Documenttranscriptie

ZT57280 MIXING CONSOLE Analog Input Characteristics Input Jacks PAD 26 dB GAIN Trim Position Actual Load Impedance For Use With Nominal Input level Sensitivity *1 Nominal Max. before clip -72 dBu (0.195 mV) -60 dBu (0.775 mV) -40 dBu (7.75 mV) -28 dBu (30.9 mV) -16 dBu (122.8 mV) +4 dBu (1.228 mV) -46 dBu (3.884 mV) -34 dBu (15.46 mV) -14 dBu (154.6 mV) -6 dB -2 dBu (615.6 mV) +10 dBu (2.451 V) +30 dBu (24.51 V) - -22 dBu (61.56 mV) -10 dBu (245.1 mV) +10 dBu (2.451 V) +64 dB OFF +20 dB Technical Specifications General Specifications MIC/LINE 1 – 4 +38 dB ON - All level knobs are nominal if not specified. Input to STEREO OUT Total Harmonic Distortion (THD+N) Input to STEREO OUT Hum&Noise *1 (20 Hz to 20 kHz) +0.5 dB/-1.0 dB (20 Hz to 48 kHz), refer to the nominal output level @1 kHz, GAIN knob: Min 0.02 % @ +14 dBu (20 Hz to 20 kHz), GAIN knob: Min % @ +24 dBu (1 kHz), GAIN knob: Min 10 kΩ 600 Ω Lines LINE 9/10 Combo jack*2 (Balanced) Phone jack *3 RCA Pin (Unbalanced) Phone jack *3 (Unbalanced) 0 dBu is referenced to 0.775 Vrms. 0.003 *1 Sensitivity is the lowest level that will produce an output of +4dBu (1.228V) or the nominal output level when the unit is set to maximum gain (all level knobs are maximum position). Equivalent Input Noise -128 dBu (Mono Input Channel, Rs: 150 Ω, GAIN knob: Max) *2 1&Sleeve = Ground, 2&Tip = Hot, 3&Ring = Cold Residual Output Noise -102 dBu (STEREO OUT, STEREO LEVEL knob: Min) *3 Tip = Signal, Sleeve = Ground -83 dB Crosstalk (1 kHz) *2 Input Channels 10 channels: Mono [MIC/LINE]: 4, Stereo [LINE]: 3 Ouput Channels STEREO OUT: 2, PHONES: 1, MONITOR OUT: 1, AUX (FX) SEND: 1 Bus Stereo: 1, AUX (FX): 1 Analog Output Characteristics Output Terminals Actual Source Impedance For Use With Nominal Max. before clip Connector CH1 – CH4 HPF CH1 – CH4 80 Hz, 12 dB/oct STEREO OUT [L, R] 75 Ω 600 Ω Lines +4 dBu (1.228 V) +24 dBu (12.28 V) XLR-3-32 *1 Phone jack *2 (Balanced) CH1 – CH2 1-knob compressor Threshold: +22 dBu to -8 dBu, Ratio:1:1 to 4:1, Output level: 0 dB to 7 dB, Attack time: approx. 25 msec, Release time: approx. 300 msec MONITOR OUT [L, R] AUX (FX) SEND 150 Ω 10 kΩ Lines +4 dBu (1.228 V) +20 dBu (7.750 V) Phone jack *2 (Impedance Balanced) CH1 – CH9/10 HIGH: Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving PHONES 110 Ω 40 Ω Lines 3 mW + 3 mW 100 mW + 100 mW Stereo phone jack CH1 – CH4 MID: Gain: +15 dB/-15 dB, Frequency: 2.5 kHz peaking 0 dBu is referenced to 0.775 Vrms. CH1 – CH9/10 LOW: Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving *1 1 = Ground, 2 = Hot, 3 = Cold PEAK LED CH1 – CH4 LED turns on when post EQ signal reaches 3 dB below clipping (+17 dBu) Level Meter Post STEREO LEVEL Knob 2×7 -segment LED meter [PEAK (+17), +10, +6, 0, -6, -10, -20 dB] Internal Digital Effect (MG10XU) SPX Algorithm 24 programs USB Audio (MG10XU) 2 IN / 2 OUT Input Channel Function EQ 26 dB Output level Nominal PAD COMP 1 50-600 Ω Mics/Lines LINE 5/6, 7/8 0 dBu = 0.775 Vrms Output impedance of signal generator (Rs) = 150Ω Frequency Response 3 kΩ Connector USB Audio Class 2.0 compliant Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit *2 Tip = Hot, Ring = Cold, Sleeve = Ground Digital Input / Output Characteristics Output Terminals USB Format USB Audio Class 2.0 Fs Connector 16 /24 bit 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz USB Standard-B *1 Data length depends on the particular audio format being used. USB Audio Class2.0: 16 / 24-bit, Yamaha Steinberg USB Driver: 24-bit Phantom Power Voltage +48 V Power Supply Adaptor PA-10 (AC 38 VCT, 0.62A, Cable length = 3.6 m) or equivalent recommended by Yamaha Power Consumption 22.9 W Dimensions (W×H×D) 244 mm×71 mm×294 mm (9.6” × 2.8” × 11.6”) 1 A (after a supply interruption of 5s) Net Weight MG10XU: 2.1 kg (4.6 lbs.), MG10: 1.9 kg (4.1 lbs.) Conforms to Environments: E1, E2, E3 and E4 Included Accessory AC Adaptor, Cubase AI Download Information (MG10XU), Owner’s Manual, Precautions, Technical Specifications (this leaflet) Optional Accessory Mic Stand Adaptor: BMS-10A Operating Temperature 0 to +40°C *1 Noise is measured with A-weighting filter. *2 Crosstalk is measured with 1 kHz band pass filter. Data Length*1 European Models Inrush Current based on EN 55103-1:2009 1 A (on initial switch-on) * The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file. See reverse side for block/level diagrams and dimensions.  Block and Level Diagrams Dimensions Unit: mm 80Hz 71 65 244 2 294 292 30 28 This illustration shows the MG10XU. 2 Manual Development Department © 2013 Yamaha Corporation Published 03/2016 MWLE*.*- **C0 Printed in Malaysia