Yamaha XMV4140 de handleiding

Merk: Yamaha

Model: XMV4140

Categorie: Aanvullende muziekapparatuur

Type: de handleiding

Deze handleiding is ook geschikt voor

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Manuale di istruzioni

Руководство пользователя

EnglishDeutschFrançaisEspañolItalianoРусский

POWER AMPLIFIER

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

The above warning is located on the top of the unit.

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to per-

sons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and mainte-

nance (servicing) instructions in the literature

accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radia-

tors, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The

wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your out-

let, consult an electrician for replacement of the

obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-

cles, and the point where they exit from the appara-

tus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table speci-

fied by the manufacturer, or

sold with the apparatus. When

a cart is used, use caution

when moving the cart/appara-

tus combination to avoid injury

from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Ser-

vicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det

brugte batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä

käytetty paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifi-

cations not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could

void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these require-

ments provides a reasonable level of assurance that your

use of this product in a residential environment will not result

in harmful interference with other electronic devices. This

equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the opera-

tion of other electronic devices. Compliance with FCC regu-

lations does not guarantee that interference will not occur in

all installations. If this product is found to be the source of

interference, which can be determined by turning the unit

“

OFF

” and “ON”, please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distrib-

ute this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America,

Electronic Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park,

Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Power Amplifier

Model Name : XMV4280/XMV4140/XMV4280-D/

XMV4140-D

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including

interference that may cause undesired operation.

See user manual instructions if interference to radio reception

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(FCC DoC)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED IMPOR-

TANT. The wires in this mains lead are coloured in accordance

with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be

connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol or colored GREEN or

GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

(3 wires)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

This product contains a battery that contains perchlorate material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate)

이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으

로 하며, 모든 지역에서 사용할 수 있습니다.

(class b korea)

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited

to, the following:

• Do not place the power cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy

objects on it, or place it in a position where anyone could walk on, trip over,

or roll anything over it.

• Only use the voltage specified as correct for the device. The required voltage

is printed on the name plate of the device.

• Use only the supplied power cord/plug.

If you intend to use the device in an area other than in the one you

purchased, the included power cord may not be compatible. Please check

with your Yamaha dealer.

• Check the electric plug periodically and remove any dirt or dust which may

have accumulated on it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock, damage to

the device(s), or even fire.

• This device contains no user-serviceable parts. Do not open the device or

attempt to disassemble the internal parts or modify them in any way. If it

should appear to be malfunctioning, discontinue use immediately and have

it inspected by qualified Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions, or place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings. If any liquid such as

water seeps into the device, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the device inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may

fall over and cause a fire.

• When one of the following problems occur, immediately turn off the power

switch and disconnect the electric plug from the outlet. Then have the device

inspected by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the device.

• If this device should be dropped or damaged, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualified Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the device or other property. These precautions include, but are not limited to, the following:

• When removing the electric plug from the device or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the device is not to be used

for extended periods of time, or during electrical storms.

• Do not place the device in an unstable position where it might accidentally

fall over.

• Do not block the vents. This device has ventilation holes at the front/rear/

sides to prevent the internal temperature from becoming too high. In

particular, do not place the device on its side or upside down. Inadequate

ventilation can result in overheating, possibly causing damage to the

device(s), or even fire.

• Do not use the device in a confined, poorly-ventilated location. If this device

is to be used in a small space other than an EIA-standard rack, make sure

that there is adequate space between the device and surrounding walls or

other devices: at least 10 cm at the sides, 10 cm behind and 40 cm above.

Inadequate ventilation can result in overheating, possibly causing damage to

the device(s), or even fire.

• Do not place the device in a location where it may come into contact with

corrosive gases or salt air. Doing so may result in malfunction.

• Keep device away from the reach of children.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn

off the power switch and disconnect the plug from the outlet. Even when the

power switch is turned off, electricity is still flowing to the product at the

minimum level. When you are not using the product for a long time, make

sure to unplug the power cord from the wall AC outlet.

• If the device is mounted in an EIA standard rack, carefully read the section

“Precautions for Rack Mounting” on page 8. Inadequate ventilation can

result in overheating, possibly causing damage to the device(s),

malfunction, or even fire.

• Before connecting the device to other devices, turn off the power for all

devices. Before turning the power on or off for all devices, set all volume

levels to minimum.

• Use only speaker cables for connecting speakers to the speaker connectors.

Use of other types of cables may result in fire.

Power supply/power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/power cord

Location

Connections

PA_en_1 1/2

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

• Remove the power plug from the AC outlet when cleaning the device.

• Do not insert your fingers or hands in any gaps or openings on the device

(vents).

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into

any gaps or openings on the device (vents) If this happens, turn off the

power immediately and unplug the power cord from the AC outlet. Then

have the device inspected by qualified Yamaha service personnel.

• Do not rest your weight on the device or place heavy objects on it, and avoid

use excessive force on the buttons, switches or connectors.

• Do not use speakers for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

• This device has a built-in backup battery. When you unplug the power cord

from the AC outlet, the internal data is retained. However, if the backup

battery fully discharges, this data will be lost. When the backup battery is

running low, the display indicates “012.” and the ALERT indicator is

flashing. In this case, immediately save the data to external device such as a

computer, then have qualified Yamaha service personnel replace the backup

battery.

Always turn the power off when the device is not in use.

NOTICE

To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.

 Handling and maintenance

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the device,

TV, or radio may generate noise.

• Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car

during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wip-

ing cloths.

• Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from one

location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause dam-

age. If there is reason to believe that condensation might have o

ccurr

ed, leave the device for several hours without turning on the

power until the condensation has completely dried out.

• Do not use this device for any purpose other than driving loudspeakers.

• When turning on the AC power in your audio system, always turn on tthe device LAST, to avoid speaker damage. When turning the

power off, the device should be turned off FIRST for the same reason.

 Saving data

This device has a built-in backup battery that maintains data in internal memory even when the device’s power is switched off. The

backup battery will eventually become depleted, however, and when that happens the contents of the internal memory will be lost.*

To prevent loss of data be sure to replace the backup battery before it becomes fully depleted. When the remaining capacity of the

backup battery becomes so low that it needs to be replaced a “012.” message will appear on the display during operation or when the

device is powered on. If either of these messages appears do not turn off the power and immediately transfer any data you want to save

to a computer or other external storage device, then have qualif

ied Yamaha service

personnel replace the backup battery. The average

life of the internal backup battery is approximately 5 years, depending on operating conditions.

* Data items maintained in the internal memory by the backup battery are as follows:

•Device parameters (Attenuator values, Polarity settings, HPF settings, Analog/digital input setting, and [SIGNAL] indicator display

setting).

•Event log.

Data items other than those described above are stored in memory that does not require backup power, and will be retained even if the

backup battery fails.

Information

 About this manual

• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your

device.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Maintenance

Handling caution

Backup battery

Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.

European Models

Inrush Current based on EN 55103-1:2009

10A (on initial switch-on)

5A (after a supply interruption of 5s)

Conforms to Environments: E1, E2, E3 and E4

PA_en_1 2/2

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Contents

Introduction.....................................................................................................................7

Features.................................................................................................................................. 7

Included items......................................................................................................................... 7

Related Manuals and Software............................................................................................... 7

Firmware Updates................................................................................................................... 8

About Dante ............................................................................................................................ 8

Precautions for Rack Mounting ............................................................................................... 8

Controls and Functions .................................................................................................9

Front Panel.............................................................................................................................. 9

Rear Panel ............................................................................................................................ 12

Connections and Setting Up .......................................................................................16

Setup for Analog Signal Input ............................................................................................... 16

[REMOTE] and [FAULT OUTPUT] Connectors ..................................................................... 21

Operations.....................................................................................................................23

Front Panel Operations ......................................................................................................... 23

Initializing the Internal Memory............................................................................................. 25

Appendix .......................................................................................................................26

Troubleshooting..................................................................................................................... 26

Alert Numbers and Content .................................................................................................. 27

Dante Messages (XMV4280-D/XMV4140-D only)................................................................ 29

High-impedance and Low-impedance Connections ............................................................. 30

BTL (Balanced Transformer Less) Connection..................................................................... 31

Specifications .............................................................................................................234

General Specifications........................................................................................................ 234

Block Diagram..................................................................................................................... 236

Dimensions ......................................................................................................................... 236

Current Draw and Heat Dissipation .................................................................................... 237

* The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous

improvements to the product, this manual may not apply to the specifications of your particular product. To obtain the lat-

est manual, access the Yamaha website then download the manual file. Since specifications, equipment or separately

sold accessories may not be the same in every locale, please check with your Yamaha dealer.

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Introduction

Thank you for your purchase of the Yamaha XMV4280, XMV4140, XMV4280-D or XMV4140-D power

amplifier. Please read through this manual carefully before beginning use, so that you will be able to take full

advantage of your power amplifier’s superlative features and enjoy trouble-free operation for years to come.

After you have read the manual, keep it in a safe place for reference when needed.

The XMV is a multi-channel power amplifier with the follow-

ing features.

• Both high-impedance and low-impedance connec-

tions are supported

Both high-impedance connections to 70V/100V lines and

4Ω/8Ω low-impedance connections are supported. A rear

panel DIP switch allows this setting to be specified for every

two channels.

• Newly-developed “Double Power mode”

The newly-developed “Double Power mode” doubles the

amplifier output of each channel when low-impedance con-

nections are used.

* The number of available channels will be halved.

•Settings can be made via application software

Although settings such as mute on/off and attenuator values

can be edited from the panel of the amplifier itself, you can

use an MTX series matrix processor and computer to edit the

settings of multiple XMV units.

• Support for the newly-developed “YDIF” digital

audio transmission format

(XMV4280/XMV4140 only)

This allows up to 16 channels of audio and word clock to be

transmitted and received via an Ethernet cable.

This model can receive four channels of audio signals via

YDIF.

• Dante network for large-scale systems

(XMV4280-D/XMV4140-D only)

This enables audio signal transfer over long-distance with

Dante equipped devices (such as the MTX5-D) with stan-

dard Ethernet cables.

•High efficiency

The newly-developed output circuits allows high efficiency.

• Redundancy between the digital and analog inputs

When the pilot tone of a digital input is interrupted or an

analog input reaches the specified level or higher, the input

switches from digital to analog.

*This function can be set from the Amp Editor.

• Owner’s Manual

•Power cord

• Euroblock plugs (3-pin, 3.50mm pitch) x 2

• Euroblock plugs with tabs (3-pin, 5.08mm pitch) x 4

• Cable ties x 4

Use the MTX-MRX Editor for building a system in which the

MTX/MRX and XMV are combined. Use the Amp Editor for a

system consisting only of the XMV(s). Related manuals, of the

MTX-MRX Editor or Amp Editor (heretofore collectively

referred to as “the editor”) can be downloaded from the down-

load page of the following website.

http://www.yamahaproaudio.com/

• List of related manuals

The “MTX-MRX Editor User Guide,” “MTX Setup Manual,”

“MRX Setup Manual,” and “Amp Editor Owner’s Manual” are

electronic files in PDF format.

You can read the books on a computer. Use Adobe® Reader®

to read the books on screen, search for words very quickly, print

specific pages, or click links to display sections of special inter-

est. The ability to search for words, or to follow links directly to

relevant sections in the document, are helpful attributes of this

electronic file format. We encourage you to take advantage of

these benefits.

You can download the latest Adobe Reader application from the

website listed below.

http://www.adobe.com/

NOTE

• When there are differences in the specifications of the XMV4280/XMV4280-D and the XMV4140/XMV4140-D, this manual will

use curly brackets { } to enclose information that applies only to the XMV4140/XMV4140-D.

(Example: 280W {140W}).

• Unless otherwise specified, illustrations are taken from the XMV4280/XMV4280-D.

• For the remainder of this manual, the XMV4280, XMV4140, XMV4280-D and XMV4140-D are referred to as “XMV” collectively.

•In this book, the matrix processor MTX series units are reffered to as “MTX” collectively.

Features Included items (please check)

Related Manuals and Software

MTX or MRX

owner’s manual

This explains how to use the proces-

sor (MTX or MRX).

MTX-MRX Editor

User Guide

This explains how to use MTX-MRX

Editor.

MTX Setup Manual

MRX Setup Manual

This explains how to use and set up

the matrix processor MTX and MRX

series that is used along with the

XMV power amp.

Amp Editor

Owner’s Manual

This explains how to use Amp Editor.

Introduction

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Use the MTX-MRX Editor or the Amp Editor to update the

firmware of the XMV or check the firmware version. For opera-

tion details, refer to the related manuals.

You can download the latest firmware from the “Downloads”

page on the following website.

http://www.yamahaproaudio.com/

The XMV4280-D/XMV4140-D units feature Dante technology

as a protocol to transmit audio signals. Dante is a network pro-

tocol developed by Audinate. It is designed to deliver multi-

channel audio signals at various sampling and bit rates, as well

as device control signals over a Giga-bit Ethernet (GbE) net-

work. Dante also offers the following benefits:

• It transmits up to 512 in/512 out, for a total 1024 channels

(theoretically) of audio over a GbE network.

(The XMV4280-D/XMV4140-D features four inputs with a

24/32-bit resolution.)

• Dante-enabled devices will automatically configure their

network interfaces and find each other on the network. You

can label Dante devices and their audio channels with names

that make sense to you.

• Dante uses high accuracy network synchronization standards

to achieve sample-accurate playback with extremely low

latency and jitter.

(Four types of latency are available on the XMV4280-D/

XMV4140-D: 0.25 msec, 0.5 msec, 1.0 msec, and 5.0 msec.)

• Dante supports redundant connections via primary and sec-

ondary circuits to defend against unforeseen difficulties.

• Connecting a Dante-enabled device to a computer over

Ethernet enables you to directly input or output audio signals

without using any audio interface devices.

Visit Audinate website for more details on Dante.

http://www.audinate.com/

More information on Dante is also posted on the Yamaha Pro

Audio website:

http://www.yamahaproaudio.com/

Firmware Updates

About Dante

NOTE

Please do not use the EEE function (*) of network switches in a

Dante network.

Although power management should be negotiated automati-

cally in switches that support EEE, some switches do not per-

form the negotiation properly.

This may cause EEE to be enabled in Dante networks when it

is not appropriate, resulting in poor synchronization perfor-

mance and occasional dropouts.

Therefore we strongly recommend that:

- If you use managed switches, ensure that they allow EEE to

be disabled. Make sure that EEE is disabled on all ports

used for real-time Dante traffic.

- If you use unmanaged switches, make sure to not use net-

work switches that support the EEE function, since EEE

operation cannot be disabled in these switches.

* EEE (Energy Efficient Ethernet) is a technology that reduces switch

power consumption during periods of low network traffic. It is also

known as Green Ethernet and IEEE802.3az.

Precautions for Rack Mounting

This unit is rated for operation at ambient temperatures

ranging from 0 to 40 degrees Celsius. When mounting

the unit with other XMV unit(s) or other device(s) in an

EIA standard equipment rack, internal temperatures can

exceed the specified upper limit, resulting in impaired

performance or failure. When rack mounting the unit,

always observe the following requirements to avoid heat

buildup:

• When mounting the unit in a rack with devices such as

power amplifiers that generate a significant amount of

heat, leave more than 1U of space between the XMV

and other equipment. Also either leave the open

spaces uncovered or install appropriate ventilating pan-

els to minimize the possibility of heat buildup.

• To ensure sufficient airflow, le

ave the

rear of the rack

open and position it at least 10 centimeters from walls

or other surfaces. If the rear of the rack can’t be left

open, install a commercially available fan or similar

ventilating option to secure sufficient airflow. If you’ve

installed a fan kit, there may be cases in which closing

the rear of the rack will produce a greater cooling effect.

Refer to the rack and/or fan unit manual for details.

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Controls and Functions

XMV4280/XMV4140

XMV4280-D/XMV4140-D

q Power switch

Turns power to the unit ON or OFF. Setting the switch to the

upward position turns the power on; the [POWER] indicator

!0 will light green. Setting the switch to the downward posi-

tion turns the power off. If the switch is in the upward posi-

tion and the [POWER] indicator is flashing, the unit is in

standby mode.

w [PROTECTION] A/B/C/D indicators

When the protection system is active, the indicator will light

orange. If the audio output is muted, turn off the power and

wait for the XMV to cool before turning the power on again.

The protection circuit will operate and the [PROTECTION]

indicator will light in the following situations.



If the amplifier overheats and the output lim-

iter operates

The speaker output will be attenuated if the heat sink of

the amplifier section exceeds 80°C, and will be muted if

the heat sink exceeds 90°C. The [PROTECTION] indica-

tor will light at 80°C or higher.



If the power supply overheats and shuts-down

The fan will rotate at high speed if the power supply sec-

tion exceeds 90°C, and the analog circuits will shut down

if it exceeds 100°C.

The [PROTECTION] indicator will light at 100°C or

higher.

Front Panel

q wer!8 !8 !0

i t u !7o

!1 !2 !3

q wer!8 !8 !0

i t u !7o

!4!5

CAUTION

• To ensure that high-volume noise is not output from

the speakers, power-on the equipment starting with

the audio sources, then the mixer and processors

(such as the MTX), and finally the amplifiers. Reverse

this order when turning the system off.

• Rapidly turning the power switch ON and OFF in suc-

cession can cause the unit to malfunction. After turn-

ing the power switch OFF, wait for about 5 seconds

before turning it ON again.

• If you modified parameter settings, do not turn the

power switch OFF for at least one second. Otherwise,

the changes to the settings may be lost.

• Even when the power switch is turned off, a small

amount of current is flowing through the unit. If you

plan not to use the unit for a long period of time,

remove the power cable from the AC outlet.

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 When overcurrent is detected

If for any reason the impedance falls below the specifica-

tion for the mode, the speaker output is muted to prevent

overcurrent; muting will be cancelled after approximately

one second. If overcurrent is detected after muting is can-

celled, the output will be muted again.



If DC output is detected

The power supply section will be shut down.

 If excessive total current or maximum current

is detected

The output signal will be lowered.

e [LIMIT] A/B/C/D indicators

When the limiter operates, the speaker output will be limited

and the indicator will light red. Lower the attenuator value so

that the limiter does not activate, referring to “Changing the

attenuator setting” (page 20). The limiter will operate in the

following situations.

• When an instantaneous input overload is detected

• When an input overload has been occurring for a specific

duration

• When the heat sink of the amplifier section exceeds the

allowable temperature

r [SIGNAL] A/B/C/D indicators

The [SIGNAL] indicator will light in green when the input/

output signal level exceeds a certain level.

*1 For details on switching the indicator between input and

output, refer to “Front Panel Operations” (page 23).

*2 Depends on the condition. Refer to “[SIGNAL] Indicator Lit

Level” (page 235).

t [SELECT] A/B/C/D buttons/indicators

Use these buttons to select the output channel that you want

to control. The indicator of the selected channel will light in

green.

By using these in conjunction with the [FUNCTION] button

!7, you can change the parameter that is controlled by the

encoder. Refer to “Front Panel Operations” (page 23).

When the [PANEL LOCK] indicator !6 is lit, front panel

operations are locked, and output channel operations are not

possible. Defeat the lock if you want to perform these opera-

tions.

y Display

This is a 3-digit 7-segment display that shows information

such as the attenuator value of the channel selected by the

[SELECT] button t or the alert number (page 27).

u Encoder

This encoder is used to edit parameters. For details on the

available parameters, refer to “Front Panel Operations”

(page 23).

When the [PANEL LOCK] indicator !6 is lit in orange, front

panel operations are locked, and settings cannot be edited.

Defeat the lock if you want to perform these operations.

i [MUTE] A/B/C/D indicators

When you mute an output channel by operating the unit

itself or by operations via the [REMOTE] connector @7 or

the editor, the indicator of the corresponding channel will

light yellow.

o [MUTE] button

By holding down the [MUTE] button and pressing the

[SELECT] button t, you can switch muting on/off for the

channel selected by the [SELECT] button. When muting

turns on, the [MUTE] indicator i will light in yellow.

When the [PANEL LOCK] indicator !6 is lit, front panel

operations are locked, and channel mute operations are not

possible. Defeat the lock if you want to perform these opera-

tions.

!0 [POWER] indicator

This will light in green when the power supply is turned on

by the power switch q.

It will flash when the unit is switched to standby mode via

the [REMOTE] connector or the editor.

!1 [ALERT] indicator

This will flash or light when an abnormality occurs in the

unit.

If this is flashing, note the indication in the display and refer

to “Alert Numbers and Content” (page 27).

If it is lit, stop operating the unit. After a time, the indicator

will change to flashing, and an alert number will appear in

the display.

!2 [NETWORK] indicator (XMV4280/XMV4140 only)

This will light green if the XMV is in a linked state with an

external device via the network connector !9. It will flash

while data is being communicated.

!3 [YDIF] indicator (XMV4280/XMV4140 only)

This will light green when the [YDIF] connector @0 is con-

nected normally and a valid word clock is being input.

Connector

[SIGNAL]

indicators

used for

(*1)

Indicator

illumina-

tion status

Analog input connectors @4

input

-40dBFS or

[YDIF] connectors @0

(XMV4280/XMV4140)

Dante [PRIMARY] connector

Dante [SECONDARY] connec-

tor @1

(XMV4280-D/XMV4140-D)

[SPEAKERS] output connec-

tors @6

output

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

!4 [PRIMARY]/[SECONDARY] indicators

(XMV4280-D/XMV4140-D only)

These show the communication status of the Dante [PRI-

MARY]/[SECONDARY] connectors @1. They flash rapidly

in green if the Ethernet cables are connected properly.

!5 [SYNC] Indicators

(XMV4280-D/XMV4140-D only)

These show the operating status of the Dante network. If the

green (upper) indicator lights, the unit is operating as a word

clock slave and synchronizing to the word clock. If the green

indicator flashes, the unit is operating as the word clock mas-

ter. If the power to the unit is turned on but the green indica-

tor is turned off, the unit is not functioning properly. In this

case, refer to the “Warning Messages” section (see page 29).

If the orange indicator lights or flashes, refer to the “Warning

Messages” section.

!6 [PANEL LOCK] indicator

This lights or flashes according to the state of the front panel

lock. To specify the front panel lock setting, use the Device

setup DIP switch @3.

!7 [FUNCTION] button

Use this to check or change the operating mode of the

XMV’s front panel. For details on how to perform front

panel operations, refer to “Front Panel Operations” (page

23).

!8 Cooling vent

Located behind the vent is a variable speed cooling fan that

draws air in from the front and exhausts it through the rear.

The fan speed will automatically vary according to the tem-

perature.

Please be sure that you do not block the air intakes or

exhaust vents. You should also clean the air intakes and

exhaust vents regularly. If the air intakes are clogged with

dust or debris, the unit will overheat, which may result in the

unit shutting down.

Indicator Status

Lit

Front panel operations are locked. Lock

will be temporarily defeated if you press

the [FUNCTION] button !7 and the

[SELECT] A button t.

Unlit Front panel operations are not locked.

Flashing

Lock is temporarily defeated. When the

XMV is restarted, it will be in a locked

state.

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

XMV4280/XMV4140

XMV4280-D/XMV4140-D

!9 Network connector (XMV4280/XMV4140 only)

This is a 100BASE-TX Ethernet connector that allows the

unit to be connected to a computer via an Ethernet cable.

@0 [YDIF] connectors (XMV4280/XMV4140 only)

These are RJ-45 connectors that allow the unit to be con-

nected via an Ethernet cable to another YDIF-equipped

device so that audio signals and word clock signals can be

transmitted and received. Using a ring connection (YDIF

connection), you can connect to other devices equipped with

a [YDIF] connector. For details on settings for receiving

audio signals via the [YDIF] connector, refer to “Front Panel

Operations” (page 23).

Cables used for this connection should be 30 meters or less

between devices. Up to eight devices can be connected in a

network with YDIF connection.

For information on connections that use [YDIF] connectors,

refer to the “MTX Setup Manual.”

Rear Panel

1 2 3 4 5 6 7 8

@8@7@5!9 @9

@4 @6

@0 @2

1 2 3 4 5 6 7 8

@8@7@5 @9

@4 @6

NOTE

• Use a CAT5e or better STP (Shielded Twisted Pair) cable

for the network connection to prevent electromagnetic

interference.

• When using MTX-MRX Editor to control the XMV, you

must connect the MTX.

NOTE

To prevent electromagnetic interference, make connections

to the [YDIF] connector using a CAT5e or better STP

(Shielded Twisted Pair) cable in which all pins are con-

nected with a straight connection.

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

@1 Dante [PRIMARY]/[SECONDARY] connectors

(XMV4280-D/XMV4140-D only)

These are RJ-45 connectors that allow the unit to be con-

nected to another Dante device such as the MTX5-D via an

Ethernet cable. The Dante [PRIMARY] connector can also

be used to connect to a computer via an Ethernet cable. To

connect, refer to the “MTX-MRX Editor User Guide.”

@2 [UNIT ID] rotary switch

If multiple devices such as XMVs or MTXs are connected

on the same network, this rotary switch enables you to spec-

ify the UNIT ID that identifies each unit individually.

XMV4280/XMV4140

With the combination of the device setup DIP switches

1–3 @3 for upper digits and the rotary switch for lower dig-

its, the UNIT ID can be specified in a maximum of 127

values, from “01” to “7F.”

XMV4280-D/XMV4140-D

With the rotary switch (HIGH) used for upper digits and

the rotary switch (LOW) for lower digits, the UNIT ID can

be specified in a maximum of 254 values, from “01” to

“FE.”

@3 Device setup DIP switch

This DIP switch is used to make settings for the XMV. Refer

to the following for details on the settings.

Refer to the following for details.

XMV4280/XMV4140

XMV4280-D/XMV4140-D

NOTE

• Use a CAT5e or better STP (Shielded Twisted Pair) cable

for the connection to the Dante [PRIMARY]/[SECOND-

ARY] connectors to prevent electromagnetic interference.

Make sure that the metal parts of the plugs are electrically

connected to the STP cable shield by conductive tape or

comparable means.

• Connect only Dante-compatible devices or GbE-compati-

ble devices (including a computer).

• Since Dante-compatible equipment made by Yamaha

such as the XMV4280-D/XMV4140-D contains a built’-in

network switch, the number of hops will be two or more.

For this reason, the 0.15 msec Latency setting in Dante

Controller will be grayed-out and unavailable.

NOTE

• Do not use “00” or “FF” as the UNIT ID.

•After you set the [UNIT ID] rotary switch, turn the power to

the unit off and then on.

NOTE

To change the switch settings, turn off the power to the unit.

If you change the settings while the power is on, the change

will not be effective until you turn the unit off and then on.

Switch Status

Indicates the switch is in the upward posi-

tion.

Indicates the switch is in the downward posi-

tion.

NOTE

Switch 1 and 2 are not used for the XMV4280-D/XMV4140-

D. Use the swiches in the factory set state (upward).

12345678

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Switch 1–3 (UNIT ID)

(XMV4280/XMV4140 only)

Use the DIP switches 1–3 to specify the upper digit, and

use the [UNIT ID] rotary switch @2 to specify the lower

digit to set a maximum of 127 combinations of UNIT ID

in the range of 01 through 7F (127).



Switch 3 (SECONDARY PORT)

(XMV4280-D/XMV4140-D only)

This sets the Dante [SECONDARY] connector @1 on the

rear panel as to whether it will be used for daisy chain

connection or redundant. For details on the connection,

refer to the “MTX-MRX Editor User Guide.”



Switch 4 (LED DIMMER)

This specifies the brightness of the front panel indicators

and display.



Switch 5 (PANEL LOCK)

This specifies the front panel lock setting (locks all panel

operations including the [MUTE] button o and attenua-

tion adjustments). By selecting the LOCK setting after

you’ve completed all settings, you can prevent the vol-

ume or mute settings from being inadvertently changed.

Even if the LOCK setting is selected, you can temporarily

unlock the panel by pressing the [FUNCTION] button !7

and the [SELECT] A button t. The panel will be re-

locked when one minute has passed without any opera-

tion being performed, or when you once again press the

[FUNCTION] button and the [SELECT] A button, or

when you turn off the power.



Switch 6 (IP SETTING)

This selects whether the UNIT ID value will be used as

the IP address for the unit to communicate with a com-

puter, or whether the IP address will be assigned by the

editor or the DHCP server.

DIP Switches

Setting Description

The UNIT ID’s

upper digit is

set to 0.

The setting range of the

[UNIT ID] rotary switch is

from 01 through 0F.

The UNIT ID’s

upper digit is

set to 1.

The setting range of the

[UNIT ID] rotary switch is

from 10 through 1F.

The UNIT ID’s

upper digit is

set to 2.

The setting range of the

[UNIT ID] rotary switch is

from 20 through 2F.

The UNIT ID’s

upper digit is

set to 3.

The setting range of the

[UNIT ID] rotary switch is

from 30 through 3F.

The UNIT ID’s

upper digit is

set to 4.

The setting range of the

[UNIT ID] rotary switch is

from 40 through 4F.

The UNIT ID’s

upper digit is

set to 5.

The setting range of the

[UNIT ID] rotary switch is

from 50 through 5F.

The UNIT ID’s

upper digit is

set to 6.

The setting range of the

[UNIT ID] rotary switch is

from 60 through 6F.

The UNIT ID’s

upper digit is

set to 7.

The setting range of the

[UNIT ID] rotary switch is

from 70 through 7F.

DIP Switches Setting Description

DAISY CHAIN

The Dante [SECOND-

ARY] connector is used

for a daisy chain connec-

tion. A signal at the

Dante [PRIMARY] con-

nector will be transmitted

to the next device in the

chain as is.

REDUNDANT

The Dante [SECOND-

ARY] connector is used

for a redundant network.

It will function as backup

connection, independent

of the network to which

the Dante [PRIMARY]

connector is connected.

DIP Switches

Setting Description

OFF Normal brightness.

Reduced brightness. Use

this setting if the indicators

and the display are too

bright.

NOTE

The brightness of the [POWER] indicator !0 will not be

reduced.

DIP Switches

Setting Description

UNLOCK

The front panel will not be

locked.

LOCK

Front panel operations

other than the power will be

locked.

DIP Switches

Setting Description

UNIT ID

The IP address will be

specified using the UNIT ID

value.

The IP address will be

192.168.0.xxx (xxx is the

UNIT ID value).

However, if the UNIT ID is

“FF,” xxx is 127.

The IP address will be

specified by the editor or the

DHCP server.

NOTE

Set this to the “UNIT ID” position the first time you con-

nect this device to a computer after purchase. After

specifying the IP address from the editor, change this

switch to the “PC” position.

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Switches 7 and 8 (START UP MODE)

These specify the startup mode.

@4 Analog input connectors

These are Euroblock 3-pin analog audio input connectors.

For details on settings for receiving audio signals via the

analog input connectors, refer to “Front Panel Operations”

(page 23).

For details on how to attach Euroblock connectors, refer to

the “Connections and Setting Up” section entitled “Connect-

ing the Analog Inputs (Euroblock)” (page 16).

@5 [SPEAKERS] DIP switch

This DIP switch makes settings for the XMV’s amplifier in

groups of two channels.

Switches 1 through 4 specify the output setting for channels

C and D, and switches 5 through 8 specify the output setting

for channels A and B.

Use these switches to make the following settings. The out-

put signals from the output connectors under each setting are

as follows.

In “Output from each connector,” the meaning of the indica-

tions is as follows: G: ground, Nrm: normal output, Inv:

inverted output, N/A: connection prohibited (not available).

* If this setting is chosen, Double Power mode is turned on

and input/output will be disabled for channels B and D.

 Low impedance connection / high impedance

connection (switches 1 and 5)

These select either a low impedance connection or a high

impedance connection. Set them as appropriate for the

connected speakers and the way in which the speakers are

connected. For details on connections, refer to “High-

impedance and Low-impedance Connections” (page 30).



Impedance (switches 3 and 7)

When using a low impedance connection, set these as

appropriate for the impedance of the speakers that are

connected. Check the specifications of the speakers.

For example if two 8Ω speakers are connected in parallel,

the total impedance will be 4Ω.



Double Power mode (switches 4 and 8)

When a low impedance connection is used, these

switches specify the output of the amplifier. If the 280W

{140W} setting is selected, input/output is enabled for

both channels. If the 560W {280W} setting is selected,

the output from the amplifier will be doubled, but input/

output will be disabled for channels B and D.



70V/100V (switches 2 and 6)

When a high impedance connection is used, these

switches specify the maximum output voltage (Vrms) of

the amplifier.

@6 [SPEAKERS] output connectors

These are barrier strip type speaker output connectors. For

details on how to make connections to a barrier strip, refer to

the “Connections and Setting Up” section entitled “Connect-

ing Speaker Cables” (page 18).

@7 [REMOTE] connector

This is a Euroblock 3-pin connector that allows muting/

unmuting of all channels and power-on/standby to be con-

trolled remotely. For details, refer to “[REMOTE] and

[FAULT OUTPUT] Connectors” (page 21).

@8 [FAULT OUTPUT] connector

This is a Euroblock 3-pin connector that allows an external

device to be notified when a fatal malfunction occurs in this

unit. NC and C will be shorted when the amplifier is operat-

ing normally; NO and C will be shorted when a problem

occurs (page 21).

If a problem occurs, the [PROTECTION] indicator w will

light in orange.

@9 [AC IN] connector

Connect the supplied AC power cord here. First connect the

AC power cord to the connector on the rear panel of this unit,

then plug it into an appropriate AC power outlet.

DIP Switches

Setting Description

RESUME

The unit will start up nor-

mally.

INITIALIZE

The internal memory will be

initialized. For details on the

memory that will be initial-

ized, refer to “Initializing the

Internal Memory” (page 25).

Description

Amplifier

output type

Switches 1–4

(channels C

and D)

Switches 5–8

(channels A

and B)

Output from each

connector

Channels

A and C

Channels

B and D

+–+–

Low-impedance connection

280W{140W},

8Ω

Unbalanced

output

Nrm G G Inv

560W{280W}*,

8Ω

Balanced

output (BTL)

Nrm Inv

N/A N/A

280W{140W},

4Ω

Unbalanced

output

Nrm G G Inv

560W{280W}*,

4Ω

Unbalanced

output

Nrm G

N/A N/A

High-impedance connection

70V,

250W{125W}

Balanced

output (BTL)

Nrm Inv Nrm Inv

100V,

250W{125W}

Balanced

output (BTL)

Nrm Inv Nrm Inv

NOTE

• To change the switch settings, turn off the power to the

unit. If you change the settings while the power is on, the

change will not be effective until you turn the unit off and

then back on again.

• Do not connect negative connectors of different channels.

It may cause the device to malfunction.

• For information on BTL connection, refer to “BTL (Bal-

anced Transformer Less) Connection” (page 31).

CAUTION

Before connecting or disconnecting the power cord,

make sure that the power to the unit is turned OFF.

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Connections and Setting Up

This chapter explains how to set up the XMV to input analog

signals.

If you are using the XMV along with the MTX, refer to the

“MTX Setup Manual.” Refer to this manual for details regard-

ing the following items, even if you are using the XMV along

with the MTX.

• Making settings for speaker output

• Connecting the speaker output connectors

• Making high pass filter (HPF) settings

• Lowering the brightness of the indicators and the display

• Locking the panel

Here we will make and verify the input/output settings as out-

lined below.

 Rack-mounting the Unit

Refer to “Precautions for Rack Mounting” (page 8), and

mount the XMV in your rack.

 Checking the Device Setup DIP Switch Set-

tings

Make sure that all of the rear panel’s device setup DIP

switches (page 13) are in the upward position.

 Connecting the Analog Inputs (Euroblock)

Connect the analog outputs of your mixer or other device to

the analog input connectors (page 15).

You must use the supplied Euroblock plugs with tabs.

If these have been lost, please contact your Yamaha dealer.

Setup for Analog Signal Input

Explanation Page

Rack-mounting the Unit 16

Checking the Device Setup DIP Switch Settings 16

Connecting the Analog Inputs (Euroblock) 16

Making Settings for Speaker Output17

Connecting Speaker Cables 18

Connecting the Power Cord 19

Turning the Power On 19

Enabling Analog Input19

Making High Pass Filter (HPF) Settings 19

Checking the Wiring 20

Lowering the Brightness of the Indicators and the

Display

Locking the Front Panel 20

CAUTION

Steps earlier than “Turning the Power On” must be per-

formed with the power off. If you perform these steps with

the power on, the settings might not be applied, or you

might be subject to electrical shock if you touch the con-

nectors.

12345678

Cable preparation

• To prepare the cable for attachment to a Euroblock

connector, strip the wire as shown in the illustration

using stranded wire to make connections. With a

Euroblock connection, stranded wires may be prone

to breakage because of metal fatigue due to the

weight of the cable or due to vibration. Bundle the

cables and the Euroblock tabs using the supplied

cable ties (page 17). When rackmounting your

equipment, use a lacing bar when possible to bun-

dle and fasten the cables.

• If cables will be frequently connected and discon-

nected, as in the case of a portable installation, we

recommend that you use f

errules

with insulation

sleeves. Use a ferrule whose conductor portion has

an external diameter of 1.6 mm or less, and a length

of approximately 7 mm (such as the AI0,5-6WH

made by the Phoenix Contact corporation).

approx.

7 mm

approx.20 mm

NOTE

Do not tin (plate with solder) the exposed end.

1.6 mm or less

approx.

7 mm

Connections and Setting Up

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

1. Loosen terminal screws.

2. Insert cables.

3. Securely tighten terminal screws.

Pull the cables (not too strongly) to confirm that they are

securely connected.

4. Bundle the cables and the Euroblock tab

using the supplied cable tie.

5. Insert the Euroblock plug into the Analog

input connector of the device.

 Making Settings for Speaker Output

Use the rear panel [SPEAKERS] DIP switches to make the

appropriate settings for the XMV’s speaker output.

The method of connection will differ depending on whether

you’re using a low impedance connection or a high imped-

ance connection.

Low-impedance connection

High-impedance connection

For details, refer to “High-impedance and Low-impedance

Connections” (page 30).

The explanation of the settings is divided into the following

sections.

 When using low impedance connections (page

17)

 When using low impedance connections with

Double Power mode (page 18)

 When using high impedance connections

(page 18)

Since these settings can be made independently for channels

A/B and channels C/D, you can use more than one of the

above methods

 When using low impedance connections

Depending on the impedance (4Ω or 8Ω) of the connected

speakers, set the [SPEAKERS] DIP switches as follows.

NOTE

A slotted screwdriver with a blade width of about 3 milli-

meters is recommended.

NOTE

Trim any excess part of the cable tie as necessary.

Loosen.

Slotted screwdriver

Terminal screw

Euroblock plug

Tab

3 mm or less

–

NOTE

To change the switch settings, turn off the power to the unit.

If you change the settings while the power is on, the change

will not be effective until you turn the unit off and then back

on again.

Setting

Switches 1–4

(channels C and D)

Switches 5–8

(channels A and B)

280W{140W}, 8Ω

280W{140W}, 4Ω

NOTE

If you make settings for low impedance connections, the

HPF will automatically be turned OFF.

8Ω/4Ω

10W 10W 10W 10W 10W

70V/100V

Speaker transformer

Connections and Setting Up

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

The XMV features a switch function between 8Ω and 4Ω to

guarantee the output in case it is connected to a speaker with

an impedance of 8Ω or higher.

If you connect a speaker with an impedance of 8Ω or higher,

set the [SPEAKERS] DIP switches to 8Ω. If you connect a

speaker with an impedance of 4Ω or higher, but lower than

8Ω, set the [SPEAKERS] DIP switches to 4Ω.

 When using low impedance connections with

Double Power mode

If you use Double Power mode, input/output will be dis-

abled for channels B and D.

Depending on the impedance (4Ω or 8Ω) of the connected

speakers, set the [SPEAKERS] DIP switches as follows.

 When using high impedance connections

Depending on the specifications (70V or 100V) of the

system in which this unit is being installed, set the

[SPEAKERS] DIP switches as follows.

 Connecting Speaker Cables

The [SPEAKERS] output connectors (page 15) on the rear

panel are barrier strip type connectors. We will explain con-

nections using a spade lug and connections using a bare con-

ductor.

 If using a spade lug

From below, insert the spade lug all the way, and tighten

the screw.

 If using a bare conductor

Wrap the conductor around the barrier strip terminal as

shown below, and tighten the screw. Be sure that the bare

wire does not touch the chassis.

Total impedance(x) Setting

4Ω x 8Ω4Ω

8Ω x 8Ω

Setting

Switches 1–4

(channel C)

Switches 5–8

(channel A)

560W{280W}, 8Ω

560W{280W}, 4Ω

NOTE

If you make settings for low impedance connections, the

HPF will automatically be turned OFF.

Setting

Switches 1–4

(channels C and D)

Switches 5–8

(channels A and B)

70V

100V

NOTE

When the device is turned on, it will set HPF to 80 Hz, if

the device is set to high impedance connection. If the

device is set to low impedance connection, HPF will be

not set.

CAUTION

Make sure that the power is turned off. If the power is

on, you risk electrical shock.

NOTE

• If the [SPEAKERS] DIP switch 4 (page 15) is in the

lowered position (Double Power mode), even if you do

connect a cable, audio will not be output from channel

• If the [SPEAKERS] DIP switch 8 is in the lowered posi-

tion (Double Power mode), even if you do connect a

cable, audio will not be output from channel B.

•Ensure that tension is not applied to the speaker cable.

• Connect the cables so that the amplifier’s “+” and “-”

symbols match those of the speaker. If they are

reversed, the polarity will be reversed.

TIPS

Since a large amount of current can flow in a speaker

cable, a magnetic field will be generated. If sensitive cir-

cuits such as a microphone input cable or a microphone

amp are located near a speaker cable, electromagnetic

induction may produce noise in the input cable or circuit.

Input cables and devices that contain sensitive circuits

should be kept at a distance from speaker cables; we

also recommend that you fasten the cables in place.

0.15"

(

3.7mm)

0.31"

(

7.8mm)

15mm*

* Actual size Speaker cable

Wire should

not touch

the chassis.

Connections and Setting Up

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Connecting the Power Cord

Connect the included power cord to the [AC IN] connector

(page 15) on the rear panel. First connect the AC power cord

to the connector on this unit, then plug it into an appropriate

AC power outlet.

 Turning the Power On

Use the front panel power switch (page 9) to turn the power

on.

 Enabling Analog Input

Using the front panel, enable analog input as follows.

1. While holding down the [FUNCTION] but-

ton, turn the encoder to make the display

indicate “SRC.”

The control mode will change to “Analog/digital input

selection.”

2. Press the [SELECT] button of the channel

for which you want to enable the analog

input.

The [SELECT] indicator of the selected channel will

light.

3. Take your finger off the [FUNCTION] button,

and turn the encoder to make the display

indicate “ANA.”

Input from the analog input connectors will be enabled.

 Making High Pass Filter (HPF) Settings

If the unit is set for low impedance connections, the HPF

will be OFF. If the unit is set for high impedance connec-

tions, the 80 Hz HPF will be enabled.

If you want to change this setting, proceed as follows.

1. While holding down the [FUNCTION] but-

ton, turn the encoder to make the display

indicate “HPF.”

The control mode will change to “HPF.”

2. Press the [SELECT] button of the channel

for which you want to make HPF settings.

The [SELECT] indicator of the channel whose HPF you

are setting will light.

3. Turn the encoder to select the desired HPF

setting.

The available HPF settings are OFF / 40 Hz / 80 Hz.

CAUTION

You must turn off the power before connecting the

power cord.

CAUTION

Before you turn the power on, make sure that audio

signals are not being input to the analog input connec-

tors. If audio signals are being input, excessive input

will be applied to the speakers when the power is

turned on, possibly damaging the speaker system or

damaging your hearing by high-volume sound. If there

is a problem with the speakers or the wiring, the pro-

tection circuit will operate immediately when the power

is turned on. Check whether there might be a problem

with the wiring.

NOTE

If a certain period of time elapses without any operation

being performed, the unit will return to Attenuation set-

ting operating mode.

NOTE

• In order to protect the amplifier, the HPF cannot be

turned OFF if high impedance connections are used.

•If you’re using a sub-woofer with high-impedance con-

nections, we recommend that you change the HPF

setting to 40 Hz.

•If you’re using a full-range speaker with high-imped-

ance connections, the amplifier’s protection circuit may

operate if the HPF is set to other than 80 Hz. We rec-

ommend that you use the 80 Hz setting.

• If a certain period of time elapses without any opera-

tion being performed, the unit will be placed in Attenua-

tion setting operating mode.

NOTE

If the device is set as follows, the HPF settings will be

changed automatically.

startup

Current startup

HPF

[SPEAKERS]

DIP switches

(page 15)

Device setup

DIP switches 7

and 8 (page 15)

[SPEAKERS]

DIP switches

(page 15)

Hi impedance

RESUME

Low impedance

(changed)

Off

Hi impedance

(not changed)

Same as

the previ-

ous startup

Low impedance

(not changed)

Same as

the previ-

ous startup

Hi impedance

(changed)

80 Hz

(Unrelated to

the setting at

startup)

INITIALIZE

Low impedance Off

Hi impedance 80 Hz

Connections and Setting Up

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Checking the Wiring

Here we’ll explain how to change the attenuation settings

and switch muting on/off, which you will need to do when

checking the wiring.

Before you check the wiring, we recommend that you set the

attenuator of all channels to the lowest setting (-99 dB) to

prevent speaker damage.

To check the wiring, you’ll need to be outputting an audio

signal from the mixer or other device that’s connected to the

analog input connectors.

 Changing the attenuator setting

Here’s how to change the attenuator setting.

1. While holding down the [FUNCTION] but-

ton, turn the encoder to make the display

indicate “ATT.”

2. Press the [SELECT] button of the channel

whose setting you want to adjust.

The [SELECT] indicator of the selected channel will

light.

3. Turn the encoder to gradually raise the

attenuator setting from -99, and verify

that sound is produced from the speaker.

 Switching the mute setting on/off

While holding down the [MUTE] button,

press the [SELECT] button of the channel

that you want to control.

When mute is on, the [MUTE] indicator will light; when

mute is off, the [MUTE] indicator will be unlit.

 Lowering the Brightness of the Indicators

and the Display

If the front panel LED indicators are too bright, you can

lower their brightness.

After turning the power off, set the rear panel device setup

DIP switch 4 (LED DIMMER) to the lower position (ON).

The next time you turn the power on, the unit will start up

with decreased indicator brightness.

 Locking the Front Panel

By locking the panel you can disable front panel operations

other than controlling the power (front panel lock).

When this unit is used as part of an installed system, you can

lock down the settings by disabling operations from the front

panel, thus preventing inadvertent changes.

After turning the power off, set the rear panel device setup

DIP switch 5 (PANEL LOCK) to the lower position

(LOCK). The next time you turn the power on, the unit will

start up with the front panel locked.

Even in the locked state, you can temporarily defeat the

panel lock by pressing the [FUNCTION] button and the

[SELECT] A button. However, it will be re-locked when any

of the following conditions occur.

• One minutes elapses without any operation being per-

formed after the panel is temporarily unlocked

• You press the [FUNCTION] button and the [SELECT] A

button

• You turn the power off

The lock status is shown by the front panel [PANEL LOCK]

indicator.

• Locked: lit

• Not locked: unlit

• Temporarily unlocked: flashing

NOTE

If the speakers are remotely located and you are unable to

check the signal output easily, changing the [SIGNAL] indi-

cator (page 10) setting to “output” will allow you to check

whether current is flowing to the speakers. For details on

switching the indicator setting, refer to “Front Panel Opera-

tions” (page 23).

NOTE

The brightness of the [POWER] indicator will not be

reduced.

Connections and Setting Up

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

This chapter explains how to use and connect the [REMOTE]

connector and [FAULT OUTPUT] connector located on the rear

panel of the XMV.

 Using the [REMOTE] Connector

(Euroblock 3-pin)

You can connect switches to the rear panel [REMOTE] connec-

tor (page 15), and use them to remotely mute/unmute all chan-

nels or switch the power standby/on status.

From the left, the [REMOTE] connector consists of MUTE

ALL, STANDBY, and GND pins.

The [REMOTE] connector uses a Euroblock plug.

For details on how to connect Euroblock plugs, refer to “Con-

necting the [REMOTE] Connector or [FAULT OUTPUT] Con-

nector” (page 22).

•Muting/unmuting all channels

•Switching the power standby/on status

 Using the [FAULT OUTPUT] Connector

(Euroblock 3-pin)

A lamp or other indicator can be connected to the rear panel

[FAULT OUTPUT] connector to inform an operator when a

problem occurs.

The [FAULT OUTPUT] connector (page 15) consists of NO

(Normally Open), C (Common), and NC (Normally Closed)

pins. The [FAULT OUTPUT] connector is a relay circuit that

operates as follows.

The [FAULT OUTPUT] connector uses a Euroblock plug. For

details on how to connect Euroblock plugs, refer to “Connecting

the [REMOTE] Connector or [FAULT OUTPUT] Connector”

(page 22).

[REMOTE] and [FAULT OUTPUT] Con-

nectors

Turning mute on Turning mute off

NOTE

When all channels are muted via the [REMOTE] connector,

the [MUTE] button on the front panel cannot be operated.

Switching the power to

standby

Turning the power on

NOTE

When the power is set to standby via the [REMOTE] con-

nector, turning on the power switch will place the unit in

standby mode.

Normal state

Fault condition

Power off

NO Open Closed Closed

NC Closed Open Open

Example: Using an LED to indicate the

XMV’s normal/fault status

CAUTION

The rated load of the relay contacts is 1A, DC 30 V for a

resistive load.

Do not apply a load that exceeds this rating.

 Normal state

 Shut-down state

Lit

Unlit

Lit

XMV

Connections and Setting Up

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Connecting the [REMOTE] Connector or

[FAULT OUTPUT] Connector

You must use the supplied Euroblock plugs when making con-

nections to the [REMOTE] connector or [FAULT OUTPUT]

connector.

If these have been lost, please contact your Yamaha dealer.

1. Loosen terminal screws.

2. Insert cables.

3. Securely tighten terminal screws.

Pull the cables (not too strongly) to confirm that they are

securely connected.

4. Insert the Euroblock plug into the [REMOTE]

connector or [FAULT OUTPUT] connector of

the device.

Cable preparation

• To prepare the cable for attachment to a Euroblock

connector, strip the wire as shown in the illustration

using stranded wire to make connections. With a Euro-

block connection, stranded wires may be prone to

breakage because of metal fatigue due to the weight of

the cable or due to vibration.

•If cables will be frequently connected and discon-

nected, as in the case of a portable installation, we

recommend that you use ferrules with insulation

sleeves. Use a ferrule whose conductor portion has an

external diameter of 1.3 mm or less, and a length of

approximately 5 mm (such as the AI0,5-6WH made by

the Phoenix Contact corporation).

NOTE

A slotted screwdriver with a blade width of about 3 millime-

ters is recommended.

approx.

5 mm

NOTE

Do not tin (plate with solder) the exposed end.

1.3 mm or less

approx.

5 mm

Loosen.

Terminal

screw

Slotted screwdriver

Euroblock plug

3 mm or less

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Operations

This chapter describes the operations you can perform from the

front panel.

 Basic Operations

*1: “X+Y” means “operate Y while operating X.” For example, “[SELECT] A + encoder” means that you should hold down the [SELECT] A

button and operate the encoder.

Front Panel Operations

NOTE

If you modify the parameter settings, do not turn the power

switch OFF for at least one second. Otherwise, the changes to

the settings may be lost.

To do this... Operation Description

Checking the current operat-

ing mode

[FUNCTION]

While you hold down the [FUNCTION] button, the current oper-

ating mode will be shown in the display. The modes are indi-

cated as follows.

Changing the operating mode [FUNCTION] + encoder

Use the encoder to change the operating mode.

When you release the [FUNCTION] button, the operating mode

shown at that time will be selected; the display will show the

parameter value.

If a certain period of time elapses without any operation being

performed, the operating mode will be switched back to “Atten-

uation setting.”

Turning Mute on/off

[MUTE] + [SELECT] (of the chan-

nel to be muted)

When muting turns on, the [MUTE] indicator of the selected

channel will lit.

When muting turns off, the [MUTE] indicator will go unlit.

Temporarily disabling or re-

enabling front panel lock

[FUNCTION] + [SELECT] A

When front panel lock is temporarily disabled, the [PANEL

LOCK] indicator will flash.

When front panel lock is enabled, the [PANEL LOCK] indicator

will lit. While the front panel is locked, “LC” is shown in the dis-

play.

Even if front panel lock is temporarily disabled, it will be

relocked when one minute passes without any operation being

performed or when the power is turned off.

Indication Operating mode

ATT Attenuation setting

POL Polarity setting

HPF

Turn the high pass filter on/off and

change the cutoff frequency

SRC Analog/digital input selection

SIG [SIGNAL] indicator display selection

DIS Digital input sensitivity selection

Operations

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Parameter Operations

*2: “XY” means “operate X, and then operating Y.” For example, “[SELECT] A  encoder” means that you should press the [SELECT]

A, and then operate the encoder.

To do this...

Operating mode

(indication)

Operation Description

Changing the attenuator

value (volume)

attenuator

(ATT)

[SELECT] (of the channel to

be changed)  encoder

The [SELECT] indicator of the selected channel

will lit, and the attenuator value can be edited by

the encoder.

The range of adjustment is -99 dB–0 dB in 1 dB

steps.

Changing the polarity

polarity

(POL)

[SELECT] (of the channel to

be changed)  encoder

The [SELECT] indicator of the selected channel

will light, and the polarity can be changed by using

the encoder.

Changing the high pass fil-

ter (HPF) cutoff frequency

Turning off the high pass

filter (HPF)

HPF

(HPF)

[SELECT] (of the channel to

be changed)  encoder

The [SELECT] indicator of the selected channel

will light, and the high pass filter (HPF) on/off set-

ting and cutoff frequency can be changed by using

the encoder. This will be set to 80 Hz if a high

impedance connection is specified; it will be turned

OFF if a low impedance connection is specified.

In order to protect the amplifier, the HPF of the

selected channel cannot be turned OFF if a high

impedance connection is specified.

Switching between analog/

digital input

analog/digital input

selection

(SRC)

Encoder operation

The [SELECT] indicator of the selected channel

will light, and you can use the encoder to change

the analog/digital input selection.

Do not select “analog” if your audio network has

been configured using the [YDIF] connectors or

Dante [PRIMARY]/[SECONDARY] connectors.

Selecting “analog” will interrupt audio transmission

to and from the devices that are connected via the

YDIF connectors or Dante connectors.

Switching whether the

[SIGNAL] indicators are

used for input or for output

[SIGNAL] indicator

switching

(SIG)

Enco

der opera

tion

Use the encoder to specify whether the [SIGNAL]

indicators will show the input signal level or the out-

put signal level.

Digital input sensitivity

selection

* Digital input sensitivity: the

digital input level at which

the input attenuator is 0 dB

(volume maximum) and the

amplifier is at maximum

output; refer to “Block Dia-

gram” (page 236).

digital input

sensitivity

(DIS)

Encoder operation

Use the encoder to change the digital input sensi-

tivity setting. To prevent inadvertent setting, the

value does not change right away when the

encoder is turned. Until the input sensitivity

changes, “

–––” appears in the display.

Indication Polarity

NOR Normal polarity

INV Inverted polarity

Indication Meaning

OFF HPF is off

H40 Cutoff frequency is 40 Hz

H80 Cutoff frequency is 80 Hz

Indication Input connectors

ANA Analog input connectors

DIG

[YDIF] connectors

(XMV4280/XMV4140)

Dante [PRIMARY]/

[SECONDARY] connectors

(XMV4280-D/XMV4140-D)

Indication Lit condition

IN Input

OUT Output

Indication Digital input sensitivity

D20 -20 dBFS

D03 -3 dBFS

–––

(value in process of being

changed)

Operations

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Execute the following procedure when you return the internal

memory settings to their factory set state (initialize the internal

memory), such as when the amplifier has been moved to a dif-

ferent location.

1. Turn off the power.

2. Set device setup DIP switch 7 to the down-

ward position and switch 8 to the upward

position.

3. Turn on the power. The initializing operation

will start.

• In the case of the XMV4280/XMV4140

During initialization, the [NETWORK], [YDIF], and

[PANEL LOCK] indicators will flash. When initialization

is complete, the [NETWORK] and [YDIF] indicators will

flash.

• In the case of the XMV4280-D/XMV4140-D

During initialization, the [PRIMARY], [SECONDARY],

[SYNC] (green), [SYNC] (orange) and [PANEL LOCK]

indicators will flash. When initialization is complete, the

[PRIMARY], [SECONDARY] and [SYNC] (green) indi-

cators will flash.

If the unit fails to initialize, the [POWER] indicator will

light, the [ALERT] indicator will flash, and other indica-

tors will turn off. Please contact your Yamaha dealer.

4. Make sure the initializing operation is com-

plete and turn off the power.

5. Set device setup DIP switches 7 and 8 to the

upward position (RESUME).

6. Turn on the power.

The following parameters held in memory are initialized.

• Attenuator values

• Polarity settings

• HPF settings

• Analog/digital input setting

• [SIGNAL] indicator display setting

• Event log

* When the unit is shipped from the factory, the device setup

DIP switches are all in the upward position.

Initializing the Internal Memory

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Appendix

* If taking the above steps does not solve the problem, contact your Yamaha dealer for repair.

The Yamaha Pro Audio website provides a FAQ (a list of frequently asked questions, with answers).

http://www.yamahaproaudio.com/

Troubleshooting

Symptom Possible causes Possible solution

The power won’t turn on The power cord is disconnected Connect the power cord.

No sound is heard

The analog/digital input setting is

incorrect

From the front panel, check the analog/digital

input setting.

Double Power mode is selected

In Double Power mode, no audio signals will be

output from channel B or channel D. Either turn

off Double Power mode, or re-connect the cables.

An input/output cable is discon-

nected

Connect the input/output cables. Also, make sure

that the cables are securely connected.

The mute fu nction is turned on

Make sure that the [MUTE] indicator is unlit. If it is

lit, turn Mute off.

The attenuator value is too low

Change

to “Attenuation setting” (page 23), and

check whether the attenuator value is appropriate

on the display (page 10).

No audio signal is being input

Make sure that an audio signal is being output

from the mixer or other device that is outputting

audio to the XMV.

The protection circuit has operated

(the [PROTECTION] indicator is lit)

Turn off the power, wait for the XMV to cool, and

then turn the power on again.

The unit is in standby mode

(the [POWER] indicator is flashing)

Make sure that the switch connected to the

[REMOTE] connector is turned on. Alternatively,

use the editor to check that this is turned on.

Some abnormality has occurred at

digital input from the MTX

(on XMV4280/XMV4140: [YDIF]

indicator is unlit; on XMV4280-D/

XMV4140-D: green [SYNC] indica-

tor is unlit)

Check the MTX. For details, refer to MTX manu-

als

“Analog” input has been selected on

a device that is connected via a

YDIF connector

(XMV4280/XMV4140 only)

Select “digital” input on the device. If you wish to

use the device for analog input, disconnect the

device from the YDIF network.

The [ALERT] indicator remains

flashing or lit even after you’ve

turned the power on/off

The device has failed

The device has failed. Contact your Yamaha

dealer for repair.

Appendix

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

If a problem occurs in the XMV, the [ALERT] indicator will flash and an alert number will appear in the display.

The alert numbers, the corresponding content, and the appropriate actions are listed below.

Alert Numbers and Content

Alert number Meaning Response

No display

(only [ALERT] is lit)

The device has not started up correctly.

Turn the power off, then turn on after waiting at least 5

seconds. If this does not solve the problem, please ini-

tialize the memory. Should this also fails, contact your

Yamaha dealer.

001.–008.

010.

The internal backup battery has been completely

exhausted or is not installed.

When you turn off the power, the current settings will be

lost, and will return to the default values. Please stop use

immediately, and contact your Yamaha dealer.

011.

The internal backup battery has run extremely low, and

it is possible that the internal memory has been cleared.

012.

The internal backup battery has only a small amount of

power remaining.

This does not affect the operation of the device. How-

ever, if y

ou continue using the device, the settings may

be lost and reset to the default values. Contact your

Yamaha dealer as soon as possible.

013.

A problem has occurred with the internal clock, and it

has been initialized (January 1, 2000, 0:00)

If this occurs each time you turn on the power, it is possi-

ble that the internal backup battery has run down or that

the device has malfunctioned. Contact your Yamaha

dealer.

If this occurs only once, an abnormality was detected

with the clock setting and it was initialized; use the editor

to set the time.

015. The settings saved in internal memory have been lost.

Either the internal backup battery has run low, or the

device has malfunctioned

. Cont

act your Yamaha dealer.

016. A memory problem has occurred. Contact your Yamaha dealer.

021. The word clock master has become unlocked.

Make sure that the word clock signal is being input cor-

rectly.

022.

The digital signal being input to the [YDIF IN] connector

is not synchronized to the word clock of this device.

Make sure that YDIF cables are properly connected.

Use cables that meet the required specifications.

023.

The digital signal being input to the [YDIF IN] connector

is not continuously synchronized to the word clock of

this device.

030.

There is a problem with the connection of the [YDIF IN]

connector.

Make sure that YDIF cables are properly connected.

Use cables that meet the required specifications.

040. Duplicate IP addresses.

Change the IP addresses so that there are no dupli-

cates.

041. IP address was not set within 60 seconds of startup.

Please check rear panel DIP s

witch 6 (IP Set

ting). If D

switch 6 is set to “PC,” use the editor or DHCP server to

specify the device IP address.

043. Too many devices are connected to the network.

Reduce the number of devices connected to the net-

work.

046. Dante transmission flow count exceeded the limit.

Maximum Dante Flow rate exceeded. Try changing parts

of transmission flows to Multicast using Dante Controller.

050. The UNIT ID is set to “00.” Set the UNIT ID to something other than “00.”

051.

Devices with identical UNIT IDs were found connected

within the same network.

Change the UNIT ID so that there are no duplicates.

072.

Because this device has Dante Device Lock enabled,

the settings of device DIP switches and MTX-MRX Edi-

tor do not match current Dante settings.

If you have Dante Device Lock enabled, please disable

using Dante Controller, review device DIP switch settings

and MT

X-MRX Editor

’s Dante settings, and edit as nec-

essary to match the current situation.

100.

The power supply was shut down because d.c. was

detected on a speaker output.

It is likely that the device has malfunctioned; immediately

stop using the device and contact your Yamaha dealer.

Appendix

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

101.

The power supply was shut down because its tempera-

ture exceeded the allowed limit.

Turn the power off, let the power supply cool down, then

turn the power on again.

Continuous high-power output will cause high tempera-

tures, so please lower the output level. If the temperature

is still high, check whether dirt or a foreign object could

have clogged the cooling fan, and clean the fan if neces-

sary.

103.

Protection has been activated, and the power supply

was shut down.

Continuous high-power output ma

y have ac

tivated pro-

tection; lower the output level.

For details on the reason that protection was activated,

refer to “[PROTECTION] A/B/C/D indicators” (page 9).

104. Protection has been activated, and muted.

105.

A short circuit was detected in the speaker output con-

nector, so the output signal has been muted.

It may be that the speaker output connector’s “+” and “-”

are shorted, or that the connected speaker has malfunc-

tioned.

106.

The temperature of the amp section (heat sink) has

changed, and the speaker output is now ****.

**** = 0dB and OK

-1dB and in protection

muted and in protection

Continuous high-power output will cause high tempera-

tures, so please lower the input level or attenuator. If the

temperature is still high, check whether dirt or a foreign

ject could have clogged the cooling fan’s air intake,

and clean it if necessary.

110.

The Redundant Backup function has been activated,

and the input signal has been switched.

There is a problem in the digital signal. Check the digital

line connection and check whether the pilot tone is being

input.

Alert number Meaning Response

Appendix

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Warnings and certain other types of information are displayed via the XMV4280-D/XMV4140-D front panel indicators.

Messages are also displayed in the Dante Controller Error Status field.

Each indicator lights or flashes as described below:

 Information Messages

The status is shown by the lit/flashing state of the indicator.

If the orange [SYNC] indicator is unlit, the unit is operating normally.

If the green [SYNC] indicator is unlit, the unit’s clock is unconfirmed.

 Warning Messages

The indicator will remain lit or continue flashing cyclically until the problem is solved.

If the green [SYNC] indicator is unlit, the unit’s clock is unconfirmed.

If the green indicator is flashing, the unit is the clock master.

If the green indicator is lit, the unit is the clock slave and the clock is synchronized.

Dante Messages (XMV4280-D/XMV4140-D only)

Unlit The indicator is off.

Lit The indicator remains lit steadily.

Flash The indicator continues to flash.

Flash x 2 The indicator flashes twice cyclically.

SYNC Indicators Description Explanation

Synchronization is occurring.

Please wait until the unit synchronizes

completely. It may take approximately 60

seconds for synchronization to be com-

pleted.

The unit is functioning correctly as the word clock

master.

The unit is operating as the word clock

master.

The unit is functioning correctly as the word clock

slave.

The unit is operating as the clock slave

and the clock is synchronized.

SYNC Indicators Description Possible Solution

The word clock is not set correctly.

Set the clock master and sampling fre-

quency correctly on the MTX-MRX Editor

or in Dante Controller.

Dante Network circuit is broken.

Make sure that the Ethernet cables are

not removed or short-circuited.

SYNC Indicators Description Possible Solution

A non-GbE-compatible device is connected.

When transferring audio via Dante, use

device that supports GbE.

The Dante [SECONDARY] connector has taken

over communications during redundant network

operation.

Check the circuit connected to the Dante

[PRIMARY] connector.

An abnormality has occurred on the circuit con-

nected to the Dante [SECONDARY] connector dur-

ing redundant network operation.

Check the circuit connected to the Dante

[SECONDARY] connector.

(green) Unlit

(orange) Lit

(green) Flash

(orange) Unlit

(green) Lit

(orange) Unlit

(green) Unlit

(orange) Flash

(green) Unlit

(orange) Flash x2

(green) Lit or flash

(orange) Lit

(green) Lit or flash

(orange) Flash

(green) Lit or flash

(orange) Flash x 2

Appendix

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

For a high-impedance connection a speaker transformer that

raises the impedance to several hundred or thousand ohms is

added to the speaker system. This allows the speaker system to

be effectively driven with much lower current than is required

for a low-impedance system. That, in turn, makes it possible to

connect a larger number of speaker systems to each power

amplifier output. High-impedance speaker connections work at

a specific maximum voltage—usually 70 or 100 volts—and are

therefore also referred to as “constant voltage” speaker systems

(the label “constant voltage” is somewhat misleading: the actual

output voltage fluctuates according to the input signal).

For a low-impedance speaker connection, the power amplifier is

directly connected to a speaker system that has an inherent

impedance of 4–16Ω.

The difference between these types of connection are outlined

below.

 Multiple Speaker System Drive Capability

 High impedance

As long as the total nominal power input rating for all

speakers is within the power output capability of the

amplifier, any number of speaker systems can be con-

nected in parallel. In a high-impedance installation, the

power input rating is determined by the speaker trans-

formers used.

If the 280W output XMV4280 is used with a speaker sys-

tem having speaker transformers that make the rated

input 10W, you can connect a speaker system with a max-

imum of 24 speakers per channel based on the calculation

(*), giving you a total of up to 96 speakers for the four

channels. In a high-impedance installation it is also possi-

ble to simultaneously drive speaker systems that have dif-

ferent input power ratings.

(*) Yamaha recommends that you allow a 20% margin to

this number, considering variations in the trans-

former’s primary impedance, possible tap changes in

the future, and the addition of speakers.

 Low impedance

Normally only one speaker system is connected to each

amplifier channel, as shown in the diagram.

This means that the number of speaker system that can be

connected to an XMV is limited to four.

However, even with low impedance connections, there is

a way by which multiple speaker systems can be con-

nected to one channel.

When multiple speakers systems having the same imped-

ance are connected in parallel, the total impedance

becomes the individual speaker system impedance

divided by the number of systems connected. This means

that if the XMV is set to 4Ω, up to two 8Ω speaker sys-

tems can be connected to one channel.

The second method is series connection. In this case the

total impedance is simply the sum of the impedances of

the speaker systems connected. But as you can see in the

series connection wiring diagram, if one speaker system

fails the second speaker system will be affected as well.

High-impedance and Low-impedance

Connections

10W 10W 10W 10W 10W

70V/100V

Speaker transformer

4Ω

8Ω 8Ω 8Ω

Total impedance = 4Ω

Cannot be

connected

4Ω

Interruption

Total impedance

= 8Ω

Failure

No sound

Appendix

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Transmission Distance and Efficiency

The cables that transmit electric signals have resistance. The

resistance in short cables is small enough that it can be

ignored, but as transmission distance and cable length

increase, resistance can increase to the point that signal loss

and degradation occur. That can mean reduced output level

and sound quality. Below we examine the merits and demer-

its of low-impedance and high-impedance connections in

relation to transmission over significant distances.

 High impedance

Even if the cable resistance reaches 8Ω due to an

extended transmission distance, this is an amount that can

be ignored relative to the impedance of the speaker sys-

tem, meaning that transmission loss due to the cable will

be insignificant, and thus will have little effect on the

transmission efficiency of the electrical signal.

 Low impedance

For short distances over which cable resistance is insig-

nificant, low-impedance connection allows the power

amp to be directly connected to the speaker system with-

out the need for speaker transformers. That means that

the full performance potential of amp and speakers can be

taken advantage of for sound quality that is superior to

high-impedance installations. And since only one speaker

system is usually connected to each amplifier channel,

different audio signals can be sent to each speaker sys-

tem, or “zone,” as required.

But in a situation like the one shown in the diagram,

where a long cable with a resistance of 8Ω is required,

transmission loss will theoretically result in the output

level being reduced by half because the impedance of the

speaker system itself is only 8Ω. Half of the power gets

absorbed by the cable, and only the remaining half is

available to drive the speaker. So for low-impedance

installations it is necessary to either keep the cables short

enough that cable resistance is not an issue, or use thicker

cables that have lower resistance for longer runs, for

example.

BTL connection doubles the output power since the two ampli-

fier channels are used as one amplifier.

70V/100V

Long distance

Cable resistance

(round-trip

distance) = 8Ω

Speaker

transformer (1kΩ)

Almost 100%

8Ω

Long distance

Cable resistance

(round-trip

distance) = 8Ω

Speaker system

inpedance = 8Ω

50%

BTL (Balanced Transformer Less) Con-

nection

NOTE

Since the amplifier outputs are connected to both the plus con-

nector and the minus connector, contact with the other connec-

tors or the chassis may result in malfunction.

Normal amplifier

Inverted amplifier

Normal connection

BTL connection

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

234

Specifications

General Specifications

XMV4280 XMV4140 XMV4280-D XMV4140-D

Output Power

1kHz, THD+N=1%

(20 ms Burst)

4 Ω 280W 140W 280W 140W

8 Ω280W 140W 280W 140W

4 Ω / DOUBLE POWER MODE 560W 280W 560W 280W

8 Ω / DOUBLE POWER MODE 560W 280W 560W 280W

High Impedance 100V (RL=40Ω/XMV4280)

(RL=80Ω/XMV4140)

250W 125W 250W 125W

70V (RL=20Ω/XMV4280)

(RL=40Ω/XMV4140)

250W 125W 250W 125W

Amplifier Type (Output Circuitry) Class D

THD+N 1kHz, half power, 4Ω

All channel output

0.2%

1kHz, half power, 100V, 70V

All channel output

0.2%

Frequency Response 1W, 280W/8Ω, 20Hz–20kHz (XMV4280)

0dB, ±1.0dB1W, 140W/8Ω, 20Hz–20kHz (XMV4140)

1W, 100V/70V, 55Hz–20kHz

Crosstalk 1kHz, half power, 8Ω

Att. max, input 150Ω shunt

-60dB

Residual Noise A-weighted

280W, 8Ω

-65dBu

S/N Ratio A-weighted

280W o

r 140W mode

100dB

Inpu

t Sensitivity +4 dBu (1.23V)

Voltag e Gain 100V 38.2dB 38.2dB 38.2dB 38.2dB

70V 35.2dB 35.2dB 35.2dB 35.2dB

280W (140W)/8Ω 31.7dB 28.7dB 31.7dB 28.7dB

560W (280W)/8Ω 34.7dB 31.7dB 34.7dB 31.7dB

Load Protection Power switch on/off Mute the output

DC-fault Power supply shutdown

Amplifier Protection Thermal Mute the output (heatsink temp. 90°C) (return automatically.)

Overcurrent Mute the output (return automatically.)

Low load impedance Mute the output (return automatically.)

Power Supply

Protection

Thermal Power suppl

y shutdown (h

eatsink temp. 100°C)

Integrated power Gain reduction (return automatically.)

Limiter Circuit Clip limiting Cilp limiter

Cooling 3 speed fan x 2, front-to-back airflow

Maximum Input Level +24dBu

Input Impedance 20kΩ (balanced)

10kΩ (unbalanced)

Sampling Frequency 48kHz

A/D, D/A Converters AD: 24-bit linear, 128 times over sampling

DA: 24-bit linear, 128 times over sampling

Signal Processing 32 bit digital signal processing

Latency Analog input  [SPEAKERS] output1.85msec

[YDIF] input 

[SPEAKERS] output (fs=48kHz)

1. 0 8msec —

[YDIF] input 

[SPEAKERS] output (fs=44.1kHz)

1. 1 7 m s e c —

ante [PRIMAR

Y]/[SECONDARY] input 

[SPEAKERS] output (fs=48kHz, Dante

latency setup = 0.25msec)

— 1.33msec

Dante [PRIMARY]/[SECONDARY] input 

[SPEAKERS] output (fs=44.1kHz, Dante

latency setup = 0.25msec)

— 1.42msec

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

235

Specifications

 [SIGNAL] Indicator Lit Level

XMV4280 XMV4140 XMV4280-D XMV4140-D

Controls Front panel Power switch (rocker), Rotary encoder x 1,

[FUNCTION] button x 1, [SELECT] button x 4, [MUTE] button x 1

Front panel (software) ATT (-99dB to 0dB, 1dB step), POLARITY,

HPF (OFF, 40Hz, 80Hz),

*40Hz or 80Hz for Hi-Z output setup

INPUT SOURCE (ANALOG/DIGITAL), SIGNAL LED (INPUT/OUTPUT)

Rear panel

AMP SETTING switch (OUTPUT FORMAT,

IMPEDANCE, DOUBLE POWER MODE,

HI-Z LEVEL, per 2 channels),

SETUP switch (UNIT ID, LED DIMMER,

PANEL LOCK, IP SETTING, START UP

MODE), Rotary switch (UNIT ID)

AMP SETTING switch (OUTPUT FORMAT,

IMPEDANCE, DOUBLE POWER MODE,

HI-Z LEVEL, per 2 channels),

SETUP switch (SECONDARY PORT,

LED DIMMER, PANEL LOCK,

IP SETTING, START UP MODE),

Rotary switch x 2 (UNIT ID HIGH,

UNIT ID LOW)

Connectors Analog inputEuroblock (5.08mm pitch, balanced) /ch

Digital I/O RJ45 x 2 ([YDIF] IN/OUT)

RJ45 x 2 (Dante [PRIMARY]/[SECONDARY])

Speakers Barrier strip /ch

Network RJ45 x 1 —

Remote Euroblock (3.50mm pitch) x 1

Fault outputEuroblock (3.50mm pitch) x 1

Power AC inlet x1

Indicators

[POWER] x 1 (green),

[ALERT] x 1 (red),

[PANEL LOCK] x 1 (orange),

[PROTECTION] x 4 (orange),

[LIMIT] x 4 (red),

[MUTE] x 4 (yellow),

[SIGNAL] x 4 (green),

[SELECT] x 4 (green),

[NETWORK] x 1 (green),

[YDIF] x 1 (green)

[POWER] x 1 (green),

[ALERT] x 1 (red),

[PANEL LOCK] x 1 (orange),

[PROTECTION] x 4 (orange),

[LIMIT] x 4 (red),

[MUTE] x 4 (yellow),

[SIGNAL] x 4 (green),

[SELECT] x 4 (green),

[PRIMARY] x 1 (green),

[SECONDARY] x 1 (green),

[SYNC] x 2 (green, orange)

Display 3 digit, 7 segment numeric display

AC Power Requirement 100V, 120V, 230V–240V 50Hz/60Hz

Power

Consumption

1/8 MAX power, (4Ω) 250W 150W 250W 150W

Idle (4Ω) 37W 37W 37W 37W

Standby18.5W 18.5W 18.5W 18.5W

Operating Temperature 0°C to +40°C

Storage Temperature -20°C to +60°C

Dimensions (W x H x D, including knob) 480 x 88 x 422 mm (18.9 x 3.5 x 16.6 inches)

Net Weight 8.1 kg (17.9 lbs)

Included Accessories AC power cord (2.5m) x 1, E

uroblo

ck plug (3-pin, 3.50mm pitch) x 2,

roblock plug with tabs (3-pin, 5.08mm pitch) x 4, Cable tie x 4, Owner’s Manual x 1

Optional Accessories —

XMV4280/XMV4280-D

Lit level

dBu Vrms W

100V 8.7 2.11 —

70V 5.6 1.48 —

560W/8Ω 5.2 1.41 0.249

560W/4Ω 2.2 1.00 0.250

280W/8Ω 2.2 1.00 0.125

280W/4Ω -0.8 0.71 0.125

XMV4140/XMV4140-D

Lit level

dBu Vrms W

100V 8.7 2.11 —

70V 5.6 1.48 —

280W/8Ω 2.2 1.00 0.125

280W/4Ω -0.8 0.71 0.125

140W/8Ω -0.8 0.71 0.063

140W/4Ω -3.8 0.50 0.063

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

236

Specifications

Block Diagram

Dimensions

Dante

PRIMARY

SECONDARY

YDIF

Out

Dante model only

YDIF model only

LIMITERMUTE

OFF

HPF

POLARITY

LIMITPROTECTION

AMP PROTECTION LOGIC

TEMP

DSP

XMV Series Block Diagram

SETUP

AMP

70V

ALERT

-20dBFS

DIGITAL INPUT

SENSITIVITY

Dante

Redundancy

INPUT

SOURCE

SELECT

INPUT REDUNDANCY

Backup Mode

Override Mode

Balanced

Unbalanced *3

Balanced

Unbalanced *3

YDIF model: XMV4140, XMV4280, XMV8140, XMV8280

Dante model: XMV4140-D, XMV4280-D, XMV8140-D, XMV8280-D

CH A, B, C, D

(E, F, G, H for XMV8xxx)

ATT

-3dBFS

SIGNAL (IN)

80Hz

40Hz

DC-FAULT

SIGNAL

(OUT)

100V

8ohms

4ohms

8ohms

4ohms

Double Power mode:

Only Speakers A, C

(E, G for XMV8xxx)

SPEAKERS A, C

(E, G for XMV8xxx)

(BTL)

SPEAKERS B, D

(F, H for XMV8xxx)

(BTL)

*1: By pilot tone detection with 1/24

octave band frequencies

*2: Balanced (BTL)

• 560W{280W}, 8Ω <D>

• 70V, 250W{125W}

• 100V, 250W{125W}

*3: Unbalanced

• 560W{280W}, 4Ω <D>

• 280W{140W}, 8Ω

• 280W{140W}, 4Ω

<D>: Double Power mode (Channels B, D, F and H are disabled.)

OUTPUT

CURRENT

LOAD

IMPEDANCE

OUTPUT

VOLTAGE

INTEGRAL

OUTPUT

POWER

INV

AMP

INV

AMP

430

422

414

409

3823

2.5

480

76.2

463

11x6.5

480

76.2

463

11x6.5

Unit: mm

(XMV4280/XMV4140)

(XMV4280-D/XMV4140-D)

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

237

Specifications

 XMV4280/XMV4280-D

Power Specifications (PINK NOISE, 100V/50Hz mains)

Power Specifications (PINK NOISE, 120V/60Hz mains)

Current Draw and Heat Dissipation

MODE Line Current (A)

Power

Consumption (W)

Watts

Dissipated (W)

Heat Dissipation

Btu/h kcal/h

standby

280W/4Ω

0.315155113

280W/8Ω

560W/4Ω

560W/8Ω

100V

70V

idle

280W/4Ω 0.5 37 37 127 32

280W/8Ω 0.5 37 37 127 32

560W/4Ω 0.4 31 31 106 27

560W/8Ω 0.5 36 36 124 31

100V 0.6 48 48 165 41

70V 0.6 48 48 165 41

1/8 output

power

280W/4Ω 2.2 218 78 268 67

280W/8Ω 2.0 203 64 218 55

560W/4Ω 2.2 214 75 256 64

560W/8Ω 2.2 211 71 244 61

100V 2.0 190 65 223 56

70V 2.1 196 71 244 61

1/3 output

power

280W/4Ω 5.2 499 123 422 106

280W/8Ω 4.9 470 97 332 84

560W/4Ω 5.0 48511338697

560W/8Ω 5.2 505 131 449 113

100V 4.3 416 84288 73

70V 4.6 445 106 364 92

MODE Line Current (A)

Power

Consumption (W)

Watts

Dissipated (W)

Heat Dissipation

Btu/h kcal/h

standby

280W/4Ω

0.315155113

280W/8Ω

560W/4Ω

560W/8Ω

100V

70V

idle

280W/4Ω 0.4 37 37 127 32

280W/8Ω 0.4 37 37 127 32

560W/4Ω 0.4 31 31 106 27

560W/8Ω 0.4 36 36 124 31

100V 0.5 48 48 165 41

70V 0.5 48 48 165 41

1/8 output

power

280W/4Ω 1.9 218 78 268 67

280W/8Ω1.8 203 64 218 55

560W/4Ω 1.9 214 75 256 64

560W/8Ω 1.9 211 71 244 61

100V 1.6 190 65 223 56

70V 1.7 196 71 244 61

1/3 output

power

280W/4Ω 4.3 499 123 422 106

280W/8Ω 4.1 470 97 332 84

560W/4Ω 4.2 48511338697

560W/8Ω 4.3 505 131 449 113

100V 3.6 416 8328471

70V 3.8 445 112 38396

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

238

Specifications

Power Specifications (PINK NOISE, 230V/50Hz mains)

1/8 power is typical of program material with occasional clipping. Refer to these figures for most applications.

1/3 power represents program material with extremely heavy clipping.

Test signal: Pink Noise, bandwidth limited from 22Hz to 22kHz

All channels driven

1W = 0.860kcal/h, 1BTU = 0.252kcal

Note that Line Voltage [V] x Line Current [A] = [VA], not equals to [W].

 XMV4140/XMV4140-D

Power Specifications (PINK NOISE, 100V/50Hz mains)

MODE Line Current (A)

Power

Consumption (W)

Watts

Dissipated (W)

Heat Dissipation

Btu/h kcal/h

standby

280W/4Ω

0.3 15 15 51 13

280W/8Ω

560W/4Ω

560W/8Ω

100V

70V

idle

280W/4Ω 0.4 37 37 127 32

280W/8Ω 0.4 37 37 127 32

560W/4Ω 0.4 31 31 106 27

560W/8Ω 0.4 36 36 124 31

100V 0.4 47 47 161 41

70V 0.4 47 47 161 41

1/8 output

power

280W/4Ω 1.05 212 72 247 62

280W/8Ω1.05 208 69 235 59

560W/4Ω 1.04 207 68 232 58

560W/8Ω 1.04 210 70 240 60

100V 0.94 188 63 216 54

70V 0.94 195 70 240 60

1/3 output

power

280W/4Ω 2.2 476 100 343 86

280W/8Ω 2.1 450 77 263 66

560W/4Ω 2.2 463 91 311 78

560W/8Ω 2.3 479 105 360 91

100V 1.9 400 67 229 58

70V 2.0 429 96 32883

MODE Line Current (A)

Power

Consumption (W)

Watts

Dissipated (W)

Heat Dissipation

Btu/h kcal/h

standby

140W/4Ω

0.3 15 15 51 13

140W/8Ω

280W/4Ω

280W/8Ω

100V

70V

idle

140W/4Ω 0.5 37 37 127 32

140W/8Ω 0.5 37 37 127 32

280W/4Ω 0.4 31 31 106 27

280W/8Ω 0.5 36 36 124 31

100V 0.6 48 48 165 41

70V 0.6 48 48 165 41

1/8 output

power

140W/4Ω 1.4 130 60 206 52

140W/8Ω1.3 125 55 18948

280W/4Ω 1.3 123 53 18246

280W/8Ω 1.4 130 60 206 52

100V 1.3 120 58 197 50

70V 1.3 120 58 197 50

1/3 output

power

140W/4Ω 2.6 250 63 217 55

140W/8Ω 2.5 240 53 18346

280W/4Ω 2.5 241 54 18747

280W/8Ω 2.6 250 63 217 55

100V 2.3 220 54 18446

70V 2.3 221 55 18747

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

239

Specifications

Power Specifications (PINK NOISE, 120V/60Hz mains)

Power Specifications (PINK NOISE, 230V/50Hz mains)

1/8 power is typical of program material with occasional clipping. Refer to these figures for most applications.

1/3 power represents program material with extremely heavy clipping.

Test signal: Pink Noise, bandwidth limited from 22Hz to 22kHz

All channels driven

1W = 0.860kcal/h, 1BTU = 0.252kcal

Note that Line Voltage [V] x Line Current [A] = [VA], not equals to [W].

MODE Line Current (A)

Power

Consumption (W)

Watts

Dissipated (W)

Heat Dissipation

Btu/h kcal/h

standby

140W/4Ω

0.315155113

140W/8Ω

280W/4Ω

280W/8Ω

100V

70V

idle

140W/4Ω 0.4 37 37 127 32

140W/8Ω 0.4 37 37 127 32

280W/4Ω 0.3 31 31 106 27

280W/8Ω 0.4 36 36 124 31

100V 0.5 48 48 165 41

70V 0.5 48 48 165 41

1/8 output

power

140W/4Ω 1.2 130 60 206 52

140W/8Ω1.1 125 55 18948

280W/4Ω 1.1 123 53 18246

280W/8Ω1.2 130 60 206 52

100V 1.0 120 58 197 50

70V 1.1 120 58 197 50

1/3 output

power

140W/4Ω 2.2 250 63 217 55

140W/8Ω 2.1 240 53 18346

280W/4Ω 2.1 241 54 18747

280W/8Ω 2.2 250 63 217 55

100V 1.9 220 54 18446

70V 1.9 221 55 18747

MODE Line Current (A)

Power

Consumption (W)

Watts

Dissipated (W)

Heat Dissipation

Btu/h kcal/h

standby

140W/4Ω

0.315155113

140W/8Ω

280W/4Ω

280W/8Ω

100V

70V

idle

140W/4Ω 0.4 37 37 127 32

140W/8Ω 0.4 37 37 127 32

280W/4Ω 0.4 31 31 106 27

280W/8Ω 0.4 36 36 124 31

100V 0.4 47 47 161 41

70V 0.4 47 47 161 41

1/8 output

power

140W/4Ω 0.73 128 58 199 50

140W/8Ω0.73 127 57 196 49

280W/4Ω 0.70 122 52 178 45

280W/8Ω0.73 128 58 199 50

100V 0.68 117 55 188 47

70V 0.68 117 55 188 47

1/3 output

power

140W/4Ω 1.2 242 55 190 48

140W/8Ω 1.1 233 46 159 40

280W/4Ω 1.1 234 47 163 41

280W/8Ω 1.2 243 56 193 49

100V 1.1 213 47 160 40

70V 1.1 215 49 167 42

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

240

(weee_eu_en_02)

(weee_eu_de_02)

(weee_eu_fr_02)

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic

products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accor-

dance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative

effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste

disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier fo

r further information.

Information on Disposal in other Countries outside the European Union:

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities

or dealer and ask for the correct method of disposal.

Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte

Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten

benutzte elektrische Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden.

In Übereinstimmung mit Ihren nationalen Bestimmungen bringen Sie alte Geräte bitte zur fachgerechten Entsorgung,

Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen.

Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen, und verhindern

mögliche negative Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachge-

rechte Müllentsorgung auftreten könnten.

Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte kontaktieren Sie bitte Ihre örtliche

Sta

dt- oder Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.

Information für geschäftliche Anwender in der Europäischen Union:

Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informa-

tionen.

Entsorgungsinformation für Länder außerhalb der Europäischen Union:

Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktie-

ren Sie bitte Ihre örtlichen Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode.

Informations concernant la collecte et le traitement des déchets d’équipements électriques et électroniques

Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou électroni-

ques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.

Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniq-

ues, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale.

En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la

sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pour-

raient advenir lors d'un traitement inapproprié des déchets.

Pour plus d'inf

mations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniq-

ues, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez

acheté les produits.

Pour les professionnels dans l'Union européenne :

Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques, veuillez contacter votre

vendeur ou fournisseur pour plus d'informations.

Informations sur la mise au rebut dans d'autres pays en dehors de l'Union européenne :

Ce symbole est seulement valable dans l'Union européenne. Si vous souhaitez vous débarrasser de déchets d’équip

ments électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander la métho-

de de traitement appropriée.

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

241

(weee_eu_es_02)

(weee_eu_it_02)

(lithium disposal)

Información para usuarios sobre la recogida y eliminación de los equipos antiguos

Este símbolo en los productos, embalajes y documentos anexos significa que los productos eléctricos y electrónicos

no deben mezclarse con los desperdicios domésticos normales.

Para el tratamiento, recuperación y reciclaje apropiados de los productos antiguos, llévelos a puntos de reciclaje

correspondientes, de acuerdo con la legislación nacional.

Al deshacerse de estos productos de forma correcta, ayudará a ahorrar recursos valiosos y a impedir los posibles

efectos desfavorables en la salud humana y en el entorno que de otro modo se producirían si se trataran los desperdi-

cios de modo inapropiado.

Para obtener más información acerca de la recogida y el reciclaje de los productos antiguos, póngase en contacto con

las autoridades locales, con el servicio de eliminación de basuras o con el punto de venta donde adquirió los artículos.

Para los usuarios empresariales de la Unión Europea:

Si desea desechar equipos eléctricos y electrónicos, póngase en contacto con su vendedor o proveedor para obtener

más información.

Información sobre la eliminación en otros países fuera de la Unión Europea:

Este símbolo solo es válido en la Unión Europea. Si desea desechar estos artículos, póngase en contacto con las

toridades locales o con el vendedor y pregúnteles el método correcto.

Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura

Questi simboli sui prodotti, sull'imballaggio e/o sui documenti che li accompagnano, indicano che i prodotti elettrici ed

elettronici non devono essere mischiati con i rifiuti generici.

Per il trattamento, il recupero e il riciclaggio appropriato di vecchi prodotti, si prega di portarli ai punti di raccolta desi-

gnati, in accordo con la legislazione locale.

Smaltendo correttamente questi prodotti si potranno recuperare risorse preziose, oltre a prevenire potenziali effetti

negativi sulla salute e l'ambiente che potrebbero sorgere a causa del trattamento improprio dei rifiuti.

Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, si prega di contattare l’amministrazione comu-

nale locale, il servizio di smaltimento dei rifiuti o il punto vendita dove sono stati acquistati gli articoli.

Per utenti imprenditori dell'Unione europea:

Se si desidera scartare attrezzatura elettrica ed elettronica, si prega di contattare il proprio rivenditore o il proprio forni-

tore per ulteriori informazioni.

Informazioni sullo smaltimento negli altri Paesi al di fuori dell'Unione europea:

Questi simboli sono validi solamente nell'Unione Europea; se si desidera scartare questi articoli, si prega di contattare

le autorità locali o il rivenditore e richiedere informazioni sulla corretta modalità di smaltimento.

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-up.

• This apparatus contains a lithium battery for memory back-up.

• Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur of

gelieve dan contact op te nemen met de vertegenwoordiging van Yamaha in uw land.

• For the removal of the battery at the moment of the disposal at the end of life please consult your retailer or Yamaha representative

office in your country.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small chemical waste.

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

242

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

243

ADDRESS LIST

Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan

(For European Countries) Importer: Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Toronto, Ontario,

M1S 3R1, Canada

Tel: +1-416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620,

U.S.A.

Tel: +1-714-522-9011

MEXICO

Yamaha de México, S.A. de C.V.

Av. Insurgentes Sur 1647 Piso 9, Col. San José

Insurgentes, Delegación Benito Juárez, México,

D.F., C.P. 03900, México

Tel: +52-55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B – Vila

Olímpia – CEP 04551-010 – São Paulo/SP, Brazil

Tel: +55-11-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.,

Sucursal Argentina

Olga Cossettini 1553, Piso 4 Norte,

Madero Este-C1107CEK,

Buenos Aires, Argentina

Tel: +54-11-4119-7000

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Edif. Torre Banco General, Piso 7, Urbanización

Marbella, Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, República de Panamá

Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND

Yamaha Music Europe GmbH (UK)

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, U.K.

Tel: +44-1908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH, Branch

Switzerland in Thalwil

Seestrasse 18a, 8800 Thalwil, Switzerland

Tel: +41-44-3878080

AUSTRIA/BULGARIA/

CZECH REPUBLIC/HUNGARY/

ROMANIA/SLOVAKIA/SLOVENIA

Yamaha Music Europe GmbH

Branch Austria

Schleiergasse 20, 1100 Wien, Austria

Tel: +43-1-60203900

POLAND

Yamaha Music Europe GmbH

Sp.z o.o. Oddział w Polsce

ul. Wielicka 52, 02-657 Warszawa, Poland

Tel: +48-22-880-08-88

MALTA

Olimpus Music Ltd.

Valletta Road, Mosta MST9010, Malta

Tel: +356-2133-2093

NETHERLANDS/BELGIUM/

LUXEMBOURG

Yamaha Music Europe Branch Benelux

Clarissenhof 5b, 4133 AB Vianen, The Netherlands

Tel: +31-347-358040

FRANCE

Yamaha Music Europe

7 rue Ambroise Croizat, Zone d'activités de Pariest,

77183 Croissy-Beaubourg, France

Tel: +33-1-6461-4000

ITALY

Yamaha Music Europe GmbH, Branch Italy

Via Tinelli N.67/69 20855 Gerno di Lesmo (MB),

Italy

Tel: +39-039-9065-1

SPAIN/PORTUGAL

Yamaha Music Europe GmbH Ibérica, Sucursal

en España

Ctra. de la Coruña km. 17,200, 28231

Las Rozas de Madrid, Spain

Tel: +34-91-639-88-88

GREECE

Philippos Nakas S.A. The Music House

19th klm. Leof. Lavriou 190 02 Peania – Attiki,

Greece

Tel: +30-210-6686168

SWEDEN/FINLAND/ICELAND

Yamaha Music Europe GmbH Germany filial

Scandinavia

JA Wettergrensgata 1, 400 43 Göteborg, Sweden

Tel: +46-31-89-34-00

DENMARK

Yamaha Music Denmark,

Fillial of Yamaha Music Europe GmbH, Tyskland

Generatorvej 8C, ST. TH. , 2860 Søborg, Denmark

Tel: +45-44-92-49-00

NORWAY

Yamaha Music Europe GmbH Germany -

Norwegian Branch

Grini Næringspark 1, 1332 Østerås, Norway

Tel: +47-6716-7800

CYPRUS

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

RUSSIA

Yamaha Music (Russia) LLC.

Room 37, entrance 7, bld. 7, Kievskaya street,

Moscow, 121059, Russia

Tel: +7-495-626-5005

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yam ah a M u s i c Gu l f FZ E

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

TURKEY

Yamaha Music Europe GmbH

Merkezi Almanya Türkiye İstanbul Şubesi

Maslak Meydan Sodak, Spring Giz Plaza Bagimsiz

Böl. No:3, Sariyer Istanbul, Turkey

Tel: +90-212-999-8010

OTHER COUNTRIES

Yam ah a M u s i c Gu l f FZ E

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: +86-400-051-7700

INDIA

Yamaha Music India Private Limited

P-401, JMD Megapolis, Sector-48, Sohna Road,

Gurgaon-122018, Haryana, India

Tel: +91-124-485-3300

INDONESIA

PT. Yamaha Musik Indonesia (Distributor)

Yamaha Music Center Bldg. Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: +62-21-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, Dongsung Bldg. 21, Teheran-ro 87-gil,

Gangnam-gu, Seoul, 06169, Korea

Tel: +82-2-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn. Bhd.

No.8, Jalan Perbandaran, Kelana Jaya, 47301

Petaling Jaya, Selangor, Malaysia

Tel: +60-3-78030900

SINGAPORE

Yamaha Music (Asia) Private Limited

Block 202 Hougang Street 21, #02-00,

Singapore 530202, Singapore

Tel: +65-6740-9200

TAIWAN

Yamaha Music & Electronics Taiwan Co.,Ltd.

2F., No.1, Yuandong Rd., Banqiao Dist.,

New Taipei City 22063, Taiwan (R.O.C.)

Tel: +886-2-7741-8888

THAILAND

Siam Music Yamaha Co., Ltd.

3, 4, 15, 16th Fl., Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: +66-2215-2622

VIETNAM

Yamaha Music Vietnam Company Limited

15th Floor, Nam A Bank Tower, 201-203 Cach

Mang Thang Tam St., Ward 4, Dist.3,

Ho Chi Minh City, Vietnam

Tel: +84-8-3818-1122

OTHER ASIAN COUNTRIES

http://asia.yamaha.com/

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 80 Market Street, South Melbourne,

VIC 3205, Australia

Tel: +61-3-9693-5111

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

http://asia.yamaha.com/

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

PA5 0

Yamaha Pro Audio global website

http://www.yamaha.com/proaudio/

Yamaha Downloads

http://download.yamaha.com/

ZZ42580

Manual Development Group

Published 12/2017 POES-F0

Yamaha XMV4140 de handleiding

Merk: Yamaha

Model: XMV4140

Categorie: Aanvullende muziekapparatuur

Type: de handleiding

Deze handleiding is ook geschikt voor

Download PDF

rapport

in andere talen

English: Yamaha XMV4140 Owner's manual
italiano: Yamaha XMV4140 Manuale del proprietario
русский: Yamaha XMV4140 Инструкция по применению
français: Yamaha XMV4140 Le manuel du propriétaire
español: Yamaha XMV4140 El manual del propietario
Deutsch: Yamaha XMV4140 Bedienungsanleitung
português: Yamaha XMV4140 Manual do proprietário
dansk: Yamaha XMV4140 Brugervejledning
suomi: Yamaha XMV4140 Omistajan opas
čeština: Yamaha XMV4140 Návod k obsluze
svenska: Yamaha XMV4140 Bruksanvisning
Türkçe: Yamaha XMV4140 El kitabı
polski: Yamaha XMV4140 Instrukcja obsługi
română: Yamaha XMV4140 Manualul proprietarului

Yamaha XMV4140 de handleiding

Deze handleiding is ook geschikt voor

Yamaha XMV4140 de handleiding

in andere talen

Gerelateerde artikelen

Andere documenten