EnglishDeutschFrançaisEspañol
Português
EN
JA
FR
DE
PT
ES
ZH
KO
VIBRAPHONE VARIABLE-SPEED DRIVER
YVD10
Owner’s Manual
Benutzerhandbuch
Mode d’emploi
Manual de instrucciones
Manual do Proprietário
Make sure to read the “PRECAUTIONS” on page 3.
Lesen Sie unbedingt die “VORSICHTSMASSNAHMEN” auf Seite 3.
Assurez-vous de lire “PRÉCAUTIONS D’USAGE” à la page 3.
Asegúrese de leer “PRECAUCIONES” en la página 3.
Certifique-se de ler “PRECAUÇÕES” na página 3.
2
(can_b_02)
1. IMPORTANT NOTICE: DO NOT MODIFY
THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the
USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regula-
tions, Part 15 for Class “B” digital devices. Compli-
ance with these requirements provides a reasonable
level of assurance that your use of this product in a
residential environment will not result in harmful
interference with other electronic devices. This
equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic dev ices.
Compliance with FCC regulations does not guaran-
tee that interference will not occur in all installations.
If this product is found to be the source of interfer-
ence, which can be determined by turning the unit
“OFF” and “ON”, please try to eliminate the problem
by usin
g one of the following measures:
Re
locate either this product or the device that is
being affected by the interference.
Utilize power outlets that are on different branch (cir-
cuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to co-axial type
cable.
If these corrective measures do not produce satis-
factory results, please contact the local retailer
authorized to distribute this type of product. If you
can not locate the appropriate retailer, please con-
tact Yamaha Corporation of America, Electronic
Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those prod-
ucts distributed by Yamaha Corporation of America
or its subsidiaries.
* This applies only to products distributed by Yamaha Corporation of America. (class B)
FCC INFORMATION (U.S.A.)
COMPLIANCE INFORMATION STATEMENT
(Supplier’s declaration of conformity procedure)
Responsible Party :
Yamaha Corporation of America
Address : 6600 Orangethorpe Ave.,
Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : VIBRAPHONE VARIABLE-
SPEED DRIVER
Model Name : YVD10
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference,
and
2) this device must accept any interference received
including interference that may cause undesired
operation.
CAN ICES-3 (B)/NMB-3(B)
* This applies only to products dis-
tributed by Yamaha Corporation of
America.
(FCC SDoC)
3
YVD10 Owner’s Manual
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even
death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions
include, but are not limited to, the following:
•This product contains no user-serviceable parts. Do not
open the units or attempt to disassemble or modify the
internal components in any way. If they should appear to
be malfunctioning, discontinue use immediately and
have it inspected by qualified Yamaha service
personnel.
•Repairs or part replacement should not be attempted
unless instructions are provided in the manual.
•Do not use or store the units in any of the following
locations. Doing so can cause fire or electrical shock.
- In places subject to high temperatures (near a heating
device or in direct sunlight, etc.).
- In places subject to low temperatures.
- In places where the units may be exposed to moisture
(bathroom, on wet floors, etc.) and excessive humidity.
- In places where the units may be exposed to rain.
- In places with excessive dust.
- In places subject to vibrations.
•Never insert or remove an electric plug with wet hands.
Improper grounding can result in electrical shock.
•Never put foreign objects (combustible objects, coins,
wire, etc.) or liquids (water, juice, etc.) in the units.
Doing so can cause fire or electrical shock.
•Only use the voltage specified as correct for the
instrument. The required voltage is printed on the name
plate of the instrument.
•Do not place the power cord of the AC adaptor near heat
sources such as heaters or radiators. Also, do not
excessively bend or otherwise damage the cord, or
place heavy objects on it.
•Use the specified AC adaptor only. Using the wrong AC
adaptor can result in damage to the units or overheating.
•Check the electric plug periodically and remove any dirt
or dust which may have accumulated on it.
•Do not connect the controller unit to an electrical outlet
using a multiple-connector. Doing so can result in
possibly cause overheating in the outlet.
•When removing the electric plug from the unit or an
outlet, always hold the plug itself and not the cord.
Pulling by the cord can damage it.
•Turn off the power switch and remove the electric plug
from the outlet when the units are not to be used for
extended periods of time, or during electrical storms.
•When one of the following problems occur, immediately
turn off the power switch and disconnect the electric
plug of the AC adaptor from the outlet. Then have the
device inspected by Yamaha service personnel.
- If the AC adapter or power cord becomes damaged.
- If foreign objects or liquids have gotten into a unit.
- If a unit gets wet (rain, etc.).
- If a unit operates abnormally or is broken.
PRECAUTIONS
Do not open
Handling
Power supply/AC adaptor
If you notice any abnormality
DMI-7 1/2
4
YVD10 Owner’s Manual
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or
others, or damage to the units or other property. These precautions include, but are not limited to,
the following:
•Treating the controller or driver roughly can damage the
internal circuit board, etc.
•Keep small parts out of the reach of infants. Your
children may accidentally swallow them.
•Do not place heavy objects on the units, and do not use
excessive force on the buttons, switches or connectors.
•Never touch the rotating pulleys. Doing so can result in
pinching your fingers, etc.
•Assemble the units in the proper sequence by following
the assembly instructions in this manual. Also, make
sure to tighten the screws or bolts regularly. Failure to
do so might result in damage to the units or even injury.
•Use the bolts that comes with the vibraphone.
•Do not place the units in an unstable position where it
might accidentally fall over.
•Before moving the instrument, remove all connected
cables, to prevent damage to the cables or injury to
anyone who might trip over them.
•When setting up the instrument, make sure that the AC
outlet you are using is easily accessible. If some trouble
or malfunction occurs, immediately turn off the power
switch and disconnect the plug from the outlet. Even
when the power switch is turned off, electricity is still
flowing to the product at the minimum level. When you
are not using the units for a long time, make sure to
unplug the power cord from the wall AC outlet.
•When moving the instrument, move it gently avoiding
shocks and impacts. The instrument is sensitive to
shocks and may become damaged.
Always turn the power off when the instrument is not in use.
Handling
Assembly
Transportation and Installation
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument.
DMI-7 2/2
5
YVD10 Owner’s Manual
NOTICE
• Do not use the units in locations with poor ventilation.
•Parts such as switches, volume control, jacks, are called consumable parts and their
function will deteriorate over time. The level of deterioration will vary depending upon
the conditions under which the units are used. However, deterioration cannot be
completely avoided. When replacing consumable parts, please contact your dealer
or qualified Yamaha service personnel.
• Do not place vinyl, plastic or rubber objects on the instrument, since this might dis-
color the units.
• When cleaning the units, wipe with a soft and dry cloth. Do not use paint thinners,
solvents, alcohol, cleaning fluids, or chemical-impregnated wiping cloths.
INFORMATION
• The illustrations as shown in this manual are for instructional purposes only, and may
appear somewhat different from those on your instrument.
• The company names and product names in this manual are the trademarks or regis-
tered trademarks of their respective companies.
(rear_en_01)
The model number, serial number, power requirements, etc., may be found on or
near the name plate, which is at the rear of the unit. You should note this serial
number in the space provided below and retain this manual as a permanent
record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
6
YVD10 Owner’s Manual
Introduction
Thank you for purchasing the Yamaha VIBRAPHONE VARIABLE-SPEED DRIVER
YVD10. The VIBRAPHONE VARIABLE-SPEED DRIVER is a motorized drive unit that
rotates the fans of the vibraphone. To get full use of this product and enjoy optimal per-
formance, please read this owner’s manual carefully before using the units.
After you have read the manual, keep it in a safe and handy place for future reference.
Part Names and Functions
q POWER switch
Turns the power on ( ) and off.
w Motor speed slider (SLOW 1–6
FAST)
Adjusts the fan speed.
e LED indicator
Lights in green when the power is
turned on and flashes while fans are
rotating.
Lights in red when an error has
occurred. To recover from an error,
remove the factors that hinder fan
rotation, and then press the r
START/STOP button.
r START / STOP button
Starts and stops fan rotation.
t Power jack ( )
y Driver connection terminal
u AC adaptor (sold separately)
12V
re w q y
t
u
Controller (player side)
Controller (right side)
Driver
(player side)
7
YVD10 Owner’s Manual
Confirmation of Packing Contents
The shipping package of your YVD10 should contain the parts shown below.
Before assembling the instrument, confirm that all parts are included as listed.
* If a part is missing, please contact your dealer or qualified Yamaha service personnel.
q Owner’s Manual
(this document) × 1
w Controller × 1
e Driver × 1
r Fan belt × 2
t Yamaha representative or the
authorized distributor list × 1
y Legal compliance leaflet × 1
Assembly
1.
Attach the controller.
(1) Hook the notch at the upper part
of the controller to the screw that
protrudes from the lower front of the
treble side of the vibraphone, and
then (2) secure the hole on the other
side of the upper of the controller
using the bolt attached to the vibra-
phone.
2. Attach the driver.
With the pulley to your right side and
the connector end of the cable fac-
ing you, (1) insert the driver into the
driver attachment from below, and
then (2) secure it with the cup head
square neck bolt and the wing nut.
(1)
(2)
(1)
(2)
Pulley
8
YVD10 Owner’s Manual
3. Connect the driver and the con-
troller.
Connect the driver cable to the driver
connection terminal on the control-
ler. Also, align the flat shape of the
connector of the cable with the
mark printed on the controller.
* Be careful not to break the pins of the cable.
4. Set the fan belt.
First, wrap the fan belt around the
vibraphone (fan) pulley, and then
twist and hook the fan belt on the
pulley of the driver.
* Order a replacement fan belt (sold sepa-
rately) using the following number. When
ordering, please contact your dealer or quali-
fied Yamaha service personnel. Replace the
two fan belts at the same time.
The assembly is now complete.
If the distance between pulleys is too
wide to fit the belt, or if it is too nar-
row and the belt slips, first loosen the
wing nut and then adjust the tension
of the belt. After adjusting the ten-
sion, tighten the wing nut firmly.
12V
Controller
Driver
Cable
Part No. W5128070
Part name Fan belt
Fan belt 3ØL236
When using for a long time, the fan belt will stretch
and the pulley will run idle. If this happens, adjust
the tension of the fan belt by slightly lowering the
mounting position of the driver unit.
Fan side
Pulley Fan belt
Fan belt Pulley Cup head square
neck bolt
Driver side
NOTE
9
YVD10 Owner’s Manual
Power Supply
Prepare a separately sold AC adaptor.
1. Connect the DC plug of the AC
adaptor to the power jack
().
2. Connect the electric plug of the
AC adaptor to an outlet.
12V
1
2
Controller
AC adaptor
DC 12V IN
* In order to prevent the DC plug from
coming out unintentionally, we recom-
mend wrapping the power cord once
around the body leg (as shown) before
connecting.
AC
10
YVD10 Owner’s Manual
Specifications
Rated speed: 30–145 RPM
Power consumption: 3 W
Operating temperature range: 5–40 degrees Celsius
Dimensions (W × H × D)
Controller: 172 × 67 × 43 mm
Driver: 92.8 × 65.5 × 183 mm (excluding the cable; approx. 250 mm)
Weight: 0.6 kg (including the fan belt)
Included accessories: Fan belt
Separately sold accessories (May not be available depending on your area):
AC adaptor (PA-130: output DC12V 1.0A, PA-130B: output DC12V 0.7A, PA-150B:
output DC12V 1.5A or an equivalent recommended by Yamaha)
* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest
manual, access the Yamaha website and then download the manual file. Since specifications, equipment or
separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.
(weee_eu_en_02)
Information for users on collection and disposal of old equipment:
This symbol on the products, packaging, and/or accompanying documents
means that used electrical and electronic products should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products, please take
them to applicable collection points, in accordance with your national legisla-
tion.
By disposing of these products correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please
contact your local municipality, your waste disposal service or the point of
sale where you purchased the items.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact
your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union:
This symbol is only valid in the European Union. If you wish to discard these
items, please contact your local authorities or dealer and ask for the correct
method of disposal.
VDE9920
Manual Development Group
©2019 Yamaha Corporation
Published 12/2019
2019
12
POOD-A1
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Yamaha Vibraphone Variable-Speed Driver YVD10 Handleiding
- Type
- Handleiding
- Deze handleiding is ook geschikt voor
in andere talen
- English: Yamaha Vibraphone Variable-Speed Driver YVD10 User manual
- italiano: Yamaha Vibraphone Variable-Speed Driver YVD10 Manuale utente
- français: Yamaha Vibraphone Variable-Speed Driver YVD10 Manuel utilisateur
- español: Yamaha Vibraphone Variable-Speed Driver YVD10 Manual de usuario
- Deutsch: Yamaha Vibraphone Variable-Speed Driver YVD10 Benutzerhandbuch
- dansk: Yamaha Vibraphone Variable-Speed Driver YVD10 Brugermanual
- čeština: Yamaha Vibraphone Variable-Speed Driver YVD10 Uživatelský manuál