Yamaha SP2060 V1 de handleiding

Merk: Yamaha

Model: SP2060 V1

Categorie: Audio-equalizers

Type: de handleiding

Deze handleiding is ook geschikt voor

SP2060
V1

Owner’s Manual

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

Precautions for Using a Rack-mounted SP2060

If several SP2060 units (or an SP2060 unit together with other

devices) are installed in a poorly-ventilated rack, the heat generated

by each unit may raise the temperature inside the rack, preventing

the SP2060 from performing as designed. When mounting SP2060

units in a rack, please leave one rack space vacant for every two

units. You can attach a ventilation panel to this space or leave it

open to prevent excessive heat build-up.

If the temperature inside the rack is expected to rise above 40

degrees Celsius or 104 degrees Fahrenheit (or if the ambient

temperature outside the rack is expected to rise above 30 degrees

Celsius or 86 Fahrenheit), install a fan kit in the top row of the rack.

The fan must provide airﬂow of 1.6 m

/min or more and static

pressure of 5 mmH

O or more.

Vorsichtsmaßnahmen für den Einsatz eines im Rack montierten SP2060

Wenn in einem schlecht belüfteten Rack mehrere SP2060-

Einheiten (oder eine SP2060-Einheit zusammen mit anderen

Geräten) untergebracht sind, kann die von den Geräten erzeugte

Wärme die Temperatur im Rack erhöhen, was die vorgesehene

Leistung des SP2060 beeinträchtigt. Wenn Sie SP2060-Einheiten in

einem Rack einbauen, lassen Sie bitte alle zwei Geräte einen Rack-

Platz frei. Sie können an diesem Platz eine Lüftungsverkleidung

anbringen oder ihn offen lassen, um die Entwicklung übermäßiger

Hitze zu verhindern.

Wenn zu erwarten ist, dass die Temperatur im Rack über 40 Grad

Celsius oder 104 Grad Fahrenheit ansteigt (oder wenn die

Umgebungstemperatur außerhalb des Racks über 30 Grad Celsius

oder 86 Grad Fahrenheit ansteigt), installieren Sie eine

Lüftereinheit im Rack. Der Lüfter muss einen Luftdurchsatz von

mindestens 1,6 m

/Minute oder mehr haben und einen statischen

Druck von 5 mmH

O erzeugen können.

Précautions à prendre en cas d’utilisation d’un SP2060 monté en rack

Si vous installez plusieurs SP2060 (ou un SP2060 et d’autres

périphériques) dans un rack mal aéré, la chaleur générée par

chaque unité risque d’augmenter la température à l’intérieur du

rack et d’empêcher le SP2060 de fonctionner correctement.

Lorsque vous montez des SP2060 en rack, laissez un espace libre

équivalant à un rack entre deux unités. Vous pouvez recouvrir cet

espace d’un panneau de ventilation ou le laisser ouvert pour éviter

toute accumulation de chaleur excessive.

Si vous craignez que la température à l’intérieur du rack ne dépasse

40 degrés Celsius ou 104 degrés Fahrenheit (ou que la température

ambiante à l’extérieur du rack ne dépasse 30 degrés Celsius ou 86

degrés Fahrenheit), installez un kit de ventilation sur la rangée

supérieure du rack. Le ventilateur doit fournir un ﬂux d’air de

1,6 m

/min ou plus et une pression statique de 5 mmH

O ou plus.

Precauciones para utilizar una SP2060 de montaje en bastidor

Si se instalan varias unidades SP2060 (o una unidad SP2060 con

otros dispositivos) en un bastidor insuﬁcientemente ventilado, el

calor generado por cada unidad podría aumentar la temperatura en

el interior del bastidor, impidiendo que la unidad SP2060 funcione

de la manera prevista. Cuando monte unidades SP2060 en un

bastidor, deje un espacio de bastidor libre por cada dos unidades.

Puede instalar un panel de ventilación en este espacio, o bien

dejarlo abierto para evitar la acumulación de un calor excesivo.

Si se espera que la temperatura interior del bastidor supere los 40

grados Celsius (o que la temperatura ambiente fuera del bastidor

supere los 30 grados Celsius), instale un kit de ventilación en la ﬁla

superior del bastidor. El ventilador debe proporcionar una

corriente de aire de 1,6 m

/min o más y una presión de 5 mmH

o más.

Fan kit

Ventilation panel

SP2060

The above warning is located on the top of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table speciﬁed

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

(98-6500)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate)

This product contains a battery that contains perchlorate material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif.

90620

Telephone : 714-522-9011

Type of Equipment : SPEAKER PROCESSOR

Model Name : SP2060

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including inter-

ference that may cause undesired operation.

See user manual instructions if interference to radio reception is

suspected.

(FCC DoC)

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskift-

ning må kun ske med batteri af samme fabrikat og type. Levér det

brugte batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp

eller en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda

paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä

käytetty paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-up.

• This apparatus contains a lithium battery for memory back-up.

• Raadpleeg uw leverancier over de verwijdering van de batterij op

het moment dat u het apparaat ann het einde van de levensduur

afdankt of de volgende Yamaha Service Afdeiing:

Yamaha Music Nederland Service Afdeiing

Kanaalweg 18-G, 3526 KL UTRECHT

Tel. 030-2828425

•For the removal of the battery at the moment of the disposal at the

end of the service life please consult your retailer or Yamaha Ser-

vice Center as follows:

Yamaha Music Nederland Service Center

Address : Kanaalweg 18-G, 3526 KL UTRECHT

Tel: 030-2828425

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small chemi-

cal waste.

(lithium disposal)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING:

THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accor-

dance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals

in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be con-

nected to the terminal in the plug which is marked by the letter E or

by the safety earth symbol or colored GREEN or GREEN-and-

YELLOW.

The wire which is coloured BLUE must be connected to the termi-

nal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the ter-

minal which is marked with the letter L or coloured RED.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.(3 wires)

(5)-4

4/2

SP2060 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the device. The required voltage is

printed on the name plate of the device.

• Use only the included power cord.

If you intend to use the device in an area other than in the one you purchased,

the included power cord may not be compatible. Please check with your Yamaha

dealer.

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• Do not open the device or attempt to disassemble the internal parts or modify

them in any way. The device contains no user-serviceable parts. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected

by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions,

or place containers on it containing liquids which might spill into any openings.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the device, or if any unusual smells or smoke

should appear to be caused by it, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the device inspected by

qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used for

extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

• When setting up the product, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn off

the power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still ﬂowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

•Avoid setting all equalizer controls and faders to their maximum. Depending on

the condition of the connected devices, doing so may cause feedback and may

damage the speakers.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat

(such as in direct sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall

over.

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Doing so may result in noise, both in the device

itself and in the TV or radio next to it.

• Before connecting the device to other devices, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to

minimum.

• Be sure to connect to a properly grounded power source. A ground screw is

provided on the rear panel of this device for maximum safety and shock

prevention. If the mains outlet is not grounded, be sure to connect the ground

screw to a conﬁrmed ground point before plugging the device into the mains.

Improper grounding can result in electrical shock.

• Remove the power plug from the AC outlet when cleaning the device.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

Connections

Maintenance

(5)-4

5/2

SP2060 Owner’s Manual

• Do not use the device for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

• This device has a built-in backup battery. When you unplug the power cord from

the AC outlet, the current scene data is retained. However, the life of the backup

battery is about ﬁve years. If the battery wears out, the current scene data will be

lost. When the backup battery charge becomes low, the unit ﬁrst displays “LOW

BATTERY” then “CRITICAL BATTERY” when you turn on the power to the unit.

(The Battery page of the Utility display also indicates ﬁrst “Low Battery” then

“No Battery” when the charge becomes low.) In this case, please have qualiﬁed

Yamaha service personnel replace the backup battery.

The rubber feet included in this package can be attached to the bottom of this device to prevent slippage when it is to be used on a slippery surface.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

Handling caution Backup battery

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

• The illustrations in this document are for instructional purposes, and may appear somewhat different from the actual equipment.

• CobraNet is a trademark of Cirrus Logic, Inc.

• Ethernet is a trademark of Xerox Corporation.

• All other trademarks are the property of their respective holders and are hereby acknowledged.

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

Foreword .......................................... 7

Accessories (Please make sure the following items are

included in the package.)................................................. 7

About the Firmware Version ........................................... 7

About DME Designer..................................................... 7

Precautions for Using a Rack-mounted SP2060 .............. 7

Preparation...................................................................... 7

Connecting the AC power cord........................................... 7

Turning the power on and off ............................................. 7

Introduction to the SP2060 ..................... 8

Features........................................................................... 8

Glossary for the SP2060.................................................. 8

Configuration ................................................................. 9

3 x 2-way ............................................................................ 9

3 x 2-way Link .................................................................... 9

2 x (2-way + Sub).............................................................. 10

2 x (2-way + Sub) Link...................................................... 10

2 x 2-way + 2 x Aux .......................................................... 11

2 x 2-way + 2 x Aux Link .................................................. 11

2 x 3-way .......................................................................... 12

2 x 3-way Link .................................................................. 12

4 way +2 x Aux ................................................................. 13

5-way + Aux...................................................................... 14

6-way ................................................................................ 15

Multi Zone ....................................................................... 16

System Examples........................................................... 17

Speaker processing ............................................................ 17

Zone processing ................................................................ 18

Multiple SP2060............................................................... 19

The Controls and Connectors.................. 21

Front Panel ................................................................... 21

Rear Panel..................................................................... 22

Panel Operation ................................. 23

Basic Operation............................................................. 23

Changing the parameter values.......................................... 23

LEVEL.......................................................................... 23

DELAY ......................................................................... 24

EQ (Equalizer) .............................................................. 24

Input EQ .......................................................................... 24

Output EQ ....................................................................... 25

ROUTING................................................................... 26

Input routing .................................................................... 26

Output routing ................................................................. 26

X-OVER (Crossover) .................................................... 27

Setting the Crossover ........................................................ 27

LIBRARY...................................................................... 28

Displaying the current library............................................ 28

Recalling a library.............................................................. 28

LIMITER...................................................................... 29

SCENE ......................................................................... 29

About a scene..................................................................... 29

Recalling a scene ................................................................ 30

Storing a scene ................................................................... 31

Changing a scene title ........................................................ 31

Protecting a scene .............................................................. 31

Deleting a scene ................................................................. 32

UTILITY ...................................................................... 32

INPUT A/B LINK ............................................................ 32

User Lock .......................................................................... 33

Setting the Last Memory Resume ...................................... 33

Displaying the label ........................................................... 34

Displaying word clock ....................................................... 34

Checking the backup battery.............................................. 35

Displaying the firmware version......................................... 35

Initializing the SP2060 ...................................................... 35

Mute ............................................................................. 36

Network Settings ................................ 37

Setting a Device Group ................................................. 37

Setting the IP Address ................................................... 37

Setting the Master ID.................................................... 38

Setting Link Mode ........................................................ 38

Viewing the MAC Address ............................................ 39

References ....................................... 40

About Preset Libraries ................................................... 40

File name ........................................................................... 40

Subwoofer.......................................................................... 40

Limiter............................................................................... 40

Libraries for 1-way speaker processors ................................ 41

Libraries for 2-way speaker processors ................................ 42

Libraries for 3-way speaker processors ................................ 43

Display Messages........................................................... 44

Warning and error messages............................................... 44

Status messages .................................................................. 45

Troubleshooting............................................................ 45

General Specifications ................................................... 46

Electrical Characteristics................................................ 46

Input/Output Characteristics ........................................ 47

Connector Pin Assignment............................................ 48

Dimensions ................................................................... 49

Index ............................................................................. 50

Contents

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

SP2060 Owner’s Manual

Thank you for purchasing the Yamaha SP2060 Speaker Processor.

In order to take full advantage of the features and performance provided by the SP2060, we urge you to read this owner’s manual

thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference.

Accessories (Please make

sure the following items are

included in the package.)

• SP2060 Owner’s Manual (this document)

•AC power cord

•Rubber feet x 4

About the Firmware Version

You can check the firmware version of your SP2060 in the

UTILITY display (see page 28).

You can also download the latest firmware from the follow-

ing Yamaha website.

http://www.yamahaproaudio.com/

About DME Designer

DME Designer software enables you to control the SP2060

or DME series system from a connected computer.

The DME Designer version 2.0 or later features this func-

tion.

You can download DME Designer from the following

Yamaha website.

http://www.yamahaproaudio.com/

Precautions for Using a

Rack-mounted SP2060

If you install the SP2060 along with other SP2060 units or

other devices in a poorly ventilated rack, the ambient tem-

perature inside the rack may rise, resulting in inefficient per-

formance. Be sure to install the SP2060 in a well-ventilated

rack and make sure that the heat will be ventilated efficiently.

If the temperature inside the rack is expected to rise above 40

degrees Celsius or 104 degrees Fahrenheit (or if the ambient

temperature outside the rack is expected to rise above 30 de-

grees Celsius or 86 Fahrenheit), install a fan kit in the top

row of the rack. The fan must provide airflow of 1.6m

/min

or more and static pressure of 5mmH

O or more.

Preparation

Connecting the AC power cord

First plug the female-connector end of the AC cord into the

[AC IN] socket on the rear panel of the SP2060, then plug

the male plug into an appropriate AC mains outlet. Be sure

to use the voltage specified for the device. The required volt-

age is printed on the name plate of the device.

Turning the power on and off

Press the [POWER] switch to turn the power

on to the SP2060.

The SP2060 displays a message.

Press the [POWER] switch again to turn off

the power.

Foreword

Fan kit

SP2060

Be sure to turn all devices OFF before connecting AC

mains power.

To prevent the initial power-on surge from generating a

large noise spike or damaging your speaker system, turn

devices on in the following order: audio sources, mixer

(such as M7CL), SP2060, and ﬁnally power ampliﬁers.

Reverse this order when turning power off.

NOTE

The SP2060 remembers the scene settings when you turn off the

power. When you turn on the power to the SP2060, it will start

up with the same scene settings.

You can also set up the SP2060 so that at the startup it will recall

the scene selected before you turned off the power to the device

(See page 33).

Do NOT turn off the power to the SP2060 while the unit

is displaying the message “DO NOT TURN OFF!” at the

bottom of the display, for example, while it is storing the

scene.

Otherwise, a malfunction may occur.

CAUTION

SpeakerProcessor

SP2060

CAUTION

SP2060 Owner’s Manual

Foreword

Introduction

to the SP2060

Network Settings ReferencesPanel Operation

The Controls

and Connectors

Features

The Yamaha SP2060 Speaker Processor employs state-of-the-art digital technology and supports 96kHz audio.

The SP2060 features two channel analog input connectors, an AES/EBU connector, and six channel analog out-

put connectors.

Since it includes preset settings for fixed installation speakers (such as the Yamaha IF/IS series), the SP2060 enables

you to take the best advantage of a variety of speakers from 1-way through 6-way speakers. You can also control

the SP2060 remotely using DME Designer application software.

Glossary for the SP2060

This section explains terminology specific to the SP2060.

Components & Parameters

The individual audio modules (equalizers, delays, and speaker processors that feature various speaker adjustment

functions) are called “components.” Various settings included with each component are called “preset parame-

ters.” Changing the parameter values for components enables you to control the effects of the audio process.

Conﬁguration

A “configuration” is a complete set of components for constructing an optimum audio system that supports the

connected speakers. See page 9.

Each configuration determines the audio function(s) of the corresponding SP2060 unit. All parameter sets includ-

ed with each component in a configuration are called “preset parameters.”

Scene

A combination of all configuration and preset parameter combinations is called a “scene.” A scene can be recalled

from the panel of each SP2060 or via DME Designer. See page 29.

Library

All parameter sets included with each speaker processor component optimized for the connected speakers are

called “libraries.” A library can be recalled from the panel of each SP2060 or via DME Designer. You can also

create a library using DME Designer, then store it in an SP2060.

Introduction to the SP2060

Scene

Scene 1

Scene 2

Scene 99

Component

Configuration

Preset

Parameter

Example: Limiter

• Attack

• Threshold

• Release

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Introduction to the SP2060

SP2060 Owner’s Manual

Configuration

The SP2060 features 12 configurations. You can select one that suits the combination and configuration of the

connected speakers.

A configuration is stored as part of each preset scene (read-only scene) in scene memory slots #1 through #12, and

can be recalled along with the corresponding scene. You can also edit parameters of a configuration, then store

them in a user scene (readable and writable scene). Connection between the output port and output connector on

each component is specified and fixed for each configuration.

3 x 2-way

Controls three channel 2-way speakers.

3 x 2-way Link

Controls three channel 2-way speakers. All parameters for each component such as the Crossover, Delay, EQ, Lev-

el, and Limiter (excluding the Mute parameter) are linked.

No.1. [3x2way ] No.5. [2x2way+2xAux ] No.9. [4way+2xAux ]

No.2. [3x2way L ] No.6. [2x2way+2xAuxL ] No.10. [5way+Aux ]

No.3. [2x(2way+Sub) ] No.7. [2x3way ] No.11. [6way ]

No.4. [2x(2way+Sub)L ] No.8. [2x3way L ] No.12. [Multi Zone ]

Output connector

Speaker’s input connector

OUTPUT 1 2-way speaker (1) LOW

OUTPUT 2 2-way speaker (1) HIGH

OUTPUT 3 2-way speaker (2) LOW

OUTPUT 4 2-way speaker (2) HIGH

OUTPUT 5 2-way speaker (3) LOW

OUTPUT 6 2-way speaker (3) HIGH

[INPUT B]

[INPUT A]

[DIGITAL IN]

Input

Level

Input

Level

Input

Mute

Input

8BandEQ

Input

8BandEQ

Input

Delay

Input

Delay

Input

Mute

BA SUM

Input

8BandEQ

Input

Delay

[Library Data]

[OUTPUT 2]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 6]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 4]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 1]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

[OUTPUT 5]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

[OUTPUT 3]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

Introduction to the SP2060

SP2060 Owner’s Manual

Foreword

Introduction

to the SP2060

Network Settings ReferencesPanel Operation

The Controls

and Connectors

2 x (2-way + Sub)

Controls two channel 2-way speakers and subwoofers.

2 x (2-way + Sub) Link

Controls two channel 2-way speakers and subwoofers. All parameters for each component such as the Crossover,

Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked.

Output connector Speaker’s input connector

OUTPUT 1 Subwoofer (1)

OUTPUT 2 2-way speaker (1) LOW

OUTPUT 3 2-way speaker (1) HIGH

OUTPUT 4 Subwoofer (2)

OUTPUT 5 2-way speaker (2) LOW

OUTPUT 6 2-way speaker (2) HIGH

[INPUT B]

[INPUT A]

[DIGITAL IN]

Input

Level

Input

Level

Input

Mute

Input

8BandEQ

Input

8BandEQ

Input

Delay

Input

Delay

Input

Mute

Input

8BandEQ

Input

Delay

BA SUM

[OUTPUT 1]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

SUB WOOFER

[OUTPUT 6]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 5]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

[OUTPUT 4]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

SUB WOOFER

[OUTPUT 3]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 2]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

[Library Data]

LOW

HIGH

LOW

HIGH

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Introduction to the SP2060

SP2060 Owner’s Manual

2 x 2-way + 2 x Aux

Controls two channel 2-way speakers and two channel subspeakers.

2 x 2-way + 2 x Aux Link

Controls two channel 2-way speakers and two channel subspeakers. All parameters for each component such as

the Crossover, Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked.

Output connector Speaker’s input connector

OUTPUT 1 2-way speaker (1) LOW

OUTPUT 2 2-way speaker (1) HIGH

OUTPUT 3 2-way speaker (2) LOW

OUTPUT 4 2-way speaker (2) HIGH

OUTPUT 5 1-way subspeaker (1)

OUTPUT 6 1-way subspeaker (2)

[INPUT B]

[INPUT A]

[DIGITAL IN]

Input

Level

Input

Level

Input

Mute

Input

8BandEQ

Input

8BandEQ

Input

Delay

Input

Delay

Input

Mute

Input

8BandEQ

Input

Delay

BA SUM

[OUTPUT 6]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

SUB SPEAKER

[OUTPUT 5]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

SUB SPEAKER

[OUTPUT 4]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 3]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

[OUTPUT 2]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[Library Data]

HIGH

LOW

[OUTPUT 1]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

Introduction to the SP2060

SP2060 Owner’s Manual

Foreword

Introduction

to the SP2060

Network Settings ReferencesPanel Operation

The Controls

and Connectors

2 x 3-way

Controls two channel 3-way speakers.

2 x 3-way Link

Controls two channel 3-way speakers. All parameters for each component such as the Crossover, Delay, EQ, Level,

and Limiter (excluding the Mute parameter) are linked.

Output connector Speaker’s input connector

OUTPUT 1 3-way speaker (1) LOW

OUTPUT 2 3-way speaker (1) MID

OUTPUT 3 3-way speaker (1) HIGH

OUTPUT 4 3-way speaker (2) LOW

OUTPUT 5 3-way speaker (2) MID

OUTPUT 6 3-way speaker (2) HIGH

[INPUT B]

[INPUT A]

[DIGITAL IN]

Input

Level

Input

Level

Input

Mute

Input

8BandEQ

Input

8BandEQ

Input

Delay

Input

Delay

Input

Mute

Input

8BandEQ

Input

Delay

BA SUM

[OUTPUT 6]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 5]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

MID

[OUTPUT 3]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 2]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

MID

[Library Data]

MID

HIGH

LOW

MID

HIGH

[OUTPUT 1]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

[OUTPUT 4]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Introduction to the SP2060

SP2060 Owner’s Manual

4 way +2 x Aux

Controls one channel 4-way speaker and two channel subspeakers.

Output connector Speaker’s input connector

OUTPUT 1 4-way speaker (1) LOW

OUTPUT 2 4-way speaker (1) LOW-MID

OUTPUT 3 4-way speaker (1) HIGH-MID

OUTPUT 4 4-way speaker (1) HIGH

OUTPUT 5 1-way subspeaker (1)

OUTPUT 6 1-way subspeaker (2)

[INPUT B]

[INPUT A]

[DIGITAL IN]

Input

Level

Input

Level

Input

Mute

Input

8BandEQ

Input

8BandEQ

Input

Delay

Input

Delay

Input

Mute

Input

8BandEQ

Input

Delay

BA SUM

[OUTPUT 6]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

SUB SPEAKER

[OUTPUT 5]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

SUB SPEAKER

[OUTPUT 4]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 3]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH-MID

[OUTPUT 2]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW-MID

[Library Data]

LOW-MID

HIGH

LOW

HIGH-MID

[OUTPUT 1]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

Introduction to the SP2060

SP2060 Owner’s Manual

Foreword

Introduction

to the SP2060

Network Settings ReferencesPanel Operation

The Controls

and Connectors

5-way + Aux

Controls one channel 5-way speaker and one channel subspeaker.

Output connector Speaker’s input connector

OUTPUT 1 5-way speaker (1) SUB-LOW

OUTPUT 2 5-way speaker (1) LOW

OUTPUT 3 5-way speaker (1) LOW-MID

OUTPUT 4 5-way speaker (1) HIGH-MID

OUTPUT 5 5-way speaker (1) HIGH

OUTPUT 6 1-way subspeaker (1)

[INPUT B]

[INPUT A]

[DIGITAL IN]

Input

Level

Input

Level

Input

Mute

Input

8BandEQ

Input

8BandEQ

Input

Delay

Input

Delay

Input

Mute

Input

8BandEQ

Input

Delay

BA SUM

[OUTPUT 6]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

SUB SPEAKER

[OUTPUT 5]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 4]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH-MID

[OUTPUT 3]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW-MID

[OUTPUT 2]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

[Library Data]

LOW

HIGH

HIGH-MID

SUB-LOW

HIGH

LOW-MID

[OUTPUT 1]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

SUB-LOW

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Introduction to the SP2060

SP2060 Owner’s Manual

6-way

Controls one channel 6-way speaker.

Output connector Speaker’s input connector

OUTPUT 1 6-way speaker (1) SUB-LOW

OUTPUT 2 6-way speaker (1) LOW

OUTPUT 3 6-way speaker (1) LOW-MID

OUTPUT 4 6-way speaker (1) MID

OUTPUT 5 6-way speaker (1) HIGH-MID

OUTPUT 6 6-way speaker (1) HIGH

[INPUT B]

[INPUT A]

[DIGITAL IN]

Input

Level

Input

Level

Input

Mute

Input

8BandEQ

Input

8BandEQ

Input

Delay

Input

Delay

Input

Mute

Input

8BandEQ

Input

Delay

BA SUM

[OUTPUT 6]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 5]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH-MID

[OUTPUT 4]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

MID

[OUTPUT 3]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW-MID

[OUTPUT 2]

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

LOW

[Library Data]

LOW

HIGH

MID

SUB-LOW

HIGH-MID

LOW-MID

[OUTPUT 1]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

SUB-LOW

Introduction to the SP2060

SP2060 Owner’s Manual

Foreword

Introduction

to the SP2060

Network Settings ReferencesPanel Operation

The Controls

and Connectors

Multi Zone

Outputs only the frequency components (by retrieving them from the input signals) that are suitable for the re-

sponse characteristics of each speaker connected to each of six output connectors.

Output connector Speaker’s input connector

OUTPUT 1 1-way speaker (1)

OUTPUT 2 1-way speaker (2)

OUTPUT 3 1-way speaker (3)

OUTPUT 4 1-way speaker (4)

OUTPUT 5 1-way speaker (5)

OUTPUT 6 1-way speaker (6)

[INPUT B]

[INPUT A]

[DIGITAL IN]

Input

Level

Input

Level

Input

Mute

Input

8BandEQ

Input

8BandEQ

Input

Delay

Input

Delay

Input

Mute

Input

8BandEQ

Input

Delay

BA SUM

[OUTPUT 1]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 6]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 5]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 4]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 3]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[OUTPUT 2]

X-Over

Output

Delay

Output

6BandEQ

with APF

Output

Level

Output

Mute

LIMIT

Limiter

HIGH

[Library Data]

HIGH

LOW

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Introduction to the SP2060

SP2060 Owner’s Manual

System Examples

Speaker processing

This diagram indicates an example of a stereo 3-way system.

The AES/EBU input connector on the SP2060 enables you to connect it directly to the AES/EBU output on a

digital mixer.

The configuration presets include 3 x 2-way, 2 x 3-way, 4-way + 2 x Aux, 5-way + Aux, and 6-way. (See page 9.)

The SP2060 Routing function enables you to select IN A, IN B, or IN SUM (A+B) as component input. In this

way, you can create a stereo, mono, or stereo mono (full-range stereo plus mono subwoofer) system very easily.

You can also adjust the parameters or recall a scene from the front panel of the SP2060 or from a computer con-

nected via Ethernet.

Routing

Left/Right (AES/EBU)

* also Analog input available

M7CL

1234 56

XP7000 XP7000 XP7000 XP7000

Subwoofer Bi-amp 2way Subwoofer Bi-amp 2way

Main speaker L Main speaker R

Ethernet

AES/EBU

SP2060

IN A

IN A+B

IN B

OUT 1

OUT 2

OUT 3

OUT 4

OUT 5

OUT 6

Sub L

Low L

Hi L

Sub R

Low R

Hi R

Introduction to the SP2060

SP2060 Owner’s Manual

Foreword

Introduction

to the SP2060

Network Settings ReferencesPanel Operation

The Controls

and Connectors

Zone processing

This example is a stereo 3-zone system in which the SP2060 is used as a signal distributor, rather than a crossover.

Adjusting the routing will enable you to create a monaural 6-zone system. You can adjust EQ, Delay, and Level

for each output.

This system is suitable for a facility that requires sound zoning, such as stores, restaurants, hotels, conference fa-

cilities, and exhibition halls, or for delay speakers in an SR system.

Routing

12 3 4 65

XP7000 XP7000

LR LR LR

ZONE A ZONE B ZONE C

MG16/4

SP2060

XP7000

IN A

IN A+B

IN B

OUT 1

OUT 2

OUT 3

OUT 4

OUT 5

OUT 6

ZONE 1L

ZONE 1R

ZONE 2L

ZONE 2R

ZONE 3L

ZONE 3R

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Introduction to the SP2060

SP2060 Owner’s Manual

Multiple SP2060

This example is a system that uses CobraNet™ for long-distance digital transfer between the control room and

amp room.

Audio signals from Yamaha PM5D digital mixing console, talkback mic signal, chime source, etc. are input to the

DME64N. The output destination and level settings are specified via the Routing function.

Furthermore, you can process output signals (EQ, Limiter, etc.) by adding an EQ component. The output from

the DME64N is converted to CobraNet™ signals via the MY16-C, then transferred via the Ethernet cable to the

NHB32-C located in the amp room.

In the amp room, this signal is converted to the AES/EBU digital signal via the NHB32-C, then input to the

SP2060, which, in turn, processes the signal using the Crossover, EQ, Delay, and Limiter to suit each speaker.

The SP2060 control signal is also transferred to the amp room via the Ethernet cable. (Yamaha recommends that

you use Giga-bit switching hubs.)

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

NETWORK HUB AND BRIDGE

LINK CONDUCT

LOCK

ERROR

Control Room

PM5D

Cascade

Talkback mic

MY16-C

Specifying the

destination and

processing (such

as EQ) for the

output signal

Amp Room

NHB32-C

XP7000 XP7000 XP7000

12 34 56 1234 56

Ethernet

AES/EBU

CobraNet

Main L Main R

Mono Sub Stair Step

Under Balcony Lobby/

Dressing Room

Switching Hub

XM4180 XH200

SP2060 SP2060

DME64N

Switching Hub

Switching Hub Switching Hub

Introduction to the SP2060

SP2060 Owner’s Manual

Foreword

Introduction

to the SP2060

Network Settings ReferencesPanel Operation

The Controls

and Connectors

Routing

IN A

IN A+B

IN B

OUT 1

OUT 2

OUT 3

OUT 4

OUT 5

OUT 6

Low L

Hi L

Low R

Hi R

Mono Sub

Stair Step (Mono)

Under

Balcony

Lobby/

Dressing Room

IN A

IN A+B

IN B

OUT 1

OUT 2

OUT 3

OUT 4

OUT 5

OUT 6

Under Balcony 1

Under Balcony 2

Under Balcony 3

Under Balcony 4

Lobby

Dressing Room

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

SP2060 Owner’s Manual

Front Panel

1 Display

Displays the parameters selected for editing and information

about the currently-recalled scene.

Remove the transparent protective film that was applied pri-

or to shipment from the factory.

2 [BACK/STORE] Key

Selects the previous parameter. In the Scene display, it stores

a selected scene.

3 [▲INC/YES]/[▼DEC/NO] Keys

Confirm Yes or No to the change of parameter values or con-

firmation messages.

4 [NEXT/RECALL] Key

Selects the next parameter. In the Library List display or

Scene display, it recalls a selected library or scene respective-

ly.

5 [LEVEL] Key

Displays the input/output level settings. When these settings

are displayed, the key LED lights up.

6 [DELAY] Key

Displays the signal delay time settings. When these settings

are displayed, the key LED lights up.

7 [EQ] Key

Displays the EQ settings. When these settings are displayed,

the key LED lights up.

8 [ROUTING] Key

Displays the selection of the [INPUT] connectors and Out-

put channel signal sources. When these settings are dis-

played, the key LED lights up.

9 [X-OVER] Key

Displays the Crossover settings or library recall options.

When these settings are displayed, the key LED lights up.

) [LIMITER] Key

Displays the Limiter settings. When these settings are dis-

played, the key LED lights up.

! [SCENE] Key

Displays scene store or recall options, or scene edit options.

When these settings are displayed, the key LED lights up.

@ [UTILITY] Key

Displays the SP2060 Utility function settings. When these

settings are displayed, the key LED lights up.

# [MUTE] Key

Displays the Mute settings. When these settings are dis-

played, the key LED lights up. At this time, each [SEL] key

LED indicates the corresponding channel’s Mute On or Off

and the [SEL] keys enable you to turn Mute On or Off for

the corresponding channels.

Holding down the [MUTE] key for two seconds or longer

will turn the User Lock function On or Off.

$ [SEL] Keys

Select the corresponding channels for editing. The [SEL] key

LED for each selected channel lights up.

% Meters

Display the channel level meters and the Limiter indicators

for Output channels.

^ [POWER ON/OFF] Key

Turns mains power to the SP2060 on and off.

The Controls and Connectors

STOR E RECALL

YES

654321BA

1 2 4 5 6 7

! @ # $89)

3 % ^

The Controls and Connectors

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

Rear Panel

& Ground Screw

For maximum safety be sure to securely connect the SP2060

ground screw to an earth connection.

The supplied power cable has a three-prong plug that will

ground the unit when plugged into an appropriately ground-

ed three-prong type AC mains outlet. If the AC outlet is not

grounded, be sure to ground the unit by using this ground

screw.

Correct grounding will effectively eliminate hum noise and

interference.

* [AC IN] Connector

Connect to the AC mains using the supplied AC power cord.

First connect the power cord to the SP2060, then insert the

power cord plug into an AC outlet.

( [NETWORK] Connector

This is a 100Base-TX/10Base-T Ethernet connector for con-

nection to a computer or other device in the network.

º [DIGITAL INPUT] Connector (AES/EBU)

Connect an output of an AES/EBU (digital signal) compat-

ible device to this XLR-3-31 connector.

¡ [OUTPUT] Connectors

These XLR-3-32 balanced connectors output six channel an-

alog audio signals. Connect them to the inputs on amplifiers.

™ [INPUT] Connectors

These XLR-3-31 balanced connectors input two channel an-

alog audio signals.

123456

OUTPUT

DIGITAL

INPUT

AES/EBU

( º ¡ ™

& *

NOTE

•Use a CAT5 STP (Shielded Twisted Pair) cable for this

connection to prevent electromagnetic interference. Since the

SP2060 supports Auto MDI/MDI-X, it will automatically

detect whether the connected cable is of the straight type or

crossover type, and will conﬁgure itself to create the optimal

connection. Therefore, you can use either a straight or

crossover cable.

• The maximum length of a cable between a switching hub and

the SP2060 is 100 meters. Due to the quality of cables and

switching hub performance, however, proper operation at the

maximum length cannot be guaranteed in some cases.

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

SP2060 Owner’s Manual

Basic Operation

Changing the parameter values

You can adjust the parameter settings, such as EQ, according

to the speaker response or the acoustic environment of a par-

ticular venue. This section explains how to change the delay

time for Output channel 1 as an example.

1. Display the parameter setting you wish to

change. To change the delay time, ﬁrst press

the [DELAY] key to switch to the Delay

display.

Refer to “The Controls and Connectors” on page 21 for

information on the relationship between the parameters

and keys.

2. Select a channel for which you wish to

change the delay time. In this example, press

the OUTPUT 1 [SEL] key.

3. Press the [NEXT] key repeatedly until the

parameter you wish to change appears on the

screen. In this example, select the Time

parameter.

4. Press the [▲ INC]/[▼ DEC] keys to change the

parameter value.

The parameter value on the screen changes accordingly.

This section describes the function of the panel keys and re-

lated displays.

Some parameters will prompt you to confirm the operation

to reflect the change in the value.

In this case, a confirmation icon will appear on the display.

Press the [NEXT] key to move the cursor to the icon, then

press the [YES] key. A message prompts you to confirm.

Press the [YES] key to confirm the operation.

LEVEL

You can view and adjust the Input and Output channel lev-

els.

1. Press the [LEVEL] key to select the Level

display.

2. Press the [SEL] key for the target channel.

The corresponding channel is selected. The [SEL] key

LED for the selected channel lights up.

3. Press the [▲INC]/[▼DEC] keys to adjust the

input or output level.

Panel Operation

[▲ INC]

key

Press the [▲ INC]

key.

The value increases.

Hold down the

[▲ INC] key.

The value continues to

increase as long as you

hold down the key.

While holding down

the [▲ INC] key,

press the [▼ DEC]

key.

The value continues to

increase at a rate more

rapid than when you hold

down the [▲ INC] key.

[▼ DEC]

key

Press the [▼ DEC]

key.

The value decreases.

Hold down the

[▼ DEC] key.

The value continues to

decrease as long as you

down the key.

While holding down

the [▼ DEC] key,

press the [▲ INC]

key.

The value continues to

decrease at a rate more

rapid than when you hold

down the [▼ DEC] key.

OUT 1

ON/OFF = ON

OUT 1

TIME = 2.67ms

Parameter Range

INPUT A/B/SUM –∞, –138.00 through +10.00dB

OUTPUT 1-6 –

∞, –138.00 through +10.00dB

NOTE

When INPUT A/B LINK is turned On, the parameters for

channels A and B are linked and set to the same value

automatically.

SCENE EDIT

01:FOH(Event A)

Confirmation icon

Cursor

IN A

LEVEL =-138.00dB

IN B

LEVEL =-138.00dB

IN B

LEVEL =-138.00dB

Panel Operation

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

DELAY

You can set the signal delay time on each input and output

channel. Set the On/Off parameter to On to delay the signal,

and Off to bypass the delay.

1. Press the [DELAY] key to select the Delay

display.

2. Press the [SEL] key for the target channel.

The [SEL] key LED of the selected channel lights up,

and the corresponding channel name is displayed.

Pressing the [SEL] keys for Input channels A and B si-

multaneously will turn on the [SEL] key LEDs and select

channel SUM.

3. Press the [▲INC]/[▼DEC] keys to select On or

Off.

4. Press the [DELAY] or [NEXT] key to display

the Time parameter.

5. Press the [▲INC]/[▼DEC] keys to adjust the

delay time.

EQ (Equalizer)

An EQ boosts or cuts the level of specified frequency ranges.

The SP2060’s internal EQ processes input and output sig-

nals.

Input EQ

You can apply eight-band EQ to Input channels A, B, and

SUM.

Set the On/Off parameter to On to apply EQ to the signal,

and Off to not process the signal.

You can set the following parameters for each band.

You can select a type of filter for band 1 and band 8. All other

bands utilize a fixed parametric EQ.

• PEQ

This is a standard parametric equalizer.

• L.SHELF(Low Shelving)

Does not cut the lower frequency range, but cuts starting

from the vicinity of the cutoff frequency toward the higher

range at a specific rate. “6dB/Oct” and “12dB/Oct” stand

for the cut amount per octave.

• H.SHELF(High Shelving)

Does not cut the higher frequency range, but cuts starting

from the vicinity of the cutoff frequency toward the lower

range at a specific rate. “6dB/Oct” and “12dB/Oct” stand

for the cut amount per octave.

• HPF

This is a high pass filter (Q=0.7). The low frequency range

is mildly cut (12dB/Oct), creating a slow curve.

• LPF

This is a low pass filter (Q=0.7). The high frequency range

is mildly cut (12dB/Oct), creating a slow curve.

Parameter Range

INPUT A/B/SUM 0–1300.00msec

OUTPUT 1-6 0–500.00msec

NOTE

Channel SUM is a new channel created by applying the Level and

Mute settings to Input channel A and B respectively, then adding

both channel values.

IN A

ON/OFF = OFF

IN SUM

ON/OFF = OFF

IN SUM

ON/OFF = ON

IN B

TIME = 130.00ms

IN B

TIME = 120.00ms

Parameter Range Function

BYPASS ON/OFF

Sets the bypass for

each frequency range

to On or Off.

Q 16.0–0.1

Speciﬁes the width of

each frequency range.

FREQ

(Frequency)

20.0Hz–20.0kHz

Speciﬁes the center

frequency of each

frequency range.

GAIN

–18dB through

+18.00dB

Sets the gain of the

target frequency.

Parameter Range Function

TYPE

PEQ

L.SHELF 6dB/Oct

L.SHELF 12dB/Oct

H.SHELF 6dB/Oct

H.SHELF 12dB/Oct

HPF

LPF

Selects a type of ﬁlter.

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Panel Operation

SP2060 Owner’s Manual

1. Press the [EQ] key repeatedly to select the

EQ display.

2. Press the [SEL] key for the target channel.

The [SEL] key LED of the selected channel lights up,

and the corresponding channel name is displayed.

Pressing the [SEL] keys for channels A and B will turn on

the [SEL] key LEDs and select channel SUM.

3. Press the [EQ], [BACK] or [NEXT] key to

display the On/Off parameter.

4. Press the [▲INC] key to set the On/Off

parameter to On to apply EQ to the signal.

Press the [▼DEC] key to set the On/Off

parameter to Off to not process the signal.

5. Press the [BACK] or [NEXT] key to select the

Bypass, Type, Q, Freq, or Gain parameter.

6. Pressing the [EQ] key repeatedly will scroll

the bands from 1 through 8.

7. Press the [▲INC]/[▼DEC] keys to select the

value.

Output EQ

You can apply a 6-band EQ to Output channels 1–6.

Set the On/Off parameter to On to apply EQ to the signal,

and Off to not process the signal.

The parameters are the same as for the input EQ.

You can set the following parameters for each band.

• APF (All Pass Filter)

This filter passes all ranges of frequency, but changes only

the phase. It is used to align the phase in the crossover

range.

APF 1st rotates the phase by 0 through 180 degrees, and

APF 2nd rotates the phase by 0 through 360 degrees. APF

2nd requires the Q setting.

• Horn

A horn speaker typically features a roll-off in the higher

frequency component.

Horn EQ corrects this characteristics. For this purpose,

the gain is limited to 0dB or higher, and the frequency to

500Hz or higher.

IN A

ON/OFF = ON

IN SUM

ON/OFF = ON

IN SUM BAND 2

Q = 0.125

IN SUM BAND 3

Q = 0.125

Parameter Range Function

BYPASS ON/OFF

Sets the bypass

for each

frequency range

to On or Off.

TYPE

PEQ

L.SHELF 6dB/Oct

L.SHELF 12dB/Oct

H.SHELF 6dB/Oct

H.SHELF 12dB/Oct

HPF

LPF

APF 1st

APF 2nd

Horn

Selects a type of

ﬁlter.

Q 63.0–0.1

Speciﬁes the

width of each

frequency range.

FREQ

(Frequency)

20.0Hz–20.0kHz

Speciﬁes the

frequency of each

band.

GAIN

–18dB through

+18.00dB

Sets the gain of

the target

frequency.

Panel Operation

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

ROUTING

Input routing

You can select either analog or digital input signals. This se-

lection links to the word clock master setting. You can also

route the left channel of an input signal received at the [IN-

PUT A] or [DIGITAL IN] connector to both Input chan-

nels A and B.

1. Press the [ROUTING] key to select the

Routing display.

2. Press the [▲INC]/[▼DEC] keys to select an

input signal source.

Output routing

You can route Input channel A, B, and SUM signals to the

Crossover input.

The following three channels are available:

• IN A

• IN SUM

• IN B

1. Press the [ROUTING] key to select the

Routing display.

2. Press the [SEL] key for the target Output

channel.

The [SEL] key LED for the selected channel lights up.

The [SEL] key LED for each channel that shares the

same component flashes. The selected channel name ap-

pears on the display.

3. Press the [▲INC]/[▼DEC] keys to select an

input source to be routed to the Crossover.

Option Input Signal Selection

Word Clock

Master

ANA A/B

A signal at the [INPUT A]

connector is routed to

channel A, and a signal at

the [INPUT B] connector

to channel B.

Internal clock:

96kHz

ANA A/A

A signal at the [INPUT A]

connector is routed to

channels A and B.

DIG L/R

A left channel signal is

routed to channel A, and

a right channel signal to

channel B.

Incoming AES/

EBU signal

DIG L/L

A left channel signal is

routed to channels A and

HINT

You can check the word clock status on the Utility display. See

page 34.

NOTE

Signals are muted while they are switched between analog and

digital to avoid noise.

INPUT SELECT

SOURCE = ANA A/B

INPUT SELECT

SOURCE = ANA A/A

OUT 2

SOURCE = IN A

OUT 4

SOURCE = IN A

OUT 4

SOURCE = IN SUM

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Panel Operation

SP2060 Owner’s Manual

X-OVER (Crossover)

Setting the Crossover

Input signals can be divided into specified frequency ranges

to suit speaker response characteristics prior to output.

The number of division is determined to 1-way through 6-

way, depending on the selected component.

1. Press the [X-OVER] key repeatedly until the X-

Over display appears on the screen.

2. Press the [SEL] key for the target Output

channel.

The [SEL] key LED of the selected channel lights up,

and the corresponding channel name is displayed.

3. Press the [NEXT]/[BACK] keys to select a

parameter to edit.

4. Press the [▲INC]/[▼DEC] keys to set the

parameter value.

Parameter Range Function

LEVEL

–

∞, –138.00 through

+10.00dB

Adjusts the level of the

signal input to the

Crossover. The same

Level setting is used

for the output channels

of a component.

POLARITY

NORMAL

INVERTED

The output signal

phase for each

frequency range is

inverted.

HPF

Refer to Step 4.

LPF

OUT 1 LPF

FREQ = 20.0kHz

OUT 3 LPF

FREQ = 20.0kHz

OUT 3 LPF

TYPE =24AdjustGc

Parameter Range Function

HPF

TYPE

Thru

6dB/Oct

12dB/Oct AdjustGc

12dB/Oct Butrwrth

12dB/Oct Bessel

12dB/Oct Linkwitz

18dB/Oct AdjustGc

18dB/Oct Butrwrth

18dB/Oct Bessel

24dB/Oct AdjustGc

24dB/Oct Butrwrth

24dB/Oct Bessel

24dB/Oct Linkwitz

36dB/Oct AdjustGc

36dB/Oct Butrwrth

36dB/Oct Bessel

48dB/Oct AdjustGc

48dB/Oct Butrwrth

48dB/Oct Bessel

48dB/Oct Linkwitz

Selects an

attenuation

amount per

octave, and a

type of ﬁlter.

If you select

“Thru,” no ﬁlter

will be applied.

FREQ

(Frequency)

20.0Hz–20.0kHz

Speciﬁes the

cutoff frequency

of the high pass

ﬁlter.

Gc –6dB through +6dB

You can set the

gain for the cutoff

frequency (Gc)

when you select

“AdjustGc

(Adjustable Gc)”

for the Type

parameter.

LPF

TYPE

Thru

6dB/Oct

12dB/Oct AdjustGc

12dB/Oct Butrwrth

12dB/Oct Bessel

12dB/Oct Linkwitz

18dB/Oct AdjustGc

18dB/Oct Butrwrth

18dB/Oct Bessel

24dB/Oct AdjustGc

24dB/Oct Butrwrth

24dB/Oct Bessel

24dB/Oct Linkwitz

36dB/Oct AdjustGc

36dB/Oct Butrwrth

36dB/Oct Bessel

48dB/Oct AdjustGc

48dB/Oct Butrwrth

48dB/Oct Bessel

48dB/Oct Linkwitz

Selects an

attenuation

amount per

octave, and a

type of ﬁlter.

If you select

“Thru,” no ﬁlter

will be applied.

FREQ

(Frequency)

20.0Hz–20.0kHz

Speciﬁes the

cutoff frequency

of the low pass

ﬁlter.

Gc –6dB through +6dB

You can set the

gain for the cutoff

frequency (Gc)

when you select

“AdjustGc

(Adjustable Gc)”

for the Type

parameter.

Panel Operation

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

• Thru

No filter is applied. The original characteristics are kept

with no attenuation for all frequency ranges.

• AdjustGc (Adjustable Gc)

Filters with an Adjustable Gc enable you to adjust the gain

at the cutoff frequency in the range of –6dB through

+6dB. With Gc set to –3dB, the filter is practically a But-

terworth filter. And with Gc set to –6dB, the filter is prac-

tically a Linkwitz-Riley filter.

• Butrwrth (Butterworth)

This filter is the most common type of filter. It has a flat

pass band and a –3dB gain at the cutoff frequency.

• Bessel

This filter focuses on the phase characteristics. Although it

has a more gradual roll-off than a Butterworth filter, it will

pass a square wave without causing ringing.

• Linkwitz (Linkwitz-Riley)

This filter features the square of the second order. When

the output signal from its LPF and HPF are combined, the

gain over the entire range is +/–0dB. It has a flat pass band

and a –6dB gain at the cutoff frequency.

LIBRARY

Using libraries facilitates the recall of optimal speaker set-

tings. Up to 60 libraries are available for each component via

the DME Designer application.

Displaying the current library

Pressing the [X-OVER] key repeatedly will select the Cur-

rent Library display, Library List display, or X-Over display,

in this order.

The title of the library most recently recalled for each com-

ponent will be displayed.

Recalling a library

Follow the steps below to recall a library:

1. Press the [X-OVER] key repeatedly until the

Library List display appears on the screen.

2. Press the [SEL] key of an Output channel for

a component for which you wish to recall a

library.

3. Press the [▲INC]/[▼DEC] keys to select a

library.

4. Press the [NEXT/RECALL] key.

A confirmation message will appear.

NOTE

• The type names are abbreviated on the SP2060 screen.

For example, “24dB/Oct Bessel” is displayed as “24Bessel.”

• Gc page is displayed if you select “Adjust Gc” for the Type

parameter.

NOTE

Libraries cannot be displayed or recalled for Input channels. If

you press an Input channel [SEL] key, a message appears.

CURRENT LIBRARY

IF2112/95

LIBRARY LIST

IF2112/64

LIBRARY LIST

IF2112/64

LIBRARY RECALL

ARE YOU SURE?

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Panel Operation

SP2060 Owner’s Manual

5. To conﬁrm the selection, press the [YES] key.

The library is recalled and the unit returns to the Library

List display.

To cancel the recall operation, press the [NO] key, in-

stead of the [YES] key. The unit returns to the Library

List display.

LIMITER

You can set up the Output channel limiter.

The Limiter precludes signal levels higher than a specified

threshold to avoid speaker damage from excess output level.

1. Press the [LIMITER] key to select the Limiter

display.

2. Press the [SEL] key for the target channel.

The [SEL] key LED of the selected channel lights up,

and the corresponding channel name is displayed.

3. Press the [LIMITER], [BACK] or [NEXT] key to

display the On/Off parameter.

4. Press the [▲INC] key to set the On/Off

parameter to On to apply the Limiter to the

signal. Press the [▼DEC] key to set the On/

Off parameter to Off to cancel the Limiter.

5. Press the [NEXT]/[BACK] keys to select a

parameter to edit.

6. Press the [▲INC]/[▼DEC] keys to set the

parameter value.

SCENE

About a scene

The SP2060 enables you to store various parameter settings

as part of scene, and recall them via the front panel or re-

motely from DME Designer.

You can store the following settings in a scene:

• Conﬁguration

•Routing

•Parameter sets of all components

• Scene titles

• Scene protection status

• INPUT A/B LINK

• The title of the library most recently recalled

HINT

You can use the library data for speaker processor components for

DME64N/24N that you have created using DME Designer.

Parameter Range Function

THRESHOLD –54 through 0dB

Sets the threshold

value.

ATTACK

FAST

MID

SLOW

MANUAL (0–

120.0ms)

Sets the attack time.

RELEASE

FAST

MID

SLOW

MANUAL

44.1kHz: 6ms–46s,

48kHz: 5ms–42.3s,

88.2kHz: 3ms–23s,

96kHz: 3ms–21.1s

Sets the release time.

If you select Fast,

Mid, or Slow, the unit

automatically sets the

optimum value based

on the maximum

wave length of audio

input to the Limiter.

NOTE

•You can set the attack time only when “Manual” is selected for

the Attack parameter.

•You can set the release time only when “Manual” is selected for

the Release parameter.

LIBRARY LIST

IF2112/95

HINT

You can protect a scene to forbid overwriting.

OUT 1

ON/OFF = ON

OUT 4

ON/OFF = ON

OUT 4

THRESHOLD= -54dB

Panel Operation

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

Scenes are stored in the preset area and user area.

Preset area

There is a preset scene for each of 12 configurations. These

scenes are numbered 1 through 12. Each scene title has the

same name as the corresponding configuration title.

User area

The user area can accommodate up to 87 user scenes, which

you can store and recall at your discretion. These scenes are

numbered 13 through 99.

Scene indication

The upper row indicates a scene number, property, and title.

The bottom row indicates the configuration title.

Scene property includes the following types:

Recalling a scene

Follow the steps below to recall a scene (1–99):

1. Press the [SCENE] key to select the Scene

Selection display.

2. Press the [▲INC]/[▼DEC] keys to select a

scene number.

While you are selecting a scene, the scene number and ti-

tle will be flashing.

3. Press the [RECALL] key.

A confirmation message will appear.

4. Press the [YES] key.

The scene is recalled and its number becomes the current

scene number.

To cancel the recall operation, press the [NO] key, in-

stead of the [YES] key. The unit returns to the Scene Se-

lection display.

No.1. [3x2way ]

No.2. [3x2way L ]

No.3. [2x(2way+Sub) ]

No.4. [2x(2way+Sub)L ]

No.5. [2x2way+2xAux ]

No.6. [2x2way+2xAux L ]

No.7. [2x3way ]

No.8. [2x3way L ]

No.9. [4way+2xAux ]

No.10. [5way+Aux ]

No.11. [6way ]

No.12. [Multi Zone ]

Preset scene

Protected user scene

Unprotected user scene

NOTE

After you recall a scene, if you edit a parameter, an icon

appears in the lower right corner on the screen.

25:FOH(Event A)

[2x(2way+SUB)L]

Scene propertyScene number Title

Configuration title

HINT

You can also recall a scene using the DME Designer application.

NOTE

If recalling a scene has changed the conﬁguration, audio output

will be muted momentarily.

NOTE

If no data is included in the currently-selected scene, the message

“No Scene” appears.

NOTE

If the selected scene contains no data or User Lock is turned on

for the scene, a status message appears.

25:FOH(Event A)

[2x(2way+SUB)L]

33:RECALL

ARE YOU SURE?

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Panel Operation

SP2060 Owner’s Manual

Storing a scene

Follow the steps below to store a scene (13–99) to the user

area:

1. Press the [SCENE] key to select the Scene

Selection display.

2. Press the [▲INC]/[▼DEC] keys to select a

scene number.

3. Press the [BACK/STORE] key.

A confirmation message will appear.

4. Press the [YES] key.

The scene is stored and its number becomes the current

scene number.

To cancel the store operation, press the [NO] key, in-

stead of the [YES] key. The unit returns to the Scene Se-

lection display.

Changing a scene title

Follow the steps below to change the title (up to 13 charac-

ters) of the scene stored for the current scene number:

1. Press the [SCENE] key repeatedly until the

Scene Edit display appears on the screen.

2. Press the [BACK]/[NEXT] keys to move the

cursor to a character you want to edit.

3. Press the [▲INC]/[▼DEC] keys to change the

character.

4. When you ﬁnish editing the title, press the

[NEXT] key repeatedly to move the cursor to

the icon, then press the [YES] key.

A confirmation message will appear.

5. To conﬁrm the edit, press the [YES] key.

The title is changed and the unit returns to the Scene

Edit display.

Protecting a scene

Follow the steps below to protect a scene:

1. Press the [SCENE] key repeatedly until the

Scene Edit display appears on the screen.

2. Press the [▲INC]/[▼DEC] keys to select a

scene number.

3. Press the [NEXT] key to move the cursor to

the scene property icon.

4. Press the [▲INC]/[▼DEC] keys to turn

protection on or off.

The protection icon flashes.

HINT

You can also store a scene using the DME Designer application.

NOTE

You cannot change the title of any protected User scenes.

25:FOH(Event A)

[2x(2way+SUB)L]

72:STORE

ARE YOU SURE?

SCENE EDIT

73:FOH(Event A)

SCENE EDIT

73:FOH(Event A)

HINT

Holding down the [▲INC]/[▼DEC] keys will increase the speed

at which the characters scroll.

SCENE EDIT

ARE YOU SURE?

SCENE EDIT

73:FOH(Event A)

SCENE EDIT

73:FOH(Event A)

SCENE EDIT

73 FOH(Event A)

Panel Operation

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

5. Press the [NEXT] key repeatedly to move the

cursor to the icon, then press the [YES]

key.

A confirmation message will appear.

6. To conﬁrm the edit, press the [YES] key.

The unit reflects the edit and returns to the Scene Edit

display.

Deleting a scene

Follow the steps below to delete a scene:

1. Press the [SCENE] key repeatedly until the

Scene Delete display appears on the screen.

2. Press the [▲INC]/[▼DEC] keys to select a

scene to delete.

3. Press the [NEXT] key to move the cursor to

the icon, then press the [YES] key.

A confirmation message will appear.

4. To conﬁrm the operation, press the [YES] key.

The operation is executed and the unit returns to the

Scene Delete display.

UTILITY

The Utility function enables you to view the word clock sta-

tus and make network settings. See page 37 for more infor-

mation on making network settings.

INPUT A/B LINK

Follow the steps below to link the Input channel A and B pa-

rameters:

When INPUT A/B LINK is turned On, the parameters for

channel A and B are linked and set to the same value auto-

matically.

The following components will be linked:

• INPUT LEVEL

• INPUT EQ

• INPUT DELAY

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the INPUT A/B LINK page

appears.

3. Press the [▲INC] key to link the parameters.

“ON” flashes on the screen.

4. Press the [NEXT] key to move the cursor to

the icon.

5. Press the [YES] key.

A confirmation message will appear.

HINT

You can turn protection on and off from the DME Designer

application.

NOTE

You cannot delete preset scenes, protected scenes, and current

scene.

SCENE EDIT

ARE YOU SURE?

SCENE DELETE

72:FOH(Event A)

SCENE DELETE

ARE YOU SURE?

NOTE

The channel SUM parameters cannot be linked.

INPUT A/B LINK

OFF

INPUT A/B LINK

ARE YOU SURE?

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Panel Operation

SP2060 Owner’s Manual

6. To conﬁrm the operation, press the [YES] key.

The flashing “ON” (or “OFF”) lights up steadily, and the

cursor returns to the “ON (or OFF)” position.

To cancel the operation and return to the original set-

ting, press the [NO] key.

User Lock

Parameter settings can be “locked” temporarily to prevent

accidental mis-operation. This function is useful to avoid

unintentional operations or to prevent others from operating

the panel controls.

The following operations are the User Lock target.

* Editing the parameters

* Recalling and storing a scene

* Changing a scene title

* Changing the scene protection status

* Recalling a library

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the User Lock page appears.

3. Press the [▲INC] key to turn User Lock on. To

cancel User Lock, press the [▼DEC] key.

“ON” flashes on the screen.

4. Press the [NEXT] key to move the cursor to

the icon.

5. Press the [YES] key.

A confirmation message will appear.

6. To conﬁrm the operation, press the [YES] key.

A status message appears, and User Lock becomes active.

Setting the Last Memory Resume

You can select whether at the startup the SP2060 recalls the

scene selected before you turned off the power to the device,

or it starts up with the same status as when it was shut down

last time. The default setting is “ON.”

OFF: At the startup, the SP2060 will recall the scene select-

ed before you turned off the power to the device.

ON: The SP2060 will start up with the same status as

when it was shut down last time.

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the Last Memory Resume

page appears.

NOTE

If you set INPUT A/B LINK to “ON,” the linked parameters for

channel A will be copied to channel B parameters.

NOTE

•You can mute or unmute, or cancel User Lock even if the User

Lock function is turned on.

• The User Lock function is effective only for the panel controls

on the SP2060, and does not affect any control signals from

external devices.

INPUT A/B LINK

ARE YOU SURE?

USER LOCK

OFF

USER LOCK

HINT

•A short cut to turn on the User Lock function is to hold down

the [MUTE] key for two seconds or longer.

•A short cut to turn off the User Lock function is to hold down

the [MUTE] key for two seconds or longer.

USER LOCK

ARE YOU SURE?

Panel Locked

LAST MEM. RESUME

Panel Operation

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

3. Press the [▲INC] key so that the SP2060 will

start up with the same status as when it was

shut down last time. Press the [▼DEC] key so

that at the startup the SP2060 will recall the

scene selected before you turned off the

power to the device.

“ON” flashes on the screen.

4. Press the [NEXT] key to move the cursor to

the icon.

5. Press the [YES] key.

A confirmation message will appear.

6. To conﬁrm the operation, press the [YES] key.

The selection is applied and the unit returns to the Last

Memory Resume page.

Displaying the label

You can view the label for the SP2060 that you have set on

DME Designer.

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the Label page appears.

The unit displays the label you created on DME Design-

er.

Displaying word clock

Word clock changes in accordance with input routing set-

tings.

You can view the current word clock status on the display.

One of the following six word clock sources will be dis-

played:

For analog input signals:

The internal clock (Fs=96kHz) is used.

• INT:96kHz : Internal clock (96kHz)

For digital input signals:

The SP2060 synchronizes to an external clock (input at the

AES/EBU connector).

• EXT:44.1kHz : External clock (44.1kHz)

• EXT:48kHz : External clock (48kHz)

• EXT:88.2kHz : External clock (88.2kHz)

• EXT:96kHz : External clock (96kHz)

• EXT:UNLOCK : Unlock to external clock

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display page will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the W. Clock page appears.

NOTE

•You cannot edit the label on the SP2060.

•Up to 14 characters from the top can be displayed.

LAST MEM. RESUME

ARE YOU SURE?

LABEL

[FoH L ]

NOTE

If no signal exists at the [DIGITAL INPUT] connector while

digital input is selected, or if the SP2060 cannot somehow lock to

the incoming signal, an error message appears.

W.CLOCK

[INT: 96kHz]

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Panel Operation

SP2060 Owner’s Manual

Checking the backup battery

Follow the steps below to check the internal backup battery

status:

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the Battery page appears.

The remaining battery charge is displayed as follows:

Displaying the firmware version

Follow the steps below to view the current firmware version

number:

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display page will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the Version page appears.

The page indicates the current firmware version number.

You can update the SP2060 firmware via DME Designer.

Refer to the DME Designer Owner’s Manual for details.

You can also download the latest firmware from the follow-

ing Yamaha website.

http://www.yamahaproaudio.com/

Initializing the SP2060

Follow the steps below to initialize the internal memory:

You can select one of the following initialization types:

*Initializing the current scene backup [CURRENT

BACKUP]

*Initializing all user settings (excluding the libraries) to

the factory settings [WITHOUT LIB.]

*Initializing all settings to the factory settings

[FACTORY SETUP]

1. Turn off the power to the SP2060.

2. Turn on the power to the SP2060 while

holding down the [BACK/STORE] key.

The Initialization display appears.

3. Press the [▲INC]/[▼DEC] keys to select a

type of initialization.

4. Press the [NEXT] key to move the cursor to

the icon, then press the [YES] key.

The Initialization operation starts. During initialization,

the following status message appears:

When initialization is completed, the SP2060 displays

the following status message, then automatically restarts.

[OK ] Plenty of charge

[Low Battery] Charge is getting low.

[No Battery ]

Memory data may be lost. Or, no battery

is installed.

“Low Battery” or “No Battery” will appear when the

battery charge is getting low. In this case, save the data to

an external device (such as a computer) immediately, then

ask the Yamaha dealer to replace the backup battery.

HINT

If there is any issue with the backup battery, the SP2060 displays

“Low Battery,” “Critical Battery,” or “No Battery” when you turn

on the power to the unit.

BATTERY

[OK ]

CAUTION

VERSION

[V1.00]

When the internal memory is initialized, all data stored in

the memory will be lost. Use caution when you execute

this function.

NOTE

To cancel the initialization operation, select “Exit” and conﬁrm

the cancellation. Alternatively, simply turn off the power to the

SP2060.

CAUTION

INITIALIZE

FACTORY SETUP

INITIALIZE

EXECUTING..

INITIALIZE

COMPLETED!

Panel Operation

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

Mute

When Mute is on, the corresponding Input or Output chan-

nel audio is muted.

You can determine the channel Mute status by checking the

corresponding channel [MUTE] key LED.

• MUTE OFF : Dark

• MUTE ON : Illuminated

1. Press the [MUTE] key to select the Mute

display.

2. Press the [SEL] key for the target channel.

The channel audio is muted and the [MUTE] key LED

lights up. Pressing the channel [SEL] key repeatedly tog-

gles between Mute on and off.

NOTE

You can mute or unmute even if the User Lock function is turned

NOW SELECT KEYS

ACT "MUTE" ->

1BA

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

SP2060 Owner’s Manual

This section describes the network-related settings on the

SP2060 that you need to make when you connect a comput-

er or other external device to the SP2060 [NETWORK]

connector.

Setting a Device Group

A “device group” is a group of multiple SP2060 units that

can be operated in sync via DME Designer. Follow the steps

below to assign each SP2060 in a device group as master or

slave. Each device group must have one master. All other de-

vices in the group are assigned as slave.

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the Device Group page

appears.

3. Press the [▲INC]/[▼DEC] keys to select

“MASTER” or “SLAVE.”

When you change the setting, the parameter setting

flashes.

4. Press the [NEXT] key to move the cursor to

the icon, then press the [YES] key.

A confirmation message will appear.

5. To conﬁrm the setting, press the [YES] key.

The selection is applied and the unit returns to the De-

vice Group page.

Setting the IP Address

Follow the steps below to set the IP address for each SP2060.

Each group of digits between periods in an IP address is

called “octet.” These groups of digits are called “1st octet,”

“2nd octet,” etc., starting from the left-most digit group.

You cannot specify 0, 127, and 223 through 255 for the 1st

octet of the network address.

You can specify the following range of values for the 4th oc-

tet.

Master : 2–253

Slave : 3–253

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the IP Address page appears.

3. Press the [NEXT]/[BACK] keys to move the

cursor to an octet you want to specify.

4. Press the [▲INC]/[▼DEC] keys to change the

value.

When you change the value, the octet flashes.

5. Press the [NEXT] key to move the cursor to

the icon, then press the [YES] key.

A confirmation message will appear.

Network Settings

NOTE

When connecting a computer to an SP2060 via Ethernet, you

must install the appropriate DME-N Network driver on the

computer. You can download the DME-N Network driver from

the Yamaha website.

DEVICE GROUP

MASTER

DEVICE GROUP

SLAVE

DEVICE GROUP

ARE YOU SURE?

NOTE

•Subnet mask is ﬁxed at 255.255.255.0.

•Gateway address is the same network address as the IP address.

The host address is automatically set to 254.

IP ADDRESS

192.168.000.003

Network address Host address

IP ADDRESS

192.168.000.002

IP ADDRESS

192.168.000.003

IP ADDRESS

ARE YOU SURE?

Network Settings

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

6. To conﬁrm the setting, press the [YES] key.

The setting is applied and the unit returns to the IP Ad-

dress page.

Setting the Master ID

The SP2060 units that are assigned as slaves in a device

group follow the master SP2060 in the same group via com-

munication. Follow the steps below to set the master ID on

the slave SP2060 units. Use the 4th octet of the IP address of

the master unit as the Master ID parameter value.

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the Master ID page appears.

3. Press the [▲INC]/[▼DEC] keys to set the

value to the same number as the 4th octet of

the master SP2060 IP address.

4. Press the [NEXT] key to move the cursor to

the icon, then press the [YES] key.

A confirmation message will appear.

5. To conﬁrm the setting, press the [YES] key.

The setting is applied and the unit returns to the Master

ID page.

To cancel the operation and return to the original set-

ting, press the [NO] key, instead of the [YES] key.

Setting Link Mode

Follow the steps below to select 100Base-TX or 10Base-T for

the [NETWORK] connector speed.

100Base-TX

The [NETWORK] connector basically operates as 100Base-

TX, but automatically switches to 10Base-T if the network

environment is not compatible with 100Base-TX.

10Base-T

The [NETWORK] connector is compatible with 10Base-T

operation.

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the Link Mode page appears.

3. Press the [▲INC] key to select 100Base-TX,

and the [▼DEC] key to select 10Base-T.

When you change the setting, the parameter setting

flashes.

4. Press the [NEXT] key to move the cursor to

the icon, then press the [YES] key.

A confirmation message will appear.

5. To conﬁrm the setting, press the [YES] key.

The unit reflects the edit and returns to the Link Mode

page.

NOTE

This parameter can be set from 2 through 253.

MASTER ID

253

MASTER ID

ARE YOU SURE?

NOTE

Depending on the speciﬁcations of the connected network

devices (such as a switching hub, router, etc.), changing Link

Mode may cause the SP2060 to be unable to reconnect to the

network. In this case, turn the power to the SP2060 off and then

on. The SP2060 will reconnect to the network.

LINK MODE

100BASE-TX

LINK MODE

10BASE-T

LINK MODE

ARE YOU SURE?

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

Network Settings

SP2060 Owner’s Manual

Viewing the MAC Address

Follow the steps below to view the SP2060 MAC address:

1. Press the [UTILITY] key to select the Utility

display.

The most recently used Utility display will appear.

2. Press the [UTILITY], [NEXT] or [BACK] key

repeatedly until the MAC Address page

appears.

The bottom row indicates the MAC address.

NOTE

In some cases, you may not need to set the MAC address via the

DME-N Network driver when the SP2060 is communicating

with DME Designer.

MAC ADDRESS

[00A0DE250123]

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

About Preset Libraries

File name

•pa........................ Passive mode*

•bi........................ Bi-amp mode

• tri........................ Tri-amp mode

• sub...................... Combining with a subwoofer**

• moni................... For a ﬂoor monitor

*Yamaha Installation Series speakers are designed to be used without a speaker processor when Passive mode is

selected. However, using a speaker processor will improve the performance signiﬁcantly.

** This setting is for full-range speakers. Subwoofer settings are not included.

Subwoofer

• “_sub” settings for 12-inch or 15-inch 3-way full-range speakers are designed for a combination with IS1118,

IS1215, or IS1218.

• The IS1118, IS1215, and IS1218 settings are speciﬁed for a monaural subwoofer usage.

• The full-range and subwoofer level balance varies depending on the number of speakers used, installation

conditions, and applications.

•If the full-range speaker bafﬂe and subwoofer bafﬂe are aligned, the speaker polarity will be positive and in-

phase.

Depending on the installation conditions of the subwoofers, you might achieve better results if the subwoofer

phase is inverted.

Limiter

• The default value of the threshold level has been speciﬁed based on the maximum analog output level of

+24dBu and amp voltage gain of 26dB (which corresponds to “ATT –6dB” if you are using a Yamaha PC

series ampliﬁer that features a voltage gain of 32dB).

If you are not using the output levels referenced above, change the threshold level.

For example, if you are using an ampliﬁer with a voltage gain of 30dB, lower the threshold level by 4dB.

•Attack time and Release time are both set to “Mid.”

• The Limiter may not completely protect the speakers. Use the Limiter if they suit your environment.

References

LIBRARY LIST

IF211264_pa_sub

LIBRARY LIST

IF2112AS_bi_moni

Model name Drive

mode

Subwoofer usage Model name Drive

mode

Floor monitor

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

References

SP2060 Owner’s Manual

Libraries for 1-way speaker processors

The following table shows typical subwoofer settings when it is combined with Yamaha In-

stallation Series speakers.

The following table shows the settings for Yamaha Installation Series speakers (full-range,

passive mode).

NOTE

These libraries also apply to 2-way speakers that are used in passive mode.

Target speakers Library name Meaning

IS1118 and IS1218 IS1118_IS1218

This setting can be shared by IS1118 and IS1218 when IF2112

(M), IF2115 (M) or IF3115 is combined.

IS1215 IS1215

This setting is for IS1215 when IF2112 (M), IF2115 (M) or IF3115

is combined.

Standard subwoofer Sub_5inch&8inch

This LPF setting can be shared by standard subwoofers when

IF2205, IF2108, or IF2208 is combined.

Target speakers Library name Subwoofer

usage*

For a ﬂoor

monitor

IF2205

IF2205 – –

IF2205_sub ✓ –

IF2108

IF2108 – –

IF2108_sub ✓ –

IF2108_moni – ✓

IF2208

IF2208 – –

IF2208_sub ✓ –

IF2208_moni – ✓

IF2112/AS

IF2112AS_pa – –

IF2112AS_pa_sub ✓ –

IF2112AS_pa_moni – ✓

IF2112/64

IF211264_pa – –

IF211264_pa_sub ✓ –

IF2112/95

IF211295_pa – –

IF211295_pa_sub ✓ –

IF2112/99

IF211299_pa – –

IF211299_pa_sub ✓ –

IF2112M/64

IF2112M64_pa – –

IF2112M64_pa_sub ✓ –

IF2112M/95

IF2112M95_pa – –

IF2112M95_pa_sub ✓ –

IF2112M/99

IF2112M99_pa – –

IF2112M99_pa_sub ✓ –

IF2115/AS

IF2115AS_pa – –

IF2115AS_pa_sub ✓ –

IF2115AS_pa_moni – ✓

IF2115/64

IF211564_pa – –

IF211564_pa ✓ –

References

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

* This setting is for full-range speakers. Subwoofer settings are not included.

Libraries for 2-way speaker processors

The following table shows the settings for Yamaha Installation Series speakers (full-range,

bi-amp mode).

IF2115/95

IF211595_pa – –

IF211595_pa_sub ✓ –

IF2115/99

IF211599_pa – –

IF211599_pa_sub ✓ –

IF2115M/64

IF2115M64_pa – –

IF2115M64_pa_sub ✓ –

IF2115M/95

IF2115M95_pa – –

IF2115M95_pa_sub ✓ –

IF2115M/99

IF2115M99_pa – –

IF2115M99_pa_sub ✓ –

NOTE

These libraries also apply to 3-way speakers (including a combination of IL series and IH series speakers) that are used in bi-

amp mode.

Target speakers Library name Subwoofer

usage*

For a ﬂoor

monitor

IF2112/AS

IF2112AS_bi – –

IF2112AS_bi_sub ✓ –

IF2112AS_bi_moni – ✓

IF2112/64

IF211264_bi – –

IF211264_bi_sub ✓ –

IF2112/95

IF211295_bi – –

IF211295_bi_sub ✓ –

IF2112/99

IF211299_bi – –

IF211299_bi_sub ✓ –

IF2112M/64

IF2112M64_bi – –

IF2112M64_bi_sub ✓ –

IF2112M/95

IF2112M95_bi – –

IF2112M95_bi_sub ✓ –

IF2112M/99

IF2112M99_bi – –

IF2112M99_bi_sub ✓ –

IF2115/AS

IF2115AS_bi – –

IF2115AS_bi_sub ✓ –

IF2115AS_bi_moni – ✓

IF2115/64

IF211564_bi – –

IF211564_bi_sub ✓ –

Target speakers Library name Subwoofer

usage*

For a ﬂoor

monitor

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

References

SP2060 Owner’s Manual

* This setting is for full-range speakers. Subwoofer settings are not included.

The following table shows the settings for Yamaha Installation Series speaker IL series along

with IH series.

Libraries for 3-way speaker processors

The following table shows the settings for Yamaha Installation Series speakers (full-range,

tri-amp mode).

The following table shows the settings for Yamaha Installation Series speaker IL series along

with IH series.

IF2115/95

IF211595_bi – –

IF211595_bi_sub ✓ –

IF2115/99

IF211599_bi – –

IF211599_bi_sub ✓ –

IF2115M/64

IF2115M64_bi – –

IF2115M64_bi_sub ✓ –

IF2115M/95

IF2115M95_bi – –

IF2115M95_bi_sub ✓ –

IF2115M/99

IF2115M99_bi – –

IF2115M99_bi_sub ✓ –

IF3115/64

IF311564_bi – –

IF311564_bi_sub ✓ –

IF3115/95

IF311595_bi – –

IF311595_bi_sub ✓ –

IH2000/64 IH200064_bi – –

IH2000/95 IH200095_bi – –

Target speakers Library name Meaning

IL1115 and IH2000/64 IL1115+IH64_pa Combination of IL1115 and IH2000/64 (passive mode)

IL1116 and IH2000/95 IL1115+IH95_pa Combination of IL1115 and IH2000/95 (passive mode)

Target speakers Library name Subwoofer

usage

IF3115/64

IF311564_tri –

IF311564_tri_sub ✓

IF3115/95

IF311595_tri –

IF311595_tri_sub ✓

Target speakers Library name Meaning

IL1115 and IH2000/64 IL1115+IH64_bi Combination of IL1115 and IH2000/64 (bi-amp mode)

IL1115 and IH2000/95 IL1115+IH95_bi Combination of IL1115 and IH2000/95 (bi-amp mode)

Target speakers Library name Subwoofer

usage*

For a ﬂoor

monitor

References

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

Display Messages

Warning and error messages

* Do NOT turn off the power to the SP2060 while the unit displays the message “DO NOT TURN OFF!” at the bottom of the display.

Message Meaning Action

Duplicate IP Adr. Duplicate IP addresses. Change the IP addresses so that there are no duplicates.

Illegal MAC Adr. An illegal MAC address has been encountered.

This could be due to a hardware malfunction. Refer this

problem to a contact a Yamaha dealer.

Invalid IP Adr. The IP address is not set properly. Set an appropriate network IP address.

Network Error

A cable is disconnected, the power to the

connected switching hub or router is turned off, or a

cable is not in proper condition.

Connect the cables properly, and make sure that the hub

and/or router are operating correctly.

No MAC Adr. MAC address not speciﬁed.

This could be due to a hardware malfunction. Refer this

problem to a Yamaha dealer.

No Battery

The internal battery is completely discharged or not

installed.

If you turn off the power to the unit, the current settings will

be lost and reset to the default values. Stop operating the

unit, and contact a Yamaha dealer for battery replacement.

Critical Battery

The internal battery is almost discharged. Your data

may be lost.

If you turn off the power to the unit, the current settings may

be lost and reset to the default values. Stop operating the

unit, and contact a Yamaha dealer for battery replacement.

Low Battery The backup battery voltage is low.

This does not affect the operation of the unit. However, if you

continue using the unit, the settings may be lost and reset to

the default values. Contact a Yamaha dealer for battery

replacement at your earliest convenience.

Recovering

A program update attempt has failed, and the

previous program is currently being restored.

Do NOT turn power off while the unit is displaying this

message. If the update attempt repeatedly fails, there may

be a hardware malfunction. Refer this problem to a Yamaha

dealer.

Scene Recall Err A scene recall attempt has failed.

Recall the scene again.

If the problem persists, contact a Yamaha dealer.

Saving Failed A save operation has failed.

This could be due to a hardware malfunction. Refer this

problem to a Yamaha dealer.

Param Access Err Current setting cannot be displayed. Save the current setting by using DME Designer, then

initialize the unit. If the problem persists, contact a Yamaha

dealer.

Param Set Err Current setting cannot be changed.

W.Clk Unlocked

A usable word clock signal is not being received or

cannot be detected.

Recheck all word clock connections and internal

parameters.

DevGrp Sync Err

The device group conﬁguration set via DME

Designer does not match the real conﬁguration.

Use DME Designer to go off-line, create a conﬁguration that

correctly matches the actual conﬁguration, and then go

back on-line to synchronize the conﬁguration.

System Error A system error has occurred.

Save the current setting by using DME Designer, then

initialize the unit. If the problem persists, contact a Yamaha

dealer.

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

References

SP2060 Owner’s Manual

Status messages

* Do NOT turn off the power to the SP2060 while the unit displays the message “DO NOT TURN OFF!” at the bottom of the display.

Troubleshooting

Message Meaning

Connecting Connecting to the network.

Download Success The program has been successfully updated.

Downloading Program update in progress. Do NOT turn power off while the unit displays this message.

File Operating

A ﬁle operation is in progress during which the computer manipulates scene data. Do NOT turn power off

while the unit displays this message.

Network Setup Preparing network connection.

Panel Locked The User Lock function is engaged. The panel controls do not work.

Panel Unlocked The User Lock function has been disengaged. Panel operation is now possible.

Scene Recalling Scene recall in progress.

Scene Storing Scene store in progress. Do NOT turn power off while the unit displays this message.

Cannot Recall Recalling scenes or libraries is disabled.

Cannot Store The scene store is disabled.

NO X-OVER Input channels do not feature the X-Over parameter.

NO LIMITER Input channels do not feature the Limiter parameter.

Protected You cannot edit or delete protected scenes.

Panel Protected If the User Lock function is turned on, you cannot change the parameters by using the panel controls.

NO ROUTING Input channel SUM does not feature the Routing parameter.

NO LEVEL Input channel SUM does not feature the Level parameter.

Network Busy There is too much network trafﬁc. Communication is very slow.

Synchronizing Data is being received from the computer. Do NOT turn power off while the unit displays this message.

Scene Deleting Deleting a scene. Do NOT turn power off while the unit displays this message.

Symptom Possible Causes Possible Solutions

No communication between the

SP2060 and the DME Designer

application software.

The connection cable is not connected properly. Make sure that the cable is properly connected.

The computer's Ethernet port is not functioning

properly.

Refer to the DME Designer Installation Guide.

The DME-N Network driver has not been

installed.

Install and set up the DME-N Network driver.

No audio output.

The Mute function is turned on. Turn off the Mute function (see page 36).

The output level is set too low. Increase the output level (see page 23).

The parameters cannot be edited. The User Lock function is turned on. Turn off the User Lock function (see page 33).

References

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

General Specifications

Electrical Characteristics

Output impedance of signal generator: 150 Ω

Frequency Response

Total Harmonic Distortion

Hum & Noise

Dynamic Range

Sampling Frequency

External

Normal Rate: 44.1, 48 kHz (±0.1%)

Double Rate: 88.2, 96 kHz (±0.1%)

Internal 96 kHz

Signal Delay

Less than 761 µ sec (INPUT to OUTPUT @Fs=96kHz)

Indicators

Key indicators x 9

MUTE indicators (INPUT A/B, OUTPUT 1–6)

6-segment LED level meters (INPUT A/B, OUTPUT 1–6)

Miscellaneous

Power Consumption 30 W

Dimensions (HxDxW) 44 x 361 x 480 mm

Net Weight 4.2 kg

Temperature Range

Operating: 5 to 40 ˚C

Storage: –20 to 60 ˚C

Included Accessories AC power cord, Rubber feet x 4, Owner’s manual

Input Output RL Conditions MIN TYP MAX Units

INPUT A, B OUTPUT 1–6 600 Ω

Fs=96kHz@20Hz–40kHz, reference to

the nominal output level @1kHz

–1.0 0.0 +0.5 dB

Input Output RL Conditions MIN TYP MAX Units

INPUT A, B OUTPUT 1–6 600 Ω

Fs=96kHz, +4dBu@20Hz–40kHz 0.05 %

Fs=96kHz, +22dBu@1kHz 0.007 %

DIGITAL INPUT

AES/EBU

OUTPUT 1–6 600 Ω Fs=48kHz@1kHz, Input level: –1dBFS 0.015 %

* Total Harmonic Distortion is measured with a 18dB/octave ﬁlter @80kHz.

Input Output RL Conditions MIN TYP MAX Units

INPUT A, B OUTPUT 1–6 600 Ω Fs=96kHz, Rs=150 Ω –82 –79 dBu

DIGITAL INPUT

AES/EBU

OUTPUT 1–6 600 Ω Fs=48kHz, Input level: –∞dBFS –86 dBu

*Hum & Noise are measured with a 6dB/octave ﬁlter @12.7kHz; equivalent to a 20kHz ﬁlter with inﬁnite dB/octave

attenuation.

Input Output RL Conditions MIN TYP MAX Units

INPUT A, B OUTPUT 1–6 600 Ω Fs=96kHz 106 dB

DIGITAL INPUT

AES/EBU

OUTPUT 1–6 600 Ω Fs=48kHz 110 dB

*Dynamic range is measured with a 6dB/octave ﬁlter @12.7kHz; equivalent to a 20kHz ﬁlter with inﬁnite dB/octave

attenuation.

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

References

SP2060 Owner’s Manual

Crosstalk@1KHz Fs=96kHz

LED Level Meters

Input/Output Characteristics

Analog Input Characteristics

Analog Output Characteristics

Digital Input Characteristics

Input Output Conditions MIN TYP MAX Units

INPUT A OUTPUT 2, 4, 6

INPUT A assigned to OUTPUT 1, 3 or 5

INPUT B assigned to OUTPUT 2, 4 or 6

–80 dB

INPUT B OUTPUT 1, 3, 5

INPUT A assigned to OUTPUT 1, 3 or 5

INPUT B assigned to OUTPUT 2, 4 or 6

–80 dB

*Crosstalk is measured with a 18dB/octave ﬁlter @80kHz.

Metering points Conditions MIN TYP MAX Units

INPUT A, B

OVER red LED: On 0 dBFS

–6 amber LED: On –6 dBFS

–12 amber LED: On –12 dBFS

–18 amber LED: On –18 dBFS

–30 green LED: On –30 dBFS

–48 green LED: On –48 dBFS

OUTPUT 1–6

OVER red LED: On 0 dBFS

LIMIT amber LED: On LIMIT*

–6 green LED: On –6 dBFS

–12 green LED: On –12 dBFS

–18 green LED: On –18 dBFS

–40 green LED: On –40 dBFS

*The LED turns on when the internal limiter is activated.

Input Terminals Actual Load

Impedance

For Use With

Nominal

Input level Connector

Nominal Max. before clip

INPUT A, B 10 k Ω 600 Ω Lines +4 dBu (1.23 V) +24 dBu (12.28 V) XLR-3-31 type (balanced) *1

*1. XLR-3-31 type connectors with latches are balanced. (1=GND, 2=HOT, 3=COLD)

*2. In these speciﬁcations, 0 dBu is referenced to 0.775 Vrms.

*3. All AD converters are 24-bit linear, 64-times oversampling. (Fs=96kHz)

Output

Terminals

Actual Load

Impedance

For Use With

Nominal

Input level Connector

Nominal Max. before clip

OUTPUT 1–6 75 Ω 600 Ω Lines +4 dBu (1.23 V) +24 dBu (12.28 V) XLR-3-32 type (balanced) *1

*1. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)

*2. In these speciﬁcations, 0 dBu is referenced to 0.775 Vrms.

*3. All DA converters are 24-bit linear, 128-times oversampling (Fs=48kHz) or 64-times oversampling (Fs=96kHz).

Terminal Format Data length Level Connector

DIGITAL INPUT AES/EBU AES/EBU 24 bit RS422 XLR-3-31 type (balanced) *1 *2

*1. XLR-3-31 type connector with latch is balanced. (1=GND, 2=HOT, 3=COLD)

*2. Only Double Speed Format is supported at 96 kHz. Double Channel or Single Format is not supported.

References

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

Control I/O Characteristics

Connector Pin Assignment

[NETWORK] Connector (100Base-TX Ethernet, RJ-45)

Terminal Format Level Connector

Network IEEE 802.3 10Base-T/100Base-TX RJ-45

Pin Connection

1 TxD+

2 TxD-

3 RxD+

4 Unused

5 Unused

6 RxD-

7 Unused

8 Unused

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

References

SP2060 Owner’s Manual

Dimensions

* Specifications and descriptions in this owner's manual are for information purpose only. Yamaha Corp. reserves the right to

charge or modify products or specifications at any time without prior notice. Since specifications, equipment or options may

not be the same in every locale, please check with your Yamaha dealer.

European models

Purchaser/User Information specified in EN55103-1 and EN55103-2.

Inrush Current: 35A

Conforms to Environments: E1,E2,E3 and E4.

440

480

361

354

(4)

Rubber feet

are included in

the package.

Unit: mm

References

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

Index

[▲INC/YES]/[▼DEC/NO] Keys ........................................... 21

100Base-TX

............................................................................ 38

10Base-T

................................................................................. 38

2 x (2-way + Sub)

.................................................................... 10

2 x (2-way + Sub) Link

............................................................ 10

2 x 2-way + 2 x Aux

................................................................. 11

2 x 2-way + 2 x Aux Link

........................................................ 11

2 x 3-way

................................................................................. 12

2 x 3-way Link

........................................................................ 12

3 x 2-way

................................................................................... 9

3 x 2-way Link

.......................................................................... 9

4 way +2 x Aux

........................................................................ 13

5-way + Aux

............................................................................ 14

6-way

...................................................................................... 15

About a scene .......................................................................... 29

[AC IN] Connector

................................................................. 22

AdjustGc (Adjustable Gc)

....................................................... 28

[BACK/STORE] Key .............................................................. 21

Battery page

............................................................................ 35

Bessel

...................................................................................... 28

Butrwrth (Butterworth)

........................................................... 28

Changing a scene title ............................................................. 31

Changing the parameter values

................................................ 23

Checking the backup battery

................................................... 35

Components

............................................................................. 8

Configuration

.......................................................................8, 9

2 x (2-way + Sub)

............................................................ 10

2 x (2-way + Sub) Link

.................................................... 10

2 x 2-way + 2 x Aux

......................................................... 11

2 x 2-way + 2 x Aux Link

................................................ 11

2 x 3-way

......................................................................... 12

2 x 3-way Link

................................................................ 12

3 x 2-way

........................................................................... 9

3 x 2-way Link

.................................................................. 9

4 way +2 x Aux

................................................................ 13

5-way + Aux

.................................................................... 14

6-way

.............................................................................. 15

Multi Zone

..................................................................... 16

Connector Pin Assignment

...................................................... 48

[CURRENT BACKUP]

......................................................... 35

DELAY ................................................................................... 24

[DELAY] Key

.......................................................................... 21

Deleting a scene

...................................................................... 32

Device Group page

..................................................................37

[DIGITAL INPUT] Connector (AES/EBU)

...........................22

Dimensions

..............................................................................49

Display

....................................................................................21

Displaying the current library

..................................................28

Displaying the firmware version

...............................................35

Displaying the label

..................................................................34

Displaying word clock

..............................................................34

DME Designer

..........................................................................7

Electrical Characteristics ..........................................................46

EQ (Equalizer)

.........................................................................24

[EQ] Key

.................................................................................21

[FACTORY SETUP] ..............................................................35

Features

.....................................................................................8

Firmware Version

......................................................................7

Front Panel

..............................................................................21

General Specifications ..............................................................46

Ground Screw

..........................................................................22

H.SHELF(High Shelving) .......................................................24

HPF

.........................................................................................24

Initializing the SP2060 ............................................................35

INPUT A/B LINK

..................................................................32

INPUT A/B LINK page

..........................................................32

Input channel A

.......................................................................26

Input channel B

.......................................................................26

Input channel SUM

.................................................................26

[INPUT] Connectors

...............................................................22

Input EQ

.................................................................................24

Input routing

...........................................................................26

Input/Output Characteristics

...................................................47

IP address

.................................................................................37

IP Address page

........................................................................37

L.SHELF(Low Shelving) ..........................................................24

Label page

................................................................................34

Last Memory Resume page

......................................................33

LEVEL

....................................................................................23

[LEVEL] Key

...........................................................................21

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

References

SP2060 Owner’s Manual

LIBRARY ............................................................................... 28

Library

...................................................................................... 8

LIMITER

............................................................................... 29

Limiter

.................................................................................... 40

[LIMITER] Key

...................................................................... 21

Link Mode page

...................................................................... 38

Linkwitz (Linkwitz-Riley)

....................................................... 28

LPF

......................................................................................... 24

MAC Address page ................................................................. 39

Master

..................................................................................... 37

Master ID page

....................................................................... 38

Meters

..................................................................................... 21

Multi Zone

............................................................................. 16

Multiple SP2060

..................................................................... 19

Mute

....................................................................................... 36

[MUTE] Key

.......................................................................... 21

[NETWORK] Connector ....................................................... 22

Network Settings

.................................................................... 37

[NEXT/RECALL] Key

........................................................... 21

octet ........................................................................................ 37

[OUTPUT] Connectors

......................................................... 22

Output EQ

............................................................................. 25

Output routing

....................................................................... 26

Parameters ................................................................................ 8

PEQ

........................................................................................ 24

[POWER ON/OFF] Key

........................................................ 21

Preset area

............................................................................... 30

Preset Libraries

........................................................................ 40

preset parameters

....................................................................... 8

preset scene (read-only scene)

.................................................... 9

Protecting a scene

.................................................................... 31

Rear Panel ............................................................................... 22

Recalling a library

................................................................... 28

Recalling a scene

..................................................................... 30

ROUTING

............................................................................. 26

[ROUTING] Key

................................................................... 21

SCENE ................................................................................... 29

Scene

......................................................................................... 8

[SCENE] Key

......................................................................... 21

scene number

...........................................................................30

scene property

..........................................................................30

[SEL] Keys

...............................................................................21

Setting a Device Group

............................................................37

Setting Link Mode

...................................................................38

Setting the Crossover

...............................................................27

Setting the IP Address

..............................................................37

Setting the Last Memory Resume

............................................33

Setting the Master ID

..............................................................38

Slave

........................................................................................37

Speaker

....................................................................................17

Speaker processing

...................................................................17

Status messages

........................................................................45

Storing a scene

.........................................................................31

Subwoofer

................................................................................40

System Examples

.....................................................................17

Thru ........................................................................................28

Troubleshooting

......................................................................45

Turning the power on and off

....................................................7

User area ..................................................................................30

User Lock

................................................................................33

User Lock page

........................................................................33

user scene (readable and writable scene)

.....................................9

UTILITY

.................................................................................32

[UTILITY] Key

.......................................................................21

Version page ............................................................................35

Viewing the MAC Address

......................................................39

W. Clock page .........................................................................34

Warning and error messages

....................................................44

[WITHOUT LIB.]

..................................................................35

X-OVER (Crossover) ...............................................................27

[X-OVER] Key

........................................................................21

Zone processing .......................................................................18

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

MEMO

References

Introduction

to the SP2060

Foreword

The Controls

and Connectors

Network Settings Panel Operation

SP2060 Owner’s Manual

MEMO

SP2060 Owner’s Manual

Foreword

Network Settings ReferencesPanel Operation

Introduction

to the SP2060

The Controls

and Connectors

MEMO

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou

au distributeur le plus proche de vous ﬁgurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,

Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Av. Reboucas 2636-Pinheiros CEP: 05402-400

Sao Paulo-SP. Brasil

Tel: 011-3085-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Viamonte 1145 Piso2-B 1053,

Buenos Aires, Argentina

Tel: 1-4371-7021

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

GERMANY

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Central Europe GmbH,

Branch Switzerland

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Central Europe GmbH,

Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/SLOVAKIA/

HUNGARY/SLOVENIA

Yamaha Music Central Europe GmbH,

Branch Austria, CEE Department

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-602039025

POLAND

Yamaha Music Central Europe GmbH

Sp.z. o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland

Tel: 022-868-07-57

THE NETHERLANDS/

BELGIUM/LUXEMBOURG

Yamaha Music Central Europe GmbH,

Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha-Hazen Música, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1

Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 6A

DK-2730 Herlev, Denmark

Tel: 44 92 49 00

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1

N-1345 Østerås, Norway

Tel: 67 16 77 70

OTHER EUROPEAN COUNTRIES

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2313

TURKEY/CYPRUS

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LB21-128 Jebel Ali Freezone

P.O.Box 17328, Dubai, U.A.E.

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

25/F., United Plaza, 1468 Nanjing Road (West),

Jingan, Shanghai, China

Tel: 021-6247-2211

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong,

Youngdungpo-ku, Seoul, Korea

Tel: 02-3770-0660

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-78030900

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building

140 Paya Lebor Road, Singapore 409015

Tel: 747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

891/1 Siam Motors Building, 15-16 ﬂoor

Rama 1 road, Wangmai, Pathumwan

Bangkok 10330, Thailand

Tel: 02-215-2626

OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2313

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2441

PA13

WG50780 605IPDHx.x-02B0

This document is printed on chlorine free (ECF) paper with soy ink.

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Yamaha Pro Audio global web site:

http://www.yamahaproaudio.com/

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

Printed in Japan

Documenttranscriptie

Owner’s Manual EN Precautions for Using a Rack-mounted SP2060 If several SP2060 units (or an SP2060 unit together with other devices) are installed in a poorly-ventilated rack, the heat generated by each unit may raise the temperature inside the rack, preventing the SP2060 from performing as designed. When mounting SP2060 units in a rack, please leave one rack space vacant for every two units. You can attach a ventilation panel to this space or leave it open to prevent excessive heat build-up. If the temperature inside the rack is expected to rise above 40 degrees Celsius or 104 degrees Fahrenheit (or if the ambient temperature outside the rack is expected to rise above 30 degrees Celsius or 86 Fahrenheit), install a fan kit in the top row of the rack. The fan must provide airflow of 1.6 m3/min or more and static pressure of 5 mmH2O or more. Vorsichtsmaßnahmen für den Einsatz eines im Rack montierten SP2060 Wenn in einem schlecht belüfteten Rack mehrere SP2060Einheiten (oder eine SP2060-Einheit zusammen mit anderen Geräten) untergebracht sind, kann die von den Geräten erzeugte Wärme die Temperatur im Rack erhöhen, was die vorgesehene Leistung des SP2060 beeinträchtigt. Wenn Sie SP2060-Einheiten in einem Rack einbauen, lassen Sie bitte alle zwei Geräte einen RackPlatz frei. Sie können an diesem Platz eine Lüftungsverkleidung anbringen oder ihn offen lassen, um die Entwicklung übermäßiger Hitze zu verhindern. FR Si vous craignez que la température à l’intérieur du rack ne dépasse 40 degrés Celsius ou 104 degrés Fahrenheit (ou que la température ambiante à l’extérieur du rack ne dépasse 30 degrés Celsius ou 86 degrés Fahrenheit), installez un kit de ventilation sur la rangée supérieure du rack. Le ventilateur doit fournir un flux d’air de 1,6 m3/min ou plus et une pression statique de 5 mmH2O ou plus. Precauciones para utilizar una SP2060 de montaje en bastidor Si se instalan varias unidades SP2060 (o una unidad SP2060 con otros dispositivos) en un bastidor insuficientemente ventilado, el calor generado por cada unidad podría aumentar la temperatura en el interior del bastidor, impidiendo que la unidad SP2060 funcione de la manera prevista. Cuando monte unidades SP2060 en un bastidor, deje un espacio de bastidor libre por cada dos unidades. Puede instalar un panel de ventilación en este espacio, o bien dejarlo abierto para evitar la acumulación de un calor excesivo. DE Wenn zu erwarten ist, dass die Temperatur im Rack über 40 Grad Celsius oder 104 Grad Fahrenheit ansteigt (oder wenn die Umgebungstemperatur außerhalb des Racks über 30 Grad Celsius oder 86 Grad Fahrenheit ansteigt), installieren Sie eine Lüftereinheit im Rack. Der Lüfter muss einen Luftdurchsatz von mindestens 1,6 m3/Minute oder mehr haben und einen statischen Druck von 5 mmH2O erzeugen können. Précautions à prendre en cas d’utilisation d’un SP2060 monté en rack Si vous installez plusieurs SP2060 (ou un SP2060 et d’autres périphériques) dans un rack mal aéré, la chaleur générée par chaque unité risque d’augmenter la température à l’intérieur du rack et d’empêcher le SP2060 de fonctionner correctement. Lorsque vous montez des SP2060 en rack, laissez un espace libre équivalant à un rack entre deux unités. Vous pouvez recouvrir cet espace d’un panneau de ventilation ou le laisser ouvert pour éviter toute accumulation de chaleur excessive. EN ES Si se espera que la temperatura interior del bastidor supere los 40 grados Celsius (o que la temperatura ambiente fuera del bastidor supere los 30 grados Celsius), instale un kit de ventilación en la fila superior del bastidor. El ventilador debe proporcionar una corriente de aire de 1,6 m3/min o más y una presión de 5 mmH2O o más. Fan kit SP2060 SP2060 Ventilation panel SP2060 SP2060 U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2007 Yamaha Corporation Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 9 10 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 12 13 14 Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. (98-6500) This product contains a battery that contains perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate) FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Yamaha Corporation of America Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620 Telephone : 714-522-9011 Type of Equipment : SPEAKER PROCESSOR Model Name : SP2060 This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B) ADVARSEL! Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. (lithium caution) (FCC DoC) NEDERLAND / THE NETHERLANDS • Dit apparaat bevat een lithium batterij voor geheugen back-up. • This apparatus contains a lithium battery for memory back-up. • Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur afdankt of de volgende Yamaha Service Afdeiing: Yamaha Music Nederland Service Afdeiing Kanaalweg 18-G, 3526 KL UTRECHT Tel. 030-2828425 • For the removal of the battery at the moment of the disposal at the end of the service life please consult your retailer or Yamaha Service Center as follows: Yamaha Music Nederland Service Center Address : Kanaalweg 18-G, 3526 KL UTRECHT Tel : 030-2828425 • Gooi de batterij niet weg, maar lever hem in als KCA. • Do not throw away the battery. Instead, hand it in as small chemical waste. IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN-andYELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. (lithium disposal) • This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.(3 wires) PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device. • Do not expose the device to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings. • Use only the included power cord. If you intend to use the device in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer. • Never insert or remove an electric plug with wet hands. • Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. • If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the device, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. • Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock. If you notice any abnormality • If this device should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. Do not open • Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: • Do not place the device in an unstable position where it might accidentally fall over. Power supply/Power cord • Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Doing so may result in noise, both in the device itself and in the TV or radio next to it. • When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. Connections Location • Before moving the device, remove all connected cables. • When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. • Avoid setting all equalizer controls and faders to their maximum. Depending on the condition of the connected devices, doing so may cause feedback and may damage the speakers. • Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. (5)-4 4 SP2060 Owner’s Manual • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. • Be sure to connect to a properly grounded power source. A ground screw is provided on the rear panel of this device for maximum safety and shock prevention. If the mains outlet is not grounded, be sure to connect the ground screw to a confirmed ground point before plugging the device into the mains. Improper grounding can result in electrical shock. Maintenance • Remove the power plug from the AC outlet when cleaning the device. 4/2 Handling caution Backup battery • Do not use the device for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. • Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors. • This device has a built-in backup battery. When you unplug the power cord from the AC outlet, the current scene data is retained. However, the life of the backup battery is about five years. If the battery wears out, the current scene data will be lost. When the backup battery charge becomes low, the unit first displays “LOW BATTERY” then “CRITICAL BATTERY” when you turn on the power to the unit. (The Battery page of the Utility display also indicates first “Low Battery” then “No Battery” when the charge becomes low.) In this case, please have qualified Yamaha service personnel replace the backup battery. The rubber feet included in this package can be attached to the bottom of this device to prevent slippage when it is to be used on a slipper y surface. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. Always turn the power off when the device is not in use. The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualifi ed Yamaha service personnel about replacing defective components. • • • • The illustrations in this document are for instructional purposes, and may appear somewhat different from the actual equipment. CobraNet is a trademark of Cirrus Logic, Inc. Ethernet is a trademark of Xerox Corporation. All other trademarks are the property of their respective holders and are hereby acknowledged. (5)-4 5/2 SP2060 Owner’s Manual 5 Foreword Contents Foreword .......................................... 7 Introduction to the SP2060 Accessories (Please make sure the following items are included in the package.)................................................. About the Firmware Version ........................................... About DME Designer ..................................................... Precautions for Using a Rack-mounted SP2060 .............. Preparation...................................................................... 7 7 7 7 7 Connecting the AC power cord........................................... 7 Turning the power on and off ............................................. 7 Introduction to the SP2060 ..................... 8 The Controls and Connectors Features........................................................................... 8 Glossary for the SP2060 .................................................. 8 Configuration ................................................................. 9 Panel Operation 3 x 2-way ............................................................................ 9 3 x 2-way Link .................................................................... 9 2 x (2-way + Sub) .............................................................. 10 2 x (2-way + Sub) Link...................................................... 10 2 x 2-way + 2 x Aux .......................................................... 11 2 x 2-way + 2 x Aux Link .................................................. 11 2 x 3-way .......................................................................... 12 2 x 3-way Link .................................................................. 12 4 way +2 x Aux ................................................................. 13 5-way + Aux ...................................................................... 14 6-way ................................................................................ 15 Multi Zone ....................................................................... 16 System Examples........................................................... 17 Speaker processing ............................................................ 17 Zone processing ................................................................ 18 Multiple SP2060............................................................... 19 The Controls and Connectors.................. 21 Network Settings Front Panel ................................................................... 21 Rear Panel ..................................................................... 22 Panel Operation ................................. 23 Basic Operation............................................................. 23 Changing the parameter values.......................................... 23 References LEVEL.......................................................................... 23 DELAY ......................................................................... 24 EQ (Equalizer) .............................................................. 24 Input EQ .......................................................................... 24 Output EQ ....................................................................... 25 ROUTING................................................................... 26 Input routing .................................................................... 26 Output routing ................................................................. 26 X-OVER (Crossover) .................................................... 27 Setting the Crossover ........................................................ 27 LIBRARY...................................................................... 28 Displaying the current library............................................ 28 Recalling a library.............................................................. 28 6 SP2060 Owner’s Manual LIMITER...................................................................... 29 SCENE ......................................................................... 29 About a scene..................................................................... 29 Recalling a scene ................................................................ 30 Storing a scene ................................................................... 31 Changing a scene title ........................................................ 31 Protecting a scene .............................................................. 31 Deleting a scene ................................................................. 32 UTILITY ...................................................................... 32 INPUT A/B LINK ............................................................ 32 User Lock .......................................................................... 33 Setting the Last Memory Resume ...................................... 33 Displaying the label ........................................................... 34 Displaying word clock ....................................................... 34 Checking the backup battery.............................................. 35 Displaying the firmware version......................................... 35 Initializing the SP2060 ...................................................... 35 Mute ............................................................................. 36 Network Settings ................................ 37 Setting a Device Group ................................................. Setting the IP Address ................................................... Setting the Master ID.................................................... Setting Link Mode ........................................................ Viewing the MAC Address ............................................ 37 37 38 38 39 References ....................................... 40 About Preset Libraries ................................................... 40 File name ........................................................................... 40 Subwoofer.......................................................................... 40 Limiter............................................................................... 40 Libraries for 1-way speaker processors ................................ 41 Libraries for 2-way speaker processors ................................ 42 Libraries for 3-way speaker processors ................................ 43 Display Messages........................................................... 44 Warning and error messages............................................... 44 Status messages .................................................................. 45 Troubleshooting ............................................................ General Specifications ................................................... Electrical Characteristics ................................................ Input/Output Characteristics ........................................ Connector Pin Assignment............................................ Dimensions ................................................................... Index ............................................................................. 45 46 46 47 48 49 50 Foreword Foreword Thank you for purchasing the Yamaha SP2060 Speaker Processor. In order to take full advantage of the features and performance provided by the SP2060, we urge you to read this owner’s manual thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference. You can check the firmware version of your SP2060 in the UTILITY display (see page 28). You can also download the latest firmware from the following Yamaha website. http://www.yamahaproaudio.com/ First plug the female-connector end of the AC cord into the [AC IN] socket on the rear panel of the SP2060, then plug the male plug into an appropriate AC mains outlet. Be sure to use the voltage specified for the device. The required voltage is printed on the name plate of the device. Turning the power on and off About DME Designer CAUTION DME Designer software enables you to control the SP2060 or DME series system from a connected computer. The DME Designer version 2.0 or later features this function. You can download DME Designer from the following Yamaha website. http://www.yamahaproaudio.com/ Precautions for Using a Rack-mounted SP2060 To prevent the initial power-on surge from generating a large noise spike or damaging your speaker system, turn devices on in the following order: audio sources, mixer (such as M7CL), SP2060, and finally power amplifiers. Reverse this order when turning power off. 1. Press the [POWER] switch to turn the power on to the SP2060. The SP2060 displays a message. 2. Press the [POWER] switch again to turn off NOTE The SP2060 remembers the scene settings when you turn off the power. When you turn on the power to the SP2060, it will start up with the same scene settings. You can also set up the SP2060 so that at the startup it will recall the scene selected before you turned off the power to the device (See page 33). CAUTION Fan kit Introduction to the SP2060 SpeakerProcessor SP2060 the power. If you install the SP2060 along with other SP2060 units or other devices in a poorly ventilated rack, the ambient temperature inside the rack may rise, resulting in inefficient performance. Be sure to install the SP2060 in a well-ventilated rack and make sure that the heat will be ventilated efficiently. If the temperature inside the rack is expected to rise above 40 degrees Celsius or 104 degrees Fahrenheit (or if the ambient temperature outside the rack is expected to rise above 30 degrees Celsius or 86 Fahrenheit), install a fan kit in the top row of the rack. The fan must provide airflow of 1.6m3/min or more and static pressure of 5mmH2O or more. The Controls and Connectors About the Firmware Version CAUTION Be sure to turn all devices OFF before connecting AC mains power. Panel Operation SP2060 Owner’s Manual (this document) AC power cord Rubber feet x 4 Connecting the AC power cord Do NOT turn off the power to the SP2060 while the unit is displaying the message “DO NOT TURN OFF!” at the bottom of the display, for example, while it is storing the scene. Otherwise, a malfunction may occur. Network Settings • • • Preparation References Accessories (Please make sure the following items are included in the package.) SP2060 SP2060 SP2060 Owner’s Manual 7 Foreword Introduction to the SP2060 Features Introduction to the SP2060 The Yamaha SP2060 Speaker Processor employs state-of-the-art digital technology and supports 96kHz audio. The SP2060 features two channel analog input connectors, an AES/EBU connector, and six channel analog output connectors. Since it includes preset settings for fixed installation speakers (such as the Yamaha IF/IS series), the SP2060 enables you to take the best advantage of a variety of speakers from 1-way through 6-way speakers. You can also control the SP2060 remotely using DME Designer application software. Glossary for the SP2060 This section explains terminology specific to the SP2060. Components & Parameters The Controls and Connectors The individual audio modules (equalizers, delays, and speaker processors that feature various speaker adjustment functions) are called “components.” Various settings included with each component are called “preset parameters.” Changing the parameter values for components enables you to control the effects of the audio process. Configuration A “configuration” is a complete set of components for constructing an optimum audio system that supports the connected speakers. See page 9. Each configuration determines the audio function(s) of the corresponding SP2060 unit. All parameter sets included with each component in a configuration are called “preset parameters.” Panel Operation Scene A combination of all configuration and preset parameter combinations is called a “scene.” A scene can be recalled from the panel of each SP2060 or via DME Designer. See page 29. Scene Configuration Preset Parameter Scene 1 Example: Limiter • Attack • Threshold • Release Scene 2 Network Settings Scene 99 Component Library References 8 All parameter sets included with each speaker processor component optimized for the connected speakers are called “libraries.” A library can be recalled from the panel of each SP2060 or via DME Designer. You can also create a library using DME Designer, then store it in an SP2060. SP2060 Owner’s Manual Configuration The SP2060 features 12 configurations. You can select one that suits the combination and configuration of the connected speakers. A configuration is stored as part of each preset scene (read-only scene) in scene memory slots #1 through #12, and can be recalled along with the corresponding scene. You can also edit parameters of a configuration, then store them in a user scene (readable and writable scene). Connection between the output port and output connector on each component is specified and fixed for each configuration. No.1. No.2. No.3. No.4. [3x2way [3x2way L [2x(2way+Sub) [2x(2way+Sub)L ] ] ] ] No.5. No.6. No.7. No.8. [2x2way+2xAux [2x2way+2xAuxL [2x3way [2x3way L ] ] ] ] No.9. [4way+2xAux No.10. [5way+Aux No.11. [6way No.12. [Multi Zone ] ] ] ] Introduction to the SP2060 Foreword Introduction to the SP2060 Controls three channel 2-way speakers. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] LOW LOW [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] The Controls and Connectors 3 x 2-way HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] LOW X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] LOW LOW X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA Panel Operation LOW [OUTPUT 6] HIGH Speaker’s input connector OUTPUT 1 2-way speaker (1) LOW OUTPUT 2 2-way speaker (1) HIGH OUTPUT 3 2-way speaker (2) LOW OUTPUT 4 2-way speaker (2) HIGH OUTPUT 5 2-way speaker (3) LOW OUTPUT 6 2-way speaker (3) HIGH References Output connector Network Settings HIGH 3 x 2-way Link Controls three channel 2-way speakers. All parameters for each component such as the Crossover, Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked. SP2060 Owner’s Manual 9 Introduction to the SP2060 Foreword 2 x (2-way + Sub) Controls two channel 2-way speakers and subwoofers. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] SUB WOOFER LOW Introduction to the SP2060 [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] LOW LOW X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] HIGH HIGH LIMIT [Library Data] X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] SUB WOOFER HIGH LIMIT [Library Data] The Controls and Connectors Output Delay Panel Operation Network Settings Output Level Output Mute Limiter DA [OUTPUT 5] LOW X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] HIGH HIGH Output connector Speaker’s input connector OUTPUT 1 Subwoofer (1) OUTPUT 2 2-way speaker (1) LOW OUTPUT 3 2-way speaker (1) HIGH OUTPUT 4 Subwoofer (2) OUTPUT 5 2-way speaker (2) LOW OUTPUT 6 2-way speaker (2) HIGH 2 x (2-way + Sub) Link Controls two channel 2-way speakers and subwoofers. All parameters for each component such as the Crossover, Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked. References 10 Output 6BandEQ with APF LOW SP2060 Owner’s Manual Foreword Introduction to the SP2060 2 x 2-way + 2 x Aux Controls two channel 2-way speakers and two channel subspeakers. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] LOW [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] LOW Introduction to the SP2060 LOW LOW X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] SUB SPEAKER LOW LIMIT [Library Data] X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] SUB SPEAKER Output connector Speaker’s input connector OUTPUT 1 2-way speaker (1) LOW OUTPUT 2 2-way speaker (1) HIGH OUTPUT 3 2-way speaker (2) LOW OUTPUT 4 2-way speaker (2) HIGH OUTPUT 5 1-way subspeaker (1) OUTPUT 6 1-way subspeaker (2) Panel Operation HIGH The Controls and Connectors X-Over References Controls two channel 2-way speakers and two channel subspeakers. All parameters for each component such as the Crossover, Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked. Network Settings 2 x 2-way + 2 x Aux Link SP2060 Owner’s Manual 11 Introduction to the SP2060 Foreword 2 x 3-way Controls two channel 3-way speakers. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] LOW LOW Introduction to the SP2060 [DIGITAL IN] + Input 8BandEQ Input Delay Input 8BandEQ Input Delay LIMIT X-Over [INPUT B] AD Input Level Input Mute Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] MID MID LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] LOW LOW LIMIT X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] The Controls and Connectors MID MID LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] HIGH HIGH Panel Operation Output connector Speaker’s input connector OUTPUT 1 3-way speaker (1) LOW OUTPUT 2 3-way speaker (1) MID OUTPUT 3 3-way speaker (1) HIGH OUTPUT 4 3-way speaker (2) LOW OUTPUT 5 3-way speaker (2) MID OUTPUT 6 3-way speaker (2) HIGH 2 x 3-way Link Network Settings Controls two channel 3-way speakers. All parameters for each component such as the Crossover, Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked. References 12 SP2060 Owner’s Manual Foreword Introduction to the SP2060 4 way +2 x Aux Controls one channel 4-way speaker and two channel subspeakers. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] LOW [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] LOW-MID LOW-MID X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] HIGH-MID Introduction to the SP2060 LOW HIGH-MID LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] SUB SPEAKER LOW LIMIT [Library Data] X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] SUB SPEAKER OUTPUT 1 4-way speaker (1) LOW OUTPUT 2 4-way speaker (1) LOW-MID OUTPUT 3 4-way speaker (1) HIGH-MID OUTPUT 4 4-way speaker (1) HIGH OUTPUT 5 1-way subspeaker (1) OUTPUT 6 1-way subspeaker (2) Network Settings Speaker’s input connector References Output connector Panel Operation HIGH The Controls and Connectors X-Over SP2060 Owner’s Manual 13 Introduction to the SP2060 Foreword 5-way + Aux Controls one channel 5-way speaker and one channel subspeaker. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] SUB-LOW SUB-LOW Introduction to the SP2060 [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] LOW LOW LIMIT X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] LOW-MID LOW-MID LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] HIGH-MID HIGH-MID LIMIT The Controls and Connectors Output Delay Panel Operation Output Level Output Mute Limiter DA [OUTPUT 5] HIGH LIMIT [Library Data] X-Over Output Delay HIGH Output connector Speaker’s input connector OUTPUT 1 5-way speaker (1) SUB-LOW OUTPUT 2 5-way speaker (1) LOW OUTPUT 3 5-way speaker (1) LOW-MID OUTPUT 4 5-way speaker (1) HIGH-MID OUTPUT 5 5-way speaker (1) HIGH OUTPUT 6 1-way subspeaker (1) Network Settings References 14 Output 6BandEQ with APF HIGH SP2060 Owner’s Manual Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] SUB SPEAKER Foreword Introduction to the SP2060 6-way Controls one channel 6-way speaker. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] SUB-LOW [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] LOW LOW LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] LOW-MID Introduction to the SP2060 SUB-LOW LOW-MID X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] MID MID LIMIT Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] HIGH-MID LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] HIGH OUTPUT 1 6-way speaker (1) SUB-LOW OUTPUT 2 6-way speaker (1) LOW OUTPUT 3 6-way speaker (1) LOW-MID OUTPUT 4 6-way speaker (1) MID OUTPUT 5 6-way speaker (1) HIGH-MID OUTPUT 6 6-way speaker (1) HIGH Network Settings Speaker’s input connector References Output connector Panel Operation HIGH The Controls and Connectors Output Delay HIGH-MID SP2060 Owner’s Manual 15 Introduction to the SP2060 Foreword Multi Zone Outputs only the frequency components (by retrieving them from the input signals) that are suitable for the response characteristics of each speaker connected to each of six output connectors. LIMIT [Library Data] A SUM B Introduction to the SP2060 [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] HIGH LOW [DIGITAL IN] + Input 8BandEQ Input Delay LIMIT [Library Data] X-Over [INPUT B] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] HIGH HIGH LIMIT [Library Data] X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] HIGH LOW LIMIT [Library Data] X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] HIGH HIGH LIMIT [Library Data] The Controls and Connectors X-Over Panel Operation Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] HIGH LIMIT [Library Data] X-Over Output Delay HIGH Output connector Speaker’s input connector OUTPUT 1 1-way speaker (1) OUTPUT 2 1-way speaker (2) OUTPUT 3 1-way speaker (3) OUTPUT 4 1-way speaker (4) OUTPUT 5 1-way speaker (5) OUTPUT 6 1-way speaker (6) Network Settings References 16 Output Delay LOW SP2060 Owner’s Manual Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] HIGH Foreword Introduction to the SP2060 System Examples This diagram indicates an example of a stereo 3-way system. The AES/EBU input connector on the SP2060 enables you to connect it directly to the AES/EBU output on a digital mixer. The configuration presets include 3 x 2-way, 2 x 3-way, 4-way + 2 x Aux, 5-way + Aux, and 6-way. (See page 9.) The SP2060 Routing function enables you to select IN A, IN B, or IN SUM (A+B) as component input. In this way, you can create a stereo, mono, or stereo mono (full-range stereo plus mono subwoofer) system very easily. You can also adjust the parameters or recall a scene from the front panel of the SP2060 or from a computer connected via Ethernet. Introduction to the SP2060 Speaker processing M7CL SP2060 1 XP7000 2 3 4 5 XP7000 Subwoofer XP7000 Bi-amp 2way Subwoofer Main speaker L 6 XP7000 Bi-amp 2way Main speaker R Panel Operation Left/Right (AES/EBU) * also Analog input available Network Settings AES/EBU The Controls and Connectors Ethernet L IN A IN A+B R IN B OUT 1 Sub L OUT 2 Low L OUT 3 Hi L OUT 4 Sub R OUT 5 Low R OUT 6 Hi R References Routing SP2060 Owner’s Manual 17 Introduction to the SP2060 Foreword Zone processing Introduction to the SP2060 This example is a stereo 3-zone system in which the SP2060 is used as a signal distributor, rather than a crossover. Adjusting the routing will enable you to create a monaural 6-zone system. You can adjust EQ, Delay, and Level for each output. This system is suitable for a facility that requires sound zoning, such as stores, restaurants, hotels, conference facilities, and exhibition halls, or for delay speakers in an SR system. MG16/4 The Controls and Connectors A 1 2 B 3 SP2060 4 5 XP7000 XP7000 6 XP7000 Panel Operation Network Settings L R L ZONE A R L ZONE B ZONE C Routing References L OUT 1 ZONE 1L OUT 2 ZONE 1R OUT 3 ZONE 2L OUT 4 ZONE 2R OUT 5 ZONE 3L OUT 6 ZONE 3R IN A+B R 18 IN A SP2060 Owner’s Manual R IN B Multiple SP2060 This example is a system that uses CobraNet™ for long-distance digital transfer between the control room and amp room. Audio signals from Yamaha PM5D digital mixing console, talkback mic signal, chime source, etc. are input to the DME64N. The output destination and level settings are specified via the Routing function. Furthermore, you can process output signals (EQ, Limiter, etc.) by adding an EQ component. The output from the DME64N is converted to CobraNet™ signals via the MY16-C, then transferred via the Ethernet cable to the NHB32-C located in the amp room. In the amp room, this signal is converted to the AES/EBU digital signal via the NHB32-C, then input to the SP2060, which, in turn, processes the signal using the Crossover, EQ, Delay, and Limiter to suit each speaker. The SP2060 control signal is also transferred to the amp room via the Ethernet cable. (Yamaha recommends that you use Giga-bit switching hubs.) Control Room Introduction to the SP2060 Foreword Introduction to the SP2060 DME64N Cascade HOME UTILITY LEVEL MUTE CANCEL ENTER MY16-C Switching Hub Switching Hub Ethernet AES/EBU CobraNet Amp Room Switching Hub Switching Hub Panel Operation SCENE Specifying the destination and processing (such as EQ) for the output signal The Controls and Connectors Talkback mic PM5D NHB32-C NETWORK HUB AND BRIDGE CONDUCT 88 ERROR LOCK SP2060 1 2 3 4 XP7000 6 1 XP7000 2 3 4 XM4180 5 6 XH200 References XP7000 5 SP2060 Network Settings LINK Main L Main R Mono Sub Stair Step Under Balcony Lobby/ Dressing Room SP2060 Owner’s Manual 19 Introduction to the SP2060 Foreword Routing L IN A IN A+B Introduction to the SP2060 R Low L OUT 2 Hi L OUT 3 Low R OUT 4 Hi R OUT 5 Mono Sub IN B OUT 6 The Controls and Connectors Panel Operation Network Settings References 20 OUT 1 SP2060 Owner’s Manual Stair Step (Mono) Under Balcony IN A IN A+B Lobby/ Dressing Room OUT 1 Under Balcony 1 OUT 2 Under Balcony 2 OUT 3 Under Balcony 3 OUT 4 Under Balcony 4 OUT 5 Lobby OUT 6 Dressing Room IN B Foreword The Controls and Connectors Front Panel % ^ Introduction to the SP2060 7 YES STORE RECALL A NO 8 !9 @) # 1 Display Displays the parameters selected for editing and information about the currently-recalled scene. Remove the transparent protective film that was applied prior to shipment from the factory. 2 [BACK/STORE] Key Selects the previous parameter. In the Scene display, it stores a selected scene. 3 [▲INC/YES]/[▼DEC/NO] Keys Confirm Yes or No to the change of parameter values or confirmation messages. 4 [NEXT/RECALL] Key Selects the next parameter. In the Library List display or Scene display, it recalls a selected library or scene respectively. 5 [LEVEL] Key Displays the input/output level settings. When these settings are displayed, the key LED lights up. 6 [DELAY] Key Displays the signal delay time settings. When these settings are displayed, the key LED lights up. 7 [EQ] Key Displays the EQ settings. When these settings are displayed, the key LED lights up. 8 [ROUTING] Key Displays the selection of the [INPUT] connectors and Output channel signal sources. When these settings are displayed, the key LED lights up. B 1 2 3 4 5 6 $ 9 [X-OVER] Key Displays the Crossover settings or library recall options. When these settings are displayed, the key LED lights up. ) [LIMITER] Key Displays the Limiter settings. When these settings are displayed, the key LED lights up. The Controls and Connectors 6 ! [SCENE] Key Displays scene store or recall options, or scene edit options. When these settings are displayed, the key LED lights up. @ [UTILITY] Key Displays the SP2060 Utility function settings. When these settings are displayed, the key LED lights up. # [MUTE] Key Displays the Mute settings. When these settings are displayed, the key LED lights up. At this time, each [SEL] key LED indicates the corresponding channel’s Mute On or Off and the [SEL] keys enable you to turn Mute On or Off for the corresponding channels. Holding down the [MUTE] key for two seconds or longer will turn the User Lock function On or Off. $ [SEL] Keys Select the corresponding channels for editing. The [SEL] key LED for each selected channel lights up. Panel Operation 5 Network Settings 2 3 4 % Meters Display the channel level meters and the Limiter indicators for Output channels. ^ [POWER ON/OFF] Key Turns mains power to the SP2060 on and off. SP2060 Owner’s Manual References 1 21 The Controls and Connectors Foreword Rear Panel ( º ¡ OUTPUT DIGITAL INPUT Introduction to the SP2060 AES/EBU & The Controls and Connectors Panel Operation 6 5 4 3 2 1 * & Ground Screw For maximum safety be sure to securely connect the SP2060 ground screw to an earth connection. The supplied power cable has a three-prong plug that will ground the unit when plugged into an appropriately grounded three-prong type AC mains outlet. If the AC outlet is not grounded, be sure to ground the unit by using this ground screw. Correct grounding will effectively eliminate hum noise and interference. * [AC IN] Connector Connect to the AC mains using the supplied AC power cord. First connect the power cord to the SP2060, then insert the power cord plug into an AC outlet. ( [NETWORK] Connector This is a 100Base-TX/10Base-T Ethernet connector for connection to a computer or other device in the network. NOTE • Use a CAT5 STP (Shielded Twisted Pair) cable for this connection to prevent electromagnetic interference. Since the SP2060 supports Auto MDI/MDI-X, it will automatically detect whether the connected cable is of the straight type or crossover type, and will configure itself to create the optimal connection. Therefore, you can use either a straight or crossover cable. • The maximum length of a cable between a switching hub and the SP2060 is 100 meters. Due to the quality of cables and switching hub performance, however, proper operation at the maximum length cannot be guaranteed in some cases. º [DIGITAL INPUT] Connector (AES/EBU) Connect an output of an AES/EBU (digital signal) compatible device to this XLR-3-31 connector. ¡ [OUTPUT] Connectors These XLR-3-32 balanced connectors output six channel analog audio signals. Connect them to the inputs on amplifiers. Network Settings ™ [INPUT] Connectors These XLR-3-31 balanced connectors input two channel analog audio signals. References 22 ™ SP2060 Owner’s Manual Basic Operation Foreword Panel Operation This section describes the function of the panel keys and related displays. change. To change the delay time, first press the [DELAY] key to switch to the Delay display. Refer to “The Controls and Connectors” on page 21 for information on the relationship between the parameters and keys. Some parameters will prompt you to confirm the operation to reflect the change in the value. In this case, a confirmation icon will appear on the display. Press the [NEXT] key to move the cursor to the icon, then press the [YES] key. A message prompts you to confirm. Press the [YES] key to confirm the operation. LEVEL OUT 1 ON/OFF = ON 2. Select a channel for which you wish to change the delay time. In this example, press the OUTPUT 1 [SEL] key. 3. Press the [NEXT] key repeatedly until the parameter you wish to change appears on the screen. In this example, select the Time parameter. OUT 1 TIME = You can view and adjust the Input and Output channel levels. Parameter Range INPUT A/B/SUM –∞, –138.00 through +10.00dB OUTPUT 1-6 –∞, –138.00 through +10.00dB 1. Press the [LEVEL] key to select the Level display. IN A LEVEL =-138.00dB The Controls and Connectors 1. Display the parameter setting you wish to Cursor Panel Operation SCENE EDIT 01:FOH(Event A) You can adjust the parameter settings, such as EQ, according to the speaker response or the acoustic environment of a particular venue. This section explains how to change the delay time for Output channel 1 as an example. Introduction to the SP2060 Confirmation icon Changing the parameter values 2.67ms The corresponding channel is selected. The [SEL] key LED for the selected channel lights up. parameter value. The parameter value on the screen changes accordingly. [▲ INC] key [▼ DEC] key Press the [▲ INC] key. The value increases. Hold down the [▲ INC] key. The value continues to increase as long as you hold down the key. While holding down the [▲ INC] key, press the [▼ DEC] key. The value continues to increase at a rate more rapid than when you hold down the [▲ INC] key. Press the [▼ DEC] key. The value decreases. Hold down the [▼ DEC] key. The value continues to decrease as long as you down the key. While holding down the [▼ DEC] key, press the [▲ INC] key. The value continues to decrease at a rate more rapid than when you hold down the [▼ DEC] key. IN B LEVEL =-138.00dB 3. Press the [▲INC]/[▼DEC] keys to adjust the input or output level. IN B LEVEL =-138.00dB References 4. Press the [▲ INC]/[▼ DEC] keys to change the Network Settings 2. Press the [SEL] key for the target channel. NOTE When INPUT A/B LINK is turned On, the parameters for channels A and B are linked and set to the same value automatically. SP2060 Owner’s Manual 23 Panel Operation Foreword DELAY EQ (Equalizer) You can set the signal delay time on each input and output channel. Set the On/Off parameter to On to delay the signal, and Off to bypass the delay. An EQ boosts or cuts the level of specified frequency ranges. The SP2060’s internal EQ processes input and output signals. Introduction to the SP2060 Parameter Range INPUT A/B/SUM 0–1300.00msec OUTPUT 1-6 0–500.00msec NO T E Channel SUM is a new channel created by applying the Level and Mute settings to Input channel A and B respectively, then adding both channel values. Input EQ You can apply eight-band EQ to Input channels A, B, and SUM. Set the On/Off parameter to On to apply EQ to the signal, and Off to not process the signal. You can set the following parameters for each band. 1. Press the [DELAY] key to select the Delay The Controls and Connectors Range Function BYPASS ON/OFF Sets the bypass for each frequency range to On or Off. Q 16.0–0.1 Specifies the width of each frequency range. FREQ (Frequency) 20.0Hz–20.0kHz Specifies the center frequency of each frequency range. GAIN –18dB through +18.00dB Sets the gain of the target frequency. display. IN A ON/OFF = OFF 2. Press the [SEL] key for the target channel. Panel Operation The [SEL] key LED of the selected channel lights up, and the corresponding channel name is displayed. Pressing the [SEL] keys for Input channels A and B simultaneously will turn on the [SEL] key LEDs and select channel SUM. You can select a type of filter for band 1 and band 8. All other bands utilize a fixed parametric EQ. Parameter Range Function TYPE PEQ L.SHELF 6dB/Oct L.SHELF 12dB/Oct H.SHELF 6dB/Oct H.SHELF 12dB/Oct HPF LPF Selects a type of filter. IN SUM ON/OFF = OFF 3. Press the [▲INC]/[▼DEC] keys to select On or Network Settings Off. IN SUM ON/OFF = ON 4. Press the [DELAY] or [NEXT] key to display the Time parameter. References IN B TIME = 130.00ms 5. Press the [▲INC]/[▼DEC] keys to adjust the delay time. IN B TIME = 24 Parameter SP2060 Owner’s Manual • PEQ This is a standard parametric equalizer. • L.SHELF(Low Shelving) Does not cut the lower frequency range, but cuts starting from the vicinity of the cutoff frequency toward the higher range at a specific rate. “6dB/Oct” and “12dB/Oct” stand for the cut amount per octave. • H.SHELF(High Shelving) Does not cut the higher frequency range, but cuts starting from the vicinity of the cutoff frequency toward the lower range at a specific rate. “6dB/Oct” and “12dB/Oct” stand for the cut amount per octave. • HPF This is a high pass filter (Q=0.7). The low frequency range is mildly cut (12dB/Oct), creating a slow curve. 120.00ms • LPF This is a low pass filter (Q=0.7). The high frequency range is mildly cut (12dB/Oct), creating a slow curve. 2. Press the [SEL] key for the target channel. IN SUM ON/OFF = You can set the following parameters for each band. Parameter Range Function BYPASS ON/OFF Sets the bypass for each frequency range to On or Off. TYPE PEQ L.SHELF 6dB/Oct L.SHELF 12dB/Oct H.SHELF 6dB/Oct H.SHELF 12dB/Oct HPF LPF APF 1st APF 2nd Horn Selects a type of filter. Q 63.0–0.1 Specifies the width of each frequency range. FREQ (Frequency) 20.0Hz–20.0kHz Specifies the frequency of each band. GAIN –18dB through +18.00dB Sets the gain of the target frequency. ON 3. Press the [EQ], [BACK] or [NEXT] key to display the On/Off parameter. 4. Press the [▲INC] key to set the On/Off parameter to On to apply EQ to the signal. Press the [▼DEC] key to set the On/Off parameter to Off to not process the signal. 5. Press the [BACK] or [NEXT] key to select the Bypass, Type, Q, Freq, or Gain parameter. IN SUM BAND 2 Q = 0.125 6. Pressing the [EQ] key repeatedly will scroll the bands from 1 through 8. IN SUM BAND 3 Q = 0.125 7. Press the [▲INC]/[▼DEC] keys to select the value. • APF (All Pass Filter) This filter passes all ranges of frequency, but changes only the phase. It is used to align the phase in the crossover range. APF 1st rotates the phase by 0 through 180 degrees, and APF 2nd rotates the phase by 0 through 360 degrees. APF 2nd requires the Q setting. • Horn A horn speaker typically features a roll-off in the higher frequency component. Horn EQ corrects this characteristics. For this purpose, the gain is limited to 0dB or higher, and the frequency to 500Hz or higher. References The [SEL] key LED of the selected channel lights up, and the corresponding channel name is displayed. Pressing the [SEL] keys for channels A and B will turn on the [SEL] key LEDs and select channel SUM. Introduction to the SP2060 ON You can apply a 6-band EQ to Output channels 1–6. Set the On/Off parameter to On to apply EQ to the signal, and Off to not process the signal. The parameters are the same as for the input EQ. The Controls and Connectors IN A ON/OFF = Output EQ Panel Operation EQ display. Network Settings 1. Press the [EQ] key repeatedly to select the Foreword Panel Operation SP2060 Owner’s Manual 25 Panel Operation Foreword ROUTING Output routing Introduction to the SP2060 Input routing You can route Input channel A, B, and SUM signals to the Crossover input. You can select either analog or digital input signals. This selection links to the word clock master setting. You can also route the left channel of an input signal received at the [INPUT A] or [DIGITAL IN] connector to both Input channels A and B. The following three channels are available: • IN A • IN SUM • IN B Option Input Signal Selection ANA A/B A signal at the [INPUT A] connector is routed to channel A, and a signal at the [INPUT B] connector to channel B. The Controls and Connectors ANA A/A A signal at the [INPUT A] connector is routed to channels A and B. DIG L/R A left channel signal is routed to channel A, and a right channel signal to channel B. DIG L/L Word Clock Master Internal clock: 96kHz Routing display. OUT 2 SOURCE = IN A 2. Press the [SEL] key for the target Output Incoming AES/ EBU signal A left channel signal is routed to channels A and B. channel. The [SEL] key LED for the selected channel lights up. The [SEL] key LED for each channel that shares the same component flashes. The selected channel name appears on the display. Panel Operation OUT 4 SOURCE = IN A HINT You can check the word clock status on the Utility display. See page 34. 3. Press the [▲INC]/[▼DEC] keys to select an input source to be routed to the Crossover. 1. Press the [ROUTING] key to select the Routing display. Network Settings INPUT SELECT SOURCE = ANA A/B 2. Press the [▲INC]/[▼DEC] keys to select an input signal source. INPUT SELECT SOURCE = ANA A/A References 26 1. Press the [ROUTING] key to select the NO T E Signals are muted while they are switched between analog and digital to avoid noise. SP2060 Owner’s Manual OUT 4 SOURCE = IN SUM Function TYPE Thru 6dB/Oct 12dB/Oct AdjustGc 12dB/Oct Butrwrth 12dB/Oct Bessel 12dB/Oct Linkwitz 18dB/Oct AdjustGc 18dB/Oct Butrwrth 18dB/Oct Bessel 24dB/Oct AdjustGc 24dB/Oct Butrwrth 24dB/Oct Bessel 24dB/Oct Linkwitz 36dB/Oct AdjustGc 36dB/Oct Butrwrth 36dB/Oct Bessel 48dB/Oct AdjustGc 48dB/Oct Butrwrth 48dB/Oct Bessel 48dB/Oct Linkwitz Selects an attenuation amount per octave, and a type of filter. If you select “Thru,” no filter will be applied. FREQ (Frequency) 20.0Hz–20.0kHz Specifies the cutoff frequency of the high pass filter. Gc –6dB through +6dB You can set the gain for the cutoff frequency (Gc) when you select “AdjustGc (Adjustable Gc)” for the Type parameter. TYPE Thru 6dB/Oct 12dB/Oct AdjustGc 12dB/Oct Butrwrth 12dB/Oct Bessel 12dB/Oct Linkwitz 18dB/Oct AdjustGc 18dB/Oct Butrwrth 18dB/Oct Bessel 24dB/Oct AdjustGc 24dB/Oct Butrwrth 24dB/Oct Bessel 24dB/Oct Linkwitz 36dB/Oct AdjustGc 36dB/Oct Butrwrth 36dB/Oct Bessel 48dB/Oct AdjustGc 48dB/Oct Butrwrth 48dB/Oct Bessel 48dB/Oct Linkwitz Selects an attenuation amount per octave, and a type of filter. If you select “Thru,” no filter will be applied. FREQ (Frequency) 20.0Hz–20.0kHz Specifies the cutoff frequency of the low pass filter. –6dB through +6dB You can set the gain for the cutoff frequency (Gc) when you select “AdjustGc (Adjustable Gc)” for the Type parameter. Input signals can be divided into specified frequency ranges to suit speaker response characteristics prior to output. The number of division is determined to 1-way through 6way, depending on the selected component. Parameter LEVEL POLARITY Range Function –∞, –138.00 through +10.00dB Adjusts the level of the signal input to the Crossover. The same Level setting is used for the output channels of a component. NORMAL INVERTED The output signal phase for each frequency range is inverted. HPF HPF Refer to Step 4. LPF 1. Press the [X-OVER] key repeatedly until the XOver display appears on the screen. OUT 1 FREQ LPF = 20.0kHz 2. Press the [SEL] key for the target Output channel. The [SEL] key LED of the selected channel lights up, and the corresponding channel name is displayed. OUT 3 FREQ LPF = 20.0kHz 3. Press the [NEXT]/[BACK] keys to select a parameter to edit. OUT 3 LPF TYPE =24AdjustGc LPF Gc SP2060 Owner’s Manual Introduction to the SP2060 Range The Controls and Connectors Parameter Setting the Crossover Panel Operation parameter value. Network Settings 4. Press the [▲INC]/[▼DEC] keys to set the References X-OVER (Crossover) Foreword Panel Operation 27 Panel Operation Foreword NO T E LIBRARY • The type names are abbreviated on the SP2060 screen. For example, “24dB/Oct Bessel” is displayed as “24Bessel.” • Gc page is displayed if you select “Adjust Gc” for the Type parameter. Using libraries facilitates the recall of optimal speaker settings. Up to 60 libraries are available for each component via the DME Designer application. Introduction to the SP2060 • Thru No filter is applied. The original characteristics are kept with no attenuation for all frequency ranges. • AdjustGc (Adjustable Gc) Filters with an Adjustable Gc enable you to adjust the gain at the cutoff frequency in the range of –6dB through +6dB. With Gc set to –3dB, the filter is practically a Butterworth filter. And with Gc set to –6dB, the filter is practically a Linkwitz-Riley filter. The Controls and Connectors • Butrwrth (Butterworth) This filter is the most common type of filter. It has a flat pass band and a –3dB gain at the cutoff frequency. • Bessel This filter focuses on the phase characteristics. Although it has a more gradual roll-off than a Butterworth filter, it will pass a square wave without causing ringing. Panel Operation • Linkwitz (Linkwitz-Riley) This filter features the square of the second order. When the output signal from its LPF and HPF are combined, the gain over the entire range is +/–0dB. It has a flat pass band and a –6dB gain at the cutoff frequency. Displaying the current library Pressing the [X-OVER] key repeatedly will select the Current Library display, Library List display, or X-Over display, in this order. The title of the library most recently recalled for each component will be displayed. CURRENT LIBRARY IF2112/95 NOTE Libraries cannot be displayed or recalled for Input channels. If you press an Input channel [SEL] key, a message appears. Recalling a library Follow the steps below to recall a library: 1. Press the [X-OVER] key repeatedly until the Library List display appears on the screen. LIBRARY LIST IF2112/64 Network Settings 2. Press the [SEL] key of an Output channel for a component for which you wish to recall a library. 3. Press the [▲INC]/[▼DEC] keys to select a library. LIBRARY LIST IF2112/64 References 4. Press the [NEXT/RECALL] key. A confirmation message will appear. LIBRARY RECALL ARE YOU SURE? 28 SP2060 Owner’s Manual The library is recalled and the unit returns to the Library List display. 1. Press the [LIMITER] key to select the Limiter display. OUT 1 ON/OFF = LIBRARY LIST IF2112/95 To cancel the recall operation, press the [NO] key, instead of the [YES] key. The unit returns to the Library List display. ON 2. Press the [SEL] key for the target channel. The [SEL] key LED of the selected channel lights up, and the corresponding channel name is displayed. HIN T OUT 4 ON/OFF = You can use the library data for speaker processor components for DME64N/24N that you have created using DME Designer. Introduction to the SP2060 5. To confirm the selection, press the [YES] key. Foreword Panel Operation ON display the On/Off parameter. Range Function THRESHOLD –54 through 0dB Sets the threshold value. ATTACK FAST MID SLOW MANUAL (0– 120.0ms) Sets the attack time. RELEASE FAST MID SLOW MANUAL 44.1kHz: 6ms–46s, 48kHz: 5ms–42.3s, 88.2kHz: 3ms–23s, 96kHz: 3ms–21.1s Sets the release time. If you select Fast, Mid, or Slow, the unit automatically sets the optimum value based on the maximum wave length of audio input to the Limiter. NOT E • You can set the attack time only when “Manual” is selected for the Attack parameter. • You can set the release time only when “Manual” is selected for the Release parameter. parameter to On to apply the Limiter to the signal. Press the [▼DEC] key to set the On/ Off parameter to Off to cancel the Limiter. 5. Press the [NEXT]/[BACK] keys to select a parameter to edit. OUT 4 THRESHOLD= -54dB 6. Press the [▲INC]/[▼DEC] keys to set the parameter value. Panel Operation Parameter 4. Press the [▲INC] key to set the On/Off SCENE About a scene The SP2060 enables you to store various parameter settings as part of scene, and recall them via the front panel or remotely from DME Designer. You can store the following settings in a scene: • Configuration • Routing • Parameter sets of all components • Scene titles • Scene protection status • INPUT A/B LINK • The title of the library most recently recalled Network Settings You can set up the Output channel limiter. The Limiter precludes signal levels higher than a specified threshold to avoid speaker damage from excess output level. References LIMITER The Controls and Connectors 3. Press the [LIMITER], [BACK] or [NEXT] key to H INT You can protect a scene to forbid overwriting. SP2060 Owner’s Manual 29 Panel Operation Foreword Scenes are stored in the preset area and user area. Recalling a scene Preset area There is a preset scene for each of 12 configurations. These scenes are numbered 1 through 12. Each scene title has the same name as the corresponding configuration title. Introduction to the SP2060 No.1. [3x2way No.2. [3x2way L No.3. [2x(2way+Sub) No.4. [2x(2way+Sub)L No.5. [2x2way+2xAux No.6. [2x2way+2xAux L No.7. [2x3way No.8. [2x3way L No.9. [4way+2xAux No.10. [5way+Aux No.11. [6way No.12. [Multi Zone H INT You can also recall a scene using the DME Designer application. ] ] ] ] ] ] ] ] ] ] ] ] NOTE If recalling a scene has changed the configuration, audio output will be muted momentarily. 1. Press the [SCENE] key to select the Scene Selection display. The Controls and Connectors User area The user area can accommodate up to 87 user scenes, which you can store and recall at your discretion. These scenes are numbered 13 through 99. Scene indication Scene number Scene property Follow the steps below to recall a scene (1–99): Title 25:FOH(Event A) [2x(2way+SUB)L] 2. Press the [▲INC]/[▼DEC] keys to select a scene number. While you are selecting a scene, the scene number and title will be flashing. NOTE Panel Operation 25:FOH(Event A) [2x(2way+SUB)L] If no data is included in the currently-selected scene, the message “No Scene” appears. Configuration title The upper row indicates a scene number, property, and title. The bottom row indicates the configuration title. 3. Press the [RECALL] key. A confirmation message will appear. Scene property includes the following types: 33:RECALL ARE YOU SURE? Network Settings Preset scene Protected user scene 4. Press the [YES] key. Unprotected user scene NO T E After you recall a scene, if you edit a parameter, an appears in the lower right corner on the screen. References 30 icon The scene is recalled and its number becomes the current scene number. To cancel the recall operation, press the [NO] key, instead of the [YES] key. The unit returns to the Scene Selection display. NOTE If the selected scene contains no data or User Lock is turned on for the scene, a status message appears. SP2060 Owner’s Manual You can also store a scene using the DME Designer application. 1. Press the [SCENE] key to select the Scene Selection display. 25:FOH(Event A) [2x(2way+SUB)L] 2. Press the [▲INC]/[▼DEC] keys to select a scene number. 3. Press the [BACK/STORE] key. A confirmation message will appear. 72:STORE ARE YOU SURE? H INT Holding down the [▲INC]/[▼DEC] keys will increase the speed at which the characters scroll. 4. When you finish editing the title, press the [NEXT] key repeatedly to move the cursor to the icon, then press the [YES] key. A confirmation message will appear. SCENE EDIT ARE YOU SURE? 5. To confirm the edit, press the [YES] key. The title is changed and the unit returns to the Scene Edit display. Protecting a scene Follow the steps below to protect a scene: 1. Press the [SCENE] key repeatedly until the 4. Press the [YES] key. The scene is stored and its number becomes the current scene number. To cancel the store operation, press the [NO] key, instead of the [YES] key. The unit returns to the Scene Selection display. Introduction to the SP2060 HIN T character. The Controls and Connectors Follow the steps below to store a scene (13–99) to the user area: 3. Press the [▲INC]/[▼DEC] keys to change the Scene Edit display appears on the screen. SCENE EDIT 73:FOH(Event A) Panel Operation Storing a scene Foreword Panel Operation 2. Press the [▲INC]/[▼DEC] keys to select a the scene property icon. SCENE EDIT 73:FOH(Event A) NOT E You cannot change the title of any protected User scenes. 1. Press the [SCENE] key repeatedly until the Scene Edit display appears on the screen. SCENE EDIT 73:FOH(Event A) 4. Press the [▲INC]/[▼DEC] keys to turn protection on or off. The protection icon flashes. SCENE EDIT 73 FOH(Event A) References Follow the steps below to change the title (up to 13 characters) of the scene stored for the current scene number: 3. Press the [NEXT] key to move the cursor to Network Settings scene number. Changing a scene title 2. Press the [BACK]/[NEXT] keys to move the cursor to a character you want to edit. SCENE EDIT 73:FOH(Event A) SP2060 Owner’s Manual 31 Panel Operation Foreword 5. Press the [NEXT] key repeatedly to move the cursor to the icon, then press the [YES] key. A confirmation message will appear. SCENE EDIT ARE YOU SURE? Introduction to the SP2060 6. To confirm the edit, press the [YES] key. The unit reflects the edit and returns to the Scene Edit display. HINT You can turn protection on and off from the DME Designer application. UTILITY The Utility function enables you to view the word clock status and make network settings. See page 37 for more information on making network settings. INPUT A/B LINK Follow the steps below to link the Input channel A and B parameters: When INPUT A/B LINK is turned On, the parameters for channel A and B are linked and set to the same value automatically. NOTE The channel SUM parameters cannot be linked. The Controls and Connectors Follow the steps below to delete a scene: The following components will be linked: • INPUT LEVEL • INPUT EQ • INPUT DELAY 1. Press the [SCENE] key repeatedly until the 1. Press the [UTILITY] key to select the Utility Deleting a scene Scene Delete display appears on the screen. Panel Operation SCENE DELETE 72:FOH(Event A) display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the INPUT A/B LINK page appears. 2. Press the [▲INC]/[▼DEC] keys to select a scene to delete. INPUT A/B LINK OFF 3. Press the [NEXT] key to move the cursor to Network Settings the icon, then press the [YES] key. A confirmation message will appear. 3. Press the [▲INC] key to link the parameters. “ON” flashes on the screen. SCENE DELETE ARE YOU SURE? INPUT A/B LINK ON 4. To confirm the operation, press the [YES] key. The operation is executed and the unit returns to the Scene Delete display. 4. Press the [NEXT] key to move the cursor to the icon. References NO T E You cannot delete preset scenes, protected scenes, and current scene. INPUT A/B LINK ON 5. Press the [YES] key. A confirmation message will appear. INPUT A/B LINK ARE YOU SURE? 32 SP2060 Owner’s Manual The flashing “ON” (or “OFF”) lights up steadily, and the cursor returns to the “ON (or OFF)” position. 4. Press the [NEXT] key to move the cursor to the USER LOCK ON INPUT A/B LINK ARE YOU SURE? To cancel the operation and return to the original setting, press the [NO] key. icon. 5. Press the [YES] key. A confirmation message will appear. NOT E USER LOCK ARE YOU SURE? If you set INPUT A/B LINK to “ON,” the linked parameters for channel A will be copied to channel B parameters. Introduction to the SP2060 6. To confirm the operation, press the [YES] key. Foreword Panel Operation 6. To confirm the operation, press the [YES] key. User Lock NOT E H INT • A short cut to turn on the User Lock function is to hold down the [MUTE] key for two seconds or longer. • A short cut to turn off the User Lock function is to hold down the [MUTE] key for two seconds or longer. Setting the Last Memory Resume • You can mute or unmute, or cancel User Lock even if the User Lock function is turned on. • The User Lock function is effective only for the panel controls on the SP2060, and does not affect any control signals from external devices. 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the User Lock page appears. USER LOCK OFF 3. Press the [▲INC] key to turn User Lock on. To cancel User Lock, press the [▼DEC] key. “ON” flashes on the screen. You can select whether at the startup the SP2060 recalls the scene selected before you turned off the power to the device, or it starts up with the same status as when it was shut down last time. The default setting is “ON.” OFF: At the startup, the SP2060 will recall the scene selected before you turned off the power to the device. ON: The SP2060 will start up with the same status as when it was shut down last time. 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. Panel Operation Editing the parameters Recalling and storing a scene Changing a scene title Changing the scene protection status Recalling a library Network Settings * * * * * Panel Locked 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the Last Memory Resume page appears. LAST MEM. RESUME ON References Parameter settings can be “locked” temporarily to prevent accidental mis-operation. This function is useful to avoid unintentional operations or to prevent others from operating the panel controls. The following operations are the User Lock target. The Controls and Connectors A status message appears, and User Lock becomes active. USER LOCK ON SP2060 Owner’s Manual 33 Panel Operation Foreword 3. Press the [▲INC] key so that the SP2060 will start up with the same status as when it was shut down last time. Press the [▼DEC] key so that at the startup the SP2060 will recall the scene selected before you turned off the power to the device. “ON” flashes on the screen. Introduction to the SP2060 LAST MEM. RESUME ON 4. Press the [NEXT] key to move the cursor to the icon. The Controls and Connectors LAST MEM. RESUME ON 5. Press the [YES] key. A confirmation message will appear. Displaying word clock Word clock changes in accordance with input routing settings. You can view the current word clock status on the display. One of the following six word clock sources will be displayed: For analog input signals: The internal clock (Fs=96kHz) is used. • INT:96kHz : Internal clock (96kHz) For digital input signals: The SP2060 synchronizes to an external clock (input at the AES/EBU connector). • EXT:44.1kHz : External clock (44.1kHz) • EXT:48kHz : External clock (48kHz) • EXT:88.2kHz : External clock (88.2kHz) • EXT:96kHz : External clock (96kHz) • EXT:UNLOCK : Unlock to external clock 1. Press the [UTILITY] key to select the Utility LAST MEM. RESUME ARE YOU SURE? display. The most recently used Utility display page will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key Panel Operation 6. To confirm the operation, press the [YES] key. The selection is applied and the unit returns to the Last Memory Resume page. Displaying the label Network Settings 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the Label page appears. The unit displays the label you created on DME Designer. References LABEL [FoH L ] NO T E • You cannot edit the label on the SP2060. • Up to 14 characters from the top can be displayed. SP2060 Owner’s Manual W.CLOCK [INT: 96kHz] NOTE You can view the label for the SP2060 that you have set on DME Designer. 34 repeatedly until the W. Clock page appears. If no signal exists at the [DIGITAL INPUT] connector while digital input is selected, or if the SP2060 cannot somehow lock to the incoming signal, an error message appears. Checking the backup battery Initializing the SP2060 Follow the steps below to check the internal backup battery status: Follow the steps below to initialize the internal memory: You can select one of the following initialization types: 1. Press the [UTILITY] key to select the Utility * display. The most recently used Utility display will appear. * ] The remaining battery charge is displayed as follows: [OK ] Plenty of charge [Low Battery] Charge is getting low. [No Battery ] Memory data may be lost. Or, no battery is installed. CAUTION “Low Battery” or “No Battery” will appear when the battery charge is getting low. In this case, save the data to an external device (such as a computer) immediately, then ask the Yamaha dealer to replace the backup battery. CAUTION When the internal memory is initialized, all data stored in the memory will be lost. Use caution when you execute this function. 1. Turn off the power to the SP2060. 2. Turn on the power to the SP2060 while holding down the [BACK/STORE] key. The Initialization display appears. INITIALIZE FACTORY SETUP 3. Press the [▲INC]/[▼DEC] keys to select a type of initialization. HIN T Displaying the firmware version Follow the steps below to view the current firmware version number: 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display page will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the Version page appears. The page indicates the current firmware version number. NOTE To cancel the initialization operation, select “Exit” and confirm the cancellation. Alternatively, simply turn off the power to the SP2060. 4. Press the [NEXT] key to move the cursor to the icon, then press the [YES] key. The Initialization operation starts. During initialization, the following status message appears: INITIALIZE EXECUTING.. When initialization is completed, the SP2060 displays the following status message, then automatically restarts. References If there is any issue with the backup battery, the SP2060 displays “Low Battery,” “Critical Battery,” or “No Battery” when you turn on the power to the unit. INITIALIZE COMPLETED! VERSION The Controls and Connectors BATTERY [OK Panel Operation repeatedly until the Battery page appears. * Network Settings 2. Press the [UTILITY], [NEXT] or [BACK] key Initializing the current scene backup [CURRENT BACKUP] Initializing all user settings (excluding the libraries) to the factory settings [WITHOUT LIB.] Initializing all settings to the factory settings [FACTORY SETUP] Introduction to the SP2060 Foreword Panel Operation [V1.00] You can update the SP2060 firmware via DME Designer. Refer to the DME Designer Owner’s Manual for details. You can also download the latest firmware from the following Yamaha website. http://www.yamahaproaudio.com/ SP2060 Owner’s Manual 35 Panel Operation Foreword Mute When Mute is on, the corresponding Input or Output channel audio is muted. You can determine the channel Mute status by checking the corresponding channel [MUTE] key LED. Introduction to the SP2060 • • MUTE OFF : Dark MUTE ON : Illuminated 1. Press the [MUTE] key to select the Mute display. NOW SELECT KEYS ACT "MUTE" -> The Controls and Connectors 2. Press the [SEL] key for the target channel. The channel audio is muted and the [MUTE] key LED lights up. Pressing the channel [SEL] key repeatedly toggles between Mute on and off. A Panel Operation 1 NO T E You can mute or unmute even if the User Lock function is turned on Network Settings References 36 B SP2060 Owner’s Manual Setting the IP Address IP ADDRESS 192.168.000.003 When connecting a computer to an SP2060 via Ethernet, you must install the appropriate DME-N Network driver on the computer. You can download the DME-N Network driver from the Yamaha website. Network address Host address NOTE Setting a Device Group A “device group” is a group of multiple SP2060 units that can be operated in sync via DME Designer. Follow the steps below to assign each SP2060 in a device group as master or slave. Each device group must have one master. All other devices in the group are assigned as slave. 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the Device Group page appears. DEVICE GROUP MASTER • Subnet mask is fixed at 255.255.255.0. • Gateway address is the same network address as the IP address. The host address is automatically set to 254. Each group of digits between periods in an IP address is called “octet.” These groups of digits are called “1st octet,” “2nd octet,” etc., starting from the left-most digit group. You cannot specify 0, 127, and 223 through 255 for the 1st octet of the network address. You can specify the following range of values for the 4th octet. Master : 2–253 Slave : 3–253 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the IP Address page appears. The Controls and Connectors NOT E Introduction to the SP2060 Follow the steps below to set the IP address for each SP2060. Panel Operation This section describes the network-related settings on the SP2060 that you need to make when you connect a computer or other external device to the SP2060 [NETWORK] connector. Foreword Network Settings 3. Press the [▲INC]/[▼DEC] keys to select 4. Press the [NEXT] key to move the cursor to the icon, then press the [YES] key. A confirmation message will appear. DEVICE GROUP ARE YOU SURE? 3. Press the [NEXT]/[BACK] keys to move the cursor to an octet you want to specify. IP ADDRESS 192.168.000.003 4. Press the [▲INC]/[▼DEC] keys to change the value. When you change the value, the octet flashes. 5. Press the [NEXT] key to move the cursor to 5. To confirm the setting, press the [YES] key. The selection is applied and the unit returns to the Device Group page. Network Settings DEVICE GROUP SLAVE IP ADDRESS 192.168.000.002 References “MASTER” or “SLAVE.” When you change the setting, the parameter setting flashes. the icon, then press the [YES] key. A confirmation message will appear. IP ADDRESS ARE YOU SURE? SP2060 Owner’s Manual 37 Network Settings Foreword 6. To confirm the setting, press the [YES] key. The setting is applied and the unit returns to the IP Address page. Setting the Master ID Introduction to the SP2060 The SP2060 units that are assigned as slaves in a device group follow the master SP2060 in the same group via communication. Follow the steps below to set the master ID on the slave SP2060 units. Use the 4th octet of the IP address of the master unit as the Master ID parameter value. NO T E This parameter can be set from 2 through 253. The Controls and Connectors 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. Follow the steps below to select 100Base-TX or 10Base-T for the [NETWORK] connector speed. 100Base-TX The [NETWORK] connector basically operates as 100BaseTX, but automatically switches to 10Base-T if the network environment is not compatible with 100Base-TX. 10Base-T The [NETWORK] connector is compatible with 10Base-T operation. 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the Link Mode page appears. 2. Press the [UTILITY], [NEXT] or [BACK] key LINK MODE 100BASE-TX repeatedly until the Master ID page appears. MASTER ID 253 Panel Operation 3. Press the [▲INC]/[▼DEC] keys to set the value to the same number as the 4th octet of the master SP2060 IP address. 3. Press the [▲INC] key to select 100Base-TX, and the [▼DEC] key to select 10Base-T. When you change the setting, the parameter setting flashes. LINK MODE 10BASE-T 4. Press the [NEXT] key to move the cursor to the icon, then press the [YES] key. A confirmation message will appear. Network Settings MASTER ID ARE YOU SURE? 4. Press the [NEXT] key to move the cursor to the icon, then press the [YES] key. A confirmation message will appear. LINK MODE ARE YOU SURE? 5. To confirm the setting, press the [YES] key. The setting is applied and the unit returns to the Master ID page. To cancel the operation and return to the original setting, press the [NO] key, instead of the [YES] key. References 38 Setting Link Mode 5. To confirm the setting, press the [YES] key. The unit reflects the edit and returns to the Link Mode page. NOTE Depending on the specifications of the connected network devices (such as a switching hub, router, etc.), changing Link Mode may cause the SP2060 to be unable to reconnect to the network. In this case, turn the power to the SP2060 off and then on. The SP2060 will reconnect to the network. SP2060 Owner’s Manual Foreword Network Settings Viewing the MAC Address Follow the steps below to view the SP2060 MAC address: NOT E Introduction to the SP2060 In some cases, you may not need to set the MAC address via the DME-N Network driver when the SP2060 is communicating with DME Designer. 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key The Controls and Connectors repeatedly until the MAC Address page appears. The bottom row indicates the MAC address. References Network Settings Panel Operation MAC ADDRESS [00A0DE250123] SP2060 Owner’s Manual 39 Foreword References About Preset Libraries File name Introduction to the SP2060 LIBRARY LIST IF211264_pa_sub Model name The Controls and Connectors • • • • • Drive Subwoofer usage mode LIBRARY LIST IF2112AS_bi_moni Model name Drive Floor monitor mode pa........................ Passive mode* bi ........................ Bi-amp mode tri........................ Tri-amp mode sub...................... Combining with a subwoofer** moni ................... For a floor monitor * Yamaha Installation Series speakers are designed to be used without a speaker processor when Passive mode is selected. However, using a speaker processor will improve the performance significantly. ** This setting is for full-range speakers. Subwoofer settings are not included. Subwoofer • Panel Operation • • • “_sub” settings for 12-inch or 15-inch 3-way full-range speakers are designed for a combination with IS1118, IS1215, or IS1218. The IS1118, IS1215, and IS1218 settings are specified for a monaural subwoofer usage. The full-range and subwoofer level balance varies depending on the number of speakers used, installation conditions, and applications. If the full-range speaker baffle and subwoofer baffle are aligned, the speaker polarity will be positive and inphase. Depending on the installation conditions of the subwoofers, you might achieve better results if the subwoofer phase is inverted. Network Settings Limiter • • • The default value of the threshold level has been specified based on the maximum analog output level of +24dBu and amp voltage gain of 26dB (which corresponds to “ATT –6dB” if you are using a Yamaha PC series amplifier that features a voltage gain of 32dB). If you are not using the output levels referenced above, change the threshold level. For example, if you are using an amplifier with a voltage gain of 30dB, lower the threshold level by 4dB. Attack time and Release time are both set to “Mid.” The Limiter may not completely protect the speakers. Use the Limiter if they suit your environment. References 40 SP2060 Owner’s Manual Foreword References Libraries for 1-way speaker processors NO T E Target speakers Library name Meaning IS1118 and IS1218 IS1118_IS1218 This setting can be shared by IS1118 and IS1218 when IF2112 (M), IF2115 (M) or IF3115 is combined. IS1215 IS1215 This setting is for IS1215 when IF2112 (M), IF2115 (M) or IF3115 is combined. Standard subwoofer Sub_5inch&8inch This LPF setting can be shared by standard subwoofers when IF2205, IF2108, or IF2208 is combined. The following table shows the settings for Yamaha Installation Series speakers (full-range, passive mode). – – IF2205_sub ✓ – IF2108 – – IF2108_sub ✓ – IF2108_moni – ✓ IF2208 – – IF2208_sub ✓ – IF2208_moni – ✓ IF2112AS_pa – – IF2112/AS IF2112AS_pa_sub ✓ – IF2112AS_pa_moni – ✓ IF211264_pa – – IF211264_pa_sub ✓ – IF211295_pa – – IF211295_pa_sub ✓ – IF211299_pa – – IF211299_pa_sub ✓ – IF2112M64_pa – – IF2112M64_pa_sub ✓ – IF2112M95_pa – – IF2112M95_pa_sub ✓ – IF2112M99_pa – – IF2112M99_pa_sub ✓ – IF2115AS_pa – – IF2115AS_pa_sub ✓ – IF2115AS_pa_moni – ✓ IF211564_pa – – IF211564_pa ✓ – IF2112/64 IF2112/95 IF2112/99 IF2112M/64 IF2112M/95 IF2112M/99 IF2115/AS IF2115/64 Panel Operation IF2208 For a floor monitor IF2205 IF2205 IF2108 Subwoofer usage* Network Settings Library name References Target speakers The Controls and Connectors The following table shows typical subwoofer settings when it is combined with Yamaha Installation Series speakers. Introduction to the SP2060 These libraries also apply to 2-way speakers that are used in passive mode. SP2060 Owner’s Manual 41 References Foreword Target speakers Library name Subwoofer usage* For a floor monitor IF211595_pa – – IF211595_pa_sub ✓ – IF211599_pa – – IF211599_pa_sub ✓ – IF2115M64_pa – – IF2115M64_pa_sub ✓ – IF2115M95_pa – – IF2115M95_pa_sub ✓ – IF2115M99_pa – – IF2115M99_pa_sub ✓ – IF2115/95 IF2115/99 Introduction to the SP2060 IF2115M/64 IF2115M/95 IF2115M/99 * This setting is for full-range speakers. Subwoofer settings are not included. The Controls and Connectors Libraries for 2-way speaker processors N OT E These libraries also apply to 3-way speakers (including a combination of IL series and IH series speakers) that are used in biamp mode. Panel Operation The following table shows the settings for Yamaha Installation Series speakers (full-range, bi-amp mode). Target speakers IF2112/AS Library name – – IF2112AS_bi_sub ✓ – IF2112AS_bi_moni – ✓ IF211264_bi – – IF211264_bi_sub ✓ – IF211295_bi – – IF211295_bi_sub ✓ – IF211299_bi – – IF211299_bi_sub ✓ – IF2112M64_bi – – IF2112M64_bi_sub ✓ – IF2112M95_bi – – IF2112M95_bi_sub ✓ – IF2112M99_bi – – IF2112M99_bi_sub ✓ – IF2115AS_bi – – IF2115AS_bi_sub ✓ – IF2115AS_bi_moni – ✓ IF211564_bi – – IF211564_bi_sub ✓ – Network Settings IF2112/95 IF2112/99 IF2112M/64 IF2112M/95 References IF2112M/99 IF2115/64 42 SP2060 Owner’s Manual For a floor monitor IF2112AS_bi IF2112/64 IF2115/AS Subwoofer usage* Subwoofer usage* For a floor monitor IF211595_bi – – IF211595_bi_sub ✓ – IF211599_bi – – IF211599_bi_sub ✓ – IF2115M64_bi – – IF2115M64_bi_sub ✓ – IF2115M95_bi – – IF2115M95_bi_sub ✓ – IF2115M99_bi – – IF2115M99_bi_sub ✓ – IF311564_bi – – IF311564_bi_sub ✓ – IF311595_bi – – IF311595_bi_sub ✓ – IH2000/64 IH200064_bi – – IH2000/95 IH200095_bi – – IF2115/95 IF2115/99 IF2115M/64 IF2115M/95 IF2115M/99 IF3115/64 IF3115/95 Introduction to the SP2060 Library name The Controls and Connectors Target speakers Foreword References * This setting is for full-range speakers. Subwoofer settings are not included. Target speakers Library name Meaning IL1115 and IH2000/64 IL1115+IH64_pa Combination of IL1115 and IH2000/64 (passive mode) IL1116 and IH2000/95 IL1115+IH95_pa Combination of IL1115 and IH2000/95 (passive mode) Panel Operation The following table shows the settings for Yamaha Installation Series speaker IL series along with IH series. Target speakers Library name Subwoofer usage IF311564_tri – IF311564_tri_sub ✓ IF311595_tri – IF311595_tri_sub ✓ IF3115/64 IF3115/95 The following table shows the settings for Yamaha Installation Series speaker IL series along with IH series. Target speakers Library name Meaning IL1115 and IH2000/64 IL1115+IH64_bi Combination of IL1115 and IH2000/64 (bi-amp mode) IL1115 and IH2000/95 IL1115+IH95_bi Combination of IL1115 and IH2000/95 (bi-amp mode) SP2060 Owner’s Manual References The following table shows the settings for Yamaha Installation Series speakers (full-range, tri-amp mode). Network Settings Libraries for 3-way speaker processors 43 References Foreword Display Messages Warning and error messages Introduction to the SP2060 The Controls and Connectors Panel Operation Network Settings Message Meaning Action Duplicate IP Adr. Duplicate IP addresses. Change the IP addresses so that there are no duplicates. Illegal MAC Adr. An illegal MAC address has been encountered. This could be due to a hardware malfunction. Refer this problem to a contact a Yamaha dealer. Invalid IP Adr. The IP address is not set properly. Set an appropriate network IP address. Network Error A cable is disconnected, the power to the connected switching hub or router is turned off, or a cable is not in proper condition. Connect the cables properly, and make sure that the hub and/or router are operating correctly. No MAC Adr. MAC address not specified. This could be due to a hardware malfunction. Refer this problem to a Yamaha dealer. No Battery The internal battery is completely discharged or not installed. If you turn off the power to the unit, the current settings will be lost and reset to the default values. Stop operating the unit, and contact a Yamaha dealer for battery replacement. Critical Battery The internal battery is almost discharged. Your data may be lost. If you turn off the power to the unit, the current settings may be lost and reset to the default values. Stop operating the unit, and contact a Yamaha dealer for battery replacement. Low Battery The backup battery voltage is low. This does not affect the operation of the unit. However, if you continue using the unit, the settings may be lost and reset to the default values. Contact a Yamaha dealer for battery replacement at your earliest convenience. Recovering A program update attempt has failed, and the previous program is currently being restored. Do NOT turn power off while the unit is displaying this message. If the update attempt repeatedly fails, there may be a hardware malfunction. Refer this problem to a Yamaha dealer. Scene Recall Err A scene recall attempt has failed. Recall the scene again. If the problem persists, contact a Yamaha dealer. Saving Failed A save operation has failed. This could be due to a hardware malfunction. Refer this problem to a Yamaha dealer. Param Access Err Current setting cannot be displayed. Param Set Err Current setting cannot be changed. Save the current setting by using DME Designer, then initialize the unit. If the problem persists, contact a Yamaha dealer. W.Clk Unlocked A usable word clock signal is not being received or cannot be detected. Recheck all word clock connections and internal parameters. DevGrp Sync Err The device group configuration set via DME Designer does not match the real configuration. Use DME Designer to go off-line, create a configuration that correctly matches the actual configuration, and then go back on-line to synchronize the configuration. System Error A system error has occurred. Save the current setting by using DME Designer, then initialize the unit. If the problem persists, contact a Yamaha dealer. * Do NOT turn off the power to the SP2060 while the unit displays the message “DO NOT TURN OFF!” at the bottom of the display. References 44 SP2060 Owner’s Manual Status messages Meaning Connecting Connecting to the network. Download Success The program has been successfully updated. Downloading Program update in progress. Do NOT turn power off while the unit displays this message. File Operating A file operation is in progress during which the computer manipulates scene data. Do NOT turn power off while the unit displays this message. Network Setup Preparing network connection. Panel Locked The User Lock function is engaged. The panel controls do not work. Panel Unlocked The User Lock function has been disengaged. Panel operation is now possible. Scene Recalling Scene recall in progress. Scene Storing Scene store in progress. Do NOT turn power off while the unit displays this message. Cannot Recall Recalling scenes or libraries is disabled. Cannot Store The scene store is disabled. NO X-OVER Input channels do not feature the X-Over parameter. NO LIMITER Input channels do not feature the Limiter parameter. Protected You cannot edit or delete protected scenes. Panel Protected If the User Lock function is turned on, you cannot change the parameters by using the panel controls. NO ROUTING Input channel SUM does not feature the Routing parameter. NO LEVEL Input channel SUM does not feature the Level parameter. Network Busy There is too much network traffic. Communication is very slow. Synchronizing Data is being received from the computer. Do NOT turn power off while the unit displays this message. Scene Deleting Deleting a scene. Do NOT turn power off while the unit displays this message. * Do NOT turn off the power to the SP2060 while the unit displays the message “DO NOT TURN OFF!” at the bottom of the display. Panel Operation The Controls and Connectors Message Introduction to the SP2060 Foreword References Symptom No communication between the SP2060 and the DME Designer application software. Possible Causes Possible Solutions The connection cable is not connected properly. Make sure that the cable is properly connected. The computer's Ethernet port is not functioning properly. Refer to the DME Designer Installation Guide. The DME-N Network driver has not been installed. Install and set up the DME-N Network driver. The Mute function is turned on. Turn off the Mute function (see page 36). The output level is set too low. Increase the output level (see page 23). The User Lock function is turned on. Turn off the User Lock function (see page 33). Network Settings Troubleshooting The parameters cannot be edited. SP2060 Owner’s Manual References No audio output. 45 References Foreword General Specifications External Normal Rate: 44.1, 48 kHz (±0.1%) Double Rate: 88.2, 96 kHz (±0.1%) Internal 96 kHz Sampling Frequency Introduction to the SP2060 Signal Delay Less than 761 µ sec (INPUT to OUTPUT @Fs=96kHz) Indicators Key indicators x 9 MUTE indicators (INPUT A/B, OUTPUT 1–6) 6-segment LED level meters (INPUT A/B, OUTPUT 1–6) Miscellaneous Power Consumption 30 W Dimensions (HxDxW) 44 x 361 x 480 mm Net Weight 4.2 kg Temperature Range Operating: 5 to 40 ˚C Storage: –20 to 60 ˚C Included Accessories AC power cord, Rubber feet x 4, Owner’s manual The Controls and Connectors Electrical Characteristics Output impedance of signal generator: 150 Ω Frequency Response Input Panel Operation INPUT A, B Output OUTPUT 1–6 Conditions MIN TYP MAX Units 600 Ω Fs=96kHz@20Hz–40kHz, reference to the nominal output level @1kHz –1.0 0.0 +0.5 dB Conditions MIN TYP MAX Units Fs=96kHz, +4dBu@20Hz–40kHz 0.05 % Fs=96kHz, +22dBu@1kHz 0.007 % Fs=48kHz@1kHz, Input level: –1dBFS 0.015 % TYP MAX Units –79 dBu Total Harmonic Distortion Input Output RL INPUT A, B OUTPUT 1–6 600 Ω DIGITAL INPUT AES/EBU Network Settings RL OUTPUT 1–6 600 Ω * Total Harmonic Distortion is measured with a 18dB/octave filter @80kHz. Hum & Noise Input Output RL Conditions MIN INPUT A, B OUTPUT 1–6 600 Ω Fs=96kHz, Rs=150 Ω –82 DIGITAL INPUT AES/EBU OUTPUT 1–6 600 Ω Fs=48kHz, Input level: –∞dBFS –86 dBu *Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation. References Dynamic Range Input Output RL Conditions MIN TYP MAX INPUT A, B OUTPUT 1–6 600 Ω Fs=96kHz 106 dB DIGITAL INPUT AES/EBU OUTPUT 1–6 600 Ω Fs=48kHz 110 dB *Dynamic range is measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation. 46 SP2060 Owner’s Manual Units Crosstalk@1KHz Foreword References Fs=96kHz Input Output Conditions INPUT A OUTPUT 2, 4, 6 INPUT B OUTPUT 1, 3, 5 MIN TYP MAX Units INPUT A assigned to OUTPUT 1, 3 or 5 INPUT B assigned to OUTPUT 2, 4 or 6 –80 dB INPUT A assigned to OUTPUT 1, 3 or 5 INPUT B assigned to OUTPUT 2, 4 or 6 –80 dB Introduction to the SP2060 *Crosstalk is measured with a 18dB/octave filter @80kHz. LED Level Meters Metering points Conditions MIN TYP MAX Units OVER red LED: On 0 dBFS –6 amber LED: On –6 dBFS –12 amber LED: On –12 dBFS –18 amber LED: On –18 dBFS –30 green LED: On –30 dBFS –48 green LED: On –48 dBFS OVER red LED: On 0 dBFS LIMIT amber LED: On LIMIT* –6 green LED: On –6 dBFS –12 green LED: On –12 dBFS –18 green LED: On –18 dBFS –40 green LED: On –40 dBFS The Controls and Connectors INPUT A, B Panel Operation OUTPUT 1–6 *The LED turns on when the internal limiter is activated. Input/Output Characteristics Analog Input Characteristics INPUT A, B Actual Load Impedance For Use With Nominal 10 k Ω 600 Ω Lines Input level Nominal Connector Max. before clip +4 dBu (1.23 V) +24 dBu (12.28 V) XLR-3-31 type (balanced) *1 *1. XLR-3-31 type connectors with latches are balanced. (1=GND, 2=HOT, 3=COLD) *2. In these specifications, 0 dBu is referenced to 0.775 Vrms. *3. All AD converters are 24-bit linear, 64-times oversampling. (Fs=96kHz) Network Settings Input Terminals Analog Output Characteristics Actual Load Impedance For Use With Nominal OUTPUT 1–6 75 Ω 600 Ω Lines Input level Nominal Max. before clip +4 dBu (1.23 V) +24 dBu (12.28 V) Connector XLR-3-32 type (balanced) *1 *1. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD) *2. In these specifications, 0 dBu is referenced to 0.775 Vrms. *3. All DA converters are 24-bit linear, 128-times oversampling (Fs=48kHz) or 64-times oversampling (Fs=96kHz). References Output Terminals Digital Input Characteristics Terminal Format Data length Level Connector DIGITAL INPUT AES/EBU AES/EBU 24 bit RS422 XLR-3-31 type (balanced) *1 *2 *1. XLR-3-31 type connector with latch is balanced. (1=GND, 2=HOT, 3=COLD) *2. Only Double Speed Format is supported at 96 kHz. Double Channel or Single Format is not supported. SP2060 Owner’s Manual 47 References Foreword Control I/O Characteristics Terminal Format Level Connector Network IEEE 802.3 10Base-T/100Base-TX RJ-45 Introduction to the SP2060 Connector Pin Assignment [NETWORK] Connector (100Base-TX Ethernet, RJ-45) The Controls and Connectors Pin Connection 1 TxD+ 2 TxD- 3 RxD+ 4 Unused 5 Unused 6 RxD- 7 Unused 8 Unused Panel Operation Network Settings References 48 SP2060 Owner’s Manual Foreword References 480 Introduction to the SP2060 The Controls and Connectors 354 1 44 Rubber feet are included in the package. Panel Operation 440 3 361 (4) Dimensions * Specifications and descriptions in this owner's manual are for information purpose only. Yamaha Corp. reserves the right to charge or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. References European models Purchaser/User Information specified in EN55103-1 and EN55103-2. Inrush Current: 35A Conforms to Environments: E1,E2,E3 and E4. Network Settings Unit: mm SP2060 Owner’s Manual 49 References Foreword Index [▲INC/YES]/[▼DEC/NO] Keys ........................................... 21 Device Group page ..................................................................37 100Base-TX ............................................................................ 38 [DIGITAL INPUT] Connector (AES/EBU) ...........................22 Introduction to the SP2060 10Base-T ................................................................................. 38 Dimensions ..............................................................................49 2 x (2-way + Sub) .................................................................... 10 Display ....................................................................................21 2 x (2-way + Sub) Link ............................................................ 10 Displaying the current library ..................................................28 2 x 2-way + 2 x Aux ................................................................. 11 Displaying the firmware version ...............................................35 2 x 2-way + 2 x Aux Link ........................................................ 11 Displaying the label ..................................................................34 2 x 3-way ................................................................................. 12 Displaying word clock ..............................................................34 2 x 3-way Link ........................................................................ 12 DME Designer ..........................................................................7 3 x 2-way ................................................................................... 9 The Controls and Connectors 3 x 2-way Link .......................................................................... 9 E 4 way +2 x Aux ........................................................................ 13 Electrical Characteristics ..........................................................46 5-way + Aux ............................................................................ 14 EQ (Equalizer) .........................................................................24 6-way ...................................................................................... 15 [EQ] Key .................................................................................21 A F About a scene .......................................................................... 29 [FACTORY SETUP] ..............................................................35 [AC IN] Connector ................................................................. 22 Features .....................................................................................8 AdjustGc (Adjustable Gc) ....................................................... 28 Firmware Version ......................................................................7 Front Panel ..............................................................................21 B [BACK/STORE] Key .............................................................. 21 G Panel Operation Battery page ............................................................................ 35 General Specifications ..............................................................46 Bessel ...................................................................................... 28 Ground Screw ..........................................................................22 Butrwrth (Butterworth) ........................................................... 28 H C H.SHELF(High Shelving) .......................................................24 Changing a scene title ............................................................. 31 HPF .........................................................................................24 Changing the parameter values ................................................ 23 Checking the backup battery ................................................... 35 I Network Settings References Components ............................................................................. 8 Initializing the SP2060 ............................................................35 Configuration .......................................................................8, 9 2 x (2-way + Sub) ............................................................ 10 2 x (2-way + Sub) Link .................................................... 10 2 x 2-way + 2 x Aux ......................................................... 11 2 x 2-way + 2 x Aux Link ................................................ 11 2 x 3-way ......................................................................... 12 2 x 3-way Link ................................................................ 12 3 x 2-way ........................................................................... 9 3 x 2-way Link .................................................................. 9 4 way +2 x Aux ................................................................ 13 5-way + Aux .................................................................... 14 6-way .............................................................................. 15 Multi Zone ..................................................................... 16 INPUT A/B LINK ..................................................................32 Connector Pin Assignment ...................................................... 48 [CURRENT BACKUP] ......................................................... 35 INPUT A/B LINK page ..........................................................32 Input channel A .......................................................................26 Input channel B .......................................................................26 Input channel SUM .................................................................26 [INPUT] Connectors ...............................................................22 Input EQ .................................................................................24 Input routing ...........................................................................26 Input/Output Characteristics ...................................................47 IP address .................................................................................37 IP Address page ........................................................................37 L L.SHELF(Low Shelving) ..........................................................24 50 D Label page ................................................................................34 DELAY ................................................................................... 24 Last Memory Resume page ......................................................33 [DELAY] Key .......................................................................... 21 LEVEL ....................................................................................23 Deleting a scene ...................................................................... 32 [LEVEL] Key ...........................................................................21 SP2060 Owner’s Manual scene property ..........................................................................30 LIMITER ............................................................................... 29 [SEL] Keys ...............................................................................21 Limiter .................................................................................... 40 Setting a Device Group ............................................................37 [LIMITER] Key ...................................................................... 21 Setting Link Mode ...................................................................38 Link Mode page ...................................................................... 38 Setting the Crossover ...............................................................27 Linkwitz (Linkwitz-Riley) ....................................................... 28 Setting the IP Address ..............................................................37 LPF ......................................................................................... 24 Setting the Last Memory Resume ............................................33 Setting the Master ID ..............................................................38 M Slave ........................................................................................37 MAC Address page ................................................................. 39 Speaker ....................................................................................17 Master ..................................................................................... 37 Speaker processing ...................................................................17 Master ID page ....................................................................... 38 Status messages ........................................................................45 Meters ..................................................................................... 21 Storing a scene .........................................................................31 Multi Zone ............................................................................. 16 Subwoofer ................................................................................40 Multiple SP2060 ..................................................................... 19 System Examples .....................................................................17 Mute ....................................................................................... 36 [MUTE] Key .......................................................................... 21 T N Troubleshooting ......................................................................45 [NETWORK] Connector ....................................................... 22 Turning the power on and off ....................................................7 Thru ........................................................................................28 Introduction to the SP2060 scene number ...........................................................................30 The Controls and Connectors LIBRARY ............................................................................... 28 Library ...................................................................................... 8 Foreword References Network Settings .................................................................... 37 [NEXT/RECALL] Key ........................................................... 21 U User Lock page ........................................................................33 [OUTPUT] Connectors ......................................................... 22 user scene (readable and writable scene) .....................................9 Output EQ ............................................................................. 25 UTILITY .................................................................................32 Output routing ....................................................................... 26 [UTILITY] Key .......................................................................21 P V Parameters ................................................................................ 8 Version page ............................................................................35 PEQ ........................................................................................ 24 Viewing the MAC Address ......................................................39 [POWER ON/OFF] Key ........................................................ 21 Preset area ............................................................................... 30 W Preset Libraries ........................................................................ 40 W. Clock page .........................................................................34 preset parameters ....................................................................... 8 Warning and error messages ....................................................44 preset scene (read-only scene) .................................................... 9 [WITHOUT LIB.] ..................................................................35 Network Settings User Lock ................................................................................33 octet ........................................................................................ 37 Panel Operation User area ..................................................................................30 O Protecting a scene .................................................................... 31 X-OVER (Crossover) ...............................................................27 Rear Panel ............................................................................... 22 [X-OVER] Key ........................................................................21 Recalling a library ................................................................... 28 Recalling a scene ..................................................................... 30 Z ROUTING ............................................................................. 26 Zone processing .......................................................................18 References X R [ROUTING] Key ................................................................... 21 S SCENE ................................................................................... 29 Scene ......................................................................................... 8 [SCENE] Key ......................................................................... 21 SP2060 Owner’s Manual 51 Foreword Introduction to the SP2060 The Controls and Connectors Panel Operation Network Settings References SP2060 Owner’s Manual 52 MEMO References Network Settings Panel Operation The Controls and Connectors Introduction to the SP2060 Foreword MEMO SP2060 Owner’s Manual 53 Foreword Introduction to the SP2060 The Controls and Connectors Panel Operation Network Settings References SP2060 Owner’s Manual 54 MEMO For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México S.A. de C.V. Calz. Javier Rojo Gómez #1149, Col. Guadalupe del Moral C.P. 09300, México, D.F., México Tel: 55-5804-0600 BRAZIL Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. ASIA POLAND Yamaha Music Central Europe GmbH Sp.z. o.o. Oddzial w Polsce ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 THE NETHERLANDS/ BELGIUM/LUXEMBOURG Yamaha Music Central Europe GmbH, Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 FRANCE Yamaha Musique France BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 ITALY Yamaha Musica Italia S.P.A. Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 SPAIN/PORTUGAL Yamaha Musical do Brasil Ltda. Av. Reboucas 2636-Pinheiros CEP: 05402-400 Sao Paulo-SP. Brasil Tel: 011-3085-1377 ARGENTINA Yamaha-Hazen Música, S.A. Ctra. de la Coruna km. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 SWEDEN Yamaha Music Latin America, S.A. Sucursal de Argentina Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-4371-7021 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM Yamaha-Kemble Music (U.K.) Ltd. Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England Tel: 01908-366700 GERMANY Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 SWITZERLAND/LIECHTENSTEIN Yamaha Music Central Europe GmbH, Branch Switzerland Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: 01-383 3990 AUSTRIA Yamaha Music Central Europe GmbH, Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 CZECH REPUBLIC/SLOVAKIA/ HUNGARY/SLOVENIA Yamaha Music Central Europe GmbH, Branch Austria, CEE Department Schleiergasse 20, A-1100 Wien, Austria Tel: 01-602039025 Yamaha Scandinavia AB J. A. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. 25/F., United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 INDONESIA PT. Yamaha Music Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 KOREA Yamaha Music Korea Ltd. Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong, Youngdungpo-ku, Seoul, Korea Tel: 02-3770-0660 MALAYSIA Yamaha Music Malaysia, Sdn., Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 SINGAPORE Yamaha Music Asia Pte., Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 TAIWAN Yamaha KHS Music Co., Ltd. 3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C. Tel: 02-2511-8688 DENMARK YS Copenhagen Liaison Office Generatorvej 6A DK-2730 Herlev, Denmark Tel: 44 92 49 00 NORWAY Norsk filial av Yamaha Scandinavia AB Grini Næringspark 1 N-1345 Østerås, Norway Tel: 67 16 77 70 OTHER EUROPEAN COUNTRIES Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 AFRICA Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2313 MIDDLE EAST TURKEY/CYPRUS Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 THAILAND Siam Music Yamaha Co., Ltd. 891/1 Siam Motors Building, 15-16 floor Rama 1 road, Wangmai, Pathumwan Bangkok 10330, Thailand Tel: 02-215-2626 OTHER ASIAN COUNTRIES Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2317 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2313 OTHER COUNTRIES Yamaha Music Gulf FZE LB21-128 Jebel Ali Freezone P.O.Box 17328, Dubai, U.A.E. Tel: +971-4-881-5868 HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2441 PA13 Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ This document is printed on chlorine free (ECF) paper with soy ink. U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2006 Yamaha Corporation WG50780 605IPDHx.x-02B0 Printed in Japan