Yamaha RX-V800RDS Handleiding

Categorie
Ontvanger
Type
Handleiding
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia ID
V624940
RX-V800RDS
Natural Sound AV Receiver
Ampli-tuner audio-vidéo
G B
RX-V800RDS
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
0100V800RDS(GB)-cv1/4 8/29/0, 10:02 AM1
II
II
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place with at least 30 cm on the top, 20 cm on the
right and left, and 10 cm at the back of this unit
— away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds. To prevent fire or electrical
shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in a environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 On the top of this unit, do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
Containers with liquid in them, as they may cause
electrical shock to the user and/or damage to this
unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation.
If the temperature inside this unit rises, it may
cause fire, damage to this unit, and/or personal
injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an electrical
storm.
14 Take care of this unit so that no foreign objects and/
or liquid drops inside this unit.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
15 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
16 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
17 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
18 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
Special Instructions for U.K.
Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED
IN ACCORDANCE WITH THE FOLLOWING
CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured BLUE must be connected
to the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured
BROWN must be connected to the terminal which is
marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
CAUTION
1
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTENTS
INTRODUCTION
INTRODUCTION
CONTENTS ........................................................... 1
FEATURES ............................................................ 2
GETTING STARTED ........................................... 3
Checking the Package Contents ............................... 3
Installing Batteries in the Remote Control ............... 3
CONTROLS AND FUNCTIONS ........................ 4
Front Panel ............................................................... 4
Remote Control ........................................................ 6
Description of the Numeric Buttons......................... 7
Using the Remote Control ........................................ 8
Front Panel Display .................................................. 9
Rear Panel .............................................................. 10
PREPARATION
SPEAKER SETUP .............................................. 11
Speakers to Be Used ............................................... 11
Speaker Placement ................................................. 11
CONNECTIONS ................................................. 12
Before Connecting Components ............................ 12
Connecting Audio Components ............................. 12
Connecting Video Components .............................. 14
Connecting the Speakers ........................................ 16
Connecting to an External Amplifier ..................... 18
Connecting an External Decoder ............................ 18
IMPEDANCE SELECTOR Switch ....................... 19
Connecting the Power Supply Cords ...................... 19
ON-SCREEN DISPLAY (OSD) ......................... 20
OSD Modes ............................................................ 20
Selecting the OSD Mode ........................................ 20
SPEAKER MODE SETTINGS ......................... 21
Summary of SPEAKER SET Items
1A through 1E .................................................... 21
ADJUSTING THE SPEAKER
OUTPUT LEVELS ......................................... 22
Before You Begin ................................................... 22
Using the Test Tone (TEST DOLBY SUR.) .......... 22
BASIC OPERATION
BASIC PLAYBACK ............................................ 24
Input Modes and Indications .................................. 26
Selecting a Sound Field Program ........................... 28
Normal Stereo Reproduction .................................. 29
TUNING ............................................................... 30
Connecting the Antennas ........................................ 30
Automatic (or Manual) Tuning .............................. 31
Presetting Stations .................................................. 32
Tuning in to a Preset Station .................................. 33
Exchanging Preset Stations .................................... 34
RECEIVING RDS STATIONS .......................... 35
Description of RDS Data ........................................ 35
Changing the RDS Mode ....................................... 35
PTY SEEK Function .............................................. 36
EON Function ........................................................ 37
BASIC RECORDING ......................................... 38
ADVANCED OPERATION
SET MENU .......................................................... 39
Adjusting the Items on the SET MENU................. 39
1 SPEAKER SET (speaker mode settings) ........... 40
2 LOW FRQ TEST ............................................... 42
3 L/R BALANCE (balance of the
left and right main speakers) .............................. 43
4 HP TONE CTRL (headphone tone control) ....... 43
5 CENTER GEQ (center graphic equalizer) ......... 43
6 INPUT RENAME .............................................. 44
7 I/O ASSIGNMENT ............................................ 44
8 INPUT MODE (initial input mode) ................... 44
9 PARAM. INI (parameter initialization) ............. 44
10 DOLBY D. SET (Dolby Digital set) ............... 45
11 DTS LFE LEVEL ............................................ 45
12 6.1/ES AUTO ................................................... 45
13 SP DELAY TIME ............................................ 46
14 DISPLAY SET ................................................. 46
15 MEMORY GUARD ......................................... 46
ADJUSTING THE LEVEL OF THE EFFECT
SPEAKERS ...................................................... 47
SLEEP TIMER .................................................... 48
Setting the Sleep Timer .......................................... 48
Canceling the Sleep Timer ..................................... 48
REMOTE CONTROL FEATURES .................. 49
Selector Dial ........................................................... 49
Commonly Used Buttons in Any Position of the
Selector Dial ....................................................... 50
Controlling the Components
Connected to This Unit ...................................... 50
Button Names and Functions in Each Position ...... 51
Setting the Manufacturer Code .............................. 54
Programming a New Remote Control Function
(Learn Feature) ................................................... 55
Returning to the Factory Setting ............................ 56
ADDITIONAL INFORMATION
SOUND FIELD PROGRAM ............................. 57
Hi-Fi DSP Programs ............................................... 57
CINEMA DSP Programs ....................................... 58
MOVIE THEATER Programs ................................ 61
SOUND FIELD PROGRAM PARAMETER
EDITING ......................................................... 62
What is a sound field? ............................................ 62
Sound Field Program Parameters ........................... 62
Changing Parameter Settings ................................. 63
Resetting a Parameter to the Factory-set Value ...... 63
Digital Sound Field Parameter Descriptions .......... 64
APPENDIX
TROUBLESHOOTING ...................................... 68
SPECIFICATIONS ............................................. 73
2
Thank you for selecting this YAMAHA AV receiver.
FEATURES
Other Features
96-kHz/24-bit D/A Converter
SET MENU which Provides You with 15 Items
for Optimizing This Unit for Your Audio/Video
System
Test Tone Generator for Easier Speaker Balance
Adjustment
6-Channel External Decoder Input for Other
Future Formats
BASS EXTENSION Button for Reinforcing
Bass Response
On Screen Display Function Helpful in
Controlling This Unit
S Video Signal Input/Output Capability
Component Video Input/Output Capability
Optical and Coaxial Digital Audio Signal Jacks
Sleep Timer
Remote Control with Preset Manufacturer Codes
and Learning Capability
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this
manual.
Built-in 5-Channel Power Amplifier
Minimum RMS Output Power
(0.04% THD, 20 Hz 20 kHz)
Main: 100 W + 100 W (8 )
Center: 100 W (8 )
Rear: 100 W + 100 W (8 )
Multi-Mode Digital Sound Field
Processing
Digital Sound Field Processor (DSP)
Dolby Pro Logic Decoder
Dolby Digital/Dolby Digital Matrix 6.1 Decoder
DTS/DTS ES Decoder
CINEMA DSP: Combination of YAMAHA DSP
Technology and Dolby Pro Logic, Dolby Digital
or DTS
Virtual CINEMA DSP
SILENT CINEMA DSP
Sophisticated AM/FM Tuner
40-Station Random Access Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability (Preset
Editing)
Multi-Functions for RDS Broadcast Reception
Manufactured under license from Dolby Laboratories.
Dolby, AC-3, Pro Logic, Surround EX and the double-D
symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. ©1992-1997 Dolby
Laboratories, Inc. All rights reserved.
Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 and other world-wide patents issued and
pending. DTS, DTS Digital Surround and DTS ES are
trademarks of Digital Theater Systems, Inc. Copyright 1996
Digital Theater Systems, Inc. All Rights Reserved.
3
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
Remote control
Installing Batteries in the Remote
Control
Insert the batteries in the correct direction by aligning the
+ and marks on the batteries with the polarity markings
(+ and ) inside the battery compartment.
Notes on batteries
Change the batteries periodically.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
GETTING STARTED
Checking the Package Contents
Check your package to make sure it has the following items.
Manganese batteries (4)
(AAA, R03, UM-4)
Indoor FM antenna
AM loop antenna
Quick Reference Card
Changing batteries
As the batteries lose power, the operating range of the
remote control decreases and the indicator does not flash
or its light becomes dim. When you notice any of these
conditions, change all of the batteries.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
Note
If the batteries have leaked, dispose of them immediately.
Avoid touching the leaked material or letting it come into
contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
1
2
3
A/B/C/D/E
Quick Reference Card
75-ohm/300-ohm
antenna adapter
(U.K. model only)
4
CONTROLS AND FUNCTIONS
Front Panel
1 STANDBY/ON
Turns on and sets this unit in the standby mode. When
you turn on this unit, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.
Standby mode
In this mode, this unit consumes a small amount of
power to receive infrared-signals from the remote
control.
2 Remote control sensor
Receives signals from the remote control.
3 Front panel display
Shows information about the operational status of this
unit (see page 9).
4 INPUT MODE
Selects the mode of input for sources that send two or
more types of signals to this unit (see page 26).
You cannot control the input mode when you select 6CH
INPUT as the input source.
5 INPUT l / h
Selects the input source (DVD, D-TV/LD, CBL/SAT,
VCR 1, VCR 2/DVR, V-AUX, PHONO, CD, TUNER,
CD-R, MD/TAPE) you want to listen to or watch.
6 VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
7 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
The source selected by pressing 6CH INPUT takes
priority over the source selected with INPUT l / h (or
the input selector buttons).
8 SPEAKERS A/B
Turn on or off the set of main speakers connected to the A
and/or B terminals on the rear panel.
9 BASS EXTENSION ON/OFF
When pushed in (ON), this feature boosts the bass
frequency of the left and right main channels by +6 dB
(60 Hz) while maintaining overall tonal balance. This
boost is useful if you do not use a subwoofer.
However, this boost may not be noticeable if 1B MAIN
SP on the SET MENU is set to SMALL and 1D LFE/
BASS OUT is set to SWFR.
0 PROCESSOR DIRECT ON/OFF
When pushed in (ON), BASS, TREBLE, and BASS
EXTENSION are bypassed, eliminating any alteration of
the original signal.
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
1
2
34
56
7
89 0
qw
e
r
ty
h
g
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
iopa
sdf
u
5
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
a RDS MODE/FREQ
When an RDS station is received, press this button to
change the display mode among the PS mode, PTY mode,
RT mode, CT mode (if the station offers those RDS data
services) and/or frequency display mode in turn.
s EON
Press this button to select the desired program type
(NEWS, INFO, AFFAIRS, SPORT) when you want to
tune in to a radio program of that type automatically.
d PTY SEEK MODE
Press this button to set the unit in the PTY SEEK mode.
f PTY SEEK START
Press this button to begin searching for a station after the
desired program type has been selected in the PTY SEEK
mode.
g BASS
Adjusts the low-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the low-frequency response.
h TREBLE
Adjusts the high-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the high-frequency response.
Note
If you increase or decrease the high-frequency or the low-
frequency sound to an extreme level, the tonal quality from the
center and rear speakers may not match that of the left and
right main speakers.
Opening and closing the front
panel door
When you are not operating the controls behind the front
panel door, close the door.
D
I
G
I
T
A
L
q EFFECT
Switches the effect speakers (center and rear) on and off.
If you turn off the output of these speakers by using
EFFECT, all Dolby Digital and DTS audio signals except
for the LFE channel are directed to the main left and right
channels.
When Dolby Digital or DTS signals are mixed, the left
and right main channel signal levels may not match.
w A/B/C/D/E
Selects one of the 5 preset station groups (A to E).
e PROGRAM l / h
Selects the DSP program (see page 28).
r PRESET/TUNING l / h
Selects preset station number 1 to 8 when the colon (:)
appears next to the band indication on the front panel
display, and selects the tuning frequency when the colon
(:) does not appear.
t PHONES jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the OUTPUT jacks or to the speakers.
y VIDEO AUX jacks
Inputs audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input
source.
u PRESET/TUNING (EDIT)
Switches the function of PRESET/TUNING l / h (the
colon (:) turns on or off) between selecting a preset
station number and tuning.
This button is also used to exchange the assignment of
two preset stations with each other.
i FM/AM
Switches the reception band between FM and AM.
o MEMORY (MANL/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
p TUNING MODE (AUTO/MANL MONO)
Switches the tuning mode between automatic and manual.
To select the automatic tuning mode, press this button so
that the AUTO indicator lights up on the front panel
display. To select the manual tuning mode, press this
button so that the AUTO indicator does not light up.
To open, press gently on the lower part of the panel.
6
CONTROLS AND FUNCTIONS
A/B/C/D/E
TV INPUT
TV VOLUME
TV POWER
EFFECT
w
e
1
2
3
4
5
6
7
8
0
q
9
r
t
y
u
i
Remote Control
This section describes the basic operation of this unit with
the remote control. First, set the selector dial to the AMP/
TUN position. See REMOTE CONTROL FEATURES
on pages 49 to 56 for full details.
Select the
AMP/TUN
position.
See page 7.
1 DSP
Switches the function of the numeric buttons to the DSP
program selector (see page 7).
2 Indicator window
Shows the name of components which can be controlled.
3 Numeric buttons (Input selector buttons)
These buttons select the input source.
See pages 7 and 8 for the numeric buttons.
4 TEST
Outputs the test tone.
5 ON SCREEN
Selects the on-screen display (OSD) mode for your video
monitor.
6 j / i
Adjust DSP program parameters and SET MENU items.
7 LEVEL
Selects the effect speaker channel (center, rear and
subwoofer) so you can adjust their output level
independently.
8 SLEEP
Sets the sleep timer.
9 INPUT
Switches the function of the numeric buttons to the input
selector (see page 7).
0 Indicator
Flashes while the remote control is sending signals.
q Selector dial
Turn this dial to select the position for the component to
be controlled. (The proper code must be set up for your
component. See Setting the Manufacture Codes on
page 54.) When the position is selected, the remote
control is set to that component operation mode.
w A/B/C/D/E, PRESET/+
These buttons are used to select a preset station.
A/B/C/D/E: To select one of 5 preset station groups (A
to E)
PRESET /+: To select a preset station number (1 to 8)
e u/d
Select DSP program parameters and SET MENU items.
r SET MENU
Enters the SET MENU.
t POWER
Turns on the power of this unit.
y STANDBY
Sets this unit in the standby mode.
7
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
A B
u VOLUME +/
Increases or decreases the volume level.
i MUTE
Mutes the sound. Press again to restore the audio output
to the previous volume level.
EFFECT
Switches the effect speakers (center and rear) on and off
in the following cases:
When the selector dial is set to the DSP/TUN position.
While the indicator is lit for about 3 seconds after
pressing DSP.
Description of the Numeric
Buttons
The numeric buttons function in various ways depending
on the position of the selector dial or the combination of
other instructions.
When selecting an input source
Input selector
buttons
1 Press INPUT regardless of the position of
the selector dial.
The indicator lights up for about 3 seconds.
2 You can select an input source with the
numeric buttons while the indicator is lit.
When selecting a DSP program
and turning on or off the effect
speakers (center and rear)
DSP program
group buttons
A
1 Press DSP regardless of the position of the
selector dial.
The indicator lights up for about 3 seconds.
2 You can select a DSP program with the
numeric buttons, turn on or off the effect
speakers (center and rear) by pressing
EFFECT and turn on or off the Dolby Digital
Matrix 6.1 or DTS ES decoder by pressing
6.1/ES while the indicator is lit.
B
1 Set the selector dial to the DSP/TUN
position.
2 You can select a DSP program directly with
the numeric buttons, turn on or off the effect
speakers (center and rear) by pressing
EFFECT and turn on or off the Dolby Digital
Matrix 6.1 or DTS ES decoder by pressing
6.1/ES.
8
CONTROLS AND FUNCTIONS
STANDBY
/ON
+
+
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
30° 30°
When selecting a preset station
number
1 Set code number 0023 in the AMP/TUN (or
DSP/TUN) position.
See page 54 for setting the code.
2 Set the selector dial to the AMP/TUN (or
DSP/TUN) position.
3 You can select a preset station number
directly with the numeric buttons (1 to 8).
See page 34.
Using the Remote Control
Approximately 6 m (20 feet)
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
Handling the remote control
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
high humidity or temperature such as near a heater,
stove or bath;
dusty places; or
in places subject to extremely low temperatures.
9
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
DIGITAL
DTS MOVIE THEATER 1
2
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
DSP
6.1/ES
PCM
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
VOLUME
dB
ms
SLEEP
1 234 wq87
apio
6
uyre t
09 5
Front Panel Display
1 t indicator
Lights up when the built-in DTS decoder is on.
2 VIRTUAL indicator
Lights up when using Virtual CINEMA DSP (see
page 29).
3 g and o indicators
Light up according to the type of Dolby signals this unit
is reproducing. g lights up when the built-
in Dolby Digital decoder is on. o lights up
when the built-in Dolby Pro Logic decoder is on.
4 x indicator
Lights up when you select a DSP program.
5 DSP program indicators
The name of the selected DSP program lights up when
the ENTERTAINMENT, MOVIE THEATER 1, MOVIE
THEATER 2 or q/DTS SURROUND DSP program is
selected.
6 PTY HOLD indicator
Lights up while searching for stations in the PTY SEEK
mode.
7 RDS mode indicators
The name(s) of the RDS data offered by the currently
received RDS station light(s) up. Illumination of the red
indicator next to the RDS data name shows that the
corresponding RDS mode is now selected.
8 EON indicator
Lights up when an RDS station that offers the EON data
service is being received.
9 STEREO indicator
Lights up when the unit is receiving a strong signal for an
FM stereo broadcast while the AUTO indicator is lit.
0 AUTO indicator
Shows that this unit is in the automatic tuning mode.
q VOLUME level indicator
Indicates the volume level.
w Input source indicator
Shows the current input source with the arrow-shaped
cursor.
e c indicator
Lights up when the built-in Dolby Digital Matrix 6.1 or
DTS ES decoder is on.
r v indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
t SP A/B indicator
Lights up according to which set of main speakers is
selected. Both indicators light up when both sets of
speakers are selected.
y Headphones indicator
Lights up when headphones are connected.
u Multi-information display
Shows the current DSP program name and other
information when adjusting or changing settings.
i MEMORY indicator
Flashes to show a station can be stored.
o Program type name indicators
The name of the selected program type lights up when the
EON indicator lights up.
p TUNED indicator
Lights up when this unit tunes in to a station.
a SLEEP indicator
Lights up while the sleep timer is on.
10
CONTROLS AND FUNCTIONS
(Europe model)
Rear Panel
1 DIGITAL INPUT jacks
2 DIGITAL OUTPUT jacks
3 Antenna input terminals
See page 30 for connection information.
4 Audio component jacks
See pages 12 and 13 for connection information.
5 Video component jacks
See pages 14 and 15 for connection information.
6 Speaker terminals
See pages 16 and 17 for connection information.
7 OUTPUT jacks
See page 18 for connection information.
8 AC power cord
Connect to a power outlet.
9 AC OUTLET(S)
Use these outlets to supply power to your other A/V
components (see page 19).
0 6CH INPUT jacks
See pages 13 and 18 for connection information.
q IMPEDANCE SELECTOR switch
Use this switch to match the amplifier output to your
speaker impedance. Set this unit in the standby mode
before you change the setting of this switch (see page 19).
DIGITAL OUTPUT AUDIO AUDIO VIDEO
SPEAKERS OUTPUT
MAIN
CENTER
REAR
(SURROUND)
TUNER
DIGITAL INPUT 6CH INPUT
MD/
TAP E
CD-R
CD-R
CD
DVD
FM
ANT
AM
ANT
GND
GND
75
UNBAL.
D-TV
/LD
OPTICAL
OPTICAL
COAXIAL
CD
IN
(PLAY)
DVD
S VIDEO VIDEO COMPONENT
DVD
Y
P
B
/
C
B
P
R
/
C
R
S VIDEO VIDEO
D-TV
/LD
CBL
/SAT
IN
VCR 1
OUT
IN
VCR 2
/DVR
OUT
MONITOR
OUT
R
MD/TAPE
CBL
/SAT
OUT
(REC)
CD
PHONO
MAIN
CENTER
SUB
WOOFER
SURROUND
IN
(PLAY)
CD-R
OUT
(REC)
L R L
MAIN
CENTER
SUB
WOOFER
R L
LR
R
+
L
R L
D-TV/LD
A
Y
P
B
/
C
B
P
R
/
C
R
MONITOR
OUT
Y
P
B
/
C
B
P
R
/
C
R
+
+
+
+
B
REAR
(SURROUND)
MAIN A OR B: 4
MIN. /SPEAKER
A
+
B: 8
MIN. /SPEAKER
CENTER
: 6
MIN. /SPEAKER
REAR
: 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A
+
B:
16
MIN. /SPEAKER
CENTER
: 8
MIN. /SPEAKER
REAR
: 8
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SWITCHED
100W MAX. TOTAL
AC OUTLETS
MAINS
876
5
4
32
1
9
0
q
As this terminal is used
for an examination in the
factory, do not connect
any equipment to this
terminal.
11
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
Speakers to Be Used
This unit has been designed to provide the best sound-
field quality with a 5-speaker system, using left and right
main speakers, left and right rear speakers, and a center
speaker. If you use different brands of speakers (with
different tonal qualities) in your system, the tone of a
moving human voice and other types of sound may not
shift smoothly. We recommend that you use speakers
from the same manufacturer or speakers with the same
tonal quality.
The main speakers are used for the main source sound
plus the effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for the effect and surround sounds, and the center
speaker is for the center sounds (dialog, vocals, etc.). If
for some reason it is not practical to use a center speaker,
you can do without it. Best results, however, are obtained
with the full system.
The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers. For
precise sound localization, however, it is ideal to use
high-performance models that can reproduce sounds over
the full range for the center speaker and the rear speakers.
Use of a subwoofer expands your
sound field
It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
the Dolby Digital signal or the DTS signal is played back.
The YAMAHA Active Servo Processing Subwoofer
System is ideal for natural and lively bass reproduction.
Speaker Placement
Refer to the following diagram when you place the
speakers.
Main
speaker (L)
Center speaker
Main speaker (R)
Rear speaker (R)
Rear speaker (L)
1.8 m
Main speakers
Place the left and right main speakers an equal distance
from the ideal listening position. The distance of each
speaker from each side of the video monitor should be the
same.
Rear speakers
Place these speakers behind your listening position,
facing slightly inwards, nearly 1.8 m (approx. 6 feet)
above the floor.
Center speaker
Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible, such as directly over or under the
monitor and centrally between the main speakers.
Note
If the center speaker is not used, the center channel sound will
be heard from the left and right main speakers. In this case,
1A CENTER SP on the SET MENU is set to NONE (see
page 41 for details).
Subwoofer
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the main speakers. Turn it
slightly toward the center of the room to reduce the wall
reflections.
CAUTION
Some types of speakers interfere with a video monitor.
If this problem occurs, move the speakers away from
the monitor. If you cannot avoid installing the center
speaker or subwoofer near the video monitor, use a
magnetically shielded speaker.
PREPARATION
Subwoofer
12
CONNECTIONS
Before Connecting Components
CAUTION
Never connect this unit and other components to mains power until all connections between components have been
completed.
Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, + to + and “–” to “–”. Some
components require different connection methods and have different jack names. Refer to the operation instructions
for each component to be connected to this unit.
When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or
changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling
system to all its products.
After you have completed all connections, check them again to make sure they are correct.
Connecting Audio Components
Connecting to digital jacks
This unit has digital jacks for direct transmission of
digital signals through either coaxial or fiber optic cables.
You can use the digital jacks to input PCM, Dolby Digital
and DTS bitstreams. When you connect components to
both the COAXIAL and OPTICAL jacks, priority is given
to the input signals from the COAXIAL jack. All digital
input jacks are acceptable for 96-kHz sampling digital
signals (see page 25 for details).
y
You can designate the input for each digital jack according to
your component by using 7 I/O ASSIGNMENT on the SET
MENU (see page 44 for details).
About the dust protection cap
Pull out the cap from the optical jack
before you connect the fiber optic cable.
Do not discard the cap. When you are not
using the optical jack, be sure to put the
cap back in place. This cap protects the
jack from dust.
Note
The OPTICAL jacks on this unit conform to the EIA standard.
If you use a fiber optic cable that does not conform to this
standard, this unit may not function properly.
Connecting a turntable
PHONO jacks are for connecting a turntable with an MM
or high-output MC cartridge. If you have a turntable with
a low-output MC cartridge, use an inline boosting
transformer or MC-head amplifier when connecting to
these jacks.
y
The GND terminal does not electrically ground the turntable. It
simply reduces noise in the signal. In some cases, you may
hear less noise if you do not connect to the GND terminal.
Connecting a CD player
y
The COAXIAL CD and OPTICAL CD jacks are available for a
CD player which has coaxial or optical digital output jacks.
When you connect a CD player to both the COAXIAL CD and
OPTICAL CD jacks, priority is given to the input signals from
the COAXIAL CD jack.
Connecting an MD recorder, tape
deck or CD recorder
y
Only digital signals input from a source such as a CD or DVD
are output from the DIGITAL OUTPUT jacks.
When you connect your recording component to both the
analog and digital input and output jacks, the priority is given
to the digital signal.
You can connect an MD recorder to any digital input jack by
using 7 I/O ASSIGNMENT on the SET MENU (see
page 44).
Notes
When you connect a recording component to this unit, keep its
power on while using this unit. If the power is off, this unit may
distort the sound from other components.
When you record from a source component connected to this
unit while this unit is set in the standby mode, the recorded
sound may be distorted. To avoid this problem, turn on this
unit.
13
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
DIGITAL OUTPUT AUDIO AUDIO VIDEO
TUNER
DIGITAL INPUT 6CH INPUT
MD/
TAPE
CD-R
CD-R
CD
DVD
FM
ANT
AM
ANT
GND
GND
75
UNBAL.
D-TV
/LD
OPTICAL
OPTICAL
COAXIAL
CD
IN
(PLAY)
DVD
S VIDEO VIDEO COMPONENT
DVD
Y
P
B/
C
B
PR/
C
R
S VIDEO VIDEO
D-TV
/LD
CBL
/SAT
IN
VCR 1
OUT
IN
VCR 2
/DVR
OUT
MONITOR
OUT
R
MD/TAPE
CBL
/SAT
OUT
(REC)
CD
PHONO
MAIN
CENTER
SUB
WOOFER
SURROUND
IN
(PLAY)
CD-R
OUT
(REC)
L R L
D-TV/LD
Y
P
B/
C
B
PR/
C
R
MONITOR
OUT
Y
P
B/
C
B
PR/
C
R
L
R
L
R
O
O
O
OUTPUT
GND
L
R
L R
L R
INPUT OUTPUT INPUTOUTPUT
OUTPUT
O
C
COAXIAL
OUTPUT
L
R
L
R
OPTICAL
OUTPUT
OPTICAL
INPUT
OPTICAL
INPUT
OPTICAL
OUTPUT
SUBWOOFER
OUTPUT
CENTER OUTPUT
MAIN
OUTPUT
SURROUND
OUTPUT
L R
L
R
C
O
MD recorder or
tape deck
indicates signal direction
indicates coaxial cables
CD recorder
CD player
Turntable
External decoder
See page 18.
indicates left analog cables
indicates right analog cables
indicates optical cables
(Europe model)
14
CONNECTIONS
Y
P
B/
C
B
PR/
C
R
Connecting Video Components
About the video jacks
There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composit video
signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.
The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO
jacks are separated into luminance (Y) and color difference (P
B
/C
B
, P
R
/C
R
) video signals. The jacks are also separated
into three for each signal. The description of the component video jacks may be different depending on the component
(e.g. Y, C
B
, C
R
/Y, P
B
, P
R
/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.
If your video component has an S-video output or component video output, you can connect it to this unit. Connect the
S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks
on your video component to the COMPONENT VIDEO jacks.
VIDEO jack
(composite)
S VIDEO jack COMPONENT VIDEO
jacks
y
Each type of video jack works independently. Signals input
through the composite video, S-video and component jacks are
output through the corresponding composite video, S-video,
and component jacks, respectively.
If you make S-video connections to this unit, it is not necessary
to make composite video connections. If both types of
connections are made, this unit gives priority to the S-video
signal.
You can designate the input for the COMPONENT VIDEO A
and B jacks according to your component by using 7 I/O
ASSIGNMENT on the SET MENU (see page 44 for details).
Notes
Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when
connecting to the COMPONENT VIDEO jacks.
When you are using the COMPONENT VIDEO jacks, check the details in the owners manual that came with the component being
connected.
Video monitor with a 21-pin connector
Make a connection as shown on page 15 with a commercially available SCART-plug connector cable.
VIDEO AUX jacks (on the front panel)
These jacks are used to connect any video input source
such as a game console to this unit.
S VIDEO VIDEO
L AUDIO R OPTICAL
VIDEO AUX
AUDIO OUT R
AUDIO OUT L
VIDEO OUT
OPTICAL OUT
S VIDEO OUT
O
V
L
R
S
Game console
15
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
DIGITAL OUTPUT AUDIO AUDIO VIDEO
TUNER
DIGITAL INPUT 6CH INPUT
MD/
TAPE
CD-R
CD-R
CD
DVD
FM
ANT
AM
ANT
GND
GND
75
UNBAL.
D-TV
/LD
OPTICAL
OPTICAL
COAXIAL
CD
IN
(PLAY)
DVD
S VIDEO VIDEO COMPONENT
DVD
Y
P
B
/
C
B
P
R
/
C
R
S VIDEO VIDEO
D-TV
/LD
CBL
/SAT
IN
VCR 1
OUT
IN
VCR 2
/DVR
OUT
MONITOR
OUT
R
MD/TAPE
CBL
/SAT
OUT
(REC)
CD
PHONO
MAIN
CENTER
SUB
WOOFER
SURROUND
IN
(PLAY)
CD-R
OUT
(REC)
L R L
D-TV/LD
Y
P
B
/
C
B
P
R
/
C
R
MONITOR
OUT
Y
P
B
/
C
B
P
R
/
C
R
L
R
S VIDEO
OUTPUT
S VIDEO
OUTPUT
S VIDEO
OUTPUT
S VIDEO
INPUT
VIDEO
INPUT
S VIDEO
OUTPUT
*1
AUDIO
OUTPUT
AUDIO
OUTPUT
AUDIO INPUT
AUDIO OUTPUT
COAXIAL
OUTPUT
OPTICAL
OUTPUT
RF
OUTPUT
OPTICAL
OUTPUT
VIDEO
OUTPUT
VIDEO
OUTPUT
AUDIO
OUTPUT
VIDEO
OUTPUT
S VIDEO
INPUT
VIDEO
OUTPUT
VIDEO
INPUT
RF
INPUT
O
V
S
O
L
R
L
R
L
R
V
S
COMPONENT
INPUT
COMPONENT
OUTPUT
COMPONENT
OUTPUT
V
S
V
V
S S
L
R
C
C
V
S
L
R
V
L
S
R
V
C
O
Note
If your LD player has an Dolby Digital RF signal output jack, connect it to this unit
through an RF demodulator (separately purchased).
indicates signal direction
indicates left analog cables
indicates right analog cables
indicates S-video cables
TV/digital TV or
LD player
DVD player
Cable TV or
Satellite tuner
VCR 1 or VCR 2/
DVR (digital
video recorder)
Video monitor
indicates coaxial cables
indicates optical cables
indicates video cables
(Europe model)
LD player
No connection
SCART-plug
*1 You can connect the Dolby
Digital RF signal output of
your LD player to the
COAXIAL jack by using
7 I/O ASSIGNMENT on
the SET MENU (see
page 44).
RF
demodulator
16
CONNECTIONS
Connecting the Speakers
Be sure to connect the left channel (L), right channel (R), + (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
Use speakers with the specified impedance shown on the rear panel of this unit.
Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could
damage the unit and/or speakers.
If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.
Speaker cables
A speaker cord is actually a pair of insulated cables
running side by side. One of the cables is colored or
shaped differently, perhaps with a stripe, groove or ridge.
1 Remove approx. 10 mm (3/8) of insulation
from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
12
Connecting to the SPEAKERS terminals
1 Unscrew the knob.
2 Insert one bare wire into the hole in the side
of each terminal.
3 Tighten the knob to secure the wire.
2
1
3
Red: positive (+)
Black: negative ()
MAIN SPEAKERS terminals
One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either
of the MAIN A or B terminals.
REAR SPEAKERS terminals
A rear speaker system can be connected to these terminals.
CENTER SPEAKER terminals
A center speaker can be connected to these terminals.
10 mm (3/8)
17
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
SPEAKERS OUTPUT
MAIN
CENTER
REAR
(SURROUND)
MAIN
CENTER
SUB
WOOFER
R L
LR
R
+
L
R L
A
+
+
+
+
B
REAR
(SURROUND)
MAIN A OR B: 4
MIN. /SPEAKER
A
+
B: 8
MIN. /SPEAKER
CENTER
: 6
MIN. /SPEAKER
REAR
: 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A
+
B:
16
MIN. /SPEAKER
CENTER
: 8
MIN. /SPEAKER
REAR
: 8
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SWITCHED
100W MAX. TOTAL
AC OUTLETS
MAINS
Main speakers A
Right Left
Main speakers B
Right Left
(Europe model)
Center speaker Rear speakers
Right Left
Subwoofer
system
Subwoofer connection
See SUBWOOFER jack on page 18.
18
CONNECTIONS
Connecting to an External
Amplifier
If you want to increase the power output to the speakers,
or want to use another amplifier, connect an external
amplifier to the OUTPUT jacks as follows.
Note
When RCA pin plugs are connected to the OUTPUT jacks for
output to an external amplifier, it is not necessary to use the
corresponding SPEAKERS terminals.
1 MAIN jacks
Main channel line output jacks.
Note
The signals output through these jacks are affected by the
BASS, TREBLE and BASS EXTENSION settings.
2 SUBWOOFER jack
When using a subwoofer with built-in amplifier, including
the YAMAHA Active Servo Processing Subwoofer
System, connect the input jack of the subwoofer system
to this jack. Low bass signals distributed from the main,
center and/or rear channels are directed to this jack. (The
cut-off frequency of this jack is 90 Hz.) The LFE (low-
frequency effect) signals generated when Dolby Digital or
DTS is decoded are also directed if they are assigned to
this jack.
Notes
Adjust the volume level of the subwoofer with the control on
the subwoofer. The subwoofer volume cannot be adjusted from
this unit.
Depending on the settings of 1 SPEAKER SET, 10A LFE
LEVEL and 11 DTS LFE LEVEL on the SET MENU,
some signals may not be output from the SUBWOOFER jack.
3 CENTER jack
Center channel line output jack.
4 REAR (SURROUND) jacks
Rear channel line output jacks.
OUTPUT
MAIN
CENTER
SUB
WOOFER
R L
LR
REAR
(SURROUND)
1
2
3
4
Connecting an External Decoder
This unit is equipped with 6 additional input jacks (left
and right MAIN, CENTER, left and right SURROUND
and SUBWOOFER) for discrete multi-channel input from
an external decoder, sound processor or pre-amplifier.
Connect the output jacks on your external decoder to the
6CH INPUT jacks. Be sure to match the left and right
outputs to the left and right input jacks for the main and
surround channels.
Notes
When you select 6CH INPUT as the input source, this unit
automatically turns off the digital sound field processor, and
you cannot listen to DSP programs.
When you select 6CH INPUT as the input source, changing
items 1A to 1E on the SET MENU is not affected.
19
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
MAIN A OR B: 4
MIN. /SPEAKER
A
+
B: 8
MIN. /SPEAKER
CENTER
: 6
MIN. /SPEAKER
REAR
: 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A
+
B:
16
MIN. /SPEAKER
CENTER
: 8
MIN. /SPEAKER
REAR
: 8
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SWITCHED
100W MAX. TOTAL
AC OUTLETS
MAINS
IMPEDANCE SELECTOR Switch
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or POWER) is pressed, the IMPEDANCE SELECTOR switch may
not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the standby
mode.
Select the left or right position according to the impedance of the speakers in your system. Be sure to move this switch
only when this unit is in the standby mode.
Switch
position
Speaker Impedance level
Main
If you use one set of main speakers, the impedance of
each speaker must be 4 or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 8 or higher.
Center
The impedance must be 6 or higher.
Rear
The impedance of each speaker must be 6 or higher.
Right
Main
If you use one set of main speakers, the impedance of
each speaker must be 8 or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 16 or higher.
Center
The impedance must be 8 or higher.
Rear
The impedance of each speaker must be 8 or higher.
Left
Connecting the Power Supply Cords
After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if
you will not use this unit for a long period of time.
AC OUTLET(S) (SWITCHED)
Europe model ............................................... 2 OUTLETS
U.K. model ..................................................... 1 OUTLET
Use these outlets to connect the power cords from your
components to this unit. The power to the AC
OUTLET(S) is controlled by this units STANDBY/ON
(or POWER and STANDBY). These outlets will supply
power to any connected component whenever this unit is
turned on. The maximum power (total power
consumption of components) that can be connected to the
AC OUTLET(S) is 100 W.
MAIN A OR B: 4
MIN. /SPEAKER
A
+
B: 8
MIN. /SPEAKER
CENTER
: 6
MIN. /SPEAKER
REAR
: 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A
+
B:
16
MIN. /SPEAKER
CENTER
: 8
MIN. /SPEAKER
REAR
: 8
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SWITCHED
100W MAX. TOTAL
AC OUTLETS
MAINS
SWITCHED
(Europe model)
(Europe model)
IMPEDANCE SELECTOR
To AC outlet
20
ON-SCREEN DISPLAY (OSD)
Full display Short display
You can display the operation information for this unit on
a video monitor. If you display the SET MENU and DSP
program parameter settings on a monitor, it is much easier
to see the available options and parameters than it is by
reading this information on the front panel display.
y
If a video source is being reproduced, the OSD is
superimposed over the image.
The OSD signal is not output to the REC OUT jack, and will
not be recorded with any video signal.
You can set the OSD to turn on (blue background) or off when
a video source is not being reproduced (or the source
component is turned off) by using 14 DISPLAY SET on the
SET MENU (see page 46).
OSD Modes
You can change the amount of information the OSD
shows.
Full display
This mode always shows the DSP program parameter
settings on the video monitor (see page 63).
Short display
This mode briefly shows the same contents as the front
panel display at the bottom of the screen and then
disappears.
Display off
This mode briefly shows the DISPLAY OFF message at
the bottom of the screen and then disappears. Afterwards,
no changes to operations appear on the monitor except
those of the ON SCREEN button.
P01 CONCERT HALL
INIT. DLY
45ms
ROOM SIZE 1.0
LIVENESS
5
P01 CONCERT HALL
y
When you choose the full display mode, INPUT l / h,
VOLUME and some other types of operation information are
displayed at the bottom of the screen in the same format as that
for the front panel display.
The SET MENU and test tone display appear regardless of the
OSD mode.
Selecting the OSD Mode
1 When you turn on the power, the video
monitor and front panel display show the
level of the main volume for a few seconds
and then switch to show the current DSP
program.
2 Press ON SCREEN on the remote control
repeatedly to change the display mode.
The OSD mode changes in the following order: full
display, short display, and display off.
Notes
If you choose a video input source that has a component
connected to both the S VIDEO IN and composite VIDEO IN
jacks, and both the S VIDEO OUT and composite VIDEO
OUT jacks are connected to a video monitor, the video signal is
output to both the S VIDEO OUT and VIDEO OUT jacks.
However, the OSD is carried only on the S-video signal. If no
video signal is input, the OSD is carried on both the S-video
and composite video signals.
If your video monitor is connected only to the COMPONENT
VIDEO jacks of this unit, the OSD is not shown. Make sure to
connect your video monitor to the COMPONENT VIDEO
jacks and either VIDEO or S VIDEO jacks if you want to see
the OSD.
Playing back video software that has an anti-copy signal or
video signals with a lot of noise may produce unstable images.
21
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER MODE SETTINGS
This unit has 5 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your
configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings
as well as other possible settings. If the initial settings are not appropriate for your speaker configuration, change the
settings on the SET MENU (see page 39).
Summary of SPEAKER SET Items 1A through 1E
Item Description Initial setting
1A CENTER SP Selects the center channel output mode according to the size of the center speaker.
The possible settings are LRG (large), SML (small) and NONE.
LRG
1B MAIN SP Selects the main channel output mode according to the size of the main speakers.
The possible settings are LARGE and SMALL.
LARGE
1C REAR L/R SP Selects the rear channel output mode according to the size of the rear speakers.
The possible settings are LRG (large), SML (small) and NONE.
LRG
1D LFE/BASS OUT Selects a speaker for the LFE signal output and low bass signal.
The possible settings are SWFR (subwoofer), MAIN, and BOTH.
BOTH
1E MAIN LEVEL Selects the output level for the main channel signal.
The possible settings are Normal and 10 dB.
Normal
22
ADJUSTING THE SPEAKER OUTPUT LEVELS
This section explains how to adjust the speaker output
levels by using the test tone generator. When this
adjustment is made, the output level heard at the listening
position will be the same from each speaker. This is
important for the best performance of the digital sound
field processor, the Dolby Pro Logic decoder, Dolby
Digital decoder and DTS decoder.
Note
Since this unit cannot enter the test mode while headphones are
connected to this unit, be sure to unplug the headphones from
the PHONES jack when using the test tone.
Before You Begin
1 Press STANDBY/ON to
turn on the power. Turn on
the video monitor.
2 Press SPEAKERS A or B
to select the main
speakers to be used.
If you are using two sets of the
main speakers, press both A
and B.
3 Set BASS and TREBLE on the front panel to
the center position and set BASS
EXTENSION to OFF.
Using the Test Tone (TEST DOLBY
SUR.)
Use the test tone to balance the output levels of the 5
speakers required for a surround sound system. The
adjustment of each speaker output level should be made at
your listening position with the remote control. After
completing the adjustments, use VOLUME +/ at your
listening position to check if the adjustments are
satisfactory.
1 Set the selector dial to the
AMP/TUN (or DSP/TUN)
position.
2 Press TEST to output the test tone.
3 Adjust the volume so you can hear the test
tone.
The test tone is heard from the left main speaker,
center speaker, right main speaker, right rear speaker
and left rear speaker in order. The tone is produced
for 2.5 seconds each time.
BASS
+
TREBLE
+
LEFT SURROUND
(TEST L SUR.)
RIGHT SURROUND
(TEST R SUR.)
CENTER
(TEST CENTER)
RIGHT
(TEST RIGHT)
LEFT
(TEST LEFT)
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
1
2
33
2,6
5
4
1
3
BASS
EXTENSION
PROCESSOR
DIRECT
ON OFF
Set to OFF.
STANDBY
/ON
SPEAKERS
AB
23
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONSADJUSTING THE SPEAKER OUTPUT LEVELS
The state of the test tone output is also shown on the
monitor by an image of the audio listening room.
This is convenient for adjusting each speaker level.
y
If 1A CENTER SP on the SET MENU is set to NONE, the
center channel sound is automatically output from the left and
right main speakers.
Note
If the test tone cannot be heard, turn down the volume, set the
unit in the standby mode and check the speaker connections.
4 Press LEVEL repeatedly
to select the speaker to be
adjusted.
y
Once you press LEVEL, you can also select the speaker to be
adjusted by pressing d. (Pressing u changes the selection in
the reverse order.)
5 Press j / i repeatedly to
adjust the output level of
the effect speakers so that
the output level coming
from each speaker is the
same.
While adjusting, the test tone is heard from the
selected speaker.
6 When the adjustment is complete, press
TEST.
The test tone stops and the
current DSP program appears
on the front panel display and
on the video monitor.
y
The tonal quality of the center speaker can be adjusted by using
5 CENTER GEQ on the SET MENU (see page 43).
You can increase the output levels of the effect speakers
(center, left rear and right rear) to +10 dB. If the output level of
these speakers is lower than that of the main speakers even
after you have increased the output level of these speakers up to
+10 dB, set 1E MAIN LEVEL on the SET MENU to 10 dB
(see page 42). This setting decreases the main speaker output
level to about one-third of the normal level. After you have set
1E MAIN LEVEL on the SET MENU to 10 dB, adjust the
levels for the center and rear speakers again.
TEST DOLBY SUR.
LEFT
24
BASIC PLAYBACK
3 Press INPUT l / h repeatedly (or press one
of the input selector buttons) to select the
input source.
The current input source is indicated on the front
panel display with an arrow.
The current input source name and input mode
appear on the front panel display and on the video
monitor for a few seconds.
Front panel
or
Remote control
Selected input source
BASIC OPERATION
When using the remote control, set the selector dial to
the AMP/TUN position.
2 Press SPEAKERS A or B
to select the main
speakers to be used.
If you are using two sets of
main speakers, press both A
and B.
1 Press STANDBY/ON (or POWER) to turn on
the power. Turn on the video monitor.
The front panel display and the video monitor show
the level of the main volume for a few seconds and
then switch to show the current DSP program.
Select this: To reproduce the signal from
this component
DVD: DVD player
D-TV/LD: TV or digital TV/LD player
CBL/SAT: Cable TV/satellite tuner
VCR 1: Video cassette deck 1
VCR 2/DVR: Video cassette deck 2/digital
video recorder
V-AUX: Another A/V component
(connected to the VIDEO AUX
jacks on the front panel)
PHONO: Turntable
CD: CD player
TUNER: AM/FM tuner
CD-R: CD recorder
MD/TAPE: MD recorder/tape deck
INPUT
1
5
6
3
DIGITAL
DIGITAL
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAINMENT
PRO
LOGIC
ENTERTAINMENT
DSP
DSP
6.1/ES
PCM
PRO LOGIC
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
VIRTUAL
PS
PS
PTY
PTY
RT
RT
CT
CT
PTY
PTY
HOLD
HOLD
EON
EON
STEREO
STEREO
AUTO
AUTO
NEWS INFO AFFAIRS SPORT
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
MEMORY TUNED
ZONE 2
ZONE 2
VOLUME
dB
dB
ms
ms
SLEEP
SLEEP
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
1
5
353
25
6
Front panel
Remote controlFront panel
or
STANDBY
/ON
SPEAKERS
AB
25
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
BASIC PLAYBACK
6CH INPUT
PROGRAM
DIGITAL
DTS MOVIE THEATER 1
2
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
DSP
6.1/ES
PCM
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
VOLUME
dB
ms
SLEEP
To select a source connected to the 6CH INPUT
jacks
Press 6CH INPUT until 6CH INPUT appears on the
front panel display and on the video monitor.
Front panel
or
Remote control
Notes
If 6CH INPUT is shown on the front panel display and on
the video monitor, no other source can be played. To select
another input source with INPUT l / h (or the input selector
buttons), press 6CH INPUT to turn off 6CH INPUT from the
front panel display and the video monitor.
If you want to enjoy an audio source connected to the 6CH
INPUT jacks together with a video source, first select the video
source and then press 6CH INPUT.
4 Start playback (or select a broadcast station)
on the source component.
Refer to the operation instructions for the
component.
5 Adjust the volume to the desired output
level.
If desired, use BASS, TREBLE and BASS
EXTENSION etc. These controls are only effective
for sound from the main speakers.
or
Front panel
Note
If the component connected to the VCR 1 OUT, VCR 2/DVR
OUT, CD-R OUT and MD/TAPE OUT jacks is turned off, the
reproduced sound may be distorted or the volume may be
lowered. In these cases, turn on the component.
6 Use the digital sound field processor.
See page 28.
Front panel
or
Remote control
To mute the sound
Press MUTE on the
remote control.
To restore the audio output to
the previous volume level,
press MUTE again.
y
You can also cancel mute to press any operation buttons such as
VOLUME +/.
During muting, MUTE ON appears on the front panel
display and on the video monitor.
When you have finished using
this unit
Press STANDBY/ON (or STANDBY) to set
this unit in the standby mode.
Notes on the digital signal
The digital input jacks of this unit can also handle
96-kHz sampling digital signals. (To utilize this, use a
source that supports 96-kHz sampling digital signals and
set the player for digital output. Refer to the operation
instructions for the player.) Note the following when a 96-
kHz sampling digital signal is input to this unit:
1. The following indication will appear on the front panel
display.
2. DSP programs cannot be selected. Sound will be
output as normal 2-channel stereo sound from only the
left and right main speakers.
Note
If 1B MAIN SP on the SET MENU is set to SMALL or 1D
LFE/BASS OUT is set to BOTH, the sound is also output
from the subwoofer.
3. Adjustment of the speaker output level described on
page 47 cannot be made.
VOLUME
BASS
+
TREBLE
+
BASS
EXTENSION
PROCESSOR
DIRECT
ON OFF
Front panel Remote control
26
BASIC PLAYBACK
INPUT MODE
BGV (background video) function
The BGV function allows you to combine a video image
from a video source with a sound from an audio source.
(For example, you can listen to classical music while you
are watching a video.)
Select a source from the video group and then select a
source from the audio group with the input selector
buttons on the remote control. The BGV function does
not work if you select the sources with INPUT l / h on
the front panel.
Input Modes and Indications
This unit comes with various input jacks. If your
component is connected to more than one type of input
jack, you can set the priority of the input signal.
When you turn on the power of this unit, the input mode
is set according to 8 INPUT MODE on the SET MENU
(see page 44 for details).
Press INPUT MODE (or the input selector
button that you have pressed to select the
input source on the remote control)
repeatedly until the desired input mode is
shown on the front panel display and on the
video monitor.
Front panel
or
Remote control
Input mode
AUTO: In this mode, the input signal is
automatically selected in the following
order:
1) Dolby Digital or DTS signal
2) Digital (PCM) signal
3) Analog signal
DTS: In this mode, only the digital input signal
encoded with DTS is selected even if
another signal is input at the same time.
ANALOG: In this mode, only the analog input signal is
selected even if a digital signal is input at
the same time.
Notes
If digital signals are input from both the COAXIAL and
OPTICAL jacks, the digital signal from the COAXIAL jack is
selected.
When AUTO is selected, this unit automatically determines the
type of signal. If this unit detects a Dolby Digital or DTS
signal, the decoder automatically switches to the appropriate
setting and reproduces 5.1 channel source.
The sound output may be interrupted for some LD and DVD
players in the following situation: The input mode is set to
AUTO. A search is performed while playing the disc encoded
with Dolby Digital or DTS, and then disc playing is restored.
The sound output is interrupted for a moment because the
digital signal was selected again.
DIGITAL
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAINMENT
PRO
LOGIC
ENTERTAINMENT
DSP
6.1/ES
PCM
PRO LOGIC
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
VIRTUAL
PS
PS
PTY
PTY
RT
RT
CT
CT
PTY
PTY
HOLD
HOLD
EON
EON
STEREO
STEREO
AUTO
AUTO
NEWS INFO AFFAIRS SPORT
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
MEMORY TUNED
ZONE 2
ZONE 2
VOLUME
dB
dB
ms
ms
SLEEP
SLEEP
27
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
BASIC PLAYBACK
Notes on playing a source
encoded with a DTS signal
If the digital output data of the player has been
processed in any way, you may not be able to
perform DTS decoding even if you make a digital
connection between this unit and the player.
If you play a source encoded with a DTS signal and
set the input mode to ANALOG, this unit reproduces
the noise of an unprocessed DTS signal. When you
want to play a DTS source, be sure to connect the
source to a digital input jack and set the input mode
to AUTO or DTS.
If you switch the input mode to ANALOG while
playing a source encoded with a DTS signal, this unit
reproduces no sound.
If you play a source encoded with a DTS signal and
set the input mode to AUTO, there will be a moment
of noise while the unit recognizes the DTS signal and
turns on the DTS decoder. This is not a malfunction.
You can avoid this by setting the input mode to DTS
beforehand.
If you continue to play a source encoded with a DTS
signal with the input mode setting left to AUTO, this
unit automatically switches to the DTS-decoding
mode to prevent noise from being generated during
subsequent operation. (The t indicator lights
up on the front panel display.) The t indicator
will flash immediately after playback of a source
encoded with a DTS signal has finished. Only a
source encoded with a DTS signal can be played
back while this indicator is flashing. If you want to
play a normal PCM source soon, set the input mode
back to AUTO.
The t indicator will flash when the input mode
is set to AUTO and a search or skip operation is
performed while playing back a source encoded with
a DTS signal. If this status continues for 30 or more
seconds, the unit will automatically switch from the
DTS-decoding mode to PCM digital signal input
mode and the t indicator will go out.
Notes on playing an LD source
For LD software that does not contain a digital
soundtrack, connect the LD player to the analog jacks
and set the input mode to AUTO or ANALOG.
If the LD player is transmitting a signal by a non-
standard method, this unit cannot detect the Dolby
Digital or DTS signal. In this case, the decoder
automatically switches to PCM or analog.
Some A/V components such as LD players output
different audio signals through their analog and digital
jacks. Change the input mode as necessary.
While you are operating the LD player and playing a
disc encoded with a Dolby Digital signal, if you
switch from the pause or chapter forwarding function
to normal playback, you may hear the PCM or analog
sound an instant before the Dolby Digital signal is
played.
28
BASIC PLAYBACK
DIGITAL
DTS MOVIE THEATER 1
2
DSP
6.1/ES
PCM
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
VOLUME
dB
ms
SLEEP
Selecting a Sound Field Program
You can enhance your listening experience by selecting a
DSP program. For details about each program, see pages
57 to 60.
1 Press DSP on the remote
control.
The indicator lights up for
about 3 seconds.
Remote control
y
If the selector dial is set to the DSP/TUN position, skip this
step.
2 Use the numeric buttons to select the
desired program before the indicator goes
off (or press PROGRAM l / h repeatedly on
the front panel).
For example, to select the sub-program
Spectacle, press MOVIE THEATER 1
repeatedly.
The name of the selected program appears on the
front panel display and on the video monitor.
PROGRAM
Front panel
or
Remote control
Program group
Program name (sub-program)
Notes
Choose a DSP program based on your listening preference, and
not on the name of the program. The acoustics of your listening
room affect the DSP program. Minimize the sound reflections
in your room to maximize the effect created by the program.
When you select an input source, this unit automatically selects
the last DSP program used with that source.
When you set this unit in the standby mode, the current source
and DSP program are memorized and are automatically
selected when you turn on the power again.
If a Dolby Digital or DTS signal is input when the input mode
is set to AUTO, the DSP program automatically switches to the
appropriate decoding program.
When a monaural source is being played with PRO LOGIC/
Normal or PRO LOGIC/ENHANCED, no sound will be heard
from the main speakers and the rear speakers. Sound can only
be heard from the center speaker. However, if 1A CENTER
SP on the SET MENU is set to NONE, the center channel
sound is output from the main speakers.
When a source connected to the 6CH INPUT jacks of this unit
is selected, the digital sound field processor cannot be used.
When 96-kHz sampling digital signals are input to this unit, the
DSP program cannot be selected. In this case, the sound is
reproduced as normal 2-channel stereo.
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
2
1
2
29
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
BASIC PLAYBACK
EFFECT
Dolby Digital Matrix 6.1 or DTS
ES decoder
If you want to use the Dolby Digital Surround EX or DTS
ES software, press 6.1/ES to turn on the Dolby Digital
Matrix 6.1 or DTS ES decoder (see 12 6.1/ES AUTO
on pages 45 and 60 for details).
Remote control
Virtual CINEMA DSP and SILENT
CINEMA DSP
You can experience the virtual CINEMA DSP sound field
by setting 1C REAR L/R SP on the SET MENU to
NONE. The sound field processing is changed to the
Virtual CINEMA DSP mode according to the selected
DSP program. Virtual CINEMA DSP is performed by
using the main speakers. You can also listen to SILENT
CINEMA DSP by connecting your headphones to the
PHONES jack while the digital sound field processor is
on.
Note
This unit is not set in the virtual CINEMA DSP mode even if
1C REAR L/R SP is set to NONE in the following cases:
when the 5ch Stereo, DOLBY DIGITAL/Normal or DTS/
Normal program is selected;
when the sound effect is turned off;
when 6CH INPUT is selected as the input source;
when 96-kHz sampling digital signals are input to this unit;
when the Dolby Digital KARAOKE source is played;
when using the test tone; or
when connecting the headphones.
Front panel
or
Remote control
y
If the selector dial is set to a position other than the DSP/TUN
position, first press DSP and then EFFECT on the remote
control.
Notes
If you turn off the sound effect, no sound is output from the
center and rear speakers.
If you turn off the sound effect while a Dolby Digital or DTS
signal is being output, the dynamic range of the signal is
automatically compressed and the sounds of the center and rear
speaker channels are mixed and output from the main speakers.
The volume may be greatly reduced when you turn off the
sound effect or if you set 10B D-RANGE on the SET MENU
to MIN. In this case turn on the sound effect.
Normal Stereo Reproduction
Press EFFECT to turn off the sound effect
for normal stereo reproduction.
Press EFFECT again to turn the sound effect back
on.
DIGITAL
DTS MOVIE THEATER 1
2
DSP
6.1/ES
PCM
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
VOLUME
SLEEP
The c indicator lights up.
30
TUNING
Connecting the Antennas
Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal
strength.
Connect each antenna correctly to the designated terminals.
Indoor FM
antenna
(included)
AM loop antenna
(included)
Ground (GND terminal)
For maximum safety and minimum
interference, connect the antenna GND
terminal to a good earth ground. A
good earth ground is a metal stake
driven into moist earth.
Connecting the indoor FM
antenna
Connect the included indoor FM antenna to the 75
UNBAL. FM ANT terminal.
Note
Do not connect an outdoor FM antenna and the indoor FM
antenna at the same time.
Connecting the AM loop antenna
1 Press and hold the tab to unlock the terminal
hole.
2 Insert the AM loop antenna lead wires into
the AM ANT and GND terminals.
DIGITAL OUTPUT
TUNER
DIGITAL INPUT
MD/
TAPE
CD-R
CD-R
CD
DVD
FM
ANT
AM
ANT
GND
GND
75
UNBAL.
D-TV
/LD
OPTICAL
OPTICAL
COAXIAL
CD
CBL
/SAT
5
4
Antenna stand
3 Release the tab to lock the lead wires.
Lightly pull the lead wires to confirm a good
connection.
4 Attach the loop antenna to the antenna
stand.
5 Orient the AM loop antenna so that the best
reception is obtained.
y
The AM loop antenna can be removed from the stand and
attached to a wall, etc.
Notes
The AM loop antenna should be placed away from this unit.
The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
A properly installed outdoor antenna provides clearer
reception than an indoor one. If you experience poor
reception quality, an outdoor antenna may improve the
quality. Consult the nearest authorized YAMAHA
dealer or service center about the outdoor antennas.
1
2
3
(Europe model)
Connecting a coaxial cable to the included
75-ohm/300-ohm antenna adapter (U.K. model
only)
11 (7/16)
8 (5/16)
6 (1/14)
12
3
54
Cover
Unit: mm
(inch)
Lead wire
Clamp with
pliers.
Clamp
with
pliers.
Insert the wire
into the slot.
Open the cover of the
included 75-ohm/300-ohm
antenna adapter.
Cut the external sleeve of
the 75-ohm coaxial cable
and prepare it for
connection.
Cut the lead wire and
remove it.
Insert the cable wire into the
slot, and clamp it with
pliers.
Snap the cover into
place.
31
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
TUNING
y
Use the manual tuning method if the tuning search does not
stop at the desired station because the signal is weak.
When tuned in to a station, the TUNED indicator lights up
and the frequency of the received station is shown on the front
panel display. If an RDS station that offers the PS data service
is being received, the station name is shown instead of the
frequency on the front panel display.
If the signal from the station you want to select is weak,
you must tune in to it manually.
3 Press TUNING MODE (AUTO/MANL MONO)
so that the AUTO indicator goes off from
the front panel display.
If the colon (:) appears on the front panel display
next to the band indication, press PRESET/TUNING
(EDIT) to turn it off.
3 Press TUNING MODE (AUTO/MANL MONO)
so that the AUTO indicator lights up on the
front panel display.
If the colon (:) appears on the front panel display
next to the band indication, press PRESET/TUNING
(EDIT) to turn it off.
4 Press PRESET/TUNING l / h to tune in to
the desired station manually.
Hold down the button to
continue the tuning search.
Note
Manually tuning in to an FM station will automatically change
the reception mode to monaural to increase the signal quality.
INPUT
4 Press PRESET/TUNING l or h once to
begin automatic tuning.
Press h to tune in to a higher
frequency, or press l to tune
in to a lower frequency. Press
the same button again if the
tuning search does not stop at
the desired station.
PRESET/
TUNING
TUNING
MODE
AUTO/MAN'L MONO
AUTO
Goes off
PRESET
/TUNING
EDIT
DIGITAL
DIGITAL
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAIN
MPRO
LOGIC
ENTERTAINMENT
DSP
DSP
6.1/ES
PCM
PRO LOGIC
PRO LOGIC
A
SP
B
VIRTUAL
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
dB
ms
SLEEP
Turn this indicator off.
PRESET/
TUNING
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
4
1
23
Automatic (or Manual) Tuning
Automatic tuning is effective when station signals are
strong and there is no interference.
1 Press INPUT l / h to
select TUNER as the input
source.
2 Press FM/AM to select the reception band.
FM or AM appears on the front panel display.
or
FM/AM
TUNING
MODE
AUTO/MAN'L MONO
AUTO
Lights up
PRESET
/TUNING
EDIT
DIGITAL
DIGITAL
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAIN
MPRO
LOGIC
ENTERTAINMENT
DSP
DSP
6.1/ES
PCM
PRO LOGIC
PRO LOGIC
A
SP
B
VIRTUAL
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
dB
ms
SLEEP
Turn this indicator off.
32
TUNING
3 Press and hold MEMORY (MANL/AUTO FM)
for more than 3 seconds.
The preset number, the MEMORY and AUTO
indicators flash. Then, after about 5 seconds,
automatic preset tuning begins from the frequency
currently displayed toward the higher frequencies.
When automatic preset tuning is completed, the front
panel display shows the frequency of the last preset
station.
TUNING
MODE
AUTO/MAN'L MONO
MEMORY
MAN'L/AUTO FM
AUTO
FM/AM
Presetting Stations
Automatically presetting stations
(for RDS stations)
You can use the automatic preset tuning feature to store
RDS stations. This function enables the unit to
automatically tune in to RDS stations with strong signals,
and to store up to 40 (8 stations x 5 groups) of those
stations in order. (See pages 35 to 37 for details on RDS
stations.) This feature enables you to easily tune in to any
preset station by selecting the preset station number (see
page 33).
1 Press FM/AM to select the FM band.
2 Press TUNING MODE (AUTO/MANL MONO)
so that the AUTO indicator lights up on the
front panel display.
Notes
Any stored station data existing under a preset number is
cleared when you store a new station under that preset
number.
You can manually replace a preset station with another FM or
AM station by simply following the procedure in the section
Manually presetting stations on page 33.
If the number of the received stations does not reach E8,
automatic preset tuning has automatically stopped after
searching all stations.
Only RDS stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength, tune in to it manually
in the monaural mode, and store it by following the procedure
in Manually presetting stations on page 33. (There may be
a case that this unit cannot receive a station which could be
received by using the automatic tuning method. This is
because this unit receives a large amount of PI (Program
Identification) data along with the station.)
Automatic preset tuning options
You can select the preset number from which the unit
will store RDS stations and/or begin tuning toward
lower frequencies. Before automatic preset tuning
begins (after pressing MEMORY in step 3):
1. Press A/B/C/D/E and PRESET/TUNING l / h to
select the preset number under which the first station
will be stored. Automatic preset tuning will stop
when stations have all been stored up to E8.
2. Press PRESET/TUNING (EDIT) to turn off the
colon (:) and then press PRESET/TUNING l to
begin tuning toward lower frequencies.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the preset stations may be cleared. If
so, store the stations again by using the presetting
station methods.
Lights up
DIGITAL
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAINMENT
PRO
LOGIC
ENTERTAINMENT
DSP
6.1/ES
PCM
PRO LOGIC
PRO LOGIC
A
SP
B
VIRTUAL
VIRTUAL
PS
PS
PTY
PTY
RT
RT
CT
CT
PTY
PTY
HOLD
HOLD
EON
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZO
ZONE 2
dB
ms
SL
ESLEEP
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
1
23
33
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
TUNING
Manually presetting stations
You can also store up to 40 stations (8 stations x 5
groups) manually.
1 Tune in to a station.
See page 31 for tuning instructions.
2 Press MEMORY (MANL/AUTO FM).
The MEMORY indicator flashes for about
5 seconds.
Flashes
3 Press A/B/C/D/E repeatedly to select a preset
station group (A to E) while the MEMORY
indicator is flashing.
The group letter appears and make sure that the
colon (:) appears on the front panel display next to
the band indication.
4 Press PRESET/TUNING l / h to select a
preset station number (1 to 8) while the
MEMORY indicator is flashing.
Press h to select a higher
preset station number. Press l
to select a lower preset station
number.
5 Press MEMORY (MANL/AUTO FM) while the
MEMORY indicator is flashing.
The station band and
frequency appear on the front
panel display with the preset
group and number you have
selected.
6 Repeat steps 1 to 5 to store other stations.
Notes
Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
The reception mode (stereo or monaural) is stored along with
the station frequency.
Tuning in to a Preset Station
You can tune any desired station simply by selecting the
preset station number under which it was stored.
You can also tune a preset station with the remote control.
Set the selector dial to the AMP/TUN position and press
TUNER to select TUNER as the input source.
MEMORY
MAN'L/AUTO FM
MEMORY
A/B/C/D/E
DIGITAL
DIGITAL
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAIN
MPRO
LOGIC
ENTERTAINMENT
DSP
DSP
6.1/ES
PCM
PRO LOGIC
PRO LOGIC
A
SP
B
VIRTUAL
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
dB
ms
SLEEP
PRESET/
TUNING
MEMORY
MAN'L/AUTO FM
DIGITAL
DIGITAL
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAINMENT
PRO
LOGIC
ENTERTAINMENT
DSP
DSP
6.1/ES
PCM
PRO LOGIC
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
VIRTUAL
PS
PS
PTY
PTY
RT
RT
CT
CT
PTY
PTY
HOLD
HOLD
EON
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
NEWS INFO AFFAIRS SPORT
MEMORY
MEMORY
TUNED
ZONE 2
ZONE 2
VOLUME
dB
dB
ms
ms
SLEEP
SLEEP
Shows the displayed station has been stored as A1.
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
4
2,5
3
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
1
2
2
1
34
TUNING
2 Press PRESET/TUNING l / h (or
PRESET /+) to select a preset station
number (1 to 8).
The preset group and number appear on the front
panel display along with the station band, frequency
and the TUNED indicator lights up.
Front panel
or
Remote control
Exchanging Preset Stations
You can exchange the assignment of two preset stations
with each other. The example below describes the
procedure for exchanging preset station E1 with A5.
1 Tune in to preset station E1.
See Tuning in to a Preset Station on page 33.
2 Press and hold PRESET/TUNING (EDIT) for
more than 3 seconds.
E1 and the MEMORY indicator flash on the
front panel display.
3 Tune in to preset station A5 by using the
buttons on the front panel.
A5 and the MEMORY indicator flash on the
front panel display.
4 Press PRESET/TUNING (EDIT) again.
The stations stored at the two preset assignments are
exchanged.
PRESET
/TUNING
EDIT
PRESET
/TUNING
EDIT
PRESET/
TUNING
A/B/C/D/E
A/B/C/D/E
Front panel
or
Remote control
1 Press A/B/C/D/E to select the preset station
group.
The preset group letter appears on the front panel
display and changes each time you press A/B/C/D/E.
y
You can select the preset station number with the numeric
buttons (1 to 8) on the remote control if code number 0023
has been set up in the AMP/TUN (or DSP/TUN) position.
DIGITAL
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAINMENT
PRO
LOGIC
ENTERTAINMENT
DSP
6.1/ES
PCM
PRO LOGIC
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
VIRTUAL
PS
PS
PTY
PTY
RT
RT
CT
CT
PTY
PTY
HOLD
HOLD
EON
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
NEWS INFO AFFAIRS SPORT
MEMORY
MEMORY
TUNED
ZONE 2
ZONE 2
VOLUME
dB
dB
ms
ms
SLEEP
SLEEP
DIGITAL
DIGITAL
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAINMENT
PRO
LOGIC
ENTERTAINMENT
DSP
6.1/ES
6.1/ES
PCM
PCM
PRO LOGIC
PRO LOGIC
A
SP
B
VIRTUAL
VIRTUAL
PS
PS
PT
YPTY
RT
CT
PTY
PTY
HOLD
HOLD
EO
NEON
NEWS INFO AF
FNEWS INFO AFFAIRS SPORT
MEMORY
T
ZONE 2
dB
ms
SLEEP
PSPS
PTYPTY
RTRT
CTCT
PTYPTY
HOLDHOLD
EONEON
STEREO
AUTO
NEWS INFO AFFAIRS SPORTNEWS INFO AFFAIRS SPORT
MEMORY TUNED
DTS MOVIE THEATER 1
2
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
DIGITALDIGITAL
DSP
6.1/ES6.1/ES
PCMPCM
PRO LOGICPRO LOGIC
A
SP
B
VIRTUALVIRTUAL
ZONE 2
dB
ms
SLEEP
DIGITAL
DTS MOVIE THEATER 1
2
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
DSP
6.1/ES
PCM
PRO LOGIC
A
SP
B
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZO
SL
Shows the exchange of stations
has been completed.
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
2,4
35
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
RECEIVING RDS STATIONS
RDS (Radio Data System) is a data transmission system
by FM stations in many countries. Stations using this
system transmit an inaudible stream of data in addition to
the normal radio signal.
RDS data contains various information such as PI
(Program Identification), PS (Program Service name),
PTY (Program Type), RT (Radio Text), CT (Clock Time),
EON (Enhanced Other Networks), etc. The RDS function
is carried out among the network stations.
Description of RDS Data
This unit can receive PI, PS, PTY, RT, CT, and EON data
when receiving RDS broadcasting stations.
PS (Program Service name)
mode:
The name of the RDS station being received is displayed.
PTY (Program Type) mode:
The program type on the RDS station being received is
displayed. There are 15 program types to classify RDS
stations. You can make this unit search for a station which
is broadcasting a program of the desired type. See
page 36 for details.
RT (Radio Text) mode:
Information about the program (such as the title of the
song, name of the singer, etc.) on the RDS station being
received is displayed by a maximum of 64 alphanumeric
characters, including the umlaut symbol. If other
characters are used for RT data, they are displayed with
under-bars.
CT (Clock Time) mode:
The current time is displayed and updated every minute.
If the data are accidentally cut off, CT WAIT may
appear.
EON (Enhanced Other Networks):
See page 37.
Changing the RDS Mode
The four modes are available in this unit for displaying
RDS data. When an RDS station is being received, PS,
PTY, RT and/or CT mode indicators that correspond to
the RDS data services offered by the station light up on
the front panel display. Press RDS MODE/FREQ
repeatedly to change the display mode among the RDS
data offered by the transmitting station in the order shown
below. Illumination of the red indicator next to the RDS
mode indicator shows that the corresponding RDS mode
is now selected.
Notes
When an RDS station is being received, do not press RDS
MODE/FREQ until one or more RDS mode indicators light up
on the front panel display. If you press the button before the
indicators light up on the front panel display, the mode cannot
be changed. This is because the unit has not yet received all of
the RDS data on the station.
RDS data not offered by the station cannot be selected.
The RDS data service cannot be utilized by this unit if the
received signal is not strong enough. In particular, the RT mode
requires a large amount of data to be received, so it is possible
that the RT mode may not be displayed even if other RDS
modes (PS, PTY, etc.) are displayed.
RDS data cannot sometimes be received under poor reception
conditions. If so, press TUNING MODE so that the AUTO
indicator goes off from the front panel display. Although the
reception mode is changed to monaural by this operation, when
you change the display to RDS mode, RDS data may be
displayed.
If the signal strength is weakened by external interference
during the reception of an RDS station, the RDS data service
may be cut off suddenly and ...WAIT will appear on the front
panel display.
PS mode
PTY mode
RT mode
CT mode
Frequency
display mode
RDS MODE
/FREQ
36
RECEIVING RDS STATIONS
PTY SEEK Function
If you select the desired program type, the unit
automatically searches all preset RDS stations that are
broadcasting a program of the required type.
1 Press PTY SEEK MODE to set the unit in the
PTY SEEK mode.
The program type of the station being received or
NEWS flashes on the front panel display.
2 Press PRESET/TUNING l / h to select the
desired program type.
The selected program type appears on the front panel
display.
3 Press PTY SEEK START to begin searching
all preset RDS stations.
The selected program type flashes and the PTY
HOLD indicator lights up on the front panel display
while searching for stations.
If a station that is broadcasting a program of the
required type is found, the unit stops at that
station.
If the called station is not the desired one, press
PTY SEEK START again. The unit begins
searching for another station that is broadcasting a
program of the same type.
To cancel this function
Press PTY SEEK MODE twice.
Program types in the PTY mode
There are 15 program types to classify RDS stations.
NEWS News
AFFAIRS Current affairs
INFO General information
SPORT Sports
EDUCATE Education
DRAMA Drama
CULTURE Culture
SCIENCE Science
VARIED Light entertainment
POP M Pops
ROCK M Rock
M.O.R. M Middle-of-the-road music (easy-
listening)
LIGHT M Light classics
CLASSICS Serious classics
OTHER M Other music
Flashes
The selected program
type flashes.
Light up
PTY SEEK
MODE
START
VIRTUAL
PRESET/
TUNING
PTY SEEK
MODE START
DIGITAL
DIGITAL
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAINMENT
PRO
LOGIC
ENTERTAINMENT
DSP
6.1/ES
PCM
PRO LOGIC
B
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
NEWS INFO AFFAIRS SPORT
MEMORY
TUNED
ZZONE 2
dB
ms
SSLEEP
2
13
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
37
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
RECEIVING RDS STATIONS
EON Function
This function uses the EON data service on the RDS
station network. If you simply select the desired program
type (NEWS, INFO, AFFAIRS or SPORT), the unit
automatically searches for all preset RDS stations that are
scheduled to broadcast a program of the required type and
switches from the station being currently received to the
new station when the broadcasts starts.
Note
This function can only be used when an RDS station that offers
the EON data service is being received. When such a station is
being received, the EON indicator lights up on the front
panel display.
1 Make sure that the EON indicator lights up
on the front panel display.
If the EON indicator does not light up, tune in to
another RDS station so that the EON indicator
lights up.
2 Press EON repeatedly to select the desired
program type (NEWS, INFO, AFFAIRS or
SPORT).
The selected program type name indicator lights up
on the front panel display.
If a preset RDS station of the selected program
type starts broadcasting, the unit will automatically
switch from the program being currently received
to that program. The program type name indicator
flashes.
When broadcasting of the required program ends,
the previously received station (or another
program on the same station) is recalled.
To cancel this function
Press EON repeatedly until no program type name lights
up on the front panel display.
Lights up
Flashes
DTS
2
6.1/ES
PCM
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
V
IRTUAL
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
VOLUME
dB
ms
SLEEP
EON
DTS
2
6.1/ES
PCM
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
V
IRTUAL
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
VOLUME
dB
ms
SLEEP
DTS
2
6.1/ES
PCM
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
V
IRTUAL
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
VOLUME
dB
ms
SLEEP
DTS
2
6.1/ES
PCM
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
V
IRTUAL
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
VOLUME
dB
ms
SLEEP
2
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
38
BASIC RECORDING
Recording adjustments and other operations are
performed from the recording components. Refer to the
operation instructions for these components.
1 Turn on the power to the unit and all
connected component.
2 Select the source component you want to
record from.
Front panel
or
Remote control
3 Start playback (or select a broadcast station)
on the source component.
4 Start recording on the recording component.
Notes
Do a test recording before you start an actual recording.
When this unit is set in the standby mode, you cannot record
between other components connected to this unit.
The setting of BASS, TREBLE, BASS EXTENSION,
VOLUME, 3 L/R BALANCE on the SET MENU and DSP
programs does not affect the recorded material.
A source connected to the 6CH INPUT jacks of this unit cannot
be recorded.
S-video and composite video signals pass independently
through this units video circuits. Therefore, when recording or
dubbing video signals, if your video source component is
connected to provide only an S-video (or only a composite
video) signal, you can record only an S-video (or only a
composite video) signal by your VCR.
A given input source is not output on the same REC OUT
channel. (For example, the signal input from VCR 1 IN is not
output on VCR 1 OUT.)
Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording of copyrighted material
may infringe copyright laws.
If you playback a video source that uses scrambled or
encoded signals to prevent it from being dubbed, the
picture itself may be disturbed due to those signals.
Special considerations when
recording DTS software
The DTS signal is a digital bitstream. Attempting to
digitally record the DTS bitstream will result in noise
being recorded. Therefore, if you want to use this unit to
record sources that have DTS signals recorded on them,
the following considerations and adjustments need to be
made.
For LDs, DVDs and CDs encoded with DTS
Only 2-channel analog audio signals may be recorded as
follows:
LDs
Set your LD players left and right outputs to the
analog soundtrack.
DVDs
Use the disc menu to set the DVD players mixed 2-
channel left and right audio outputs to the PCM or
Dolby Digital soundtrack.
CDs
The DTS signal recorded on CDs can only be output
as a digital bitstream, and therefore cannot be
recorded.
INPUT
2
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
2
39
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
Adjusting the Items on the SET
MENU
Adjustment should be made with the remote control.
Note
Some items require extra steps to change to the desired setting.
1 Set the selector dial to the
AMP/TUN (or DSP/TUN)
position.
2 Press SET MENU to enter the SET MENU.
3 Press u/d repeatedly to select the item (1 to
15) you want to adjust.
y
By pressing SET MENU repeatedly, you can select items in the
same order as when pressing d.
4 Press j or i once to enter the setup mode of
the selected item.
The last setting you adjusted appears on the video
monitor or on the front panel display.
SET MENU
ADVANCED OPERATION
3,6
4,5
1
2
The SET MENU consists of 15 items including the
speaker mode setting, center graphic equalizer and
parameter initialization features. Choose the appropriate
item and adjust or select the values as necessary.
y
You can adjust the items on the SET MENU while playing a
source.
We recommend that you adjust the items on the SET MENU
while using a video monitor. It is easier to see the video
monitor than it is to see the front panel display on this unit
while adjusting the items.
Note
The indication on the front panel display is the abbreviation of
the OSD.
1 SPEAKER SET
1A CENTER SP
1B MAIN SP
1C REAR L/R SP
1D LFE/BASS OUT
1E MAIN LEVEL
2 LOW FRQ TEST
3 L/R BALANCE
4 HP TONE CTRL
5 CENTER GEQ
6 INPUT RENAME
7 I/O ASSIGNMENT
8 INPUT MODE
9 PARAM. INI
10 DOLBY D. SET
10A LFE LEVEL
10B D-RANGE
11 DTS LFE LEVEL
12 6.1/ES AUTO
13 SP DELAY TIME
14 DISPLAY SET
15 MEMORY GUARD
SET MENU 1/4
1 SPEAKER SET
2 LOW FRQ TEST
3 L/R BALANCE
4 HP TONE CTRL
:Up/Down
/
–/+ Enter
SET MENU 1/4
1 SPEAKER SET
2 LOW FRQ TEST
3 L/R BALANCE
4 HP TONE CTRL
:Up/Down
/
/+ Enter
2 LOW FRQ TEST
TEST TONE OFF
OUTPUT MAIN L/R
FRQ 88Hz
40
SET MENU
2 LOW FRQ TEST
TEST TONE OFF
OUTPUT MAIN L/R
FRQ 88Hz
Depending on the item, press u/d to select a sub
item.
5 Press j / i repeatedly to change the setting
of the item.
6 Press u/d repeatedly until the current DSP
program appears or simply press one of the
DSP program group button to exit from the
SET MENU.
2 LOW FRQ TEST
TEST TONE ON
OUTPUT MAIN L/R
FRQ 88Hz
1 SPEAKER SET (speaker mode
settings)
Use this feature to select suitable output modes for your
speaker configuration. You must set the output mode
when you use a subwoofer.
Notes
When 96-kHz sampling digital signals are input to this unit,
level adjustments in items 1B and 1D are possible, but those in
items 1A,1C and 1E are not affected.
When 6CH INPUT is selected as the input source, level
adjustments in items 1A through 1E are not affected.
1A CENTER SP (center speaker
mode)
By adding a center speaker to your speaker configuration,
the unit can provide good dialog localization for many
listeners and superior synchronization of sound and
images. The OSD shows a large, small or no center
speaker depending on how you set this item.
Choices: LRG (large), SML (small), NONE
Initial setting: LRG
LRG
Select this if you have a large center speaker. The entire
range of the center channel signal is directed to the center
speaker.
SML
Select this if you have a small center speaker. The low-
frequency signals (90 Hz and below) of the center channel
are directed to the speakers selected with 1D LFE/BASS
OUT.
1A CENTER SP
LRG
SML
NONE
1A CENTER SP
LRG
SML
NONE
or
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the settings of the SET MENU you
adjusted will return to the factory settings. If so, adjust
the items again.
41
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SET MENU
1C REAR L/R SP (rear speaker
mode)
The OSD shows large, small or no rear speakers
depending on how you set this item.
Choices: LRG (large), SML (small), NONE
Initial setting: LRG
LRG
Select this if you have large left and right rear speakers or
if a rear subwoofer is connected to the rear speakers. The
entire range of the rear channel signal is directed to the
left and right rear speakers.
SML
Select this if you have small left and right rear speakers.
The low-frequency signals (90 Hz and below) of the rear
channel are directed to the speakers selected with 1D
LFE/BASS OUT.
NONE
Select this if you do not have rear speakers.
y
This unit is set in the virtual CINEMA DSP mode by selecting
NONE for 1C REAR L/R SP.
NONE
Select this if you do not have a center speaker. All of the
center channel signals are directed to the left and right
main speakers.
1B MAIN SP (main speaker mode)
The OSD shows large or small main speakers depending
on how you set this item.
Choices: LARGE, SMALL
Initial setting: LARGE
LARGE
Select this if you have large main speakers. The entire
range of the left and right main channel signal is directed
to the left and right main speakers.
SMALL
Select this if you have small main speakers. The low-
frequency signals (90 Hz and below) of the main channel
are directed to the speakers selected with 1D LFE/BASS
OUT.
Note
When you select MAIN for 1D LFE/BASS OUT, the low-
frequency signals (90 Hz and below) of the main channel are
directed to the main speakers even if you select SMALL for the
main speaker mode.
1A CENTER SP
LRG
SML
NONE
1B MAIN SP
LARGE
SMALL
1C REAR L/R SP
LRG
SML
NONE
1C REAR L/R SP
LRG
SML
NONE
1C REAR L/R SP
LRG
SML
NONE
1B MAIN SP
LARGE
SMALL
42
SET MENU
1D LFE/BASS OUT (bass out
mode)
LFE signals carry low-frequency effects when this unit
decodes a Dolby Digital or DTS signal. Low-frequency
signals are defined as 90 Hz and below.
Choices: SWFR (subwoofer), MAIN, BOTH
Initial setting: BOTH
SWFR
Select this if you use a subwoofer. The LFE signals are
directed to the subwoofer.
MAIN
Select this if you do not use a subwoofer. The LFE signals
are directed to the main speakers.
BOTH
Select this if you use a subwoofer and you want to mix
the main channel low-frequency signals with the LFE
signals.
Note
The low-frequency signals (90 Hz and below) from all main,
center and rear channels are directed to the LFE channel when
you select the small speaker setting in items 1A, 1B and 1C.
1D LFE/BASS OUT
SWFR
MAIN
BOTH
1D LFE/BASS OUT
SWFR
MAIN
BOTH
1E MAIN LEVEL (main level
mode)
Change this setting if you cannot match the output level
of the center and rear speakers with the main speakers
because of the unusually high-efficiency performance of
the main speakers.
Choices: Normal, 10 dB
Initial setting: Normal
Normal
Select this if you can match the output level of your effect
speakers with that of your main speakers when using the
test tone.
10 dB
Select this if you cannot match the output level of your
effect speakers with that of your main speakers when
using the test tone.
2 LOW FRQ TEST
Use this feature to adjust the output level of the
subwoofer so it matches that of the other speakers in your
configuration. Change the setting with the remote control
while sitting in the listening position.
1 Press j / i to set TEST TONE to ON, and
adjust the volume with VOLUME +/ so you
can hear the tone.
Notes
Do not turn up the volume too high.
If no test tone is heard, turn down the volume, set this unit in
the standby mode and make sure all the necessary connections
are correct.
1E MAIN LEVEL
Normal
10dB
1E MAIN LEVEL
Normal
10dB
1D LFE/BASS OUT
SWFR
MAIN
BOTH
43
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SET MENU
2 Press d to go to OUTPUT and press j / i
to select the speaker you want to compare
with the subwoofer.
If SWFR is selected, the test tone above 90 Hz will
not be output from the subwoofer. The test tone will
not necessarily be output from the selected speakers.
The output mode of the test tone depends on the
settings of 1 SPEAKER SET on the SET MENU.
3 Press d to go to FRQ and press j / i to
select the frequency you want to use.
4 Adjust the volume of the subwoofer with the
controls on the subwoofer so it matches that
of the speaker you are comparing it to.
About the test tone
The test tone is produced by the tone generator.
The tone generator produces a narrow-band noise
centered on a specified frequency by the band pass filter.
You can change this center frequency from 35 Hz through
250 Hz in one-sixth octave steps.
You can use the test tone not only for adjusting the
subwoofer level, but also for checking the low-frequency
characteristics of your listening room. Low-frequency
sounds are especially affected by the listeners position,
speaker placement, subwoofer polarity and other
conditions.
3 L/R BALANCE (balance of the
left and right main speakers)
Use this feature to adjust the balance of the output level
from the left and right main speakers.
Control range: 10 steps for L/R
Initial setting: 0
Press i to decrease the output level for the
left main speaker. Press j for the right main
speaker.
4 HP TONE CTRL (headphone
tone control)
Use this feature to adjust the level of the bass and treble
when you use your headphones.
Control range (dB): 6 to +3
Initial setting: 0 dB for both BASS and TRBL (treble)
5 CENTER GEQ (center graphic
equalizer)
Use this feature to adjust the built-in 5-band graphic
equalizer so that the center speaker tonal quality matches
that of the left and right main speakers. You can select the
100 Hz, 300 Hz, 1 kHz, 3 kHz, or 10 kHz frequencies.
Control range (dB): 6 to +6
Initial setting: 0 dB for 5-band
1 Press d to select a higher frequency and u
to select a lower frequency.
2 Press j / i to adjust the level of that
frequency.
y
You can monitor the center speaker sound while adjusting this
item by using the test tone. Press TEST before starting the
foregoing procedure. TEST DOLBY SUR. appears on the
video monitor, and the test tone starts alternating among the
speakers. Once you begin this procedure, the test tone remains
at the center speaker and you can hear how the sound changes
as you adjust the various frequency levels. To stop the test tone,
press TEST (see pages 22 and 23).
Digital generator
(wide band noise produced)
Noise
Freq.
Center freq. 35 Hz 250 Hz
Band pass filter
44
SET MENU
6 INPUT RENAME
Use this feature to change the name of the input which
appears on the OSD or the front panel display.
1 Press an input selector button (or use INPUT
l / h) to select the input you want to
change the name of.
2 Press j / i to place the _ (under-bar) under
the space or the character you want to edit.
3 Press u/d to select the character you want
to use and j / i to move to the next one.
Press d to change the character in the following
order, or press u to go in the reverse order.
A to Z, a space, 0 to 9, a space, a to z, a space, #,
*, +, and so on.
Follow the foregoing procedure to rename other
inputs.
Note
You can use up to 8 characters to rename the inputs.
4 Press i repeatedly to exit from INPUT
RENAME.
7 I/O ASSIGNMENT
Use this feature to designate the input for the
COMPONENT jacks (A and B) and the DIGITAL
INPUT/OUTPUT jacks (1 to 8) to any sources you
want.
7A [A] [B] (for the COMPONENT
VIDEO jacks)
Initial settings: [A] DVD
[B] D-TV/LD
7B (1) (2) (for the OPTICAL
OUTPUT jacks)
Initial settings: (1) MD/TAPE
(2) CD-R
7C (3) to (6) (for the OPTICAL
INPUT jacks)
Initial settings: (3) CD
(4) CD-R
(5) DVD
(6) D-TV/LD
7D (7) (8) (for the COAXIAL INPUT
jacks)
Initial settings: (7) CD
(8) CBL/SAT
Note
You cannot select an item more than once for the same type of
jack.
8 INPUT MODE (initial input
mode)
Use this feature to designate the input mode for sources
connected to the DIGITAL INPUT jacks when you turn
on this unit (see page 26 for details about the input
mode).
Choices: AUTO, LAST
Initial setting: AUTO
AUTO
Select this to allow this unit to automatically detect the
type of input signal and select the appropriate input mode.
LAST
Select this to set this unit to automatically select the last
input mode used for that source.
9 PARAM. INI (parameter
initialization)
Use this feature to initialize the parameters for each DSP
program within a DSP program group. When you
initialize a DSP program group, all of the parameter
values within that group revert to their initial settings.
1 Press DSP.
2 Press the numeric button (DSP program
group button) on the remote control for the
DSP program you want to initialize.
All of the DSP programs within the selected program
group are initialized.
y
The asterisk mark (*) next to a DSP program group number
indicates that you have changed the parameter values in one or
more DSP programs within that group.
Notes
You cannot initialize the individual DSP programs within a
group separately.
The parameter values of the DSP programs do not change if
you initialize a program group that does not have the asterisk
mark (*).
When 15 MEMORY GUARD is set to ON (see page 46),
you cannot initialize any program groups.
Once you initialize a DSP program group, you cannot
automatically revert to the previous parameter settings.
45
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SET MENU
10 DOLBY D. SET (Dolby Digital
set)
This setting is effective only when this unit decodes
Dolby Digital signals.
10A LFE LEVEL
Use this feature to adjust the output level of the LFE
(low-frequency effect) channel when playing back a
Dolby Digital signal. The LFE signal carries the low-
frequency special effect sound which is only added to
certain scenes.
Control value (dB): 20 to 0
Initial setting: 0 dB for both SPEAKER and
HEADPHONE
Note
Adjust the LFE level according to the capacity of your
subwoofer or headphones.
10B D-RANGE (dynamic range)
Use this feature to adjust the dynamic range.
Choices: MAX, STD (standard), MIN
Initial setting: MAX for both SP (speaker) and HP
(headphones)
Select MAX for feature films.
Select STD for general use.
Select MIN for listening to sources at an extremely
low volume level.
L-LEVEL BST
H-LEVEL CUT
0.0
0.0
1.0
1.0
MAX
11 DTS LFE LEVEL
This setting is effective only when this unit decodes DTS
signals.
Use this feature to adjust the output level of the LFE
(low-frequency effect) channel when playing back a DTS
signal. The LFE signal carries the low-frequency special
effect sound which is only added to certain scenes.
Control range (dB): 10 to +10
Initial setting: 0 dB for both SPEAKER and
HEADPHONE
Note
Adjust the LFE level according to the capacity of your
subwoofer or headphones.
12 6.1/ES AUTO
Use this feature to switch the auto mode of the Dolby
Digital Matrix 6.1 or DTS ES decoder on or off.
Choices: ON, OFF
Initial setting: ON
ON
Select this to allow this unit to automatically turn on the
Dolby Digital Matrix 6.1 or DTS ES decoder when a
signal with the appropriate identification is detected.
OFF
Select this if you want to turn on or off the Dolby Digital
Matrix 6.1 or DTS ES decoder manually by pressing 6.1/
ES on the remote control.
Dialog
level
Input level
Output level
STD
Dialog
level
Input level
Output level
MIN
Dialog
level
Input level
Output level
Note
When you select MIN, the sound output may be faint because
some Dolby Digital signals are not compatible with the
minimum-level dynamic range. In this case, select MAX or
STD.
46
SET MENU
13 SP DELAY TIME
Use this feature to adjust the delay of the center channel
sound. This feature works when this unit decodes a Dolby
Digital or DTS signal. Ideally, the center speaker should
be the same distance from the listening position as the left
and right main speakers. However, in most home
situations, the center speaker is placed in line with the
main speakers. By delaying the sound from the center
speaker, the apparent distance from the center speaker to
the listening position can be adjusted to make it seem the
same as the distance between the left and right main
speakers to the listening position. Adjusting the delay
time for the center speaker is especially important for
giving depth to the dialog.
Control range (ms): 0 to 5
14 DISPLAY SET
BLUE BACK > AUTO/OFF
You can set the OSD background to blue if the video
source is not being reproduced (or the power of the source
component is off).
OSD SHIFT (OSD off-set position)
This setting is used to adjust the vertical position of the
OSD.
DIMMER
You can adjust the brightness of the front panel display.
15 MEMORY GUARD
Use this feature to prevent accidental changes to DSP
program parameter values and other settings on this unit.
Choices: ON, OFF
Initial setting: OFF
Select ON to protect the following features:
DSP program parameters
All SET MENU items
Center, rear speakers and subwoofer levels
The on-screen display (OSD) mode
Notes
When 15 MEMORY GUARD is set to ON, you cannot use
the test tone.
When 15 MEMORY GUARD is set to ON, you cannot select
any other SET MENU items.
L
C
C
R
RL
RR
Center speaker image
y
Increasing the delay by 1 ms simulates moving the speakers
about 30 cm (one foot) farther away from the listening position.
47
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS
2
1
3
Center speaker output
level
Right rear speaker output
level
Left rear speaker output
level
Subwoofer output level
y
Once you press LEVEL, you can also select the speaker(s) to
be adjusted by pressing d. (Pressing u changes the selection
in the reverse order.)
3 Press j / i to adjust the speaker output level.
The control range for the center or left and right
rear speakers is from +10 dB to 10 dB.
The control range for the subwoofer is from 0 dB
to 20 dB.
Notes
If the speaker output mode is set to NONE, the output level of
that speaker cannot be adjusted.
When you adjust the output level with LEVEL, the settings you
made with the test tone will be changed.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the output level of the effect speakers
you adjusted will return to the factory settings. If so,
adjust the output level again.
You can adjust the output level of each effect speaker
(center, left and right rear and subwoofer) while listening
to a music source.
Adjustment should be made with the remote control.
1 Set the selector dial to the
AMP/TUN (or DSP/TUN)
position.
2 Press LEVEL repeatedly to select the
speaker(s) you want to adjust.
Each time you press LEVEL, the selected speaker
changes and appears on the front panel display and
on the video monitor as follows: center, right rear,
left rear and subwoofer.
48
SLEEP TIMER
2
3
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAINMENT
PRO
LOGIC
ENTERTAINMENT
DSP
6.1/ES
PCM
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY
TUNED
ZONE 2
VOLUME
dB
ms
SLEEP
DIGITAL
4 The SLEEP indicator soon lights up on the
front panel display after the sleep timer has
been set.
The display then returns to the previous indication.
Canceling the Sleep Timer
Press SLEEP repeatedly until SLEEP OFF
appears on the front panel display.
After a few seconds, SLEEP OFF disappears, the
SLEEP indicator goes off and the display returns
to the previous indication.
y
The sleep timer setting can also be canceled by setting this unit
in the standby mode by using STANDBY on the remote control
(or STANDBY/ON on the front panel) or by disconnecting the
AC power cord from the AC outlet.
DTS MOVIE THEATER 1
DTS
MOVIE
THEATER
1
2
DOLBY DIGITAL
DOLBY
DIGITAL
PRO LOGIC ENTERTAINMENT
PRO
LOGIC
ENTERTAINMENT
DSP
6.1/ES
6.1/ES
PCM
PCM
PRO LOGIC
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
PS
PTY
RT
CT
PTY
PTY
HOLD
HOLD
EON
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
NEWS INFO AFFAIRS SPORT
MEMORY
TUNED
ZONE 2
VOLUME
dB
ms
ms
SLEEP
DIGITAL
Use this feature to automatically set this unit in the
standby mode after the amount of time you have set. The
sleep timer is useful when you are going to sleep while
this unit is playing or recording a source. The sleep timer
also automatically turns off the external components
connected to AC OUTLET(S).
The sleep timer can only be set with the remote control.
y
By connecting a commercially available timer to this unit, you
can also set a wake-up timer. Refer to the operation instructions
of the timer.
Setting the Sleep Timer
1 Select a source and start playback on the
source component.
2 Set the selector dial to a
position other than the TV
position.
3 Press SLEEP repeatedly
to set the amount of time
before this unit
automatically turns off.
Each time you press SLEEP, the front panel display
changes as shown below.
49
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
REMOTE CONTROL FEATURES
The remote control can operate this unit as well as other YAMAHA A/V components. To control the components from
other manufacturers (or some from YAMAHA), you must set up the remote control with the manufacturer codes.
This remote control also has a sophisticated feature: Learn. The Learn feature allows it to acquire functions from the
remote controls of other components in your system (or other household appliances) equipped with a infrared remote
control receiver. This feature makes it possible for you to reduce the number of remote control in your entertainment
room.
Notes
For the operating distance of the remote contorol and notes about batteries, see pages 3 and 8.
For the name and function of each part and button, see pages 6 to 8.
If the memory on the remote control becomes full, no further learning is possible, even if there are still some programmable buttons
available (see page 55).
Selector Dial
There are 9 positions that you can select to control connected components with this remote control. For example, if the
CD position is selected, the remote control is set in the CD operation mode, allowing the CD player to be controlled by
the buttons on the remote control. When turning the selector dial, the position changes as follows:
Selector
dial
AMP/TUN
You can perform the basic operations of
this unit. See pages 6 and 7.
CD
The code for a YAMAHA CD
player is factory-set.
CBL/SAT
A cable TV or satellite tuner can be controlled.
VCR
A VCR can be controlled.
TV
A TV can be controlled.
TAPE/MD
The code for a YAMAHA tape deck is factory-
set. Be sure to set the proper code when
operating an MD recorder or CD recorder.
DVD/LD & DVD MENU
An LD player can be controlled in
the DVD/LD position. A DVD player
can be controlled in the DVD/LD and
DVD MENU positions. The code for
a YAMAHA DVD player is factory-
set. If the remote control does not
operate your YAMAHA DVD player,
you need to set the code number
0048.
DSP/TUN
This unit can be controlled and DSP
programs can be selected directly.
Note
The general operational buttons on the remote control differ depending on the position of the selector dial. See the following pages
for details.
50
REMOTE CONTROL FEATURES
2
1
3
5
4
@
#
!
2
5
4
1
3
6
Commonly Used Buttons in Any
Position of the Selector Dial
Regardless of the position of the selector dial, you can
control this unit and your TV with the following buttons.
Note
You have to set up the code for your TV in the TV position
before you can control the TV.
Controlling this unit
See pages 6 and 7.
1 STANDBY
2 POWER
3 VOLUME +/
4 SLEEP
Note
If you have set up the code for your TV and set the selector dial
to the TV position, this button is used to set the sleep timer for
the TV.
5 MUTE
Note
If you have set up the code for your TV and set the selector dial
to the TV position, this button is used to mute the TV sound.
Controlling your TV
! TV POWER
@ TV INPUT
# TV VOLUME +/
Controlling the Components
Connected to This Unit
The example below describes the procedure for
controlling a YAMAHA CD player.
1 Set the selector dial to the
CD position.
2 Turn on the power.
3 Press INPUT.
The indicator lights up for
about 3 second.
4 Press CD while the
indicator is lit.
5 Press p.
See page 51 for the CD player
operation buttons.
6 Adjust the volume.
If you set the remote control with the manufacturer
codes listed from page i at the end of this
manual, you can control other brands of components.
See Setting the Manufacturer Codes on page 54 for
details.
51
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
REMOTE CONTROL FEATURES
A/B/C/D/E
A/B/C/D/E
Button Names and Functions in Each Position
TAPE/MD position (tape deck, MD recorder or CD recorder)
Select the TAPE/MD position.
r Rec/Pause (tape/MD)
p Play
b DIR A (tape)
This button selects the playing direction of deck A.
Skip (MD/CD-R)
w Rewind (tape)
Search (MD/CD-R)
Numeric buttons (MD/CD-R)
INDEX (CD-R)
+10 (MD/CD-R)
Deck A/B (tape)
This button selects deck A or B on a double-cassette
tape deck.
DISPLAY (MD/CD-R)
e Pause (MD/CD-R)
a DIR B (tape)
This button selects the playing direction of deck B.
Skip + (MD/CD-R)
AV POWER
(Tape) This button turns on the tape deck that has a remote control with a power button if you have set up the code for another manufacturer.
(MD) This button turns on the MD recorder that has a remote control with a power button if you have set up the code for another manufacturer.
(CD-R) This button turns on the CD recorder that has a remote control with a power button if you have set up the code for another manufacturer.
CD position
Select the CD position.
DISC SKIP /+
(for a CD player with CD changer)
p Play
b Skip
w Search
Numeric buttons
INDEX
+10
DISPLAY
e Pause
YAMAHA CD player (factory settings): Pause/Stop
a Skip +
s Stop
YAMAHA CD player (factory settings): Pause/Stop
f Search
AV POWER
This button turns on the CD player that has a remote
control with a power button if you have set up the
code for another manufacturer.
y Pause/Stop function
Press the button once to give
a pause in operation and press
once more to stop operation.
Notes
The dark-shaded buttons do not function even if you have set up the manufacturer code.
Some of them may not function depending on the component you have. Refer to the operation instructions for your component.
You can program a remote control function to all buttons except DSP and INPUT. See Programming a New Remote
Control Function on page 55.
s Stop
f Fast forward (tape)
Search (MD/CD-R)
52
REMOTE CONTROL FEATURES
A/B/C/D/E
A/B/C/D/E
DVD/LD position
Select the DVD/LD position.
DISC SKIP /+ (DVD)
p Play
b Skip (DVD)
Skip/Chapter (LD)
w Search
Numeric buttons
INDEX/Time (DVD)
Chapter/Time (LD)
+10
DISPLAY
e Pause
a Skip + (DVD)
Skip/Chapter + (LD)
s Stop
f Search
AV POWER
(DVD) This button turns on the YAMAHA DVD player if you have set up the code number 0048. Also this button turns on the DVD player
that has a remote control with a power button if you have set up the code for another manufacturer.
(LD) This button turns on the LD player that has a remote control with a power button if you have set up the code for another manufacturer.
DVD MENU position
Note
DVD MENU operations cannot be performed for some DVD players.
Select the DVD MENU position.
DISC SKIP /+
Return
Menu select
Menu left
TITLE
Numeric buttons
INDEX
+10
DISPLAY
Menu up
Menu right
Menu down
MENU
AV POWER
This button turns on the YAMAHA DVD player if you have set up the code number 0048. Also this
button turns on the DVD player that has a remote control with a power button if you have set up the
code for another manufacturer.
Notes
The dark-shaded buttons do not function even if you have set up the manufacturer code.
Some of them may not function depending on the component you have. Refer to the operation instructions for your component.
You can program a remote control function to all buttons except DSP and INPUT. See Programming a New Remote
Control Function on page 55.
53
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
REMOTE CONTROL FEATURES
A/B/C/D/E
A/B/C/D/E
A/B/C/D/E
VCR position
Select the VCR
position.
VCR REC
Press this button twice
to start recording.
p Play
w Rewind
Numeric
buttons
Ch enter/Recall
_/_ _
CH /+
DISPLAY
e Pause
s Stop
f
Fast forward
AV POWER
This button turns on a VCR that has a remote control with a power
button if you have set up the code for your VCR.
CBL/SAT position
Select the CBL/SAT
position.
CH /+
Menu select
Menu left
Recall
Numeric buttons
Ch enter
_/_ _
DISPLAY/
Guide (SAT)
Menu up
Menu right
Menu down
MENU
AV POWER
This button turns on a cable TV/satellite tuner that has a remote
control with a power button if you have set up the code for your cable
TV/satellite tuner.
TV position
Note
You can control your VCR if you have set up the code for it in
the VCR position.
Select the TV
position.
VCR REC
Press this button twice.
p VCR play
w VCR rewind
TV POWER
This button turns on a TV that
has a remote control with a
power button if you have set up
the code for your TV.
TV VOL +/
TV INPUT
Numeric buttons
Ch enter/Recall
_/_ _
CH /+
DISPLAY
e VCR pause
s VCR stop
f
VCR fast forward
VCR power
TV SLEEP
TV MUTE
Notes
The dark-shaded buttons do not function even if you have set up the manufacturer code.
Some of them may not function depending on the component you have. Refer to the operation instructions for your component.
You can program a remote control function to all buttons except DSP and INPUT. See Programming a New Remote
Control Function on page 55.
54
REMOTE CONTROL FEATURES
Setting the Manufacturer Code
You can set up the code for the manufacturer of your
component in each position of the selector dial.
1 Turn on your component to be used.
2 Set the selector dial to the
desired position for the
component (TAPE/MD, CD,
DVD/LD, etc.).
3 Press j / i at the same time for about
4 seconds.
The indicator flashes twice.
4 Use the numeric buttons
to enter the four-digit
manufacturer code for the
component to be used.
Make sure that the
indicator flashes twice.
If the indicator does not flash
or flashes rapidly several
times, repeat step 3 and re-
enter the code.
5 Press AV POWER (or any other button) to
check if you have set up the code correctly.
If your component cannot be
controlled with the remote
control, try setting another
code for the same
manufacturer.
Notes
You can set up only one code for one position.
In the DVD/LD and DVD MENU positions:
Be sure to set the selector dial to the DVD/LD position before
entering the code for the DVD/LD player. The code set up in
the DVD/LD position is also simultaneously set up in the DVD
MENU position. You cannot set up the code for a DVD player
when the selector dial is set to the DVD MENU position.
If your component does not respond to any of the codes listed
for the manufacturer, you can program functions from the other
remote controls functions (see page 55 for details).
If you have already programmed a remote control function to a
button, the function by programming (see page 55) takes
priority over the set up manufacturer codes function.
To use a second (and third) VCR
You can control a second (and third) VCR in the CBL/
SAT and DVD MENU positions if a cable TV/satellite
tuner or DVD player is not being used.
Note
If you want to control a second (and third) VCR in the DVD
MENU position, you must set up the code for an LD player in
the DVD/LD position.
1 Turn on the VCR to be used.
2 Set the selector dial to the
CBL/SAT or DVD MENU
position.
3 Press j / i at the same time for about
4 seconds.
The indicator flashes twice.
4 Use the numeric buttons
to enter the four-digit
code for the second (and
third) VCR. Make sure that
the indicator flashes
twice.
If the indicator does not flash
or flashes rapidly several
times, repeat step 3 and re-
enter the code.
5 Press AV POWER (or any other button) to
check if you have set up the code correctly.
If the VCR cannot be
controlled with the remote
control, try setting another
code for the same
manufacturer.
55
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
REMOTE CONTROL FEATURES
Programming a New Remote
Control Function (Learn Feature)
If you want to program functions not included in the basic
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. You can program
functions to all buttons except DSP and INPUT in all
positions of the selector dial other than AMP/TUN and
DSP/TUN, so the buttons are programmable
independently for each position of the selector dial.
y
You can program about 60 buttons.
Note
This remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn
most of the other remote controls functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
1 Set the selector dial to the
desired position for the
component to be
programmed.
2 Place this remote control and the other
remote control about 10 to 40 mm (3/8 to
1-1/2) apart on a flat surface so that their
infrared transmitters are aimed at each other.
10 to 40 mm (3/8 to 1-1/2)
3 Press and hold e and p at the same time
for about 4 seconds.
The indicator flashes twice.
Note
If you do not press any button within 30 seconds during steps 4
and 5, the indicator flashes twice and the learning process is
canceled. If this happens, start over from step 3.
4 Press the button for which you want to
program the new function.
The indicator lights up.
Lights up
5 Press and hold the button on the other
remote control that has the function you
want to program into this remote control
until the indicator goes off.
Goes off
Notes
If this remote control cannot receive the signals from other
remote control, the indicator flashes rapidly.
When the memory is full, the indicator flashes twice and this
remote control cannot acquire any more functions. Clear
unnecessary programmed functions to allow this remote control
to acquire new functions.
If you do not press any button within 30 seconds after step 5,
the indicator flashes twice. This indicates that the learning
process is complete and the remote control has exited from the
learning mode.
6 Repeat steps 4 and 5 to program additional
functions.
7 Press DSP or INPUT, or turn the selector dial
to exit from the learning mode.
The indicator flashes twice.
Notes
Even if the batteries in the other remote control have enough
power to transmit signals for operation, they may not have
enough power to transmit signals to this remote control.
When the remote controls are either too close together or too
far apart, you may not be able to program this remote control.
Direct sunlight interferes with infrared rays.
Memory back-up
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
56
REMOTE CONTROL FEATURES
Returning to the Factory Setting
To return to the factory-set codes
and to clear the learned functions
in all positions
1 Press j / i at the same time for about
4 seconds.
The indicator flashes twice.
2 Enter the code number 9990.
Make sure that the indicator flashes twice.
To return to the factory-set codes
and to clear the learned functions
in each position
1 Set the selector dial to the
position for the
component to be returned
to the factory setting.
2 Press j / i at the same time for about
4 seconds.
The indicator flashes twice.
3 Enter the code number 0000.
Make sure that the indicator flashes twice.
The following codes are factory set.
Selector dial
position
Component
Code
TV TV 0101
CBL/SAT Satellite tuner 0006
VCR VCR 0002
DVD/LD DVD player
0008 (YAMAHA DVD
player)
CD CD player
0005 (YAMAHA CD
player)
TAPE/MD Tape deck
0004 (YAMAHA Tape
deck)
AMP/TUN this unit 0003
DSP/TUN this unit 0013
We recommend that you write all the code numbers you
have set on the Quick Reference Card.
57
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SOUND FIELD PROGRAM
This unit incorporates a sophisticated, multi-program digital sound field processor (DSP). This processor allows you to
electronically expand and change the shape of the audio sound field from both audio and video sources, creating a
theater-like experience in your listening room. You can create outstanding audio sound field by selecting a suitable DSP
program (this will, of course, depend on what you are listening to) and making desired adjustments.
The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in
mind that most of these are precise digital recreations of actual acoustic environments.
Note
Select the DSP program that you feel sounds best regardless of the name and description given for it below.
Hi-Fi DSP Programs
For audio sources: Nos. 1 to 5
ADDITIONAL INFORMATION
No. Program (group) Sub-program Features
1 CONCERT HALL
A large round concert hall with a rich surround effect. Pronounced reflections
from all directions emphasize the extension of sounds. The sound field has a great
deal of presence, and your virtual seat is near the center, close to the stage.
2 CHURCH This program recreates the acoustic environment of a big church with a high
dome and columns along each side. The reverberation delay is very long while
the early reflections are smaller than with other sound field programs.
3 JAZZ CLUB
This is the sound field at stage front in The Bottom Line, a famous New York
jazz club. The floor can seat 300 people to the left and right in a sound field
offering a real and vibrant sound.
4 ROCK CONCERT
The ideal program for lively, dynamic rock music. The data for this program was
recorded at LAs hottest rock club. The listeners virtual seat is at the center-left
of the hall.
5 ENTERTAINMENT Disco This program recreates the acoustic environment of a lively disco in the heart of a
big city. The sound is dense and highly concentrated. It is also characterized by a
high-energy, immediate sound.
5ch Stereo
Note
If 1A CENTER SP on the SET MENU is set to NONE, no sound is output from the center speaker.
Using this program increases the listening position range. This is a sound field
suitable for background music at parties.
58
SOUND FIELD PROGRAM
No.
MOVIE
THEATER 1
Analog,
PCM, Dolby
Digital in
2-channel
DGTL Spectacle *
1
Spectacle 6.1 *
2
DTS Spectacle *
1
Spectacle ES *
2
This program creates the extremely wide sound
field of a 70-mm movie theater. It precisely
reproduces the source sound in detail, making
both the video and the sound field incredibly real.
This is ideal for any kind of video source encoded
with Dolby Surround, Dolby Digital or DTS
(especially large-scale movie productions).
Sci-Fi 70 mm Sci-Fi
Analog,
PCM, Dolby
Digital in
2-channel
DGTL Sci-Fi *
1
Sci-Fi 6.1 *
2
DTS Sci-Fi *
1
Sci-Fi ES *
2
This program clearly reproduces dialog and sound
effects in the latest sound form of science fiction
films, thus creating a broad and expansive
cinematic space amid the silence. You can enjoy
science fiction films in a virtual-space sound field
that includes Dolby Surround, Dolby Digital and
DTS-encoded software employing the most
advanced techniques.
Program
(group)
8
Sub-program
Input source Features
Spectacle 70 mm Spectacle
Dolby
Digital
DTS
Dolby
Digital
DTS
CINEMA DSP Programs
For audio-video sources: Nos. 5 to 7
For movie programs: Nos. 8 to 10
No. Program (group) Sub-program Features
5 ENTERTAINMENT Game
This program adds a deep and spatial feeling to video game sounds.
7 MONO MOVIE
This program is provided for reproducing monaural video sources (such as old
movies). The program produces the optimum reverberation to create sound depth
by using only the presence sound field.
6 TV SPORTS Although the presence sound field is relatively narrow, the surround sound field
employs the sound environment of a large concert hall. With this program, you
can enjoy watching various TV programs such as news, variety shows, music
programs or sports programs. In a stereo broadcast of a sports game, the
commentator is oriented at the center position, and the shouts and the
atmosphere in the stadium spread on the surround side, while their spread to the
rear is properly restrained.
59
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SOUND FIELD PROGRAM
9 MOVIE
THEATER 2
Analog,
PCM, Dolby
Digital in
2-channel
DGTL Adventure *
1
Adventure 6.1 *
2
DTS Adventure *
1
Adventure ES *
2
This program is ideal for precisely reproducing
the sound design of the newest 70-mm and
multichannel soundtrack films. The sound field
is made to be similar to that of the newest movie
theaters, so the reverberations of the sound field
itself are restrained as much as possible.
General 70 mm General Analog,
PCM, Dolby
Digital in
2-channel
DGTL General *
1
General 6.1 *
2
DTS General *
1
General ES *
2
This program is for reproducing sounds from
70-mm and multichannel soundtrack films, and
is characterized by a soft and extensive sound
field. The presence sound field is relatively
narrow. It spatially spreads all around and
toward the screen, restraining the echo effect of
conversations without losing clarity. For the
surround sound field, the harmony of music or
chorus sounds beautifully in a wide space at the
rear of the sound field.
Adventure 70 mm Adventure
Dolby
Digital
DTS
Dolby
Digital
DTS
No.
Program
(group)
Sub-program
Input source
Features
60
SOUND FIELD PROGRAM
No.
q/DTS
SURROUND
Normal/
Matrix
6.1/ES
Analog, PCM,
Dolby Digital
in 2-channel
*1 The Dolby Digital Matrix 6.1 or DTS ES decoder is off.
*2 The Dolby Digital Matrix 6.1 or DTS ES decoder is on. The c indicator lights up on the front panel display.
y
If a Dolby Digital signal or DTS signal is input when the input mode is set to AUTO, the DSP program will be automatically
switched to the Dolby Digital playback sound field or DTS playback sound field.
If Dolby Digital Surround EX software or DTS ES software is played when 12 6.1/ES AUTO on the SET MENU is set to ON, the
Dolby Digital Matrix 6.1 or DTS ES decoder will automatically turn on and the corresponding DSP program will be selected.
6.1/ES on the remote control can be used to turn the Dolby Digital Matrix 6.1 or DTS ES decoder on or off during Dolby Digital 5.1-
channel source or DTS 5.1-channel source playback.
Notes
The x indicator does not light up when selecting the sub-program Normal of the q/DTS SURROUND program.
If 1A CENTER SP on the SET MENU is set to NONE, no sound is output from the center speaker.
The effect sound is output from the main speakers when a monaural source is played with CINEMA DSP program groups 5 (Game)
and 6 to 9.
Program
(group)
10 PRO LOGIC/Normal
DOLBY DIGITAL/
Normal *
1
DOLBY DIGITAL/
Matrix 6.1 *
2
DTS DIGITAL SUR./
Normal *
1
DTS DIGITAL SUR./
ES *
2
The built-in decoder precisely reproduces sounds
and sound effects from sources.
The highly efficient decoding process improves
crosstalk and channel separation, and makes sound
positioning smoother and more precise.
In this program, the digital sound field processor is
not turned on.
Enhanced PRO LOGIC/Enhanced Analog, PCM,
Dolby Digital
in 2-channel
DOLBY DIGITAL/
Enhanced *
1
DOLBY DIGITAL/
Enhanced 6.1 *
2
DTS DIGITAL SUR./
Enhanced *
1
DTS DIGITAL SUR./
Enhanced ES *
2
This program ideally simulates the multi-surround
speaker systems of the 35-mm film theaters. Dolby
Pro Logic decoding, Dolby Digital decoding or
DTS decoding and digital sound field processing
create precise effects without altering the original
sound orientation.
The surround effects produced by this sound field
wrap around the viewer naturally from the back to
the left and right, and toward the screen.
Sub-program
Input source Features
Dolby Digital
DTS
Dolby Digital
DTS
61
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SOUND FIELD PROGRAM
MOVIE THEATER Programs
Most movie software has 4-channel (left, center, right and surround) sound information encoded by Dolby Surround
matrix processing and stored on the left and right tracks. These signals are processed by the Dolby Pro Logic decoder.
The MOVIE THEATER programs are designed to recreate the spaciousness and delicate nuances of sound that tend to
be lost in the encoding and decoding processes.
The 6-channel soundtracks found on 70-mm film produce precise sound field localization and rich, deep sound without
using matrix processing. This units MOVIE THEATER 70 mm programs provide the same quality of sound and sound
localization that 6-channel soundtracks do. The built-in Dolby Digital or DTS decoder brings the professional-quality
sound designed for movie theaters into your home. With the units MOVIE THEATER programs, you can recreate a
dynamic sound that gives you the feeling of being at a public theater in your listening room by using Dolby Digital or
DTS technology.
Dolby Pro Logic + DSP sound field effect
These programs express an immense sound field and a
large surround effect. They also give depth to the sound
from the main speakers to recreate the realistic sound of a
Dolby Stereo theater.
Presence DSP
sound field
Right surround DSP
sound field
Left surround DSP
sound field
Presence DSP
sound field
Surround DSP
sound field
Dolby Digital/DTS + DSP sound field effect
These programs use YAMAHAs tri-field DSP processing
on each of the Dolby Digital or DTS signals for the front,
left surround and right surround channels. This processing
enables this unit to reproduce the immense sound field
and surround expression of a Dolby Digital- or DTS-
equipped movie theater without sacrificing the clear
separation of all channels.
62
SOUND FIELD PROGRAM PARAMETER EDITING
What is a sound field?
What really creates the rich, full tones of a live instrument
are the multiple reflections from the walls of the room. In
addition to making the sound live, these reflections
enable us to tell where the player is situated, and the size
and shape of the room in which we are sitting.
Elements of a sound field
In any environment, in addition to the direct sound
coming straight to our ears from the players instrument,
there are two distinct types of sound reflections that
combine to make up the sound field:
Early reflections
Reflected sounds reach our ears extremely rapidly
(50 ms 100 ms after the direct sound), after reflecting
from one surface only for example, from the ceiling or
a wall. These reflections fall into specific patterns as
shown in the diagram on page 64 for any particular
environment, and provide vital information to our ears.
Early reflections actually add clarity to the direct sound.
Reverberations
These are caused by reflections from more than one
surface walls, ceiling, the back of the room so
numerous that they merge together to form a continuous
sonic afterglow. They are non-directional, and lessen
the clarity of the direct sound.
Direct sound, early reflections and subsequent
reverberation taken together help us to determine the
subjective size and shape of the room, and it is this
information that the digital sound field processor
reproduces in order to create sound fields.
If you could create the appropriate early reflections and
subsequent reverberations in your listening room, you
would be able to create your own listening environment.
The acoustics in your room could be changed to those of
a concert hall, a dance floor, or virtually any size room at
all. This ability to create sound fields at will is exactly
what YAMAHA has done with the digital sound field
processor.
Sound Field Program Parameters
DSP programs consist of some parameters to determine
the apparent room size, reverberation time, distance from
you to the performer, etc. In each program, these
parameters are set with values precisely calculated by
YAMAHA to create a sound field unique to the program.
It is recommended to use DSP programs without
changing the values of parameters; however, this unit also
allows you to create your own sound fields. Starting with
one of the built-in programs, you can adjust those
parameters.
Each DSP program has a set of parameters that allow you
to change the characteristics of the acoustic environment
to precisely create the effect you want. These parameters
correspond to the many natural acoustic factors that create
the sound field you experience in an actual concert hall or
other listening environment. The size of the room, for
example, affects the length of time between the early
reflections. The ROOM SIZE parameter provided in
many of the DSP programs alters the timing between
these reflections, thus changing the shape of the room
you are listening. In addition to room size, the shape of
the room and the characteristics of its surfaces have a
significant effect on the final sound. Surfaces that absorb
sound, for example, cause the reflections and
reverberations to die out more quickly, while highly
reflective surfaces allow the reflections to carry on for a
longer period of time. The digital sound field parameters
allow you to control these and many other factors that
contribute to your personal sound field, allowing you to
essentially redesign the concert halls, theaters, etc.
provided to create custom-tailored listening environments
that ideally match your mood and music.
See Digital Sound Field Parameter Descriptions on
pages 64 to 67.
63
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SOUND FIELD PROGRAM PARAMETER EDITING
Changing Parameter Settings
You can enjoy good quality sound with the factory-set
parameters. Although you do not have to change the
initial settings, you can change some of the parameters to
better suit the input source or your listening room.
Adjustments should be made with the remote control.
y
We recommend that you edit the parameter while using a video
monitor. It is easier to see the video monitor than it is to see the
front panel display.
1 Set the selector dial to the DSP/TUN (or
AMP/TUN) position.
or
2 Turn on the video monitor
and press ON SCREEN
repeatedly to select the
full display mode.
3 Select a DSP program you want to adjust.
2
5
4
1
3
3
Program No. Program name (group)
Cursor
Parameters
Example of the ROCK CONCERT
4 Press u/d to select the
parameter.
5 Press j / i to change the
parameter value.
y
When you set the parameter to a value other than the factory-
set value, an asterisk mark (*) appears by the parameter name
on the video monitor.
6 Repeat steps 3 to 5 above as necessary to
change other program parameters.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter value you edited will
return to the factory setting. If so, edit the parameter
value again.
Resetting a Parameter to the
Factory-set Value
To reset some of the parameters
to the factory-set values
Select the parameter you want to reset. Then press and
hold j or i until the value temporarily stops at the
factory-set value. The asterisk mark (*) by the parameter
name disappears on the video monitor.
To reset all of the parameters to
the factory-set values
Use 9 PARAM. INI on the SET MENU to reset all of
the parameter values of all DSP programs within the
selected group to the factory-set values (see page 44).
This operation resets all of the parameter values of all
DSP programs within that group to the factory-set values.
Notes
The available parameters may be displayed on more than one
OSD page for some of the programs. To scroll through pages,
press u/d.
You cannot change parameter values when 15 MEMORY
GUARD on the SET MENU is set to ON. If you want to
change the parameter values, set 15 MEMORY GUARD to
OFF (see page 46).
P04 ROCK CONCERT
INIT.DLY
15ms
5
7%
REV.TIME
LIVENESS
REV.DELAY
REV.LEVEL
100ms
1.6s
64
SOUND FIELD PROGRAM PARAMETER EDITING
Digital Sound Field Parameter Descriptions
You can adjust the values of certain digital sound field parameters so the sound fields are recreated accurately in your
listening room.
Note
Not all of the following parameters can be found in every program.
INIT.DLY (initial delay)
(P.INIT.DLY for the presence sound field)
Function: This parameter changes the apparent distance from the sound source by adjusting the delay between the
direct sound and the first reflection heard by the listener.
Control range: 1 99 msec
Description: The smaller the value, the closer the sound source seems to the listener. The larger the value, the farther
the apparent distance seems. For a small room, this parameter would be set to a small value, for a large
room, set it to a large value.
INT. DLY INT. DLY INT. DLY
Level
Time
Level
Sound source
Early
reflections
Time
Level
Time
Sound source
Reflection surface
Small value = 1 ms
Large value = 99 ms
ROOM SIZE
(P.ROOM SIZE for the presence sound field)
Function: This parameter adjusts the apparent size of the surround sound field. The larger the value, the larger the
surround sound field becomes.
Control range: 0.1 2.0
Description: As the sound is repeatedly reflected around a room, the larger the hall is, the longer the time between
the original reflected sound and the subsequent reflections. By controlling the time between the
reflected sounds, you can change the apparent size of the virtual venue. Changing this parameter from
one to two, doubles the apparent length of the room.
Level
Time
Level
Time
Sound source
Early reflections
Level
Time
Sound source
First reflection
Small value = 0.1
Large value = 2.0
65
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SOUND FIELD PROGRAM PARAMETER EDITINGSOUND FIELD PROGRAM PARAMETER EDITING
LIVENESS
Function: This parameter adjusts the reflectivity of the virtual walls in the hall by changing the rate at which the
early reflections decay.
Control range: 0 10
Description: The early reflections of a sound source decay much faster in a room with acoustically absorbent wall
surfaces than in one which has highly reflective surfaces. A room with acoustically absorbent surfaces
is referred to as dead, while a room with highly reflective surfaces is referred to as live. The
LIVENESS parameter lets you adjust the early reflection decay rate, and thus the liveness of the
room.
Level
Time
Dead
Level
Sound source
Time
Level
Time
Live
Sound source
Small reflected sound
Small value = 0
Large reflected sound
Large value = 10
S.DELAY (surround delay)
Function: This parameter adjusts the delay between the direct sound and the first reflection in the surround sound
field.
Control range: 0 49 msec (The range depends on the signal format.)
S.INIT.DLY (surround initial delay)
Function: This parameter adjusts the delay between the direct sound and the first reflection on the surround side
of the sound field. You can only adjust this parameter when at least two front channels and two rear
channels are used.
Control range: 1 49 msec
S.ROOM SIZE (surround room size)
Function: This parameter adjusts the apparent size of the surround sound field.
Control range: 0.1 2.0
S.LIVENESS (surround liveness)
Function: This parameter adjusts the apparent reflectivity of the virtual walls in the surround sound field.
Control range: 0 10
66
SOUND FIELD PROGRAM PARAMETER EDITING
RC.INIT.DLY (rear center initial delay)
Function: This parameter adjusts the delay between the direct sound and the first reflection in the rear center
sound field.
Control range: 1 49 msec
RC.ROOM SIZE (rear center room size)
Function: This parameter adjusts the apparent size of the rear center sound field.
Control range: 0.1 2.0
RC.LIVENESS (rear center liveness)
Function: This parameter adjusts the apparent reflectivity of the virtual wall in the rear center sound field.
Control range: 0 10
REV.TIME (reverberation time)
Function: This parameter adjusts the amount of time it takes for the dense, subsequent reverberation sound to
decay by 60 dB (at 1 kHz). This changes the apparent size of the acoustic environment over an
extremely wide range.
Control range: 1.0 5.0 sec
Description: Set a longer reverberation time for dead sources and listening room environments and a shorter time
for live sources and listening room environments.
60 dB
REV. TIME REV. TIME REV. TIME
60 dB 60 dB
Level
Time
Level
Time
Sound source
Early reflections
Level
Time
Short reverberations
Long reverberations
Small value = 1.0 s
Large value = 5.0 s
Reverberations
Reverberations
Reverberations
Sound source
67
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SOUND FIELD PROGRAM PARAMETER EDITINGSOUND FIELD PROGRAM PARAMETER EDITING
REV.DELAY (reverberation delay)
Function: This parameter adjusts the time difference between the beginning of the direct sound and the beginning
of the reverberation sound.
Control range: 0 250 msec
Description: The larger the value, the later the reverberation sound begins. A later reverberation sound makes you
feel like you are in the larger acoustic environment.
REV. LEVEL
60 dB
(dB)
REV.
DELAY
REV TIME
Level
Sound source
Reverberation
Time
REV.LEVEL (reverberation level)
Function: This parameter adjusts the volume of the reverberation sound.
Control range: 0 100%
Description: The larger the value, the stronger the reverberation becomes.
Level
Sound source
Time
CT.DELAY (center delay)
LS.DELAY (left surround delay)
RS.DELAY (right surround delay)
Function: These parameters adjust the sound delay for each channel in 5 channel stereo mode.
Control range: 0 50 msec
68
TROUBLESHOOTING
Refer to the chart below when the unit does not function properly. If the problem you are experiencing is not listed
below or if the instruction below does not help, set this unit in the standby mode, disconnect the power cord and contact
the nearest authorized YAMAHA dealer or service center.
General
Problem Cause Remedy
Refer to
page
The unit fails to turn
on when STANDBY/ON
(or POWER) is
pressed, or enters in
the standby mode
soon after the power
has been turned on.
19
The power cord is not connected or the plug
is not completely inserted.
Firmly connect the power cord.
The IMPEDANCE SELECTOR switch on
the rear panel is not fully set to the left or
right position.
Set the switch fully to the left or right position
when the unit is in the standby mode.
The protection circuitry has been
activated.
Make sure all speaker wire connections on
this unit and on all speakers are secure and
that the wire for each connection does not
touch anything other than its respective
connection.
No sound and/or no
picture.
Incorrect input or output cable connections. Connect the cables properly. If the problem
persists, the cables may be defective.
An appropriate input source has not been
selected.
Select an appropriate input source with
INPUT l / h or 6CH INPUT (or the input
selector buttons).
The speaker connections are not secure. Secure the connections.
The main speakers to be used have not
been selected properly.
Select the main speakers with SPEAKERS A
and/or B.
The volume is turned down. Turn up the volume.
The sound is muted. Press MUTE or any operation buttons of this
unit to cancel a mute and adjust the volume.
No picture. There is no S-video connection between this
unit and the video monitor, although S-
video signals are being input to this unit.
Connect the monitors S-video input jack to
this units S VIDEO MONITOR OUT jack.
The sound suddenly
goes off.
The protection circuit has been activated
because of a short circuit, etc.
Check the IMPEDANCE SELECTOR switch
is set to the appropriate position and then turn
the unit back on.
Only the speaker on
one side can be heard.
Connect the cables properly. If the problem
persists, the cables may be defective.
Incorrect setting of 3 L/R BALANCE
on the SET MENU.
Adjust it to the appropriate position.
19
16, 17
12 15
24
16, 17
25
24
APPENDIX
The sleep timer has functioned. Turn on the power, and play the source again.
Incorrect cable connections.
Check the speaker wires are not touching
each other and then turn the unit back on.
14, 15
19
16, 17
48
12 17
43
The sound is muted. Press MUTE or any operation buttons of this
unit to cancel a mute and adjust the volume.
25
Digital signals other than PCM audio,
Dolby Digital or DTS signal which this
unit cannot reproduce are being input to
this unit by playing a CD-ROM, etc.
Play a source whose signals this unit can
reproduce.
25
69
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
TROUBLESHOOTING
Problem Cause Remedy
Refer to
page
No sound from the
effect speakers.
The sound effect is off.
Press EFFECT to turn it on.
A Dolby Surround, Dolby Digital or DTS
decoding DSP program is being used with
material not encoded with Dolby Surround,
Dolby Digital or DTS.
Select another DSP program.
A 96-kHz sampling digital signal is being
input to this unit.
No sound from the
center speaker.
The output level of the center speaker is set
to minimum.
Raise the level of the center speaker.
1A CENTER SP on the SET MENU is
set to NONE.
Select the appropriate mode for your center
speaker.
One of the Hi-Fi DSP programs (1 to 5)
has been selected.
Select another DSP program.
The source encoded with a Dolby Digital
or DTS signal does not have a center
channel signal.
No sound from the
rear speakers.
The output level of the rear speakers is set
to minimum.
Raise the output level of the rear speakers.
A monaural source is being played with the
program 10.
Select another DSP program.
No sound from the
subwoofer.
1D LFE/BASS OUT on the SET MENU
is set to SWFR or MAIN when a 2-channel
source is being played.
Select BOTH.
The source does not contain low bass
signals (90 Hz and below).
1D LFE/BASS OUT on the SET MENU
is set to MAIN when a Dolby Digital or
DTS signal is being played.
Select SWFR or BOTH.
Poor bass
reproduction.
1D LFE/BASS OUT on the SET MENU
is set to SWFR or BOTH and your system
does not include a subwoofer.
Select MAIN.
The output mode for each speaker (main,
center or rear) on the SET MENU does not
match your speaker configuration.
Select the appropriate output mode for each
speaker based on the size of the speakers in
your configuration.
29
57 60
25
47
40
57 60
47
57 60
42
42
42
40, 41
12 15
12
A humming sound
can be heard.
Incorrect cable connections.
Firmly connect the audio plugs. If the
problem persists, the cables may be
defective.
No connection from the turntable to the
GND terminal.
Connect the grounding cord of your
turntable to the GND terminal of this unit.
The volume level is
low while playing a
record.
The record is being played on a
turntable with an MC cartridge.
The turntable should be connected to the unit
through an MC-head amplifier.
12, 13
70
TROUBLESHOOTING
Problem Cause Remedy
Refer to
page
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the REC OUT
jacks of this unit is turned off.
Turn on the power to the component.
The sound effect
cannot be recorded.
It is not possible to record the sound effect by
a recording component.
CHECK SP WIRES
appears on the front
panel display.
The sound is degraded
when listening with
headphones
connected to a tape
deck or CD player that
is connected to this
unit.
There is noise
interference from
digital or high-
frequency equipment,
or the unit.
The unit is too close to the digital or high-
frequency equipment.
Move the unit further away from such
equipment.
This unit does not
operate properly.
The internal microcomputer has been frozen
by an external electric shock (such as
lightning or excessive static electricity) or by
a power supply with low voltage.
Disconnect the AC power cord from the
outlet and then plug it in again after about
30 seconds.
A source cannot be
recorded by a digital
recording component
connected to the
DIGITAL OUTPUT jack
of this unit.
A source component is only connected to the
analog input jacks of this unit.
Connect the source component to the digital
input jacks of this unit.
The sound field
parameters and some
other settings on this
unit cannot be
changed.
15 MEMORY GUARD on the SET MENU
is set to ON.
Select OFF.
Speaker cables are short circuited. Make sure all speaker cables are connected
correctly.
This unit is in the standby mode. Turn on the power of the unit.
12
38
12 15
46
16, 17
71
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
TROUBLESHOOTING
Tuner
Problem Cause Remedy
Refer to
page
FM stereo
reception is noisy.
The characteristics of FM stereo broadcasts
may cause this problem when the
transmitter is too far away or the antenna
input is poor.
Check the antenna connections.
Try using a high-quality directional FM
antenna.
Use the manual tuning method.
There is distortion,
and clear reception
cannot be obtained
even with a good
FM antenna.
There is multipath interference.
Adjust the antenna position to eliminate
multipath interference.
The desired station
cannot be tuned in
with the automatic
tuning method.
The station is too weak. Use the manual tuning method.
Use a high-quality directional FM antenna.
Previously preset
stations can no
longer be tuned in.
The unit has been disconnected for a long
period.
Re-store the stations.
The desired station
cannot be tuned in
with the automatic
tuning method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections and
orient it for best reception.
Use the manual tuning method.
There are
continuous
crackling and
hissing noises.
Noises result from lightning, fluorescent
lamps, motors, thermostats and other
electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
There are buzzing
and whining noises
(especially in the
evening).
A TV set is being used nearby. Move this unit away from the TV.
FM
AM
30, 31
30
30, 31
32
30, 31
30
72
TROUBLESHOOTING
Remote control
Problem Cause Remedy
Refer to
page
The remote control
does not work nor
function properly.
Wrong distance or angle.
The remote control will function within a
maximum range of 6 m (20 feet) and no more
than 30 degrees off-axis from the front panel.
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition the unit.
The batteries are weak. Replace all batteries with new ones.
The unit or other
component cannot be
controlled.
The component to be controlled has not been
selected.
Set the selector dial to the appropriate position,
corresponding to the component to be
controlled.
The remote control cannot control system
components.
The manufacturer code has not been set up
properly.
Enter the code again.
Try setting another code for the same
manufacturer.
Depending on the manufacturer or the
model, some components cannot be
controlled with this units remote control
even though the code has been set up
properly.
Program functions from the other remote
controls function into this remote control.
The remote control
does not learn new
functions.
The batteries of this remote control and/or
the other remote control are too weak.
Replace the batteries.
The distance between the two remote
controls is too much or too little.
Place the remote controls at the proper
distance.
The signal coding or modulation of the
other remote control is not compatible with
this remote control.
Learning is not possible.
Memory capacity is full. Further learning is not possible without
deleting unnecessary functions.
8
3
49
54
55
3
55
55
55
After this unit has been exposed to a strong external electric shock (such as lightning and strong static electricity) or if
you mishandle the operation of this unit, it may not function properly. In these cases, set this unit in the standby mode,
disconnect the power cord, plug it back in after 30 seconds, and start operating.
73
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPECIFICATIONS
AUDIO SECTION
Minimum RMS Output Power for Main, Center, Rear
20 Hz to 20 kHz, 0.04% THD, 8 ohms ............................... 100 W
1 kHz, 0.04% THD, 8 ohms ................................................ 105 W
DIN Standard Output Power
1 kHz, 0.7% THD, 4 ohms .................................................. 140 W
IEC Output Power
1 kHz, 0.04%, 8 ohms ......................................................... 105 W
Dynamic Power (IHF)
8/6/4/2 ohms ................................................... 125/160/195/230 W
Damping Factor
20 Hz to 20 kHz, 8 ohms .............................................. 80 or more
Frequency Response
CD to Main L/R ...................................... 10 Hz to 100 kHz, 3 dB
Total Harmonic Distortion
20 Hz to 20 kHz, 50 W, 8 ohms, Main L/R .......................... 0.04%
Signal to Noise Ratio (IHF-A Network)
PHONO MM to REC OUT (5 mV, shorted) ........................ 81 dB
CD (250 mV, shorted) to Main L/R, Effect Off ................. 100 dB
Residual Noise (IHF-A Network)
Main L/R ................................................................ 150 µV or less
Channel Separation (1 kHz/10 kHz)
CD (5.1 kohms terminated) to Main L/R .................. 60 dB/45 dB
Tone Control (Main L/R)
BASS Boost/Cut ...................................................... ±10 dB/50 Hz
TREBLE Boost/Cut ............................................... ±10 dB/20 kHz
BASS EXTENSION ................................................. +6 dB/60 Hz
Phones Output ..................................................... 150 mV/100 ohms
Input Sensitivity
CD, etc .............................................................. 150 mV/47 kohms
PHONO ............................................................. 2.5 mV/47 kohms
6CH INPUT .............................................. 150 mV/40 47 kohms
Output Level
REC OUT ........................................................ 150 mV/0.9 kohms
PRE OUT ............................................................ 2.6 V/1.2 kohms
SUBWOOFER .................................................... 4.0 V/1.2 kohms
VIDEO SECTION
Video Signal Type ...................................................................... PAL
Composite Video Signal Level ................................ 1 Vp-p/75 ohms
S-Video Signal Level
Y ........................................................................... 1 Vp-p/75 ohms
C .................................................................... 0.286 Vp-p/75 ohms
Component Video Signal Level
Y ........................................................................... 1 Vp-p/75 ohms
P
B
/C
B
, P
R
/C
R
....................................................... 0.7 Vp-p/75 ohms
Signal to Noise Ratio ............................................................... 50 dB
Frequency Response (MONITOR OUT)
Composite, S-Video ................................. 5 Hz to 10 MHz, 3 dB
Component ................................................. DC to 30 MHz, 3 dB
FM SECTION
Tuning Range .................................................. 87.50 to 108.00 MHz
50 dB Quieting Sensitivity (IHF, 100% mod.)
Mono/Stereo ........................ 2.0 µV (17.3 dBf) /25 µV (39.2 dBf)
Selectivity (400 kHz) ............................................................... 70 dB
Signal to Noise Ratio (IHF)
Mono/Stereo .............................................................. 76 dB/70 dB
Harmonic Distortion (1 kHz)
Mono/Stereo ................................................................. 0.2%/0.3%
Stereo Separation (1 kHz) ....................................................... 45 dB
Frequency Response ........................... 20 Hz to 15 kHz +0.5, 2 dB
AM SECTION
Tuning Range ......................................................... 531 to 1611 kHz
Usable Sensitivity ............................................................. 300 µV/m
GENERAL
Power Supply ......................................................... AC 230 V/50 Hz
Power Consumption .................................................. approx. 300 W
Standby Mode ......................................................... approx. 1.2 W
AC Outlets (Total 100 W maximum)
[Europe model] ..................................................... 2 (SWITCHED)
[U.K. model] ........................................................ 1 (SWITCHED)
Dimension (W x H x D)
............................ 435 x 171 x 432 mm (17-1/8 x 6-3/4 x 17)
Weight ......................................................................... 15 kg (33 lbs)
Accessories .............................................................. Remote Control
....................................................................................... Batteries
......................................................................... AM loop antenna
...................................................................... Indoor FM antenna
................ 75-ohm/300-ohm antenna adapter (U.K. model only)
................................................................. Quick Reference Card
* Specifications are subject to change without notice.
i
LIST OF MANUFACTURER’S CODES
LISTES DES CODES FABRICANT
VERZEICHNIS DER HERSTELLERCODES
LISTA ÖVER TILLVERKARKODER
ELENCO DEI CODICI DEL FABBRICANTE
LISTA DE CÓDIGOS DE FABRICANTES
LIJST VAN CODES VAN FABRIKANT
TV
ADMIRAL 0411, 0451, 0911,
1021, 1081
AIKO 0891
AKAI 0061, 0101, 0231,
1191, 1351, 1591,
1641, 1791, 1891,
1981
AKURA 1331
ALBA 1241, 1331, 2361
ALBIRAL 1971
AMSTRAD 1301, 1511
ANAM 1171
ARC EN CIEL 0571
ARCAM 0571, 0761
ARISTONA 0751
ARTHUR MARTIN 0451, 1641
ASA 0411, 0451, 0521,
0781, 0871, 1021,
1081, 1421, 2051,
2091, 2151, 2551
ASTRA 1511
ATANTIC 0761
ATLANTIC 0761
ATORI 1511
AUDIOSONIC 1181, 1321, 1511
AUSIND 0491, 1411
AUTOVOX 0091, 0351, 0481,
0491, 0601, 0781,
0951, 1051, 1081,
1391, 1421
BAIRD 1101, 1351
BANG & OLUFSEN 1081
BASIC LINE 1321, 1331
BAUER 1451
BAUR 0041, 0061, 0121,
0131, 0221, 1561
BEKO 2491, 2501
BLAUPUNKT 0221, 0231, 0241,
0251, 0471, 0741,
2201, 2211, 2221,
2231, 2241, 2261,
2571, 2581
BRANDT 0571, 0651, 0731,
0901, 1821
BRIONVEGA 1021, 1051, 1081
BRITANNIA 0761
BRUNS 0821, 0991, 1021,
1081
BSR 0391, 0691, 1621,
1901, 1981
BUSH 0451, 1241, 1331,
1641, 1741, 2131,
2151
BUSH (UK) 0481, 1561, 1611
CANDLE 0791
CENTURY 1021, 1081
CGE 0491, 0811, 0981,
1401, 1531, 1611,
1621, 1981, 2201,
2251, 2271
CITIZEN 0791
CLARIVOX 0821, 0961, 1971
CLATRONIC 1181, 1331
CONCERTO 0791
CONDOR 0761
CONTEC 0151, 1171
CONTINENTAL EDISON
0571, 0651, 0901
CRAIG 1171
CROSLEY 0021, 0491, 1021,
1081, 1401, 1981,
2201, 2251, 2271
CROWN 2541
CTC CLATRONIC 0261
CXC 1171
DAEWOO 0101, 1501, 1511,
2611
DANSAI 0101
DECCA 0271, 0581, 0601,
0971, 1101, 1691
DECCA (UK) 0271, 0581, 0601,
1101, 1681
DEGRAAF 0451, 1351
DIXI 0991, 1511
DOMEOS 0101
DORIC 1031
DUAL 0091, 0601, 1611,
1641, 2101
DUAL-TEC 0601, 1511, 1621,
2111
DUMONT 0261, 0521, 0781,
1021, 1081, 1981,
2121, 2151
DYNATRON 0101
ELBE 1551, 1971, 2031
ELECTRO TECH 1511
ELEKTRONSKA 0771
ELMAN 0261, 1621
ELTA 1511
EMERSON 0921, 1021, 1081,
1121, 1171, 1261,
1301
ERRES 0101
ETRON 1981
EUROPHON 0261, 0581, 0601,
0771, 1091, 1621,
2001
FENNER 0101, 1511
FERGUSON 0281, 0371, 0551,
0651, 0781, 0861,
0881, 1131, 1181,
1361, 1461, 1971,
1991, 2281, 2311,
2341
FIDELITY 0451, 0761, 2281
FIDELITY (UK) 0561, 0591,
1931, 2281
FILMNET 1141
FINLANDIA 0451, 2321
FINLUX 0021, 0261, 0491,
0521, 0781, 0811,
0871, 1081, 1411,
1421, 1981, 2051,
2091, 2121, 2151,
2551
FIRST LINE 1981
FISHER 0021, 0091, 0141,
0511, 0601, 0801,
0821, 0981, 1021,
1081, 1981, 2091
FORGESTONE 2281
FORMENTI 0451, 0491, 0761,
1081, 1451, 1541,
1981
FORMENTI-PHOENIX
0021, 0431, 0451,
0591, 1411
FORTRESS 1081
FRONTECH 0451, 1181, 1981
FUJITSU 1261
FUNAI 0391, 0691, 1171,
1181, 1261
FUTURETECH 1171
GBC 0021, 0141, 1321,
1511, 1621, 1981
GEC 0451, 1101, 1281,
2321
GEC (UK) 0031, 0081, 0581,
0601, 1101, 1281,
1561
GELOSO 0021, 0411, 0451,
1321, 1511, 1621,
1981
GENERAL TECHNIC2681
GENEXXA 0451, 1331
GOLDSTAR 0591, 0601, 0761,
0791, 1371, 1491,
1511, 1561, 1621,
1641
GOODMANS 0141, 1101, 1371,
1641, 2301
GORENJE 0981, 1061
GRAETZ 0451
GRANADA 0141, 0451, 0491,
0581, 0601, 1101,
1111, 1351, 1981,
2321
GRANADA (UK) 0081, 0141,
0451, 0491,
0581, 0601,
1031, 1311,
1521, 1561,
1641
GRUNDIG 0221, 0231, 0471,
0491, 0711, 0741,
1381, 2021, 2041,
2141, 2151
HANSEATIC 0021, 0121, 0141,
0431, 0591, 1561
HANTAREX 0581
HEMMERMANN 0061
HIFIVOX 0331, 0571
HINARI 0071, 0141, 0451,
1261, 1351, 1511,
1641, 1981, 2011
HITACHI 0001, 0011, 0031,
0081, 0141, 0291,
0331, 0341, 0451,
0601, 0631, 0701,
1281, 1561, 1601,
1821, 1831, 1841,
1861, 1871, 1881,
1891, 1941, 1981,
2051, 2321, 2341
HYPER 0591, 0601, 1511,
1621
IMPERIAL 0451, 0491, 0811,
0981, 1401, 1611,
1621, 2201, 2251,
2271
INGERSOL 1511
INNO HIT 0581, 0601, 0841,
1101, 1331, 1371,
1511, 2011
INNOVATION 2591, 2601, 2611,
2621, 2641, 2651,
2661, 2711, 2721,
2761, 2771, 2781
INTERFUNK 0031, 0041, 0061,
0121, 0181, 0451,
0491, 1081, 1641,
1791, 1821, 1981,
2231
IRRADIO 0491, 1321, 1331,
1371, 1411, 1511,
2011
ISUKAI 1331
ITT 0031, 0041, 0051,
0061, 0071, 0081,
0181, 0411, 0451,
0491, 1241, 1291,
1351, 1501, 1601,
1641, 1741, 1921,
1981, 2091, 2331,
2431
ITT-NOKIA 0031, 0041, 0051,
0061, 0071, 0081,
0181, 0411, 0451,
0491, 1241, 1291,
1351, 1501, 1601,
1641, 1741, 1921,
1981, 2091, 2331,
2431
JVC 0071, 0721, 1441,
1581, 1591, 1741,
1791
KAISUI 0591, 1321, 1331
KAMOSONIC 0601
KARCHER 0591, 0601, 0841,
1091, 1321, 1511,
1561, 2051
KAWASHO 0761
KENDO 0261
KENNEDY 0021, 0351, 0951,
1981
KONKA 2701
KORTING 0431, 1011, 1021,
1081, 1541
08V800RDS_code(GB) 8/29/0, 10:00 AM1
ii
KTV 0601, 1171
LENOIR 0601, 1511
LEYEO 1181
LIFETEC 2591, 2601, 2611,
2621, 2641, 2651,
2661, 2671, 2681,
2691, 2711, 2761,
2771, 2781
LOEWE OPTA 0121, 0131, 0581,
0611, 1081
LOGIC 1691, 2281
LOGIK 0551, 1681, 2281
LOWEWE 0831
LUMA 0351, 0451, 1901
LUXMAN 0791
LUXMAN STEREO TUNER
0791
LUXOR 0001, 0061, 0181,
0341, 0421, 0451,
0461, 0491, 0601,
0671, 1351, 1371,
1561, 1601, 1911,
1921, 1981
LYCO 1181
MAGNADYNE 0021, 0061, 0261,
0581, 0641, 0771,
1021, 1081, 1621,
1981
MAGNAFON 0261, 0491, 0581,
0591, 0641, 0761,
1091, 2001
MANESTH 0101
MARANTZ 0101
MARELLI 1081
MARK 0101
MATSUI 0061, 0451, 0601,
0691, 1101, 1151,
1241, 1271, 1301,
1511, 1561, 1681,
1691
MAXIMAL 0071, 1981
MCMICHAEL 1281
MEDION 2591, 2601, 2611,
2621, 2641, 2651,
2661, 2671, 2681,
2691, 2711, 2721,
2761, 2771, 2781
MEMOREX 1511
METZ 0231, 0741, 1001,
1041, 1081, 1481,
2071, 2081
MGA 1231
MICROMAXX 2591, 2621, 2641,
2651, 2711, 2761,
2771, 2781
MINERVA 0221, 0231, 0491,
1381, 2141, 2151
MISTRAL 2281
MITSUBISHI 0141, 0201, 0231,
0661, 1191, 1201,
1231, 1671, 1691,
1741
MIVAR 0491, 0501, 0581,
0591, 0761, 0771,
1371, 1431, 2031
MTC 0791
MULTITECH 0261, 0581, 0601,
0641, 0981, 1321,
1511
MURPHY 0451, 2091
MURPHY (UK) 0081, 1031
N.E.I. 0101, 0961
NAD 1341
NEC 0141, 1711, 1721,
1731
NECKERMANN 0451, 0601,
0981, 1081,
1561, 1931,
1981, 2211,
2231, 2241
NEDIATOR 0101
NICAMAGIC 0761
NIKKAI 1101, 1331, 1641,
1701, 2011
NOBLIKO 0261, 0491, 0591,
0641, 1381, 1411
NOGAMATIC 0571
NOKIA 0031, 0041, 0051,
0061, 0071, 0081,
0181, 0411, 0451,
0491, 1241, 1291,
1351, 1501, 1601,
1641, 1741, 1921,
1981, 2091, 2331,
2431, 2461, 2791
NORDMENDE 0031, 0291, 0331,
0451, 0531, 0541,
0571, 1051, 1131,
1591, 1791, 1811,
1821, 1891, 1941,
2631
OCEANIC 0321, 1651, 1981
OCEANIC (F) 0031, 0061, 0321,
0441, 1661
ONCEAS 0601
ONWA 1171
ORION 0061, 0391, 0691,
0851, 1211, 1241,
1251, 1301, 1481,
1511, 1681, 1691,
1981, 2371, 2421
OSAKA 2011
OSAKI 1101, 1331, 2011
OSUME 0151
OTTO VERSAND 0021, 0121,
0141, 0221,
0601, 1561,
1741, 1981
PAEL 0591, 1411
PANASONIC 0031, 0201, 0211,
0451, 0701, 1311,
1751, 1961, 2561,
2741
PANORAMIC 2351
PATHE MARCONI 0571
PATHE’ CINEMA (F) 0431, 0591,
1621, 1661,
1971
PAUSA 1511
PAUZA 1511
PERDIO 0891, 1101
PHILCO 0021, 0491, 0811,
0981, 1021, 1081,
1401, 1611, 1621,
1751, 2201, 2251,
2271, 2451, 2471
PHILIPS 0101, 0361, 0591,
0621, 0681, 0751,
0761, 1021, 1081,
1281, 2031, 2281,
2291, 2431, 2441,
2511, 2731
PHOENIX 1081
PHONOLA 0751, 1081
PIONEER 0291, 0451, 1341,
1821
PRANDONI-PRINCE 0411, 0451,
0491, 0581,
1411
PRANDONI-PROMCE
0451, 0491, 0581
PRIMA 0451
PROFEX 1981
PROTECH 0641, 1181, 1981
QUELLE 0041, 0061, 0121,
0221, 0231, 0391,
0491, 0521, 0601,
0781, 1371, 1381,
1411, 1421, 1641,
1681, 2051, 2091,
2141, 2151, 2201,
2211, 2231, 2241,
2251, 2271, 2551,
2571, 2581
REDIOMARELLI 0101, 0451,
0661, 0771,
1081
RADIONETTE 0031, 2051, 2091
RADIOLA 2291
RANK 0481, 2151
RBM 2131, 2151
RBM (UK) 0481
REDIFFUSION 0451, 0661, 1641,
1981, 2331
REDIFFUSION (UK) 0061, 0081,
1031
REX 0071, 0101, 0351,
0411, 0451, 0951,
1901, 2061, 2101,
2111
RFT 0991, 2511
ROADSTAR 1321, 1511
ROTEL 0151
SABA 0291, 0331, 0421,
0451, 0531, 0541,
0571, 0581, 0651,
0731, 0931, 1021,
1071, 1081, 1131,
1791, 1811, 1821,
1891, 1941, 2631
SACCS 1971
SAISHO 0451, 0601, 1161,
1241, 1301, 1511,
1671, 1681, 1691
SALORA 0011, 0041, 0061,
0071, 0341, 0451,
0671, 1291, 1351,
1521, 1561, 1601,
1641, 1911, 1921,
1931, 1981, 2321
SAMBERS 0261, 0491, 0581,
0641, 1091, 1371,
1411, 2001
SAMSUNG 0101, 0601, 0841,
0981, 1101, 1181,
1371, 1511, 2011
SANYO 0141, 0151, 0401,
0601, 0801, 0821,
0981, 1021, 1101,
1111, 1291, 1351,
1691, 1741, 2051,
2091, 2551
SBR 0681, 0751, 1281,
2281
SCHAUB LORENZ 0451
SCHNEIDER 0021, 0071, 0091,
0451, 0511, 0591,
0601, 0751, 1321,
1361, 1621, 1641,
2101, 2111, 2291
SCOTT 1171, 1261
SEG 0261, 0601, 0821,
0991
SEI 0641, 0691, 1081,
1301, 1481, 1981
SELECO 0071, 0101, 0351,
0411, 0451, 0951,
1901, 2061, 2101,
2111
SENTRA 1601
SHARP 0141, 0151, 0191,
1761, 1781
SIAREM 0021, 0261, 0581,
0641, 1021, 1081,
1981
SICATEL 1971
SIEMENS 0151, 0221, 0231,
0451, 0741, 2011,
2201, 2211, 2221,
2231, 2241, 2261,
2571, 2581
SILVER 1181
SINGER 0021, 0261, 1021,
1081
SINUDYNE 0021, 0061, 0101,
0261, 0391, 0641,
0691, 0851, 0941,
1021, 1081, 1241,
1301, 1321, 1481,
1631, 1981
SKANTIC 0451
SOLAVOX 0451, 1641, 2011
SONOKO 0101, 1181, 1511
SONY 0141, 0171, 1121,
1681, 1691, 2751
SOUNDESIGN 1171
SSS 1171
STERN 0071, 0101, 0351,
0411, 0451, 0951,
1901, 2061, 2101,
2111
SUNKAI 0691
SUPRA 0791
TANDBERG 0161, 0331, 0611,
1021, 1421, 1771,
1791, 2081
TANDY 0191, 0451, 1331,
1531
TASHIKO 0141
TATUNG 0271, 0581, 0601,
0971, 1101, 1681,
1691
TCM 2621, 2641, 2711,
2761, 2771, 2781
TECHNICS 1311
TECHWOOD 0791
TEKNIKA 1171, 1231, 1261
TELE 1141
TELEAVIA 0571, 0651, 0731,
1821
TELEFUNKEN 0291, 0301, 0311,
0551, 0731, 1131,
1471, 1591, 1791,
1801, 1811, 1821,
1991, 2161, 2171,
2181, 2191, 2201,
2251, 2271, 2521,
2631
TELETECH 1511
TEMPEST 2381, 2391, 2401,
2411
TENSAI 1331, 2091
TEXET 0601
THOMSON 0331, 0481, 0531,
0571, 0631, 0651,
0731, 0901, 1241,
1571, 1591, 1791,
1811, 1821, 1891,
1941, 2531
THORN 0741, 0861, 2091,
2251, 2271, 2281
08V800RDS_code(GB) 8/29/0, 10:00 AM2
iii
THORN-FERGUSON 0281, 0371,
0551, 0651,
0781, 0861,
0881, 1131,
1181, 1361,
1461, 1971,
1991, 2281
TMK 0141, 0791, 1471
TOSHIBA 0141, 0381, 0481,
1221, 1271, 1701,
1741, 1851, 2151,
2801, 2811
TRANS CONTINENS
0451
TRISTAR 2281
TRIUMPH 0481, 0581, 2121
UHER 0431, 0451, 0481,
0491, 0511, 1311,
1541
ULTRAVOX 0021, 0261, 0591,
1021, 1081, 1981
UNIVERSUM 1181, 2051
UNIVOX 1971
VEGAVOX 0811
VEXA 0101, 1511
VICTOR 1441, 1591
VIDEOTON 2481
VORTEC 0101, 0651
VOXSON 0411, 0451, 0491,
1021, 1081
WALTHAM 0451
WATSON 0431, 2201, 2241
WATT RADIO 0021, 0061, 0261,
0591, 0641, 0761,
1091, 1971, 1981,
2001
WEGA 0141, 1081, 1981
WEGA COLOR 1021
WELTBLICK 0101
WESTON 1621
WHITE WESTINGHOUSE
0101, 0261, 0431,
0591, 0761, 1401,
1541
YOKO 0601, 1511
ZANUSSI 0071, 0101, 0351,
0411, 0451, 0951,
1901, 2061, 2101,
2111
ZOPPAS 0451
CABLE TV
CABLETIME 1446, 1456, 1476
CLYDE CABLEVISION
1426
FILMNET 1396, 1436
FRANCE TELECOM 1386
GEC 1426
JERROLD 1416
MOVIE TIME 1466
NSC 1466
PHILIPS 1386
PIONEER 0006
SAMSUNG 1496
SCIENTIFIC ATLANTA
1486, 1506
STARCOM 1416
STS 1466
TANDBERG 1366
TELE 1436
TELE +1 1436
TELESERVICE 1406, 1476
TUDI 1376
UNITED CABLE 1416
ZENITH 1406
SATELLITE TUNER
AKAI 1276
ALBA 0826, 1276
AMSTRAD 0166, 0796, 1016,
1026, 1296
ANKARO 0476
AST 0406
ASTRA 0126
BARCOM 0476
BLAUPUNKT 0966
BMC SATELLITE 0106
BRITISH TELECOM 1276
BUSH 0826
BUSH (UK) 0956
CAMBRIDGE 0196, 1276
CANAL PLUS (FRANCE)
1536
CHAPARRAL 0016, 0696, 1006
COLUMBUS 0616
CONNEXIONS 0306, 0426
DISCUS ELIPSE 0856, 0866
DISKXPRESS 0426, 0476
DRAKE 1516
ECHOSTAR 0226, 0236, 0606,
0626, 0666, 0926,
0996, 1046, 1056,
1066, 1106
ELTA 1286
ELTA SAT 0146
EURODEC 1226, 1236, 1246
FERGUSON 0046, 0176, 0186,
0296, 0846, 0956,
1306
FINLUX 0976
FRACARRO 0026, 0536, 0776
FUBA 0476, 0616, 0636,
1056
GIUCAR RECORD 0206, 0336
GRUNDIG 0176, 0946, 0956,
0966
HIGH PERFORMANCE
0916
HIRSCHMANN 0756, 0966
HITACHI 0446, 0516, 0706,
0946
ICX INTERNATIONAL 0886
ITT 0066, 0126, 0176,
0446, 1156
ITT/NOKIA 0066, 0126, 0176,
0446, 1156
JEEMON 0146
JERROLD 0846, 0986
JOHANSSON 0246
JVC 1276
KATHREIN 0116, 0266, 0276,
0366
KOSMOS 0266
KYOSTAR 1036, 1086
LENG 0246
LIFESAT 1326, 1346, 1356
LUXOR 0126, 0136, 0446,
0466, 0506, 1156
MACAB 0356
MASPRO 0016, 0116, 0256,
0956
MEDION 1326, 1346
METZ 0966
MICROMAXX 1326, 1346
MITSUBISHI 0966
MORGANS 0596
MURATTO 0406
NEC 0286, 0316, 0766,
0786, 0836
NETWORK 0046
NIKKO 1136, 1146
NOKIA 0066, 0126, 0176,
0446, 1156, 1166,
1336
NORSAT 0786
OTTO VERSAND 0966
PACE 0046, 0176, 0296,
0936, 0956, 1306,
1566, 1576
PACE MSS 0946
PACE SKY DIGITAL BOX (UK)
1526
PALCOM 0616, 0686, 0706
PALSAT 0396
PALTEC 0706
PANASONIC 0806, 1306
PANSAT 1076
PHILIPS 0326, 0346, 0476,
0956, 1126, 1186,
1196, 1206, 1216,
1306, 1316
PROSAT 1176
PTT TELECOM 0306, 0896
QUELLE 0966
RADIX 1056
REDIFFUSION 0316, 0786
RFT 1186, 1196, 1206,
1216
SAGEM 1256, 1546
SAKURA 0566, 0816
SALORA 0066, 0126, 0136,
0446, 0456, 0486,
0496, 0576
SAMSUNG 0746, 0756
SAT 0406
SATCOM 0896
SATECO 0646
SECTOR 1266
SEDEA 1096
SENTRA 0416
SIEMENS 0896, 0966
SINTRACK 0906
SKYLAB 0476
SKYSCAN 0876
SONY 0736, 0946
STELLA 0306
STRONG 0156, 0396, 1036,
1086
STV 0636
TANDBERG 1116
TANDY 0916
TANTEC 0616
TATUNG 0516, 0546
TECHNISAT 0086, 0096, 0526,
0556, 1056
TELECOM 0306
TELEMAX 0586
THORN-FERGUSON 0046, 0076,
0176, 0186,
0956
TOSHIBA 0946
TPS (FRANCE) 1546
TRIAD 0406
UNIDEN 0036, 0216, 0676,
0716, 0726
US ELECTRONICS 0886
VORTEC 0756, 1036, 1076
VTECH 0436
WINERSAT 0246
WISI 0056, 0356, 0376,
0386, 0406, 0656,
1056, 1156
WOLSEY 0916
XCOM MULTIMEDIA 1556
XSAT (FRANCE) 1556
ZEHNDER 0266, 0406
ZENDER 0406
VCR
AIWA 0042, 0352, 0432
AKAI 0042, 0422, 0492,
0582, 0612, 0642,
0652, 0762, 0912
ALBA 0002, 0112, 0282,
0332, 0342, 0972
AMSTRAD 0322, 0432, 0452
ANITECH 0002
ANITSCH 1002
ASA 0012, 0052
AUDIOSONIC 0002
BAIRD 0042, 0282, 0492
BANG & OLUFSEN 0042
BAUR 0052, 0062, 0812
BLAUPUNKT 0062, 0092, 0252,
0462, 0672, 0992
BRIONVEGA 0032
BUSH 0002, 0282, 0332,
0342, 0512, 0972
BUSH (UK) 0812
CAPEHART 0112
CGE 0042, 0432, 0762
CRAIG 0072, 0482
CROWN 0112, 0282, 0622
DAEWOO 0112, 0282, 0622
DANSAI 0012
DAYTRON 0112
DECCA 0042, 0052, 0432,
0942
DECCA (UK) 0052
DEGRAAF 0052, 0132, 0432,
0532, 0602
DIXI 0442
DUAL 0042, 0632
DUMONT 0052, 0432, 0532
DYNATECH 0432
DYNATRON 0012
ELBE 0122
ELIN 0072
EMERSON 0012, 0162, 0202,
0432, 0512, 0522
ERRES 0012
FERGUSON 0042, 0712, 0722,
0852, 0902, 1012,
1022, 1082
FIDELITY 0432
FINLANDIA 0052, 0532
FINLUX 0012, 0042, 0052,
0082, 0262, 0382,
0432, 0462, 0492,
0532, 0572, 0602,
0912
FIRST LINE 0002, 0912
FISHER 0162, 0482, 0532,
0542, 0572, 0592
FORMENTI-PHOENIX
0012, 0052
FRONTECH 0112
FUNAI 0432
GBC 0002
GEC (UK) 0022, 0052
GELOSO 0002
GENERAL TECHNIC1172
GOLDSTAR 0012, 0122, 0812,
0952
GOODMANS 0002, 0072, 0282,
0432, 0502
GOODMANS (UK) 0002
GRAETZ 0022, 0042
GRANADA 0052, 0132, 0532,
0572
08V800RDS_code(GB) 8/29/0, 10:00 AM3
iv
GRANADA (UK) 0052, 0092,
0462, 0602,
0812, 0822
GRUNDIG 0052, 0062, 0092,
0232, 0252, 0262,
0752, 0802
HANSEATIC 0052, 0812
HARMAN/KARDON 0122, 0922
HCM 0002
HINARI 0002, 0202, 0412,
0442, 0522
HITACHI 0042, 0172, 0292,
0432, 0602, 0662,
0812, 1022
IMPERIAL 0072, 0432
INGERSOL 0442
INNO HIT 0002, 0052, 0072
INNOVATION 1142, 1162, 1172
INTERFUNK 0022, 0052
IRRADIO 0002, 0012
ITT 0022, 0032, 0042,
0072, 0292, 0492,
0532, 0572, 0762
ITT-NOKIA 0022, 0032, 0042,
0072, 0292, 0492,
0532, 0572, 0762
JENSEN 0042
JVC 0042, 0102, 0142,
0272, 0742, 0762,
0782, 0902
KARCHER 0052, 0072, 0812
KENDO 0492
KENWOOD 0042, 0142, 0572
LIFETEC 1142, 1162, 1172
LLOYD 0432
LOEWE OPTA 0052, 0092, 0152
LOGIK 0002, 0072, 0442
LUMA 0162
LUXOR 0492, 0572, 0812
M ELECTRONIC 0432
MAGNADYNE 0052
MAGNASONIC 0572
MANESTH 0012
MARANTZ 0012, 0052, 0092,
0122, 0502
MARK 0012
MARTA 0012
MATSUI 0012, 0442, 0512,
0522, 0812, 0972
MEDION 1142, 1162, 1172
MEMOREX 0012, 0132, 0432,
0482, 0532, 0572
METZ 0062, 0092, 0932
MGA 0912
MICROMAXX 1142, 1162, 1172
MINERVA 0062, 0092, 0252
MINOLTA 0172, 0602
MITSUBISHI 0052, 0062, 0142,
0912, 0922
MTC 0072, 0432
MULTITECH 0002, 0052, 0062,
0282, 0432
MURPHY 0432
N.E.I. 0012, 0052
NATIONAL 0462
NEC 0042, 0122, 0142
NECKERMANN 0032, 0042,
0052, 0072,
0092, 0202,
0522, 0572,
0762, 0812
NIKKAI 0112
NOBLIKO 0092
NOKIA 0022, 0032, 0042,
0072, 0292, 0492,
0532, 0572, 0762,
1152
NORDMENDE 0042, 0102, 0142,
0192, 0222, 0242,
0392, 0402, 0632,
0732, 0742, 0762,
0782, 0792, 0832,
0842, 0872
OLYMPUS 0462
OPTONICA 0132, 0502
ORION 0162, 0202, 0312,
0442, 0512, 0522,
0982
OSAKA 0432
OSAKI 0002, 0012, 0432
OTTO VERSAND 0052, 0062,
0812
PANASONIC 0022, 0212, 0462,
0672, 0992, 1092,
1102, 1182
PENTAX 0172, 0602
PERDIO 0432
PHILCO 1062
PHILIPS 0052, 0082, 0092,
0152, 0182, 0362,
0372, 0382, 0472,
0502, 1072
PHONOLA 0052, 0152
PILOT 0012
PIONEER 0052, 0142, 0372,
0472
PORTLAND 0112
PROLINE 0432
PYE 0052, 0152
QUARTZ 0572
QUELLE 0012, 0032, 0042,
0052, 0062, 0072,
0092, 0202, 0462,
0522, 0942
RADIONETTE 0022
REALISTIC 0012, 0072, 0132,
0432, 0482, 0502,
0532, 0572
RET 1072
REX 0042, 0742, 0782
RICOH 0952
SABA 0042, 0142, 0192,
0222, 0242, 0392,
0632, 0732, 0742,
0762, 0772, 0782,
0792, 0872
SAISHO 0162, 0202, 0292,
0442, 0512, 0522,
0972
SALORA 0192, 0572, 0812,
0822, 0912
SAMSUNG 0052, 0072, 0622,
0652, 1192
SANSUI 0042, 0142
SANYO 0482, 0532, 0562,
0572
SBR 0052, 0152, 0182
SCHAUB LORENZ 0022, 0042
SCHNEIDER 0002, 0012, 0052,
0072, 0432
SEG 0002, 0072
SEI-SINUDYNE 0442
SELECO 0042
SENTRA 0112
SHARP 0132, 0502, 0702
SHINTOM 0002
SIEMENS 0062, 0092, 0252,
0572
SINUDYNE 0052, 0382, 0442,
0932
SONOKO 0282
SONY 0432, 0552, 0682,
0692, 0942, 0952,
0962, 1122, 1132
STS 0602
SUNKAI 0512
SUNSTAR 0432
SYLVANIA 0432, 0912
SYMPHONIC 0432, 0912
TANDBERG 0062, 0162, 0522,
0932
TASHIKO 0132, 0432
TATUNG 0042, 0052, 0432,
0922
TCM 1142, 1162, 1172
TEAC 0042, 0432
TECHNICS 0462
TEKNIKA 0012, 0432
TELEFUNKEN 0042, 0192, 0632,
0732, 0742, 0762,
0782, 0882, 0892
TEMPEST 1032, 1042, 1052
TENOSAL 0002
THOMSON 0042, 0102, 0142,
0192, 0402, 0632,
0762
THORN 0042, 0902
THORN-FERGUSON 0042, 0222,
0302, 0712,
0722, 0742,
0762, 0852,
0862, 0872,
0902
TMK 0522
TONSAI 0002
TOSHIBA 0042, 0622, 0912
TOTEVISION 0012, 0072
TRIUMPH 0922
UHER 0042, 0072
ULTRAVOX 0032
UNITECH 0072
VECTOR RESEARCH
0122
VICTOR 0042, 0102, 0142
VIDEON 1162, 1172
WELTBLICK 0012
WHITE WESTINGHOUSE
0032
XENON 0162
YAMAHA 0042, 1202
YOKO 0012, 0062, 0072
DVD PLAYER
AKAI 0108
JVC 0168, 0348
KENWOOD 0288
MAGNAVOX 0248
MITSUBISHI 0268
ONKYO 0128, 0248
PANASONIC 0048
PHILIPS 0188, 0248
PIONEER 0208, 0228
PROSCAN 0308
RCA 0308
SAMSUNG 0148
SHARP 0068
SONY 0028
TECHNICS 0048
THOMSON 0328
TOSHIBA 0088, 0248
YAMAHA 0008, 0048
ZENITH 0248
LD PLAYER
AIWA 0137
FUNAI 0137
HITACHI 0047
MAGNAVOX 0077
PANASONIC 0027
PIONEER 0037
RCA 0067
REALISTIC 0137
SAMSUNG 0017, 0087
SONY 0057, 0097, 0107,
0117
VICTOR 0127
YAMAHA 0007
CD PLAYER
ACCUPHASE 0315
ADC 0865
ADCOM 0785, 1015
AKAI 0115, 0125, 0725,
0735, 0745, 0935,
1155
ARCAM 1875
ARCAM-ROTEL 0165
AUDIO-TECHNICA 0835
AUDIOSONIC 0155
AIWA 1105, 1235, 1245,
1765, 1915, 1935
BSR 0875
CALIFORNIA AUDIO LAB
1075
CARRERA 0555, 0875
CARVER 0825, 1415
CYRUS-ROTEL 0205
DENON 0045, 0955, 1045,
1595, 1795, 1805
DUAL 1005
ELIN 0185
EMERSON 1015, 1285, 1675
FISHER 0105, 0595, 0605,
0825, 1165, 1175
GENEXXA 0525, 0825, 0855,
0875, 0995, 1265,
1285, 1345, 1355,
1485, 1575, 1675,
1715, 1825
GOLDSTAR 0555, 1185, 1195,
1585
GRUNDIG 0175
HARMAN KARDON 0325, 0495,
0565, 1135,
1145, 1155
HITACHI 0065, 0585, 0685,
0945, 1005, 1015,
1225, 1545
INNOVATION 1995, 2005, 2015
ITT-NOKIA 0185
JVC 0385, 0395, 0455,
0575, 0585
KARCHER 0485
KENWOOD 0025, 0055, 0145,
0215, 0595, 0675,
0695, 0705, 0715,
0925, 1355, 1485,
1575, 1675, 1715,
1825
KORTING 0175
LIFETEC 2015
LIGHT CONTROL 1155, 1645,
1655, 1665
LINN 0165, 1875
LUXMAN 0265, 0275, 0795,
0805, 1295, 1305,
1555, 1925
08V800RDS_code(GB) 8/29/0, 10:00 AM4
v
LUXOR 0185, 1895, 1905
MAGNAVOX 1865, 1875
MARANTZ 0165, 0175, 0545,
0665, 1275, 1335,
1405, 1505, 1875,
1955
MATSUSHITA 1095, 1605
MCS 0535
MEDION 0075, 1995, 2005,
2015
MEMOREX 0525, 1015, 1265,
1275, 1285, 1675
MGA 1125
MICROMAXX 2015
MISSION 0165, 1875
MITSUBISHI 1125, 1205
NAD 0135, 0255, 0285,
0295, 0305, 0345,
0755, 0765, 1315,
1325
NAKAMICHI 0635, 0645, 1565
NEC 0405, 0535, 0775,
0785
NECKERMAN 0155, 0225
NIKKO 0835, 1165
OCEANIC 0185
OKANO 0155, 0225
ONKYO 0885, 1385, 1425,
1455, 1515
PANASONIC 1055, 1075, 1615,
1625
PHILIPS 0165, 0175, 0195,
1865, 1875
PIONEER 0095, 0335, 0425,
0435, 0445, 0525,
0855, 1035, 1945
PROTON 0905, 1875
QUASAR 1075
RADIOLA 1845, 1855
RADIOTONE 0485
REALISTIC 0825, 1015, 1265,
1275, 1285, 1575
ROTEL 1875
SABA 1005
SAE 1875
SALORA 0185
SANSUI 0415, 0965, 0975,
0985, 1255, 1675,
1875
SANYO 0625, 0825, 0845,
0915
SCHNEIDER 1845, 1855
SCOTT 1285, 1675
SHARP 0025, 0035, 1025,
1115, 1275, 1635,
1785, 1815, 1825,
1835
SHERWOOD 1275, 1445
SIEMENS 1085
SIGNATURE 1155
SONY 0345, 0355, 0365,
0375, 0865, 1685,
1695, 1705, 1715,
1725, 1735, 1745
SYLVANIA 1875
TANDBERG 1885
TASHIKO 1525
TCM 1985, 2015
TEAC 0235, 0245, 1275,
1365, 1375, 1395,
1435, 1465, 1475
TECHNICS 0465, 0475, 1065,
1075, 1625
TELEFUNKEN 1005
THETA DIGITAL 1865
THOMSON 1005
TOSHIBA 0755, 0765
VECTOR RESEARCH
0555, 0865
VICTOR 0575
YAMAHA 0005, 0015, 1815,
0085, 0345, 0615,
0655, 0815, 0835,
0895
CD RECORDER
YAMAHA 0244
MD RECORDER
YAMAHA 0024, 0224, 0234
KENWOOD 0214
SONY 0224
TAPE DECK
AKAI 0124
DENON 0204
GRUNDIG 0134
HARMAN 0044
JVC 0194
KENWOOD 0164
KORTING 0134
LUXMAN 0054, 0064, 0074,
0084
MARANTZ 0134, 0144
NAD 0174
ONKYO 0184
PHILIPS 0134, 0144, 0154
PIONEER 0034, 0114
SONY 0094, 0104
YAMAHA 0004, 0014
08V800RDS_code(GB) 8/29/0, 10:00 AM5
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia ID
V624940-2
RX-V800RDS
Natural Sound AV Receiver
Ampli-tuner audio-vidéo
G B
RX-V800RDS
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
0100V800RDS(GB)-cv1/4 10/3/0, 9:14 AM1
u/d
Numeric buttons (MD/CD-R)
Quick Reference Card
TAPE/MD (CD-R)
AMP/TUN
DSP/TUN
INPUT
p Play
r Rec/Pause
(tape/MD)
DSP
b DIR A (tape)
Skip – (MD/CD-R)
w Rewind (tape)
Search (MD/CD-R)
Numeric buttons
p Play
DISC SKIP –/+
DSP
CD
b Skip –
w Search
INDEX
INPUT
+10
DISPLAY
e Pause
a Skip +
s Stop
f Search
AV POWER
PRESET –/+
DSP
DSP
A/B/C/D/E
j / i
Input
selector
buttons
DSP
program
group
buttons
EFFECT
INPUT
DSP
program
group
buttons
EFFECT
6.1/ES
6.1/ES
INPUT
SET MENU
STANDBY
TEST
Input
selector
buttons
LEVEL
ON SCREEN
TV POWER
TV VOLUME
TV INPUT
POWER
VOLUME +/–
SLEEP
MUTE
V624990-1
+10 (MD/CD-R)
Deck A/B (tape)
DISPLAY (MD/CD-R)
e Pause (MD/CD-R)
a DIR B (tape)
Skip + (MD/CD-R)
s Stop
f Fast
forward (tape)
Search (MD/CD-R)
AV POWER
INDEX (CD-R)
A/B/C/D/E
A/B/C/D/E
A/B/C/D/E
Quick Reference Card
Press this button twice to start recording.
Appuyer deux fois sur cette touche pour commencer l’enregistrement.
Drücken Sie diese Taste zweimal, um die Aufnahme zu starten.
Tryck två gånger på den här knappen för att börja spela in.
V624990-1
*1 Premere due volte questo tasto per iniziare la registrazione.
Presione dos veces este botón para empezar a grabar.
Druk tweemaal op deze toets om met opnemen te beginnen.
DISC SKIP –/+ (DVD)
DSP
DVD/LD DVD MENU
CBL/SAT
TV
VCR
INDEX/Time (DVD)
Chapter/Time (LD)
INPUT
Numeric buttons
Numeric
buttons
Numeric
buttons
+10
DISPLAY
e Pause
a Skip + (DVD)
Skip/Chapter + (LD)
s Stop
f Search
AV POWER
AV POWER
Numeric
buttons
AV POWER
Numeric buttons
AV POWER
p Play
b Skip – (DVD)
Skip/Chapter – (LD)
w Search
DISC SKIP –/+
Return
DSP
INDEX
+10
INPUT
DISPLAY
Menu up
Menu right
Menu down
MENU
Menu select
Menu left
TITLE
Ch enter/
Recall
INPUT
DISPLAY
_/_ _
e Pause
s Stop
f Fast
forward
p Play
w Rewind
TV INPUT
TV VOL +/–
TV
POWER
CH –/+
DSP
Ch enter/
Recall
_/_ _
INPUT
DISPLAY
VCR pause
VCR stop
VCR fast
forward
VCR power
TV SLEEP
TV MUTE
VCR play
VCR REC
VCR rewind
CH –/+
DSP
VCR REC
CH –/+
DSP
Ch enter
INPUT
_/_ _
DISPLAY/
Guide
(SAT)
Menu up
Menu
right
Menu
down
MENU
Menu
select
Menu left
Recall
*1
*1
A/B/C/D/E
A/B/C/D/E
A/B/C/D/E
A/B/C/D/E
A/B/C/D/E

Documenttranscriptie

GB RX-V800RDS YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA 0100V800RDS(GB)-cv1/4 1 RX-V800RDS Natural Sound AV Receiver Ampli-tuner audio-vidéo OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING Printed in Malaysia ID V624940 8/29/0, 10:02 AM CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this unit in a well ventilated, cool, dry, clean place with at least 30 cm on the top, 20 cm on the right and left, and 10 cm at the back of this unit — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid. 4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. 5 On the top of this unit, do not place: – Other components, as they may cause damage and/or discoloration on the surface of this unit. – Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. – Containers with liquid in them, as they may cause electrical shock to the user and/or damage to this unit. 6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. 7 Do not plug in this unit to a wall outlet until all connections are complete. 8 Do not operate this unit upside-down. It may overheat, possibly causing damage. 9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord. 15 Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons. 16 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. 17 Be sure to read the “TROUBLESHOOTING” section on common operating errors before concluding that this unit is faulty. 18 Before moving this unit, press STANDBY/ON to set this unit in the standby mode, and disconnect the AC power plug from the wall outlet. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. ■ For U.K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note • The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. ■ Special Instructions for U.K. Model IMPORTANT THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: 11 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Blue: NEUTRAL Brown: LIVE 12 Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. 13 To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm. 14 Take care of this unit so that no foreign objects and/ or liquid drops inside this unit. II CAUTION II INTRODUCTION CONTENTS CONTENTS ........................................................... 1 FEATURES ............................................................ 2 GETTING STARTED ........................................... 3 Checking the Package Contents ............................... 3 Installing Batteries in the Remote Control ............... 3 CONTROLS AND FUNCTIONS ........................ 4 PREPARATION SPEAKER SETUP .............................................. 11 CONNECTIONS ................................................. 12 Before Connecting Components ............................ 12 Connecting Audio Components ............................. 12 Connecting Video Components .............................. 14 Connecting the Speakers ........................................ 16 Connecting to an External Amplifier ..................... 18 Connecting an External Decoder ............................ 18 IMPEDANCE SELECTOR Switch ....................... 19 Connecting the Power Supply Cords ...................... 19 OSD Modes ............................................................ 20 Selecting the OSD Mode ........................................ 20 SPEAKER MODE SETTINGS ......................... 21 Summary of SPEAKER SET Items 1A through 1E .................................................... 21 ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS ...................................................... 47 SLEEP TIMER .................................................... 48 Setting the Sleep Timer .......................................... 48 Canceling the Sleep Timer ..................................... 48 REMOTE CONTROL FEATURES .................. 49 Selector Dial ........................................................... 49 Commonly Used Buttons in Any Position of the Selector Dial ....................................................... 50 Controlling the Components Connected to This Unit ...................................... 50 Button Names and Functions in Each Position ...... 51 Setting the Manufacturer Code .............................. 54 Programming a New Remote Control Function (Learn Feature) ................................................... 55 Returning to the Factory Setting ............................ 56 ADVANCED OPERATION ON-SCREEN DISPLAY (OSD) ......................... 20 Adjusting the Items on the SET MENU ................. 39 1 SPEAKER SET (speaker mode settings) ........... 40 2 LOW FRQ TEST ............................................... 42 3 L/R BALANCE (balance of the left and right main speakers) .............................. 43 4 HP TONE CTRL (headphone tone control) ....... 43 5 CENTER GEQ (center graphic equalizer) ......... 43 6 INPUT RENAME .............................................. 44 7 I/O ASSIGNMENT ............................................ 44 8 INPUT MODE (initial input mode) ................... 44 9 PARAM. INI (parameter initialization) ............. 44 10 DOLBY D. SET (Dolby Digital set) ............... 45 11 DTS LFE LEVEL ............................................ 45 12 6.1/ES AUTO ................................................... 45 13 SP DELAY TIME ............................................ 46 14 DISPLAY SET ................................................. 46 15 MEMORY GUARD ......................................... 46 BASIC OPERATION Speakers to Be Used ............................................... 11 Speaker Placement ................................................. 11 SET MENU .......................................................... 39 PREPARATION Front Panel ............................................................... 4 Remote Control ........................................................ 6 Description of the Numeric Buttons ......................... 7 Using the Remote Control ........................................ 8 Front Panel Display .................................................. 9 Rear Panel .............................................................. 10 ADVANCED OPERATION INTRODUCTION INTRODUCTION ADJUSTING THE SPEAKER OUTPUT LEVELS ......................................... 22 BASIC OPERATION BASIC PLAYBACK ............................................ 24 Input Modes and Indications .................................. 26 Selecting a Sound Field Program ........................... 28 Normal Stereo Reproduction .................................. 29 TUNING ............................................................... 30 RECEIVING RDS STATIONS .......................... 35 Hi-Fi DSP Programs ............................................... 57 CINEMA DSP Programs ....................................... 58 MOVIE THEATER Programs ................................ 61 SOUND FIELD PROGRAM PARAMETER EDITING ......................................................... 62 What is a sound field? ............................................ 62 Sound Field Program Parameters ........................... 62 Changing Parameter Settings ................................. 63 Resetting a Parameter to the Factory-set Value ...... 63 Digital Sound Field Parameter Descriptions .......... 64 APPENDIX TROUBLESHOOTING ...................................... 68 SPECIFICATIONS ............................................. 73 English Description of RDS Data ........................................ 35 Changing the RDS Mode ....................................... 35 PTY SEEK Function .............................................. 36 EON Function ........................................................ 37 SOUND FIELD PROGRAM ............................. 57 APPENDIX Connecting the Antennas ........................................ 30 Automatic (or Manual) Tuning .............................. 31 Presetting Stations .................................................. 32 Tuning in to a Preset Station .................................. 33 Exchanging Preset Stations .................................... 34 ADDITIONAL INFORMATION ADDITIONAL INFORMATION Before You Begin ................................................... 22 Using the Test Tone (TEST DOLBY SUR.) .......... 22 BASIC RECORDING ......................................... 38 1 Thank you for selecting this YAMAHA AV receiver. FEATURES Built-in 5-Channel Power Amplifier Other Features ◆ Minimum RMS Output Power (0.04% THD, 20 Hz – 20 kHz) Main: 100 W + 100 W (8 Ω) Center: 100 W (8 Ω) Rear: 100 W + 100 W (8 Ω) ◆ 96-kHz/24-bit D/A Converter ◆ “SET MENU” which Provides You with 15 Items for Optimizing This Unit for Your Audio/Video System ◆ Test Tone Generator for Easier Speaker Balance Adjustment ◆ 6-Channel External Decoder Input for Other Future Formats ◆ BASS EXTENSION Button for Reinforcing Bass Response ◆ On Screen Display Function Helpful in Controlling This Unit ◆ S Video Signal Input/Output Capability ◆ Component Video Input/Output Capability ◆ Optical and Coaxial Digital Audio Signal Jacks ◆ Sleep Timer ◆ Remote Control with Preset Manufacturer Codes and “Learning” Capability Multi-Mode Digital Sound Field Processing ◆ ◆ ◆ ◆ ◆ Digital Sound Field Processor (DSP) Dolby Pro Logic Decoder Dolby Digital/Dolby Digital Matrix 6.1 Decoder DTS/DTS ES Decoder CINEMA DSP: Combination of YAMAHA DSP Technology and Dolby Pro Logic, Dolby Digital or DTS ◆ Virtual CINEMA DSP ◆ SILENT CINEMA DSP Sophisticated AM/FM Tuner ◆ 40-Station Random Access Preset Tuning ◆ Automatic Preset Tuning ◆ Preset Station Shifting Capability (Preset Editing) ◆ Multi-Functions for RDS Broadcast Reception • y indicates a tip for your operation. • Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this manual. Manufactured under license from Dolby Laboratories. “Dolby”, “AC-3”, “Pro Logic”, “Surround EX” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, Inc. All rights reserved. 2 Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issued and pending. “DTS”, “DTS Digital Surround” and “DTS ES” are trademarks of Digital Theater Systems, Inc. Copyright 1996 Digital Theater Systems, Inc. All Rights Reserved. GETTING STARTED INTRODUCTION Checking the Package Contents Check your package to make sure it has the following items. Remote control AM loop antenna Indoor FM antenna Quick Reference Card PREPARATION Manganese batteries (4) (AAA, R03, UM-4) Quick Reference Card A/B/C/D/E BASIC OPERAIONT 75-ohm/300-ohm antenna adapter (U.K. model only) Insert the batteries in the correct direction by aligning the + and – marks on the batteries with the polarity markings (+ and –) inside the battery compartment. 3 If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the manufacturer code and program any acquired functions that may have been cleared. Note • If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. APPENDIX ■ Notes on batteries As the batteries lose power, the operating range of the remote control decreases and the indicator does not flash or its light becomes dim. When you notice any of these conditions, change all of the batteries. ADDITIONAL INFORMATION 2 1 ■ Changing batteries ADVANCED OPERATION Installing Batteries in the Remote Control • Change the batteries periodically. • Do not use old batteries together with new ones. • Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. English 3 CONTROLS AND FUNCTIONS Front Panel 1 3 2 4 5 6 INPUT VOLUME 7 6CH INPUT INPUT MODE D I G I T A L D I G I TA L SURROUND STANDBY /ON A/B/C/D/E PRESET/ TUNING PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK BASS TREBLE TUNER SPEAKERS A B BASS PROCESSOR EXTENSION DIRECT EDIT PHONES EFFECT ON OFF MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO MODE START L AUDIO R OPTICAL PROGRAM DSP – SILENT PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EDIT 8 9 0 qw e r ty + – u EON MAN'L/AUTO FM AUTO/MAN'L MONO i PTY SEEK MODE START opa s df 1 STANDBY/ON 6 VOLUME Turns on and sets this unit in the standby mode. When you turn on this unit, you will hear a click and there will be a 4 to 5-second delay before this unit can reproduce sound. Controls the output level of all audio channels. This does not affect the REC OUT level. Standby mode In this mode, this unit consumes a small amount of power to receive infrared-signals from the remote control. 2 Remote control sensor + VIDEO AUX gh 7 6CH INPUT Selects the source connected to the 6CH INPUT jacks. The source selected by pressing 6CH INPUT takes priority over the source selected with INPUT l / h (or the input selector buttons). 8 SPEAKERS A/B Receives signals from the remote control. Turn on or off the set of main speakers connected to the A and/or B terminals on the rear panel. 3 Front panel display 9 BASS EXTENSION ON/OFF Shows information about the operational status of this unit (see page 9). When pushed in (ON), this feature boosts the bass frequency of the left and right main channels by +6 dB (60 Hz) while maintaining overall tonal balance. This boost is useful if you do not use a subwoofer. However, this boost may not be noticeable if “1B MAIN SP” on the SET MENU is set to SMALL and “1D LFE/ BASS OUT” is set to SWFR. 4 INPUT MODE Selects the mode of input for sources that send two or more types of signals to this unit (see page 26). You cannot control the input mode when you select 6CH INPUT as the input source. 5 INPUT l / h Selects the input source (DVD, D-TV/LD, CBL/SAT, VCR 1, VCR 2/DVR, V-AUX, PHONO, CD, TUNER, CD-R, MD/TAPE) you want to listen to or watch. 4 0 PROCESSOR DIRECT ON/OFF When pushed in (ON), BASS, TREBLE, and BASS EXTENSION are bypassed, eliminating any alteration of the original signal. CONTROLS AND FUNCTIONS a RDS MODE/FREQ Switches the effect speakers (center and rear) on and off. If you turn off the output of these speakers by using EFFECT, all Dolby Digital and DTS audio signals except for the LFE channel are directed to the main left and right channels. When Dolby Digital or DTS signals are mixed, the left and right main channel signal levels may not match. When an RDS station is received, press this button to change the display mode among the PS mode, PTY mode, RT mode, CT mode (if the station offers those RDS data services) and/or frequency display mode in turn. w A/B/C/D/E Selects one of the 5 preset station groups (A to E). e PROGRAM l / h r PRESET/TUNING l / h Selects preset station number 1 to 8 when the colon (:) appears next to the band indication on the front panel display, and selects the tuning frequency when the colon (:) does not appear. t PHONES jack y VIDEO AUX jacks Inputs audio and video signals from a portable external source such as a game console. To reproduce source signals from these jacks, select V-AUX as the input source. Switches the function of PRESET/TUNING l / h (the colon (:) turns on or off) between selecting a preset station number and tuning. This button is also used to exchange the assignment of two preset stations with each other. Switches the reception band between FM and AM. f PTY SEEK START Press this button to begin searching for a station after the desired program type has been selected in the PTY SEEK mode. g BASS Adjusts the low-frequency response for the left and right main channels. Turn the control to the right to increase or to the left to decrease the low-frequency response. h TREBLE Adjusts the high-frequency response for the left and right main channels. Turn the control to the right to increase or to the left to decrease the high-frequency response. Note • If you increase or decrease the high-frequency or the lowfrequency sound to an extreme level, the tonal quality from the center and rear speakers may not match that of the left and right main speakers. ■ Opening and closing the front panel door When you are not operating the controls behind the front panel door, close the door. o MEMORY (MAN’L/AUTO FM) Stores a station in the memory. Hold down this button for more than 3 seconds to start automatic preset tuning. p TUNING MODE (AUTO/MAN’L MONO) D I G I T A L APPENDIX Switches the tuning mode between automatic and manual. To select the automatic tuning mode, press this button so that the “AUTO” indicator lights up on the front panel display. To select the manual tuning mode, press this button so that the “AUTO” indicator does not light up. ADDITIONAL INFORMATION i FM/AM Press this button to set the unit in the PTY SEEK mode. ADVANCED OPERATION u PRESET/TUNING (EDIT) d PTY SEEK MODE BASIC OPERAIONT Outputs audio signals for private listening with headphones. When you connect headphones, no signals are output to the OUTPUT jacks or to the speakers. Press this button to select the desired program type (NEWS, INFO, AFFAIRS, SPORT) when you want to tune in to a radio program of that type automatically. PREPARATION Selects the DSP program (see page 28). s EON INTRODUCTION q EFFECT To open, press gently on the lower part of the panel. English 5 CONTROLS AND FUNCTIONS Remote Control This section describes the basic operation of this unit with the remote control. First, set the selector dial to the AMP/ TUN position. See “REMOTE CONTROL FEATURES” on pages 49 to 56 for full details. 3 Numeric buttons (Input selector buttons) These buttons select the input source. See pages 7 and 8 for the numeric buttons. 4 TEST Outputs the test tone. 1 2 9 0 Select the AMP/TUN position. q 5 ON SCREEN Selects the on-screen display (OSD) mode for your video monitor. 6 j/i Adjust DSP program parameters and SET MENU items. 7 LEVEL Selects the effect speaker channel (center, rear and subwoofer) so you can adjust their output level independently. 8 SLEEP 3 Sets the sleep timer. 9 INPUT EFFECT See page 7. Switches the function of the numeric buttons to the input selector (see page 7). 0 Indicator 4 5 6 7 w A/B/C/D/E Flashes while the remote control is sending signals. q Selector dial e r Turn this dial to select the position for the component to be controlled. (The proper code must be set up for your component. See “Setting the Manufacture Codes” on page 54.) When the position is selected, the remote control is set to that component operation mode. w A/B/C/D/E, PRESET–/+ TV POWER t y TV VOLUME u These buttons are used to select a preset station. A/B/C/D/E: To select one of 5 preset station groups (A to E) PRESET –/+: To select a preset station number (1 to 8) e u/d 8 Select DSP program parameters and SET MENU items. TV INPUT i r SET MENU Enters the SET MENU. t POWER Turns on the power of this unit. 1 DSP Switches the function of the numeric buttons to the DSP program selector (see page 7). 2 Indicator window Shows the name of components which can be controlled. 6 y STANDBY Sets this unit in the standby mode. CONTROLS AND FUNCTIONS u VOLUME +/– Increases or decreases the volume level. i MUTE ■ When selecting a DSP program and turning on or off the effect speakers (center and rear) A INTRODUCTION Mutes the sound. Press again to restore the audio output to the previous volume level. B EFFECT Switches the effect speakers (center and rear) on and off in the following cases: • When the selector dial is set to the DSP/TUN position. • While the indicator is lit for about 3 seconds after pressing DSP. PREPARATION Description of the Numeric Buttons The numeric buttons function in various ways depending on the position of the selector dial or the combination of other instructions. Press INPUT regardless of the position of the selector dial. The indicator lights up for about 3 seconds. 2 You can select an input source with the numeric buttons while the indicator is lit. Press DSP regardless of the position of the selector dial. The indicator lights up for about 3 seconds. 2 You can select a DSP program with the numeric buttons, turn on or off the effect speakers (center and rear) by pressing EFFECT and turn on or off the Dolby Digital Matrix 6.1 or DTS ES decoder by pressing 6.1/ES while the indicator is lit. B 1 Set the selector dial to the DSP/TUN position. 2 You can select a DSP program directly with the numeric buttons, turn on or off the effect speakers (center and rear) by pressing EFFECT and turn on or off the Dolby Digital Matrix 6.1 or DTS ES decoder by pressing 6.1/ES. ADDITIONAL INFORMATION 1 1 ADVANCED OPERATION Input selector buttons A BASIC OPERAIONT ■ When selecting an input source DSP program group buttons APPENDIX English 7 CONTROLS AND FUNCTIONS ■ When selecting a preset station number Using the Remote Control D I G I TA L D I G I TA L SURROUND STANDBY /ON TUNER DSP – 30° 1 Set code number “0023” in the AMP/TUN (or DSP/TUN) position. See page 54 for setting the code. 2 Set the selector dial to the AMP/TUN (or DSP/TUN) position. 3 You can select a preset station number directly with the numeric buttons (1 to 8). See page 34. 8 30° + – + Approximately 6 m (20 feet) The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation. ■ Handling the remote control • Do not spill water or other liquids on the remote control. • Do not drop the remote control. • Do not leave or store the remote control in the following types of conditions: – high humidity or temperature such as near a heater, stove or bath; – dusty places; or – in places subject to extremely low temperatures. CONTROLS AND FUNCTIONS Front Panel Display 2 34 VIRTUAL e r 6 78 PS PTY 90q RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED t y w VOLUME dB ms u i op D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO a q VOLUME level indicator Lights up when the built-in DTS decoder is on. Indicates the volume level. 2 VIRTUAL indicator w Input source indicator Lights up when using Virtual CINEMA DSP (see page 29). Shows the current input source with the arrow-shaped cursor. 3 g and o indicators e c indicator Light up according to the type of Dolby signals this unit is reproducing. “ g ” lights up when the builtin Dolby Digital decoder is on. “ o ” lights up when the built-in Dolby Pro Logic decoder is on. Lights up when the built-in Dolby Digital Matrix 6.1 or DTS ES decoder is on. r v indicator t SP A/B indicator 5 DSP program indicators Lights up according to which set of main speakers is selected. Both indicators light up when both sets of speakers are selected. Lights up while searching for stations in the PTY SEEK mode. 7 RDS mode indicators 8 EON indicator Lights up when headphones are connected. u Multi-information display Shows the current DSP program name and other information when adjusting or changing settings. i MEMORY indicator Flashes to show a station can be stored. o Program type name indicators The name of the selected program type lights up when the “EON” indicator lights up. Lights up when an RDS station that offers the EON data service is being received. p TUNED indicator 9 STEREO indicator a SLEEP indicator Lights up when the unit is receiving a strong signal for an FM stereo broadcast while the “AUTO” indicator is lit. Lights up while the sleep timer is on. Lights up when this unit tunes in to a station. APPENDIX The name(s) of the RDS data offered by the currently received RDS station light(s) up. Illumination of the red indicator next to the RDS data name shows that the corresponding RDS mode is now selected. ADDITIONAL INFORMATION 6 PTY HOLD indicator y Headphones indicator ADVANCED OPERATION Lights up when this unit is reproducing PCM (pulse code modulation) digital audio signals. Lights up when you select a DSP program. The name of the selected DSP program lights up when the ENTERTAINMENT, MOVIE THEATER 1, MOVIE THEATER 2 or q/DTS SURROUND DSP program is selected. BASIC OPERAIONT 1 t indicator 4 x indicator PREPARATION DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB 5 INTRODUCTION 1 English 0 AUTO indicator Shows that this unit is in the automatic tuning mode. 9 CONTROLS AND FUNCTIONS Rear Panel 1 2 3 DIGITAL OUTPUT MD/ TAPE TUNER 5 4 AUDIO R AUDIO L R IN (PLAY) CD-R OPTICAL AM ANT OUT (REC) GND 75 VIDEO VIDEO COMPONENT DVD DVD Y D-TV /LD PB/ CB CBL /SAT PR/ CR Y VCR 1 CD PHONO OUT PB/ CB IN PR/ CR VCR 2 /DVR OPTICAL COAXIAL – SPEAKERS – MAIN SWITCHED 100W MAX. TOTAL MAIN L B CENTER + SUB WOOFER – IMPEDANCE SELECTOR SET BEFORE POWER ON CENTER + – – + MAIN A OR B: 4 MIN. /SPEAKER A + B: 8 MIN. /SPEAKER CENTER : 6 MIN. /SPEAKER : 6 MIN. /SPEAKER REAR L PB/ CB PR/ CR MONITOR OUT CENTER As this terminal is used for an examination in the factory, do not connect any equipment to this terminal. L MONITOR OUT Y OUT SURROUND DIGITAL INPUT AC OUTLETS OUTPUT + MAIN R CBL /SAT 9 D-TV/LD IN D-TV /LD CD + A R UNBAL. CD-R OUT (REC) DVD GND 8 MAINS R IN (PLAY) FM ANT 7 MD/TAPE CD CD-R S VIDEO L 6 SUB WOOFER S VIDEO REAR (SURROUND) MAIN A OR B: 8 MIN. /SPEAKER A + B:16 MIN. /SPEAKER : 8 MIN. /SPEAKER : 8 MIN. /SPEAKER CENTER REAR R REAR (SURROUND) L VIDEO 6CH INPUT (Europe model) q 0 1 DIGITAL INPUT jacks 8 AC power cord 2 DIGITAL OUTPUT jacks Connect to a power outlet. 3 Antenna input terminals 9 AC OUTLET(S) See page 30 for connection information. Use these outlets to supply power to your other A/V components (see page 19). 4 Audio component jacks 0 6CH INPUT jacks See pages 12 and 13 for connection information. 5 Video component jacks See pages 14 and 15 for connection information. 6 Speaker terminals See pages 16 and 17 for connection information. 7 OUTPUT jacks See page 18 for connection information. 10 See pages 13 and 18 for connection information. q IMPEDANCE SELECTOR switch Use this switch to match the amplifier output to your speaker impedance. Set this unit in the standby mode before you change the setting of this switch (see page 19). PREPARATION SPEAKER SETUP ■ Use of a subwoofer expands your sound field Subwoofer Main speaker (L) 1.8 m Center speaker Rear speaker (L) ■ Main speakers Place the left and right main speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same. ■ Rear speakers Place these speakers behind your listening position, facing slightly inwards, nearly 1.8 m (approx. 6 feet) above the floor. ■ Center speaker Align the front face of the center speaker with the front face of your video monitor. Place the speaker as close to the monitor as possible, such as directly over or under the monitor and centrally between the main speakers. Note • If the center speaker is not used, the center channel sound will be heard from the left and right main speakers. In this case, “1A CENTER SP” on the SET MENU is set to NONE (see page 41 for details). ADDITIONAL INFORMATION It is also possible to further expand your system with the addition of a subwoofer. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE (low-frequency effect) channel with high fidelity when the Dolby Digital signal or the DTS signal is played back. The YAMAHA Active Servo Processing Subwoofer System is ideal for natural and lively bass reproduction. Rear speaker (R) ADVANCED OPERATION The main speakers should be high-performance models and have enough power-handling capacity to accept the maximum output of your audio system. The other speakers do not have to be equal to the main speakers. For precise sound localization, however, it is ideal to use high-performance models that can reproduce sounds over the full range for the center speaker and the rear speakers. Main speaker (R) BASIC OPERATION The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system. Refer to the following diagram when you place the speakers. PREPARATION This unit has been designed to provide the best soundfield quality with a 5-speaker system, using left and right main speakers, left and right rear speakers, and a center speaker. If you use different brands of speakers (with different tonal qualities) in your system, the tone of a moving human voice and other types of sound may not shift smoothly. We recommend that you use speakers from the same manufacturer or speakers with the same tonal quality. Speaker Placement INTRODUCTION Speakers to Be Used ■ Subwoofer APPENDIX The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce the wall reflections. CAUTION 11 English Some types of speakers interfere with a video monitor. If this problem occurs, move the speakers away from the monitor. If you cannot avoid installing the center speaker or subwoofer near the video monitor, use a magnetically shielded speaker. CONNECTIONS Before Connecting Components CAUTION Never connect this unit and other components to mains power until all connections between components have been completed. • Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some components require different connection methods and have different jack names. Refer to the operation instructions for each component to be connected to this unit. • When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products. • After you have completed all connections, check them again to make sure they are correct. Connecting Audio Components ■ Connecting to digital jacks This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. When you connect components to both the COAXIAL and OPTICAL jacks, priority is given to the input signals from the COAXIAL jack. All digital input jacks are acceptable for 96-kHz sampling digital signals (see page 25 for details). y • You can designate the input for each digital jack according to your component by using “7 I/O ASSIGNMENT” on the SET MENU (see page 44 for details). About the dust protection cap Pull out the cap from the optical jack before you connect the fiber optic cable. Do not discard the cap. When you are not using the optical jack, be sure to put the cap back in place. This cap protects the jack from dust. Note • The OPTICAL jacks on this unit conform to the EIA standard. If you use a fiber optic cable that does not conform to this standard, this unit may not function properly. ■ Connecting a turntable PHONO jacks are for connecting a turntable with an MM or high-output MC cartridge. If you have a turntable with a low-output MC cartridge, use an inline boosting transformer or MC-head amplifier when connecting to these jacks. y • The GND terminal does not electrically ground the turntable. It simply reduces noise in the signal. In some cases, you may hear less noise if you do not connect to the GND terminal. 12 ■ Connecting a CD player y • The COAXIAL CD and OPTICAL CD jacks are available for a CD player which has coaxial or optical digital output jacks. • When you connect a CD player to both the COAXIAL CD and OPTICAL CD jacks, priority is given to the input signals from the COAXIAL CD jack. ■ Connecting an MD recorder, tape deck or CD recorder y • Only digital signals input from a source such as a CD or DVD are output from the DIGITAL OUTPUT jacks. • When you connect your recording component to both the analog and digital input and output jacks, the priority is given to the digital signal. • You can connect an MD recorder to any digital input jack by using “7 I/O ASSIGNMENT” on the SET MENU (see page 44). Notes • When you connect a recording component to this unit, keep its power on while using this unit. If the power is off, this unit may distort the sound from other components. • When you record from a source component connected to this unit while this unit is set in the standby mode, the recorded sound may be distorted. To avoid this problem, turn on this unit. CONNECTIONS OPTICAL INPUT MD recorder or tape deck INPUT OUTPUT R L L R OPTICAL AM ANT OUT (REC) GND FM ANT L UNBAL. CD-R OUT (REC) Y D-TV /LD PB/ CB PR/ CR D-TV/LD Y IN O VCR 1 DVD GND R VIDEO VIDEO COMPONENT DVD DVD CD BASIC OPERATION OUTPUT S VIDEO L CBL /SAT IN (PLAY) 75 R R MD/TAPE CD CD-R L AUDIO L IN (PLAY) O CD player AUDIO TUNER R PREPARATION DIGITAL OUTPUT MD/ TAPE O OPTICAL OUTPUT INPUT L O CD-R OPTICAL OUTPUT CD recorder OUTPUT R INTRODUCTION OPTICAL INPUT PB/ CB OUT D-TV /LD PHONO C COAXIAL OUTPUT PR/ CR IN VCR 2 /DVR OPTICAL COAXIAL MAIN CD CBL /SAT MONITOR OUT Y OUT PB/ CB SURROUND PR/ CR MONITOR OUT (Europe model) CENTER L GND VIDEO 6CH INPUT L R R SURROUND OUTPUT L R MAIN OUTPUT SUBWOOFER OUTPUT CENTER OUTPUT ADDITIONAL INFORMATION OUTPUT S VIDEO ADVANCED OPERATION DIGITAL INPUT SUB WOOFER External decoder See page 18. Turntable indicates signal direction indicates left analog cables R indicates right analog cables O indicates optical cables C indicates coaxial cables APPENDIX L English 13 CONNECTIONS Connecting Video Components ■ About the video jacks There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composit video signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals. The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO jacks are separated into luminance (Y) and color difference (PB/CB, PR/CR) video signals. The jacks are also separated into three for each signal. The description of the component video jacks may be different depending on the component (e.g. Y, CB, CR/Y, PB, PR/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction. If your video component has an S-video output or component video output, you can connect it to this unit. Connect the S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks on your video component to the COMPONENT VIDEO jacks. y Y VIDEO jack (composite) P B/ CB PR/ CR S VIDEO jack COMPONENT VIDEO jacks • Each type of video jack works independently. Signals input through the composite video, S-video and component jacks are output through the corresponding composite video, S-video, and component jacks, respectively. • If you make S-video connections to this unit, it is not necessary to make composite video connections. If both types of connections are made, this unit gives priority to the S-video signal. • You can designate the input for the COMPONENT VIDEO A and B jacks according to your component by using “7 I/O ASSIGNMENT” on the SET MENU (see page 44 for details). Notes • Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when connecting to the COMPONENT VIDEO jacks. • When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being connected. ■ Video monitor with a 21-pin connector Make a connection as shown on page 15 with a commercially available SCART-plug connector cable. ■ VIDEO AUX jacks (on the front panel) S VIDEO VIDEO S V L AUDIO R These jacks are used to connect any video input source such as a game console to this unit. OPTICAL VIDEO AUX L R O OPTICAL OUT AUDIO OUT R AUDIO OUT L VIDEO OUT Game console S VIDEO OUT 14 CONNECTIONS Note • If your LD player has an Dolby Digital RF signal output jack, connect it to this unit through an RF demodulator (separately purchased). AUDIO OUTPUT OPTICAL OUTPUT LD player COMPONENT OUTPUT AUDIO OUTPUT TV/digital TV or LD player VIDEO OUTPUT V S DIGITAL OUTPUT MD/ TAPE AUDIO TUNER R AUDIO L R IN (PLAY) L AM ANT CD-R OPTICAL OUT (REC) GND FM ANT UNBAL. CD-R OUT (REC) PR/ CR Y IN *1 You can connect the Dolby Digital RF signal output of your LD player to the COAXIAL jack by using “7 I/O ASSIGNMENT” on the SET MENU (see page 44). VCR 1 GND O RF demodulator D-TV /LD (Europe model) D-TV/LD DVD RF INPUT Y PB/ CB CBL /SAT IN (PLAY) 75 DVD CD PB/ CB OUT D-TV /LD PHONO O *1 MAIN CD CBL /SAT C PR/ CR IN VCR 2 /DVR OPTICAL COAXIAL C VIDEO OUTPUT MD/TAPE CD CD-R VIDEO VIDEO COMPONENT DVD S VIDEO L V S MONITOR OUT Y OUT PB/ CB SURROUND CENTER DIGITAL INPUT ADVANCED OPERATION PR/ CR MONITOR OUT SUB WOOFER S VIDEO VIDEO 6CH INPUT L R AUDIO OUTPUT V L R L R S S Cable TV or Satellite tuner COAXIAL OUTPUT S VIDEO OUTPUT V V S VIDEO INPUT VIDEO OUTPUT ADDITIONAL INFORMATION S S VIDEO OUTPUT VIDEO OUTPUT VIDEO INPUT VCR 1 or VCR 2/ DVR (digital video recorder) AUDIO INPUT AUDIO OUTPUT APPENDIX No connection indicates signal direction L indicates left analog cables R indicates right analog cables O indicates optical cables C indicates coaxial cables V indicates video cables S V S V VIDEO INPUT SCART-plug indicates S-video cables R S VIDEO INPUT COMPONENT INPUT Video monitor 15 English L BASIC OPERATION R DVD player S VIDEO OUTPUT R L COMPONENT OUTPUT PREPARATION S VIDEO OUTPUT INTRODUCTION RF OUTPUT OPTICAL OUTPUT CONNECTIONS Connecting the Speakers Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. CAUTION • Use speakers with the specified impedance shown on the rear panel of this unit. • Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage the unit and/or speakers. If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers in your configuration after you finish connecting your speakers. ■ Speaker cables A speaker cord is actually a pair of insulated cables running side by side. One of the cables is colored or shaped differently, perhaps with a stripe, groove or ridge. 10 mm (3/8”) 1 1 Remove approx. 10 mm (3/8”) of insulation from each of the speaker cables. 2 Twist the exposed wires of the cable together to prevent short circuits. 2 ■ Connecting to the SPEAKERS terminals Red: positive (+) Black: negative (–) 1 2 1 2 Unscrew the knob. 3 Tighten the knob to secure the wire. Insert one bare wire into the hole in the side of each terminal. 3 ■ MAIN SPEAKERS terminals One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either of the MAIN A or B terminals. ■ REAR SPEAKERS terminals A rear speaker system can be connected to these terminals. ■ CENTER SPEAKER terminals A center speaker can be connected to these terminals. 16 CONNECTIONS Main speakers B Main speakers A Right Left Left (Europe model) INTRODUCTION Right MAINS – SPEAKERS – AC OUTLETS OUTPUT + PREPARATION + R L SWITCHED 100W MAX. TOTAL A MAIN R L MAIN B CENTER + SUB WOOFER – IMPEDANCE SELECTOR SET BEFORE POWER ON CENTER + – – + L MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MAIN A OR B: 8 A + B:16 CENTER :8 :8 REAR MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER BASIC OPERATION R MAIN A OR B: 4 A + B: 8 CENTER :6 :6 REAR R REAR (SURROUND) L REAR (SURROUND) ADVANCED OPERATION Subwoofer connection See “SUBWOOFER jack” on page 18. Right Center speaker Left Rear speakers Subwoofer system ADDITIONAL INFORMATION APPENDIX English 17 CONNECTIONS Connecting to an External Amplifier If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the OUTPUT jacks as follows. Note • When RCA pin plugs are connected to the OUTPUT jacks for output to an external amplifier, it is not necessary to use the corresponding SPEAKERS terminals. Connecting an External Decoder This unit is equipped with 6 additional input jacks (left and right MAIN, CENTER, left and right SURROUND and SUBWOOFER) for discrete multi-channel input from an external decoder, sound processor or pre-amplifier. Connect the output jacks on your external decoder to the 6CH INPUT jacks. Be sure to match the left and right outputs to the left and right input jacks for the main and surround channels. OUTPUT Notes MAIN 1 R L 2 SUB WOOFER CENTER 3 4 R REAR (SURROUND) L 1 MAIN jacks Main channel line output jacks. Note • The signals output through these jacks are affected by the BASS, TREBLE and BASS EXTENSION settings. 2 SUBWOOFER jack When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack. (The cut-off frequency of this jack is 90 Hz.) The LFE (lowfrequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are assigned to this jack. Notes • Adjust the volume level of the subwoofer with the control on the subwoofer. The subwoofer volume cannot be adjusted from this unit. • Depending on the settings of “1 SPEAKER SET”, “10A LFE LEVEL” and “11 DTS LFE LEVEL” on the SET MENU, some signals may not be output from the SUBWOOFER jack. 3 CENTER jack Center channel line output jack. 4 REAR (SURROUND) jacks Rear channel line output jacks. 18 • When you select 6CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you cannot listen to DSP programs. • When you select 6CH INPUT as the input source, changing items 1A to 1E on the SET MENU is not affected. CONNECTIONS IMPEDANCE SELECTOR Switch Select the left or right position according to the impedance of the speakers in your system. Be sure to move this switch only when this unit is in the standby mode. Switch Speaker position MAINS If you use one set of main speakers, the impedance of each speaker must be 4 Ω or higher. AC OUTLETS SWITCHED 100W MAX. TOTAL Left Main If you use two sets of main speakers, the impedance of each speaker must be 8 Ω or higher. Center The impedance must be 6 Ω or higher. Rear SET BEFORE POWER ON MAIN A OR B: 8 MIN. /SPEAKER A + B:16 MIN. /SPEAKER CENTER : 8 MIN. /SPEAKER : 8 MIN. /SPEAKER REAR Main The impedance of each speaker must be 6 Ω or higher. If you use one set of main speakers, the impedance of each speaker must be 8 Ω or higher. If you use two sets of main speakers, the impedance of each speaker must be 16 Ω or higher. Right Center The impedance must be 8 Ω or higher. Rear The impedance of each speaker must be 8 Ω or higher. BASIC OPERAIONT IMPEDANCE SELECTOR MAIN A OR B: 4 MIN. /SPEAKER A + B: 8 MIN. /SPEAKER CENTER : 6 MIN. /SPEAKER : 6 MIN. /SPEAKER REAR Impedance level PREPARATION (Europe model) INTRODUCTION WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit may be damaged. If this unit fails to turn on when STANDBY/ON (or POWER) is pressed, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the standby mode. ADVANCED OPERATION IMPEDANCE SELECTOR Connecting the Power Supply Cords After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if you will not use this unit for a long period of time. (Europe model) MAINS AC OUTLETS SWITCHED 100W MAX. TOTAL SET BEFORE POWER ON MAIN A OR B: 4 MIN. /SPEAKER A + B: 8 MIN. /SPEAKER CENTER : 6 MIN. /SPEAKER : 6 MIN. /SPEAKER REAR MAIN A OR B: 8 MIN. /SPEAKER A + B:16 MIN. /SPEAKER : 8 MIN. /SPEAKER : 8 MIN. /SPEAKER CENTER REAR APPENDIX IMPEDANCE SELECTOR Europe model ............................................... 2 OUTLETS U.K. model ..................................................... 1 OUTLET Use these outlets to connect the power cords from your components to this unit. The power to the AC OUTLET(S) is controlled by this unit’s STANDBY/ON (or POWER and STANDBY). These outlets will supply power to any connected component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the AC OUTLET(S) is 100 W. ADDITIONAL INFORMATION ■ AC OUTLET(S) (SWITCHED) To AC outlet English SWITCHED 19 ON-SCREEN DISPLAY (OSD) You can display the operation information for this unit on a video monitor. If you display the SET MENU and DSP program parameter settings on a monitor, it is much easier to see the available options and parameters than it is by reading this information on the front panel display. Selecting the OSD Mode 1 When you turn on the power, the video monitor and front panel display show the level of the main volume for a few seconds and then switch to show the current DSP program. 2 Press ON SCREEN on the remote control repeatedly to change the display mode. The OSD mode changes in the following order: full display, short display, and display off. y • If a video source is being reproduced, the OSD is superimposed over the image. • The OSD signal is not output to the REC OUT jack, and will not be recorded with any video signal. • You can set the OSD to turn on (blue background) or off when a video source is not being reproduced (or the source component is turned off) by using “14 DISPLAY SET” on the SET MENU (see page 46). OSD Modes You can change the amount of information the OSD shows. Full display This mode always shows the DSP program parameter settings on the video monitor (see page 63). Short display This mode briefly shows the same contents as the front panel display at the bottom of the screen and then disappears. Display off This mode briefly shows the “DISPLAY OFF” message at the bottom of the screen and then disappears. Afterwards, no changes to operations appear on the monitor except those of the ON SCREEN button. P01 CONCERT HALL INIT. DLY ROOM SIZE LIVENESS 45ms 1.0 5 P01 CONCERT HALL Full display Short display y • When you choose the full display mode, INPUT l / h, VOLUME and some other types of operation information are displayed at the bottom of the screen in the same format as that for the front panel display. • The SET MENU and test tone display appear regardless of the OSD mode. 20 Notes • If you choose a video input source that has a component connected to both the S VIDEO IN and composite VIDEO IN jacks, and both the S VIDEO OUT and composite VIDEO OUT jacks are connected to a video monitor, the video signal is output to both the S VIDEO OUT and VIDEO OUT jacks. However, the OSD is carried only on the S-video signal. If no video signal is input, the OSD is carried on both the S-video and composite video signals. • If your video monitor is connected only to the COMPONENT VIDEO jacks of this unit, the OSD is not shown. Make sure to connect your video monitor to the COMPONENT VIDEO jacks and either VIDEO or S VIDEO jacks if you want to see the OSD. • Playing back video software that has an anti-copy signal or video signals with a lot of noise may produce unstable images. SPEAKER MODE SETTINGS Summary of SPEAKER SET Items 1A through 1E Description Initial setting 1A CENTER SP Selects the center channel output mode according to the size of the center speaker. The possible settings are LRG (large), SML (small) and NONE. LRG 1B MAIN SP Selects the main channel output mode according to the size of the main speakers. The possible settings are LARGE and SMALL. LARGE 1C REAR L/R SP Selects the rear channel output mode according to the size of the rear speakers. The possible settings are LRG (large), SML (small) and NONE. 1D LFE/BASS OUT Selects a speaker for the LFE signal output and low bass signal. The possible settings are SWFR (subwoofer), MAIN, and BOTH. BOTH 1E MAIN LEVEL Selects the output level for the main channel signal. The possible settings are Normal and –10 dB. Normal PREPARATION Item INTRODUCTION This unit has 5 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings as well as other possible settings. If the initial settings are not appropriate for your speaker configuration, change the settings on the SET MENU (see page 39). LRG BASIC OPERAIONT ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 21 ADJUSTING THE SPEAKER OUTPUT LEVELS This section explains how to adjust the speaker output levels by using the test tone generator. When this adjustment is made, the output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor, the Dolby Pro Logic decoder, Dolby Digital decoder and DTS decoder. Note • Since this unit cannot enter the test mode while headphones are connected to this unit, be sure to unplug the headphones from the PHONES jack when using the test tone. Using the Test Tone (TEST DOLBY SUR.) Use the test tone to balance the output levels of the 5 speakers required for a surround sound system. The adjustment of each speaker output level should be made at your listening position with the remote control. After completing the adjustments, use VOLUME +/– at your listening position to check if the adjustments are satisfactory. 2,6 1 Before You Begin 5 4 1 INPUT VOLUME 3 6CH INPUT INPUT MODE D I G I T A L D I G I TA L SURROUND STANDBY /ON A/B/C/D/E PRESET/ TUNING EFFECT PROGRAM PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK BASS TREBLE TUNER SPEAKERS A B BASS PROCESSOR EXTENSION DIRECT ON EDIT PHONES OFF MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO MODE START L AUDIO R OPTICAL DSP – SILENT + + VIDEO AUX 2 3 1 – 3 Press STANDBY/ON to turn on the power. Turn on the video monitor. Set the selector dial to the AMP/TUN (or DSP/TUN) position. 2 Press TEST to output the test tone. 3 Adjust the volume so you can hear the test tone. The test tone is heard from the left main speaker, center speaker, right main speaker, right rear speaker and left rear speaker in order. The tone is produced for 2.5 seconds each time. STANDBY /ON 2 Press SPEAKERS A or B to select the main speakers to be used. If you are using two sets of the main speakers, press both A and B. 3 Set BASS and TREBLE on the front panel to the center position and set BASS EXTENSION to OFF. BASS 1 SPEAKERS A B LEFT RIGHT (TEST LEFT) (TEST RIGHT) TREBLE BASS PROCESSOR EXTENSION DIRECT – + – + ON OFF CENTER (TEST CENTER) Set to OFF. LEFT SURROUND (TEST L SUR.) 22 RIGHT SURROUND (TEST R SUR.) ADJUSTING THE SPEAKER OUTPUT CONNECTIONS LEVELS The state of the test tone output is also shown on the monitor by an image of the audio listening room. This is convenient for adjusting each speaker level. LEFT y • The tonal quality of the center speaker can be adjusted by using “5 CENTER GEQ” on the SET MENU (see page 43). • You can increase the output levels of the effect speakers (center, left rear and right rear) to +10 dB. If the output level of these speakers is lower than that of the main speakers even after you have increased the output level of these speakers up to +10 dB, set “1E MAIN LEVEL” on the SET MENU to –10 dB (see page 42). This setting decreases the main speaker output level to about one-third of the normal level. After you have set “1E MAIN LEVEL” on the SET MENU to –10 dB, adjust the levels for the center and rear speakers again. PREPARATION • If “1A CENTER SP” on the SET MENU is set to NONE, the center channel sound is automatically output from the left and right main speakers. Note • If the test tone cannot be heard, turn down the volume, set the unit in the standby mode and check the speaker connections. 4 BASIC OPERAIONT Press LEVEL repeatedly to select the speaker to be adjusted. y • Once you press LEVEL, you can also select the speaker to be adjusted by pressing d. (Pressing u changes the selection in the reverse order.) 6 When the adjustment is complete, press TEST. The test tone stops and the current DSP program appears on the front panel display and on the video monitor. ADDITIONAL INFORMATION Press j / i repeatedly to adjust the output level of the effect speakers so that the output level coming from each speaker is the same. While adjusting, the test tone is heard from the selected speaker. ADVANCED OPERATION 5 INTRODUCTION TEST DOLBY SUR. y APPENDIX English 23 BASIC OPERATION BASIC PLAYBACK When using the remote control, set the selector dial to the AMP/TUN position. 1 3 5 INPUT VOLUME 3 6CH INPUT INPUT MODE D I G I T A L D I G I TA L SURROUND STANDBY /ON A/B/C/D/E PRESET/ TUNING EFFECT PROGRAM PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK BASS 3 Press INPUT l / h repeatedly (or press one of the input selector buttons) to select the input source. • The current input source is indicated on the front panel display with an arrow. • The current input source name and input mode appear on the front panel display and on the video monitor for a few seconds. TREBLE TUNER SPEAKERS A B BASS PROCESSOR EXTENSION DIRECT ON EDIT PHONES OFF MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO MODE START L AUDIO R OPTICAL INPUT DSP + – SILENT – + VIDEO AUX or 2 5 5 6 Front panel 6 VIRTUAL 1 3 DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB Remote control PS PTY RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED VOLUME dB ms D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO 5 Selected input source Select this: 1 Press STANDBY/ON (or POWER) to turn on the power. Turn on the video monitor. The front panel display and the video monitor show the level of the main volume for a few seconds and then switch to show the current DSP program. DVD: D-TV/LD: CBL/SAT: VCR 1: VCR 2/DVR: V-AUX: STANDBY /ON or Front panel 2 24 Press SPEAKERS A or B to select the main speakers to be used. If you are using two sets of main speakers, press both A and B. Remote control SPEAKERS A B Front panel PHONO: CD: TUNER: CD-R: MD/TAPE: To reproduce the signal from this component DVD player TV or digital TV/LD player Cable TV/satellite tuner Video cassette deck 1 Video cassette deck 2/digital video recorder Another A/V component (connected to the VIDEO AUX jacks on the front panel) Turntable CD player AM/FM tuner CD recorder MD recorder/tape deck BASIC PLAYBACK 6 Use the digital sound field processor. See page 28. INTRODUCTION To select a source connected to the 6CH INPUT jacks Press 6CH INPUT until “6CH INPUT” appears on the front panel display and on the video monitor. PROGRAM 6CH INPUT or or Front panel Remote control Front panel Remote control ■ To mute the sound 5 Start playback (or select a broadcast station) on the source component. Refer to the operation instructions for the component. VOLUME or Front panel Remote control TREBLE • You can also cancel mute to press any operation buttons such as VOLUME +/–. • During muting, “MUTE ON” appears on the front panel display and on the video monitor. ■ When you have finished using this unit Press STANDBY/ON (or STANDBY) to set this unit in the standby mode. ■ Notes on the digital signal The digital input jacks of this unit can also handle 96-kHz sampling digital signals. (To utilize this, use a source that supports 96-kHz sampling digital signals and set the player for digital output. Refer to the operation instructions for the player.) Note the following when a 96kHz sampling digital signal is input to this unit: 1. The following indication will appear on the front panel display. BASS PROCESSOR EXTENSION DIRECT VIRTUAL – + – + ON OFF Front panel Note PS PTY RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED VOLUME dB ms D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO 2. DSP programs cannot be selected. Sound will be output as normal 2-channel stereo sound from only the left and right main speakers. Note • If “1B MAIN SP” on the SET MENU is set to SMALL or “1D LFE/BASS OUT” is set to BOTH, the sound is also output from the subwoofer. 3. Adjustment of the speaker output level described on page 47 cannot be made. APPENDIX • If the component connected to the VCR 1 OUT, VCR 2/DVR OUT, CD-R OUT and MD/TAPE OUT jacks is turned off, the reproduced sound may be distorted or the volume may be lowered. In these cases, turn on the component. DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB ADDITIONAL INFORMATION BASS y ADVANCED OPERATION Adjust the volume to the desired output level. If desired, use BASS, TREBLE and BASS EXTENSION etc. These controls are only effective for sound from the main speakers. Press MUTE on the remote control. To restore the audio output to the previous volume level, press MUTE again. BASIC OPERATION 4 PREPARATION Notes • If “6CH INPUT” is shown on the front panel display and on the video monitor, no other source can be played. To select another input source with INPUT l / h (or the input selector buttons), press 6CH INPUT to turn off “6CH INPUT” from the front panel display and the video monitor. • If you want to enjoy an audio source connected to the 6CH INPUT jacks together with a video source, first select the video source and then press 6CH INPUT. English 25 BASIC PLAYBACK ■ BGV (background video) function The BGV function allows you to combine a video image from a video source with a sound from an audio source. (For example, you can listen to classical music while you are watching a video.) Select a source from the video group and then select a source from the audio group with the input selector buttons on the remote control. The BGV function does not work if you select the sources with INPUT l / h on the front panel. AUTO: In this mode, the input signal is automatically selected in the following order: 1) Dolby Digital or DTS signal 2) Digital (PCM) signal 3) Analog signal DTS: In this mode, only the digital input signal encoded with DTS is selected even if another signal is input at the same time. ANALOG: In this mode, only the analog input signal is selected even if a digital signal is input at the same time. Notes Input Modes and Indications This unit comes with various input jacks. If your component is connected to more than one type of input jack, you can set the priority of the input signal. When you turn on the power of this unit, the input mode is set according to “8 INPUT MODE” on the SET MENU (see page 44 for details). Press INPUT MODE (or the input selector button that you have pressed to select the input source on the remote control) repeatedly until the desired input mode is shown on the front panel display and on the video monitor. INPUT MODE or Front panel VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB Remote control PS PTY RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED VOLUME dB ms Input mode 26 D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO • If digital signals are input from both the COAXIAL and OPTICAL jacks, the digital signal from the COAXIAL jack is selected. • When AUTO is selected, this unit automatically determines the type of signal. If this unit detects a Dolby Digital or DTS signal, the decoder automatically switches to the appropriate setting and reproduces 5.1 channel source. • The sound output may be interrupted for some LD and DVD players in the following situation: The input mode is set to AUTO. A search is performed while playing the disc encoded with Dolby Digital or DTS, and then disc playing is restored. The sound output is interrupted for a moment because the digital signal was selected again. BASIC PLAYBACK ■ Notes on playing a source encoded with a DTS signal PREPARATION • For LD software that does not contain a digital soundtrack, connect the LD player to the analog jacks and set the input mode to AUTO or ANALOG. • If the LD player is transmitting a signal by a nonstandard method, this unit cannot detect the Dolby Digital or DTS signal. In this case, the decoder automatically switches to PCM or analog. • Some A/V components such as LD players output different audio signals through their analog and digital jacks. Change the input mode as necessary. • While you are operating the LD player and playing a disc encoded with a Dolby Digital signal, if you switch from the pause or chapter forwarding function to normal playback, you may hear the PCM or analog sound an instant before the Dolby Digital signal is played. INTRODUCTION BASIC OPERATION ADVANCED OPERATION ADDITIONAL INFORMATION • If the digital output data of the player has been processed in any way, you may not be able to perform DTS decoding even if you make a digital connection between this unit and the player. • If you play a source encoded with a DTS signal and set the input mode to ANALOG, this unit reproduces the noise of an unprocessed DTS signal. When you want to play a DTS source, be sure to connect the source to a digital input jack and set the input mode to AUTO or DTS. • If you switch the input mode to ANALOG while playing a source encoded with a DTS signal, this unit reproduces no sound. • If you play a source encoded with a DTS signal and set the input mode to AUTO, there will be a moment of noise while the unit recognizes the DTS signal and turns on the DTS decoder. This is not a malfunction. You can avoid this by setting the input mode to DTS beforehand. • If you continue to play a source encoded with a DTS signal with the input mode setting left to AUTO, this unit automatically switches to the “DTS-decoding” mode to prevent noise from being generated during subsequent operation. (The “t” indicator lights up on the front panel display.) The “t” indicator will flash immediately after playback of a source encoded with a DTS signal has finished. Only a source encoded with a DTS signal can be played back while this indicator is flashing. If you want to play a normal PCM source soon, set the input mode back to AUTO. • The “t” indicator will flash when the input mode is set to AUTO and a search or skip operation is performed while playing back a source encoded with a DTS signal. If this status continues for 30 or more seconds, the unit will automatically switch from the “DTS-decoding” mode to PCM digital signal input mode and the “t” indicator will go out. ■ Notes on playing an LD source APPENDIX English 27 BASIC PLAYBACK 2 Selecting a Sound Field Program You can enhance your listening experience by selecting a DSP program. For details about each program, see pages 57 to 60. INPUT VOLUME 6CH INPUT INPUT MODE D I G I T A L D I G I TA L SURROUND STANDBY /ON A/B/C/D/E PRESET/ TUNING EFFECT PROGRAM PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK BASS Use the numeric buttons to select the desired program before the indicator goes off (or press PROGRAM l / h repeatedly on the front panel). • For example, to select the sub-program “Spectacle”, press MOVIE THEATER 1 repeatedly. • The name of the selected program appears on the front panel display and on the video monitor. TREBLE TUNER SPEAKERS A B BASS PROCESSOR EXTENSION DIRECT ON OFF EDIT PHONES MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO MODE START L AUDIO R OPTICAL DSP – SILENT + – + VIDEO AUX PROGRAM or 2 Front panel 1 Remote control Program group VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB 2 DTS MOVIE THEATER 1 2 PS PTY RT CT PTY HOLD EON STEREO AUTO ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP MEMORY TUNED VOLUME dB ms D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO Program name (sub-program) Notes 1 Press DSP on the remote control. The indicator lights up for about 3 seconds. Remote control y • If the selector dial is set to the DSP/TUN position, skip this step. 28 • Choose a DSP program based on your listening preference, and not on the name of the program. The acoustics of your listening room affect the DSP program. Minimize the sound reflections in your room to maximize the effect created by the program. • When you select an input source, this unit automatically selects the last DSP program used with that source. • When you set this unit in the standby mode, the current source and DSP program are memorized and are automatically selected when you turn on the power again. • If a Dolby Digital or DTS signal is input when the input mode is set to AUTO, the DSP program automatically switches to the appropriate decoding program. • When a monaural source is being played with PRO LOGIC/ Normal or PRO LOGIC/ENHANCED, no sound will be heard from the main speakers and the rear speakers. Sound can only be heard from the center speaker. However, if “1A CENTER SP” on the SET MENU is set to NONE, the center channel sound is output from the main speakers. • When a source connected to the 6CH INPUT jacks of this unit is selected, the digital sound field processor cannot be used. • When 96-kHz sampling digital signals are input to this unit, the DSP program cannot be selected. In this case, the sound is reproduced as normal 2-channel stereo. BASIC PLAYBACK ■ Dolby Digital Matrix 6.1 or DTS ES decoder Normal Stereo Reproduction Press EFFECT to turn off the sound effect for normal stereo reproduction. Press EFFECT again to turn the sound effect back on. EFFECT or Remote control Front panel DTS MOVIE THEATER 1 2 PS PTY RT CT PTY HOLD EON STEREO AUTO ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP MEMORY TUNED VOLUME D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO The “ c ” indicator lights up. ■ Virtual CINEMA DSP and SILENT CINEMA DSP y • If the selector dial is set to a position other than the DSP/TUN position, first press DSP and then EFFECT on the remote control. Notes • If you turn off the sound effect, no sound is output from the center and rear speakers. • If you turn off the sound effect while a Dolby Digital or DTS signal is being output, the dynamic range of the signal is automatically compressed and the sounds of the center and rear speaker channels are mixed and output from the main speakers. • The volume may be greatly reduced when you turn off the sound effect or if you set “10B D-RANGE” on the SET MENU to MIN. In this case turn on the sound effect. BASIC OPERATION You can experience the virtual CINEMA DSP sound field by setting “1C REAR L/R SP” on the SET MENU to NONE. The sound field processing is changed to the Virtual CINEMA DSP mode according to the selected DSP program. Virtual CINEMA DSP is performed by using the main speakers. You can also listen to SILENT CINEMA DSP by connecting your headphones to the PHONES jack while the digital sound field processor is on. Remote control PREPARATION VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB INTRODUCTION If you want to use the Dolby Digital Surround EX or DTS ES software, press 6.1/ES to turn on the Dolby Digital Matrix 6.1 or DTS ES decoder (see “12 6.1/ES AUTO” on pages 45 and 60 for details). ADVANCED OPERATION Note ADDITIONAL INFORMATION • This unit is not set in the virtual CINEMA DSP mode even if “1C REAR L/R SP” is set to NONE in the following cases: – when the 5ch Stereo, DOLBY DIGITAL/Normal or DTS/ Normal program is selected; – when the sound effect is turned off; – when 6CH INPUT is selected as the input source; – when 96-kHz sampling digital signals are input to this unit; – when the Dolby Digital KARAOKE source is played; – when using the test tone; or – when connecting the headphones. APPENDIX English 29 TUNING Connecting the Antennas Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals. AM loop antenna (included) Indoor FM antenna (included) (Europe model) DIGITAL OUTPUT MD/ TAPE CD-R OPTICAL TUNER 3 Release the tab to lock the lead wires. Lightly pull the lead wires to confirm a good connection. 4 Attach the loop antenna to the antenna stand. 5 Orient the AM loop antenna so that the best reception is obtained. AM ANT GND CD CD-R 75 UNBAL. y FM ANT • The AM loop antenna can be removed from the stand and attached to a wall, etc. DVD GND D-TV /LD Notes OPTICAL COAXIAL • The AM loop antenna should be placed away from this unit. • The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit. CD CBL /SAT DIGITAL INPUT Ground (GND terminal) For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas. ■ Connecting the indoor FM antenna Connecting a coaxial cable to the included 75-ohm/300-ohm antenna adapter (U.K. model only) Connect the included indoor FM antenna to the 75Ω UNBAL. FM ANT terminal. 1 2 Note • Do not connect an outdoor FM antenna and the indoor FM antenna at the same time. ■ Connecting the AM loop antenna 2 Cover Open the cover of the included 75-ohm/300-ohm antenna adapter. Cut the external sleeve of the 75-ohm coaxial cable and prepare it for connection. Lead wire Cut the lead wire and remove it. 5 4 Antenna stand 1 2 30 Unit: mm (inch) 3 1 3 4 11 (7/16) 8 (5/16) 6 (1/14) Press and hold the tab to unlock the terminal hole. Insert the AM loop antenna lead wires into the AM ANT and GND terminals. Clamp with pliers. 5 Clamp with pliers. Insert the wire into the slot. Insert the cable wire into the slot, and clamp it with pliers. Snap the cover into place. TUNING y Automatic (or Manual) Tuning Automatic tuning is effective when station signals are strong and there is no interference. 1 INPUT VOLUME 6CH INPUT INPUT MODE INTRODUCTION • Use the manual tuning method if the tuning search does not stop at the desired station because the signal is weak. • When tuned in to a station, the “TUNED” indicator lights up and the frequency of the received station is shown on the front panel display. If an RDS station that offers the PS data service is being received, the station name is shown instead of the frequency on the front panel display. D I G I T A L If the signal from the station you want to select is weak, you must tune in to it manually. D I G I TA L SURROUND STANDBY /ON A/B/C/D/E PRESET/ TUNING EFFECT PROGRAM PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK BASS TREBLE 3 TUNER SPEAKERS A B BASS PROCESSOR EXTENSION DIRECT ON OFF EDIT PHONES MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO MODE START L AUDIO R OPTICAL DSP – SILENT + – + VIDEO AUX PREPARATION Press TUNING MODE (AUTO/MAN’L MONO) so that the “AUTO” indicator goes off from the front panel display. TUNING MODE 4 2 3 AUTO/MAN'L MONO Press INPUT l / h to select TUNER as the input source. 2 Press FM/AM to select the reception band. “FM” or “AM” appears on the front panel display. If the colon (:) appears on the front panel display next to the band indication, press PRESET/TUNING (EDIT) to turn it off. INPUT PRESET /TUNING EDIT FM/AM VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB PS Turn this indicator off. Press TUNING MODE (AUTO/MAN’L MONO) so that the “AUTO” indicator lights up on the front panel display. 4 AUTO AUTO/MAN'L MONO PRESET /TUNING Note VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB PS PTY • Manually tuning in to an FM station will automatically change the reception mode to monaural to increase the signal quality. RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINM ENTERTAINMENT MEMORY TUNED ADDITIONAL INFORMATION EDIT Press PRESET/TUNING l / h to tune in to the desired station manually. PRESET/ Hold down the button to TUNING continue the tuning search. Lights up If the colon (:) appears on the front panel display next to the band indication, press PRESET/TUNING (EDIT) to turn it off. dB ms Turn this indicator off. 4 CT ADVANCED OPERATION TUNING MODE RT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINM ENTERTAINMENT MEMORY TUNED or 3 PTY BASIC OPERATION 1 AUTO Goes off APPENDIX Press PRESET/TUNING l or h once to begin automatic tuning. Press h to tune in to a higher PRESET/ TUNING frequency, or press l to tune in to a lower frequency. Press the same button again if the tuning search does not stop at the desired station. English 31 TUNING Notes Presetting Stations ■ Automatically presetting stations (for RDS stations) You can use the automatic preset tuning feature to store RDS stations. This function enables the unit to automatically tune in to RDS stations with strong signals, and to store up to 40 (8 stations x 5 groups) of those stations in order. (See pages 35 to 37 for details on RDS stations.) This feature enables you to easily tune in to any preset station by selecting the preset station number (see page 33). INPUT VOLUME 6CH INPUT INPUT MODE D I G I T A L D I G I TA L SURROUND STANDBY /ON A/B/C/D/E PRESET/ TUNING EFFECT PROGRAM PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK BASS • Any stored station data existing under a preset number is cleared when you store a new station under that preset number. • You can manually replace a preset station with another FM or AM station by simply following the procedure in the section “Manually presetting stations” on page 33. • If the number of the received stations does not reach E8, automatic preset tuning has automatically stopped after searching all stations. • Only RDS stations with sufficient signal strength are stored automatically by automatic preset tuning. If the station you want to store is weak in signal strength, tune in to it manually in the monaural mode, and store it by following the procedure in “Manually presetting stations” on page 33. (There may be a case that this unit cannot receive a station which could be received by using the automatic tuning method. This is because this unit receives a large amount of PI (Program Identification) data along with the station.) TREBLE TUNER SPEAKERS A B BASS PROCESSOR EXTENSION DIRECT ON EDIT PHONES OFF MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO MODE START L AUDIO R OPTICAL DSP – SILENT + + – VIDEO AUX 132 1 Press FM/AM to select the FM band. FM/AM 2 Press TUNING MODE (AUTO/MAN’L MONO) so that the “AUTO” indicator lights up on the front panel display. TUNING MODE AUTO Lights up AUTO/MAN'L MONO 3 Press and hold MEMORY (MAN’L/AUTO FM) for more than 3 seconds. The preset number, the “MEMORY” and “AUTO” indicators flash. Then, after about 5 seconds, automatic preset tuning begins from the frequency currently displayed toward the higher frequencies. MEMORY MAN'L/AUTO FM VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB PS PTY RT Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the preset stations may be cleared. If so, store the stations again by using the presetting station methods. CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 ZO NEWS INFO AFFAIRS SPORT SLEEP SLE PRO LOGIC ENTERTAINMENT MEMORY TUNED When automatic preset tuning is completed, the front panel display shows the frequency of the last preset station. 32 Automatic preset tuning options You can select the preset number from which the unit will store RDS stations and/or begin tuning toward lower frequencies. Before automatic preset tuning begins (after pressing MEMORY in step 3): 1. Press A/B/C/D/E and PRESET/TUNING l / h to select the preset number under which the first station will be stored. Automatic preset tuning will stop when stations have all been stored up to E8. 2. Press PRESET/TUNING (EDIT) to turn off the colon (:) and then press PRESET/TUNING l to begin tuning toward lower frequencies. dB ms TUNING ■ Manually presetting stations 5 INPUT VOLUME 6CH INPUT INPUT MODE D I G I T A L D I G I TA L SURROUND STANDBY /ON A/B/C/D/E PRESET/ TUNING EFFECT PROGRAM PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK BASS TREBLE TUNER SPEAKERS A B BASS PROCESSOR EXTENSION DIRECT ON OFF EDIT PHONES MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO VIRTUAL MODE START L AUDIO R OPTICAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB DSP – SILENT + – + VIDEO AUX PS PTY RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED VOLUME dB ms DVD MD/TAPE CD-R TUNER CD PHONO D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX INTRODUCTION Press MEMORY (MAN’L/AUTO FM) while the “MEMORY” indicator is flashing. The station band and MEMORY frequency appear on the front MAN'L/AUTO FM panel display with the preset group and number you have selected. You can also store up to 40 stations (8 stations x 5 groups) manually. Shows the displayed station has been stored as A1. 6 2,5 Repeat steps 1 to 5 to store other stations. Notes 1 Tune in to a station. See page 31 for tuning instructions. 2 Press MEMORY (MAN’L/AUTO FM). The “MEMORY” indicator flashes for about 5 seconds. MEMORY Flashes 3 You can tune any desired station simply by selecting the preset station number under which it was stored. You can also tune a preset station with the remote control. Set the selector dial to the AMP/TUN position and press TUNER to select TUNER as the input source. INPUT VOLUME 6CH INPUT INPUT MODE D I G I T A L D I G I TA L SURROUND STANDBY /ON A/B/C/D/E VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB PS PTY RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP MEMORY TUNED PRO LOGIC ENTERTAINMENT ENTERTAINM SPEAKERS A B A/B/C/D/E PRESET/ TUNING EFFECT PROGRAM PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ ON dB ms OFF EDIT PHONES MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO PTY SEEK BASS TREBLE MODE START L AUDIO R OPTICAL DSP – SILENT 4 EON TUNER BASS PROCESSOR EXTENSION DIRECT Press PRESET/TUNING l / h to select a preset station number (1 to 8) while the “MEMORY” indicator is flashing. Press h to select a higher PRESET/ TUNING preset station number. Press l to select a lower preset station number. + – + VIDEO AUX ADDITIONAL INFORMATION 1 2 ADVANCED OPERATION Press A/B/C/D/E repeatedly to select a preset station group (A to E) while the “MEMORY” indicator is flashing. The group letter appears and make sure that the colon (:) appears on the front panel display next to the band indication. Tuning in to a Preset Station BASIC OPERATION MEMORY MAN'L/AUTO FM • Any stored station data existing under a preset number is cleared when you store a new station under that preset number. • The reception mode (stereo or monaural) is stored along with the station frequency. PREPARATION 3 4 APPENDIX 2 1 English 33 TUNING 1 Press A/B/C/D/E to select the preset station group. The preset group letter appears on the front panel display and changes each time you press A/B/C/D/E. A/B/C/D/E Exchanging Preset Stations You can exchange the assignment of two preset stations with each other. The example below describes the procedure for exchanging preset station “E1” with “A5”. or INPUT VOLUME 6CH INPUT INPUT MODE A/B/C/D/E D I G I T A L Front panel Remote control D I G I TA L SURROUND STANDBY /ON 2 Press PRESET/TUNING l / h (or PRESET –/+) to select a preset station number (1 to 8). The preset group and number appear on the front panel display along with the station band, frequency and the “TUNED” indicator lights up. PRESET/ TUNING VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB PS PTY RT CT VOLUME dB ms D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX OFF PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EDIT PHONES MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO EON PTY SEEK BASS TREBLE MODE START L AUDIO R OPTICAL – + + – VIDEO AUX 2,4 1 Tune in to preset station “E1”. See “Tuning in to a Preset Station” on page 33. 2 Press and hold PRESET/TUNING (EDIT) for more than 3 seconds. “E1” and the “MEMORY” indicator flash on the front panel display. DVD MD/TAPE CD-R TUNER CD PHONO PRESET /TUNING 3 PTY VIRTUAL CT ZONE 2 SLEEP PS PTY RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED dB ms Press PRESET/TUNING (EDIT) again. The stations stored at the two preset assignments are exchanged. PRESET /TUNING EDIT VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB PS PTY RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE ZON 2 NEWS INFO AFFAIRS SPORT SLE SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED Shows the exchange of stations has been completed. 34 RT DTS MOVIE THEATER 1 2 PTY HOLD EON DOLBY DIGITAL NEWS INFO AFF AFFAIRS SPORT PRO LOGIC ENTERTAINMENT MEMORY T Tune in to preset station “A5” by using the buttons on the front panel. “A5” and the “MEMORY” indicator flash on the front panel display. DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB 4 PS VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB EDIT y • You can select the preset station number with the numeric buttons (1 to 8) on the remote control if code number “0023” has been set up in the AMP/TUN (or DSP/TUN) position. PROGRAM DSP SILENT Remote control DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED PRESET/ TUNING EFFECT BASS PROCESSOR EXTENSION DIRECT ON or Front panel A/B/C/D/E TUNER SPEAKERS A B dB ms RECEIVING RDS STATIONS Description of RDS Data This unit can receive PI, PS, PTY, RT, CT, and EON data when receiving RDS broadcasting stations. The name of the RDS station being received is displayed. ■ PTY (Program Type) mode: ■ RT (Radio Text) mode: ■ CT (Clock Time) mode: The current time is displayed and updated every minute. If the data are accidentally cut off, “CT WAIT” may appear. ■ EON (Enhanced Other Networks): RDS MODE /FREQ PS mode PTY mode ADDITIONAL INFORMATION Information about the program (such as the title of the song, name of the singer, etc.) on the RDS station being received is displayed by a maximum of 64 alphanumeric characters, including the umlaut symbol. If other characters are used for RT data, they are displayed with under-bars. ADVANCED OPERATION The program type on the RDS station being received is displayed. There are 15 program types to classify RDS stations. You can make this unit search for a station which is broadcasting a program of the desired type. See page 36 for details. Notes • When an RDS station is being received, do not press RDS MODE/FREQ until one or more RDS mode indicators light up on the front panel display. If you press the button before the indicators light up on the front panel display, the mode cannot be changed. This is because the unit has not yet received all of the RDS data on the station. • RDS data not offered by the station cannot be selected. • The RDS data service cannot be utilized by this unit if the received signal is not strong enough. In particular, the RT mode requires a large amount of data to be received, so it is possible that the RT mode may not be displayed even if other RDS modes (PS, PTY, etc.) are displayed. • RDS data cannot sometimes be received under poor reception conditions. If so, press TUNING MODE so that the “AUTO” indicator goes off from the front panel display. Although the reception mode is changed to monaural by this operation, when you change the display to RDS mode, RDS data may be displayed. • If the signal strength is weakened by external interference during the reception of an RDS station, the RDS data service may be cut off suddenly and “...WAIT” will appear on the front panel display. BASIC OPERATION ■ PS (Program Service name) mode: The four modes are available in this unit for displaying RDS data. When an RDS station is being received, PS, PTY, RT and/or CT mode indicators that correspond to the RDS data services offered by the station light up on the front panel display. Press RDS MODE/FREQ repeatedly to change the display mode among the RDS data offered by the transmitting station in the order shown below. Illumination of the red indicator next to the RDS mode indicator shows that the corresponding RDS mode is now selected. PREPARATION RDS data contains various information such as PI (Program Identification), PS (Program Service name), PTY (Program Type), RT (Radio Text), CT (Clock Time), EON (Enhanced Other Networks), etc. The RDS function is carried out among the network stations. Changing the RDS Mode INTRODUCTION RDS (Radio Data System) is a data transmission system by FM stations in many countries. Stations using this system transmit an inaudible stream of data in addition to the normal radio signal. See page 37. APPENDIX RT mode CT mode English Frequency display mode 35 RECEIVING RDS STATIONS ■ To cancel this function PTY SEEK Function Press PTY SEEK MODE twice. If you select the desired program type, the unit automatically searches all preset RDS stations that are broadcasting a program of the required type. INPUT VOLUME ■ Program types in the PTY mode There are 15 program types to classify RDS stations. NEWS AFFAIRS INFO SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED POP M ROCK M M.O.R. M 6CH INPUT INPUT MODE D I G I T A L D I G I TA L SURROUND STANDBY /ON A/B/C/D/E PRESET/ TUNING EFFECT PROGRAM PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK BASS TREBLE TUNER SPEAKERS A B BASS PROCESSOR EXTENSION DIRECT ON EDIT PHONES OFF MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO MODE START L AUDIO R OPTICAL DSP + – SILENT 2 1 – + VIDEO AUX 1 3 Press PTY SEEK MODE to set the unit in the PTY SEEK mode. The program type of the station being received or “NEWS” flashes on the front panel display. LIGHT M CLASSICS OTHER M VIRTUAL PTY SEEK MODE START Flashes 2 Press PRESET/TUNING l / h to select the desired program type. The selected program type appears on the front panel display. PRESET/ TUNING 3 Press PTY SEEK START to begin searching all preset RDS stations. The selected program type flashes and the “PTY HOLD” indicator lights up on the front panel display while searching for stations. Light up PTY SEEK VIRTUAL MODE START DIGITAL PRO LOGIC DSP 6.1/ES PCM B PS PTY RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED dB ms The selected program type flashes. • If a station that is broadcasting a program of the required type is found, the unit stops at that station. • If the called station is not the desired one, press PTY SEEK START again. The unit begins searching for another station that is broadcasting a program of the same type. 36 News Current affairs General information Sports Education Drama Culture Science Light entertainment Pops Rock Middle-of-the-road music (easylistening) Light classics Serious classics Other music RECEIVING RDS STATIONS 2 EON Function EON Lights up Note VIRTUAL DTS INPUT VOLUME 6.1/ES PCM D I G I TA L SURROUND A/B/C/D/E PRESET/ TUNING EFFECT PROGRAM PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK BASS dB ms BASS PROCESSOR EXTENSION DIRECT ON OFF EDIT PHONES MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO VIRTUAL DTS MODE START L AUDIO R OPTICAL 2 SILENT DVD MD/TAPE CD-R TUNER CD PHONO + – + PS PTY RT CT PTY HOLD EON STEREO AUTO ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP MEMORY TUNED VOLUME VIDEO AUX 6.1/ES PCM dB ms B D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO Flashes • When broadcasting of the required program ends, the previously received station (or another program on the same station) is recalled. 2 1 VIRTUAL DTS 6.1/ES PCM B 2 PS PTY RT CT PTY HOLD EON STEREO AUTO ZONE 2 INFO AFFAIRS SPORT SLEEP MEMORY TUNED VOLUME dB ms D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO VIRTUAL DTS 6.1/ES PCM B 2 PS PTY RT CT PTY HOLD EON STEREO AUTO ZONE 2 INFO AFFAIRS SPORT SLEEP MEMORY TUNED VOLUME dB ms D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO ■ To cancel this function Press EON repeatedly until no program type name lights up on the front panel display. ADVANCED OPERATION Make sure that the “EON” indicator lights up on the front panel display. If the “EON” indicator does not light up, tune in to another RDS station so that the “EON” indicator lights up. BASIC OPERATION DSP – D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX TREBLE TUNER SPEAKERS A B VOLUME • If a preset RDS station of the selected program type starts broadcasting, the unit will automatically switch from the program being currently received to that program. The program type name indicator flashes. D I G I T A L STANDBY /ON PS PTY RT CT PTY HOLD EON STEREO AUTO ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP MEMORY TUNED B 6CH INPUT INPUT MODE 2 PREPARATION • This function can only be used when an RDS station that offers the EON data service is being received. When such a station is being received, the “EON” indicator lights up on the front panel display. INTRODUCTION This function uses the EON data service on the RDS station network. If you simply select the desired program type (NEWS, INFO, AFFAIRS or SPORT), the unit automatically searches for all preset RDS stations that are scheduled to broadcast a program of the required type and switches from the station being currently received to the new station when the broadcasts starts. Press EON repeatedly to select the desired program type (NEWS, INFO, AFFAIRS or SPORT). The selected program type name indicator lights up on the front panel display. ADDITIONAL INFORMATION APPENDIX English 37 BASIC RECORDING Recording adjustments and other operations are performed from the recording components. Refer to the operation instructions for these components. 2 INPUT VOLUME 6CH INPUT INPUT MODE D I G I T A L D I G I TA L SURROUND STANDBY /ON A/B/C/D/E PRESET/ TUNING EFFECT PROGRAM PRESET TUNING RDS MODE /TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK BASS TREBLE TUNER SPEAKERS A B BASS PROCESSOR EXTENSION DIRECT ON EDIT PHONES OFF MAN'L/AUTO FM AUTO/MAN'L MONO S VIDEO VIDEO MODE START L AUDIO R OPTICAL DSP – SILENT + – + VIDEO AUX 2 1 2 If you playback a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture itself may be disturbed due to those signals. Turn on the power to the unit and all connected component. Select the source component you want to record from. INPUT or Front panel Remote control 3 Start playback (or select a broadcast station) on the source component. 4 Start recording on the recording component. 38 Notes • Do a test recording before you start an actual recording. • When this unit is set in the standby mode, you cannot record between other components connected to this unit. • The setting of BASS, TREBLE, BASS EXTENSION, VOLUME, “3 L/R BALANCE” on the SET MENU and DSP programs does not affect the recorded material. • A source connected to the 6CH INPUT jacks of this unit cannot be recorded. • S-video and composite video signals pass independently through this unit’s video circuits. Therefore, when recording or dubbing video signals, if your video source component is connected to provide only an S-video (or only a composite video) signal, you can record only an S-video (or only a composite video) signal by your VCR. • A given input source is not output on the same REC OUT channel. (For example, the signal input from VCR 1 IN is not output on VCR 1 OUT.) • Check the copyright laws in your country to record from records, CDs, radio, etc. Recording of copyrighted material may infringe copyright laws. ■ Special considerations when recording DTS software The DTS signal is a digital bitstream. Attempting to digitally record the DTS bitstream will result in noise being recorded. Therefore, if you want to use this unit to record sources that have DTS signals recorded on them, the following considerations and adjustments need to be made. For LDs, DVDs and CDs encoded with DTS Only 2-channel analog audio signals may be recorded as follows: • LDs Set your LD player’s left and right outputs to the analog soundtrack. • DVDs Use the disc menu to set the DVD player’s mixed 2channel left and right audio outputs to the PCM or Dolby Digital soundtrack. • CDs The DTS signal recorded on CDs can only be output as a digital bitstream, and therefore cannot be recorded. ADVANCED OPERATION SET MENU y INTRODUCTION The SET MENU consists of 15 items including the speaker mode setting, center graphic equalizer and parameter initialization features. Choose the appropriate item and adjust or select the values as necessary. Adjusting the Items on the SET MENU Adjustment should be made with the remote control. 3,6 4,5 2 1 PREPARATION • You can adjust the items on the SET MENU while playing a source. • We recommend that you adjust the items on the SET MENU while using a video monitor. It is easier to see the video monitor than it is to see the front panel display on this unit while adjusting the items. Note • The indication on the front panel display is the abbreviation of the OSD. 1 SPEAKER SET 1A CENTER SP 1C REAR L/R SP Note • Some items require extra steps to change to the desired setting. 1 Set the selector dial to the AMP/TUN (or DSP/TUN) position. 2 Press SET MENU to enter the SET MENU. 1D LFE/BASS OUT 1E MAIN LEVEL 3 L/R BALANCE 4 HP TONE CTRL 5 CENTER GEQ 6 INPUT RENAME 7 I/O ASSIGNMENT 8 INPUT MODE 9 PARAM. INI SET MENU 1/4 1 SPEAKER SET 2 LOW FRQ TEST 3 L/R BALANCE 4 HP TONE CTRL / :Up/Down –/+ Enter 3 Press u/d repeatedly to select the item (1 to 15) you want to adjust. ADDITIONAL INFORMATION LOW FRQ TEST ADVANCED OPERATION 2 SET MENU 1/4 10 DOLBY D. SET 1 SPEAKER SET 2 LOW FRQ TEST 3 L/R BALANCE 4 HP TONE CTRL / :Up/Down –/+ Enter 10A LFE LEVEL 10B D-RANGE y 12 6.1/ES AUTO • By pressing SET MENU repeatedly, you can select items in the same order as when pressing d. 13 SP DELAY TIME 4 15 MEMORY GUARD Press j or i once to enter the setup mode of the selected item. The last setting you adjusted appears on the video monitor or on the front panel display. APPENDIX 11 DTS LFE LEVEL 14 DISPLAY SET BASIC OPERAIONT 1B MAIN SP 2 LOW FRQ TEST English TEST TONE • • • • • OFF OUTPUT • • • MAIN L/R FRQ • • • • • • • • • • 88Hz 39 SET MENU Depending on the item, press u/d to select a sub item. 2 LOW FRQ TEST TEST TONE • • • • • OFF OUTPUT • • • MAIN L/R FRQ • • • • • • • • • 88Hz 1 SPEAKER SET (speaker mode settings) Use this feature to select suitable output modes for your speaker configuration. You must set the output mode when you use a subwoofer. Notes 5 Press j / i repeatedly to change the setting of the item. 2 LOW FRQ TEST TEST TONE • • • • • •ON OUTPUT • • • MAIN L/R FRQ • • • • • • • • • 88Hz 6 Press u/d repeatedly until the current DSP program appears or simply press one of the DSP program group button to exit from the SET MENU. or • When 96-kHz sampling digital signals are input to this unit, level adjustments in items 1B and 1D are possible, but those in items 1A,1C and 1E are not affected. • When 6CH INPUT is selected as the input source, level adjustments in items 1A through 1E are not affected. ■ 1A CENTER SP (center speaker mode) By adding a center speaker to your speaker configuration, the unit can provide good dialog localization for many listeners and superior synchronization of sound and images. The OSD shows a large, small or no center speaker depending on how you set this item. Choices: LRG (large), SML (small), NONE Initial setting: LRG LRG Select this if you have a large center speaker. The entire range of the center channel signal is directed to the center speaker. 1A CENTER SP Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the settings of the SET MENU you adjusted will return to the factory settings. If so, adjust the items again. LRG SML NONE SML Select this if you have a small center speaker. The lowfrequency signals (90 Hz and below) of the center channel are directed to the speakers selected with “1D LFE/BASS OUT”. 1A CENTER SP LRG SML NONE 40 SET MENU 1A CENTER SP LRG SML NONE The OSD shows large, small or no rear speakers depending on how you set this item. Choices: LRG (large), SML (small), NONE Initial setting: LRG LRG Select this if you have large left and right rear speakers or if a rear subwoofer is connected to the rear speakers. The entire range of the rear channel signal is directed to the left and right rear speakers. The OSD shows large or small main speakers depending on how you set this item. 1C REAR L/R SP Choices: LARGE, SMALL Initial setting: LARGE LRG SML NONE 1B MAIN SP SML Select this if you have small left and right rear speakers. The low-frequency signals (90 Hz and below) of the rear channel are directed to the speakers selected with “1D LFE/BASS OUT”. 1C REAR L/R SP SMALL ADVANCED OPERATION SMALL Select this if you have small main speakers. The lowfrequency signals (90 Hz and below) of the main channel are directed to the speakers selected with “1D LFE/BASS OUT”. LRG SML NONE NONE Select this if you do not have rear speakers. ADDITIONAL INFORMATION 1C REAR L/R SP 1B MAIN SP LARGE BASIC OPERATION LARGE Select this if you have large main speakers. The entire range of the left and right main channel signal is directed to the left and right main speakers. LARGE PREPARATION ■ 1B MAIN SP (main speaker mode) ■ 1C REAR L/R SP (rear speaker mode) INTRODUCTION NONE Select this if you do not have a center speaker. All of the center channel signals are directed to the left and right main speakers. LRG SML NONE SMALL y Note APPENDIX • When you select MAIN for “1D LFE/BASS OUT”, the lowfrequency signals (90 Hz and below) of the main channel are directed to the main speakers even if you select SMALL for the main speaker mode. • This unit is set in the virtual CINEMA DSP mode by selecting NONE for “1C REAR L/R SP”. English 41 SET MENU ■ 1D LFE/BASS OUT (bass out mode) ■ 1E MAIN LEVEL (main level mode) LFE signals carry low-frequency effects when this unit decodes a Dolby Digital or DTS signal. Low-frequency signals are defined as 90 Hz and below. Change this setting if you cannot match the output level of the center and rear speakers with the main speakers because of the unusually high-efficiency performance of the main speakers. Choices: SWFR (subwoofer), MAIN, BOTH Initial setting: BOTH SWFR Select this if you use a subwoofer. The LFE signals are directed to the subwoofer. 1D LFE/BASS OUT Choices: Normal, –10 dB Initial setting: Normal Normal Select this if you can match the output level of your effect speakers with that of your main speakers when using the test tone. 1E MAIN LEVEL SWFR MAIN BOTH MAIN Select this if you do not use a subwoofer. The LFE signals are directed to the main speakers. 1D LFE/BASS OUT Normal –10dB –10 dB Select this if you cannot match the output level of your effect speakers with that of your main speakers when using the test tone. 1E MAIN LEVEL SWFR MAIN BOTH BOTH Select this if you use a subwoofer and you want to mix the main channel low-frequency signals with the LFE signals. 1D LFE/BASS OUT SWFR MAIN BOTH Note • The low-frequency signals (90 Hz and below) from all main, center and rear channels are directed to the LFE channel when you select the small speaker setting in items 1A, 1B and 1C. Normal –10dB 2 LOW FRQ TEST Use this feature to adjust the output level of the subwoofer so it matches that of the other speakers in your configuration. Change the setting with the remote control while sitting in the listening position. 1 Press j / i to set “TEST TONE” to ON, and adjust the volume with VOLUME +/– so you can hear the tone. Notes • Do not turn up the volume too high. • If no test tone is heard, turn down the volume, set this unit in the standby mode and make sure all the necessary connections are correct. 42 SET MENU 2 Press d to go to “FRQ” and press j / i to select the frequency you want to use. 4 Adjust the volume of the subwoofer with the controls on the subwoofer so it matches that of the speaker you are comparing it to. ■ About the test tone Digital generator (wide band noise produced) Control range: 10 steps for L/R Initial setting: 0 Press i to decrease the output level for the left main speaker. Press j for the right main speaker. 4 HP TONE CTRL (headphone tone control) Use this feature to adjust the level of the bass and treble when you use your headphones. Control range (dB): –6 to +3 Initial setting: 0 dB for both BASS and TRBL (treble) BASIC OPERATION The test tone is produced by the tone generator. The tone generator produces a narrow-band noise centered on a specified frequency by the band pass filter. You can change this center frequency from 35 Hz through 250 Hz in one-sixth octave steps. You can use the test tone not only for adjusting the subwoofer level, but also for checking the low-frequency characteristics of your listening room. Low-frequency sounds are especially affected by the listener’s position, speaker placement, subwoofer polarity and other conditions. Use this feature to adjust the balance of the output level from the left and right main speakers. 5 CENTER GEQ (center graphic equalizer) Freq. 1 Press d to select a higher frequency and u to select a lower frequency. 2 Press j / i to adjust the level of that frequency. 35 Hz – 250 Hz y Band pass filter APPENDIX • You can monitor the center speaker sound while adjusting this item by using the test tone. Press TEST before starting the foregoing procedure. “TEST DOLBY SUR.” appears on the video monitor, and the test tone starts alternating among the speakers. Once you begin this procedure, the test tone remains at the center speaker and you can hear how the sound changes as you adjust the various frequency levels. To stop the test tone, press TEST (see pages 22 and 23). ADDITIONAL INFORMATION Control range (dB): –6 to +6 Initial setting: 0 dB for 5-band ADVANCED OPERATION Use this feature to adjust the built-in 5-band graphic equalizer so that the center speaker tonal quality matches that of the left and right main speakers. You can select the 100 Hz, 300 Hz, 1 kHz, 3 kHz, or 10 kHz frequencies. Noise Center freq. PREPARATION 3 3 L/R BALANCE (balance of the left and right main speakers) INTRODUCTION Press d to go to “OUTPUT” and press j / i to select the speaker you want to compare with the subwoofer. If SWFR is selected, the test tone above 90 Hz will not be output from the subwoofer. The test tone will not necessarily be output from the selected speakers. The output mode of the test tone depends on the settings of “1 SPEAKER SET” on the SET MENU. English 43 SET MENU 6 INPUT RENAME Use this feature to change the name of the input which appears on the OSD or the front panel display. 1 Press an input selector button (or use INPUT l / h) to select the input you want to change the name of. 2 Press j / i to place the _ (under-bar) under the space or the character you want to edit. 3 Press u/d to select the character you want to use and j / i to move to the next one. • Press d to change the character in the following order, or press u to go in the reverse order. A to Z, a space, 0 to 9, a space, a to z, a space, #, *, +, and so on. • Follow the foregoing procedure to rename other inputs. Note • You can use up to 8 characters to rename the inputs. 4 Press i repeatedly to exit from INPUT RENAME. 7 I/O ASSIGNMENT Use this feature to designate the input for the COMPONENT jacks (A and B) and the DIGITAL INPUT/OUTPUT jacks (1 to 8) to any sources you want. 8 INPUT MODE (initial input mode) Use this feature to designate the input mode for sources connected to the DIGITAL INPUT jacks when you turn on this unit (see page 26 for details about the input mode). Choices: AUTO, LAST Initial setting: AUTO AUTO Select this to allow this unit to automatically detect the type of input signal and select the appropriate input mode. LAST Select this to set this unit to automatically select the last input mode used for that source. 9 PARAM. INI (parameter initialization) Use this feature to initialize the parameters for each DSP program within a DSP program group. When you initialize a DSP program group, all of the parameter values within that group revert to their initial settings. 1 2 ■ 7A [A] [B] (for the COMPONENT VIDEO jacks) Initial settings: [A] DVD [B] D-TV/LD ■ 7B (1) (2) (for the OPTICAL OUTPUT jacks) Initial settings: (1) MD/TAPE (2) CD-R ■ 7C (3) to (6) (for the OPTICAL INPUT jacks) Initial settings: (3) CD (4) CD-R (5) DVD (6) D-TV/LD ■ 7D (7) (8) (for the COAXIAL INPUT jacks) Initial settings: (7) CD (8) CBL/SAT Note • You cannot select an item more than once for the same type of jack. 44 Press DSP. Press the numeric button (DSP program group button) on the remote control for the DSP program you want to initialize. All of the DSP programs within the selected program group are initialized. y • The asterisk mark (*) next to a DSP program group number indicates that you have changed the parameter values in one or more DSP programs within that group. Notes • You cannot initialize the individual DSP programs within a group separately. • The parameter values of the DSP programs do not change if you initialize a program group that does not have the asterisk mark (*). • When “15 MEMORY GUARD” is set to ON (see page 46), you cannot initialize any program groups. • Once you initialize a DSP program group, you cannot automatically revert to the previous parameter settings. SET MENU 10 DOLBY D. SET (Dolby Digital set) ■ 10A LFE LEVEL Control value (dB): –20 to 0 Initial setting: 0 dB for both SPEAKER and HEADPHONE Use this feature to adjust the output level of the LFE (low-frequency effect) channel when playing back a DTS signal. The LFE signal carries the low-frequency special effect sound which is only added to certain scenes. Control range (dB): –10 to +10 Initial setting: 0 dB for both SPEAKER and HEADPHONE PREPARATION Use this feature to adjust the output level of the LFE (low-frequency effect) channel when playing back a Dolby Digital signal. The LFE signal carries the lowfrequency special effect sound which is only added to certain scenes. This setting is effective only when this unit decodes DTS signals. Note • Adjust the LFE level according to the capacity of your subwoofer or headphones. Note • Adjust the LFE level according to the capacity of your subwoofer or headphones. 12 6.1/ES AUTO Use this feature to switch the auto mode of the Dolby Digital Matrix 6.1 or DTS ES decoder on or off. Use this feature to adjust the dynamic range. Dialog level ON Select this to allow this unit to automatically turn on the Dolby Digital Matrix 6.1 or DTS ES decoder when a signal with the appropriate identification is detected. OFF Select this if you want to turn on or off the Dolby Digital Matrix 6.1 or DTS ES decoder manually by pressing 6.1/ ES on the remote control. ADDITIONAL INFORMATION Output level MAX Choices: ON, OFF Initial setting: ON Input level 1.0 0.0 L-LEVEL BST Input level 1.0 Output level Dialog level MIN H-LEVEL CUT 0.0 Dialog level APPENDIX Output level STD ADVANCED OPERATION Choices: MAX, STD (standard), MIN Initial setting: MAX for both SP (speaker) and HP (headphones) • Select MAX for feature films. • Select STD for general use. • Select MIN for listening to sources at an extremely low volume level. BASIC OPERATION ■ 10B D-RANGE (dynamic range) INTRODUCTION This setting is effective only when this unit decodes Dolby Digital signals. 11 DTS LFE LEVEL Input level Note • When you select MIN, the sound output may be faint because some Dolby Digital signals are not compatible with the minimum-level dynamic range. In this case, select MAX or STD. English 45 SET MENU 13 SP DELAY TIME 14 DISPLAY SET Use this feature to adjust the delay of the center channel sound. This feature works when this unit decodes a Dolby Digital or DTS signal. Ideally, the center speaker should be the same distance from the listening position as the left and right main speakers. However, in most home situations, the center speaker is placed in line with the main speakers. By delaying the sound from the center speaker, the apparent distance from the center speaker to the listening position can be adjusted to make it seem the same as the distance between the left and right main speakers to the listening position. Adjusting the delay time for the center speaker is especially important for giving depth to the dialog. Center speaker image C C You can set the OSD background to blue if the video source is not being reproduced (or the power of the source component is off). ■ OSD SHIFT (OSD off-set position) This setting is used to adjust the vertical position of the OSD. ■ DIMMER You can adjust the brightness of the front panel display. 15 MEMORY GUARD Control range (ms): 0 to 5 L ■ BLUE BACK > AUTO/OFF R Use this feature to prevent accidental changes to DSP program parameter values and other settings on this unit. Choices: ON, OFF Initial setting: OFF Select ON to protect the following features: • DSP program parameters • All SET MENU items • Center, rear speakers and subwoofer levels • The on-screen display (OSD) mode RL RR y • Increasing the delay by 1 ms simulates moving the speakers about 30 cm (one foot) farther away from the listening position. 46 Notes • When “15 MEMORY GUARD” is set to ON, you cannot use the test tone. • When “15 MEMORY GUARD” is set to ON, you cannot select any other SET MENU items. ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS Adjustment should be made with the remote control. 3 Press j / i to adjust the speaker output level. • The control range for the center or left and right rear speakers is from +10 dB to –10 dB. • The control range for the subwoofer is from 0 dB to –20 dB. 3 1 Notes • If the speaker output mode is set to NONE, the output level of that speaker cannot be adjusted. • When you adjust the output level with LEVEL, the settings you made with the test tone will be changed. 2 Press LEVEL repeatedly to select the speaker(s) you want to adjust. Each time you press LEVEL, the selected speaker changes and appears on the front panel display and on the video monitor as follows: center, right rear, left rear and subwoofer. ADVANCED OPERATION Set the selector dial to the AMP/TUN (or DSP/TUN) position. BASIC OPERAIONT 1 Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the output level of the effect speakers you adjusted will return to the factory settings. If so, adjust the output level again. PREPARATION 2 INTRODUCTION You can adjust the output level of each effect speaker (center, left and right rear and subwoofer) while listening to a music source. ADDITIONAL INFORMATION Center speaker output level Right rear speaker output level Left rear speaker output level Subwoofer output level APPENDIX y • Once you press LEVEL, you can also select the speaker(s) to be adjusted by pressing d. (Pressing u changes the selection in the reverse order.) English 47 SLEEP TIMER Use this feature to automatically set this unit in the standby mode after the amount of time you have set. The sleep timer is useful when you are going to sleep while this unit is playing or recording a source. The sleep timer also automatically turns off the external components connected to AC OUTLET(S). 4 The “SLEEP” indicator soon lights up on the front panel display after the sleep timer has been set. The display then returns to the previous indication. VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB The sleep timer can only be set with the remote control. PS PTY RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED VOLUME dB ms D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO y • By connecting a commercially available timer to this unit, you can also set a wake-up timer. Refer to the operation instructions of the timer. Canceling the Sleep Timer Press SLEEP repeatedly until “SLEEP OFF” appears on the front panel display. After a few seconds, “SLEEP OFF” disappears, the “SLEEP” indicator goes off and the display returns to the previous indication. Setting the Sleep Timer 2 y • The sleep timer setting can also be canceled by setting this unit in the standby mode by using STANDBY on the remote control (or STANDBY/ON on the front panel) or by disconnecting the AC power cord from the AC outlet. 3 1 Select a source and start playback on the source component. 2 Set the selector dial to a position other than the TV position. 3 Press SLEEP repeatedly to set the amount of time before this unit automatically turns off. Each time you press SLEEP, the front panel display changes as shown below. VIRTUAL DIGITAL PRO LOGIC DSP 6.1/ES SP PCM AB 48 PS PTY RT CT DTS MOVIE THEATER 1 2 PTY HOLD EON STEREO AUTO DOLBY DIGITAL ZONE 2 NEWS INFO AFFAIRS SPORT SLEEP PRO LOGIC ENTERTAINMENT MEMORY TUNED VOLUME dB ms D-TV/LD CBL/SAT VCR 1 VCR2/DVR V-AUX DVD MD/TAPE CD-R TUNER CD PHONO REMOTE CONTROL FEATURES This remote control also has a sophisticated feature: Learn. The Learn feature allows it to acquire functions from the remote controls of other components in your system (or other household appliances) equipped with a infrared remote control receiver. This feature makes it possible for you to reduce the number of remote control in your entertainment room. INTRODUCTION The remote control can operate this unit as well as other YAMAHA A/V components. To control the components from other manufacturers (or some from YAMAHA), you must set up the remote control with the manufacturer codes. Notes Selector Dial AMP/TUN You can perform the basic operations of this unit. See pages 6 and 7. TAPE/MD The code for a YAMAHA tape deck is factoryset. Be sure to set the proper code when operating an MD recorder or CD recorder. CD The code for a YAMAHA CD player is factory-set. VCR A VCR can be controlled. TV A TV can be controlled. Selector dial DVD/LD & DVD MENU An LD player can be controlled in the DVD/LD position. A DVD player can be controlled in the DVD/LD and DVD MENU positions. The code for a YAMAHA DVD player is factoryset. If the remote control does not operate your YAMAHA DVD player, you need to set the code number “0048”. Note • The general operational buttons on the remote control differ depending on the position of the selector dial. See the following pages for details. ADDITIONAL INFORMATION DSP/TUN This unit can be controlled and DSP programs can be selected directly. ADVANCED OPERATION CBL/SAT A cable TV or satellite tuner can be controlled. BASIC OPERAIONT There are 9 positions that you can select to control connected components with this remote control. For example, if the CD position is selected, the remote control is set in the CD operation mode, allowing the CD player to be controlled by the buttons on the remote control. When turning the selector dial, the position changes as follows: PREPARATION • For the operating distance of the remote contorol and notes about batteries, see pages 3 and 8. • For the name and function of each part and button, see pages 6 to 8. • If the memory on the remote control becomes full, no further learning is possible, even if there are still some programmable buttons available (see page 55). APPENDIX English 49 REMOTE CONTROL FEATURES Commonly Used Buttons in Any Position of the Selector Dial Regardless of the position of the selector dial, you can control this unit and your TV with the following buttons. Controlling the Components Connected to This Unit The example below describes the procedure for controlling a YAMAHA CD player. Note 1 • You have to set up the code for your TV in the TV position before you can control the TV. 3 4 1 ! @ 2 # 3 4 5 ■ Controlling this unit 1 Set the selector dial to the CD position. 2 Turn on the power. 3 Press INPUT. The indicator lights up for about 3 second. 4 Press CD while the indicator is lit. 5 Press p. See page 51 for the CD player operation buttons. 6 Adjust the volume. See pages 6 and 7. 1 2 3 4 STANDBY POWER VOLUME +/– SLEEP Note • If you have set up the code for your TV and set the selector dial to the TV position, this button is used to set the sleep timer for the TV. 5 MUTE 5 2 6 Note • If you have set up the code for your TV and set the selector dial to the TV position, this button is used to mute the TV sound. ■ Controlling your TV ! TV POWER @ TV INPUT # TV VOLUME +/– 50 If you set the remote control with the manufacturer codes listed from page i at the end of this manual, you can control other brands of components. See “Setting the Manufacturer Codes” on page 54 for details. REMOTE CONTROL FEATURES Button Names and Functions in Each Position INTRODUCTION ■ TAPE/MD position (tape deck, MD recorder or CD recorder) Select the TAPE/MD position. Numeric buttons (MD/CD-R) PREPARATION INDEX (CD-R) +10 (MD/CD-R) r Rec/Pause (tape/MD) e Pause (MD/CD-R) p Play A/B/C/D/E f Fast forward (tape) Search (MD/CD-R) w Rewind (tape) Search (MD/CD-R) AV POWER (Tape) This button turns on the tape deck that has a remote control with a power button if you have set up the code for another manufacturer. (MD) This button turns on the MD recorder that has a remote control with a power button if you have set up the code for another manufacturer. (CD-R) This button turns on the CD recorder that has a remote control with a power button if you have set up the code for another manufacturer. ADVANCED OPERATION ■ CD position BASIC OPERAIONT b DIR A (tape) This button selects the playing direction of deck A. Skip – (MD/CD-R) Deck A/B (tape) This button selects deck A or B on a double-cassette tape deck. DISPLAY (MD/CD-R) a DIR B (tape) This button selects the playing direction of deck B. Skip + (MD/CD-R) s Stop Select the CD position. p Play b Skip – DISPLAY • Press the button once to give a pause in operation and press once more to stop operation. e Pause YAMAHA CD player (factory settings): Pause/Stop a Skip + s Stop YAMAHA CD player (factory settings): Pause/Stop f Search APPENDIX w Search A/B/C/D/E y Pause/Stop function ADDITIONAL INFORMATION DISC SKIP –/+ (for a CD player with CD changer) Numeric buttons INDEX +10 AV POWER This button turns on the CD player that has a remote control with a power button if you have set up the code for another manufacturer. Notes You can program a remote control function to all buttons except DSP and INPUT. See “Programming a New Remote Control Function” on page 55. 51 English • The dark-shaded buttons do not function even if you have set up the manufacturer code. • Some of them may not function depending on the component you have. Refer to the operation instructions for your component. REMOTE CONTROL FEATURES ■ DVD/LD position Select the DVD/LD position. Numeric buttons INDEX/Time (DVD) Chapter/Time (LD) +10 DISC SKIP –/+ (DVD) DISPLAY p Play A/B/C/D/E b Skip – (DVD) Skip/Chapter – (LD) w Search e Pause a Skip + (DVD) Skip/Chapter + (LD) s Stop f Search AV POWER (DVD) This button turns on the YAMAHA DVD player if you have set up the code number “0048”. Also this button turns on the DVD player that has a remote control with a power button if you have set up the code for another manufacturer. (LD) This button turns on the LD player that has a remote control with a power button if you have set up the code for another manufacturer. ■ DVD MENU position Note • DVD MENU operations cannot be performed for some DVD players. Select the DVD MENU position. Numeric buttons INDEX +10 DISC SKIP –/+ Return Menu select Menu left TITLE DISPLAY A/B/C/D/E Menu up Menu right Menu down MENU AV POWER This button turns on the YAMAHA DVD player if you have set up the code number “0048”. Also this button turns on the DVD player that has a remote control with a power button if you have set up the code for another manufacturer. Notes • The dark-shaded buttons do not function even if you have set up the manufacturer code. • Some of them may not function depending on the component you have. Refer to the operation instructions for your component. You can program a remote control function to all buttons except DSP and INPUT. See “Programming a New Remote Control Function” on page 55. 52 REMOTE CONTROL FEATURES ■ VCR position ■ CBL/SAT position Select the CBL/SAT position. VCR REC Press this button twice to start recording. A/B/C/D/E Numeric buttons Ch enter/Recall Ch enter _/_ _ _/_ _ CH –/+ DISPLAY CH –/+ e Pause Menu select s Stop w Rewind f Fast forward DISPLAY/ Guide (SAT) A/B/C/D/E Menu up Menu right Menu down MENU Menu left Recall AV POWER This button turns on a cable TV/satellite tuner that has a remote control with a power button if you have set up the code for your cable TV/satellite tuner. ■ TV position BASIC OPERAIONT AV POWER This button turns on a VCR that has a remote control with a power button if you have set up the code for your VCR. PREPARATION p Play Numeric buttons INTRODUCTION Select the VCR position. Note Select the TV position. Numeric buttons Ch enter/Recall VCR REC Press this button twice. ADDITIONAL INFORMATION _/_ _ CH –/+ DISPLAY p VCR play A/B/C/D/E e VCR pause s VCR stop w VCR rewind TV INPUT f VCR fast forward VCR power APPENDIX TV POWER This button turns on a TV that has a remote control with a power button if you have set up TV VOL +/– the code for your TV. ADVANCED OPERATION • You can control your VCR if you have set up the code for it in the VCR position. TV SLEEP TV MUTE Notes You can program a remote control function to all buttons except DSP and INPUT. See “Programming a New Remote Control Function” on page 55. 53 English • The dark-shaded buttons do not function even if you have set up the manufacturer code. • Some of them may not function depending on the component you have. Refer to the operation instructions for your component. REMOTE CONTROL FEATURES Setting the Manufacturer Code You can set up the code for the manufacturer of your component in each position of the selector dial. 1 2 3 4 5 Turn on your component to be used. Set the selector dial to the desired position for the component (TAPE/MD, CD, DVD/LD, etc.). Press j / i at the same time for about 4 seconds. The indicator flashes twice. Use the numeric buttons to enter the four-digit manufacturer code for the component to be used. Make sure that the indicator flashes twice. If the indicator does not flash or flashes rapidly several times, repeat step 3 and reenter the code. Press AV POWER (or any other button) to check if you have set up the code correctly. If your component cannot be controlled with the remote control, try setting another code for the same manufacturer. Notes • You can set up only one code for one position. • In the DVD/LD and DVD MENU positions: Be sure to set the selector dial to the DVD/LD position before entering the code for the DVD/LD player. The code set up in the DVD/LD position is also simultaneously set up in the DVD MENU position. You cannot set up the code for a DVD player when the selector dial is set to the DVD MENU position. • If your component does not respond to any of the codes listed for the manufacturer, you can program functions from the other remote control’s functions (see page 55 for details). • If you have already programmed a remote control function to a button, the function by programming (see page 55) takes priority over the set up manufacturer code’s function. 54 ■ To use a second (and third) VCR You can control a second (and third) VCR in the CBL/ SAT and DVD MENU positions if a cable TV/satellite tuner or DVD player is not being used. Note • If you want to control a second (and third) VCR in the DVD MENU position, you must set up the code for an LD player in the DVD/LD position. 1 2 Turn on the VCR to be used. 3 Press j / i at the same time for about 4 seconds. The indicator flashes twice. 4 Use the numeric buttons to enter the four-digit code for the second (and third) VCR. Make sure that the indicator flashes twice. If the indicator does not flash or flashes rapidly several times, repeat step 3 and reenter the code. 5 Press AV POWER (or any other button) to check if you have set up the code correctly. If the VCR cannot be controlled with the remote control, try setting another code for the same manufacturer. Set the selector dial to the CBL/SAT or DVD MENU position. REMOTE CONTROL FEATURES Programming a New Remote Control Function (Learn Feature) Press the button for which you want to program the new function. The indicator lights up. INTRODUCTION If you want to program functions not included in the basic operations covered by the manufacturer code, or a manufacturer code is not available, the following procedure needs to be performed. You can program functions to all buttons except DSP and INPUT in all positions of the selector dial other than AMP/TUN and DSP/TUN, so the buttons are programmable independently for each position of the selector dial. 4 Lights up 5 • You can program about 60 buttons. PREPARATION y Press and hold the button on the other remote control that has the function you want to program into this remote control until the indicator goes off. Note Set the selector dial to the desired position for the component to be programmed. 2 Place this remote control and the other remote control about 10 to 40 mm (3/8” to 1-1/2”) apart on a flat surface so that their infrared transmitters are aimed at each other. 3 Press and hold e and p at the same time for about 4 seconds. The indicator flashes twice. 6 Repeat steps 4 and 5 to program additional functions. 7 Press DSP or INPUT, or turn the selector dial to exit from the learning mode. The indicator flashes twice. Notes • Even if the batteries in the other remote control have enough power to transmit signals for operation, they may not have enough power to transmit signals to this remote control. • When the remote controls are either too close together or too far apart, you may not be able to program this remote control. • Direct sunlight interferes with infrared rays. Memory back-up If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the manufacturer code and program any acquired functions that may have been cleared. APPENDIX Note • If you do not press any button within 30 seconds during steps 4 and 5, the indicator flashes twice and the learning process is canceled. If this happens, start over from step 3. • If this remote control cannot receive the signals from other remote control, the indicator flashes rapidly. • When the memory is full, the indicator flashes twice and this remote control cannot acquire any more functions. Clear unnecessary programmed functions to allow this remote control to acquire new functions. • If you do not press any button within 30 seconds after step 5, the indicator flashes twice. This indicates that the learning process is complete and the remote control has exited from the learning mode. ADDITIONAL INFORMATION 10 to 40 mm (3/8” to 1-1/2”) Notes ADVANCED OPERATION 1 Goes off BASIC OPERAIONT • This remote control transmits infrared rays. If the other remote control also uses infrared rays, this remote control can learn most of the other remote control’s functions. However, you may not be able to program some special signals or extremely long transmissions. (Refer to the operation instructions for the other remote control.) English 55 REMOTE CONTROL FEATURES Returning to the Factory Setting ■ To return to the factory-set codes and to clear the learned functions in all positions 1 2 Press j / i at the same time for about 4 seconds. The indicator flashes twice. ■ To return to the factory-set codes and to clear the learned functions in each position 1 Set the selector dial to the position for the component to be returned to the factory setting. 2 Press j / i at the same time for about 4 seconds. The indicator flashes twice. 3 Enter the code number “0000”. Make sure that the indicator flashes twice. Enter the code number “9990”. Make sure that the indicator flashes twice. The following codes are factory set. Selector dial position TV CBL/SAT VCR DVD/LD TV Satellite tuner VCR DVD player CD CD player TAPE/MD Tape deck AMP/TUN DSP/TUN this unit this unit Component Code 0101 0006 0002 0008 (YAMAHA DVD player) 0005 (YAMAHA CD player) 0004 (YAMAHA Tape deck) 0003 0013 We recommend that you write all the code numbers you have set on the “Quick Reference Card”. 56 ADDITIONAL INFORMATION SOUND FIELD PROGRAM The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. INTRODUCTION This unit incorporates a sophisticated, multi-program digital sound field processor (DSP). This processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in your listening room. You can create outstanding audio sound field by selecting a suitable DSP program (this will, of course, depend on what you are listening to) and making desired adjustments. Note PREPARATION • Select the DSP program that you feel sounds best regardless of the name and description given for it below. Hi-Fi DSP Programs ■ For audio sources: Nos. 1 to 5 No. Program (group) Sub-program Features — A large round concert hall with a rich surround effect. Pronounced reflections from all directions emphasize the extension of sounds. The sound field has a great deal of presence, and your virtual seat is near the center, close to the stage. 2 CHURCH — This program recreates the acoustic environment of a big church with a high dome and columns along each side. The reverberation delay is very long while the early reflections are smaller than with other sound field programs. 3 JAZZ CLUB — This is the sound field at stage front in “The Bottom Line”, a famous New York jazz club. The floor can seat 300 people to the left and right in a sound field offering a real and vibrant sound. 4 ROCK CONCERT — The ideal program for lively, dynamic rock music. The data for this program was recorded at LA’s “hottest” rock club. The listener’s virtual seat is at the center-left of the hall. 5 ENTERTAINMENT This program recreates the acoustic environment of a lively disco in the heart of a big city. The sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate” sound. 5ch Stereo Using this program increases the listening position range. This is a sound field suitable for background music at parties. ADDITIONAL INFORMATION Disco ADVANCED OPERATION CONCERT HALL BASIC OPERATION 1 Note • If “1A CENTER SP” on the SET MENU is set to NONE, no sound is output from the center speaker. APPENDIX English 57 SOUND FIELD PROGRAM CINEMA DSP Programs ■ For audio-video sources: Nos. 5 to 7 No. Program (group) Sub-program Game Features This program adds a deep and spatial feeling to video game sounds. 5 ENTERTAINMENT 6 TV SPORTS — Although the presence sound field is relatively narrow, the surround sound field employs the sound environment of a large concert hall. With this program, you can enjoy watching various TV programs such as news, variety shows, music programs or sports programs. In a stereo broadcast of a sports game, the commentator is oriented at the center position, and the shouts and the atmosphere in the stadium spread on the surround side, while their spread to the rear is properly restrained. 7 MONO MOVIE — This program is provided for reproducing monaural video sources (such as old movies). The program produces the optimum reverberation to create sound depth by using only the presence sound field. ■ For movie programs: Nos. 8 to 10 No. 8 Program (group) Sub-program MOVIE Spectacle 70 mm Spectacle THEATER 1 DGTL Spectacle *1 Spectacle 6.1 *2 DTS Spectacle *1 Input source Features Analog, PCM, Dolby Digital in 2-channel This program creates the extremely wide sound field of a 70-mm movie theater. It precisely reproduces the source sound in detail, making both the video and the sound field incredibly real. This is ideal for any kind of video source encoded with Dolby Surround, Dolby Digital or DTS (especially large-scale movie productions). Dolby Digital DTS Spectacle ES *2 Sci-Fi 70 mm Sci-Fi Analog, PCM, Dolby Digital in 2-channel DGTL Sci-Fi *1 Dolby Digital Sci-Fi 6.1 *2 DTS Sci-Fi *1 Sci-Fi ES *2 58 DTS This program clearly reproduces dialog and sound effects in the latest sound form of science fiction films, thus creating a broad and expansive cinematic space amid the silence. You can enjoy science fiction films in a virtual-space sound field that includes Dolby Surround, Dolby Digital and DTS-encoded software employing the most advanced techniques. SOUND FIELD PROGRAM No. 9 Program (group) Sub-program Input source DGTL Adventure *1 Adventure 6.1 *2 DTS Adventure *1 Analog, PCM, Dolby Digital in 2-channel Dolby Digital This program is ideal for precisely reproducing the sound design of the newest 70-mm and multichannel soundtrack films. The sound field is made to be similar to that of the newest movie theaters, so the reverberations of the sound field itself are restrained as much as possible. DTS INTRODUCTION MOVIE Adventure 70 mm Adventure THEATER 2 Features Adventure ES *2 70 mm General Analog, PCM, Dolby Digital in 2-channel DGTL General *1 Dolby Digital General 6.1 * 2 DTS This program is for reproducing sounds from 70-mm and multichannel soundtrack films, and is characterized by a soft and extensive sound field. The presence sound field is relatively narrow. It spatially spreads all around and toward the screen, restraining the echo effect of conversations without losing clarity. For the surround sound field, the harmony of music or chorus sounds beautifully in a wide space at the rear of the sound field. BASIC OPERATION DTS General *1 PREPARATION General General ES *2 ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 59 SOUND FIELD PROGRAM No. Program (group) Sub-program Normal/ 10 q/DTS SURROUND Matrix 6.1/ES Input source PRO LOGIC/Normal Analog, PCM, Dolby Digital in 2-channel DOLBY DIGITAL/ Normal *1 Dolby Digital DOLBY DIGITAL/ Matrix 6.1 *2 DTS DIGITAL SUR./ Normal *1 Features The built-in decoder precisely reproduces sounds and sound effects from sources. The highly efficient decoding process improves crosstalk and channel separation, and makes sound positioning smoother and more precise. In this program, the digital sound field processor is not turned on. DTS DTS DIGITAL SUR./ ES *2 Enhanced PRO LOGIC/Enhanced DOLBY DIGITAL/ Enhanced *1 Analog, PCM, Dolby Digital in 2-channel Dolby Digital DOLBY DIGITAL/ Enhanced 6.1 *2 DTS DIGITAL SUR./ Enhanced *1 This program ideally simulates the multi-surround speaker systems of the 35-mm film theaters. Dolby Pro Logic decoding, Dolby Digital decoding or DTS decoding and digital sound field processing create precise effects without altering the original sound orientation. The surround effects produced by this sound field wrap around the viewer naturally from the back to the left and right, and toward the screen. DTS DTS DIGITAL SUR./ Enhanced ES *2 *1 The Dolby Digital Matrix 6.1 or DTS ES decoder is off. *2 The Dolby Digital Matrix 6.1 or DTS ES decoder is on. The “ c ” indicator lights up on the front panel display. y • If a Dolby Digital signal or DTS signal is input when the input mode is set to AUTO, the DSP program will be automatically switched to the Dolby Digital playback sound field or DTS playback sound field. • If Dolby Digital Surround EX software or DTS ES software is played when “12 6.1/ES AUTO” on the SET MENU is set to ON, the Dolby Digital Matrix 6.1 or DTS ES decoder will automatically turn on and the corresponding DSP program will be selected. • 6.1/ES on the remote control can be used to turn the Dolby Digital Matrix 6.1 or DTS ES decoder on or off during Dolby Digital 5.1channel source or DTS 5.1-channel source playback. Notes • The “ x ” indicator does not light up when selecting the sub-program “Normal” of the q/DTS SURROUND program. • If “1A CENTER SP” on the SET MENU is set to NONE, no sound is output from the center speaker. • The effect sound is output from the main speakers when a monaural source is played with CINEMA DSP program groups 5 (Game) and 6 to 9. 60 SOUND FIELD PROGRAM MOVIE THEATER Programs ■ Dolby Pro Logic + DSP sound field effect These programs express an immense sound field and a large surround effect. They also give depth to the sound from the main speakers to recreate the realistic sound of a Dolby Stereo theater. Presence DSP sound field BASIC OPERATION Surround DSP sound field ■ Dolby Digital/DTS + DSP sound field effect Right surround DSP sound field ADDITIONAL INFORMATION Left surround DSP sound field ADVANCED OPERATION These programs use YAMAHA’s tri-field DSP processing on each of the Dolby Digital or DTS signals for the front, left surround and right surround channels. This processing enables this unit to reproduce the immense sound field and surround expression of a Dolby Digital- or DTSequipped movie theater without sacrificing the clear separation of all channels. Presence DSP sound field PREPARATION The 6-channel soundtracks found on 70-mm film produce precise sound field localization and rich, deep sound without using matrix processing. This unit’s MOVIE THEATER 70 mm programs provide the same quality of sound and sound localization that 6-channel soundtracks do. The built-in Dolby Digital or DTS decoder brings the professional-quality sound designed for movie theaters into your home. With the unit’s MOVIE THEATER programs, you can recreate a dynamic sound that gives you the feeling of being at a public theater in your listening room by using Dolby Digital or DTS technology. INTRODUCTION Most movie software has 4-channel (left, center, right and surround) sound information encoded by Dolby Surround matrix processing and stored on the left and right tracks. These signals are processed by the Dolby Pro Logic decoder. The MOVIE THEATER programs are designed to recreate the spaciousness and delicate nuances of sound that tend to be lost in the encoding and decoding processes. APPENDIX English 61 SOUND FIELD PROGRAM PARAMETER EDITING What is a sound field? What really creates the rich, full tones of a live instrument are the multiple reflections from the walls of the room. In addition to making the sound “live”, these reflections enable us to tell where the player is situated, and the size and shape of the room in which we are sitting. ■ Elements of a sound field In any environment, in addition to the direct sound coming straight to our ears from the player’s instrument, there are two distinct types of sound reflections that combine to make up the sound field: Early reflections Reflected sounds reach our ears extremely rapidly (50 ms – 100 ms after the direct sound), after reflecting from one surface only — for example, from the ceiling or a wall. These reflections fall into specific patterns as shown in the diagram on page 64 for any particular environment, and provide vital information to our ears. Early reflections actually add clarity to the direct sound. Reverberations These are caused by reflections from more than one surface — walls, ceiling, the back of the room — so numerous that they merge together to form a continuous sonic “afterglow”. They are non-directional, and lessen the clarity of the direct sound. Direct sound, early reflections and subsequent reverberation taken together help us to determine the subjective size and shape of the room, and it is this information that the digital sound field processor reproduces in order to create sound fields. If you could create the appropriate early reflections and subsequent reverberations in your listening room, you would be able to create your own listening environment. The acoustics in your room could be changed to those of a concert hall, a dance floor, or virtually any size room at all. This ability to create sound fields at will is exactly what YAMAHA has done with the digital sound field processor. 62 Sound Field Program Parameters DSP programs consist of some parameters to determine the apparent room size, reverberation time, distance from you to the performer, etc. In each program, these parameters are set with values precisely calculated by YAMAHA to create a sound field unique to the program. It is recommended to use DSP programs without changing the values of parameters; however, this unit also allows you to create your own sound fields. Starting with one of the built-in programs, you can adjust those parameters. Each DSP program has a set of parameters that allow you to change the characteristics of the acoustic environment to precisely create the effect you want. These parameters correspond to the many natural acoustic factors that create the sound field you experience in an actual concert hall or other listening environment. The size of the room, for example, affects the length of time between the early reflections. The “ROOM SIZE” parameter provided in many of the DSP programs alters the timing between these reflections, thus changing the shape of the “room” you are listening. In addition to room size, the shape of the room and the characteristics of its surfaces have a significant effect on the final sound. Surfaces that absorb sound, for example, cause the reflections and reverberations to die out more quickly, while highly reflective surfaces allow the reflections to carry on for a longer period of time. The digital sound field parameters allow you to control these and many other factors that contribute to your personal sound field, allowing you to essentially “redesign” the concert halls, theaters, etc. provided to create custom-tailored listening environments that ideally match your mood and music. See “Digital Sound Field Parameter Descriptions” on pages 64 to 67. SOUND FIELD PROGRAM PARAMETER EDITING Changing Parameter Settings Press u/d to select the parameter. 5 Press j / i to change the parameter value. Adjustments should be made with the remote control. INTRODUCTION You can enjoy good quality sound with the factory-set parameters. Although you do not have to change the initial settings, you can change some of the parameters to better suit the input source or your listening room. 4 y • We recommend that you edit the parameter while using a video monitor. It is easier to see the video monitor than it is to see the front panel display. 3 Set the selector dial to the DSP/TUN (or AMP/TUN) position. or 3 Turn on the video monitor and press ON SCREEN repeatedly to select the full display mode. Select a DSP program you want to adjust. Repeat steps 3 to 5 above as necessary to change other program parameters. Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the parameter value you edited will return to the factory setting. If so, edit the parameter value again. Resetting a Parameter to the Factory-set Value ■ To reset some of the parameters to the factory-set values ■ To reset all of the parameters to the factory-set values P04 ROCK CONCERT Cursor INIT.DLY LIVENESS REV.TIME REV.DELAY REV.LEVEL 15ms 5 1.6s 100ms 7% Example of the ROCK CONCERT 63 English Parameters Notes • The available parameters may be displayed on more than one OSD page for some of the programs. To scroll through pages, press u/d. • You cannot change parameter values when “15 MEMORY GUARD” on the SET MENU is set to ON. If you want to change the parameter values, set “15 MEMORY GUARD” to OFF (see page 46). APPENDIX Program No. Program name (group) Use “9 PARAM. INI” on the SET MENU to reset all of the parameter values of all DSP programs within the selected group to the factory-set values (see page 44). This operation resets all of the parameter values of all DSP programs within that group to the factory-set values. ADDITIONAL INFORMATION Select the parameter you want to reset. Then press and hold j or i until the value temporarily stops at the factory-set value. The asterisk mark (*) by the parameter name disappears on the video monitor. ADVANCED OPERATION 2 6 BASIC OPERATION 1 • When you set the parameter to a value other than the factoryset value, an asterisk mark (*) appears by the parameter name on the video monitor. PREPARATION 2 4 5 3 1 y SOUND FIELD PROGRAM PARAMETER EDITING Digital Sound Field Parameter Descriptions You can adjust the values of certain digital sound field parameters so the sound fields are recreated accurately in your listening room. Note • Not all of the following parameters can be found in every program. ■ INIT.DLY (initial delay) (P.INIT.DLY — for the presence sound field) Function: This parameter changes the apparent distance from the sound source by adjusting the delay between the direct sound and the first reflection heard by the listener. Control range: 1 – 99 msec Description: The smaller the value, the closer the sound source seems to the listener. The larger the value, the farther the apparent distance seems. For a small room, this parameter would be set to a small value, for a large room, set it to a large value. Sound source First reflection Time Level Level Level Early reflections Time Time INT. DLY INT. DLY INT. DLY Sound source Reflection surface Large value = 99 ms Small value = 1 ms ■ ROOM SIZE (P.ROOM SIZE — for the presence sound field) Function: This parameter adjusts the apparent size of the surround sound field. The larger the value, the larger the surround sound field becomes. Control range: 0.1 – 2.0 Description: As the sound is repeatedly reflected around a room, the larger the hall is, the longer the time between the original reflected sound and the subsequent reflections. By controlling the time between the reflected sounds, you can change the apparent size of the virtual venue. Changing this parameter from one to two, doubles the apparent length of the room. Level Level Level Sound source Early reflections Time Time Time Sound source Small value = 0.1 64 Large value = 2.0 SOUND FIELD PROGRAM PARAMETER EDITING ■ LIVENESS Function: Sound source INTRODUCTION This parameter adjusts the reflectivity of the virtual walls in the hall by changing the rate at which the early reflections decay. Control range: 0 – 10 Description: The early reflections of a sound source decay much faster in a room with acoustically absorbent wall surfaces than in one which has highly reflective surfaces. A room with acoustically absorbent surfaces is referred to as “dead,” while a room with highly reflective surfaces is referred to as “live.” The “LIVENESS” parameter lets you adjust the early reflection decay rate, and thus the “liveness” of the room. Level Level Dead Time Time Small reflected sound Time Large reflected sound BASIC OPERATION Sound source Small value = 0 PREPARATION Level Live Large value = 10 ■ S.DELAY (surround delay) Function: ■ S.INIT.DLY (surround initial delay) Function: This parameter adjusts the delay between the direct sound and the first reflection on the surround side of the sound field. You can only adjust this parameter when at least two front channels and two rear channels are used. Control range: 1 – 49 msec ADVANCED OPERATION This parameter adjusts the delay between the direct sound and the first reflection in the surround sound field. Control range: 0 – 49 msec (The range depends on the signal format.) ADDITIONAL INFORMATION ■ S.ROOM SIZE (surround room size) Function: This parameter adjusts the apparent size of the surround sound field. Control range: 0.1 – 2.0 ■ S.LIVENESS (surround liveness) Function: This parameter adjusts the apparent reflectivity of the virtual walls in the surround sound field. Control range: 0 – 10 APPENDIX English 65 SOUND FIELD PROGRAM PARAMETER EDITING ■ RC.INIT.DLY (rear center initial delay) Function: This parameter adjusts the delay between the direct sound and the first reflection in the rear center sound field. Control range: 1 – 49 msec ■ RC.ROOM SIZE (rear center room size) Function: This parameter adjusts the apparent size of the rear center sound field. Control range: 0.1 – 2.0 ■ RC.LIVENESS (rear center liveness) Function: This parameter adjusts the apparent reflectivity of the virtual wall in the rear center sound field. Control range: 0 – 10 ■ REV.TIME (reverberation time) Function: This parameter adjusts the amount of time it takes for the dense, subsequent reverberation sound to decay by 60 dB (at 1 kHz). This changes the apparent size of the acoustic environment over an extremely wide range. Control range: 1.0 – 5.0 sec Description: Set a longer reverberation time for “dead” sources and listening room environments and a shorter time for “live” sources and listening room environments. Sound source Early reflections Reverberations Time REV. TIME Short reverberations Reverberations Level 60 dB Level Level Reverberations 60 dB 60 dB Time Time REV. TIME REV. TIME Long reverberations Sound source Small value = 1.0 s 66 Large value = 5.0 s SOUND FIELD PROGRAM PARAMETER EDITING ■ REV.DELAY (reverberation delay) Reverberation Sound source INTRODUCTION This parameter adjusts the time difference between the beginning of the direct sound and the beginning of the reverberation sound. Control range: 0 – 250 msec Description: The larger the value, the later the reverberation sound begins. A later reverberation sound makes you feel like you are in the larger acoustic environment. Level Function: (dB) PREPARATION 60 dB Time REV. DELAY REV TIME ■ REV.LEVEL (reverberation level) Level BASIC OPERATION Function: This parameter adjusts the volume of the reverberation sound. Control range: 0 – 100% Description: The larger the value, the stronger the reverberation becomes. Sound source REV. LEVEL ADVANCED OPERATION Time ■ CT.DELAY (center delay) ADDITIONAL INFORMATION ■ LS.DELAY (left surround delay) ■ RS.DELAY (right surround delay) Function: These parameters adjust the sound delay for each channel in 5 channel stereo mode. Control range: 0 – 50 msec APPENDIX English 67 APPENDIX TROUBLESHOOTING Refer to the chart below when the unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit in the standby mode, disconnect the power cord and contact the nearest authorized YAMAHA dealer or service center. ■ General Problem The unit fails to turn on when STANDBY/ON (or POWER) is pressed, or enters in the standby mode soon after the power has been turned on. No sound and/or no picture. Cause Remedy Refer to page The power cord is not connected or the plug is not completely inserted. Firmly connect the power cord. 19 The IMPEDANCE SELECTOR switch on the rear panel is not fully set to the left or right position. Set the switch fully to the left or right position when the unit is in the standby mode. 19 The protection circuitry has been activated. Make sure all speaker wire connections on this unit and on all speakers are secure and that the wire for each connection does not touch anything other than its respective connection. 16, 17 Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables may be defective. 12 – 15 An appropriate input source has not been selected. Select an appropriate input source with INPUT l / h or 6CH INPUT (or the input selector buttons). 24 16, 17 The speaker connections are not secure. Secure the connections. The main speakers to be used have not been selected properly. Select the main speakers with SPEAKERS A and/or B. The volume is turned down. Turn up the volume. 25 The sound is muted. Press MUTE or any operation buttons of this unit to cancel a mute and adjust the volume. 25 Digital signals other than PCM audio, Dolby Digital or DTS signal which this unit cannot reproduce are being input to this unit by playing a CD-ROM, etc. Play a source whose signals this unit can reproduce. — No picture. There is no S-video connection between this unit and the video monitor, although Svideo signals are being input to this unit. Connect the monitor’s S-video input jack to this unit’s S VIDEO MONITOR OUT jack. The sound suddenly goes off. The protection circuit has been activated because of a short circuit, etc. Check the IMPEDANCE SELECTOR switch is set to the appropriate position and then turn the unit back on. Check the speaker wires are not touching each other and then turn the unit back on. Only the speaker on one side can be heard. 68 24 14, 15 19 16, 17 The sleep timer has functioned. Turn on the power, and play the source again. 48 The sound is muted. Press MUTE or any operation buttons of this unit to cancel a mute and adjust the volume. 25 Incorrect cable connections. Connect the cables properly. If the problem persists, the cables may be defective. Incorrect setting of “3 L/R BALANCE” on the SET MENU. Adjust it to the appropriate position. 12 – 17 43 TROUBLESHOOTING Problem No sound from the effect speakers. Cause Remedy Press EFFECT to turn it on. 29 A Dolby Surround, Dolby Digital or DTS decoding DSP program is being used with material not encoded with Dolby Surround, Dolby Digital or DTS. Select another DSP program. 57 – 60 25 Raise the level of the center speaker. 47 “1A CENTER SP” on the SET MENU is set to NONE. Select the appropriate mode for your center speaker. 40 One of the Hi-Fi DSP programs (1 to 5) has been selected. Select another DSP program. The source encoded with a Dolby Digital or DTS signal does not have a center channel signal. No sound from the rear speakers. — The output level of the rear speakers is set to minimum. Raise the output level of the rear speakers. A monaural source is being played with the program 10. Select another DSP program. “1D LFE/BASS OUT” on the SET MENU is set to MAIN when a Dolby Digital or DTS signal is being played. Select SWFR or BOTH. 42 “1D LFE/BASS OUT” on the SET MENU is set to SWFR or MAIN when a 2-channel source is being played. Select BOTH. 42 42 “1D LFE/BASS OUT” on the SET MENU is set to SWFR or BOTH and your system does not include a subwoofer. Select MAIN. The output mode for each speaker (main, center or rear) on the SET MENU does not match your speaker configuration. Select the appropriate output mode for each speaker based on the size of the speakers in your configuration. 40, 41 Incorrect cable connections. Firmly connect the audio plugs. If the problem persists, the cables may be defective. 12 – 15 No connection from the turntable to the GND terminal. Connect the grounding cord of your turntable to the GND terminal of this unit. 12, 13 The record is being played on a turntable with an MC cartridge. The turntable should be connected to the unit through an MC-head amplifier. ADDITIONAL INFORMATION The volume level is low while playing a record. ADVANCED OPERATION A “humming” sound can be heard. 57 – 60 — The source does not contain low bass signals (90 Hz and below). Poor bass reproduction. 47 BASIC OPERAIONT No sound from the subwoofer. 57 – 60 PREPARATION The output level of the center speaker is set to minimum. INTRODUCTION The sound effect is off. A 96-kHz sampling digital signal is being input to this unit. No sound from the center speaker. Refer to page 12 APPENDIX English 69 TROUBLESHOOTING Problem Cause Remedy Refer to page 12 The volume level cannot be increased, or the sound is distorted. The component connected to the REC OUT jacks of this unit is turned off. The sound effect cannot be recorded. It is not possible to record the sound effect by a recording component. A source cannot be recorded by a digital recording component connected to the DIGITAL OUTPUT jack of this unit. A source component is only connected to the analog input jacks of this unit. Connect the source component to the digital input jacks of this unit. The sound field parameters and some other settings on this unit cannot be changed. “15 MEMORY GUARD” on the SET MENU is set to ON. Select OFF. 46 — Turn on the power to the component. 38 12 – 15 This unit does not operate properly. The internal microcomputer has been frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage. Disconnect the AC power cord from the outlet and then plug it in again after about 30 seconds. “CHECK SP WIRES” appears on the front panel display. Speaker cables are short circuited. Make sure all speaker cables are connected correctly. The sound is degraded when listening with headphones connected to a tape deck or CD player that is connected to this unit. This unit is in the standby mode. Turn on the power of the unit. — There is noise interference from digital or highfrequency equipment, or the unit. The unit is too close to the digital or highfrequency equipment. Move the unit further away from such equipment. — 70 16, 17 TROUBLESHOOTING ■ Tuner The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor. Check the antenna connections. Try using a high-quality directional FM antenna. Use the manual tuning method. 30, 31 There is multipath interference. Adjust the antenna position to eliminate multipath interference. 30 The desired station cannot be tuned in with the automatic tuning method. The station is too weak. Use the manual tuning method. Use a high-quality directional FM antenna. Previously preset stations can no longer be tuned in. The unit has been disconnected for a long period. Re-store the stations. The desired station cannot be tuned in with the automatic tuning method. The signal is weak or the antenna connections are loose. Tighten the AM loop antenna connections and orient it for best reception. Use the manual tuning method. Noises result from lightning, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat, but it is difficult to eliminate all noise. 30 A TV set is being used nearby. Move this unit away from the TV. — There are buzzing and whining noises (especially in the evening). 32 30, 31 BASIC OPERAIONT There are continuous AM crackling and hissing noises. 30, 31 PREPARATION FM stereo reception is noisy. INTRODUCTION Cause There is distortion, and clear reception cannot be obtained even with a good FM FM antenna. Remedy Refer to page Problem ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 71 TROUBLESHOOTING ■ Remote control Problem The remote control does not work nor function properly. The unit or other component cannot be controlled. Remedy Refer to page Wrong distance or angle. The remote control will function within a maximum range of 6 m (20 feet) and no more than 30 degrees off-axis from the front panel. 8 Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. Reposition the unit. — The batteries are weak. Replace all batteries with new ones. 3 The component to be controlled has not been selected. Set the selector dial to the appropriate position, corresponding to the component to be controlled. 49 Cause — The remote control cannot control system components. The remote control does not “learn” new functions. The manufacturer code has not been set up properly. Enter the code again. 54 Depending on the manufacturer or the model, some components cannot be controlled with this unit’s remote control even though the code has been set up properly. Program functions from the other remote control’s function into this remote control. 55 The batteries of this remote control and/or the other remote control are too weak. Replace the batteries. 3 The distance between the two remote controls is too much or too little. Place the remote controls at the proper distance. 55 The signal coding or modulation of the other remote control is not compatible with this remote control. Learning is not possible. 55 Memory capacity is full. Further learning is not possible without deleting unnecessary functions. 55 Try setting another code for the same manufacturer. After this unit has been exposed to a strong external electric shock (such as lightning and strong static electricity) or if you mishandle the operation of this unit, it may not function properly. In these cases, set this unit in the standby mode, disconnect the power cord, plug it back in after 30 seconds, and start operating. 72 SPECIFICATIONS FM SECTION • Minimum RMS Output Power for Main, Center, Rear 20 Hz to 20 kHz, 0.04% THD, 8 ohms ............................... 100 W 1 kHz, 0.04% THD, 8 ohms ................................................ 105 W • Tuning Range .................................................. 87.50 to 108.00 MHz • DIN Standard Output Power 1 kHz, 0.7% THD, 4 ohms .................................................. 140 W • IEC Output Power 1 kHz, 0.04%, 8 ohms ......................................................... 105 W • Damping Factor 20 Hz to 20 kHz, 8 ohms .............................................. 80 or more • Selectivity (400 kHz) ............................................................... 70 dB • Signal to Noise Ratio (IHF) Mono/Stereo .............................................................. 76 dB/70 dB • Harmonic Distortion (1 kHz) Mono/Stereo ................................................................. 0.2%/0.3% • Stereo Separation (1 kHz) ....................................................... 45 dB • Frequency Response ........................... 20 Hz to 15 kHz +0.5, –2 dB • Frequency Response CD to Main L/R ...................................... 10 Hz to 100 kHz, –3 dB AM SECTION • Total Harmonic Distortion 20 Hz to 20 kHz, 50 W, 8 ohms, Main L/R .......................... 0.04% • Usable Sensitivity ............................................................. 300 µV/m • Residual Noise (IHF-A Network) Main L/R ................................................................ 150 µV or less • Channel Separation (1 kHz/10 kHz) CD (5.1 kohms terminated) to Main L/R .................. 60 dB/45 dB GENERAL • Power Supply ......................................................... AC 230 V/50 Hz • Power Consumption .................................................. approx. 300 W Standby Mode ......................................................... approx. 1.2 W • AC Outlets (Total 100 W maximum) [Europe model] ..................................................... 2 (SWITCHED) [U.K. model] ........................................................ 1 (SWITCHED) • Tone Control (Main L/R) BASS Boost/Cut ...................................................... ±10 dB/50 Hz TREBLE Boost/Cut ............................................... ±10 dB/20 kHz BASS EXTENSION ................................................. +6 dB/60 Hz • Dimension (W x H x D) ............................ 435 x 171 x 432 mm (17-1/8” x 6-3/4” x 17”) • Phones Output ..................................................... 150 mV/100 ohms • Accessories .............................................................. Remote Control ....................................................................................... Batteries ......................................................................... AM loop antenna ...................................................................... Indoor FM antenna ................ 75-ohm/300-ohm antenna adapter (U.K. model only) ................................................................. Quick Reference Card * Specifications are subject to change without notice. ADDITIONAL INFORMATION • Output Level REC OUT ........................................................ 150 mV/0.9 kohms PRE OUT ............................................................ 2.6 V/1.2 kohms SUBWOOFER .................................................... 4.0 V/1.2 kohms • Weight ......................................................................... 15 kg (33 lbs) ADVANCED OPERATION • Input Sensitivity CD, etc .............................................................. 150 mV/47 kohms PHONO ............................................................. 2.5 mV/47 kohms 6CH INPUT .............................................. 150 mV/40 – 47 kohms BASIC OPERAIONT • Signal to Noise Ratio (IHF-A Network) PHONO MM to REC OUT (5 mV, shorted) ........................ 81 dB CD (250 mV, shorted) to Main L/R, Effect Off ................. 100 dB • Tuning Range ......................................................... 531 to 1611 kHz PREPARATION • Dynamic Power (IHF) 8/6/4/2 ohms ................................................... 125/160/195/230 W • 50 dB Quieting Sensitivity (IHF, 100% mod.) Mono/Stereo ........................ 2.0 µV (17.3 dBf) /25 µV (39.2 dBf) INTRODUCTION AUDIO SECTION VIDEO SECTION • Video Signal Type ...................................................................... PAL • Composite Video Signal Level ................................ 1 Vp-p/75 ohms • S-Video Signal Level Y ........................................................................... 1 Vp-p/75 ohms C .................................................................... 0.286 Vp-p/75 ohms APPENDIX • Component Video Signal Level Y ........................................................................... 1 Vp-p/75 ohms PB/CB, PR/CR ....................................................... 0.7 Vp-p/75 ohms • Signal to Noise Ratio ............................................................... 50 dB • Frequency Response (MONITOR OUT) Composite, S-Video ................................. 5 Hz to 10 MHz, –3 dB Component ................................................. DC to 30 MHz, –3 dB English 73 LIST OF MANUFACTURER’S CODES LISTES DES CODES FABRICANT VERZEICHNIS DER HERSTELLERCODES LISTA ÖVER TILLVERKARKODER ELENCO DEI CODICI DEL FABBRICANTE LISTA DE CÓDIGOS DE FABRICANTES LIJST VAN CODES VAN FABRIKANT CLARIVOX 0821, 0961, 1971 CLATRONIC 1181, 1331 CONCERTO 0791 CONDOR 0761 CONTEC 0151, 1171 CONTINENTAL EDISON 0571, 0651, 0901 CRAIG 1171 CROSLEY 0021, 0491, 1021, 1081, 1401, 1981, 2201, 2251, 2271 CROWN 2541 CTC CLATRONIC 0261 CXC 1171 DAEWOO 0101, 1501, 1511, 2611 DANSAI 0101 DECCA 0271, 0581, 0601, 0971, 1101, 1691 DECCA (UK) 0271, 0581, 0601, 1101, 1681 DEGRAAF 0451, 1351 DIXI 0991, 1511 DOMEOS 0101 DORIC 1031 DUAL 0091, 0601, 1611, 1641, 2101 DUAL-TEC 0601, 1511, 1621, 2111 DUMONT 0261, 0521, 0781, 1021, 1081, 1981, 2121, 2151 DYNATRON 0101 ELBE 1551, 1971, 2031 ELECTRO TECH 1511 ELEKTRONSKA 0771 ELMAN 0261, 1621 ELTA 1511 EMERSON 0921, 1021, 1081, 1121, 1171, 1261, 1301 ERRES 0101 ETRON 1981 EUROPHON 0261, 0581, 0601, 0771, 1091, 1621, 2001 FENNER 0101, 1511 FERGUSON 0281, 0371, 0551, 0651, 0781, 0861, 0881, 1131, 1181, 1361, 1461, 1971, 1991, 2281, 2311, 2341 FIDELITY 0451, 0761, 2281 FIDELITY (UK) 0561, 0591, 1931, 2281 FILMNET 1141 FINLANDIA 0451, 2321 FINLUX 0021, 0261, 0491, 0521, 0781, 0811, 0871, 1081, 1411, 1421, 1981, 2051, 2091, 2121, 2151, 2551 TV ADMIRAL 0411, 0451, 0911, 1021, 1081 AIKO 0891 AKAI 0061, 0101, 0231, 1191, 1351, 1591, 1641, 1791, 1891, 1981 AKURA 1331 ALBA 1241, 1331, 2361 ALBIRAL 1971 AMSTRAD 1301, 1511 ANAM 1171 ARC EN CIEL 0571 ARCAM 0571, 0761 ARISTONA 0751 ARTHUR MARTIN 0451, 1641 ASA 0411, 0451, 0521, 0781, 0871, 1021, 1081, 1421, 2051, 2091, 2151, 2551 ASTRA 1511 ATANTIC 0761 ATLANTIC 0761 ATORI 1511 AUDIOSONIC 1181, 1321, 1511 AUSIND 0491, 1411 AUTOVOX 0091, 0351, 0481, 0491, 0601, 0781, 0951, 1051, 1081, 1391, 1421 BAIRD 1101, 1351 BANG & OLUFSEN 1081 BASIC LINE 1321, 1331 BAUER 1451 BAUR 0041, 0061, 0121, 0131, 0221, 1561 BEKO 2491, 2501 BLAUPUNKT 0221, 0231, 0241, 0251, 0471, 0741, 2201, 2211, 2221, 2231, 2241, 2261, 2571, 2581 BRANDT 0571, 0651, 0731, 0901, 1821 BRIONVEGA 1021, 1051, 1081 BRITANNIA 0761 BRUNS 0821, 0991, 1021, 1081 BSR 0391, 0691, 1621, 1901, 1981 BUSH 0451, 1241, 1331, 1641, 1741, 2131, 2151 BUSH (UK) 0481, 1561, 1611 CANDLE 0791 CENTURY 1021, 1081 CGE 0491, 0811, 0981, 1401, 1531, 1611, 1621, 1981, 2201, 2251, 2271 CITIZEN 0791 FIRST LINE FISHER 1981 0021, 0091, 0141, 0511, 0601, 0801, 0821, 0981, 1021, 1081, 1981, 2091 FORGESTONE 2281 FORMENTI 0451, 0491, 0761, 1081, 1451, 1541, 1981 FORMENTI-PHOENIX 0021, 0431, 0451, 0591, 1411 FORTRESS 1081 FRONTECH 0451, 1181, 1981 FUJITSU 1261 FUNAI 0391, 0691, 1171, 1181, 1261 FUTURETECH 1171 GBC 0021, 0141, 1321, 1511, 1621, 1981 GEC 0451, 1101, 1281, 2321 GEC (UK) 0031, 0081, 0581, 0601, 1101, 1281, 1561 GELOSO 0021, 0411, 0451, 1321, 1511, 1621, 1981 GENERAL TECHNIC 2681 GENEXXA 0451, 1331 GOLDSTAR 0591, 0601, 0761, 0791, 1371, 1491, 1511, 1561, 1621, 1641 GOODMANS 0141, 1101, 1371, 1641, 2301 GORENJE 0981, 1061 GRAETZ 0451 GRANADA 0141, 0451, 0491, 0581, 0601, 1101, 1111, 1351, 1981, 2321 GRANADA (UK) 0081, 0141, 0451, 0491, 0581, 0601, 1031, 1311, 1521, 1561, 1641 GRUNDIG 0221, 0231, 0471, 0491, 0711, 0741, 1381, 2021, 2041, 2141, 2151 HANSEATIC 0021, 0121, 0141, 0431, 0591, 1561 HANTAREX 0581 HEMMERMANN 0061 HIFIVOX 0331, 0571 HINARI 0071, 0141, 0451, 1261, 1351, 1511, 1641, 1981, 2011 HITACHI 0001, 0011, 0031, 0081, 0141, 0291, 0331, 0341, 0451, 0601, 0631, 0701, 1281, 1561, 1601, 1821, 1831, 1841, 1861, 1871, 1881, 1891, 1941, 1981, 2051, 2321, 2341 HYPER 0591, 0601, 1511, 1621 IMPERIAL 0451, 0491, 0811, 0981, 1401, 1611, 1621, 2201, 2251, 2271 INGERSOL 1511 INNO HIT 0581, 0601, 0841, 1101, 1331, 1371, 1511, 2011 INNOVATION 2591, 2601, 2611, 2621, 2641, 2651, 2661, 2711, 2721, 2761, 2771, 2781 INTERFUNK 0031, 0041, 0061, 0121, 0181, 0451, 0491, 1081, 1641, 1791, 1821, 1981, 2231 IRRADIO 0491, 1321, 1331, 1371, 1411, 1511, 2011 ISUKAI 1331 ITT 0031, 0041, 0051, 0061, 0071, 0081, 0181, 0411, 0451, 0491, 1241, 1291, 1351, 1501, 1601, 1641, 1741, 1921, 1981, 2091, 2331, 2431 ITT-NOKIA 0031, 0041, 0051, 0061, 0071, 0081, 0181, 0411, 0451, 0491, 1241, 1291, 1351, 1501, 1601, 1641, 1741, 1921, 1981, 2091, 2331, 2431 JVC 0071, 0721, 1441, 1581, 1591, 1741, 1791 KAISUI 0591, 1321, 1331 KAMOSONIC 0601 KARCHER 0591, 0601, 0841, 1091, 1321, 1511, 1561, 2051 KAWASHO 0761 KENDO 0261 KENNEDY 0021, 0351, 0951, 1981 KONKA 2701 KORTING 0431, 1011, 1021, 1081, 1541 i 08V800RDS_code(GB) 1 8/29/0, 10:00 AM NECKERMANN KTV LENOIR LEYEO LIFETEC 0601, 1171 0601, 1511 1181 2591, 2601, 2611, 2621, 2641, 2651, 2661, 2671, 2681, 2691, 2711, 2761, 2771, 2781 LOEWE OPTA 0121, 0131, 0581, 0611, 1081 LOGIC 1691, 2281 LOGIK 0551, 1681, 2281 LOWEWE 0831 LUMA 0351, 0451, 1901 LUXMAN 0791 LUXMAN STEREO TUNER 0791 LUXOR 0001, 0061, 0181, 0341, 0421, 0451, 0461, 0491, 0601, 0671, 1351, 1371, 1561, 1601, 1911, 1921, 1981 LYCO 1181 MAGNADYNE 0021, 0061, 0261, 0581, 0641, 0771, 1021, 1081, 1621, 1981 MAGNAFON 0261, 0491, 0581, 0591, 0641, 0761, 1091, 2001 MANESTH 0101 MARANTZ 0101 MARELLI 1081 MARK 0101 MATSUI 0061, 0451, 0601, 0691, 1101, 1151, 1241, 1271, 1301, 1511, 1561, 1681, 1691 MAXIMAL 0071, 1981 MCMICHAEL 1281 MEDION 2591, 2601, 2611, 2621, 2641, 2651, 2661, 2671, 2681, 2691, 2711, 2721, 2761, 2771, 2781 MEMOREX 1511 METZ 0231, 0741, 1001, 1041, 1081, 1481, 2071, 2081 MGA 1231 MICROMAXX 2591, 2621, 2641, 2651, 2711, 2761, 2771, 2781 MINERVA 0221, 0231, 0491, 1381, 2141, 2151 MISTRAL 2281 MITSUBISHI 0141, 0201, 0231, 0661, 1191, 1201, 1231, 1671, 1691, 1741 MIVAR 0491, 0501, 0581, 0591, 0761, 0771, 1371, 1431, 2031 MTC 0791 MULTITECH 0261, 0581, 0601, 0641, 0981, 1321, 1511 MURPHY 0451, 2091 MURPHY (UK) 0081, 1031 N.E.I. 0101, 0961 NAD 1341 NEC 0141, 1711, 1721, 1731 NEDIATOR NICAMAGIC NIKKAI 0451, 0601, 0981, 1081, 1561, 1931, 1981, 2211, 2231, 2241 0101 0761 1101, 1331, 1641, 1701, 2011 NOBLIKO 0261, 0491, 0591, 0641, 1381, 1411 NOGAMATIC 0571 NOKIA 0031, 0041, 0051, 0061, 0071, 0081, 0181, 0411, 0451, 0491, 1241, 1291, 1351, 1501, 1601, 1641, 1741, 1921, 1981, 2091, 2331, 2431, 2461, 2791 NORDMENDE 0031, 0291, 0331, 0451, 0531, 0541, 0571, 1051, 1131, 1591, 1791, 1811, 1821, 1891, 1941, 2631 OCEANIC 0321, 1651, 1981 OCEANIC (F) 0031, 0061, 0321, 0441, 1661 ONCEAS 0601 ONWA 1171 ORION 0061, 0391, 0691, 0851, 1211, 1241, 1251, 1301, 1481, 1511, 1681, 1691, 1981, 2371, 2421 OSAKA 2011 OSAKI 1101, 1331, 2011 OSUME 0151 OTTO VERSAND 0021, 0121, 0141, 0221, 0601, 1561, 1741, 1981 PAEL 0591, 1411 PANASONIC 0031, 0201, 0211, 0451, 0701, 1311, 1751, 1961, 2561, 2741 PANORAMIC 2351 PATHE MARCONI 0571 PATHE’ CINEMA (F) 0431, 0591, 1621, 1661, 1971 PAUSA 1511 PAUZA 1511 PERDIO 0891, 1101 PHILCO 0021, 0491, 0811, 0981, 1021, 1081, 1401, 1611, 1621, 1751, 2201, 2251, 2271, 2451, 2471 PHILIPS 0101, 0361, 0591, 0621, 0681, 0751, 0761, 1021, 1081, 1281, 2031, 2281, 2291, 2431, 2441, 2511, 2731 PHOENIX 1081 PHONOLA 0751, 1081 PIONEER 0291, 0451, 1341, 1821 PRANDONI-PRINCE 0411, 0451, 0491, 0581, 1411 PRANDONI-PROMCE 0451, 0491, 0581 PRIMA PROFEX PROTECH QUELLE 0451 1981 0641, 1181, 1981 0041, 0061, 0121, 0221, 0231, 0391, 0491, 0521, 0601, 0781, 1371, 1381, 1411, 1421, 1641, 1681, 2051, 2091, 2141, 2151, 2201, 2211, 2231, 2241, 2251, 2271, 2551, 2571, 2581 REDIOMARELLI 0101, 0451, 0661, 0771, 1081 RADIONETTE 0031, 2051, 2091 RADIOLA 2291 RANK 0481, 2151 RBM 2131, 2151 RBM (UK) 0481 REDIFFUSION 0451, 0661, 1641, 1981, 2331 REDIFFUSION (UK) 0061, 0081, 1031 REX 0071, 0101, 0351, 0411, 0451, 0951, 1901, 2061, 2101, 2111 RFT 0991, 2511 ROADSTAR 1321, 1511 ROTEL 0151 SABA 0291, 0331, 0421, 0451, 0531, 0541, 0571, 0581, 0651, 0731, 0931, 1021, 1071, 1081, 1131, 1791, 1811, 1821, 1891, 1941, 2631 SACCS 1971 SAISHO 0451, 0601, 1161, 1241, 1301, 1511, 1671, 1681, 1691 SALORA 0011, 0041, 0061, 0071, 0341, 0451, 0671, 1291, 1351, 1521, 1561, 1601, 1641, 1911, 1921, 1931, 1981, 2321 SAMBERS 0261, 0491, 0581, 0641, 1091, 1371, 1411, 2001 SAMSUNG 0101, 0601, 0841, 0981, 1101, 1181, 1371, 1511, 2011 SANYO 0141, 0151, 0401, 0601, 0801, 0821, 0981, 1021, 1101, 1111, 1291, 1351, 1691, 1741, 2051, 2091, 2551 SBR 0681, 0751, 1281, 2281 SCHAUB LORENZ 0451 SCHNEIDER 0021, 0071, 0091, 0451, 0511, 0591, 0601, 0751, 1321, 1361, 1621, 1641, 2101, 2111, 2291 SCOTT 1171, 1261 SEG 0261, 0601, 0821, 0991 SEI 0641, 0691, 1081, 1301, 1481, 1981 ii 08V800RDS_code(GB) 2 8/29/0, 10:00 AM SELECO 0071, 0101, 0351, 0411, 0451, 0951, 1901, 2061, 2101, 2111 SENTRA 1601 SHARP 0141, 0151, 0191, 1761, 1781 SIAREM 0021, 0261, 0581, 0641, 1021, 1081, 1981 SICATEL 1971 SIEMENS 0151, 0221, 0231, 0451, 0741, 2011, 2201, 2211, 2221, 2231, 2241, 2261, 2571, 2581 SILVER 1181 SINGER 0021, 0261, 1021, 1081 SINUDYNE 0021, 0061, 0101, 0261, 0391, 0641, 0691, 0851, 0941, 1021, 1081, 1241, 1301, 1321, 1481, 1631, 1981 SKANTIC 0451 SOLAVOX 0451, 1641, 2011 SONOKO 0101, 1181, 1511 SONY 0141, 0171, 1121, 1681, 1691, 2751 SOUNDESIGN 1171 SSS 1171 STERN 0071, 0101, 0351, 0411, 0451, 0951, 1901, 2061, 2101, 2111 SUNKAI 0691 SUPRA 0791 TANDBERG 0161, 0331, 0611, 1021, 1421, 1771, 1791, 2081 TANDY 0191, 0451, 1331, 1531 TASHIKO 0141 TATUNG 0271, 0581, 0601, 0971, 1101, 1681, 1691 TCM 2621, 2641, 2711, 2761, 2771, 2781 TECHNICS 1311 TECHWOOD 0791 TEKNIKA 1171, 1231, 1261 TELE 1141 TELEAVIA 0571, 0651, 0731, 1821 TELEFUNKEN 0291, 0301, 0311, 0551, 0731, 1131, 1471, 1591, 1791, 1801, 1811, 1821, 1991, 2161, 2171, 2181, 2191, 2201, 2251, 2271, 2521, 2631 TELETECH 1511 TEMPEST 2381, 2391, 2401, 2411 TENSAI 1331, 2091 TEXET 0601 THOMSON 0331, 0481, 0531, 0571, 0631, 0651, 0731, 0901, 1241, 1571, 1591, 1791, 1811, 1821, 1891, 1941, 2531 THORN 0741, 0861, 2091, 2251, 2271, 2281 THORN-FERGUSON 0281, 0371, 0551, 0651, 0781, 0861, 0881, 1131, 1181, 1361, 1461, 1971, 1991, 2281 TMK 0141, 0791, 1471 TOSHIBA 0141, 0381, 0481, 1221, 1271, 1701, 1741, 1851, 2151, 2801, 2811 TRANS CONTINENS 0451 TRISTAR 2281 TRIUMPH 0481, 0581, 2121 UHER 0431, 0451, 0481, 0491, 0511, 1311, 1541 ULTRAVOX 0021, 0261, 0591, 1021, 1081, 1981 UNIVERSUM 1181, 2051 UNIVOX 1971 VEGAVOX 0811 VEXA 0101, 1511 VICTOR 1441, 1591 VIDEOTON 2481 VORTEC 0101, 0651 VOXSON 0411, 0451, 0491, 1021, 1081 WALTHAM 0451 WATSON 0431, 2201, 2241 WATT RADIO 0021, 0061, 0261, 0591, 0641, 0761, 1091, 1971, 1981, 2001 WEGA 0141, 1081, 1981 WEGA COLOR 1021 WELTBLICK 0101 WESTON 1621 WHITE WESTINGHOUSE 0101, 0261, 0431, 0591, 0761, 1401, 1541 YOKO 0601, 1511 ZANUSSI 0071, 0101, 0351, 0411, 0451, 0951, 1901, 2061, 2101, 2111 ZOPPAS 0451 SATELLITE TUNER AKAI ALBA AMSTRAD 1276 0826, 1276 0166, 0796, 1016, 1026, 1296 ANKARO 0476 AST 0406 ASTRA 0126 BARCOM 0476 BLAUPUNKT 0966 BMC SATELLITE 0106 BRITISH TELECOM 1276 BUSH 0826 BUSH (UK) 0956 CAMBRIDGE 0196, 1276 CANAL PLUS (FRANCE) 1536 CHAPARRAL 0016, 0696, 1006 COLUMBUS 0616 CONNEXIONS 0306, 0426 DISCUS ELIPSE 0856, 0866 DISKXPRESS 0426, 0476 DRAKE 1516 ECHOSTAR 0226, 0236, 0606, 0626, 0666, 0926, 0996, 1046, 1056, 1066, 1106 ELTA 1286 ELTA SAT 0146 EURODEC 1226, 1236, 1246 FERGUSON 0046, 0176, 0186, 0296, 0846, 0956, 1306 FINLUX 0976 FRACARRO 0026, 0536, 0776 FUBA 0476, 0616, 0636, 1056 GIUCAR RECORD 0206, 0336 GRUNDIG 0176, 0946, 0956, 0966 HIGH PERFORMANCE 0916 HIRSCHMANN 0756, 0966 HITACHI 0446, 0516, 0706, 0946 ICX INTERNATIONAL 0886 ITT 0066, 0126, 0176, 0446, 1156 ITT/NOKIA 0066, 0126, 0176, 0446, 1156 JEEMON 0146 JERROLD 0846, 0986 JOHANSSON 0246 JVC 1276 KATHREIN 0116, 0266, 0276, 0366 KOSMOS 0266 KYOSTAR 1036, 1086 LENG 0246 LIFESAT 1326, 1346, 1356 LUXOR 0126, 0136, 0446, 0466, 0506, 1156 MACAB 0356 MASPRO 0016, 0116, 0256, 0956 MEDION 1326, 1346 METZ 0966 MICROMAXX 1326, 1346 MITSUBISHI 0966 MORGANS 0596 MURATTO 0406 NEC 0286, 0316, 0766, 0786, 0836 NETWORK 0046 NIKKO 1136, 1146 CABLE TV CABLETIME 1446, 1456, 1476 CLYDE CABLEVISION 1426 FILMNET 1396, 1436 FRANCE TELECOM 1386 GEC 1426 JERROLD 1416 MOVIE TIME 1466 NSC 1466 PHILIPS 1386 PIONEER 0006 SAMSUNG 1496 SCIENTIFIC ATLANTA 1486, 1506 STARCOM 1416 STS 1466 TANDBERG 1366 TELE 1436 TELE +1 1436 TELESERVICE 1406, 1476 TUDI 1376 UNITED CABLE 1416 ZENITH 1406 NOKIA 0066, 0126, 0176, 0446, 1156, 1166, 1336 NORSAT 0786 OTTO VERSAND 0966 PACE 0046, 0176, 0296, 0936, 0956, 1306, 1566, 1576 PACE MSS 0946 PACE SKY DIGITAL BOX (UK) 1526 PALCOM 0616, 0686, 0706 PALSAT 0396 PALTEC 0706 PANASONIC 0806, 1306 PANSAT 1076 PHILIPS 0326, 0346, 0476, 0956, 1126, 1186, 1196, 1206, 1216, 1306, 1316 PROSAT 1176 PTT TELECOM 0306, 0896 QUELLE 0966 RADIX 1056 REDIFFUSION 0316, 0786 RFT 1186, 1196, 1206, 1216 SAGEM 1256, 1546 SAKURA 0566, 0816 SALORA 0066, 0126, 0136, 0446, 0456, 0486, 0496, 0576 SAMSUNG 0746, 0756 SAT 0406 SATCOM 0896 SATECO 0646 SECTOR 1266 SEDEA 1096 SENTRA 0416 SIEMENS 0896, 0966 SINTRACK 0906 SKYLAB 0476 SKYSCAN 0876 SONY 0736, 0946 STELLA 0306 STRONG 0156, 0396, 1036, 1086 STV 0636 TANDBERG 1116 TANDY 0916 TANTEC 0616 TATUNG 0516, 0546 TECHNISAT 0086, 0096, 0526, 0556, 1056 TELECOM 0306 TELEMAX 0586 THORN-FERGUSON 0046, 0076, 0176, 0186, 0956 TOSHIBA 0946 TPS (FRANCE) 1546 TRIAD 0406 UNIDEN 0036, 0216, 0676, 0716, 0726 US ELECTRONICS 0886 VORTEC 0756, 1036, 1076 VTECH 0436 WINERSAT 0246 WISI 0056, 0356, 0376, 0386, 0406, 0656, 1056, 1156 WOLSEY 0916 XCOM MULTIMEDIA 1556 XSAT (FRANCE) 1556 ZEHNDER 0266, 0406 ZENDER 0406 VCR AIWA AKAI 0042, 0352, 0432 0042, 0422, 0492, 0582, 0612, 0642, 0652, 0762, 0912 ALBA 0002, 0112, 0282, 0332, 0342, 0972 AMSTRAD 0322, 0432, 0452 ANITECH 0002 ANITSCH 1002 ASA 0012, 0052 AUDIOSONIC 0002 BAIRD 0042, 0282, 0492 BANG & OLUFSEN 0042 BAUR 0052, 0062, 0812 BLAUPUNKT 0062, 0092, 0252, 0462, 0672, 0992 BRIONVEGA 0032 BUSH 0002, 0282, 0332, 0342, 0512, 0972 BUSH (UK) 0812 CAPEHART 0112 CGE 0042, 0432, 0762 CRAIG 0072, 0482 CROWN 0112, 0282, 0622 DAEWOO 0112, 0282, 0622 DANSAI 0012 DAYTRON 0112 DECCA 0042, 0052, 0432, 0942 DECCA (UK) 0052 DEGRAAF 0052, 0132, 0432, 0532, 0602 DIXI 0442 DUAL 0042, 0632 DUMONT 0052, 0432, 0532 DYNATECH 0432 DYNATRON 0012 ELBE 0122 ELIN 0072 EMERSON 0012, 0162, 0202, 0432, 0512, 0522 ERRES 0012 FERGUSON 0042, 0712, 0722, 0852, 0902, 1012, 1022, 1082 FIDELITY 0432 FINLANDIA 0052, 0532 FINLUX 0012, 0042, 0052, 0082, 0262, 0382, 0432, 0462, 0492, 0532, 0572, 0602, 0912 FIRST LINE 0002, 0912 FISHER 0162, 0482, 0532, 0542, 0572, 0592 FORMENTI-PHOENIX 0012, 0052 FRONTECH 0112 FUNAI 0432 GBC 0002 GEC (UK) 0022, 0052 GELOSO 0002 GENERAL TECHNIC 1172 GOLDSTAR 0012, 0122, 0812, 0952 GOODMANS 0002, 0072, 0282, 0432, 0502 GOODMANS (UK) 0002 GRAETZ 0022, 0042 GRANADA 0052, 0132, 0532, 0572 iii 08V800RDS_code(GB) 3 8/29/0, 10:00 AM NOKIA 0022, 0032, 0042, 0072, 0292, 0492, 0532, 0572, 0762, 1152 NORDMENDE 0042, 0102, 0142, 0192, 0222, 0242, 0392, 0402, 0632, 0732, 0742, 0762, 0782, 0792, 0832, 0842, 0872 OLYMPUS 0462 OPTONICA 0132, 0502 ORION 0162, 0202, 0312, 0442, 0512, 0522, 0982 OSAKA 0432 OSAKI 0002, 0012, 0432 OTTO VERSAND 0052, 0062, 0812 PANASONIC 0022, 0212, 0462, 0672, 0992, 1092, 1102, 1182 PENTAX 0172, 0602 PERDIO 0432 PHILCO 1062 PHILIPS 0052, 0082, 0092, 0152, 0182, 0362, 0372, 0382, 0472, 0502, 1072 PHONOLA 0052, 0152 PILOT 0012 PIONEER 0052, 0142, 0372, 0472 PORTLAND 0112 PROLINE 0432 PYE 0052, 0152 QUARTZ 0572 QUELLE 0012, 0032, 0042, 0052, 0062, 0072, 0092, 0202, 0462, 0522, 0942 RADIONETTE 0022 REALISTIC 0012, 0072, 0132, 0432, 0482, 0502, 0532, 0572 RET 1072 REX 0042, 0742, 0782 RICOH 0952 SABA 0042, 0142, 0192, 0222, 0242, 0392, 0632, 0732, 0742, 0762, 0772, 0782, 0792, 0872 SAISHO 0162, 0202, 0292, 0442, 0512, 0522, 0972 SALORA 0192, 0572, 0812, 0822, 0912 SAMSUNG 0052, 0072, 0622, 0652, 1192 SANSUI 0042, 0142 SANYO 0482, 0532, 0562, 0572 SBR 0052, 0152, 0182 SCHAUB LORENZ 0022, 0042 SCHNEIDER 0002, 0012, 0052, 0072, 0432 SEG 0002, 0072 SEI-SINUDYNE 0442 SELECO 0042 SENTRA 0112 SHARP 0132, 0502, 0702 SHINTOM 0002 SIEMENS 0062, 0092, 0252, 0572 GRANADA (UK) 0052, 0092, 0462, 0602, 0812, 0822 GRUNDIG 0052, 0062, 0092, 0232, 0252, 0262, 0752, 0802 HANSEATIC 0052, 0812 HARMAN/KARDON 0122, 0922 HCM 0002 HINARI 0002, 0202, 0412, 0442, 0522 HITACHI 0042, 0172, 0292, 0432, 0602, 0662, 0812, 1022 IMPERIAL 0072, 0432 INGERSOL 0442 INNO HIT 0002, 0052, 0072 INNOVATION 1142, 1162, 1172 INTERFUNK 0022, 0052 IRRADIO 0002, 0012 ITT 0022, 0032, 0042, 0072, 0292, 0492, 0532, 0572, 0762 ITT-NOKIA 0022, 0032, 0042, 0072, 0292, 0492, 0532, 0572, 0762 JENSEN 0042 JVC 0042, 0102, 0142, 0272, 0742, 0762, 0782, 0902 KARCHER 0052, 0072, 0812 KENDO 0492 KENWOOD 0042, 0142, 0572 LIFETEC 1142, 1162, 1172 LLOYD 0432 LOEWE OPTA 0052, 0092, 0152 LOGIK 0002, 0072, 0442 LUMA 0162 LUXOR 0492, 0572, 0812 M ELECTRONIC 0432 MAGNADYNE 0052 MAGNASONIC 0572 MANESTH 0012 MARANTZ 0012, 0052, 0092, 0122, 0502 MARK 0012 MARTA 0012 MATSUI 0012, 0442, 0512, 0522, 0812, 0972 MEDION 1142, 1162, 1172 MEMOREX 0012, 0132, 0432, 0482, 0532, 0572 METZ 0062, 0092, 0932 MGA 0912 MICROMAXX 1142, 1162, 1172 MINERVA 0062, 0092, 0252 MINOLTA 0172, 0602 MITSUBISHI 0052, 0062, 0142, 0912, 0922 MTC 0072, 0432 MULTITECH 0002, 0052, 0062, 0282, 0432 MURPHY 0432 N.E.I. 0012, 0052 NATIONAL 0462 NEC 0042, 0122, 0142 NECKERMANN 0032, 0042, 0052, 0072, 0092, 0202, 0522, 0572, 0762, 0812 NIKKAI 0112 NOBLIKO 0092 SINUDYNE 0052, 0382, 0442, 0932 SONOKO 0282 SONY 0432, 0552, 0682, 0692, 0942, 0952, 0962, 1122, 1132 STS 0602 SUNKAI 0512 SUNSTAR 0432 SYLVANIA 0432, 0912 SYMPHONIC 0432, 0912 TANDBERG 0062, 0162, 0522, 0932 TASHIKO 0132, 0432 TATUNG 0042, 0052, 0432, 0922 TCM 1142, 1162, 1172 TEAC 0042, 0432 TECHNICS 0462 TEKNIKA 0012, 0432 TELEFUNKEN 0042, 0192, 0632, 0732, 0742, 0762, 0782, 0882, 0892 TEMPEST 1032, 1042, 1052 TENOSAL 0002 THOMSON 0042, 0102, 0142, 0192, 0402, 0632, 0762 THORN 0042, 0902 THORN-FERGUSON 0042, 0222, 0302, 0712, 0722, 0742, 0762, 0852, 0862, 0872, 0902 TMK 0522 TONSAI 0002 TOSHIBA 0042, 0622, 0912 TOTEVISION 0012, 0072 TRIUMPH 0922 UHER 0042, 0072 ULTRAVOX 0032 UNITECH 0072 VECTOR RESEARCH 0122 VICTOR 0042, 0102, 0142 VIDEON 1162, 1172 WELTBLICK 0012 WHITE WESTINGHOUSE 0032 XENON 0162 YAMAHA 0042, 1202 YOKO 0012, 0062, 0072 DVD PLAYER AKAI JVC KENWOOD MAGNAVOX MITSUBISHI ONKYO PANASONIC PHILIPS PIONEER PROSCAN RCA SAMSUNG SHARP SONY TECHNICS THOMSON TOSHIBA YAMAHA ZENITH 0108 0168, 0348 0288 0248 0268 0128, 0248 0048 0188, 0248 0208, 0228 0308 0308 0148 0068 0028 0048 0328 0088, 0248 0008, 0048 0248 iv 08V800RDS_code(GB) 4 8/29/0, 10:00 AM LD PLAYER AIWA FUNAI HITACHI MAGNAVOX PANASONIC PIONEER RCA REALISTIC SAMSUNG SONY VICTOR YAMAHA 0137 0137 0047 0077 0027 0037 0067 0137 0017, 0087 0057, 0097, 0107, 0117 0127 0007 CD PLAYER ACCUPHASE ADC ADCOM AKAI 0315 0865 0785, 1015 0115, 0125, 0725, 0735, 0745, 0935, 1155 ARCAM 1875 ARCAM-ROTEL 0165 AUDIO-TECHNICA 0835 AUDIOSONIC 0155 AIWA 1105, 1235, 1245, 1765, 1915, 1935 BSR 0875 CALIFORNIA AUDIO LAB 1075 CARRERA 0555, 0875 CARVER 0825, 1415 CYRUS-ROTEL 0205 DENON 0045, 0955, 1045, 1595, 1795, 1805 DUAL 1005 ELIN 0185 EMERSON 1015, 1285, 1675 FISHER 0105, 0595, 0605, 0825, 1165, 1175 GENEXXA 0525, 0825, 0855, 0875, 0995, 1265, 1285, 1345, 1355, 1485, 1575, 1675, 1715, 1825 GOLDSTAR 0555, 1185, 1195, 1585 GRUNDIG 0175 HARMAN KARDON 0325, 0495, 0565, 1135, 1145, 1155 HITACHI 0065, 0585, 0685, 0945, 1005, 1015, 1225, 1545 INNOVATION 1995, 2005, 2015 ITT-NOKIA 0185 JVC 0385, 0395, 0455, 0575, 0585 KARCHER 0485 KENWOOD 0025, 0055, 0145, 0215, 0595, 0675, 0695, 0705, 0715, 0925, 1355, 1485, 1575, 1675, 1715, 1825 KORTING 0175 LIFETEC 2015 LIGHT CONTROL 1155, 1645, 1655, 1665 LINN 0165, 1875 LUXMAN 0265, 0275, 0795, 0805, 1295, 1305, 1555, 1925 THOMSON 1005 TOSHIBA 0755, 0765 VECTOR RESEARCH 0555, 0865 VICTOR 0575 YAMAHA 0005, 0015, 1815, 0085, 0345, 0615, 0655, 0815, 0835, 0895 LUXOR MAGNAVOX MARANTZ 0185, 1895, 1905 1865, 1875 0165, 0175, 0545, 0665, 1275, 1335, 1405, 1505, 1875, 1955 MATSUSHITA 1095, 1605 MCS 0535 MEDION 0075, 1995, 2005, 2015 MEMOREX 0525, 1015, 1265, 1275, 1285, 1675 MGA 1125 MICROMAXX 2015 MISSION 0165, 1875 MITSUBISHI 1125, 1205 NAD 0135, 0255, 0285, 0295, 0305, 0345, 0755, 0765, 1315, 1325 NAKAMICHI 0635, 0645, 1565 NEC 0405, 0535, 0775, 0785 NECKERMAN 0155, 0225 NIKKO 0835, 1165 OCEANIC 0185 OKANO 0155, 0225 ONKYO 0885, 1385, 1425, 1455, 1515 PANASONIC 1055, 1075, 1615, 1625 PHILIPS 0165, 0175, 0195, 1865, 1875 PIONEER 0095, 0335, 0425, 0435, 0445, 0525, 0855, 1035, 1945 PROTON 0905, 1875 QUASAR 1075 RADIOLA 1845, 1855 RADIOTONE 0485 REALISTIC 0825, 1015, 1265, 1275, 1285, 1575 ROTEL 1875 SABA 1005 SAE 1875 SALORA 0185 SANSUI 0415, 0965, 0975, 0985, 1255, 1675, 1875 SANYO 0625, 0825, 0845, 0915 SCHNEIDER 1845, 1855 SCOTT 1285, 1675 SHARP 0025, 0035, 1025, 1115, 1275, 1635, 1785, 1815, 1825, 1835 SHERWOOD 1275, 1445 SIEMENS 1085 SIGNATURE 1155 SONY 0345, 0355, 0365, 0375, 0865, 1685, 1695, 1705, 1715, 1725, 1735, 1745 SYLVANIA 1875 TANDBERG 1885 TASHIKO 1525 TCM 1985, 2015 TEAC 0235, 0245, 1275, 1365, 1375, 1395, 1435, 1465, 1475 TECHNICS 0465, 0475, 1065, 1075, 1625 TELEFUNKEN 1005 THETA DIGITAL 1865 CD RECORDER YAMAHA 0244 MD RECORDER YAMAHA KENWOOD SONY 0024, 0224, 0234 0214 0224 TAPE DECK AKAI DENON GRUNDIG HARMAN JVC KENWOOD KORTING LUXMAN MARANTZ NAD ONKYO PHILIPS PIONEER SONY YAMAHA 0124 0204 0134 0044 0194 0164 0134 0054, 0064, 0074, 0084 0134, 0144 0174 0184 0134, 0144, 0154 0034, 0114 0094, 0104 0004, 0014 v 08V800RDS_code(GB) 5 8/29/0, 10:00 AM GB RX-V800RDS YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA 0100V800RDS(GB)-cv1/4 1 RX-V800RDS Natural Sound AV Receiver Ampli-tuner audio-vidéo OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING Printed in Malaysia ID V624940-2 10/3/0, 9:14 AM Quick Reference Card AMP/TUN DSP DSP/TUN INPUT DSP INPUT Input selector buttons DSP program group buttons EFFECT PRESET –/+ 6.1/ES A/B/C/D/E TEST j/i A/B/C/D/E u/d SET MENU ON SCREEN LEVEL STANDBY TV POWER POWER VOLUME +/– TV VOLUME DSP program TV INPUT group SLEEP MUTE buttons Input selector buttons EFFECT 6.1/ES TAPE/MD (CD-R) INPUT DSP DIR A (tape) b Skip – (MD/CD-R) w Rewind (tape) Search (MD/CD-R) A/B/C/D/E DSP INPUT Numeric buttons (MD/CD-R) INDEX (CD-R) +10 (MD/CD-R) Numeric buttons Deck A/B (tape) DISPLAY (MD/CD-R) INDEX +10 e Pause (MD/CD-R) r Rec/Pause (tape/MD) p Play CD a DIR B (tape) Skip + (MD/CD-R) s Stop f Fast forward (tape) Search (MD/CD-R) AV POWER DISC SKIP –/+ p Play A/B/C/D/E DISPLAY e Pause b Skip – a Skip + s Stop w Search f Search AV POWER V624990-1 Quick Reference Card DVD/LD DVD MENU INPUT DSP INPUT DSP Numeric buttons Numeric buttons INDEX/Time (DVD) Chapter/Time (LD) +10 INDEX +10 DISC SKIP –/+ (DVD) DISC SKIP –/+ p Play A/B/C/D/E b Skip – (DVD) Skip/Chapter – (LD) w Search DISPLAY e Pause a Skip + (DVD) Skip/Chapter + (LD) s Stop f Search Return Menu select A/B/C/D/E Menu right Menu left Menu down MENU TITLE AV POWER AV POWER TV VCR INPUT DSP CBL/SAT INPUT DSP Numeric buttons Ch enter/ Recall CH –/+ A/B/C/D/E DISPLAY e Pause DSP INPUT Numeric buttons Ch enter/ Recall CH –/+ Numeric buttons CH –/+ _/_ _ _/_ _ *1 VCR REC p Play DISPLAY Menu up *1 VCR REC VCR play A/B/C/D/E DISPLAY VCR pause Menu select A/B/C/D/E Menu left s Stop w Rewind VCR stop VCR fast forward f Fast VCR rewind forward AV POWER TV POWER TV INPUT TV VOL +/– TV SLEEP Recall VCR power Ch enter _/_ _ DISPLAY/ Guide (SAT) Menu up Menu right Menu down MENU AV POWER TV MUTE *1 Press this button twice to start recording. Appuyer deux fois sur cette touche pour commencer l’enregistrement. Drücken Sie diese Taste zweimal, um die Aufnahme zu starten. Tryck två gånger på den här knappen för att börja spela in. Premere due volte questo tasto per iniziare la registrazione. Presione dos veces este botón para empezar a grabar. Druk tweemaal op deze toets om met opnemen te beginnen. V624990-1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83

Yamaha RX-V800RDS Handleiding

Categorie
Ontvanger
Type
Handleiding

Andere documenten