Zebra FLB3578 Referentie gids

Type
Referentie gids
FLB3508/3578 Cradle
Quick Reference Guide
2 FLB3508/3578 Cradle
No part of this publication may be reproduced or used in any form, or by any
electrical or mechanical means, without permission in writing from Zebra. This
includes electronic or mechanical means, such as photocopying, recording, or
information storage and retrieval systems. The material in this manual is subject to
change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware,
furnished to the user is on a licensed basis. Zebra grants to the user a
non-transferable and non-exclusive license to use each software or firmware
program delivered hereunder (licensed program). Except as noted below, such
license may not be assigned, sublicensed, or otherwise transferred by the user
without prior written consent of Zebra. No right to copy a licensed program in whole
or in part is granted, except as permitted under copyright law. The user shall not
modify, merge, or incorporate any form or portion of a licensed program with other
program material, create a derivative work from a licensed program, or use a
licensed program in a network without written permission from Zebra. The user
agrees to maintain Zebra’s copyright notice on the licensed programs delivered
hereunder, and to include the same on any authorized copies it makes, in whole or in
part. The user agrees not to decompile, disassemble, decode, or reverse engineer
any licensed program delivered to the user or any portion thereof.
Zebra reserves the right to make changes to any software or product to improve
reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise
under any Zebra intellectual property rights. An implied license only exists for
equipment, circuits, and subsystems contained in Zebra products.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The
Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra
Technologies company.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.www.zebra.com/warranty
.
Quick Reference Guide 3
Introduction
The FLB3508/3578 cordless scanner cradle acts as a stand, host communication
interface and charger for the LS3578 cordless scanner. It attaches to a mounting
bracket using three isolators. The bracket is then mounted on the forklift surface.
The FLB3578 cradle receives data from the scanner via a Bluetooth radio, and sends
that data to the host through an attached cable. The cradle also charges the scanner’s
internal battery pack when the scanner is inserted. A portable power supply on the
forklift supplies power to the cradle.
This document provides basic instructions on setting up and using the cradle.
CAUTION
LS3478 cordless scanners are incompatible with FLB3508/3578
cradles. LS3578 cordless scanners are incompatible with FLB3408/3478
cradles.
Equipment Supplied
The cradle package includes:
Cradle
Mounting bracket with isolators
Three 8-32 x 1.5" Philips head screws (for attaching cradle to mounting bracket).
Accessories
The following equipment may be needed:
Four 1/4-20 screws, minimum length 1.0" (for fastening bracket to mounting
surface).
Save the shipping container for storing or shipping. Inspect all equipment for damage. If
anything is damaged or missing, call an authorized Zebra business Support Center
immediately.
Related Documentation
LS3578 Product Reference Guide, p/n 72-93911-xx.
LS3578 Quick Start Guide, p/n 72-93587-xx.
This documentation is available at: http://www.zebra.com/support.
4 FLB3508/3578 Cradle
Cradle Parts
The Mounting Bracket
The mounting bracket is used to install the cradle on a forklift. Mount the bracket so that
the cradle is within the user’s reach envelope. The recommended reach envelope has a
radius of 15" measured from the front of the user’s shoulder to the scanner grip.
Three isolators ensure secure attachment with minimized vibration. The bracket has
holes that provide access the host and power ports, and enable securing the cables
Mounting
Screw Hole
(2)
Charging/
Communication
Contacts
Latch
Pairing
Bar Code
Mounting
Screw Hole
Power Cable
Groove
Mounting
Screw Hole
Cable
Hook
Power Port
Host Port
Host Cable
Groove
Mounting
Screw Hole
Converter
Knob
Latch
Back
Front
LED
Quick Reference Guide 5
with cable ties.
CAUTION
Ensure the Converter Knob is in the position shown above. If not, rotate the
knob counterclockwise to activate latches.
Mounting Bracket
Cable
Access
Hole
Cable Tie
Holes
Isolator
Cable Tie
Holes
Cable Tie
Holes
Isolator
Isolator
Converter Knob
6 FLB3508/3578 Cradle
Cradle Connections
IMPORTANT
Connect the interface cable and power supply (if necessary) in the
following order to ensure proper operation of the scanner and cradle.
1. Insert the interface cable from the host computer into the cradle’s host port.
2.Connect the forklift power supply to the
cradle’s power port, if applicable.
3.Optional: Thread the host cable over the
cable hook and run the host and power
cables into their respective cable grooves, or
use cable ties to secure them to the
mounting plate after it is attached to the
cradle (see Mounting the Cradle on the
Forklift).
4.Pair the scanner with the cradle by
scanning the pairing bar code on the cradle.
5.If necessary, scan the appropriate host bar
code (for non-autodetected interfaces). See
the Product Reference Guide.
Changing the Host Interface
To connect to a different host, or to the same
host through a different cable:
1.Unplug the power supply from the cradle, if
used.
2.Unplug the interface cable from the host.
3.Connect the interface cable to the new
host, or the new interface cable to the
existing host.
4. Reconnect the power supply, if required.
5. If necessary, scan the appropriate host bar code (for non-autodetected interfaces).
Refer to the Product Reference Guide.
CAUTION
If the scanner does not recognize the host, disconnect the power supply, then
reconnect after connecting the host cable.
Host
Port
Power Port
Quick Reference Guide 7
Mounting the Cradle on the Forklift
1. Consult an environmental health and safety
manager to determine
an appropriate mounting location within the
recommended 15" reach envelope.
2. Ensure the converter knob is in the correct
position (see Caution in The Mounting
Bracket section).
3. Attach the host and power cables to the
appropriate ports (see Cradle Connections).
4. Position the cradle with the screw holes in the
cradle aligning with the holes in the isolators.
5. Attach the cradle to the bracket using three
8-32 x 1.5" Philips screws through the cradle
and isolator holes.
6. Mark the mounting surface through the four
screw holes on the mounting bracket, or use
the mounting template to determine the
location of the screw holes.
7. Pre-drill holes into the mounting surface to
accommodate four 1/4-20, minimum 1.0"
length, Philips head screws.
8. If desired, thread cable ties through the holes
on each side of the bracket and secure the
host and power cables along the edges of the
bracket.
9. Attach the bracket to the mounting surface.
10.Place the scanner in the cradle.
15" Radius
Side View, Standing
Top View
Side View, Seated
Reach Envelope
15" Radius
15" Radius
8 FLB3508/3578 Cradle
Inserting the Scanner in the Cradle
To insert the scanner in the cradle, insert the scanner top first. Then, push the handle
until it clicks into place, engaging the contacts in the cradle and scanner.
Sending Data to the Host Computer
The cradle receives data from the scanner via a wireless radio connection and
transmits it to the host computer via the host cable. The scanner and cradle must be
paired for successful wireless communication.
Pairing
Pairing registers a scanner to the cradle such that the scanner and cradle can
exchange information. The FLB3578 operates in two modes: scanner-to-cradle and
multi scanner-to-cradle. In scanner-to-cradle mode, the scanner is paired to the cradle
either by insertion into the cradle (if pairing on insertion is enabled), or by scanning the
pairing bar code. In multi scanner-to-cradle mode, up to three scanners can be paired
to one cradle. A multipoint bar code must be scanned to activate this feature.
The cradle includes a pairing bar code on its front. To pair the scanner with the cradle,
scan the pairing bar code. A high-low-high-low beep sequence followed by a low-high
beep sequence indicates successful pairing and connection to the remote device. A
long low, long high beep sequence indicates unsuccessful pairing. Refer to the Product
Reference Guide for more information.
Lost Connection to Host
If scanned data does not transmit to the cradle’s host, ensure that all cables are firmly
inserted and the power supply is connected to an appropriate AC outlet, if applicable.
If scanned data still does not transmit to the host, reestablish a connection with the
host:
1. Disconnect the power supply from the cradle.
2. Disconnect the host interface cable from the cradle.
3. Wait three seconds.
4. Reconnect the host interface cable to the cradle.
5. Reconnect the power supply to the cradle, if required.
6. Reestablish pairing with the cradle by scanning the pairing bar code.
NOTE
The FLB3578 does not always require a power supply, depending on
the host interface.
Charging the Scanner Battery in the Cradle
To charge the scanner battery, place the scanner in the cradle (see Inserting the
Scanner in the Cradle). The battery begins charging when the scanner LED indicator
starts flashing green. A complete charge of a fully discharged battery can take up to
four hours using external power and up to 10 hours using the interface cable.
Quick Reference Guide 9
Scanner LED Indicators
The green LED on the scanner indicates charging activity (see the table below). If the
scanner is charging in fast mode (non-bus powered mode), the green LED blinks at a
fast rate. If the scanner is charging in slow mode (bus-powered mode), the LED blinks
at a slow rate. If the red LED on the scanner begins flashing, indicating a charging
problem, remove the scanner from the cradle and replace the battery. If the red LED
continues flashing, contact a Zebra business Support Center.
Using a Host Interface to Supply Power
Some hosts can provide power to the cradle via the host interface, instead of an
external power supply.
Troubleshooting
If the cradle does not work after following the previous procedures:
Check the system power.
Check for loose cable connections.
Check that the scanner is inserted properly in the cradle.
Check that the host settings are correct and the cradle is connected to the
appropriate port on the host.
CAUTION
Do not pour, spray, or spill any liquid on the cradle.
Mounting Template
Refer to the English version of this guide (p/n 72-94604-xx ) for a mounting
template.
Standard Scanner Use LED Sequences
Off No power applied to scanner (battery is discharged or removed); scanner is
in low power and ready to scan.
Green A bar code was successfully decoded.
Red A data transmission error; scanner malfunction; or, LS3578 cordless scanner
was inserted into a STB3478 cradle.
Charging Use LED Sequences
Green Slow Flash The scanner
charges at the slow rate (used when the cradle is
powered by the host cable).
Green Fast Flash The scanner charges at the fast rate (used when cradle is
powered from an external power supply).
Red Flash Charging problem. Refer to the Product Reference Guide for
more information.
Red and Green
Flash
Temperature fault.
10 FLB3508/3578 Cradle
Health and Safety Recommendations
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the
recommendations below. Consult with your local Health & Safety Manager to ensure that you
are adhering to your company’s safety programs to prevent employee injury.
Reduce or eliminate repetitive motion
Maintain a natural position
Reduce or eliminate excessive force
Keep objects that are used frequently within easy reach
Perform tasks at correct heights
Reduce or eliminate vibration
Reduce or eliminate direct pressure
Provide adjustable workstations
Provide adequate clearance
Provide a suitable working environment
Improve work procedures.
ידי-לע רשואמה חתמ לבכב קר שמתשה Zebra םגדמ UL LISTED ITE (IEC/EN 60950-1 ,
LPS/SELV) חתמ יגוריד םע:
טלפ 9-15 VDC, םומינימ 1.5 A, לש תילמיסקמ הרוטרפמט םע 40° C. חוכ קפסב שומיש םומינימ
ןכוסמ תויהל לולעו וז הדיחיל ונתינש םהשלכ םירושיא תלילשל םורגי יפולח.
Quick Reference Guide 11
Eurasian Customs Union
Евразийский Таможенный Союз
Данный продукт соответствует требованиям знака EAC.
12 FLB3508/3578 Cradle
Waste Electrical and Electronic Equipment (WEEE)
Български: За клиенти от ЕС: След края на полезния им живот всички продукти трябва
да се връщат на Zebra за рециклиране. За информация относно връщането на
продукти, моля отидете на адрес: http://www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich ž
ivotnosti vrátit
spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové
stránce: http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er
udtjent. Læs oplysningerne om returnering af produkter på:
http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müs
sen am Ende ihrer Lebensdauer
zum Recycling an Zebra zurückgesandt werden. Informationen zur Rücksendung von
Produkten finden Sie unter http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους,
πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες
σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση
http://www.zebra.com/weee στο ∆ιαδίκτυο.
Eesti: EL klientidele: kõik
tooted tuleb nende eluea lõppedes tagastada taaskasutamise
eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun
aadressi: http://www.zebra.com/weee.
English: For EU Customers: All products at the end of their life must be returned to Zebra for
recycling. For information on how to return product, please go to:
http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra
al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo
devolver un producto, visite: http://www.zebra.com/weee.
Français: Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être
retournés à Zebra pour recyclage. Pour de plus amples informations sur le retour de produits,
consultez : http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita
devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle
modalità di restituzione, visitare il seguente sito Web:
http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ
Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu,
skatiet: http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti
utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite:
http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell
eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos
tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom,
iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-
prodott, jekk jogħġbok żur: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur
naar Zebra te worden teruggezonden voor recycling. Raadpleeg
http://www.zebra.com/weee voor meer informatie over het terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ
do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na
stronie internetowej http://www.z
ebra.com/weee.
Quick Reference Guide 13
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à
Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite:
http://www.zebra.com/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare,
trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre returnarea produsului,
accesaţi: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju
Zebra za reciklažo. Za informacije o vračilu izdelka obiščite:
http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich
životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov
nájdete na: http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi
Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on
osoitteessa http://www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till
Zebra för återvinning. Information om hur du returnerar produkten finns på
http://www.zebra.com/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya
iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin:
http://www.zebra.com/weee.
14 FLB3508/3578 Cradle
If you have a problem using the equipment, contact your facility’s Technical or
Systems Support. If there is a problem with the equipment, they will contact the
Zebra Support at: http://www.zebra.com/support
.
For the latest version of this guide go to: http://www.zebra.com/support
.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many
jurisdictions worldwide. All other trademarks are the property of their respective
owners.
©2017 Symbol Technologies LLC, a subsidiary of Zebra Technologies
Corporation. All rights reserved.
72E-94604-03HE Revision A - March 2017
Service Information
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Zebra FLB3578 Referentie gids

Type
Referentie gids

in andere talen