Yamaha MMP1 Gebruikershandleiding

Yamaha
Merk
Yamaha
Model
MMP1
Type
Gebruikershandleiding
MMP1 Firmware Update Guide 1
MMP1 Firmware Update Guide
Thank you for choosing a Yamaha product.
This guide explains how to update the MMP1 firmware and its built-in Dante
module firmware.
■ Precautions (Please be sure to read this section first!)
The user assumes full responsibility for the update.
Update the firmware components one device at a time.
Please note that the device may be damaged if you fail to follow these instructions properly,
or turn off the device or disconnect the cable while the update is in progress.
If the update fails, and the device still does not operate correctly even after you execute the
update once again, please contact your Yamaha dealer.
Yamaha Corporation owns exclusive copyrights for the MMP1 firmware, its update program,
and this guide.
Audinate owns exclusive copyrights for the Dante firmware and its update program.
It is prohibited to duplicate or modify the firmware, software or guides, in part or in their
entirety, without permission from the copyright owner.
The screen shots as shown in this guide are for instructional purposes only.
Dante is a registered trademark of Audinate.
Windows is a registered trademark of Microsoft ® Corporation in the United States and other
countries.
Mac is trademark of Apple Inc. registered in the U.S. and other countries.
The company names and product names in this document are the trademarks or registered
trademarks of their respective companies.
Software may be revised and updated without prior notice.
EN
MMP1 Firmware Update Guide 2
■ Checking the version number
You can check the MMP1 Editor and the MMP1 firmware version number from
the MMP1 Editor. You can also check the Dante firmware version number from
the Dante Controller.
MMP1 Editor ‒ Information screen
Dante Controller ‒ Device View screen
MMP1 Firmware Update Guide 3
■ Preparing for the update
In order to update, you will need to prepare the following items.
• A computer in which MMP1 Editor is operating normally
• An Ethernet cable (CAT5e or higher recommended. Straight or cross.)
• The latest version MMP1 Editor
• Firmware (Dante firmware is contained in the same compressed file as
MMP1 firmware.)
NOTE
Download the latest MMP1 Editor and the latest firmware from the following
URL: http://www.yamahaproaudio.com/
■ Update procedure sequence
Update each firmware component in the following sequence. If you plan to
update multiple MMP1 devices, repeat the sequence for each device.
* Refer to the section “MMP1 Compatibility” at the Yamaha Pro Audio site (below) for details
Dante firmware update requirements.
http://www.yamahaproaudio.com/
■ Updating the MMP1 firmware
When updating Dante firmware
is necessary:
When updating
Dante firmware is
unnecessary:
■ TCP/IP settings of computer
■ Install the Dante Firmware Update Manager
■ Updating the Dante firmware
The firmware update is completed.
MMP1 Firmware Update Guide 4
■ Updating the MMP1 firmware
Described below are the procedures to update the MMP1 firmware.
Uncompress the compressed file you downloaded in advance.
NOTICE
When the MMP1 firmware is updated, all data except Scenes and Snapshots are
erased. In the following instructions, transfer the data from the MMP1 to the
MMP1 Editor once, and then restore the data after updating the firmware.
1. Update the MMP1 Editor to the latest version.
2. Open the MMP1 Editor, and then log in as “Administrator.”
3. Connect the MMP1 to which you want to update the firmware with the
“MMP1 Editor” option.
4. Call up the Information screen on the MMP1 Editor, and then click
“Update.”
The “Save As” dialog box will be displayed.
MMP1 Firmware Update Guide 5
5. Specify the location to save the current settings, and then click
“Save.”
The “Open” dialog box will be displayed.
6. Select the firmware file “MMP1_firmxxx.mmpf, ” and then click
“Open.”
The characters “xxx” represent the firmware version number.
7. Confirm the firmware version number, and then click “Yes” if the
number is correct.
The update operation will begin.
An “Update has been completed.” is shown once update is completed.
8. Reboot the MMP1, then connect from the MMP1 Editor with the
“Editor MMP1” option.
If you accidentally connect with “CONNECT (MMP 1 → Editor),” open the
file saved in step 5 and connect again with “CONNECT (Editor → MMP 1).”
9. Confirm that the firmware version has been updated on the
Information screen.
The firmware update is now complete.
MMP1 Firmware Update Guide 6
■ TCP/IP settings of computer
Before you update the Dante firmware, you must change your computer’s
TCP/IP settings. After updating the firmware, return the TCP/IP settings to their
original settings.
Windows
1.
Open the “Network and Sharing Center” as described below.
Windows 7
Select [Start] → [Control Panel], then click or double-click [Network and
Sharing Center] or [View network status and tasks].
Windows 8.1 and Windows 10
Right-click [Start] → [Control Panel], then click or double-click [Network
and Sharing Center] or [View network status and tasks].
The “Network and Sharing Center” is displayed.
2. Click [Manage network connection] or [Change Adapter settings] from
the “Tasks” list located in the left side of “Network and Sharing
Center” window, then double-click [Local Area Connection].
The “Local Area Connection Status” dialog box will be displayed.
NOTE
• The “User Account Control” dialog box may appear. Click [Continue] or
[Yes].
• If the “Local Area Connection properties” dialog box appears, skip
ahead to step 4.
3. Click [Properties].
The “Local Area Connection properties” dialog box will be displayed.
NOTE
The “User Account Control” dialog box may appear. Click [Continue] or
[Yes].
MMP1 Firmware Update Guide 7
4. Select [Internet Protocol Version 4 (TCP/IPv4)], then click [Properties].
The “Internet Protocol Version 4(TCP/IPv4) Properties” dialog box will be
displayed.
5. Click [Obtain an IP address automatically].
6. Click [OK].
Mac
1.
Click [System Preferences] → [Network].
The “Network” dialog box will be displayed.
2. Click the service that you want to connect to the device.
If you're using the Ethernet port that's built into the Mac, click [Ethernet].
3. In “Configure IPv4,” choose [Using DHCP].
4. Click [Apply] button, then close “Network” dialog box.
MMP1 Firmware Update Guide 8
■ Install the Dante Firmware Update Manager
Before you update the Dante firmware, you must install the Dante Firmware
Update Manager.
Dante Firmware Update Manager installer is contained in the same
compressed file as MMP1 firmware.
Windows:
DanteFirmwareUpdateManager-x.x.x.x_windows.exe
Mac:
DanteFirmwareUpdateManager-x.x.x.x_osx.dmg
x.x.x.x represent the version number of the Dante Firmware
Update Manager.
Double-click the Dante Firmware Update Manager installer and follow the on-
screen instructions to install the firmware.
NOTE
• The Dante firmware does not operate normally if its path contains any
multi-byte character (including Japanese characters). If you use a directory
name containing any multi-byte character in your computer, store the
firmware update files in a directory that consists only of ASCII characters
(e.g. C:\temp).
• When installing the Dante Firmware Update Manager, temporarily disable
any running anti-virus software.
• The “User Account Control” dialog box or the “Windows Security” dialog
box may appear. In such case, click [Install this driver software anyway].
• In the middle of installation of the Dante Firmware Update Manager, you
may be prompted to install Bonjour. In such case, download the Bonjour
installer from the URL presented by the installer and install it.
MMP1 Firmware Update Guide 9
• You may be prompted to restart the computer after the installation is
complete. Before proceeding to update, restart the computer.
■ Updating the Dante firmware
Described below are the procedures to update the Dante module firmware
integrated in the MMP1 device.
When Dante firmware needs to be updated, execute the following procedures.
NOTE
• For details of the Dante Firmware Update Manager, refer to “AUD-MAN-
Firmware Update Manager” stored in the compressed file folder.
1. Connect the Dante [PRIMARY] connector on the rear panel of the
MMP1 device to the Ethernet connector on the computer using an
Ethernet cable.
Be sure to directly connect the computer and the MMP1 device, and do not
connect any other Dante device to the computer.
2. Start up the Dante Firmware Update Manager as follows.
Windows
Select “All programs” or “All apps” → “Audinate” → “Dante Firmware
Update Manager” → “Dante Firmware Update Manager.”
Mac
Double-click “Applications” → “Dante Firmware Update Manager.”
MMP1 Firmware Update Guide 10
NOTE
• Check in the title bar that the version number is 1.3.2 or higher.
• The “User Account Control” dialog box may appear. Click [Continue] or
[Yes].
3. Click [Update Dante Firmware].
4. Click [Browse] and select “FWUpdate_MMP1_vxxx_swyyy.dnt.” Then
click [Open].
xxx and yyy represent the firmware version number.
NOTE
The Dante firmware does not operate normally if its path contains any
multi-byte character (including Japanese characters). If you use a directory
name containing any multi-byte character in your computer, store the
firmware update files in a directory that consists only of ASCII characters
(e.g. C:\temp).
NOTICE
Be sure to ensure compatibility of the update files with MMP1. If update
files other than MMP1 are applied, the device will become inoperable. In
general, do not check the [Override Device Matching] option. If this option
is left unchecked, only devices that support the file can be selected,
ensuring that updating the device with invalid or wrong files is prevented.
5. Click [Next].
NOTE
Dante Firmware Update Manager may be blocked by the Windows Firewall.
Select the [Private Network] checkbox and click [Allow access].
MMP1 Firmware Update Guide 11
6. Check the MMP1 to update.
Check the version of the update files and the version number indicated in
the MMP1 line.
NOTE
If the MMP1 is not indicated, click [Refresh]. If it is still not indicated after
that, the computer and the MMP1 are not connected properly. Check that
the cable is not loose or disconnected, TCP/IP is properly configured, and
the MMP1 is powered on.
7. Click [Start].
The update operation will begin.
“Updating(n/m)” appears in the Status field during updating. “Done” is
displayed once update is completed.
NOTICE
Update takes 2 to 4 minutes. During the update operation, do not turn off
the power to the device or disconnect the cable. If update fails due to
MMP1 Firmware Update Guide 12
disconnection of the power cable during the update, or due to other
reasons, the device may become inoperative.
NOTE
If update is not completed after 5 minutes, or update failure indication
appears, exit the Dante Firmware Update Manager program without
turning the MMP1 power off, and restart the procedure from the step 4. If
update still fails, follow the instructions stated in “About Failsafe Mode” to
perform the recovery processing.
8. Restart the MMP1.
The firmware update is now complete.
MMP1 Firmware Update Guide 13
■ About Failsafe Mode
During normal operation, software must be loaded from a flash memory drive
during operations to use the Dante module integrated in the MMP1. However,
data in a flash memory drive may occasionally become corrupted, as with any
other storage device.
In many cases, such data corruption is caused by turning the MMP1 power off
during firmware upgrading.
The Dante module has a specially protected flash drive section in order to
recover from such a condition. When the main section is damaged, the
program stored in the protected area is activated and the Dante module goes
into “failsafe mode.”
To restore the Dante module in failsafe mode, a recovery image needs to be
sent from the Firmware Update Manager.
To check if the Dante module is in failsafe mode, use Dante Controller: the
respective device is displayed in red in the network grid view of the Dante
Controller (version 3.1.x or higher).
Described below are the procedures to recover the Dante module integrated in
the MMP1 device.
1. Turn off the power to the computer and the MMP1.
2. Separate the MMP1 from the Dante network.
3. Connect the Dante [PRIMARY] connector on the rear panel of the
MMP1 device to the Ethernet connector on the computer using an
Ethernet cable.
4. Turn the computer power on and login with administrative privileges.
5. Turn on the power to the MMP1.
6. Start up the Dante Firmware Update Manager as follows.
MMP1 Firmware Update Guide 14
Windows
Select “All programs” or “All apps” → “Audinate” → “Dante Firmware
Update Manager” → “Dante Firmware Update Manager.”
Mac
Double-click “Applications” → “Dante Firmware Update Manager.”
NOTE
The “User Account Control” dialog box may appear. Click [Continue] or
[Yes].
7. Click [Failsafe Recovery].
8. Check the detected MMP1.
9. Click [Start].
The recovery operation will begin.
10. When the “Recovery image loaded” dialog box appears, click [OK].
11. Exit the Dante Firmware Update Manager, and wait for two minutes
before turning off the power to the MMP1.
12. The correct Dante firmware now needs to be loaded.
Follow steps 2 through 8 described in “■ Updating the Dante firmware.”
Now recovery and firmware update are completed.
Manual Development Group
© 2018
Yamaha Corporation
Published 11/2018 YJHH-C0
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Yamaha MMP1 Gebruikershandleiding

Yamaha
Merk
Yamaha
Model
MMP1
Type
Gebruikershandleiding
Download PDF
rapport

in andere talen

Gerelateerde artikelen