Yamaha DC3E3PRO de handleiding

Type
de handleiding
Copyright © 2011 by Yamaha CorporationEnglish
YD274C0
(Disklavier E3 / Disklavier Control Unit DKC-850)
Update Manual
Table of Contents
Updating the Disklavier.............................................................................2
Downloading the Update Program............................................................................ 2
Updating the Disklavier............................................................................................. 4
2English
Updating the Disklavier
You can download the update program in one of two ways.
Downloading the Update Program Directly from
the Internet
Press [INTERNET] on the remote control.
The Internet menu screen appears.
Select “Update” with the cursor buttons ([ ] [ ] [ ]
[ ]), then press [ENTER].
The update screen appears if there is any update available for your
instrument. If you currently have the latest version, you will not see
this screen.
You can scroll up or down using the cursor buttons ([ ] [ ]).
Downloading the Update Program
1
2
*D-Radio
*Update
*MyAccount
=Internet=
(1/1)
Continued on next page
Updating the Disklavier
English 3
Following the instructions on the screen, select the option
with the cursor buttons ([ ] [ ] [ ] [ ]), then press
[ENTER].
The download process of the update program starts.
After the download process is completed, shut down the
Disklavier by pressing [ON/OFF] on the control unit.
The update program is now downloaded and ready to be installed.
Update the firmware following the procedures in “Updating the
Disklavier” on page 4.
Downloading the Update Program Using a PC and
USB Flash Memory
Note:
The USB flash memory that you use
must have a MINIMUM of 20.0 MB
of space to copy the update program.
Prepare the personal computer and USB flash memory.
Download the update program from Yamaha website.
Note:
Copy the update program to the root
directory of the USB flash memory.
Copy the update program you have downloaded to the
USB flash memory.
If you have an earlier version of the
update program on the USB flash
memory you will be using for this
update, make sure to delete it before
updating your Disklavier. Having
more than one update program on the
USB flash memory may cause your
Disklavier to malfunction.
3
------------------------
*Update Fir
=Update=
*Cancel

4
1
2
3
Continued on next page
Updating the Disklavier
English 4
Insert the USB flash memory including the update program
into the USB port of the control unit.
The update program is ready to be installed.
Update the firmware following the procedures in “Updating the
Disklavier” on page 4.
Note:
Depending on the version or
specification of the Disklavier, the
actual indications for the version and
module names may differ from ones
depicted here.
Update the Disklavier firmware using the update program you downloaded.
While holding [PLAY/PAUSE] on the control unit, press
[ON/OFF].
The current version information of each module appears one after
the other.
Make sure that the update program is prepared, then press
[ENTER] on the control unit.
The starting screen appears.
Press [ENTER] on the control unit again.
After a while, the update confirmation message of each module
appears.
4
USB flash memory
USB port
Updating the Disklavier
1
Hold
+
CTRL system v2.20
(ENT)*UPDATE
2
3
v2.20
(PLAY,STOP)MC -SURE?
v3.00
Continued on next page
Updating the Disklavier
English 5
Important:
DO NOT turn off this unit during
update.
Press [PLAY/PAUSE] to start the update.
Important:
Be sure to update all the modules.
The update process of the first module takes approximately 3
minutes.
When the update of the first module completes, the following
confirmation message appears.
Confirmation message of the second module
Press [PLAY/PAUSE] to start the update of the second module.
The update process of the second module takes approximately 3
minutes.
A total of four modules needs to be updated. Repeat this step to
complete the update.
Confirmation message of the third module
The update process of the third module takes approximately 2
minutes.
Confirmation message of the fourth module
The update process of the fourth module takes approximately 2
minutes.
The closing screen appears when the update for all modules
completes.
Restart the Disklavier.
4
MC v2.20
DO NOT REMOVE DISK!
v3.00
v2.10
(PLAY,STOP)CTRL-SURE?
v3.00
v2.01
(PLAY,STOP)APE -SURE?
v3.00
v2.10
(PLAY,STOP)CSP -SURE?
v2.20
5
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Yamaha DC3E3PRO de handleiding

Type
de handleiding