Yamaha MG16 Specificatie

Categorie
Audiomixers
Type
Specificatie

Deze handleiding is ook geschikt voor

1
General Specifications
0 dBu = 0.775 Vrms, Output impedance of signal generator (Rs) = 150 Ω
All level controls are nominal if not specified.
*1 Noise is measured with A-weighting filter.
*2 Crosstalk is measured with 1 kHz band pass filter.
The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download
the manual file.
Frequency Response Input to STEREO OUT +0.5 dB/-1.5 dB (20 Hz to 48 kHz),
refer to the nominal output level @ 1 kHz, GAIN knob: Min
Total Harmonic Distortion
(THD+N)
Input to STEREO OUT 0.03 % @ +14 dBu (20 Hz to 20 kHz), GAIN knob: Min
0.005 % @ +24 dBu (1 kHz), GAIN knob: Min
Hum & Noise
*1
(20 Hz to 20 kHz)
Equivalent Input Noise -128 dBu (Mono Input Channel, Rs: 150 Ω, GAIN knob: Max)
Residual Output Noise -102 dBu (STEREO OUT, STEREO master fader: Min)
Crosstalk(1 kHz)
*2
-78 dB
Input Channels 16 channels: Mono [MIC/LINE]: 8, Mono/Stereo [MIC/LINE]: 2, Stereo [LINE]: 2
Output Channels STEREO OUT: 2, PHONES: 1, MONITOR OUT: 1, AUX SEND: 4, GROUP OUT: 4
Bus STEREO: 1, GROUP: 4, AUX: 4 (MG16XU: incl. FX)
Input Channel Function PAD CH 1 – CH 8 26 dB
HPF CH 1 – CH 8,
CH 9/10 (MIC),
CH 11/12 (MIC)
80 Hz, 12 dB/oct
COMP CH 1 – CH 8 1 knob compressor (Gain/Threshold/Ratio)
Threshold: +22 dBu to -8 dBu, Ratio: 1:1 to 4:1,
Output level: 0 dB to 7 dB, Attack time: approx. 25 msec,
Release time: approx. 300 msec
EQ CH 1 – CH 8 HIGH: Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving
MID: Gain: +15 dB/-15 dB, Frequency: 250 Hz to 5 kHz peaking
LOW: Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving
CH 9/10 –
CH 15/16
HIGH: Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving
MID: Gain: +15 dB/-15 dB, Frequency: 2.5 kHz peaking
LOW: Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving
PEAK LED CH 1 – CH 11/12 LED turns on when post EQ signal reaches 3 dB below clipping level.
Level Meter Pre Monitor LEVEL 2 × 12 -segment LED meter [PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB]
Built-in Effect (MG16XU) SPX Algorithm 24 programs, PARAMETER control: 1, FOOT SW: 1 (FX RTN CH on/off)
USB Audio (MG16XU) 2 IN / 2 OUT USB Audio Class 2.0 compliant, Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit
Phantom Power Voltage +48 V
Power Requirements AC 100-240 V, 50 Hz/60 Hz
Power Consumption 30 W
Dimensions (W × H × D) 444 mm × 130 mm × 500 mm (17.5" × 5.1" × 19.7")
Net Weight MG16XU: 6.8 kg (15.0 lbs), MG16: 6.6 kg (14.6 lbs)
Included Accessory AC Power Cord, Rack-Mount Kit, CUBASE AI DOWNLOAD INFORMATION (MG16XU),
Owner’s Manual, Technical Specifications (this leaflet)
Optional Accessory Foot Switch: FC5 (MG16XU)
Operating Temperature 0 to +40 °C
Analog Input Characteristics
0 dBu = 0.775 Vrms
*1 Sensitivity is the lowest level that will produce an output of +4 dBu (1.228 V) or the nominal output level when the unit is set to maximum gain.
(All level controls are at their maximum position.)
*2 1&Sleeve = GND, 2&Tip = HOT, 3&Ring = COLD
*3 1 = GND, 2 = HOT, 3 = COLD
*4 Tip = Signal, Sleeve = GND
Analog Output Characteristics
0 dBu = 0.775 Vrms
*3 1 = GND, 2 = HOT, 3 = COLD
*5 Tip = HOT, Ring = COLD, Sleeve = GND
Digital Input / Output Characteristics (MG16XU)
Input Jack
PAD
26 dB
GAIN Trim
Position
Actual Load
Impedance
For Use with
Nominal
Input Level
Connector
Sensitivity
*1
Nominal Max. Before Clip
MIC/LINE
1 - 8
OFF
+64 dB
3 kΩ
50–600 Ω
Mics/Lines
-80 dBu
(0.077 mV)
-60 dBu
(0.775 mV)
-40 dBu
(7.75 mV)
Combo jack
*2
(Balanced)
+20 dB
-36 dBu
(12.3 mV)
-16 dBu
(122.8 mV)
+4 dBu
(1.228 V)
ON
+38 dB
-54 dBu
(1.55 mV)
-34 dBu
(15.46 mV)
-14 dBu
(154.6 mV)
-6 dB
-10 dBu
(245 mV)
+10 dBu
(2.451 V)
+30 dBu
(24.51 V)
MIC
9/10, 11/12
+64 dB
3 kΩ 50–600 Ω Mic
-80 dBu
(0.077 mV)
-60 dBu
(0.775 mV)
-40 dBu
(7.75 mV)
XLR-3-31
*3
(Balanced)
+20 dB
-36 dBu
(12.3 mV)
-16 dBu
(122.8 mV)
-6 dBu
(388.2 mV)
LINE
9/10, 11/12
+38 dB
10 kΩ 600 Ω Lines
-54 dBu
(1.55 mV)
-34 dBu
(15.46 mV)
-14 dBu
(154.6 mV)
Phone jack
*4
(Unbalanced)
-6 dB
-10 dBu
(245 mV)
+10 dBu
(2.451 V)
+30 dBu
(24.51 V)
LINE
13/14, 15/16
10 kΩ 600 Ω Lines
-30 dBu
(24.5 mV)
-10 dBu
(245 mV)
+10 dBu
(2.45 V)
Phone jack
*4
RCA pin
(Unbalanced)
Output Terminal
Actual Source
Impedance
For Use with Nominal
Output Level
Connector
Nominal Max. Before Clip
STEREO OUT [L, R] 75 Ω 600 Ω Lines +4 dBu (1.228 V) +24 dBu (12.28 V)
XLR-3-32
*3
Phone jack
*5
(Balanced)
MONITOR OUT [L, R]
GROUP OUT [1 - 4]
AUX SEND [1 - 4]
150 Ω 10 kΩ Lines +4 dBu (1.228 V) +20 dBu (7.750 V)
Phone jack
*5
(Impedance Balanced)
PHONES 110 Ω 40 Ω Phones 3 mW + 3 mW 100 mW + 100 mW Stereo phone jack
Terminal Format Data Length Sampling Frequency Connector
USB USB Audio Class 2.0 16-bit/24-bit 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz USB Standard-B
ZT59140
Technical Specifications
2
Dimensions
Unit: mm
This illustration shows the MG16XU.
444
500
130
128
493
Manual Development Group
© 2014 Yamaha Corporation
Published 08/2016 POLE*.*-01E0
Printed in Malaysia
Block and Level Diagrams
MONO/ST CH INPUT
MONO CH INPUT (MIC/LINE)
ST CH INPUT
MONO CH INPUT MONO/ST CH INPUT
ST CH INPUT
Digital EFFECT
STEREO OUT L
STEREO OUT R
GROUP OUT 1
GROUP OUT 2
GROUP OUT 3
GROUP OUT 4
SEND AUX2
SEND AUX1
SEND AUX4
SEND AUX3
PHONES
MONITOR OUT L
MONITOR OUT R
USB

Documenttranscriptie

ZT59140 Analog Input Characteristics 0 dBu = 0.775 Vrms Input Jack PAD 26 dB GAIN Trim Position Actual Load Impedance For Use with Nominal Sensitivity *1 Nominal Max. Before Clip -80 dBu (0.077 mV) -60 dBu (0.775 mV) -40 dBu (7.75 mV) -36 dBu (12.3 mV) -16 dBu (122.8 mV) +4 dBu (1.228 V) -54 dBu (1.55 mV) -34 dBu (15.46 mV) -14 dBu (154.6 mV) -6 dB -10 dBu (245 mV) +10 dBu (2.451 V) +30 dBu (24.51 V) +64 dB -80 dBu (0.077 mV) -60 dBu (0.775 mV) -40 dBu (7.75 mV) +20 dB -36 dBu (12.3 mV) -16 dBu (122.8 mV) -6 dBu (388.2 mV) +38 dB -54 dBu (1.55 mV) -34 dBu (15.46 mV) -14 dBu (154.6 mV) -10 dBu (245 mV) +10 dBu (2.451 V) +30 dBu (24.51 V) -30 dBu (24.5 mV) -10 dBu (245 mV) +10 dBu (2.45 V) +64 dB OFF Technical Specifications +20 dB MIC/LINE 1-8 50–600 Ω Mics/Lines 3 kΩ +38 dB ON General Specifications MIC 9/10, 11/12 0 dBu = 0.775 Vrms, Output impedance of signal generator (Rs) = 150 Ω All level controls are nominal if not specified. Frequency Response Input to STEREO OUT +0.5 dB/-1.5 dB (20 Hz to 48 kHz), refer to the nominal output level @ 1 kHz, GAIN knob: Min Total Harmonic Distortion (THD+N) Input to STEREO OUT 0.03 % @ +14 dBu (20 Hz to 20 kHz), GAIN knob: Min 0.005 % @ +24 dBu (1 kHz), GAIN knob: Min Hum & Noise *1 (20 Hz to 20 kHz) Equivalent Input Noise -128 dBu (Mono Input Channel, Rs: 150 Ω, GAIN knob: Max) Residual Output Noise -102 dBu (STEREO OUT, STEREO master fader: Min) Crosstalk(1 kHz) *2 -78 dB Input Channels 16 channels: Mono [MIC/LINE]: 8, Mono/Stereo [MIC/LINE]: 2, Stereo [LINE]: 2 Output Channels STEREO OUT: 2, PHONES: 1, MONITOR OUT: 1, AUX SEND: 4, GROUP OUT: 4 Bus STEREO: 1, GROUP: 4, AUX: 4 (MG16XU: incl. FX) Input Channel Function PAD CH 1 – CH 8 26 dB HPF CH 1 – CH 8, CH 9/10 (MIC), CH 11/12 (MIC) 80 Hz, 12 dB/oct COMP CH 1 – CH 8 1 knob compressor (Gain/Threshold/Ratio) Threshold: +22 dBu to -8 dBu, Ratio: 1:1 to 4:1, Output level: 0 dB to 7 dB, Attack time: approx. 25 msec, Release time: approx. 300 msec EQ CH 1 – CH 8 HIGH: Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving MID: Gain: +15 dB/-15 dB, Frequency: 250 Hz to 5 kHz peaking LOW: Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving CH 9/10 – CH 15/16 HIGH: Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving MID: Gain: +15 dB/-15 dB, Frequency: 2.5 kHz peaking LOW: Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving PEAK LED CH 1 – CH 11/12 LED turns on when post EQ signal reaches 3 dB below clipping level. Level Meter Pre Monitor LEVEL 2 × 12 -segment LED meter [PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB] Built-in Effect (MG16XU) SPX Algorithm 24 programs, PARAMETER control: 1, FOOT SW: 1 (FX RTN CH on/off) USB Audio (MG16XU) 2 IN / 2 OUT USB Audio Class 2.0 compliant, Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit Phantom Power Voltage +48 V Power Requirements AC 100-240 V, 50 Hz/60 Hz Power Consumption 30 W Dimensions (W × H × D) 444 mm × 130 mm × 500 mm (17.5" × 5.1" × 19.7") Net Weight MG16XU: 6.8 kg (15.0 lbs), MG16: 6.6 kg (14.6 lbs) Included Accessory AC Power Cord, Rack-Mount Kit, CUBASE AI DOWNLOAD INFORMATION (MG16XU), Owner’s Manual, Technical Specifications (this leaflet) Optional Accessory Foot Switch: FC5 (MG16XU) Operating Temperature 0 to +40 °C *1 Noise is measured with A-weighting filter. *2 Crosstalk is measured with 1 kHz band pass filter. The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file. 1 — LINE 9/10, 11/12 — LINE 13/14, 15/16 — Input Level 3 kΩ 50–600 Ω Mic 10 kΩ 600 Ω Lines 10 kΩ 600 Ω Lines -6 dB — Connector Combo jack *2 (Balanced) XLR-3-31 *3 (Balanced) Phone jack *4 (Unbalanced) Phone jack *4 RCA pin (Unbalanced) *1 Sensitivity is the lowest level that will produce an output of +4 dBu (1.228 V) or the nominal output level when the unit is set to maximum gain. (All level controls are at their maximum position.) *2 1&Sleeve = GND, 2&Tip = HOT, 3&Ring = COLD *3 1 = GND, 2 = HOT, 3 = COLD *4 Tip = Signal, Sleeve = GND Analog Output Characteristics 0 dBu = 0.775 Vrms Actual Source Impedance For Use with Nominal STEREO OUT [L, R] 75 Ω MONITOR OUT [L, R] GROUP OUT [1 - 4] AUX SEND [1 - 4] PHONES Output Terminal Output Level Connector Nominal Max. Before Clip 600 Ω Lines +4 dBu (1.228 V) +24 dBu (12.28 V) XLR-3-32 *3 Phone jack *5 (Balanced) 150 Ω 10 kΩ Lines +4 dBu (1.228 V) +20 dBu (7.750 V) Phone jack *5 (Impedance Balanced) 110 Ω 40 Ω Phones 3 mW + 3 mW 100 mW + 100 mW Stereo phone jack *3 1 = GND, 2 = HOT, 3 = COLD *5 Tip = HOT, Ring = COLD, Sleeve = GND Digital Input / Output Characteristics (MG16XU) Terminal Format Data Length Sampling Frequency Connector USB USB Audio Class 2.0 16-bit/24-bit 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz USB Standard-B Block and Level Diagrams Dimensions STEREO OUT L MONO CH INPUT (MIC/LINE) STEREO OUT R 128 444 130 GROUP OUT 1 MONO/ST CH INPUT GROUP OUT 2 GROUP OUT 3 GROUP OUT 4 ST CH INPUT 500 SEND AUX2 493 SEND AUX1 SEND AUX3 SEND AUX4 USB Digital EFFECT PHONES MONITOR OUT L Unit: mm This illustration shows the MG16XU. MONITOR OUT R MONO CH INPUT MONO/ST CH INPUT ST CH INPUT Manual Development Group © 2014 Yamaha Corporation Published 08/2016 POLE*.*-01E0 Printed in Malaysia 2
  • Page 1 1
  • Page 2 2

Yamaha MG16 Specificatie

Categorie
Audiomixers
Type
Specificatie
Deze handleiding is ook geschikt voor