Yamaha YDP-113 de handleiding

Merk: Yamaha

Model: YDP-113

Categorie: Digitale piano's

Type: de handleiding

YDPYDP-113-113

Digital pianoDigital piano

Owner's Manual

Bedienungsanleitung

Mode d'emploi

Manual de instrucciones

Before using the YDP-113, be sure to read “Precautions„ on pages 6 -7.

Achten Sie darauf, vor Einsatz des YDP-113 die “Vorsichtsmassnahmen„

auf Seite 6-7 durchzulesen.

Avant d'utiliser le YDP-113, lire attentivement la section «Precautions

d'usage» aux pages 6- 7.

Antes de utilizar el YDP-113, lea las “Precauciones„ que debe tener en

cuenta en las páginas 6 - 7.

IMPORTANT

Check your power supply

Make sure that your local AC mains voltage matches the voltage specified

on the name plate on the bottom panel. In some areas a voltage selector

may be provided on the bottom panel of the main keyboard unit near the

power cord. Make sure that the voltage selector is set for the voltage in

your area. The voltage selector is set at 240V when the unit is initially

shipped. To change the setting use a "minus" screwdriver to rotate the

selector dial so that the correct voltage appears next to the pointer on the

panel.

WICHTIG

Überprüfung der Stromversorgung

Vergewissern Sie sich vor dem Anschließen an das Stromnetz, daß die

örtliche Netzspannung den Betriebsspannungswerten auf dem Typenschild

an der Unterseite des Instruments entspricht. In bestimmten

Verkaufsgebieten ist das Instrument mit einem Spannungswähler an der

Unterseite neben der Netzkabeldurchführung ausgestattet. Falls vorhanden,

muß der Spannungswähler auf die örtliche Netzspannung eingestellt

werden. Der Spannungswähler wurde werkseitig auf 240 V voreingestellt.

Zum Verstellen drehen Sie den Spannungsregler mit einem

Schlitzschraubendreher, bis der Zeiger auf den korrekten Spannungswert

weist.

IMPORTANT

Contrôler la source d'alimentation

Vérifiez que la tension spécifiée sur le panneau inférieur correspond à la

tension du secteur. Dans certaines régions, l'instrument peut être équipé

d'un sélecteur de tension situé sur le panneau inférieur du clavier à

proximité du cordon d'alimentation.

Vérifiez que ce sélecteur est bien réglé en fonction de la tension secteur de

votre région. Le sélecteur de tension est réglé sur 240 V au départ d'usine.

Pour modifier ce réglage, utilisez un tournevis à lame plate pour tourner le

sélecteur afin de mettre l'indication correspondant à la tension de votre

région vis à vis du repère triangulaire situé sur le panneau.

IMPORTANTE

Verifique la alimentación de corriente

Asegúrese de que tensión de alimentación de CA de su área corresponde

con la tensión especificada en la placa de características del panel inferior.

En algunas zonas puede haberse incorporado un selector de tensión en el

panel inferior de la unidad del teclado principal, cerca del cable de

alimentación. Asegúrese de que el selector de tensión esté ajustado a la

tensión de su área. El selector de tensión se ajusta a 240V cuando la unidad

sale de fábrica. Para cambiar el ajuste, emplee un destornillador de cabeza

"recta" para girar el selector de modo que aparezca la tensión correcta al

lado del indicador del panel.

Yamaha Manual Library

http://www2.yamaha.co.jp/manual/english/

M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

V974810 301APAP5.3-02B0 Printed in Singapore

DIC 2506

YDP-113

Digital piano

Introduction

92-469

(bottom)

SPECIAL MESSAGE SECTION

PRODUCT SAFETY MARKINGS:

Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these

graphics appears on this page. Please observe all cautions

indicated on this page and those indicated in the safety

instruction section.

See bottom of Keyboard enclosure for graphic symbol markings.

The exclamation point within the

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servic-

ing) instructions in the literature

accompanying the product.

The lightning ﬂash with arrowhead

symbol, within the equilateral trian-

gle, is intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product’s enclo-

sure that may be of sufﬁcient magni-

tude to constitute a risk of electrical

shock.

IMPORTANT NOTICE:

All Yamaha electronic products

are tested and approved by an independent safety testing

laboratory in order that you may be sure that when it is

properly installed and used in its normal and customary

manner, all foreseeable risks have been eliminated. DO

NOT modify this unit or commission others to do so

unless speciﬁcally authorized by Yamaha. Product perfor-

mance and/or safety standards may be diminished.

Claims ﬁled under the expressed warranty may be denied

if the unit is/has been modiﬁed. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE:

The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the speciﬁcations

without notice or obligation to update existing units.

ENVIRONMENTAL ISSUES:

Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is

approximately ﬁve years. When replacement becomes

necessary, contact a qualiﬁed service representative to

perform the replacement.

Warning:

Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice:

Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE:

Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the man-

ufacturer’s warranty, and are therefore the owners respon-

sibility. Please study this manual carefully and consult

your dealer before requesting service.

NAME PLATE LOCATION:

The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Model

Serial No.

Purchase Date

YDP-113

About this Owner’s Manual

ENGLISH

Thank you for purchasing the Yamaha YDP-113 Digital Piano! We recommend that you read this manual carefully so that

you can fully take advantage of the advanced and convenient functions of the YDP-113.

We also recommend that you keep this manual in a safe and handy place for future reference.

About this Owner’s Manual

This manual consists of three main sections: “Introduction,” “Reference” and “Appendix.”

Introduction (page 2):

Please read this section ﬁrst.

Reference (page 13):

This section explains how to make detailed settings for the YDP-113’s various functions.

Appendix (page 33):

This section introduces reference material.

*The illustrations of the controls in this owner’s manual are for instructional purposes only and actual appearance of

the controls may be somewhat different on your instrument.

Trademarks:

•Apple and Macintosh are trademarks of Apple Computer, Inc.

•Windows is a registered trademark of Microsoft® Corporation.

•All other trademarks are the property of their respective holders.

This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with

respect to which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all

computer software, MIDI ﬁles and WAVE data. Any unauthorized use of such programs and contents outside of per-

sonal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE,

DISTRIBUTE OR USE ILLEGAL COPIES.

YDP-113

Table of Contents

ENGLISH

Ta b le of Contents

Introduction

SPECIAL MESSAGE SECTION ...................... 2

About this Owner’s Manual........................ 3

Application Index........................................ 5

PRECAUTIONS............................................. 6

Accessories .................................................. 8

Maintenance ............................................... 8

Features....................................................... 9

Before Using the YDP-113 ........................ 10

Key Cover ...........................................................10

Music Rest ..........................................................10

Turning the Power On.......................................11

Setting the Volume.............................................11

Using Headphones.............................................12

Reference

Part Names................................................ 14

Listening to the Demo Songs ................... 15

Listening to 50 Piano Preset Songs .......... 16

Selecting & Playing Voices........................ 17

Selecting Voices..................................................17

Using the Damper Pedal....................................17

Adding Variations to the Sound – Reverb........18

Combining Two Voices (Dual mode)...............19

Transposition .....................................................20

Fine-tuning the Pitch .........................................20

Using the Metronome........................................21

About MIDI ............................................... 23

Connecting a Personal Computer ............ 24

MIDI Functions.......................................... 26

MIDI Transmit/Receive Channel Selection......26

Local Control ON/OFF......................................26

Program Change ON/OFF.................................27

Control Change ON/OFF ..................................27

Troubleshooting ....................................... 28

Options...................................................... 28

Keyboard Stand Assembly ........................ 29

Index ......................................................... 31

Appendix

MIDI Data Format / MIDI-Datenformat /

Format des données MIDI /

Formato de datos MIDI .......................... 34

MIDI Implementation Chart ..................... 38

Specifications / Technische Daten /

Caractéristiques techniques /

Especificaciones ...................................... 39

YDP113(E).book Page 4 Wednesday, April 30, 2003 10:23 AM

YDP-113

Application Index

ENGLISH

Application Index

Use this index to ﬁnd reference pages that may be helpful for your particular application and situation.

Listening

Listening to demo songs with different voices...................................................... “Listening to the Demo Songs” on page 15

Listening to songs from “50 Greats for the Piano” ...................................... “Listening to 50 Piano Preset Songs” on page 16

Playing

Using the damper pedal .................................................................................................“Using the Damper Pedal” on page 17

Playing an accompaniment that matches pitch............................................................................. “Transposition” on page 20

Fine-tuning the pitch of the entire instrument when you play the YDP-113

along with other instruments or CD music.......................................................................“Fine-tuning the Pitch” on page 20

Changing voices

Viewing the list of voices............................................................................................................. “Selecting Voices” on page 17

Simulating a concert hall ....................................................................“Adding Variations to the Sound – Reverb” on page 18

Combining two voices............................................................................... “Combining Two Voices (Dual mode)” on page 19

Practicing

Practicing with an accurate and steady tempo .................................................................“Using the Metronome” on page 21

Connecting the YDP-113 to other devices

What is MIDI? ....................................................................................................................................“About MIDI” on page 23

Connecting the computer...............................................................................“Connecting a Personal Computer” on page 24

Assembling

Assembling and disassembling the YDP-113......................................................“Keyboard Stand Assembly” on pages 29–30

YDP-113

PRECAUTIONS

ENGLISH

(1)B-7

1/2

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even

death from electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions

include, but are not limited to, the following:

●

Only use the voltage speciﬁed as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

●

Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it.

●

Use only the supplied power cord/plug.

●

Do not place the power cord near heat sources such as heaters

or radiators, and do not excessively bend or otherwise damage

the cord, place heavy objects on it, or place it in a position

where anyone could walk on, trip over, or roll anything over it.

●

Do not open the instrument or attempt to disassemble the inter-

nal parts or modify them in any way. The instrument contains no

user-serviceable parts. If it should appear to be malfunctioning,

discontinue use immediately and have it inspected by qualiﬁed

Yamaha service personnel.

●

Do not expose the instrument to rain, use it near water or in

damp or wet conditions, or place containers on it containing liq-

uids which might spill into any openings.

●

Never insert or remove an electric plug with wet hands.

●

Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

●

If the power cord or plug becomes frayed or damaged, or if there

is a sudden loss of sound during use of the instrument, or if any

unusual smells or smoke should appear to be caused by it,

immediately turn off the power switch, disconnect the electric

plug from the outlet, and have the instrument inspected by qual-

iﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or

others, or damage to the instrument or other property. These precautions include, but are not limited

to, the following:

●

When removing the electric plug from the instrument or an out-

let, always hold the plug itself and not the cord. Pulling by the

cord can damage it.

●

Remove the electric plug from the outlet when the instrument is

not to be used for extended periods of time, or during electrical

storms.

●

Do not connect the instrument to an electrical outlet using a

multiple-connector. Doing so can result in lower sound quality,

or possibly cause overheating in the outlet.

●

Read carefully the attached documentation explaining the

assembly process. Failure to assemble the instrument in the

proper sequence might result in damage to the instrument or

even injury.

●

Do not expose the instrument to excessive dust or vibrations, or

extreme cold or heat (such as in direct sunlight, near a heater,

or in a car during the day) to prevent the possibility of panel dis-

ﬁguration or damage to the internal components.

●

Do not use the instrument in the vicinity of a TV, radio, stereo

equipment, mobile phone, or other electric devices. Otherwise,

the instrument, TV, or radio may generate noise.

●

Do not place the instrument in an unstable position where it

might accidentally fall over.

●

Before moving the instrument, remove all connected cables.

●

Do not place the instrument against a wall (allow at least 3 cm/

one-inch from the wall), since this can cause inadequate air cir-

culation, and possibly result in the instrument overheating.

Power supply/Power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/Power cord

Assembly

Location

YDP-113

PRECAUTIONS

ENGLISH

●

Before connecting the instrument to other electronic compo-

nents, turn off the power for all components. Before turning the

power on or off for all components, set all volume levels to mini-

mum. Also, be sure to set the volumes of all components at their

minimum levels and gradually raise the volume controls while

playing the instrument to set the desired listening level.

●

When cleaning the instrument, use a soft, dry or slightly damp

cloth. Do not use paint thinners, solvents, cleaning ﬂuids, or

chemical-impregnated wiping cloths.

●

Take care that the key cover does not pinch your ﬁngers, and do

not insert a ﬁnger or hand in any gaps on the key cover or

instrument.

●

Never insert or drop paper, metallic, or other objects into the

gaps on the key cover, panel or keyboard. If this happens, turn

off the power immediately and unplug the power cord from the

AC outlet. Then have the instrument inspected by qualiﬁed

Yamaha service personnel.

●

Do not place vinyl, plastic or rubber objects on the instrument,

since this might discolor the panel or keyboard.

●

Do not rest your weight on, or place heavy objects on the instru-

ment, and do not use excessive force on the buttons, switches

or connectors.

●

Do not operate the instrument for a long period of time at a high

or uncomfortable volume level, since this can cause permanent

hearing loss. If you experience any hearing loss or ringing in the

ears, consult a physician.

●

Do not place the bench in an unstable position where it might

accidentally fall over.

●

Do not play carelessly with or stand on the bench. Using it as a

tool or step-ladder or for any other purpose might result in acci-

dent or injury.

●

Only one person should sit on the bench at a time, in order to

prevent the possibility of accident or injury.

●

If the bench screws become loose due to extensive long-term

use, tighten them periodically using the included tool.

Always turn the power off when the instrument is not in use.

Connections

Maintenance

Handling caution

Using the bench (If included)

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the instrument, or data that is lost or destroyed.

(1)B-7

2/2

YDP-113

Accessories / Maintenance

ENGLISH

Accessories

• “50 Greats for the Piano” (Music Book)

• Owner’s Manual

This manual contains complete instructions for operating your YDP-113.

• Quick Operation Guide

• Bench

A bench may be included or optional, depending on your locale.

• Damper pedal

Maintenance

Clean the instrument using a dry or slightly damp soft cloth (wring well).

CAUTION

Do not use benzene, thinner, detergent, or chemically-treated cloth for cleaning. Do not place vinyl, plastic or rubber

products on the instrument.

Otherwise, the panel or keys may become discolored or degraded.

CAUTION

Before using the YDP-113, be sure to read “Precautions” on pages 6 – 7.

Tuning

Unlike an acoustic piano, the YDP-113 does not need to be tuned. It always stays perfectly in tune.

Transporting

If you move to another location, you can transport the YDP-113 along with your other belongings. You can move the

unit as it is (assembled) or you can disassemble the unit before moving.

Tr ansport the keyboard horizontally. Do not lean it up against a wall or stand it up on its side. Do not subject the

instrument to excessive vibration or shock.

YDP-113

Features

ENGLISH

Features

The Yamaha YDP-113 digital piano offers unmatched sonic realism and natural grand-piano type playability as well as

Ya maha’s original “

AWM Stereo Sampling

” tone-generation technology for rich, musical voices, and a special “

Graded

Hammer

” keyboard that provides graded key weight and response throughout the keyboard range.

The Grand Piano 1 and 2 voices feature totally new samples painstakingly recorded from a full concert grand piano. The

E. Piano 1 voice features a single velocity-switched sample (Dynamic Sampling) and E. Piano 2 voice features two veloc-

ity-switched sample.

The YDP-113 sounds much closer to a true acoustic piano.

MASTER

VOLUME

DEMO

METRONOME

VOICE

MIN MAX

MIDI

DAMPER PEDAL

INOUTTHRU

MASTER

VOLUME

DEMO

METRONOME

VOICE

MIN MAX

POWER

PHONES

MIDI [IN/OUT/THRU]

Connect a MIDI device to this connector to

use various MIDI functions (pages 25–26).

(About MIDI—page 23)

[DAMPER PEDAL]

Connect the included

pedal here to use it as a

damper pedal (page 30).

[MASTER VOLUME]

Adjust the volume level using this control (page 11).

[DEMO]

Playback of a demo song and 50 preset songs is available (page 15).

[METRONOME]

Control the metronome functions (page 21).

[VOICE]

Select voices from 10 internal sounds, including Grand Piano 1 and 2 (page 17).

You can also combine two voices simultaneously (page 19), select various reverb

effects (page 18), etc.

[PHONES]

A set of standard stereo

headphones can be plugged

in here for private

practice (page 12).

YDP-113

Before Using the YDP-113

ENGLISH

Before Using the YDP-113

Key Cover

To open the key cover:

Lift the cover slightly, then push and slide it open.

To close the key cover:

Slide the cover toward you and gently lower the cover

over the keys.

CAUTION

Hold the cover with both hands when opening or closing it. Do not release it until it is fully opened or closed. Be care-

ful to avoid catching ﬁngers (yours or others, especially children’s) between the cover and main unit.

CAUTION

Do not place objects, such as a piece of metal or paper, on top of the key cover. Small objects placed on the key cover

may fall inside the unit when the cover is opened and may be nearly impossible to remove. This could cause electric

shock, short circuit, ﬁre or other serious damage to the instrument.

Music Rest

To raise the music rest:

Pull the music rest up and toward yourself as far as it will go.

Flip down the two metal supports at the left and right on

the rear of the music rest.

3. Lower the music rest so that it rests on the metal sup-

ports.

To lower the music rest:

1. Pull the music rest toward yourself as far as it will go.

2. Raise the two metal supports (at the rear of the music rest).

3. Gently lower the music rest backward until it is all the

way down.

CAUTION

Do not try to use the music rest in a half-raised position.

When lowering the music rest, do not release your hands

from the music rest until it is all the way down.

Be careful to avoid catching your fingers

when opening or closing the cover.

CAUTION

YDP-113 Before Using the YDP-113

ENGLISH

Turning the Power On

1. Connect the power cord.

Insert the plugs at the ends of the cord: one into the AC INLET on the YDP-113, and the other into a standard AC out-

let.

In some areas, a plug adaptor may be provided to match the pin conﬁguration of AC wall outlets in your area.

(The shape of the plug differs depending on locale.)

2. Turn the power on.

Press the [POWER] button.

•The power indicator located below the left end of the keyboard lights up.

When you’re ready to turn off the power, press the [POWER] button again.

•The power indicator turns off.

Setting the Volume

When you start playing, adjust the [MASTER VOLUME] control to the most comfortable listening level.

CAUTION

Do not use the YDP-113 at a high volume level for a long period of time, or your hearing may be damaged.

TIP

Power indicator

If you close the key cover without turning the power off, the power indicator remains lit, indicating that the

power is still on.

(bottom surface)

Power indicator

[POWER]

TERMINOLOGY

MASTER VOLUME:

The volume level of the entire keyboard sound

TIP

Yo u can also adjust the [PHONES] output level using the [MASTER VOLUME] control.

MASTER

VOLUME

MIN MAX

The level decreases. The level increases.

YDP-113 Before Using the YDP-113

ENGLISH

Using Headphones

Connect a pair of headphones to one of the [PHONES] jacks.

Two [PHONES] jacks are provided.

You can connect two sets of standard stereo headphones. (If you are

using only one pair of headphones, you can plug them into either

jack.)

Using the Headphone Hanger

A headphone hanger is included in the YDP-113 package so that you can hang

the headphones on the YDP-113. Install the headphone hanger using the

included two screws (4 × 10mm) as shown in the ﬁgure.

CAUTION

Do not hang anything other than the headphones on the hanger. Otherwise,

the YDP-113 or the hanger may be damaged.

PHONES

standard stereo

phone plug

bottom surface

PHONES

YDP-113

ENGLISH

Reference

Part Names................................................................ 14

Listening to the Demo Songs................................... 15

Listening to 50 Piano Preset Songs.......................... 16

Selecting & Playing Voices ....................................... 17

Selecting Voices ........................................................... 17

Using the Damper Pedal ............................................. 17

Adding Variations to the Sound – Reverb.................. 18

Combining Two Voices (Dual mode)......................... 19

Tr ansposition............................................................... 20

Fine-tuning the Pitch.................................................. 20

Using the Metronome................................................. 21

About MIDI.............................................................. 23

Connecting a Personal Computer ........................... 24

MIDI Functions........................................................ 26

MIDI Transmit/Receive Channel Selection ............... 26

Local Control ON/OFF............................................... 26

Program Change ON/OFF ......................................... 27

Control Change ON/OFF ........................................... 27

Troubleshooting ....................................................... 28

Options ..................................................................... 28

Keyboard Stand Assembly........................................ 29

Index ......................................................................... 31

This section explains how to make detailed settings for the

YDP-113’s various functions.

YDP113(E).book Page 13 Wednesday, April 30, 2003 10:23 AM

YDP-113 Part Names

ENGLISH

Part Names

Top panel (YDP-113)

MASTER

VOLUME

DEMO

METRONOME

VOICE

MIN MAX

POWER

MIDI

DAMPER PEDAL

INOUTTHRU

PHONES

MASTER

VOLUME

DEMO

METRONOME

VOICE

MIN MAX

C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4

E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7

B-1A-1

1 [POWER] ....................................... P11

2 [MASTER VOLUME]....................... P11

3 [DEMO] ........................................ P15

4 [METRONOME]............................. P21

5 [VOICE]....................................P17–19

6 [PHONES] ..................................... P12

7 [DAMPER PEDAL] .................... P17, 30

8 MIDI [IN] [OUT] [THRU]................ P23

9 Damper pedal......................... P17, 30

YDP-113

Listening to the Demo Songs

ENGLISH

Listening to the Demo Songs

Demo songs are provided that effectively demonstrate each of the YDP-113’s voices.

Turn on the power.

(In case the power is not turned ON) Press the

[POWER]

button.

When you start playing, adjust the

[MASTER VOLUME]

control to the most

comfortable listening level.

Engage Demo mode.

Press the

[DEMO]

button to engage Demo mode. The

[DEMO]

button indicator

will light.

Play a Voice demo.

While holding down the

[DEMO]

button, press one of the C1–A1 keys to select

and start the corresponding demo song. Starting with the selected tune, the

demo songs will play in sequence until stopped.

Demo Song List

songs listed below.

Refer to the voice list on page 17 for voice key assignments.

The demo songs listed below are short re-arranged excerpts from the original

compositions.

Adjusting the Volume

Use the

[MASTER VOLUME]

control to adjust the volume.

Stop the Voice demo.

Press the

[DEMO]

button to stop playback.

Procedure

NOTE

Refer to the voice list on

page 17 for more information on

the characteristics of each pre-

set voice.

TERMINOLOGY

Mode:

A mode is a condition or status

under which you can execute a

certain function. In Demo mode,

you can play back demo songs.

NOTE

You cannot adjust the tempo of

demo songs.

KeyVoice Name Title Composer

C1 GrandPiano1 Consolation No.3 F. Liszt

E1 Harpsichord1 Gavotte J.S. Bach

F1 Harpsichord2 Invention No.1 J.S. Bach

The lowest key

DEMO

YDP113(E).book Page 15 Wednesday, April 30, 2003 10:23 AM

YDP-113 Listening to 50 Piano Preset Songs

ENGLISH

Listening to 50 Piano Preset Songs

The YDP-113 provides performance data for 50 piano songs. You can simply listen to these songs.

You can also refer to the included “50 Greats for the Piano” that contains scores for 50 piano preset

songs.

1. Engage Preset Song mode.

Press the [DEMO] button to engage Preset Song mode. The [DEMO] button

indicator will light.

2. Play a preset song.

While holding down the [DEMO] button, press one of the C2–C



6 keys to select

and start the corresponding tune. To play all preset songs in sequence, while

holding down the [DEMO] button, press the D6 key.

Adjusting the Volume

Use the [MASTER VOLUME] control to adjust the volume.

3. Stop playback.

Playback will stop automatically when the selected preset song has ﬁnished. To

stop the song during playback (or continuous playback), press the [DEMO] but-

ton.

•To continue playing other songs, see procedure 2 above.

Procedure

TERMINOLOGY

Song:

On the YDP-113, performance

data is called a “Song.” This

includes demo songs and piano

preset tunes.

TIP

You can play the keyboard

along with the preset song. You

can change the voice playing on

the keyboard.

TIP

You can adjust the Reverb type

(page 18) that is applied to the

voice you play on the keyboard

and to the preset song play-

back.

NOTE

The default tempo is automati-

cally selected whenever a new

preset song is selected, and

when a new preset song begins

playback.

NOTE

To adjust the tempo of the preset

song playback, see page 21.

NOTE

When you select a different song

(or a different song is selected

during chained playback), an

appropriate reverb type will be

selected accordingly.

NOTE

MIDI reception is not possible in

Piano Song mode. Piano song

data is not transmitted via the

MIDI connectors.

C2 D6

C 6



The highest key

DEMO

YDP-113 Selecting & Playing Voices

ENGLISH

Selecting & Playing Voices

Selecting Voices

While holding down the [VOICE] button, press one of the C1–A1 keys to select and

start the corresponding voice.

Then, when you start playing, adjust the [MASTER VOLUME] control to the most com-

fortable listening level.

Using the Damper Pedal

You can connect the damper pedal to the YDP-113

(page 30).

The damper pedal functions in the same way as a

damper pedal on an acoustic piano. When the

damper pedal is pressed, notes sustain longer.

Releasing the pedal immediately stops (damps) any

sustained notes.

Procedure

TIP

To understand the characteris-

tics of various voices, listen to

demo songs for each voice

(page 15).

TERMINOLOGY

Voice:

On the YDP-113, a voice

means a “tone” or “tonal color.”

NOTE

Selecting a voice automatically

engages the best-suited reverb

type and depth (page 18) for

that particular voice.

KeyVoice Name Description

C1 Grand Piano 1

Recorded samples from a full concert grand piano. Perfect for classical

compositions as well as any other style that requires acoustic piano.



1Grand Piano 2 Spacious and clear piano with bright reverb. Good for popular music.

D1 E.Piano 1 An electronic piano sound created by FM synthesis. Good for popu-

lar music.



1 E.Piano 2

The sound of an electric piano using hammer-struck metallic “tines.” Soft

tone when played lightly, and an aggressive tone when played hard.

E1 Harpsichord 1 The deﬁnitive instrument for baroque music. Since harpsichord uses

plucked strings, there is no touch response.

F1 Harpsichord 2 Mixes the same voice an octave higher for a more brilliant tone.



1 Vibraphone Vibraphone played with relatively soft mallets. It has a tremolo effect

that is typical for vibraphone.

Church Organ 1

This is a typical pipe organ sound (8 feet + 4 feet + 2 feet). Good for

sacred music from the Baroque period.



Church Organ 2

This is the organ’s full coupler sound, often associated with Bach’s

“Toccata and Fugue”.

A1 Strings Spacious and large-scale string ensemble. Try combining this voice

with piano in DUAL mode.

C1 D1 E1 F1 G1 A1

C 1



D 1



F 1



G 1



The lowest key

VOICE















When you press the damper

pedal here, the notes you play

before you release the pedal

sustain longer.

NOTE

If the damper pedal doesn’t

work, make sure that the pedal

cord is properly plugged into the

main unit (page 30).

NOTE

Make sure that the damper

pedal is not pressed when you

turn on the power to the unit,

connect or disconnect the

pedal.

NOTE

Make sure that you turn off the

power to the unit before you

connect or disconnect the

pedal.

YDP-113 Selecting & Playing Voices

ENGLISH

Adding Variations to the Sound – Reverb

This control enables you to select various digital reverb effects that add extra depth and expression

to the sound to create a realistic acoustic ambience.

When you select a reverb, the reverb is automatically turned on.

While holding down the [VOICE] button, press one of the C2–E2 keys to select a reverb

type.

Adjusting Reverb Depth

Adjust the reverb depth for the selected voice by pressing one of the C3–G



4 keys while

holding down the [VOICE] button. The depth range is from 0 through 20.

Procedure

KeyReverb Type Description

C2 Room This setting adds a continuous reverb effect to the sound, similar to

the acoustic reverberation you would hear in a room.



2 Hall1 For a “bigger” reverb sound, use the HALL 1 setting. This effect sim-

ulates the natural reverberation of a small-size concert hall.

D2 Hall2 For a truly spacious reverb sound, use the HALL 2 setting. This effect

simulates the natural reverberation of a large concert hall.



2 Stage Simulates the reverb of a stage environment.

E2 Off No effect is applied.

C2 D2 E2

C 2



D 2



The lowest key

VOICE

TIP

The default reverb type (includ-

ing OFF) and depth settings are

different for each voice.

TIP

depth 0: no effect

depth 20: maximum reverb

depth

C3: depth 0

G 4: depth 20



The lowest key

VOICE

The depth value increases as you press higher keys.

YDP-113 Selecting & Playing Voices

ENGLISH

Combining Two Voices (Dual mode)

You can play two voices simultaneously across the entire range of the keyboard. In this way, you

can simulate a melody duet or combine two similar voices to create a thicker sound.

1. Engage Dual mode.

While holding down the [VOICE] button, press two of the C1–A1 keys at simul-

taneously (or press one key while holding another).

Refer to the voice list on page 17 for available voices.

According to the voice priority shown in the voice list (page 17), the voice

assigned to the lower keyboard will be designated as Voice 1 (the other voice will

be designated as Voice 2).

You can make the following settings only in Dual mode:

Setting the Octave

You can shift the pitch up and down in octave steps for Voice 1 and Voice 2 inde-

pendently. Depending on which voices you combine in Dual mode, the combi-

nation may sound better if one of the voices is shifted up or down an octave.

While holding down the [VOICE] button, press one of the C5–F5 keys.

Setting the Balance

You can set one voice as the main voice, and another voice as a softer, mixed voice.

While holding down the [VOICE] button, press one of the F



5–F



6 keys.

A setting of “0” produces an equal balance between the two Dual mode voices.

Settings below “0” increases the volume of Voice 2 in relation to Voice 1, and set-

tings above “0” increases the volume of Voice 1 in relation to Voice 2.

2. Exit Dual mode and return to normal play mode.

While holding down the [VOICE] button, press one of the C1–A1 keys.

Procedure

NOTE

You cannot assign the same

voice to Voice 1 and Voice 2

simultaneously in Dual mode.

TIP

Reverb in Dual Mode

The reverb type assigned to

Voice 1 will take priority over the

other. (If the reverb is set to

OFF, Voice 2 reverb type will be

in effect.) Reverb depth setting

(

page 18

) will be applied only to

Voice 1.

C1 A1

The lowest key

VOICE

C5 F5

VOICE

The highest key

For setting

the octave. (C5–F5)

C5 key: –1 (Voice 1), C



5 key: 0 (Voice 1), D5 key: +1(Voice 1),



5 key: –1 (Voice 2), E5 key: 0 (Voice 2), F5 key: +1(Voice 2)



F 6



-5

-6 -4 -2

+1 +3 +6

-3 -1 0 +2 +4 +5

VOICE

The highest key

For setting the balance. (F



5–F



YDP-113 Selecting & Playing Voices

ENGLISH

Transposition

The YDP-113’s Transpose function makes it possible to shift the pitch of the entire keyboard up or

down in semitone intervals up to a maximum of six semitones, and lets you easily match the pitch

of the keyboard to the range of a singer or other instruments.

For example, if you set the transposition amount to “5,” playing key C produces pitch F. In this way,

you can play a song as though it were in C major, and the YDP-113 will transpose it to the key of F.

While holding down the A-1 andC



0 keys, press one of the F



2–F



3 keys to set the

desired amount of transposition.

Pressing the C3 key produces normal keyboard pitch. Pressing the key to the left of C3

(=B2) transposes the pitch of the keyboard down a semitone, the next key to the left

(=Bb2) transposes down a whole tone (two semitones), etc., down to the F



2 key,

which transposes down six semitones. Upward transposition is accomplished in the

same way using the keys to the right of C3, up to F



3, which transposes up six semi-

tones.

Fine-tuning the Pitch

You can ﬁne-tune the pitch of the entire instrument. This function is useful when you play the YDP-

113 along with other instruments or CD music.

To tune up (in about 0.2Hz steps):

Hold down the A-1 and

B-1

keys simultaneously and press any key between C3 and B3.

To tune down (in about 0.2Hz steps):

Hold down the A-1 and



-1

keys simultaneously and press any key between C3 and

B3.

To restore standard pitch:

Hold down the A-1, A



-1 and B-1 simultaneously and press any key between C3 and B3.

Setting range: 427.0-453.0 Hz

Standard pitch: 440.0 Hz

Procedure

TERMINOLOGY

Transpose:

Changing the key signature of a

song. On the YDP-113, trans-

posing shifts the pitch of the

entire keyboard.

TIP

Notes below and above the A-1

.... C7 range of the YDP-113

sound one octave higher and

lower, respectively.

-1

Normal

pitch.

Transpose

down.

Transpose

up.

-5 -3 -1 0 +2 +4 +5

-6 -4 -2 +1

+3 +6



TERMINOLOGY

Hz (Hertz):

This unit of measurement refers

to the frequency of a sound and

represents the number of times

a sound wave vibrates in a sec-

ond.

Procedure

C3 B3

A-1 B-1

A-1

-1



-1



A-1 B-1

To tune up To tune down To restore standard pitch

YDP-113 Selecting & Playing Voices

ENGLISH

Using the Metronome

The YDP-113 features a built-in metronome (a device that keeps an accurate tempo) that is conve-

nient for practicing.

1. Start the metronome.

Press the [METRONOME] button to turn on the metronome.

Determines the time signature

While holding down the [METRONOME] button, press one of the C3–F3 keys.

Adjusting the tempo

The tempo of the metronome and preset song playback can be set from 32 to

280 beats per minute.

While holding down the [METRONOME] button, press a sequence of C4–A4

keys to specify a three-digit number.

Select a number starting from the left-most digit. For example, to set the tempo

“95,” press the C4 (0), A4 (9) and F4 (5) keys in sequence.

To increase the tempo value in steps of one, while holding down the [METRO-

NOME]

button, press the C



5 key. To decrease the tempo value in steps of one,

while holding down the

[METRONOME] button, press the B4 key.

To increase the tempo value in steps of ten, while holding down the [METRO-

NOME]

button, press the D5 key. To decrease the tempo value in steps of ten,

while holding down the

[METRONOME] button, press the A



4 key.

To set the default tempo (the metronome’s original tempo or the song’s original

tempo), while holding down the

[METRONOME] button, press the C5 key.

Procedure

NOTE

During preset song playback,

you can set the tempo from 20

to 400 beats per minute,

depending on the song data.



METRONOME

The highest key

C3 key: No downbeat, C



3 key: 2/4, D3 key: 3/4, D



3 key: 4/4, E3 key: 5/4, F3 key: 6/4

C4 A4

METRONOME

The highest key

024579

8631

B4 C5 D5



METRONOME

The highest key

YDP-113 Selecting & Playing Voices

ENGLISH

Adjusting the volume

You can change the volume of the metronome sound.

While holding down the [METRONOME] button, press one of the C1–G2 keys

to determine the volume.

2. Stop the metronome.

Turn off the metronome by pressing the [METRONOME] button.

C1 G2

METRONOME

The lowest key

The volume level increases as you press higher keys.

YDP-113 About MIDI

ENGLISH

About MIDI

MIDI (Musical Instrument Digital Interface) is a standard format for

data transmission and reception. It enables the transfer of performance

data and commands between MIDI devices and personal computers.

Using MIDI, you can control a connected MIDI device from the YDP-

113, or control the YDP-113 from a connected MIDI device or com-

puter.

MIDI connectors

MIDI [IN]: Receives MIDI data.

MIDI [OUT]: Tr ansmits MIDI data.

MIDI [THRU]: Tr ansmits data received at the MIDI [IN] connector, passing it through

the unit unmodiﬁed.

MIDI cables

Prepare dedicated MIDI cables.

TIP

MIDI performance data and

commands are transferred in

the form of numeric values.

TIP

Since MIDI data that can be

transmitted or received varies

depending on the type of MIDI

device, check the “MIDI Imple-

mentation Chart” to ﬁnd out

what MIDI data and commands

your devices can transmit or

receive. The YDP-113’s MIDI

Implementation Chart appears

on page 38.

MIDI

INOUTTHRU

TIP

You can also obtain detailed

information about MIDI from

various music books and other

publications.

YDP-113 Connecting a Personal Computer

ENGLISH

Connecting a Personal Computer

You can enjoy computer music data on the YDP-113 by connecting a computer to the MIDI jack.

There are two methods by which to connect the YDP-113 to a personal computer:

1. Use a MIDI interface and the YDP-113’s MIDI connectors (page 25).

2. Use the USB port on the computer and a USB interface (model UX16, UX96, or UX256) (page 25).

NOTE

When the YDP-113 is used as a tone module, performance data with voices that are not found on the YDP-113 will not

be played correctly.

“The Clavinova-Computer Connection,” is a supplementary guidebook that describes, for beginners, what you

can do with your YDP-113 and a personal computer and how to set up a YDP-113-Computer system (although the

guidebook only mentions the Clavinova, it applies equally to the YDP-113 digital piano). The document is available as

a PDF ﬁle (in English) at the following Internet address:

Clavinova Web site (English only):

http://www.yamahaclavinova.com/

Yamaha Manual Library :

http://www2.yamaha.co.jp/manual/english/

NOTE

Before you connect the YDP-113 to a personal computer, ﬁrst turn off the power to both the YDP-113 and the computer.

After you make the connections, turn on the power to the computer ﬁrst, then turn on the power to the YDP-113.

YDP-113 Connecting a Personal Computer

ENGLISH

1. Using a MIDI interface and the YDP-113’s MIDI connectors

Connection

Use a MIDI interface to connect a computer to the YDP-113 using special MIDI cables.

2. Connecting the computer’s USB port to the YDP-113 via a USB interface, such as

the UX16, UX96, or UX256

Connect the computer’s USB port to the USB interface (such as the UX16, UX96, or UX256) using a USB cable. Install

the driver (that came with the USB interface) on the computer, and connect the USB interface to the YDP-113 using a

serial cable or MIDI cables.

For more information, refer to the instruction manual for the USB interface.

An example of connecting the USB interface to the YDP-113 using MIDI cables

MIDI OUT

MIDI

OUT

MIDI

OUT

MIDI

Windows Macintosh

YDP-113

MIDI interface

MIDI

INOUTTHRU

USB cable

MIDI cables

YDP-113

USB interface

computer

MIDI

INOUTTHRU

MASTER

VOLUME

DEMO

METRONOME

VOICE

MIN MAX

POWER

YDP-113 MIDI Functions

ENGLISH

MIDI Functions

You can make detailed adjustments to MIDI settings.

For more information about MIDI, see the “About MIDI” section (page 23).

MIDI Transmit/Receive Channel Selection

In any MIDI control setup, the MIDI channels of the transmitting and receiving equip-

ment must be matched for proper data transfer.

This parameter enables you to specify the channel on which the YDP-113 transmits or

receives MIDI data.

Setting the transmit channel

While holding down the A-1 and C



0 keys, press one of the C1–E2 keys.

Setting the receive channel

While holding down the A-1 and C



0 keys, press one of the C4–F5 keys.

Local Control ON/OFF

“Local Control” refers to the fact that, normally, the YDP-113 keyboard controls its

internal tone generator, allowing the internal voices to be played directly from the key-

board. This situation is “Local Control On,” since the internal tone generator is con-

trolled locally by its own keyboard.

Local control can be turned OFF, however, so that the YDP-113 keyboard does not play

the internal voices, but the appropriate MIDI information is still transmitted via the

MIDI OUT connector when notes are played on the keyboard. At the same time, the

internal tone generator responds to MIDI information received via the MIDI IN con-

nector.

While holding down the A-1 and C



0 keys, press the C6 key.

NOTE

Demo and preset song data are

not transmitted via MIDI.

NOTE

In Dual mode, Voice 1 data is

transmitted on its speciﬁed

channel and Voice 2 data is

transmitted on the next greater

channel number relative to the

speciﬁed channel. In this mode,

no data is transmitted if the

transmit channel is set to “OFF.”

TIP

ALL:

A “Multi-timbre” Receive mode

is available. It allows simulta-

neous reception of different

parts on all 16 MIDI channels,

enabling the YDP-113 to play

multi-channel song data

received from a music computer

or sequencer.

1+2:

A “1+2” Receive mode is avail-

able. It allows simultaneous

reception on channels 1 and 2

only, enabling the YDP-113 to

play 1 and 2 channel song data

received from a music computer

or sequencer.

TIP

Program change and other like

channel messages received will

not affect the YDP-113’s panel

settings or the notes you play

on the keyboard.

NOTE

The YDP-113 does not receive

MIDI data when it is in Demo or

Preset Song mode.

Procedure

A-1 C1 C4 F5

OFF



1356810

24 7911 1416

12 1315

For ALL mode

1356810

24 7911 1416

12 1315

1+2

For setting the

transmit channels.

(C1–D

For setting the

receive channels.

(C4–F5)

A-1 C



The highest

key

YDP-113 MIDI Functions

ENGLISH

Program Change ON/OFF

Normally the YDP-113 will respond to MIDI program change numbers received from

an external keyboard or other MIDI device, causing the correspondingly-numbered

voice to be selected on the corresponding channel (the keyboard voice does not

change). The YDP-113 will normally also send a MIDI program change number when-

ever one of its voices is selected, causing the correspondingly-numbered voice or pro-

gram to be selected on the external MIDI device if the device is set up to receive and

respond to MIDI program change numbers.

This function makes it possible to cancel program change number reception and trans-

mission so that voices can be selected on the YDP-113 without affecting the external

MIDI device.

While holding down the A-1 and C



0 keys, press the C



6 key.

Control Change ON/OFF

Normally the YDP-113 will respond to MIDI control change data received from an

external MIDI device or keyboard, causing the voice on the corresponding channel to

be affected by pedal and other “control” settings received from the controlling device

(the keyboard voice is not affected). The YDP-113 also transmits MIDI control change

information when the pedal or other appropriate controls are operated.

This function makes it possible to cancel control change data reception and transmis-

sion so that, for example, the YDP-113’s pedal and other controls can be operated with-

out affecting an external MIDI device.

While holding down the A-1 and C



0 keys, press the D6 key.

TIP

For information on program

change numbers for each of the

YDP-113’s voices, refer to page

34 in the MIDI Data Format sec-

tion.

Procedure

A-1 C



The highest

key

TIP

For information on control

changes that can be used with

the YDP-113, refer to the MIDI

Data Format on page 34.

Procedure

A-1 C



The highest

key

YDP-113

Troubleshooting

ENGLISH

Troubleshooting

Options

BC-100 Bench

A comfortable bench styled to match your Yamaha YDP-113.

HPE-160 Stereo Headphones

High-performance lightweight dynamic headphones with extra-soft ear pads.

Problem Possible Cause and Solution

The YDP-113 does not turn on. The YDP-113 has not been plugged in properly. Securely insert the female plug into

the socket on the YDP-113, and the male plug into a proper AC outlet (page 11).

A click or pop is heard when the power is

turned on or off.

This is normal when electrical current is being applied to the instrument.

Noise from the speakers or headphones is

audible.

The noise may be due to interference caused by the use of a mobile phone in close

proximity to the YDP-113. Turn off the mobile phone, or move it further away from the

YDP-113.

The overall volume is low, or no sound is

heard.

• The Master Volume is set too low. Set it to an appropriate level using the [MASTER

VOLUME] control.

• Make sure a pair of headphones is not connected to the headphones jack.

• Make sure that Local Control (page 26) is ON.

The damper pedal has no effect, or the sound

continuously sustains even when the damper

pedal is not pressed.

The pedal cord may not be properly connected. Make sure to securely insert the pedal

cord into the [DAMPER PEDAL] jack (page 30).

YDP-113

Troubleshooting/Options

YDP113(E).book Page 28 Wednesday, April 30, 2003 10:24 AM

YDP-113 Keyboard Stand Assembly

ENGLISH

Keyboard Stand Assembly

CAUTION

Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accor-

dance with the sequence given below.

• Assembly should be carried out by at least two persons.

• Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage.

• Be sure to tighten up all screws upon completing assembly of each unit.

•To disassemble, reverse the assembly sequence given below.

Remove the following parts from the package.

1. Attach the center panel (B) to the side

panels (C).

The center panel (B) is installed between the side pan-

els (C). The brackets on each end of the center panel

should face the rear of the stand assembly. Place the

square holes in the center-panel brackets over the lugs

extending from the side panels, then slide down the

center panel. Each side of the center panel is attached

using two 6 × 16 mm ﬂat-head screws.

2. Install the main unit (A).

CAUTION

• Fingers can become pinched between the main

unit and the rear or side panels, be extra careful so

as not to drop the main unit.

• Do not hold the keyboard in any position other

than the position shown in the illustration.

Place the main unit (A) on the side panels (C) with the

screws on its bottom panel (toward the rear of the main

unit) just behind the grooves in the brackets located at

the top of the side panels. Then slide the main unit for-

ward until it stops.

Align the holes in the bottom panel of the main unit

with the holes in the brackets on the side panels. (C

en-

ter the main unit to produce equal clearance on the left

and right sides, as shown in the illustration.) Then use

the four 6 × 16 mm ﬂat-head screws to attach the main

unit. Two screws can be attached from the front side

and two screws from the rear.

Have a Phillips-head (+) screwdriver ready

Assembly Parts

6 × 16 mm flat-head screws ×8

Cord holders ×2

Damper pedal

AC power cord

6 x 16 mm flat-head screw

NOTE

If the holes of the front side brackets are not aligned with the

screw hole, position the sides of the side panels so that they

are parallel with the side of the unit.

10 cm

6 x 16 mm flat-head screw

Be sure to place your

hands at least 10 cm

from either end of the

main unit when posi-

tioning it.

YDP-113 Keyboard Stand Assembly

ENGLISH

3. Set the voltage selector and connect the

power cord.

Before connecting the AC power cord, check the setting

of the voltage selector which is provided in some areas.

To set the selector for 110V, 127V, 220V or 240V main

voltages, use a “minus” screwdriver to rotate the selec-

tor dial so that the correct voltage for your region

appears next to the pointer on the panel. The voltage

selector is set at 240V when the unit is initially shipped.

After the proper voltage has been selected, connect the

AC power cord to the AC INLET and an AC wall outlet.

A plug adaptor may be also provided in some areas to

match the pin conﬁguration of the AC wall outlets in

your area.

WARNING

An improper voltage setting can cause serious

damage to the YDP-113 or result in improper

operation.

• Connecting the damper pedal

To use the pedal functions, connect the included

damper pedal to the YDP-113.

Connect the pedal cord to the [DAMPER PEDAL]

jack on the bottom of the YDP-113.

Attach two cord holders on the YDP-113 as shown in

the illustration, then clip the cord into the holders.

After completing the assembly, please

check the following.

When moving the instrument after assembly, always

hold the bottom of the main unit.

CAUTION

• Do not hold the key cover or top portion.

Improper handling can result in damage to the

instrument or personal injury.

240

127

110

220

A voltage selector is provided in some areas.

DAMPER PEDAL

• Are there any parts left over?

➝Review the assembly procedure and correct any

errors.

• Is the YDP-113 clear of doors and other movable

ﬁxtures?

➝Move the YDP-113 to an appropriate location.

• Does the YDP-113 make a rattling noise when

you shake it?

➝Tighten all screws.

• Are the pedal and power cords inserted securely

into the sockets?

➝Check the connection.

• If the main unit creaks or is otherwise unsteady

when you play the keyboard, refer to the assem-

bly diagrams and re-tighten all screws.

Key cover

Top portion

YDP-113 Index

ENGLISH

Index

Numerics

50 Greats for the Piano ...................................................16

50 Piano Preset Songs .....................................................16

Accessories.........................................................................8

Adjust

Reverb Depth.............................................................18

Tempo (metronome) ................................................21

Volume (50 Piano Preset Songs) ..............................16

Volume (Demo) ........................................................15

Volume (metronome)...............................................22

Assembly....................................................................29–30

Combining Two Voices (Dual mode)............................19

Connecting a Personal Computer..................................24

DAMPER PEDAL................................................14, 17, 30

DEMO........................................................................14, 15

Dual mode .......................................................................19

Key Cover ........................................................................10

MASTER VOLUME..................................................11, 14

METRONOME .........................................................14, 21

MIDI ................................................................................23

MIDI [IN] [OUT] [THRU]............................................14

MIDI cables ...............................................................23, 25

MIDI connectors.......................................................23, 25

MIDI Data Format ..........................................................34

MIDI Implementation Chart..........................................38

Music Rest........................................................................10

PHONES.................................................................... 12, 14

POWER .....................................................................11, 14

Precautions....................................................................6–7

Preset songs ➝ 50 Piano Preset Songs........................... 16

Reverb..............................................................................18

Song .................................................................................16

Specifications................................................................... 39

Start/Stop playback

50 Piano Preset Songs ............................................... 16

Demo Songs...............................................................15

Transporting .....................................................................8

Transposition ..................................................................20

Troubleshooting.............................................................. 28

VOICE .................................................................14, 17–19

YDP-113 Index

ENGLISH

MEMO

YDP-113

Appendix/Anhang/

Annexe/Apéndice

This section introduces reference material.

In diesem Abschnitt ﬁnden Sie Referenzmaterial.

Cette section présente le matériel de référence.

En esta sección se incluye material de referencia.

MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI................... 34

MIDI Implementation Chart / MIDI Implementierung stabelle /

Feuille d’implantation MIDI / Gráﬁca de implementación MIDI ................................................................... 38

Speciﬁcations / Technische Daten / Caractéristiques techniques / Especiﬁcaciones .......................................... 39

YDP-113

Appendix/Anhang/Annexe/Apéndice

MIDI Data Format / MIDI-Datenformat /

Format des données MIDI / Formato de datos MIDI

If you’re already very familiar with MIDI, or are using a

computer to control your music hardware with computer-

gener-ated MIDI messages, the data provided in this section

can help you to control the YDP-113.

Falls Sie bereits mit MIDI vertraut sind oder einen

Computer zur Erzeugung von MIDI-Steuermeldungen für die

Instrumente verwenden, können Sie sich zur Steuerung des

YDP-113 nach den im folgenden Abschnitt aufgeführten

Speziﬁkationen richten.

Si vous êtes très familier avec l’interface MIDI ou si vous

utilisez un ordinateur pour commander votre matériel de

musique au moyen de messages MIDI générés par

ordinateur, les données suivantes vous seront utiles et vous

aideront à commander le YDP-113.

SI usted está ya familiarizado con MIDI, o si emplea una

computadora para controlar sus aparatos musicales con

mensajes MIDI generados por computadora, los datos

proporcionados en esta sección le ayudarán a controlar la

YDP-113.

1. NOTE ON/OFF

Data format: [9nH] -> [kk] -> [vv]

9nH = Note ON/OFF event (n = channel number)

kk = Note number (Transmit: 09H ~ 78H = A-2 ~ C8 /

Receive: 00H ~ 7FH = C-2 ~ G8)*

vv = Velocity (Key ON = 01H ~ 7FH, Key OFF = 00H)

Data format: [8nH] -> [kk] -> [vv] (reception only)

8nH = Note OFF event (n = channel number)

kk = Note number: 00H ~ 7FH = C-2 ~ G8

vv = Velocity

* If received value exceeds the supported range for the

selected voice, the note is adjusted by the necessary num-

ber of octaves.

2. CONTROL CHANGE

Data format: [BnH] -> [cc] -> [vv]

BnH = Control change (n = channel number)

cc = Control number

vv = Data Range

(1) Bank Select

ccH Parameter Data Range (vvH)

00H Bank Select MSB 00H:Normal

20H Bank Select LSB 00H...7FH

Bank selection processing does not occur until receipt of

next Program Change message.

(2) Main Volume (reception only)

ccH Parameter Data Range (vvH)

07H Volume MSB 00H...7FH

(3) Expression (reception only)

ccH Parameter Data Range (vvH)

0BH Expression MSB 00H...7FH

(4) Damper

ccH Parameter Data Range (vvH)

40H Damper MSB 00H...7FH

(5) Sostenuto (reception only)

ccH Parameter Data Range (vvH)

42H Sostenuto 00H-3FH:off, 40H-7FH:on

(6) Soft Pedal (reception only)

ccH Parameter Data Range (vvH)

43H Soft Pedal 00H-3FH:off, 40H-7FH:on

(7) Effect1 Depth (Reverb Send Level)

ccH Parameter Data Range (vvH)

5BH Effect1 Depth 00H...7FH

Adjusts the reverb send level.

(8) Effect4 Depth (Variation Effect Send Level) (reception

only)

ccH Parameter Data Range (vvH)

5EH Effect4 Depth 00H...7FH

3. MODE MESSAGES

Data format: [BnH] -> [cc] -> [vv]

BnH = Control event (n = channel number)

cc = Control number

vv = Data Range

(1) All Sound Off

ccH Parameter Data Range (vvH)

78H All Sound Off 00H

(2) Reset All Controllers

ccH Parameter Data Range (vvH)

79H Reset All Controllers 00H

Resets controllers as follows.

Controller Value

Expression 127 (max)

Damper Pedal 0 (off)

Sostenuto 0 (off)

Soft Pedal 0 (off)

(3) Local Control (reception only)

ccH Parameter Data Range (vvH)

7AH Local Control 00H (off), 7FH (on)

(4) All Notes Off

ccH Parameter Data Range (vvH)

7BH All Notes Off 00H

Switches OFF all the notes that are currently ON on the spec-

iﬁed channel. Any notes being held by the damper or soste-

nuto pedal will continue to sound until the pedal is released.

(5) Omni Off (reception only)

ccH Parameter Data Range (vvH)

7CH Omni Off 00H

Same processing as for All Notes Off.

(6) Omni On (reception only)

ccH Parameter Data Range (vvH)

7DH Omni On 00H

Same processing as for All Notes Off.

(7) Mono (reception only)

ccH Parameter Data Range (vvH)

7EH Mono 00H

Same processing as for All Sound Off.

(8) Poly (reception only)

ccH Parameter Data Range (vvH)

7FH Poly 00H

Same processing as for All Sound Off.

• When control change reception is turned OFF in the Function

mode, control change data will not be transmitted or received

except for Bank Select and Mode messages.

• Local on/off, OMNI on/off are not transmitted. (The appropriate

note off number is supplied with “All Note Off” transmission).

• When a voice bank MSB/LSB is received, the number is

stored in the internal buffer regardless of the received order,

then the stored value is used to select the appropriate voice

when a program change message is received.

• The Multi-timbre and Poly modes are always active. No

change occurs when OMNI ON, OMNI OFF, MONO, or POLY

mode messages are received.

YDP113(E).book Page 34 Wednesday, April 30, 2003 10:24 AM

YDP-113

Appendix/Anhang/Annexe/Apéndice

4. PROGRAM CHANGE

Data format: [CnH] -> [ppH]

CnH = Program event (n = channel number)

ppH = Program change number

P. C .#=Program Change number

• When program change reception is turned OFF in the Func-

tion mode, no program change data is transmitted or

received. Also, Bank MSB/LSB is not transmitted or received.

• When you specify a program change as a number in the

range of 0-127, specify a number that is one less than the

program change number listed above. For example, to specify

program change number 1, you would specify program

change 0.

5. SYSTEM REALTIME MESSAGES

[rrH]

FEH: Active sensing

• Caution: If an error occurs during MIDI reception, the Damper,

Sostenuto, and Soft effects for all channels are turned off and

an All Note Off occurs.

6. SYSTEM EXCLUSIVE MESSAGES

(Universal System Exclusive)

(1) Universal Realtime Message

Data format: [F0H] -> [7FH] -> [XnH] -> [04H] -> [01H] ->

[llH] -> [mmH] -> [F7H]

MIDI Master Volume

• Simultaneously changes the volume of all channels.

• When a MIDI master volume message is received, the volume

only has affect on the MIDI receive channel, not the panel

master volume.

F0H = Exclusive status

7FH = Universal Realtime

7FH = ID of target device

04H = Sub-ID #1=Device Control Message

01H = Sub-ID #2=Master Volume

H = Volume LSB

mmH =

Volume MSB

F7H = End of Exclusive

F0H = Exclusive status

7FH = Universal Realtime

XnH = When n is received n=0~F, whichever is received.

X = don’t care

04H = Sub-ID #1=Device Control Message

01H = Sub-ID #2=Master Volume

H = Volume LSB

mmH =

Volume MSB

F7H = End of Exclusive

(2) Universal Non-Realtime Message (GM On)

General MIDI Mode On

Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->

[F7H]

F0H = Exclusive status

7EH = Universal Non-Realtime

7FH = ID of target device

09H = Sub-ID #1=General MIDI Message

01H = Sub-ID #2=General MIDI On

F7H = End of Exclusive

F0H = Exclusive status

7EH = Universal Non-Realtime

XnH = When received, n=0~F.

X = don’t care

09H = Sub-ID #1=General MIDI Message

01H = Sub-ID #2=General MIDI On

F7H = End of Exclusive

When the General MIDI mode ON message is received, the

MIDI system will be reset to its default settings.

This message requires approximately 50ms to execute, so

sufﬁcient time should be allowed before the next message is

sent.

YDP-113 MSB LSB

P.C.#

Grand Piano 1 0 122 1

Grand Piano 2 0 112 1

E.Piano 1 0 122 6

E.Piano 2 0 122 5

Harpsichord 1 0 122 7

Harpsichord 2 0 123 7

Vibraphone 0 122 12

Church Organ 1 0 123 20

Church Organ 2 0 122 20

Strings 0 122 49

Data Transmission Reception

FEH

Transmitted every

200 milliseconds

If a signal is not received via MIDI for

more than 400 milliseconds, the

same processing will take place for

All Sound Off, All Notes Off and Reset

All Controllers as when those signals

are received.

YDP113(E).book Page 35 Tuesday, May 6, 2003 11:59 AM

YDP-113 Appendix/Anhang/Annexe/Apéndice

7. SYSTEM EXCLUSIVE MESSAGES (XG Standard)

(1) XG Native Parameter Change

Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->

[mmH] -> [llH] -> [ddH] -> [F7H]

F0H = Exclusive status

43H = YAMAHA ID

1nH = When received, n=0~F.

When transmitted, n=0.

4CH = Model ID of XG

hhH = Address High

mmH =

Address Mid

llH = Address Low

ddH = Data

F7H = End of Exclusive

Data size must match parameter size (2 or 4 bytes).

When the XG System On message is received, the MIDI sys-

tem will be reset to its default settings.

The message requires approximately 50ms to execute, so

sufﬁcient time should be allowed before the next message is

sent.

(2) XG Native Bulk Data (reception only)

Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->

[bbH] -> [hhH] -> [mmH] -> [llH] ->[ddH] ->...->

[ccH] -> [F7H]

F0H = Exclusive status

43H = YAMAHA ID

0nH = When received, n=0~F.

When transmitted, n=0.

4CH = Model ID of XG

aaH = ByteCount

bbH = ByteCount

hhH = Address High

mmH =

Address Mid

llH = Address Low

ddH = Data

| |

ccH = Check sum

F7H = End of Exclusive

• Receipt of the XG SYSTEM ON message causes reinitializa-

tion of relevant parameters and Control Change values. Allow

sufﬁcient time for processing to execute (about 50 msec)

before sending the YDP-113 another message.

• XG Native Parameter Change message may contain two or

four bytes of parameter data (depending on the parameter

size).

•For information about the Address and Byte Count values,

refer to Table 1 below. Note that the table’s Total Size value

gives the size of a bulk block. Only the top address of the

block (00H, 00H, 00H) is valid as a bulk data address.

8. SYSTEM EXCLUSIVE MESSAGES

(Digital Piano MIDI Format)

Data format:

[F0H] -> [43H] -> [73H] -> [xxH] -> [nnH] -> [F7H]

F0H = Exclusive status

43H = Yamaha ID

73H = Digital Piano ID

01H = Product ID (YDP common)

7F= Extended Product ID

xxH = Product ID (YDP-113: 24H)

nnH = Substatus

nn Control

02H Internal MIDI clock

03H External MIDI clock

06H Bulk Data (the bulk data follows 06H)

F7H = End of Exclusive

* When nn=02H or 03H, YDP common ID (01H) is rec-

ognized as well as 75H.

SYSTEM EXCLUSIVE MESSAGES (Special Control)

Data format: [F0H] -> [43H] -> [73H] -> [66H] -> [11H] ->

[0nH] -> [ccH] -> [vvH] -> [F7H]

F0H = Exclusive status

43H = Yamaha ID

73H = Digital Piano ID

7FH = Extended Product ID

xxH = Product ID (YDP-113: 24H)

11H = Special control

0nH = Control MIDI change (n=channel number)

cc = Control number

vv = Value

F7H = End of Exclusive

Control Channel ccH vvH

Split Point Always 00H 14H

14H : Split Key Numbe

Metronome Always 00H 1BH 00H : off

01H : –

02H : 2/4

03H : 3/4

04H : 4/4

05H : 5/4

06H : 6/4

7FH : No accent

Damper Level

ch: 00H-0FH 3DH(Sets the Damper Level

for each channel)

00H-7FH

Channel Detune

ch: 00H-0FH 43H (Sets the Detune value

for each channel)

00H-7FH

Voice Reserve

ch: 00H-0FH 45H 00H : Reserve off

7FH : on*

When Volume, Expression is received for Reserve On, they

will be effective from the next Key On. Reserve Off is normal.

10.SYSTEM EXCLUSIVE MESSAGES (Others)

Data format:

[F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H]

-> [00H] -> [mmH] -> [

H] -> [ccH] -> [F7H]

Master Tuning (XG and last message priority) simultaneously

changes the pitch of all channels.

F0H = Exclusive Status

43H = Yamaha ID

1nH = When received, n=0~F.

When transmitted, n=0.

27H = Model ID of TG100

30H = Sub ID

00H =

mmH =Master Tune MSB

llH = Master Tune LSB

ccH = don’t care (under 7FH)

F7H = End of Exclusive

YDP-113 Appendix/Anhang/Annexe/Apéndice

MIDI Parameter Change table (SYSTEM)

Address (H) Size (H) Data (H) Parameter Description Default value (H)

00 00 00 4 020C - 05F4(*1) MASTER TUNE -50 - +50[cent] 00 04 00 00

01 1st bit 3 - 0 ➝ bit 15 - 12 400

02 2nd bit 3 - 0 ➝ bit 11 - 8

03 3rd bit 3 - 0 ➝ bit 7 - 4

4th bit 3 - 0 ➝ bit 3 - 0

04 1 00 - 7F MASTER VOLUME 0 - 127 7F

05 1 — —

06 1 34 - 4C(*2) TRANSPOSE -12 - +12[semitones] 40

7E 00 XG SYSTEM ON 00=XG sytem ON

7F 00 RESET ALL PARAMETERS 00=ON (receive only)

TOTAL SIZE 07

*1: Values lower than 020CH select -50 cents. Values higher than 05F4H select +50 cents.

*2: Values from 28H through 33H are interpreted as -12 through -1. Values from 4DH through 58H are interpreted as +1 through +12.

MIDI Parameter Change table (EFFECT 1)

Refer to the “Effect MIDI Map” for a complete list of Reverb, Chorus and Variation type numbers.

Address (H) Size (H) Data (H) Parameter Description Default value (H)

02 01 00 2 00-7F REVERB TYPE MSB Refer to Effect MIDI Map 01(=HALL1)

00-7F REVERB TYPE LSB 00 : basic type 00

02 01 40 2 00-7F VARIATION TYPE MSB Refer to Effect MIDI Map 00(=Effect off)

00-7F VARIATION TYPE LSB 00 : basic type 00

• “VARIATION” refers to the EFFECT on the panel.

MIDI Parameter Change table (MULTI PART)

Address (H) Size (H) Data (H) Parameter Description Default value (H)

08 nn 11 1 00 - 7F DRY LEVEL 0 - 127 7F

nn = Part Number

• Effect MIDI Map

REVERB

MSB LSB

ROOM 02H 10H

HALL 1 01H 10H

HALL 2 01H 11H

STAGE 03H 10H

EFFECT

MSB LSB

CHORUS 42H 10H

PHASER 48H 10H

TREMOLO 46H 10H

DELAY 05H 10H

YDP-113 Appendix/Anhang/Annexe/Apéndice

MIDI Implementation Chart

YAMAHA [Digital Piano] Date: 27 May, 2002

Model: YDP-113 MIDI Implementation Chart Version: 1.0

Mode 1: OMNI ON, POLY Mode 2: OMNI ON, MONO O : Yes

Mode 3: OMNI OFF, POLY Mode 4: OMNI OFF, MONO X : No

Function Transmitted Recognized Remarks

Basic Default

Channel Changed

1 - 16

Default

Mode Messages

Altered

*****************

1 *1

Poly Mode only

Note

Number : True voice

9 - 120

*****************

0 - 127

Velocity Note ON

Note OFF

O 9nH, v=1 - 127

O 9nH, v=0

O 9nH, v=1 - 127

O 9nH, v=0 or 8nH

After Key’s

Touch Ch’s

Pitch Bender X X

Control Change 0, 32

Bank Select

Volume

Expression

Damper

Sostenuto

Soft pedal

Reverb Depth

Effect Depth

Program

Change : True #

*****************

System Exclusive O O

: Song Position

Common : Song Select

: Tune

System : Clock

Real Time : Commands

: All sounds off

Aux: Reset All Controllers

: Local ON/OFF

Messages : All Notes OFF

: Active Sense

: Reset

O (120, 126, 127)

O (121)

O (122)

O (123 - 125)

Notes : *1 = Recieve Mode is always multi timbre and Poly mode.

YDP-113

Appendix/Anhang/Annexe/Apéndice

Speciﬁcations / Technische Daten /

Caractéristiques techniques / Especiﬁcaciones

*Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change

or modify products or speciﬁcations at any time without prior notice. Since speciﬁcations, equipment or options may not be the

same in every locale, please check with your Yamaha dealer.

*Die technischen Daten und Beschreibungen in dieser Bedienungsanleitung dienen nur der Information. Yamaha Corp. behält sich

das Recht vor, Produkte oder deren technische Daten jederzeit ohne vorherige Ankündigung zu verändern oder zu modiﬁzieren. Da

die technischen Daten, das Gerät selbst oder Sonderzubehör nicht in jedem Land gleich sind, setzen Sie sich im Zweifel bitte mit

Ihrem Yamaha-Händler in Verbindung.

*Les caractéristiques techniques et les descriptions du mode d’emploi ne sont données que pour information. Yamaha Corp. se

réserve le droit de changer ou modiﬁer les produits et leurs caractéristiques techniques à tout moment sans aucun avis. Du fait que

les caractéristiques techniques, les équipements et les options peuvent différer d’un pays à l’autre, adressez-vous au distributeur

Yamaha le plus proche.

* Las especiﬁcaciones y descripciones de este manual del propietario tienen sólo el propósito de servir como información. Yamaha

Corp. se reserva el derecho a efectuar cambios o modiﬁcaciones en los productos o especiﬁcaciones en cualquier momento sin pre-

vio aviso. Puesto que las especiﬁcaciones, equipos u opciones pueden no ser las mismas en todos los mercados, solicite información

a su distribuidor Yamaha.

Keyboard 88 keys (A-1 - C7)

Sound Source AWM Stereo Sampling

Polyphony 32 Notes Max.

Voice Selection 10

Effect Room, Hall 1, Hall 2, Stage

Volume Master Volume

Controls Dual, Metoronome, Transpose

Pedal Damper

Demo Songs 10 voice Demo Songs, 50 preset Songs

Jacks/Connectors MIDI (IN/OUT/THRU), PHONES

2, DAMPER PEDAL

Main Ampliﬁers 20W

Speakers Oval (12cm

6cm)

Dimensions (W

(with music rest)

1345mm

426mm

815mm [52-15/16"

16-3/4"

32-1/16"]

(1345mm

426mm

968mm) [53-15/16"

16-3/4"

38-1/8"]

Weight 36kg (79lbs., 6oz)

Accessories

Owner’s Manual, “50 greats for the Piano” (Music Book), Bench (included or optional depend-

ing on locale), Quick Operation Guide, Damper pedal

YDP-113 Appendix/Anhang/Annexe/Apéndice

MEMO

IMPORTANT SAFETY INSTRUCTIONS

INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,

AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.

WARNING- When using any electrical or electronic product,

basic precautions should always be followed. These precautions

include, but are not limited to, the following:

1. Read all Safety Instructions, Installation Instructions, Spe-

cial Message Section items, and any Assembly Instructions

found in this manual BEFORE making any connections, includ-

ing connection to the main supply.

2. Main Power Supply Veriﬁcation: Yamaha products are

manufactured speciﬁcally for the supply voltage in the area

where they are to be sold. If you should move, or if any doubt

exists about the supply voltage in your area, please contact your

dealer for supply voltage veriﬁcation and (if applicable) instruc-

tions. The required supply voltage is printed on the name plate.

For name plate location, please refer to the graphic found in the

Special Message Section of this manual.

3. This product may be equipped with a polarized plug (one

blade wider than the other). If you are unable to insert the plug

into the outlet, turn the plug over and try again. If the problem

persists, contact an electrician to have the obsolete outlet

replaced. Do NOT defeat the safety purpose of the plug.

4. Some electronic products utilize external power supplies

or adapters. Do NOT connect this type of product to any power

supply or adapter other than one described in the owners manual,

on the name plate, or speciﬁcally recommended by Yamaha.

5. WARNING: Do not place this product or any other

objects on the power cord or place it in a position where anyone

could walk on, trip over, or roll anything over power or connect-

ing cords of any kind. The use of an extension cord is not recom-

mended! If you must use an extension cord, the minimum wire

size for a 25’ cord (or less) is 18 AWG. NOTE: The smaller the

AWG number, the larger the current handling capacity. For

longer extension cords, consult a local electrician.

6. Ventilation: Electronic products, unless speciﬁcally

designed for enclosed installations, should be placed in locations

that do not interfere with proper ventilation. If instructions for

enclosed installations are not provided, it must be assumed that

unobstructed ventilation is required.

7. Temperature considerations: Electronic products should

be installed in locations that do not signiﬁcantly contribute to

their operating temperature. Placement of this product close to

heat sources such as; radiators, heat registers and other devices

that produce heat should be avoided.

8. This product was NOT designed for use in wet/damp loca-

tions and should not be used near water or exposed to rain.

Examples of wet/damp locations are; near a swimming pool, spa,

tub, sink, or wet basement.

9. This product should be used only with the components

supplied or; a cart, rack, or stand that is recommended by the

manufacturer. If a cart, rack, or stand is used, please observe all

safety markings and instructions that accompany the accessory

product.

10. The power supply cord (plug) should be disconnected

from the outlet when electronic products are to be left unused for

extended periods of time. Cords should also be disconnected

when there is a high probability of lightning and/or electrical

storm activity.

11. Care should be taken that objects do not fall and liquids are

not spilled into the enclosure through any openings that may exist.

12. Electrical/electronic products should be serviced by a

qualiﬁed service person when:

a. The power supply cord has been damaged; or

b. Objects have fallen, been inserted, or liquids have been

spilled into the enclosure through openings; or

c. The product has been exposed to rain: or

d. The product dose not operate, exhibits a marked change

in performance; or

e. The product has been dropped, or the enclosure of the

product has been damaged.

13. Do not attempt to service this product beyond that

described in the user-maintenance instructions. All other servic-

ing should be referred to qualiﬁed service personnel.

14. This product, either alone or in combination with an

ampliﬁer and headphones or speaker/s, may be capable of pro-

ducing sound levels that could cause permanent hearing loss. DO

NOT operate for a long period of time at a high volume level or

at a level that is uncomfortable. If you experience any hearing

loss or ringing in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

15. Some Yamaha products may have benches and/or accessory

mounting ﬁxtures that are either supplied as a part of the product

or as optional accessories. Some of these items are designed to be

dealer assembled or installed. Please make sure that benches are

stable and any optional ﬁxtures (where applicable) are well

secured BEFORE using. Benches supplied by Yamaha are

designed for seating only. No other uses are recommended.

PLEASE KEEP THIS MANUAL

92-469-2

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

(2 wires)

• This applies only to products distributed by Yamaha-Kemble Music

(U.K.) Ltd.

(polarity)

• This applies only to products distributed by Yamaha Canada Music

Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada

Musique Ltée.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instruc-

tions contained in this manual, meets FCC require-

ments. Modiﬁcations not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2. IMPORTANT: When connecting this product to acces-

sories and/or another product use only high quality

shielded cables. Cable/s supplied with this product

MUST be used. Follow all installation instructions. Fail-

ure to follow instructions could void your FCC authoriza-

tion to use this product in the USA.

3. NOTE: This product has been tested and found to com-

ply with the requirements listed in FCC Regulations,

Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices. This equipment generates/

uses radio frequencies and, if not installed and used

according to the instructions found in the users manual,

may cause interference harmful to the operation of

other electronic devices. Compliance with FCC regula-

tions does not guarantee that interference will not occur

in all installations. If this product is found to be the

source of interference, which can be determined by

turning the unit “OFF” and “ON”, please try to eliminate

the problem by using one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfac-

tory results, please contact the local retailer authorized

to distribute this type of product. If you can not locate

the appropriate retailer, please contact Yamaha Corpo-

ration of America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this appa-

ratus may not correspond with the coloured makings iden-

tifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to

the terminal which is marked with the letter L or coloured

RED.

Making sure that neither core is connected to the earth ter-

minal of the three pin plug.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA

PRISE ET POUSSER JUSQU’AU FOND.

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou

au distributeur le plus proche de vous ﬁgurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de Mexico S.A. De C.V.,

Departamento de ventas

Javier Rojo Gomez No.1149, Col. Gpe Del

Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.

Tel: 686-00-33

BRAZIL

Yamaha Musical do Brasil LTDA.

Av. Rebouças 2636, São Paulo, Brasil

Tel: 011-853-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Viamonte 1145 Piso2-B 1053,

Buenos Aires, Argentina

Tel: 1-4371-7021

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

IRELAND

Danfay Ltd.

61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin

Tel: 01-2859177

GERMANY

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Central Europe GmbH,

Branch Switzerland

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Central Europe GmbH,

Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

THE NETHERLANDS

Yamaha Music Central Europe,

Branch Nederland

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

BELGIUM/LUXEMBOURG

Yamaha Music Central Europe GmbH,

Branch Belgium

Rue de Geneve (Genevastraat) 10, 1140 - Brussels,

Belgium

Tel: 02-726 6032

FRANCE

Yamaha Musique France, S.A.

Division Professionnelle

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha-Hazen Música, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

GREECE

Philippos Nakas S.A. The Music House

147 Skiathou Street, 112-55 Athens, Greece

Tel: 01-228 2160

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1

Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 8B

DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

F-Musiikki Oy

Kluuvikatu 6, P.O. Box 260,

SF-00101 Helsinki, Finland

Tel: 09 618511

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1

N-1345 Østerås, Norway

Tel: 67 16 77 70

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120

IS-128 Reykjavik, Iceland

Tel: 525 5000

OTHER EUROPEAN COUNTRIES

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2312

TURKEY/CYPRUS

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LB21-128 Jebel Ali Freezone

P.O.Box 17328, Dubai, U.A.E.

Tel: +971-4-881-5868

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 2737-7688

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong,

Youngdungpo-ku, Seoul, Korea

Tel: 02-3770-0661

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-703-0900

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music Asia Pte., Ltd.

11 Ubi Road #06-00, Meiban Industrial Building,

Singapore

Tel: 65-747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

121/60-61 RS Tower 17th Floor,

Ratchadaphisek RD., Dindaeng,

Bangkok 10320, Thailand

Tel: 02-641-2951

THE PEOPLE’S REPUBLIC OF CHINA

AND OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

NEW ZEALAND

Music Houses of N.Z. Ltd.

146/148 Captain Springs Road, Te Papapa,

Auckland, New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2312

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

HEAD OFFICE

Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-3273

[CL] 29

YDP113(E).book Page 45 Wednesday, April 30, 2003 10:25 AM