Owner’s Manual
EN
© 2007 Yamaha Corporation
U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
Precautions for Using a Rack-mounted SP2060
If several SP2060 units (or an SP2060 unit together with other
devices) are installed in a poorly-ventilated rack, the heat generated
by each unit may raise the temperature inside the rack, preventing
the SP2060 from performing as designed. When mounting SP2060
units in a rack, please leave one rack space vacant for every two
units. You can attach a ventilation panel to this space or leave it
open to prevent excessive heat build-up.
If the temperature inside the rack is expected to rise above 40
degrees Celsius or 104 degrees Fahrenheit (or if the ambient
temperature outside the rack is expected to rise above 30 degrees
Celsius or 86 Fahrenheit), install a fan kit in the top row of the rack.
The fan must provide airflow of 1.6 m
3
/min or more and static
pressure of 5 mmH
2
O or more.
Vorsichtsmaßnahmen für den Einsatz eines im Rack montierten SP2060
Wenn in einem schlecht belüfteten Rack mehrere SP2060-
Einheiten (oder eine SP2060-Einheit zusammen mit anderen
Geräten) untergebracht sind, kann die von den Geräten erzeugte
Wärme die Temperatur im Rack erhöhen, was die vorgesehene
Leistung des SP2060 beeinträchtigt. Wenn Sie SP2060-Einheiten in
einem Rack einbauen, lassen Sie bitte alle zwei Geräte einen Rack-
Platz frei. Sie können an diesem Platz eine Lüftungsverkleidung
anbringen oder ihn offen lassen, um die Entwicklung übermäßiger
Hitze zu verhindern.
Wenn zu erwarten ist, dass die Temperatur im Rack über 40 Grad
Celsius oder 104 Grad Fahrenheit ansteigt (oder wenn die
Umgebungstemperatur außerhalb des Racks über 30 Grad Celsius
oder 86 Grad Fahrenheit ansteigt), installieren Sie eine
Lüftereinheit im Rack. Der Lüfter muss einen Luftdurchsatz von
mindestens 1,6 m
3
/Minute oder mehr haben und einen statischen
Druck von 5 mmH
2
O erzeugen können.
Précautions à prendre en cas d’utilisation d’un SP2060 monté en rack
Si vous installez plusieurs SP2060 (ou un SP2060 et d’autres
périphériques) dans un rack mal aéré, la chaleur générée par
chaque unité risque d’augmenter la température à l’intérieur du
rack et d’empêcher le SP2060 de fonctionner correctement.
Lorsque vous montez des SP2060 en rack, laissez un espace libre
équivalant à un rack entre deux unités. Vous pouvez recouvrir cet
espace d’un panneau de ventilation ou le laisser ouvert pour éviter
toute accumulation de chaleur excessive.
Si vous craignez que la température à l’intérieur du rack ne dépasse
40 degrés Celsius ou 104 degrés Fahrenheit (ou que la température
ambiante à l’extérieur du rack ne dépasse 30 degrés Celsius ou 86
degrés Fahrenheit), installez un kit de ventilation sur la rangée
supérieure du rack. Le ventilateur doit fournir un flux d’air de
1,6 m
3
/min ou plus et une pression statique de 5 mmH
2
O ou plus.
Precauciones para utilizar una SP2060 de montaje en bastidor
Si se instalan varias unidades SP2060 (o una unidad SP2060 con
otros dispositivos) en un bastidor insuficientemente ventilado, el
calor generado por cada unidad podría aumentar la temperatura en
el interior del bastidor, impidiendo que la unidad SP2060 funcione
de la manera prevista. Cuando monte unidades SP2060 en un
bastidor, deje un espacio de bastidor libre por cada dos unidades.
Puede instalar un panel de ventilación en este espacio, o bien
dejarlo abierto para evitar la acumulación de un calor excesivo.
Si se espera que la temperatura interior del bastidor supere los 40
grados Celsius (o que la temperatura ambiente fuera del bastidor
supere los 30 grados Celsius), instale un kit de ventilación en la fila
superior del bastidor. El ventilador debe proporcionar una
corriente de aire de 1,6 m
3
/min o más y una presión de 5 mmH
2
O
o más.
Fan kit
Ventilation panel
SP2060
SP2060
SP2060
SP2060
EN
DE
FR
ES
The above warning is located on the top of the unit.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination
to avoid injury from tip-over.
13 Unplug this apparatus during
lightning storms or when unused for long periods of
time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
(98-6500)
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate)
This product contains a battery that contains perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions con-
tained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT:
When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reason-
able level of assurance that your use of this product in a residential
environment will not result in harmful interference with other elec-
tronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the users manual, may cause interference harmful to the operation
of other electronic devices. Compliance with FCC regulations does
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
not guarantee that interference will not occur in all installations. If
this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to elimi-
nate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please con-
tact Yamaha Corporation of America, Electronic Service Division,
6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
FCC INFORMATION (U.S.A.)
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif.
90620
Telephone : 714-522-9011
Type of Equipment : SPEAKER PROCESSOR
Model Name : SP2060
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including inter-
ference that may cause undesired operation.
See user manual instructions if interference to radio reception is
suspected.
(FCC DoC)
ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskift-
ning må kun ske med batteri af samme fabrikat og type. Levér det
brugte batteri tilbage til leverandoren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp
eller en ekvivalent typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda
paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä
käytetty paristo valmistajan ohjeiden mukaisesti.
(lithium caution)
NEDERLAND / THE NETHERLANDS
• Dit apparaat bevat een lithium batterij voor geheugen back-up.
• This apparatus contains a lithium battery for memory back-up.
• Raadpleeg uw leverancier over de verwijdering van de batterij op
het moment dat u het apparaat ann het einde van de levensduur
afdankt of de volgende Yamaha Service Afdeiing:
Yamaha Music Nederland Service Afdeiing
Kanaalweg 18-G, 3526 KL UTRECHT
Tel. 030-2828425
•For the removal of the battery at the moment of the disposal at the
end of the service life please consult your retailer or Yamaha Ser-
vice Center as follows:
Yamaha Music Nederland Service Center
Address : Kanaalweg 18-G, 3526 KL UTRECHT
Tel: 030-2828425
• Gooi de batterij niet weg, maar lever hem in als KCA.
• Do not throw away the battery. Instead, hand it in as small chemi-
cal waste.
(lithium disposal)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING:
THIS APPARATUS MUST BE EARTHED
IMPORTANT. The wires in this mains lead are coloured in accor-
dance with the following code:
GREEN-AND-YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals
in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be con-
nected to the terminal in the plug which is marked by the letter E or
by the safety earth symbol or colored GREEN or GREEN-and-
YELLOW.
The wire which is coloured BLUE must be connected to the termi-
nal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the ter-
minal which is marked with the letter L or coloured RED.
• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.(3 wires)
(5)-4
4/2
SP2060 Owner’s Manual
4
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
• Only use the voltage specified as correct for the device. The required voltage is
printed on the name plate of the device.
• Use only the included power cord.
If you intend to use the device in an area other than in the one you purchased,
the included power cord may not be compatible. Please check with your Yamaha
dealer.
• Do not place the power cord near heat sources such as heaters or radiators, and
do not excessively bend or otherwise damage the cord, place heavy objects on
it, or place it in a position where anyone could walk on, trip over, or roll anything
over it.
• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.
• Do not open the device or attempt to disassemble the internal parts or modify
them in any way. The device contains no user-serviceable parts. If it should
appear to be malfunctioning, discontinue use immediately and have it inspected
by qualified Yamaha service personnel.
• Do not expose the device to rain, use it near water or in damp or wet conditions,
or place containers on it containing liquids which might spill into any openings.
• Never insert or remove an electric plug with wet hands.
• If the power cord or plug becomes frayed or damaged, or if there is a sudden
loss of sound during use of the device, or if any unusual smells or smoke
should appear to be caused by it, immediately turn off the power switch,
disconnect the electric plug from the outlet, and have the device inspected by
qualified Yamaha service personnel.
• If this device should be dropped or damaged, immediately turn off the power
switch, disconnect the electric plug from the outlet, and have the device
inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the device or other property. These precautions include, but are not limited to, the following:
• Remove the electric plug from the outlet when the device is not to be used for
extended periods of time, or during electrical storms.
• When removing the electric plug from the device or an outlet, always hold the
plug itself and not the cord. Pulling by the cord can damage it.
• Before moving the device, remove all connected cables.
• When setting up the product, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn off
the power switch and disconnect the plug from the outlet. Even when the power
switch is turned off, electricity is still flowing to the product at the minimum
level. When you are not using the product for a long time, make sure to unplug
the power cord from the wall AC outlet.
•Avoid setting all equalizer controls and faders to their maximum. Depending on
the condition of the connected devices, doing so may cause feedback and may
damage the speakers.
• Do not expose the device to excessive dust or vibrations, or extreme cold or heat
(such as in direct sunlight, near a heater, or in a car during the day) to prevent
the possibility of panel disfiguration or damage to the internal components.
• Do not place the device in an unstable position where it might accidentally fall
over.
• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile
phone, or other electric devices. Doing so may result in noise, both in the device
itself and in the TV or radio next to it.
• Before connecting the device to other devices, turn off the power for all devices.
Before turning the power on or off for all devices, set all volume levels to
minimum.
• Be sure to connect to a properly grounded power source. A ground screw is
provided on the rear panel of this device for maximum safety and shock
prevention. If the mains outlet is not grounded, be sure to connect the ground
screw to a confirmed ground point before plugging the device into the mains.
Improper grounding can result in electrical shock.
• Remove the power plug from the AC outlet when cleaning the device.
Power supply/Power cord
Do not open
Water warning
If you notice any abnormality
Power supply/Power cord
Location
Connections
Maintenance
(5)-4
5/2
SP2060 Owner’s Manual
5
• Do not use the device for a long period of time at a high or uncomfortable
volume level, since this can cause permanent hearing loss. If you experience
any hearing loss or ringing in the ears, consult a physician.
• Do not rest your weight on the device or place heavy objects on it, and avoid use
excessive force on the buttons, switches or connectors.
• This device has a built-in backup battery. When you unplug the power cord from
the AC outlet, the current scene data is retained. However, the life of the backup
battery is about five years. If the battery wears out, the current scene data will be
lost. When the backup battery charge becomes low, the unit first displays “LOW
BATTERY” then “CRITICAL BATTERY” when you turn on the power to the unit.
(The Battery page of the Utility display also indicates first “Low Battery” then
“No Battery” when the charge becomes low.) In this case, please have qualified
Yamaha service personnel replace the backup battery.
The rubber feet included in this package can be attached to the bottom of this device to prevent slippage when it is to be used on a slippery surface.
Always turn the power off when the device is not in use.
The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualified Yamaha service
personnel about replacing defective components.
Handling caution Backup battery
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
• The illustrations in this document are for instructional purposes, and may appear somewhat different from the actual equipment.
• CobraNet is a trademark of Cirrus Logic, Inc.
• Ethernet is a trademark of Xerox Corporation.
• All other trademarks are the property of their respective holders and are hereby acknowledged.
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
6
Foreword .......................................... 7
Accessories (Please make sure the following items are
included in the package.)................................................. 7
About the Firmware Version ........................................... 7
About DME Designer..................................................... 7
Precautions for Using a Rack-mounted SP2060 .............. 7
Preparation...................................................................... 7
Connecting the AC power cord........................................... 7
Turning the power on and off ............................................. 7
Introduction to the SP2060 ..................... 8
Features........................................................................... 8
Glossary for the SP2060.................................................. 8
Configuration ................................................................. 9
3 x 2-way ............................................................................ 9
3 x 2-way Link .................................................................... 9
2 x (2-way + Sub).............................................................. 10
2 x (2-way + Sub) Link...................................................... 10
2 x 2-way + 2 x Aux .......................................................... 11
2 x 2-way + 2 x Aux Link .................................................. 11
2 x 3-way .......................................................................... 12
2 x 3-way Link .................................................................. 12
4 way +2 x Aux ................................................................. 13
5-way + Aux...................................................................... 14
6-way ................................................................................ 15
Multi Zone ....................................................................... 16
System Examples........................................................... 17
Speaker processing ............................................................ 17
Zone processing ................................................................ 18
Multiple SP2060............................................................... 19
The Controls and Connectors.................. 21
Front Panel ................................................................... 21
Rear Panel..................................................................... 22
Panel Operation ................................. 23
Basic Operation............................................................. 23
Changing the parameter values.......................................... 23
LEVEL.......................................................................... 23
DELAY ......................................................................... 24
EQ (Equalizer) .............................................................. 24
Input EQ .......................................................................... 24
Output EQ ....................................................................... 25
ROUTING................................................................... 26
Input routing .................................................................... 26
Output routing ................................................................. 26
X-OVER (Crossover) .................................................... 27
Setting the Crossover ........................................................ 27
LIBRARY...................................................................... 28
Displaying the current library............................................ 28
Recalling a library.............................................................. 28
LIMITER...................................................................... 29
SCENE ......................................................................... 29
About a scene..................................................................... 29
Recalling a scene ................................................................ 30
Storing a scene ................................................................... 31
Changing a scene title ........................................................ 31
Protecting a scene .............................................................. 31
Deleting a scene ................................................................. 32
UTILITY ...................................................................... 32
INPUT A/B LINK ............................................................ 32
User Lock .......................................................................... 33
Setting the Last Memory Resume ...................................... 33
Displaying the label ........................................................... 34
Displaying word clock ....................................................... 34
Checking the backup battery.............................................. 35
Displaying the firmware version......................................... 35
Initializing the SP2060 ...................................................... 35
Mute ............................................................................. 36
Network Settings ................................ 37
Setting a Device Group ................................................. 37
Setting the IP Address ................................................... 37
Setting the Master ID.................................................... 38
Setting Link Mode ........................................................ 38
Viewing the MAC Address ............................................ 39
References ....................................... 40
About Preset Libraries ................................................... 40
File name ........................................................................... 40
Subwoofer.......................................................................... 40
Limiter............................................................................... 40
Libraries for 1-way speaker processors ................................ 41
Libraries for 2-way speaker processors ................................ 42
Libraries for 3-way speaker processors ................................ 43
Display Messages........................................................... 44
Warning and error messages............................................... 44
Status messages .................................................................. 45
Troubleshooting............................................................ 45
General Specifications ................................................... 46
Electrical Characteristics................................................ 46
Input/Output Characteristics ........................................ 47
Connector Pin Assignment............................................ 48
Dimensions ................................................................... 49
Index ............................................................................. 50
Contents
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
SP2060 Owner’s Manual
7
Thank you for purchasing the Yamaha SP2060 Speaker Processor.
In order to take full advantage of the features and performance provided by the SP2060, we urge you to read this owner’s manual
thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference.
Accessories (Please make
sure the following items are
included in the package.)
• SP2060 Owner’s Manual (this document)
•AC power cord
•Rubber feet x 4
About the Firmware Version
You can check the firmware version of your SP2060 in the
UTILITY display (see page 28).
You can also download the latest firmware from the follow-
ing Yamaha website.
http://www.yamahaproaudio.com/
About DME Designer
DME Designer software enables you to control the SP2060
or DME series system from a connected computer.
The DME Designer version 2.0 or later features this func-
tion.
You can download DME Designer from the following
Yamaha website.
http://www.yamahaproaudio.com/
Precautions for Using a
Rack-mounted SP2060
If you install the SP2060 along with other SP2060 units or
other devices in a poorly ventilated rack, the ambient tem-
perature inside the rack may rise, resulting in inefficient per-
formance. Be sure to install the SP2060 in a well-ventilated
rack and make sure that the heat will be ventilated efficiently.
If the temperature inside the rack is expected to rise above 40
degrees Celsius or 104 degrees Fahrenheit (or if the ambient
temperature outside the rack is expected to rise above 30 de-
grees Celsius or 86 Fahrenheit), install a fan kit in the top
row of the rack. The fan must provide airflow of 1.6m
3
/min
or more and static pressure of 5mmH
2
O or more.
Preparation
Connecting the AC power cord
First plug the female-connector end of the AC cord into the
[AC IN] socket on the rear panel of the SP2060, then plug
the male plug into an appropriate AC mains outlet. Be sure
to use the voltage specified for the device. The required volt-
age is printed on the name plate of the device.
Turning the power on and off
1.
Press the [POWER] switch to turn the power
on to the SP2060.
The SP2060 displays a message.
2.
Press the [POWER] switch again to turn off
the power.
Foreword
Fan kit
SP2060
SP2060
Be sure to turn all devices OFF before connecting AC
mains power.
To prevent the initial power-on surge from generating a
large noise spike or damaging your speaker system, turn
devices on in the following order: audio sources, mixer
(such as M7CL), SP2060, and finally power amplifiers.
Reverse this order when turning power off.
NOTE
The SP2060 remembers the scene settings when you turn off the
power. When you turn on the power to the SP2060, it will start
up with the same scene settings.
You can also set up the SP2060 so that at the startup it will recall
the scene selected before you turned off the power to the device
(See page 33).
Do NOT turn off the power to the SP2060 while the unit
is displaying the message “DO NOT TURN OFF!” at the
bottom of the display, for example, while it is storing the
scene.
Otherwise, a malfunction may occur.
CAUTION
CAUTION
SpeakerProcessor
SP2060
CAUTION
SP2060 Owner’s Manual
Foreword
Introduction
to the SP2060
Network Settings ReferencesPanel Operation
The Controls
and Connectors
8
Features
The Yamaha SP2060 Speaker Processor employs state-of-the-art digital technology and supports 96kHz audio.
The SP2060 features two channel analog input connectors, an AES/EBU connector, and six channel analog out-
put connectors.
Since it includes preset settings for fixed installation speakers (such as the Yamaha IF/IS series), the SP2060 enables
you to take the best advantage of a variety of speakers from 1-way through 6-way speakers. You can also control
the SP2060 remotely using DME Designer application software.
Glossary for the SP2060
This section explains terminology specific to the SP2060.
Components & Parameters
The individual audio modules (equalizers, delays, and speaker processors that feature various speaker adjustment
functions) are called “components.” Various settings included with each component are called “preset parame-
ters.” Changing the parameter values for components enables you to control the effects of the audio process.
Configuration
A “configuration” is a complete set of components for constructing an optimum audio system that supports the
connected speakers. See page 9.
Each configuration determines the audio function(s) of the corresponding SP2060 unit. All parameter sets includ-
ed with each component in a configuration are called “preset parameters.”
Scene
A combination of all configuration and preset parameter combinations is called a “scene.” A scene can be recalled
from the panel of each SP2060 or via DME Designer. See page 29.
Library
All parameter sets included with each speaker processor component optimized for the connected speakers are
called “libraries.” A library can be recalled from the panel of each SP2060 or via DME Designer. You can also
create a library using DME Designer, then store it in an SP2060.
Introduction to the SP2060
Scene
Scene 1
Scene 2
Scene 99
Component
Configuration
Preset
Parameter
Example: Limiter
• Attack
• Threshold
• Release
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Introduction to the SP2060
SP2060 Owner’s Manual
9
Configuration
The SP2060 features 12 configurations. You can select one that suits the combination and configuration of the
connected speakers.
A configuration is stored as part of each preset scene (read-only scene) in scene memory slots #1 through #12, and
can be recalled along with the corresponding scene. You can also edit parameters of a configuration, then store
them in a user scene (readable and writable scene). Connection between the output port and output connector on
each component is specified and fixed for each configuration.
3 x 2-way
Controls three channel 2-way speakers.
3 x 2-way Link
Controls three channel 2-way speakers. All parameters for each component such as the Crossover, Delay, EQ, Lev-
el, and Limiter (excluding the Mute parameter) are linked.
No.1. [3x2way ] No.5. [2x2way+2xAux ] No.9. [4way+2xAux ]
No.2. [3x2way L ] No.6. [2x2way+2xAuxL ] No.10. [5way+Aux ]
No.3. [2x(2way+Sub) ] No.7. [2x3way ] No.11. [6way ]
No.4. [2x(2way+Sub)L ] No.8. [2x3way L ] No.12. [Multi Zone ]
Output connector
Speaker’s input connector
OUTPUT 1 2-way speaker (1) LOW
OUTPUT 2 2-way speaker (1) HIGH
OUTPUT 3 2-way speaker (2) LOW
OUTPUT 4 2-way speaker (2) HIGH
OUTPUT 5 2-way speaker (3) LOW
OUTPUT 6 2-way speaker (3) HIGH
[INPUT B]
[INPUT A]
[DIGITAL IN]
AD
AD
Input
Level
Input
Level
Input
Mute
Input
8BandEQ
Input
8BandEQ
Input
Delay
Input
Delay
Input
Mute
BA SUM
+
Input
8BandEQ
Input
Delay
[Library Data]
[Library Data]
[Library Data]
[OUTPUT 2]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
HIGH
[OUTPUT 6]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
HIGH
[OUTPUT 4]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
HIGH
[OUTPUT 1]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
LOW
[OUTPUT 5]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
LOW
[OUTPUT 3]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
LOW
Introduction to the SP2060
SP2060 Owner’s Manual
Foreword
Introduction
to the SP2060
Network Settings ReferencesPanel Operation
The Controls
and Connectors
10
2 x (2-way + Sub)
Controls two channel 2-way speakers and subwoofers.
2 x (2-way + Sub) Link
Controls two channel 2-way speakers and subwoofers. All parameters for each component such as the Crossover,
Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked.
Output connector Speaker’s input connector
OUTPUT 1 Subwoofer (1)
OUTPUT 2 2-way speaker (1) LOW
OUTPUT 3 2-way speaker (1) HIGH
OUTPUT 4 Subwoofer (2)
OUTPUT 5 2-way speaker (2) LOW
OUTPUT 6 2-way speaker (2) HIGH
+
[INPUT B]
[INPUT A]
[DIGITAL IN]
AD
AD
Input
Level
Input
Level
Input
Mute
Input
8BandEQ
Input
8BandEQ
Input
Delay
Input
Delay
Input
Mute
Input
8BandEQ
Input
Delay
BA SUM
[OUTPUT 1]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
SUB WOOFER
[OUTPUT 6]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 5]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
[OUTPUT 4]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
SUB WOOFER
[OUTPUT 3]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 2]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
[Library Data]
[Library Data]
[Library Data]
[Library Data]
LOW
HIGH
HIGH
LOW
LOW
HIGH
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Introduction to the SP2060
SP2060 Owner’s Manual
11
2 x 2-way + 2 x Aux
Controls two channel 2-way speakers and two channel subspeakers.
2 x 2-way + 2 x Aux Link
Controls two channel 2-way speakers and two channel subspeakers. All parameters for each component such as
the Crossover, Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked.
Output connector Speaker’s input connector
OUTPUT 1 2-way speaker (1) LOW
OUTPUT 2 2-way speaker (1) HIGH
OUTPUT 3 2-way speaker (2) LOW
OUTPUT 4 2-way speaker (2) HIGH
OUTPUT 5 1-way subspeaker (1)
OUTPUT 6 1-way subspeaker (2)
+
[INPUT B]
[INPUT A]
[DIGITAL IN]
AD
AD
Input
Level
Input
Level
Input
Mute
Input
8BandEQ
Input
8BandEQ
Input
Delay
Input
Delay
Input
Mute
Input
8BandEQ
Input
Delay
BA SUM
[OUTPUT 6]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
SUB SPEAKER
[OUTPUT 5]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
SUB SPEAKER
[OUTPUT 4]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 3]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
[OUTPUT 2]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[Library Data]
[Library Data]
[Library Data]
[Library Data]
HIGH
HIGH
HIGH
LOW
LOW
LOW
[OUTPUT 1]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
Introduction to the SP2060
SP2060 Owner’s Manual
Foreword
Introduction
to the SP2060
Network Settings ReferencesPanel Operation
The Controls
and Connectors
12
2 x 3-way
Controls two channel 3-way speakers.
2 x 3-way Link
Controls two channel 3-way speakers. All parameters for each component such as the Crossover, Delay, EQ, Level,
and Limiter (excluding the Mute parameter) are linked.
Output connector Speaker’s input connector
OUTPUT 1 3-way speaker (1) LOW
OUTPUT 2 3-way speaker (1) MID
OUTPUT 3 3-way speaker (1) HIGH
OUTPUT 4 3-way speaker (2) LOW
OUTPUT 5 3-way speaker (2) MID
OUTPUT 6 3-way speaker (2) HIGH
+
[INPUT B]
[INPUT A]
[DIGITAL IN]
AD
AD
Input
Level
Input
Level
Input
Mute
Input
8BandEQ
Input
8BandEQ
Input
Delay
Input
Delay
Input
Mute
Input
8BandEQ
Input
Delay
BA SUM
[OUTPUT 6]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 5]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
MID
[OUTPUT 3]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 2]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
MID
[Library Data]
[Library Data]
MID
HIGH
LOW
LOW
MID
HIGH
[OUTPUT 1]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
[OUTPUT 4]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Introduction to the SP2060
SP2060 Owner’s Manual
13
4 way +2 x Aux
Controls one channel 4-way speaker and two channel subspeakers.
Output connector Speaker’s input connector
OUTPUT 1 4-way speaker (1) LOW
OUTPUT 2 4-way speaker (1) LOW-MID
OUTPUT 3 4-way speaker (1) HIGH-MID
OUTPUT 4 4-way speaker (1) HIGH
OUTPUT 5 1-way subspeaker (1)
OUTPUT 6 1-way subspeaker (2)
+
[INPUT B]
[INPUT A]
[DIGITAL IN]
AD
AD
Input
Level
Input
Level
Input
Mute
Input
8BandEQ
Input
8BandEQ
Input
Delay
Input
Delay
Input
Mute
Input
8BandEQ
Input
Delay
BA SUM
[OUTPUT 6]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
SUB SPEAKER
[OUTPUT 5]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
SUB SPEAKER
[OUTPUT 4]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 3]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH-MID
[OUTPUT 2]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW-MID
[Library Data]
[Library Data]
[Library Data]
LOW-MID
HIGH
HIGH
LOW
LOW
HIGH-MID
[OUTPUT 1]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
Introduction to the SP2060
SP2060 Owner’s Manual
Foreword
Introduction
to the SP2060
Network Settings ReferencesPanel Operation
The Controls
and Connectors
14
5-way + Aux
Controls one channel 5-way speaker and one channel subspeaker.
Output connector Speaker’s input connector
OUTPUT 1 5-way speaker (1) SUB-LOW
OUTPUT 2 5-way speaker (1) LOW
OUTPUT 3 5-way speaker (1) LOW-MID
OUTPUT 4 5-way speaker (1) HIGH-MID
OUTPUT 5 5-way speaker (1) HIGH
OUTPUT 6 1-way subspeaker (1)
+
[INPUT B]
[INPUT A]
[DIGITAL IN]
AD
AD
Input
Level
Input
Level
Input
Mute
Input
8BandEQ
Input
8BandEQ
Input
Delay
Input
Delay
Input
Mute
Input
8BandEQ
Input
Delay
BA SUM
[OUTPUT 6]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
SUB SPEAKER
[OUTPUT 5]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 4]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH-MID
[OUTPUT 3]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW-MID
[OUTPUT 2]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
[Library Data]
[Library Data]
LOW
HIGH
HIGH-MID
SUB-LOW
HIGH
LOW-MID
[OUTPUT 1]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
SUB-LOW
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Introduction to the SP2060
SP2060 Owner’s Manual
15
6-way
Controls one channel 6-way speaker.
Output connector Speaker’s input connector
OUTPUT 1 6-way speaker (1) SUB-LOW
OUTPUT 2 6-way speaker (1) LOW
OUTPUT 3 6-way speaker (1) LOW-MID
OUTPUT 4 6-way speaker (1) MID
OUTPUT 5 6-way speaker (1) HIGH-MID
OUTPUT 6 6-way speaker (1) HIGH
+
[INPUT B]
[INPUT A]
[DIGITAL IN]
AD
AD
Input
Level
Input
Level
Input
Mute
Input
8BandEQ
Input
8BandEQ
Input
Delay
Input
Delay
Input
Mute
Input
8BandEQ
Input
Delay
BA SUM
[OUTPUT 6]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 5]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH-MID
[OUTPUT 4]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
MID
[OUTPUT 3]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW-MID
[OUTPUT 2]
DA
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
LOW
[Library Data]
LOW
HIGH
MID
SUB-LOW
HIGH-MID
LOW-MID
[OUTPUT 1]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
SUB-LOW
Introduction to the SP2060
SP2060 Owner’s Manual
Foreword
Introduction
to the SP2060
Network Settings ReferencesPanel Operation
The Controls
and Connectors
16
Multi Zone
Outputs only the frequency components (by retrieving them from the input signals) that are suitable for the re-
sponse characteristics of each speaker connected to each of six output connectors.
Output connector Speaker’s input connector
OUTPUT 1 1-way speaker (1)
OUTPUT 2 1-way speaker (2)
OUTPUT 3 1-way speaker (3)
OUTPUT 4 1-way speaker (4)
OUTPUT 5 1-way speaker (5)
OUTPUT 6 1-way speaker (6)
+
[INPUT B]
[INPUT A]
[DIGITAL IN]
AD
AD
Input
Level
Input
Level
Input
Mute
Input
8BandEQ
Input
8BandEQ
Input
Delay
Input
Delay
Input
Mute
Input
8BandEQ
Input
Delay
BA SUM
[OUTPUT 1]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 6]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 5]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 4]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 3]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[OUTPUT 2]
DA
X-Over
Output
Delay
Output
6BandEQ
with APF
Output
Level
Output
Mute
LIMIT
Limiter
HIGH
[Library Data]
[Library Data]
[Library Data]
[Library Data]
[Library Data]
[Library Data]
HIGH
HIGH
HIGH
LOW
LOW
LOW
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Introduction to the SP2060
SP2060 Owner’s Manual
17
System Examples
Speaker processing
This diagram indicates an example of a stereo 3-way system.
The AES/EBU input connector on the SP2060 enables you to connect it directly to the AES/EBU output on a
digital mixer.
The configuration presets include 3 x 2-way, 2 x 3-way, 4-way + 2 x Aux, 5-way + Aux, and 6-way. (See page 9.)
The SP2060 Routing function enables you to select IN A, IN B, or IN SUM (A+B) as component input. In this
way, you can create a stereo, mono, or stereo mono (full-range stereo plus mono subwoofer) system very easily.
You can also adjust the parameters or recall a scene from the front panel of the SP2060 or from a computer con-
nected via Ethernet.
Routing
Left/Right (AES/EBU)
* also Analog input available
M7CL
1234 56
XP7000 XP7000 XP7000 XP7000
Subwoofer Bi-amp 2way Subwoofer Bi-amp 2way
Main speaker L Main speaker R
Ethernet
AES/EBU
SP2060
L
R
IN A
IN A+B
IN B
OUT 1
OUT 2
OUT 3
OUT 4
OUT 5
OUT 6
Sub L
Low L
Hi L
Sub R
Low R
Hi R
Introduction to the SP2060
SP2060 Owner’s Manual
Foreword
Introduction
to the SP2060
Network Settings ReferencesPanel Operation
The Controls
and Connectors
18
Zone processing
This example is a stereo 3-zone system in which the SP2060 is used as a signal distributor, rather than a crossover.
Adjusting the routing will enable you to create a monaural 6-zone system. You can adjust EQ, Delay, and Level
for each output.
This system is suitable for a facility that requires sound zoning, such as stores, restaurants, hotels, conference fa-
cilities, and exhibition halls, or for delay speakers in an SR system.
Routing
12 3 4 65
XP7000 XP7000
AB
LR LR LR
ZONE A ZONE B ZONE C
MG16/4
SP2060
XP7000
IN A
IN A+B
IN B
L
R
OUT 1
OUT 2
OUT 3
OUT 4
OUT 5
OUT 6
ZONE 1L
ZONE 1R
ZONE 2L
ZONE 2R
ZONE 3L
ZONE 3R
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Introduction to the SP2060
SP2060 Owner’s Manual
19
Multiple SP2060
This example is a system that uses CobraNet™ for long-distance digital transfer between the control room and
amp room.
Audio signals from Yamaha PM5D digital mixing console, talkback mic signal, chime source, etc. are input to the
DME64N. The output destination and level settings are specified via the Routing function.
Furthermore, you can process output signals (EQ, Limiter, etc.) by adding an EQ component. The output from
the DME64N is converted to CobraNet™ signals via the MY16-C, then transferred via the Ethernet cable to the
NHB32-C located in the amp room.
In the amp room, this signal is converted to the AES/EBU digital signal via the NHB32-C, then input to the
SP2060, which, in turn, processes the signal using the Crossover, EQ, Delay, and Limiter to suit each speaker.
The SP2060 control signal is also transferred to the amp room via the Ethernet cable. (Yamaha recommends that
you use Giga-bit switching hubs.)
HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE
ENTERENTERCANCELCANCEL
88
NETWORK HUB AND BRIDGE
LINK CONDUCT
LOCK
ERROR
Control Room
PM5D
Cascade
Talkback mic
MY16-C
Specifying the
destination and
processing (such
as EQ) for the
output signal
Amp Room
NHB32-C
XP7000 XP7000 XP7000
12 34 56 1234 56
Ethernet
AES/EBU
CobraNet
Main L Main R
Mono Sub Stair Step
Under Balcony Lobby/
Dressing Room
Switching Hub
XM4180 XH200
SP2060 SP2060
DME64N
Switching Hub
Switching Hub Switching Hub
Introduction to the SP2060
SP2060 Owner’s Manual
Foreword
Introduction
to the SP2060
Network Settings ReferencesPanel Operation
The Controls
and Connectors
20
Routing
L
R
IN A
IN A+B
IN B
OUT 1
OUT 2
OUT 3
OUT 4
OUT 5
OUT 6
Low L
Hi L
Low R
Hi R
Mono Sub
Stair Step (Mono)
Under
Balcony
Lobby/
Dressing Room
IN A
IN A+B
IN B
OUT 1
OUT 2
OUT 3
OUT 4
OUT 5
OUT 6
Under Balcony 1
Under Balcony 2
Under Balcony 3
Under Balcony 4
Lobby
Dressing Room
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
SP2060 Owner’s Manual
21
Front Panel
1 Display
Displays the parameters selected for editing and information
about the currently-recalled scene.
Remove the transparent protective film that was applied pri-
or to shipment from the factory.
2 [BACK/STORE] Key
Selects the previous parameter. In the Scene display, it stores
a selected scene.
3 [▲INC/YES]/[▼DEC/NO] Keys
Confirm Yes or No to the change of parameter values or con-
firmation messages.
4 [NEXT/RECALL] Key
Selects the next parameter. In the Library List display or
Scene display, it recalls a selected library or scene respective-
ly.
5 [LEVEL] Key
Displays the input/output level settings. When these settings
are displayed, the key LED lights up.
6 [DELAY] Key
Displays the signal delay time settings. When these settings
are displayed, the key LED lights up.
7 [EQ] Key
Displays the EQ settings. When these settings are displayed,
the key LED lights up.
8 [ROUTING] Key
Displays the selection of the [INPUT] connectors and Out-
put channel signal sources. When these settings are dis-
played, the key LED lights up.
9 [X-OVER] Key
Displays the Crossover settings or library recall options.
When these settings are displayed, the key LED lights up.
) [LIMITER] Key
Displays the Limiter settings. When these settings are dis-
played, the key LED lights up.
! [SCENE] Key
Displays scene store or recall options, or scene edit options.
When these settings are displayed, the key LED lights up.
@ [UTILITY] Key
Displays the SP2060 Utility function settings. When these
settings are displayed, the key LED lights up.
# [MUTE] Key
Displays the Mute settings. When these settings are dis-
played, the key LED lights up. At this time, each [SEL] key
LED indicates the corresponding channel’s Mute On or Off
and the [SEL] keys enable you to turn Mute On or Off for
the corresponding channels.
Holding down the [MUTE] key for two seconds or longer
will turn the User Lock function On or Off.
$ [SEL] Keys
Select the corresponding channels for editing. The [SEL] key
LED for each selected channel lights up.
% Meters
Display the channel level meters and the Limiter indicators
for Output channels.
^ [POWER ON/OFF] Key
Turns mains power to the SP2060 on and off.
The Controls and Connectors
STOR E RECALL
YES
NO
654321BA
1 2 4 5 6 7
! @ # $89)
3 % ^
The Controls and Connectors
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
22
Rear Panel
& Ground Screw
For maximum safety be sure to securely connect the SP2060
ground screw to an earth connection.
The supplied power cable has a three-prong plug that will
ground the unit when plugged into an appropriately ground-
ed three-prong type AC mains outlet. If the AC outlet is not
grounded, be sure to ground the unit by using this ground
screw.
Correct grounding will effectively eliminate hum noise and
interference.
* [AC IN] Connector
Connect to the AC mains using the supplied AC power cord.
First connect the power cord to the SP2060, then insert the
power cord plug into an AC outlet.
( [NETWORK] Connector
This is a 100Base-TX/10Base-T Ethernet connector for con-
nection to a computer or other device in the network.
º [DIGITAL INPUT] Connector (AES/EBU)
Connect an output of an AES/EBU (digital signal) compat-
ible device to this XLR-3-31 connector.
¡ [OUTPUT] Connectors
These XLR-3-32 balanced connectors output six channel an-
alog audio signals. Connect them to the inputs on amplifiers.
™ [INPUT] Connectors
These XLR-3-31 balanced connectors input two channel an-
alog audio signals.
123456
OUTPUT
DIGITAL
INPUT
AES/EBU
( º ¡ ™
& *
NOTE
•Use a CAT5 STP (Shielded Twisted Pair) cable for this
connection to prevent electromagnetic interference. Since the
SP2060 supports Auto MDI/MDI-X, it will automatically
detect whether the connected cable is of the straight type or
crossover type, and will configure itself to create the optimal
connection. Therefore, you can use either a straight or
crossover cable.
• The maximum length of a cable between a switching hub and
the SP2060 is 100 meters. Due to the quality of cables and
switching hub performance, however, proper operation at the
maximum length cannot be guaranteed in some cases.
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
SP2060 Owner’s Manual
23
Basic Operation
Changing the parameter values
You can adjust the parameter settings, such as EQ, according
to the speaker response or the acoustic environment of a par-
ticular venue. This section explains how to change the delay
time for Output channel 1 as an example.
1. Display the parameter setting you wish to
change. To change the delay time, first press
the [DELAY] key to switch to the Delay
display.
Refer to “The Controls and Connectors” on page 21 for
information on the relationship between the parameters
and keys.
2. Select a channel for which you wish to
change the delay time. In this example, press
the OUTPUT 1 [SEL] key.
3. Press the [NEXT] key repeatedly until the
parameter you wish to change appears on the
screen. In this example, select the Time
parameter.
4. Press the [▲ INC]/[▼ DEC] keys to change the
parameter value.
The parameter value on the screen changes accordingly.
This section describes the function of the panel keys and re-
lated displays.
Some parameters will prompt you to confirm the operation
to reflect the change in the value.
In this case, a confirmation icon will appear on the display.
Press the [NEXT] key to move the cursor to the icon, then
press the [YES] key. A message prompts you to confirm.
Press the [YES] key to confirm the operation.
LEVEL
You can view and adjust the Input and Output channel lev-
els.
1. Press the [LEVEL] key to select the Level
display.
2. Press the [SEL] key for the target channel.
The corresponding channel is selected. The [SEL] key
LED for the selected channel lights up.
3. Press the [▲INC]/[▼DEC] keys to adjust the
input or output level.
Panel Operation
[▲ INC]
key
Press the [▲ INC]
key.
The value increases.
Hold down the
[▲ INC] key.
The value continues to
increase as long as you
hold down the key.
While holding down
the [▲ INC] key,
press the [▼ DEC]
key.
The value continues to
increase at a rate more
rapid than when you hold
down the [▲ INC] key.
[▼ DEC]
key
Press the [▼ DEC]
key.
The value decreases.
Hold down the
[▼ DEC] key.
The value continues to
decrease as long as you
down the key.
While holding down
the [▼ DEC] key,
press the [▲ INC]
key.
The value continues to
decrease at a rate more
rapid than when you hold
down the [▼ DEC] key.
OUT 1
ON/OFF = ON
OUT 1
TIME = 2.67ms
Parameter Range
INPUT A/B/SUM –∞, –138.00 through +10.00dB
OUTPUT 1-6 –
∞, –138.00 through +10.00dB
NOTE
When INPUT A/B LINK is turned On, the parameters for
channels A and B are linked and set to the same value
automatically.
SCENE EDIT
01:FOH(Event A)
Confirmation icon
Cursor
IN A
LEVEL =-138.00dB
IN B
LEVEL =-138.00dB
IN B
LEVEL =-138.00dB
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
24
DELAY
You can set the signal delay time on each input and output
channel. Set the On/Off parameter to On to delay the signal,
and Off to bypass the delay.
1. Press the [DELAY] key to select the Delay
display.
2. Press the [SEL] key for the target channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
Pressing the [SEL] keys for Input channels A and B si-
multaneously will turn on the [SEL] key LEDs and select
channel SUM.
3. Press the [▲INC]/[▼DEC] keys to select On or
Off.
4. Press the [DELAY] or [NEXT] key to display
the Time parameter.
5. Press the [▲INC]/[▼DEC] keys to adjust the
delay time.
EQ (Equalizer)
An EQ boosts or cuts the level of specified frequency ranges.
The SP2060’s internal EQ processes input and output sig-
nals.
Input EQ
You can apply eight-band EQ to Input channels A, B, and
SUM.
Set the On/Off parameter to On to apply EQ to the signal,
and Off to not process the signal.
You can set the following parameters for each band.
You can select a type of filter for band 1 and band 8. All other
bands utilize a fixed parametric EQ.
• PEQ
This is a standard parametric equalizer.
• L.SHELF(Low Shelving)
Does not cut the lower frequency range, but cuts starting
from the vicinity of the cutoff frequency toward the higher
range at a specific rate. “6dB/Oct” and “12dB/Oct” stand
for the cut amount per octave.
• H.SHELF(High Shelving)
Does not cut the higher frequency range, but cuts starting
from the vicinity of the cutoff frequency toward the lower
range at a specific rate. “6dB/Oct” and “12dB/Oct” stand
for the cut amount per octave.
• HPF
This is a high pass filter (Q=0.7). The low frequency range
is mildly cut (12dB/Oct), creating a slow curve.
• LPF
This is a low pass filter (Q=0.7). The high frequency range
is mildly cut (12dB/Oct), creating a slow curve.
Parameter Range
INPUT A/B/SUM 0–1300.00msec
OUTPUT 1-6 0–500.00msec
NOTE
Channel SUM is a new channel created by applying the Level and
Mute settings to Input channel A and B respectively, then adding
both channel values.
IN A
ON/OFF = OFF
IN SUM
ON/OFF = OFF
IN SUM
ON/OFF = ON
IN B
TIME = 130.00ms
IN B
TIME = 120.00ms
Parameter Range Function
BYPASS ON/OFF
Sets the bypass for
each frequency range
to On or Off.
Q 16.0–0.1
Specifies the width of
each frequency range.
FREQ
(Frequency)
20.0Hz–20.0kHz
Specifies the center
frequency of each
frequency range.
GAIN
–18dB through
+18.00dB
Sets the gain of the
target frequency.
Parameter Range Function
TYPE
PEQ
L.SHELF 6dB/Oct
L.SHELF 12dB/Oct
H.SHELF 6dB/Oct
H.SHELF 12dB/Oct
HPF
LPF
Selects a type of filter.
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Panel Operation
SP2060 Owner’s Manual
25
1. Press the [EQ] key repeatedly to select the
EQ display.
2. Press the [SEL] key for the target channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
Pressing the [SEL] keys for channels A and B will turn on
the [SEL] key LEDs and select channel SUM.
3. Press the [EQ], [BACK] or [NEXT] key to
display the On/Off parameter.
4. Press the [▲INC] key to set the On/Off
parameter to On to apply EQ to the signal.
Press the [▼DEC] key to set the On/Off
parameter to Off to not process the signal.
5. Press the [BACK] or [NEXT] key to select the
Bypass, Type, Q, Freq, or Gain parameter.
6. Pressing the [EQ] key repeatedly will scroll
the bands from 1 through 8.
7. Press the [▲INC]/[▼DEC] keys to select the
value.
Output EQ
You can apply a 6-band EQ to Output channels 1–6.
Set the On/Off parameter to On to apply EQ to the signal,
and Off to not process the signal.
The parameters are the same as for the input EQ.
You can set the following parameters for each band.
• APF (All Pass Filter)
This filter passes all ranges of frequency, but changes only
the phase. It is used to align the phase in the crossover
range.
APF 1st rotates the phase by 0 through 180 degrees, and
APF 2nd rotates the phase by 0 through 360 degrees. APF
2nd requires the Q setting.
• Horn
A horn speaker typically features a roll-off in the higher
frequency component.
Horn EQ corrects this characteristics. For this purpose,
the gain is limited to 0dB or higher, and the frequency to
500Hz or higher.
IN A
ON/OFF = ON
IN SUM
ON/OFF = ON
IN SUM BAND 2
Q = 0.125
IN SUM BAND 3
Q = 0.125
Parameter Range Function
BYPASS ON/OFF
Sets the bypass
for each
frequency range
to On or Off.
TYPE
PEQ
L.SHELF 6dB/Oct
L.SHELF 12dB/Oct
H.SHELF 6dB/Oct
H.SHELF 12dB/Oct
HPF
LPF
APF 1st
APF 2nd
Horn
Selects a type of
filter.
Q 63.0–0.1
Specifies the
width of each
frequency range.
FREQ
(Frequency)
20.0Hz–20.0kHz
Specifies the
frequency of each
band.
GAIN
–18dB through
+18.00dB
Sets the gain of
the target
frequency.
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
26
ROUTING
Input routing
You can select either analog or digital input signals. This se-
lection links to the word clock master setting. You can also
route the left channel of an input signal received at the [IN-
PUT A] or [DIGITAL IN] connector to both Input chan-
nels A and B.
1. Press the [ROUTING] key to select the
Routing display.
2. Press the [▲INC]/[▼DEC] keys to select an
input signal source.
Output routing
You can route Input channel A, B, and SUM signals to the
Crossover input.
The following three channels are available:
• IN A
• IN SUM
• IN B
1. Press the [ROUTING] key to select the
Routing display.
2. Press the [SEL] key for the target Output
channel.
The [SEL] key LED for the selected channel lights up.
The [SEL] key LED for each channel that shares the
same component flashes. The selected channel name ap-
pears on the display.
3. Press the [▲INC]/[▼DEC] keys to select an
input source to be routed to the Crossover.
Option Input Signal Selection
Word Clock
Master
ANA A/B
A signal at the [INPUT A]
connector is routed to
channel A, and a signal at
the [INPUT B] connector
to channel B.
Internal clock:
96kHz
ANA A/A
A signal at the [INPUT A]
connector is routed to
channels A and B.
DIG L/R
A left channel signal is
routed to channel A, and
a right channel signal to
channel B.
Incoming AES/
EBU signal
DIG L/L
A left channel signal is
routed to channels A and
B.
HINT
You can check the word clock status on the Utility display. See
page 34.
NOTE
Signals are muted while they are switched between analog and
digital to avoid noise.
INPUT SELECT
SOURCE = ANA A/B
INPUT SELECT
SOURCE = ANA A/A
OUT 2
SOURCE = IN A
OUT 4
SOURCE = IN A
OUT 4
SOURCE = IN SUM
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Panel Operation
SP2060 Owner’s Manual
27
X-OVER (Crossover)
Setting the Crossover
Input signals can be divided into specified frequency ranges
to suit speaker response characteristics prior to output.
The number of division is determined to 1-way through 6-
way, depending on the selected component.
1. Press the [X-OVER] key repeatedly until the X-
Over display appears on the screen.
2. Press the [SEL] key for the target Output
channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
3. Press the [NEXT]/[BACK] keys to select a
parameter to edit.
4. Press the [▲INC]/[▼DEC] keys to set the
parameter value.
Parameter Range Function
LEVEL
–
∞, –138.00 through
+10.00dB
Adjusts the level of the
signal input to the
Crossover. The same
Level setting is used
for the output channels
of a component.
POLARITY
NORMAL
INVERTED
The output signal
phase for each
frequency range is
inverted.
HPF
Refer to Step 4.
LPF
OUT 1 LPF
FREQ = 20.0kHz
OUT 3 LPF
FREQ = 20.0kHz
OUT 3 LPF
TYPE =24AdjustGc
Parameter Range Function
HPF
TYPE
Thru
6dB/Oct
12dB/Oct AdjustGc
12dB/Oct Butrwrth
12dB/Oct Bessel
12dB/Oct Linkwitz
18dB/Oct AdjustGc
18dB/Oct Butrwrth
18dB/Oct Bessel
24dB/Oct AdjustGc
24dB/Oct Butrwrth
24dB/Oct Bessel
24dB/Oct Linkwitz
36dB/Oct AdjustGc
36dB/Oct Butrwrth
36dB/Oct Bessel
48dB/Oct AdjustGc
48dB/Oct Butrwrth
48dB/Oct Bessel
48dB/Oct Linkwitz
Selects an
attenuation
amount per
octave, and a
type of filter.
If you select
“Thru,” no filter
will be applied.
FREQ
(Frequency)
20.0Hz–20.0kHz
Specifies the
cutoff frequency
of the high pass
filter.
Gc –6dB through +6dB
You can set the
gain for the cutoff
frequency (Gc)
when you select
“AdjustGc
(Adjustable Gc)”
for the Type
parameter.
LPF
TYPE
Thru
6dB/Oct
12dB/Oct AdjustGc
12dB/Oct Butrwrth
12dB/Oct Bessel
12dB/Oct Linkwitz
18dB/Oct AdjustGc
18dB/Oct Butrwrth
18dB/Oct Bessel
24dB/Oct AdjustGc
24dB/Oct Butrwrth
24dB/Oct Bessel
24dB/Oct Linkwitz
36dB/Oct AdjustGc
36dB/Oct Butrwrth
36dB/Oct Bessel
48dB/Oct AdjustGc
48dB/Oct Butrwrth
48dB/Oct Bessel
48dB/Oct Linkwitz
Selects an
attenuation
amount per
octave, and a
type of filter.
If you select
“Thru,” no filter
will be applied.
FREQ
(Frequency)
20.0Hz–20.0kHz
Specifies the
cutoff frequency
of the low pass
filter.
Gc –6dB through +6dB
You can set the
gain for the cutoff
frequency (Gc)
when you select
“AdjustGc
(Adjustable Gc)”
for the Type
parameter.
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
28
• Thru
No filter is applied. The original characteristics are kept
with no attenuation for all frequency ranges.
• AdjustGc (Adjustable Gc)
Filters with an Adjustable Gc enable you to adjust the gain
at the cutoff frequency in the range of –6dB through
+6dB. With Gc set to –3dB, the filter is practically a But-
terworth filter. And with Gc set to –6dB, the filter is prac-
tically a Linkwitz-Riley filter.
• Butrwrth (Butterworth)
This filter is the most common type of filter. It has a flat
pass band and a –3dB gain at the cutoff frequency.
• Bessel
This filter focuses on the phase characteristics. Although it
has a more gradual roll-off than a Butterworth filter, it will
pass a square wave without causing ringing.
• Linkwitz (Linkwitz-Riley)
This filter features the square of the second order. When
the output signal from its LPF and HPF are combined, the
gain over the entire range is +/–0dB. It has a flat pass band
and a –6dB gain at the cutoff frequency.
LIBRARY
Using libraries facilitates the recall of optimal speaker set-
tings. Up to 60 libraries are available for each component via
the DME Designer application.
Displaying the current library
Pressing the [X-OVER] key repeatedly will select the Cur-
rent Library display, Library List display, or X-Over display,
in this order.
The title of the library most recently recalled for each com-
ponent will be displayed.
Recalling a library
Follow the steps below to recall a library:
1. Press the [X-OVER] key repeatedly until the
Library List display appears on the screen.
2. Press the [SEL] key of an Output channel for
a component for which you wish to recall a
library.
3. Press the [▲INC]/[▼DEC] keys to select a
library.
4. Press the [NEXT/RECALL] key.
A confirmation message will appear.
NOTE
• The type names are abbreviated on the SP2060 screen.
For example, “24dB/Oct Bessel” is displayed as “24Bessel.”
• Gc page is displayed if you select “Adjust Gc” for the Type
parameter.
NOTE
Libraries cannot be displayed or recalled for Input channels. If
you press an Input channel [SEL] key, a message appears.
CURRENT LIBRARY
IF2112/95
LIBRARY LIST
IF2112/64
LIBRARY LIST
IF2112/64
LIBRARY RECALL
ARE YOU SURE?
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Panel Operation
SP2060 Owner’s Manual
29
5. To confirm the selection, press the [YES] key.
The library is recalled and the unit returns to the Library
List display.
To cancel the recall operation, press the [NO] key, in-
stead of the [YES] key. The unit returns to the Library
List display.
LIMITER
You can set up the Output channel limiter.
The Limiter precludes signal levels higher than a specified
threshold to avoid speaker damage from excess output level.
1. Press the [LIMITER] key to select the Limiter
display.
2. Press the [SEL] key for the target channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
3. Press the [LIMITER], [BACK] or [NEXT] key to
display the On/Off parameter.
4. Press the [▲INC] key to set the On/Off
parameter to On to apply the Limiter to the
signal. Press the [▼DEC] key to set the On/
Off parameter to Off to cancel the Limiter.
5. Press the [NEXT]/[BACK] keys to select a
parameter to edit.
6. Press the [▲INC]/[▼DEC] keys to set the
parameter value.
SCENE
About a scene
The SP2060 enables you to store various parameter settings
as part of scene, and recall them via the front panel or re-
motely from DME Designer.
You can store the following settings in a scene:
• Configuration
•Routing
•Parameter sets of all components
• Scene titles
• Scene protection status
• INPUT A/B LINK
• The title of the library most recently recalled
HINT
You can use the library data for speaker processor components for
DME64N/24N that you have created using DME Designer.
Parameter Range Function
THRESHOLD –54 through 0dB
Sets the threshold
value.
ATTACK
FAST
MID
SLOW
MANUAL (0–
120.0ms)
Sets the attack time.
RELEASE
FAST
MID
SLOW
MANUAL
44.1kHz: 6ms–46s,
48kHz: 5ms–42.3s,
88.2kHz: 3ms–23s,
96kHz: 3ms–21.1s
Sets the release time.
If you select Fast,
Mid, or Slow, the unit
automatically sets the
optimum value based
on the maximum
wave length of audio
input to the Limiter.
NOTE
•You can set the attack time only when “Manual” is selected for
the Attack parameter.
•You can set the release time only when “Manual” is selected for
the Release parameter.
LIBRARY LIST
IF2112/95
HINT
You can protect a scene to forbid overwriting.
OUT 1
ON/OFF = ON
OUT 4
ON/OFF = ON
OUT 4
THRESHOLD= -54dB
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
30
Scenes are stored in the preset area and user area.
Preset area
There is a preset scene for each of 12 configurations. These
scenes are numbered 1 through 12. Each scene title has the
same name as the corresponding configuration title.
User area
The user area can accommodate up to 87 user scenes, which
you can store and recall at your discretion. These scenes are
numbered 13 through 99.
Scene indication
The upper row indicates a scene number, property, and title.
The bottom row indicates the configuration title.
Scene property includes the following types:
Recalling a scene
Follow the steps below to recall a scene (1–99):
1. Press the [SCENE] key to select the Scene
Selection display.
2. Press the [▲INC]/[▼DEC] keys to select a
scene number.
While you are selecting a scene, the scene number and ti-
tle will be flashing.
3. Press the [RECALL] key.
A confirmation message will appear.
4. Press the [YES] key.
The scene is recalled and its number becomes the current
scene number.
To cancel the recall operation, press the [NO] key, in-
stead of the [YES] key. The unit returns to the Scene Se-
lection display.
No.1. [3x2way ]
No.2. [3x2way L ]
No.3. [2x(2way+Sub) ]
No.4. [2x(2way+Sub)L ]
No.5. [2x2way+2xAux ]
No.6. [2x2way+2xAux L ]
No.7. [2x3way ]
No.8. [2x3way L ]
No.9. [4way+2xAux ]
No.10. [5way+Aux ]
No.11. [6way ]
No.12. [Multi Zone ]
Preset scene
Protected user scene
Unprotected user scene
NOTE
After you recall a scene, if you edit a parameter, an icon
appears in the lower right corner on the screen.
25:FOH(Event A)
[2x(2way+SUB)L]
Scene propertyScene number Title
Configuration title
HINT
You can also recall a scene using the DME Designer application.
NOTE
If recalling a scene has changed the configuration, audio output
will be muted momentarily.
NOTE
If no data is included in the currently-selected scene, the message
“No Scene” appears.
NOTE
If the selected scene contains no data or User Lock is turned on
for the scene, a status message appears.
25:FOH(Event A)
[2x(2way+SUB)L]
33:RECALL
ARE YOU SURE?
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Panel Operation
SP2060 Owner’s Manual
31
Storing a scene
Follow the steps below to store a scene (13–99) to the user
area:
1. Press the [SCENE] key to select the Scene
Selection display.
2. Press the [▲INC]/[▼DEC] keys to select a
scene number.
3. Press the [BACK/STORE] key.
A confirmation message will appear.
4. Press the [YES] key.
The scene is stored and its number becomes the current
scene number.
To cancel the store operation, press the [NO] key, in-
stead of the [YES] key. The unit returns to the Scene Se-
lection display.
Changing a scene title
Follow the steps below to change the title (up to 13 charac-
ters) of the scene stored for the current scene number:
1. Press the [SCENE] key repeatedly until the
Scene Edit display appears on the screen.
2. Press the [BACK]/[NEXT] keys to move the
cursor to a character you want to edit.
3. Press the [▲INC]/[▼DEC] keys to change the
character.
4. When you finish editing the title, press the
[NEXT] key repeatedly to move the cursor to
the icon, then press the [YES] key.
A confirmation message will appear.
5. To confirm the edit, press the [YES] key.
The title is changed and the unit returns to the Scene
Edit display.
Protecting a scene
Follow the steps below to protect a scene:
1. Press the [SCENE] key repeatedly until the
Scene Edit display appears on the screen.
2. Press the [▲INC]/[▼DEC] keys to select a
scene number.
3. Press the [NEXT] key to move the cursor to
the scene property icon.
4. Press the [▲INC]/[▼DEC] keys to turn
protection on or off.
The protection icon flashes.
HINT
You can also store a scene using the DME Designer application.
NOTE
You cannot change the title of any protected User scenes.
25:FOH(Event A)
[2x(2way+SUB)L]
72:STORE
ARE YOU SURE?
SCENE EDIT
73:FOH(Event A)
SCENE EDIT
73:FOH(Event A)
HINT
Holding down the [▲INC]/[▼DEC] keys will increase the speed
at which the characters scroll.
SCENE EDIT
ARE YOU SURE?
SCENE EDIT
73:FOH(Event A)
SCENE EDIT
73:FOH(Event A)
SCENE EDIT
73 FOH(Event A)
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
32
5. Press the [NEXT] key repeatedly to move the
cursor to the icon, then press the [YES]
key.
A confirmation message will appear.
6. To confirm the edit, press the [YES] key.
The unit reflects the edit and returns to the Scene Edit
display.
Deleting a scene
Follow the steps below to delete a scene:
1. Press the [SCENE] key repeatedly until the
Scene Delete display appears on the screen.
2. Press the [▲INC]/[▼DEC] keys to select a
scene to delete.
3. Press the [NEXT] key to move the cursor to
the icon, then press the [YES] key.
A confirmation message will appear.
4. To confirm the operation, press the [YES] key.
The operation is executed and the unit returns to the
Scene Delete display.
UTILITY
The Utility function enables you to view the word clock sta-
tus and make network settings. See page 37 for more infor-
mation on making network settings.
INPUT A/B LINK
Follow the steps below to link the Input channel A and B pa-
rameters:
When INPUT A/B LINK is turned On, the parameters for
channel A and B are linked and set to the same value auto-
matically.
The following components will be linked:
• INPUT LEVEL
• INPUT EQ
• INPUT DELAY
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the INPUT A/B LINK page
appears.
3. Press the [▲INC] key to link the parameters.
“ON” flashes on the screen.
4. Press the [NEXT] key to move the cursor to
the icon.
5. Press the [YES] key.
A confirmation message will appear.
HINT
You can turn protection on and off from the DME Designer
application.
NOTE
You cannot delete preset scenes, protected scenes, and current
scene.
SCENE EDIT
ARE YOU SURE?
SCENE DELETE
72:FOH(Event A)
SCENE DELETE
ARE YOU SURE?
NOTE
The channel SUM parameters cannot be linked.
INPUT A/B LINK
OFF
INPUT A/B LINK
ON
INPUT A/B LINK
ON
INPUT A/B LINK
ARE YOU SURE?
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Panel Operation
SP2060 Owner’s Manual
33
6. To confirm the operation, press the [YES] key.
The flashing “ON” (or “OFF”) lights up steadily, and the
cursor returns to the “ON (or OFF)” position.
To cancel the operation and return to the original set-
ting, press the [NO] key.
User Lock
Parameter settings can be “locked” temporarily to prevent
accidental mis-operation. This function is useful to avoid
unintentional operations or to prevent others from operating
the panel controls.
The following operations are the User Lock target.
* Editing the parameters
* Recalling and storing a scene
* Changing a scene title
* Changing the scene protection status
* Recalling a library
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the User Lock page appears.
3. Press the [▲INC] key to turn User Lock on. To
cancel User Lock, press the [▼DEC] key.
“ON” flashes on the screen.
4. Press the [NEXT] key to move the cursor to
the icon.
5. Press the [YES] key.
A confirmation message will appear.
6. To confirm the operation, press the [YES] key.
A status message appears, and User Lock becomes active.
Setting the Last Memory Resume
You can select whether at the startup the SP2060 recalls the
scene selected before you turned off the power to the device,
or it starts up with the same status as when it was shut down
last time. The default setting is “ON.”
OFF: At the startup, the SP2060 will recall the scene select-
ed before you turned off the power to the device.
ON: The SP2060 will start up with the same status as
when it was shut down last time.
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the Last Memory Resume
page appears.
NOTE
If you set INPUT A/B LINK to “ON,” the linked parameters for
channel A will be copied to channel B parameters.
NOTE
•You can mute or unmute, or cancel User Lock even if the User
Lock function is turned on.
• The User Lock function is effective only for the panel controls
on the SP2060, and does not affect any control signals from
external devices.
INPUT A/B LINK
ARE YOU SURE?
USER LOCK
OFF
USER LOCK
ON
HINT
•A short cut to turn on the User Lock function is to hold down
the [MUTE] key for two seconds or longer.
•A short cut to turn off the User Lock function is to hold down
the [MUTE] key for two seconds or longer.
USER LOCK
ON
USER LOCK
ARE YOU SURE?
Panel Locked
LAST MEM. RESUME
ON
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
34
3. Press the [▲INC] key so that the SP2060 will
start up with the same status as when it was
shut down last time. Press the [▼DEC] key so
that at the startup the SP2060 will recall the
scene selected before you turned off the
power to the device.
“ON” flashes on the screen.
4. Press the [NEXT] key to move the cursor to
the icon.
5. Press the [YES] key.
A confirmation message will appear.
6. To confirm the operation, press the [YES] key.
The selection is applied and the unit returns to the Last
Memory Resume page.
Displaying the label
You can view the label for the SP2060 that you have set on
DME Designer.
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the Label page appears.
The unit displays the label you created on DME Design-
er.
Displaying word clock
Word clock changes in accordance with input routing set-
tings.
You can view the current word clock status on the display.
One of the following six word clock sources will be dis-
played:
For analog input signals:
The internal clock (Fs=96kHz) is used.
• INT:96kHz : Internal clock (96kHz)
For digital input signals:
The SP2060 synchronizes to an external clock (input at the
AES/EBU connector).
• EXT:44.1kHz : External clock (44.1kHz)
• EXT:48kHz : External clock (48kHz)
• EXT:88.2kHz : External clock (88.2kHz)
• EXT:96kHz : External clock (96kHz)
• EXT:UNLOCK : Unlock to external clock
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display page will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the W. Clock page appears.
NOTE
•You cannot edit the label on the SP2060.
•Up to 14 characters from the top can be displayed.
LAST MEM. RESUME
ON
LAST MEM. RESUME
ON
LAST MEM. RESUME
ARE YOU SURE?
LABEL
[FoH L ]
NOTE
If no signal exists at the [DIGITAL INPUT] connector while
digital input is selected, or if the SP2060 cannot somehow lock to
the incoming signal, an error message appears.
W.CLOCK
[INT: 96kHz]
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Panel Operation
SP2060 Owner’s Manual
35
Checking the backup battery
Follow the steps below to check the internal backup battery
status:
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the Battery page appears.
The remaining battery charge is displayed as follows:
Displaying the firmware version
Follow the steps below to view the current firmware version
number:
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display page will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the Version page appears.
The page indicates the current firmware version number.
You can update the SP2060 firmware via DME Designer.
Refer to the DME Designer Owner’s Manual for details.
You can also download the latest firmware from the follow-
ing Yamaha website.
http://www.yamahaproaudio.com/
Initializing the SP2060
Follow the steps below to initialize the internal memory:
You can select one of the following initialization types:
*Initializing the current scene backup [CURRENT
BACKUP]
*Initializing all user settings (excluding the libraries) to
the factory settings [WITHOUT LIB.]
*Initializing all settings to the factory settings
[FACTORY SETUP]
1. Turn off the power to the SP2060.
2. Turn on the power to the SP2060 while
holding down the [BACK/STORE] key.
The Initialization display appears.
3. Press the [▲INC]/[▼DEC] keys to select a
type of initialization.
4. Press the [NEXT] key to move the cursor to
the icon, then press the [YES] key.
The Initialization operation starts. During initialization,
the following status message appears:
When initialization is completed, the SP2060 displays
the following status message, then automatically restarts.
[OK ] Plenty of charge
[Low Battery] Charge is getting low.
[No Battery ]
Memory data may be lost. Or, no battery
is installed.
“Low Battery” or “No Battery” will appear when the
battery charge is getting low. In this case, save the data to
an external device (such as a computer) immediately, then
ask the Yamaha dealer to replace the backup battery.
HINT
If there is any issue with the backup battery, the SP2060 displays
“Low Battery,” “Critical Battery,” or “No Battery” when you turn
on the power to the unit.
BATTERY
[OK ]
CAUTION
VERSION
[V1.00]
When the internal memory is initialized, all data stored in
the memory will be lost. Use caution when you execute
this function.
NOTE
To cancel the initialization operation, select “Exit” and confirm
the cancellation. Alternatively, simply turn off the power to the
SP2060.
CAUTION
INITIALIZE
FACTORY SETUP
INITIALIZE
EXECUTING..
INITIALIZE
COMPLETED!
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
36
Mute
When Mute is on, the corresponding Input or Output chan-
nel audio is muted.
You can determine the channel Mute status by checking the
corresponding channel [MUTE] key LED.
• MUTE OFF : Dark
• MUTE ON : Illuminated
1. Press the [MUTE] key to select the Mute
display.
2. Press the [SEL] key for the target channel.
The channel audio is muted and the [MUTE] key LED
lights up. Pressing the channel [SEL] key repeatedly tog-
gles between Mute on and off.
NOTE
You can mute or unmute even if the User Lock function is turned
on
NOW SELECT KEYS
ACT "MUTE" ->
1BA
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
SP2060 Owner’s Manual
37
This section describes the network-related settings on the
SP2060 that you need to make when you connect a comput-
er or other external device to the SP2060 [NETWORK]
connector.
Setting a Device Group
A “device group” is a group of multiple SP2060 units that
can be operated in sync via DME Designer. Follow the steps
below to assign each SP2060 in a device group as master or
slave. Each device group must have one master. All other de-
vices in the group are assigned as slave.
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the Device Group page
appears.
3. Press the [▲INC]/[▼DEC] keys to select
“MASTER” or “SLAVE.”
When you change the setting, the parameter setting
flashes.
4. Press the [NEXT] key to move the cursor to
the icon, then press the [YES] key.
A confirmation message will appear.
5. To confirm the setting, press the [YES] key.
The selection is applied and the unit returns to the De-
vice Group page.
Setting the IP Address
Follow the steps below to set the IP address for each SP2060.
Each group of digits between periods in an IP address is
called “octet.” These groups of digits are called “1st octet,”
“2nd octet,” etc., starting from the left-most digit group.
You cannot specify 0, 127, and 223 through 255 for the 1st
octet of the network address.
You can specify the following range of values for the 4th oc-
tet.
Master : 2–253
Slave : 3–253
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the IP Address page appears.
3. Press the [NEXT]/[BACK] keys to move the
cursor to an octet you want to specify.
4. Press the [▲INC]/[▼DEC] keys to change the
value.
When you change the value, the octet flashes.
5. Press the [NEXT] key to move the cursor to
the icon, then press the [YES] key.
A confirmation message will appear.
Network Settings
NOTE
When connecting a computer to an SP2060 via Ethernet, you
must install the appropriate DME-N Network driver on the
computer. You can download the DME-N Network driver from
the Yamaha website.
DEVICE GROUP
MASTER
DEVICE GROUP
SLAVE
DEVICE GROUP
ARE YOU SURE?
NOTE
•Subnet mask is fixed at 255.255.255.0.
•Gateway address is the same network address as the IP address.
The host address is automatically set to 254.
IP ADDRESS
192.168.000.003
Network address Host address
IP ADDRESS
192.168.000.002
IP ADDRESS
192.168.000.003
IP ADDRESS
ARE YOU SURE?
Network Settings
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
38
6. To confirm the setting, press the [YES] key.
The setting is applied and the unit returns to the IP Ad-
dress page.
Setting the Master ID
The SP2060 units that are assigned as slaves in a device
group follow the master SP2060 in the same group via com-
munication. Follow the steps below to set the master ID on
the slave SP2060 units. Use the 4th octet of the IP address of
the master unit as the Master ID parameter value.
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the Master ID page appears.
3. Press the [▲INC]/[▼DEC] keys to set the
value to the same number as the 4th octet of
the master SP2060 IP address.
4. Press the [NEXT] key to move the cursor to
the icon, then press the [YES] key.
A confirmation message will appear.
5. To confirm the setting, press the [YES] key.
The setting is applied and the unit returns to the Master
ID page.
To cancel the operation and return to the original set-
ting, press the [NO] key, instead of the [YES] key.
Setting Link Mode
Follow the steps below to select 100Base-TX or 10Base-T for
the [NETWORK] connector speed.
100Base-TX
The [NETWORK] connector basically operates as 100Base-
TX, but automatically switches to 10Base-T if the network
environment is not compatible with 100Base-TX.
10Base-T
The [NETWORK] connector is compatible with 10Base-T
operation.
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the Link Mode page appears.
3. Press the [▲INC] key to select 100Base-TX,
and the [▼DEC] key to select 10Base-T.
When you change the setting, the parameter setting
flashes.
4. Press the [NEXT] key to move the cursor to
the icon, then press the [YES] key.
A confirmation message will appear.
5. To confirm the setting, press the [YES] key.
The unit reflects the edit and returns to the Link Mode
page.
NOTE
This parameter can be set from 2 through 253.
MASTER ID
253
MASTER ID
ARE YOU SURE?
NOTE
Depending on the specifications of the connected network
devices (such as a switching hub, router, etc.), changing Link
Mode may cause the SP2060 to be unable to reconnect to the
network. In this case, turn the power to the SP2060 off and then
on. The SP2060 will reconnect to the network.
LINK MODE
100BASE-TX
LINK MODE
10BASE-T
LINK MODE
ARE YOU SURE?
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
Network Settings
SP2060 Owner’s Manual
39
Viewing the MAC Address
Follow the steps below to view the SP2060 MAC address:
1. Press the [UTILITY] key to select the Utility
display.
The most recently used Utility display will appear.
2. Press the [UTILITY], [NEXT] or [BACK] key
repeatedly until the MAC Address page
appears.
The bottom row indicates the MAC address.
NOTE
In some cases, you may not need to set the MAC address via the
DME-N Network driver when the SP2060 is communicating
with DME Designer.
MAC ADDRESS
[00A0DE250123]
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
40
About Preset Libraries
File name
•pa........................ Passive mode*
•bi........................ Bi-amp mode
• tri........................ Tri-amp mode
• sub...................... Combining with a subwoofer**
• moni................... For a floor monitor
*Yamaha Installation Series speakers are designed to be used without a speaker processor when Passive mode is
selected. However, using a speaker processor will improve the performance significantly.
** This setting is for full-range speakers. Subwoofer settings are not included.
Subwoofer
• “_sub” settings for 12-inch or 15-inch 3-way full-range speakers are designed for a combination with IS1118,
IS1215, or IS1218.
• The IS1118, IS1215, and IS1218 settings are specified for a monaural subwoofer usage.
• The full-range and subwoofer level balance varies depending on the number of speakers used, installation
conditions, and applications.
•If the full-range speaker baffle and subwoofer baffle are aligned, the speaker polarity will be positive and in-
phase.
Depending on the installation conditions of the subwoofers, you might achieve better results if the subwoofer
phase is inverted.
Limiter
• The default value of the threshold level has been specified based on the maximum analog output level of
+24dBu and amp voltage gain of 26dB (which corresponds to “ATT –6dB” if you are using a Yamaha PC
series amplifier that features a voltage gain of 32dB).
If you are not using the output levels referenced above, change the threshold level.
For example, if you are using an amplifier with a voltage gain of 30dB, lower the threshold level by 4dB.
•Attack time and Release time are both set to “Mid.”
• The Limiter may not completely protect the speakers. Use the Limiter if they suit your environment.
References
LIBRARY LIST
IF211264_pa_sub
LIBRARY LIST
IF2112AS_bi_moni
Model name Drive
mode
Subwoofer usage Model name Drive
mode
Floor monitor
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
References
SP2060 Owner’s Manual
41
Libraries for 1-way speaker processors
The following table shows typical subwoofer settings when it is combined with Yamaha In-
stallation Series speakers.
The following table shows the settings for Yamaha Installation Series speakers (full-range,
passive mode).
NOTE
These libraries also apply to 2-way speakers that are used in passive mode.
Target speakers Library name Meaning
IS1118 and IS1218 IS1118_IS1218
This setting can be shared by IS1118 and IS1218 when IF2112
(M), IF2115 (M) or IF3115 is combined.
IS1215 IS1215
This setting is for IS1215 when IF2112 (M), IF2115 (M) or IF3115
is combined.
Standard subwoofer Sub_5inch&8inch
This LPF setting can be shared by standard subwoofers when
IF2205, IF2108, or IF2208 is combined.
Target speakers Library name Subwoofer
usage*
For a floor
monitor
IF2205
IF2205 – –
IF2205_sub ✓ –
IF2108
IF2108 – –
IF2108_sub ✓ –
IF2108_moni – ✓
IF2208
IF2208 – –
IF2208_sub ✓ –
IF2208_moni – ✓
IF2112/AS
IF2112AS_pa – –
IF2112AS_pa_sub ✓ –
IF2112AS_pa_moni – ✓
IF2112/64
IF211264_pa – –
IF211264_pa_sub ✓ –
IF2112/95
IF211295_pa – –
IF211295_pa_sub ✓ –
IF2112/99
IF211299_pa – –
IF211299_pa_sub ✓ –
IF2112M/64
IF2112M64_pa – –
IF2112M64_pa_sub ✓ –
IF2112M/95
IF2112M95_pa – –
IF2112M95_pa_sub ✓ –
IF2112M/99
IF2112M99_pa – –
IF2112M99_pa_sub ✓ –
IF2115/AS
IF2115AS_pa – –
IF2115AS_pa_sub ✓ –
IF2115AS_pa_moni – ✓
IF2115/64
IF211564_pa – –
IF211564_pa ✓ –
References
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
42
* This setting is for full-range speakers. Subwoofer settings are not included.
Libraries for 2-way speaker processors
The following table shows the settings for Yamaha Installation Series speakers (full-range,
bi-amp mode).
IF2115/95
IF211595_pa – –
IF211595_pa_sub ✓ –
IF2115/99
IF211599_pa – –
IF211599_pa_sub ✓ –
IF2115M/64
IF2115M64_pa – –
IF2115M64_pa_sub ✓ –
IF2115M/95
IF2115M95_pa – –
IF2115M95_pa_sub ✓ –
IF2115M/99
IF2115M99_pa – –
IF2115M99_pa_sub ✓ –
NOTE
These libraries also apply to 3-way speakers (including a combination of IL series and IH series speakers) that are used in bi-
amp mode.
Target speakers Library name Subwoofer
usage*
For a floor
monitor
IF2112/AS
IF2112AS_bi – –
IF2112AS_bi_sub ✓ –
IF2112AS_bi_moni – ✓
IF2112/64
IF211264_bi – –
IF211264_bi_sub ✓ –
IF2112/95
IF211295_bi – –
IF211295_bi_sub ✓ –
IF2112/99
IF211299_bi – –
IF211299_bi_sub ✓ –
IF2112M/64
IF2112M64_bi – –
IF2112M64_bi_sub ✓ –
IF2112M/95
IF2112M95_bi – –
IF2112M95_bi_sub ✓ –
IF2112M/99
IF2112M99_bi – –
IF2112M99_bi_sub ✓ –
IF2115/AS
IF2115AS_bi – –
IF2115AS_bi_sub ✓ –
IF2115AS_bi_moni – ✓
IF2115/64
IF211564_bi – –
IF211564_bi_sub ✓ –
Target speakers Library name Subwoofer
usage*
For a floor
monitor
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
References
SP2060 Owner’s Manual
43
* This setting is for full-range speakers. Subwoofer settings are not included.
The following table shows the settings for Yamaha Installation Series speaker IL series along
with IH series.
Libraries for 3-way speaker processors
The following table shows the settings for Yamaha Installation Series speakers (full-range,
tri-amp mode).
The following table shows the settings for Yamaha Installation Series speaker IL series along
with IH series.
IF2115/95
IF211595_bi – –
IF211595_bi_sub ✓ –
IF2115/99
IF211599_bi – –
IF211599_bi_sub ✓ –
IF2115M/64
IF2115M64_bi – –
IF2115M64_bi_sub ✓ –
IF2115M/95
IF2115M95_bi – –
IF2115M95_bi_sub ✓ –
IF2115M/99
IF2115M99_bi – –
IF2115M99_bi_sub ✓ –
IF3115/64
IF311564_bi – –
IF311564_bi_sub ✓ –
IF3115/95
IF311595_bi – –
IF311595_bi_sub ✓ –
IH2000/64 IH200064_bi – –
IH2000/95 IH200095_bi – –
Target speakers Library name Meaning
IL1115 and IH2000/64 IL1115+IH64_pa Combination of IL1115 and IH2000/64 (passive mode)
IL1116 and IH2000/95 IL1115+IH95_pa Combination of IL1115 and IH2000/95 (passive mode)
Target speakers Library name Subwoofer
usage
IF3115/64
IF311564_tri –
IF311564_tri_sub ✓
IF3115/95
IF311595_tri –
IF311595_tri_sub ✓
Target speakers Library name Meaning
IL1115 and IH2000/64 IL1115+IH64_bi Combination of IL1115 and IH2000/64 (bi-amp mode)
IL1115 and IH2000/95 IL1115+IH95_bi Combination of IL1115 and IH2000/95 (bi-amp mode)
Target speakers Library name Subwoofer
usage*
For a floor
monitor
References
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
44
Display Messages
Warning and error messages
* Do NOT turn off the power to the SP2060 while the unit displays the message “DO NOT TURN OFF!” at the bottom of the display.
Message Meaning Action
Duplicate IP Adr. Duplicate IP addresses. Change the IP addresses so that there are no duplicates.
Illegal MAC Adr. An illegal MAC address has been encountered.
This could be due to a hardware malfunction. Refer this
problem to a contact a Yamaha dealer.
Invalid IP Adr. The IP address is not set properly. Set an appropriate network IP address.
Network Error
A cable is disconnected, the power to the
connected switching hub or router is turned off, or a
cable is not in proper condition.
Connect the cables properly, and make sure that the hub
and/or router are operating correctly.
No MAC Adr. MAC address not specified.
This could be due to a hardware malfunction. Refer this
problem to a Yamaha dealer.
No Battery
The internal battery is completely discharged or not
installed.
If you turn off the power to the unit, the current settings will
be lost and reset to the default values. Stop operating the
unit, and contact a Yamaha dealer for battery replacement.
Critical Battery
The internal battery is almost discharged. Your data
may be lost.
If you turn off the power to the unit, the current settings may
be lost and reset to the default values. Stop operating the
unit, and contact a Yamaha dealer for battery replacement.
Low Battery The backup battery voltage is low.
This does not affect the operation of the unit. However, if you
continue using the unit, the settings may be lost and reset to
the default values. Contact a Yamaha dealer for battery
replacement at your earliest convenience.
Recovering
A program update attempt has failed, and the
previous program is currently being restored.
Do NOT turn power off while the unit is displaying this
message. If the update attempt repeatedly fails, there may
be a hardware malfunction. Refer this problem to a Yamaha
dealer.
Scene Recall Err A scene recall attempt has failed.
Recall the scene again.
If the problem persists, contact a Yamaha dealer.
Saving Failed A save operation has failed.
This could be due to a hardware malfunction. Refer this
problem to a Yamaha dealer.
Param Access Err Current setting cannot be displayed. Save the current setting by using DME Designer, then
initialize the unit. If the problem persists, contact a Yamaha
dealer.
Param Set Err Current setting cannot be changed.
W.Clk Unlocked
A usable word clock signal is not being received or
cannot be detected.
Recheck all word clock connections and internal
parameters.
DevGrp Sync Err
The device group configuration set via DME
Designer does not match the real configuration.
Use DME Designer to go off-line, create a configuration that
correctly matches the actual configuration, and then go
back on-line to synchronize the configuration.
System Error A system error has occurred.
Save the current setting by using DME Designer, then
initialize the unit. If the problem persists, contact a Yamaha
dealer.
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
References
SP2060 Owner’s Manual
45
Status messages
* Do NOT turn off the power to the SP2060 while the unit displays the message “DO NOT TURN OFF!” at the bottom of the display.
Troubleshooting
Message Meaning
Connecting Connecting to the network.
Download Success The program has been successfully updated.
Downloading Program update in progress. Do NOT turn power off while the unit displays this message.
File Operating
A file operation is in progress during which the computer manipulates scene data. Do NOT turn power off
while the unit displays this message.
Network Setup Preparing network connection.
Panel Locked The User Lock function is engaged. The panel controls do not work.
Panel Unlocked The User Lock function has been disengaged. Panel operation is now possible.
Scene Recalling Scene recall in progress.
Scene Storing Scene store in progress. Do NOT turn power off while the unit displays this message.
Cannot Recall Recalling scenes or libraries is disabled.
Cannot Store The scene store is disabled.
NO X-OVER Input channels do not feature the X-Over parameter.
NO LIMITER Input channels do not feature the Limiter parameter.
Protected You cannot edit or delete protected scenes.
Panel Protected If the User Lock function is turned on, you cannot change the parameters by using the panel controls.
NO ROUTING Input channel SUM does not feature the Routing parameter.
NO LEVEL Input channel SUM does not feature the Level parameter.
Network Busy There is too much network traffic. Communication is very slow.
Synchronizing Data is being received from the computer. Do NOT turn power off while the unit displays this message.
Scene Deleting Deleting a scene. Do NOT turn power off while the unit displays this message.
Symptom Possible Causes Possible Solutions
No communication between the
SP2060 and the DME Designer
application software.
The connection cable is not connected properly. Make sure that the cable is properly connected.
The computer's Ethernet port is not functioning
properly.
Refer to the DME Designer Installation Guide.
The DME-N Network driver has not been
installed.
Install and set up the DME-N Network driver.
No audio output.
The Mute function is turned on. Turn off the Mute function (see page 36).
The output level is set too low. Increase the output level (see page 23).
The parameters cannot be edited. The User Lock function is turned on. Turn off the User Lock function (see page 33).
References
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
46
General Specifications
Electrical Characteristics
Output impedance of signal generator: 150 Ω
Frequency Response
Total Harmonic Distortion
Hum & Noise
Dynamic Range
Sampling Frequency
External
Normal Rate: 44.1, 48 kHz (±0.1%)
Double Rate: 88.2, 96 kHz (±0.1%)
Internal 96 kHz
Signal Delay
Less than 761 µ sec (INPUT to OUTPUT @Fs=96kHz)
Indicators
Key indicators x 9
MUTE indicators (INPUT A/B, OUTPUT 1–6)
6-segment LED level meters (INPUT A/B, OUTPUT 1–6)
Miscellaneous
Power Consumption 30 W
Dimensions (HxDxW) 44 x 361 x 480 mm
Net Weight 4.2 kg
Temperature Range
Operating: 5 to 40 ˚C
Storage: –20 to 60 ˚C
Included Accessories AC power cord, Rubber feet x 4, Owner’s manual
Input Output RL Conditions MIN TYP MAX Units
INPUT A, B OUTPUT 1–6 600 Ω
Fs=96kHz@20Hz–40kHz, reference to
the nominal output level @1kHz
–1.0 0.0 +0.5 dB
Input Output RL Conditions MIN TYP MAX Units
INPUT A, B OUTPUT 1–6 600 Ω
Fs=96kHz, +4dBu@20Hz–40kHz 0.05 %
Fs=96kHz, +22dBu@1kHz 0.007 %
DIGITAL INPUT
AES/EBU
OUTPUT 1–6 600 Ω Fs=48kHz@1kHz, Input level: –1dBFS 0.015 %
* Total Harmonic Distortion is measured with a 18dB/octave filter @80kHz.
Input Output RL Conditions MIN TYP MAX Units
INPUT A, B OUTPUT 1–6 600 Ω Fs=96kHz, Rs=150 Ω –82 –79 dBu
DIGITAL INPUT
AES/EBU
OUTPUT 1–6 600 Ω Fs=48kHz, Input level: –∞dBFS –86 dBu
*Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave
attenuation.
Input Output RL Conditions MIN TYP MAX Units
INPUT A, B OUTPUT 1–6 600 Ω Fs=96kHz 106 dB
DIGITAL INPUT
AES/EBU
OUTPUT 1–6 600 Ω Fs=48kHz 110 dB
*Dynamic range is measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave
attenuation.
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
References
SP2060 Owner’s Manual
47
Crosstalk@1KHz Fs=96kHz
LED Level Meters
Input/Output Characteristics
Analog Input Characteristics
Analog Output Characteristics
Digital Input Characteristics
Input Output Conditions MIN TYP MAX Units
INPUT A OUTPUT 2, 4, 6
INPUT A assigned to OUTPUT 1, 3 or 5
INPUT B assigned to OUTPUT 2, 4 or 6
–80 dB
INPUT B OUTPUT 1, 3, 5
INPUT A assigned to OUTPUT 1, 3 or 5
INPUT B assigned to OUTPUT 2, 4 or 6
–80 dB
*Crosstalk is measured with a 18dB/octave filter @80kHz.
Metering points Conditions MIN TYP MAX Units
INPUT A, B
OVER red LED: On 0 dBFS
–6 amber LED: On –6 dBFS
–12 amber LED: On –12 dBFS
–18 amber LED: On –18 dBFS
–30 green LED: On –30 dBFS
–48 green LED: On –48 dBFS
OUTPUT 1–6
OVER red LED: On 0 dBFS
LIMIT amber LED: On LIMIT*
–6 green LED: On –6 dBFS
–12 green LED: On –12 dBFS
–18 green LED: On –18 dBFS
–40 green LED: On –40 dBFS
*The LED turns on when the internal limiter is activated.
Input Terminals Actual Load
Impedance
For Use With
Nominal
Input level Connector
Nominal Max. before clip
INPUT A, B 10 k Ω 600 Ω Lines +4 dBu (1.23 V) +24 dBu (12.28 V) XLR-3-31 type (balanced) *1
*1. XLR-3-31 type connectors with latches are balanced. (1=GND, 2=HOT, 3=COLD)
*2. In these specifications, 0 dBu is referenced to 0.775 Vrms.
*3. All AD converters are 24-bit linear, 64-times oversampling. (Fs=96kHz)
Output
Terminals
Actual Load
Impedance
For Use With
Nominal
Input level Connector
Nominal Max. before clip
OUTPUT 1–6 75 Ω 600 Ω Lines +4 dBu (1.23 V) +24 dBu (12.28 V) XLR-3-32 type (balanced) *1
*1. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*2. In these specifications, 0 dBu is referenced to 0.775 Vrms.
*3. All DA converters are 24-bit linear, 128-times oversampling (Fs=48kHz) or 64-times oversampling (Fs=96kHz).
Terminal Format Data length Level Connector
DIGITAL INPUT AES/EBU AES/EBU 24 bit RS422 XLR-3-31 type (balanced) *1 *2
*1. XLR-3-31 type connector with latch is balanced. (1=GND, 2=HOT, 3=COLD)
*2. Only Double Speed Format is supported at 96 kHz. Double Channel or Single Format is not supported.
References
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
48
Control I/O Characteristics
Connector Pin Assignment
[NETWORK] Connector (100Base-TX Ethernet, RJ-45)
Terminal Format Level Connector
Network IEEE 802.3 10Base-T/100Base-TX RJ-45
Pin Connection
1 TxD+
2 TxD-
3 RxD+
4 Unused
5 Unused
6 RxD-
7 Unused
8 Unused
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
References
SP2060 Owner’s Manual
49
Dimensions
* Specifications and descriptions in this owner's manual are for information purpose only. Yamaha Corp. reserves the right to
charge or modify products or specifications at any time without prior notice. Since specifications, equipment or options may
not be the same in every locale, please check with your Yamaha dealer.
European models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: 35A
Conforms to Environments: E1,E2,E3 and E4.
440
480
361
354
3
44
1
(4)
Rubber feet
are included in
the package.
Unit: mm
References
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
50
Index
[▲INC/YES]/[▼DEC/NO] Keys ........................................... 21
100Base-TX
............................................................................ 38
10Base-T
................................................................................. 38
2 x (2-way + Sub)
.................................................................... 10
2 x (2-way + Sub) Link
............................................................ 10
2 x 2-way + 2 x Aux
................................................................. 11
2 x 2-way + 2 x Aux Link
........................................................ 11
2 x 3-way
................................................................................. 12
2 x 3-way Link
........................................................................ 12
3 x 2-way
................................................................................... 9
3 x 2-way Link
.......................................................................... 9
4 way +2 x Aux
........................................................................ 13
5-way + Aux
............................................................................ 14
6-way
...................................................................................... 15
A
About a scene .......................................................................... 29
[AC IN] Connector
................................................................. 22
AdjustGc (Adjustable Gc)
....................................................... 28
B
[BACK/STORE] Key .............................................................. 21
Battery page
............................................................................ 35
Bessel
...................................................................................... 28
Butrwrth (Butterworth)
........................................................... 28
C
Changing a scene title ............................................................. 31
Changing the parameter values
................................................ 23
Checking the backup battery
................................................... 35
Components
............................................................................. 8
Configuration
.......................................................................8, 9
2 x (2-way + Sub)
............................................................ 10
2 x (2-way + Sub) Link
.................................................... 10
2 x 2-way + 2 x Aux
......................................................... 11
2 x 2-way + 2 x Aux Link
................................................ 11
2 x 3-way
......................................................................... 12
2 x 3-way Link
................................................................ 12
3 x 2-way
........................................................................... 9
3 x 2-way Link
.................................................................. 9
4 way +2 x Aux
................................................................ 13
5-way + Aux
.................................................................... 14
6-way
.............................................................................. 15
Multi Zone
..................................................................... 16
Connector Pin Assignment
...................................................... 48
[CURRENT BACKUP]
......................................................... 35
D
DELAY ................................................................................... 24
[DELAY] Key
.......................................................................... 21
Deleting a scene
...................................................................... 32
Device Group page
..................................................................37
[DIGITAL INPUT] Connector (AES/EBU)
...........................22
Dimensions
..............................................................................49
Display
....................................................................................21
Displaying the current library
..................................................28
Displaying the firmware version
...............................................35
Displaying the label
..................................................................34
Displaying word clock
..............................................................34
DME Designer
..........................................................................7
E
Electrical Characteristics ..........................................................46
EQ (Equalizer)
.........................................................................24
[EQ] Key
.................................................................................21
F
[FACTORY SETUP] ..............................................................35
Features
.....................................................................................8
Firmware Version
......................................................................7
Front Panel
..............................................................................21
G
General Specifications ..............................................................46
Ground Screw
..........................................................................22
H
H.SHELF(High Shelving) .......................................................24
HPF
.........................................................................................24
I
Initializing the SP2060 ............................................................35
INPUT A/B LINK
..................................................................32
INPUT A/B LINK page
..........................................................32
Input channel A
.......................................................................26
Input channel B
.......................................................................26
Input channel SUM
.................................................................26
[INPUT] Connectors
...............................................................22
Input EQ
.................................................................................24
Input routing
...........................................................................26
Input/Output Characteristics
...................................................47
IP address
.................................................................................37
IP Address page
........................................................................37
L
L.SHELF(Low Shelving) ..........................................................24
Label page
................................................................................34
Last Memory Resume page
......................................................33
LEVEL
....................................................................................23
[LEVEL] Key
...........................................................................21
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
References
SP2060 Owner’s Manual
51
LIBRARY ............................................................................... 28
Library
...................................................................................... 8
LIMITER
............................................................................... 29
Limiter
.................................................................................... 40
[LIMITER] Key
...................................................................... 21
Link Mode page
...................................................................... 38
Linkwitz (Linkwitz-Riley)
....................................................... 28
LPF
......................................................................................... 24
M
MAC Address page ................................................................. 39
Master
..................................................................................... 37
Master ID page
....................................................................... 38
Meters
..................................................................................... 21
Multi Zone
............................................................................. 16
Multiple SP2060
..................................................................... 19
Mute
....................................................................................... 36
[MUTE] Key
.......................................................................... 21
N
[NETWORK] Connector ....................................................... 22
Network Settings
.................................................................... 37
[NEXT/RECALL] Key
........................................................... 21
O
octet ........................................................................................ 37
[OUTPUT] Connectors
......................................................... 22
Output EQ
............................................................................. 25
Output routing
....................................................................... 26
P
Parameters ................................................................................ 8
PEQ
........................................................................................ 24
[POWER ON/OFF] Key
........................................................ 21
Preset area
............................................................................... 30
Preset Libraries
........................................................................ 40
preset parameters
....................................................................... 8
preset scene (read-only scene)
.................................................... 9
Protecting a scene
.................................................................... 31
R
Rear Panel ............................................................................... 22
Recalling a library
................................................................... 28
Recalling a scene
..................................................................... 30
ROUTING
............................................................................. 26
[ROUTING] Key
................................................................... 21
S
SCENE ................................................................................... 29
Scene
......................................................................................... 8
[SCENE] Key
......................................................................... 21
scene number
...........................................................................30
scene property
..........................................................................30
[SEL] Keys
...............................................................................21
Setting a Device Group
............................................................37
Setting Link Mode
...................................................................38
Setting the Crossover
...............................................................27
Setting the IP Address
..............................................................37
Setting the Last Memory Resume
............................................33
Setting the Master ID
..............................................................38
Slave
........................................................................................37
Speaker
....................................................................................17
Speaker processing
...................................................................17
Status messages
........................................................................45
Storing a scene
.........................................................................31
Subwoofer
................................................................................40
System Examples
.....................................................................17
T
Thru ........................................................................................28
Troubleshooting
......................................................................45
Turning the power on and off
....................................................7
U
User area ..................................................................................30
User Lock
................................................................................33
User Lock page
........................................................................33
user scene (readable and writable scene)
.....................................9
UTILITY
.................................................................................32
[UTILITY] Key
.......................................................................21
V
Version page ............................................................................35
Viewing the MAC Address
......................................................39
W
W. Clock page .........................................................................34
Warning and error messages
....................................................44
[WITHOUT LIB.]
..................................................................35
X
X-OVER (Crossover) ...............................................................27
[X-OVER] Key
........................................................................21
Z
Zone processing .......................................................................18
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
52
MEMO
References
Introduction
to the SP2060
Foreword
The Controls
and Connectors
Network Settings Panel Operation
SP2060 Owner’s Manual
53
MEMO
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction
to the SP2060
The Controls
and Connectors
54
MEMO
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más cercana
o el distribuidor autorizado que se lista debajo.
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
MEXICO
Yamaha de México S.A. de C.V.
Calz. Javier Rojo Gómez #1149,
Col. Guadalupe del Moral
C.P. 09300, México, D.F., México
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Av. Reboucas 2636-Pinheiros CEP: 05402-400
Sao Paulo-SP. Brasil
Tel: 011-3085-1377
ARGENTINA
Yamaha Music Latin America, S.A.
Sucursal de Argentina
Viamonte 1145 Piso2-B 1053,
Buenos Aires, Argentina
Tel: 1-4371-7021
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: +507-269-5311
THE UNITED KINGDOM
Yamaha-Kemble Music (U.K.) Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: 01908-366700
GERMANY
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Central Europe GmbH,
Branch Switzerland
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 01-383 3990
AUSTRIA
Yamaha Music Central Europe GmbH,
Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/SLOVAKIA/
HUNGARY/SLOVENIA
Yamaha Music Central Europe GmbH,
Branch Austria, CEE Department
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-602039025
POLAND
Yamaha Music Central Europe GmbH
Sp.z. o.o. Oddzial w Polsce
ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland
Tel: 022-868-07-57
THE NETHERLANDS/
BELGIUM/LUXEMBOURG
Yamaha Music Central Europe GmbH,
Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040
FRANCE
Yamaha Musique France
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
ITALY
Yamaha Musica Italia S.P.A.
Combo Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha-Hazen Música, S.A.
Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: 91-639-8888
SWEDEN
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1
Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
DENMARK
YS Copenhagen Liaison Office
Generatorvej 6A
DK-2730 Herlev, Denmark
Tel: 44 92 49 00
NORWAY
Norsk filial av Yamaha Scandinavia AB
Grini Næringspark 1
N-1345 Østerås, Norway
Tel: 67 16 77 70
OTHER EUROPEAN COUNTRIES
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2313
TURKEY/CYPRUS
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
LB21-128 Jebel Ali Freezone
P.O.Box 17328, Dubai, U.A.E.
Tel: +971-4-881-5868
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
25/F., United Plaza, 1468 Nanjing Road (West),
Jingan, Shanghai, China
Tel: 021-6247-2211
INDONESIA
PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
KOREA
Yamaha Music Korea Ltd.
Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong,
Youngdungpo-ku, Seoul, Korea
Tel: 02-3770-0660
MALAYSIA
Yamaha Music Malaysia, Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 3-78030900
SINGAPORE
Yamaha Music Asia Pte., Ltd.
#03-11 A-Z Building
140 Paya Lebor Road, Singapore 409015
Tel: 747-4374
TAIWAN
Yamaha KHS Music Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd. Taipei.
Taiwan 104, R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
891/1 Siam Motors Building, 15-16 floor
Rama 1 road, Wangmai, Pathumwan
Bangkok 10330, Thailand
Tel: 02-215-2626
OTHER ASIAN COUNTRIES
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2317
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2313
NORTH AMERICA
CENTRAL & SOUTH AMERICA
EUROPE
AFRICA
MIDDLE EAST
ASIA
OCEANIA
HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2441
PA13
WG50780 605IPDHx.x-02B0
This document is printed on chlorine free (ECF) paper with soy ink.
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
Yamaha Pro Audio global web site:
http://www.yamahaproaudio.com/
© 2006 Yamaha Corporation
U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
Printed in Japan
Documenttranscriptie
Owner’s Manual EN Precautions for Using a Rack-mounted SP2060 If several SP2060 units (or an SP2060 unit together with other devices) are installed in a poorly-ventilated rack, the heat generated by each unit may raise the temperature inside the rack, preventing the SP2060 from performing as designed. When mounting SP2060 units in a rack, please leave one rack space vacant for every two units. You can attach a ventilation panel to this space or leave it open to prevent excessive heat build-up. If the temperature inside the rack is expected to rise above 40 degrees Celsius or 104 degrees Fahrenheit (or if the ambient temperature outside the rack is expected to rise above 30 degrees Celsius or 86 Fahrenheit), install a fan kit in the top row of the rack. The fan must provide airflow of 1.6 m3/min or more and static pressure of 5 mmH2O or more. Vorsichtsmaßnahmen für den Einsatz eines im Rack montierten SP2060 Wenn in einem schlecht belüfteten Rack mehrere SP2060Einheiten (oder eine SP2060-Einheit zusammen mit anderen Geräten) untergebracht sind, kann die von den Geräten erzeugte Wärme die Temperatur im Rack erhöhen, was die vorgesehene Leistung des SP2060 beeinträchtigt. Wenn Sie SP2060-Einheiten in einem Rack einbauen, lassen Sie bitte alle zwei Geräte einen RackPlatz frei. Sie können an diesem Platz eine Lüftungsverkleidung anbringen oder ihn offen lassen, um die Entwicklung übermäßiger Hitze zu verhindern. FR Si vous craignez que la température à l’intérieur du rack ne dépasse 40 degrés Celsius ou 104 degrés Fahrenheit (ou que la température ambiante à l’extérieur du rack ne dépasse 30 degrés Celsius ou 86 degrés Fahrenheit), installez un kit de ventilation sur la rangée supérieure du rack. Le ventilateur doit fournir un flux d’air de 1,6 m3/min ou plus et une pression statique de 5 mmH2O ou plus. Precauciones para utilizar una SP2060 de montaje en bastidor Si se instalan varias unidades SP2060 (o una unidad SP2060 con otros dispositivos) en un bastidor insuficientemente ventilado, el calor generado por cada unidad podría aumentar la temperatura en el interior del bastidor, impidiendo que la unidad SP2060 funcione de la manera prevista. Cuando monte unidades SP2060 en un bastidor, deje un espacio de bastidor libre por cada dos unidades. Puede instalar un panel de ventilación en este espacio, o bien dejarlo abierto para evitar la acumulación de un calor excesivo. DE Wenn zu erwarten ist, dass die Temperatur im Rack über 40 Grad Celsius oder 104 Grad Fahrenheit ansteigt (oder wenn die Umgebungstemperatur außerhalb des Racks über 30 Grad Celsius oder 86 Grad Fahrenheit ansteigt), installieren Sie eine Lüftereinheit im Rack. Der Lüfter muss einen Luftdurchsatz von mindestens 1,6 m3/Minute oder mehr haben und einen statischen Druck von 5 mmH2O erzeugen können. Précautions à prendre en cas d’utilisation d’un SP2060 monté en rack Si vous installez plusieurs SP2060 (ou un SP2060 et d’autres périphériques) dans un rack mal aéré, la chaleur générée par chaque unité risque d’augmenter la température à l’intérieur du rack et d’empêcher le SP2060 de fonctionner correctement. Lorsque vous montez des SP2060 en rack, laissez un espace libre équivalant à un rack entre deux unités. Vous pouvez recouvrir cet espace d’un panneau de ventilation ou le laisser ouvert pour éviter toute accumulation de chaleur excessive. EN ES Si se espera que la temperatura interior del bastidor supere los 40 grados Celsius (o que la temperatura ambiente fuera del bastidor supere los 30 grados Celsius), instale un kit de ventilación en la fila superior del bastidor. El ventilador debe proporcionar una corriente de aire de 1,6 m3/min o más y una presión de 5 mmH2O o más. Fan kit SP2060 SP2060 Ventilation panel SP2060 SP2060 U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2007 Yamaha Corporation Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 9 10 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 12 13 14 Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. (98-6500) This product contains a battery that contains perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate) FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Yamaha Corporation of America Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620 Telephone : 714-522-9011 Type of Equipment : SPEAKER PROCESSOR Model Name : SP2060 This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B) ADVARSEL! Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. (lithium caution) (FCC DoC) NEDERLAND / THE NETHERLANDS • Dit apparaat bevat een lithium batterij voor geheugen back-up. • This apparatus contains a lithium battery for memory back-up. • Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur afdankt of de volgende Yamaha Service Afdeiing: Yamaha Music Nederland Service Afdeiing Kanaalweg 18-G, 3526 KL UTRECHT Tel. 030-2828425 • For the removal of the battery at the moment of the disposal at the end of the service life please consult your retailer or Yamaha Service Center as follows: Yamaha Music Nederland Service Center Address : Kanaalweg 18-G, 3526 KL UTRECHT Tel : 030-2828425 • Gooi de batterij niet weg, maar lever hem in als KCA. • Do not throw away the battery. Instead, hand it in as small chemical waste. IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN-andYELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. (lithium disposal) • This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.(3 wires) PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device. • Do not expose the device to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings. • Use only the included power cord. If you intend to use the device in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer. • Never insert or remove an electric plug with wet hands. • Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. • If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the device, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. • Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock. If you notice any abnormality • If this device should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. Do not open • Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: • Do not place the device in an unstable position where it might accidentally fall over. Power supply/Power cord • Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Doing so may result in noise, both in the device itself and in the TV or radio next to it. • When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. Connections Location • Before moving the device, remove all connected cables. • When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. • Avoid setting all equalizer controls and faders to their maximum. Depending on the condition of the connected devices, doing so may cause feedback and may damage the speakers. • Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. (5)-4 4 SP2060 Owner’s Manual • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. • Be sure to connect to a properly grounded power source. A ground screw is provided on the rear panel of this device for maximum safety and shock prevention. If the mains outlet is not grounded, be sure to connect the ground screw to a confirmed ground point before plugging the device into the mains. Improper grounding can result in electrical shock. Maintenance • Remove the power plug from the AC outlet when cleaning the device. 4/2 Handling caution Backup battery • Do not use the device for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. • Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors. • This device has a built-in backup battery. When you unplug the power cord from the AC outlet, the current scene data is retained. However, the life of the backup battery is about five years. If the battery wears out, the current scene data will be lost. When the backup battery charge becomes low, the unit first displays “LOW BATTERY” then “CRITICAL BATTERY” when you turn on the power to the unit. (The Battery page of the Utility display also indicates first “Low Battery” then “No Battery” when the charge becomes low.) In this case, please have qualified Yamaha service personnel replace the backup battery. The rubber feet included in this package can be attached to the bottom of this device to prevent slippage when it is to be used on a slipper y surface. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. Always turn the power off when the device is not in use. The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualifi ed Yamaha service personnel about replacing defective components. • • • • The illustrations in this document are for instructional purposes, and may appear somewhat different from the actual equipment. CobraNet is a trademark of Cirrus Logic, Inc. Ethernet is a trademark of Xerox Corporation. All other trademarks are the property of their respective holders and are hereby acknowledged. (5)-4 5/2 SP2060 Owner’s Manual 5 Foreword Contents Foreword .......................................... 7 Introduction to the SP2060 Accessories (Please make sure the following items are included in the package.)................................................. About the Firmware Version ........................................... About DME Designer ..................................................... Precautions for Using a Rack-mounted SP2060 .............. Preparation...................................................................... 7 7 7 7 7 Connecting the AC power cord........................................... 7 Turning the power on and off ............................................. 7 Introduction to the SP2060 ..................... 8 The Controls and Connectors Features........................................................................... 8 Glossary for the SP2060 .................................................. 8 Configuration ................................................................. 9 Panel Operation 3 x 2-way ............................................................................ 9 3 x 2-way Link .................................................................... 9 2 x (2-way + Sub) .............................................................. 10 2 x (2-way + Sub) Link...................................................... 10 2 x 2-way + 2 x Aux .......................................................... 11 2 x 2-way + 2 x Aux Link .................................................. 11 2 x 3-way .......................................................................... 12 2 x 3-way Link .................................................................. 12 4 way +2 x Aux ................................................................. 13 5-way + Aux ...................................................................... 14 6-way ................................................................................ 15 Multi Zone ....................................................................... 16 System Examples........................................................... 17 Speaker processing ............................................................ 17 Zone processing ................................................................ 18 Multiple SP2060............................................................... 19 The Controls and Connectors.................. 21 Network Settings Front Panel ................................................................... 21 Rear Panel ..................................................................... 22 Panel Operation ................................. 23 Basic Operation............................................................. 23 Changing the parameter values.......................................... 23 References LEVEL.......................................................................... 23 DELAY ......................................................................... 24 EQ (Equalizer) .............................................................. 24 Input EQ .......................................................................... 24 Output EQ ....................................................................... 25 ROUTING................................................................... 26 Input routing .................................................................... 26 Output routing ................................................................. 26 X-OVER (Crossover) .................................................... 27 Setting the Crossover ........................................................ 27 LIBRARY...................................................................... 28 Displaying the current library............................................ 28 Recalling a library.............................................................. 28 6 SP2060 Owner’s Manual LIMITER...................................................................... 29 SCENE ......................................................................... 29 About a scene..................................................................... 29 Recalling a scene ................................................................ 30 Storing a scene ................................................................... 31 Changing a scene title ........................................................ 31 Protecting a scene .............................................................. 31 Deleting a scene ................................................................. 32 UTILITY ...................................................................... 32 INPUT A/B LINK ............................................................ 32 User Lock .......................................................................... 33 Setting the Last Memory Resume ...................................... 33 Displaying the label ........................................................... 34 Displaying word clock ....................................................... 34 Checking the backup battery.............................................. 35 Displaying the firmware version......................................... 35 Initializing the SP2060 ...................................................... 35 Mute ............................................................................. 36 Network Settings ................................ 37 Setting a Device Group ................................................. Setting the IP Address ................................................... Setting the Master ID.................................................... Setting Link Mode ........................................................ Viewing the MAC Address ............................................ 37 37 38 38 39 References ....................................... 40 About Preset Libraries ................................................... 40 File name ........................................................................... 40 Subwoofer.......................................................................... 40 Limiter............................................................................... 40 Libraries for 1-way speaker processors ................................ 41 Libraries for 2-way speaker processors ................................ 42 Libraries for 3-way speaker processors ................................ 43 Display Messages........................................................... 44 Warning and error messages............................................... 44 Status messages .................................................................. 45 Troubleshooting ............................................................ General Specifications ................................................... Electrical Characteristics ................................................ Input/Output Characteristics ........................................ Connector Pin Assignment............................................ Dimensions ................................................................... Index ............................................................................. 45 46 46 47 48 49 50 Foreword Foreword Thank you for purchasing the Yamaha SP2060 Speaker Processor. In order to take full advantage of the features and performance provided by the SP2060, we urge you to read this owner’s manual thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference. You can check the firmware version of your SP2060 in the UTILITY display (see page 28). You can also download the latest firmware from the following Yamaha website. http://www.yamahaproaudio.com/ First plug the female-connector end of the AC cord into the [AC IN] socket on the rear panel of the SP2060, then plug the male plug into an appropriate AC mains outlet. Be sure to use the voltage specified for the device. The required voltage is printed on the name plate of the device. Turning the power on and off About DME Designer CAUTION DME Designer software enables you to control the SP2060 or DME series system from a connected computer. The DME Designer version 2.0 or later features this function. You can download DME Designer from the following Yamaha website. http://www.yamahaproaudio.com/ Precautions for Using a Rack-mounted SP2060 To prevent the initial power-on surge from generating a large noise spike or damaging your speaker system, turn devices on in the following order: audio sources, mixer (such as M7CL), SP2060, and finally power amplifiers. Reverse this order when turning power off. 1. Press the [POWER] switch to turn the power on to the SP2060. The SP2060 displays a message. 2. Press the [POWER] switch again to turn off NOTE The SP2060 remembers the scene settings when you turn off the power. When you turn on the power to the SP2060, it will start up with the same scene settings. You can also set up the SP2060 so that at the startup it will recall the scene selected before you turned off the power to the device (See page 33). CAUTION Fan kit Introduction to the SP2060 SpeakerProcessor SP2060 the power. If you install the SP2060 along with other SP2060 units or other devices in a poorly ventilated rack, the ambient temperature inside the rack may rise, resulting in inefficient performance. Be sure to install the SP2060 in a well-ventilated rack and make sure that the heat will be ventilated efficiently. If the temperature inside the rack is expected to rise above 40 degrees Celsius or 104 degrees Fahrenheit (or if the ambient temperature outside the rack is expected to rise above 30 degrees Celsius or 86 Fahrenheit), install a fan kit in the top row of the rack. The fan must provide airflow of 1.6m3/min or more and static pressure of 5mmH2O or more. The Controls and Connectors About the Firmware Version CAUTION Be sure to turn all devices OFF before connecting AC mains power. Panel Operation SP2060 Owner’s Manual (this document) AC power cord Rubber feet x 4 Connecting the AC power cord Do NOT turn off the power to the SP2060 while the unit is displaying the message “DO NOT TURN OFF!” at the bottom of the display, for example, while it is storing the scene. Otherwise, a malfunction may occur. Network Settings • • • Preparation References Accessories (Please make sure the following items are included in the package.) SP2060 SP2060 SP2060 Owner’s Manual 7 Foreword Introduction to the SP2060 Features Introduction to the SP2060 The Yamaha SP2060 Speaker Processor employs state-of-the-art digital technology and supports 96kHz audio. The SP2060 features two channel analog input connectors, an AES/EBU connector, and six channel analog output connectors. Since it includes preset settings for fixed installation speakers (such as the Yamaha IF/IS series), the SP2060 enables you to take the best advantage of a variety of speakers from 1-way through 6-way speakers. You can also control the SP2060 remotely using DME Designer application software. Glossary for the SP2060 This section explains terminology specific to the SP2060. Components & Parameters The Controls and Connectors The individual audio modules (equalizers, delays, and speaker processors that feature various speaker adjustment functions) are called “components.” Various settings included with each component are called “preset parameters.” Changing the parameter values for components enables you to control the effects of the audio process. Configuration A “configuration” is a complete set of components for constructing an optimum audio system that supports the connected speakers. See page 9. Each configuration determines the audio function(s) of the corresponding SP2060 unit. All parameter sets included with each component in a configuration are called “preset parameters.” Panel Operation Scene A combination of all configuration and preset parameter combinations is called a “scene.” A scene can be recalled from the panel of each SP2060 or via DME Designer. See page 29. Scene Configuration Preset Parameter Scene 1 Example: Limiter • Attack • Threshold • Release Scene 2 Network Settings Scene 99 Component Library References 8 All parameter sets included with each speaker processor component optimized for the connected speakers are called “libraries.” A library can be recalled from the panel of each SP2060 or via DME Designer. You can also create a library using DME Designer, then store it in an SP2060. SP2060 Owner’s Manual Configuration The SP2060 features 12 configurations. You can select one that suits the combination and configuration of the connected speakers. A configuration is stored as part of each preset scene (read-only scene) in scene memory slots #1 through #12, and can be recalled along with the corresponding scene. You can also edit parameters of a configuration, then store them in a user scene (readable and writable scene). Connection between the output port and output connector on each component is specified and fixed for each configuration. No.1. No.2. No.3. No.4. [3x2way [3x2way L [2x(2way+Sub) [2x(2way+Sub)L ] ] ] ] No.5. No.6. No.7. No.8. [2x2way+2xAux [2x2way+2xAuxL [2x3way [2x3way L ] ] ] ] No.9. [4way+2xAux No.10. [5way+Aux No.11. [6way No.12. [Multi Zone ] ] ] ] Introduction to the SP2060 Foreword Introduction to the SP2060 Controls three channel 2-way speakers. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] LOW LOW [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] The Controls and Connectors 3 x 2-way HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] LOW X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] LOW LOW X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA Panel Operation LOW [OUTPUT 6] HIGH Speaker’s input connector OUTPUT 1 2-way speaker (1) LOW OUTPUT 2 2-way speaker (1) HIGH OUTPUT 3 2-way speaker (2) LOW OUTPUT 4 2-way speaker (2) HIGH OUTPUT 5 2-way speaker (3) LOW OUTPUT 6 2-way speaker (3) HIGH References Output connector Network Settings HIGH 3 x 2-way Link Controls three channel 2-way speakers. All parameters for each component such as the Crossover, Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked. SP2060 Owner’s Manual 9 Introduction to the SP2060 Foreword 2 x (2-way + Sub) Controls two channel 2-way speakers and subwoofers. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] SUB WOOFER LOW Introduction to the SP2060 [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] LOW LOW X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] HIGH HIGH LIMIT [Library Data] X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] SUB WOOFER HIGH LIMIT [Library Data] The Controls and Connectors Output Delay Panel Operation Network Settings Output Level Output Mute Limiter DA [OUTPUT 5] LOW X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] HIGH HIGH Output connector Speaker’s input connector OUTPUT 1 Subwoofer (1) OUTPUT 2 2-way speaker (1) LOW OUTPUT 3 2-way speaker (1) HIGH OUTPUT 4 Subwoofer (2) OUTPUT 5 2-way speaker (2) LOW OUTPUT 6 2-way speaker (2) HIGH 2 x (2-way + Sub) Link Controls two channel 2-way speakers and subwoofers. All parameters for each component such as the Crossover, Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked. References 10 Output 6BandEQ with APF LOW SP2060 Owner’s Manual Foreword Introduction to the SP2060 2 x 2-way + 2 x Aux Controls two channel 2-way speakers and two channel subspeakers. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] LOW [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] LOW Introduction to the SP2060 LOW LOW X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] SUB SPEAKER LOW LIMIT [Library Data] X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] SUB SPEAKER Output connector Speaker’s input connector OUTPUT 1 2-way speaker (1) LOW OUTPUT 2 2-way speaker (1) HIGH OUTPUT 3 2-way speaker (2) LOW OUTPUT 4 2-way speaker (2) HIGH OUTPUT 5 1-way subspeaker (1) OUTPUT 6 1-way subspeaker (2) Panel Operation HIGH The Controls and Connectors X-Over References Controls two channel 2-way speakers and two channel subspeakers. All parameters for each component such as the Crossover, Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked. Network Settings 2 x 2-way + 2 x Aux Link SP2060 Owner’s Manual 11 Introduction to the SP2060 Foreword 2 x 3-way Controls two channel 3-way speakers. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] LOW LOW Introduction to the SP2060 [DIGITAL IN] + Input 8BandEQ Input Delay Input 8BandEQ Input Delay LIMIT X-Over [INPUT B] AD Input Level Input Mute Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] MID MID LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] LOW LOW LIMIT X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] The Controls and Connectors MID MID LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] HIGH HIGH Panel Operation Output connector Speaker’s input connector OUTPUT 1 3-way speaker (1) LOW OUTPUT 2 3-way speaker (1) MID OUTPUT 3 3-way speaker (1) HIGH OUTPUT 4 3-way speaker (2) LOW OUTPUT 5 3-way speaker (2) MID OUTPUT 6 3-way speaker (2) HIGH 2 x 3-way Link Network Settings Controls two channel 3-way speakers. All parameters for each component such as the Crossover, Delay, EQ, Level, and Limiter (excluding the Mute parameter) are linked. References 12 SP2060 Owner’s Manual Foreword Introduction to the SP2060 4 way +2 x Aux Controls one channel 4-way speaker and two channel subspeakers. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] LOW [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] LOW-MID LOW-MID X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] HIGH-MID Introduction to the SP2060 LOW HIGH-MID LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] HIGH HIGH LIMIT [Library Data] Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] SUB SPEAKER LOW LIMIT [Library Data] X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] SUB SPEAKER OUTPUT 1 4-way speaker (1) LOW OUTPUT 2 4-way speaker (1) LOW-MID OUTPUT 3 4-way speaker (1) HIGH-MID OUTPUT 4 4-way speaker (1) HIGH OUTPUT 5 1-way subspeaker (1) OUTPUT 6 1-way subspeaker (2) Network Settings Speaker’s input connector References Output connector Panel Operation HIGH The Controls and Connectors X-Over SP2060 Owner’s Manual 13 Introduction to the SP2060 Foreword 5-way + Aux Controls one channel 5-way speaker and one channel subspeaker. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] SUB-LOW SUB-LOW Introduction to the SP2060 [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] LOW LOW LIMIT X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] LOW-MID LOW-MID LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] HIGH-MID HIGH-MID LIMIT The Controls and Connectors Output Delay Panel Operation Output Level Output Mute Limiter DA [OUTPUT 5] HIGH LIMIT [Library Data] X-Over Output Delay HIGH Output connector Speaker’s input connector OUTPUT 1 5-way speaker (1) SUB-LOW OUTPUT 2 5-way speaker (1) LOW OUTPUT 3 5-way speaker (1) LOW-MID OUTPUT 4 5-way speaker (1) HIGH-MID OUTPUT 5 5-way speaker (1) HIGH OUTPUT 6 1-way subspeaker (1) Network Settings References 14 Output 6BandEQ with APF HIGH SP2060 Owner’s Manual Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] SUB SPEAKER Foreword Introduction to the SP2060 6-way Controls one channel 6-way speaker. LIMIT [Library Data] A SUM B [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] SUB-LOW [DIGITAL IN] [INPUT B] + AD Input Level Input Mute Input 8BandEQ Input Delay Input 8BandEQ Input Delay LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] LOW LOW LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] LOW-MID Introduction to the SP2060 SUB-LOW LOW-MID X-Over LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] MID MID LIMIT Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] HIGH-MID LIMIT Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] HIGH OUTPUT 1 6-way speaker (1) SUB-LOW OUTPUT 2 6-way speaker (1) LOW OUTPUT 3 6-way speaker (1) LOW-MID OUTPUT 4 6-way speaker (1) MID OUTPUT 5 6-way speaker (1) HIGH-MID OUTPUT 6 6-way speaker (1) HIGH Network Settings Speaker’s input connector References Output connector Panel Operation HIGH The Controls and Connectors Output Delay HIGH-MID SP2060 Owner’s Manual 15 Introduction to the SP2060 Foreword Multi Zone Outputs only the frequency components (by retrieving them from the input signals) that are suitable for the response characteristics of each speaker connected to each of six output connectors. LIMIT [Library Data] A SUM B Introduction to the SP2060 [INPUT A] AD Input Level Input Mute Input 8BandEQ Input Delay X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 1] HIGH LOW [DIGITAL IN] + Input 8BandEQ Input Delay LIMIT [Library Data] X-Over [INPUT B] AD Input Level Input Mute Input 8BandEQ Input Delay Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 2] HIGH HIGH LIMIT [Library Data] X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 3] HIGH LOW LIMIT [Library Data] X-Over Output Delay Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 4] HIGH HIGH LIMIT [Library Data] The Controls and Connectors X-Over Panel Operation Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 5] HIGH LIMIT [Library Data] X-Over Output Delay HIGH Output connector Speaker’s input connector OUTPUT 1 1-way speaker (1) OUTPUT 2 1-way speaker (2) OUTPUT 3 1-way speaker (3) OUTPUT 4 1-way speaker (4) OUTPUT 5 1-way speaker (5) OUTPUT 6 1-way speaker (6) Network Settings References 16 Output Delay LOW SP2060 Owner’s Manual Output 6BandEQ with APF Output Level Output Mute Limiter DA [OUTPUT 6] HIGH Foreword Introduction to the SP2060 System Examples This diagram indicates an example of a stereo 3-way system. The AES/EBU input connector on the SP2060 enables you to connect it directly to the AES/EBU output on a digital mixer. The configuration presets include 3 x 2-way, 2 x 3-way, 4-way + 2 x Aux, 5-way + Aux, and 6-way. (See page 9.) The SP2060 Routing function enables you to select IN A, IN B, or IN SUM (A+B) as component input. In this way, you can create a stereo, mono, or stereo mono (full-range stereo plus mono subwoofer) system very easily. You can also adjust the parameters or recall a scene from the front panel of the SP2060 or from a computer connected via Ethernet. Introduction to the SP2060 Speaker processing M7CL SP2060 1 XP7000 2 3 4 5 XP7000 Subwoofer XP7000 Bi-amp 2way Subwoofer Main speaker L 6 XP7000 Bi-amp 2way Main speaker R Panel Operation Left/Right (AES/EBU) * also Analog input available Network Settings AES/EBU The Controls and Connectors Ethernet L IN A IN A+B R IN B OUT 1 Sub L OUT 2 Low L OUT 3 Hi L OUT 4 Sub R OUT 5 Low R OUT 6 Hi R References Routing SP2060 Owner’s Manual 17 Introduction to the SP2060 Foreword Zone processing Introduction to the SP2060 This example is a stereo 3-zone system in which the SP2060 is used as a signal distributor, rather than a crossover. Adjusting the routing will enable you to create a monaural 6-zone system. You can adjust EQ, Delay, and Level for each output. This system is suitable for a facility that requires sound zoning, such as stores, restaurants, hotels, conference facilities, and exhibition halls, or for delay speakers in an SR system. MG16/4 The Controls and Connectors A 1 2 B 3 SP2060 4 5 XP7000 XP7000 6 XP7000 Panel Operation Network Settings L R L ZONE A R L ZONE B ZONE C Routing References L OUT 1 ZONE 1L OUT 2 ZONE 1R OUT 3 ZONE 2L OUT 4 ZONE 2R OUT 5 ZONE 3L OUT 6 ZONE 3R IN A+B R 18 IN A SP2060 Owner’s Manual R IN B Multiple SP2060 This example is a system that uses CobraNet™ for long-distance digital transfer between the control room and amp room. Audio signals from Yamaha PM5D digital mixing console, talkback mic signal, chime source, etc. are input to the DME64N. The output destination and level settings are specified via the Routing function. Furthermore, you can process output signals (EQ, Limiter, etc.) by adding an EQ component. The output from the DME64N is converted to CobraNet™ signals via the MY16-C, then transferred via the Ethernet cable to the NHB32-C located in the amp room. In the amp room, this signal is converted to the AES/EBU digital signal via the NHB32-C, then input to the SP2060, which, in turn, processes the signal using the Crossover, EQ, Delay, and Limiter to suit each speaker. The SP2060 control signal is also transferred to the amp room via the Ethernet cable. (Yamaha recommends that you use Giga-bit switching hubs.) Control Room Introduction to the SP2060 Foreword Introduction to the SP2060 DME64N Cascade HOME UTILITY LEVEL MUTE CANCEL ENTER MY16-C Switching Hub Switching Hub Ethernet AES/EBU CobraNet Amp Room Switching Hub Switching Hub Panel Operation SCENE Specifying the destination and processing (such as EQ) for the output signal The Controls and Connectors Talkback mic PM5D NHB32-C NETWORK HUB AND BRIDGE CONDUCT 88 ERROR LOCK SP2060 1 2 3 4 XP7000 6 1 XP7000 2 3 4 XM4180 5 6 XH200 References XP7000 5 SP2060 Network Settings LINK Main L Main R Mono Sub Stair Step Under Balcony Lobby/ Dressing Room SP2060 Owner’s Manual 19 Introduction to the SP2060 Foreword Routing L IN A IN A+B Introduction to the SP2060 R Low L OUT 2 Hi L OUT 3 Low R OUT 4 Hi R OUT 5 Mono Sub IN B OUT 6 The Controls and Connectors Panel Operation Network Settings References 20 OUT 1 SP2060 Owner’s Manual Stair Step (Mono) Under Balcony IN A IN A+B Lobby/ Dressing Room OUT 1 Under Balcony 1 OUT 2 Under Balcony 2 OUT 3 Under Balcony 3 OUT 4 Under Balcony 4 OUT 5 Lobby OUT 6 Dressing Room IN B Foreword The Controls and Connectors Front Panel % ^ Introduction to the SP2060 7 YES STORE RECALL A NO 8 !9 @) # 1 Display Displays the parameters selected for editing and information about the currently-recalled scene. Remove the transparent protective film that was applied prior to shipment from the factory. 2 [BACK/STORE] Key Selects the previous parameter. In the Scene display, it stores a selected scene. 3 [▲INC/YES]/[▼DEC/NO] Keys Confirm Yes or No to the change of parameter values or confirmation messages. 4 [NEXT/RECALL] Key Selects the next parameter. In the Library List display or Scene display, it recalls a selected library or scene respectively. 5 [LEVEL] Key Displays the input/output level settings. When these settings are displayed, the key LED lights up. 6 [DELAY] Key Displays the signal delay time settings. When these settings are displayed, the key LED lights up. 7 [EQ] Key Displays the EQ settings. When these settings are displayed, the key LED lights up. 8 [ROUTING] Key Displays the selection of the [INPUT] connectors and Output channel signal sources. When these settings are displayed, the key LED lights up. B 1 2 3 4 5 6 $ 9 [X-OVER] Key Displays the Crossover settings or library recall options. When these settings are displayed, the key LED lights up. ) [LIMITER] Key Displays the Limiter settings. When these settings are displayed, the key LED lights up. The Controls and Connectors 6 ! [SCENE] Key Displays scene store or recall options, or scene edit options. When these settings are displayed, the key LED lights up. @ [UTILITY] Key Displays the SP2060 Utility function settings. When these settings are displayed, the key LED lights up. # [MUTE] Key Displays the Mute settings. When these settings are displayed, the key LED lights up. At this time, each [SEL] key LED indicates the corresponding channel’s Mute On or Off and the [SEL] keys enable you to turn Mute On or Off for the corresponding channels. Holding down the [MUTE] key for two seconds or longer will turn the User Lock function On or Off. $ [SEL] Keys Select the corresponding channels for editing. The [SEL] key LED for each selected channel lights up. Panel Operation 5 Network Settings 2 3 4 % Meters Display the channel level meters and the Limiter indicators for Output channels. ^ [POWER ON/OFF] Key Turns mains power to the SP2060 on and off. SP2060 Owner’s Manual References 1 21 The Controls and Connectors Foreword Rear Panel ( º ¡ OUTPUT DIGITAL INPUT Introduction to the SP2060 AES/EBU & The Controls and Connectors Panel Operation 6 5 4 3 2 1 * & Ground Screw For maximum safety be sure to securely connect the SP2060 ground screw to an earth connection. The supplied power cable has a three-prong plug that will ground the unit when plugged into an appropriately grounded three-prong type AC mains outlet. If the AC outlet is not grounded, be sure to ground the unit by using this ground screw. Correct grounding will effectively eliminate hum noise and interference. * [AC IN] Connector Connect to the AC mains using the supplied AC power cord. First connect the power cord to the SP2060, then insert the power cord plug into an AC outlet. ( [NETWORK] Connector This is a 100Base-TX/10Base-T Ethernet connector for connection to a computer or other device in the network. NOTE • Use a CAT5 STP (Shielded Twisted Pair) cable for this connection to prevent electromagnetic interference. Since the SP2060 supports Auto MDI/MDI-X, it will automatically detect whether the connected cable is of the straight type or crossover type, and will configure itself to create the optimal connection. Therefore, you can use either a straight or crossover cable. • The maximum length of a cable between a switching hub and the SP2060 is 100 meters. Due to the quality of cables and switching hub performance, however, proper operation at the maximum length cannot be guaranteed in some cases. º [DIGITAL INPUT] Connector (AES/EBU) Connect an output of an AES/EBU (digital signal) compatible device to this XLR-3-31 connector. ¡ [OUTPUT] Connectors These XLR-3-32 balanced connectors output six channel analog audio signals. Connect them to the inputs on amplifiers. Network Settings ™ [INPUT] Connectors These XLR-3-31 balanced connectors input two channel analog audio signals. References 22 ™ SP2060 Owner’s Manual Basic Operation Foreword Panel Operation This section describes the function of the panel keys and related displays. change. To change the delay time, first press the [DELAY] key to switch to the Delay display. Refer to “The Controls and Connectors” on page 21 for information on the relationship between the parameters and keys. Some parameters will prompt you to confirm the operation to reflect the change in the value. In this case, a confirmation icon will appear on the display. Press the [NEXT] key to move the cursor to the icon, then press the [YES] key. A message prompts you to confirm. Press the [YES] key to confirm the operation. LEVEL OUT 1 ON/OFF = ON 2. Select a channel for which you wish to change the delay time. In this example, press the OUTPUT 1 [SEL] key. 3. Press the [NEXT] key repeatedly until the parameter you wish to change appears on the screen. In this example, select the Time parameter. OUT 1 TIME = You can view and adjust the Input and Output channel levels. Parameter Range INPUT A/B/SUM –∞, –138.00 through +10.00dB OUTPUT 1-6 –∞, –138.00 through +10.00dB 1. Press the [LEVEL] key to select the Level display. IN A LEVEL =-138.00dB The Controls and Connectors 1. Display the parameter setting you wish to Cursor Panel Operation SCENE EDIT 01:FOH(Event A) You can adjust the parameter settings, such as EQ, according to the speaker response or the acoustic environment of a particular venue. This section explains how to change the delay time for Output channel 1 as an example. Introduction to the SP2060 Confirmation icon Changing the parameter values 2.67ms The corresponding channel is selected. The [SEL] key LED for the selected channel lights up. parameter value. The parameter value on the screen changes accordingly. [▲ INC] key [▼ DEC] key Press the [▲ INC] key. The value increases. Hold down the [▲ INC] key. The value continues to increase as long as you hold down the key. While holding down the [▲ INC] key, press the [▼ DEC] key. The value continues to increase at a rate more rapid than when you hold down the [▲ INC] key. Press the [▼ DEC] key. The value decreases. Hold down the [▼ DEC] key. The value continues to decrease as long as you down the key. While holding down the [▼ DEC] key, press the [▲ INC] key. The value continues to decrease at a rate more rapid than when you hold down the [▼ DEC] key. IN B LEVEL =-138.00dB 3. Press the [▲INC]/[▼DEC] keys to adjust the input or output level. IN B LEVEL =-138.00dB References 4. Press the [▲ INC]/[▼ DEC] keys to change the Network Settings 2. Press the [SEL] key for the target channel. NOTE When INPUT A/B LINK is turned On, the parameters for channels A and B are linked and set to the same value automatically. SP2060 Owner’s Manual 23 Panel Operation Foreword DELAY EQ (Equalizer) You can set the signal delay time on each input and output channel. Set the On/Off parameter to On to delay the signal, and Off to bypass the delay. An EQ boosts or cuts the level of specified frequency ranges. The SP2060’s internal EQ processes input and output signals. Introduction to the SP2060 Parameter Range INPUT A/B/SUM 0–1300.00msec OUTPUT 1-6 0–500.00msec NO T E Channel SUM is a new channel created by applying the Level and Mute settings to Input channel A and B respectively, then adding both channel values. Input EQ You can apply eight-band EQ to Input channels A, B, and SUM. Set the On/Off parameter to On to apply EQ to the signal, and Off to not process the signal. You can set the following parameters for each band. 1. Press the [DELAY] key to select the Delay The Controls and Connectors Range Function BYPASS ON/OFF Sets the bypass for each frequency range to On or Off. Q 16.0–0.1 Specifies the width of each frequency range. FREQ (Frequency) 20.0Hz–20.0kHz Specifies the center frequency of each frequency range. GAIN –18dB through +18.00dB Sets the gain of the target frequency. display. IN A ON/OFF = OFF 2. Press the [SEL] key for the target channel. Panel Operation The [SEL] key LED of the selected channel lights up, and the corresponding channel name is displayed. Pressing the [SEL] keys for Input channels A and B simultaneously will turn on the [SEL] key LEDs and select channel SUM. You can select a type of filter for band 1 and band 8. All other bands utilize a fixed parametric EQ. Parameter Range Function TYPE PEQ L.SHELF 6dB/Oct L.SHELF 12dB/Oct H.SHELF 6dB/Oct H.SHELF 12dB/Oct HPF LPF Selects a type of filter. IN SUM ON/OFF = OFF 3. Press the [▲INC]/[▼DEC] keys to select On or Network Settings Off. IN SUM ON/OFF = ON 4. Press the [DELAY] or [NEXT] key to display the Time parameter. References IN B TIME = 130.00ms 5. Press the [▲INC]/[▼DEC] keys to adjust the delay time. IN B TIME = 24 Parameter SP2060 Owner’s Manual • PEQ This is a standard parametric equalizer. • L.SHELF(Low Shelving) Does not cut the lower frequency range, but cuts starting from the vicinity of the cutoff frequency toward the higher range at a specific rate. “6dB/Oct” and “12dB/Oct” stand for the cut amount per octave. • H.SHELF(High Shelving) Does not cut the higher frequency range, but cuts starting from the vicinity of the cutoff frequency toward the lower range at a specific rate. “6dB/Oct” and “12dB/Oct” stand for the cut amount per octave. • HPF This is a high pass filter (Q=0.7). The low frequency range is mildly cut (12dB/Oct), creating a slow curve. 120.00ms • LPF This is a low pass filter (Q=0.7). The high frequency range is mildly cut (12dB/Oct), creating a slow curve. 2. Press the [SEL] key for the target channel. IN SUM ON/OFF = You can set the following parameters for each band. Parameter Range Function BYPASS ON/OFF Sets the bypass for each frequency range to On or Off. TYPE PEQ L.SHELF 6dB/Oct L.SHELF 12dB/Oct H.SHELF 6dB/Oct H.SHELF 12dB/Oct HPF LPF APF 1st APF 2nd Horn Selects a type of filter. Q 63.0–0.1 Specifies the width of each frequency range. FREQ (Frequency) 20.0Hz–20.0kHz Specifies the frequency of each band. GAIN –18dB through +18.00dB Sets the gain of the target frequency. ON 3. Press the [EQ], [BACK] or [NEXT] key to display the On/Off parameter. 4. Press the [▲INC] key to set the On/Off parameter to On to apply EQ to the signal. Press the [▼DEC] key to set the On/Off parameter to Off to not process the signal. 5. Press the [BACK] or [NEXT] key to select the Bypass, Type, Q, Freq, or Gain parameter. IN SUM BAND 2 Q = 0.125 6. Pressing the [EQ] key repeatedly will scroll the bands from 1 through 8. IN SUM BAND 3 Q = 0.125 7. Press the [▲INC]/[▼DEC] keys to select the value. • APF (All Pass Filter) This filter passes all ranges of frequency, but changes only the phase. It is used to align the phase in the crossover range. APF 1st rotates the phase by 0 through 180 degrees, and APF 2nd rotates the phase by 0 through 360 degrees. APF 2nd requires the Q setting. • Horn A horn speaker typically features a roll-off in the higher frequency component. Horn EQ corrects this characteristics. For this purpose, the gain is limited to 0dB or higher, and the frequency to 500Hz or higher. References The [SEL] key LED of the selected channel lights up, and the corresponding channel name is displayed. Pressing the [SEL] keys for channels A and B will turn on the [SEL] key LEDs and select channel SUM. Introduction to the SP2060 ON You can apply a 6-band EQ to Output channels 1–6. Set the On/Off parameter to On to apply EQ to the signal, and Off to not process the signal. The parameters are the same as for the input EQ. The Controls and Connectors IN A ON/OFF = Output EQ Panel Operation EQ display. Network Settings 1. Press the [EQ] key repeatedly to select the Foreword Panel Operation SP2060 Owner’s Manual 25 Panel Operation Foreword ROUTING Output routing Introduction to the SP2060 Input routing You can route Input channel A, B, and SUM signals to the Crossover input. You can select either analog or digital input signals. This selection links to the word clock master setting. You can also route the left channel of an input signal received at the [INPUT A] or [DIGITAL IN] connector to both Input channels A and B. The following three channels are available: • IN A • IN SUM • IN B Option Input Signal Selection ANA A/B A signal at the [INPUT A] connector is routed to channel A, and a signal at the [INPUT B] connector to channel B. The Controls and Connectors ANA A/A A signal at the [INPUT A] connector is routed to channels A and B. DIG L/R A left channel signal is routed to channel A, and a right channel signal to channel B. DIG L/L Word Clock Master Internal clock: 96kHz Routing display. OUT 2 SOURCE = IN A 2. Press the [SEL] key for the target Output Incoming AES/ EBU signal A left channel signal is routed to channels A and B. channel. The [SEL] key LED for the selected channel lights up. The [SEL] key LED for each channel that shares the same component flashes. The selected channel name appears on the display. Panel Operation OUT 4 SOURCE = IN A HINT You can check the word clock status on the Utility display. See page 34. 3. Press the [▲INC]/[▼DEC] keys to select an input source to be routed to the Crossover. 1. Press the [ROUTING] key to select the Routing display. Network Settings INPUT SELECT SOURCE = ANA A/B 2. Press the [▲INC]/[▼DEC] keys to select an input signal source. INPUT SELECT SOURCE = ANA A/A References 26 1. Press the [ROUTING] key to select the NO T E Signals are muted while they are switched between analog and digital to avoid noise. SP2060 Owner’s Manual OUT 4 SOURCE = IN SUM Function TYPE Thru 6dB/Oct 12dB/Oct AdjustGc 12dB/Oct Butrwrth 12dB/Oct Bessel 12dB/Oct Linkwitz 18dB/Oct AdjustGc 18dB/Oct Butrwrth 18dB/Oct Bessel 24dB/Oct AdjustGc 24dB/Oct Butrwrth 24dB/Oct Bessel 24dB/Oct Linkwitz 36dB/Oct AdjustGc 36dB/Oct Butrwrth 36dB/Oct Bessel 48dB/Oct AdjustGc 48dB/Oct Butrwrth 48dB/Oct Bessel 48dB/Oct Linkwitz Selects an attenuation amount per octave, and a type of filter. If you select “Thru,” no filter will be applied. FREQ (Frequency) 20.0Hz–20.0kHz Specifies the cutoff frequency of the high pass filter. Gc –6dB through +6dB You can set the gain for the cutoff frequency (Gc) when you select “AdjustGc (Adjustable Gc)” for the Type parameter. TYPE Thru 6dB/Oct 12dB/Oct AdjustGc 12dB/Oct Butrwrth 12dB/Oct Bessel 12dB/Oct Linkwitz 18dB/Oct AdjustGc 18dB/Oct Butrwrth 18dB/Oct Bessel 24dB/Oct AdjustGc 24dB/Oct Butrwrth 24dB/Oct Bessel 24dB/Oct Linkwitz 36dB/Oct AdjustGc 36dB/Oct Butrwrth 36dB/Oct Bessel 48dB/Oct AdjustGc 48dB/Oct Butrwrth 48dB/Oct Bessel 48dB/Oct Linkwitz Selects an attenuation amount per octave, and a type of filter. If you select “Thru,” no filter will be applied. FREQ (Frequency) 20.0Hz–20.0kHz Specifies the cutoff frequency of the low pass filter. –6dB through +6dB You can set the gain for the cutoff frequency (Gc) when you select “AdjustGc (Adjustable Gc)” for the Type parameter. Input signals can be divided into specified frequency ranges to suit speaker response characteristics prior to output. The number of division is determined to 1-way through 6way, depending on the selected component. Parameter LEVEL POLARITY Range Function –∞, –138.00 through +10.00dB Adjusts the level of the signal input to the Crossover. The same Level setting is used for the output channels of a component. NORMAL INVERTED The output signal phase for each frequency range is inverted. HPF HPF Refer to Step 4. LPF 1. Press the [X-OVER] key repeatedly until the XOver display appears on the screen. OUT 1 FREQ LPF = 20.0kHz 2. Press the [SEL] key for the target Output channel. The [SEL] key LED of the selected channel lights up, and the corresponding channel name is displayed. OUT 3 FREQ LPF = 20.0kHz 3. Press the [NEXT]/[BACK] keys to select a parameter to edit. OUT 3 LPF TYPE =24AdjustGc LPF Gc SP2060 Owner’s Manual Introduction to the SP2060 Range The Controls and Connectors Parameter Setting the Crossover Panel Operation parameter value. Network Settings 4. Press the [▲INC]/[▼DEC] keys to set the References X-OVER (Crossover) Foreword Panel Operation 27 Panel Operation Foreword NO T E LIBRARY • The type names are abbreviated on the SP2060 screen. For example, “24dB/Oct Bessel” is displayed as “24Bessel.” • Gc page is displayed if you select “Adjust Gc” for the Type parameter. Using libraries facilitates the recall of optimal speaker settings. Up to 60 libraries are available for each component via the DME Designer application. Introduction to the SP2060 • Thru No filter is applied. The original characteristics are kept with no attenuation for all frequency ranges. • AdjustGc (Adjustable Gc) Filters with an Adjustable Gc enable you to adjust the gain at the cutoff frequency in the range of –6dB through +6dB. With Gc set to –3dB, the filter is practically a Butterworth filter. And with Gc set to –6dB, the filter is practically a Linkwitz-Riley filter. The Controls and Connectors • Butrwrth (Butterworth) This filter is the most common type of filter. It has a flat pass band and a –3dB gain at the cutoff frequency. • Bessel This filter focuses on the phase characteristics. Although it has a more gradual roll-off than a Butterworth filter, it will pass a square wave without causing ringing. Panel Operation • Linkwitz (Linkwitz-Riley) This filter features the square of the second order. When the output signal from its LPF and HPF are combined, the gain over the entire range is +/–0dB. It has a flat pass band and a –6dB gain at the cutoff frequency. Displaying the current library Pressing the [X-OVER] key repeatedly will select the Current Library display, Library List display, or X-Over display, in this order. The title of the library most recently recalled for each component will be displayed. CURRENT LIBRARY IF2112/95 NOTE Libraries cannot be displayed or recalled for Input channels. If you press an Input channel [SEL] key, a message appears. Recalling a library Follow the steps below to recall a library: 1. Press the [X-OVER] key repeatedly until the Library List display appears on the screen. LIBRARY LIST IF2112/64 Network Settings 2. Press the [SEL] key of an Output channel for a component for which you wish to recall a library. 3. Press the [▲INC]/[▼DEC] keys to select a library. LIBRARY LIST IF2112/64 References 4. Press the [NEXT/RECALL] key. A confirmation message will appear. LIBRARY RECALL ARE YOU SURE? 28 SP2060 Owner’s Manual The library is recalled and the unit returns to the Library List display. 1. Press the [LIMITER] key to select the Limiter display. OUT 1 ON/OFF = LIBRARY LIST IF2112/95 To cancel the recall operation, press the [NO] key, instead of the [YES] key. The unit returns to the Library List display. ON 2. Press the [SEL] key for the target channel. The [SEL] key LED of the selected channel lights up, and the corresponding channel name is displayed. HIN T OUT 4 ON/OFF = You can use the library data for speaker processor components for DME64N/24N that you have created using DME Designer. Introduction to the SP2060 5. To confirm the selection, press the [YES] key. Foreword Panel Operation ON display the On/Off parameter. Range Function THRESHOLD –54 through 0dB Sets the threshold value. ATTACK FAST MID SLOW MANUAL (0– 120.0ms) Sets the attack time. RELEASE FAST MID SLOW MANUAL 44.1kHz: 6ms–46s, 48kHz: 5ms–42.3s, 88.2kHz: 3ms–23s, 96kHz: 3ms–21.1s Sets the release time. If you select Fast, Mid, or Slow, the unit automatically sets the optimum value based on the maximum wave length of audio input to the Limiter. NOT E • You can set the attack time only when “Manual” is selected for the Attack parameter. • You can set the release time only when “Manual” is selected for the Release parameter. parameter to On to apply the Limiter to the signal. Press the [▼DEC] key to set the On/ Off parameter to Off to cancel the Limiter. 5. Press the [NEXT]/[BACK] keys to select a parameter to edit. OUT 4 THRESHOLD= -54dB 6. Press the [▲INC]/[▼DEC] keys to set the parameter value. Panel Operation Parameter 4. Press the [▲INC] key to set the On/Off SCENE About a scene The SP2060 enables you to store various parameter settings as part of scene, and recall them via the front panel or remotely from DME Designer. You can store the following settings in a scene: • Configuration • Routing • Parameter sets of all components • Scene titles • Scene protection status • INPUT A/B LINK • The title of the library most recently recalled Network Settings You can set up the Output channel limiter. The Limiter precludes signal levels higher than a specified threshold to avoid speaker damage from excess output level. References LIMITER The Controls and Connectors 3. Press the [LIMITER], [BACK] or [NEXT] key to H INT You can protect a scene to forbid overwriting. SP2060 Owner’s Manual 29 Panel Operation Foreword Scenes are stored in the preset area and user area. Recalling a scene Preset area There is a preset scene for each of 12 configurations. These scenes are numbered 1 through 12. Each scene title has the same name as the corresponding configuration title. Introduction to the SP2060 No.1. [3x2way No.2. [3x2way L No.3. [2x(2way+Sub) No.4. [2x(2way+Sub)L No.5. [2x2way+2xAux No.6. [2x2way+2xAux L No.7. [2x3way No.8. [2x3way L No.9. [4way+2xAux No.10. [5way+Aux No.11. [6way No.12. [Multi Zone H INT You can also recall a scene using the DME Designer application. ] ] ] ] ] ] ] ] ] ] ] ] NOTE If recalling a scene has changed the configuration, audio output will be muted momentarily. 1. Press the [SCENE] key to select the Scene Selection display. The Controls and Connectors User area The user area can accommodate up to 87 user scenes, which you can store and recall at your discretion. These scenes are numbered 13 through 99. Scene indication Scene number Scene property Follow the steps below to recall a scene (1–99): Title 25:FOH(Event A) [2x(2way+SUB)L] 2. Press the [▲INC]/[▼DEC] keys to select a scene number. While you are selecting a scene, the scene number and title will be flashing. NOTE Panel Operation 25:FOH(Event A) [2x(2way+SUB)L] If no data is included in the currently-selected scene, the message “No Scene” appears. Configuration title The upper row indicates a scene number, property, and title. The bottom row indicates the configuration title. 3. Press the [RECALL] key. A confirmation message will appear. Scene property includes the following types: 33:RECALL ARE YOU SURE? Network Settings Preset scene Protected user scene 4. Press the [YES] key. Unprotected user scene NO T E After you recall a scene, if you edit a parameter, an appears in the lower right corner on the screen. References 30 icon The scene is recalled and its number becomes the current scene number. To cancel the recall operation, press the [NO] key, instead of the [YES] key. The unit returns to the Scene Selection display. NOTE If the selected scene contains no data or User Lock is turned on for the scene, a status message appears. SP2060 Owner’s Manual You can also store a scene using the DME Designer application. 1. Press the [SCENE] key to select the Scene Selection display. 25:FOH(Event A) [2x(2way+SUB)L] 2. Press the [▲INC]/[▼DEC] keys to select a scene number. 3. Press the [BACK/STORE] key. A confirmation message will appear. 72:STORE ARE YOU SURE? H INT Holding down the [▲INC]/[▼DEC] keys will increase the speed at which the characters scroll. 4. When you finish editing the title, press the [NEXT] key repeatedly to move the cursor to the icon, then press the [YES] key. A confirmation message will appear. SCENE EDIT ARE YOU SURE? 5. To confirm the edit, press the [YES] key. The title is changed and the unit returns to the Scene Edit display. Protecting a scene Follow the steps below to protect a scene: 1. Press the [SCENE] key repeatedly until the 4. Press the [YES] key. The scene is stored and its number becomes the current scene number. To cancel the store operation, press the [NO] key, instead of the [YES] key. The unit returns to the Scene Selection display. Introduction to the SP2060 HIN T character. The Controls and Connectors Follow the steps below to store a scene (13–99) to the user area: 3. Press the [▲INC]/[▼DEC] keys to change the Scene Edit display appears on the screen. SCENE EDIT 73:FOH(Event A) Panel Operation Storing a scene Foreword Panel Operation 2. Press the [▲INC]/[▼DEC] keys to select a the scene property icon. SCENE EDIT 73:FOH(Event A) NOT E You cannot change the title of any protected User scenes. 1. Press the [SCENE] key repeatedly until the Scene Edit display appears on the screen. SCENE EDIT 73:FOH(Event A) 4. Press the [▲INC]/[▼DEC] keys to turn protection on or off. The protection icon flashes. SCENE EDIT 73 FOH(Event A) References Follow the steps below to change the title (up to 13 characters) of the scene stored for the current scene number: 3. Press the [NEXT] key to move the cursor to Network Settings scene number. Changing a scene title 2. Press the [BACK]/[NEXT] keys to move the cursor to a character you want to edit. SCENE EDIT 73:FOH(Event A) SP2060 Owner’s Manual 31 Panel Operation Foreword 5. Press the [NEXT] key repeatedly to move the cursor to the icon, then press the [YES] key. A confirmation message will appear. SCENE EDIT ARE YOU SURE? Introduction to the SP2060 6. To confirm the edit, press the [YES] key. The unit reflects the edit and returns to the Scene Edit display. HINT You can turn protection on and off from the DME Designer application. UTILITY The Utility function enables you to view the word clock status and make network settings. See page 37 for more information on making network settings. INPUT A/B LINK Follow the steps below to link the Input channel A and B parameters: When INPUT A/B LINK is turned On, the parameters for channel A and B are linked and set to the same value automatically. NOTE The channel SUM parameters cannot be linked. The Controls and Connectors Follow the steps below to delete a scene: The following components will be linked: • INPUT LEVEL • INPUT EQ • INPUT DELAY 1. Press the [SCENE] key repeatedly until the 1. Press the [UTILITY] key to select the Utility Deleting a scene Scene Delete display appears on the screen. Panel Operation SCENE DELETE 72:FOH(Event A) display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the INPUT A/B LINK page appears. 2. Press the [▲INC]/[▼DEC] keys to select a scene to delete. INPUT A/B LINK OFF 3. Press the [NEXT] key to move the cursor to Network Settings the icon, then press the [YES] key. A confirmation message will appear. 3. Press the [▲INC] key to link the parameters. “ON” flashes on the screen. SCENE DELETE ARE YOU SURE? INPUT A/B LINK ON 4. To confirm the operation, press the [YES] key. The operation is executed and the unit returns to the Scene Delete display. 4. Press the [NEXT] key to move the cursor to the icon. References NO T E You cannot delete preset scenes, protected scenes, and current scene. INPUT A/B LINK ON 5. Press the [YES] key. A confirmation message will appear. INPUT A/B LINK ARE YOU SURE? 32 SP2060 Owner’s Manual The flashing “ON” (or “OFF”) lights up steadily, and the cursor returns to the “ON (or OFF)” position. 4. Press the [NEXT] key to move the cursor to the USER LOCK ON INPUT A/B LINK ARE YOU SURE? To cancel the operation and return to the original setting, press the [NO] key. icon. 5. Press the [YES] key. A confirmation message will appear. NOT E USER LOCK ARE YOU SURE? If you set INPUT A/B LINK to “ON,” the linked parameters for channel A will be copied to channel B parameters. Introduction to the SP2060 6. To confirm the operation, press the [YES] key. Foreword Panel Operation 6. To confirm the operation, press the [YES] key. User Lock NOT E H INT • A short cut to turn on the User Lock function is to hold down the [MUTE] key for two seconds or longer. • A short cut to turn off the User Lock function is to hold down the [MUTE] key for two seconds or longer. Setting the Last Memory Resume • You can mute or unmute, or cancel User Lock even if the User Lock function is turned on. • The User Lock function is effective only for the panel controls on the SP2060, and does not affect any control signals from external devices. 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the User Lock page appears. USER LOCK OFF 3. Press the [▲INC] key to turn User Lock on. To cancel User Lock, press the [▼DEC] key. “ON” flashes on the screen. You can select whether at the startup the SP2060 recalls the scene selected before you turned off the power to the device, or it starts up with the same status as when it was shut down last time. The default setting is “ON.” OFF: At the startup, the SP2060 will recall the scene selected before you turned off the power to the device. ON: The SP2060 will start up with the same status as when it was shut down last time. 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. Panel Operation Editing the parameters Recalling and storing a scene Changing a scene title Changing the scene protection status Recalling a library Network Settings * * * * * Panel Locked 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the Last Memory Resume page appears. LAST MEM. RESUME ON References Parameter settings can be “locked” temporarily to prevent accidental mis-operation. This function is useful to avoid unintentional operations or to prevent others from operating the panel controls. The following operations are the User Lock target. The Controls and Connectors A status message appears, and User Lock becomes active. USER LOCK ON SP2060 Owner’s Manual 33 Panel Operation Foreword 3. Press the [▲INC] key so that the SP2060 will start up with the same status as when it was shut down last time. Press the [▼DEC] key so that at the startup the SP2060 will recall the scene selected before you turned off the power to the device. “ON” flashes on the screen. Introduction to the SP2060 LAST MEM. RESUME ON 4. Press the [NEXT] key to move the cursor to the icon. The Controls and Connectors LAST MEM. RESUME ON 5. Press the [YES] key. A confirmation message will appear. Displaying word clock Word clock changes in accordance with input routing settings. You can view the current word clock status on the display. One of the following six word clock sources will be displayed: For analog input signals: The internal clock (Fs=96kHz) is used. • INT:96kHz : Internal clock (96kHz) For digital input signals: The SP2060 synchronizes to an external clock (input at the AES/EBU connector). • EXT:44.1kHz : External clock (44.1kHz) • EXT:48kHz : External clock (48kHz) • EXT:88.2kHz : External clock (88.2kHz) • EXT:96kHz : External clock (96kHz) • EXT:UNLOCK : Unlock to external clock 1. Press the [UTILITY] key to select the Utility LAST MEM. RESUME ARE YOU SURE? display. The most recently used Utility display page will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key Panel Operation 6. To confirm the operation, press the [YES] key. The selection is applied and the unit returns to the Last Memory Resume page. Displaying the label Network Settings 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the Label page appears. The unit displays the label you created on DME Designer. References LABEL [FoH L ] NO T E • You cannot edit the label on the SP2060. • Up to 14 characters from the top can be displayed. SP2060 Owner’s Manual W.CLOCK [INT: 96kHz] NOTE You can view the label for the SP2060 that you have set on DME Designer. 34 repeatedly until the W. Clock page appears. If no signal exists at the [DIGITAL INPUT] connector while digital input is selected, or if the SP2060 cannot somehow lock to the incoming signal, an error message appears. Checking the backup battery Initializing the SP2060 Follow the steps below to check the internal backup battery status: Follow the steps below to initialize the internal memory: You can select one of the following initialization types: 1. Press the [UTILITY] key to select the Utility * display. The most recently used Utility display will appear. * ] The remaining battery charge is displayed as follows: [OK ] Plenty of charge [Low Battery] Charge is getting low. [No Battery ] Memory data may be lost. Or, no battery is installed. CAUTION “Low Battery” or “No Battery” will appear when the battery charge is getting low. In this case, save the data to an external device (such as a computer) immediately, then ask the Yamaha dealer to replace the backup battery. CAUTION When the internal memory is initialized, all data stored in the memory will be lost. Use caution when you execute this function. 1. Turn off the power to the SP2060. 2. Turn on the power to the SP2060 while holding down the [BACK/STORE] key. The Initialization display appears. INITIALIZE FACTORY SETUP 3. Press the [▲INC]/[▼DEC] keys to select a type of initialization. HIN T Displaying the firmware version Follow the steps below to view the current firmware version number: 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display page will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the Version page appears. The page indicates the current firmware version number. NOTE To cancel the initialization operation, select “Exit” and confirm the cancellation. Alternatively, simply turn off the power to the SP2060. 4. Press the [NEXT] key to move the cursor to the icon, then press the [YES] key. The Initialization operation starts. During initialization, the following status message appears: INITIALIZE EXECUTING.. When initialization is completed, the SP2060 displays the following status message, then automatically restarts. References If there is any issue with the backup battery, the SP2060 displays “Low Battery,” “Critical Battery,” or “No Battery” when you turn on the power to the unit. INITIALIZE COMPLETED! VERSION The Controls and Connectors BATTERY [OK Panel Operation repeatedly until the Battery page appears. * Network Settings 2. Press the [UTILITY], [NEXT] or [BACK] key Initializing the current scene backup [CURRENT BACKUP] Initializing all user settings (excluding the libraries) to the factory settings [WITHOUT LIB.] Initializing all settings to the factory settings [FACTORY SETUP] Introduction to the SP2060 Foreword Panel Operation [V1.00] You can update the SP2060 firmware via DME Designer. Refer to the DME Designer Owner’s Manual for details. You can also download the latest firmware from the following Yamaha website. http://www.yamahaproaudio.com/ SP2060 Owner’s Manual 35 Panel Operation Foreword Mute When Mute is on, the corresponding Input or Output channel audio is muted. You can determine the channel Mute status by checking the corresponding channel [MUTE] key LED. Introduction to the SP2060 • • MUTE OFF : Dark MUTE ON : Illuminated 1. Press the [MUTE] key to select the Mute display. NOW SELECT KEYS ACT "MUTE" -> The Controls and Connectors 2. Press the [SEL] key for the target channel. The channel audio is muted and the [MUTE] key LED lights up. Pressing the channel [SEL] key repeatedly toggles between Mute on and off. A Panel Operation 1 NO T E You can mute or unmute even if the User Lock function is turned on Network Settings References 36 B SP2060 Owner’s Manual Setting the IP Address IP ADDRESS 192.168.000.003 When connecting a computer to an SP2060 via Ethernet, you must install the appropriate DME-N Network driver on the computer. You can download the DME-N Network driver from the Yamaha website. Network address Host address NOTE Setting a Device Group A “device group” is a group of multiple SP2060 units that can be operated in sync via DME Designer. Follow the steps below to assign each SP2060 in a device group as master or slave. Each device group must have one master. All other devices in the group are assigned as slave. 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the Device Group page appears. DEVICE GROUP MASTER • Subnet mask is fixed at 255.255.255.0. • Gateway address is the same network address as the IP address. The host address is automatically set to 254. Each group of digits between periods in an IP address is called “octet.” These groups of digits are called “1st octet,” “2nd octet,” etc., starting from the left-most digit group. You cannot specify 0, 127, and 223 through 255 for the 1st octet of the network address. You can specify the following range of values for the 4th octet. Master : 2–253 Slave : 3–253 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the IP Address page appears. The Controls and Connectors NOT E Introduction to the SP2060 Follow the steps below to set the IP address for each SP2060. Panel Operation This section describes the network-related settings on the SP2060 that you need to make when you connect a computer or other external device to the SP2060 [NETWORK] connector. Foreword Network Settings 3. Press the [▲INC]/[▼DEC] keys to select 4. Press the [NEXT] key to move the cursor to the icon, then press the [YES] key. A confirmation message will appear. DEVICE GROUP ARE YOU SURE? 3. Press the [NEXT]/[BACK] keys to move the cursor to an octet you want to specify. IP ADDRESS 192.168.000.003 4. Press the [▲INC]/[▼DEC] keys to change the value. When you change the value, the octet flashes. 5. Press the [NEXT] key to move the cursor to 5. To confirm the setting, press the [YES] key. The selection is applied and the unit returns to the Device Group page. Network Settings DEVICE GROUP SLAVE IP ADDRESS 192.168.000.002 References “MASTER” or “SLAVE.” When you change the setting, the parameter setting flashes. the icon, then press the [YES] key. A confirmation message will appear. IP ADDRESS ARE YOU SURE? SP2060 Owner’s Manual 37 Network Settings Foreword 6. To confirm the setting, press the [YES] key. The setting is applied and the unit returns to the IP Address page. Setting the Master ID Introduction to the SP2060 The SP2060 units that are assigned as slaves in a device group follow the master SP2060 in the same group via communication. Follow the steps below to set the master ID on the slave SP2060 units. Use the 4th octet of the IP address of the master unit as the Master ID parameter value. NO T E This parameter can be set from 2 through 253. The Controls and Connectors 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. Follow the steps below to select 100Base-TX or 10Base-T for the [NETWORK] connector speed. 100Base-TX The [NETWORK] connector basically operates as 100BaseTX, but automatically switches to 10Base-T if the network environment is not compatible with 100Base-TX. 10Base-T The [NETWORK] connector is compatible with 10Base-T operation. 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key repeatedly until the Link Mode page appears. 2. Press the [UTILITY], [NEXT] or [BACK] key LINK MODE 100BASE-TX repeatedly until the Master ID page appears. MASTER ID 253 Panel Operation 3. Press the [▲INC]/[▼DEC] keys to set the value to the same number as the 4th octet of the master SP2060 IP address. 3. Press the [▲INC] key to select 100Base-TX, and the [▼DEC] key to select 10Base-T. When you change the setting, the parameter setting flashes. LINK MODE 10BASE-T 4. Press the [NEXT] key to move the cursor to the icon, then press the [YES] key. A confirmation message will appear. Network Settings MASTER ID ARE YOU SURE? 4. Press the [NEXT] key to move the cursor to the icon, then press the [YES] key. A confirmation message will appear. LINK MODE ARE YOU SURE? 5. To confirm the setting, press the [YES] key. The setting is applied and the unit returns to the Master ID page. To cancel the operation and return to the original setting, press the [NO] key, instead of the [YES] key. References 38 Setting Link Mode 5. To confirm the setting, press the [YES] key. The unit reflects the edit and returns to the Link Mode page. NOTE Depending on the specifications of the connected network devices (such as a switching hub, router, etc.), changing Link Mode may cause the SP2060 to be unable to reconnect to the network. In this case, turn the power to the SP2060 off and then on. The SP2060 will reconnect to the network. SP2060 Owner’s Manual Foreword Network Settings Viewing the MAC Address Follow the steps below to view the SP2060 MAC address: NOT E Introduction to the SP2060 In some cases, you may not need to set the MAC address via the DME-N Network driver when the SP2060 is communicating with DME Designer. 1. Press the [UTILITY] key to select the Utility display. The most recently used Utility display will appear. 2. Press the [UTILITY], [NEXT] or [BACK] key The Controls and Connectors repeatedly until the MAC Address page appears. The bottom row indicates the MAC address. References Network Settings Panel Operation MAC ADDRESS [00A0DE250123] SP2060 Owner’s Manual 39 Foreword References About Preset Libraries File name Introduction to the SP2060 LIBRARY LIST IF211264_pa_sub Model name The Controls and Connectors • • • • • Drive Subwoofer usage mode LIBRARY LIST IF2112AS_bi_moni Model name Drive Floor monitor mode pa........................ Passive mode* bi ........................ Bi-amp mode tri........................ Tri-amp mode sub...................... Combining with a subwoofer** moni ................... For a floor monitor * Yamaha Installation Series speakers are designed to be used without a speaker processor when Passive mode is selected. However, using a speaker processor will improve the performance significantly. ** This setting is for full-range speakers. Subwoofer settings are not included. Subwoofer • Panel Operation • • • “_sub” settings for 12-inch or 15-inch 3-way full-range speakers are designed for a combination with IS1118, IS1215, or IS1218. The IS1118, IS1215, and IS1218 settings are specified for a monaural subwoofer usage. The full-range and subwoofer level balance varies depending on the number of speakers used, installation conditions, and applications. If the full-range speaker baffle and subwoofer baffle are aligned, the speaker polarity will be positive and inphase. Depending on the installation conditions of the subwoofers, you might achieve better results if the subwoofer phase is inverted. Network Settings Limiter • • • The default value of the threshold level has been specified based on the maximum analog output level of +24dBu and amp voltage gain of 26dB (which corresponds to “ATT –6dB” if you are using a Yamaha PC series amplifier that features a voltage gain of 32dB). If you are not using the output levels referenced above, change the threshold level. For example, if you are using an amplifier with a voltage gain of 30dB, lower the threshold level by 4dB. Attack time and Release time are both set to “Mid.” The Limiter may not completely protect the speakers. Use the Limiter if they suit your environment. References 40 SP2060 Owner’s Manual Foreword References Libraries for 1-way speaker processors NO T E Target speakers Library name Meaning IS1118 and IS1218 IS1118_IS1218 This setting can be shared by IS1118 and IS1218 when IF2112 (M), IF2115 (M) or IF3115 is combined. IS1215 IS1215 This setting is for IS1215 when IF2112 (M), IF2115 (M) or IF3115 is combined. Standard subwoofer Sub_5inch&8inch This LPF setting can be shared by standard subwoofers when IF2205, IF2108, or IF2208 is combined. The following table shows the settings for Yamaha Installation Series speakers (full-range, passive mode). – – IF2205_sub ✓ – IF2108 – – IF2108_sub ✓ – IF2108_moni – ✓ IF2208 – – IF2208_sub ✓ – IF2208_moni – ✓ IF2112AS_pa – – IF2112/AS IF2112AS_pa_sub ✓ – IF2112AS_pa_moni – ✓ IF211264_pa – – IF211264_pa_sub ✓ – IF211295_pa – – IF211295_pa_sub ✓ – IF211299_pa – – IF211299_pa_sub ✓ – IF2112M64_pa – – IF2112M64_pa_sub ✓ – IF2112M95_pa – – IF2112M95_pa_sub ✓ – IF2112M99_pa – – IF2112M99_pa_sub ✓ – IF2115AS_pa – – IF2115AS_pa_sub ✓ – IF2115AS_pa_moni – ✓ IF211564_pa – – IF211564_pa ✓ – IF2112/64 IF2112/95 IF2112/99 IF2112M/64 IF2112M/95 IF2112M/99 IF2115/AS IF2115/64 Panel Operation IF2208 For a floor monitor IF2205 IF2205 IF2108 Subwoofer usage* Network Settings Library name References Target speakers The Controls and Connectors The following table shows typical subwoofer settings when it is combined with Yamaha Installation Series speakers. Introduction to the SP2060 These libraries also apply to 2-way speakers that are used in passive mode. SP2060 Owner’s Manual 41 References Foreword Target speakers Library name Subwoofer usage* For a floor monitor IF211595_pa – – IF211595_pa_sub ✓ – IF211599_pa – – IF211599_pa_sub ✓ – IF2115M64_pa – – IF2115M64_pa_sub ✓ – IF2115M95_pa – – IF2115M95_pa_sub ✓ – IF2115M99_pa – – IF2115M99_pa_sub ✓ – IF2115/95 IF2115/99 Introduction to the SP2060 IF2115M/64 IF2115M/95 IF2115M/99 * This setting is for full-range speakers. Subwoofer settings are not included. The Controls and Connectors Libraries for 2-way speaker processors N OT E These libraries also apply to 3-way speakers (including a combination of IL series and IH series speakers) that are used in biamp mode. Panel Operation The following table shows the settings for Yamaha Installation Series speakers (full-range, bi-amp mode). Target speakers IF2112/AS Library name – – IF2112AS_bi_sub ✓ – IF2112AS_bi_moni – ✓ IF211264_bi – – IF211264_bi_sub ✓ – IF211295_bi – – IF211295_bi_sub ✓ – IF211299_bi – – IF211299_bi_sub ✓ – IF2112M64_bi – – IF2112M64_bi_sub ✓ – IF2112M95_bi – – IF2112M95_bi_sub ✓ – IF2112M99_bi – – IF2112M99_bi_sub ✓ – IF2115AS_bi – – IF2115AS_bi_sub ✓ – IF2115AS_bi_moni – ✓ IF211564_bi – – IF211564_bi_sub ✓ – Network Settings IF2112/95 IF2112/99 IF2112M/64 IF2112M/95 References IF2112M/99 IF2115/64 42 SP2060 Owner’s Manual For a floor monitor IF2112AS_bi IF2112/64 IF2115/AS Subwoofer usage* Subwoofer usage* For a floor monitor IF211595_bi – – IF211595_bi_sub ✓ – IF211599_bi – – IF211599_bi_sub ✓ – IF2115M64_bi – – IF2115M64_bi_sub ✓ – IF2115M95_bi – – IF2115M95_bi_sub ✓ – IF2115M99_bi – – IF2115M99_bi_sub ✓ – IF311564_bi – – IF311564_bi_sub ✓ – IF311595_bi – – IF311595_bi_sub ✓ – IH2000/64 IH200064_bi – – IH2000/95 IH200095_bi – – IF2115/95 IF2115/99 IF2115M/64 IF2115M/95 IF2115M/99 IF3115/64 IF3115/95 Introduction to the SP2060 Library name The Controls and Connectors Target speakers Foreword References * This setting is for full-range speakers. Subwoofer settings are not included. Target speakers Library name Meaning IL1115 and IH2000/64 IL1115+IH64_pa Combination of IL1115 and IH2000/64 (passive mode) IL1116 and IH2000/95 IL1115+IH95_pa Combination of IL1115 and IH2000/95 (passive mode) Panel Operation The following table shows the settings for Yamaha Installation Series speaker IL series along with IH series. Target speakers Library name Subwoofer usage IF311564_tri – IF311564_tri_sub ✓ IF311595_tri – IF311595_tri_sub ✓ IF3115/64 IF3115/95 The following table shows the settings for Yamaha Installation Series speaker IL series along with IH series. Target speakers Library name Meaning IL1115 and IH2000/64 IL1115+IH64_bi Combination of IL1115 and IH2000/64 (bi-amp mode) IL1115 and IH2000/95 IL1115+IH95_bi Combination of IL1115 and IH2000/95 (bi-amp mode) SP2060 Owner’s Manual References The following table shows the settings for Yamaha Installation Series speakers (full-range, tri-amp mode). Network Settings Libraries for 3-way speaker processors 43 References Foreword Display Messages Warning and error messages Introduction to the SP2060 The Controls and Connectors Panel Operation Network Settings Message Meaning Action Duplicate IP Adr. Duplicate IP addresses. Change the IP addresses so that there are no duplicates. Illegal MAC Adr. An illegal MAC address has been encountered. This could be due to a hardware malfunction. Refer this problem to a contact a Yamaha dealer. Invalid IP Adr. The IP address is not set properly. Set an appropriate network IP address. Network Error A cable is disconnected, the power to the connected switching hub or router is turned off, or a cable is not in proper condition. Connect the cables properly, and make sure that the hub and/or router are operating correctly. No MAC Adr. MAC address not specified. This could be due to a hardware malfunction. Refer this problem to a Yamaha dealer. No Battery The internal battery is completely discharged or not installed. If you turn off the power to the unit, the current settings will be lost and reset to the default values. Stop operating the unit, and contact a Yamaha dealer for battery replacement. Critical Battery The internal battery is almost discharged. Your data may be lost. If you turn off the power to the unit, the current settings may be lost and reset to the default values. Stop operating the unit, and contact a Yamaha dealer for battery replacement. Low Battery The backup battery voltage is low. This does not affect the operation of the unit. However, if you continue using the unit, the settings may be lost and reset to the default values. Contact a Yamaha dealer for battery replacement at your earliest convenience. Recovering A program update attempt has failed, and the previous program is currently being restored. Do NOT turn power off while the unit is displaying this message. If the update attempt repeatedly fails, there may be a hardware malfunction. Refer this problem to a Yamaha dealer. Scene Recall Err A scene recall attempt has failed. Recall the scene again. If the problem persists, contact a Yamaha dealer. Saving Failed A save operation has failed. This could be due to a hardware malfunction. Refer this problem to a Yamaha dealer. Param Access Err Current setting cannot be displayed. Param Set Err Current setting cannot be changed. Save the current setting by using DME Designer, then initialize the unit. If the problem persists, contact a Yamaha dealer. W.Clk Unlocked A usable word clock signal is not being received or cannot be detected. Recheck all word clock connections and internal parameters. DevGrp Sync Err The device group configuration set via DME Designer does not match the real configuration. Use DME Designer to go off-line, create a configuration that correctly matches the actual configuration, and then go back on-line to synchronize the configuration. System Error A system error has occurred. Save the current setting by using DME Designer, then initialize the unit. If the problem persists, contact a Yamaha dealer. * Do NOT turn off the power to the SP2060 while the unit displays the message “DO NOT TURN OFF!” at the bottom of the display. References 44 SP2060 Owner’s Manual Status messages Meaning Connecting Connecting to the network. Download Success The program has been successfully updated. Downloading Program update in progress. Do NOT turn power off while the unit displays this message. File Operating A file operation is in progress during which the computer manipulates scene data. Do NOT turn power off while the unit displays this message. Network Setup Preparing network connection. Panel Locked The User Lock function is engaged. The panel controls do not work. Panel Unlocked The User Lock function has been disengaged. Panel operation is now possible. Scene Recalling Scene recall in progress. Scene Storing Scene store in progress. Do NOT turn power off while the unit displays this message. Cannot Recall Recalling scenes or libraries is disabled. Cannot Store The scene store is disabled. NO X-OVER Input channels do not feature the X-Over parameter. NO LIMITER Input channels do not feature the Limiter parameter. Protected You cannot edit or delete protected scenes. Panel Protected If the User Lock function is turned on, you cannot change the parameters by using the panel controls. NO ROUTING Input channel SUM does not feature the Routing parameter. NO LEVEL Input channel SUM does not feature the Level parameter. Network Busy There is too much network traffic. Communication is very slow. Synchronizing Data is being received from the computer. Do NOT turn power off while the unit displays this message. Scene Deleting Deleting a scene. Do NOT turn power off while the unit displays this message. * Do NOT turn off the power to the SP2060 while the unit displays the message “DO NOT TURN OFF!” at the bottom of the display. Panel Operation The Controls and Connectors Message Introduction to the SP2060 Foreword References Symptom No communication between the SP2060 and the DME Designer application software. Possible Causes Possible Solutions The connection cable is not connected properly. Make sure that the cable is properly connected. The computer's Ethernet port is not functioning properly. Refer to the DME Designer Installation Guide. The DME-N Network driver has not been installed. Install and set up the DME-N Network driver. The Mute function is turned on. Turn off the Mute function (see page 36). The output level is set too low. Increase the output level (see page 23). The User Lock function is turned on. Turn off the User Lock function (see page 33). Network Settings Troubleshooting The parameters cannot be edited. SP2060 Owner’s Manual References No audio output. 45 References Foreword General Specifications External Normal Rate: 44.1, 48 kHz (±0.1%) Double Rate: 88.2, 96 kHz (±0.1%) Internal 96 kHz Sampling Frequency Introduction to the SP2060 Signal Delay Less than 761 µ sec (INPUT to OUTPUT @Fs=96kHz) Indicators Key indicators x 9 MUTE indicators (INPUT A/B, OUTPUT 1–6) 6-segment LED level meters (INPUT A/B, OUTPUT 1–6) Miscellaneous Power Consumption 30 W Dimensions (HxDxW) 44 x 361 x 480 mm Net Weight 4.2 kg Temperature Range Operating: 5 to 40 ˚C Storage: –20 to 60 ˚C Included Accessories AC power cord, Rubber feet x 4, Owner’s manual The Controls and Connectors Electrical Characteristics Output impedance of signal generator: 150 Ω Frequency Response Input Panel Operation INPUT A, B Output OUTPUT 1–6 Conditions MIN TYP MAX Units 600 Ω Fs=96kHz@20Hz–40kHz, reference to the nominal output level @1kHz –1.0 0.0 +0.5 dB Conditions MIN TYP MAX Units Fs=96kHz, +4dBu@20Hz–40kHz 0.05 % Fs=96kHz, +22dBu@1kHz 0.007 % Fs=48kHz@1kHz, Input level: –1dBFS 0.015 % TYP MAX Units –79 dBu Total Harmonic Distortion Input Output RL INPUT A, B OUTPUT 1–6 600 Ω DIGITAL INPUT AES/EBU Network Settings RL OUTPUT 1–6 600 Ω * Total Harmonic Distortion is measured with a 18dB/octave filter @80kHz. Hum & Noise Input Output RL Conditions MIN INPUT A, B OUTPUT 1–6 600 Ω Fs=96kHz, Rs=150 Ω –82 DIGITAL INPUT AES/EBU OUTPUT 1–6 600 Ω Fs=48kHz, Input level: –∞dBFS –86 dBu *Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation. References Dynamic Range Input Output RL Conditions MIN TYP MAX INPUT A, B OUTPUT 1–6 600 Ω Fs=96kHz 106 dB DIGITAL INPUT AES/EBU OUTPUT 1–6 600 Ω Fs=48kHz 110 dB *Dynamic range is measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation. 46 SP2060 Owner’s Manual Units Crosstalk@1KHz Foreword References Fs=96kHz Input Output Conditions INPUT A OUTPUT 2, 4, 6 INPUT B OUTPUT 1, 3, 5 MIN TYP MAX Units INPUT A assigned to OUTPUT 1, 3 or 5 INPUT B assigned to OUTPUT 2, 4 or 6 –80 dB INPUT A assigned to OUTPUT 1, 3 or 5 INPUT B assigned to OUTPUT 2, 4 or 6 –80 dB Introduction to the SP2060 *Crosstalk is measured with a 18dB/octave filter @80kHz. LED Level Meters Metering points Conditions MIN TYP MAX Units OVER red LED: On 0 dBFS –6 amber LED: On –6 dBFS –12 amber LED: On –12 dBFS –18 amber LED: On –18 dBFS –30 green LED: On –30 dBFS –48 green LED: On –48 dBFS OVER red LED: On 0 dBFS LIMIT amber LED: On LIMIT* –6 green LED: On –6 dBFS –12 green LED: On –12 dBFS –18 green LED: On –18 dBFS –40 green LED: On –40 dBFS The Controls and Connectors INPUT A, B Panel Operation OUTPUT 1–6 *The LED turns on when the internal limiter is activated. Input/Output Characteristics Analog Input Characteristics INPUT A, B Actual Load Impedance For Use With Nominal 10 k Ω 600 Ω Lines Input level Nominal Connector Max. before clip +4 dBu (1.23 V) +24 dBu (12.28 V) XLR-3-31 type (balanced) *1 *1. XLR-3-31 type connectors with latches are balanced. (1=GND, 2=HOT, 3=COLD) *2. In these specifications, 0 dBu is referenced to 0.775 Vrms. *3. All AD converters are 24-bit linear, 64-times oversampling. (Fs=96kHz) Network Settings Input Terminals Analog Output Characteristics Actual Load Impedance For Use With Nominal OUTPUT 1–6 75 Ω 600 Ω Lines Input level Nominal Max. before clip +4 dBu (1.23 V) +24 dBu (12.28 V) Connector XLR-3-32 type (balanced) *1 *1. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD) *2. In these specifications, 0 dBu is referenced to 0.775 Vrms. *3. All DA converters are 24-bit linear, 128-times oversampling (Fs=48kHz) or 64-times oversampling (Fs=96kHz). References Output Terminals Digital Input Characteristics Terminal Format Data length Level Connector DIGITAL INPUT AES/EBU AES/EBU 24 bit RS422 XLR-3-31 type (balanced) *1 *2 *1. XLR-3-31 type connector with latch is balanced. (1=GND, 2=HOT, 3=COLD) *2. Only Double Speed Format is supported at 96 kHz. Double Channel or Single Format is not supported. SP2060 Owner’s Manual 47 References Foreword Control I/O Characteristics Terminal Format Level Connector Network IEEE 802.3 10Base-T/100Base-TX RJ-45 Introduction to the SP2060 Connector Pin Assignment [NETWORK] Connector (100Base-TX Ethernet, RJ-45) The Controls and Connectors Pin Connection 1 TxD+ 2 TxD- 3 RxD+ 4 Unused 5 Unused 6 RxD- 7 Unused 8 Unused Panel Operation Network Settings References 48 SP2060 Owner’s Manual Foreword References 480 Introduction to the SP2060 The Controls and Connectors 354 1 44 Rubber feet are included in the package. Panel Operation 440 3 361 (4) Dimensions * Specifications and descriptions in this owner's manual are for information purpose only. Yamaha Corp. reserves the right to charge or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. References European models Purchaser/User Information specified in EN55103-1 and EN55103-2. Inrush Current: 35A Conforms to Environments: E1,E2,E3 and E4. Network Settings Unit: mm SP2060 Owner’s Manual 49 References Foreword Index [▲INC/YES]/[▼DEC/NO] Keys ........................................... 21 Device Group page ..................................................................37 100Base-TX ............................................................................ 38 [DIGITAL INPUT] Connector (AES/EBU) ...........................22 Introduction to the SP2060 10Base-T ................................................................................. 38 Dimensions ..............................................................................49 2 x (2-way + Sub) .................................................................... 10 Display ....................................................................................21 2 x (2-way + Sub) Link ............................................................ 10 Displaying the current library ..................................................28 2 x 2-way + 2 x Aux ................................................................. 11 Displaying the firmware version ...............................................35 2 x 2-way + 2 x Aux Link ........................................................ 11 Displaying the label ..................................................................34 2 x 3-way ................................................................................. 12 Displaying word clock ..............................................................34 2 x 3-way Link ........................................................................ 12 DME Designer ..........................................................................7 3 x 2-way ................................................................................... 9 The Controls and Connectors 3 x 2-way Link .......................................................................... 9 E 4 way +2 x Aux ........................................................................ 13 Electrical Characteristics ..........................................................46 5-way + Aux ............................................................................ 14 EQ (Equalizer) .........................................................................24 6-way ...................................................................................... 15 [EQ] Key .................................................................................21 A F About a scene .......................................................................... 29 [FACTORY SETUP] ..............................................................35 [AC IN] Connector ................................................................. 22 Features .....................................................................................8 AdjustGc (Adjustable Gc) ....................................................... 28 Firmware Version ......................................................................7 Front Panel ..............................................................................21 B [BACK/STORE] Key .............................................................. 21 G Panel Operation Battery page ............................................................................ 35 General Specifications ..............................................................46 Bessel ...................................................................................... 28 Ground Screw ..........................................................................22 Butrwrth (Butterworth) ........................................................... 28 H C H.SHELF(High Shelving) .......................................................24 Changing a scene title ............................................................. 31 HPF .........................................................................................24 Changing the parameter values ................................................ 23 Checking the backup battery ................................................... 35 I Network Settings References Components ............................................................................. 8 Initializing the SP2060 ............................................................35 Configuration .......................................................................8, 9 2 x (2-way + Sub) ............................................................ 10 2 x (2-way + Sub) Link .................................................... 10 2 x 2-way + 2 x Aux ......................................................... 11 2 x 2-way + 2 x Aux Link ................................................ 11 2 x 3-way ......................................................................... 12 2 x 3-way Link ................................................................ 12 3 x 2-way ........................................................................... 9 3 x 2-way Link .................................................................. 9 4 way +2 x Aux ................................................................ 13 5-way + Aux .................................................................... 14 6-way .............................................................................. 15 Multi Zone ..................................................................... 16 INPUT A/B LINK ..................................................................32 Connector Pin Assignment ...................................................... 48 [CURRENT BACKUP] ......................................................... 35 INPUT A/B LINK page ..........................................................32 Input channel A .......................................................................26 Input channel B .......................................................................26 Input channel SUM .................................................................26 [INPUT] Connectors ...............................................................22 Input EQ .................................................................................24 Input routing ...........................................................................26 Input/Output Characteristics ...................................................47 IP address .................................................................................37 IP Address page ........................................................................37 L L.SHELF(Low Shelving) ..........................................................24 50 D Label page ................................................................................34 DELAY ................................................................................... 24 Last Memory Resume page ......................................................33 [DELAY] Key .......................................................................... 21 LEVEL ....................................................................................23 Deleting a scene ...................................................................... 32 [LEVEL] Key ...........................................................................21 SP2060 Owner’s Manual scene property ..........................................................................30 LIMITER ............................................................................... 29 [SEL] Keys ...............................................................................21 Limiter .................................................................................... 40 Setting a Device Group ............................................................37 [LIMITER] Key ...................................................................... 21 Setting Link Mode ...................................................................38 Link Mode page ...................................................................... 38 Setting the Crossover ...............................................................27 Linkwitz (Linkwitz-Riley) ....................................................... 28 Setting the IP Address ..............................................................37 LPF ......................................................................................... 24 Setting the Last Memory Resume ............................................33 Setting the Master ID ..............................................................38 M Slave ........................................................................................37 MAC Address page ................................................................. 39 Speaker ....................................................................................17 Master ..................................................................................... 37 Speaker processing ...................................................................17 Master ID page ....................................................................... 38 Status messages ........................................................................45 Meters ..................................................................................... 21 Storing a scene .........................................................................31 Multi Zone ............................................................................. 16 Subwoofer ................................................................................40 Multiple SP2060 ..................................................................... 19 System Examples .....................................................................17 Mute ....................................................................................... 36 [MUTE] Key .......................................................................... 21 T N Troubleshooting ......................................................................45 [NETWORK] Connector ....................................................... 22 Turning the power on and off ....................................................7 Thru ........................................................................................28 Introduction to the SP2060 scene number ...........................................................................30 The Controls and Connectors LIBRARY ............................................................................... 28 Library ...................................................................................... 8 Foreword References Network Settings .................................................................... 37 [NEXT/RECALL] Key ........................................................... 21 U User Lock page ........................................................................33 [OUTPUT] Connectors ......................................................... 22 user scene (readable and writable scene) .....................................9 Output EQ ............................................................................. 25 UTILITY .................................................................................32 Output routing ....................................................................... 26 [UTILITY] Key .......................................................................21 P V Parameters ................................................................................ 8 Version page ............................................................................35 PEQ ........................................................................................ 24 Viewing the MAC Address ......................................................39 [POWER ON/OFF] Key ........................................................ 21 Preset area ............................................................................... 30 W Preset Libraries ........................................................................ 40 W. Clock page .........................................................................34 preset parameters ....................................................................... 8 Warning and error messages ....................................................44 preset scene (read-only scene) .................................................... 9 [WITHOUT LIB.] ..................................................................35 Network Settings User Lock ................................................................................33 octet ........................................................................................ 37 Panel Operation User area ..................................................................................30 O Protecting a scene .................................................................... 31 X-OVER (Crossover) ...............................................................27 Rear Panel ............................................................................... 22 [X-OVER] Key ........................................................................21 Recalling a library ................................................................... 28 Recalling a scene ..................................................................... 30 Z ROUTING ............................................................................. 26 Zone processing .......................................................................18 References X R [ROUTING] Key ................................................................... 21 S SCENE ................................................................................... 29 Scene ......................................................................................... 8 [SCENE] Key ......................................................................... 21 SP2060 Owner’s Manual 51 Foreword Introduction to the SP2060 The Controls and Connectors Panel Operation Network Settings References SP2060 Owner’s Manual 52 MEMO References Network Settings Panel Operation The Controls and Connectors Introduction to the SP2060 Foreword MEMO SP2060 Owner’s Manual 53 Foreword Introduction to the SP2060 The Controls and Connectors Panel Operation Network Settings References SP2060 Owner’s Manual 54 MEMO For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México S.A. de C.V. Calz. Javier Rojo Gómez #1149, Col. Guadalupe del Moral C.P. 09300, México, D.F., México Tel: 55-5804-0600 BRAZIL Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. ASIA POLAND Yamaha Music Central Europe GmbH Sp.z. o.o. Oddzial w Polsce ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 THE NETHERLANDS/ BELGIUM/LUXEMBOURG Yamaha Music Central Europe GmbH, Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 FRANCE Yamaha Musique France BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 ITALY Yamaha Musica Italia S.P.A. Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 SPAIN/PORTUGAL Yamaha Musical do Brasil Ltda. Av. Reboucas 2636-Pinheiros CEP: 05402-400 Sao Paulo-SP. Brasil Tel: 011-3085-1377 ARGENTINA Yamaha-Hazen Música, S.A. Ctra. de la Coruna km. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 SWEDEN Yamaha Music Latin America, S.A. Sucursal de Argentina Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-4371-7021 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM Yamaha-Kemble Music (U.K.) Ltd. Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England Tel: 01908-366700 GERMANY Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 SWITZERLAND/LIECHTENSTEIN Yamaha Music Central Europe GmbH, Branch Switzerland Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: 01-383 3990 AUSTRIA Yamaha Music Central Europe GmbH, Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 CZECH REPUBLIC/SLOVAKIA/ HUNGARY/SLOVENIA Yamaha Music Central Europe GmbH, Branch Austria, CEE Department Schleiergasse 20, A-1100 Wien, Austria Tel: 01-602039025 Yamaha Scandinavia AB J. A. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. 25/F., United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 INDONESIA PT. Yamaha Music Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 KOREA Yamaha Music Korea Ltd. Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong, Youngdungpo-ku, Seoul, Korea Tel: 02-3770-0660 MALAYSIA Yamaha Music Malaysia, Sdn., Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 SINGAPORE Yamaha Music Asia Pte., Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 TAIWAN Yamaha KHS Music Co., Ltd. 3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C. Tel: 02-2511-8688 DENMARK YS Copenhagen Liaison Office Generatorvej 6A DK-2730 Herlev, Denmark Tel: 44 92 49 00 NORWAY Norsk filial av Yamaha Scandinavia AB Grini Næringspark 1 N-1345 Østerås, Norway Tel: 67 16 77 70 OTHER EUROPEAN COUNTRIES Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 AFRICA Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2313 MIDDLE EAST TURKEY/CYPRUS Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 THAILAND Siam Music Yamaha Co., Ltd. 891/1 Siam Motors Building, 15-16 floor Rama 1 road, Wangmai, Pathumwan Bangkok 10330, Thailand Tel: 02-215-2626 OTHER ASIAN COUNTRIES Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2317 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2313 OTHER COUNTRIES Yamaha Music Gulf FZE LB21-128 Jebel Ali Freezone P.O.Box 17328, Dubai, U.A.E. Tel: +971-4-881-5868 HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2441 PA13 Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ This document is printed on chlorine free (ECF) paper with soy ink. U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2006 Yamaha Corporation WG50780 605IPDHx.x-02B0 Printed in Japan-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
Yamaha SP2060 de handleiding
- Categorie
- Audio-equalizers
- Type
- de handleiding
in andere talen
- English: Yamaha SP2060 Owner's manual
- italiano: Yamaha SP2060 Manuale del proprietario
- русский: Yamaha SP2060 Инструкция по применению
- français: Yamaha SP2060 Le manuel du propriétaire
- español: Yamaha SP2060 El manual del propietario
- Deutsch: Yamaha SP2060 Bedienungsanleitung
- português: Yamaha SP2060 Manual do proprietário
- dansk: Yamaha SP2060 Brugervejledning
- suomi: Yamaha SP2060 Omistajan opas
- čeština: Yamaha SP2060 Návod k obsluze
- svenska: Yamaha SP2060 Bruksanvisning
- Türkçe: Yamaha SP2060 El kitabı
- polski: Yamaha SP2060 Instrukcja obsługi
- română: Yamaha SP2060 Manualul proprietarului