pedal
(Pedal 2 Off/On)
71 Cuica Mute 72 Cuica Open 63 Cabasa-2 48 Rock Cowbell 45 Tambourine
37 Crash Cymal-L 38 Crash Cymbal-H 50 Latin Cowbell 50 Latin Cowbell 66 Claves
55 Bongo H 56 Bongo L 57 Timbale H 50 Latin Cowbell 47 Cowbell
38 Crash Cymbal-H 39 Ride Cymbal 34
HH Open/Closed
5 Bass Drum Jazz 34 HH Pedal
(Pedal 2 Off/On)
42 Splash Cymbal 39 Ride Cymbal 34
HH Open/Closed
0 Bass Drum Lo 34 HH Pedal
(Pedal 2 Off/On)
34
HH Open/Closed
38 CrashCymbal-H 13 Side Stick 5 Bass Drum Jazz 34 HH Pedal
(Pedal 2 Off/On)
38 Crash Cymbal-H 37 CrashCymal-L 34
HH Open/Closed
1 Bass Drum Mid 1 Bass Drum Mid
(Pedal 2 Off/On)
38 Crash Cymbal-H 41 Chinese Cymbal 42 Splash Cymbal 48 Rock Cowbell 43 Hand Clap
64 Shaker 62 Cabasa-1 42 Splash Cymbal 47 Cowbell 44 Finger Snap
34
HH Open/Closed
40 Ride Cymbal Cup 42 Splash Cymbal 2 Bass Drum Hi 34 HH Pedal
(Pedal 2 Off/On)
26
Data / Verzeichnisse und Spezifikationen / Données / Datos
No Song Name
8 Beat
00 8 Beat 1
01 8 Beat 2
02 8 Beat 3
03 8 Beat 4
04 8 Beat 5
05 8 Beat 6
06 8 Beat 7
07 8 Beat 8
08 8 Beat 9
09 8 Beat 10
10 8 Beat 11
11 8 Beat 12
16 Beat
12 16 Beat 1
13 16 Beat 2
14 16 Beat 3
15 16 Beat 4
16 16 Beat 5
17 16 Beat 6
18 16 Beat 7
19 16 Beat 8
20 16 Beat 9
21 16 Beat 10
22 16 Beat 11
23 16 Beat 12
24 16 Beat 13
25 16 Beat 14
Dance
26 Dance 1
27 Dance 2
28 Dance 3
29 Dance 4
Shuffle
30 Shuffle 1
31 Shuffle 2
32 Shuffle 3
33 Shuffle 4
34 Shuffle 5
35 Shuffle 6
36 Shuffle 7
37 Shuffle 8
38 Shuffle 9
Slow Rock
39 Slow Rock 1
40 Slow Rock 2
41 Slow Rock 3
42 Slow Rock 4
43 Slow Rock 5
Bounce
44 Bounce 1
45 Bounce 2
46 Bounce 3
Latin
47 Reggae 1
48 Reggae 2
49 Bossa Nova
50 Samba
51 Salsa
52 Latin Rock
53 Cha Cha
54 Mambo
55 Rhumba
56 Afro Cuban
Swing
57 Swing 1
58 Swing 2
59 Swing 3
60 Swing 4
Others
61 Swing Waltz
62 Waltz
63 3/4 Ballad
64 Swing Blues
65 Blues
66 6/8
67 5/4
68 March 1
69 March 2
8 Beat
70 8 Beat Simple
71 8 Beat Rock 1
72 8 Beat Rock 2
73 Pop Ballad 1
74 Pop Ballad 2
75 Hard Rock 1
76 Hard Rock 2
77 Hard Rock 3
78 Dance Pop 1
79 Dance Pop 2
80 R&B
16 Beat
81 16 Beat Simple
82 Fusion 1
83 Fusion 2
Funk
84 Funk 1
85 Funk 2
Suffle
86 Shuffle 1
87 Shuffle 2
88 Shuffle 3
89 Slow Rock Simple
90 16 Beat Shuffe
91 16 Beat Triplet
Others
92 Pop Reggae
93 Bossa Nova
94 Samba
95 Latin
96 Salsa
97 5/4 Organ
98 Fast Swing
99 Big Band
Song List / Song-Verzeichnis / Liste des morceaux / Lista de canciones
* Song No. 0-69 : Loop Type (Short)
Song No. 70-99 : Sequence Type (Long)
* Songs 0 bis 69 : Loop (kurz)
Songs 70 bis 99 : Sequence (lang)
* N.° de canción 9-69 : Tipo bucle (corto)
N.° de canción 70-99 : Tipo de secuencia
(largo)
* Morceaux n° 0 à 69 : en boucle (court)
Morceaux n° 70 à 99 : en séquence (long)
27
Bank MSB# 127 127 127 127
Program # 0 16 25 32
Note# Note Standard Rock Kit Hard Rock Kit Dance Kit Jazz Kit
13 C# -1 Surdo Mute <—— <—— <——
14 D -1 Surdo Open <—— <—— <——
15 D# -1 <—— <—— <——
16 E -1 <—— <—— <——
17 F -1 <—— <—— <——
18 F# -1 <—— <—— <——
19 G -1 Finger Snap <—— <—— <——
20 G# -1 <—— <—— <——
21 A -1 <—— <—— <——
22 A# -1 <—— <—— <——
23 B -1 <—— <—— <——
24 C 0 <—— <—— <——
25 C# 0 <—— <—— <——
26 D 0 <—— <—— <——
27 D# 0 <—— <—— <——
28 E 0 <—— <—— <——
29 F 0 <—— <—— <——
30 F# 0 <—— <—— <——
31 G 0 Snare Drum Light <—— <—— <——
32 G# 0 Sticks <—— <—— <——
33 A 0 Bass Drum Lo <—— <—— <——
34 A# 0 Open Rim Shot <—— <—— <——
35 B 0 Bass Drum Mid <—— <—— <——
36 C 1 Bass Drum Hi Bass Drum Rock Bass Drum Dance Bass Drum Jazz
37 C# 1 Side Stick <—— <—— <——
38 D 1 Snare Drum Lo Snare Drum Rock Mid Snare Drum Dance Snare Drum Jazz
39 D# 1 Hand Clap <—— <—— <——
40 E 1 Snare Drum Hi Snare Drum Rock Hi Snare Drum Hi Snare Drum Hi
41 F 1 Low Tom-L Rock L. Tom-L Low Tom. L Jazz L. Tom-L
42 F# 1 Hi-Hat Closed Rock HH Closed Dance HH Closed Hi-Hat Closed
43 G 1 Low Tom-H Rock L. Tom-H Low Tom. H Jazz L. Tom-H
44 G# 1 Hi-Hat Pedal Rock HH Pedal Dance HH Pedal Hi-Hat Pedal
45 A 1 Mid Tom-L Rock M.Tom-L Mid Tom. L Jazz M. Tom-L
46 A# 1 Hi-Hat Open Rock HH Open Dance HH Open Hi-Hat Open
47 B 1 Mid Tom-H Rock M.Tom-H Mid Tom. H Jazz M. Tom-H
48 C 2 High Tom-L Rock H.Tom-L High Tom. L Jazz H. Tom-L
49 C# 2 Crash Cymbal-L <—— <—— <——
50 D 2 High Tom-H Rock H.Tom-H High Tom. H Jazz H. Tom-H
51 D# 2 Ride Cymbal <—— <—— <——
52 E 2 Chinese Cymbal <—— <—— <——
53 F 2 Ride Cymbal Cup <—— <—— <——
54 F# 2 Tambourine Rock Tambourine Tombourine Tombourine
55 G 2 Splash Cymbal <—— <—— <——
56 G# 2 Cowbell Rock Cowbell Dance Cowbell Cowbell
57 A 2 Crash Cymbal-H <—— <—— <——
58 A# 2 <—— <—— <——
59 B 2 Ride Cymbal Cup <—— <—— <——
60 C 3 Bongo H <—— <—— <——
61 C# 3 Bongo L <—— <—— <——
62 D 3 Conga H Mute <—— <—— <——
63 D# 3 Conga H Open <—— <—— <——
64 E 3 Conga L <—— <—— <——
65 F 3 Timbale H <—— <—— <——
66 F# 3 Timbale L <—— <—— <——
67 G 3 Agogo H <—— <—— <——
68 G# 3 Agogo L <—— <—— <——
69 A 3 Cabasa-1 <—— <—— <——
70 A# 3 Shaker Rock Shaker Shaker Shaker
71 B 3 <—— <—— <——
72 C 4 <—— <—— <——
73 C# 4 Guiro Short <—— <—— <——
74 D 4 Guiro Long <—— <—— <——
75 D# 4 Claves <—— <—— <——
76 E 4 <—— <—— <——
77 F 4 <—— <—— <——
78 F# 4 Cuica Mute <—— <—— <——
79 G 4 Cuica Open <—— <—— <——
80 G# 4 Triangle Mute <—— <—— <——
81 A 4 Triangle Open <—— <—— <——
82 A# 4 Cabasa-2 <—— <—— <——
83 B 4 <—— <—— <——
84 C 5 <—— <—— <——
85 C# 5 Conga Muffled <—— <—— <——
86 D 5 <—— <—— <——
87 D# 5 Latin Cowbell <—— <—— <——
88 E 5 Cascala <—— <—— <——
Drum Map / Drum-Notenzurdnung / Topographie de batterie / Mapa de la batería
<—— : The same voice as indicated
in the columm to the left
: No sound
Data / Verzeichnisse und Spezifikationen / Données / Datos
<—— : La misma voz que la indicada
en la columna de la izquierda
: Sin sonido
<—— : La même voix, comme indiqué
dans la colonne à gauche.
: Aucune sonorité
<—— : Wie in der linken
Spalte
: Kein Klang
28
Data / Verzeichnisse und Spezifikationen / Données / Datos
Drum Pads 7 pads (125mm x 4, 88mm x 3), Touch Sensitive
Maximum Polyphony 28
Drum Kits 20 Preset + 1 Custom
Songs 100
Tracks 4 (DRUM 1/DRUM 2/BASS/BACKING)
Custom Song 1 Song (approximately 600 notes)
Drum Voices 75
Auxiliary Functions Track ON/OFF, TAP START, BREAK, A-B REPEAT, DEMO
Panel Controls POWER ON/OFF, SONG VOLUME (large, small), PAD ASSIGN,
KIT ASSIGN, SONG, TEMPO, MASTER VOLUME (large, small), REVERB,
TRACK (DRUM 1/DRUM 2/BASS/BACKING), CLICK, DIAL, START/STOP,
BREAK/TAP START, A-B REPEAT, DEMO
LED Display Song/Drum Kit/Tempo etc.
Connectors DC IN10-12 V
PHONES/AUX OUT
MIDI IN/OUT
PEDAL 1/2
Main Amplifier 3W + 3W (EIAJ)
Speaker 10 cm x 2
Power Source Six “C” size, SUM-2, R-14, or equivalent batteries (sold separately)
DC 10-12V (Yamaha PA-3, PA-3B sold separately)
Dimensions (WxDxH) 552 x 348 x 136 (21” 3/4 x 13” 2/3 x 5” 3/8)
Weight 3.0 kg (6 Ibs. 10 oz)
Supplied Accessories Drum stick x 2, Foot Pedal x 2, Owner’s Manual
Optional Accessories Headphones HPE-150, HPE-3
AC Power Adaptor PA-3, PA3B
Foot Switch FC4, FC5
* Specifications subject to change without notice.
* Änderungen ohne Vorankündigung vorbehalten.
* Sous toute réserve de modification des caractéristiques sans préavis.
* Especificaciones sujetas a cambios sin previo aviso.
Specifications / Technische Daten / Spécifications / Especificaciones
29
MIDI Implementation Chart / Implementierungstabelle /
Table d'implémentation / Gráfico de implementación
[Digital Percussion] Date: 1996. 3. 1
Model: DD-50 MIDI Implementation Chart Version: 1.0
Function Transmitted Recognized Remarks
Basic Default 1~16 CH 1~16 CH
Channel Changed 1~16 CH 1~16 CH
Default Mode 3 Mode 3
Mode Messages XX
Altered ***************** X
Note 0~127 13~96
Number : True voice ***************** 13~96
Velocity Note on O 9nH, v=1~127 O 9nH, v=1~127
Note off X 9nH, v=0 X 9nH, v=0
After key’s XX
Touch Ch’s XX
Pitch Bender OO
Control Change 0, 32 OOBank select MSB, LSB
1 OOModulation depth
6, 38 OOData entry MSB, LSB
7 OOVolume
10 O (*1) O Pan
11 OOExpression
64 OOSustain
91 OOAmbience depth
96 XORPN data increment
97 XORPN data decrement
100, 101 OORPN LSB, MSB
120 XOAll sound off
121 XOReset all controllers
Program OO0~127
Change : True # *****************
System Exclusive XX
System : Song Position XX
: Song Select XX
Common : Tune XX
System : Clock OO
Real Time: Commands OO (*2)
Aux : Local ON/OFF XX
: All Notes Off XX
Messages: Active Sense OO
: Reset XX
Mode 1: OMNI ON, POLY Mode 2: OMNI ON, MONO O: Yes
Mode 3: OMNI OFF, POLY Mode 4: OMNI OFF, MONO X: No
*1 Value of Pan for each drum pad and foot pedal is not transmitted via MIDI.
*1 Pan-Werte der einzelnen Pads und Pedale werden nicht über MIDI übertragen.
*1 La valeur de Pan pour chaque pad de batterie et pour la pédale n’est pas transmise via MIDI.
*1 El valor del efecto panorámico (Pan) para cada pulsador y pedal de batería no se transmite a través de MIDI.
*2 The DD-50 can accept Start/Stop signals, received via MIDI, by setting the MIDI clock to “External”.
*2 Das DD-50 spricht auf über MIDI empfangene Start/Stop-Signale an, wenn es auf externen MIDI-Taktgeber (“E”) gestellt ist.
*2 Le DD-50 peut accepter les signaux Start/Stop reçus via MIDI, en réglant l’horloge MIDI sur “External (E)”.
*2 El DD-50 puede aceptar señales de inicio/parada recibidas a través de MIDI, ajustando el reloj MIDI a “Externo (E)”.
30
Adjusting the Pad’s Sensitivity
The factory default setting for pad sensitivity should provide you with trouble-free use. However, it is possible to
adjust the pad’s sensitivity (0-3, factory default = 2) if you are experiencing one of the problems shown below.
Striking two pads simultaneously results in one of the pads not sounding.
Set the pad sensitivity level to 3. When two pads are simultaneously struck with this setting, both pads will sound
together. However, if you strike the pads with too much force, the voice of a pad that is not struck may also
sound.
Striking a pad results in other pads also sounding, though they were not struck.
Set the pad sensitivity level to 1. With this setting, pads that are not struck will become harder to sound.
However, if you strike two pads simultaneously without enough force, one of the struck pads may not sound.
By setting the pad sensitivity level to 0, pads that are not struck will be even harder to sound.
Setting Procedure
1Press the [START/STOP] and [DEMO] buttons simultaneously, “mm” will
appear in the display.
2Press the large [SONG VOLUME] button to enter the pad sensitivity mode.
The currently selected pad sensitivity setting will appear in the display.
3Turn the DIAL to set the pad sensitivity level (0-3).
4Once again, press the [START/STOP] and [DEMO] buttons simultaneously
to exit the pad sensitivity mode and complete the setting procedure.
SONG
VOLUME
Einstellen der Pad-Empfindlichkeit
Die werkseitige Standardeinstellung für die Pad-Empfindlichkeit sorgt im Normalfall für problemlosen Spieleinsatz.
Sollte jedoch eines der im folgenden angeführten Probleme auftreten, können Sie die Pad-Empfindlichkeit (0 bis 3,
Standardeinstellung = 2) höher oder niedriger einstellen.
Beim gleichzeitigen Anschlagen von zwei Pads erzeugt eines keinen Ton.
Stellen Sie die Pad-Empfindlichkeit auf “3” ein. Wenn Sie bei dieser Einstellung zwei Pads anschlagen, erzeugen
beide Ton. Bei zu starkem Anschlagen kann es jedoch vorkommen, das auch andere Pads “mitschwingen”.
Beim Anschlagen eines Pads erzeugen andere Pads Ton, obwohl sie nicht berührt wurden.
Stellen Sie die Pad-Empfindlichkeit auf “1” ein. Bei dieser Einstellung reagieren die Pads weniger empfindlich.
Wenn jedoch zwei Pads gleichzeitig mit zu wenig Kraft angeschlagen werden, klingt eines davon unter
Umständen nicht.
Wenn die Pad-Empfindlichkeit auf “0” eingestellt wird, schwingen andere Pads nur bei extremer Anschlagstärke mit.
Einstellvorgang
1Die Tasten [START/STOP] und [DEMO] gleichzeitig drücken. “mm” wird
auf dem Display angezeigt.
2Die größere [SONG VOLUME]-Taste drücken, um auf Einstellmodus für
Pad-Empfindlichkeit zu schalten. Die aktuelle Einstellung wird auf dem
Display angezeigt.
3Am Wählrad drehen, um die gewünschte Empfindlichkeit einzustellen.
4Erneut die Tasten [START/STOP] und [DEMO] gleichzeitig drücken, um
den Einstellmodus für Pad-Empfindlichkeit zu verlassen und den
Einstellvorgang zu beenden.
SONG
VOLUME
The pad sensitivity setting is
retained in memory, even if the
power is switched off, as long as
batteries are installed or the power
adaptor is connected to an AC
outlet. If batteries are not installed
and the power adaptor is not
connected to an AC outlet, the
sensitivity setting will return to its
factory default setting (2).
Die Pad-Empfindlichkeitseinstellung
bleibt auch beim Ausschalten des
Instruments gespeichert, solange
Batterien eingelegt sind oder ein
Netzadapter angeschlossen ist.
Wenn keine Batterien eingelegt sind
und der Netzadapter nicht
angeschlossen ist, wird die
Empfindlichkeit auf die werkseitige
Standardeinstellung (2)
zurückgesetzt.
31
Réglage de la sensibilité des pads
Le réglage par défaut en usine de la sensibilité des pads devrait vous permettre une utilisation sans problème.
Cependant, il est possible de régler la sensibilité des pads (de 0 à 3, 2 étant le défaut) au cas où vous seriez confronté
à l’un des problèmes mentionnés ci-dessous.
En frappant sur deux pads en même temps, vous n’entendez qu’un des pads.
Réglez le niveau de sensibilité de pad sur 3. Lorsque vous frappez sur deux pads en même temps avec ce réglage,
les deux pads résonnent ensemble. Cependant, si vous frappez sur les pads avec une force trop grande, vous
pouvez aussi entendre la voix d’un pad que vous n’avez pas touché.
Le fait de frapper un pad fait aussi résonner d’autres pads, même si vous ne les avez pas touchés.
Réglez le niveau de sensibilité de pad sur 1. Avec ce réglage, les pads qui ne sont pas frappés ont plus de mal à
résonner. Cependant, si vous frappez sur les pads avec une force insuffisante, l’un des pads frappés peut ne pas
résonner.
En réglant le niveau de sensibilité de pad sur 0, les pads que vous n’aurez pas touché résonneront encore moins.
Procédure de réglage
1Appuyez en même temps sur les boutons [START/STOP] et [DEMO], pour
faire apparaître “mm” sur l’écran.
2Appuyez sur le gros bouton [SONG VOLUME] pour entrer le mode de
sensibilité de pad. Le réglage de sensibilité du pad actuellement sélectionné
apparaît sur l’écran.
3Tournez la molette DIAL pour fixer le niveau de sensibilité du pad (0 à 3).
4Une fois de plus, appuyez en même temps sur les boutons [START/STOP]
et [DEMO] pour sortir du mode de sensibilité de pad et terminer la
procédure de réglage.
Ajuste de la sensibilidad de los pulsadores
El ajuste de fábrica para la sensibilidad de los pulsadores debe proporcionar un funcionamiento sin problemas. Sin
embargo, es posible ajustar la sensibilidad de los pulsadores (0-3, ajuste de fábrica = 2) si le ocurre alguno de los
problemas que se mencionan a continuación.
Cuando se accionan dos pulsadores simultáneamente, uno de los pulsadores no suena.
Ajuste el nivel de sensibilidad de los pulsadores a 3. Cuando se accionan dos pulsadores simultáneamente con
este ajuste, ambos pulsadores sonarán al mismo tiempo. Sin embargo, si acciona los pulsadores con demasiada
fuerza, la voz de un pulsador que no se ha accionado también puede sonar.
Al accionar un pulsador, también suenan otros pulsadores, aunque no hayan sido accionados.
Ajuste el nivel de sensibilidad a 1. Con este ajuste, será más difícil que suenen los pulsadores que no han sido
accionados. Sin embargo, si acciona dos pulsadores simultáneamente sin suficiente fuerza, es posible que no
suene uno de los pulsadores.
Ajustando el nivel de sensibilidad de los pulsadores a 0, todavía será más difícil que suenen los pulsadores que
no se accionan.
Procedimiento de ajuste
1Presione simultáneamente los botones [START/STOP] y [DEMO], y “mm
aparecerá en el visualizador.
2Presione el botón grande [SONG VOLUME] para entrar en el modo de
sensibilidad de los pulsadores. El ajuste de la sensibilidad de los pulsadores
actualmente seleccionado aparecerá en el visualizador.
3Gire el DIAL para ajustar el nivel de sensibilidad de los pulsadores (0-3).
4Presione otra vez simultáneamente los botones [START/STOP] y [DEMO]
para salir del modo de sensibilidad de los pulsadores y completar este
procedimiento de ajuste.
SONG
VOLUME
SONG
VOLUME
Le réglage de sensibilité de pad
reste mémorisé, même quand
lalimentation est coupée, aussi
longtemps que les piles sont en
place ou que ladaptateur secteur
est branché dans une prise murale.
Quand il ny a plus de piles dans
lappareil et que ladaptateur
secteur est déconnecté à la prise
murale, le réglage de sensibilité
revient au réglage par défaut en
usine (2).
El ajuste de la sensibilidad de los
pulsadores se retienen en la
memoria, incluso cuando se
desconecta la alimentación,
siempre y cuando haya pilas
instaladas o el adaptador de CA
esté enchufado a la toma de
corriente. Si las pilas no están
instaladas y el adaptador de
alimentación no está enchufado a
una toma de corriente, el ajuste
retornará al ajuste de fábrica (2).
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Nie-
derlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más cercana
o el distribuidor autorizado que se lista debajo.
For details of products, please contact your nearest Yamaha or the
authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha
ou au distributeur le plus proche de vous figurant dans la liste suivante.
ITALY
Yamaha Musica Italia S.P.A.,
Home Keyboard Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN
Yamaha-Hazen Electronica Musical, S.A.
Jorge Juan 30, 28001, Madrid, Spain
Tel: 91-577-7270
PORTUGAL
Valentim de Carvalho CI SA
Estrada de Porto Salvo, Paço de Arcos 2780 Oeiras,
Portugal
Tel: 01-443-3398/4030/1823
GREECE
Philippe Nakas S.A.
Navarinou Street 13, P.Code 10680, Athens, Greece
Tel: 01-364-7111
SWEDEN
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1
Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
DENMARK
YS Copenhagen Liaison Office
Generatorvej 8B
DK-2730 Herlev, Denmark
Tel: 44 92 49 00
FINLAND
Warner Music Finland OY/Fazer Music
Aleksanterinkatu 11, P.O. Box 260
SF-00101 Helsinki, Finland
Tel: 0435 011
NORWAY
Narud Yamaha AS
Grini Næringspark 17
N-1345 Østerås, Norway
Tel: 67 14 47 90
ICELAND
Skifan HF
Skeifan 17 P.O. Box 8120
IS-128 Reykjavik, Iceland
Tel: 525 5000
OTHER EUROPEAN COUNTRIES
Yamaha Europa GmbH.
Siemensstraße 22-34, 25462 Rellingen, F.R. of
Germany
Tel: 04101-3030
ASIA
HONG KONG
Tom Lee Music Co., Ltd.
11/F., Silvercord Tower 1, 30 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel: 730-1098
INDONESIA
PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
KOREA
Cosmos Corporation
#131-31, Neung-Dong, Sungdong-Ku, Seoul
Korea
Tel: 02-466-0021~5
MALAYSIA
Yamaha Music Malaysia, Sdn., Bhd.
16-28, Jalan SS 2/72, Petaling Jaya, Selangor,
Malaysia
Tel: 3-717-8977
PHILIPPINES
Yupangco Music Corporation
339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,
Makati, Metro Manila, Philippines
Tel: 819-7551
SINGAPORE
Yamaha Music Asia Pte., Ltd.
Blk 17A Toa Payoh #01-190 Lorong 7
Singapore 1231
Tel: 354-0133
TAIWAN
Kung Hsue She Trading Co., Ltd.
No. 322, Section 1, FuHsing S. Road,
Taipei 106, Taiwan. R.O.C.
Tel: 02-709-1266
THAILAND
Siam Music Yamaha Co., Ltd.
865 Phornprapha Building, Rama I Road,
Patumwan, Bangkok 10330, Thailand
Tel: 2-215-3443
THE PEOPLE’S REPUBLIC OF CHINA
AND OTHER ASIAN COUNTRIES
Yamaha Corporation,
International Marketing Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430
Tel: 053-460-2317
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
17-33 Market Street, South Melbourne, Vic. 3205,
Australia
Tel: 3-699-2388
NEW ZEALAND
Music Houses of N.Z. Ltd.
146/148 Captain Springs Road, Te Papapa,
Auckland, New Zealand
Tel: 9-634-0099
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation,
International Marketing Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430
Tel: 053-460-2317
MIDDLE & SOUTH AMERICA
MEXICO
Yamaha De Mexico S.A. De C.V.,
Departamento de ventas
Javier Rojo Gomez No.1149, Col. Gpe Del
Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.
Tel: 686-00-33
BRASIL
Yamaha Musical Do Brasil LTDA.
Ave. Reboucas 2636, São Paulo, Brasil
Tel: 011-853-1377
PANAMA
Yamaha De Panama S.A.
Edificio Interseco, Calle Elvira Mendez no.10,
Piso 3, Oficina #105, Ciudad de Panama, Panama
Tel: 507-69-5311
OTHER LATIN AMERICAN COUNTRIES
AND CARIBBEAN COUNTRIES
Yamaha Music Latin America Corp.
6101 Blue Lagoon Drive, Miami, Florida 33126,
U.S.A.
Tel: 305-261-4111
MIDDLE EAST
TURKEY/CYPRUS
Yamaha Musique France, Division Export
BP 70-77312 Marne-la-Valée Cedex 2, France
Tel: 01-64-61-4000
OTHER COUNTRIES
Yamaha Corporation,
International Marketing Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430
Tel: 053-460-2312
EUROPE
THE UNITED KINGDOM
Yamaha-Kemble Music (U.K.) Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: 01908-366700
IRELAND
Danfay Ltd.
61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin
Tel: 01-2859177
GERMANY/SWITZERLAND
Yamaha Europa GmbH.
Siemensstraße 22-34, 25462 Rellingen, F.R. of
Germany
Tel: 04101-3030
AUSTRIA
Yamaha Music Austria
Schleiergasse 20, A-1100 Wien Austria
Tel: 0222-60203900
THE NETHERLANDS
Yamaha Music Nederland
Kanaalweg 18G, 3526KL, Utrecht, The Netherlands
Tel: 030-2828411
BELGIUM
Yamaha Music Belgium
Keiberg Imperiastraat 8, 1930 Zaventem, Belgium
Tel: 02-7258220
FRANCE
Yamaha Musique France,
Division Claviers
BP 70-77312 Marne-la-Valée Cedex 2, France
Tel: 01-64-61-4000
AFRICA
Yamaha Corporation,
International Marketing Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430
Tel: 053-460-2312
[PK] 7
HEAD OFFICE Yamaha Corporation, Electronic Musical Instrument Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430
Tel: 053-460-3273
M.D.G., EMI Division © 1996 Yamaha Corporation
VU54270 Printed in Malaysia

Documenttranscriptie

ENGLISH Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones 2 ESPAÑOL FRANÇAIS DEUTSCH DIGITAL SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adaptor). DO NOT connect this product to any power supply or adaptor other than one described in the manual, on the name plate, or specifically recommended by Yamaha. This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please observe all safety markings and instructions that accompany the accessory product. Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. SPECIFICATIONS SUBJECT TO CHANGE: This product may also use “household” type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that the charger is intended for the battery being charged. The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units. When installing batteries, do not mix batteries with new, or with batteries of a different type. Batteries MUST be installed correctly. Mismatches or incorrect installation may result in overheating and battery case rupture. This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for long periods of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. IMPORTANT: The louder the sound, the shorter the time period before damage occurs. NOTICE: Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following: Warning: Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by the laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information. Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly. NAME PLATE LOCATION: The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate. You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase. Model Serial No. Purchase Date PLEASE KEEP THIS MANUAL 92-BP FCC INFORMATION (U.S.A.) This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: IMPORTANT: • Relocate either this product or the device that is being affected by the interference. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. The serial number of this product may be found on the bottom of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. DD-50 • Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. • In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 • This applies only to products distributed by Yamaha Corporation of America. Entsorgung leerer Batterien (nur innerhalb Deutschlands) Leisten Sie einen Beitrag zum Umweltschutz. Verbrauchte Batterien oder Akkumulatoren dürfen nicht in den Hausmüll. Sie können bei einer Sammelstelle für Altbatterien bzw. Sondermüll abgegeben werden. Informieren Sie sich bei Ihrer Kommune. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Congratulations! ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Thank you for purchasing the Yamaha DD-50. The DD-50 has been developed to act and play like a drum set but with greater ease. Before you use the instrument, we recommend you to read through this manual. ○ ○ ○ ○ ○ ○ ○ Taking Care of Your DD-50 ○ ○ ○ ○ ○ ○ ○ Your DD-50 will give you years of playing pleasure if you follow the simple rules given below: ■ Location Do not expose the instrument to the following conditions to avoid deformation, discoloration, or more serious damage. ● Direct sunlight (e.g. near a window). ● High temperatures (e.g. near a heat source, outside, or in a car during the daytime). ● Excessive humidity. ● Excessive dust. ● Strong vibration. ■ Power Supply ● Turn the power switch OFF when the instrument is not in use. ● An AC adaptor, if used (the DD-50 runs from either batteries or an optional AC adaptor), should be unplugged from the AC outlet if the instrument is not to be used for an extended period of time. ● Unplug the AC adaptor during electric storms. ● Avoid plugging the AC adaptor into the same AC outlet as appliances with high power consumption, such as electric heaters or ovens. Also avoid using multi-plug adaptors since these can result in reduced sound quality, operation errors, and possibly damage. ■ Turn Power OFF When Making Connections ● To avoid damage to the instrument and other devices to which it is connected, turn the power switches of all related devices OFF prior to connecting or disconnecting cables. ■ Handling and Transport ● Always unplug cables by gripping the plug firmly, not by pulling on the cable. ● Disconnect all cables before moving the instrument. ● Physical shocks caused by dropping, bumping, or placing heavy objects on the instrument can result in scratches and more serious damage. ■ Cleaning ● Clean the cabinet and panel with a dry soft cloth. ● A slightly damp cloth may be used to remove stubborn grime and dirt. ● Never use cleaners such as alcohol or thinner. ● Avoid placing vinyl objects on top of the instrument (vinyl can stick to and discolor the surface). ■ Electrical Interference ● This instrument contains digital circuitry and may cause interference if placed too close to radio or television receivers. If this occurs, move the instrument further away from the affected equipment. ■ Data Backup ● Custom data and some settings (see page 21) will be retained in memory even if the power switch is turned OFF as long as an AC power adaptor is connected or batteries are installed. ■ Service and Modification ● The DD-50 contains no user serviceable parts. Opening it or tampering with it in anyway can lead to irreparable damage and possibly electric shock. Refer all servicing to qualified YAMAHA personnel. ● Never apply excessive force to the controls, connectors or other parts of the instrument. YAMAHA is not responsible for damage caused by improper handling or operation. 1 ○ ○ ○ ○ ○ ○ ○ ○ Table of Contents Setting up the DD-50 3 Power Supply ................................................ 3 When Using headphones (About the PHONES/AUX OUT jack) ............ 3 Control Panel 4 Connecting the foot pedals 1/2 ..................... 5 Supplied Accessories ................................... 5 Playing the Demo Song 6 ● MASTER VOLUME ....................................... 6 ● SONG VOLUME ........................................... 6 Play the Pads/Pedals 7 Pad Names ................................................... 7 Assigning a Drum Kit to the Pads and Pedals ........................................... 8 Assigning a Voice to Individual Pads and Pedals (“CU” Custom Kit) ............. 8 REVERB ON/OFF ........................................ 9 ● Select the REVERB Depth ............................ 9 CLICK ON/OFF ............................................. 9 Playing a SONG 12 TRACK ON/OFF ......................................... 12 TAP START ................................................. 12 BREAK ........................................................ 13 A-B REPEAT ............................................... 14 ● Cancel the Repeat Points ............................ 14 2 15 RECORD .................................................... 15 Playback ..................................................... 15 Using the MIDI/Utility Mode 16 What is MIDI? ............................................. 16 What you can do with MIDI ......................... 16 Enter/Exit the MIDI/Utility Mode .................. 17 Setting the Clock ......................................... 17 Local ON/OFF ............................................. 18 Setting the MIDI Transmit Channel ............. 18 Setting the MIDI Note Number .................... 20 Initialize 21 ● Data Backup .............................................. 21 Troubleshooting 22 Data 23 10 Selecting a SONG ...................................... 10 Auto Kit Select ON/OFF Setting .................. 10 Adjusting the TEMPO ................................. 11 Play along with a SONG Try Recording ○ ○ ○ ○ ○ ○ ○ ○ Drum Voice List ........................................... 23 Drum Kit List ............................................... 24 Song List ..................................................... 26 Drum Map ................................................... 27 Specifications .............................................. 28 MIDI Implementation Chart ......................... 29 Setting up the DD-50 Power Supply Your DD-50 will run either from batteries or an optional power adaptor. Follow the instructions below according to the power source you intend to use. Connect the optional power adaptor (Yamaha PA-3 or PA-3B) to the DC IN 10-12V jack located on the unit’s left side panel, and plug the AC power adaptor into an AC power outlet. PA-3/ PA-3B 1 Open the battery compartment cover on the underside of the DD-50. 2 Insert six “C” size, R14, SUM-2 or equivalent batteries. When inserting the batteries, be careful to follow the polarity markings in the illustration. 3 Close the battery compartment cover securely. AC power socket OPEN DC IN 10 - 12V Installing Batteries • Do not attempt to use an AC adaptor other than the PA-3 or PA-3B. Use of an incompatible adaptor may result in the instrument becoming hot or, irreparable damage to the DD-50. It may also result in fire. If the instrument is damaged due to use of an incompatible adaptor, YAMAHA is not responsible for the damage. When Using Headphones (About the PHONES/AUX OUT Jack) An optional set of stereo headphones (such as the Yamaha HPE-150 or HPE-3) can be connected to the PHONES/AUX OUT jack located on the side panel. When a pair of headphones is connected to the jack, the DD-50’s internal speakers will switch off automatically, perfect for private practice or late night playing. If you want to use an external sound system, the headphone jack can also be used to connect the DD-50 to a stereo system or mixing console. (Use a standard plug n pin plug adaptor to connect the DD-50 to a stereo system.) * Turn the power OFF on all equipment before making any connections. OPEN Using an AC-Adaptor (sold separately) • Power will be automatically drawn from the AC adaptor if an optional AC adaptor is connected while batteries are installed in the instrument. • It is recommended that you replace worn batteries as soon as possible. When battery voltage drops, the DD-50’s display will dim and/or the sound will become distorted. When this occurs, replace the batteries with a complete set of six new batteries of the same type. • NEVER mix old and new batteries, different types of batteries (alkaline, magnesium, etc.), batteries by different makers, or batteries from the same maker but of different types. Misuse may cause the instrument to become hot, result in fire, or battery leakage. • Also, to prevent damage due to battery leakage, remove all of the batteries from the instrument when it is not to be used for an extended period of time. Batteries left in an unused instrument will also loose their power over time. 3 Control Panel & * DC IN 10 - 12V ( PHONES / AUX OUT 3 4 5 6 2 PAD KIT SONG SONG VOLUME POWER OFF 1 Front Panel ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ MASTER VOLUME REVERB DRUM 1 DRUM 2 8 9 TEMPO BEAT 88 BASS BACKING CLICK 0 Page 1 POWER ON/OFF Switch ............................... 6 2 SONG VOLUME buttons ............................... 6 3 PAD ASSIGN button ................................ 8, 19 4 KIT ASSIGN button ................................. 8, 20 5 SONG button ............................................... 10 6 TEMPO button ............................................. 11 7 Display ........................................................... 8 8 MASTER VOLUME buttons ........................... 6 9 REVERB button ............................................. 9 0 Track buttons DRUM 1 button ...................................... 12, 17 DRUM 2 button ...................................... 12, 18 BASS button ................................................ 12 BACKING button .................................... 11, 12 4 ON 7 PRESET TEMPO ASSIGN ! CLICK button ................................................. 9 @ DIAL ............................................................... 8 # START/STOP button .................................... 10 $ BREAK/TAP START button .................... 12, 13 % A-B REPEAT button ..................................... 14 ^ DEMO button ................................................. 6 & Drum Pads (x 7) ............................................ 7 ! Control Panel ) MIDI IN MIDI OUT PEDAL 1 RE START/ STOP @ # A-B REPEAT % q PEDAL 2 C. BREAK/ TAPSTART $ DEMO DD-50 ^ Connecting the Foot Pedals (1/2) The supplied foot pedals can be connected to the DD-50 to similarly play the drum set’s hi-hat pedal or bass drum voices or they can also be assigned to play other voices as well. • Do not press the pedal while connecting it to the DD-50 or while turning on the power. (Connecting in this manner with the power on, the pedal’s function may be reversed.) Side Panel (Left) * DC IN 10-12V (AC Adaptor) Jack .................. 3 ( PHONES/AUX OUT Jack .............................. 3 Side Panel (Right) ) MIDI IN/MIDI OUT Terminals ....................... 16 q PEDAL 1/2 Jacks ........................................... 5 ● Supplied Accessories Foot Pedal x 2 Drum Stick x 2 Owner’s Manual 5 Playing the Demo Song To give you idea of the DD-50’s possibilities, it comes with a demonstration song. To playback the demo song: 1 POWER OFF ON Turn on the power Turn the [POWER] switch ON. 2 DEMO Start the Demo Song Press the [DEMO] button, the demo song will start playback. ● MASTER VOLUME The overall volume level of the DD-50 is controlled by two [MASTER VOLUME] buttons (10 volume levels L0-L9). Press the large [MASTER VOLUME] button to increase the overall volume by one level. Press the small [MASTER VOLUME] button to decrease the overall volume one level. Holding down either of the buttons increases or decreases the volume level rapidly. MASTER VOLUME Small Large L0 Small < L5 > < Volume Level > L9 Large *When the MASTER VOLUME is set to L0, the song’s volume is silenced. ● SONG VOLUME The song’s volume level is controlled by the two [SONG VOLUME] buttons (10 volume levels L0-L9). (Demo Song, Song see page 10) SONG VOLUME Small Large The SONG VOLUME can be used to adjust the balance between the song accompaniment and your own performance on the pads. Press the large [SONG VOLUME] button to increase the song volume by one level. Press the small [SONG VOLUME] button to decrease the song volume by one level. Holding either of the buttons increases or decreases the song volume level rapidly. L0 Small < L5 > < Volume Level > L9 Large * When the SONG VOLUME is set to L0, the song’s volume is silenced. RE DEMO C. START/ STOP A-B REPEAT 6 BREAK/ TAPSTART 3 Stop the Demo Song To stop playback, press either the [DEMO] button again or the [START/STOP] button. Play the Pads/Pedals Strike the pad with the supplied drum sticks to play the drum voices. Drum Kit “00” is automatically chosen whenever the power is turned on (see the “Drum Kit List” page 24). Striking the pads with different force results in relatively loud or soft sounds accordingly. Loudness of the sound may vary according to which part of the pad is struck. Pad Names A hi-hat sound is assigned to the Small Pad 3 (Drum Kit 00). Striking the Small Pad 3while pressing on Pedal 2 produces a closed hi-hat sound. Striking the pad without pressing the pedal produces an open hi-hat sound. Small Pad 1 Small Pad 2 38: Crash Cymbal (High) 39: Ride Cymbal Pad 2 Pad 3 16: High Tom (High) 18: Mid Tom (High) Small Pad 3 34: Hi-Hat Close/Open Pad 1 8: Snare Drum (High) Pad 4 20: Low Tom (High) Ex. shown, Drum Kit 00 : Standard 1 Pedal 2 34: Hi-Hat Pedal The bass drum voice is controlled by pressing Foot Pedal 1. Use Foot Pedal 2 to control the Hi-hat. (This is in the case of Drum Kit 00.) Pedal 1 1: Bass Drum (Mid) 7 Play the Pads/Pedals Assigning a Drum Kit to the Pads and Pedals The DD-50 allows you to choose from 20 different Drum Kits (00-19 : see the “Drum Kit List” page 24) quickly and easily. 20 of the kits have preset voice combinations that will be set to the pads and pedals when the kit is selected. Select some different kits and try playing them. The DD-50 also has one Custom Drum Kit allowing you to assign the desired voices to the seven pads or two pedals (see “Assigning a Voice to Individual Pads and Pedals” below). 1 ASSIGN Press the [KIT ASSIGN] button BEAT PAD KIT 10 Pressing the [KIT ASSIGN] button, the button’s lamp will light and the currently selected Drum Kit number appears on the display. 2 Select a Drum Kit Number Turn the DIAL to select a Drum Kit number. Drum Kit numbers will increase as the DIAL is turned to the right (clockwise), and decrease as the DIAL is turned to the left (counter-clockwise). 00 19 CU • Drum Kit number 00 is normally selected when the power is turned ON. However, if Auto Kit Select is set to OFF, the last Drum Kit selected before turning the power OFF, is automatically selected when the power is turned ON. (See “Auto Kit Select ON/OFF Setting” on page 11) • The “CU” Drum Kit is the Custom Kit. Changes made to any one of the preset drum kits will be saved here. (See “Assigning a Voice to Individual Pads and Pedals” below.) Assigning a Voice to Individual Pads and Pedals (“CU” Custom Kit) The DD-50 contains a total of 75 high quality drum sounds (see the “Drum Voice List” page 23) that can be assigned to each of the 7 drum pads and 2 foot pedals. Try assigning some different voices to the “CU” Custom Drum Kit. • Any change made to one of the preset drum kits will automatically be saved in the “CU” Custom Drum Kit. • Both the Custom and “00” drum kit contents are the same until modified (see the “Drum Kit List” page 24). ASSIGN PAD KIT BEAT 1 25 BEAT 10 8 Press the [PAD ASSIGN] button Press the [PAD ASSIGN] button, Pad 1’s currently assigned voice number is shown in the display. 2 Select a Pad/Pedal Strike any pad one time (or press a pedal), that pad’s/pedal’s currently assigned voice number is shown in the display. Play the Pads/Pedals 3 Select a Voice Number You can select the voice by repeatedly striking the pad, repeatedly pressing the pedal (while listening to the voice) or by turning the DIAL. ● Striking the pad or pressing the pedal to select a voice. First, select a pad or pedal by striking or pressing it once. After the pad/pedal has been selected, every time the pad is struck or a pedal is pressed, voice numbers will increase by a value of one (1). 0 1 . . .73 74 @ ● Using the DIAL to select a voice. Turn the DIAL to the right (clockwise), and voice numbers will increase. Turn the DIAL to the left (counter-clockwise), and voice numbers will decrease. 0 1 . . .73 74 @ 4 PRESET TEMPO SONG Play the Pads and Pedals After assigning a voice to the desired pad/pedal, press the [SONG] button. You can now play the voice you have assigned to the pad/pedal. TEMPO Repeat the previous steps for any or all of the DD-50’s pads and pedals and try playing your own original drum kit. REVERB ON/OFF REVERB Different depths of the DD-50’s reverb effect can be selected to add to the DD-50’s overall sound. To turn on the reverb effect, press the [REVERB] button. To turn off the reverb effect, press the [REVERB] button again. ● Select the REVERB Depth REVERB BEAT r1 When the reverb has been turned on, press and hold the [REVERB] button, turn the DIAL to select one of the three reverb depths that appear in the display. [r1], [r2], [r3]. Selecting [r3] adds the most reverb depth to the effect. • REVERB Depth data is not transmitted or received via MIDI. CLICK ON/OFF CLICK The DD-50’s CLICK feature produces a metronome click to make the tempo easier to follow and improve your timing while playing the pads. To hear the metronome click, press the [CLICK] button. To turn the click off, press the button once again. 9 Playing a SONG The DD-50 features 100 different songs that can be used to provide accompaniment (see the “Song List” page 26). Select one of the songs and have a listen. Selecting a SONG PRESET TEMPO SONG BEAT TEMPO 1 10 Press the [SONG] button Press the [SONG] button, its LED indicator will light, and the currently selected song number will appear in the display. 2 Use the DIAL to select a song number Song numbers will increase in value as the DIAL is turned to the right (clockwise) and decrease as the DIAL is turned to the left (counterclockwise). (See the “Song List” on page 26) 00 01 . . .99 RE 3 C. START/ STOP • Song number “00” is automatically selected whenever the power is turned ON. • With the Auto Kit Select turned on, selecting a song will also automatically select the best suited Drum Kit for that song (see “Auto Kit Select ON/OFF Setting” below). • Song numbers are arranged according to their complexity. Smaller numbers are easier to play than larger numbers. CU BREAK/ TAPSTART Press the [START/STOP] button Press the [START/STOP] button, after a two-measure count-in (or one measure count-in), the song will start playback. A-B REPEAT As the song is playing, the Song’s current measure will be shown in the display. Try playing the pads and pedals along with the song. To stop playback of the song, press the [START/STOP] button once again. • You can also use the TAP START function to start songs (see page 12). The DD-50’s songs consists of two types, loop type and sequence type (see the “Song List” page 26). Sequence type songs will automatically stop when the song reaches its end. Loop type songs will continuously play from the time the [START/ STOP] button is initially pressed, until the button is pressed once again. Sequence Loop Auto Kit Select ON/OFF Setting The Auto Kit Select function automatically selects the best matching drum kit to the selected song. You can deactivate this feature by setting the Auto Kit Select to OFF. 1 Setting the Auto Kit Select to ON or OFF Press the [DEMO] and [START/STOP] buttons simultaneously to enter the MIDI/Utility Mode . 10 Playing a SONG BACKING BEAT on 2 Select ON or OFF Press the [BACKING] button and the current ON/OFF setting will appear in the display. Turn the DIAL to the right (clockwise) to activate the Auto Kit Select (on). Turn to the left (counter-clockwise) to deactivate the Auto Kit Select (oF). BEAT oF 3 Exit the Auto Kit Select Press the [DEMO] and [START/STOP] buttons simultaneously once again to exit the MIDI/Utility Mode . • The Auto Kit Select is automatically set to “OFF” when the MIDI Transmit Note is changed to another channel. Adjusting the TEMPO The song tempo can be set anywhere from 40 to 280 beats per minute. As tempo numbers increase, the tempo will become faster. PRESET TEMPO SONG BEAT TEMPO 1 50 Press the [TEMPO] button, the current tempo value (40-280) appears in the display. 2 40 41 7 , 9 , PRESET TEMPO SONG TEMPO Press the [TEMPO] button Tempo Display Comment q=90 q=110 q=250 90 1 , 0 5 , 0 , — 100th digit (1) is shown as a single dot 100th digit (2) is shown as two dots Set the Tempo Use the DIAL to select the TEMPO. Turn the DIAL to the right (clockwise) to increase Tempo values, turn to the left (counter-clockwise) to decrease Tempo values. (Tempo values will cycle to 40 or 280 then stop.) 8 , 0 , 3 Exit the Tempo setting mode Press the [SONG] button to exit from the Tempo setting mode. • When both the SONG and TEMPO buttons are pressed simultaneously, the preset tempo of the currently selected song will automatically applied. BEAT 90 ● About the Beat Indicator During song playback, the two beat lamps in the display will flash in a specific pattern to assist you in keeping the beat. q= 90 beats per minute. 1st beat 2nd beat 3rd beat 4th beat 9 , 0 , 9,0 9,0 9,0 11 Play along with a SONG Use the pads and pedals to play along with a song accompaniment. • The DD-50 can play a total of 28 notes simultaneously. That includes notes produced by song accompaniment, pads, foot pedals, and note data received through the MIDI IN jack. TRACK ON/OFF The DD-50’s song accompaniment consists of 4 tracks; Drum 1/2, Bass, and Backing tracks. DRUM 1 DRUM 2 BASS BACKING DRUM 1 DRUM 2 BASS Main Drum track Main Percussion track Bass track Main Backing Track Pressing a Track button ([DRUM 1], [DRUM 2], [BASS], [BACKING]) will mute (turn off the sound) the corresponding track and its indicator lamp will turn off. BACKING Muting DRUM 1 and DRUM 2 tracks allows you to practice your playing technique in Karaoke style (Minus One). TAP START The TAP START function allows you to set the song’s overall tempo as well as start the accompaniment. The accompaniment will playback at the tempo with which the pads are struck or the pedals are pressed. 1 RE Press the [BREAK/TAP START] button C. Press the [BREAK/TAP START] button when the song stops, its indicator will flash and the DD-50 is in Tap Start standby mode. BREAK/ TAPSTART START/ STOP A-B REPEAT To cancel the Tap Start mode, simply press the [BREAK/TAP START] button once again (the indicator will turn off). 2 Tap Start In the case of a song in 4/4, strike any pad or press any pedal four times, the accompaniment will start at the desired tempo. • The number of times needed to strike the pad will change according to the following time signatures; 5/4, 5 times; 4/4, 4 times; 3/4, 3 times; 6/8, 2 times. RE C. START/ STOP A-B REPEAT 12 BREAK/ TAPSTART 3 Stop the Song Playback To stop playback, press the [START/STOP] button. Play along with a SONG BREAK With the BREAK function, you can liven up songs by adding your own solos or fills, whenever you want. Striking a pad while in the BREAK mode, the song’s accompaniment will be muted until the end of the measure you have finished your fill or solo in. 1 RE During song playback, press the BREAK/TAP START button C. BREAK/ TAPSTART START/ STOP During song playback, press the [BREAK/TAP START] button, its indicator will flash and the DD-50 is in BREAK standby mode. A-B REPEAT To cancel the Break mode, simply press the [BREAK/TAP START] button once again (its indicator will turn off). 2 Break Strike any pad and the accompaniment will mute until the end of the measure you played in. You can play a drum fill or drum solo during this break. RE C. START/ STOP A-B REPEAT BREAK/ TAPSTART 3 Exit the BREAK mode The DD-50 returns to the BREAK standby mode when the BREAK measure is completed. To exit the BREAK mode, press the [BREAK/TAP START] button. The BREAK mode is also exited when the song is stopped. 13 Play along with a SONG A-B REPEAT If you want to practice a particular section of a song, you can specify that section’s “A” (start repeat) and “B” (end repeat) points. The accompaniment will continuously repeat between points “A” and “B” allowing you to practice between those points for as long as you like. 1 RE C. BREAK/ TAPSTART START/ STOP To set the “A” (start repeat) point BEAT When the song playback has reached the start of the section you want to practice, press the [A-B REPEAT] button and the “A” repeat point is set. An “A” will appear in the display. A A-B REPEAT 2 To set the “B” (end repeat) point RE C. BREAK/ TAPSTART START/ STOP When the song playback has reached the end point of the section you want to practice, press the [A-B REPEAT] button once again and the A to B repeat points are set, “b” appears in the display. “Ab” will appear in the display and after a one measure count-in the repeat playback will start. The current measure number will appear in the display during the repeat playback. BEAT Ab A-B REPEAT • The A-B REPEAT start and end points can only be set in measure steps. • Songs consist of two types; loop type and sequence type (see the “Song List” on page 26). When setting the A-B points for sequence songs, set both points before the end of the song. The set “A” point will be canceled if the “B” point is not set before the end of the song. 3 RE C. START/ STOP BREAK/ TAPSTART BEAT Ab A-B REPEAT Stop the A-B REPEAT mode Press the [START/STOP] button and the song accompaniment will stop. “Ab” will appear in the display indicating the A-B REPEAT mode is still engaged. Press the [START/STOP] button once again and the accompaniment will again repeat between the set points. • In the case of a loop type song, it is possible, for example, to set the “A” point at measure 10 and set the “B” point at measure 3 (after the song has looped back to the beginning). B A 3 10 • Selecting another song will cancel any previously set A-B REPEAT points. RE C. START/ STOP A-B REPEAT 14 BREAK/ TAPSTART ● Cancel the Repeat Points To cancel the A-B REPEAT, press the [A-B REPEAT] button during playback or while playback is stopped, the A-B REPEAT mode will be canceled (the A-B REPEAT points will also be canceled) and normal playback of the accompaniment will continue. Try Recording The DD-50’s Custom Song feature (song number “CU”) allows you to record and playback one original song (600 notes approximately). ● Data that can be recorded in the Custom Song Mode. • Drum pad and pedal data. • Song data (the number cannot be changed while in the RECORD Mode). • Track ON/OFF settings. • Tempo setting (The tempo cannot be changed while in the RECORD mode). • Song Volume setting. • Reverb ON/OFF setting. • Break ON/OFF setting. * MIDI data cannot be recorded to the memory. RECORD 1 Prepare to Record Select the desired song, drum kit, tempo, track on/off setting, and reverb settings. 2 Start Recording RE C. START/ STOP BREAK/ TAPSTART Press both the [START/STOP] and [BREAK/TAP START] buttons simultaneously, after a count-in (the indicator will flash) recording will start. BEAT oo A-B REPEAT • Data will not be recorded during the 2 measure count-in. • Press the BREAK/TAP START button during the 2 measure count-in to enter Tap Start Record Standby mode (see page 12). • Press the CLICK button to cancel the metronome during recording. 3 RE C. START/ STOP BREAK/ TAPSTART A-B REPEAT Stop Recording To stop recording, press the [START/STOP] button. • Any previously recorded data will be replaced with new data. • If the memory becomes full while recording is in progress, “FL” will appear in the display and recording will automatically stop. Playback The recorded Custom Song (song number “CU”) can be played back in the same manner as any song (song numbers “00”-”99”). BEAT CU Song number “CU” follows Song number “99” (or prior to “00”). • The A-B REPEAT mode (see 14 page) cannot be used in the Custom Song Mode. 15 Using the MIDI/Utility Mode The MIDI IN and MIDI OUT terminals, located on the DD-50’s right side panel, offer broadened musical possibilities through use of MIDI. But, what is MIDI? What can you do with MIDI? How can you use MIDI with the DD-50? Here are a few examples. What is MIDI? MIDI stands for Musical Instrument Digital Interface. MIDI is a world wide standard that makes it possible for various electronic musical instruments and other devices, such as computers, to “communicate” with each other. For example, by connecting a MIDI tone generator to the DD-50’s MIDI OUT terminal, you can play the tone generator’s voices from the DD-50’s pads and pedals. The DD-50 is equipped with two types of MIDI terminals, both are located on the right side panel. ● MIDI IN Data transmitted from other MIDI instruments via MIDI, is received at this terminal. MIDI OUT MIDI IN ● MIDI OUT Data produced by the DD-50, is transmitted to other MIDI instruments via MIDI from this terminal. • Use a MIDI cable (option), obtainable at your local music dealer, when making MIDI connections. • Never use MIDI cables longer than 15 meters in length. (Cables longer than 15 meters can pick up “noise” which can cause data errors.) What you can do with MIDI DD-50 MIDI Keyboard’s MIDI OUT MIDI IN DD-50 MIDI OUT Sequencer MIDI IN Yamaha MIDI Data Filer MDF2 etc. DD-50 MIDI Keyboard MIDI OUT MIDI IN DD-50 Sequencer MIDI OUT MIDI IN 16 ● Connect the DD-50’s MIDI OUT jack to a MIDI keyboard’s (or tone generator’s) MIDI IN jack. This setup allows you to use the DD-50’s pads to control another MIDI instrument. Playing the DD-50’s pads will result in the other MIDI instrument’s voice sounding simultaneously, creating a thicker overall sound. ● Connect the DD-50’s MIDI OUT jack to a MIDI sequencer’s MIDI IN terminal. Data produced by the DD-50 (Key ON and Velocity data) can be recorded to a MIDI sequencer. Data can also be recorded to computers or other sequencers as well. ● Connect the DD-50’s MIDI IN terminal to a MIDI keyboard’s MIDI OUT terminal. In this setup the DD-50 can be used as a tone generator and its voices can be played from a MIDI keyboard. Using a keyboard as a controller, it is possible to play DD-50 voices that are not assigned to the pads/pedals. ● Connect the DD-50’s MIDI IN terminal to a MIDI sequencer’s MIDI OUT terminal. The sequencer’s data can be used to drive the DD-50’s sounds. Using the MIDI/Utility Mode Enter/Exit the MIDI/Utility Mode RE C. To enter the MIDI mode, press the [START/STOP] and [DEMO] buttons simultaneously, an “mm” will appear in the display to indicate the MIDI mode. BREAK/ TAPSTART START/ STOP DEMO A-B REPEAT • Pads and pedals do not sound while in the MIDI/Utility mode. BEAT mm To exit the MIDI mode, once again press the [START/STOP] and [DEMO] buttons simultaneously, the MIDI mode will be exited and the DD-50 will return to its normal play mode. Setting the Clock Connecting the DD-50, by MIDI cable, to an external MIDI device, such as a sequencer, time based functions (song playback, etc.) must be controlled by the internal clock (I) or an external clock (E). When the internal clock (I) is enabled, timing will be controlled by the DD-50’s internal clock. When an external clock (E) selected, time based functions will be controlled by the sequencer’s or computer’s clock. ● I (Internal) The DD-50’s clock is used as the timing clock. ● E (External) The external clock is used as the timing clock (If the clock is set to external without being connected to another MIDI device, the DD50’s Song Play or Demo functions will not respond). DRUM 1 BEAT 1 I Display the clock setting After entering the MIDI/Utility mode, press the [DRUM 1] button to see the current setting for the MIDI clock. 2 Set the Clock to External or Internal BEAT E To set the clock to “E” (external), turn the DIAL to the right (clockwise). To set the clock to “I” (internal), turn the DIAL to the left (counterclockwise). 3 Exit the MIDI/Utility mode After the clock is set, exit the MIDI/Utility mode. • The default MIDI clock setting is “I” (internal). 17 Using the MIDI/Utility Mode Local ON/OFF Setting the Local ON/OFF determines whether or not the internal voices respond to the notes you play on the DD-50’s pads. Setting this to OFF disconnects the DD-50’s pads from the voices. However, data produced by the DD-50 is transmitted via the MIDI OUT terminal. ● on (Local ON) The internal voices will be played and controlled by the DD-50 and its pads. Data received via MIDI will also be played by the DD-50. ● oF (Local OFF) Striking the pads will not produce any sound from the voices. However, data received via MIDI will be played by the DD-50. 1 DRUM 2 Display the Local On/Off Setting BEAT on After entering the MIDI/Utility mode, press the [DRUM 2] button and the current Local ON /OFF setting will appear in the display. 2 Set the Local On/Off BEAT To set to “on” (Local ON), turn the DIAL to the right (clockwise), to set to “oF”(Local OFF), turn the DIAL to the left (counter-clockwise). oF 3 Exit the MIDI/Utility mode After setting the Local ON/OFF, exit the MIDI/Utility mode. • Regardless of the Local ON/OFF setting, the DD-50’s performance data (including demo song data) is always sent to the MIDI OUT terminals for transmission to external MIDI devices. • The default Local ON/OFF setting is ON (Local ON). Setting the MIDI Transmit Channel Each of the pads/pedals (a total of 9) can be assigned to transmit on any of the 16 MIDI channels, or turned off (indicated as “oF” in the display). Also, song transmit channels are as shown below: Pad/Pedal Drum (Song) Bass (Song) Backing (Song) Pad/Pedal (Custom Song) 18 Transmit Channel 1-16 9, 10 11 (fixed) 12-15 (fixed) Default 10 9 — — 10, 16 16 Using the MIDI/Utility Mode 1 ASSIGN PAD BEAT KIT 10 Display the MIDI Transmit Channel Number After entering the MIDI/Utility mode, press the [PAD ASSIGN] button and the current Pad 1 transmit channel will be displayed. 2 BEAT Select a pad to be assigned a MIDI Transmit Number To select the pad you want to assign a MIDI transmit channel to, strike the pad. That pad’s currently selected MIDI transmit channel will appear in the display. 10 3 Set the MIDI Transmit Channel Number Turning the DIAL to the right (clockwise), MIDI transmit channel numbers will increase. • You can also select the MIDI transmit channel by striking the pad. Every time the pad is struck the MIDI transmit channel number will increase by 1. 4 Exit the MIDI/Utility mode After all pads/pedals have been assigned MIDI transmit channels, exit the MIDI/Utility mode. • For further information on what type of data is transmitted via MIDI, see the “MIDI Implementation Chart” (page 29), and try out the DD-50’s advanced MIDI features. ■ Setting the MIDI Transmit Channel . Drum (Song) Song performance data is transmitted on channel 9. You can change this transmit channel to channel 10 by using the procedure below: > First enter the MIDI/Utility mode by pressing both the [START/ STOP] and [DEMO] buttons simultaneously. Press the [SONG] button and the currently selected transmit channel will be displayed. BEAT 10 BEAT 9 BEAT 10 > Turning the DIAL, you can select either channel 9 or channel 10. After making a selection, exit the MIDI/Utility mode by pressing both the [START/STOP] and [DEMO] buttons simultaneously once again. Depending upon the setting of the Drum’s (Song) MIDI Transmit Channel, the MIDI Transmit Channel for the Pads/Pedals (Custom Song) will automatically change as follows: Display 9 10 Drum (Song) Pad/Pedal (Costom Song) 9 10 16 10 19 Using the MIDI/Utility Mode Setting the MIDI Note Number Each pad and pedal (9 total) can be assigned a specific MIDI note number anywhere from C-2 to G8. 1 ASSIGN BEAT PAD KIT After entering the MIDI/Utility mode, press the [KIT ASSIGN] button, the MIDI note number currently assigned to Pad 1 will appear in the display. E1 BEAT Display the MIDI Note Number 2 A1 Select the pad to be assigned a MIDI Note Number Strike any pad to see the currently assigned MIDI note number in the display. # (Sharp) —(Minus) BEAT Sharp notes are indicated by a dot on the upper left side of the display, minus values are indicated by a dot on the upper right side of the display. C2 3 Assign a MIDI Note Number To select the desired MIDI note number, turn the DIAL to the right (clockwise) and the MIDI note numbers will increase. Turn the DIAL to the left (counter-clockwise) and MIDI note numbers will decrease. • You can also select the MIDI note number by striking the pad. Every time the pad is struck, the value will increase by one. 4 Exit the MIDI/Utility mode After each pad is assigned a MIDI note number, exit the MIDI/Utility mode. • For information on transmit notes and voices, refer to the DD-50 “Drum Map” (note - voice, list) on page 27. • When the Pad Assign or Kit Assign is set, the MIDI Note Number will be applied to the preset value. If the Auto Kit Select is set to ON and another Song is selected, the MIDI Note Number will be applied to the preset value. Auto Kit Select is automatically turned off when a MIDI Note Number is changed. 20 Initialize The DD-50’s Custom Song, Custom Kit, and Panel Setting data are backed up so long as power is supplied to the DD-50 by means of batteries or an AC adaptor. Initialize is the term which refers to this data being restored to its original factory settings. To initialize the DD-50, follow the procedure below. POWER OFF ON > Turn the [POWER] switch OFF. DEMO POWER OFF > While holding the [DEMO] button, turn the [POWER] switch ON. The DD-50 will be initialized to its factory settings. “Cr” will appear in the display when the initialization process is complete. ON BEAT Cr ● Data Backup The following data will remain in memory, as long as batteries are installed or an AC adaptor is connected, even if the power is turned off. * Custom Song * Custom Kit * Reverb Depth * Auto Kit Selection * MIDI Transmit Channel for the PAD * MIDI Note Number for the PAD 21 Troubleshooting In many cases, problems or malfunctions that occur during use can be remedied easily. Please check the following list before deciding that your DD-50 is damaged. If the suggested remedy is ineffective, take the DD-50 to an authorized Yamaha dealer for proper diagnosis and repair. Do not attempt to repair this digital instrument by yourself as serious damage may occur. Problem Cause/Solution A buzz or click occurs momentarily when the DD-50 is turned ON or OFF This is a normal power surge noise that occurs when the POWER switch is operated The LED display is completely dark. When the pads are struck, the display is dark and returns to “00”. The batteries are low and should be replaced with a complete set of six new batteries immediately. Or, the optional AC adaptor PA-3 or PA-3B should be used to power the DD-50 (see page 3). No sound comes from the speakers. • The volume is set too low. Adjust the volume (see page 6). • A plug is inserted into the PHONES/AUX. OUT jack and should be taken out (see page 3). • The LOCAL ON/OFF is set to OFF. Set the LOCAL ON/OFF to ON (see page 18). • You are in the MIDI/Utility mode. Exit the MIDI/ Utility mode (see page 17). Striking two pads simultaneously results in one of the pads not sounding. Refer to “Adjusting the Pad’s Sensitivity” to resolve the problem (see page 30). Striking a pad results in other pads also sounding, though they were not struck. 22 The selected voice does not sound when the pad is struck. The desired voice has not been assigned to the pad. Use the PAD ASSIGN function to program the desired voice to the appropriate pad (see page 8). The custom pad voice assignments have disappeared or defaulted. The batteries are low and should be replaced with a complete set of six new batteries. Or, an optional AC adaptor (PA-3 or PA-3B) should be used to power the DD-50 (see page 3). The song or Demo does not start playback. The MIDI clock has been set to “E” (external). Change the MIDI clock setting to “I” (internal) (see page 17). “Cr” appears in the display when the POWER switch is turned ON, and backed up data has been erased. Backed up data is initialized if batteries are not installed or AC adaptor is disconnected while the POWER is turned OFF (see page 21). Data/Verzeichnisse und Spezifikationen/Données/Datos Drum Voice List / Drum Voice-Verzeichnis / Liste des voix de batterie / Lista de voces de batería Pad assign No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Voice Name Bass Drum Lo Bass Drum Mid Bass Drum Hi Bass Drum Rock Bass Drum Dance Bass Drum Jazz Snare Drum Light Snare Drum Lo Snare Drum Hi Snare Drum Rock Mid Snare Drum Rock Hi Snare Drum Dance Snare Drum Jazz Side Stick Open Rim Shot Sticks High Tom-H High Tom-L Mid Tom-H Mid Tom-L Low Tom-H Low Tom-L Rock H.Tom-H Rock H.Tom-L Rock M.Tom-H Rock M.Tom-L Rock L. Tom-H Rock L. Tom-L Jazz H. Tom-H Jazz H. Tom-L Jazz M. Tom-H Jazz M. Tom-L Jazz L. Tom-H Jazz L. Tom-L *Hi-Hat Closed/Open *Rock HH Closed/Open *Dance HH Closed /Open 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 Crash Cymbal-L Crash Cymbal-H Ride Cymbal Ride Cymbal Cup Chinese Cymbal Splash Cymbal Hand Clap Finger Snap Tambourine Rock Tambourine Cowbell Rock Cowbell Dance Cowbell Latin Cowbell Conga H Mute Conga H Open Conga L Conga Muffled Bongo H Bongo L Timbale H Timbale L Cascala Agogo H Agogo L Cabasa-1 Cabasa-2 Shaker Rock Shaker Claves Triangle Mute Triangle Open Guiro Short Guiro Long Cuica Mute Cuica Open Surdo Mute Surdo Open * By assigning Closed and Open Hi-Hat voices to both the Pad and Pedal, those voices can be controlled with the foot pedal as follows: • Strike the pad while pressing the Foot Pedal, the “Closed” Hi-Hat voice will sound. • Strike the pad without pressing the Foot Pedal, the “Open” Hi-Hat voice will sound. • Press the Foot Pedal without striking the pad, the Hi-Hat “Pedal” voice will sound. * Durch Zuordnen derselben Hi-Hat-Voice (HH Closed/Open) zu sowohl einem Pad und einem Pedal ist folgende Steuerung mit dem Pedal möglich: • Beim Anschlagen des Pads mit Pedalbetätigung wird der Klang eines geschlossenen “Closed” Hi-Hat erzeugt. • Beim Anschlagen des Pads ohne Pedalbetätigung wird der Klang eines offenen “Open” Hi-Hat erzeugt. • Betätigen Sie das Pedal, ohne das Pad anzuschlagen. Die Hi-Hat “Pedal” Voice erklingt dabei. * En affectant les voix de cymbale charleston fermée et ouverte (Closed and Open Hit-Hat) au pad et à la pédale, ces voix peuvent être contrôlées par la pédale, comme suit. • Frappez le pad tout en appuyant sur la pédale et le son de la cymbale charleston fermée (“Closed”) sortira. • Frappez le pad sans appuyer tout en appuyant sur la pédale et le son de cymbale charleston ouverteÅ (“Open”) sortira. • Appuyez sur la pédale sans frapper le pad, pour entendre la voix “Pédale” charleston. * Asignando voces de platillos abiertos y cerrados a los pulsadores y los pedales, podrá controlar tales voces con los pedales de la forma siguiente: • Si golpea el pulsador manteniendo pisado el pedal, sonará la voz de platillos cerrados (“Closed”). • Si golpea el pulsador sin pisar1 el pedal, sonará la voz de platillos abiertos (“Open”). • Pise el pedal sin golpear el pulsador: sonará la voz de “Pedal” de los platillos. 23 Data / Verzeichnisse und Spezifikationen / Données / Datos Small Pad 2 Small Pad 1 Pad 3 Pad 2 Pad 1 Pad 4 Small Pad 3 Pedal 1 Pedal 2 Drum Kit List / Drum Kit-Verzeichnis / Liste des kits de batterie / Lista No. 24 Kit Name Pad 1 Pad 2 Pad 3 Pad 4 0 Standard 1 8 Snare Drum Hi 16 High Tom-H 18 Mid Tom-H 20 Low Tom-H 1 Standard 2 7 Snare Drum Lo 17 High Tom-L 19 Mid Tom-L 21 Low Tom-L 2 Standard 3 6 Snare Drum Light 16 High Tom-H 18 Mid Tom-H 20 Low Tom-H 3 Standard 4 8 Snare Drum Hi 16 High Tom-H 18 Mid Tom-H 20 Low Tom-H 4 Standard 5 14 Open Rim Shot 17 High Tom-L 19 Mid Tom-L 21 Low Tom-L 5 Standard 6 13 Side Stick 16 High Tom-H 18 Mid Tom-H 20 Low Tom-H 6 Hard Rock 1 10 Snare Drum Rock Hi 22 Rock H.Tom-H 24 Rock M.Tom-H 26 Rock L.Tom-H 7 Hard Rock 2 9 Snare Drum Rock Mid 23 Rock H.Tom-L 25 Rock M.Tom-L 27 Rock L.Tom-L 8 Dance 1 11 Snare Drum Dance 16 High Tom-H 18 Mid Tom-H 20 Low Tom-H 9 Dance 2 6 Snare Drum Light 17 High Tom-L 19 Mid Tom-L 21 Low Tom-L 10 Samba Perc. 73 Surdo Mute 60 Agogo H 61 Agogo L 74 Surdo Open 11 Timbales 58 Timbale L 42 Splash Cymbal 59 Cascala 57 Timbale H 12 Conga 54 Conga Muffled 51 Conga H Mute 52 Conga H Open 53 Conga L 13 Jazz 1 12 Snare Drum Jazz 28 Jazz H.Tom-H 30 Jazz M.Tom-H 32 Jazz L.Tom-H 14 Jazz 2 7 Snare Drum Lo 29 Jazz H.Tom-L 31 Jazz M.Tom-L 33 Jazz L.Tom-L 15 Jazz 3 12 Snare Drum Jazz 28 Jazz H.Tom-H 39 Ride Cymbal 32 Jazz L.Tom-H 16 Twin Bass Drum 8 Snare Drum Hi 23 Rock H.Tom-L 25 Rock M.Tom-L 27 Rock L.Tom-L 17 Rock Perc. 58 Timbale L 46 Rock Tambourine 65 Rock Shaker 57 Timbale H 18 Ballad Perc. 67 Triangle Mute 66 Claves 45 Tambourine 68 Triangle Open 19 Cymbal 14 Open Rim Shot 38 Crash Cymbal-H 39 Ride Cymbal 37 Crash Cymbal-L Data / Verzeichnisse und Spezifikationen / Données / Datos de juegos de batería Small Pad 1 Small Pad 2 Small Pad 3 Pedal 1 Pedal 2 38 Crash Cymbal-H 39 Ride Cymbal 34 HH Open/Closed (Pedal 2 Off/On) 1 Bass Drum Mid 34 HH Pedal 34 HH Open/Closed (Pedal 2 Off/On) 37 Crash Cymbal-L 47 Cowbell 2 Bass Drum Hi 34 HH Pedal 38 Crash Cymbal-H 39 Ride Cymbal 35 Rock HH Open/Closed (Pedal 2 Off/On) 0 Bass Drum Lo 35 Rock HH Pedal 34 HH Open/Closed (Pedal 2 Off/On) 38 Crash Cymal-H 13 Side Stick 1 Bass Drum Mid 34 HH Pedal 38 Crash Cymbal-H 40 Ride Cymbal Cup 34 HH Open/Closed (Pedal 2 Off/On) 1 Bass Drum Mid 34 HH Pedal 42 Splash Cymbal 39 Ride Cymbal 34 HH Open/Closed (Pedal 2 Off/On) 0 Bass Drum Lo 34 HH Pedal 35 Rock HH Open/Closed (Pedal 2 Off/On) 38 Crash Cymbal-H 48 Rock Cowbell 3 Bass Drum Rock 35 Rock HH Pedal 38 Crash Cymbal-H 40 Ride Cymbal Cup 35 Rock HH Open/Closed (Pedal 2 Off/On) 3 Bass Drum Rock 35 Rock HH Pedal 36 Dance HH Open/Closed (Pedal 2 Off/On) 42 Splash Cymbal 49 Dance Cowbell 4 Bass Drum Dance 36 Dance HH Pedal 41 Chinese Cymbal 39 Ride Cymbal 36 Dance HH Open/Closed (Pedal 2 Off/On) 0 Bass Drum Lo 36 Dance HH Pedal 71 Cuica Mute 72 Cuica Open 63 Cabasa-2 48 Rock Cowbell 45 Tambourine 37 Crash Cymal-L 38 Crash Cymbal-H 50 Latin Cowbell 50 Latin Cowbell 66 Claves 55 Bongo H 56 Bongo L 57 Timbale H 50 Latin Cowbell 47 Cowbell 38 Crash Cymbal-H 39 Ride Cymbal 34 HH Open/Closed (Pedal 2 Off/On) 5 Bass Drum Jazz 34 HH Pedal 42 Splash Cymbal 39 Ride Cymbal 34 HH Open/Closed (Pedal 2 Off/On) 0 Bass Drum Lo 34 HH Pedal 34 HH Open/Closed (Pedal 2 Off/On) 38 CrashCymbal-H 13 Side Stick 5 Bass Drum Jazz 34 HH Pedal 38 Crash Cymbal-H 37 CrashCymal-L 34 HH Open/Closed (Pedal 2 Off/On) 1 Bass Drum Mid 1 Bass Drum Mid 38 Crash Cymbal-H 41 Chinese Cymbal 42 Splash Cymbal 48 Rock Cowbell 43 Hand Clap 64 Shaker 62 Cabasa-1 42 Splash Cymbal 47 Cowbell 44 Finger Snap 34 HH Open/Closed (Pedal 2 Off/On) 40 Ride Cymbal Cup 42 Splash Cymbal 2 Bass Drum Hi 34 HH Pedal 25 Data / Verzeichnisse und Spezifikationen / Données / Datos Song List / Song-Verzeichnis / Liste des morceaux / Lista de canciones No 49 Bossa Nova 50 51 Samba Salsa 52 53 Latin Rock Cha Cha 54 55 Mambo Rhumba 56 00 01 02 03 8 Beat 3 8 Beat 4 04 05 8 Beat 5 8 Beat 6 06 07 8 Beat 7 8 Beat 8 57 Afro Cuban Swing Swing 1 08 09 8 Beat 9 8 Beat 10 58 59 Swing 2 Swing 3 10 11 60 Swing 4 Others Swing Waltz 12 13 8 Beat 11 8 Beat 12 16 Beat 16 Beat 1 16 Beat 2 62 63 Waltz 3/4 Ballad 14 15 16 Beat 3 16 Beat 4 64 65 Swing Blues Blues 16 17 16 Beat 5 16 Beat 6 66 67 6/8 5/4 18 19 16 Beat 7 16 Beat 8 68 69 20 21 16 Beat 9 16 Beat 10 22 23 16 Beat 11 16 Beat 12 24 25 26 16 Beat 13 16 Beat 14 Dance Dance 1 27 28 Dance 2 Dance 3 29 30 Dance 4 Shuffle Shuffle 1 31 32 Shuffle 2 Shuffle 3 33 34 Shuffle 4 Shuffle 5 35 36 Shuffle 6 Shuffle 7 37 38 61 70 71 March 1 March 2 8 Beat 8 Beat Simple 8 Beat Rock 1 72 73 8 Beat Rock 2 Pop Ballad 1 74 75 Pop Ballad 2 Hard Rock 1 76 77 Hard Rock 2 Hard Rock 3 78 79 Dance Pop 1 Dance Pop 2 80 81 82 83 84 85 39 40 Shuffle 8 Shuffle 9 Slow Rock Slow Rock 1 Slow Rock 2 41 42 Slow Rock 3 Slow Rock 4 90 91 43 Slow Rock 5 Bounce Bounce 1 92 93 44 45 46 47 48 26 Song Name 8 Beat 8 Beat 1 8 Beat 2 Bounce 2 Bounce 3 Latin Reggae 1 Reggae 2 86 87 R&B 16 Beat 16 Beat Simple Fusion 1 Fusion 2 Funk Funk 1 Funk 2 Suffle Shuffle 1 Shuffle 2 88 89 Shuffle 3 Slow Rock Simple 16 Beat Shuffe 16 Beat Triplet Others Pop Reggae Bossa Nova 94 95 Samba Latin 96 97 Salsa 5/4 Organ 98 99 Fast Swing Big Band * Song No. 0-69 : Loop Type (Short) Song No. 70-99 : Sequence Type (Long) * Songs 0 bis 69 : Loop (kurz) Songs 70 bis 99 : Sequence (lang) * Morceaux n° 0 à 69 Morceaux n° 70 à 99 * N.° de canción 9-69 N.° de canción 70-99 (largo) : en boucle (court) : en séquence (long) : Tipo bucle (corto) : Tipo de secuencia Data / Verzeichnisse und Spezifikationen / Données / Datos Drum Map / Drum-Notenzurdnung / Topographie de batterie / Mapa de la batería Bank MSB# Program # Note# Note 13 C# -1 14 D -1 15 D# -1 16 E -1 17 F -1 18 F# -1 19 G -1 20 G# -1 21 A -1 22 A# -1 23 B -1 24 C 0 25 C# 0 26 D 0 27 D# 0 28 E 0 29 F 0 30 F# 0 31 G 0 32 G# 0 33 A 0 34 A# 0 35 B 0 36 C 1 37 C# 1 38 D 1 39 D# 1 40 E 1 41 F 1 42 F# 1 43 G 1 44 G# 1 45 A 1 46 A# 1 47 B 1 48 C 2 49 C# 2 50 D 2 51 D# 2 52 E 2 53 F 2 54 F# 2 55 G 2 56 G# 2 57 A 2 58 A# 2 59 B 2 60 C 3 61 C# 3 62 D 3 63 D# 3 64 E 3 65 F 3 66 F# 3 67 G 3 68 G# 3 69 A 3 70 A# 3 71 B 3 72 C 4 73 C# 4 74 D 4 75 D# 4 76 E 4 77 F 4 78 F# 4 79 G 4 80 G# 4 81 A 4 82 A# 4 83 B 4 84 C 5 85 C# 5 86 D 5 87 D# 5 88 E 5 127 0 Standard Rock Kit Surdo Mute Surdo Open Finger Snap Snare Drum Light Sticks Bass Drum Lo Open Rim Shot Bass Drum Mid Bass Drum Hi Side Stick Snare Drum Lo Hand Clap Snare Drum Hi Low Tom-L Hi-Hat Closed Low Tom-H Hi-Hat Pedal Mid Tom-L Hi-Hat Open Mid Tom-H High Tom-L Crash Cymbal-L High Tom-H Ride Cymbal Chinese Cymbal Ride Cymbal Cup Tambourine Splash Cymbal Cowbell Crash Cymbal-H Ride Cymbal Cup Bongo H Bongo L Conga H Mute Conga H Open Conga L Timbale H Timbale L Agogo H Agogo L Cabasa-1 Shaker Guiro Short Guiro Long Claves Cuica Mute Cuica Open Triangle Mute Triangle Open Cabasa-2 Conga Muffled Latin Cowbell Cascala <—— : The same voice as indicated in the columm to the left : No sound 127 16 Hard Rock Kit <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— Bass Drum Rock <—— Snare Drum Rock Mid <—— Snare Drum Rock Hi Rock L. Tom-L Rock HH Closed Rock L. Tom-H Rock HH Pedal Rock M.Tom-L Rock HH Open Rock M.Tom-H Rock H.Tom-L <—— Rock H.Tom-H <—— <—— <—— Rock Tambourine <—— Rock Cowbell <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— Rock Shaker <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— : Wie in der linken Spalte : Kein Klang 127 25 Dance Kit <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— Bass Drum Dance <—— Snare Drum Dance <—— Snare Drum Hi Low Tom. L Dance HH Closed Low Tom. H Dance HH Pedal Mid Tom. L Dance HH Open Mid Tom. H High Tom. L <—— High Tom. H <—— <—— <—— Tombourine <—— Dance Cowbell <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— Shaker <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— : La même voix, comme indiqué dans la colonne à gauche. : Aucune sonorité 127 32 Jazz Kit <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— Bass Drum Jazz <—— Snare Drum Jazz <—— Snare Drum Hi Jazz L. Tom-L Hi-Hat Closed Jazz L. Tom-H Hi-Hat Pedal Jazz M. Tom-L Hi-Hat Open Jazz M. Tom-H Jazz H. Tom-L <—— Jazz H. Tom-H <—— <—— <—— Tombourine <—— Cowbell <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— Shaker <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— <—— : La misma voz que la indicada en la columna de la izquierda : Sin sonido 27 Data / Verzeichnisse und Spezifikationen / Données / Datos Specifications / Technische Daten / Spécifications / Especificaciones Drum Pads 7 pads (125mm x 4, 88mm x 3), Touch Sensitive Maximum Polyphony 28 Drum Kits 20 Preset + 1 Custom Songs 100 Tracks 4 (DRUM 1/DRUM 2/BASS/BACKING) Custom Song 1 Song (approximately 600 notes) Drum Voices 75 Auxiliary Functions Track ON/OFF, TAP START, BREAK, A-B REPEAT, DEMO Panel Controls POWER ON/OFF, SONG VOLUME (large, small), PAD ASSIGN, KIT ASSIGN, SONG, TEMPO, MASTER VOLUME (large, small), REVERB, TRACK (DRUM 1/DRUM 2/BASS/BACKING), CLICK, DIAL, START/STOP, BREAK/TAP START, A-B REPEAT, DEMO LED Display Song/Drum Kit/Tempo etc. Connectors DC IN10-12 V PHONES/AUX OUT MIDI IN/OUT PEDAL 1/2 Main Amplifier 3W + 3W (EIAJ) Speaker 10 cm x 2 Power Source Six “C” size, SUM-2, R-14, or equivalent batteries (sold separately) DC 10-12V (Yamaha PA-3, PA-3B sold separately) Dimensions (WxDxH) 552 x 348 x 136 (21” 3/4 x 13” 2/3 x 5” 3/8) Weight 3.0 kg (6 Ibs. 10 oz) Supplied Accessories Drum stick x 2, Foot Pedal x 2, Owner’s Manual Optional Accessories Headphones HPE-150, HPE-3 AC Power Adaptor PA-3, PA3B Foot Switch FC4, FC5 * Specifications subject to change without notice. * Änderungen ohne Vorankündigung vorbehalten. * Sous toute réserve de modification des caractéristiques sans préavis. * Especificaciones sujetas a cambios sin previo aviso. 28 MIDI Implementation Chart / Implementierungstabelle / Table d'implémentation / Gráfico de implementación [Digital Percussion] Model: DD-50 Date: 1996. 3. 1 Version: 1.0 MIDI Implementation Chart Function Transmitted Recognized Remarks Basic Channel Default Changed 1~16 CH 1~16 CH 1~16 CH 1~16 CH Mode Default Messages Altered Mode 3 X ***************** Mode 3 X X : True voice 0~127 ***************** 13~96 13~96 Velocity Note on Note off O 9nH, v=1~127 X 9nH, v=0 O 9nH, v=1~127 X 9nH, v=0 After Touch key’s Ch’s X X X X O O O O O O O (*1) O O O X X O X X O O O O O O O O O O O O O Bank select MSB, LSB Modulation depth Data entry MSB, LSB Volume Pan Expression Sustain Ambience depth RPN data increment RPN data decrement RPN LSB, MSB All sound off Reset all controllers Program Change : True # O ***************** O 0~127 System Exclusive X X System : Song Position : Song Select Common : Tune X X X X X X System : Clock Real Time : Commands O O O O (*2) Aux X X O X X X O X Note Number Pitch Bender Control Change 0, 32 1 6, 38 7 10 11 64 91 96 97 100, 101 120 121 : Local ON/OFF : All Notes Off Messages : Active Sense : Reset Mode 1: OMNI ON, POLY Mode 3: OMNI OFF, POLY Mode 2: OMNI ON, MONO Mode 4: OMNI OFF, MONO *1 Value of Pan for each drum pad and foot pedal is not transmitted via MIDI. *1 Pan-Werte der einzelnen Pads und Pedale werden nicht über MIDI übertragen. *1 La valeur de Pan pour chaque pad de batterie et pour la pédale n’est pas transmise via MIDI. *1 El valor del efecto panorámico (Pan) para cada pulsador y pedal de batería no se transmite a través de MIDI. *2 The DD-50 can accept Start/Stop signals, received via MIDI, by setting the MIDI clock to “External”. *2 Das DD-50 spricht auf über MIDI empfangene Start/Stop-Signale an, wenn es auf externen MIDI-Taktgeber (“E”) gestellt ist. *2 Le DD-50 peut accepter les signaux Start/Stop reçus via MIDI, en réglant l’horloge MIDI sur “External (E)”. *2 El DD-50 puede aceptar señales de inicio/parada recibidas a través de MIDI, ajustando el reloj MIDI a “Externo (E)”. O: Yes X: No 29 Adjusting the Pad’s Sensitivity The factory default setting for pad sensitivity should provide you with trouble-free use. However, it is possible to adjust the pad’s sensitivity (0-3, factory default = 2) if you are experiencing one of the problems shown below. • Striking two pads simultaneously results in one of the pads not sounding. → Set the pad sensitivity level to 3. When two pads are simultaneously struck with this setting, both pads will sound together. However, if you strike the pads with too much force, the voice of a pad that is not struck may also sound. • Striking a pad results in other pads also sounding, though they were not struck. → Set the pad sensitivity level to 1. With this setting, pads that are not struck will become harder to sound. However, if you strike two pads simultaneously without enough force, one of the struck pads may not sound. → By setting the pad sensitivity level to 0, pads that are not struck will be even harder to sound. Setting Procedure 1Press the [START/STOP] and [DEMO] buttons simultaneously, “mm” will appear in the display. 2Press the large [SONG VOLUME] button to enter the pad sensitivity mode. The currently selected pad sensitivity setting will appear in the display. SONG VOLUME 3Turn the DIAL to set the pad sensitivity level (0-3). 4Once again, press the [START/STOP] and [DEMO] buttons simultaneously to exit the pad sensitivity mode and complete the setting procedure. • The pad sensitivity setting is retained in memory, even if the power is switched off, as long as batteries are installed or the power adaptor is connected to an AC outlet. If batteries are not installed and the power adaptor is not connected to an AC outlet, the sensitivity setting will return to its factory default setting (2). Einstellen der Pad-Empfindlichkeit Die werkseitige Standardeinstellung für die Pad-Empfindlichkeit sorgt im Normalfall für problemlosen Spieleinsatz. Sollte jedoch eines der im folgenden angeführten Probleme auftreten, können Sie die Pad-Empfindlichkeit (0 bis 3, Standardeinstellung = 2) höher oder niedriger einstellen. • Beim gleichzeitigen Anschlagen von zwei Pads erzeugt eines keinen Ton. → Stellen Sie die Pad-Empfindlichkeit auf “3” ein. Wenn Sie bei dieser Einstellung zwei Pads anschlagen, erzeugen beide Ton. Bei zu starkem Anschlagen kann es jedoch vorkommen, das auch andere Pads “mitschwingen”. • Beim Anschlagen eines Pads erzeugen andere Pads Ton, obwohl sie nicht berührt wurden. → Stellen Sie die Pad-Empfindlichkeit auf “1” ein. Bei dieser Einstellung reagieren die Pads weniger empfindlich. Wenn jedoch zwei Pads gleichzeitig mit zu wenig Kraft angeschlagen werden, klingt eines davon unter Umständen nicht. → Wenn die Pad-Empfindlichkeit auf “0” eingestellt wird, schwingen andere Pads nur bei extremer Anschlagstärke mit. Einstellvorgang 1Die Tasten [START/STOP] und [DEMO] gleichzeitig drücken. “mm” wird auf dem Display angezeigt. 2Die größere [SONG VOLUME]-Taste drücken, um auf Einstellmodus für Pad-Empfindlichkeit zu schalten. Die aktuelle Einstellung wird auf dem Display angezeigt. SONG VOLUME 3Am Wählrad drehen, um die gewünschte Empfindlichkeit einzustellen. 4Erneut die Tasten [START/STOP] und [DEMO] gleichzeitig drücken, um den Einstellmodus für Pad-Empfindlichkeit zu verlassen und den Einstellvorgang zu beenden. 30 • Die Pad-Empfindlichkeitseinstellung bleibt auch beim Ausschalten des Instruments gespeichert, solange Batterien eingelegt sind oder ein Netzadapter angeschlossen ist. Wenn keine Batterien eingelegt sind und der Netzadapter nicht angeschlossen ist, wird die Empfindlichkeit auf die werkseitige Standardeinstellung (2) zurückgesetzt. Réglage de la sensibilité des pads Le réglage par défaut en usine de la sensibilité des pads devrait vous permettre une utilisation sans problème. Cependant, il est possible de régler la sensibilité des pads (de 0 à 3, 2 étant le défaut) au cas où vous seriez confronté à l’un des problèmes mentionnés ci-dessous. • En frappant sur deux pads en même temps, vous n’entendez qu’un des pads. → Réglez le niveau de sensibilité de pad sur 3. Lorsque vous frappez sur deux pads en même temps avec ce réglage, les deux pads résonnent ensemble. Cependant, si vous frappez sur les pads avec une force trop grande, vous pouvez aussi entendre la voix d’un pad que vous n’avez pas touché. • Le fait de frapper un pad fait aussi résonner d’autres pads, même si vous ne les avez pas touchés. → Réglez le niveau de sensibilité de pad sur 1. Avec ce réglage, les pads qui ne sont pas frappés ont plus de mal à résonner. Cependant, si vous frappez sur les pads avec une force insuffisante, l’un des pads frappés peut ne pas résonner. → En réglant le niveau de sensibilité de pad sur 0, les pads que vous n’aurez pas touché résonneront encore moins. Procédure de réglage 1Appuyez en même temps sur les boutons [START/STOP] et [DEMO], pour faire apparaître “mm” sur l’écran. 2Appuyez sur le gros bouton [SONG VOLUME] pour entrer le mode de sensibilité de pad. Le réglage de sensibilité du pad actuellement sélectionné apparaît sur l’écran. SONG VOLUME 3Tournez la molette DIAL pour fixer le niveau de sensibilité du pad (0 à 3). 4Une fois de plus, appuyez en même temps sur les boutons [START/STOP] et [DEMO] pour sortir du mode de sensibilité de pad et terminer la procédure de réglage. • Le réglage de sensibilité de pad reste mémorisé, même quand l’alimentation est coupée, aussi longtemps que les piles sont en place ou que l’adaptateur secteur est branché dans une prise murale. Quand il n’y a plus de piles dans l’appareil et que l’adaptateur secteur est déconnecté à la prise murale, le réglage de sensibilité revient au réglage par défaut en usine (2). Ajuste de la sensibilidad de los pulsadores El ajuste de fábrica para la sensibilidad de los pulsadores debe proporcionar un funcionamiento sin problemas. Sin embargo, es posible ajustar la sensibilidad de los pulsadores (0-3, ajuste de fábrica = 2) si le ocurre alguno de los problemas que se mencionan a continuación. • Cuando se accionan dos pulsadores simultáneamente, uno de los pulsadores no suena. → Ajuste el nivel de sensibilidad de los pulsadores a 3. Cuando se accionan dos pulsadores simultáneamente con este ajuste, ambos pulsadores sonarán al mismo tiempo. Sin embargo, si acciona los pulsadores con demasiada fuerza, la voz de un pulsador que no se ha accionado también puede sonar. • Al accionar un pulsador, también suenan otros pulsadores, aunque no hayan sido accionados. → Ajuste el nivel de sensibilidad a 1. Con este ajuste, será más difícil que suenen los pulsadores que no han sido accionados. Sin embargo, si acciona dos pulsadores simultáneamente sin suficiente fuerza, es posible que no suene uno de los pulsadores. → Ajustando el nivel de sensibilidad de los pulsadores a 0, todavía será más difícil que suenen los pulsadores que no se accionan. Procedimiento de ajuste 1Presione simultáneamente los botones [START/STOP] y [DEMO], y “mm” aparecerá en el visualizador. 2Presione el botón grande [SONG VOLUME] para entrar en el modo de sensibilidad de los pulsadores. El ajuste de la sensibilidad de los pulsadores actualmente seleccionado aparecerá en el visualizador. SONG VOLUME 3Gire el DIAL para ajustar el nivel de sensibilidad de los pulsadores (0-3). 4Presione otra vez simultáneamente los botones [START/STOP] y [DEMO] para salir del modo de sensibilidad de los pulsadores y completar este procedimiento de ajuste. • El ajuste de la sensibilidad de los pulsadores se retienen en la memoria, incluso cuando se desconecta la alimentación, siempre y cuando haya pilas instaladas o el adaptador de CA esté enchufado a la toma de corriente. Si las pilas no están instaladas y el adaptador de alimentación no está enchufado a una toma de corriente, el ajuste retornará al ajuste de fábrica (2). 31 For details of products, please contact your nearest Yamaha or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 MIDDLE & SOUTH AMERICA MEXICO Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. ASIA ITALY Yamaha Musica Italia S.P.A., Home Keyboard Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 SPAIN Yamaha-Hazen Electronica Musical, S.A. Jorge Juan 30, 28001, Madrid, Spain Tel: 91-577-7270 PORTUGAL Valentim de Carvalho CI SA Estrada de Porto Salvo, Paço de Arcos 2780 Oeiras, Portugal Tel: 01-443-3398/4030/1823 GREECE Yamaha De Mexico S.A. De C.V., Departamento de ventas Javier Rojo Gomez No.1149, Col. Gpe Del Moral, Deleg. Iztapalapa, 09300 Mexico, D.F. Tel: 686-00-33 BRASIL Yamaha Musical Do Brasil LTDA. Ave. Reboucas 2636, São Paulo, Brasil Tel: 011-853-1377 PANAMA Philippe Nakas S.A. Navarinou Street 13, P.Code 10680, Athens, Greece Tel: 01-364-7111 SWEDEN Yamaha Scandinavia AB J. A. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 DENMARK Yamaha De Panama S.A. Edificio Interseco, Calle Elvira Mendez no.10, Piso 3, Oficina #105, Ciudad de Panama, Panama Tel: 507-69-5311 OTHER LATIN AMERICAN COUNTRIES AND CARIBBEAN COUNTRIES Yamaha Music Latin America Corp. 6101 Blue Lagoon Drive, Miami, Florida 33126, U.S.A. Tel: 305-261-4111 EUROPE THE UNITED KINGDOM Yamaha-Kemble Music (U.K.) Ltd. Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England Tel: 01908-366700 IRELAND Danfay Ltd. 61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin Tel: 01-2859177 GERMANY/SWITZERLAND Yamaha Europa GmbH. Siemensstraße 22-34, 25462 Rellingen, F.R. of Germany Tel: 04101-3030 YS Copenhagen Liaison Office Generatorvej 8B DK-2730 Herlev, Denmark Tel: 44 92 49 00 FINLAND Warner Music Finland OY/Fazer Music Aleksanterinkatu 11, P.O. Box 260 SF-00101 Helsinki, Finland Tel: 0435 011 NORWAY Narud Yamaha AS Grini Næringspark 17 N-1345 Østerås, Norway Tel: 67 14 47 90 ICELAND Skifan HF Skeifan 17 P.O. Box 8120 IS-128 Reykjavik, Iceland Tel: 525 5000 OTHER EUROPEAN COUNTRIES Yamaha Europa GmbH. Siemensstraße 22-34, 25462 Rellingen, F.R. of Germany Tel: 04101-3030 AFRICA AUSTRIA Yamaha Music Austria Schleiergasse 20, A-1100 Wien Austria Tel: 0222-60203900 THE NETHERLANDS Yamaha Corporation, International Marketing Division Nakazawa-cho 10-1, Hamamatsu, Japan 430 Tel: 053-460-2312 Yamaha Music Belgium Keiberg Imperiastraat 8, 1930 Zaventem, Belgium Tel: 02-7258220 FRANCE Yamaha Musique France, Division Claviers BP 70-77312 Marne-la-Valée Cedex 2, France Tel: 01-64-61-4000 Tom Lee Music Co., Ltd. 11/F., Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 730-1098 INDONESIA PT. Yamaha Music Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 KOREA Cosmos Corporation #131-31, Neung-Dong, Sungdong-Ku, Seoul Korea Tel: 02-466-0021~5 MALAYSIA Yamaha Music Malaysia, Sdn., Bhd. 16-28, Jalan SS 2/72, Petaling Jaya, Selangor, Malaysia Tel: 3-717-8977 PHILIPPINES Yupangco Music Corporation 339 Gil J. Puyat Avenue, P.O. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 SINGAPORE Yamaha Music Asia Pte., Ltd. Blk 17A Toa Payoh #01-190 Lorong 7 Singapore 1231 Tel: 354-0133 TAIWAN Kung Hsue She Trading Co., Ltd. No. 322, Section 1, Fu Hsing S. Road, Taipei 106, Taiwan. R.O.C. Tel: 02-709-1266 THAILAND Siam Music Yamaha Co., Ltd. 865 Phornprapha Building, Rama I Road, Patumwan, Bangkok 10330, Thailand Tel: 2-215-3443 THE PEOPLE’S REPUBLIC OF CHINA AND OTHER ASIAN COUNTRIES Yamaha Corporation, International Marketing Division Nakazawa-cho 10-1, Hamamatsu, Japan 430 Tel: 053-460-2317 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. 17-33 Market Street, South Melbourne, Vic. 3205, Australia Tel: 3-699-2388 NEW ZEALAND Yamaha Music Nederland Kanaalweg 18G, 3526KL, Utrecht, The Netherlands Tel: 030-2828411 BELGIUM HONG KONG MIDDLE EAST TURKEY/CYPRUS Yamaha Musique France, Division Export BP 70-77312 Marne-la-Valée Cedex 2, France Tel: 01-64-61-4000 OTHER COUNTRIES Yamaha Corporation, International Marketing Division Nakazawa-cho 10-1, Hamamatsu, Japan 430 Tel: 053-460-2312 HEAD OFFICE Yamaha Corporation, Electronic Musical Instrument Division [PK] 7 Nakazawa-cho 10-1, Hamamatsu, Japan 430 Tel: 053-460-3273 Music Houses of N.Z. Ltd. 146/148 Captain Springs Road, Te Papapa, Auckland, New Zealand Tel: 9-634-0099 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation, International Marketing Division Nakazawa-cho 10-1, Hamamatsu, Japan 430 Tel: 053-460-2317 M.D.G., EMI Division © 1996 Yamaha Corporation VU54270 Printed in Malaysia
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34

Yamaha DD-50 de handleiding

Categorie
Muziek drums
Type
de handleiding
Deze handleiding is ook geschikt voor