Yamaha DVD-S795 de handleiding

Merk: Yamaha

Model: DVD-S795

Categorie: Dvd spelers

Type: de handleiding

DVD/Video CD/CD Player

DVD-S795

Operating Instructions

Before attempting to connect, operate or adjust this product,

please read this Operating Instructions manual completely

and save this manual for future reference.

VQT8007-1

Safety information

Note:

This player can be used only where the power supply

is AC 120 V, 60 Hz. It cannot be used elsewhere.

CAUTION:

DVD/VIDEO CD/CD PLAYER IS A CLASS I LASER

PRODUCT. HOWEVER THIS DVD/VIDEO CD/CD

PLAYER USES A VISIBLE LASER BEAM WHICH

COULD CAUSE HAZARDOUS RADIATION EXPO-

SURE IF DIRECTED. BE SURE TO OPERATE THE

DVD/VIDEO CD/CD PLAYER CORRECTLY AS IN-

STRUCTED.

WHEN THIS DVD/VIDEO CD/CD PLAYER IS

PLUGGED TO THE WALL OUTLET, DO NOT

PLACE YOUR EYES CLOSE TO THE OPENING

OF THE DISC TRAY AND OTHER OPENINGS TO

LOOK INTO THE INSIDE OF THIS PLAYER.

USE OF CONTROLS OR ADJUSTMENTS OR PER-

FORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR

YOURSELF. REFER SERVICING TO QUALIFIED

PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS PLAYER TO

RAIN OR MOISTURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, AND ANNOYING INTERFERENCE, USE

THE SUPPLIED ACCESSORIES ONLY.

The lightning flash with arrowhead symbol, within

an equilateral triangle, is intended to alert the user

to the presence of uninsulated “dangerous volt-

age” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral trian-

gle is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the ap-

pliance.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PER-

SONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION -LASER RADIATION WHEN OPEN.

DO NOT STARE INTO BEAM.

ATTENTION-RAYONNEMENT LASER EN CAS D'OUVERTURE.

NE PAS REGARDER DANS LE FAISCEAU.

VORSICHT -LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET.

NICHT IN DEN STRAHL BLICKEN.

ADVARSEL -LASERSTRÅLING VED ÅBNING.

SE IKKE IND I STRÅLEN.

ADVARSEL -LASERSTRÅLING NÅR DEKSEL ÅPNES.

STIRR IKKE INN I STRÅLEN.

VARNING -LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD.

STIRRA EJ IN I STRÅLEN.

VARO! -AVATTAESSA OLET ALTTIINA LASERSÄTEILYLLE.

ÄLÄ TUIJOTA SÄTEESEEN.

(Inside of player)

This player is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this player itself is turned off. This state is

called the standby mode.

In this state, this player is designed to consume a

very small quantity of power.

FOR CANADIAN CUSTOMERS

TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT AND FULLY

INSERT.

THIS CLASS B DIGITAL APPARATUS COMPLIES

WITH CANADIAN ICES-003.

Getting Started

FCC INFORMATION (for U.S.A)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the in-

structions contained in this manual, meets FCC require-

ments. Modifications not expressly approved by Yamaha

may void your authority, granted by the FCC, to use the

product.

IMPORTANT: When connecting this product to accesso-

ries and/or another product use only high quality shielded ca-

bles. Cable/s supplied with this product MUST be used. Fol-

low all installation instructions. Failure to follow instructions

could void your FCC authorization to use this product in the

USA.

NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these require-

ments provides a reasonable level of assurance that your

use of this product in a residential enviroment will not result

in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the opera-

tion of other electronic devices.

Compliance with FCC regulations does not guarantee that in-

terference will not occur in all installations. If this product is

found to be the source of interference, which can be deter-

mined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affect-

ed by the interference.

Utilize power outlets that are on different branch (circuit

breaker of fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory re-

sults, please contact the local retailer authorized to distribute

this type of product. If you can not locate the appropriate re-

tailer, please contact Yamaha Electronics Corp., U.S.A. 6600

Orangethorpe Ave, Buena Park, CA 90620

The above statement apply ONLY to those products distribut-

ed by Yamaha Corporation of America or its subsidiaries.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the

most out of your equipment by playing it at a safe lev-

el. One that lets the sound come through loud and

clear without annoying blaring or distortion—and,

most importantly, without affecting your sensitive

hearing. Since hearing damage from loud sounds is

often undetectable until it is too late,

YAMAHA and the Electronic Industries

Association’s Consumer Electronics

Group recommend you to avoid

prolonged exposure from excessive

volume levels.

Precautions

Please read these precautions before operating this player.

È AC cord

To avoid any malfunctions of the player, and to protect against

electric shock, fire or personal injury, please observe the fol-

lowing:

ÁHold the plug firmly when connecting or disconnecting

the AC cord to this player.

ÁDo not connect or disconnect the AC cord when your

hands are wet.

ÁKeep the AC cord away from heating appliances.

ÁNever put any heavy object on the AC cord.

ÁDo not attempt to repair or reconstruct the AC cord in

any way.

ÁRemove dust, dirt, etc. on the plug at regular intervals.

ÁIf the player has been dropped or otherwise damaged,

set the player to the standby mode and disconnect the

AC cord.

ÁIf smoke, malodors or noises are emitted from the play-

er, set the player to the standby mode and disconnect

the AC cord.

È Placement

Avoid placing the player in areas of:

Ádirect sunlight or heating radiators, or closed automobiles

Áhigh temperature [over 95uF (35uC)] or high humidity (over

90%)

Áexcessive dust

Ávibration, impact or where the surface is tilted as the internal

parts may be seriously damaged.

ÁPlace the player in a horizontal position, and do not place

anything heavy on it.

ÁDo not place the player on amplifiers or other equipment

which may become hot.

È Non-use periods

When the player is not being used, set the player to the stand-

by mode.

When left unused for a long period of time, the player should

be unplugged from the household AC outlet.

È Do not place objects inside the player

ÁTouching internal parts of this player is dangerous, and may

cause serious damage to the player. Do not attempt to disas-

semble the player.

ÁDo not put any foreign object on the disc tray.

È Keep away from water and magnets.

ÁKeep the player away from flower vases, tubs, sinks, etc. If

liquids are spilled into the player, serious damage could

occur.

ÁKeep magnetic objects such as speakers, at a distance from

the player.

È Condensation

Moisture may form on the lens in the following conditions:

Áimmediately after a heater has been turned on.

Áin a steamy or very humid room.

Áwhen the player is moved from a cold environment to a warm

one.

If moisture forms inside this player, it may not operate proper-

ly. In this case, turn on the power and wait about one hour for

the moisture to evaporate.

È When watching a TV broadcast

Depending on the reception condition of the TV, interference

may appear on the TV screen while you are watching a TV

broadcast and the player is left on. This is not a malfunction of

the player or the TV. To watch a TV broadcast, set the player

to the standby mode.

Dear Customers

May we take this opportunity to thank you for purchasing this

YAMAHA DVD/Video CD/CD player.

We strongly recommend that you carefully study the Operating

Instructions before attempting to operate the player and that

you note the listed precautions.

Accessories

Please check and identify the

supplied accessories.

Remote control

unit . . . . . . . . . . . . . . 1

Batteries . . . . . . . . . 2

for remote control unit

[size “AA”]

AC cord . . . . . . . . . . 1

Video/audio

cable . . . . . . . . . . . . 1

The model number and serial number of this player can

be found on either the back or the bottom of the player.

Please note them in the space provided below and re-

tain this booklet as a permanent record of your purchase

to aid identification in the event of theft.

MODEL NUMBER__________________________

SERIAL NUMBER__________________________

This product incorporates copyright protection technolo-

gy that is protected by method claims of certain U.S. pat-

ents and other intellectual property rights owned by

Macrovision Corporation and other rights owners. Use of

this copyright protection technology must be authorized

by Macrovision Corporation, and is intended for home

and other limited viewing uses only unless otherwise au-

thorized by Macrovision Corporation. Reverse engineer-

ing or disassembly is prohibited.

Getting StartedBasic OperationOperation Using

On-Screen Menu Icons

Advanced OperationInitial SettingsFor Your Reference

Table of contents

Getting Started:

Safety information . . . . . . . . . . . . . . . . . . . . . 02

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 03

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 04

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06

Definition of terms . . . . . . . . . . . . . . . . . . . . . 7

Control reference guide . . . . . . . . . . . . . . . . . 08

ÁMain unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 008

ÁRemote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 008

Front panel FL display . . . . . . . . . . . . . . . . . . 09

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ÁConnecting to an AV amplifier containing Dolby Digital

or dts (digital theater systems) decoder . . . . . . . . . . . . . 010

ÁConnecting to an AV amplifier which does not contain

Dolby Digital or dts (digital theater systems)

decoder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 012

Remote control unit preparation . . . . . . . . . . 13

ÁBattery installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 013

ÁRemote control operation range . . . . . . . . . . . . . . . . . . . 013

Connecting headphones . . . . . . . . . . . . . . . . 13

Basic Operation:

Basic play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

ÁBefore enjoying DVD/Video CD/CD . . . . . . . . . . . . . . . . 014

ÁBasic play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 014

ÁStopping play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 015

Skipping ahead or back . . . . . . . . . . . . . . . . . 16

Still picture (Pause) . . . . . . . . . . . . . . . . . . . . 16

Rapid advance (Rapid reverse) . . . . . . . . . . . 17

Frame advance (Frame reverse)

[DVD/Video CD] . . . . . . . . . . . . . . . . . . . . . . . . 17

Slow-motion play

[DVD/Video CD] . . . . . . . . . . . 17

Enjoying Video CDs with playback control

without using menus

[Video CD] . . . . . . . . . 17

Operation Using On-Screen Menu Icons:

General information about On-Screen Menu

Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

ÁCommon procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . 018

Detailed descriptions of each On-Screen

Menu Icon. . . . . . . . . . . . . . . . . . . . . . . . . . . 19

ÁScreen for disc information (For DVD) . . . . . . . . . . . . . . 019

ÁScreen for disc information (For Video CD/CD) . . . . . . . 020

ÁScreen for player information . . . . . . . . . . . . . . . . . . . . . 021

ÁShuttle screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 022

Advanced Operation:

Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

ÁRepeat viewing (listening) . . . . . . . . . . . . . . . . . . . . . . . 023

ÁRepeating sections between two specific points

(A-B repeat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 024

Program play [Video CD/CD] . . . . . . . . . . . . . . . . . . 25

Random play

[Video CD/CD] . . . . . . . . . . . . . . . 26

Storing markers in memory to be viewed

(listened to) again . . . . . . . . . . . . . . . . . . . . 26

ÁStoring a marker in the memory . . . . . . . . . . . . . . . . . . . 026

ÁRecalling/clearing a marker . . . . . . . . . . . . . . . . . . . . . . 027

Changing audio soundtrack language

[DVD] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Switching vocals ON or OFF for Karaoke

discs

[DVD/Video CD] . . . . . . . . . . . . . . . . . . . 27

Changing subtitle language

[DVD] . . . . . . . . . 28

Viewing from another angle

[DVD] . . . . . . . . . 29

Using a title menu

[DVD] . . . . . . . . . . . . . . . . . 29

Using a DVD menu

[DVD]. . . . . . . . . . . . . . . . . 29

Initial Settings:

Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . 30

ÁCommon procedures of initial settings . . . . . . . . . . . . . . 030

ÁSelecting disc languages [DVD] . . . . . . . . . . . . . . . . . . . 031

ÁSelecting rating level [DVD] . . . . . . . . . . . . . . . . . . . . . . 032

ÁSelecting language of On-Screen Display menu . . . . . . 033

ÁSelecting the display format of the On-Screen

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 034

ÁSelecting the FL display brightness . . . . . . . . . . . . . . . . 035

ÁSelecting TV screen type . . . . . . . . . . . . . . . . . . . . . . . . 036

ÁConcerning images which appear on the TV screen

(aspect ratios of the screen) . . . . . . . . . . . . . . . . . . . . . . 037

ÁSelecting digital output . . . . . . . . . . . . . . . . . . . . . . . . . . 038

ÁSpeaker settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

ÁOther settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 042

Language code list . . . . . . . . . . . . . . . . . . . . . 44

For Your Reference:

Disc handling and maintenance . . . . . . . . . . 45

ÁMaintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 045

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 46

ÁSelf-diagnosis display function . . . . . . . . . . . . . . . . . . . . 047

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 48

Features

È High picture quality

Á10 bit video D/A converter

With its 10 bit capability, this D/A converter reproduces fine

images faithfully.

ÁComponent video output

When used with a compatible monitor, a video connection via

the component video output jacks of your new DVD/Video CD/

CD player is capable of the most precise color reproduction in

a video signal.

ÁAn array of picture quality modes yielded by digital

processing

Signal deterioration is kept to the minimum by processing the

data as digital data.

This feature can be used as the picture quality setting individ-

ually tailored for DVD playback.

–Cinema Image (See page 21.)

Using the On-Screen Menu Icon enables the cinema mode,

which is best for the playback of movie programs, to be se-

lected.

In addition, the picture quality best suited to the type of soft-

ware programs concerned can be selected. In all, four pic-

ture quality modes are provided: normal, soft, fine and

cinema.

–User selection (See page 21.)

Using the On-Screen Menu Icon, the contrast, color hue,

equalizer and brightness can be adjusted to suit your own

preference.

–Monitor selector (See page 36.)

Once the type of TV used [Standard (Direct View TV), CRT

Projector, LCD Projector, Projection TV] has been selected

when the initial setting operations are performed, the opti-

mum picture quality for the type of TV concerned will be

automatically selected.

È High sound quality

Á96 kHz/24 bit audio D/A converter

This player enables 96 kHz/24 bit linear PCM signals, which

constitute the highest specifications in the DVD standards, to

be reproduced faithfully. To support 96 kHz sampling/24 bit

sound, the shaping noise of this multi-level digital sigma type

of D/A converter is kept flat up to 44 kHz, thus preventing the

important audio signals from being affected in any way. In

terms of the bottom line, the sound in all of its various modes

is reproduced faithfully.

ÁDolby Digital 5.1ch surround decoder

(See pages 21 and 40.)

The Dolby Digital 5.1ch surround decoder incorporated in

this player comes with speaker mode settings which support

the low-range reproduction capability of the speakers, speak-

er level settings, delay time settings, audio dynamic range

suppression, Cinema Dialogue function to make it easier to

hear movie dialogues, and other features.

Ádts (digital theater systems) digital output (See page 10.)

By connecting an amplifier incorporating a dts decoder, you

can enjoy high quality digital surround from dts discs.

È On-Screen Menu Icons (See page 18.)

By simply pressing the ON SCREEN button on the remote

control, information on the DVD/Video CD/CD player and disc

can be displayed on the TV screen for easy identification. The

player’s operations and settings can be easily accessed by

operating the cursor buttons on the remote control while moni-

toring the TV screen. The color and position of the On-Screen

Menu Icons can be changed.

È Versatile DVD features

ÁMulti-audio function (See page 27.)

The audio soundtrack can be heard in up to 8 languages.

(The number of audio sound languages depends on the soft-

ware.)

ÁMulti-subtitle function (See page 28.)

Subtitles may be displayed in one of a maximum of 32 lan-

guages. (The number of the subtitle languages depends on

the software.)

ÁMulti-angle function (See page 29.)

This function allows you to choose the viewing angle of

scenes which were shot from a number of different angles.

(Limited to DVD recorded with multiple camera angles.)

ÁParental lock function (See page 32.)

This function can prevent playback of DVD software unsuita-

ble for some audiences (especially for children).

È Marker function (See page 26.)

This player can store a maximum of 5 positions in memory, for

convenient access, as desired.

È Disc formats supported by this player

The player can play back discs bearing any of the following

marks:

È Discs which cannot be played with this

player

ÁDVD with Region No. other than “1” or “ALL”

ÁDisc of PAL system ÁCD-G

ÁDVD-ROM ÁCD-RW

ÁDVD-R/DVD-RAM ÁDVDoRW

ÁCD-ROM ÁCVD

ÁVSD ÁSVCD

ÁCDV ÁDivx Video Disc

etc.

ÁDo not try to play Photo CD or CD-R.

(Otherwise, data on the disc may be damaged.)

È Region Management Information

This player is designed and manufactured to respond to the

Region Management Information that is recorded on a DVD

disc. The Region number of this player is “1”. If the Region

number described on the DVD disc does not correspond to the

Region number of this player, this player cannot play this disc.

This player will play DVD discs made for “ALL” Regions. This

player will play DVD discs marked with the following symbols:

DVD

[3w (8 cm) disc/

5w (12 cm) disc]

Video CD

[3w (8 cm) disc/

5w (12 cm) disc]

[3w (8 cm) disc/

5w (12 cm) disc]

ALL

Getting Started

Angle

Recorded onto some DVD discs are scenes which have been

simultaneously shot from a number of different angles (the

same scene is shot from the front, from the left side, from the

right side, etc.). With such discs, the ANGLE button can be

used to view the scene from different angles.

Chapter number

These numbers are recorded on DVD discs. A title is subdivid-

ed into many sections, each of which is numbered, and specif-

ic parts of video presentations can be searched quickly using

these numbers.

Digital audio output connector (Optical)

The digital audio output connector (optical) converts electrical

signals into optical signals and transfers them to the amplifier.

Consequently, it has a number of features including its immu-

nity from electrical interference from external sources and its

ability to prevent the generation of noise and its minimal effect

on the external environment.

DVD

This refers to a high-density optical disc on which high-quality

pictures and sound have been recorded by means of digital

signals. Incorporating a new video compression technology

(MPEG 2) and high-density recording technology, DVD en-

ables esthetically pleasing full-motion video to be recorded

over long periods of time (for instance, a whole movie can be

recorded).

DVD has a structure consisting of two 0.6 mm thin discs which

are adhered to each other. Since the thinner the disc, the high-

er the density at which the information can be recorded, a DVD

disc has a greater capacity than a single 1.2 mm thick disc.

Since the two thin discs are adhered to each other, there is the

potential to achieve double-sided play sometime in the future

for even longer duration of play.

Field

Half of the video information (video signal) in a frame is called

a field. With conventional TV systems, a signal frame (a single

screen) consists of two fields.

Field still

Only one field (half of the video information) is displayed on the

TV screen, so the apparent resolution is low. However, there is

no blurring on the screen.

Frame

Individual images in a video or on the TV are called frames.

Frame still

The two fields are displayed, alternately, on the TV screen, so

the image is blurry. However, the image quality is better than

field images.

Playback control

This is recorded on a Video CD (version 2.0). The scenes or

information to be viewed (or listened to) can be selected inter-

actively with the TV monitor by looking at the menu shown on

the TV monitor.

Subtitles

This is the appearance of the dialogue at the bottom of the

screen which are prerecorded on some DVD discs.

Title number

These numbers are recorded on DVD discs. When a disc con-

tains two or more movies, these movies are numbered as title

1, title 2, etc.

Track number

These numbers are assigned to the tracks which are recorded

on Video CDs and CDs. They enable specific tracks to be lo-

cated quickly.

Video CD

This contains recordings of pictures and sound whose quality

is on a par with that of videotape. This player also supports

Video CDs with playback control (version 2.0).

Definition of terms

Remote control unit

Page

e POWER button (*/I) . . . . . . . . . . . . . . . . . . . . . . . . . . 14

f STOP button (@) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

g SKIP buttons (H, I). . . . . . . . . . . . . . . . . . . . 15, 16

h TITLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 29

i Cursor buttons (A, B, C, D)/SELECT button . . . . . 15

j ON SCREEN button . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

k AUDIO button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

l SUBTITLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

m MARKER button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

n PLAY MODE button . . . . . . . . . . . . . . . . . . . . . . . . 25, 26

o REPEAT button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

p CLEAR button. . . . . . . . . . . . . . . . . . . . . . . 18, 21, 25, 27

q A-B button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

r SET UP button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

s OPEN/CLOSE button . . . . . . . . . . . . . . . . . . . . . . . . . . 14

t STILL/PAUSE button (g). . . . . . . . . . . . . . . . . . . . . . . 16

u PLAY button (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

v SLOW/SEARCH buttons (F, G) . . . . . . . . . . . . . . 17

w MENU button . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 17, 29

x RETURN button . . . . . . . . . . . . . . . . . . . . . . . . 15, 18, 30

y ANGLE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

z Numeric buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ÁTo select a 2-digit number

Example: To select track 23

Press “X10”, “2” and then “3”.

Control reference guide

Main unit

Page

e STANDBY/ON button . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Press to switch the player from standby mode to ON or vice

versa. In standby mode, the player is still consuming a

small amount of power.

f Disc tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

g OPEN/CLOSE button (E) . . . . . . . . . . . . . . . . . . . . . . . 14

h PLAY button (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

i PAUSE button (g) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Page

j STOP button (@) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

k Headphones jack (PHONES) . . . . . . . . . . . . . . . . . . . . 13

l Phones level control (LEVEL) . . . . . . . . . . . . . . . . . . . 13

m Remote control signal sensor. . . . . . . . . . . . . . . . . . . 13

n FL Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

o SKIP buttons (H, I). . . . . . . . . . . . . . . . . . . . 15, 16

p SEARCH buttons (F, G) . . . . . . . . . . . . . . . . . . . . 17

NATURAL SOUND DVD PLAYER

STANDBY/ON

PHONES LEVEL

010

f OPEN/CLOSE

DVD / VIDEO CD / CD

SKIP

;

D I G I T A L

1fghij

ponmlk

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

Getting Started

Front panel FL display

e Rotates during play.

Rotates fast clockwise or counterclockwise

during rapid advance (reverse). (See page 17.)

Rotates slowly clockwise or counterclockwise

during slow-motion play.

[DVD/Video CD] (See page 17.)

Illuminates in the stop mode.

f Illuminates during playback.

Flashes when the RESUME function is ON.

(See page 15.)

g Illuminates during repeat play. (See pages 23 and 24.)

h Illuminates in the still picture (pause) mode.

(See page 16.)

i Indicates the title/chapter number. [DVD]

Indicates the track number. [Video CD/CD]

j Indicates the elapsed playing time from the start of the

title/track during play.

k Indicates the audio channel information recorded in the

disc being played back (e.g. 2ch or 5.1ch).

l Illuminates when a DVD is loaded.

m Illuminates when it is possible to switch the angle.

[DVD] (See page 29.)

n Illuminates during program play. [Video CD/CD]

(See page 25.)

o Illuminates when Linear PCM of 96 kHz sampling is be-

ing played.

p Illuminates when Linear PCM of 24 bit is being played.

q Illuminates when the disc tray is open.

r Illuminates when the disc tray is being closed (re-

tracted).

s Illuminates during play of a DVD.

t Illuminates during play of an interactive DVD.

u Illuminates during play of a Karaoke DVD.

v Illuminates during play of an interactive Karaoke DVD.

w Illuminates during play of a Video CD.

x Illuminates during play of a Video CD with playback

control.

y Illuminates during play of a CD.

z Illuminates when the track number is selected to be

stored in the memory (program play). [Video CD/CD]

(See page 25.)

{ Illuminates when playback is impossible.

ÁDVD for which playback is prohibited by the initial settings

“2 Ratings”. (See page 32.)

ÁDVD with Region No. other than “1” or “ALL”

Á(See page 6.)

ÁDisc of PAL system

| Illuminates when no disc is loaded.

An interactive DVD is DVD software which includes multi-

ple angles, multiple plot endings, etc.

Surround (L)

Front (L)

Center

Surround (R)

Subwoofer

Front (R)

DVD

PROG.

ANGLE

96kHz 24bit

1 3 5 642

89 o0 p

{

DVD

PROG.

Connection

ÁEnsure that this player and other equipment to be connected are set to the standby mode or off, and disconnect the AC cord, before commencing

connection.

ÁDo not block ventilation holes of any of the equipment and arrange them so that air can circulate freely.

ÁRead through the instructions before connecting other equipment.

ÁEnsure that you observe the color coding when connecting audio and video cables.

ÁSelect the appropriate screen type at the initial setting “6 TV Aspect” according to your TV set [4:3/16:9 and Standard (Direct View TV)/CRT Projector/

LCD Projector/Projection TV]. (See page 36.)

Notes:

ÁIf the DVD/Video CD/CD player is connected to the TV through a video cassette recorder, the picture may not be played back normally with some

DVDs.

ÁWhen playing some DVD discs, TV volume level may be lower than from some other sources, adjust the TV volume to your desired level.

ÁWhen the DVD/Video CD/CD player is connected to the TV set through the component video output connectors, the ON SCREEN informations from

the amplifier will not show on the TV screen. To show them, select the input position which is connected to the amplifier on the TV set.

Do not place the player on amplifiers or other equipment which may become hot.

Connecting to an AV amplifier containing Dolby Digital or dts (digital theater systems)

decoder

When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or dts bitstream is output from the player’s OPTICAL

digital audio output connector or COAXIAL digital audio output connector. When the player is connected to a Dolby Digital decoder or

dts decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable or coaxial digital audio cable (both

optional) is required when an optional Dolby Digital decoder or dts decoder is used.]

Note:

ÁWhen connecting an AV amplifier which contains dts decoder, be sure to select “Bitstream” at “3 dts” of the initial setting “7 Digital

Audio Output”. (“Off” is selected at the factory preset.) If “Off” is selected, dts bitstream is not output from the digital audio output

connector.

Video cable (optional)

Direction of

signal flow

TV set (optional)

Coaxial digital

audio cable

(optional)

Optical

digital

audio cable

(optional)

Video/audio

cable

(supplied)

S video

cable

(optional)

DVD/Video CD/CD player

AC cord (supplied)

To AC outlet

To component video input

connectors (Y, C

B, CR)

COAXIAL

DVD/LD

OPTICAL

DVD/

AUDIO SIGNAL

R L VIDEO S-VIDEO

VIDEO SIGNAL

PCM/U DIGITAL

DTS

COAXIAL

AUDIO OUT

OPTICAL

SUBWOOFER

CENTER SURROUND

6CH DISCRETE

MIXED 2CH

VIDEO

MAIN

S VIDEO

YCB CR

VIDEO OUT

COMPONENT VIDEO

AC IN

AV amplifier with

Dolby Digital/dts

decoder (optional)

Getting Started

Dust protection cap

Component video output connectors (Y, C

B, CR)

The component video output connector outputs the color dif-

ference signals (C

B, CR) and luminance signal (Y) separately in

order to achieve high fidelity in reproducing colors.

ÁThe description of the component video input connectors

may differ depending on the TV set or monitor (e.g. Y, P

B, PR/

Y, B-Y, R-Y/Y, C

B, CR and so on). Refer to the instruction

manual of your TV set for details.

S video output connector

The S video output connector separates the color (C) and lu-

minance (Y) signals before transmitting them to the TV set in

order to achieve a sharper picture.

Use the S video cable (optional) when connecting the player to

a TV set equipped with an S video input connector for the best

picture clarity possible.

Notes when connecting the optical digital audio cable

(optional)

ÁRemove the dust protection cap from the optical digital audio

output connector and connect the cable firmly so that the

configurations of both the cable and the connector match.

ÁKeep the dust protection cap and, to protect against dust, al-

ways reattach the cap when not using the connector.

Concerning the audio output from the player’s optical/

coaxial digital audio output connector

The type of audio output from the connector can be selected

by “7 Digital Audio Output” of the initial settings.

(See page 38.)

Compressed sound converted to PCM will be output.

Disc

DVD

Video

Sound

recording

format

Dolby Digital

Linear PCM

(48/96 kHz

16/20/24 bit)

dts

MPEG 1

Linear PCM

Optical/coaxial digital

audio output from

connector

Dolby Digital bitstream

(1–5.1ch) or PCM (2ch)

(48 kHz/16 bit)

\1 \2

Linear PCM (2ch)

(48 kHz sampling/16 bit

only) or no output

dts bitstream (1–5.1ch) or

no output

PCM

(44.1 kHz sampling)

Linear PCM

(44.1 kHz sampling)

Caution for the optical/coaxial digital audio output

connector:

È When connecting an amplifier (with an optical/

coaxial digital input connector) which contains

the Dolby Digital decoder or dts decorder

ÁBe sure to select “Bitstream” both at “2 Dolby Digi-

tal” and “3 dts” of the initial setting “7 Digital Audio

Output”. (See page 38.)

È When connecting an amplifier (with an optical/

coaxial digital input connector) which does not

contain the Dolby Digital decoder or dts de-

coder

ÁBe sure to select “PCM” at “2 Dolby Digital” and

“Off” at “3 dts” of the initial setting “7 Digital Audio

Output”. (See page 38.)

ÁOtherwise any attempt to play DVDs may cause

such a high level of noise that it may be harmful to

your ears and damage your speakers.

ÁVideo CDs and CDs can be played as they would

normally be played.

Note:

ÁSome dts decoders which do not support DVD-dts interface

may not work properly with the DVD/Video CD/CD player.

For your reference:

ÁDolby Digital is a digital sound compression technique devel-

oped by the Dolby Laboratories, Inc.

Supporting 5.1-channel surround sound, as well as stereo

(2-channel) sound, this technique enables a large quantity

of sound data to be efficiently recorded on a disc.

ÁLinear PCM is a signal recording format used in a CD. While

a CD is recorded in 44.1 kHz/16 bit, a DVD is recorded in

48 kHz/16 bit up to 96 kHz/24 bit.

ÁIf you have a Dolby Pro Logic Surround decoder, you will

obtain the full benefit of Pro Logic from the same DVD mov-

ies that provide full 5.1-channel Dolby Digital soundtracks, as

well as from titles with the Dolby Surround mark.

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of

Dolby Laboratories. Confidential Unpublished Works.

j 1992–1997 Dolby Laboratories, Inc. All rights re-

served.

Connection

Connecting to an AV amplifier which does not contain Dolby Digital or dts (digital theater

systems) decoder

This DVD/Video CD/CD player contains a Dolby Digital decoder. This enables the playback of DVDs recorded in Dolby Digital Sur-

round or Linear PCM without the need for an optional decoder with Dolby Digital or Linear PCM processing. When the DVD/Video CD/

CD player is connected to an AV amplifier with 5.1ch input connectors, you can enjoy theater-quality audio in your home when playing

discs recorded in Dolby Digital Surround or Linear PCM.

TV set (optional)

Video/audio

cord

(supplied)

DVD/Video CD/CD player

Audio cord

(optional)

Notes:

ÁAfter connection is made, set the “8 Speaker Setting” (such

as Yes/No and Large/Small) according to your speaker sys-

tem. (See page 40.)

ÁIf the surround speakers are set to “No” at the “8 Speaker

Setting” (see page 40), the discs recorded in Linear PCM will

be played back only in 2 channels even when the center

speaker is connected as well as the front speakers.

ÁDVDs recorded in Linear PCM/96 kHz sampling in which

“Center Speaker” is contained will also be played back only

in 2 channels.

ÁIf the player is connected to the AV amplifier as shown

above, audio recorded in dts will not be output. To enjoy dts

sound, it is necessary to connect the player as shown on

page 10.

Direction of

signal flow

Video cable

(optional)

To component video input

connectors (Y, C

B, CR)

PCM/U DIGITAL

DTS

COAXIAL

AUDIO OUT

OPTICAL

SUBWOOFER

CENTER SURROUND

6CH DISCRETE

MIXED 2CH

VIDEO

MAIN

S VIDEO

VIDEO OUT

COMPONENT VIDEO

AC IN

CENTER

SUB

WOOFER

MAIN

SURROUND

AUDIO SIGNAL

DVD/LD

VIDEO SIGNAL

S-VIDEO

6CH DISCRETE INPUT DVD/LD

AV amplifier without

Dolby Digital/dts

decoder (optional)

S video cord

(optional)

In the case of the AV amplifier without

5.1ch input connectors

In the case of the AV amplifier

with 5.1ch input connectors

Getting Started

Remote control unit preparation

Battery installation A

Insert the batteries while observing the correct (o) and (p) po-

larities as illustrated at left.

Service life of batteries

ÁThe batteries normally last for about one year although this

depends on how often, and for what operations, the remote

control unit is used.

ÁIf the remote control unit fails to work, even when it is operat-

ed near the player, replace the batteries.

ÁUse size “AA” batteries.

Remote control operation range B

Point the remote control unit from no more than about 23 feet

(7 m) from the remote control sensor and within about 60u of

the front of the player.

ÁThe operating distance may vary according to the brightness

of the room.

Notes:

ÁDo not point bright lights at the remote control sensor.

ÁDo not place objects between the remote control unit and the

remote control sensor.

ÁDo not use this remote control unit while simultaneously op-

erating the remote control unit of any other equipment.

Connecting headphones C

Connect the headphones (optional).

ÁHeadphones with a

/4w (6.3 mm) stereo plug can be con-

nected.

Adjust the volume.

Caution:

Avoid listening to sound at levels which may be harmful to your

ears.

Notes:

ÁDo not use rechargeable (Ni-Cd) batteries.

ÁDo not attempt to recharge, short-circuit, disassemble,

heat or throw the batteries into a fire.

ÁDo not drop, step on or otherwise impact the remote

control unit. This may damage the parts or lead to mal-

function.

ÁDo not mix old and new batteries.

ÁIf the remote control unit is not going to be used for a

long time, remove the batteries. Otherwise, electrolyte

may leak which may lead, not only to malfunctioning

but also, to burns if contact is made with the electro-

lyte.

ÁWipe away any electrolyte leaking inside the remote

control unit, and install new batteries.

ÁIf any electrolyte should come into contact with parts of

your body, wash it off thoroughly with water.

Remote control signal sensor

23 feet (7 m)

STANDBY/ON

PHONES LEVEL

010

f OPEN/CLOSE

DVD / VIDEO CD / CD

NATURAL SOUND DVD PLAYER

SKIP

;

D I G I T A L

30˚ 30˚

STANDBY/ON

PHONES LEVEL

010

DVD / VIDEO CD /

NATURAL SOUND DVD PLAYER

LEVEL

010

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

POWER

*/ I

STOP

TITLE

RETURN

PLAY

OPEN/CLOSE

SKIP I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

SELECT

NATURAL SOUND DVD PLAYER

STANDBY/ON

PHONES LEVEL

010

f OPEN/CLOSE

DVD / VIDEO CD / CD

SKIP

;

SKIP

;

D I G I T A L

Before enjoying DVD/Video CD/CD

The On-Screen menu language of your player has been

factory preset to English.

If you would like to change the menu language to

French or Spanish, please refer to “Selecting language

of On-Screen Display menu” on page 33.

In the explanations given below it is assumed that Eng-

lish has been selected as the menu language.

Basic play

Open

CloseReading

Preparations

ÁConfirm that the TV set or the audio equipment (if connected)

is properly connected to the player.

ÁConfirm that the power for the TV set or the audio equipment

(if connected) is turned on.

ÁConfirm that the input setting for the TV set or the audio

equipment (if connected) is properly selected.

(Example: Select “VCR 2” on the TV set if this player has

been connected to TV input connector [2].)

Basic play

Press POWER to switch on the power.

Press OPEN/CLOSE to

open the disc tray.

Place the disc on the disc tray with the label

side to be played facing upwards.

Hold the disc without touching either of its surfaces, posi-

tion it with the label side to be played facing upwards,

align it with the guides, and place it in its proper position.

e 3w (8 cm) disc

f 5w (12 cm) disc

Press PLAY.

The disc tray is automatically closed and play begins.

Basic Operation

ÁWhen the disc tray is closed by pressing OPEN/CLOSE,

press PLAY to start play.

ÁWhen a menu screen appears on the TV monitor

In case of an interactive DVD or

a Video CD with playback con-

trol, a menu screen appears on

the TV monitor. Perform step

5 to start play.

Press the cursor buttons (A, B, C, D) and

press SELECT, or press the numeric but-

tons, to select the preferred item.

ÁThe cursor buttons (A, B, C, D) are not effective for

selecting items for Video CDs.

Play of the selected item now begins.

While watching the movie program

ÁSetting to the picture quality best suited to movies

Using the On-Screen Menu Icon will select the optimum pic-

ture quality for movie programs (this setting gives a gentler

feel to videos, producing more detail in darker scenes and

helping to reduce noise).

The picture quality of your choice can be set using the On-

Screen Menu Icons. (See “Cinema Image” on page 21.)

ÁRaising the volume but only for the dialogue

The volume for the dialogue only can be raised by displaying

the On-Screen Menu Icons (for player information) and set-

ting “Cinema Dialogue” to “ON”. (See page 21.)

[This setting takes effect only for discs which are recorded

with Dolby Digital 5.1ch and with the sound contained in the

center channel.]

When the menu continues onto another screen

After step 4 on page 14, press SKIP (I).

ÁTo return to the previous menu screen

Press SKIP (H).

ÁDue to the design of some software titles, SKIP (H, I)

may not always work. For operation, refer also to the jacket

of the disc concerned.

Stopping play and returning to the menu

screen

Press TITLE, MENU or RETURN (for DVD), or RETURN (for

Video CD).

Play is suspended, and the menu screen is displayed.

ÁThe buttons may not work depending on the disc used.

What is playback control?

If a Video CD has “playback control” written on its disc or

jacket, it means that particular scenes or information can

be selected for viewing interactively with the TV monitor

using the menu screen.

(Example)

(Example of DVD)

Notes:

ÁThe disc continues to rotate while the menu is displayed

even after the player has finished playing a particular item.

When no further selections are to be played, be sure to press

STOP to clear the menu display.

ÁIf the disc is placed in upside down (and it is a single sided

disc), the FL display will indicate “NO PLAY”.

For your reference:

ÁWhen —— appears on the TV monitor while a button is be-

ing operated, it means that the corresponding operation is

prohibited by the player or the disc.

Stopping play

Press STOP during play.

RESUME function

The player records the point where STOP was pressed during

play (RESUME function). (“D” flashes on the player’s FL dis-

play when this function is activated.)

ÁPress PLAY again while “D” flashes, and play will resume

from this point.

ÁWhen the tray is opened or STOP is pressed again while “D”

flashes, the RESUME function will be cleared.

The RESUME function works only with titles for which the

elapsed playing time appears on the player’s FL display during

playback.

This feature will not be cleared when the player is set to the

standby mode and then turned back ON.

Chapter preview function (DVD only)

When PLAY is pressed while

“D” flashes, the message

shown at right is displayed.

When PLAY is pressed again while the above message is dis-

played, the first few seconds of each chapter from the begin-

ning of the title up to the point where operation was stopped

will be played. This makes it possible to review previously

viewed chapters. Normal playback will commence from the

point where operation was stopped.

Notes:

ÁCancelling the RESUME function will also clear the chapter

preview function.

ÁThe chapter preview function may not work with some DVDs.

After operation

When the player is not in use, remove the disc and press

POWER to set the player to the standby mode.

The player is automatically set to the standby mode after

30 minutes or so have elapsed in the stop mode.

(Auto power-off function)

TITLE MENU

Dogs

BirdsLovers

Castles

of the world

TITLE MENU

Birds

Dogs

Lovers

Castles

Press PLAY to Chapter Preview

Skipping ahead or back

Press SKIP (H, I) during play.

H: Reverse direction

I: Forward direction

For your reference:

ÁA chapter (DVD) or a track (Video CD/CD) is skipped each

time the button is pressed.

ÁWhen SKIP (H) is pressed once midway through a chap-

ter/track, play returns to the start of that chapter/track. When

it is pressed again, a chapter/track is skipped each time the

button is pressed.

ÁWhen SKIP (H, I) is pressed during menu play of Vid-

eo CDs with playback control, a menu screen may some-

times be recalled.

Still picture (Pause)

By the remote control unit

Press STILL/PAUSE during play.

By the main unit

Press PAUSE during play.

ÁDVD/Video CD: The player will be placed in the still picture

mode.

ÁCD: The player will be placed in the pause

mode.

ÁNormal play is resumed when PLAY is pressed.

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

SELECT

STILL/PAUSE

PLAY

SKIP I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

POWER

NATURAL SOUND DVD PLAYER

STANDBY/ON

PHONES LEVEL

010

f OPEN/CLOSE

DVD / VIDEO CD / CD

SKIP

;

SKIP

;

D I G I T A L

STOP

Basic Operation

Rapid advance (Rapid reverse)

By the remote control unit

Press SLOW/SEARCH (F, G) during play.

On the main unit

Press SEARCH (F, G) during play.

ÁThe speed of advance (reverse) is relatively slow at first.

When the button is pressed again, the speed becomes fast-

er. (Each time the button is pressed, the speed increases up

to 5 steps.)

ÁThe speed will be retained even after the button is released.

ÁNormal play is resumed when PLAY is pressed.

For your reference:

ÁWhen SLOW/SEARCH (F, G) or SEARCH (F, G)

is used during menu play of Video CDs with playback control,

a menu screen may sometimes be recalled.

ÁFor DVD and Video CDs, audio from 6CH DISCRETE or

MIXED 2CH output connectors will be heard during rapid

advance scanning at the initial scan speed. (See page 42.)

Frame advance (Frame reverse)

[DVD/Video CD]

Press the cursor buttons (C, D) in the still pic-

ture mode.

(See page 16.)

C: Reverse direction

D: Forward direction

ÁThe disc is advanced (reversed) by one frame each time the

cursor button (C, D) is pressed.

ÁWhen the cursor button (C, D) is kept pressed, consecutive

frame advance (reverse) works.

ÁNormal play is resumed when PLAY is pressed.

Note:

ÁFor Video CDs, frame reverse is not possible.

For your reference:

ÁPressing STILL/PAUSE or PAUSE also activates frame ad-

vance.

ÁWhether the pictures are advanced by a “Frame” or “Field” is

automatic. (See page 42.)

Reverse

direction

Forward

direction

(Example)

Forward

direction

Reverse

direction

Slow-motion play [DVD/Video CD]

By the remote control unit

Press SLOW/SEARCH (F, G) in the still pic-

ture mode.

(See page 16.)

On the main unit

Press SEARCH (F, G) in the still picture

mode.

(See page 16.)

ÁThe speed of slow-motion is slow at first. When the button is

pressed again, the speed becomes faster. (Each time the

button is pressed, the speed increases up to 5 steps.)

ÁThe speed will be retained even after the button is released.

ÁNormal play is resumed when PLAY is pressed.

Note:

ÁFor Video CDs, slow-motion playback in reverse direction is

not possible.

Enjoying Video CDs with

playback control without using

menus [Video CD]

1. Press STOP after the menu screen appears (after step 4 on

page 14).

(“PBC” will be cleared from the player’s FL display.)

2. Press the numeric buttons to select the preferred track.

(Play begins.)

ÁRefer to the jacket etc. of the disc concerned for the track

numbers.

ÁPress “1” to start play from the beginning of the disc.

To return to menu play

Press STOP to stop playback and press MENU.

(“PBC” will light up on the player’s FL display and the menu

screen is resumed.)

Perform step 5 on page 15.

(Example)

Forward

direction

Reverse

direction

Forward

direction

Reverse

direction

SLOW/

1818

General information about On-

Screen Menu Icons

This player features On-Screen Menu Icons providing various

functions. A “banner” will be displayed on the TV monitor by

pressing the ON SCREEN button on the remote control.

Operating the cursor buttons/SELECT button on the remote

control will show disc information (title/chapter/track number,

elapsed playing time, audio/subtitle language, and angle) and

player information (repeat play, play mode, marker, etc.).

Some icons allow the settings to be changed.

Common procedures

Press ON SCREEN during play or in the

stop mode.

Each time this button is pressed, the TV monitor changes

as shown below.

[>On-Screen Menu Icons are not displayed

l>On-Screen Menu Icons for selecting disc information

l On-Screen Menu Icons for selecting player information

{=Shuttle screen

ÁSome functions cannot be accessed from the stop

mode.

Press the cursor buttons (C, D) to select

the preferred item.

ÁThe currently selected item is indicated by the yellow

frame on the On-Screen Menu Icons.

Press the cursor buttons (A, B) to select

the preferred setting.

ÁFor some functions, the setting will be registered imme-

diately; for others, SELECT or PLAY must be pressed.

ÁWhen numbers are displayed (e.g. title No.), the numeric

buttons are also effective for setting instead of the cursor

buttons (A, B). When numbers are entered by the nu-

meric buttons, press SELECT to register the setting.

Press RETURN or CLEAR to clear the On-Screen Menu

Icons.

Examples of On-Screen Menu Icons

(See A, B and C for detailed illustration.)

(The screens may differ depending on the disc contents.)

ÁDVD (A) ÁVideo CD (B) ÁCD (C)

For your reference:

ÁDepending on the type of DVD software and a TV with auto-

matic picture zoom function enabled, the On-Screen Menu

Icons may not be displayed or only partially displayed on the

TV screen.

In this case, change the position of the On-Screen Menu

Icons in “4 On-Screen Messages” of the initial settings.

(See page 34.)

ÁThe color (blue, violet or green) of the On-Screen Menu

Icons can be changed. (See page 34.)

1 1:56:37 1

LPCM

ENG

148k 16

OFF

ENG

3:37

L R

OFF

PBC

PRG

3:37

PRG

OFF

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

PLAY

CLEAR

SELECT

RETURN

ON SCREEN

OFF

Operation Using

On-Screen Menu Icons

Detailed descriptions of each On-Screen Menu Icon

Screen for disc information (For DVD)

Chapter No.

Change the chapter No. by using the cursor buttons (A, B) or the numeric buttons and

press SELECT.

Audio soundtrack

language No.

(See page 27.)

Audio soundtrack

language

LPCM

dts

Vocal

Change the No. by using the

cursor buttons (A, B) or the

numeric buttons.

ENG: English POR: Portuguese

FRA: French RUS Russian

DEU: German JPN: Japanese

ITA: Italian CHI: Chinese

ESP: Spanish KOR: Korean

NLD: Dutch MAL: Malay

SVE: Swedish VIE: Vietnamese

NOR: Norwegian THA: Thai

DAN: Danish U: Others

Linear PCM

(“k” stands for kHz

and “b” stands for bit.)

Dolby Digital

dts

DVD Karaoke (Solo)

DVD Karaoke (Duet)

16b

20b

24b

Audio

attribute

96k

48k

1–5.1ch

--- (OFF)

V1oV2

Change the No. by using the

cursor buttons (A, B) or the

numeric buttons.

ENG: English POR: Portuguese

FRA: French RUS Russian

DEU: German JPN: Japanese

ITA: Italian CHI: Chinese

ESP: Spanish KOR: Korean

NLD: Dutch MAL: Malay

SVE: Swedish VIE: Vietnamese

NOR: Norwegian THA: Thai

DAN: Danish U: Others

Select “ON” or “OFF” by using

the cursor buttons (A, B).

OFF Subtitle is cleared.

ON Subtitle is displayed.

Subtitle language No.

(See page 28.)

Subtitle language

Subtitle on/off

For your reference:

Á“Ô Õ” around the icon means that the item can be changed using the cursor buttons (A, B).

Title No. Change the title No. by using the cursor buttons (A, B) or the numeric buttons and press SELECT.

Angle No.

(See page 29.)

Change the No. by using the cursor buttons (A, B) or the

numeric buttons.

Elapsed playing time

(hour: minute: second)

Change the time by using the numeric buttons and press SELECT.

It can be used to find a specific scene quickly.

Example: To specify “1 hour 56 min. 37 sec.”, enter “15637”.

(This function does not work with some discs.)

2020

Playback control

(Video CD only)

(See page 15.)

OFF Menu play is not ON.

ON Menu play is ON.

Detailed descriptions of each On-Screen Menu Icon

Screen for disc information (For Video CD/CD)

Track No.

Change the track No. by using the cursor buttons

(A, B) or the numeric buttons and press SELECT.

Elapsed playing time

(minute: second)

During CD play, display is changed by using the cursor

buttons (A, B).

Elapsed playing time>

Remaining time of the track

^-----Remaining time of the disc(--}

Audio mode

(Video CD only)

(See page 27.)

Change the mode by using the cursor buttons (A, B).

Left channel sound is output from the speaker (L),

and right channel sound from the speaker (R).

Left channel sound only is output.

Right channel sound only is output.

Note:

ÁTrack No. and the elapsed playing time are not displayed during menu play of Video CDs with playback control.

ÁIt is not possible to turn playback control ON or OFF using the On-Screen Menu Icons.

For your reference:

Á“Ô Õ” around the icon means that the item can be changed using the cursor buttons (A, B).

Operation Using

On-Screen Menu Icons

Screen for player information

Notes:

ÁRepeat play and marker functions do not work with an interactive DVD or during menu play of a Video CD with playback control.

ÁA-B repeat play does not work with an interactive DVD.

ÁIt is not possible to change the play mode using the On-Screen Menu Icons.

For your reference:

ÁThe master volume can be set and stored separately for DVD, Video CD and CD.

A-B repeat play

(See page 24.)

Press SELECT during play to store location A and press SELECT again to store location B and to start

repeat play between the specified two locations. Press SELECT again to return to normal play.

Marker

(See page 26.)

Press SELECT during play

and press SELECT again

at the preferred point to

store a marker. (Marker

no. is displayed instead of

“U”.)

ÁTo recall a marker, select

the preferred marker no.

by using the cursor

buttons (C, D) and enter

the selection using the

cursor button (A).

ÁTo clear a marker, select

the preferred marker no.

using the cursor buttons

(C, D) and press

CLEAR.

Adjust the master volume by

using the cursor buttons

(A, B).

0 to p127 dB or p¨

Master

volume

Contrast (o7 to p7) Equalizer (o1/0/p1) Brightness (0 to 15)

Repeat play

(See page 23.)

Select the preferred mode during play by

using the cursor buttons (A, B).

OFF

Normal play

Chapter repeat play

Title repeat play

Normal play

Track repeat play

Disc repeat play

DVD

Video CD/

ÁDVD

Cinema Dialogue

(See page 15.)

ÁVideo CD/CD

Play mode

(See pages 25 and 26.)

OFF

PRG

RND

---

Normal

volume

Louder

volume

Program

play

Random

play

Normal

play

Select the

preferred mode

during play by

using the cursor

buttons (A, B).

Cinema

Image

(DVD/Video

CD only)

Select the preferred mode by using the cursor buttons (A, B).

N Normal mode F Fine mode

S Soft mode C Cinema mode

User selection mode (Adjust the picture quality as you like.)

When “U” is selected and SELECT is pressed, the On-Screen Menu Icon as shown below appears.

Select the preferred item by using the cursor buttons (C, D) and select the preferred value by using the

cursor buttons (A, B).

Color hue (o7 to p7)

2222

For your reference:

ÁEach time the cursor button (C, D) is pressed, the speed of rapid reverse/advance and slow-motion play increases up to 5 steps.

ÁThe figures appearing at both ends of the shuttle screen stand for the maximum speeds of rapid reverse and rapid advance.

(DVD: o100/p100, Video CD: o40/p40, CD: o50/p50)

Detailed descriptions of each On-Screen Menu Icon

Shuttle screen

Still/Pause Press the cursor button (A).

Slow-motion play

(Backward)

Press the cursor button (C).

(DVD only)

Slow-motion play

(Forward)

Press the cursor button (D).

(DVD/Video CD only)

Rapid advance Press the cursor button (D).Rapid reverse Press the cursor button (C).

Play Press the cursor button (B).

Operation Using

On-Screen Menu Icons

Advanced Operation

Repeat play

Repeat viewing (listening)

Press REPEAT during play.

Each time this button is pressed, the TV monitor changes as

shown below and the disc will repeat a chapter or title (DVD) or

a track (Video CD/CD).

ÁDVD

Normal play

Repeat of chapter being played

Repeat of title being played

Cancel repeat mode

(Normal play)

ÁVideo CD/CD

Normal play

Repeat of track being played

Repeat of entire disc contents

Cancel repeat mode

(Normal play)

To return to normal play

Press REPEAT several times until “' OFF” is displayed.

Notes:

ÁRepeat play may not work correctly with some DVDs.

ÁRepeat play does not work with an interactive DVD or during

menu play of a Video CD with playback control.

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

OFF

2424

Repeat play

To enjoy program repeat play

If REPEAT is pressed during program play (see page 25), the

display changes as follows:

Program play

Repeat of programmed track

being played

Repeat of all programs

Cancel repeat mode

(Program play)

To return to program play

Press REPEAT several times until “' OFF” is displayed.

Repeating sections between two

specific points (A-B repeat)

Press A-B during play at the point where re-

peat play is to start (A).

Press A-B at the point where repeat play is

to be concluded (B).

Repeat play of the selection between points A and B starts.

To return to normal play

Press A-B several times until “' Á Á” is displayed.

Notes:

ÁA-B repeat play does not work with an interactive DVD.

ÁSome subtitles recorded around point A or B may fail to ap-

pear. [DVD]

ÁA-B repeat play works only within a title [DVD] or a track

[Video CD/CD].

For your reference:

ÁIf the title/track is completed before end location B is speci-

fied, the end point of the title/track serves as end location B.

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

STOP

PLAY

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

PLAY MODE

REPEAT

A-B

CLEAR

SLOW/

SELECT

T PRG

OFF

PRG

A •

A B

Advanced Operation

The player plays the tracks on the disc in an order you specify.

Press PLAY MODE in the stop mode.

The program playback screen appears on the TV monitor.

ÁTo exit the screen

Press PLAY MODE twice.

Press the cursor buttons (A, B, C, D) to

select the preferred track number.

Press SELECT.

The selected track is stored in the memory.

ÁRepeat steps 2 and 3 to select another track.

ÁUp to 18 tracks can be programmed.

Press PLAY.

Play now begins in the programmed sequence.

After playback

Play is stopped and the program playback screen is displayed.

Example: a disc

including 17 tracks

To return to normal play

1. Press STOP. (Program play is suspended.)

2. Press PLAY MODE twice.

3. Press PLAY.

Normal play begins from the beginning of the disc.

(The content of the program is still retained in the memory.)

Clearing the program

When the program playback screen is displayed

ÁTo clear the last program one by one

Move to “Clear last” and press SELECT.

(Pressing CLEAR of the remote control unit also clears the

last program.)

ÁTo clear all the programs

Move to “Clear all” and press SELECT.

(The programs are also cleared when the player is set to the

standby mode or turned off, or OPEN/CLOSE is pressed.)

Programming track numbers while monitoring

the player’s FL display

This function works with the following discs.

ÁCDs

ÁVideo CDs with playback control when menu play is can-

celled

(Press STOP while the menu screen is displayed.)

ÁVideo CDs which do not support playback control (Ver 1.1)

1. Press PLAY MODE once in the stop mode.

2. Press the numeric buttons to select the track.

The selected track is stored in the memory.

ÁRepeat step 2 to select another track.

3. Press PLAY.

Program play starts.

Program play [Video CD/CD]

In the case of a CD

Choose a track, then press SELECT.

Clear last

Clear all

Press PLAY to start

113

214

315

41610

51711

612

Clear last

Clear all

Press PLAY to start

113

214

315

41610

51711

612

Choose a track, then press SELECT.

Clear last

Clear all

Press PLAY to start

113 2

214

315

41610

51711

612

Choose a track, then press SELECT.

Flashes

Track No.

Program No.

2626

Random play [Video CD/CD]

The player plays the tracks on the disc in random order.

Press PLAY MODE twice in the stop mode.

The random playback screen appears on the TV monitor.

ÁTo exit the screen

Press PLAY MODE once.

Press PLAY.

Play now begins in random order.

After playback

Play is stopped and the random playback screen is displayed.

To return to normal play

1. Press STOP. (Random play is suspended.)

2. Press PLAY MODE once.

3. Press PLAY.

Normal play begins from the beginning of the disc.

Storing markers in memory to be

viewed (listened to) again

Storing a marker in the memory

Press MARKER during play.

The marker screen appears on the TV monitor.

Press SELECT during play at the starting

point to be viewed (listened to) again.

Indicates “MARKER 1” is stored

in the memory.

(If SELECT is pressed where any

number is already displayed, the

previous starting point will be

replaced by the new one.)

ÁUp to 5 markers can be stored in the memory.

ÁPress MARKER to clear the display.

“U” indicates no

marker has

been stored yet.

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

STOP

PLAY

AUDIO

MARKER

PLAY MODE

CLEAR

SELECT

Random Playback

Press PLAY to start

UUUUU

UUUU

Advanced Operation

Storing markers in memory to be viewed

(listened to) again

Recalling/clearing a marker

Press MARKER during play.

Press the cursor buttons (C, D) to select

the marker to be recalled/cleared.

Press the cursor button (A) to recall a mark-

er.

Press CLEAR to clear a marker.

Play resumes from the point corresponding to the selected

marker.

The selected marker is cleared. (Press MARKER to clear the

display.)

Notes:

ÁSome subtitles recorded around the marker may fail to ap-

pear. [DVD]

ÁThese operations do not work with an interactive DVD or dur-

ing menu play of a Video CD with playback control.

For your reference:

ÁAll the markers are cleared when the player is set to the

standby mode or turned off, or OPEN/CLOSE is pressed.

Changing audio soundtrack

language [DVD]

It is possible to change the audio soundtrack language to a

different language from the one selected at the initial settings.

(If available. See page 31.)

(This operation works only with discs on which multiple audio

soundtrack languages are recorded.)

Press AUDIO during play.

ÁWhen no audio soundtrack is recorded, “–” will be dis-

played instead of the language number.

Press the cursor buttons (A, B) until the

preferred language is selected.

Pressing the numeric

buttons also changes the

audio soundtrack

language.

ÁPress AUDIO or SELECT to

clear the display.

For your reference:

ÁWhen the preferred language is not selected, even after

pressing the cursor buttons (A, B) several times, it means

that language is not available on the disc.

ÁWhen the power is turned on, or the disc tray is opened, the

language heard is the one selected at the initial settings. If

this language is not recorded on the disc, only the available

language on the disc will be heard.

Switching vocals ON or OFF for

Karaoke discs [DVD/Video CD]

Press AUDIO during play.

Press the cursor buttons (A, B, C, D) until

the preferred setting is selected.

ÁDVD Karaoke (Solo) (C, D)

–––(OFF)()ON

ÁDVD Karaoke (Duet) (C, D)

–––(OFF)>1o2 (ON)>V1 (ON)>V2 (ON)

^-----------------------------------------------------------------}

ÁVideo CD (A, B)

LR>L>R

^--------------}

ÁPress AUDIO or SELECT to clear the display.

Note:

ÁThis operation does not work with CDs.

Number of the audio

soundtrack language

being played back

1 2 3 4

Hello

LPCM

ENG

96k 24

LPCM

FRA

96k 24

Bonjour

Vocal

---

Vocal

L R

2828

Changing subtitle language [DVD]

It is possible to change the subtitle language to a different

language from the one selected at the initial settings.

(If available. See page 31.)

(This operation works only with discs on which multiple subtitle

languages are recorded.)

Press SUBTITLE during play.

ÁWhen no subtitles are recorded, “––” will be displayed

instead of the language number.

Press the cursor buttons (A, B) until the

preferred language is selected.

Pressing the numeric

buttons also changes the

subtitle language.

ÁPress SUBTITLE or SELECT to clear the display.

To clear/display the subtitles

Press the cursor buttons (C, D) to select ON or OFF at step 2.

Notes:

ÁIn some cases, the subtitle language is not changed to the

selected one immediately.

ÁWhen a disc supported the closed caption is played, the sub-

title and the closed caption may overlap each other on the TV

monitor. In this case, turn the subtitle off.

For your reference:

ÁWhen the preferred language is not selected even after

pressing the cursor buttons (A, B) several times, it means

that the language is not available on the disc.

ÁWhen the power is turned on or the disc tray is opened, sub-

titles appear in the language selected at the initial settings. If

this language is not recorded on the disc, they appear in the

disc’s priority language.

Number of the subtitle

language being played

back

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

TITLE

PLAY

SUBTITLE

ANGLE

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

SELECT

I love you

ENG

Je t’aime

FRA

Advanced Operation

Viewing from another angle [DVD]

Some DVDs may contain scenes which have been shot simul-

taneously from a number of different angles. For these discs,

the same scene can be viewed from each of these different

angles using the ANGLE button. (The recorded angles differ

depending on the disc used.)

Press ANGLE during play.

Press the cursor buttons (A, B) until the

preferred angle is selected.

Pressing the numeric buttons

also changes the angle.

ÁPress ANGLE or SELECT to clear the display.

Note:

ÁThis function only works for titles having scenes recorded at

different angles.

For your reference:

Á“ANGLE” lights up on the player’s FL display at scenes re-

corded at different angles to indicate that angle switching is

possible.

ÁThe angle number can be programmed beforehand with

some DVDs; the angle will be switched to the selected

number when “ANGLE” lights up.

Number of angle being

played back

Using a title menu [DVD]

Some discs with movies, for example, may be available with

two or more titles. If the disc has a title menu recorded on it,

the TITLE button can be used to select the movie title.

(The details of operation differ depending on the disc used.)

Press TITLE during play.

A list of the titles on the

disc is now displayed.

ÁPressing TITLE again resumes play from the scene

when TITLE was first pressed.

Press the cursor buttons (A, B, C, D) and

press SELECT or PLAY, or press the numer-

ic buttons, to select the preferred title.

The selected title now starts playing.

Using a DVD menu [DVD]

Some DVDs have unique menu structures called DVD menus.

For example, DVDs programmed with complex contents pro-

vide guide menus, and those recorded with various languages

provide menus for audio and subtitle language. Although the

DVD menu’s contents and operation differ from disc to disc,

the following explains basic operation when this feature is

used.

Press MENU during play.

The DVD menu available on the

disc is now displayed.

ÁPressing MENU again resumes play from the scene

when MENU was first pressed.

Press the cursor buttons (A, B, C, D) and

press SELECT, or press the numeric but-

tons, to select the preferred item.

The selected item is now executed.

When the menu continues onto another screen

Repeat step 2.

(Example)

TITLE MENU

Dogs

Lovers

Castles

Birds

TITLE MENU

Dogs

Lovers

Castles

Birds

of the world

DVD MENU

1.SUBTITLE

2.AUDIO

3.ANGLE

DVD MENU

1.SUBTITLE

2.AUDIO

3.ANGLE

3030

Initial settings

Once the intial settings have been completed, the player can

always be operated under the same conditions (especially with

DVD discs).

The settings will be retained in the memory, until the settings

are changed, even after switching to standby mode.

Common procedures of initial settings

Press SET UP in the stop mode.

Press the cursor buttons (A, B) to select

the preferred item and press SELECT.

Each screen for setting the value is displayed.

1 Disc Languages (see page 31)

2 Ratings (see page 32)

3 Menu Language (see page 33)

4 On-Screen Messages (see page 34)

5 FL Display (see page 35)

6 TV Aspect (see page 36)

7 Digital Audio Output (see page 38)

8 Speaker Setting (see page 40)

9 Other Settings (see page 42)

Press the cursor buttons (A, B) to select

the preferred value and press SELECT.

ÁSome items require additional steps. (See the respec-

tive page.)

To cancel during setup operation

Press RETURN or select “0”. (The previous screen is dis-

played.)

To clear the initial settings screen

Press the cursor buttons (A, B) to select “0” and press

SELECT. (Pressing SET UP or RETURN also clears the initial

settings screen.)

Note:

ÁAfter the player is set to the “Lock All” setting in “2 Ratings”,

none of the initial settings, including “2 Ratings”, can be

changed if the DVD disc is left inside the player. In this case,

remove the disc, and unlock the player.

For your reference:

ÁThe numeric buttons can also be used for selecting items or

values instead of the cursor buttons (A, B); in this case,

pressing SELECT is not necessary.

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

RETURN

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

CLEAR

SLOW/

SELECT

1 Disc Languages

Level 8

2 Ratings

3 Menu Language

4 On-Screen Messages

5 FL Display

6 TV Aspect

7 Digital Audio Output

8 Speaker Setting

9 Other Settings

0 Exit

English

Bright

4:3

Initial Settings

Selecting disc languages [DVD]

This is to select the audio soundtrack language, subtitle lan-

guage and the language used in title menus or DVD menus

which will always be used for every disc to be played back.

At the initial settings screen (on page 30)

Press the cursor buttons (A, B) to select

“1 Disc Languages” and press SELECT.

Press the cursor buttons (A, B) to select

the preferred item and press SELECT.

1 Audio:

To select the audio soundtrack language.

2 Subtitle:

To select the subtitle language.

3 Menus:

To select the language used in title menus or DVD

menus.

Press the cursor buttons (A, B) to select

the preferred language and press SELECT.

When “1 Audio” is selected

1 English: English is selected. (Factory preset)

2 French/3 Spanish:

Each language is selected.

4 Original: The original language of each disc will

be selected.

5 Other UUUU: Another language can be selected.

(Refer to the language codes on

page 44. Press CLEAR if an incorrect

language code is entered.)

When “2 Subtitle” is selected

1 Automatic: The same language selected for the

“1 Audio” will be selected.

(Factory preset)

ÁIf the language selected for the “1

Audio” is actually used during play-

back, the subtitles will not appear.

ÁIf another language is used during

playback, the subtitles will appear in

the language selected at the setup

“1 Audio”.

2 English/3 French/4 Spanish:

Each language is selected.

5 Other UUUU: Another language can be selected.

(Refer to the language codes on

page 44. Press CLEAR if an incorrect

language code is entered.)

When “3 Menus” is selected

1 English: English is selected. (Factory preset)

2 French/3 Spanish:

Each language is selected.

4 Other UUUU: Another language can be selected.

(Refer to the language codes on

page 44. Press CLEAR if an incorrect

language code is entered.)

The screen illustrated in step 1 is displayed. Select “0” by

using the cursor buttons (A, B) and press SELECT to return

to the initial settings screen.

Also refer to “Common procedures of initial settings” on

page 30.

Note:

ÁIf the language selected is not available on the disc, the lan-

guage designated by each disc will be selected.

Disc Languages

1 Audio

2 Subtitle

3 Menus

Automatic

English

0 Exit

English

3232

Initial settings

Selecting rating level [DVD]

This is to disable the playing of specified DVDs which are un-

suitable for children.

ÁSome DVDs are encoded with a specific rating level. If the

rating level of the disc is higher than that preset in the initial

settings operation, playback of the disc will be prohibited.

At the initial settings screen (on page 30)

Press the cursor buttons (A, B) to select

“2 Ratings” and press SELECT.

Press the cursor buttons (A, B) to select

the preferred level and press SELECT.

Level 8: All DVDs can be played back.

(Factory preset)

Level 7 to 2: DVDs for general audiences/children can

be played back.

(DVDs for adults are prohibited.)

Level 1: DVDs for children can be played back.

(DVDs for adults/general audiences are

prohibited.)

Level 0: Playback of all DVDs is prohibited (e.g. to

prohibit playback of DVDs for adults which

are not encoded with rating level

information).

When level 7 or lower is selected

Input a 4-digit password by pressing the

numeric buttons and press SELECT.

The lock symbol

appears closed to

show the rating is

locked.

Example: “4343”

Do not forget your

password.

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

SELECT

Please set a rating limit

8 No Limit

0 Lock All

Press RETURN to cancel

Ratings

Enter a 4-digit password,

then press SELECT.

Press RETURN to cancel

The player is locked.

Remember the password.

Ratings

Press SELECT to continue

Initial Settings

Press SELECT.

Setting is finished and the initial settings screen is displayed.

ÁThe rating is locked. Any discs whose rating is higher than

the setting cannot be played back unless the correct pass-

word is entered.

When the player is locked

The following screen appears when “2 Ratings” is selected at

the initial settings screen.

1. Input a 4-digit password and press SELECT.

2. To unlock the player

Press “1” and then press SELECT.

To change the password

Press “2”, enter a new 4-digit password and press

SELECT, then press SELECT again.

To change the rating level

Press “3”, select a new level by pressing the cursor buttons

(A, B), then press SELECT.

To unlock the player temporarily

Press “4” and then press SELECT.

ÁThe rating is unlocked temporarily only for the current disc

or only until the player is set to the standby mode.

To finish setting without changing the rating level

Press “0”.

Setting is finished and the initial settings screen is displayed.

Also refer to “Common procedures of initial settings” on

page 30.

Note:

ÁSome discs may not be encoded with specific rating level

information though its disc jacket says that it is for “adults”.

For those discs, the age restriction will not work.

Selecting language of On-Screen

Display menu

This is to select the language to be used in the On-Screen Dis-

play menus which the player will show on the TV monitor.

At the initial settings screen (on page 30)

Press the cursor buttons (A, B) to select

“3 Menu Language” and press SELECT.

Press the cursor buttons (A, B) to select

the preferred language and press SELECT.

1 English:

English is selected. (Factory preset)

2 Français/3 Español:

Each language is selected.

Setting is finished and the initial settings screen is displayed.

Also refer to “Common procedures of initial settings” on

page 30.

Press RETURN to cancel

Ratings

Enter your 4-digit password,

then press SELECT.

0 Exit

Ratings

1 Unlock Player

2 Change Password

3 Change Level

4 Temporary Unlock

Press RETURN to cancel

Select the language

for these Menus.

1 English

2 Français

3 Español

3434

Initial settings

Selecting the display format of the

On-Screen Display

You can select whether “Play”, “Still” and other displays will be

displayed or not, and the color and position of “Play”, “Still” and

other displays as well as On-Screen Menu Icons.

At the initial settings screen (on page 30)

Press the cursor buttons (A, B) to select

“4 On-Screen Messages” and press

SELECT.

Press the cursor buttons (A, B) to select

the preferred item and press SELECT.

1 On-Screen Messages:

To select whether “Play”, “Still” and other displays are

displayed or not.

2 Color and Position:

To select the color (Blue/Violet/Green) and position

(above/slightly below) of “Play”, “Still” and other dis-

plays as well as On-Screen Menu Icons.

Press the cursor buttons (A, B) to select

the preferred setting and press SELECT.

When “1 On-Screen Messages” is selected

1 On: “Play”, “Still” and other displays will always ap-

pear on the TV screen. (Factory preset)

2 Off: “Play”, “Still” and other displays will not appear

on the TV screen.

When “2 Color and Position” is selected

The colors and positions are set as follows:

1 Blue (Factory preset)

2 Violet

3 Green

4 Blue

5 Violet

6 Green

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

SELECT

STILL/PAUSE

SLOW/

On-Screen Messages

Color and Position Blue

0 Exit

Initial Settings

The screen illustrated in step 1 is displayed. Select “0” by

using the cursor buttons (A, B) and press SELECT to return

to the initial settings screen.

Also refer to “Common procedures of initial settings” on

page 30.

For your reference:

ÁWhen is selected, “Play”, “Still” and other displays

as well as On-Screen Menu Icons will be displayed at a little

lower position than the factory setting. It is recommended to

choose this setting in such a case that the screen is only par-

tially displayed.

Selecting the FL display brightness

This is to select the brightness of the player’s FL display.

At the initial settings screen (on page 30)

Press the cursor buttons (A, B) to select

“5 FL Display” and press SELECT.

Press the cursor buttons (A, B) to select

the preferred item and press SELECT.

1 Bright:

The FL display will always be bright. (Factory preset)

2 Dim:

The FL display will always be dimmed.

3 Dim During DVD/VCD Play (Auto):

The FL display will be dimmed during playback of

DVDs and Video CDs.

Setting is finished and the initial settings screen is displayed.

For your reference:

ÁEven if “3 Dim During DVD/VCD Play (Auto)” is selected, the

display resumes brightness when a button for special play

such as SLOW/SEARCH and STILL/PAUSE is pressed.

Also refer to “Common procedures of initial settings” on

page 30.

FL Display

Press RETURN to cancel

1 Bright

2 Dim

Dim During DVD/VCD Play (Auto)

Initial settings

Selecting TV screen type

Select the TV aspect, conventional size screen (4:3) or wide-

screen (16:9), and the TV type according to your TV set.

At the initial settings screen (on page 30)

Press the cursor buttons (A, B) to select

“6 TV Aspect” and press SELECT.

Press the cursor buttons (A, B) to select

the TV aspect and press SELECT.

1 4:3:

Select when a conventional TV set is connected.

(Factory preset)

2 16:9:

Select when a wide-screen TV set is connected.

Press the cursor buttons (A, B) to select

the TV type and press SELECT.

When “4:3” is selected

When “16:9” is selected

Following TV types can be selected in both cases.

1 Standard (Direct View TV):

Select when a standard TV (Direct view) is connected.

(Factory preset)

2 CRT Projector:

Select when a CRT projector is connected.

3 LCD Projector:

Select when a LCD projector is connected.

4 Projection TV:

Select when a projection TV is connected.

Setting is finished and the initial settings screen is displayed.

Also refer to “Common procedures of initial settings” on

page 30.

For your reference:

ÁFor further details on the images which appear on the TV

screen (aspect ratios of the screen), see page 37.

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

SELECT

Select your TV aspect

1 4 : 3

2 16 : 9

Press RETURN to cancel

Initial Settings

ÁThe images which appear on the TV screen, and what each screen mode is called, may differ depending on the manufacturer of the

TV set or on the type of the TV set. Consult the instruction manual provided with your TV set.

For your reference:

ÁLetterbox

Black bands are inserted at the top and bottom of the screen to fill in the gaps at the top and bottom where the size of the picture is

smaller than the screen.

ÁPan & Scan

Part of the wide-screen picture (either at both sides or one side of the screen) is automatically eliminated so that the picture fills the

whole screen.

Concerning images which appear on the TV screen (aspect ratios of the screen)

Images which appear on the TV screen differ depending on the type of software and the TV set connected.

4:3

Screen whose right and

left edges are cut off

Letterbox (with black

bands at top and

bottom)

Full screen

Letterbox (with black

bands at top and

bottom

TV set connected (Screen mode)

Type of software

Software for wide-

screen (formatted

in the Pan & Scan

style)

Software for wide-

screen (not

formatted in the

Pan & Scan style)

Software (4:3)

Software

(4:3, Letterbox)

16:9 (“FULL” mode)

Full screen

Screen horizontally

enlarged

Screen horizontally

enlarged (with black

bands at top and

bottom)

16:9 (“ZOOM” mode)

Screen whose top and

bottom edges are cut

off

Screen whose top and

bottom edges are cut

off

Full screen

16:9 (“AUTO” mode)

Full screen

(with black bands at

right and left)

Screen in which the

picture at the far left

and far right ends only

is extended horizontally

(with black bands at top

and bottom)

Initial settings

Selecting digital output

Select the digital output to be output from the optical/coaxial

digital audio output connector of the player.

At the initial settings screen (on page 30)

Press the cursor buttons (A, B) to select

“7 Digital Audio Output” and press

SELECT.

Press the cursor buttons (A, B) to select

the preferred item and press SELECT.

1 LPCM 96k>48k:

To select whether digital audio converted to 48 kHz/

16 bit is output from the optical/coaxial digital audio

output connector or no digital audio is output during

playback of the DVD recorded in Linear PCM of

96 kHz.

(In case of the DVD recorded in Linear PCM of 48 kHz,

digital audio converted to 48 kHz/16 bit is output irre-

spective of the setting.)

2 Dolby Digital:

To select the signal format (Bitstream or PCM) to be

output from the optical/coaxial digital audio output con-

nector during playback of the DVD recorded in Dolby

Digital.

3 dts:

To select whether dts bitstream is output from the opti-

cal/coaxial digital audio output connector or no digital

audio is output during playback of the DVD recorded in

dts.

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

SELECT

Digital Audio Output

LPCM 96k 48k

0 Exit

Dolby Digital

3 dts

Bitstream

Off

Initial Settings

Press the cursor buttons (A, B) to select

the preferred value and press SELECT.

When “1 LPCM 96k>48k” is selected

1 No: Digital audio of 48 kHz/16 bit is output during

playback of the DVD recorded in Linear PCM of

48 kHz. No digital audio is output during play-

back of the DVD recorded in Linear PCM of

96 kHz. However, audio will be output using the

original audio recording system in case of the

DVD which has not been copyright-protected.

(Factory preset)

2 Yes: During playback of the DVD recorded in Lin-

ear PCM of 48 kHz or 96 kHz, digital audio con-

verted to 48 kHz/16 bit is output.

(Digital output of PCM audio is restricted to

48 kHz/16 bit or below for copyright protection.)

When “2 Dolby Digital” is selected

1 Bitstream: Dolby Digital bitstream (1ch–5.1ch) is

output during playback of the DVD

recorded in the Dolby Digital. (Factory

preset)

Select this setting when the player is

connected to the Dolby Digital decoder.

2 PCM

: Digital audio converted to PCM (2ch) of

48 kHz/16 bit is output during playback of

the DVD recorded in the Dolby Digital.

When “3 dts” is selected

1 Off

: No digital audio is output during playback

of the DVD recorded in dts.

(Factory preset)

2 Bitstream: dts bitstream is output during playback of

the DVD recorded in dts.

Select this setting when the player is

connected to the dts decoder.

The screen illustrated in step 1 is displayed. Select “0” by us-

ing the cursor buttons (A, B) and press SELECT to return to

the initial settings screen.

Also refer to “Common procedures of initial settings” on

page 30.

Recommended setting of “Digital Audio Out-

put”

Make settings as shown in table below depending on the kind

of equipment that is connected to the optical/coaxial digital au-

dio output connector.

ÁUnderlined item is a factory preset.

When connecting an AV amplifier (with an optical/coaxial

digital audio input connector) without Dolby Digital or dts

decoder, be sure to select “PCM” of “2 Dolby Digital” and

“Off” of “3 dts”. If “Bitstream” is selected, any attempt to play

DVD may cause such a high level of noise that it may be

harmful to your ears and damage your speakers.

When “PCM” is selected and “Yes” is selected for the speak-

ers other than the front speakers at “8 Speaker Setting” (see

page 40), only audio corresponding to the front speakers will

be output from the player’s digital audio output connector

during playback of the DVD recorded in Dolby Digital 5.1 ch

surround. In this case, select “No” for the speakers other

than the front speakers at “8 Speaker Setting”.

The audio which is output from the player’s audio output

connectors (6CH DISCRETE and MIXED 2CH) is also set to

the Linear PCM 48 kHz sound quality level.

To enjoy high quality sound at 96 kHz, connect the amplifier

or decoder directly to the audio output connectors, not to the

digital audio output connector. (Select “No” at the “1 LPCM

96k>48k”.)

Type of equipment

to be connected

No equipment is

connected

AV amplifier (with

digital audio input

connector) without

Dolby Digital/dts

decoder

AV amplifier with

Dolby Digital decoder

(See page 10.)

AV amplifier with

Dolby Digital/dts

decoder

(See page 10.)

Recommended setting

1 LPCM

96k>48k

Yes

3 dts

Off

Bitstream

2 Dolby

Digital

Bitstream

PCM

Bitstream

Initial settings

Speaker settings

At the initial settings screen (on page 30)

Press the cursor buttons (A, B) to select

“8 Speaker Setting” and press SELECT.

ÁUnderlined item is a factory preset.

Press the cursor buttons (A, B, C, D) to

select the preferred item and press

SELECT.

Press the cursor buttons (A, B) to select

the preferred value and press SELECT.

Speaker icons:

ÁIf the speaker is connected, display the icon by using the

cursor buttons (A, B) and pressing SELECT.

ÁIf the speaker supports low-frequency (under 100 Hz)

reproduction, select the larger icon. If the speaker does

not support low-frequency (under 100 Hz) reproduction,

select the smaller icon. [When the subwoofer is not con-

nected, be sure to select “Large” for the front speakers

(L/R).]

Center

Large/Small/

Center

Delay time (

0 ms)

Front (L)

Large/Small

Test

signal

Surround (L)

Large/Small/No

Surround (L)

Channel balance (

0 dB)

Surround (R)

Large/Small/

Surround (L/R)

Delay time (

0 ms)

Subwoofer

Channel balance

(

0 dB)

Subwoofer

Yes/

Front (R)

Large/Small

Center

Channel balance (

0 dB)

In the case of surround speaker (L)

ÁLarge/Yes

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

SELECT

L R

Press RETURN to cancel

Speaker Setting

Exit

Test

Exit

ÁSmall/Yes ÁNo

Surround (R)

Channel balance (

0 dB)

Initial Settings

Delay time:

If the surround speakers or the center speaker can not be

installed at an equal distance to the front speakers from

the listening position, change the delay time to get better

surround effect.

ÁWhen D2 or D3 is equal to or larger than D1, no setting is

necessary. Otherwise, change the setting according to

the table below.

Ideal position of the

center speaker

It is recommended to locate all the

speakers inside of this circle.

Ideal position

of the

surround

speakers

To adjust the channel balance using the test signal:

1. Select “Test” by using the cursor buttons (A, B, C,

D), and then press SELECT.

(Test signals will be output clockwise from each speak-

er except the subwoofer consecutively.)

2. While listening to the test signal, adjust the volume of

each speaker so that all the test signals are heard at

the equal level.

3. Press SELECT. (The test signals are stopped.)

Note:

ÁTest signal is not output from the subwoofer. Adjust the

channel balance for each disc to be played back.

Press the cursor buttons (A, B, C, D) to

select “Exit” and press SELECT.

Setting is finished and the initial settings screen is displayed.

Also refer to “Common procedures of initial settings” on

page 30.

FRONT (L)

SURROUND (L) SURROUND (R)

FRONT (R)CENTER

Speaker

Center

speaker

(D2)

Surround

speakers

(D3)

Delay time

01.3 ms

02.6 ms

03.9 ms

05.3 ms

10.6 ms

15.9 ms

Difference between D1

and D2/D3

approx. 1

/2 feet (50 cm)

approx. 03 feet (100 cm)

approx. 05 feet (150 cm)

approx. 06 feet (200 cm)

approx. 12 feet (400 cm)

approx. 18 feet (600 cm)

Initial settings

Other settings

Compression of the sound’s dynamic range and other special

settings can be performed.

At the initial settings screen (on page 30)

Press the cursor buttons (A, B) to select

“9 Other Settings” and press SELECT.

Press the cursor buttons (A, B) to select

the preferred item and press SELECT.

1 Still Mode:

To select “Field still” or “Frame still” to prevent jittering

from occurring or to let small text or fine patterns seen

clearly in the still picture mode.

2 Audio during Search:

To select whether audio is heard during search at the

initial scan speed or not.

3 TV Mode (4:3):

To select whether the video material for a wide-screen

will be played back in the Pan & Scan style or in the

Letterbox style on a conventional size TV.

4 D. (Dynamic) Range Compression:

To select the dynamic range during playback.

5 Still Picture Display:

To select whether the picture type (I/P/B) is displayed

on the TV screen in the still picture mode or not.

6 Black Level Control:

To select the black level of the picture, “Lighter” or

“Darker”.

Press the cursor buttons (A, B) to select

the preferred value and press SELECT.

When “1 Still Mode” is selected

1 Automatic: “Field still” and “Frame still” are automati-

cally selected in the still picture mode.

(Factory preset)

2 Field: “Field still” is always selected.

Select this setting when jittering occurs in

the pictures even when “1 Automatic” is

selected.

3 Frame: “Frame still” is always selected.

Select this setting when small text or fine

patterns cannot be seen clearly even

when “1 Automatic” is selected.

POWER

STOP

TITLE

SUBTITLE

MARKER

ANGLEAUDIO

ON SCREEN RETURN

SELECT

SKIP IF

PLAY

STILL/PAUSE

OPEN/CLOSE

*/ I

PLAY MODE

REPEAT

A-B CLEAR

DVD

SET UP

SLOW/

SELECT

Other Settings

1 Still Mode

2 Audio during Search

3 TV Mode (4:3)

4 D. Range Compression

0 Exit

Automatic

5 Still Picture Display

Pan&Scan

Off

6 Black Level Control

Lighter

Initial Settings

When “2 Audio during Search” is selected

1 On: Audio from 6CH DISCRETE or MIXED 2CH out-

put connectors will be heard during search at the

initial scan speed. (Factory preset)

2 Off: Select this setting when audio during search at

the initial scan speed is not desired.

When “3 TV Mode (4:3)” is selected

1 Pan & Scan: The video material for a wide-screen

will be played back in the Pan & Scan

style on a conventional size TV.

(Factory preset)

ÁVideo material not formatted in the

Pan & Scan style will be played back

in the letterbox style. (See page 37.)

2 Letterbox: The video material for a wide-screen

will be played back in the letterbox style

on a conventional size TV.

When “4 D. (Dynamic) Range Compression” is selected

1 Off: Normal audio range is selected. (Factory preset)

2 On: Select this setting to enjoy listening to dynamic

sound even on a low volume.

Dynamic range is the difference in volume

between the quietest and loudest sounds heard.

Dynamic Compression limits level for listening at

low volume. This is useful late at night, for

example.

[This function only works with Dolby Digital

DVD.]

When “5 Still Picture Display” is selected

1 Off: The picture type (I/P/B) will not be displayed on

the TV screen in the still picture mode.

(Factory preset)

2 On: The picture type (I/P/B) will be displayed on the

TV screen in the still picture mode.

When “6 Black Level Control” is selected

1 Lighter: The black level of the picture is selected to

the lighter one.

Select this setting normally when the player

is connected to a TV set through the VIDEO

OUT connector or S VIDEO OUT connector.

(Factory preset)

2 Darker: The black level of the picture is selected to

the darker one.

Select this setting normally when the player

is connected to a TV set through the COM-

PONENT VIDEO OUT (Y, C

B, CR) con-

nector.

The screen illustrated in step 1 is displayed. Select “0” by us-

ing the cursor buttons (A, B) and press SELECT to return to

the initial settings screen.

Also refer to “Common procedures of initial settings” on

page 30.

Predict

General Picture type

For your reference:

ÁWhen the “2 On” is selected at the “5 Still Picture Display”,

the following screen is displayed in the still picture mode;

ÁI/P/B:

The MPEG 2 standard adopted for DVD uses the following

3 picture types for the coding of each picture (frame) on the

TV screen.

I: I-Picture (Intra coded picture)

This is the standard picture type, and each picture is coded

separately. Since it features the best picture quality, it is rec-

ommended that the screen be frozen with I-Picture when the

picture quality is to be adjusted.

P: P-Picture (Predictive coded picture)

This picture type is computed on the basis of a past I-Picture

or P-Picture.

B: B-Picture (Bidirectionally-predictive coded picture)

This picture type is computed by comparing the previous and

subsequent I-Picture or P-Picture. It has the lowest volume of

information.

Example: in the case of the P-Picture

Still (P)

Language code list

Enter the appropriate code number for the initial settings “Audio”, “Subtitle” and/or “Menus” (see page 31).

Code

6565

6566

6570

6577

6582

6583

6588

6590

6665

6669

6671

6672

6678

6679

6682

6765

6779

6783

6789

6865

6869

6890

6976

6978

6979

6983

6984

6985

7065

7073

7074

Language

Afar

Abkhazian

Afrikaans

Ameharic

Arabic

Assamese

Aymara

Azerbaijani

Bashkir

Byelorussian

Bulgarian

Bihari

Bengali; Bangla

Tibetan

Breton

Catalan

Corsican

Czech

Welsh

Danish

German

Bhutani

Greek

English

Esperanto

Spanish

Estonian

Basque

Persian

Finnish

Fiji

Code

7079

7082

7089

7165

7168

7176

7178

7185

7265

7273

7282

7285

7289

7365

7378

7383

7384

7387

7465

7473

7487

7565

7575

7576

7577

7578

7579

7583

7585

7589

7665

Language

Faroese

French

Frisian

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Hindi

Croatian

Hungarian

Armenian

Interlingua

Indonesian

Icelandic

Italian

Hebrew

Japanese

Yiddish

Javanese

Georgian

Kazakh

Greenlandic

Cambodian

Kannada

Korean

Kashmiri

Kurdish

Kirghiz

Latin

Code

7678

7679

7684

7686

7771

7773

7775

7776

7778

7779

7782

7783

7784

7789

7865

7869

7876

7879

7982

8065

8076

8083

8084

8185

8277

8279

8285

8365

8368

8372

8373

Language

Lingala

Laothian

Lithuanian

Latvian, Lettish

Malagasy

Maori

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Malay

Maltese

Burmese

Nauru

Nepali

Dutch

Norwegian

Oriya

Panjabi

Polish

Pashto, Pushto

Portuguese

Quechua

Rhaeto-Romance

Romanian

Russian

Sanskrit

Sindhi

Serbo-Croatian

Singhalese

Code

8375

8376

8377

8378

8379

8381

8382

8385

8386

8387

8465

8469

8471

8472

8473

8475

8476

8479

8482

8484

8487

8575

8582

8590

8673

8679

8779

8872

8979

9072

9085

Language

Slovak

Slovenian

Samoan

Shona

Somali

Albanian

Serbian

Sundanese

Swedish

Swahili

Tamil

Telugu

Tajik

Thai

Tigrinya

Turkmen

Tagalog

Tonga

Turkish

Tatar

Twi

Ukrainian

Urdu

Uzbek

Vietnamese

Volapük

Wolof

Xhosa

Yoruba

Chinese

Zulu

Initial SettingsFor Your Reference

Disc handling and maintenance

Handling precautions

ÁHold the disc by the edges so the surface will not be soiled

with fingerprints. (A)

Fingerprints, dirt and scratches can cause skipping and dis-

tortion.

ÁDo not write on the label side with a ball-point pen or other

writing utensils.

ÁDo not use record cleaning sprays, benzine, thinner, static

electricity prevention liquids or any other solvent.

ÁBe careful not to drop or bend the disc.

ÁDo not install more than 1 disc on the disc tray.

ÁDo not try to close the disc tray when the disc is not installed

properly. (B)

ÁBe sure to store the disc in its exclusive case when not in

use.

If the surface is soiled C

Wipe gently with a soft, damp (water only) cloth.

When wiping discs, always move the cloth from the center hole

toward the outer edge.

(If you wipe the discs using a circular motion, circular scratch-

es are likely to occur, which will cause noise.)

If the disc is brought from a cold to a warm en-

vironment, moisture may form on the disc

Wipe this moisture off with a soft, dry, lint-free cloth before us-

ing the disc.

Improper disc storage

You can damage discs if you store them in the following

places:

ÁAreas exposed to direct sunlight

ÁHumid or dusty areas

ÁAreas directly exposed to a heat outlet or heating appliance

Discs which cannot be played with this player

ÁDVD with Region No. other than “1” or “ALL”

ÁDisc of PAL system ÁCD-G

ÁDVD-ROM ÁCD-RW

ÁDVD-R/DVD-RAM ÁDVDGRW

ÁCD-ROM ÁCVD

ÁVSD ÁSVCD

ÁCDV ÁDivx Video Disc

etc.

ÁDo not try to play Photo CD or CD-R.

(Otherwise, data on the disc may be damaged.)

To prevent a malfunction of this player

ÁDo not use any non standard shaped CD (heart etc.) avail-

able on the market, because it may damage the player.

ÁDo not use a CD with tape, seals, or paste on it, because

damage to the player may result.

Maintenance

ÁBe sure to press POWER to set the player to the standby

mode and disconnect the AC cord before maintaining the

player.

ÁWipe this player with a dry, soft cloth.

If the surfaces are extremely dirty, wipe clean with a cloth

which has been dipped in a weak soap-and-water solution

and wrung out thoroughly, and then wipe again with a dry

cloth.

ÁNever use alcohol, benzine, thinner, cleaning fluid or other

chemicals. And do not use compressed air to remove dust.

Disc tray

Disc

If the player fails to operate normally, check the following points to determine whether the fault can be corrected by the simple mea-

sures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the AC cord and contact your

authorized YAMAHA dealer or service center for help.

Symptom (Common) Remedy

Troubleshooting

No power.

The player is automatically set to the

standby mode.

ÁPlay fails to start even when PLAY is

pressed.

ÁPlay starts but then stops immediately.

No picture.

ÁNo sound.

ÁDistorted sound.

Picture is distorted during rapid advance

or rapid reverse.

No key operation (by the main unit and/or

the remote control unit) is effective.

No 4:3 (16:9) picture.

No on-screen display.

No operations can be performed with the

remote control unit.

On-Screen Menu Icons not displayed or

only partially displayed on the TV screen.

Insert the AC plug securely into the AC cord.

To conserve power, the player is automatically set to the standby mode after

approx. 30 minutes have elapsed in the stop mode (Auto power-off function). Turn

the power back to ON.

ÁCondensation has formed: wait about 1 to 2 hours to allow the player to dry out.

ÁThis player cannot play a disc other than DVD, Video CD and CD.

ÁThe disc may be dirty and may require cleaning.

ÁEnsure that the disc is installed with the label side up to be played facing upwards.

ÁEnsure that the equipment is connected properly.

ÁEnsure that the input setting for the TV is “Video”.

ÁEnsure that the equipment is connected properly.

ÁEnsure that the input settings for the TV and stereo system are correct.

ÁAdjust the master volume using the On-Screen Menu Icon for player information.

The picture will be somewhat distorted at times: this is normal.

ÁSome operations may be prohibited by the disc.

ÁPress POWER to set the player to the standby mode and then back to ON.

Alternatively, press POWER to set the player to the standby mode, disconnect the

AC plug and then re-connect it. (The player may not be operating properly due to

lightning, static electricity or some other external factor.)

Choose the correct setup “6 TV Aspect” item which matches the TV set used.

The “Off” setting is selected for “1 On-Screen Messages” in “4 On-Screen

Messages”: select “On”.

ÁTo conserve power, the player is automatically set to the standby mode after

approx. 30 minutes have elapsed in the stop mode (Auto power-off function).

Turn the power back to ON.

ÁCheck the batteries are installed with the correct polarities (o and p).

ÁThe batteries are depleted: replace them with new ones.

ÁPoint the remote control unit at the remote control sensor and operate.

ÁOperate the remote control unit at a distance of not more than 23 feet (7 m) from

the remote control sensor.

ÁRemove the obstacles between the remote control unit and remote control sensor.

Change the position of the On-Screen Menu Icon using “2 Color and Position” in

“4 On-Screen Messages” of the initial settings.

For Your Reference

ÁIf the service number fails to be cleared even when the remedial action is taken, ask the service technician to repair the player.

Symptom (DVD) Remedy

Symptom (Video CD) Remedy

No menu play. This function works only for Video CDs with playback control.

Self-diagnosis display function

When an error or trouble is detected during operation, a service number appears in the FL display.

When a service number has appeared, check out the details given below.

Service number

stands

for a number.

Player status

Disc is dirty.

Trouble is likely to have occurred. The

number following “H” differs depending

on the status of the player.

Remedy

Wipe the disc clean.

Press POWER to set the player to the standby mode and then

back to ON. Alternatively, press POWER to set the player to

the standby mode, disconnect the AC cord, and then re-

connect it.

No subtitles.

Alternative audio soundtrack (or subtitle)

languages fail to be selected.

Angle cannot be changed.

Play does not start even when title is

selected.

Audio soundtrack and/or subtitle

language is not the one selected at the

initial settings.

The menu is displayed in French

(example).

No surround sound

The password for rating level has been

forgotten.

ÁSubtitles appear only with discs which contain them.

ÁSubtitles are cleared from the TV monitor. Perform the steps on page 28 to

display the subtitles.

ÁAn alternative language is not selected with discs which do not contain more than

one language.

ÁIn the case of some discs, the alternative language cannot be selected by

operating the AUDIO or SUBTITLE button. Try selecting it from the DVD menu if

one is available.

This function is dependent on software availability. Even if a disc has a number of

angles recorded, these angles may be recorded for specific scenes only (when

“ANGLE” lights up on the player’s FL display).

Confirm the “2 Ratings” setting.

If the audio soundtrack and/or subtitle language does not exist on the disc, the

language selected at the initial settings will not be seen/heard.

The setup “3 Menus” of “1 Disc Languages” is set to French: select English.

Choose the correct setup at the “8 Speaker Setting” which matches your stereo

system.

Reset all the settings to Factory Preset.

While the player is in the stop mode, hold the player’s SKIP (H) button and the

PAUSE button down simultaneously and then hold the OPEN/CLOSE button down

for longer than 3 seconds (until “Initialized” disappears from the TV monitor). The

lock will be released and all initial settings will return to the default values.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. PA PARIS-EST RUE AMBROISE CROIZAT CROISSY-BEAUBOURG BP70-77312 MARNE LAVALLEE, CEDEX 2 FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Japan

Specifications

Signal system: NTSC

Weight: 7.9 lbs. (3.6 kg)

Dimensions: 17

/16w (W)q10

/8w (D)q3

/16w (H)

[435 (W)q263 (D)q100 (H) mm]

(excluding protrusions)

Operating temperature range:

o41 to o95uF (o5 to o35uC)

Operating humidity range:

5 to 90% RH (no condensation)

Discs played:

(1) DVD-VIDEO disc

5w (12 cm) single-sided, single-layer

5w (12 cm) single-sided, dual-layer

5w (12 cm) double-sided, single-layer

3w (8 cm) single-sided, single-layer

3w (8 cm) single-sided, dual-layer

3w (8 cm) double-sided, single-layer

(2) Compact disc (CD-DA, VIDEO CD)

5w (12 cm) disc

3w (8 cm) disc

Component video output:

Y output level: 1 Vp-p (75°)

B output level: 0.7 Vp-p (75°)

R output level: 0.7 Vp-p (75°)

Output connector: Pin jack

(Y; green, C

B; blue, CR; red)

S video output:

Y output level: 1 Vp-p (75°)

C output level: 0.286 Vp-p (75°)

Output connector: S terminal

Number of connectors:1 system

Video output:

Output level: 1 Vp-p (75°)

Output connector: Pin jack

Number of connectors:2 systems

Audio output:

Output level: 2 Vrms (1 kHz, 0 dB)

Output connector: Pin jack

Number of connectors:

5.1ch mixed output (2ch): 1 system

5.1ch discrete output (5.1ch): 1 system

Audio signal output characteristics:

(1) Frequency response:

ÁDVD (linear audio):

2 Hz–22 kHz (48 kHz sampling)

2 Hz–44 kHz (96 kHz sampling)

ÁCD audio: 2 Hz–20 kHz (EIAJ)

(2) S/N ratio:

ÁCD audio: 115 dB (EIAJ)

(3) Dynamic range:

ÁDVD (linear audio):

103 dB

ÁCD audio: 100 dB (EIAJ)

(4) Total harmonic distortion:

ÁCD audio: 0.002% (EIAJ)

Digital audio output:

Optical digital output: Optical connector

Coaxial digital output: Pin jack

PHONES jack:

Output connector: Stereo,

/4w (6.3 mm) jack

Pickup: Wave length: 665 nm

Laser power: CLASS II

Specifications are subject to change without notice.

Weight and dimensions are approximate.

Power

requirements: AC 120 V, 60 Hz

Power

consumption: 19 W (approx. 1.0 W when set to

the standby mode)

Yamaha DVD-S795 de handleiding

Merk: Yamaha

Model: DVD-S795

Categorie: Dvd spelers

Type: de handleiding

PDF downloaden

rapport

in andere talen

English: Yamaha DVD-S795 Owner's manual
italiano: Yamaha DVD-S795 Manuale del proprietario
русский: Yamaha DVD-S795 Инструкция по применению
français: Yamaha DVD-S795 Le manuel du propriétaire
español: Yamaha DVD-S795 El manual del propietario
Deutsch: Yamaha DVD-S795 Bedienungsanleitung
português: Yamaha DVD-S795 Manual do proprietário
dansk: Yamaha DVD-S795 Brugervejledning
čeština: Yamaha DVD-S795 Návod k obsluze
svenska: Yamaha DVD-S795 Bruksanvisning
Türkçe: Yamaha DVD-S795 El kitabı
polski: Yamaha DVD-S795 Instrukcja obsługi
română: Yamaha DVD-S795 Manualul proprietarului

Yamaha DVD-S795 de handleiding

Yamaha DVD-S795 de handleiding

in andere talen

Gerelateerde papieren

Andere documenten